488 lines
17 KiB
Plaintext
488 lines
17 KiB
Plaintext
-- *****************************************************************
|
|
-- CISCO-CPRI-MIB.my
|
|
-- CPRI INTERFACE MIB
|
|
--
|
|
-- September 2020, Rajarshi Chakraborty (rajarcha)
|
|
--
|
|
-- Copyright (c) 2020 by Cisco Systems, Inc.
|
|
-- All rights reserved.
|
|
-- *****************************************************************
|
|
|
|
CISCO-CPRI-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE,
|
|
NOTIFICATION-TYPE,
|
|
Integer32,
|
|
Counter32,
|
|
Unsigned32,
|
|
Counter64
|
|
FROM SNMPv2-SMI
|
|
TEXTUAL-CONVENTION,
|
|
TruthValue,
|
|
RowStatus,
|
|
StorageType,
|
|
DisplayString,
|
|
MacAddress,
|
|
TimeStamp
|
|
FROM SNMPv2-TC
|
|
MODULE-COMPLIANCE,
|
|
OBJECT-GROUP,
|
|
NOTIFICATION-GROUP
|
|
FROM SNMPv2-CONF
|
|
ifIndex,
|
|
ifName
|
|
FROM IF-MIB
|
|
ciscoMgmt
|
|
FROM CISCO-SMI;
|
|
|
|
ciscoCpriMIB MODULE-IDENTITY
|
|
LAST-UPDATED "202009100000Z"
|
|
ORGANIZATION "Cisco Systems, Inc."
|
|
CONTACT-INFO
|
|
"Cisco Systems
|
|
Customer Service
|
|
|
|
Postal: 170 W Tasman Drive
|
|
San Jose, CA 95134
|
|
USA
|
|
|
|
Tel: +1 800 553-NETS
|
|
|
|
E-mail: cs-<list>@cisco.com"
|
|
DESCRIPTION
|
|
"This MIB module defines the managed objects for physical layer
|
|
characteristics of cpri interfaces and performance
|
|
statistics objects for protocol specific counters in falidae
|
|
devices.
|
|
Glossary:
|
|
TX : Transmit
|
|
RX : Receive "
|
|
REVISION "202009100000Z"
|
|
DESCRIPTION "Initial version of the MIB module."
|
|
::= { ciscoMgmt 9999 }
|
|
|
|
|
|
-- Textual Conventions definition will be defined before this line
|
|
|
|
-- MIB Notification Definitions
|
|
|
|
ciscoCpriMIBNotifs OBJECT IDENTIFIER
|
|
::= { ciscoCpriMIB 0 }
|
|
|
|
-- MIB Object Definitions
|
|
|
|
ciscoCpriMIBObjects OBJECT IDENTIFIER
|
|
::= { ciscoCpriMIB 1 }
|
|
|
|
coiCpriController OBJECT IDENTIFIER
|
|
::= { ciscoCpriMIBObjects 1 }
|
|
|
|
coiCpriRoeStats OBJECT IDENTIFIER
|
|
::= { ciscoCpriMIBObjects 2 }
|
|
|
|
coiCpriControllerTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CoiCpriControllerEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table provides management information for cpri layer
|
|
related attributes of interfaces with an ifType of
|
|
cpri"
|
|
::= { coiCpriController 1 }
|
|
|
|
coiCpriControllerEntry OBJECT-TYPE
|
|
SYNTAX CoiCpriControllerEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry containing management information on cpri layer
|
|
related attributes of interfaces with an ifType
|
|
cpri. Entries are created by the feature when a
|
|
new interface is added. Entries are deleted by the agent
|
|
when an interface is removed."
|
|
INDEX { ifIndex }
|
|
::= { coiCpriControllerTable 1 }
|
|
|
|
|
|
CoiCpriControllerEntry ::= SEQUENCE {
|
|
coiCpriControllerSupportedRateList BITS,
|
|
coiCpriControllerConfiguredRateList BITS,
|
|
coiCpriControllerNegotiatedRate INTEGER,
|
|
coiCpriControllerPortRole INTEGER,
|
|
coiCpriControllerL1StartupTimer Unsigned32,
|
|
coiCpriControllerAdminStatus INTEGER,
|
|
coiCpriControllerOperStatus INTEGER,
|
|
coiCpriControllerLoopbackInfo INTEGER,
|
|
coiCpriControllerAlarmStatus BITS
|
|
}
|
|
|
|
coiCpriControllerSupportedRateList OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
rate614Mbps(0),
|
|
rate1228Mbps(1),
|
|
rate2457Mbps(2),
|
|
rate3072Mbps(3),
|
|
rate4915Mbps(4),
|
|
rate6144Mbps(5),
|
|
rate9830Mbps(6),
|
|
rate8110Mbps(7),
|
|
rate10137Mbps(8),
|
|
rate12165Mbps(9),
|
|
rate24330Mbps(10)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the current supported rate list of the
|
|
cpri controller, valid values are :
|
|
rate614Mbps(0): CPRI option 1 - 614 Mbps
|
|
rate1228Mbps(1): CPRI option 2 - 1228 Mbps
|
|
rate2457Mbps(2): CPRI option 3 - 2457 Mbps
|
|
rate3072Mbps(3): CPRI option 4 - 3072 Mbps
|
|
rate4915Mbps(4): CPRI option 5 - 4915 Mbps
|
|
rate6144Mbps(5): CPRI option 6 - 6144 Mbps
|
|
rate9830Mbps(6): CPRI option 7 - 9830 Mbps
|
|
rate8110Mbps(7): CPRI option 7A - 8110 Mbps
|
|
rate10137Mbps(8): CPRI option 8 - 10137 Mbps
|
|
rate12165Mbps(9): CPRI option 9 - 12165 Mbps
|
|
rate24330Mbps(10): CPRI option 10 - 24330 Mbps "
|
|
::= { coiCpriControllerEntry 1 }
|
|
|
|
coiCpriControllerConfiguredRateList OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
rate614Mbps(0),
|
|
rate1228Mbps(1),
|
|
rate2457Mbps(2),
|
|
rate3072Mbps(3),
|
|
rate4915Mbps(4),
|
|
rate6144Mbps(5),
|
|
rate9830Mbps(6),
|
|
rate8110Mbps(7),
|
|
rate10137Mbps(8),
|
|
rate12165Mbps(9),
|
|
rate24330Mbps(10)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the current configured rate list of the
|
|
cpri controller. Maximum 4 values can be configured at a time
|
|
on a port. Valid values are :
|
|
rate614Mbps(0): CPRI option 1 - 614 Mbps
|
|
rate1228Mbps(1): CPRI option 2 - 1228 Mbps
|
|
rate2457Mbps(2): CPRI option 3 - 2457 Mbps
|
|
rate3072Mbps(3): CPRI option 4 - 3072 Mbps
|
|
rate4915Mbps(4): CPRI option 5 - 4915 Mbps
|
|
rate6144Mbps(5): CPRI option 6 - 6144 Mbps
|
|
rate9830Mbps(6): CPRI option 7 - 9830 Mbps
|
|
rate8110Mbps(7): CPRI option 7A - 8110 Mbps
|
|
rate10137Mbps(8): CPRI option 8 - 10137 Mbps
|
|
rate12165Mbps(9): CPRI option 9 - 12165 Mbps
|
|
rate24330Mbps(10): CPRI option 10 - 24330 Mbps "
|
|
::= { coiCpriControllerEntry 2 }
|
|
|
|
coiCpriControllerNegotiatedRate OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
rateNone(0),
|
|
rate614Mbps(1),
|
|
rate1228Mbps(2),
|
|
rate2457Mbps(3),
|
|
rate3072Mbps(4),
|
|
rate4915Mbps(5),
|
|
rate6144Mbps(6),
|
|
rate9830Mbps(7),
|
|
rate8110Mbps(8),
|
|
rate10137Mbps(9),
|
|
rate12165Mbps(10),
|
|
rate24330Mbps(11)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the current negotiated rate of the
|
|
cpri controller, valid values are -
|
|
rateNone(0): No valid negotiated rate
|
|
rate614Mbps(1): The negotiated rate is 614 Mbps
|
|
rate1228Mbps(2): The negotiated rate is 1228 Mbps
|
|
rate2457Mbps(3): The negotiated rate is 2457 Mbps
|
|
rate3072Mbps(4): The negotiated rate is 3072 Mbps
|
|
rate4915Mbps(5): The negotiated rate is 4915 Mbps
|
|
rate6144Mbps(6): The negotiated rate is 6144 Mbps
|
|
rate9830Mbps(7): The negotiated rate is 9830 Mbps
|
|
rate8110Mbps(8): The negotiated rate is 8110 Mbps
|
|
rate10137Mbps(9): The negotiated rate is 10137 Mbps
|
|
rate12165Mbps(10): The negotiated rate is 12165 Mbps
|
|
rate24330Mbps(11): The negotiated rate is 24330 Mbps "
|
|
::= { coiCpriControllerEntry 3 }
|
|
|
|
coiCpriControllerPortRole OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
slave(0),
|
|
master(1)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the role of the cpri
|
|
controller, valid values are -
|
|
slave(0): The port mode is slave
|
|
master(1): The port mode is master "
|
|
::= { coiCpriControllerEntry 4 }
|
|
|
|
coiCpriControllerL1StartupTimer OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is gives the L1 Startup Timer value
|
|
of the cpri controller (in terms of milliseconds). "
|
|
::= { coiCpriControllerEntry 5 }
|
|
|
|
coiCpriControllerAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
down(0),
|
|
up(1)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the administration status
|
|
of the cpri interfaces. when it is set to down(0),
|
|
it results in Tx being stopped and there should be
|
|
corresponding change in coiCpriControllerOperStatus.
|
|
Valid values are :
|
|
down(0): The controller is in down state.
|
|
up(1): The controller is in up state"
|
|
::= { coiCpriControllerEntry 6 }
|
|
|
|
coiCpriControllerOperStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
down(0),
|
|
up(1)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the current operational state of the
|
|
cpri controller, valid values are -
|
|
down(0): The controller is in down state.
|
|
up(1): The controller is in up state.
|
|
If coiCpriControllerAdminStatus is down(0) then
|
|
coiCpriControllerOperStatus should be down(0). If
|
|
coiCpriControllerAdminStatus is changed to up(1) then
|
|
coiCpriControllerOperStatus should change to up(1), provided
|
|
the controller is operational and ready to transmit traffic.
|
|
It should remain in down(0) if there is a fault that prevents
|
|
it from going to the up(1) state. "
|
|
::= { coiCpriControllerEntry 7 }
|
|
|
|
coiCpriControllerLoopbackInfo OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
loopbackNone(0),
|
|
loopbackLine(1),
|
|
loopbackInternal(2)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the loopback value of the cpri controller,
|
|
valid values are -
|
|
loopbackNone(0): No controller loopback info
|
|
loopbackLine(1): The controller loopback info is line level
|
|
loopbackInternal(2): The controller loopback info is internal level. "
|
|
::= { coiCpriControllerEntry 8 }
|
|
|
|
coiCpriControllerAlarmStatus OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
noAlarm(0),
|
|
los(1),
|
|
lof(2),
|
|
rai(3),
|
|
sdi(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the current defect status of the cpri
|
|
controller. Valid values are -
|
|
noAlarm(0): No Alarm. This bit will be set when none of the
|
|
following defect bits are set.
|
|
los(1): LOS (Loss Of Signal). This bit will be set when
|
|
LOS alarm condition is detected on the CPRI Rx side.
|
|
lof(2): LOF (Loss Of Frame). This bit will be set when
|
|
LOF alarm condition is detected on the CPRI Rx side.
|
|
rai(3): RAI (Remote Alarm Indication). This bit will be
|
|
set when RAI alarm condition reported in a control
|
|
word.
|
|
sdi(4): SDI (SAP Defect Indication). This bit will be set
|
|
when SDI alarm condition reported in a control
|
|
word."
|
|
::= { coiCpriControllerEntry 9 }
|
|
|
|
coiCpriRoeStatsTable OBJECT IDENTIFIER
|
|
::= { coiCpriRoeStats 1 }
|
|
|
|
coiCpriRoeStatsEntry OBJECT-TYPE
|
|
SYNTAX CoiCpriRoeStatsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry containing stas information on CPRI
|
|
controller ROE port."
|
|
INDEX { ifIndex }
|
|
::= { coiCpriRoeStatsTable 1 }
|
|
|
|
CoiCpriRoeStatsEntry ::= SEQUENCE {
|
|
coiCpriRoeRxFrames Counter64,
|
|
coiCpriRoeDroppedFramesDetected Counter64,
|
|
coiCpriRoeStrayFramesDetected Counter64,
|
|
coiCpriRoeDuplicateFramesDetected Counter64,
|
|
coiCpriRoeOutOfSeqFramesDetected Counter64,
|
|
coiCpriRoeOutOfSeqFramesDropped Counter64,
|
|
coiCpriRoeTxFrames Counter64,
|
|
coiCpriRoeIdleFramesSent Counter64,
|
|
coiCpriRoePktDelayVarMinVal Counter64,
|
|
coiCpriRoePktDelayVarMaxVal Counter64,
|
|
coiCpriRoePktDelayVarAvgVal Counter64,
|
|
coiCpriRoeLineCodeViolationDetected Counter64,
|
|
coiCpriRoeLineCodeViolationPropagated Counter64,
|
|
coiCpriRoeErroredLengthFrames Counter64
|
|
}
|
|
|
|
coiCpriRoeRxFrames OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE frames received."
|
|
::= { coiCpriRoeStatsEntry 1 }
|
|
|
|
coiCpriRoeDroppedFramesDetected OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE frames dropped."
|
|
::= { coiCpriRoeStatsEntry 2 }
|
|
|
|
coiCpriRoeStrayFramesDetected OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE stray frame detected."
|
|
::= { coiCpriRoeStatsEntry 3 }
|
|
|
|
coiCpriRoeDuplicateFramesDetected OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE duplicate frame detected."
|
|
::= { coiCpriRoeStatsEntry 4 }
|
|
|
|
coiCpriRoeOutOfSeqFramesDetected OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE out of sequence frame
|
|
detected."
|
|
::= { coiCpriRoeStatsEntry 5 }
|
|
|
|
coiCpriRoeOutOfSeqFramesDropped OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE out of sequence frames
|
|
dropped."
|
|
::= { coiCpriRoeStatsEntry 6 }
|
|
|
|
coiCpriRoeTxFrames OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE frames transmitted."
|
|
::= { coiCpriRoeStatsEntry 7 }
|
|
|
|
coiCpriRoeIdleFramesSent OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of idle frames sent."
|
|
::= { coiCpriRoeStatsEntry 8 }
|
|
|
|
coiCpriRoePktDelayVarMinVal OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the RoE packet-delay-variation
|
|
min value."
|
|
::= { coiCpriRoeStatsEntry 9 }
|
|
|
|
coiCpriRoePktDelayVarMaxVal OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the RoE packet-delay-variation
|
|
max value."
|
|
::= { coiCpriRoeStatsEntry 10 }
|
|
|
|
coiCpriRoePktDelayVarAvgVal OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the RoE packet-delay-variation
|
|
avg value."
|
|
::= { coiCpriRoeStatsEntry 11 }
|
|
|
|
coiCpriRoeLineCodeViolationDetected OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of line-code-violation-detected
|
|
on CPRI link."
|
|
::= { coiCpriRoeStatsEntry 12 }
|
|
|
|
coiCpriRoeLineCodeViolationPropagated OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of line-code-violation-propagated
|
|
on CPRI link."
|
|
::= { coiCpriRoeStatsEntry 13 }
|
|
|
|
coiCpriRoeErroredLengthFrames OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object gives the number of RoE errored-length-frames value."
|
|
::= { coiCpriRoeStatsEntry 14 }
|
|
|
|
-- MIB Conformance Statements
|
|
|
|
ciscoCpriMIBConformance OBJECT IDENTIFIER
|
|
::= { ciscoCpriMIB 2 }
|
|
|
|
ciscoCpriMIBCompliances OBJECT IDENTIFIER
|
|
::= { ciscoCpriMIBConformance 1 }
|
|
|
|
ciscoCpriMIBGroups OBJECT IDENTIFIER
|
|
::= { ciscoCpriMIBConformance 2 }
|
|
|
|
|
|
END
|
|
|
|
|