-- ***************************************************************** -- CISCO-CPRI-MIB.my -- CPRI INTERFACE MIB -- -- September 2020, Rajarshi Chakraborty (rajarcha) -- -- Copyright (c) 2020 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-CPRI-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Counter32, Unsigned32, Counter64 FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, DisplayString, MacAddress, TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex, ifName FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoCpriMIB MODULE-IDENTITY LAST-UPDATED "202009100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-@cisco.com" DESCRIPTION "This MIB module defines the managed objects for physical layer characteristics of cpri interfaces and performance statistics objects for protocol specific counters in falidae devices. Glossary: TX : Transmit RX : Receive " REVISION "202009100000Z" DESCRIPTION "Initial version of the MIB module." ::= { ciscoMgmt 9999 } -- Textual Conventions definition will be defined before this line -- MIB Notification Definitions ciscoCpriMIBNotifs OBJECT IDENTIFIER ::= { ciscoCpriMIB 0 } -- MIB Object Definitions ciscoCpriMIBObjects OBJECT IDENTIFIER ::= { ciscoCpriMIB 1 } coiCpriController OBJECT IDENTIFIER ::= { ciscoCpriMIBObjects 1 } coiCpriRoeStats OBJECT IDENTIFIER ::= { ciscoCpriMIBObjects 2 } coiCpriControllerTable OBJECT-TYPE SYNTAX SEQUENCE OF CoiCpriControllerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides management information for cpri layer related attributes of interfaces with an ifType of cpri" ::= { coiCpriController 1 } coiCpriControllerEntry OBJECT-TYPE SYNTAX CoiCpriControllerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information on cpri layer related attributes of interfaces with an ifType cpri. Entries are created by the feature when a new interface is added. Entries are deleted by the agent when an interface is removed." INDEX { ifIndex } ::= { coiCpriControllerTable 1 } CoiCpriControllerEntry ::= SEQUENCE { coiCpriControllerSupportedRateList BITS, coiCpriControllerConfiguredRateList BITS, coiCpriControllerNegotiatedRate INTEGER, coiCpriControllerPortRole INTEGER, coiCpriControllerL1StartupTimer Unsigned32, coiCpriControllerAdminStatus INTEGER, coiCpriControllerOperStatus INTEGER, coiCpriControllerLoopbackInfo INTEGER, coiCpriControllerAlarmStatus BITS } coiCpriControllerSupportedRateList OBJECT-TYPE SYNTAX BITS { rate614Mbps(0), rate1228Mbps(1), rate2457Mbps(2), rate3072Mbps(3), rate4915Mbps(4), rate6144Mbps(5), rate9830Mbps(6), rate8110Mbps(7), rate10137Mbps(8), rate12165Mbps(9), rate24330Mbps(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the current supported rate list of the cpri controller, valid values are : rate614Mbps(0): CPRI option 1 - 614 Mbps rate1228Mbps(1): CPRI option 2 - 1228 Mbps rate2457Mbps(2): CPRI option 3 - 2457 Mbps rate3072Mbps(3): CPRI option 4 - 3072 Mbps rate4915Mbps(4): CPRI option 5 - 4915 Mbps rate6144Mbps(5): CPRI option 6 - 6144 Mbps rate9830Mbps(6): CPRI option 7 - 9830 Mbps rate8110Mbps(7): CPRI option 7A - 8110 Mbps rate10137Mbps(8): CPRI option 8 - 10137 Mbps rate12165Mbps(9): CPRI option 9 - 12165 Mbps rate24330Mbps(10): CPRI option 10 - 24330 Mbps " ::= { coiCpriControllerEntry 1 } coiCpriControllerConfiguredRateList OBJECT-TYPE SYNTAX BITS { rate614Mbps(0), rate1228Mbps(1), rate2457Mbps(2), rate3072Mbps(3), rate4915Mbps(4), rate6144Mbps(5), rate9830Mbps(6), rate8110Mbps(7), rate10137Mbps(8), rate12165Mbps(9), rate24330Mbps(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the current configured rate list of the cpri controller. Maximum 4 values can be configured at a time on a port. Valid values are : rate614Mbps(0): CPRI option 1 - 614 Mbps rate1228Mbps(1): CPRI option 2 - 1228 Mbps rate2457Mbps(2): CPRI option 3 - 2457 Mbps rate3072Mbps(3): CPRI option 4 - 3072 Mbps rate4915Mbps(4): CPRI option 5 - 4915 Mbps rate6144Mbps(5): CPRI option 6 - 6144 Mbps rate9830Mbps(6): CPRI option 7 - 9830 Mbps rate8110Mbps(7): CPRI option 7A - 8110 Mbps rate10137Mbps(8): CPRI option 8 - 10137 Mbps rate12165Mbps(9): CPRI option 9 - 12165 Mbps rate24330Mbps(10): CPRI option 10 - 24330 Mbps " ::= { coiCpriControllerEntry 2 } coiCpriControllerNegotiatedRate OBJECT-TYPE SYNTAX INTEGER { rateNone(0), rate614Mbps(1), rate1228Mbps(2), rate2457Mbps(3), rate3072Mbps(4), rate4915Mbps(5), rate6144Mbps(6), rate9830Mbps(7), rate8110Mbps(8), rate10137Mbps(9), rate12165Mbps(10), rate24330Mbps(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the current negotiated rate of the cpri controller, valid values are - rateNone(0): No valid negotiated rate rate614Mbps(1): The negotiated rate is 614 Mbps rate1228Mbps(2): The negotiated rate is 1228 Mbps rate2457Mbps(3): The negotiated rate is 2457 Mbps rate3072Mbps(4): The negotiated rate is 3072 Mbps rate4915Mbps(5): The negotiated rate is 4915 Mbps rate6144Mbps(6): The negotiated rate is 6144 Mbps rate9830Mbps(7): The negotiated rate is 9830 Mbps rate8110Mbps(8): The negotiated rate is 8110 Mbps rate10137Mbps(9): The negotiated rate is 10137 Mbps rate12165Mbps(10): The negotiated rate is 12165 Mbps rate24330Mbps(11): The negotiated rate is 24330 Mbps " ::= { coiCpriControllerEntry 3 } coiCpriControllerPortRole OBJECT-TYPE SYNTAX INTEGER { slave(0), master(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the role of the cpri controller, valid values are - slave(0): The port mode is slave master(1): The port mode is master " ::= { coiCpriControllerEntry 4 } coiCpriControllerL1StartupTimer OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object is gives the L1 Startup Timer value of the cpri controller (in terms of milliseconds). " ::= { coiCpriControllerEntry 5 } coiCpriControllerAdminStatus OBJECT-TYPE SYNTAX INTEGER { down(0), up(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the administration status of the cpri interfaces. when it is set to down(0), it results in Tx being stopped and there should be corresponding change in coiCpriControllerOperStatus. Valid values are : down(0): The controller is in down state. up(1): The controller is in up state" ::= { coiCpriControllerEntry 6 } coiCpriControllerOperStatus OBJECT-TYPE SYNTAX INTEGER { down(0), up(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the current operational state of the cpri controller, valid values are - down(0): The controller is in down state. up(1): The controller is in up state. If coiCpriControllerAdminStatus is down(0) then coiCpriControllerOperStatus should be down(0). If coiCpriControllerAdminStatus is changed to up(1) then coiCpriControllerOperStatus should change to up(1), provided the controller is operational and ready to transmit traffic. It should remain in down(0) if there is a fault that prevents it from going to the up(1) state. " ::= { coiCpriControllerEntry 7 } coiCpriControllerLoopbackInfo OBJECT-TYPE SYNTAX INTEGER { loopbackNone(0), loopbackLine(1), loopbackInternal(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the loopback value of the cpri controller, valid values are - loopbackNone(0): No controller loopback info loopbackLine(1): The controller loopback info is line level loopbackInternal(2): The controller loopback info is internal level. " ::= { coiCpriControllerEntry 8 } coiCpriControllerAlarmStatus OBJECT-TYPE SYNTAX BITS { noAlarm(0), los(1), lof(2), rai(3), sdi(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current defect status of the cpri controller. Valid values are - noAlarm(0): No Alarm. This bit will be set when none of the following defect bits are set. los(1): LOS (Loss Of Signal). This bit will be set when LOS alarm condition is detected on the CPRI Rx side. lof(2): LOF (Loss Of Frame). This bit will be set when LOF alarm condition is detected on the CPRI Rx side. rai(3): RAI (Remote Alarm Indication). This bit will be set when RAI alarm condition reported in a control word. sdi(4): SDI (SAP Defect Indication). This bit will be set when SDI alarm condition reported in a control word." ::= { coiCpriControllerEntry 9 } coiCpriRoeStatsTable OBJECT IDENTIFIER ::= { coiCpriRoeStats 1 } coiCpriRoeStatsEntry OBJECT-TYPE SYNTAX CoiCpriRoeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing stas information on CPRI controller ROE port." INDEX { ifIndex } ::= { coiCpriRoeStatsTable 1 } CoiCpriRoeStatsEntry ::= SEQUENCE { coiCpriRoeRxFrames Counter64, coiCpriRoeDroppedFramesDetected Counter64, coiCpriRoeStrayFramesDetected Counter64, coiCpriRoeDuplicateFramesDetected Counter64, coiCpriRoeOutOfSeqFramesDetected Counter64, coiCpriRoeOutOfSeqFramesDropped Counter64, coiCpriRoeTxFrames Counter64, coiCpriRoeIdleFramesSent Counter64, coiCpriRoePktDelayVarMinVal Counter64, coiCpriRoePktDelayVarMaxVal Counter64, coiCpriRoePktDelayVarAvgVal Counter64, coiCpriRoeLineCodeViolationDetected Counter64, coiCpriRoeLineCodeViolationPropagated Counter64, coiCpriRoeErroredLengthFrames Counter64 } coiCpriRoeRxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE frames received." ::= { coiCpriRoeStatsEntry 1 } coiCpriRoeDroppedFramesDetected OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE frames dropped." ::= { coiCpriRoeStatsEntry 2 } coiCpriRoeStrayFramesDetected OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE stray frame detected." ::= { coiCpriRoeStatsEntry 3 } coiCpriRoeDuplicateFramesDetected OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE duplicate frame detected." ::= { coiCpriRoeStatsEntry 4 } coiCpriRoeOutOfSeqFramesDetected OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE out of sequence frame detected." ::= { coiCpriRoeStatsEntry 5 } coiCpriRoeOutOfSeqFramesDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE out of sequence frames dropped." ::= { coiCpriRoeStatsEntry 6 } coiCpriRoeTxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE frames transmitted." ::= { coiCpriRoeStatsEntry 7 } coiCpriRoeIdleFramesSent OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of idle frames sent." ::= { coiCpriRoeStatsEntry 8 } coiCpriRoePktDelayVarMinVal OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the RoE packet-delay-variation min value." ::= { coiCpriRoeStatsEntry 9 } coiCpriRoePktDelayVarMaxVal OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the RoE packet-delay-variation max value." ::= { coiCpriRoeStatsEntry 10 } coiCpriRoePktDelayVarAvgVal OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the RoE packet-delay-variation avg value." ::= { coiCpriRoeStatsEntry 11 } coiCpriRoeLineCodeViolationDetected OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of line-code-violation-detected on CPRI link." ::= { coiCpriRoeStatsEntry 12 } coiCpriRoeLineCodeViolationPropagated OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of line-code-violation-propagated on CPRI link." ::= { coiCpriRoeStatsEntry 13 } coiCpriRoeErroredLengthFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the number of RoE errored-length-frames value." ::= { coiCpriRoeStatsEntry 14 } -- MIB Conformance Statements ciscoCpriMIBConformance OBJECT IDENTIFIER ::= { ciscoCpriMIB 2 } ciscoCpriMIBCompliances OBJECT IDENTIFIER ::= { ciscoCpriMIBConformance 1 } ciscoCpriMIBGroups OBJECT IDENTIFIER ::= { ciscoCpriMIBConformance 2 } END