WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/hp/LJ2025-MIB

2607 lines
102 KiB
Plaintext
Raw Permalink Blame History

-- (C) COPYRIGHT HEWLETT-PACKARD COMPANY 2015.
--
-- LaserJet 2025 Printer Model Specific MIB.
--
-- Generated on Jan. 26, 2015.
--
-- Company names and product names mentioned herein may be
-- trademarks, and/or registered trademarks of their respective
-- companies.
--
-- For internal and external use.
--
-- This MIB describes all the printer model specific
-- objects supported by the LaserJet 2025 printer
-- when networked connected.
--
-- The following MIBs also contain objects supported
-- by a LaserJet 2025 printer:
--
-- IEEE 802.11 MIB
-- IEEE 802.1X MIB
-- rfc 2790 Host Resources MIB
-- rfc 3411 SNMP Framework MIB
-- rfc 3412 SNMP MPD MIB
-- rfc 3418 SNMP MIB
-- rfc 3805 Printer MIB
-- rfc 4022 TCP MIB
-- rfc 4293 IP MIB
-- rfc 4113 UDP MIB
-- PWG 5107.1-2005 Printer Port Monitor MIB
--
-- This MIB complies with the following RFCs:
--
-- rfc 1157 Simple Network Management Protocol
-- rfc 2578 Structure of Management Information Version 2
--
-- Notes:
--
-- 1) Objects containing a string which are defined in this MIB use the
-- first two bytes to hold the symbol set used to encode the string.
-- The Roman-8 symbol set has a hex encoding of 0x0115. Other
-- symbol sets are listed in the PCL 5 Comparison Guide in table
-- C-1 Symbol Set Values.
--
-- 2) Some of the objects included are only supported if an accessory
-- is installed. These accessories include:
-- MIO based accessories
-- SIMM based accessories
-- Paper handling accessories
LJ2025-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE
FROM RFC-1212
DisplayString
FROM SNMPv2-TC;
hpPrintServer OBJECT IDENTIFIER ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) 11}
dm OBJECT IDENTIFIER ::= { hpPrintServer nm(2) hpsystem(3) net-peripheral(9) netdm(4) 2}
device OBJECT IDENTIFIER ::= { dm 1 }
system OBJECT IDENTIFIER ::= { device 1 }
settings-system OBJECT IDENTIFIER ::= { system 1 }
destination-subsystem OBJECT IDENTIFIER ::= { device 4 }
print-engine OBJECT IDENTIFIER ::= { destination-subsystem 1 }
settings-prt-eng OBJECT IDENTIFIER ::= { print-engine 1 }
marking-agent-density OBJECT IDENTIFIER ::= { settings-prt-eng 9 }
status-prt-eng OBJECT IDENTIFIER ::= { print-engine 2 }
marking-agent OBJECT IDENTIFIER ::= { print-engine 5 }
settings-marking-agent OBJECT IDENTIFIER ::= { marking-agent 1 }
print-engine-test OBJECT IDENTIFIER ::= { print-engine 9 }
hrm OBJECT IDENTIFIER ::= { dm 3 }
hrStorage OBJECT IDENTIFIER ::= { hrm 2 }
hrStorageTable OBJECT IDENTIFIER ::= { hrStorage 3 }
hrStorageEntry OBJECT IDENTIFIER ::= { hrStorageTable 1 }
hrDevice OBJECT IDENTIFIER ::= { hrm 3 }
hrDeviceTable OBJECT IDENTIFIER ::= { hrDevice 2 }
hrDeviceEntry OBJECT IDENTIFIER ::= { hrDeviceTable 1 }
hrPrinterTable OBJECT IDENTIFIER ::= { hrDevice 5 }
hrPrinterEntry OBJECT IDENTIFIER ::= { hrPrinterTable 1 }
org OBJECT IDENTIFIER ::= { iso 3 }
dod OBJECT IDENTIFIER ::= { org 6 }
internet OBJECT IDENTIFIER ::= { dod 1 }
private OBJECT IDENTIFIER ::= { internet 4 }
enterprises OBJECT IDENTIFIER ::= { private 1 }
nm OBJECT IDENTIFIER ::= { hpPrintServer 2 }
interface OBJECT IDENTIFIER ::= { nm 4 }
npCard OBJECT IDENTIFIER ::= { interface 3 }
snmpAccess OBJECT IDENTIFIER ::= { nm 15 }
community OBJECT IDENTIFIER ::= { snmpAccess 1 }
npSys OBJECT IDENTIFIER ::= { npCard 1 }
npConns OBJECT IDENTIFIER ::= { npCard 4 }
npCfg OBJECT IDENTIFIER ::= { npCard 5 }
npCtl OBJECT IDENTIFIER ::= { npCard 7 }
npPort OBJECT IDENTIFIER ::= { npCard 13 }
npDhcp OBJECT IDENTIFIER ::= { npCard 16 }
system OBJECT IDENTIFIER ::= { nm 3 }
netPeripheral OBJECT IDENTIFIER ::= { system 9 }
netPrinter OBJECT IDENTIFIER ::= { netPeripheral 1 }
generalDeviceStatus OBJECT IDENTIFIER ::= { netPrinter 1 }
npNpi OBJECT IDENTIFIER ::= { npCard 8 }
npNpiPeripheralAttributeEntry OBJECT IDENTIFIER ::= { npNpi 3 }
npNpiCardAttributeEntry OBJECT IDENTIFIER ::= { npNpi 4 }
gdStatusEntry OBJECT IDENTIFIER ::= { generalDeviceStatus 2 }
device-configure OBJECT IDENTIFIER ::= { settings-system 32 }
source-subsystem OBJECT IDENTIFIER ::= { device 2 }
io OBJECT IDENTIFIER ::= { source-subsystem 1 }
settings-io OBJECT IDENTIFIER ::= { io 1 }
processing-subsystem OBJECT IDENTIFIER ::= { device 3 }
pdl OBJECT IDENTIFIER ::= { processing-subsystem 3 }
settings-pdl OBJECT IDENTIFIER ::= { pdl 1 }
pdl-pcl OBJECT IDENTIFIER ::= { pdl 3 }
pdl-postscript OBJECT IDENTIFIER ::= { pdl 4 }
pdl-pclxl OBJECT IDENTIFIER ::= { pdl 16 }
pjl OBJECT IDENTIFIER ::= { processing-subsystem 5 }
intray OBJECT IDENTIFIER ::= { print-engine 3 }
settings-intray OBJECT IDENTIFIER ::= { intray 1 }
intrays OBJECT IDENTIFIER ::= { intray 3 }
intray1 OBJECT IDENTIFIER ::= { intrays 1 }
intray2 OBJECT IDENTIFIER ::= { intrays 2 }
intray3 OBJECT IDENTIFIER ::= { intrays 3 }
imaging OBJECT IDENTIFIER ::= { print-engine 6 }
print-media OBJECT IDENTIFIER ::= { print-engine 8 }
settings-print-media OBJECT IDENTIFIER ::= { print-media 1 }
media-info OBJECT IDENTIFIER ::= { print-media 3 }
media1 OBJECT IDENTIFIER ::= { media-info 1 }
media2 OBJECT IDENTIFIER ::= { media-info 2 }
media3 OBJECT IDENTIFIER ::= { media-info 3 }
media4 OBJECT IDENTIFIER ::= { media-info 4 }
media5 OBJECT IDENTIFIER ::= { media-info 5 }
media6 OBJECT IDENTIFIER ::= { media-info 6 }
media7 OBJECT IDENTIFIER ::= { media-info 7 }
media8 OBJECT IDENTIFIER ::= { media-info 8 }
media9 OBJECT IDENTIFIER ::= { media-info 9 }
media10 OBJECT IDENTIFIER ::= { media-info 10 }
media11 OBJECT IDENTIFIER ::= { media-info 11 }
media12 OBJECT IDENTIFIER ::= { media-info 12 }
media13 OBJECT IDENTIFIER ::= { media-info 13 }
media14 OBJECT IDENTIFIER ::= { media-info 14 }
media15 OBJECT IDENTIFIER ::= { media-info 15 }
media16 OBJECT IDENTIFIER ::= { media-info 16 }
media17 OBJECT IDENTIFIER ::= { media-info 17 }
media18 OBJECT IDENTIFIER ::= { media-info 18 }
media19 OBJECT IDENTIFIER ::= { media-info 19 }
media20 OBJECT IDENTIFIER ::= { media-info 20 }
media21 OBJECT IDENTIFIER ::= { media-info 21 }
media22 OBJECT IDENTIFIER ::= { media-info 22 }
media23 OBJECT IDENTIFIER ::= { media-info 23 }
media24 OBJECT IDENTIFIER ::= { media-info 24 }
media25 OBJECT IDENTIFIER ::= { media-info 25 }
media26 OBJECT IDENTIFIER ::= { media-info 26 }
media27 OBJECT IDENTIFIER ::= { media-info 27 }
media28 OBJECT IDENTIFIER ::= { media-info 28 }
media29 OBJECT IDENTIFIER ::= { media-info 29 }
media30 OBJECT IDENTIFIER ::= { media-info 30 }
media31 OBJECT IDENTIFIER ::= { media-info 31 }
media-modes OBJECT IDENTIFIER ::= { print-media 4 }
consumables OBJECT IDENTIFIER ::= { print-engine 10 }
mono-color-switching-mode OBJECT-TYPE
SYNTAX INTEGER {
eNeverSwitch(1),
eAlwaysSwitch(2),
eLookAheadSwitch(3)
}
ACCESS read-write
STATUS optional
DESCRIPTION "This object allows the user to view/change the color/mono
switching mode for a device.
Additional information:
This object allows the user to view/change the color/mono
switching mode for a device."
::= { settings-system 31 }
calibration-power-on-initiation OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2),
eDelayed(3)
}
ACCESS read-write
STATUS optional
DESCRIPTION "This object determines when a power on calibration occurs. If
eOn, then the calibration occurs immediately following boot. If
eOff, then it never occurs. If eDelayed, then refer to the
CALIBRATION-POWER-ON-DELAY PML object for the delay interval."
::= { settings-prt-eng 20 }
calibration-power-on-delay OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "This is the delay interval for the power on calibration in
minutes. This PML object is only used if the
CALIBRATION-POWER-ON-INITIATION PML object is set to eDelayed.
Additional information:
This is the delay interval for the power on
calibration in minutes. The range in minutes for the product
is 1-60 minutes. "
::= { settings-prt-eng 21 }
calibration-pages-printed-initiation OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The number of pages that will be printed prior to an
automatically initiated print calibration. If set to 0, it
turns this calibration off.
Additional information:
This is the number of pages that will be printed
prior to an automatically initiated print calibration.
If set to 0, it turns this calibration off. The range for
the product will be 0-500. On Raptor the default value is
200. On Kiwi the default value is 150"
::= { settings-prt-eng 22 }
calibration-timer-initiation OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "This is a timer in minutes that will be set in between
calibrations. When the timer expires, a calibration will
automatically be initiated. If set to 0, it turns this
calibration off.
Additional information:
This is a timer in minutes that will be set in
between calibrations. If set to 0,
it turns this calibration off. The range for the product
will be 0-10080. When you set to a value of 2 (min) or any
other legal value other than 0, the device does not
immediately begin calibrating when the timer expires.
The calibration takes place after the timer expires,
the next job has finished printing, and a 15 minute period
of inactivity has passed."
::= { settings-prt-eng 23 }
calibration-cpr-pages-printed-initiation OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The number of pages that will be printed prior to an
automatically initiated CPR calibration. If set to 0, it turns
this calibration off.
Additional information:
The number of pages that will be printed prior to an
automatically initiated CPR calibration. If set to 0, it turns
this calibration off."
::= { settings-prt-eng 32 }
total-mono-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of black pages printed by the device.
Additional information:
Total number of mono pages printed by the device."
::= { status-prt-eng 6 }
total-color-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of color pages printed by the device.
Additional information:
Total number of color pages printed
by the device."
::= { status-prt-eng 7 }
marker-density-calibration OBJECT-TYPE
SYNTAX INTEGER {
eNotCallibrating(1),
eCalibrateALL(2),
eCalibrateColor(3),
eCalibrateColorPlaneRegistration(5)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns the calibration status or triggers a calibration cycle.
All calibration procedures are used if set to eCalibrateALL. If
set to eCalibrateColor then a full density engine calibration
is triggered. If set to eCalibrateHalftone, then a Halftone
calibration is triggered. If set to
eCalibrateColorPlaneRegistration, then a Color Plane
Registration calibration is triggered. If set to
eCalibrateDrumPhaseAdjustment, then a Drum Phase Adjustment
calibration is triggered.If set to eCalibrateLowSpeedColor,
then a Low Speed Color calibration is triggered.If set to
eCalibrateDrumSpeedAdjustment, then a Drum Speed Adjustment
calibration is triggered.If set to eCalibrateNeutrals, then a
Gray Axis Control calibration is triggered.
Additional information:
Returns the calibration status or triggers a
calibration cycle."
::= { settings-marking-agent 11 }
pe-test-abort-calibration OBJECT-TYPE
SYNTAX INTEGER {
eFalse(1),
eTrue(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Aborts all executing and scheduled calibrations if set to
eTrue.
Additional information:
All scheduled caliberations will abort. Any currently
executing calibration will finish normally."
::= { print-engine-test 94 }
setCommunityName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS current
DESCRIPTION "This object controls access of snmp read-write requests. Factory
default configuration provides authentication of incoming packets
with community names: internal and public. This object overrides the
factory default settings so that the factory default setttings no longer
work. This object returns SET or NOT_SET."
::= { community 1 }
getCommunityName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS current
DESCRIPTION "This object controls access of snmp read requests. Factory
default configuration provides authentication of incoming packets
with community names: internal and public. This object provides
access in addition to the factory default settings. If
set, then authentication will succeed with any of the following
community names: internal, public, getCommunityName, or
setCommunityName. This object returns SET or NOT_SET."
::= { community 2 }
npSysStatusMessage OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS current
DESCRIPTION "A status string reflecting the current state of the card
and peripheral."
::= { npSys 2 }
npSysModelNumber OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION "The HP model number of the device."
::= { npSys 10 }
npSysNetworkConnectors OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This object describes the network connectors supported by the
device. The value is a bit mask. A set bit indicates the
connector is supported.
Bit Value Connector
0 0x01 Ethernet, BNC
1 0x02 Ethernet, AUI
2 0x04 Ethernet, RJ-45
3 0x08 TokenRing, DB-9
4 0x10 TokenRing, RJ-45
5 0x20 LocalTalk
6 0x40 100VG, RJ-45
7 0x80 100T, RJ-45"
::= { npSys 11 }
npSysCardServices1 OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This object is a bitmap showing what services are available
on the card.
Bit 0 - IPX/SPX/NCP protocol stack
Bit 1 - IP/TCP protocol stack
Bit 2 - LLC/DLC protocol stack
Bit 3 - Ethertalk protocol stack
Bit 4 - IPv6 protocol stack
Bit 5 - IPSec protocol stack
Bits 6 - 11 Reserved
Bit 12 - LPD print services
Bit 13 - FTP print services
Bit 14 - Port 9100 print services
Bit 15 - IPP print services
Bits 16 - 23 Reserved
Bit 24 - Queue Server Bindery
Bit 25 - Queue Server NDS
Bit 26 - Remote Printer
Bit 27 - SPX Direct Mode
Bit 28 - DLC Print Services
Bit 29 - EtherTalk Print Services
Bits 30 - 31 Reserved"
::= { npSys 16 }
npSysCardServices2 OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This object is a bitmap showing what services are available
on the card.
Bit 0 - XIP2
Bit 1 - PML Get/Set
Bit 2 - PML Traps
Bit 3 - Scan to Web Browser
Bit 4 - Scan to Email
Bit 5 - MFP Scan Support
Bits 6 - 11 Reserved
Bit 12 - Telnet API
Bit 13 - Web API
Bit 14 - SNMP V2
Bit 15 - SNMP Traps
Bit 16 - Download
Bit 17 - TFTP
Bit 18 - RCFG
Bit 19 - SLP
Bit 20 - Syslog
Bit 21 - DHCP
Bit 22 - BOOTP
Bit 23 - RARP
Bit 24 - SNMP V3
Bit 25 - SSL Functionality
Bit 26 - Auto IP
Bits 27 - 31 Reserved"
::= { npSys 17 }
npSysCardServices3 OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This object is a bitmap showing what services are available
on the card.
Bit 0 - 100T
Bit 1 - Token Ring 802.5
Bit 2 - 802.11b
Bit 3 - 80211.a
Bit 4 - Bluetooth
Bits 5 - 11 Reserved
Bit 12 - EIO. For embedded Jetdirect this bit will be 1.
Bit 13 - LIO
Bit 14 - USB
Bit 15 - Firewire
Bit 16 - TCP Download
Bits 17 - 31 Reserved"
::= { npSys 22 }
npConnsIP OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS current
DESCRIPTION "Remote IP address of the node currently connected to the card.
Zero if no connection is active."
::= { npConns 11 }
npCfgSource OBJECT-TYPE
SYNTAX INTEGER {manual-one(1),
bootp-two(2),
manual-three(3),
bootp-four(4),
dhcp(5),
not-configured(6),
default-config(7),
rarp(8),
read-only(9),
auto-ip(10)}
ACCESS read-write
STATUS current
DESCRIPTION "This object indicates how the device obtained its IP configuration."
::= { npCfg 1 }
npCfgYiaddr OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS current
DESCRIPTION "The IP address assigned to the card from the BOOTP reply
yiaddr field."
::= { npCfg 2 }
npCfgSubnetMask OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS current
DESCRIPTION "The subnet mask associated with the IP address of this card."
::= { npCfg 12 }
npCfgDefaultGateway OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS current
DESCRIPTION "This variable contains the IP address of the default router for this
card."
::= { npCfg 13 }
npCfgDomainName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS current
DESCRIPTION "The print server domain name."
::= { npCfg 16 }
npCfgWINSNameServerIdPri OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS current
DESCRIPTION "Primary name server for NetBIOS over TCP/IP."
::= { npCfg 22 }
npCfgPasswd1Verify OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS current
DESCRIPTION "Compares string value to passwd1 and returns OK if match,
GENERAL ERROR if doesn't match."
::= { npCfg 28 }
npCfgPasswd1 OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS current
DESCRIPTION "Password for root or administrator. Get request returns
either 'SET' or 'NOT_SET'."
::= { npCfg 29 }
npCfgLinkType OBJECT-TYPE
SYNTAX INTEGER {autoNegotiate(1),
full10T(2),
half10T(3),
full100T(4),
half100T(5),
auto100T(6),
full1000T(7)}
ACCESS read-write
STATUS current
DESCRIPTION "Network link speed and communication mode."
::= { npCfg 35 }
npCfgBonjourDomainName OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION "The name used as the 'target name' in the DNS SRV records by
Multicast Domain Name System (Bonjour)."
::= { npCfg 46 }
npCtlReconfig OBJECT-TYPE
SYNTAX Integer32
ACCESS read-write
STATUS current
DESCRIPTION "Writing any value to this variable causes the card to
reconfigure itself by doing the BOOTP/TFTP configuration
activity."
::= { npCtl 8 }
npCtlProtocolSet OBJECT-TYPE
SYNTAX Integer32
ACCESS read-write
STATUS current
DESCRIPTION "This is a 4 byte integer value. The least significant bytes
represent the protocols on the card. A value of '1' indicates
a protocol that is enabled. A value of '0' indicates a
protocol that is disabled.
The 32-bit protocol enable 'structure' is defined as:
bits 31-28: Number of I/O channels/protocols present (NUM_CHAN)
bits 27-24: Number of I/O channels which may operate concurrently
(NUM_OP_CHAN)
bits 23-16: unused, reserved
bits 15-1: Individual I/O channel/protocol enable bits,
0 == disable, 1 == enable
MIO_IOCHAN_NOVELL bit 1
MIO_IOCHAN_LLC bit 2
MIO_IOCHAN_TCP bit 3
MIO_IOCHAN_ATALK bit 4
MIO_IOCHAN_IPV6 bit 5
bit 0: When NUM_OP_CHAN == 1, auto-protocol select enable bit,
0 == disable, 1 == enable (APS_ON)"
::= { npCtl 9 }
npCtlSnmpVersionAccess OBJECT-TYPE
SYNTAX INTEGER {snmpV1RW-snmpV3RW(1),
snmpV1RO-snmpV3RW(2),
snmpV1NoAccess-snmpV3RW(3),
snmpV1RW-snmpV3NoAccess(4),
snmpV1RO-snmpV3NoAccess(5)}
ACCESS read-write
STATUS current
DESCRIPTION "Manages an SNMP version's read and write access to the MIB."
::= { npCtl 27 }
npCtlBonjour OBJECT-TYPE
SYNTAX Integer32 (0..1)
ACCESS read-write
STATUS current
DESCRIPTION "Configure Multicast Domain Name Service.
(0) = Bonjour disabled
(1) = Bonjour enabled"
::= { npCtl 29 }
npPortNumPorts OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "The number of peripheral interfaces supported by this device."
::= { npPort 1 }
npDHCPserver OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-only
STATUS current
DESCRIPTION "IP address of DHCP server that provided this unit with an IP
address via the DHCP protocol."
::= { npDhcp 2 }
gdStatusBytes OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "The number of valid bytes in the gdStatusEntry
array."
::= { generalDeviceStatus 1 }
gdStatusDisplay OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS current
DESCRIPTION "The string diplayed on the peripheral front panel.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this is always a zero length string."
::= { generalDeviceStatus 3 }
gdStatusId OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS current
DESCRIPTION "A formatted string of NVT ASCII
charactersdescribing this peripheral."
::= { generalDeviceStatus 7 }
gdStatusJobTimeout OBJECT-TYPE
SYNTAX Integer32
ACCESS read-write
STATUS obsolete
::= { generalDeviceStatus 10 }
gdPasswords OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS current
DESCRIPTION "This object is used as a 256 byte NVRAM area for JetAdmin. It
is completely managed by JetAdmin. Initially it is initialized
to all zeros. A coldboot will re-initialize to all zeros."
::= { generalDeviceStatus 13 }
npNpiPaeClass OBJECT-TYPE
SYNTAX INTEGER {printer(1),
plotter(2),
xStation(3)}
ACCESS read-only
STATUS current
DESCRIPTION "The class assigned to the peripheral onto which
this card is plugged."
::= { npNpiPeripheralAttributeEntry 2 }
npNpiPaeIdentification OBJECT-TYPE
SYNTAX INTEGER {laserjet-IIISI(1),
laserjet-4SI(5)}
ACCESS read-only
STATUS current
DESCRIPTION "The Identification number of the peripheral. These values are
defined in the MIO spec. DesignJet, PaintJet XL300, and
DesignJet/600 peripherals will identify themselves as
LaserJet-IIIsi."
::= { npNpiPeripheralAttributeEntry 3 }
npNpiCaeClass OBJECT-TYPE
SYNTAX INTEGER {rs-232(1),
centronics(2),
csma-cd-network(3),
token-ring-network(4),
scsi(5),
hpib(6),
localtalk(7),
hpna(8),
usb(9),
firewire(10),
bluetooth(11),
ieee802-11b(12)}
ACCESS read-only
STATUS current
DESCRIPTION "The class of this network peripheral card."
::= { npNpiCardAttributeEntry 2 }
gdStatusLineState OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This describes the line state of the peripheral.
When non-zero, the peripheral is off-line. When
zero the peripheral is on-line."
::= { gdStatusEntry 1 }
gdStatusPaperState OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This describes the state of the paper on the peripheral.
When non-zero, the peripheral has a paper problem. When
zero, the peripheral does not have a paper problem."
::= { gdStatusEntry 2 }
gdStatusInterventionState OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This describes the intervention state of the
peripheral. When non-zero, the peripheral requires
human intervention to continue working. When
zero, it requires no assistance."
::= { gdStatusEntry 3 }
gdStatusPeripheralError OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This is the error code from the peripheral."
::= { gdStatusEntry 6 }
gdStatusPaperOut OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral is out of paper.
off (0),
paper-out-or-paper-mount (1),
manual-paper-feed-needed (2)
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 8 }
gdStatusPaperJam OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral has a paper jam.
off (0),
paper-jam(1)
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 9 }
gdStatusTonerLow OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral has a low toner condition.
off (0),
toner-low (1),
no-toner-cartridge (2)
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 10 }
gdStatusPagePunt OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral did not receive data fast
enough to keep up with the print engine when generating a page.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 11 }
gdStatusMemoryOut OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral did not have enough memory
to render an image on a page.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 12 }
gdStatusIoActive OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral is processing data from
this I/O interface card. For some peripherals, such as the
HP LaserJet IIISi printer or HP DesignJet plotter,
this value is always a zero (0).
For X.20.06 firmware and later firmware releases, this object is
not relevant. In order not to break legacy applications which call this
object in multi-varbind requests, this value is always zero (0)."
::= { gdStatusEntry 13 }
gdStatusBusy OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral is busy processing
print/plot data.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 14 }
gdStatusWait OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral is waiting for print/plot
data to process.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 15 }
gdStatusInitialize OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral is initializing or
warming up.
off (0),
initializing (1),
warm-up(2)
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 16 }
gdStatusDoorOpen OBJECT-TYPE
SYNTAX Integer32 (0..255)
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral cover or door is open.
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 17 }
gdStatusPrinting OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral is printing or otherwise
marking or moving paper.
off (0),
ordinary-page (1),
test-fonts-config-or-start-page (2)
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 18 }
gdStatusPaperOutput OBJECT-TYPE
SYNTAX Integer32
ACCESS read-only
STATUS current
DESCRIPTION "This indicates that the peripheral has a paper output problem
such as the output storage bin being full.
off (0),
output-storage-full (1)
For some peripherals, such as the HP LaserJet IIISi printer
or HP DesignJet plotter, this value is always a zero (0)."
::= { gdStatusEntry 19 }
energy-star OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION "Returns or changes the Energy Star sleep value. If the value
is greater than zero, then the device will go into energy
saving sleep mode after the print engine has been idle for the
number of seconds specified by this object. A value of zero
means Energy Star is disabled and the device will not go to
sleep based on print engine idle time. The value must be
non-negative.
Additional information:
The product will always be in
sleep mode when not processing data. This object will
always return a value of 1."
::= { settings-system 1 }
sleep-mode OBJECT-TYPE
SYNTAX INTEGER {
eFalse(1),
eTrue(2)
}
ACCESS read-only
STATUS optional
DESCRIPTION "Returns eTrue if the device is in energy saving sleep mode,
otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes
the device to wake up, if it is in sleep mode. Setting
SLEEP-MODE to eTrue causes the device to go into sleep mode.
Additional information:
The product will always be in
sleep mode except when either processing a print job or
in an error state."
::= { settings-system 2 }
service-password OBJECT-TYPE
SYNTAX INTEGER
ACCESS write-only
STATUS optional
DESCRIPTION "When set to the password value, other service related objects
become 'visible' (i.e readable) or become writable. When
written with any other value, the service related objects
become 'hidden' (i.e. are no longer readable) or are not longer
writable. The objects that can be effected by the
SERVICE-PASSWORD object include: SERIAL-NUMBER and
TOTAL-ENGINE-PAGE-COUNT. The password value, and the list of
objects effected by the SERVICE-PASSWORD being set to the
correct value, should be documented in the device POS.
Additional information:
The objects that can be effected by the SERVICE-
PASSWORD are: SCANNER-JAM-PAGE-COUNT, SCANNER-ADF-PAGE
-COUNT, SCAN-ADF-PAGE-COUNT, SCANNER-RETRIEVE-SCANLINE,
SCANNER-MOTOR-CONTROL, COPIER-ADF-PAGE-COUNT, COPIER-
PRINT-PAGE-COUNT, TOTAL-ENGINE-PAGE-COUNT, PRINT-ENGINE-
JAM-COUNT, PRINT-ENGINE-MISPICK-COUNT, CLEAR-NVRAM"
::= { settings-system 9 }
device-configure-custom-product-number OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "This object allows manufacturing to change the product number
to a pre-defined alternate after release. This feature will
allow manufacturing to assign unique product numbers to custom
product bundles when the device is unable to determine its
product number in firmware. For example, A HP Color LaserJet
CP1515n could be configured to display CP1516n to the customer.
This product number must be defined prior to release.
Additional information:
This object allows manufacturing to change the product number
to a pre-defined alternate after release. This feature will
allow manufacturing to assign unique product numbers to custom
product bundles when the device is unable to determine its
product number in firmware. For example, A HP Color LaserJet
CP1515n could be configured to display CP1516n to the customer.
This product number must be defined prior to release."
::= { device-configure 19 }
control-panel-button-press-delay OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "This object gives the number of seconds to wait before
simulating the button press when CONTROL-PANEL-BUTTON-PRESS is
next called.
Additional information:
This object gives the number of seconds to wait before
simulating the button press when CONTROL-PANEL-BUTTON-PRESS is
next called."
::= { settings-system 47 }
low-power OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the Auto Low Power sleep value. The device
will go into energy saving Auto Low Power mode after the print
engine has been idle for the number of seconds specified by
this object. Frida supports values of 300 until 14400 seconds.
If the value is invalid then it will return status of
PML_Status_ErrUnsupValue and will not issue command to the
engine.
Additional information:
Returns or changes the Auto Low Power sleep value. The device
will go into energy saving Auto Low Power mode after the print
engine has been idle for the number of seconds specified by
this object. The product supports values of 0 (Off), 60 (1
minute), 900 (15 minutes), 1800 (30 minutes), 3600 (1 hour),
7200 (2 hours), and 14400 (4 hours).
If the value is invalid then it will return a status of
PML_ERROR_INVALID_OR_UNSUPPORTED_VALUE and will not issue
a command to the engine."
::= { settings-system 49 }
control-panel-display-contrast OBJECT-TYPE
SYNTAX INTEGER {
eLightest(1),
eLight(2),
eMedium(3),
eDark(4),
eDarkest(5)
}
ACCESS read-write
STATUS optional
DESCRIPTION "This object returns or sets the display contrast setting if the
control panel has a display and it supports contrast
adjustment. The setting Is stored in NVRAM, so the value is
saved over power cycles.
Additional information:
This object returns or sets the display contrast setting
if the control panel has a display and it supports
contrast adjustment. The setting is stored in NVRAM,
so the value is saved over power cycles."
::= { settings-system 73 }
io-timeout OBJECT-TYPE
SYNTAX INTEGER(5..7200)
ACCESS read-write
STATUS optional
DESCRIPTION "The amount of time, in seconds, to wait for more print job data
to be received before an I/O timeout occurs. The I/O channel
being timed is the I/O channel that received the data
associated with the current print job. If an I/O timeout
occurs, the PDL processing sub-system assumes all the data
associated with the current print job has been received, and
processes the end of job in a PDL specific manner. The POS
specifies the supported values.
Additional information:
If an I/O timeout occurs,the PDL processing
sub-system will consider it an end of job condition only
if there is data from another I/O subsystem waiting to be
processed.
The supported values are 5 to 7200 seconds. Setting to a
value outside the supported range returns
<badValue> status."
::= { settings-io 1 }
io-switch OBJECT-TYPE
SYNTAX INTEGER {
eYes(1)
}
ACCESS read-only
STATUS optional
DESCRIPTION "Indicates if the device will switch between I/O channels when a
job boundary is encountered and print job data is available on
another I/O channel."
::= { settings-io 2 }
default-copies OBJECT-TYPE
SYNTAX INTEGER(1..999)
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes default copies. Default copies is the
default values used by the PDL to control the number of copies
of each page in the print job that are printed. The print job
can override this value. The list of supported values should be
documented in the device POS.
Additional information:
The supported values are 1 through 999.
Setting to an unsupported value causes the printer to
substitute in a snap value and to return
<noError> status.
The snaps are as follows:
<1 snaps to
>999 snaps to 999"
::= { settings-pdl 4 }
default-vertical-black-resolution OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the value of the default vertical black
resolution. The units are dots per inch.
Additional information:
In the product, changing this OID
also causes DEFAULT-HORIZONTAL-BLACK RESOLUTION to
change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and
DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the
same. The supported values are 600, and 1200.
When the default monochrome resolution or bits-per-pixel
are changed to anything other than 600x1 the product
no longer prints color jobs. Color jobs are always 600x1.
Setting to an unsupported value causes the printer to
substitute in a snap value and to return
<noError> status.
The snap values are as follows:
<450 will snap to 600
>=450 and <900 will snap to 600
>=900 will snap to 1200"
::= { settings-pdl 8 }
default-horizontal-black-resolution OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the value of the default horizontal black
resolution. The units are dots per inch.
Additional information:
In the product, changing this OID
also causes DEFAULT-VERTICAL-BLACK RESOLUTION to change.
DEFAULT-HORIZONTAL-BLACK-RESOLUTION and
DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the
same. The supported values are 600 and 1200. When the default
monochrome resolution or bits-per-pixel are changed to
anything other than 600x1 the product no longer prints color
jobs. Color jobs are always 600x1.
Setting to an unsupported value causes the printer to
substitute in a snap value and to return
<noError> status.
The snap values are as follows:
<450 snaps to 600
>=450 and <900 snaps to 600
>=900 snaps to 1200"
::= { settings-pdl 9 }
default-lines-per-page OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the default number of lines per page. The
POS indicates the supported values. An unsupported value causes
the printer to use the closest supported value, causing the
printer to return the <noError>.
Additional information:
The supported values in the product
are 5 to 128. Setting to an unsupported value
causes the printer to substitute in a snap value and to
return <noError> status.
The snap values are as follows:
<5 snaps to 5
>128 snaps to 128"
::= { settings-pdl 11 }
default-vmi OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the default vertical motion index. The unit
of measure for VMI is centipoints per line. The POS indicates
the supported values. An unsupported value causes the printer
to use the closest supported value, causing the printer to
return <noError>.
Additional information:
Setting this object may cause
DEFAULT-LINES-PER-PAGE to change."
::= { settings-pdl 12 }
default-media-size OBJECT-TYPE
SYNTAX INTEGER {
eUSExecutive(1),
eUSLetter(2),
eUSLegal(3),
eFoolscap(10),
eROC16K(17),
eISOandJISA4(26),
eISOandJISA5(25),
eROC16K195X270(34),
eJISB5(45),
eISOB5(65),
eJapanesePostcardSingle(71),
eJapanesePostcardDouble(72),
eMonarch(80),
eCommercial10(81),
eROC16K184X260(89),
eInternationalDL(90),
eInternationalC5(91),
eInternationalB5(100),
eCustom(101)
}
ACCESS read-write
STATUS optional
DESCRIPTION "This indicates the default media size. A write of an
unsupported value causes an <ErrorInvalidOrUnsupported Value>. Complete list of supported media sizes along with their
dimensions are listed in the ''Media Size Table'' near the end
of this document. (for a full list of media size enums see the
end of this file) "
::= { settings-pdl 13 }
cold-reset-media-size OBJECT-TYPE
SYNTAX INTEGER {
eUSLetter(2),
eISOandJISA4(26)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or sets the media size that is used as the
DEFAULT-MEDIA-SIZE when a cold reset occurs."
::= { settings-pdl 19 }
default-media-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or sets the media name that is used until the media
name is changed by a print job command.
Additional information:
This string must be one of the MEDIAn-NAME
objects, except it cannot be set to ANY.
The value of this object is saved across
a power cycle."
::= { settings-pdl 22 }
reprint OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2),
eAuto(3)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the reprint (jam recovery) setting. If eOn,
then the device will reprint pages jammed pages. If eOff, the
device will not attempt to reprint jammed pages. If eAuto, a
device dependent algorithm (which should be documented in the
POS) will be used to determine if the page gets reprinted. This
object controls all PDLs, unless a specific PDL supports its
own reprint control mechanism. To date, only PostScript has a
PDL reprint control mechanism.
Additional information:
Setting this object when the printer is not
idle, may cause a status of <noError> to be returned, but
the new value will not take effect until a job boundary
is reached. If a get is done on object before the job
boundary is reached, the value last set will be
returned.
When the value is set to eOff, pages will not be stored
in the printer, and in the event of a paper jam, will
have to be reprinted. When the value is set to eOn,
pages will be stored until delivery, therefore, in the
event of a paper jam, the page will be reprinted.
When the value is set to eAuto, the printer will behave
as though it is eOff when there is less than seven
megabytes of memory installed in the printer. When
additional memory is installed, to total at least seven
megabytes of RAM, the setting of eAuto will behave as
though it was set to eOn."
::= { settings-pdl 36 }
wide-a4 OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the wide A4 logical page size setting. If
eOn, then the margins/printable area of A4 paper will be
changed to allow 80 10-pitch characters to be printed on a
single line. If eOff then the industry standard A4 logical page
size is used."
::= { settings-pdl 37 }
dark-courier OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the dark Courier setting. If eOn, then the
Courier font used will approximate the same darkness as the
LaserJet III printer. If eOff, then the Courier font used will
approximate the same darkness as the LaserJet 4 printer."
::= { settings-pdl 38 }
default-bits-per-pixel OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Controls the number of levels used (per pixel) when printing
grayscale or color images."
::= { settings-pdl 39 }
pcl-total-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of PCL pages printed by the device."
::= { pdl-pcl 5 }
pcl-default-font-height OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the default PCL height. Height is an
approximate measure of the body of the type in centipoints. A
centipoint is 1/7200 inch. Height applies only to proportional
fonts. Point size, in points, can be converted to font height,
in centipoints, by multiplying the point size by 100. The POS
indicates the supported values. An unsupported value causes the
printer to use the closest supported value, causing the printer
to return <noError>. ''Closest'' means
the smallest absolute difference.
Additional information:
This object refers to the font point size
with 400 representing the smallest settable font (4) and
99975 representing the largest settable font (999.75).
The default of 1200 is a font point size of 12.
Supported values range from 400 to 99975. Setting to an
unsupported value causes the printer to substitute in a
snap value and to return
<noError> status.
The snap values are as follows:
<=400 snaps to 400
>=99975 snaps to 99975
Fonts are settable to the nearest quarter point size
(i.e. 10, 10.25, 10.50, 10.75). Unsupported values in
the range 401 to 99974 snap DOWN to the previous
supported value (i.e 25293 snaps to 25275 or 75038 snaps
to 75025)."
::= { pdl-pcl 13 }
pcl-default-font-source OBJECT-TYPE
SYNTAX INTEGER {
eInternal(1),
ePermanentSoft(2),
eRomSimm1(10)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the value of the default font source
variable in NVRAM."
::= { pdl-pcl 14 }
pcl-default-font-number OBJECT-TYPE
SYNTAX INTEGER(0..255)
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the value of the default font number
variable in NVRAM. Writing an unsupported value causes the
printer to generate an <badValue>.
Additional information:
Valid numbers or 0 - 255, but only font
numbers that are included in the PCL FONT LIST are
selectable."
::= { pdl-pcl 15 }
pcl-default-font-width OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the default PCL font width. Width is
expressed as the width of a character in centipoints. A
centipoint is 1/7200 inch. Width applies only to fixed space
fonts. Pitch, in character per inch, can be converted to font
width, in centipoints, by dividing 7200 by the pitch. The POS
indicates the supported values. An unsupported value causes the
printer to use the closest supported value, causing the printer
to return <noError>. ''Closest'' means
the smallest absolute difference.
Additional information:
Setting to an unsupported value causes the
printer to substitue in a snap value (listed below) and
return <noError> status.
The snap values for pitch are as follow:
<=44 snaps to 44
>=9999 snaps to 9999
Unsupported values in the range 44 - 9999 (.44 - 99.99)
snap DOWN to the next supported value."
::= { pdl-pcl 16 }
postscript-total-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of PostScript pages printed by the device."
::= { pdl-postscript 5 }
postscript-print-errors OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the value of the print PostScript errors
setting. If eOn, PostScript prints an error page showing the
error encountered and the stack at the time of the error.
Additional information:
Returns or changes the value of the print PostScript errors
setting. If eOn, PostScript prints an error page showing the
error encountered and the stack at the time of the error."
::= { pdl-postscript 11 }
pclxl-total-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of PCLXL pages printed by the device."
::= { pdl-pclxl 1 }
pjl-password OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION "Returns PJL password, if the password is not set (zero). If the
password is set, then attempting to retrieve the password
causes an <genErr> to occur and will return
the <NullValue>."
::= { pjl 1 }
print-density OBJECT-TYPE
SYNTAX INTEGER(1..5)
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or sets the print density setting. Print density is the
instantaneous amount of marking agent applied to the paper
while printing. A value of zero has the lowest print density,
yielding a lighter page. A value of 10 has the highest print
density, yielding a darker page. Each POS should document what
values in the 0 to 10 range are supported.
Additional information:
When this value is written, the page
pipeline will be flushed (all pages being printed are
completed, no new ones are started), the new density
setting is set and printing resumes. The acutal change
in print density may be gradual over several pages.
The supported values are 1 through 5. Setting to an
unsupported value causes the printer to substitue in a
a snap value and to return <noError>
status.
The snap values are as follows:
<1 snaps to 1
>5 snaps to 5."
::= { settings-prt-eng 5 }
invalid-personality-reports-enabled OBJECT-TYPE
SYNTAX INTEGER {
eDisabled(1),
eEnabled(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Read or configure wether invalid personality reports are
enabled or disabled for a product."
::= { settings-prt-eng 18 }
total-engine-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of pages printed by the device. POS indicates if
the total engine page count is kept in NVRAM, and the maximum
supported value before the page count rolls over to zero.
Additional information:
This object is stored in NVRAM. The maximum value of
this count is 1000000 before it rolls over to zero."
::= { status-prt-eng 5 }
print-engine-jam-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of pages jammed in the print engine's life time.
The POS indicates if the total jam count is kept in NVRAM and
the maximum supported value before the jam count rolls over to
zero.
Additional information:
This object is stored in NVRAM. The maximum value of
this count is 65000 before it rolls over to zero."
::= { status-prt-eng 34 }
print-engine-mispick-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of pages mispicked in the print engine's life
time. The POS indicates if the total mispick count is kept in
NVRAM and the maximum supported value before the mispick count
rolls over to zero.
Additional information:
This object is stored in NVRAM. The maximum value of
this count is 65000 before it rolls over to zero."
::= { status-prt-eng 35 }
supply-out-device-state OBJECT-TYPE
SYNTAX INTEGER {
eNoSupplyOut(1),
eOffline(2),
eSupplyOutOverride(3),
eMonochromePrintingAfterColorCartridgeOut(4)
}
ACCESS read-only
STATUS optional
DESCRIPTION "This PML object indicates the current behavior of the device if
one or more supplies have reached out. If no supply has reached
out, the value of this PML object is eNoSupplyOut. If one or
more supplies have reached out, the value of this PML object
will indicate if the printer is online and if so what mode is
being used to continue printing.
Additional information:
This PML object indicates the current behavior of the device if
one or more supplies have reached out. If no supply has reached
out, the value of this PML object is eNoSupplyOut. If one or
more supplies have reached out, the value of this PML object
will indicate if the printer is online and if so what mode is
being used to continue printing. If the printer is in both
eSupplyOutOverride and eMonochromePrintingAfterColorCartridgeOut
then eMonochromePrintingAfterColorCartridgeOut will be returned."
::= { status-prt-eng 49 }
duplex-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "Total number of sheets of media that have been duplex printed.
A sheet is counted if it travels through the duplex page path,
regardless of whether or not marks are made on the page. The
POS will indicate if the value is kept in NVRAM.
Additional information:
Total number of sheets of media that have been duplex printed.
A sheet is counted if it travels through the duplex page path,
regardless of whether or not marks are made on the page.
This object is stored in NVRAM. The maximum value of
this count is 65000 before it rolls over to zero."
::= { status-prt-eng 22 }
print-engine-revision OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Print engine revision string.
Additional information:
Print engine revision string."
::= { status-prt-eng 26 }
custom-paper-dim-unit OBJECT-TYPE
SYNTAX INTEGER {
eTenThousandthsOfInches(3),
eMicrometers(4)
}
ACCESS read-write
STATUS optional
DESCRIPTION "The units of measure used to specify the width and height of
the printer's custom paper. The unit of measure of
eTenThousandthsOfInches is 0.0001 inches.
Additional information:
The only valid values for this object are
eTenThousandthsOfInches (3), and eMicrometers (4). The
data for this object is stored in NVRAM."
::= { settings-intray 7 }
custom-paper-feed-dim OBJECT-TYPE
SYNTAX INTEGER(50000..140000)
ACCESS read-write
STATUS optional
DESCRIPTION "Sets the printer's custom paper dimension in the feed direction
(direction parallel to the direction of paper feeding). The
value for this object is specified in micrometers or
tenthousandths of an inch, depending upon the value of
CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and
should be documented in the POS for each product.
Additional information:
The valid range is 50000 to 140000 if
CUSTOM-PAPER_DIM_UNIT is eTenThousandthsOfInches or 127000 to
355600 if CUSTOM-PAPER-DIM-UNIT is ePmicrometers. Attempts
to set this object outside the valid range will result in a
return value of ERROR_INVALID_OR_UNSUPPORTED_VALUE."
::= { settings-intray 8 }
custom-paper-xfeed-dim OBJECT-TYPE
SYNTAX INTEGER(30000..85000)
ACCESS read-write
STATUS optional
DESCRIPTION "Sets the printer's custom paper dimension in the cross-feed
direction (direction ninety degrees relative to the direction
of paper feeding). The value for this object is specified in
micrometers or tenthousandths of an inch, depending upon the
value of CUSTOM-PAPER-DIM-UNIT. The valid range is
engine-dependent and should be documented in the POS for each
product.
Additional information:
The valid range for the product
is 30000 to 85000 if CUSTOM-PAPER-DIM-UNIT is
eTenThousandthsOfInches or 76200 to 215900 if
CUSTOM-PAPER-DIM-UNIT is ePmicrometers. Attempts to set
this object outside the valid range will result in a
return value of <badValue>."
::= { settings-intray 9 }
tray1-media-size-loaded OBJECT-TYPE
SYNTAX INTEGER {
eUSExecutive(1),
eUSLetter(2),
eUSLegal(3),
eFoolscap(10),
eROC16K(17),
eISOandJISA6(24),
eISOandJISA5(25),
eISOandJISA4(26),
eROC16K195X270(34),
eJISB5(45),
eJapansePostcardSingle(71),
eJapansePostcardDouble(72),
eIndexCard5x8(75),
ePhoto4x6(76),
eMonarch(80),
eCommercial10(81),
eROC16K184X260(89),
eInternationalDL(90),
eInternationalC5(91),
eInternationalB5(100),
eCustom(101),
ePhoto10x15(118),
eAnySize(32765)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns the media size that is currently configuredconfigured
in tray #1. This object can be set to indicate the media size
currently loaded, if the printer supports input trays that can
not sense the media size. Complete list of supported media
sizes along with their dimensions are listed in the ''Media
Size Table'' near the end of this document."
::= { intray1 1 }
tray2-media-size-loaded OBJECT-TYPE
SYNTAX INTEGER {
eUSExecutive(1),
eUSLetter(2),
eUSLegal(3),
eFoolscap(10),
eROC16K(17),
eISOandJISA6(24),
eISOandJISA5(25),
eISOandJISA4(26),
eROC16K195X270(34),
eJISB5(45),
eJapansePostcardSingle(71),
eJapansePostcardDouble(72),
eIndexCard5x8(75),
ePhoto4x6(76),
eMonarch(80),
eCommercial10(81),
eROC16K184X260(89),
eInternationalDL(90),
eInternationalC5(91),
eInternationalB5(100),
eCustom(101),
ePhoto10x15(118),
eAnySize(32765)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns the media size that is currently configured in tray #2.
Complete list of supported media sizes along with their
dimensions are listed in the ''Media Size Table'' near the end
of this document."
::= { intray2 1 }
tray3-media-size-loaded OBJECT-TYPE
SYNTAX INTEGER {
eUSExecutive(1),
eUSLetter(2),
eUSLegal(3),
eFoolscap(10),
eROC16K(17),
eISOandJISA6(24),
eISOandJISA5(25),
eISOandJISA4(26),
eROC16K195X270(34),
eJISB5(45),
eJapansePostcardSingle(71),
eJapansePostcardDouble(72),
eIndexCard5x8(75),
ePhoto4x6(76),
eMonarch(80),
eCommercial10(81),
eROC16K184X260(89),
eInternationalDL(90),
eInternationalC5(91),
eInternationalB5(100),
eCustom(101),
ePhoto10x15(118),
eAnySize(32765)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns the media size that is currently configured in tray #3.
Complete list of supported media sizes along with their
dimensions are listed in the ''Media Size Table'' near the end
of this document."
::= { intray3 1 }
default-ret OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eLight(2),
eMedium(3),
eDark(4)
}
ACCESS read-write
STATUS optional
DESCRIPTION "Returns or changes the Resolution Enhancement Technology
setting. Devices that only support eOff and eOn should map all
other values to eOn and always return the same non-eOff value
to indicatep on. The list of supported values should be
documented in the device POS."
::= { imaging 5 }
media-names-available OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "The value of this object controls which of the MEDIAx-NAME
objects are supported. If a bit is set to zero, then attempting
to get or set the corresponding MEDIAx-NAME objects will return
<noSuchName>.
Additional information:
Since this object is read-only, the corresponding MEDIAx
objects will always be available. The DEFAULTS below
represent which MediaNameX is available on this product
of the total possible available defined in SYNTAX, so the
collection is like a bitfield. Raptor does not support
cMediaName32Available"
::= { settings-print-media 1 }
media1-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 1 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media1 1 }
media1-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
The engine processing characteristics that are to
be applied to this media type. Currently, 'engine
processing characteristics' denotes changes to
fusing temperature and/or transfer roller voltage."
::= { media1 4 }
media2-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 2 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media2 1 }
media2-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media2 4 }
media3-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 3 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media3 1 }
media3-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media3 4 }
media4-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 4 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media4 1 }
media4-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media4 4 }
media5-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 5 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media5 1 }
media5-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE.
Raptor will havea default value of 4"
::= { media5 4 }
media6-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 6 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media6 1 }
media6-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 5.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media6 4 }
media7-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 7 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media7 1 }
media7-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 5.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media7 4 }
media8-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 8 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media8 1 }
media8-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 6.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media8 4 }
media9-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 9 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media9 1 }
media9-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 7.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media9 4 }
media10-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 10 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media10 1 }
media10-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media10 4 }
media11-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 11 name.
Additional information:
The symbol set for this string is Roman-8."
::= { media11 1 }
media11-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 8.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media11 4 }
media12-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 12 name.
Additional information:
Raptor will have a default value of 'Light'.
The symbol set for this string is Roman-8."
::= { media12 1 }
media12-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 2.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media12 4 }
media13-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 13 name.
Additional information:
Raptor will have a default value of 'Mid Weight'
The symbol set for this string is Roman-8."
::= { media13 1 }
media13-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 3
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media13 4 }
media14-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 14 name.
Additional information:
Raptor will have a default value of 'Heavy'
The symbol set for this string is Roman-8."
::= { media14 1 }
media14-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 4
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media14 4 }
media15-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 15 name.
Additional information:
Raptor will have a default value of 'Extra Heavy'
The symbol set for this string is Roman-8."
::= { media15 1 }
media15-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 5
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media15 4 }
media16-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 16 name.
Additional information:
Raptor will have a default value of 'Heavy Gloss'
The symbol set for this string is Roman-8."
::= { media16 1 }
media16-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 6
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media16 4 }
media17-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 17 name.
Additional information:
Raptor will have a default value of 'Extra Heavy Gloss'
The symbol set for this string is Roman-8."
::= { media17 1 }
media17-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 7
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media17 4 }
media18-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 18 name.
Additional information:
Raptor will have a default value of 'Card Glossy'
The symbol set for this string is Roman-8."
::= { media18 1 }
media18-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 8.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media18 4 }
media19-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 19 name.
Additional information:
Raptor will have a default value of 'Transparency'
The symbol set for this string is Roman-8."
::= { media19 1 }
media19-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 10
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media19 4 }
media20-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 20 name.
Additional information:
Raptor will have a default value of 'Labels'
The symbol set for this string is Roman-8."
::= { media20 1 }
media20-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 11
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media20 4 }
media21-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 21 name.
Additional information:
Raptor will have a default value of 'Letterhead'
The symbol set for this string is Roman-8."
::= { media21 1 }
media21-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 1.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media21 4 }
media22-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 22 name.
Additional information:
Raptor will have a default value of 'Envelope'
The symbol set for this string is Roman-8."
::= { media22 1 }
media22-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 12.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media22 4 }
media23-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 23 name.
Additional information:
Raptor will have a default value of 'Heavy Envelope'
The symbol set for this string is Roman-8."
::= { media23 1 }
media23-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 13
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media23 4 }
media24-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 24 name.
Additional information:
Raptor will have a default value of 'Preprinted'
The symbol set for this string is Roman-8."
::= { media24 1 }
media24-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 1
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media24 4 }
media25-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 25 name.
Additional information:
Raptor will have a default value of 'Prepunched'
The symbol set for this string is Roman-8."
::= { media25 1 }
media25-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 1
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media25 4 }
media26-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 26 name.
Additional information:
Raptor will have a default value of 'Color'
The symbol set for this string is Roman-8."
::= { media26 1 }
media26-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media26 4 }
media27-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 27 name.
Additional information:
Raptor will have a default value of 'Bond'
The symbol set for this string is Roman-8."
::= { media27 1 }
media27-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 3
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media27 4 }
media28-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 28 name.
Additional information:
Raptor will have a default value of 'Recycled'
The symbol set for this string is Roman-8."
::= { media28 1 }
media28-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media28 4 }
media29-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 29 name.
Additional information:
Raptor will have a default value of 'Rough'
The symbol set for this string is Roman-8."
::= { media29 1 }
media29-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media29 4 }
media30-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 30 name.
Additional information:
Raptor will have a default value of 'Heavy Rough'
The symbol set for this string is Roman-8."
::= { media30 1 }
media30-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 5.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media30 4 }
media31-name OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "Media 31 name.
Additional information:
Raptor will have a default value of 'HP Tough Paper'.
The symbol set for this string is Roman-8."
::= { media31 1 }
media31-engine-media-mode OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION "The engine processing characteristics that are to be applied to
this media. The processing characteristics are device
specific.
Additional information:
Raptor will have a default value of 14.
See the description for MEDIA1-ENGINE-MEDIA-MODE."
::= { media31 4 }
engine-media-modes-supported1 OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION "The list of engine media modes supported by the device. The
modes are each separated by a comma character. An example
string would be: 'Normal,Rough,Low,Vellum'.
Additional information:
The list of engine media modes supported by the device. The
modes are each separated by a comma character. An example
string would be: 'Normal,Rough,Low,Vellum'. Raptor does not support
'Photo2' but supports 'Extra Heavy'"
::= { media-modes 1 }
pe-test-cause-assert OBJECT-TYPE
SYNTAX INTEGER {
e49DEAD(1),
e494C02(2)
}
ACCESS write-only
STATUS optional
DESCRIPTION "This object allows the user to cause a 49 Error.
Additional information:
This object allows the user to cause a 49 Error."
::= { print-engine-test 111 }
pe-test-cause-79error OBJECT-TYPE
SYNTAX INTEGER {
e79DEAD(1)
}
ACCESS write-only
STATUS optional
DESCRIPTION "This object allows the user to cause a 79 Error.
Additional information:
This object allows the user to cause a 79 Error."
::= { print-engine-test 116 }
consumable-reorder-url OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..64))
ACCESS read-write
STATUS optional
DESCRIPTION "This object is used to read and write the URL that can be used
to reorder consumables for this device. This URL is set at the
factory but can be updated by a reseller or third party.
Additional information:
The URL can be up to 64 characters long."
::= { consumables 2 }
END
View Git Blame Copy Permalink