-- (C) COPYRIGHT HEWLETT-PACKARD COMPANY 2015. -- -- LaserJet 2025 Printer Model Specific MIB. -- -- Generated on Jan. 26, 2015. -- -- Company names and product names mentioned herein may be -- trademarks, and/or registered trademarks of their respective -- companies. -- -- For internal and external use. -- -- This MIB describes all the printer model specific -- objects supported by the LaserJet 2025 printer -- when networked connected. -- -- The following MIBs also contain objects supported -- by a LaserJet 2025 printer: -- -- IEEE 802.11 MIB -- IEEE 802.1X MIB -- rfc 2790 Host Resources MIB -- rfc 3411 SNMP Framework MIB -- rfc 3412 SNMP MPD MIB -- rfc 3418 SNMP MIB -- rfc 3805 Printer MIB -- rfc 4022 TCP MIB -- rfc 4293 IP MIB -- rfc 4113 UDP MIB -- PWG 5107.1-2005 Printer Port Monitor MIB -- -- This MIB complies with the following RFCs: -- -- rfc 1157 Simple Network Management Protocol -- rfc 2578 Structure of Management Information Version 2 -- -- Notes: -- -- 1) Objects containing a string which are defined in this MIB use the -- first two bytes to hold the symbol set used to encode the string. -- The Roman-8 symbol set has a hex encoding of 0x0115. Other -- symbol sets are listed in the PCL 5 Comparison Guide in table -- C-1 Symbol Set Values. -- -- 2) Some of the objects included are only supported if an accessory -- is installed. These accessories include: -- MIO based accessories -- SIMM based accessories -- Paper handling accessories LJ2025-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE FROM RFC-1212 DisplayString FROM SNMPv2-TC; hpPrintServer OBJECT IDENTIFIER ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) 11} dm OBJECT IDENTIFIER ::= { hpPrintServer nm(2) hpsystem(3) net-peripheral(9) netdm(4) 2} device OBJECT IDENTIFIER ::= { dm 1 } system OBJECT IDENTIFIER ::= { device 1 } settings-system OBJECT IDENTIFIER ::= { system 1 } destination-subsystem OBJECT IDENTIFIER ::= { device 4 } print-engine OBJECT IDENTIFIER ::= { destination-subsystem 1 } settings-prt-eng OBJECT IDENTIFIER ::= { print-engine 1 } marking-agent-density OBJECT IDENTIFIER ::= { settings-prt-eng 9 } status-prt-eng OBJECT IDENTIFIER ::= { print-engine 2 } marking-agent OBJECT IDENTIFIER ::= { print-engine 5 } settings-marking-agent OBJECT IDENTIFIER ::= { marking-agent 1 } print-engine-test OBJECT IDENTIFIER ::= { print-engine 9 } hrm OBJECT IDENTIFIER ::= { dm 3 } hrStorage OBJECT IDENTIFIER ::= { hrm 2 } hrStorageTable OBJECT IDENTIFIER ::= { hrStorage 3 } hrStorageEntry OBJECT IDENTIFIER ::= { hrStorageTable 1 } hrDevice OBJECT IDENTIFIER ::= { hrm 3 } hrDeviceTable OBJECT IDENTIFIER ::= { hrDevice 2 } hrDeviceEntry OBJECT IDENTIFIER ::= { hrDeviceTable 1 } hrPrinterTable OBJECT IDENTIFIER ::= { hrDevice 5 } hrPrinterEntry OBJECT IDENTIFIER ::= { hrPrinterTable 1 } org OBJECT IDENTIFIER ::= { iso 3 } dod OBJECT IDENTIFIER ::= { org 6 } internet OBJECT IDENTIFIER ::= { dod 1 } private OBJECT IDENTIFIER ::= { internet 4 } enterprises OBJECT IDENTIFIER ::= { private 1 } nm OBJECT IDENTIFIER ::= { hpPrintServer 2 } interface OBJECT IDENTIFIER ::= { nm 4 } npCard OBJECT IDENTIFIER ::= { interface 3 } snmpAccess OBJECT IDENTIFIER ::= { nm 15 } community OBJECT IDENTIFIER ::= { snmpAccess 1 } npSys OBJECT IDENTIFIER ::= { npCard 1 } npConns OBJECT IDENTIFIER ::= { npCard 4 } npCfg OBJECT IDENTIFIER ::= { npCard 5 } npCtl OBJECT IDENTIFIER ::= { npCard 7 } npPort OBJECT IDENTIFIER ::= { npCard 13 } npDhcp OBJECT IDENTIFIER ::= { npCard 16 } system OBJECT IDENTIFIER ::= { nm 3 } netPeripheral OBJECT IDENTIFIER ::= { system 9 } netPrinter OBJECT IDENTIFIER ::= { netPeripheral 1 } generalDeviceStatus OBJECT IDENTIFIER ::= { netPrinter 1 } npNpi OBJECT IDENTIFIER ::= { npCard 8 } npNpiPeripheralAttributeEntry OBJECT IDENTIFIER ::= { npNpi 3 } npNpiCardAttributeEntry OBJECT IDENTIFIER ::= { npNpi 4 } gdStatusEntry OBJECT IDENTIFIER ::= { generalDeviceStatus 2 } device-configure OBJECT IDENTIFIER ::= { settings-system 32 } source-subsystem OBJECT IDENTIFIER ::= { device 2 } io OBJECT IDENTIFIER ::= { source-subsystem 1 } settings-io OBJECT IDENTIFIER ::= { io 1 } processing-subsystem OBJECT IDENTIFIER ::= { device 3 } pdl OBJECT IDENTIFIER ::= { processing-subsystem 3 } settings-pdl OBJECT IDENTIFIER ::= { pdl 1 } pdl-pcl OBJECT IDENTIFIER ::= { pdl 3 } pdl-postscript OBJECT IDENTIFIER ::= { pdl 4 } pdl-pclxl OBJECT IDENTIFIER ::= { pdl 16 } pjl OBJECT IDENTIFIER ::= { processing-subsystem 5 } intray OBJECT IDENTIFIER ::= { print-engine 3 } settings-intray OBJECT IDENTIFIER ::= { intray 1 } intrays OBJECT IDENTIFIER ::= { intray 3 } intray1 OBJECT IDENTIFIER ::= { intrays 1 } intray2 OBJECT IDENTIFIER ::= { intrays 2 } intray3 OBJECT IDENTIFIER ::= { intrays 3 } imaging OBJECT IDENTIFIER ::= { print-engine 6 } print-media OBJECT IDENTIFIER ::= { print-engine 8 } settings-print-media OBJECT IDENTIFIER ::= { print-media 1 } media-info OBJECT IDENTIFIER ::= { print-media 3 } media1 OBJECT IDENTIFIER ::= { media-info 1 } media2 OBJECT IDENTIFIER ::= { media-info 2 } media3 OBJECT IDENTIFIER ::= { media-info 3 } media4 OBJECT IDENTIFIER ::= { media-info 4 } media5 OBJECT IDENTIFIER ::= { media-info 5 } media6 OBJECT IDENTIFIER ::= { media-info 6 } media7 OBJECT IDENTIFIER ::= { media-info 7 } media8 OBJECT IDENTIFIER ::= { media-info 8 } media9 OBJECT IDENTIFIER ::= { media-info 9 } media10 OBJECT IDENTIFIER ::= { media-info 10 } media11 OBJECT IDENTIFIER ::= { media-info 11 } media12 OBJECT IDENTIFIER ::= { media-info 12 } media13 OBJECT IDENTIFIER ::= { media-info 13 } media14 OBJECT IDENTIFIER ::= { media-info 14 } media15 OBJECT IDENTIFIER ::= { media-info 15 } media16 OBJECT IDENTIFIER ::= { media-info 16 } media17 OBJECT IDENTIFIER ::= { media-info 17 } media18 OBJECT IDENTIFIER ::= { media-info 18 } media19 OBJECT IDENTIFIER ::= { media-info 19 } media20 OBJECT IDENTIFIER ::= { media-info 20 } media21 OBJECT IDENTIFIER ::= { media-info 21 } media22 OBJECT IDENTIFIER ::= { media-info 22 } media23 OBJECT IDENTIFIER ::= { media-info 23 } media24 OBJECT IDENTIFIER ::= { media-info 24 } media25 OBJECT IDENTIFIER ::= { media-info 25 } media26 OBJECT IDENTIFIER ::= { media-info 26 } media27 OBJECT IDENTIFIER ::= { media-info 27 } media28 OBJECT IDENTIFIER ::= { media-info 28 } media29 OBJECT IDENTIFIER ::= { media-info 29 } media30 OBJECT IDENTIFIER ::= { media-info 30 } media31 OBJECT IDENTIFIER ::= { media-info 31 } media-modes OBJECT IDENTIFIER ::= { print-media 4 } consumables OBJECT IDENTIFIER ::= { print-engine 10 } mono-color-switching-mode OBJECT-TYPE SYNTAX INTEGER { eNeverSwitch(1), eAlwaysSwitch(2), eLookAheadSwitch(3) } ACCESS read-write STATUS optional DESCRIPTION "This object allows the user to view/change the color/mono switching mode for a device. Additional information: This object allows the user to view/change the color/mono switching mode for a device." ::= { settings-system 31 } calibration-power-on-initiation OBJECT-TYPE SYNTAX INTEGER { eOff(1), eOn(2), eDelayed(3) } ACCESS read-write STATUS optional DESCRIPTION "This object determines when a power on calibration occurs. If eOn, then the calibration occurs immediately following boot. If eOff, then it never occurs. If eDelayed, then refer to the CALIBRATION-POWER-ON-DELAY PML object for the delay interval." ::= { settings-prt-eng 20 } calibration-power-on-delay OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This is the delay interval for the power on calibration in minutes. This PML object is only used if the CALIBRATION-POWER-ON-INITIATION PML object is set to eDelayed. Additional information: This is the delay interval for the power on calibration in minutes. The range in minutes for the product is 1-60 minutes. " ::= { settings-prt-eng 21 } calibration-pages-printed-initiation OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The number of pages that will be printed prior to an automatically initiated print calibration. If set to 0, it turns this calibration off. Additional information: This is the number of pages that will be printed prior to an automatically initiated print calibration. If set to 0, it turns this calibration off. The range for the product will be 0-500. On Raptor the default value is 200. On Kiwi the default value is 150" ::= { settings-prt-eng 22 } calibration-timer-initiation OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This is a timer in minutes that will be set in between calibrations. When the timer expires, a calibration will automatically be initiated. If set to 0, it turns this calibration off. Additional information: This is a timer in minutes that will be set in between calibrations. If set to 0, it turns this calibration off. The range for the product will be 0-10080. When you set to a value of 2 (min) or any other legal value other than 0, the device does not immediately begin calibrating when the timer expires. The calibration takes place after the timer expires, the next job has finished printing, and a 15 minute period of inactivity has passed." ::= { settings-prt-eng 23 } calibration-cpr-pages-printed-initiation OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The number of pages that will be printed prior to an automatically initiated CPR calibration. If set to 0, it turns this calibration off. Additional information: The number of pages that will be printed prior to an automatically initiated CPR calibration. If set to 0, it turns this calibration off." ::= { settings-prt-eng 32 } total-mono-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of black pages printed by the device. Additional information: Total number of mono pages printed by the device." ::= { status-prt-eng 6 } total-color-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of color pages printed by the device. Additional information: Total number of color pages printed by the device." ::= { status-prt-eng 7 } marker-density-calibration OBJECT-TYPE SYNTAX INTEGER { eNotCallibrating(1), eCalibrateALL(2), eCalibrateColor(3), eCalibrateColorPlaneRegistration(5) } ACCESS read-write STATUS optional DESCRIPTION "Returns the calibration status or triggers a calibration cycle. All calibration procedures are used if set to eCalibrateALL. If set to eCalibrateColor then a full density engine calibration is triggered. If set to eCalibrateHalftone, then a Halftone calibration is triggered. If set to eCalibrateColorPlaneRegistration, then a Color Plane Registration calibration is triggered. If set to eCalibrateDrumPhaseAdjustment, then a Drum Phase Adjustment calibration is triggered.If set to eCalibrateLowSpeedColor, then a Low Speed Color calibration is triggered.If set to eCalibrateDrumSpeedAdjustment, then a Drum Speed Adjustment calibration is triggered.If set to eCalibrateNeutrals, then a Gray Axis Control calibration is triggered. Additional information: Returns the calibration status or triggers a calibration cycle." ::= { settings-marking-agent 11 } pe-test-abort-calibration OBJECT-TYPE SYNTAX INTEGER { eFalse(1), eTrue(2) } ACCESS read-write STATUS optional DESCRIPTION "Aborts all executing and scheduled calibrations if set to eTrue. Additional information: All scheduled caliberations will abort. Any currently executing calibration will finish normally." ::= { print-engine-test 94 } setCommunityName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS current DESCRIPTION "This object controls access of snmp read-write requests. Factory default configuration provides authentication of incoming packets with community names: internal and public. This object overrides the factory default settings so that the factory default setttings no longer work. This object returns SET or NOT_SET." ::= { community 1 } getCommunityName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS current DESCRIPTION "This object controls access of snmp read requests. Factory default configuration provides authentication of incoming packets with community names: internal and public. This object provides access in addition to the factory default settings. If set, then authentication will succeed with any of the following community names: internal, public, getCommunityName, or setCommunityName. This object returns SET or NOT_SET." ::= { community 2 } npSysStatusMessage OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS current DESCRIPTION "A status string reflecting the current state of the card and peripheral." ::= { npSys 2 } npSysModelNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS current DESCRIPTION "The HP model number of the device." ::= { npSys 10 } npSysNetworkConnectors OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This object describes the network connectors supported by the device. The value is a bit mask. A set bit indicates the connector is supported. Bit Value Connector 0 0x01 Ethernet, BNC 1 0x02 Ethernet, AUI 2 0x04 Ethernet, RJ-45 3 0x08 TokenRing, DB-9 4 0x10 TokenRing, RJ-45 5 0x20 LocalTalk 6 0x40 100VG, RJ-45 7 0x80 100T, RJ-45" ::= { npSys 11 } npSysCardServices1 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This object is a bitmap showing what services are available on the card. Bit 0 - IPX/SPX/NCP protocol stack Bit 1 - IP/TCP protocol stack Bit 2 - LLC/DLC protocol stack Bit 3 - Ethertalk protocol stack Bit 4 - IPv6 protocol stack Bit 5 - IPSec protocol stack Bits 6 - 11 Reserved Bit 12 - LPD print services Bit 13 - FTP print services Bit 14 - Port 9100 print services Bit 15 - IPP print services Bits 16 - 23 Reserved Bit 24 - Queue Server Bindery Bit 25 - Queue Server NDS Bit 26 - Remote Printer Bit 27 - SPX Direct Mode Bit 28 - DLC Print Services Bit 29 - EtherTalk Print Services Bits 30 - 31 Reserved" ::= { npSys 16 } npSysCardServices2 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This object is a bitmap showing what services are available on the card. Bit 0 - XIP2 Bit 1 - PML Get/Set Bit 2 - PML Traps Bit 3 - Scan to Web Browser Bit 4 - Scan to Email Bit 5 - MFP Scan Support Bits 6 - 11 Reserved Bit 12 - Telnet API Bit 13 - Web API Bit 14 - SNMP V2 Bit 15 - SNMP Traps Bit 16 - Download Bit 17 - TFTP Bit 18 - RCFG Bit 19 - SLP Bit 20 - Syslog Bit 21 - DHCP Bit 22 - BOOTP Bit 23 - RARP Bit 24 - SNMP V3 Bit 25 - SSL Functionality Bit 26 - Auto IP Bits 27 - 31 Reserved" ::= { npSys 17 } npSysCardServices3 OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This object is a bitmap showing what services are available on the card. Bit 0 - 100T Bit 1 - Token Ring 802.5 Bit 2 - 802.11b Bit 3 - 80211.a Bit 4 - Bluetooth Bits 5 - 11 Reserved Bit 12 - EIO. For embedded Jetdirect this bit will be 1. Bit 13 - LIO Bit 14 - USB Bit 15 - Firewire Bit 16 - TCP Download Bits 17 - 31 Reserved" ::= { npSys 22 } npConnsIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS current DESCRIPTION "Remote IP address of the node currently connected to the card. Zero if no connection is active." ::= { npConns 11 } npCfgSource OBJECT-TYPE SYNTAX INTEGER {manual-one(1), bootp-two(2), manual-three(3), bootp-four(4), dhcp(5), not-configured(6), default-config(7), rarp(8), read-only(9), auto-ip(10)} ACCESS read-write STATUS current DESCRIPTION "This object indicates how the device obtained its IP configuration." ::= { npCfg 1 } npCfgYiaddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS current DESCRIPTION "The IP address assigned to the card from the BOOTP reply yiaddr field." ::= { npCfg 2 } npCfgSubnetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS current DESCRIPTION "The subnet mask associated with the IP address of this card." ::= { npCfg 12 } npCfgDefaultGateway OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS current DESCRIPTION "This variable contains the IP address of the default router for this card." ::= { npCfg 13 } npCfgDomainName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS current DESCRIPTION "The print server domain name." ::= { npCfg 16 } npCfgWINSNameServerIdPri OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS current DESCRIPTION "Primary name server for NetBIOS over TCP/IP." ::= { npCfg 22 } npCfgPasswd1Verify OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS current DESCRIPTION "Compares string value to passwd1 and returns OK if match, GENERAL ERROR if doesn't match." ::= { npCfg 28 } npCfgPasswd1 OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS current DESCRIPTION "Password for root or administrator. Get request returns either 'SET' or 'NOT_SET'." ::= { npCfg 29 } npCfgLinkType OBJECT-TYPE SYNTAX INTEGER {autoNegotiate(1), full10T(2), half10T(3), full100T(4), half100T(5), auto100T(6), full1000T(7)} ACCESS read-write STATUS current DESCRIPTION "Network link speed and communication mode." ::= { npCfg 35 } npCfgBonjourDomainName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS current DESCRIPTION "The name used as the 'target name' in the DNS SRV records by Multicast Domain Name System (Bonjour)." ::= { npCfg 46 } npCtlReconfig OBJECT-TYPE SYNTAX Integer32 ACCESS read-write STATUS current DESCRIPTION "Writing any value to this variable causes the card to reconfigure itself by doing the BOOTP/TFTP configuration activity." ::= { npCtl 8 } npCtlProtocolSet OBJECT-TYPE SYNTAX Integer32 ACCESS read-write STATUS current DESCRIPTION "This is a 4 byte integer value. The least significant bytes represent the protocols on the card. A value of '1' indicates a protocol that is enabled. A value of '0' indicates a protocol that is disabled. The 32-bit protocol enable 'structure' is defined as: bits 31-28: Number of I/O channels/protocols present (NUM_CHAN) bits 27-24: Number of I/O channels which may operate concurrently (NUM_OP_CHAN) bits 23-16: unused, reserved bits 15-1: Individual I/O channel/protocol enable bits, 0 == disable, 1 == enable MIO_IOCHAN_NOVELL bit 1 MIO_IOCHAN_LLC bit 2 MIO_IOCHAN_TCP bit 3 MIO_IOCHAN_ATALK bit 4 MIO_IOCHAN_IPV6 bit 5 bit 0: When NUM_OP_CHAN == 1, auto-protocol select enable bit, 0 == disable, 1 == enable (APS_ON)" ::= { npCtl 9 } npCtlSnmpVersionAccess OBJECT-TYPE SYNTAX INTEGER {snmpV1RW-snmpV3RW(1), snmpV1RO-snmpV3RW(2), snmpV1NoAccess-snmpV3RW(3), snmpV1RW-snmpV3NoAccess(4), snmpV1RO-snmpV3NoAccess(5)} ACCESS read-write STATUS current DESCRIPTION "Manages an SNMP version's read and write access to the MIB." ::= { npCtl 27 } npCtlBonjour OBJECT-TYPE SYNTAX Integer32 (0..1) ACCESS read-write STATUS current DESCRIPTION "Configure Multicast Domain Name Service. (0) = Bonjour disabled (1) = Bonjour enabled" ::= { npCtl 29 } npPortNumPorts OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "The number of peripheral interfaces supported by this device." ::= { npPort 1 } npDHCPserver OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS current DESCRIPTION "IP address of DHCP server that provided this unit with an IP address via the DHCP protocol." ::= { npDhcp 2 } gdStatusBytes OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "The number of valid bytes in the gdStatusEntry array." ::= { generalDeviceStatus 1 } gdStatusDisplay OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS current DESCRIPTION "The string diplayed on the peripheral front panel. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this is always a zero length string." ::= { generalDeviceStatus 3 } gdStatusId OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS current DESCRIPTION "A formatted string of NVT ASCII charactersdescribing this peripheral." ::= { generalDeviceStatus 7 } gdStatusJobTimeout OBJECT-TYPE SYNTAX Integer32 ACCESS read-write STATUS obsolete ::= { generalDeviceStatus 10 } gdPasswords OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS current DESCRIPTION "This object is used as a 256 byte NVRAM area for JetAdmin. It is completely managed by JetAdmin. Initially it is initialized to all zeros. A coldboot will re-initialize to all zeros." ::= { generalDeviceStatus 13 } npNpiPaeClass OBJECT-TYPE SYNTAX INTEGER {printer(1), plotter(2), xStation(3)} ACCESS read-only STATUS current DESCRIPTION "The class assigned to the peripheral onto which this card is plugged." ::= { npNpiPeripheralAttributeEntry 2 } npNpiPaeIdentification OBJECT-TYPE SYNTAX INTEGER {laserjet-IIISI(1), laserjet-4SI(5)} ACCESS read-only STATUS current DESCRIPTION "The Identification number of the peripheral. These values are defined in the MIO spec. DesignJet, PaintJet XL300, and DesignJet/600 peripherals will identify themselves as LaserJet-IIIsi." ::= { npNpiPeripheralAttributeEntry 3 } npNpiCaeClass OBJECT-TYPE SYNTAX INTEGER {rs-232(1), centronics(2), csma-cd-network(3), token-ring-network(4), scsi(5), hpib(6), localtalk(7), hpna(8), usb(9), firewire(10), bluetooth(11), ieee802-11b(12)} ACCESS read-only STATUS current DESCRIPTION "The class of this network peripheral card." ::= { npNpiCardAttributeEntry 2 } gdStatusLineState OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This describes the line state of the peripheral. When non-zero, the peripheral is off-line. When zero the peripheral is on-line." ::= { gdStatusEntry 1 } gdStatusPaperState OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This describes the state of the paper on the peripheral. When non-zero, the peripheral has a paper problem. When zero, the peripheral does not have a paper problem." ::= { gdStatusEntry 2 } gdStatusInterventionState OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This describes the intervention state of the peripheral. When non-zero, the peripheral requires human intervention to continue working. When zero, it requires no assistance." ::= { gdStatusEntry 3 } gdStatusPeripheralError OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This is the error code from the peripheral." ::= { gdStatusEntry 6 } gdStatusPaperOut OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral is out of paper. off (0), paper-out-or-paper-mount (1), manual-paper-feed-needed (2) For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 8 } gdStatusPaperJam OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral has a paper jam. off (0), paper-jam(1) For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 9 } gdStatusTonerLow OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral has a low toner condition. off (0), toner-low (1), no-toner-cartridge (2) For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 10 } gdStatusPagePunt OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral did not receive data fast enough to keep up with the print engine when generating a page. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 11 } gdStatusMemoryOut OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral did not have enough memory to render an image on a page. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 12 } gdStatusIoActive OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral is processing data from this I/O interface card. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0). For X.20.06 firmware and later firmware releases, this object is not relevant. In order not to break legacy applications which call this object in multi-varbind requests, this value is always zero (0)." ::= { gdStatusEntry 13 } gdStatusBusy OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral is busy processing print/plot data. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 14 } gdStatusWait OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral is waiting for print/plot data to process. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 15 } gdStatusInitialize OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral is initializing or warming up. off (0), initializing (1), warm-up(2) For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 16 } gdStatusDoorOpen OBJECT-TYPE SYNTAX Integer32 (0..255) ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral cover or door is open. For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 17 } gdStatusPrinting OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral is printing or otherwise marking or moving paper. off (0), ordinary-page (1), test-fonts-config-or-start-page (2) For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 18 } gdStatusPaperOutput OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS current DESCRIPTION "This indicates that the peripheral has a paper output problem such as the output storage bin being full. off (0), output-storage-full (1) For some peripherals, such as the HP LaserJet IIISi printer or HP DesignJet plotter, this value is always a zero (0)." ::= { gdStatusEntry 19 } energy-star OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "Returns or changes the Energy Star sleep value. If the value is greater than zero, then the device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. A value of zero means Energy Star is disabled and the device will not go to sleep based on print engine idle time. The value must be non-negative. Additional information: The product will always be in sleep mode when not processing data. This object will always return a value of 1." ::= { settings-system 1 } sleep-mode OBJECT-TYPE SYNTAX INTEGER { eFalse(1), eTrue(2) } ACCESS read-only STATUS optional DESCRIPTION "Returns eTrue if the device is in energy saving sleep mode, otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes the device to wake up, if it is in sleep mode. Setting SLEEP-MODE to eTrue causes the device to go into sleep mode. Additional information: The product will always be in sleep mode except when either processing a print job or in an error state." ::= { settings-system 2 } service-password OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS optional DESCRIPTION "When set to the password value, other service related objects become 'visible' (i.e readable) or become writable. When written with any other value, the service related objects become 'hidden' (i.e. are no longer readable) or are not longer writable. The objects that can be effected by the SERVICE-PASSWORD object include: SERIAL-NUMBER and TOTAL-ENGINE-PAGE-COUNT. The password value, and the list of objects effected by the SERVICE-PASSWORD being set to the correct value, should be documented in the device POS. Additional information: The objects that can be effected by the SERVICE- PASSWORD are: SCANNER-JAM-PAGE-COUNT, SCANNER-ADF-PAGE -COUNT, SCAN-ADF-PAGE-COUNT, SCANNER-RETRIEVE-SCANLINE, SCANNER-MOTOR-CONTROL, COPIER-ADF-PAGE-COUNT, COPIER- PRINT-PAGE-COUNT, TOTAL-ENGINE-PAGE-COUNT, PRINT-ENGINE- JAM-COUNT, PRINT-ENGINE-MISPICK-COUNT, CLEAR-NVRAM" ::= { settings-system 9 } device-configure-custom-product-number OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "This object allows manufacturing to change the product number to a pre-defined alternate after release. This feature will allow manufacturing to assign unique product numbers to custom product bundles when the device is unable to determine its product number in firmware. For example, A HP Color LaserJet CP1515n could be configured to display CP1516n to the customer. This product number must be defined prior to release. Additional information: This object allows manufacturing to change the product number to a pre-defined alternate after release. This feature will allow manufacturing to assign unique product numbers to custom product bundles when the device is unable to determine its product number in firmware. For example, A HP Color LaserJet CP1515n could be configured to display CP1516n to the customer. This product number must be defined prior to release." ::= { device-configure 19 } control-panel-button-press-delay OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "This object gives the number of seconds to wait before simulating the button press when CONTROL-PANEL-BUTTON-PRESS is next called. Additional information: This object gives the number of seconds to wait before simulating the button press when CONTROL-PANEL-BUTTON-PRESS is next called." ::= { settings-system 47 } low-power OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the Auto Low Power sleep value. The device will go into energy saving Auto Low Power mode after the print engine has been idle for the number of seconds specified by this object. Frida supports values of 300 until 14400 seconds. If the value is invalid then it will return status of PML_Status_ErrUnsupValue and will not issue command to the engine. Additional information: Returns or changes the Auto Low Power sleep value. The device will go into energy saving Auto Low Power mode after the print engine has been idle for the number of seconds specified by this object. The product supports values of 0 (Off), 60 (1 minute), 900 (15 minutes), 1800 (30 minutes), 3600 (1 hour), 7200 (2 hours), and 14400 (4 hours). If the value is invalid then it will return a status of PML_ERROR_INVALID_OR_UNSUPPORTED_VALUE and will not issue a command to the engine." ::= { settings-system 49 } control-panel-display-contrast OBJECT-TYPE SYNTAX INTEGER { eLightest(1), eLight(2), eMedium(3), eDark(4), eDarkest(5) } ACCESS read-write STATUS optional DESCRIPTION "This object returns or sets the display contrast setting if the control panel has a display and it supports contrast adjustment. The setting Is stored in NVRAM, so the value is saved over power cycles. Additional information: This object returns or sets the display contrast setting if the control panel has a display and it supports contrast adjustment. The setting is stored in NVRAM, so the value is saved over power cycles." ::= { settings-system 73 } io-timeout OBJECT-TYPE SYNTAX INTEGER(5..7200) ACCESS read-write STATUS optional DESCRIPTION "The amount of time, in seconds, to wait for more print job data to be received before an I/O timeout occurs. The I/O channel being timed is the I/O channel that received the data associated with the current print job. If an I/O timeout occurs, the PDL processing sub-system assumes all the data associated with the current print job has been received, and processes the end of job in a PDL specific manner. The POS specifies the supported values. Additional information: If an I/O timeout occurs,the PDL processing sub-system will consider it an end of job condition only if there is data from another I/O subsystem waiting to be processed. The supported values are 5 to 7200 seconds. Setting to a value outside the supported range returns status." ::= { settings-io 1 } io-switch OBJECT-TYPE SYNTAX INTEGER { eYes(1) } ACCESS read-only STATUS optional DESCRIPTION "Indicates if the device will switch between I/O channels when a job boundary is encountered and print job data is available on another I/O channel." ::= { settings-io 2 } default-copies OBJECT-TYPE SYNTAX INTEGER(1..999) ACCESS read-write STATUS optional DESCRIPTION "Returns or changes default copies. Default copies is the default values used by the PDL to control the number of copies of each page in the print job that are printed. The print job can override this value. The list of supported values should be documented in the device POS. Additional information: The supported values are 1 through 999. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snaps are as follows: <1 snaps to >999 snaps to 999" ::= { settings-pdl 4 } default-vertical-black-resolution OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the value of the default vertical black resolution. The units are dots per inch. Additional information: In the product, changing this OID also causes DEFAULT-HORIZONTAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are 600, and 1200. When the default monochrome resolution or bits-per-pixel are changed to anything other than 600x1 the product no longer prints color jobs. Color jobs are always 600x1. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follows: <450 will snap to 600 >=450 and <900 will snap to 600 >=900 will snap to 1200" ::= { settings-pdl 8 } default-horizontal-black-resolution OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the value of the default horizontal black resolution. The units are dots per inch. Additional information: In the product, changing this OID also causes DEFAULT-VERTICAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are 600 and 1200. When the default monochrome resolution or bits-per-pixel are changed to anything other than 600x1 the product no longer prints color jobs. Color jobs are always 600x1. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follows: <450 snaps to 600 >=450 and <900 snaps to 600 >=900 snaps to 1200" ::= { settings-pdl 9 } default-lines-per-page OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the default number of lines per page. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return the . Additional information: The supported values in the product are 5 to 128. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follows: <5 snaps to 5 >128 snaps to 128" ::= { settings-pdl 11 } default-vmi OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the default vertical motion index. The unit of measure for VMI is centipoints per line. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return . Additional information: Setting this object may cause DEFAULT-LINES-PER-PAGE to change." ::= { settings-pdl 12 } default-media-size OBJECT-TYPE SYNTAX INTEGER { eUSExecutive(1), eUSLetter(2), eUSLegal(3), eFoolscap(10), eROC16K(17), eISOandJISA4(26), eISOandJISA5(25), eROC16K195X270(34), eJISB5(45), eISOB5(65), eJapanesePostcardSingle(71), eJapanesePostcardDouble(72), eMonarch(80), eCommercial10(81), eROC16K184X260(89), eInternationalDL(90), eInternationalC5(91), eInternationalB5(100), eCustom(101) } ACCESS read-write STATUS optional DESCRIPTION "This indicates the default media size. A write of an unsupported value causes an . Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document. (for a full list of media size enums see the end of this file) " ::= { settings-pdl 13 } cold-reset-media-size OBJECT-TYPE SYNTAX INTEGER { eUSLetter(2), eISOandJISA4(26) } ACCESS read-write STATUS optional DESCRIPTION "Returns or sets the media size that is used as the DEFAULT-MEDIA-SIZE when a cold reset occurs." ::= { settings-pdl 19 } default-media-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS optional DESCRIPTION "Returns or sets the media name that is used until the media name is changed by a print job command. Additional information: This string must be one of the MEDIAn-NAME objects, except it cannot be set to ANY. The value of this object is saved across a power cycle." ::= { settings-pdl 22 } reprint OBJECT-TYPE SYNTAX INTEGER { eOff(1), eOn(2), eAuto(3) } ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the reprint (jam recovery) setting. If eOn, then the device will reprint pages jammed pages. If eOff, the device will not attempt to reprint jammed pages. If eAuto, a device dependent algorithm (which should be documented in the POS) will be used to determine if the page gets reprinted. This object controls all PDLs, unless a specific PDL supports its own reprint control mechanism. To date, only PostScript has a PDL reprint control mechanism. Additional information: Setting this object when the printer is not idle, may cause a status of to be returned, but the new value will not take effect until a job boundary is reached. If a get is done on object before the job boundary is reached, the value last set will be returned. When the value is set to eOff, pages will not be stored in the printer, and in the event of a paper jam, will have to be reprinted. When the value is set to eOn, pages will be stored until delivery, therefore, in the event of a paper jam, the page will be reprinted. When the value is set to eAuto, the printer will behave as though it is eOff when there is less than seven megabytes of memory installed in the printer. When additional memory is installed, to total at least seven megabytes of RAM, the setting of eAuto will behave as though it was set to eOn." ::= { settings-pdl 36 } wide-a4 OBJECT-TYPE SYNTAX INTEGER { eOff(1), eOn(2) } ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the wide A4 logical page size setting. If eOn, then the margins/printable area of A4 paper will be changed to allow 80 10-pitch characters to be printed on a single line. If eOff then the industry standard A4 logical page size is used." ::= { settings-pdl 37 } dark-courier OBJECT-TYPE SYNTAX INTEGER { eOff(1), eOn(2) } ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the dark Courier setting. If eOn, then the Courier font used will approximate the same darkness as the LaserJet III printer. If eOff, then the Courier font used will approximate the same darkness as the LaserJet 4 printer." ::= { settings-pdl 38 } default-bits-per-pixel OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Controls the number of levels used (per pixel) when printing grayscale or color images." ::= { settings-pdl 39 } pcl-total-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of PCL pages printed by the device." ::= { pdl-pcl 5 } pcl-default-font-height OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the default PCL height. Height is an approximate measure of the body of the type in centipoints. A centipoint is 1/7200 inch. Height applies only to proportional fonts. Point size, in points, can be converted to font height, in centipoints, by multiplying the point size by 100. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return . ''Closest'' means the smallest absolute difference. Additional information: This object refers to the font point size with 400 representing the smallest settable font (4) and 99975 representing the largest settable font (999.75). The default of 1200 is a font point size of 12. Supported values range from 400 to 99975. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follows: <=400 snaps to 400 >=99975 snaps to 99975 Fonts are settable to the nearest quarter point size (i.e. 10, 10.25, 10.50, 10.75). Unsupported values in the range 401 to 99974 snap DOWN to the previous supported value (i.e 25293 snaps to 25275 or 75038 snaps to 75025)." ::= { pdl-pcl 13 } pcl-default-font-source OBJECT-TYPE SYNTAX INTEGER { eInternal(1), ePermanentSoft(2), eRomSimm1(10) } ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the value of the default font source variable in NVRAM." ::= { pdl-pcl 14 } pcl-default-font-number OBJECT-TYPE SYNTAX INTEGER(0..255) ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the value of the default font number variable in NVRAM. Writing an unsupported value causes the printer to generate an . Additional information: Valid numbers or 0 - 255, but only font numbers that are included in the PCL FONT LIST are selectable." ::= { pdl-pcl 15 } pcl-default-font-width OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the default PCL font width. Width is expressed as the width of a character in centipoints. A centipoint is 1/7200 inch. Width applies only to fixed space fonts. Pitch, in character per inch, can be converted to font width, in centipoints, by dividing 7200 by the pitch. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return . ''Closest'' means the smallest absolute difference. Additional information: Setting to an unsupported value causes the printer to substitue in a snap value (listed below) and return status. The snap values for pitch are as follow: <=44 snaps to 44 >=9999 snaps to 9999 Unsupported values in the range 44 - 9999 (.44 - 99.99) snap DOWN to the next supported value." ::= { pdl-pcl 16 } postscript-total-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of PostScript pages printed by the device." ::= { pdl-postscript 5 } postscript-print-errors OBJECT-TYPE SYNTAX INTEGER { eOff(1), eOn(2) } ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the time of the error. Additional information: Returns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the time of the error." ::= { pdl-postscript 11 } pclxl-total-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of PCLXL pages printed by the device." ::= { pdl-pclxl 1 } pjl-password OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "Returns PJL password, if the password is not set (zero). If the password is set, then attempting to retrieve the password causes an to occur and will return the ." ::= { pjl 1 } print-density OBJECT-TYPE SYNTAX INTEGER(1..5) ACCESS read-write STATUS optional DESCRIPTION "Returns or sets the print density setting. Print density is the instantaneous amount of marking agent applied to the paper while printing. A value of zero has the lowest print density, yielding a lighter page. A value of 10 has the highest print density, yielding a darker page. Each POS should document what values in the 0 to 10 range are supported. Additional information: When this value is written, the page pipeline will be flushed (all pages being printed are completed, no new ones are started), the new density setting is set and printing resumes. The acutal change in print density may be gradual over several pages. The supported values are 1 through 5. Setting to an unsupported value causes the printer to substitue in a a snap value and to return status. The snap values are as follows: <1 snaps to 1 >5 snaps to 5." ::= { settings-prt-eng 5 } invalid-personality-reports-enabled OBJECT-TYPE SYNTAX INTEGER { eDisabled(1), eEnabled(2) } ACCESS read-write STATUS optional DESCRIPTION "Read or configure wether invalid personality reports are enabled or disabled for a product." ::= { settings-prt-eng 18 } total-engine-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of pages printed by the device. POS indicates if the total engine page count is kept in NVRAM, and the maximum supported value before the page count rolls over to zero. Additional information: This object is stored in NVRAM. The maximum value of this count is 1000000 before it rolls over to zero." ::= { status-prt-eng 5 } print-engine-jam-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of pages jammed in the print engine's life time. The POS indicates if the total jam count is kept in NVRAM and the maximum supported value before the jam count rolls over to zero. Additional information: This object is stored in NVRAM. The maximum value of this count is 65000 before it rolls over to zero." ::= { status-prt-eng 34 } print-engine-mispick-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of pages mispicked in the print engine's life time. The POS indicates if the total mispick count is kept in NVRAM and the maximum supported value before the mispick count rolls over to zero. Additional information: This object is stored in NVRAM. The maximum value of this count is 65000 before it rolls over to zero." ::= { status-prt-eng 35 } supply-out-device-state OBJECT-TYPE SYNTAX INTEGER { eNoSupplyOut(1), eOffline(2), eSupplyOutOverride(3), eMonochromePrintingAfterColorCartridgeOut(4) } ACCESS read-only STATUS optional DESCRIPTION "This PML object indicates the current behavior of the device if one or more supplies have reached out. If no supply has reached out, the value of this PML object is eNoSupplyOut. If one or more supplies have reached out, the value of this PML object will indicate if the printer is online and if so what mode is being used to continue printing. Additional information: This PML object indicates the current behavior of the device if one or more supplies have reached out. If no supply has reached out, the value of this PML object is eNoSupplyOut. If one or more supplies have reached out, the value of this PML object will indicate if the printer is online and if so what mode is being used to continue printing. If the printer is in both eSupplyOutOverride and eMonochromePrintingAfterColorCartridgeOut then eMonochromePrintingAfterColorCartridgeOut will be returned." ::= { status-prt-eng 49 } duplex-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Total number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not marks are made on the page. The POS will indicate if the value is kept in NVRAM. Additional information: Total number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not marks are made on the page. This object is stored in NVRAM. The maximum value of this count is 65000 before it rolls over to zero." ::= { status-prt-eng 22 } print-engine-revision OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Print engine revision string. Additional information: Print engine revision string." ::= { status-prt-eng 26 } custom-paper-dim-unit OBJECT-TYPE SYNTAX INTEGER { eTenThousandthsOfInches(3), eMicrometers(4) } ACCESS read-write STATUS optional DESCRIPTION "The units of measure used to specify the width and height of the printer's custom paper. The unit of measure of eTenThousandthsOfInches is 0.0001 inches. Additional information: The only valid values for this object are eTenThousandthsOfInches (3), and eMicrometers (4). The data for this object is stored in NVRAM." ::= { settings-intray 7 } custom-paper-feed-dim OBJECT-TYPE SYNTAX INTEGER(50000..140000) ACCESS read-write STATUS optional DESCRIPTION "Sets the printer's custom paper dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product. Additional information: The valid range is 50000 to 140000 if CUSTOM-PAPER_DIM_UNIT is eTenThousandthsOfInches or 127000 to 355600 if CUSTOM-PAPER-DIM-UNIT is ePmicrometers. Attempts to set this object outside the valid range will result in a return value of ERROR_INVALID_OR_UNSUPPORTED_VALUE." ::= { settings-intray 8 } custom-paper-xfeed-dim OBJECT-TYPE SYNTAX INTEGER(30000..85000) ACCESS read-write STATUS optional DESCRIPTION "Sets the printer's custom paper dimension in the cross-feed direction (direction ninety degrees relative to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product. Additional information: The valid range for the product is 30000 to 85000 if CUSTOM-PAPER-DIM-UNIT is eTenThousandthsOfInches or 76200 to 215900 if CUSTOM-PAPER-DIM-UNIT is ePmicrometers. Attempts to set this object outside the valid range will result in a return value of ." ::= { settings-intray 9 } tray1-media-size-loaded OBJECT-TYPE SYNTAX INTEGER { eUSExecutive(1), eUSLetter(2), eUSLegal(3), eFoolscap(10), eROC16K(17), eISOandJISA6(24), eISOandJISA5(25), eISOandJISA4(26), eROC16K195X270(34), eJISB5(45), eJapansePostcardSingle(71), eJapansePostcardDouble(72), eIndexCard5x8(75), ePhoto4x6(76), eMonarch(80), eCommercial10(81), eROC16K184X260(89), eInternationalDL(90), eInternationalC5(91), eInternationalB5(100), eCustom(101), ePhoto10x15(118), eAnySize(32765) } ACCESS read-write STATUS optional DESCRIPTION "Returns the media size that is currently configuredconfigured in tray #1. This object can be set to indicate the media size currently loaded, if the printer supports input trays that can not sense the media size. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document." ::= { intray1 1 } tray2-media-size-loaded OBJECT-TYPE SYNTAX INTEGER { eUSExecutive(1), eUSLetter(2), eUSLegal(3), eFoolscap(10), eROC16K(17), eISOandJISA6(24), eISOandJISA5(25), eISOandJISA4(26), eROC16K195X270(34), eJISB5(45), eJapansePostcardSingle(71), eJapansePostcardDouble(72), eIndexCard5x8(75), ePhoto4x6(76), eMonarch(80), eCommercial10(81), eROC16K184X260(89), eInternationalDL(90), eInternationalC5(91), eInternationalB5(100), eCustom(101), ePhoto10x15(118), eAnySize(32765) } ACCESS read-write STATUS optional DESCRIPTION "Returns the media size that is currently configured in tray #2. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document." ::= { intray2 1 } tray3-media-size-loaded OBJECT-TYPE SYNTAX INTEGER { eUSExecutive(1), eUSLetter(2), eUSLegal(3), eFoolscap(10), eROC16K(17), eISOandJISA6(24), eISOandJISA5(25), eISOandJISA4(26), eROC16K195X270(34), eJISB5(45), eJapansePostcardSingle(71), eJapansePostcardDouble(72), eIndexCard5x8(75), ePhoto4x6(76), eMonarch(80), eCommercial10(81), eROC16K184X260(89), eInternationalDL(90), eInternationalC5(91), eInternationalB5(100), eCustom(101), ePhoto10x15(118), eAnySize(32765) } ACCESS read-write STATUS optional DESCRIPTION "Returns the media size that is currently configured in tray #3. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document." ::= { intray3 1 } default-ret OBJECT-TYPE SYNTAX INTEGER { eOff(1), eLight(2), eMedium(3), eDark(4) } ACCESS read-write STATUS optional DESCRIPTION "Returns or changes the Resolution Enhancement Technology setting. Devices that only support eOff and eOn should map all other values to eOn and always return the same non-eOff value to indicatep on. The list of supported values should be documented in the device POS." ::= { imaging 5 } media-names-available OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "The value of this object controls which of the MEDIAx-NAME objects are supported. If a bit is set to zero, then attempting to get or set the corresponding MEDIAx-NAME objects will return . Additional information: Since this object is read-only, the corresponding MEDIAx objects will always be available. The DEFAULTS below represent which MediaNameX is available on this product of the total possible available defined in SYNTAX, so the collection is like a bitfield. Raptor does not support cMediaName32Available" ::= { settings-print-media 1 } media1-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 1 name. Additional information: The symbol set for this string is Roman-8." ::= { media1 1 } media1-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: The engine processing characteristics that are to be applied to this media type. Currently, 'engine processing characteristics' denotes changes to fusing temperature and/or transfer roller voltage." ::= { media1 4 } media2-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 2 name. Additional information: The symbol set for this string is Roman-8." ::= { media2 1 } media2-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media2 4 } media3-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 3 name. Additional information: The symbol set for this string is Roman-8." ::= { media3 1 } media3-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media3 4 } media4-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 4 name. Additional information: The symbol set for this string is Roman-8." ::= { media4 1 } media4-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media4 4 } media5-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 5 name. Additional information: The symbol set for this string is Roman-8." ::= { media5 1 } media5-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE. Raptor will havea default value of 4" ::= { media5 4 } media6-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 6 name. Additional information: The symbol set for this string is Roman-8." ::= { media6 1 } media6-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 5. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media6 4 } media7-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 7 name. Additional information: The symbol set for this string is Roman-8." ::= { media7 1 } media7-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 5. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media7 4 } media8-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 8 name. Additional information: The symbol set for this string is Roman-8." ::= { media8 1 } media8-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 6. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media8 4 } media9-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 9 name. Additional information: The symbol set for this string is Roman-8." ::= { media9 1 } media9-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 7. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media9 4 } media10-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 10 name. Additional information: The symbol set for this string is Roman-8." ::= { media10 1 } media10-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media10 4 } media11-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 11 name. Additional information: The symbol set for this string is Roman-8." ::= { media11 1 } media11-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 8. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media11 4 } media12-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 12 name. Additional information: Raptor will have a default value of 'Light'. The symbol set for this string is Roman-8." ::= { media12 1 } media12-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 2. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media12 4 } media13-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 13 name. Additional information: Raptor will have a default value of 'Mid Weight' The symbol set for this string is Roman-8." ::= { media13 1 } media13-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 3 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media13 4 } media14-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 14 name. Additional information: Raptor will have a default value of 'Heavy' The symbol set for this string is Roman-8." ::= { media14 1 } media14-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 4 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media14 4 } media15-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 15 name. Additional information: Raptor will have a default value of 'Extra Heavy' The symbol set for this string is Roman-8." ::= { media15 1 } media15-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 5 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media15 4 } media16-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 16 name. Additional information: Raptor will have a default value of 'Heavy Gloss' The symbol set for this string is Roman-8." ::= { media16 1 } media16-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 6 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media16 4 } media17-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 17 name. Additional information: Raptor will have a default value of 'Extra Heavy Gloss' The symbol set for this string is Roman-8." ::= { media17 1 } media17-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 7 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media17 4 } media18-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 18 name. Additional information: Raptor will have a default value of 'Card Glossy' The symbol set for this string is Roman-8." ::= { media18 1 } media18-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 8. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media18 4 } media19-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 19 name. Additional information: Raptor will have a default value of 'Transparency' The symbol set for this string is Roman-8." ::= { media19 1 } media19-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 10 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media19 4 } media20-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 20 name. Additional information: Raptor will have a default value of 'Labels' The symbol set for this string is Roman-8." ::= { media20 1 } media20-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 11 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media20 4 } media21-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 21 name. Additional information: Raptor will have a default value of 'Letterhead' The symbol set for this string is Roman-8." ::= { media21 1 } media21-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 1. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media21 4 } media22-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 22 name. Additional information: Raptor will have a default value of 'Envelope' The symbol set for this string is Roman-8." ::= { media22 1 } media22-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 12. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media22 4 } media23-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 23 name. Additional information: Raptor will have a default value of 'Heavy Envelope' The symbol set for this string is Roman-8." ::= { media23 1 } media23-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 13 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media23 4 } media24-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 24 name. Additional information: Raptor will have a default value of 'Preprinted' The symbol set for this string is Roman-8." ::= { media24 1 } media24-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 1 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media24 4 } media25-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 25 name. Additional information: Raptor will have a default value of 'Prepunched' The symbol set for this string is Roman-8." ::= { media25 1 } media25-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 1 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media25 4 } media26-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 26 name. Additional information: Raptor will have a default value of 'Color' The symbol set for this string is Roman-8." ::= { media26 1 } media26-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media26 4 } media27-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 27 name. Additional information: Raptor will have a default value of 'Bond' The symbol set for this string is Roman-8." ::= { media27 1 } media27-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 3 See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media27 4 } media28-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 28 name. Additional information: Raptor will have a default value of 'Recycled' The symbol set for this string is Roman-8." ::= { media28 1 } media28-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media28 4 } media29-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 29 name. Additional information: Raptor will have a default value of 'Rough' The symbol set for this string is Roman-8." ::= { media29 1 } media29-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media29 4 } media30-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 30 name. Additional information: Raptor will have a default value of 'Heavy Rough' The symbol set for this string is Roman-8." ::= { media30 1 } media30-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 5. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media30 4 } media31-name OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "Media 31 name. Additional information: Raptor will have a default value of 'HP Tough Paper'. The symbol set for this string is Roman-8." ::= { media31 1 } media31-engine-media-mode OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: Raptor will have a default value of 14. See the description for MEDIA1-ENGINE-MEDIA-MODE." ::= { media31 4 } engine-media-modes-supported1 OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional DESCRIPTION "The list of engine media modes supported by the device. The modes are each separated by a comma character. An example string would be: 'Normal,Rough,Low,Vellum'. Additional information: The list of engine media modes supported by the device. The modes are each separated by a comma character. An example string would be: 'Normal,Rough,Low,Vellum'. Raptor does not support 'Photo2' but supports 'Extra Heavy'" ::= { media-modes 1 } pe-test-cause-assert OBJECT-TYPE SYNTAX INTEGER { e49DEAD(1), e494C02(2) } ACCESS write-only STATUS optional DESCRIPTION "This object allows the user to cause a 49 Error. Additional information: This object allows the user to cause a 49 Error." ::= { print-engine-test 111 } pe-test-cause-79error OBJECT-TYPE SYNTAX INTEGER { e79DEAD(1) } ACCESS write-only STATUS optional DESCRIPTION "This object allows the user to cause a 79 Error. Additional information: This object allows the user to cause a 79 Error." ::= { print-engine-test 116 } consumable-reorder-url OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..64)) ACCESS read-write STATUS optional DESCRIPTION "This object is used to read and write the URL that can be used to reorder consumables for this device. This URL is set at the factory but can be updated by a reseller or third party. Additional information: The URL can be up to 64 characters long." ::= { consumables 2 } END