1459 lines
54 KiB
Plaintext
1459 lines
54 KiB
Plaintext
BFD-STD-MIB-R DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
|
|
Integer32, Unsigned32, Counter32, Counter64
|
|
FROM SNMPv2-SMI
|
|
|
|
TruthValue, RowStatus, StorageType, TimeStamp
|
|
FROM SNMPv2-TC
|
|
|
|
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
|
|
FROM SNMPv2-CONF
|
|
|
|
InterfaceIndexOrZero
|
|
FROM IF-MIB
|
|
|
|
InetAddress, InetAddressType, InetPortNumber
|
|
FROM INET-ADDRESS-MIB
|
|
|
|
BfdSessIndexTC, BfdIntervalTC, BfdMultiplierTC, BfdDiagTC,
|
|
BfdSessTypeTC, BfdSessOperModeTC, BfdCtrlDestPortNumberTC,
|
|
BfdCtrlSourcePortNumberTC, BfdSessStateTC,
|
|
BfdSessAuthenticationTypeTC, BfdSessionAuthenticationKeyTC
|
|
FROM BFD-TC-STD-MIB-R;
|
|
|
|
bfdMIB MODULE-IDENTITY
|
|
LAST-UPDATED "201204141200Z" -- 14 June 2012 12:00:00 EST
|
|
ORGANIZATION "IETF Bidirectional Forwarding Detection
|
|
Working Group"
|
|
CONTACT-INFO
|
|
"Thomas D. Nadeau
|
|
Juniper Networks
|
|
Email: tnadeau@lucidvision.com
|
|
|
|
Zafar Ali
|
|
Cisco Systems, Inc.
|
|
Email: zali@cisco.com
|
|
|
|
Nobo Akiya
|
|
Cisco Systems, G.K.
|
|
Email: nobo@cisco.com"
|
|
DESCRIPTION
|
|
"Bidirectional Forwarding Management Information Base."
|
|
REVISION "201204141200Z" -- 14 June 2012 12:00:00 EST
|
|
DESCRIPTION
|
|
"Initial version. Published as RFC xxxx."
|
|
::= { radExperimental 15 }
|
|
radExperimental OBJECT IDENTIFIER ::= { iso (1) org (3) dod (6) internet (1) private (4) enterprises (1) rad (164) 20 }
|
|
|
|
-- RFC Ed.: RFC-editor pls fill in xxxx
|
|
-- ::= { mib-2 XXX }
|
|
-- RFC Ed.: assigned by IANA, see section 7.1 for details
|
|
|
|
-- Top level components of this MIB module.
|
|
|
|
bfdNotifications OBJECT IDENTIFIER ::= { bfdMIB 0 }
|
|
|
|
bfdObjects OBJECT IDENTIFIER ::= { bfdMIB 1 }
|
|
|
|
bfdConformance OBJECT IDENTIFIER ::= { bfdMIB 2 }
|
|
|
|
bfdScalarObjects OBJECT IDENTIFIER ::= { bfdObjects 1 }
|
|
|
|
-- BFD General Variables
|
|
|
|
-- These parameters apply globally to the Systems'
|
|
-- BFD Process.
|
|
|
|
bfdAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The global administrative status of BFD in this device.
|
|
The value 'enabled' denotes that the BFD Process is
|
|
active on at least one interface; 'disabled' disables
|
|
it on all interfaces."
|
|
DEFVAL { enabled }
|
|
::= { bfdScalarObjects 1 }
|
|
|
|
bfdSessNotificationsEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If this object is set to true(1), then it enables
|
|
the emission of bfdSessUp and bfdSessDown
|
|
notifications; otherwise these notifications are not
|
|
emitted."
|
|
REFERENCE
|
|
"See also RFC3413 for explanation that
|
|
notifications are under the ultimate control of the
|
|
MIB modules in this document."
|
|
DEFVAL { false }
|
|
::= { bfdScalarObjects 2 }
|
|
|
|
-- BFD Session Table
|
|
-- The BFD Session Table specifies BFD session specific
|
|
-- information.
|
|
|
|
bfdSessTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF BfdSessEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Table describes the BFD sessions."
|
|
REFERENCE
|
|
"Katz, D. and D. Ward, Bidirectional Forwarding
|
|
Detection (BFD), RFC 5880, June 2012."
|
|
::= { bfdObjects 2 }
|
|
|
|
bfdSessEntry OBJECT-TYPE
|
|
SYNTAX BfdSessEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Entry describes BFD session."
|
|
INDEX { bfdSessIndex }
|
|
::= { bfdSessTable 1 }
|
|
|
|
BfdSessEntry ::= SEQUENCE {
|
|
bfdSessIndex BfdSessIndexTC,
|
|
bfdSessVersionNumber Unsigned32,
|
|
bfdSessType BfdSessTypeTC,
|
|
bfdSessDiscriminator Unsigned32,
|
|
bfdSessRemoteDiscr Unsigned32,
|
|
bfdSessDestinationUdpPort BfdCtrlDestPortNumberTC,
|
|
bfdSessSourceUdpPort BfdCtrlSourcePortNumberTC,
|
|
bfdSessEchoSourceUdpPort InetPortNumber,
|
|
bfdSessAdminStatus INTEGER,
|
|
bfdSessState BfdSessStateTC,
|
|
bfdSessRemoteHeardFlag TruthValue,
|
|
bfdSessDiag BfdDiagTC,
|
|
bfdSessOperMode BfdSessOperModeTC,
|
|
bfdSessDemandModeDesiredFlag TruthValue,
|
|
bfdSessControlPlaneIndepFlag TruthValue,
|
|
bfdSessMultipointFlag TruthValue,
|
|
bfdSessInterface InterfaceIndexOrZero,
|
|
bfdSessSrcAddrType InetAddressType,
|
|
bfdSessSrcAddr InetAddress,
|
|
bfdSessDstAddrType InetAddressType,
|
|
bfdSessDstAddr InetAddress,
|
|
bfdSessGTSM TruthValue,
|
|
bfdSessGTSMTTL Unsigned32,
|
|
bfdSessDesiredMinTxInterval BfdIntervalTC,
|
|
bfdSessReqMinRxInterval BfdIntervalTC,
|
|
bfdSessReqMinEchoRxInterval BfdIntervalTC,
|
|
bfdSessDetectMult BfdMultiplierTC,
|
|
bfdSessNegotiatedInterval BfdIntervalTC,
|
|
bfdSessNegotiatedEchoInterval BfdIntervalTC,
|
|
bfdSessNegotiatedDetectMult BfdMultiplierTC,
|
|
bfdSessAuthPresFlag TruthValue,
|
|
bfdSessAuthenticationType BfdSessAuthenticationTypeTC,
|
|
bfdSessAuthenticationKeyID Integer32,
|
|
bfdSessAuthenticationKey BfdSessionAuthenticationKeyTC,
|
|
bfdSessStorageType StorageType,
|
|
bfdSessRowStatus RowStatus
|
|
}
|
|
|
|
bfdSessIndex OBJECT-TYPE
|
|
SYNTAX BfdSessIndexTC
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains an index used to represent a
|
|
unique BFD session on this device."
|
|
::= { bfdSessEntry 1 }
|
|
|
|
bfdSessVersionNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..7)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The version number of the BFD protocol that this session
|
|
is running in. Write access is available for this object
|
|
to provide ability to set desired version for this
|
|
BFD session."
|
|
REFERENCE
|
|
"Katz, D. and D. Ward, Bidirectional Forwarding
|
|
Detection (BFD), RFC 5880, June 2012."
|
|
DEFVAL { 1 }
|
|
::= { bfdSessEntry 2 }
|
|
|
|
bfdSessType OBJECT-TYPE
|
|
SYNTAX BfdSessTypeTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the type of this BFD session."
|
|
::= { bfdSessEntry 3 }
|
|
|
|
bfdSessDiscriminator OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the local discriminator for this BFD
|
|
session, used to uniquely identify it."
|
|
::= { bfdSessEntry 4 }
|
|
|
|
bfdSessRemoteDiscr OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0 | 1..4294967295)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the session discriminator chosen
|
|
by the remote system for this BFD session. The value may
|
|
be zero(0) if the remote discriminator is not yet known
|
|
or if the session is in the down or adminDown(1) state."
|
|
REFERENCE
|
|
"Section 6.8.6, from Katz, D. and D. Ward, Bidirectional
|
|
Forwarding Detection (BFD), RFC 5880, June 2012."
|
|
::= { bfdSessEntry 5 }
|
|
|
|
bfdSessDestinationUdpPort OBJECT-TYPE
|
|
SYNTAX BfdCtrlDestPortNumberTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the destination UDP port number
|
|
used for this BFD session's control packets. The value
|
|
may be zero(0) if the session is in adminDown(1) state."
|
|
DEFVAL { 0 }
|
|
::= { bfdSessEntry 6 }
|
|
|
|
bfdSessSourceUdpPort OBJECT-TYPE
|
|
SYNTAX BfdCtrlSourcePortNumberTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the source UDP port number used
|
|
for this BFD session's control packets. The value may be
|
|
zero(0) if the session is in adminDown(1) state. Upon
|
|
creation of a new BFD session via this MIB, the value of
|
|
zero(0) specified would permit the implementation to
|
|
chose its own source port number."
|
|
DEFVAL { 0 }
|
|
::= { bfdSessEntry 7 }
|
|
|
|
bfdSessEchoSourceUdpPort OBJECT-TYPE
|
|
SYNTAX InetPortNumber
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the source UDP port number used for
|
|
this BFD session's echo packets. The value may be zero(0)
|
|
if the session is not running in the echo mode, or the
|
|
session is in adminDown(1) state. Upon creation of a new
|
|
BFD session via this MIB, the value of zero(0) would
|
|
permit the implementation to chose its own source port
|
|
number."
|
|
DEFVAL { 0 }
|
|
::= { bfdSessEntry 8 }
|
|
|
|
bfdSessAdminStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
stop(1),
|
|
start(2)
|
|
}
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A transition from 'stop' to 'start' will start
|
|
the BFD state machine for the session. The state
|
|
machine will have an initial state of down.
|
|
A transition from 'start' to 'stop' will cause
|
|
the BFD sesssion to be brought down to
|
|
adminDown(1). Care should be used in providing
|
|
write access to this object without adequate
|
|
authentication."
|
|
DEFVAL { 2 }
|
|
::= { bfdSessEntry 9 }
|
|
|
|
bfdSessState OBJECT-TYPE
|
|
SYNTAX BfdSessStateTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"BFD session state."
|
|
DEFVAL { 2 }
|
|
::= { bfdSessEntry 10 }
|
|
|
|
bfdSessRemoteHeardFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies status of BFD packet reception from
|
|
the remote system. Specifically, it is set to true(1) if
|
|
the local system is actively receiving BFD packets from the
|
|
remote system, and is set to false(2) if the local system
|
|
has not received BFD packets recently (within the detection
|
|
time) or if the local system is attempting to tear down
|
|
the BFD session."
|
|
REFERENCE
|
|
"Katz, D. and D. Ward, Bidirectional
|
|
Forwarding Detection (BFD), RFC 5880, June 2012."
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 11 }
|
|
|
|
bfdSessDiag OBJECT-TYPE
|
|
SYNTAX BfdDiagTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A diagnostic code specifying the local system's reason
|
|
for the last transition of the session from up(4)
|
|
to some other state."
|
|
::= { bfdSessEntry 12 }
|
|
|
|
bfdSessOperMode OBJECT-TYPE
|
|
SYNTAX BfdSessOperModeTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies current operating mode that BFD
|
|
session is operating in."
|
|
::= { bfdSessEntry 13 }
|
|
|
|
bfdSessDemandModeDesiredFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates that the local system's
|
|
desire to use Demand mode. Specifically, it is set
|
|
to true(1) if the local system wishes to use
|
|
Demand mode or false(2) if not"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 14 }
|
|
|
|
bfdSessControlPlaneIndepFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates that the local system's
|
|
ability to continue to function through a disruption of
|
|
the control plane. Specifically, it is set
|
|
to true(1) if the local system BFD implementation is
|
|
independent of the control plane. Otherwise, the
|
|
value is set to false(2)"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 15 }
|
|
|
|
bfdSessMultipointFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the Multipoint (M) bit for this
|
|
session. It is set to true(1) if Multipoint (M) bit is
|
|
set to 1. Otherwise, the value is set to false(2)"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 16 }
|
|
|
|
bfdSessInterface OBJECT-TYPE
|
|
SYNTAX InterfaceIndexOrZero
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains an interface index used to indicate
|
|
the interface which this BFD session is running on. This
|
|
value can be zero if there is no interface associated
|
|
with this BFD session."
|
|
::= { bfdSessEntry 17 }
|
|
|
|
bfdSessSrcAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies IP address type of the source IP
|
|
address of this BFD session. Only values unknown(0),
|
|
ipv4(1), ipv6(2), or ipv6z(4) have to be supported.
|
|
The value of unknown(0) is allowed only when the session
|
|
is singleHop(1) and the source IP address of this BFD
|
|
session is drived from the outgoing interface, or when
|
|
the BFD session is not associated with a specific
|
|
interface. If any other unsupported values are attempted
|
|
in a set operation, the agent MUST return an
|
|
inconsistentValue error."
|
|
::= { bfdSessEntry 18 }
|
|
|
|
bfdSessSrcAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the source IP address of this BFD
|
|
session."
|
|
::= { bfdSessEntry 19 }
|
|
|
|
bfdSessDstAddrType OBJECT-TYPE
|
|
SYNTAX InetAddressType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies IP address type of the neighboring IP
|
|
address which is being monitored with this BFD session.
|
|
Only values unknown(0), ipv4(1), ipv6(2), or ipv6z(4)
|
|
have to be supported. The value of unknown(0) is allowed
|
|
only when the session is singleHop(1) and the outgoing
|
|
interface is of type point-to-point, or when the BFD
|
|
session is not associated with a specific interface. If any
|
|
other unsupported values are attempted in a set operation,
|
|
the agent MUST return an inconsistentValue error."
|
|
::= { bfdSessEntry 20 }
|
|
|
|
bfdSessDstAddr OBJECT-TYPE
|
|
SYNTAX InetAddress
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the neighboring IP address which is
|
|
being monitored with this BFD session."
|
|
::= { bfdSessEntry 21 }
|
|
|
|
bfdSessGTSM OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Setting the value of this object to true(1) will enable GTSM
|
|
protection of the BFD session. GTSM MUST be enabled on a
|
|
singleHop(1) session if no authentication is in use."
|
|
REFERENCE
|
|
"RFC5082, The Generalized TTL Security Mechanism (GTSM).
|
|
RFC5881, Section 5"
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 22 }
|
|
|
|
bfdSessGTSMTTL OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..255)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is valid only when bfdSessGTSM protection is
|
|
enabled on the system. This object specifies the minimum
|
|
allowed TTL for received BFD control packets. For
|
|
singleHop(1) session, if GTSM protection is enabled,
|
|
this object SHOULD be set to maximum TTL allowed for
|
|
single hop. The value of zero(0) indicates that
|
|
bfdSessGTSM is disabled."
|
|
REFERENCE
|
|
"RFC5082, The Generalized TTL Security Mechanism (GTSM).
|
|
RFC5881, Section 5"
|
|
DEFVAL { 0 }
|
|
::= { bfdSessEntry 23 }
|
|
|
|
bfdSessDesiredMinTxInterval OBJECT-TYPE
|
|
SYNTAX BfdIntervalTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the minimum interval, in
|
|
microseconds, that the local system would like to use
|
|
when transmitting BFD Control packets. The value of
|
|
zero(0) is reserved, and should not be used."
|
|
REFERENCE
|
|
"Section 4.1 from Katz, D. and D. Ward, Bidirectional
|
|
Forwarding Detection (BFD), RFC 5880, June 2012."
|
|
::= { bfdSessEntry 24 }
|
|
|
|
bfdSessReqMinRxInterval OBJECT-TYPE
|
|
SYNTAX BfdIntervalTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the minimum interval, in
|
|
microseconds, between received BFD Control packets the
|
|
local system is capable of supporting. The value of
|
|
zero(0) can be specified when the transmitting system
|
|
does not want the remote system to send any periodic BFD
|
|
control packets."
|
|
REFERENCE
|
|
"Section 4.1 from Katz, D. and D. Ward, Bidirectional
|
|
Forwarding Detection (BFD), RFC 5880, June 2012."
|
|
::= { bfdSessEntry 25 }
|
|
|
|
bfdSessReqMinEchoRxInterval OBJECT-TYPE
|
|
SYNTAX BfdIntervalTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the minimum interval, in
|
|
microseconds, between received BFD Echo packets that this
|
|
system is capable of supporting. Value must be zero(0) if
|
|
this is a multihop BFD session."
|
|
::= { bfdSessEntry 26 }
|
|
|
|
bfdSessDetectMult OBJECT-TYPE
|
|
SYNTAX BfdMultiplierTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Detect time multiplier."
|
|
::= { bfdSessEntry 27 }
|
|
|
|
bfdSessNegotiatedInterval OBJECT-TYPE
|
|
SYNTAX BfdIntervalTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the negotiated interval, in
|
|
microseconds, that the local system is transmitting
|
|
BFD Control packets."
|
|
::= { bfdSessEntry 28 }
|
|
|
|
bfdSessNegotiatedEchoInterval OBJECT-TYPE
|
|
SYNTAX BfdIntervalTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the negotiated interval, in
|
|
microseconds, that the local system is transmitting
|
|
BFD echo packets. Value is expected to be zero if
|
|
the sessions is not running in echo mode."
|
|
::= { bfdSessEntry 29 }
|
|
|
|
bfdSessNegotiatedDetectMult OBJECT-TYPE
|
|
SYNTAX BfdMultiplierTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Detect time multiplier."
|
|
::= { bfdSessEntry 30 }
|
|
|
|
bfdSessAuthPresFlag OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates that the local system's
|
|
desire to use Authentication. Specifically, it is set
|
|
to true(1) if the local system wishes the session
|
|
to be authenticated or false(2) if not."
|
|
REFERENCE
|
|
"Sections 4.2 - 4.4 from Katz, D. and D. Ward,
|
|
Bidirectional Forwarding Detection (BFD), RFC 5880,
|
|
June 2012."
|
|
DEFVAL { false }
|
|
::= { bfdSessEntry 31 }
|
|
|
|
bfdSessAuthenticationType OBJECT-TYPE
|
|
SYNTAX BfdSessAuthenticationTypeTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Authentication Type used for this BFD session.
|
|
This field is valid only when the Authentication
|
|
Present bit is set. Max-access to this object as well as
|
|
other authentication related objects are set to
|
|
read-create in order to support management of a single
|
|
key ID at a time, key rotation is not handled. Key update
|
|
in practice must be done by atomic update using a set
|
|
containing all affected objects in the same varBindList
|
|
or otherwise risk the session dropping. Value -1
|
|
indicates that no authentication is in use for this
|
|
session."
|
|
REFERENCE
|
|
"Sections 4.2 - 4.4 from Katz, D. and D. Ward,
|
|
Bidirectional Forwarding Detection (BFD), RFC 5880,
|
|
June 2012."
|
|
DEFVAL { -1 }
|
|
::= { bfdSessEntry 32 }
|
|
|
|
bfdSessAuthenticationKeyID OBJECT-TYPE
|
|
SYNTAX Integer32 (-1 | 0..255)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The authentication key ID in use for this session. This
|
|
object permits multiple keys to be active simultaneously.
|
|
When bfdSessAuthPresFlag is false(2), then the value
|
|
of this object MUST be -1. The value -1 indicates that
|
|
no Authentication Key ID will be present in the optional
|
|
BFD Authentication Section."
|
|
REFERENCE
|
|
"Sections 4.2 - 4.4 from Katz, D. and D. Ward,
|
|
Bidirectional Forwarding Detection (BFD), RFC 5880,
|
|
June 2012."
|
|
DEFVAL { -1 }
|
|
::= { bfdSessEntry 33 }
|
|
|
|
bfdSessAuthenticationKey OBJECT-TYPE
|
|
SYNTAX BfdSessionAuthenticationKeyTC
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The authentication key. When the
|
|
bfdSessAuthenticationType is simplePassword(1), the value
|
|
of this object is the password present in the BFD packets.
|
|
|
|
When the bfdSessAuthentication type is one of the keyed
|
|
authentication types, this value is used in the
|
|
computation of the key present in the BFD authentication
|
|
packet."
|
|
REFERENCE
|
|
"Sections 4.2 - 4.4 from from Katz, D. and D. Ward,
|
|
Bidirectional Forwarding Detection (BFD), RFC 5880,
|
|
June 2012."
|
|
::= { bfdSessEntry 34 }
|
|
|
|
bfdSessStorageType OBJECT-TYPE
|
|
SYNTAX StorageType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates the storage type for this
|
|
object. Conceptual rows having the value
|
|
'permanent' need not allow write-access to any
|
|
columnar objects in the row."
|
|
::= { bfdSessEntry 35 }
|
|
|
|
bfdSessRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable is used to create, modify, and/or
|
|
delete a row in this table. When a row in this
|
|
table has a row in the active(1) state, no
|
|
objects in this row can be modified except the
|
|
bfdSessRowStatus and bfdSessStorageType."
|
|
::= { bfdSessEntry 36 }
|
|
|
|
-- BFD Session Performance Table
|
|
|
|
bfdSessPerfTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF BfdSessPerfEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table specifies BFD Session performance counters."
|
|
::= { bfdObjects 3 }
|
|
|
|
bfdSessPerfEntry OBJECT-TYPE
|
|
SYNTAX BfdSessPerfEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry in this table is created by a BFD-enabled node
|
|
for every BFD Session. bfdSessPerfDiscTime is used to
|
|
indicate potential discontinuity for all counter objects
|
|
in this table."
|
|
AUGMENTS { bfdSessEntry }
|
|
::= { bfdSessPerfTable 1 }
|
|
|
|
BfdSessPerfEntry ::= SEQUENCE {
|
|
bfdSessPerfCtrlPktIn Counter32,
|
|
bfdSessPerfCtrlPktOut Counter32,
|
|
bfdSessPerfCtrlPktDrop Counter32,
|
|
bfdSessPerfCtrlPktDropLastTime TimeStamp,
|
|
bfdSessPerfEchoPktIn Counter32,
|
|
bfdSessPerfEchoPktOut Counter32,
|
|
bfdSessPerfEchoPktDrop Counter32,
|
|
bfdSessPerfEchoPktDropLastTime TimeStamp,
|
|
bfdSessUpTime TimeStamp,
|
|
bfdSessPerfLastSessDownTime TimeStamp,
|
|
bfdSessPerfLastCommLostDiag BfdDiagTC,
|
|
bfdSessPerfSessUpCount Counter32,
|
|
bfdSessPerfDiscTime TimeStamp,
|
|
|
|
-- High Capacity Counters
|
|
bfdSessPerfCtrlPktInHC Counter64,
|
|
bfdSessPerfCtrlPktOutHC Counter64,
|
|
bfdSessPerfCtrlPktDropHC Counter64,
|
|
bfdSessPerfEchoPktInHC Counter64,
|
|
bfdSessPerfEchoPktOutHC Counter64,
|
|
bfdSessPerfEchoPktDropHC Counter64
|
|
}
|
|
|
|
-- Ed Note: should we add per-diag code counts here,
|
|
|
|
bfdSessPerfCtrlPktIn OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD control messages received for this
|
|
BFD session. This value MUST be equal to the least
|
|
significant 32 bits of bfdSessPerfCtrlPktInHC."
|
|
::= { bfdSessPerfEntry 1 }
|
|
|
|
bfdSessPerfCtrlPktOut OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD control messages sent for this BFD
|
|
session.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
significant 32 bits of bfdSessPerfCtrlPktOutHC
|
|
if supported, and MUST do so the rules spelled out in
|
|
RFC 2863."
|
|
|
|
::= { bfdSessPerfEntry 2 }
|
|
|
|
bfdSessPerfCtrlPktDrop OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD control messages received for this
|
|
session yet dropped for being invalid.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
significant 32 bits of bfdSessPerfCtrlPktDropHC
|
|
if supported, and MUST do so the rules spelled out in
|
|
RFC 2863."
|
|
::= { bfdSessPerfEntry 3 }
|
|
|
|
bfdSessPerfCtrlPktDropLastTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at
|
|
which received BFD control message for this session was
|
|
dropped. If no such up event exists, this object contains
|
|
a zero value."
|
|
::= { bfdSessPerfEntry 4 }
|
|
|
|
bfdSessPerfEchoPktIn OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD echo messages received for this
|
|
BFD session.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
significant 32 bits of bfdSessPerfEchoPktInHC if
|
|
supported, and MUST do so the rules spelled out in
|
|
RFC 2863."
|
|
::= { bfdSessPerfEntry 5 }
|
|
|
|
bfdSessPerfEchoPktOut OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD echo messages sent for this BFD
|
|
session.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfEchoPktOutHC if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 6 }
|
|
|
|
bfdSessPerfEchoPktDrop OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The total number of BFD echo messages received for this
|
|
session yet dropped for being invalid.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfEchoPktDropHC if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 7 }
|
|
|
|
bfdSessPerfEchoPktDropLastTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at
|
|
which received BFD echo message for this session was
|
|
dropped. If no such up event exists, this object contains
|
|
a zero value."
|
|
::= { bfdSessPerfEntry 8 }
|
|
|
|
bfdSessUpTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at which
|
|
the session came up. If no such up event exists this object
|
|
contains a zero value."
|
|
::= { bfdSessPerfEntry 9 }
|
|
|
|
bfdSessPerfLastSessDownTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at
|
|
which the last time communication was lost with the
|
|
neighbor. If no such down event exist this object
|
|
contains a zero value."
|
|
::= { bfdSessPerfEntry 10 }
|
|
|
|
bfdSessPerfLastCommLostDiag OBJECT-TYPE
|
|
SYNTAX BfdDiagTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD diag code for the last time communication was lost
|
|
with the neighbor. If no such down event exists this object
|
|
contains a zero value."
|
|
::= { bfdSessPerfEntry 11 }
|
|
|
|
bfdSessPerfSessUpCount OBJECT-TYPE
|
|
SYNTAX Counter32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of times this session has gone into the Up
|
|
state since the system last rebooted."
|
|
::= { bfdSessPerfEntry 12 }
|
|
|
|
bfdSessPerfDiscTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of sysUpTime on the most recent occasion at
|
|
which any one or more of the session counters suffered
|
|
a discontinuity.
|
|
|
|
The relevant counters are the specific instances associated
|
|
with this BFD session of any Counter32 object contained in
|
|
the BfdSessPerfTable. If no such discontinuities have
|
|
occurred since the last re-initialization of the local
|
|
management subsystem, then this object contains a zero
|
|
value."
|
|
::= { bfdSessPerfEntry 13 }
|
|
|
|
bfdSessPerfCtrlPktInHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of BFD control
|
|
messages received for this BFD session.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfCtrlPktInHC if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 14 }
|
|
|
|
bfdSessPerfCtrlPktOutHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of BFD control
|
|
messages transmitted for this BFD session.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfCtrlPktOut if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 15 }
|
|
|
|
bfdSessPerfCtrlPktDropHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of BFD control
|
|
messages received for this BFD session yet dropped for
|
|
being invalid.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfCtrlPktDrop if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 16 }
|
|
|
|
bfdSessPerfEchoPktInHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of BFD echo
|
|
messages received for this BFD session.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfEchoPktIn if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 17 }
|
|
|
|
bfdSessPerfEchoPktOutHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of BFD echo
|
|
messages transmitted for this BFD session.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfEchoPktOut if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 18 }
|
|
|
|
bfdSessPerfEchoPktDropHC OBJECT-TYPE
|
|
SYNTAX Counter64
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents the total number of BFD echo
|
|
messages received for this BFD session yet dropped
|
|
for being invalid.
|
|
|
|
It MUST be equal to the least significant 32 bits of
|
|
bfdSessPerfEchoPktDrop if supported, and MUST do so
|
|
the rules spelled out in RFC 2863."
|
|
::= { bfdSessPerfEntry 19 }
|
|
|
|
-- BFD Session Discriminator Mapping Table
|
|
|
|
bfdSessDiscMapTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF BfdSessDiscMapEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Discriminator Mapping Table maps a
|
|
local discriminator value to associated BFD session's
|
|
BfdSessIndexTC used in the bfdSessionTable."
|
|
::= { bfdObjects 4 }
|
|
|
|
bfdSessDiscMapEntry OBJECT-TYPE
|
|
SYNTAX BfdSessDiscMapEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session Discriminator Map Entry describes
|
|
BFD session that is mapped to this BfdSessIndexTC."
|
|
INDEX { bfdSessDiscriminator }
|
|
::= { bfdSessDiscMapTable 1 }
|
|
|
|
BfdSessDiscMapEntry ::= SEQUENCE {
|
|
bfdSessDiscMapIndex BfdSessIndexTC,
|
|
bfdSessDiscMapStorageType StorageType,
|
|
bfdSessDiscMapRowStatus RowStatus
|
|
}
|
|
|
|
bfdSessDiscMapIndex OBJECT-TYPE
|
|
SYNTAX BfdSessIndexTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the BfdSessIndexTC referred to by
|
|
the indices of this row. In essence, a mapping is
|
|
provided between these indexes and the BfdSessTable."
|
|
::= { bfdSessDiscMapEntry 1 }
|
|
|
|
bfdSessDiscMapStorageType OBJECT-TYPE
|
|
SYNTAX StorageType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates the storage type for this
|
|
object. Conceptual rows having the value
|
|
'permanent' need not allow write-access to any
|
|
columnar objects in the row."
|
|
::= { bfdSessDiscMapEntry 2 }
|
|
|
|
bfdSessDiscMapRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable is used to create, modify, and/or
|
|
delete a row in this table. When a row in this
|
|
table has a row in the active(1) state, no
|
|
objects in this row can be modified except the
|
|
bfdSessDiscMapRowStatus and bfdSessDiscMapStorageType."
|
|
::= { bfdSessDiscMapEntry 3 }
|
|
|
|
-- BFD Session IP Mapping Table
|
|
|
|
bfdSessIpMapTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF BfdSessIpMapEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session IP Mapping Table maps given
|
|
bfdSessInterface, bfdSessSrcAddrType, bfdSessSrcAddr,
|
|
bfdSessDstAddrType and bfdSessDstAddr
|
|
to an associated BFD session's BfdSessIndexTC used in
|
|
the bfdSessionTable."
|
|
::= { bfdObjects 5 }
|
|
|
|
bfdSessIpMapEntry OBJECT-TYPE
|
|
SYNTAX BfdSessIpMapEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The BFD Session IP Map Entry describes
|
|
BFD session that is mapped to this BfdSessIndexTC."
|
|
INDEX {
|
|
bfdSessInterface,
|
|
bfdSessSrcAddrType,
|
|
bfdSessSrcAddr,
|
|
bfdSessDstAddrType,
|
|
bfdSessDstAddr
|
|
}
|
|
::= { bfdSessIpMapTable 1 }
|
|
|
|
BfdSessIpMapEntry ::= SEQUENCE {
|
|
bfdSessIpMapIndex BfdSessIndexTC,
|
|
bfdSessIpMapStorageType StorageType,
|
|
bfdSessIpMapRowStatus RowStatus
|
|
}
|
|
|
|
bfdSessIpMapIndex OBJECT-TYPE
|
|
SYNTAX BfdSessIndexTC
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the BfdSessIndexTC referred to by
|
|
the indexes of this row. In essence, a mapping is
|
|
provided between these indexes and the BfdSessTable."
|
|
::= { bfdSessIpMapEntry 1 }
|
|
|
|
bfdSessIpMapStorageType OBJECT-TYPE
|
|
SYNTAX StorageType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable indicates the storage type for this
|
|
object. Conceptual rows having the value
|
|
'permanent' need not allow write-access to any
|
|
columnar objects in the row."
|
|
::= { bfdSessIpMapEntry 2 }
|
|
|
|
bfdSessIpMapRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This variable is used to create, modify, and/or
|
|
delete a row in this table. When a row in this
|
|
table has a row in the active(1) state, no
|
|
objects in this row can be modified except the
|
|
bfdSessIpMapRowStatus and bfdSessIpMapStorageType."
|
|
::= { bfdSessIpMapEntry 3 }
|
|
|
|
-- Notification Configuration
|
|
|
|
bfdSessUp NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
bfdSessDiag, -- low range value
|
|
bfdSessDiag -- high range value
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is generated when the
|
|
bfdSessState object for one or more contiguous
|
|
entries in bfdSessTable are about to enter the up(4)
|
|
state from some other state. The included values of
|
|
bfdSessDiag MUST both be set equal to this
|
|
new state (i.e: up(4)). The two instances of
|
|
bfdSessDiag in this notification indicate the range
|
|
of indexes that are affected. Note that all the indexes
|
|
of the two ends of the range can be derived from the
|
|
instance identifiers of these two objects. For the
|
|
cases where a contiguous range of sessions
|
|
have transitioned into the up(4) state at roughly
|
|
the same time, the device SHOULD issue a single
|
|
notification for each range of contiguous indexes in
|
|
an effort to minimize the emission of a large number
|
|
of notifications. If a notification has to be
|
|
issued for just a single bfdSessEntry, then
|
|
the instance identifier (and values) of the two
|
|
bfdSessDiag objects MUST be the identical."
|
|
::= { bfdNotifications 1 }
|
|
|
|
bfdSessDown NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
bfdSessDiag, -- low range value
|
|
bfdSessDiag -- high range value
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This notification is generated when the
|
|
bfdSessState object for one or more contiguous
|
|
entries in bfdSessTable are about to enter the down(2)
|
|
or adminDown(1) states from some other state. The included
|
|
values of bfdSessDiag MUST both be set equal to this new
|
|
state (i.e: down(2) or adminDown(1)). The two instances
|
|
of bfdSessDiag in this notification indicate the range
|
|
of indexes that are affected. Note that all the indexes
|
|
of the two ends of the range can be derived from the
|
|
instance identifiers of these two objects. For
|
|
cases where a contiguous range of sessions
|
|
have transitioned into the down(2) or adminDown(1) states
|
|
at roughly the same time, the device SHOULD issue a single
|
|
notification for each range of contiguous indexes in
|
|
an effort to minimize the emission of a large number
|
|
of notifications. If a notification has to be
|
|
issued for just a single bfdSessEntry, then
|
|
the instance identifier (and values) of the two
|
|
bfdSessDiag objects MUST be the identical."
|
|
::= { bfdNotifications 2 }
|
|
|
|
-- Ed Note: We need to add notification for changes
|
|
-- when the two ends automatically negotiate to a new detection time
|
|
-- value or when detection multiplier changes.
|
|
|
|
|
|
-- Module compliance.
|
|
|
|
bfdGroups
|
|
OBJECT IDENTIFIER ::= { bfdConformance 1 }
|
|
|
|
bfdCompliances
|
|
OBJECT IDENTIFIER ::= { bfdConformance 2 }
|
|
|
|
-- Compliance requirement for fully compliant implementations.
|
|
|
|
bfdModuleFullCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Compliance statement for agents that provide full
|
|
support for the BFD-MIB module. Such devices can
|
|
then be monitored and also be configured using
|
|
this MIB module."
|
|
|
|
MODULE -- This module.
|
|
|
|
MANDATORY-GROUPS {
|
|
bfdSessionGroup,
|
|
bfdSessionReadOnlyGroup,
|
|
bfdSessionPerfGroup,
|
|
bfdNotificationGroup
|
|
}
|
|
|
|
GROUP bfdSessionPerfHCGroup
|
|
DESCRIPTION "This group is mandatory for all systems that
|
|
are able to support the Counter64 date type."
|
|
|
|
OBJECT bfdSessSrcAddrType
|
|
SYNTAX InetAddressType { unknown(0), ipv4(1),
|
|
ipv6(2), ipv6z(4) }
|
|
DESCRIPTION "Only unknown(0), ipv4(1), ipv6(2) and ipv6z(4)
|
|
support are required."
|
|
|
|
OBJECT bfdSessSrcAddr
|
|
SYNTAX InetAddress (SIZE (0|4|16|20))
|
|
DESCRIPTION "An implementation is only required to support
|
|
unknown(0), ipv4(1), ipv6(2) and ipv6z(4) sizes."
|
|
|
|
OBJECT bfdSessDstAddrType
|
|
SYNTAX InetAddressType { unknown(0), ipv4(1),
|
|
ipv6(2), ipv6z(4) }
|
|
DESCRIPTION "Only unknown(0), ipv4(1), ipv6(2) and ipv6z(4)
|
|
support are required."
|
|
|
|
OBJECT bfdSessDstAddr
|
|
SYNTAX InetAddress (SIZE (0|4|16|20))
|
|
DESCRIPTION "An implementation is only required to support
|
|
unknown(0), ipv4(1), ipv6(2) and ipv6z(4) sizes."
|
|
|
|
OBJECT bfdSessRowStatus
|
|
SYNTAX RowStatus { active(1), notInService(2) }
|
|
WRITE-SYNTAX RowStatus { active(1), notInService(2),
|
|
createAndGo(4), destroy(6) }
|
|
DESCRIPTION "Support for createAndWait and notReady is not
|
|
required."
|
|
|
|
OBJECT bfdSessDiscMapRowStatus
|
|
SYNTAX RowStatus { active(1), notInService(2) }
|
|
WRITE-SYNTAX RowStatus { active(1), notInService(2),
|
|
createAndGo(4), destroy(6) }
|
|
DESCRIPTION "Support for createAndWait and notReady is not
|
|
required."
|
|
|
|
|
|
OBJECT bfdSessIpMapRowStatus
|
|
SYNTAX RowStatus { active(1), notInService(2) }
|
|
WRITE-SYNTAX RowStatus { active(1), notInService(2),
|
|
createAndGo(4), destroy(6) }
|
|
DESCRIPTION "Support for createAndWait and notReady is not
|
|
required."
|
|
|
|
::= { bfdCompliances 1 }
|
|
|
|
bfdModuleReadOnlyCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Compliance requirement for implementations that only
|
|
provide read-only support for BFD-MIB. Such devices
|
|
can then be monitored but cannot be configured using
|
|
this MIB module."
|
|
|
|
MODULE -- This module.
|
|
|
|
MANDATORY-GROUPS {
|
|
bfdSessionGroup,
|
|
bfdSessionReadOnlyGroup,
|
|
bfdSessionPerfGroup,
|
|
bfdNotificationGroup
|
|
}
|
|
|
|
GROUP bfdSessionPerfHCGroup
|
|
DESCRIPTION "This group is mandatory for all systems that
|
|
are able to support the Counter64 date type."
|
|
|
|
OBJECT bfdSessVersionNumber
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessType
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessDestinationUdpPort
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessSourceUdpPort
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessEchoSourceUdpPort
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessAdminStatus
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessOperMode
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessDemandModeDesiredFlag
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessControlPlaneIndepFlag
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessMultipointFlag
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessInterface
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessSrcAddrType
|
|
SYNTAX InetAddressType { unknown(0), ipv4(1),
|
|
ipv6(2), ipv6z(4) }
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Only unknown(0), ipv4(1), ipv6(2) and ipv6z(4)
|
|
support are required."
|
|
|
|
OBJECT bfdSessSrcAddr
|
|
SYNTAX InetAddress (SIZE (0|4|16|20))
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "An implementation is only required to support
|
|
unknown(0), ipv4(1), ipv6(2) and ipv6z(4) sizes."
|
|
|
|
OBJECT bfdSessDstAddrType
|
|
SYNTAX InetAddressType { unknown(0), ipv4(1),
|
|
ipv6(2), ipv6z(4) }
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Only unknown(0), ipv4(1), ipv6(2) and ipv6z(4)
|
|
support are required."
|
|
|
|
OBJECT bfdSessDstAddr
|
|
SYNTAX InetAddress (SIZE (0|4|16|20))
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "An implementation is only required to support
|
|
unknown(0), ipv4(1), ipv6(2) and ipv6z(4) sizes."
|
|
|
|
OBJECT bfdSessGTSM
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessGTSMTTL
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessDesiredMinTxInterval
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessReqMinRxInterval
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessReqMinEchoRxInterval
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessDetectMult
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessAuthPresFlag
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessAuthenticationType
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessAuthenticationKeyID
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessAuthenticationKey
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessStorageType
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessRowStatus
|
|
SYNTAX RowStatus { active(1) }
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessDiscMapStorageType
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessDiscMapRowStatus
|
|
SYNTAX RowStatus { active(1) }
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessIpMapStorageType
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
OBJECT bfdSessIpMapRowStatus
|
|
SYNTAX RowStatus { active(1) }
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION "Write access is not required."
|
|
|
|
::= { bfdCompliances 2 }
|
|
|
|
-- Units of conformance.
|
|
|
|
bfdSessionGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
bfdAdminStatus,
|
|
bfdSessNotificationsEnable,
|
|
bfdSessVersionNumber,
|
|
bfdSessType,
|
|
bfdSessDestinationUdpPort,
|
|
bfdSessSourceUdpPort,
|
|
bfdSessEchoSourceUdpPort,
|
|
bfdSessAdminStatus,
|
|
bfdSessOperMode,
|
|
bfdSessDemandModeDesiredFlag,
|
|
bfdSessControlPlaneIndepFlag,
|
|
bfdSessMultipointFlag,
|
|
bfdSessInterface,
|
|
bfdSessSrcAddrType,
|
|
bfdSessSrcAddr,
|
|
bfdSessDstAddrType,
|
|
bfdSessDstAddr,
|
|
bfdSessGTSM,
|
|
bfdSessGTSMTTL,
|
|
bfdSessDesiredMinTxInterval,
|
|
bfdSessReqMinRxInterval,
|
|
bfdSessReqMinEchoRxInterval,
|
|
bfdSessDetectMult,
|
|
bfdSessAuthPresFlag,
|
|
bfdSessAuthenticationType,
|
|
bfdSessAuthenticationKeyID,
|
|
bfdSessAuthenticationKey,
|
|
bfdSessStorageType,
|
|
bfdSessRowStatus,
|
|
bfdSessDiscMapStorageType,
|
|
bfdSessDiscMapRowStatus,
|
|
bfdSessIpMapStorageType,
|
|
bfdSessIpMapRowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Collection of objects needed for BFD sessions."
|
|
::= { bfdGroups 1 }
|
|
|
|
bfdSessionReadOnlyGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
bfdSessDiscriminator,
|
|
bfdSessRemoteDiscr,
|
|
bfdSessState,
|
|
bfdSessRemoteHeardFlag,
|
|
bfdSessDiag,
|
|
bfdSessNegotiatedInterval,
|
|
bfdSessNegotiatedEchoInterval,
|
|
bfdSessNegotiatedDetectMult,
|
|
bfdSessDiscMapIndex,
|
|
bfdSessIpMapIndex
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Collection of read-only objects needed for BFD sessions."
|
|
::= { bfdGroups 2 }
|
|
|
|
bfdSessionPerfGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
bfdSessPerfCtrlPktIn,
|
|
bfdSessPerfCtrlPktOut,
|
|
bfdSessPerfCtrlPktDrop,
|
|
bfdSessPerfCtrlPktDropLastTime,
|
|
bfdSessPerfEchoPktIn,
|
|
bfdSessPerfEchoPktOut,
|
|
bfdSessPerfEchoPktDrop,
|
|
bfdSessPerfEchoPktDropLastTime,
|
|
bfdSessUpTime,
|
|
bfdSessPerfLastSessDownTime,
|
|
bfdSessPerfLastCommLostDiag,
|
|
bfdSessPerfSessUpCount,
|
|
bfdSessPerfDiscTime
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Collection of objects needed to monitor the
|
|
performance of BFD sessions."
|
|
::= { bfdGroups 3 }
|
|
|
|
bfdSessionPerfHCGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
bfdSessPerfCtrlPktInHC,
|
|
bfdSessPerfCtrlPktOutHC,
|
|
bfdSessPerfCtrlPktDropHC,
|
|
bfdSessPerfEchoPktInHC,
|
|
bfdSessPerfEchoPktOutHC,
|
|
bfdSessPerfEchoPktDropHC
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Collection of objects needed to monitor the
|
|
performance of BFD sessions for which the
|
|
values of bfdSessPerfPktIn, bfdSessPerfPktOut
|
|
wrap around too quickly."
|
|
::= { bfdGroups 4 }
|
|
|
|
bfdNotificationGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS {
|
|
bfdSessUp,
|
|
bfdSessDown
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set of notifications implemented in this
|
|
module."
|
|
::= { bfdGroups 5 }
|
|
|
|
END
|