WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/qtech/QTECH-OSPF-MIB

2957 lines
100 KiB
Plaintext
Raw Blame History

-- *****************************************************************
-- QTECH-OSPF-MIB.mib: Qtech Ospf MIB file
--
-- November 2002, ChenXingBin
--
-- Copyright (c) 2002 by Qtech Networks Co.,Ltd.
-- All rights reserved.
--
-- *****************************************************************
--
QTECH-OSPF-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
TimeTicks,
IpAddress,
Unsigned32,
Gauge32,
Counter32
FROM SNMPv2-SMI
TruthValue,
RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF
ConfigStatus
FROM QTECH-TC
EnabledStatus
FROM P-BRIDGE-MIB
AreaID,
Status,
PositiveInteger,
DesignatedRouterPriority,
RouterID,
HelloRange
FROM OSPF-MIB
qtechMgmt
FROM QTECH-SMI;
qtechOspfMIB MODULE-IDENTITY
LAST-UPDATED "200211200000Z"
ORGANIZATION "Qtech Networks Co.,Ltd."
CONTACT-INFO
"
Tel: 4008-111-000
E-mail: service@qtech.com.cn"
DESCRIPTION
"This module defines qtech Ospf mibs."
REVISION "200211200000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { qtechMgmt 30}
qtechOspfMIBObjects OBJECT IDENTIFIER ::= { qtechOspfMIB 1 }
-- general mib
qtechOspfGeneralMibsGroup OBJECT IDENTIFIER ::= { qtechOspfMIBObjects 1 }
--Minimum LSA interval
qtechOspfMiniLsaInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum LSA interval that the two LSA generate."
::={ qtechOspfGeneralMibsGroup 1 }
--Minimum LSA arrival
qtechOspfMiniLsaArrival OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum LSA Interval of the two LSA arrival."
::={ qtechOspfGeneralMibsGroup 2 }
--Number of areas in this router
qtechOspfAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of areas in this router"
::={ qtechOspfGeneralMibsGroup 3 }
qtechOspfNormalAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of normal areas in this router"
::={ qtechOspfGeneralMibsGroup 4}
qtechOspfStubAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of stub areas in this router"
::={ qtechOspfGeneralMibsGroup 5 }
qtechOspfNssaAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of nssa areas in this router"
::={ qtechOspfGeneralMibsGroup 6 }
qtechOspfSpfDelay OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Ospf Spf shedule time, an integer from 0 to 65535. The default is 5
seconds,0 means no delay."
DEFVAL {5}
::={ qtechOspfGeneralMibsGroup 7 }
qtechOspfSpfHoldTime OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"hold time between two Spfs.an integer from 0 to 65535. The default is
10 seconds; 0 means no delay."
DEFVAL {10}
::={ qtechOspfGeneralMibsGroup 8 }
qtechOspfAutoCostRefBandWidthRef OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set AutoCost bandwidth referenc value in unit of Mbits.
Setting this value to 0 indicate that disable the feature of
autocost bandwidth referenc."
DEFVAL {100}
::={ qtechOspfGeneralMibsGroup 9 }
qtechOspfLsaGroupPacing OBJECT-TYPE
SYNTAX Unsigned32(10..1800)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"set the group pacing of LSAs."
DEFVAL {240}
::={ qtechOspfGeneralMibsGroup 10}
qtechOspfInterDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set inter-area distance."
DEFVAL {110}
::= { qtechOspfGeneralMibsGroup 11 }
qtechOspfIntraDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set intra-area distance."
DEFVAL {110}
::= { qtechOspfGeneralMibsGroup 12 }
qtechOspfExternDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set extern distance."
DEFVAL {110}
::= { qtechOspfGeneralMibsGroup 13 }
--LogAdjChangeNotify
qtechOspfLogAdjChangeNotify OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"if enabled status is setted,
Send syslog message when a neighbor state changes."
DEFVAL {enabled}
::= { qtechOspfGeneralMibsGroup 14 }
qtechOspfPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The qtechOspfIfPassiveStatus of a interface equal to this object value
when this interface is created. If you change this object value to 'enabled'
or 'disabled'all interfaces which have exist will also change their
qtechOspfIfPassiveStatus to 'enabled' or 'disabled'."
DEFVAL { disabled }
::={ qtechOspfGeneralMibsGroup 15 }
qtechOspfRFC1583Compatibility OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the preference rules used in calculating AS external routes
(RFC2328 Section 16.4) when choosing among multiple AS-external-LSAs
advertising the same destination. When set to 'enabled', the preference
rules remain those specified by RFC 1583 ([Ref9]). When set
to 'disabled', the preference rules are those stated in
'RFC2328 Section 16.4.1' which prevent routing loops when AS-
external-LSAs for the same destination have been originated
from different areas. Set to 'enabled' by default."
REFERENCE
"OSPF Version 2(RFC2328), C.1 Global parameters"
DEFVAL { enabled }
::={ qtechOspfGeneralMibsGroup 16 }
qtechOspfRouteRedisDefMetricVal OBJECT-TYPE
SYNTAX Unsigned32(1..16777214)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this value is setted,Cause the current routing protocol(ospf)
to use the same metricvalue for all redistributed routes (BGP, RIP, and OSPF)."
DEFVAL {20}
::= { qtechOspfGeneralMibsGroup 17}
qtechOspfAdminiDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"ospf Administrative distance."
DEFVAL {110}
::= { qtechOspfGeneralMibsGroup 18}
--table mib
--qtechOspfAreaTable
qtechOspfAreaTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfAreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the configured parame-
ters and cumulative statistics of the router's
attached areas.This table is superset of ospfAreaTable"
::= { qtechOspfMIBObjects 2}
qtechOspfAreaEntry OBJECT-TYPE
SYNTAX QtechOspfAreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The entry of qtechOspfAreaTable."
INDEX { qtechOspfAreaId}
::= { qtechOspfAreaTable 1 }
QtechOspfAreaEntry ::=
SEQUENCE {
qtechOspfAreaId
AreaID,
qtechOspfAuthType
INTEGER,
qtechOspfImportAsExtern
INTEGER,
qtechOspfSpfRuns
Counter32,
qtechOspfAreaBdrRtrCount
Gauge32,
qtechOspfAsBdrRtrCount
Gauge32,
qtechOspfAreaLsaCount
Gauge32,
qtechOspfAreaLsaCksumSum
Unsigned32,
qtechOspfAreaSummary
INTEGER,
qtechOspfAreaStatus
RowStatus,
-- extend parts
qtechOspfAreaInterfaceNum
Unsigned32,
qtechOspfAreaNssaIsRedistribution
TruthValue,
qtechOspfAreaNssaIsDefInfoOriginate
TruthValue
}
qtechOspfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying an area.
Area ID 0.0.0.0 is used for the OSPF backbone."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { qtechOspfAreaEntry 1 }
qtechOspfAuthType OBJECT-TYPE
SYNTAX INTEGER{
none(0),
simplePassword(1),
md5 (2)
-- reserved for specification by IANA (> 2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication type specified for an area.
Additional authentication types may be assigned
locally on a per Area basis."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { qtechOspfAreaEntry 2 }
qtechOspfImportAsExtern OBJECT-TYPE
SYNTAX INTEGER {
importExternal (1), --normal area
importNoExternal (2), -- stub area
importNssa (3) -- NSSA area
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The area's support for importing AS external
link- state advertisements."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
DEFVAL { importExternal }
::= { qtechOspfAreaEntry 3 }
qtechOspfSpfRuns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that the intra-area route
table has been calculated using this area's
link-state database. This is typically done
using Dijkstra's algorithm."
::= { qtechOspfAreaEntry 4 }
qtechOspfAreaBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of area border routers reach-
able within this area. This is initially zero,
and is calculated in each SPF Pass."
::= { qtechOspfAreaEntry 5 }
qtechOspfAsBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Autonomous System border
routers reachable within this area. This is
initially zero, and is calculated in each SPF
Pass."
::= { qtechOspfAreaEntry 6 }
qtechOspfAreaLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of link-state advertisements
in this area's link-state database, excluding
AS External LSA's."
::= { qtechOspfAreaEntry 7 }
qtechOspfAreaLsaCksumSum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32-bit unsigned sum of the link-state ad-
vertisements' LS checksums contained in this
area's link-state database. This sum excludes
external (LS type 5) link-state advertisements.
The sum can be used to determine if there has
been a change in a router's link state data-
base, and to compare the link-state database of
two routers."
DEFVAL { 0 }
::= { qtechOspfAreaEntry 8 }
qtechOspfAreaSummary OBJECT-TYPE
SYNTAX INTEGER {
noAreaSummary (1),
sendAreaSummary (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable ospfAreaSummary controls the im-
port of summary LSAs into stub areas. It has
no effect on other areas.
If it is noAreaSummary, the router will neither
originate nor propagate summary LSAs into the
stub area. It will rely entirely on its de-
fault route.
If it is sendAreaSummary, the router will both
summarize and propagate summary LSAs."
DEFVAL { sendAreaSummary }
::= { qtechOspfAreaEntry 9 }
qtechOspfAreaStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { qtechOspfAreaEntry 10 }
qtechOspfAreaInterfaceNum OBJECT-TYPE --for command "show
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the interface number of this area"
::= { qtechOspfAreaEntry 11 }
qtechOspfAreaNssaIsRedistribution OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" if it's disabled , when the router is an NSSA ABR and
you want the redistribute command to import routes into normal
areas, but not into the NSSA,
this field is vaild for nssa area"
DEFVAL {true}
::= { qtechOspfAreaEntry 12}
qtechOspfAreaNssaIsDefInfoOriginate OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"if it's enabled it meaning that on an ABR to allow
importing type 7 LSAs into the NSSA,
this field is valid for nssa area"
DEFVAL {false}
::= { qtechOspfAreaEntry 13}
--network address scope table
qtechOspfAddressScopeTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfAddressScopeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Define an interface on which OSPF runs and the area ID for that
interface. You can use the wildcard-mask to use a single
command to define one or more multiple interfaces to be
associated with a specific OSPF area. "
::= { qtechOspfMIBObjects 3 }
qtechOspfAddressScopeEntry OBJECT-TYPE
SYNTAX QtechOspfAddressScopeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry define an scope of address for ospf routing."
INDEX { qtechOspfNetWorkAreaID,qtechOspfNetWorkAddress, qtechOspfNetWorkMask}
::= { qtechOspfAddressScopeTable 1 }
QtechOspfAddressScopeEntry ::=
SEQUENCE {
qtechOspfNetWorkAreaID
IpAddress,
qtechOspfNetWorkAddress
IpAddress,
qtechOspfNetWorkMask
IpAddress,
qtechOspfNetWorkStatus
RowStatus
}
qtechOspfNetWorkAreaID OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"area ID"
::= { qtechOspfAddressScopeEntry 1 }
qtechOspfNetWorkAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Routing for Networks Ipaddress"
::= { qtechOspfAddressScopeEntry 2 }
qtechOspfNetWorkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Routing for Networks mask"
::= { qtechOspfAddressScopeEntry 3 }
qtechOspfNetWorkStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" when this value is destroy,the
entry will be deleted"
::= { qtechOspfAddressScopeEntry 4 }
-- The Ospf Interface Configuration Table
qtechOspfIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Interface Table describes the interfaces
from the viewpoint of OSPF."
REFERENCE
"ospfIfTable in rfc1850"
::= { qtechOspfMIBObjects 4 }
qtechOspfIfEntry OBJECT-TYPE
SYNTAX QtechOspfIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Interface Entry describes one inter-
face configuration of OSPF."
INDEX { qtechOspfIfIpAddress, qtechOspfAddressLessIf }
::= { qtechOspfIfTable 1 }
QtechOspfIfEntry ::=
SEQUENCE {
qtechOspfIfIpAddress
IpAddress,
qtechOspfAddressLessIf
Unsigned32,
qtechOspfIfAreaId
AreaID,
qtechOspfIfType
INTEGER,
qtechOspfIfAdminStat
Status,
qtechOspfIfRtrPriority
DesignatedRouterPriority,
qtechOspfIfTransitDelay
Unsigned32,
qtechOspfIfRetransInterval
Unsigned32,
qtechOspfIfHelloInterval
HelloRange,
qtechOspfIfRtrDeadInterval
PositiveInteger,
qtechOspfIfPollInterval
PositiveInteger,
qtechOspfIfState
INTEGER,
qtechOspfIfDesignatedRouter
IpAddress,
qtechOspfIfBackupDesignatedRouter
IpAddress,
qtechOspfIfEvents
Counter32,
qtechOspfIfAuthType
INTEGER,
qtechOspfIfAuthKey
OCTET STRING,
qtechOspfIfStatus
RowStatus,
qtechOspfIfMulticastForwarding
INTEGER,
qtechOspfIfDemand
TruthValue,
qtechOspfIfDatabaseFilterAllOut
EnabledStatus,
qtechOspfIfDesignateRouterId
IpAddress,
qtechOspfIfBackupDesignateRouterId
IpAddress,
qtechOspfIfWaitInternal
TimeTicks,
qtechOspfIfPassiveStatus
EnabledStatus,
qtechOspfIfCurrentUsedMd5AuthKeyId
Unsigned32
}
qtechOspfIfIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of this OSPF interface."
::= { qtechOspfIfEntry 1 }
qtechOspfAddressLessIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP Addresses, and the corresponding value of
ifIndex for interfaces having no IP Address."
::= { qtechOspfIfEntry 2 }
qtechOspfIfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0.0.0.0 is used for the OSPF backbone."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { qtechOspfIfEntry 3 }
qtechOspfIfType OBJECT-TYPE
SYNTAX INTEGER {
broadcast (1),
nbma (2),
pointToPoint (3),
pointToMultipoint (5),
loopback(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The OSPF interface type.
By way of a default, this field may be intuited
from the corresponding value of ifType. Broad-
cast LANs, such as Ethernet and IEEE 802.5,
take the value 'broadcast', X.25 and similar
technologies take the value 'nbma', and links
that are definitively point to point take the
value 'pointToPoint'."
::= { qtechOspfIfEntry 4 }
qtechOspfIfAdminStat OBJECT-TYPE
SYNTAX Status
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The OSPF interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to OSPF."
::= { qtechOspfIfEntry 5 }
qtechOspfIfRtrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not eligi-
ble to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker."
DEFVAL { 1 }
::= { qtechOspfIfEntry 6 }
qtechOspfIfTransitDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link state update packet over this
interface."
DEFVAL { 1 }
::= { qtechOspfIfEntry 7 }
qtechOspfIfRetransInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets."
DEFVAL { 5 }
::= { qtechOspfIfEntry 8 }
qtechOspfIfHelloInterval OBJECT-TYPE
SYNTAX HelloRange
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for all
routers attached to a common network."
DEFVAL { 10 }
::= { qtechOspfIfEntry 9 }
qtechOspfIfRtrDeadInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for all routers attached
to a common network."
DEFVAL { 40 }
::= { qtechOspfIfEntry 10 }
qtechOspfIfPollInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The larger time interval, in seconds, between
the Hello packets sent to an inactive non-
broadcast multi- access neighbor."
::= { qtechOspfIfEntry 11 }
qtechOspfIfState OBJECT-TYPE
SYNTAX INTEGER {
down (1),
loopback (2),
waiting (3),
pointToPoint (4),
designatedRouter (5),
backupDesignatedRouter (6),
otherDesignatedRouter (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The OSPF Interface State."
DEFVAL { down }
::= { qtechOspfIfEntry 12 }
qtechOspfIfDesignatedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP Address of the interface which connected the local router in
the Designated Router."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { qtechOspfIfEntry 13 }
qtechOspfIfBackupDesignatedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP Address of the interface which connected the local router in
the Backup Designated Router."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { qtechOspfIfEntry 14 }
qtechOspfIfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this OSPF interface has
changed its state, or an error has occurred."
::= { qtechOspfIfEntry 15 }
qtechOspfIfAuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Authentication Key. If the Area's Author-
ization Type is simplePassword, and the key
length is shorter than 8 octets, the agent will
left adjust and zero fill to 8 octets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, qtechOspfIfAuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0
::= { qtechOspfIfEntry 16 }
qtechOspfIfStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value will be active(1) always."
::= { qtechOspfIfEntry 17 }
qtechOspfIfMulticastForwarding OBJECT-TYPE
SYNTAX INTEGER {
blocked (1), -- no multicast forwarding
multicast (2), -- using multicast address
unicast (3) -- to each OSPF neighbor
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link uni-
casts. Data link multicasting is not meaning-
ful on point to point and NBMA interfaces, and
setting ospfMulticastForwarding to 0 effective-
ly disables all multicast forwarding."
DEFVAL { blocked }
::= { qtechOspfIfEntry 18 }
qtechOspfIfDemand OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Demand OSPF procedures (hel-
lo supression to FULL neighbors and setting the
DoNotAge flag on proogated LSAs) should be per-
formed on this interface."
DEFVAL { false }
::= { qtechOspfIfEntry 19 }
qtechOspfIfAuthType OBJECT-TYPE
SYNTAX INTEGER (0..255)
-- none (0),
-- simplePassword (1)
-- md5 (2)
-- default (3)
-- reserved for specification by IANA (> 2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The authentication type specified for an interface. Setting this value to
'default' means using default authentication type referenced to Area Authentication,
this value only for set,not be read. Additional authentication types may
be assigned locally."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { qtechOspfIfEntry 20 }
qtechOspfIfDatabaseFilterAllOut OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Block flooding of OSPF LSA packets to the interface. By
default, OSPF floods new LSAs over all interfaces in the same area,
except the interface on which the LSA arrives."
DEFVAL {disabled}
::= { qtechOspfIfEntry 21 }
qtechOspfIfDesignateRouterId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"DR RouterID of this interface,
when DR does not selected,DR Id is 0.0.0.0"
DEFVAL {'00000000'H}
::= { qtechOspfIfEntry 22 }
qtechOspfIfBackupDesignateRouterId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Backup DR RouterId of this interface ,
when Backup DR does not selected,BDR Id is 0.0.0.0"
DEFVAL {'00000000'H}
::= { qtechOspfIfEntry 23 }
qtechOspfIfWaitInternal OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The wait time of hello generate"
::= { qtechOspfIfEntry 24 }
qtechOspfIfPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object value to 'enabled' ,the interface will
become a passive interface."
DEFVAL { disabled }
::= { qtechOspfIfEntry 25 }
qtechOspfIfCurrentUsedMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"key-id which current used for md5 authentication,this value is
valid from 1 to 255, the value 0 is default value.."
DEFVAL {0}
::= { qtechOspfIfEntry 26 }
-- The Ospf Interface MD5 authentication key configuration table
qtechOspfIfMd5AuthKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration table of the key-id for md5 authentication for OSPF protocol."
::= { qtechOspfMIBObjects 5 }
qtechOspfIfMd5AuthKeyEntry OBJECT-TYPE
SYNTAX QtechOspfIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration entry of the key-id for md5 authentication for OSPF protocol"
INDEX {qtechOspfIfMd5AuthKeyIf, qtechOspfIfMd5AuthKeyId }
::= { qtechOspfIfMd5AuthKeyTable 1 }
QtechOspfIfMd5AuthKeyEntry ::=
SEQUENCE {
qtechOspfIfMd5AuthKeyIf
Unsigned32,
qtechOspfIfMd5AuthKeyId
Unsigned32,
qtechOspfIfMd5AuthKey
OCTET STRING,
qtechOspfIfMd5AuthKeySt
ConfigStatus
}
qtechOspfIfMd5AuthKeyIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Corresponding value of ifIndex for interfaces."
::= { qtechOspfIfMd5AuthKeyEntry 1 }
qtechOspfIfMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the key-id for md5 authentication."
::= { qtechOspfIfMd5AuthKeyEntry 2 }
qtechOspfIfMd5AuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Authentication Key for MD5.
When read, qtechOspfIfMd5AuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
::= { qtechOspfIfMd5AuthKeyEntry 3 }
qtechOspfIfMd5AuthKeySt OBJECT-TYPE
SYNTAX ConfigStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Setting this value to 'invalid' will delete this entry.
Setting this value to 'valid' will have no effect."
::= { qtechOspfIfMd5AuthKeyEntry 4 }
-- The Qtech Ospf Virtual Link Table
qtechOspfVirtTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfVirtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about this router's virtual inter-
faces.Include ospfVirtIfTable in rfc1850"
REFERENCE
"ospfVirtIfTable in rfc1850"
::= { qtechOspfMIBObjects 6 }
qtechOspfVirtEntry OBJECT-TYPE
SYNTAX QtechOspfVirtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Virtual Interface"
INDEX {qtechOspfVirtIfAreaId, qtechOspfVirtIfNeighbor}
::= { qtechOspfVirtTable 1 }
QtechOspfVirtEntry ::=
SEQUENCE {
qtechOspfVirtIfAreaId
AreaID,
qtechOspfVirtIfNeighbor
RouterID,
qtechOspfVirtIfTransitDelay
Unsigned32,
qtechOspfVirtIfRetransInterval
Unsigned32,
qtechOspfVirtIfHelloInterval
HelloRange,
qtechOspfVirtIfRtrDeadInterval
PositiveInteger,
qtechOspfVirtIfState
INTEGER,
qtechOspfVirtIfEvents
Counter32,
qtechOspfVirtIfAuthType
INTEGER,
qtechOspfVirtIfAuthKey
OCTET STRING,
qtechOspfVirtIfStatus
RowStatus,
qtechOspfVirtCost
Unsigned32,
qtechOspfVirtNativeIfIndex
INTEGER,
qtechOspfVirtLinkState
INTEGER,
qtechOspfVirtHelloDueIn
TimeTicks,
qtechOspfVirtCurrentUsedMd5AuthKeyId
Unsigned32
}
qtechOspfVirtIfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0"
::= { qtechOspfVirtEntry 1 }
qtechOspfVirtIfNeighbor OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Virtual Neighbor."
::= { qtechOspfVirtEntry 2 }
qtechOspfVirtIfTransitDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link- state update packet over this
interface."
DEFVAL { 1 }
::= { qtechOspfVirtEntry 3 }
qtechOspfVirtIfRetransInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets. This
value should be well over the expected round-
trip time."
DEFVAL { 5 }
::= { qtechOspfVirtEntry 4 }
qtechOspfVirtIfHelloInterval OBJECT-TYPE
SYNTAX HelloRange
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for the
virtual neighbor."
DEFVAL { 10 }
::= { qtechOspfVirtEntry 5 }
qtechOspfVirtIfRtrDeadInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for the virtual neigh-
bor."
DEFVAL { 40 }
::= { qtechOspfVirtEntry 6 }
qtechOspfVirtIfState OBJECT-TYPE
SYNTAX INTEGER {
down (1), -- these use the same encoding
pointToPoint (4) -- as the ospfIfTable
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"OSPF virtual interface states."
DEFVAL { down }
::= { qtechOspfVirtEntry 7 }
qtechOspfVirtIfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of state changes or error events on
this Virtual Link"
::= { qtechOspfVirtEntry 8 }
qtechOspfVirtIfAuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If Authentication Type is simplePassword, the
device will left adjust and zero fill to 8 oc-
tets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, ospfVifAuthKey always returns a
string of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0
::= { qtechOspfVirtEntry 9 }
qtechOspfVirtIfStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { qtechOspfVirtEntry 10 }
qtechOspfVirtIfAuthType OBJECT-TYPE
SYNTAX INTEGER (0..255)
-- none (0),
-- simplePassword (1),
-- md5 (2),
-- default (3)
-- reserved for specification by IANA (> 2)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication type specified for a virtual interface. Setting this value
'default' means using default authentication type referenced to Area Authentication,
this value only for set,not be read. Additional authentication types
may be assigned locally."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { qtechOspfVirtEntry 11 }
qtechOspfVirtCost OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Explicitly specify the cost of sending a packet on the
interface."
::= { qtechOspfVirtEntry 12 }
qtechOspfVirtNativeIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the Interface's Index that The Virtual Link
via this interface."
::= { qtechOspfVirtEntry 13 }
qtechOspfVirtLinkState OBJECT-TYPE
SYNTAX INTEGER{
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Virtual Link State is up or down."
::= { qtechOspfVirtEntry 14 }
qtechOspfVirtHelloDueIn OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the time when hello due in."
::= { qtechOspfVirtEntry 15 }
qtechOspfVirtCurrentUsedMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"the key-id which current used for md5 authentication,this value is
valid from 1 to 255, the value 0 is default value."
DEFVAL {0}
::= { qtechOspfVirtEntry 16 }
-- The Ospf Virtual Interface MD5 authentication key configuration table
qtechOspfVirtIfMd5AuthKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfVirtIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration table of the key-id for md5 authentication in VirtIf
for OSPF protocol."
::= { qtechOspfMIBObjects 7 }
qtechOspfVirtIfMd5AuthKeyEntry OBJECT-TYPE
SYNTAX QtechOspfVirtIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration entry of the key-id for md5 authentication in VirtIf
for OSPF protocol"
INDEX {qtechOspfVirtIfMd5AuthKeyAreaId, qtechOspfVirtIfMd5AuthKeyNeighbor,
qtechOspfVirtIfMd5AuthKeyId }
::= { qtechOspfVirtIfMd5AuthKeyTable 1 }
QtechOspfVirtIfMd5AuthKeyEntry ::=
SEQUENCE {
qtechOspfVirtIfMd5AuthKeyAreaId
AreaID,
qtechOspfVirtIfMd5AuthKeyNeighbor
RouterID,
qtechOspfVirtIfMd5AuthKeyId
Unsigned32,
qtechOspfVirtIfMd5AuthKey
OCTET STRING,
qtechOspfVirtIfMd5AuthKeySt
ConfigStatus
}
qtechOspfVirtIfMd5AuthKeyAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0"
::= { qtechOspfVirtIfMd5AuthKeyEntry 1 }
qtechOspfVirtIfMd5AuthKeyNeighbor OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Virtual Neighbor."
::= { qtechOspfVirtIfMd5AuthKeyEntry 2 }
qtechOspfVirtIfMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the key-id for md5 authentication."
::= { qtechOspfVirtIfMd5AuthKeyEntry 3 }
qtechOspfVirtIfMd5AuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Authentication Key for MD5.
When read, qtechOspfVirtIfMd5AuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
::= { qtechOspfVirtIfMd5AuthKeyEntry 4 }
qtechOspfVirtIfMd5AuthKeySt OBJECT-TYPE
SYNTAX ConfigStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Setting this value to 'invalid' will delete this entry.
Setting this value to 'valid' will have no effect."
::= { qtechOspfVirtIfMd5AuthKeyEntry 5 }
qtechOspfLsaDetailInfoMibsGroup OBJECT IDENTIFIER ::= { qtechOspfMIBObjects 8 }
-- OSPF Link State Database
-- The Link State Database contains the Link State
-- Advertisements from throughout the areas that the
-- device is attached to.
qtechOspfLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Process's Link State Database."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { qtechOspfLsaDetailInfoMibsGroup 1 }
qtechOspfLsdbEntry OBJECT-TYPE
SYNTAX QtechOspfLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Link State Advertisement."
INDEX { qtechOspfLsdbAreaId, qtechOspfLsdbType,
qtechOspfLsdbLsid, qtechOspfLsdbRouterId }
::= { qtechOspfLsdbTable 1 }
QtechOspfLsdbEntry ::=
SEQUENCE {
qtechOspfLsdbAreaId
AreaID,
qtechOspfLsdbType
INTEGER,
qtechOspfLsdbLsid
IpAddress,
qtechOspfLsdbRouterId
RouterID,
qtechOspfLsdbSequence
Unsigned32,
qtechOspfLsdbAge
Unsigned32,
qtechOspfLsdbChecksum
Unsigned32,
qtechOspfLsdbAdvertisement
OCTET STRING,
qtechOspfLsdbLinkNum --equal LinkCount
Unsigned32,
qtechOspfLsdbPacketLength
Unsigned32,
qtechOspfSummaryLsaNetworkMask
IpAddress,
qtechOspfSummaryLsaTos0Metric
Unsigned32,
qtechOspfNssaLsaDetailMetricType
INTEGER,
qtechOspfNssaLsaDetailForwardAddr
IpAddress,
qtechOspfNssaLsaDetailRouteTag
Unsigned32,
qtechOspfLsdbOption
Unsigned32
}
qtechOspfLsdbAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit identifier of the Area from which
the LSA was received."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { qtechOspfLsdbEntry 1 }
-- External Link State Advertisements are permitted
-- for backward compatibility, but should be displayed in
-- the ospfExtLsdbTable rather than here.
qtechOspfLsdbType OBJECT-TYPE
SYNTAX INTEGER {
routerLink (1),
networkLink (2),
summaryLink (3),
asSummaryLink (4),
asExternalLink (5), -- but see qtechOspfExtLsdbTable
multicastLink (6),
nssaExternalLink (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate advertise-
ment format."
REFERENCE
"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"
::= { qtechOspfLsdbEntry 2 }
qtechOspfLsdbLsid OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.4 Link State ID"
::= { qtechOspfLsdbEntry 3 }
qtechOspfLsdbRouterId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { qtechOspfLsdbEntry 4 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It qtechs with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
qtechOspfLsdbSequence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { qtechOspfLsdbEntry 5 }
qtechOspfLsdbAge OBJECT-TYPE
SYNTAX Unsigned32 -- Should be 0..MaxAge
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state adver-
tisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { qtechOspfLsdbEntry 6 }
qtechOspfLsdbChecksum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { qtechOspfLsdbEntry 7 }
qtechOspfLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { qtechOspfLsdbEntry 8 }
qtechOspfLsdbLinkNum OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the link count of this Router Link Lsa ,
this field is only valid for Router Link Lsa<73><61>type 1 LSA)"
::= { qtechOspfLsdbEntry 9 }
qtechOspfLsdbPacketLength OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the lsa packet length ."
::= { qtechOspfLsdbEntry 10 }
qtechOspfSummaryLsaNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is only useful when ospfLsdbType is type-3 or
type-4 or type-7,it's the Lsa's network mask ."
::= { qtechOspfLsdbEntry 11 }
qtechOspfSummaryLsaTos0Metric OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is only useful when ospfLsdbType is type-3 or
type-4 or type-7,it's the Lsa's tos0 metric ."
::= { qtechOspfLsdbEntry 12 }
qtechOspfNssaLsaDetailMetricType OBJECT-TYPE
SYNTAX INTEGER
{ type1(1),
type2(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" this field is valid when Lsa is a type-7 LSA.
The type of Nssa ernal metric. If bit E is set, the metric
specified is a Type 2 external metric. This means the metric is
considered larger than any link state path. If bit E is zero,
the specified metric is a Type 1 external metric. This means
that it is expressed in the same units as the link state metric
(i.e., the same units as interface cost). "
::= { qtechOspfLsdbEntry 13 }
qtechOspfNssaLsaDetailForwardAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is valid when Lsa is a type-7 LSA.
Data traffic for the advertised destination will be forwarded to
this address. If the Forwarding address is set to 0.0.0.0, data
traffic will be forwarded instead to the LSA's originator (i.e.,
the responsible AS boundary router) ."
::= { qtechOspfLsdbEntry 14 }
qtechOspfNssaLsaDetailRouteTag OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" this field is valid when Lsa is a type-7 LSA.
A 32-bit field attached to each external route. This is not
used by the OSPF protocol itself. It may be used to communicate
information between AS boundary routers; the precise nature of
such information is outside the scope of this specification."
::= { qtechOspfLsdbEntry 15 }
qtechOspfLsdbOption OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the option field indicate which optional capabilities
area associated with the LSA. "
REFERENCE
"OSPF Version 2, Appendix A.2, the Options Field"
::= { qtechOspfLsdbEntry 16 }
-- OSPF Link State Database, External
-- The Link State Database contains the Link State
-- Advertisements from throughout the areas that the
-- device is attached to.
-- This table is identical to the OSPF LSDB Table in
-- format, but contains only External Link State
-- Advertisements. The purpose is to allow external
-- LSAs to be displayed once for the router rather
-- than once in each non-stub area.
qtechOspfExtLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfExtLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Process's Links State Database."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { qtechOspfLsaDetailInfoMibsGroup 2 }
qtechOspfExtLsdbEntry OBJECT-TYPE
SYNTAX QtechOspfExtLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Link State Advertisement."
INDEX { qtechOspfExtLsdbType, qtechOspfExtLsdbLsid, qtechOspfExtLsdbRouterId }
::= { qtechOspfExtLsdbTable 1 }
QtechOspfExtLsdbEntry ::=
SEQUENCE{
qtechOspfExtLsdbType
INTEGER,
qtechOspfExtLsdbLsid
IpAddress,
qtechOspfExtLsdbRouterId
RouterID,
qtechOspfExtLsdbSequence
Unsigned32,
qtechOspfExtLsdbAge
Unsigned32,
qtechOspfExtLsdbChecksum
Unsigned32,
qtechOspfExtLsdbAdvertisement
OCTET STRING,
qtechOspfExtLsdbNetworkMask
IpAddress,
qtechOspfExtLsdbMetricType
INTEGER,
qtechOspfExtLsdbForwardAddr
IpAddress,
qtechOspfExtLsdbRouteTag
Unsigned32,
qtechOspfExtLsdbMetric
INTEGER,
qtechOspfExtLsdbOption
Unsigned32,
qtechOspfExtLsdbPacketLength
Unsigned32
}
qtechOspfExtLsdbType OBJECT-TYPE
SYNTAX INTEGER {
asExternalLink (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate advertise-
ment format."
REFERENCE
"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"
::= { qtechOspfExtLsdbEntry 1 }
qtechOspfExtLsdbLsid OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.4 Link State ID"
::= { qtechOspfExtLsdbEntry 2 }
qtechOspfExtLsdbRouterId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { qtechOspfExtLsdbEntry 3 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It qtechs with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
qtechOspfExtLsdbSequence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { qtechOspfExtLsdbEntry 4 }
qtechOspfExtLsdbAge OBJECT-TYPE
SYNTAX Unsigned32 -- Should be 0..MaxAge
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state adver-
tisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { qtechOspfExtLsdbEntry 5 }
qtechOspfExtLsdbChecksum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { qtechOspfExtLsdbEntry 6 }
qtechOspfExtLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(36))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { qtechOspfExtLsdbEntry 7 }
qtechOspfExtLsdbNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address mask for the advertised destination. For
example, when advertising a class A network the mask 0xff000000
would be used."
::= { qtechOspfExtLsdbEntry 8 }
qtechOspfExtLsdbMetric OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The cost of this route. Interpretation depends on the external
type indication. "
::= { qtechOspfExtLsdbEntry 9 }
qtechOspfExtLsdbMetricType OBJECT-TYPE
SYNTAX INTEGER
{ type1(1),
type2(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The type of external metric. If bit E is set, the metric
specified is a Type 2 external metric. This means the metric is
considered larger than any link state path. If bit E is zero,
the specified metric is a Type 1 external metric. This means
that it is expressed in the same units as the link state metric
(i.e., the same units as interface cost). "
::= { qtechOspfExtLsdbEntry 10 }
qtechOspfExtLsdbForwardAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Data traffic for the advertised destination will be forwarded to
this address. If the Forwarding address is set to 0.0.0.0, data
traffic will be forwarded instead to the LSA's originator (i.e.,
the responsible AS boundary router) ."
::= { qtechOspfExtLsdbEntry 11 }
qtechOspfExtLsdbRouteTag OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit field attached to each external route. This is not
used by the OSPF protocol itself. It may be used to communicate
information between AS boundary routers; the precise nature of
such information is outside the scope of this specification."
::= { qtechOspfExtLsdbEntry 12 }
qtechOspfExtLsdbOption OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the option field indicate which optional capabilities
area associated with the LSA. "
REFERENCE
"OSPF Version 2, Appendix A.2, the Options Field"
::= { qtechOspfExtLsdbEntry 13 }
qtechOspfExtLsdbPacketLength OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the lsa packet length ."
::= { qtechOspfExtLsdbEntry 14 }
--Router Lsa's detail information table
qtechOspfRouterLsaDetailTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfRouterLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the router Lsa's detail Infromtion."
::= { qtechOspfLsaDetailInfoMibsGroup 3 }
qtechOspfRouterLsaDetailEntry OBJECT-TYPE
SYNTAX QtechOspfRouterLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {qtechOspfLsdbAreaId, qtechOspfLsdbType,
qtechOspfLsdbLsid, qtechOspfLsdbRouterId,
qtechOspfRouterLsaDetailLinkID
}
::= { qtechOspfRouterLsaDetailTable 1 }
QtechOspfRouterLsaDetailEntry ::=
SEQUENCE{
qtechOspfRouterLsaDetailLinkID
IpAddress,
qtechOspfRouterLsaDetailLinkType
INTEGER,
qtechOspfRouterLsaDetailLinkData
IpAddress,
qtechOspfRouterLsaDetailTos0Metric
Unsigned32
}
qtechOspfRouterLsaDetailLinkID OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"router lsa's link ID Identifies the object that this router
link connects to. Value depends on the link's Type.
When connecting to an object that also originates an
LSA (i.e., another router or a transit network) the
Link ID is equal to the neighboring LSA's Link
State ID. This provides the key for looking up the neighboring
LSA in the link state database during the routing table
calculation. See Section 12.2 for more details.
Type Link ID
________________________________________
1 Neighboring router's Router ID
2 IP address of Designated Router
3 IP network/subnet number
4 Neighboring router's Router ID
"
::= { qtechOspfRouterLsaDetailEntry 1 }
qtechOspfRouterLsaDetailLinkType OBJECT-TYPE
SYNTAX INTEGER{
pointtopointConnectionToAnotherRouter(1),
connectionToaTransitNetwork(2),
connectionToaStubNetwork(3),
virtualLink(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"router lsa's link type
A quick description of the router link. One of the following.
Note that host routes are classified as links to stub networks
with network mask of 0xffffffff."
::= { qtechOspfRouterLsaDetailEntry 2 }
qtechOspfRouterLsaDetailLinkData OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Value again depends on the link's Type field. For connections to
stub networks, Link Data specifies the network's IP address
mask. For unnumbered point-to-point connections, it specifies
the interface's MIB-II ifIndex value. For the other link
types it specifies the router interface's IP address. This
latter piece of information is needed during the routing table
build process, when calculating the IP address of the next hop. "
::= { qtechOspfRouterLsaDetailEntry 3 }
qtechOspfRouterLsaDetailTos0Metric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"TOS0-specific metric information."
::= { qtechOspfRouterLsaDetailEntry 4 }
--NetWork Lsa's detail information table
qtechOspfNetWorkLsaDetailTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfNetWorkLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the NetWork Lsa's detail Infromtion."
::= { qtechOspfLsaDetailInfoMibsGroup 4 }
qtechOspfNetWorkLsaDetailEntry OBJECT-TYPE
SYNTAX QtechOspfNetWorkLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {qtechOspfLsdbAreaId, qtechOspfLsdbType,
qtechOspfLsdbLsid, qtechOspfLsdbRouterId,
qtechOspfNetWorkLsaDetailAttachedRouter
}
::= { qtechOspfNetWorkLsaDetailTable 1 }
QtechOspfNetWorkLsaDetailEntry ::=
SEQUENCE{
qtechOspfNetWorkLsaDetailAttachedRouter
IpAddress,
qtechOspfNetWorkLsaDetailNetworkMask
IpAddress
}
qtechOspfNetWorkLsaDetailAttachedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The Router IDs of each of the routers attached to the network.
Actually, only those routers that are fully adjacent to the
Designated Router are listed. The Designated Router includes
itself in this list. The number of routers included can be
deduced from the LSA header's length field. "
::= { qtechOspfNetWorkLsaDetailEntry 1 }
qtechOspfNetWorkLsaDetailNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address mask for the network. For example, a class A
network would have the mask 0xff000000."
::= { qtechOspfNetWorkLsaDetailEntry 2 }
--qtech Ospf Area Lsa Database Summary Table
qtechOspfAreaLsaDBSumTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfAreaLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Area LSA database summary Infromtion."
::= { qtechOspfLsaDetailInfoMibsGroup 5 }
qtechOspfAreaLsaDBSumEntry OBJECT-TYPE
SYNTAX QtechOspfAreaLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {qtechOspfAreaLsaDBSumAreaId,
qtechOspfAreaLsaDBSumLsaType
}
::= { qtechOspfAreaLsaDBSumTable 1 }
QtechOspfAreaLsaDBSumEntry ::=
SEQUENCE{
qtechOspfAreaLsaDBSumAreaId
IpAddress,
qtechOspfAreaLsaDBSumLsaType
INTEGER,
qtechOspfAreaLsaDBSumCounts
Counter32,
qtechOspfAreaLsaDBSumDeletes
Counter32,
qtechOspfAreaLsaDBSumMaxage
Counter32
}
qtechOspfAreaLsaDBSumAreaId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The area Id."
::= { qtechOspfAreaLsaDBSumEntry 1 }
qtechOspfAreaLsaDBSumLsaType OBJECT-TYPE
SYNTAX INTEGER
{ routerLink (1),
networkLink (2),
summaryLink (3),
asSummaryLink (4),
--asExternalLink (5), because in each area,type 5 lsa is no meaning
--it's only meaning in one router
-- multicastLink (6), not implement
nssaExternalLink (7),
subtotal(8)
--subtotal is use for total counter for all type LSA in this area.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the entry's entry type."
::= { qtechOspfAreaLsaDBSumEntry 2 }
qtechOspfAreaLsaDBSumCounts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number os this type Lsa in this area ,
if this type Lsa does not exist,this field is 0."
::= { qtechOspfAreaLsaDBSumEntry 3 }
qtechOspfAreaLsaDBSumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number os this type Lsa which has been delete in this area ,
if this type Lsa is not been deleted,this field is 0"
::= { qtechOspfAreaLsaDBSumEntry 4 }
qtechOspfAreaLsaDBSumMaxage OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number of this type Lsa which has up to Maxage,
if this type Lsa which has up to Maxage does not exist,
this field is 0"
::= { qtechOspfAreaLsaDBSumEntry 5 }
--qtech Ospf Lsa Database total summary table
qtechOspfLsaDBSumTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"LSA database total summary infromtion in the all areas ."
::= { qtechOspfLsaDetailInfoMibsGroup 6 }
qtechOspfLsaDBSumEntry OBJECT-TYPE
SYNTAX QtechOspfLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {
qtechOspfLsaDBSumLsaType
}
::= { qtechOspfLsaDBSumTable 1 }
QtechOspfLsaDBSumEntry ::=
SEQUENCE{
qtechOspfLsaDBSumLsaType
INTEGER,
qtechOspfLsaDBSumCounts
Counter32,
qtechOspfLsaDBSumDeletes
Counter32,
qtechOspfLsaDBSumMaxage
Counter32
}
qtechOspfLsaDBSumLsaType OBJECT-TYPE
SYNTAX INTEGER
{ routerLink (1),
networkLink (2),
summaryTotalLink (3),
asSummaryTotalLink (4),
asExternalLink (5),
-- multicastLink (6), not implement
nssaExternalLink (7),
total(8)
--subtotal is use for total counter for all type LSA in this router.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the table's entry type."
::= { qtechOspfLsaDBSumEntry 1 }
qtechOspfLsaDBSumCounts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"total number of this type Lsa in all area ."
::= { qtechOspfLsaDBSumEntry 2 }
qtechOspfLsaDBSumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" total number of this type Lsa deleted in all area ."
::= { qtechOspfLsaDBSumEntry 3 }
qtechOspfLsaDBSumMaxage OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"total number of this type Lsa which has been up to max age in all area "
::= { qtechOspfLsaDBSumEntry 4 }
-- The OSPF Neighbor Table describes all neighbors in
-- the locality of the subject router.
qtechOspfNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the neighbor detail infomation ."
REFERENCE
"ospfNbrTable in rfc1850"
::= { qtechOspfMIBObjects 9 }
qtechOspfNeighborEntry OBJECT-TYPE
SYNTAX QtechOspfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX { qtechOspfNbrIpAddr,
qtechOspfNbrAddressLessIndex
}
::= { qtechOspfNeighborTable 1 }
QtechOspfNeighborEntry ::=
SEQUENCE{
qtechOspfNbrIpAddr
IpAddress,
qtechOspfNbrAddressLessIndex
Unsigned32,
qtechOspfNbrRtrId
RouterID,
qtechOspfNbrOptions
Unsigned32,
qtechOspfNbrPriority
DesignatedRouterPriority,
qtechOspfNbrState
INTEGER,
qtechOspfNbrEvents
Counter32,
qtechOspfNbrLsRetransQLen
Gauge32,
qtechOspfNbmaNbrStatus
RowStatus,
qtechOspfNbmaNbrPermanence
INTEGER,
qtechOspfNbrHelloSuppressed
TruthValue,
qtechOspfNbrDeadTimeDueIn
TimeTicks,
qtechOspfNbrNeighborUpTime
TimeTicks,
qtechOspfNbrDR
IpAddress,
qtechOspfNbrBDR
IpAddress,
qtechOspfNbrArea
IpAddress,
qtechOspfNbrRetransmissionNum
Counter32,
qtechOspfNbrIfState
INTEGER
}
qtechOspfNbrIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address this neighbor(neighbor's interface IP address)
is using in its IP Source Address. Note that, on addressless
links, this will not be 0.0.0.0, but the ad-
dress of another of the neighbor's interfaces."
::= { qtechOspfNeighborEntry 1 }
qtechOspfNbrAddressLessIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"On an interface having an IP Address, zero.
On addressless interfaces, the corresponding
value of ifIndex in the Internet Standard MIB.
On row creation, this can be derived from the
instance."
::= { qtechOspfNeighborEntry 2 }
qtechOspfNbrRtrId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer (represented as a type IpAd-
dress) uniquely identifying the neighboring
router in the Autonomous System."
::= { qtechOspfNeighborEntry 3 }
qtechOspfNbrOptions OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A Bit Mask corresponding to the neighbor's op-
tions field.
Bit 0, if set, indicates that the system will
operate on Type of Service metrics other than
TOS 0. If zero, the neighbor will ignore all
metrics except the TOS 0 metric.
Bit 1, if set, indicates that the associated
area accepts and operates on external informa-
tion; if zero, it is a stub area.
Bit 2, if set, indicates that the system is ca-
pable of routing IP Multicast datagrams; i.e.,
that it implements the Multicast Extensions to
OSPF.
Bit 3, if set, indicates that the associated
area is an NSSA. These areas are capable of
carrying type 7 external advertisements, which
are translated into type 5 external advertise-
ments at NSSA borders."
REFERENCE
"OSPF Version 2, Section 12.1.2 Options"
::= { qtechOspfNeighborEntry 4 }
qtechOspfNbrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The priority of this neighbor in the designat-
ed router election algorithm. The value 0 sig-
nifies that the neighbor is not eligible to be-
come the designated router on this particular
network."
::= { qtechOspfNeighborEntry 5 }
qtechOspfNbrState OBJECT-TYPE
SYNTAX INTEGER {
down (1),
attempt (2),
init (3),
twoWay (4),
exchangeQtech (5),
exchange (6),
loading (7),
full (8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The State of the relationship with this Neigh-
bor."
REFERENCE
"OSPF Version 2, Section 10.1 Neighbor States"
::= { qtechOspfNeighborEntry 6 }
qtechOspfNbrEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this neighbor relationship
has changed state, or an error has occurred."
::= { qtechOspfNeighborEntry 7 }
qtechOspfNbrLsRetransQLen OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current length of the retransmission
queue."
::= { qtechOspfNeighborEntry 8 }
qtechOspfNbmaNbrStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { qtechOspfNeighborEntry 9 }
qtechOspfNbmaNbrPermanence OBJECT-TYPE
SYNTAX INTEGER {
dynamic (1), -- learned through protocol
permanent (2) -- configured address
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. 'dynamic' and 'permanent' refer to how
the neighbor became known."
::= { qtechOspfNeighborEntry 10 }
qtechOspfNbrHelloSuppressed OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Hellos are being suppressed
to the neighbor"
::= { qtechOspfNeighborEntry 11 }
qtechOspfNbrDeadTimeDueIn OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"if in this interval ,hello packet is not been received ,
the neighbor is recognized dead.if received,it
will recovery the dead time which has been setted."
::= { qtechOspfNeighborEntry 12 }
qtechOspfNbrNeighborUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the time that the neighbor has been up."
::= { qtechOspfNeighborEntry 13 }
qtechOspfNbrDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Designated Router of this neighbor."
::= { qtechOspfNeighborEntry 14 }
qtechOspfNbrBDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Backup Designated Router of this neighbor."
::= { qtechOspfNeighborEntry 15 }
qtechOspfNbrArea OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the area where the neighbor is in."
::= { qtechOspfNeighborEntry 16 }
qtechOspfNbrRetransmissionNum OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Retransmission times."
::= { qtechOspfNeighborEntry 17 }
qtechOspfNbrIfState OBJECT-TYPE
SYNTAX INTEGER {
other(0),
designatedRouter (1),
backupDesignatedRouter (2),
otherDesignatedRouter (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The neighbor's interface State which connected to local router."
::= { qtechOspfNeighborEntry 18 }
--OSPF border routing information
qtechOspfRouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF QtechOspfRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entity's OSPF border routing table."
::= { qtechOspfMIBObjects 10 }
qtechOspfRouteEntry OBJECT-TYPE
SYNTAX QtechOspfRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A route to a destination."
INDEX {
qtechOspfRouteDest,
qtechOspfRouteArea,
qtechOspfRouteNextHop
}
::= { qtechOspfRouteTable 1 }
QtechOspfRouteEntry ::=
SEQUENCE {
qtechOspfRouteDest
IpAddress,
qtechOspfRouteArea
IpAddress,
qtechOspfRouteNextHop
IpAddress,
qtechOspfRouteCost
Unsigned32,
qtechOspfRouteType
INTEGER,
qtechOspfRouteDRType
INTEGER,
qtechOspfRouteSpfNo
Counter32
}
qtechOspfRouteDest OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Router ID of the destination."
::= { qtechOspfRouteEntry 1 }
qtechOspfRouteArea OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The area ID of the area from which this route is learned."
::= { qtechOspfRouteEntry 2 }
qtechOspfRouteNextHop OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Next hop toward the destination."
::= { qtechOspfRouteEntry 3 }
qtechOspfRouteCost OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Cost of using this route."
::= { qtechOspfRouteEntry 4 }
qtechOspfRouteDRType OBJECT-TYPE
SYNTAX INTEGER {
abr(1),
asbr(2),
both(3) --abr and asbr
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The router type of the destination;
it is either an ABR or ASBR or both."
::= { qtechOspfRouteEntry 5 }
qtechOspfRouteType OBJECT-TYPE
SYNTAX INTEGER {
intral-area-route(1),
inter-area-route(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field indicate this route is an intral area route
or inter area route."
::= { qtechOspfRouteEntry 6 }
qtechOspfRouteSpfNo OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The internal number of the shortest path first (SPF) calculation that
installs this route."
::= { qtechOspfRouteEntry 7 }
-- conformance information
qtechOspfMIBConformance OBJECT IDENTIFIER ::= { qtechOspfMIB 2 }
qtechOspfMIBCompliances OBJECT IDENTIFIER ::= { qtechOspfMIBConformance 1 }
qtechOspfMIBGroups OBJECT IDENTIFIER ::= { qtechOspfMIBConformance 2 }
-- compliance statements
qtechOspfMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which implement
the Qtech OSPF MIB"
MODULE -- this module
MANDATORY-GROUPS {
qtechOspfBaseMIBGroup,
qtechOspfAreaMIBGroup,
qtechOspfLsaMIBGroup,
qtechOspfIfMIBGroup,
qtechOspfVirtMIBGroup,
qtechOspfNeighborMIBGroup,
qtechOspfRouteInfoMIBGroup
}
::= { qtechOspfMIBCompliances 1 }
-- units of conformance
qtechOspfBaseMIBGroup OBJECT-GROUP
OBJECTS {
qtechOspfMiniLsaInterval ,
qtechOspfMiniLsaArrival ,
qtechOspfAreasNum ,
qtechOspfNormalAreasNum ,
qtechOspfStubAreasNum ,
qtechOspfNssaAreasNum ,
qtechOspfSpfDelay ,
qtechOspfSpfHoldTime ,
qtechOspfAutoCostRefBandWidthRef ,
qtechOspfLsaGroupPacing ,
qtechOspfInterDistance ,
qtechOspfIntraDistance ,
qtechOspfExternDistance ,
qtechOspfLogAdjChangeNotify ,
qtechOspfPassiveStatus ,
qtechOspfRFC1583Compatibility ,
qtechOspfRouteRedisDefMetricVal
}
STATUS current
DESCRIPTION
"A collection of general objects providing OSPF managment."
::= { qtechOspfMIBGroups 1 }
qtechOspfAreaMIBGroup OBJECT-GROUP
OBJECTS {
qtechOspfAreaId,
qtechOspfAuthType,
qtechOspfImportAsExtern,
qtechOspfSpfRuns,
qtechOspfAreaBdrRtrCount,
qtechOspfAsBdrRtrCount,
qtechOspfAreaLsaCount,
qtechOspfAreaLsaCksumSum,
qtechOspfAreaSummary,
qtechOspfAreaStatus,
qtechOspfAreaInterfaceNum,
qtechOspfAreaNssaIsRedistribution,
qtechOspfAreaNssaIsDefInfoOriginate,
qtechOspfNetWorkAreaID,
qtechOspfNetWorkAddress,
qtechOspfNetWorkMask,
qtechOspfNetWorkStatus
}
STATUS current
DESCRIPTION
"A collection of area objects providing OSPF managment."
::= { qtechOspfMIBGroups 2 }
qtechOspfLsaMIBGroup OBJECT-GROUP
OBJECTS {
qtechOspfLsdbAreaId,
qtechOspfLsdbType,
qtechOspfLsdbLsid,
qtechOspfLsdbRouterId,
qtechOspfLsdbSequence,
qtechOspfLsdbAge,
qtechOspfLsdbChecksum,
qtechOspfLsdbAdvertisement,
qtechOspfLsdbLinkNum,
qtechOspfLsdbPacketLength,
qtechOspfSummaryLsaNetworkMask,
qtechOspfSummaryLsaTos0Metric,
qtechOspfNssaLsaDetailMetricType,
qtechOspfNssaLsaDetailForwardAddr ,
qtechOspfNssaLsaDetailRouteTag ,
qtechOspfLsdbOption,
qtechOspfExtLsdbType,
qtechOspfExtLsdbLsid,
qtechOspfExtLsdbRouterId,
qtechOspfExtLsdbSequence,
qtechOspfExtLsdbAge,
qtechOspfExtLsdbChecksum,
qtechOspfExtLsdbAdvertisement,
qtechOspfExtLsdbNetworkMask,
qtechOspfExtLsdbMetricType,
qtechOspfExtLsdbForwardAddr,
qtechOspfExtLsdbRouteTag,
qtechOspfExtLsdbMetric,
qtechOspfExtLsdbOption,
qtechOspfExtLsdbPacketLength,
qtechOspfRouterLsaDetailLinkID,
qtechOspfRouterLsaDetailLinkType,
qtechOspfRouterLsaDetailLinkData,
qtechOspfRouterLsaDetailTos0Metric,
qtechOspfNetWorkLsaDetailAttachedRouter,
qtechOspfNetWorkLsaDetailNetworkMask,
qtechOspfAreaLsaDBSumAreaId,
qtechOspfAreaLsaDBSumLsaType,
qtechOspfAreaLsaDBSumCounts ,
qtechOspfAreaLsaDBSumDeletes,
qtechOspfAreaLsaDBSumMaxage,
qtechOspfLsaDBSumLsaType,
qtechOspfLsaDBSumCounts,
qtechOspfLsaDBSumDeletes,
qtechOspfLsaDBSumMaxage
}
STATUS current
DESCRIPTION
"A collection of OSPF Link State Database objects providing OSPF managment."
::= { qtechOspfMIBGroups 3 }
qtechOspfIfMIBGroup OBJECT-GROUP
OBJECTS {
qtechOspfIfIpAddress,
qtechOspfAddressLessIf,
qtechOspfIfAreaId,
qtechOspfIfType,
qtechOspfIfAdminStat,
qtechOspfIfRtrPriority,
qtechOspfIfTransitDelay,
qtechOspfIfRetransInterval,
qtechOspfIfHelloInterval,
qtechOspfIfRtrDeadInterval,
qtechOspfIfPollInterval,
qtechOspfIfState,
qtechOspfIfDesignatedRouter,
qtechOspfIfBackupDesignatedRouter,
qtechOspfIfEvents,
qtechOspfIfAuthType,
qtechOspfIfAuthKey,
qtechOspfIfStatus,
qtechOspfIfMulticastForwarding,
qtechOspfIfDemand,
qtechOspfIfDatabaseFilterAllOut,
qtechOspfIfDesignateRouterId ,
qtechOspfIfBackupDesignateRouterId ,
-- qtechOspfIfMd5AuthKeyId,
qtechOspfIfWaitInternal,
qtechOspfIfPassiveStatus,
qtechOspfIfCurrentUsedMd5AuthKeyId,
qtechOspfIfMd5AuthKeyIf,
qtechOspfIfMd5AuthKeyId,
qtechOspfIfMd5AuthKey,
qtechOspfIfMd5AuthKeySt
}
STATUS current
DESCRIPTION
"A collection of OSPF interface managment."
::= { qtechOspfMIBGroups 4 }
qtechOspfVirtMIBGroup OBJECT-GROUP
OBJECTS {
qtechOspfVirtIfAreaId,
qtechOspfVirtIfNeighbor,
qtechOspfVirtIfTransitDelay,
qtechOspfVirtIfRetransInterval,
qtechOspfVirtIfHelloInterval,
qtechOspfVirtIfRtrDeadInterval,
qtechOspfVirtIfState,
qtechOspfVirtIfEvents,
qtechOspfVirtIfAuthType,
qtechOspfVirtIfAuthKey,
qtechOspfVirtIfStatus,
qtechOspfVirtCost,
qtechOspfVirtNativeIfIndex,
qtechOspfVirtLinkState,
qtechOspfVirtHelloDueIn,
qtechOspfVirtIfMd5AuthKeyAreaId,
qtechOspfVirtIfMd5AuthKeyNeighbor,
qtechOspfVirtIfMd5AuthKeyId,
qtechOspfVirtIfMd5AuthKey,
qtechOspfVirtIfMd5AuthKeySt,
qtechOspfVirtCurrentUsedMd5AuthKeyId
}
STATUS current
DESCRIPTION
"A collection of OSPF Virtual Link managment."
::= { qtechOspfMIBGroups 5 }
qtechOspfNeighborMIBGroup OBJECT-GROUP
OBJECTS {
qtechOspfNbrIpAddr,
qtechOspfNbrAddressLessIndex,
qtechOspfNbrRtrId,
qtechOspfNbrOptions,
qtechOspfNbrPriority,
qtechOspfNbrState,
qtechOspfNbrEvents,
qtechOspfNbrLsRetransQLen,
qtechOspfNbmaNbrStatus,
qtechOspfNbmaNbrPermanence,
qtechOspfNbrHelloSuppressed,
qtechOspfNbrDeadTimeDueIn,
qtechOspfNbrNeighborUpTime,
qtechOspfNbrDR,
qtechOspfNbrBDR,
qtechOspfNbrArea,
qtechOspfNbrRetransmissionNum
}
STATUS current
DESCRIPTION
"A collection of OSPF Neighbor information."
::= { qtechOspfMIBGroups 6 }
qtechOspfRouteInfoMIBGroup OBJECT-GROUP
OBJECTS {
qtechOspfRouteType,
qtechOspfRouteDest,
qtechOspfRouteNextHop,
qtechOspfRouteCost,
qtechOspfRouteDRType,
qtechOspfRouteArea,
qtechOspfRouteSpfNo
}
STATUS current
DESCRIPTION
"A collection of OSPF route information."
::= { qtechOspfMIBGroups 7 }
-- -------------------------------------------------------------
-- Compliance statements
-- -------------------------------------------------------------
ospfMIBConformance OBJECT IDENTIFIER ::= { qtechOspfMIB 3 }
ospfMIBCompliances OBJECT IDENTIFIER ::= { ospfMIBConformance 1 }
ospfExternCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for device support of OSPF
services."
MODULE
-- OBJECT ospfASBdrRtrStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfTOSSupport
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfExtLsdbLimit
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfMulticastExtensions
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfExitOverflowInterval
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfDemandExtensions
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfIfAreaId
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfIfStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Create access is not required."
--
--
-- OBJECT ospfStubMetric
-- MIN-ACCESS read-write
-- DESCRIPTION "Create access is not required."
--
-- OBJECT ospfStubStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfStubMetricType
-- MIN-ACCESS read-write
-- DESCRIPTION "Create access is not required."
--
-- OBJECT ospfIfAdminStat
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfNbmaNbrStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfNbrPriority
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfIfPollInterval
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfIfTransitDelay
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfIfRetransInterval
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfVirtIfTransitDelay
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfIfType
-- SYNTAX INTEGER {
-- broadcast (1),
-- nbma (2),
-- pointToPoint (3),
-- pointToMultipoint (5),
-- loopback(6)
-- }
-- DESCRIPTION "add type 'loopback'."
--
-- OBJECT ospfVirtIfRetransInterval
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
OBJECT qtechOspfVirtIfRtrDeadInterval
SYNTAX PositiveInteger
DESCRIPTION "default value change from 60 to 40."
::= { ospfMIBCompliances 1 }
END
View Git Blame Copy Permalink