WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/fscom/FS-OSPF-MIB

2957 lines
98 KiB
Plaintext
Raw Blame History

-- *****************************************************************
-- FS-OSPF-MIB.mib: FS Ospf MIB file
--
-- November 2002, ChenXingBin
--
-- Copyright (c) 2002 by FS.COM Inc..
-- All rights reserved.
--
-- *****************************************************************
--
FS-OSPF-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
TimeTicks,
IpAddress,
Unsigned32,
Gauge32,
Counter32
FROM SNMPv2-SMI
TruthValue,
RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF
ConfigStatus
FROM FS-TC
EnabledStatus
FROM P-BRIDGE-MIB
AreaID,
Status,
PositiveInteger,
DesignatedRouterPriority,
RouterID,
HelloRange
FROM OSPF-MIB
fsMgmt
FROM FS-SMI;
fsOspfMIB MODULE-IDENTITY
LAST-UPDATED "200211200000Z"
ORGANIZATION "FS.COM Inc.."
CONTACT-INFO
"
Tel: 400-865-2852
E-mail: https://www.fs.com/live_chat_service_mail.html"
DESCRIPTION
"This module defines fs Ospf mibs."
REVISION "200211200000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { fsMgmt 30}
fsOspfMIBObjects OBJECT IDENTIFIER ::= { fsOspfMIB 1 }
-- general mib
fsOspfGeneralMibsGroup OBJECT IDENTIFIER ::= { fsOspfMIBObjects 1 }
--Minimum LSA interval
fsOspfMiniLsaInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum LSA interval that the two LSA generate."
::={ fsOspfGeneralMibsGroup 1 }
--Minimum LSA arrival
fsOspfMiniLsaArrival OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum LSA Interval of the two LSA arrival."
::={ fsOspfGeneralMibsGroup 2 }
--Number of areas in this router
fsOspfAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of areas in this router"
::={ fsOspfGeneralMibsGroup 3 }
fsOspfNormalAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of normal areas in this router"
::={ fsOspfGeneralMibsGroup 4}
fsOspfStubAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of stub areas in this router"
::={ fsOspfGeneralMibsGroup 5 }
fsOspfNssaAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of nssa areas in this router"
::={ fsOspfGeneralMibsGroup 6 }
fsOspfSpfDelay OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Ospf Spf shedule time, an integer from 0 to 65535. The default is 5
seconds,0 means no delay."
DEFVAL {5}
::={ fsOspfGeneralMibsGroup 7 }
fsOspfSpfHoldTime OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"hold time between two Spfs.an integer from 0 to 65535. The default is
10 seconds; 0 means no delay."
DEFVAL {10}
::={ fsOspfGeneralMibsGroup 8 }
fsOspfAutoCostRefBandWidthRef OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set AutoCost bandwidth referenc value in unit of Mbits.
Setting this value to 0 indicate that disable the feature of
autocost bandwidth referenc."
DEFVAL {100}
::={ fsOspfGeneralMibsGroup 9 }
fsOspfLsaGroupPacing OBJECT-TYPE
SYNTAX Unsigned32(10..1800)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"set the group pacing of LSAs."
DEFVAL {240}
::={ fsOspfGeneralMibsGroup 10}
fsOspfInterDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set inter-area distance."
DEFVAL {110}
::= { fsOspfGeneralMibsGroup 11 }
fsOspfIntraDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set intra-area distance."
DEFVAL {110}
::= { fsOspfGeneralMibsGroup 12 }
fsOspfExternDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set extern distance."
DEFVAL {110}
::= { fsOspfGeneralMibsGroup 13 }
--LogAdjChangeNotify
fsOspfLogAdjChangeNotify OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"if enabled status is setted,
Send syslog message when a neighbor state changes."
DEFVAL {enabled}
::= { fsOspfGeneralMibsGroup 14 }
fsOspfPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The fsOspfIfPassiveStatus of a interface equal to this object value
when this interface is created. If you change this object value to 'enabled'
or 'disabled'all interfaces which have exist will also change their
fsOspfIfPassiveStatus to 'enabled' or 'disabled'."
DEFVAL { disabled }
::={ fsOspfGeneralMibsGroup 15 }
fsOspfRFC1583Compatibility OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the preference rules used in calculating AS external routes
(RFC2328 Section 16.4) when choosing among multiple AS-external-LSAs
advertising the same destination. When set to 'enabled', the preference
rules remain those specified by RFC 1583 ([Ref9]). When set
to 'disabled', the preference rules are those stated in
'RFC2328 Section 16.4.1' which prevent routing loops when AS-
external-LSAs for the same destination have been originated
from different areas. Set to 'enabled' by default."
REFERENCE
"OSPF Version 2(RFC2328), C.1 Global parameters"
DEFVAL { enabled }
::={ fsOspfGeneralMibsGroup 16 }
fsOspfRouteRedisDefMetricVal OBJECT-TYPE
SYNTAX Unsigned32(1..16777214)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this value is setted,Cause the current routing protocol(ospf)
to use the same metricvalue for all redistributed routes (BGP, RIP, and OSPF)."
DEFVAL {20}
::= { fsOspfGeneralMibsGroup 17}
fsOspfAdminiDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"ospf Administrative distance."
DEFVAL {110}
::= { fsOspfGeneralMibsGroup 18}
--table mib
--fsOspfAreaTable
fsOspfAreaTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfAreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the configured parame-
ters and cumulative statistics of the router's
attached areas.This table is superset of ospfAreaTable"
::= { fsOspfMIBObjects 2}
fsOspfAreaEntry OBJECT-TYPE
SYNTAX FSOspfAreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The entry of fsOspfAreaTable."
INDEX { fsOspfAreaId}
::= { fsOspfAreaTable 1 }
FSOspfAreaEntry ::=
SEQUENCE {
fsOspfAreaId
AreaID,
fsOspfAuthType
INTEGER,
fsOspfImportAsExtern
INTEGER,
fsOspfSpfRuns
Counter32,
fsOspfAreaBdrRtrCount
Gauge32,
fsOspfAsBdrRtrCount
Gauge32,
fsOspfAreaLsaCount
Gauge32,
fsOspfAreaLsaCksumSum
Unsigned32,
fsOspfAreaSummary
INTEGER,
fsOspfAreaStatus
RowStatus,
-- extend parts
fsOspfAreaInterfaceNum
Unsigned32,
fsOspfAreaNssaIsRedistribution
TruthValue,
fsOspfAreaNssaIsDefInfoOriginate
TruthValue
}
fsOspfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying an area.
Area ID 0.0.0.0 is used for the OSPF backbone."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { fsOspfAreaEntry 1 }
fsOspfAuthType OBJECT-TYPE
SYNTAX INTEGER{
none(0),
simplePassword(1),
md5 (2)
-- reserved for specification by IANA (> 2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication type specified for an area.
Additional authentication types may be assigned
locally on a per Area basis."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { fsOspfAreaEntry 2 }
fsOspfImportAsExtern OBJECT-TYPE
SYNTAX INTEGER {
importExternal (1), --normal area
importNoExternal (2), -- stub area
importNssa (3) -- NSSA area
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The area's support for importing AS external
link- state advertisements."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
DEFVAL { importExternal }
::= { fsOspfAreaEntry 3 }
fsOspfSpfRuns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that the intra-area route
table has been calculated using this area's
link-state database. This is typically done
using Dijkstra's algorithm."
::= { fsOspfAreaEntry 4 }
fsOspfAreaBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of area border routers reach-
able within this area. This is initially zero,
and is calculated in each SPF Pass."
::= { fsOspfAreaEntry 5 }
fsOspfAsBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Autonomous System border
routers reachable within this area. This is
initially zero, and is calculated in each SPF
Pass."
::= { fsOspfAreaEntry 6 }
fsOspfAreaLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of link-state advertisements
in this area's link-state database, excluding
AS External LSA's."
::= { fsOspfAreaEntry 7 }
fsOspfAreaLsaCksumSum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32-bit unsigned sum of the link-state ad-
vertisements' LS checksums contained in this
area's link-state database. This sum excludes
external (LS type 5) link-state advertisements.
The sum can be used to determine if there has
been a change in a router's link state data-
base, and to compare the link-state database of
two routers."
DEFVAL { 0 }
::= { fsOspfAreaEntry 8 }
fsOspfAreaSummary OBJECT-TYPE
SYNTAX INTEGER {
noAreaSummary (1),
sendAreaSummary (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable ospfAreaSummary controls the im-
port of summary LSAs into stub areas. It has
no effect on other areas.
If it is noAreaSummary, the router will neither
originate nor propagate summary LSAs into the
stub area. It will rely entirely on its de-
fault route.
If it is sendAreaSummary, the router will both
summarize and propagate summary LSAs."
DEFVAL { sendAreaSummary }
::= { fsOspfAreaEntry 9 }
fsOspfAreaStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { fsOspfAreaEntry 10 }
fsOspfAreaInterfaceNum OBJECT-TYPE --for command "show
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the interface number of this area"
::= { fsOspfAreaEntry 11 }
fsOspfAreaNssaIsRedistribution OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" if it's disabled , when the router is an NSSA ABR and
you want the redistribute command to import routes into normal
areas, but not into the NSSA,
this field is vaild for nssa area"
DEFVAL {true}
::= { fsOspfAreaEntry 12}
fsOspfAreaNssaIsDefInfoOriginate OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"if it's enabled it meaning that on an ABR to allow
importing type 7 LSAs into the NSSA,
this field is valid for nssa area"
DEFVAL {false}
::= { fsOspfAreaEntry 13}
--network address scope table
fsOspfAddressScopeTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfAddressScopeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Define an interface on which OSPF runs and the area ID for that
interface. You can use the wildcard-mask to use a single
command to define one or more multiple interfaces to be
associated with a specific OSPF area. "
::= { fsOspfMIBObjects 3 }
fsOspfAddressScopeEntry OBJECT-TYPE
SYNTAX FSOspfAddressScopeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry define an scope of address for ospf routing."
INDEX { fsOspfNetWorkAreaID,fsOspfNetWorkAddress, fsOspfNetWorkMask}
::= { fsOspfAddressScopeTable 1 }
FSOspfAddressScopeEntry ::=
SEQUENCE {
fsOspfNetWorkAreaID
IpAddress,
fsOspfNetWorkAddress
IpAddress,
fsOspfNetWorkMask
IpAddress,
fsOspfNetWorkStatus
RowStatus
}
fsOspfNetWorkAreaID OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"area ID"
::= { fsOspfAddressScopeEntry 1 }
fsOspfNetWorkAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Routing for Networks Ipaddress"
::= { fsOspfAddressScopeEntry 2 }
fsOspfNetWorkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Routing for Networks mask"
::= { fsOspfAddressScopeEntry 3 }
fsOspfNetWorkStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" when this value is destroy,the
entry will be deleted"
::= { fsOspfAddressScopeEntry 4 }
-- The Ospf Interface Configuration Table
fsOspfIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Interface Table describes the interfaces
from the viewpoint of OSPF."
REFERENCE
"ospfIfTable in rfc1850"
::= { fsOspfMIBObjects 4 }
fsOspfIfEntry OBJECT-TYPE
SYNTAX FSOspfIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Interface Entry describes one inter-
face configuration of OSPF."
INDEX { fsOspfIfIpAddress, fsOspfAddressLessIf }
::= { fsOspfIfTable 1 }
FSOspfIfEntry ::=
SEQUENCE {
fsOspfIfIpAddress
IpAddress,
fsOspfAddressLessIf
Unsigned32,
fsOspfIfAreaId
AreaID,
fsOspfIfType
INTEGER,
fsOspfIfAdminStat
Status,
fsOspfIfRtrPriority
DesignatedRouterPriority,
fsOspfIfTransitDelay
Unsigned32,
fsOspfIfRetransInterval
Unsigned32,
fsOspfIfHelloInterval
HelloRange,
fsOspfIfRtrDeadInterval
PositiveInteger,
fsOspfIfPollInterval
PositiveInteger,
fsOspfIfState
INTEGER,
fsOspfIfDesignatedRouter
IpAddress,
fsOspfIfBackupDesignatedRouter
IpAddress,
fsOspfIfEvents
Counter32,
fsOspfIfAuthType
INTEGER,
fsOspfIfAuthKey
OCTET STRING,
fsOspfIfStatus
RowStatus,
fsOspfIfMulticastForwarding
INTEGER,
fsOspfIfDemand
TruthValue,
fsOspfIfDatabaseFilterAllOut
EnabledStatus,
fsOspfIfDesignateRouterId
IpAddress,
fsOspfIfBackupDesignateRouterId
IpAddress,
fsOspfIfWaitInternal
TimeTicks,
fsOspfIfPassiveStatus
EnabledStatus,
fsOspfIfCurrentUsedMd5AuthKeyId
Unsigned32
}
fsOspfIfIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of this OSPF interface."
::= { fsOspfIfEntry 1 }
fsOspfAddressLessIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP Addresses, and the corresponding value of
ifIndex for interfaces having no IP Address."
::= { fsOspfIfEntry 2 }
fsOspfIfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0.0.0.0 is used for the OSPF backbone."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { fsOspfIfEntry 3 }
fsOspfIfType OBJECT-TYPE
SYNTAX INTEGER {
broadcast (1),
nbma (2),
pointToPoint (3),
pointToMultipoint (5),
loopback(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The OSPF interface type.
By way of a default, this field may be intuited
from the corresponding value of ifType. Broad-
cast LANs, such as Ethernet and IEEE 802.5,
take the value 'broadcast', X.25 and similar
technologies take the value 'nbma', and links
that are definitively point to point take the
value 'pointToPoint'."
::= { fsOspfIfEntry 4 }
fsOspfIfAdminStat OBJECT-TYPE
SYNTAX Status
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The OSPF interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to OSPF."
::= { fsOspfIfEntry 5 }
fsOspfIfRtrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not eligi-
ble to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker."
DEFVAL { 1 }
::= { fsOspfIfEntry 6 }
fsOspfIfTransitDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link state update packet over this
interface."
DEFVAL { 1 }
::= { fsOspfIfEntry 7 }
fsOspfIfRetransInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets."
DEFVAL { 5 }
::= { fsOspfIfEntry 8 }
fsOspfIfHelloInterval OBJECT-TYPE
SYNTAX HelloRange
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for all
routers attached to a common network."
DEFVAL { 10 }
::= { fsOspfIfEntry 9 }
fsOspfIfRtrDeadInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for all routers attached
to a common network."
DEFVAL { 40 }
::= { fsOspfIfEntry 10 }
fsOspfIfPollInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The larger time interval, in seconds, between
the Hello packets sent to an inactive non-
broadcast multi- access neighbor."
::= { fsOspfIfEntry 11 }
fsOspfIfState OBJECT-TYPE
SYNTAX INTEGER {
down (1),
loopback (2),
waiting (3),
pointToPoint (4),
designatedRouter (5),
backupDesignatedRouter (6),
otherDesignatedRouter (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The OSPF Interface State."
DEFVAL { down }
::= { fsOspfIfEntry 12 }
fsOspfIfDesignatedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP Address of the interface which connected the local router in
the Designated Router."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { fsOspfIfEntry 13 }
fsOspfIfBackupDesignatedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP Address of the interface which connected the local router in
the Backup Designated Router."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { fsOspfIfEntry 14 }
fsOspfIfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this OSPF interface has
changed its state, or an error has occurred."
::= { fsOspfIfEntry 15 }
fsOspfIfAuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Authentication Key. If the Area's Author-
ization Type is simplePassword, and the key
length is shorter than 8 octets, the agent will
left adjust and zero fill to 8 octets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, fsOspfIfAuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0
::= { fsOspfIfEntry 16 }
fsOspfIfStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value will be active(1) always."
::= { fsOspfIfEntry 17 }
fsOspfIfMulticastForwarding OBJECT-TYPE
SYNTAX INTEGER {
blocked (1), -- no multicast forwarding
multicast (2), -- using multicast address
unicast (3) -- to each OSPF neighbor
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link uni-
casts. Data link multicasting is not meaning-
ful on point to point and NBMA interfaces, and
setting ospfMulticastForwarding to 0 effective-
ly disables all multicast forwarding."
DEFVAL { blocked }
::= { fsOspfIfEntry 18 }
fsOspfIfDemand OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Demand OSPF procedures (hel-
lo supression to FULL neighbors and setting the
DoNotAge flag on proogated LSAs) should be per-
formed on this interface."
DEFVAL { false }
::= { fsOspfIfEntry 19 }
fsOspfIfAuthType OBJECT-TYPE
SYNTAX INTEGER (0..255)
-- none (0),
-- simplePassword (1)
-- md5 (2)
-- default (3)
-- reserved for specification by IANA (> 2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The authentication type specified for an interface. Setting this value to
'default' means using default authentication type referenced to Area Authentication,
this value only for set,not be read. Additional authentication types may
be assigned locally."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { fsOspfIfEntry 20 }
fsOspfIfDatabaseFilterAllOut OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Block flooding of OSPF LSA packets to the interface. By
default, OSPF floods new LSAs over all interfaces in the same area,
except the interface on which the LSA arrives."
DEFVAL {disabled}
::= { fsOspfIfEntry 21 }
fsOspfIfDesignateRouterId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"DR RouterID of this interface,
when DR does not selected,DR Id is 0.0.0.0"
DEFVAL {'00000000'H}
::= { fsOspfIfEntry 22 }
fsOspfIfBackupDesignateRouterId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Backup DR RouterId of this interface ,
when Backup DR does not selected,BDR Id is 0.0.0.0"
DEFVAL {'00000000'H}
::= { fsOspfIfEntry 23 }
fsOspfIfWaitInternal OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The wait time of hello generate"
::= { fsOspfIfEntry 24 }
fsOspfIfPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object value to 'enabled' ,the interface will
become a passive interface."
DEFVAL { disabled }
::= { fsOspfIfEntry 25 }
fsOspfIfCurrentUsedMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"key-id which current used for md5 authentication,this value is
valid from 1 to 255, the value 0 is default value.."
DEFVAL {0}
::= { fsOspfIfEntry 26 }
-- The Ospf Interface MD5 authentication key configuration table
fsOspfIfMd5AuthKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration table of the key-id for md5 authentication for OSPF protocol."
::= { fsOspfMIBObjects 5 }
fsOspfIfMd5AuthKeyEntry OBJECT-TYPE
SYNTAX FSOspfIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration entry of the key-id for md5 authentication for OSPF protocol"
INDEX {fsOspfIfMd5AuthKeyIf, fsOspfIfMd5AuthKeyId }
::= { fsOspfIfMd5AuthKeyTable 1 }
FSOspfIfMd5AuthKeyEntry ::=
SEQUENCE {
fsOspfIfMd5AuthKeyIf
Unsigned32,
fsOspfIfMd5AuthKeyId
Unsigned32,
fsOspfIfMd5AuthKey
OCTET STRING,
fsOspfIfMd5AuthKeySt
ConfigStatus
}
fsOspfIfMd5AuthKeyIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Corresponding value of ifIndex for interfaces."
::= { fsOspfIfMd5AuthKeyEntry 1 }
fsOspfIfMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the key-id for md5 authentication."
::= { fsOspfIfMd5AuthKeyEntry 2 }
fsOspfIfMd5AuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Authentication Key for MD5.
When read, fsOspfIfMd5AuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
::= { fsOspfIfMd5AuthKeyEntry 3 }
fsOspfIfMd5AuthKeySt OBJECT-TYPE
SYNTAX ConfigStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Setting this value to 'invalid' will delete this entry.
Setting this value to 'valid' will have no effect."
::= { fsOspfIfMd5AuthKeyEntry 4 }
-- The FS Ospf Virtual Link Table
fsOspfVirtTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfVirtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about this router's virtual inter-
faces.Include ospfVirtIfTable in rfc1850"
REFERENCE
"ospfVirtIfTable in rfc1850"
::= { fsOspfMIBObjects 6 }
fsOspfVirtEntry OBJECT-TYPE
SYNTAX FSOspfVirtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Virtual Interface"
INDEX {fsOspfVirtIfAreaId, fsOspfVirtIfNeighbor}
::= { fsOspfVirtTable 1 }
FSOspfVirtEntry ::=
SEQUENCE {
fsOspfVirtIfAreaId
AreaID,
fsOspfVirtIfNeighbor
RouterID,
fsOspfVirtIfTransitDelay
Unsigned32,
fsOspfVirtIfRetransInterval
Unsigned32,
fsOspfVirtIfHelloInterval
HelloRange,
fsOspfVirtIfRtrDeadInterval
PositiveInteger,
fsOspfVirtIfState
INTEGER,
fsOspfVirtIfEvents
Counter32,
fsOspfVirtIfAuthType
INTEGER,
fsOspfVirtIfAuthKey
OCTET STRING,
fsOspfVirtIfStatus
RowStatus,
fsOspfVirtCost
Unsigned32,
fsOspfVirtNativeIfIndex
INTEGER,
fsOspfVirtLinkState
INTEGER,
fsOspfVirtHelloDueIn
TimeTicks,
fsOspfVirtCurrentUsedMd5AuthKeyId
Unsigned32
}
fsOspfVirtIfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0"
::= { fsOspfVirtEntry 1 }
fsOspfVirtIfNeighbor OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Virtual Neighbor."
::= { fsOspfVirtEntry 2 }
fsOspfVirtIfTransitDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link- state update packet over this
interface."
DEFVAL { 1 }
::= { fsOspfVirtEntry 3 }
fsOspfVirtIfRetransInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets. This
value should be well over the expected round-
trip time."
DEFVAL { 5 }
::= { fsOspfVirtEntry 4 }
fsOspfVirtIfHelloInterval OBJECT-TYPE
SYNTAX HelloRange
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for the
virtual neighbor."
DEFVAL { 10 }
::= { fsOspfVirtEntry 5 }
fsOspfVirtIfRtrDeadInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for the virtual neigh-
bor."
DEFVAL { 40 }
::= { fsOspfVirtEntry 6 }
fsOspfVirtIfState OBJECT-TYPE
SYNTAX INTEGER {
down (1), -- these use the same encoding
pointToPoint (4) -- as the ospfIfTable
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"OSPF virtual interface states."
DEFVAL { down }
::= { fsOspfVirtEntry 7 }
fsOspfVirtIfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of state changes or error events on
this Virtual Link"
::= { fsOspfVirtEntry 8 }
fsOspfVirtIfAuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If Authentication Type is simplePassword, the
device will left adjust and zero fill to 8 oc-
tets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, ospfVifAuthKey always returns a
string of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0
::= { fsOspfVirtEntry 9 }
fsOspfVirtIfStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { fsOspfVirtEntry 10 }
fsOspfVirtIfAuthType OBJECT-TYPE
SYNTAX INTEGER (0..255)
-- none (0),
-- simplePassword (1),
-- md5 (2),
-- default (3)
-- reserved for specification by IANA (> 2)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication type specified for a virtual interface. Setting this value
'default' means using default authentication type referenced to Area Authentication,
this value only for set,not be read. Additional authentication types
may be assigned locally."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { fsOspfVirtEntry 11 }
fsOspfVirtCost OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Explicitly specify the cost of sending a packet on the
interface."
::= { fsOspfVirtEntry 12 }
fsOspfVirtNativeIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the Interface's Index that The Virtual Link
via this interface."
::= { fsOspfVirtEntry 13 }
fsOspfVirtLinkState OBJECT-TYPE
SYNTAX INTEGER{
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Virtual Link State is up or down."
::= { fsOspfVirtEntry 14 }
fsOspfVirtHelloDueIn OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the time when hello due in."
::= { fsOspfVirtEntry 15 }
fsOspfVirtCurrentUsedMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"the key-id which current used for md5 authentication,this value is
valid from 1 to 255, the value 0 is default value."
DEFVAL {0}
::= { fsOspfVirtEntry 16 }
-- The Ospf Virtual Interface MD5 authentication key configuration table
fsOspfVirtIfMd5AuthKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfVirtIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration table of the key-id for md5 authentication in VirtIf
for OSPF protocol."
::= { fsOspfMIBObjects 7 }
fsOspfVirtIfMd5AuthKeyEntry OBJECT-TYPE
SYNTAX FSOspfVirtIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration entry of the key-id for md5 authentication in VirtIf
for OSPF protocol"
INDEX {fsOspfVirtIfMd5AuthKeyAreaId, fsOspfVirtIfMd5AuthKeyNeighbor,
fsOspfVirtIfMd5AuthKeyId }
::= { fsOspfVirtIfMd5AuthKeyTable 1 }
FSOspfVirtIfMd5AuthKeyEntry ::=
SEQUENCE {
fsOspfVirtIfMd5AuthKeyAreaId
AreaID,
fsOspfVirtIfMd5AuthKeyNeighbor
RouterID,
fsOspfVirtIfMd5AuthKeyId
Unsigned32,
fsOspfVirtIfMd5AuthKey
OCTET STRING,
fsOspfVirtIfMd5AuthKeySt
ConfigStatus
}
fsOspfVirtIfMd5AuthKeyAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0"
::= { fsOspfVirtIfMd5AuthKeyEntry 1 }
fsOspfVirtIfMd5AuthKeyNeighbor OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Virtual Neighbor."
::= { fsOspfVirtIfMd5AuthKeyEntry 2 }
fsOspfVirtIfMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the key-id for md5 authentication."
::= { fsOspfVirtIfMd5AuthKeyEntry 3 }
fsOspfVirtIfMd5AuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Authentication Key for MD5.
When read, fsOspfVirtIfMd5AuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
::= { fsOspfVirtIfMd5AuthKeyEntry 4 }
fsOspfVirtIfMd5AuthKeySt OBJECT-TYPE
SYNTAX ConfigStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Setting this value to 'invalid' will delete this entry.
Setting this value to 'valid' will have no effect."
::= { fsOspfVirtIfMd5AuthKeyEntry 5 }
fsOspfLsaDetailInfoMibsGroup OBJECT IDENTIFIER ::= { fsOspfMIBObjects 8 }
-- OSPF Link State Database
-- The Link State Database contains the Link State
-- Advertisements from throughout the areas that the
-- device is attached to.
fsOspfLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Process's Link State Database."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { fsOspfLsaDetailInfoMibsGroup 1 }
fsOspfLsdbEntry OBJECT-TYPE
SYNTAX FSOspfLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Link State Advertisement."
INDEX { fsOspfLsdbAreaId, fsOspfLsdbType,
fsOspfLsdbLsid, fsOspfLsdbRouterId }
::= { fsOspfLsdbTable 1 }
FSOspfLsdbEntry ::=
SEQUENCE {
fsOspfLsdbAreaId
AreaID,
fsOspfLsdbType
INTEGER,
fsOspfLsdbLsid
IpAddress,
fsOspfLsdbRouterId
RouterID,
fsOspfLsdbSequence
Unsigned32,
fsOspfLsdbAge
Unsigned32,
fsOspfLsdbChecksum
Unsigned32,
fsOspfLsdbAdvertisement
OCTET STRING,
fsOspfLsdbLinkNum --equal LinkCount
Unsigned32,
fsOspfLsdbPacketLength
Unsigned32,
fsOspfSummaryLsaNetworkMask
IpAddress,
fsOspfSummaryLsaTos0Metric
Unsigned32,
fsOspfNssaLsaDetailMetricType
INTEGER,
fsOspfNssaLsaDetailForwardAddr
IpAddress,
fsOspfNssaLsaDetailRouteTag
Unsigned32,
fsOspfLsdbOption
Unsigned32
}
fsOspfLsdbAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit identifier of the Area from which
the LSA was received."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { fsOspfLsdbEntry 1 }
-- External Link State Advertisements are permitted
-- for backward compatibility, but should be displayed in
-- the ospfExtLsdbTable rather than here.
fsOspfLsdbType OBJECT-TYPE
SYNTAX INTEGER {
routerLink (1),
networkLink (2),
summaryLink (3),
asSummaryLink (4),
asExternalLink (5), -- but see fsOspfExtLsdbTable
multicastLink (6),
nssaExternalLink (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate advertise-
ment format."
REFERENCE
"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"
::= { fsOspfLsdbEntry 2 }
fsOspfLsdbLsid OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.4 Link State ID"
::= { fsOspfLsdbEntry 3 }
fsOspfLsdbRouterId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { fsOspfLsdbEntry 4 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It fss with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
fsOspfLsdbSequence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { fsOspfLsdbEntry 5 }
fsOspfLsdbAge OBJECT-TYPE
SYNTAX Unsigned32 -- Should be 0..MaxAge
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state adver-
tisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { fsOspfLsdbEntry 6 }
fsOspfLsdbChecksum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { fsOspfLsdbEntry 7 }
fsOspfLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { fsOspfLsdbEntry 8 }
fsOspfLsdbLinkNum OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the link count of this Router Link Lsa ,
this field is only valid for Router Link Lsa<73><61>type 1 LSA)"
::= { fsOspfLsdbEntry 9 }
fsOspfLsdbPacketLength OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the lsa packet length ."
::= { fsOspfLsdbEntry 10 }
fsOspfSummaryLsaNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is only useful when ospfLsdbType is type-3 or
type-4 or type-7,it's the Lsa's network mask ."
::= { fsOspfLsdbEntry 11 }
fsOspfSummaryLsaTos0Metric OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is only useful when ospfLsdbType is type-3 or
type-4 or type-7,it's the Lsa's tos0 metric ."
::= { fsOspfLsdbEntry 12 }
fsOspfNssaLsaDetailMetricType OBJECT-TYPE
SYNTAX INTEGER
{ type1(1),
type2(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" this field is valid when Lsa is a type-7 LSA.
The type of Nssa ernal metric. If bit E is set, the metric
specified is a Type 2 external metric. This means the metric is
considered larger than any link state path. If bit E is zero,
the specified metric is a Type 1 external metric. This means
that it is expressed in the same units as the link state metric
(i.e., the same units as interface cost). "
::= { fsOspfLsdbEntry 13 }
fsOspfNssaLsaDetailForwardAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is valid when Lsa is a type-7 LSA.
Data traffic for the advertised destination will be forwarded to
this address. If the Forwarding address is set to 0.0.0.0, data
traffic will be forwarded instead to the LSA's originator (i.e.,
the responsible AS boundary router) ."
::= { fsOspfLsdbEntry 14 }
fsOspfNssaLsaDetailRouteTag OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" this field is valid when Lsa is a type-7 LSA.
A 32-bit field attached to each external route. This is not
used by the OSPF protocol itself. It may be used to communicate
information between AS boundary routers; the precise nature of
such information is outside the scope of this specification."
::= { fsOspfLsdbEntry 15 }
fsOspfLsdbOption OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the option field indicate which optional capabilities
area associated with the LSA. "
REFERENCE
"OSPF Version 2, Appendix A.2, the Options Field"
::= { fsOspfLsdbEntry 16 }
-- OSPF Link State Database, External
-- The Link State Database contains the Link State
-- Advertisements from throughout the areas that the
-- device is attached to.
-- This table is identical to the OSPF LSDB Table in
-- format, but contains only External Link State
-- Advertisements. The purpose is to allow external
-- LSAs to be displayed once for the router rather
-- than once in each non-stub area.
fsOspfExtLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfExtLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Process's Links State Database."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { fsOspfLsaDetailInfoMibsGroup 2 }
fsOspfExtLsdbEntry OBJECT-TYPE
SYNTAX FSOspfExtLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Link State Advertisement."
INDEX { fsOspfExtLsdbType, fsOspfExtLsdbLsid, fsOspfExtLsdbRouterId }
::= { fsOspfExtLsdbTable 1 }
FSOspfExtLsdbEntry ::=
SEQUENCE{
fsOspfExtLsdbType
INTEGER,
fsOspfExtLsdbLsid
IpAddress,
fsOspfExtLsdbRouterId
RouterID,
fsOspfExtLsdbSequence
Unsigned32,
fsOspfExtLsdbAge
Unsigned32,
fsOspfExtLsdbChecksum
Unsigned32,
fsOspfExtLsdbAdvertisement
OCTET STRING,
fsOspfExtLsdbNetworkMask
IpAddress,
fsOspfExtLsdbMetricType
INTEGER,
fsOspfExtLsdbForwardAddr
IpAddress,
fsOspfExtLsdbRouteTag
Unsigned32,
fsOspfExtLsdbMetric
INTEGER,
fsOspfExtLsdbOption
Unsigned32,
fsOspfExtLsdbPacketLength
Unsigned32
}
fsOspfExtLsdbType OBJECT-TYPE
SYNTAX INTEGER {
asExternalLink (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate advertise-
ment format."
REFERENCE
"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"
::= { fsOspfExtLsdbEntry 1 }
fsOspfExtLsdbLsid OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.4 Link State ID"
::= { fsOspfExtLsdbEntry 2 }
fsOspfExtLsdbRouterId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { fsOspfExtLsdbEntry 3 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It fss with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
fsOspfExtLsdbSequence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { fsOspfExtLsdbEntry 4 }
fsOspfExtLsdbAge OBJECT-TYPE
SYNTAX Unsigned32 -- Should be 0..MaxAge
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state adver-
tisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { fsOspfExtLsdbEntry 5 }
fsOspfExtLsdbChecksum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { fsOspfExtLsdbEntry 6 }
fsOspfExtLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(36))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { fsOspfExtLsdbEntry 7 }
fsOspfExtLsdbNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address mask for the advertised destination. For
example, when advertising a class A network the mask 0xff000000
would be used."
::= { fsOspfExtLsdbEntry 8 }
fsOspfExtLsdbMetric OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The cost of this route. Interpretation depends on the external
type indication. "
::= { fsOspfExtLsdbEntry 9 }
fsOspfExtLsdbMetricType OBJECT-TYPE
SYNTAX INTEGER
{ type1(1),
type2(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The type of external metric. If bit E is set, the metric
specified is a Type 2 external metric. This means the metric is
considered larger than any link state path. If bit E is zero,
the specified metric is a Type 1 external metric. This means
that it is expressed in the same units as the link state metric
(i.e., the same units as interface cost). "
::= { fsOspfExtLsdbEntry 10 }
fsOspfExtLsdbForwardAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Data traffic for the advertised destination will be forwarded to
this address. If the Forwarding address is set to 0.0.0.0, data
traffic will be forwarded instead to the LSA's originator (i.e.,
the responsible AS boundary router) ."
::= { fsOspfExtLsdbEntry 11 }
fsOspfExtLsdbRouteTag OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit field attached to each external route. This is not
used by the OSPF protocol itself. It may be used to communicate
information between AS boundary routers; the precise nature of
such information is outside the scope of this specification."
::= { fsOspfExtLsdbEntry 12 }
fsOspfExtLsdbOption OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the option field indicate which optional capabilities
area associated with the LSA. "
REFERENCE
"OSPF Version 2, Appendix A.2, the Options Field"
::= { fsOspfExtLsdbEntry 13 }
fsOspfExtLsdbPacketLength OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the lsa packet length ."
::= { fsOspfExtLsdbEntry 14 }
--Router Lsa's detail information table
fsOspfRouterLsaDetailTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfRouterLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the router Lsa's detail Infromtion."
::= { fsOspfLsaDetailInfoMibsGroup 3 }
fsOspfRouterLsaDetailEntry OBJECT-TYPE
SYNTAX FSOspfRouterLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {fsOspfLsdbAreaId, fsOspfLsdbType,
fsOspfLsdbLsid, fsOspfLsdbRouterId,
fsOspfRouterLsaDetailLinkID
}
::= { fsOspfRouterLsaDetailTable 1 }
FSOspfRouterLsaDetailEntry ::=
SEQUENCE{
fsOspfRouterLsaDetailLinkID
IpAddress,
fsOspfRouterLsaDetailLinkType
INTEGER,
fsOspfRouterLsaDetailLinkData
IpAddress,
fsOspfRouterLsaDetailTos0Metric
Unsigned32
}
fsOspfRouterLsaDetailLinkID OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"router lsa's link ID Identifies the object that this router
link connects to. Value depends on the link's Type.
When connecting to an object that also originates an
LSA (i.e., another router or a transit network) the
Link ID is equal to the neighboring LSA's Link
State ID. This provides the key for looking up the neighboring
LSA in the link state database during the routing table
calculation. See Section 12.2 for more details.
Type Link ID
________________________________________
1 Neighboring router's Router ID
2 IP address of Designated Router
3 IP network/subnet number
4 Neighboring router's Router ID
"
::= { fsOspfRouterLsaDetailEntry 1 }
fsOspfRouterLsaDetailLinkType OBJECT-TYPE
SYNTAX INTEGER{
pointtopointConnectionToAnotherRouter(1),
connectionToaTransitNetwork(2),
connectionToaStubNetwork(3),
virtualLink(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"router lsa's link type
A quick description of the router link. One of the following.
Note that host routes are classified as links to stub networks
with network mask of 0xffffffff."
::= { fsOspfRouterLsaDetailEntry 2 }
fsOspfRouterLsaDetailLinkData OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Value again depends on the link's Type field. For connections to
stub networks, Link Data specifies the network's IP address
mask. For unnumbered point-to-point connections, it specifies
the interface's MIB-II ifIndex value. For the other link
types it specifies the router interface's IP address. This
latter piece of information is needed during the routing table
build process, when calculating the IP address of the next hop. "
::= { fsOspfRouterLsaDetailEntry 3 }
fsOspfRouterLsaDetailTos0Metric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"TOS0-specific metric information."
::= { fsOspfRouterLsaDetailEntry 4 }
--NetWork Lsa's detail information table
fsOspfNetWorkLsaDetailTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfNetWorkLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the NetWork Lsa's detail Infromtion."
::= { fsOspfLsaDetailInfoMibsGroup 4 }
fsOspfNetWorkLsaDetailEntry OBJECT-TYPE
SYNTAX FSOspfNetWorkLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {fsOspfLsdbAreaId, fsOspfLsdbType,
fsOspfLsdbLsid, fsOspfLsdbRouterId,
fsOspfNetWorkLsaDetailAttachedRouter
}
::= { fsOspfNetWorkLsaDetailTable 1 }
FSOspfNetWorkLsaDetailEntry ::=
SEQUENCE{
fsOspfNetWorkLsaDetailAttachedRouter
IpAddress,
fsOspfNetWorkLsaDetailNetworkMask
IpAddress
}
fsOspfNetWorkLsaDetailAttachedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The Router IDs of each of the routers attached to the network.
Actually, only those routers that are fully adjacent to the
Designated Router are listed. The Designated Router includes
itself in this list. The number of routers included can be
deduced from the LSA header's length field. "
::= { fsOspfNetWorkLsaDetailEntry 1 }
fsOspfNetWorkLsaDetailNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address mask for the network. For example, a class A
network would have the mask 0xff000000."
::= { fsOspfNetWorkLsaDetailEntry 2 }
--fs Ospf Area Lsa Database Summary Table
fsOspfAreaLsaDBSumTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfAreaLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Area LSA database summary Infromtion."
::= { fsOspfLsaDetailInfoMibsGroup 5 }
fsOspfAreaLsaDBSumEntry OBJECT-TYPE
SYNTAX FSOspfAreaLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {fsOspfAreaLsaDBSumAreaId,
fsOspfAreaLsaDBSumLsaType
}
::= { fsOspfAreaLsaDBSumTable 1 }
FSOspfAreaLsaDBSumEntry ::=
SEQUENCE{
fsOspfAreaLsaDBSumAreaId
IpAddress,
fsOspfAreaLsaDBSumLsaType
INTEGER,
fsOspfAreaLsaDBSumCounts
Counter32,
fsOspfAreaLsaDBSumDeletes
Counter32,
fsOspfAreaLsaDBSumMaxage
Counter32
}
fsOspfAreaLsaDBSumAreaId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The area Id."
::= { fsOspfAreaLsaDBSumEntry 1 }
fsOspfAreaLsaDBSumLsaType OBJECT-TYPE
SYNTAX INTEGER
{ routerLink (1),
networkLink (2),
summaryLink (3),
asSummaryLink (4),
--asExternalLink (5), because in each area,type 5 lsa is no meaning
--it's only meaning in one router
-- multicastLink (6), not implement
nssaExternalLink (7),
subtotal(8)
--subtotal is use for total counter for all type LSA in this area.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the entry's entry type."
::= { fsOspfAreaLsaDBSumEntry 2 }
fsOspfAreaLsaDBSumCounts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number os this type Lsa in this area ,
if this type Lsa does not exist,this field is 0."
::= { fsOspfAreaLsaDBSumEntry 3 }
fsOspfAreaLsaDBSumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number os this type Lsa which has been delete in this area ,
if this type Lsa is not been deleted,this field is 0"
::= { fsOspfAreaLsaDBSumEntry 4 }
fsOspfAreaLsaDBSumMaxage OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number of this type Lsa which has up to Maxage,
if this type Lsa which has up to Maxage does not exist,
this field is 0"
::= { fsOspfAreaLsaDBSumEntry 5 }
--fs Ospf Lsa Database total summary table
fsOspfLsaDBSumTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"LSA database total summary infromtion in the all areas ."
::= { fsOspfLsaDetailInfoMibsGroup 6 }
fsOspfLsaDBSumEntry OBJECT-TYPE
SYNTAX FSOspfLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {
fsOspfLsaDBSumLsaType
}
::= { fsOspfLsaDBSumTable 1 }
FSOspfLsaDBSumEntry ::=
SEQUENCE{
fsOspfLsaDBSumLsaType
INTEGER,
fsOspfLsaDBSumCounts
Counter32,
fsOspfLsaDBSumDeletes
Counter32,
fsOspfLsaDBSumMaxage
Counter32
}
fsOspfLsaDBSumLsaType OBJECT-TYPE
SYNTAX INTEGER
{ routerLink (1),
networkLink (2),
summaryTotalLink (3),
asSummaryTotalLink (4),
asExternalLink (5),
-- multicastLink (6), not implement
nssaExternalLink (7),
total(8)
--subtotal is use for total counter for all type LSA in this router.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the table's entry type."
::= { fsOspfLsaDBSumEntry 1 }
fsOspfLsaDBSumCounts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"total number of this type Lsa in all area ."
::= { fsOspfLsaDBSumEntry 2 }
fsOspfLsaDBSumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" total number of this type Lsa deleted in all area ."
::= { fsOspfLsaDBSumEntry 3 }
fsOspfLsaDBSumMaxage OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"total number of this type Lsa which has been up to max age in all area "
::= { fsOspfLsaDBSumEntry 4 }
-- The OSPF Neighbor Table describes all neighbors in
-- the locality of the subject router.
fsOspfNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the neighbor detail infomation ."
REFERENCE
"ospfNbrTable in rfc1850"
::= { fsOspfMIBObjects 9 }
fsOspfNeighborEntry OBJECT-TYPE
SYNTAX FSOspfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX { fsOspfNbrIpAddr,
fsOspfNbrAddressLessIndex
}
::= { fsOspfNeighborTable 1 }
FSOspfNeighborEntry ::=
SEQUENCE{
fsOspfNbrIpAddr
IpAddress,
fsOspfNbrAddressLessIndex
Unsigned32,
fsOspfNbrRtrId
RouterID,
fsOspfNbrOptions
Unsigned32,
fsOspfNbrPriority
DesignatedRouterPriority,
fsOspfNbrState
INTEGER,
fsOspfNbrEvents
Counter32,
fsOspfNbrLsRetransQLen
Gauge32,
fsOspfNbmaNbrStatus
RowStatus,
fsOspfNbmaNbrPermanence
INTEGER,
fsOspfNbrHelloSuppressed
TruthValue,
fsOspfNbrDeadTimeDueIn
TimeTicks,
fsOspfNbrNeighborUpTime
TimeTicks,
fsOspfNbrDR
IpAddress,
fsOspfNbrBDR
IpAddress,
fsOspfNbrArea
IpAddress,
fsOspfNbrRetransmissionNum
Counter32,
fsOspfNbrIfState
INTEGER
}
fsOspfNbrIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address this neighbor(neighbor's interface IP address)
is using in its IP Source Address. Note that, on addressless
links, this will not be 0.0.0.0, but the ad-
dress of another of the neighbor's interfaces."
::= { fsOspfNeighborEntry 1 }
fsOspfNbrAddressLessIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"On an interface having an IP Address, zero.
On addressless interfaces, the corresponding
value of ifIndex in the Internet Standard MIB.
On row creation, this can be derived from the
instance."
::= { fsOspfNeighborEntry 2 }
fsOspfNbrRtrId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer (represented as a type IpAd-
dress) uniquely identifying the neighboring
router in the Autonomous System."
::= { fsOspfNeighborEntry 3 }
fsOspfNbrOptions OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A Bit Mask corresponding to the neighbor's op-
tions field.
Bit 0, if set, indicates that the system will
operate on Type of Service metrics other than
TOS 0. If zero, the neighbor will ignore all
metrics except the TOS 0 metric.
Bit 1, if set, indicates that the associated
area accepts and operates on external informa-
tion; if zero, it is a stub area.
Bit 2, if set, indicates that the system is ca-
pable of routing IP Multicast datagrams; i.e.,
that it implements the Multicast Extensions to
OSPF.
Bit 3, if set, indicates that the associated
area is an NSSA. These areas are capable of
carrying type 7 external advertisements, which
are translated into type 5 external advertise-
ments at NSSA borders."
REFERENCE
"OSPF Version 2, Section 12.1.2 Options"
::= { fsOspfNeighborEntry 4 }
fsOspfNbrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The priority of this neighbor in the designat-
ed router election algorithm. The value 0 sig-
nifies that the neighbor is not eligible to be-
come the designated router on this particular
network."
::= { fsOspfNeighborEntry 5 }
fsOspfNbrState OBJECT-TYPE
SYNTAX INTEGER {
down (1),
attempt (2),
init (3),
twoWay (4),
exchangeFS (5),
exchange (6),
loading (7),
full (8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The State of the relationship with this Neigh-
bor."
REFERENCE
"OSPF Version 2, Section 10.1 Neighbor States"
::= { fsOspfNeighborEntry 6 }
fsOspfNbrEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this neighbor relationship
has changed state, or an error has occurred."
::= { fsOspfNeighborEntry 7 }
fsOspfNbrLsRetransQLen OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current length of the retransmission
queue."
::= { fsOspfNeighborEntry 8 }
fsOspfNbmaNbrStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { fsOspfNeighborEntry 9 }
fsOspfNbmaNbrPermanence OBJECT-TYPE
SYNTAX INTEGER {
dynamic (1), -- learned through protocol
permanent (2) -- configured address
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. 'dynamic' and 'permanent' refer to how
the neighbor became known."
::= { fsOspfNeighborEntry 10 }
fsOspfNbrHelloSuppressed OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Hellos are being suppressed
to the neighbor"
::= { fsOspfNeighborEntry 11 }
fsOspfNbrDeadTimeDueIn OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"if in this interval ,hello packet is not been received ,
the neighbor is recognized dead.if received,it
will recovery the dead time which has been setted."
::= { fsOspfNeighborEntry 12 }
fsOspfNbrNeighborUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the time that the neighbor has been up."
::= { fsOspfNeighborEntry 13 }
fsOspfNbrDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Designated Router of this neighbor."
::= { fsOspfNeighborEntry 14 }
fsOspfNbrBDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Backup Designated Router of this neighbor."
::= { fsOspfNeighborEntry 15 }
fsOspfNbrArea OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the area where the neighbor is in."
::= { fsOspfNeighborEntry 16 }
fsOspfNbrRetransmissionNum OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Retransmission times."
::= { fsOspfNeighborEntry 17 }
fsOspfNbrIfState OBJECT-TYPE
SYNTAX INTEGER {
other(0),
designatedRouter (1),
backupDesignatedRouter (2),
otherDesignatedRouter (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The neighbor's interface State which connected to local router."
::= { fsOspfNeighborEntry 18 }
--OSPF border routing information
fsOspfRouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSOspfRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entity's OSPF border routing table."
::= { fsOspfMIBObjects 10 }
fsOspfRouteEntry OBJECT-TYPE
SYNTAX FSOspfRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A route to a destination."
INDEX {
fsOspfRouteDest,
fsOspfRouteArea,
fsOspfRouteNextHop
}
::= { fsOspfRouteTable 1 }
FSOspfRouteEntry ::=
SEQUENCE {
fsOspfRouteDest
IpAddress,
fsOspfRouteArea
IpAddress,
fsOspfRouteNextHop
IpAddress,
fsOspfRouteCost
Unsigned32,
fsOspfRouteType
INTEGER,
fsOspfRouteDRType
INTEGER,
fsOspfRouteSpfNo
Counter32
}
fsOspfRouteDest OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Router ID of the destination."
::= { fsOspfRouteEntry 1 }
fsOspfRouteArea OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The area ID of the area from which this route is learned."
::= { fsOspfRouteEntry 2 }
fsOspfRouteNextHop OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Next hop toward the destination."
::= { fsOspfRouteEntry 3 }
fsOspfRouteCost OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Cost of using this route."
::= { fsOspfRouteEntry 4 }
fsOspfRouteDRType OBJECT-TYPE
SYNTAX INTEGER {
abr(1),
asbr(2),
both(3) --abr and asbr
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The router type of the destination;
it is either an ABR or ASBR or both."
::= { fsOspfRouteEntry 5 }
fsOspfRouteType OBJECT-TYPE
SYNTAX INTEGER {
intral-area-route(1),
inter-area-route(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field indicate this route is an intral area route
or inter area route."
::= { fsOspfRouteEntry 6 }
fsOspfRouteSpfNo OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The internal number of the shortest path first (SPF) calculation that
installs this route."
::= { fsOspfRouteEntry 7 }
-- conformance information
fsOspfMIBConformance OBJECT IDENTIFIER ::= { fsOspfMIB 2 }
fsOspfMIBCompliances OBJECT IDENTIFIER ::= { fsOspfMIBConformance 1 }
fsOspfMIBGroups OBJECT IDENTIFIER ::= { fsOspfMIBConformance 2 }
-- compliance statements
fsOspfMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which implement
the FS OSPF MIB"
MODULE -- this module
MANDATORY-GROUPS {
fsOspfBaseMIBGroup,
fsOspfAreaMIBGroup,
fsOspfLsaMIBGroup,
fsOspfIfMIBGroup,
fsOspfVirtMIBGroup,
fsOspfNeighborMIBGroup,
fsOspfRouteInfoMIBGroup
}
::= { fsOspfMIBCompliances 1 }
-- units of conformance
fsOspfBaseMIBGroup OBJECT-GROUP
OBJECTS {
fsOspfMiniLsaInterval ,
fsOspfMiniLsaArrival ,
fsOspfAreasNum ,
fsOspfNormalAreasNum ,
fsOspfStubAreasNum ,
fsOspfNssaAreasNum ,
fsOspfSpfDelay ,
fsOspfSpfHoldTime ,
fsOspfAutoCostRefBandWidthRef ,
fsOspfLsaGroupPacing ,
fsOspfInterDistance ,
fsOspfIntraDistance ,
fsOspfExternDistance ,
fsOspfLogAdjChangeNotify ,
fsOspfPassiveStatus ,
fsOspfRFC1583Compatibility ,
fsOspfRouteRedisDefMetricVal
}
STATUS current
DESCRIPTION
"A collection of general objects providing OSPF managment."
::= { fsOspfMIBGroups 1 }
fsOspfAreaMIBGroup OBJECT-GROUP
OBJECTS {
fsOspfAreaId,
fsOspfAuthType,
fsOspfImportAsExtern,
fsOspfSpfRuns,
fsOspfAreaBdrRtrCount,
fsOspfAsBdrRtrCount,
fsOspfAreaLsaCount,
fsOspfAreaLsaCksumSum,
fsOspfAreaSummary,
fsOspfAreaStatus,
fsOspfAreaInterfaceNum,
fsOspfAreaNssaIsRedistribution,
fsOspfAreaNssaIsDefInfoOriginate,
fsOspfNetWorkAreaID,
fsOspfNetWorkAddress,
fsOspfNetWorkMask,
fsOspfNetWorkStatus
}
STATUS current
DESCRIPTION
"A collection of area objects providing OSPF managment."
::= { fsOspfMIBGroups 2 }
fsOspfLsaMIBGroup OBJECT-GROUP
OBJECTS {
fsOspfLsdbAreaId,
fsOspfLsdbType,
fsOspfLsdbLsid,
fsOspfLsdbRouterId,
fsOspfLsdbSequence,
fsOspfLsdbAge,
fsOspfLsdbChecksum,
fsOspfLsdbAdvertisement,
fsOspfLsdbLinkNum,
fsOspfLsdbPacketLength,
fsOspfSummaryLsaNetworkMask,
fsOspfSummaryLsaTos0Metric,
fsOspfNssaLsaDetailMetricType,
fsOspfNssaLsaDetailForwardAddr ,
fsOspfNssaLsaDetailRouteTag ,
fsOspfLsdbOption,
fsOspfExtLsdbType,
fsOspfExtLsdbLsid,
fsOspfExtLsdbRouterId,
fsOspfExtLsdbSequence,
fsOspfExtLsdbAge,
fsOspfExtLsdbChecksum,
fsOspfExtLsdbAdvertisement,
fsOspfExtLsdbNetworkMask,
fsOspfExtLsdbMetricType,
fsOspfExtLsdbForwardAddr,
fsOspfExtLsdbRouteTag,
fsOspfExtLsdbMetric,
fsOspfExtLsdbOption,
fsOspfExtLsdbPacketLength,
fsOspfRouterLsaDetailLinkID,
fsOspfRouterLsaDetailLinkType,
fsOspfRouterLsaDetailLinkData,
fsOspfRouterLsaDetailTos0Metric,
fsOspfNetWorkLsaDetailAttachedRouter,
fsOspfNetWorkLsaDetailNetworkMask,
fsOspfAreaLsaDBSumAreaId,
fsOspfAreaLsaDBSumLsaType,
fsOspfAreaLsaDBSumCounts ,
fsOspfAreaLsaDBSumDeletes,
fsOspfAreaLsaDBSumMaxage,
fsOspfLsaDBSumLsaType,
fsOspfLsaDBSumCounts,
fsOspfLsaDBSumDeletes,
fsOspfLsaDBSumMaxage
}
STATUS current
DESCRIPTION
"A collection of OSPF Link State Database objects providing OSPF managment."
::= { fsOspfMIBGroups 3 }
fsOspfIfMIBGroup OBJECT-GROUP
OBJECTS {
fsOspfIfIpAddress,
fsOspfAddressLessIf,
fsOspfIfAreaId,
fsOspfIfType,
fsOspfIfAdminStat,
fsOspfIfRtrPriority,
fsOspfIfTransitDelay,
fsOspfIfRetransInterval,
fsOspfIfHelloInterval,
fsOspfIfRtrDeadInterval,
fsOspfIfPollInterval,
fsOspfIfState,
fsOspfIfDesignatedRouter,
fsOspfIfBackupDesignatedRouter,
fsOspfIfEvents,
fsOspfIfAuthType,
fsOspfIfAuthKey,
fsOspfIfStatus,
fsOspfIfMulticastForwarding,
fsOspfIfDemand,
fsOspfIfDatabaseFilterAllOut,
fsOspfIfDesignateRouterId ,
fsOspfIfBackupDesignateRouterId ,
-- fsOspfIfMd5AuthKeyId,
fsOspfIfWaitInternal,
fsOspfIfPassiveStatus,
fsOspfIfCurrentUsedMd5AuthKeyId,
fsOspfIfMd5AuthKeyIf,
fsOspfIfMd5AuthKeyId,
fsOspfIfMd5AuthKey,
fsOspfIfMd5AuthKeySt
}
STATUS current
DESCRIPTION
"A collection of OSPF interface managment."
::= { fsOspfMIBGroups 4 }
fsOspfVirtMIBGroup OBJECT-GROUP
OBJECTS {
fsOspfVirtIfAreaId,
fsOspfVirtIfNeighbor,
fsOspfVirtIfTransitDelay,
fsOspfVirtIfRetransInterval,
fsOspfVirtIfHelloInterval,
fsOspfVirtIfRtrDeadInterval,
fsOspfVirtIfState,
fsOspfVirtIfEvents,
fsOspfVirtIfAuthType,
fsOspfVirtIfAuthKey,
fsOspfVirtIfStatus,
fsOspfVirtCost,
fsOspfVirtNativeIfIndex,
fsOspfVirtLinkState,
fsOspfVirtHelloDueIn,
fsOspfVirtIfMd5AuthKeyAreaId,
fsOspfVirtIfMd5AuthKeyNeighbor,
fsOspfVirtIfMd5AuthKeyId,
fsOspfVirtIfMd5AuthKey,
fsOspfVirtIfMd5AuthKeySt,
fsOspfVirtCurrentUsedMd5AuthKeyId
}
STATUS current
DESCRIPTION
"A collection of OSPF Virtual Link managment."
::= { fsOspfMIBGroups 5 }
fsOspfNeighborMIBGroup OBJECT-GROUP
OBJECTS {
fsOspfNbrIpAddr,
fsOspfNbrAddressLessIndex,
fsOspfNbrRtrId,
fsOspfNbrOptions,
fsOspfNbrPriority,
fsOspfNbrState,
fsOspfNbrEvents,
fsOspfNbrLsRetransQLen,
fsOspfNbmaNbrStatus,
fsOspfNbmaNbrPermanence,
fsOspfNbrHelloSuppressed,
fsOspfNbrDeadTimeDueIn,
fsOspfNbrNeighborUpTime,
fsOspfNbrDR,
fsOspfNbrBDR,
fsOspfNbrArea,
fsOspfNbrRetransmissionNum
}
STATUS current
DESCRIPTION
"A collection of OSPF Neighbor information."
::= { fsOspfMIBGroups 6 }
fsOspfRouteInfoMIBGroup OBJECT-GROUP
OBJECTS {
fsOspfRouteType,
fsOspfRouteDest,
fsOspfRouteNextHop,
fsOspfRouteCost,
fsOspfRouteDRType,
fsOspfRouteArea,
fsOspfRouteSpfNo
}
STATUS current
DESCRIPTION
"A collection of OSPF route information."
::= { fsOspfMIBGroups 7 }
-- -------------------------------------------------------------
-- Compliance statements
-- -------------------------------------------------------------
ospfMIBConformance OBJECT IDENTIFIER ::= { fsOspfMIB 3 }
ospfMIBCompliances OBJECT IDENTIFIER ::= { ospfMIBConformance 1 }
ospfExternCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for device support of OSPF
services."
MODULE
-- OBJECT ospfASBdrRtrStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfTOSSupport
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfExtLsdbLimit
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfMulticastExtensions
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfExitOverflowInterval
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfDemandExtensions
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfIfAreaId
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfIfStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Create access is not required."
--
--
-- OBJECT ospfStubMetric
-- MIN-ACCESS read-write
-- DESCRIPTION "Create access is not required."
--
-- OBJECT ospfStubStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfStubMetricType
-- MIN-ACCESS read-write
-- DESCRIPTION "Create access is not required."
--
-- OBJECT ospfIfAdminStat
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfNbmaNbrStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfNbrPriority
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfIfPollInterval
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfIfTransitDelay
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfIfRetransInterval
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfVirtIfTransitDelay
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfIfType
-- SYNTAX INTEGER {
-- broadcast (1),
-- nbma (2),
-- pointToPoint (3),
-- pointToMultipoint (5),
-- loopback(6)
-- }
-- DESCRIPTION "add type 'loopback'."
--
-- OBJECT ospfVirtIfRetransInterval
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
OBJECT fsOspfVirtIfRtrDeadInterval
SYNTAX PositiveInteger
DESCRIPTION "default value change from 60 to 40."
::= { ospfMIBCompliances 1 }
END
View Git Blame Copy Permalink