663 lines
24 KiB
Plaintext
663 lines
24 KiB
Plaintext
VDSL-LINE-EXT-MCM-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE,
|
|
transmission,
|
|
Unsigned32 FROM SNMPv2-SMI -- [RFC2578]
|
|
RowStatus FROM SNMPv2-TC -- [RFC2579]
|
|
MODULE-COMPLIANCE,
|
|
OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580]
|
|
vdslLineConfProfileName FROM VDSL-LINE-MIB; -- [RFC3728]
|
|
|
|
vdslExtMCMMIB MODULE-IDENTITY
|
|
LAST-UPDATED "200504280000Z" -- April 28, 2005
|
|
ORGANIZATION "ADSLMIB Working Group"
|
|
CONTACT-INFO "WG-email: adslmib@ietf.org
|
|
Info: https://www1.ietf.org/mailman/listinfo/adslmib
|
|
|
|
Chair: Mike Sneed
|
|
Sand Channel Systems
|
|
Postal: P.O. Box 37324
|
|
Raleigh NC 27627-732
|
|
Email: sneedmike@hotmail.com
|
|
Phone: +1 206 600 7022
|
|
|
|
Co-Chair/Co-editor:
|
|
Bob Ray
|
|
PESA Switching Systems, Inc.
|
|
Postal: 330-A Wynn Drive
|
|
Huntsville, AL 35805
|
|
USA
|
|
Email: rray@pesa.com
|
|
Phone: +1 256 726 9200 ext. 142
|
|
|
|
Co-editor: Menachem Dodge
|
|
ECI Telecom Ltd.
|
|
Postal: 30 hasivim St.
|
|
Petach Tikva 49517,
|
|
Israel.
|
|
Email: mbdodge@ieee.org
|
|
Phone: +972 3 926 8421
|
|
"
|
|
DESCRIPTION
|
|
"The VDSL-LINE-MIB found in RFC 3728 defines objects for
|
|
the management of a pair of VDSL transceivers at each end of
|
|
the VDSL line. The VDSL-LINE-MIB configures and monitors the
|
|
line code independent parameters (TC layer) of the VDSL line.
|
|
This MIB module is an optional extension of the VDSL-LINE-MIB
|
|
and defines objects for configuration and monitoring of the
|
|
line code specific (LCS) elements (PMD layer) for VDSL lines
|
|
using MCM coding. The objects in this extension MIB MUST NOT
|
|
be used for VDSL lines using Single Carrier Modulation (SCM)
|
|
line coding. If an object in this extension MIB is referenced
|
|
by a line which does not use MCM, it has no effect on the
|
|
operation of that line.
|
|
|
|
Naming Conventions:
|
|
Vtuc -- (VTUC) transceiver at near (Central) end of line
|
|
Vtur -- (VTUR) transceiver at Remote end of line
|
|
Vtu -- One of either Vtuc or Vtur
|
|
Curr -- Current
|
|
LCS -- Line Code Specific
|
|
Max -- Maximum
|
|
PSD -- Power Spectral Density
|
|
Rx -- Receive
|
|
Tx -- Transmit
|
|
|
|
Copyright (C) The Internet Society (2005). This version
|
|
of this MIB module is part of RFC 4070: see the RFC
|
|
itself for full legal notices."
|
|
REVISION "200504280000Z" -- April 28, 2005
|
|
DESCRIPTION "Initial version, published as RFC 4070."
|
|
::= { transmission 229 }
|
|
|
|
vdslLineExtMCMMib OBJECT IDENTIFIER ::= { vdslExtMCMMIB 1 }
|
|
vdslLineExtMCMMibObjects OBJECT IDENTIFIER ::= {vdslLineExtMCMMib 1}
|
|
|
|
--
|
|
-- Multiple carrier modulation (MCM) configuration profile tables
|
|
--
|
|
|
|
vdslLineMCMConfProfileTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF VdslLineMCMConfProfileEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains additional information on multiple
|
|
carrier VDSL lines. One entry in this table reflects a
|
|
profile defined by a manager which can be used to
|
|
configure the VDSL line.
|
|
|
|
If an entry in this table is referenced by a line which
|
|
does not use MCM, it has no effect on the operation of that
|
|
line.
|
|
|
|
All read-create-objects defined in this table SHOULD be
|
|
stored persistently."
|
|
::= { vdslLineExtMCMMibObjects 1 }
|
|
|
|
vdslLineMCMConfProfileEntry OBJECT-TYPE
|
|
SYNTAX VdslLineMCMConfProfileEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry consists of a list of parameters that
|
|
represents the configuration of a multiple carrier
|
|
modulation VDSL modem."
|
|
INDEX { vdslLineConfProfileName }
|
|
::= { vdslLineMCMConfProfileTable 1 }
|
|
|
|
VdslLineMCMConfProfileEntry ::=
|
|
SEQUENCE
|
|
{
|
|
vdslLineMCMConfProfileTxWindowLength Unsigned32,
|
|
vdslLineMCMConfProfileRowStatus RowStatus
|
|
}
|
|
|
|
vdslLineMCMConfProfileTxWindowLength OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..255)
|
|
UNITS "samples"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Specifies the length of the transmit window, counted
|
|
in samples at the sampling rate corresponding to the
|
|
negotiated value of N."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileEntry 1 }
|
|
|
|
vdslLineMCMConfProfileRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create a new row or modify or
|
|
delete an existing row in this table.
|
|
|
|
A profile is activated by setting this object to `active'.
|
|
When `active' is set, the system will validate the profile.
|
|
|
|
None of the columns in this row may be modified while the
|
|
row is in the 'active' state.
|
|
|
|
Before a profile can be deleted or taken out of
|
|
service, (by setting this object to `destroy' or
|
|
`notInService') it must first be unreferenced
|
|
from all associated lines."
|
|
::= { vdslLineMCMConfProfileEntry 2 }
|
|
|
|
vdslLineMCMConfProfileTxBandTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF VdslLineMCMConfProfileTxBandEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains transmit band descriptor configuration
|
|
information for a VDSL line. Each entry in this table
|
|
reflects the configuration for one of possibly many bands
|
|
with a multiple carrier modulation (MCM) VDSL line.
|
|
These entries are defined by a manager and can be used to
|
|
configure the VDSL line.
|
|
|
|
If an entry in this table is referenced by a line which
|
|
does not use MCM, it has no effect on the operation of that
|
|
line.
|
|
|
|
All read-create-objects defined in this table SHOULD be
|
|
stored persistently."
|
|
::= { vdslLineExtMCMMibObjects 2 }
|
|
|
|
vdslLineMCMConfProfileTxBandEntry OBJECT-TYPE
|
|
SYNTAX VdslLineMCMConfProfileTxBandEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry consists of a transmit band descriptor, which
|
|
is defined by a start and a stop tone index."
|
|
INDEX { vdslLineConfProfileName,
|
|
vdslLineMCMConfProfileTxBandNumber }
|
|
::= { vdslLineMCMConfProfileTxBandTable 1 }
|
|
|
|
VdslLineMCMConfProfileTxBandEntry ::=
|
|
SEQUENCE
|
|
{
|
|
vdslLineMCMConfProfileTxBandNumber Unsigned32,
|
|
vdslLineMCMConfProfileTxBandStart Unsigned32,
|
|
vdslLineMCMConfProfileTxBandStop Unsigned32,
|
|
vdslLineMCMConfProfileTxBandRowStatus RowStatus
|
|
}
|
|
|
|
vdslLineMCMConfProfileTxBandNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The index for this band descriptor entry."
|
|
::= { vdslLineMCMConfProfileTxBandEntry 1 }
|
|
|
|
vdslLineMCMConfProfileTxBandStart OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Start tone index for this band."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileTxBandEntry 2 }
|
|
|
|
vdslLineMCMConfProfileTxBandStop OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Stop tone index for this band."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileTxBandEntry 3 }
|
|
|
|
vdslLineMCMConfProfileTxBandRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create a new row or modify or
|
|
delete an existing row in this table.
|
|
A profile is activated by setting this object to `active'.
|
|
When `active' is set, the system will validate the profile.
|
|
|
|
Each entry must be internally consistent, the Stop Tone must
|
|
be greater than the Start Tone. Each entry must also be
|
|
externally consistent, all entries indexed by a specific
|
|
profile must not overlap. Validation of the profile will
|
|
check both internal and external consistency.
|
|
|
|
None of the columns in this row may be modified while the
|
|
row is in the 'active' state.
|
|
|
|
Before a profile can be deleted or taken out of
|
|
service, (by setting this object to `destroy' or
|
|
`notInService') it must be first unreferenced
|
|
from all associated lines."
|
|
::= { vdslLineMCMConfProfileTxBandEntry 4 }
|
|
|
|
vdslLineMCMConfProfileRxBandTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF VdslLineMCMConfProfileRxBandEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains receive band descriptor configuration
|
|
information for a VDSL line. Each entry in this table
|
|
reflects the configuration for one of possibly many bands
|
|
with a multiple carrier modulation (MCM) VDSL line.
|
|
These entries are defined by a manager and can be used to
|
|
configure the VDSL line.
|
|
|
|
If an entry in this table is referenced by a line which
|
|
does not use MCM, it has no effect on the operation of that
|
|
line.
|
|
|
|
All read-create-objects defined in this table SHOULD be
|
|
stored persistently."
|
|
::= { vdslLineExtMCMMibObjects 3 }
|
|
|
|
vdslLineMCMConfProfileRxBandEntry OBJECT-TYPE
|
|
SYNTAX VdslLineMCMConfProfileRxBandEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry consists of a transmit band descriptor, which
|
|
is defined by a start and a stop tone index."
|
|
INDEX { vdslLineConfProfileName,
|
|
vdslLineMCMConfProfileRxBandNumber }
|
|
::= { vdslLineMCMConfProfileRxBandTable 1 }
|
|
|
|
VdslLineMCMConfProfileRxBandEntry ::=
|
|
|
|
SEQUENCE
|
|
{
|
|
vdslLineMCMConfProfileRxBandNumber Unsigned32,
|
|
vdslLineMCMConfProfileRxBandStart Unsigned32,
|
|
vdslLineMCMConfProfileRxBandStop Unsigned32,
|
|
vdslLineMCMConfProfileRxBandRowStatus RowStatus
|
|
}
|
|
|
|
vdslLineMCMConfProfileRxBandNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The index for this band descriptor entry."
|
|
::= { vdslLineMCMConfProfileRxBandEntry 1 }
|
|
|
|
vdslLineMCMConfProfileRxBandStart OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Start tone index for this band."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileRxBandEntry 2 }
|
|
|
|
vdslLineMCMConfProfileRxBandStop OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Stop tone index for this band."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileRxBandEntry 3 }
|
|
|
|
vdslLineMCMConfProfileRxBandRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create a new row or modify or
|
|
delete an existing row in this table.
|
|
|
|
A profile is activated by setting this object to `active'.
|
|
When `active' is set, the system will validate the profile.
|
|
Each entry must be internally consistent, the Stop Tone must
|
|
be greater than the Start Tone. Each entry must also be
|
|
externally consistent, all entries indexed by a specific
|
|
|
|
profile must not overlap. Validation of the profile will
|
|
check both internal and external consistency.
|
|
|
|
None of the columns in this row may be modified while the
|
|
row is in the 'active' state.
|
|
|
|
Before a profile can be deleted or taken out of
|
|
service, (by setting this object to `destroy' or
|
|
`notInService') it must be first unreferenced
|
|
from all associated lines."
|
|
::= { vdslLineMCMConfProfileRxBandEntry 4 }
|
|
|
|
vdslLineMCMConfProfileTxPSDTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains transmit PSD mask descriptor
|
|
configuration information for a VDSL line. Each entry in
|
|
this table reflects the configuration for one tone within
|
|
a multiple carrier modulation (MCM) VDSL line. These
|
|
entries are defined by a manager and can be used to
|
|
configure the VDSL line.
|
|
|
|
If an entry in this table is referenced by a line which
|
|
does not use MCM, it has no effect on the operation of that
|
|
line.
|
|
|
|
All read-create-objects defined in this table SHOULD be
|
|
stored persistently."
|
|
::= { vdslLineExtMCMMibObjects 4 }
|
|
|
|
vdslLineMCMConfProfileTxPSDEntry OBJECT-TYPE
|
|
SYNTAX VdslLineMCMConfProfileTxPSDEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry consists of a transmit PSD mask descriptor,
|
|
which defines the power spectral density (PSD) for a tone."
|
|
INDEX { vdslLineConfProfileName,
|
|
vdslLineMCMConfProfileTxPSDNumber }
|
|
::= { vdslLineMCMConfProfileTxPSDTable 1 }
|
|
|
|
VdslLineMCMConfProfileTxPSDEntry ::=
|
|
SEQUENCE
|
|
{
|
|
vdslLineMCMConfProfileTxPSDNumber Unsigned32,
|
|
vdslLineMCMConfProfileTxPSDTone Unsigned32,
|
|
vdslLineMCMConfProfileTxPSDPSD Unsigned32,
|
|
vdslLineMCMConfProfileTxPSDRowStatus RowStatus
|
|
}
|
|
|
|
vdslLineMCMConfProfileTxPSDNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The index for this mask descriptor entry."
|
|
::= { vdslLineMCMConfProfileTxPSDEntry 1 }
|
|
|
|
vdslLineMCMConfProfileTxPSDTone OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The tone index for which the PSD is being specified."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileTxPSDEntry 2 }
|
|
|
|
vdslLineMCMConfProfileTxPSDPSD OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "0.5dBm/Hz"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Power Spectral Density level in steps of 0.5dBm/Hz with
|
|
an offset of -140dBm/Hz."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileTxPSDEntry 3 }
|
|
|
|
vdslLineMCMConfProfileTxPSDRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create a new row or modify or
|
|
delete an existing row in this table.
|
|
|
|
A profile is activated by setting this object to `active'.
|
|
When `active' is set, the system will validate the profile.
|
|
|
|
None of the columns in this row may be modified while the
|
|
row is in the 'active' state.
|
|
|
|
Before a profile can be deleted or taken out of
|
|
|
|
service, (by setting this object to `destroy' or
|
|
`notInService') it must be first unreferenced
|
|
from all associated lines."
|
|
::= { vdslLineMCMConfProfileTxPSDEntry 4 }
|
|
|
|
vdslLineMCMConfProfileMaxTxPSDTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF VdslLineMCMConfProfileMaxTxPSDEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains transmit maximum PSD mask descriptor
|
|
configuration information for a VDSL line. Each entry in
|
|
this table reflects the configuration for one tone within
|
|
a multiple carrier modulation (MCM) VDSL modem. These
|
|
entries are defined by a manager and can be used to
|
|
configure the VDSL line.
|
|
|
|
If an entry in this table is referenced by a line which
|
|
does not use MCM, it has no effect on the operation of that
|
|
line.
|
|
|
|
All read-create-objects defined in this table SHOULD be
|
|
stored persistently."
|
|
::= { vdslLineExtMCMMibObjects 5 }
|
|
|
|
vdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE
|
|
SYNTAX VdslLineMCMConfProfileMaxTxPSDEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry consists of a transmit PSD mask descriptor,
|
|
which defines the maximum power spectral density (PSD)
|
|
for a tone."
|
|
INDEX { vdslLineConfProfileName,
|
|
vdslLineMCMConfProfileMaxTxPSDNumber }
|
|
::= { vdslLineMCMConfProfileMaxTxPSDTable 1 }
|
|
|
|
VdslLineMCMConfProfileMaxTxPSDEntry ::=
|
|
SEQUENCE
|
|
{
|
|
vdslLineMCMConfProfileMaxTxPSDNumber Unsigned32,
|
|
vdslLineMCMConfProfileMaxTxPSDTone Unsigned32,
|
|
vdslLineMCMConfProfileMaxTxPSDPSD Unsigned32,
|
|
vdslLineMCMConfProfileMaxTxPSDRowStatus RowStatus
|
|
}
|
|
|
|
vdslLineMCMConfProfileMaxTxPSDNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The index for this band descriptor entry."
|
|
::= { vdslLineMCMConfProfileMaxTxPSDEntry 1 }
|
|
|
|
vdslLineMCMConfProfileMaxTxPSDTone OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The tone index for which the PSD is being specified.
|
|
There must not be multiple rows defined, for a particular
|
|
profile, with the same value for this field."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileMaxTxPSDEntry 2 }
|
|
|
|
vdslLineMCMConfProfileMaxTxPSDPSD OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "0.5dBm/Hz"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Power Spectral Density level in steps of 0.5dBm/Hz with
|
|
an offset of -140dBm/Hz."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileMaxTxPSDEntry 3 }
|
|
|
|
vdslLineMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create a new row or modify or
|
|
delete an existing row in this table.
|
|
A profile is activated by setting this object to `active'.
|
|
When `active' is set, the system will validate the profile.
|
|
There must be only one entry in this table for each tone
|
|
associated with a specific profile. This will be checked
|
|
during the validation process.
|
|
|
|
None of the columns in this row may be modified while the
|
|
row is in the 'active' state.
|
|
|
|
Before a profile can be deleted or taken out of
|
|
service, (by setting this object to `destroy' or
|
|
`notInService') it must be first unreferenced
|
|
from all associated lines."
|
|
::= { vdslLineMCMConfProfileMaxTxPSDEntry 4 }
|
|
|
|
vdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains maximum receive PSD mask descriptor
|
|
configuration information for a VDSL line. Each entry in
|
|
this table reflects the configuration for one tone within
|
|
a multiple carrier modulation (MCM) VDSL modem. These
|
|
entries are defined by a manager and can be used to
|
|
configure the VDSL line.
|
|
|
|
If an entry in this table is referenced by a line which
|
|
does not use MCM, it has no effect on the operation of that
|
|
line.
|
|
|
|
All read-create-objects defined in this table SHOULD be
|
|
stored persistently."
|
|
::= { vdslLineExtMCMMibObjects 6 }
|
|
|
|
vdslLineMCMConfProfileMaxRxPSDEntry OBJECT-TYPE
|
|
SYNTAX VdslLineMCMConfProfileMaxRxPSDEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry consists of a transmit PSD mask descriptor,
|
|
which defines the power spectral density (PSD) for a
|
|
tone."
|
|
INDEX { vdslLineConfProfileName,
|
|
vdslLineMCMConfProfileMaxRxPSDNumber }
|
|
::= { vdslLineMCMConfProfileMaxRxPSDTable 1 }
|
|
|
|
VdslLineMCMConfProfileMaxRxPSDEntry ::=
|
|
SEQUENCE
|
|
{
|
|
vdslLineMCMConfProfileMaxRxPSDNumber Unsigned32,
|
|
vdslLineMCMConfProfileMaxRxPSDTone Unsigned32,
|
|
vdslLineMCMConfProfileMaxRxPSDPSD Unsigned32,
|
|
vdslLineMCMConfProfileMaxRxPSDRowStatus RowStatus
|
|
}
|
|
|
|
vdslLineMCMConfProfileMaxRxPSDNumber OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The index for this band descriptor entry."
|
|
::= { vdslLineMCMConfProfileMaxRxPSDEntry 1 }
|
|
|
|
vdslLineMCMConfProfileMaxRxPSDTone OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4096)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The tone index for which the PSD is being specified.
|
|
There must not be multiple rows defined, for a particular
|
|
profile, with the same value for this field."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileMaxRxPSDEntry 2 }
|
|
|
|
vdslLineMCMConfProfileMaxRxPSDPSD OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "0.5dBm/Hz"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Power Spectral Density level in steps of 0.5dBm/Hz with
|
|
an offset of -140dBm/Hz."
|
|
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
|
|
::= { vdslLineMCMConfProfileMaxRxPSDEntry 3 }
|
|
|
|
vdslLineMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to create a new row or modify or
|
|
delete an existing row in this table.
|
|
|
|
A profile is activated by setting this object to `active'.
|
|
When `active' is set, the system will validate the profile.
|
|
There must be only one entry in this table for each tone
|
|
associated with a specific profile. This will be checked
|
|
during the validation process.
|
|
|
|
None of the columns in this row may be modified while the
|
|
row is in the 'active' state.
|
|
|
|
Before a profile can be deleted or taken out of
|
|
service, (by setting this object to `destroy' or
|
|
`notInService') it must be first unreferenced
|
|
from all associated lines."
|
|
::= { vdslLineMCMConfProfileMaxRxPSDEntry 4 }
|
|
|
|
-- conformance information
|
|
|
|
vdslLineExtMCMConformance OBJECT IDENTIFIER ::=
|
|
{ vdslLineExtMCMMib 2 }
|
|
vdslLineExtMCMGroups OBJECT IDENTIFIER ::=
|
|
{ vdslLineExtMCMConformance 1 }
|
|
vdslLineExtMCMCompliances OBJECT IDENTIFIER ::=
|
|
{ vdslLineExtMCMConformance 2 }
|
|
|
|
vdslLineExtMCMMibCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for SNMP entities which
|
|
manage VDSL interfaces."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS
|
|
{
|
|
vdslLineExtMCMGroup
|
|
}
|
|
::= { vdslLineExtMCMCompliances 1 }
|
|
|
|
-- units of conformance
|
|
|
|
vdslLineExtMCMGroup OBJECT-GROUP
|
|
OBJECTS
|
|
{
|
|
vdslLineMCMConfProfileTxWindowLength,
|
|
vdslLineMCMConfProfileRowStatus,
|
|
vdslLineMCMConfProfileTxBandStart,
|
|
vdslLineMCMConfProfileTxBandStop,
|
|
vdslLineMCMConfProfileTxBandRowStatus,
|
|
vdslLineMCMConfProfileRxBandStart,
|
|
vdslLineMCMConfProfileRxBandStop,
|
|
vdslLineMCMConfProfileRxBandRowStatus,
|
|
vdslLineMCMConfProfileTxPSDTone,
|
|
vdslLineMCMConfProfileTxPSDPSD,
|
|
vdslLineMCMConfProfileTxPSDRowStatus,
|
|
vdslLineMCMConfProfileMaxTxPSDTone,
|
|
vdslLineMCMConfProfileMaxTxPSDPSD,
|
|
vdslLineMCMConfProfileMaxTxPSDRowStatus,
|
|
vdslLineMCMConfProfileMaxRxPSDTone,
|
|
vdslLineMCMConfProfileMaxRxPSDPSD,
|
|
vdslLineMCMConfProfileMaxRxPSDRowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration
|
|
|
|
information for a VDSL line based upon multiple
|
|
carrier modulation modem."
|
|
::= { vdslLineExtMCMGroups 1 }
|
|
|
|
END
|