WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/cisco/CISCO-OPTICAL-MIB

2545 lines
96 KiB
Plaintext
Raw Blame History

-- *****************************************************************
-- CISCO-OPTICAL-MIB.my
-- OPTICAL INTERFACE MIB
--
-- June 2015 Aditi Gupta (aditigu)
--
-- Copyright (c) 2015 by Cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************
CISCO-OPTICAL-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Integer32,
Unsigned32
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
TruthValue,
DisplayString,
MacAddress,
TimeStamp
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
ifIndex,
ifName
FROM IF-MIB
ciscoMgmt
FROM CISCO-SMI;
ciscoOpticalMIB MODULE-IDENTITY
LAST-UPDATED "201605240000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-<list>@cisco.com"
DESCRIPTION
"This MIB module defines the managed objects for physical layer
characteristics of optical interfaces and performance
statistics objects for protocol specific counters in optical
devices.
Performance monitoring (PM) parameters are used by service
providers to gather, store, set thresholds for and report
performance data for early detection of problems.
Thresholds are used to set error levels for each PM parameter.
During the accumulation cycle, if the current value of a
performance monitoring parameter reaches or exceeds its
corresponding threshold value, a threshold crossing alarm (TCA)
is generated. The TCAs provide early detection of performance
degradation.
Glossary:
LBC : Laser Bias Current
TX : Transmit
RX : Receive
PMD : Polarization Mode Dispersion
OSNR : Optical Signal to Noise Ratio
DGD : Differential Group Delay
CD : Chromatic Dispersion
rad/s : radian per second
dB : decibel
dBm : decibel-milliwatt
ps : picosecond
nm : nanometer."
REVISION "201605240000Z"
DESCRIPTION
"Added
1. Extend CoiIntervalType to include thirtySecond.
2. Extend coiOpticalControllerEntry to include
coiOpticalControllerTotalRXPower,
coiOpticalControllerTotalTXPower.
3. Add coiOpticalPowerGroup.
4. Deprecated the ciscoOpticalMIBCompliance compliance,
added ciscoOpticalMIBComplianceRev1."
REVISION "201512010000Z"
DESCRIPTION
"Added
1. NOTIFICATION-TYPE coiOpticalEquipmentAlarm
2. Textual Convention CoiOptAlarmType, CoiOptAlarmStatus,
CoiOptAlarmSeverity, CoiOptAlarmServiceAffecting.
3. coiOpticalEquipmentAlarmGroup OBJECT INDENTIFIER, with
coiOpticalAlarmLocation, coiOpticalAlarmType,
coiOpticalAlarmTimeStamp, coiOpticalAlarmName,
coiOpticalAlarmAdditionalInfo, coiOpticalAlarmSeverity,
coiOpticalAlarmStatus, coiOpticalAlarmServiceAffecting as
OBJECT-TYPE.
4. ppmFail bit for coiOpticalControllerStatus."
REVISION "201510300000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 828 }
CoiOpticalPower ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value indicates the optical receive or transmit power."
SYNTAX Integer32 (-4000..3000)
CoiOpticalWavelength ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value represents the wavelength of optical signals, in an
optical interface. It is represented in units of nanometers.
A value of zero either indicates that the wavelength is
unknown, or that it does not fall under the frequency grid
defined in ITU-T G.694.1"
REFERENCE
"ITU - T Recommendation G.694.1 - Spectral grids for WDM
applications: DWDM frequency grid, May 2002"
SYNTAX Unsigned32 (0 | 1528770..1604030)
CoiIntervalType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value indicates the time period over which performance
monitoring data has been collected. Valid values are -
fifteenMin(1) - values for the 15 min interval.
oneDay(2) - values for the 1 Day interval.
thirtySecond(3)- values for the 30 Sec interval."
SYNTAX INTEGER {
fifteenMin(1),
oneDay(2),
thirtySecond(3)
}
CoiPortType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value indicates the port type of the optical
interface. Valid values are -
clientPort(1) - denotes client port.
trunkPort(2) - denotes trunk port."
SYNTAX INTEGER {
clientPort(1),
trunkPort(2)
}
CoiOptAlarmType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value indicates the alarm type.
alarmUnknown(1) - denotes unknown alarm type.
equipmentFailure(2) - denotes equipment fail alarm type."
SYNTAX INTEGER {
alarmUnknown(1),
equipmentFailure(2)
}
CoiOptAlarmSeverity ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This will indicate the severity of the notification being
sent out. Valid values are -
notReported(1) - alarm not reported.
notAlarmed(2) - alarm not raised.
minor(3) - minor alarm.
major(4) - major alarm.
critical(5) - critical alarm."
SYNTAX INTEGER {
notReported(1),
notAlarmed(2),
minor(3),
major(4),
critical(5)
}
CoiOptAlarmStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This will indicate the status of the alarm.
Valid values are -
raised(1) - alarm in raised state.
cleared(2) - alarm in cleared state.
transient(3)- alarm in transient state."
SYNTAX INTEGER {
raised(1),
cleared(2),
transient(3)
}
CoiOptAlarmServiceAffecting ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This will indicate the sevice-affecting state of the alarm.
Valid values are -
Service affecting(1) - alarm affects service.
Non-Service affecting(2)- alarm does not affect service."
SYNTAX INTEGER {
serviceAffecting(1),
nonServiceAffecting(2)
}
-- Textual Conventions definition will be defined before this line
ciscoOpticalMIBNotifs OBJECT IDENTIFIER
::= { ciscoOpticalMIB 0 }
ciscoOpticalMIBObjects OBJECT IDENTIFIER
::= { ciscoOpticalMIB 1 }
coiOpticsStatusChange NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ifName,
coiOpticalControllerPortType,
coiOpticalControllerStatus
}
STATUS current
DESCRIPTION
"This notification is generated whenever the defect status of
Optics on an interface changes.
Varbind 'ifIndex' indicates the interface whose defect status
of the Optics layer has just changed.
Varbind 'ifName' indicates the interface Name whose defect
status of the Optics layer has just changed.
Varbind 'coiOpticalControllerPortType' indicates the port type
of the interface whose defect status of the Optics layer has
just changed.
Varbind 'coiOpticalControllerStatus' indicates the current
defect status of the Optics layer on the interface."
::= { ciscoOpticalMIBNotifs 1 }
coiOpticalEquipmentAlarm NOTIFICATION-TYPE
OBJECTS {
coiOpticalAlarmLocation,
coiOpticalAlarmType,
coiOpticalAlarmTimeStamp,
coiOpticalAlarmName,
coiOpticalAlarmAdditionalInfo,
coiOpticalAlarmSeverity,
coiOpticalAlarmStatus,
coiOpticalAlarmServiceAffecting
}
STATUS current
DESCRIPTION
"This notification is generated whenever the optical equipment
alarm is generated.
Varbind 'coiOpticalAlarmLocation' indicates the location on
which equipment failed alarm has generated.
Varbind 'coiOpticalAlarmType' indicates the type of alarm.
Varbind 'coiOpticalAlarmTimeStamp' indicates the timestamp when
alarm is generated.
Varbind 'coiOpticalAlarmName' indicates the alarm object.
Varbind 'coiOpticalAlarmAdditionalInfo' indicates additional
info related to the alarm.
Varbind 'coiOpticalAlarmSeverity' indicates the severity of the
alarm.
Varbind 'coiOpticalAlarmStatus' indicates status of the alarm.
Varbind 'coiOpticalAlarmServiceAffecting' indicates the service
affected state when alarm is generated."
::= { ciscoOpticalMIBNotifs 2 }
coiOpticalController OBJECT IDENTIFIER
::= { ciscoOpticalMIBObjects 1 }
coiOpticalPerformanceMonitoring OBJECT IDENTIFIER
::= { ciscoOpticalMIBObjects 2 }
coiOpticalNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls the generation of coiOpticsStatusChange
notification.
If the value of this object is 'true', then the generation of
coiOpticsStatusChange notification is enabled. If the value of
this object is 'false', then the generation of
coiOpticsStatusChange notification is disabled."
::= { coiOpticalController 1 }
coiOpticalControllerTable OBJECT-TYPE
SYNTAX SEQUENCE OF CoiOpticalControllerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides management information for optical layer
related attributes of interfaces with an ifType of
opticalChannel(195)."
::= { coiOpticalController 2 }
coiOpticalControllerEntry OBJECT-TYPE
SYNTAX CoiOpticalControllerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing management information on optical layer
related attributes of interfaces with an ifType
opticalChannel(195). Entries are created by the feature when a
new interface is added to the ifTable."
INDEX { ifIndex }
::= { coiOpticalControllerTable 1 }
CoiOpticalControllerEntry ::= SEQUENCE {
coiOpticalControllerWavelength CoiOpticalWavelength,
coiOpticalControllerLaserStatus INTEGER,
coiOpticalControllerFrequency Unsigned32,
coiOpticalControllerChannelNumber Unsigned32,
coiOpticalControllerTransmitPower CoiOpticalPower,
coiOpticalControllerOpticsType DisplayString,
coiOpticalControllerRXLowThreshold CoiOpticalPower,
coiOpticalControllerTXLowThreshold CoiOpticalPower,
coiOpticalControllerRXHighThreshold CoiOpticalPower,
coiOpticalControllerTXHighThreshold CoiOpticalPower,
coiOpticalControllerLBCHighThreshold Integer32,
coiOpticalControllerStatus BITS,
coiOpticalControllerPortType CoiPortType,
coiOpticalControllerTotalRXPower CoiOpticalPower,
coiOpticalControllerTotalTXPower CoiOpticalPower
}
coiOpticalControllerWavelength OBJECT-TYPE
SYNTAX CoiOpticalWavelength
UNITS "1/100 nm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the wavelength on
optical channel interfaces in 1/100 nm."
DEFVAL { 1529553 }
::= { coiOpticalControllerEntry 1 }
coiOpticalControllerLaserStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the current operational state of the Laser.
Valid values are -
'up' - The laser is operational.
'down' - The laser is not operational."
::= { coiOpticalControllerEntry 2 }
coiOpticalControllerFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "100 MHz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the frequency on optical
channel interfaces in 100 MHz."
::= { coiOpticalControllerEntry 3 }
coiOpticalControllerChannelNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the channel number on
optical channel interfaces. Channel Number is set to 0 if not
50GHz grid."
::= { coiOpticalControllerEntry 4 }
coiOpticalControllerTransmitPower OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the Transmit Power in
1/100 dBm on optical channel interfaces."
::= { coiOpticalControllerEntry 5 }
coiOpticalControllerOpticsType OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the description of optics present on optical
channel interfaces."
::= { coiOpticalControllerEntry 6 }
coiOpticalControllerRXLowThreshold OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the Receive Low Threshold in
1/100 dBm on optical channel interfaces."
::= { coiOpticalControllerEntry 7 }
coiOpticalControllerTXLowThreshold OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the Transmit Low Threshold in
1/100 dBm on optical channel interfaces."
::= { coiOpticalControllerEntry 8 }
coiOpticalControllerRXHighThreshold OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the Receive High Threshold in
1/100 dBm on optical channel interfaces."
::= { coiOpticalControllerEntry 9 }
coiOpticalControllerTXHighThreshold OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the Transmit High Threshold
in 1/100 dBm on optical channel interfaces."
::= { coiOpticalControllerEntry 10 }
coiOpticalControllerLBCHighThreshold OBJECT-TYPE
SYNTAX Integer32 (0..1000)
UNITS "1/10 %"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the Laser Bias Current High
Threshold in 1/10% on optical channel interfaces."
::= { coiOpticalControllerEntry 11 }
coiOpticalControllerStatus OBJECT-TYPE
SYNTAX BITS {
noDefect(0),
improprmvl(1),
mea(2),
provMismatch(3),
highRXPwr(4),
highTXPwr(5),
lowRXPwr(6),
lowTXPwr(7),
highLBC(8),
highDGD(9),
outOfRangeCD(10),
lowOSNR(11),
wvlOutOfLock(12),
highLaserTemp(13),
lowLaserTemp(14),
ppmFail(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current defect status of the Optics
layer.
noDefect(0): No Defect. This bit is set high when no
defect is detected on the optics.
improprmvl(1): Improper Removal. This will be set when
a physical pluggable is absent on a service
(hw-module) provisioned port.
mea(2): This bit will be set when Port Pluggable
Module Mismatches With Pre-Provisoned PPM.
provMismatch(3): Provision Mismatch. This bit is set when
Provisioned wavelength is Not supported By
Pluggable.
highRXPwr(4): High Receive Power. This bit is set when the
measured optical power of the received
signal exceeds the threshold high value,
which is user-provisionable.
highTXPwr(5): High Transmit Power. This bit is set when
Pluggable measured optical power of the
transmitted signal falls over the threshold.
lowRXPwr(6): Low Receive Power. This bit is set when the
measured optical power of the received
signal falls below the low threshold value,
which is user-provisionable.
lowTXPwr(7): Low Transmit Power. This bit is set when
Pluggable measured optical power of the
transmitted signal falls below the low
threshold.
highLBC(8): High Laser Bias. This bit is set when the
Physical Pluggable Port laser reads laser
bias value beyond configured high threshold.
highDGD(9): High DGD. This bit is set when the pluggable
port Module reads the Differential Group
delay value that exceeds the configured high
threshold.
outOfRangeCD(10): Out of Range Chromatic Dispersion. This bit
is set when the Chromatic dispersion value
read by the associated HW is out of range
with the configured threshold.
lowOSNR(11): Low Optical Signal to Noise Ratio. This bit
is set when the HW read Optical Signal to
Noise ratio falls below the configured low
threshold.
wvlOutOfLock(12): Wavelength Out of Lock. This bit is set when
Trunk Port optics detects that optical input
frequency is out of range.
highLaserTemp(13): High LaserTemp.This bit is set when the
internally measured transceiver temperature
exceeds the card setting by 35.6 degrees F
or 2 degrees C. A laser temperature change
affects the transmitted wavelength.
lowLaserTemp(14): Low LaserTemp. This bit is set when the
internally measured transceiver temperature
falls below the card setting by 35.6 degrees
F or 2 degrees C. A laser temperature change
affects the transmitted wavelength. (This
temperature is equivalent to about 200
picometers of wavelength.
ppmFail(15): Pluggable Equipment Fail. This bit is set
when Pluggable Equipment is not operational
or manageable.
This object is sent out as a notification to the agent."
::= { coiOpticalControllerEntry 12 }
coiOpticalControllerPortType OBJECT-TYPE
SYNTAX CoiPortType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the port type of the optical interface."
::= { coiOpticalControllerEntry 13 }
coiOpticalControllerTotalRXPower OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the total receive power in
1/100 dBm on optical channel interfaces."
::= { coiOpticalControllerEntry 14 }
coiOpticalControllerTotalTXPower OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the total transmit power
in 1/100 dBm on optical channel interfaces."
::= { coiOpticalControllerEntry 15 }
coiOpticalControllerPerLaneTable OBJECT-TYPE
SYNTAX SEQUENCE OF CoiOpticalControllerPerLaneEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the management information for optical
layer related attributes of interfaces with an ifType of
opticalChannel(195) and lane number as
coiOpticalControllerLane."
::= { coiOpticalController 3 }
coiOpticalControllerPerLaneEntry OBJECT-TYPE
SYNTAX CoiOpticalControllerPerLaneEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing management information on optical layer
related attributes of interfaces with an ifType
opticalChannel(195) and lane number as
coiOpticalControllerLane. Entries are created by the feature
when a new interface is added to the ifTable."
INDEX {
ifIndex,
coiOpticalControllerLane
}
::= { coiOpticalControllerPerLaneTable 1 }
CoiOpticalControllerPerLaneEntry ::= SEQUENCE {
coiOpticalControllerLane Integer32,
coiOpticalControllerPerLaneRXPower CoiOpticalPower,
coiOpticalControllerPerLaneTXPower CoiOpticalPower,
coiOpticalControllerPerLaneLBC Integer32,
coiOpticalControllerPerLaneOSNR Integer32,
coiOpticalControllerPerLaneChromaticDispersion Integer32,
coiOpticalControllerPerLaneDifferentialGroupDelay Integer32,
coiOpticalControllerPerLaneSecondOrderPMD Integer32,
coiOpticalControllerPerLanePolarizationDependentLoss Integer32,
coiOpticalControllerPerLanePolarizationChangeRate Integer32,
coiOpticalControllerPerLanePhaseNoise Integer32
}
coiOpticalControllerLane OBJECT-TYPE
SYNTAX Integer32 (1..12)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the lane number for the optical
controller. Each optical controller is divided into data lanes,
with each lane operating at some data rate, giving an aggregated
bandwidth of the controller, as a whole. Lane is applicable for
breakout mode of operation."
::= { coiOpticalControllerPerLaneEntry 1 }
coiOpticalControllerPerLaneRXPower OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Receive power in 1/100 dBm."
::= { coiOpticalControllerPerLaneEntry 2 }
coiOpticalControllerPerLaneTXPower OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Transmit power in 1/100 dBm."
::= { coiOpticalControllerPerLaneEntry 3 }
coiOpticalControllerPerLaneLBC OBJECT-TYPE
SYNTAX Integer32 (0..1000)
UNITS "1/10 %"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Laser Bias Current in 1/10%."
::= { coiOpticalControllerPerLaneEntry 4 }
coiOpticalControllerPerLaneOSNR OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Optical Signal to Noise Ratio in
1/100 dB."
::= { coiOpticalControllerPerLaneEntry 5 }
coiOpticalControllerPerLaneChromaticDispersion OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the measure of spread of light pulse
in ps/nm."
::= { coiOpticalControllerPerLaneEntry 6 }
coiOpticalControllerPerLaneDifferentialGroupDelay OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the propagation time difference
between eigenmodes X and Y in 1/100 ps."
::= { coiOpticalControllerPerLaneEntry 7 }
coiOpticalControllerPerLaneSecondOrderPMD OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the threshold Second Order Polarization
Mode Dispersion in 1/100 ps^2."
::= { coiOpticalControllerPerLaneEntry 8 }
coiOpticalControllerPerLanePolarizationDependentLoss OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the threshold Polarization Dependent
Loss in 1/100 dB."
::= { coiOpticalControllerPerLaneEntry 9 }
coiOpticalControllerPerLanePolarizationChangeRate OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Polarization Change Rate in
1/100 rad/s."
::= { coiOpticalControllerPerLaneEntry 10 }
coiOpticalControllerPerLanePhaseNoise OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Fluctuations in the Phase of a
Waveform in 1/1000 dB."
::= { coiOpticalControllerPerLaneEntry 11 }
coiOpticalClientInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF CoiOpticalClientInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides management information for optical's
client layer related attributes of interfaces with an ifType
of ethernetCsmacd(6).This parameter is applicable only for
client interfaces."
::= { ciscoOpticalMIBObjects 3 }
coiOpticalClientInfoEntry OBJECT-TYPE
SYNTAX CoiOpticalClientInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing information for optical's
client layer related attributes of interfaces with an ifType
of ethernetCsmacd(6). Entries are created by the feature when
the interface discovers the neighbour's ethernet MAC Address."
INDEX {
ifIndex
}
::= { coiOpticalClientInfoTable 1 }
CoiOpticalClientInfoEntry ::= SEQUENCE {
coiOpticalClientEthernetNeighbourMAC MacAddress
}
coiOpticalClientEthernetNeighbourMAC OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the neighbour MAC Address to which the
interface is connected."
::= { coiOpticalClientInfoEntry 1 }
coiOpticalThresholdTable OBJECT-TYPE
SYNTAX SEQUENCE OF CoiOpticalThresholdEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides threshold information for optical layer
related attributes of interfaces with an ifType of
opticalChannel(195) and Interval type as
coiOptThreshIntervalType."
::= { coiOpticalPerformanceMonitoring 1 }
coiOpticalThresholdEntry OBJECT-TYPE
SYNTAX CoiOpticalThresholdEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing threshold information on optical layer
related attributes of interfaces with an ifType
opticalChannel(195). Entries are created by the feature
when a new interface is added to the ifTable."
INDEX {
ifIndex,
coiOptThreshIntervalType
}
::= { coiOpticalThresholdTable 1 }
CoiOpticalThresholdEntry ::= SEQUENCE {
coiOptThreshIntervalType CoiIntervalType,
coiOptThreshTXPowerMin CoiOpticalPower,
coiOptThreshRXPowerMin CoiOpticalPower,
coiOptThreshOSNRMin Integer32,
coiOptThreshChromaticDispersionMin Integer32,
coiOptThreshDifferentialGroupDelayMin Integer32,
coiOptThreshSecondOrderPMDMin Integer32,
coiOptThreshPolarizationDependentLossMin Integer32,
coiOptThreshPolarizationChangeRateMin Integer32,
coiOptThreshPhaseNoiseMin Integer32,
coiOptThreshLBCMin Integer32,
coiOptThreshTXPowerMax CoiOpticalPower,
coiOptThreshRXPowerMax CoiOpticalPower,
coiOptThreshOSNRMax Integer32,
coiOptThreshChromaticDispersionMax Integer32,
coiOptThreshDifferentialGroupDelayMax Integer32,
coiOptThreshSecondOrderPMDMax Integer32,
coiOptThreshPolarizationDependentLossMax Integer32,
coiOptThreshPolarizationChangeRateMax Integer32,
coiOptThreshPhaseNoiseMax Integer32,
coiOptThreshLBCMax Integer32,
coiOptThreshTXPowerEnableMin TruthValue,
coiOptThreshRXPowerEnableMin TruthValue,
coiOptThreshOSNREnableMin TruthValue,
coiOptThreshChromaticDispersionEnableMin TruthValue,
coiOptThreshDifferentialGroupDelayEnableMin TruthValue,
coiOptThreshSecondOrderPMDEnableMin TruthValue,
coiOptThreshPolarizationDependentLossEnableMin TruthValue,
coiOptThreshPolarizationChangeRateEnableMin TruthValue,
coiOptThreshPhaseNoiseEnableMin TruthValue,
coiOptThreshLBCEnableMin TruthValue,
coiOptThreshTXPowerEnableMax TruthValue,
coiOptThreshRXPowerEnableMax TruthValue,
coiOptThreshOSNREnableMax TruthValue,
coiOptThreshChromaticDispersionEnableMax TruthValue,
coiOptThreshDifferentialGroupDelayEnableMax TruthValue,
coiOptThreshSecondOrderPMDEnableMax TruthValue,
coiOptThreshPolarizationDependentLossEnableMax TruthValue,
coiOptThreshPolarizationChangeRateEnableMax TruthValue,
coiOptThreshPhaseNoiseEnableMax TruthValue,
coiOptThreshLBCEnableMax TruthValue
}
coiOptThreshIntervalType OBJECT-TYPE
SYNTAX CoiIntervalType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object gives the interval type during which the
performance statistics are accumulated for the interface."
::= { coiOpticalThresholdEntry 1 }
coiOptThreshTXPowerMin OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
Transmit power for the interface in 1/100 dBm."
::= { coiOpticalThresholdEntry 2 }
coiOptThreshRXPowerMin OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
Receive power for the interface in 1/100 dBm."
::= { coiOpticalThresholdEntry 3 }
coiOptThreshOSNRMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
Optical Signal to Noise Ratio for the interface in 1/100 dB."
::= { coiOpticalThresholdEntry 4 }
coiOptThreshChromaticDispersionMin OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
measure of spread of light pulse for the interface in ps/nm."
::= { coiOpticalThresholdEntry 5 }
coiOptThreshDifferentialGroupDelayMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
propagation time difference between eigenmodes X and Y for the
interface in 1/100 ps."
::= { coiOpticalThresholdEntry 6 }
coiOptThreshSecondOrderPMDMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
Second Order Polarization Mode Dispersion for the interface in
1/100 ps^2."
::= { coiOpticalThresholdEntry 7 }
coiOptThreshPolarizationDependentLossMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
Polarization Dependent Loss for the interface in 1/100 dB."
::= { coiOpticalThresholdEntry 8 }
coiOptThreshPolarizationChangeRateMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
Polarization Change Rate for the interface in 1/100 rad/s."
::= { coiOpticalThresholdEntry 9 }
coiOptThreshPhaseNoiseMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minimum
Fluctuations in the Phase of a Waveform for the interface in
1/1000 dB."
::= { coiOpticalThresholdEntry 10 }
coiOptThreshLBCMin OBJECT-TYPE
SYNTAX Integer32 (0..1000)
UNITS "1/10 %"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of minumum
Laser Bias Current in 1/10%."
::= { coiOpticalThresholdEntry 11 }
coiOptThreshTXPowerMax OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Transmit power for the interface in 1/100 dBm."
::= { coiOpticalThresholdEntry 12 }
coiOptThreshRXPowerMax OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Receive power for the interface in 1/100 dBm."
::= { coiOpticalThresholdEntry 13 }
coiOptThreshOSNRMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Optical Signal to Noise Ratio for the interface in 1/100 dB."
::= { coiOpticalThresholdEntry 14 }
coiOptThreshChromaticDispersionMax OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
measure of spread of light pulse for the interface in ps/nm."
::= { coiOpticalThresholdEntry 15 }
coiOptThreshDifferentialGroupDelayMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
propagation time difference between eigenmodes X and Y for the
interface in 1/100 ps."
::= { coiOpticalThresholdEntry 16 }
coiOptThreshSecondOrderPMDMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Second Order Polarization Mode Dispersion for the interface in
1/100 ps^2."
::= { coiOpticalThresholdEntry 17 }
coiOptThreshPolarizationDependentLossMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Polarization Dependent Loss for the interface in 1/100 dB."
::= { coiOpticalThresholdEntry 18 }
coiOptThreshPolarizationChangeRateMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Polarization Change Rate in 1/100 rad/s for the interface."
::= { coiOpticalThresholdEntry 19 }
coiOptThreshPhaseNoiseMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Fluctuations in the Phase of a Waveform in 1/1000 dB for the
interface."
::= { coiOpticalThresholdEntry 20 }
coiOptThreshLBCMax OBJECT-TYPE
SYNTAX Integer32 (0..1000)
UNITS "1/10 %"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the threshold of maximum
Laser Bias Current in 1/10 % for the interface."
::= { coiOpticalThresholdEntry 21 }
coiOptThreshTXPowerEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of threshold
min Transmit power for the interface."
::= { coiOpticalThresholdEntry 22 }
coiOptThreshRXPowerEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min Receive power for the interface."
::= { coiOpticalThresholdEntry 23 }
coiOptThreshOSNREnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min Optical Signal to Noise Ratio for the interface."
::= { coiOpticalThresholdEntry 24 }
coiOptThreshChromaticDispersionEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min measure of spread of light pulse for the
interface."
::= { coiOpticalThresholdEntry 25 }
coiOptThreshDifferentialGroupDelayEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min propagation time difference between eigenmodes X
and Y for the interface."
::= { coiOpticalThresholdEntry 26 }
coiOptThreshSecondOrderPMDEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min Second Order Polarization Mode Dispersion for
the interface."
::= { coiOpticalThresholdEntry 27 }
coiOptThreshPolarizationDependentLossEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min Polarization Dependent Loss for the interface."
::= { coiOpticalThresholdEntry 28 }
coiOptThreshPolarizationChangeRateEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min Polarization Change Rate for the interface."
::= { coiOpticalThresholdEntry 29 }
coiOptThreshPhaseNoiseEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min Fluctuations in the Phase of a Waveform for the
interface."
::= { coiOpticalThresholdEntry 30 }
coiOptThreshLBCEnableMin OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold min Laser Bias Current for the interface."
::= { coiOpticalThresholdEntry 31 }
coiOptThreshTXPowerEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Transmit power for the interface."
::= { coiOpticalThresholdEntry 32 }
coiOptThreshRXPowerEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Receive power for the interface."
::= { coiOpticalThresholdEntry 33 }
coiOptThreshOSNREnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Optical Signal to Noise Ratio for the interface."
::= { coiOpticalThresholdEntry 34 }
coiOptThreshChromaticDispersionEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max measure of spread of light pulse for the
interface."
::= { coiOpticalThresholdEntry 35 }
coiOptThreshDifferentialGroupDelayEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max propagation time difference between eigenmodes
X and Y for the interface."
::= { coiOpticalThresholdEntry 36 }
coiOptThreshSecondOrderPMDEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Second Order Polarization Mode Dispersion for the
interface."
::= { coiOpticalThresholdEntry 37 }
coiOptThreshPolarizationDependentLossEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Polarization Dependent Loss for the interface."
::= { coiOpticalThresholdEntry 38 }
coiOptThreshPolarizationChangeRateEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Polarization Change Rate for the interface."
::= { coiOpticalThresholdEntry 39 }
coiOptThreshPhaseNoiseEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Fluctuations in the Phase of a Waveform for the
interface."
::= { coiOpticalThresholdEntry 40 }
coiOptThreshLBCEnableMax OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the enablement of the
threshold max Laser Bias Current for the interface."
::= { coiOpticalThresholdEntry 41 }
coiOpticalCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF CoiOpticalCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides current information for optical layer
related attributes of interfaces with an ifType of
opticalChannel(195), Lane as coiOptCurrentLane and Interval
as coiOptCurrentIntervalType."
::= { coiOpticalPerformanceMonitoring 2 }
coiOpticalCurrentEntry OBJECT-TYPE
SYNTAX CoiOpticalCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing current information on optical layer
related attributes of interfaces with an ifType
opticalChannel(195). Entries are created by the feature when
a new interface is added to the ifTable."
INDEX {
ifIndex,
coiOptCurrentLane,
coiOptCurrentIntervalType
}
::= { coiOpticalCurrentTable 1 }
CoiOpticalCurrentEntry ::= SEQUENCE {
coiOptCurrentLane Integer32,
coiOptCurrentIntervalType CoiIntervalType,
coiOptCurrentTXPowerMax CoiOpticalPower,
coiOptCurrentRXPowerMax CoiOpticalPower,
coiOptCurrentOSNRMax Integer32,
coiOptCurrentChromaticDispersionMax Integer32,
coiOptCurrentDifferentialGroupDelayMax Integer32,
coiOptCurrentSecondOrderPMDMax Integer32,
coiOptCurrentPolarizationDependentLossMax Integer32,
coiOptCurrentPolarizationChangeRateMax Integer32,
coiOptCurrentPhaseNoiseMax Integer32,
coiOptCurrentLBCMax Integer32,
coiOptCurrentTXPowerMin CoiOpticalPower,
coiOptCurrentRXPowerMin CoiOpticalPower,
coiOptCurrentOSNRMin Integer32,
coiOptCurrentChromaticDispersionMin Integer32,
coiOptCurrentDifferentialGroupDelayMin Integer32,
coiOptCurrentSecondOrderPMDMin Integer32,
coiOptCurrentPolarizationDependentLossMin Integer32,
coiOptCurrentPolarizationChangeRateMin Integer32,
coiOptCurrentPhaseNoiseMin Integer32,
coiOptCurrentLBCMin Integer32,
coiOptCurrentTXPowerAvg CoiOpticalPower,
coiOptCurrentRXPowerAvg CoiOpticalPower,
coiOptCurrentOSNRAvg Integer32,
coiOptCurrentChromaticDispersionAvg Integer32,
coiOptCurrentDifferentialGroupDelayAvg Integer32,
coiOptCurrentSecondOrderPMDAvg Integer32,
coiOptCurrentPolarizationDependentLossAvg Integer32,
coiOptCurrentPolarizationChangeRateAvg Integer32,
coiOptCurrentPhaseNoiseAvg Integer32,
coiOptCurrentLBCAvg Integer32,
coiOptCurrentTimestamp OCTET STRING
}
coiOptCurrentLane OBJECT-TYPE
SYNTAX Integer32 (1..12)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the lane number for the optical
interface. Each optical controller is divided into data lanes
with each lane operating at some data rate, giving an
aggregated bandwidth of the controller as a whole. Lane is
applicable for breakout mode of operation."
::= { coiOpticalCurrentEntry 1 }
coiOptCurrentIntervalType OBJECT-TYPE
SYNTAX CoiIntervalType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object gives the interval type during which the
current performance statistics are accumulated."
::= { coiOpticalCurrentEntry 2 }
coiOptCurrentTXPowerMax OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Transmit power
for the interface in 1/100 dBm."
::= { coiOpticalCurrentEntry 3 }
coiOptCurrentRXPowerMax OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Receive power for the
interface in 1/100 dBm."
::= { coiOpticalCurrentEntry 4 }
coiOptCurrentOSNRMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Optical Signal to Noise
Ratio for the interface in 1/100 dB."
::= { coiOpticalCurrentEntry 5 }
coiOptCurrentChromaticDispersionMax OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max measure of spread of
light pulse for the interface in ps/nm."
::= { coiOpticalCurrentEntry 6 }
coiOptCurrentDifferentialGroupDelayMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max propagation time
difference between eigenmodes X and Y for the interface in
1/100 ps."
::= { coiOpticalCurrentEntry 7 }
coiOptCurrentSecondOrderPMDMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Second Order
Polarization Mode Dispersion for the interface in 1/100 ps^2."
::= { coiOpticalCurrentEntry 8 }
coiOptCurrentPolarizationDependentLossMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Polarization Dependent
Loss for the interface in 1/100 dB."
::= { coiOpticalCurrentEntry 9 }
coiOptCurrentPolarizationChangeRateMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Polarization Change
Rate for the interface in 1/100 rad/s."
::= { coiOpticalCurrentEntry 10 }
coiOptCurrentPhaseNoiseMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Fluctuations in the
Phase of a Waveform for the interface in 1/1000 dB."
::= { coiOpticalCurrentEntry 11 }
coiOptCurrentLBCMax OBJECT-TYPE
SYNTAX Integer32 (0..1000)
UNITS "1/10 %"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current max Laser Bias Current in
1/10% for the interface."
::= { coiOpticalCurrentEntry 12 }
coiOptCurrentTXPowerMin OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Transmit power for the
interface in 1/100 dBm."
::= { coiOpticalCurrentEntry 13 }
coiOptCurrentRXPowerMin OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Receive power for the
interface in 1/100 dBm."
::= { coiOpticalCurrentEntry 14 }
coiOptCurrentOSNRMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Optical Signal to Noise
Ratio for the interface in 1/100 dB."
::= { coiOpticalCurrentEntry 15 }
coiOptCurrentChromaticDispersionMin OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min measure of spread of
light pulse for the interface in ps/nm."
::= { coiOpticalCurrentEntry 16 }
coiOptCurrentDifferentialGroupDelayMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min propagation time
difference between eigenmodes X and Y for the interface in
1/100 ps."
::= { coiOpticalCurrentEntry 17 }
coiOptCurrentSecondOrderPMDMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Second Order
Polarization Mode Dispersion for the interface in 1/100 ps^2."
::= { coiOpticalCurrentEntry 18 }
coiOptCurrentPolarizationDependentLossMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Polarization Dependent
Loss for the interface in 1/100 dB."
::= { coiOpticalCurrentEntry 19 }
coiOptCurrentPolarizationChangeRateMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Polarization Change Rate
for the interface in 1/100 rad/s."
::= { coiOpticalCurrentEntry 20 }
coiOptCurrentPhaseNoiseMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Fluctuations in the
Phase of a Waveform in 1/1000 dB for the interface."
::= { coiOpticalCurrentEntry 21 }
coiOptCurrentLBCMin OBJECT-TYPE
SYNTAX Integer32 (0..1000)
UNITS "1/10 %"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current min Laser Bias Current in
1/10% for the interface."
::= { coiOpticalCurrentEntry 22 }
coiOptCurrentTXPowerAvg OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Transmit power
for the interface in 1/100 dBm."
::= { coiOpticalCurrentEntry 23 }
coiOptCurrentRXPowerAvg OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Receive power
for the interface in 1/100 dBm."
::= { coiOpticalCurrentEntry 24 }
coiOptCurrentOSNRAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Optical Signal to
Noise Ratio for the interface in 1/100 dB."
::= { coiOpticalCurrentEntry 25 }
coiOptCurrentChromaticDispersionAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average measure of spread of
light pulse for the interface in ps/nm."
::= { coiOpticalCurrentEntry 26 }
coiOptCurrentDifferentialGroupDelayAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average propagation time
difference between eigenmodes X and Y for the interface in
1/100 ps."
::= { coiOpticalCurrentEntry 27 }
coiOptCurrentSecondOrderPMDAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Second Order
Polarization Mode Dispersion for the interface in 1/100 ps^2."
::= { coiOpticalCurrentEntry 28 }
coiOptCurrentPolarizationDependentLossAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Polarization
Dependent Loss for the interface in 1/100 dB."
::= { coiOpticalCurrentEntry 29 }
coiOptCurrentPolarizationChangeRateAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Polarization Change
Rate for the interface in 1/100 rad/s."
::= { coiOpticalCurrentEntry 30 }
coiOptCurrentPhaseNoiseAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Fluctuations in the
Phase of a Waveform in 1/1000 dB for the interface."
::= { coiOpticalCurrentEntry 31 }
coiOptCurrentLBCAvg OBJECT-TYPE
SYNTAX Integer32 (0..1000)
UNITS "1/10 %"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the current average Laser Bias Current
in 1/10% for the interface."
::= { coiOpticalCurrentEntry 32 }
coiOptCurrentTimestamp OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the timestamp for
the current bucket for the interface."
::= { coiOpticalCurrentEntry 33 }
coiOpticalIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF CoiOpticalIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides interval information for optical layer
related attributes of interfaces with an ifType of
opticalChannel(195), lane as coiOptIntervalLane, Interval as
coiOptIntervalIntervalType and history bucket as
coiOptIntervalIntervalType."
::= { coiOpticalPerformanceMonitoring 3 }
coiOpticalIntervalEntry OBJECT-TYPE
SYNTAX CoiOpticalIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing interval information on optical layer
related attributes of interfaces with an ifType
opticalChannel(195). Entries are created by the feature when a
new interface is added to the ifTable."
INDEX {
ifIndex,
coiOptIntervalLane,
coiOptIntervalIntervalType,
coiOptIntervalNum
}
::= { coiOpticalIntervalTable 1 }
CoiOpticalIntervalEntry ::= SEQUENCE {
coiOptIntervalLane Integer32,
coiOptIntervalIntervalType CoiIntervalType,
coiOptIntervalNum Integer32,
coiOptIntervalTXPowerMax CoiOpticalPower,
coiOptIntervalRXPowerMax CoiOpticalPower,
coiOptIntervalOSNRMax Integer32,
coiOptIntervalChromaticDispersionMax Integer32,
coiOptIntervalDifferentialGroupDelayMax Integer32,
coiOptIntervalSecondOrderPMDMax Integer32,
coiOptIntervalPolarizationDependentLossMax Integer32,
coiOptIntervalPolarizationChangeRateMax Integer32,
coiOptIntervalPhaseNoiseMax Integer32,
coiOptIntervalLBCMax Integer32,
coiOptIntervalTXPowerMin CoiOpticalPower,
coiOptIntervalRXPowerMin CoiOpticalPower,
coiOptIntervalOSNRMin Integer32,
coiOptIntervalChromaticDispersionMin Integer32,
coiOptIntervalDifferentialGroupDelayMin Integer32,
coiOptIntervalSecondOrderPMDMin Integer32,
coiOptIntervalPolarizationDependentLossMin Integer32,
coiOptIntervalPolarizationChangeRateMin Integer32,
coiOptIntervalPhaseNoiseMin Integer32,
coiOptIntervalLBCMin Integer32,
coiOptIntervalTXPowerAvg CoiOpticalPower,
coiOptIntervalRXPowerAvg CoiOpticalPower,
coiOptIntervalOSNRAvg Integer32,
coiOptIntervalChromaticDispersionAvg Integer32,
coiOptIntervalDifferentialGroupDelayAvg Integer32,
coiOptIntervalSecondOrderPMDAvg Integer32,
coiOptIntervalPolarizationDependentLossAvg Integer32,
coiOptIntervalPolarizationChangeRateAvg Integer32,
coiOptIntervalPhaseNoiseAvg Integer32,
coiOptIntervalLBCAvg Integer32,
coiOptIntervalTimestamp OCTET STRING
}
coiOptIntervalLane OBJECT-TYPE
SYNTAX Integer32 (1..12)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the lane number for the optical
interface. Each optical controller is divided into data lanes
with each lane operating at some data rate, giving an aggregated
bandwidth of the controller as a whole.Lane is applicable for
breakout mode of operation."
::= { coiOpticalIntervalEntry 1 }
coiOptIntervalIntervalType OBJECT-TYPE
SYNTAX CoiIntervalType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object gives the interval type during which the
performance statistics are accumulated."
::= { coiOpticalIntervalEntry 2 }
coiOptIntervalNum OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the interval for which the set of
interval performance values is available.
The interval identified by 1 is the most recent 15 minute
or 24 hour interval, and the interval identified by N is
the interval immediately preceding the one identified by N-1."
::= { coiOpticalIntervalEntry 3 }
coiOptIntervalTXPowerMax OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Transmit power in
1/100 dBm for the interface."
::= { coiOpticalIntervalEntry 4 }
coiOptIntervalRXPowerMax OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Receive power in
1/100 dBm for the interface."
::= { coiOpticalIntervalEntry 5 }
coiOptIntervalOSNRMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Optical Signal to
Noise Ratio in 1/100 dB for the interface."
::= { coiOpticalIntervalEntry 6 }
coiOptIntervalChromaticDispersionMax OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum measure of spread
of light pulse for the interface in ps/nm."
::= { coiOpticalIntervalEntry 7 }
coiOptIntervalDifferentialGroupDelayMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum propagation time
difference between eigenmodes X and Y for the interface in
1/100 ps."
::= { coiOpticalIntervalEntry 8 }
coiOptIntervalSecondOrderPMDMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Second Order
Polarization Mode Dispersion in 1/100 ps^2 for the interface."
::= { coiOpticalIntervalEntry 9 }
coiOptIntervalPolarizationDependentLossMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Polarization
Dependent Loss in 1/100 dB for the interface."
::= { coiOpticalIntervalEntry 10 }
coiOptIntervalPolarizationChangeRateMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Polarization Change
Rate in 1/100 rad/s for the interface."
::= { coiOpticalIntervalEntry 11 }
coiOptIntervalPhaseNoiseMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Fluctuations in
the Phase of a Waveform in 1/1000 dB for the interface."
::= { coiOpticalIntervalEntry 12 }
coiOptIntervalLBCMax OBJECT-TYPE
SYNTAX Integer32
UNITS "1/10 %"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval maximum Laser Bias Current
in 1/10% for the interface."
::= { coiOpticalIntervalEntry 13 }
coiOptIntervalTXPowerMin OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Transmit power in
1/100 dBm for the interface."
::= { coiOpticalIntervalEntry 14 }
coiOptIntervalRXPowerMin OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Receive power in
1/100 dBm for the interface."
::= { coiOpticalIntervalEntry 15 }
coiOptIntervalOSNRMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Optical Signal to
Noise Ratio in 1/100 dB for the interface."
::= { coiOpticalIntervalEntry 16 }
coiOptIntervalChromaticDispersionMin OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum measure of spread
of light pulse in ps/nm for the interface."
::= { coiOpticalIntervalEntry 17 }
coiOptIntervalDifferentialGroupDelayMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum propagation time
difference between eigenmodes X and Y in 1/100 ps for the
interface."
::= { coiOpticalIntervalEntry 18 }
coiOptIntervalSecondOrderPMDMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Second Order
Polarization Mode Dispersion in 1/100 ps^2 for the interface."
::= { coiOpticalIntervalEntry 19 }
coiOptIntervalPolarizationDependentLossMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Polarization
Dependent Loss in 1/100 dB for the interface."
::= { coiOpticalIntervalEntry 20 }
coiOptIntervalPolarizationChangeRateMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Polarization Change
Rate in 1/100 rad/s for the interface."
::= { coiOpticalIntervalEntry 21 }
coiOptIntervalPhaseNoiseMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Fluctuations in the
Phase of a Waveform in 1/1000 dB for the interface."
::= { coiOpticalIntervalEntry 22 }
coiOptIntervalLBCMin OBJECT-TYPE
SYNTAX Integer32
UNITS "1/10 %"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval minimum Laser Bias Current
in 1/10% for the interface."
::= { coiOpticalIntervalEntry 23 }
coiOptIntervalTXPowerAvg OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Transmit power in
1/100 dBm for the interface."
::= { coiOpticalIntervalEntry 24 }
coiOptIntervalRXPowerAvg OBJECT-TYPE
SYNTAX CoiOpticalPower
UNITS "1/100 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Receive power in
1/100 dBm for the interface."
::= { coiOpticalIntervalEntry 25 }
coiOptIntervalOSNRAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Optical Signal to
Noise Ratio in 1/100 dB for the interface."
::= { coiOpticalIntervalEntry 26 }
coiOptIntervalChromaticDispersionAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "ps/nm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average measure of spread
of light pulse in ps/nm for the interface."
::= { coiOpticalIntervalEntry 27 }
coiOptIntervalDifferentialGroupDelayAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average propagation time
difference between eigenmodes X and Y in 1/100 ps for the
interface."
::= { coiOpticalIntervalEntry 28 }
coiOptIntervalSecondOrderPMDAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 ps^2"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Second Order
Polarization Mode Dispersion in 1/100 ps^2 for the interface."
::= { coiOpticalIntervalEntry 29 }
coiOptIntervalPolarizationDependentLossAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Polarization
Dependent Loss in 1/100 dB for the interface."
::= { coiOpticalIntervalEntry 30 }
coiOptIntervalPolarizationChangeRateAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/100 rad/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Polarization Change
Rate in 1/100 rad/s for the interface."
::= { coiOpticalIntervalEntry 31 }
coiOptIntervalPhaseNoiseAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/1000 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Fluctuations in
the Phase of a Waveform in 1/1000 dB for the interface."
::= { coiOpticalIntervalEntry 32 }
coiOptIntervalLBCAvg OBJECT-TYPE
SYNTAX Integer32
UNITS "1/10 %"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval average Laser Bias Current
in 1/10 % for the interface."
::= { coiOpticalIntervalEntry 33 }
coiOptIntervalTimestamp OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the timestamp, for the bucket specified
by 'coiOptIntervalNum', for the interface."
::= { coiOpticalIntervalEntry 34 }
coiOpticalEquipmentAlarmGroup OBJECT IDENTIFIER
::= { ciscoOpticalMIBObjects 4 }
coiOpticalAlarmLocation OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object indicates the location of the component that
raised alarm, within the device."
::= { coiOpticalEquipmentAlarmGroup 1 }
coiOpticalAlarmType OBJECT-TYPE
SYNTAX CoiOptAlarmType
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object indicates the type of alarm that is raised."
::= { coiOpticalEquipmentAlarmGroup 2 }
coiOpticalAlarmTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object gives the time when an event occurred. This is
accurate only upto a second."
::= { coiOpticalEquipmentAlarmGroup 3 }
coiOpticalAlarmName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This variable gives the user-visible name, which
uniquely identifies the alarm in the system."
::= { coiOpticalEquipmentAlarmGroup 4 }
coiOpticalAlarmAdditionalInfo OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This variable provides additional info about the alarm. This
object would be a null string if no additional information is
specified."
::= { coiOpticalEquipmentAlarmGroup 5 }
coiOpticalAlarmSeverity OBJECT-TYPE
SYNTAX CoiOptAlarmSeverity
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This variable specifies alarm severity."
::= { coiOpticalEquipmentAlarmGroup 6 }
coiOpticalAlarmStatus OBJECT-TYPE
SYNTAX CoiOptAlarmStatus
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This variable specifies alarm status."
::= { coiOpticalEquipmentAlarmGroup 7 }
coiOpticalAlarmServiceAffecting OBJECT-TYPE
SYNTAX CoiOptAlarmServiceAffecting
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This variable specifies the service affecting state of the
alarm."
::= { coiOpticalEquipmentAlarmGroup 8 }
-- MIB Conformance Statements
ciscoOpticalMIBConformance OBJECT IDENTIFIER
::= { ciscoOpticalMIB 2 }
ciscoOpticalMIBCompliances OBJECT IDENTIFIER
::= { ciscoOpticalMIBConformance 1 }
ciscoOpticalMIBGroups OBJECT IDENTIFIER
::= { ciscoOpticalMIBConformance 2 }
ciscoOpticalMIBCompliance MODULE-COMPLIANCE
STATUS deprecated -- superceded by
-- ciscoOpticalMIBComplianceRev1
DESCRIPTION
"The compliance statement for platforms that monitor the
parameters for the optical interfaces."
MODULE -- this module
MANDATORY-GROUPS {
coiOpticalGroup
}
GROUP coiOpticalControllerGroup
DESCRIPTION
"The collection of objects to allow configurations and give
information related to the optical layer characteristics
for interfaces of ifType opticalChannel(195)."
GROUP coiOpticalControllerPerLaneGroup
DESCRIPTION
"The collection of objects to give information related to
the optical layer characteristics for interfaces of ifType
opticalChannel(195) and lane number as
coiOpticalControllerLane."
GROUP coiOpticalClientInfoGroup
DESCRIPTION
"The collection of objects to give information related to
optical's client layer related attributes of interfaces with an
ifType of ethernetCsmacd(6)."
GROUP coiOpticalThresholdGroup
DESCRIPTION
"The collection of objects used for monitoring the threshold
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195)."
GROUP coiOpticalCurrentGroup
DESCRIPTION
"The collection of objects used for monitoring the current
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195) in a current interval."
GROUP coiOpticalIntervalGroup
DESCRIPTION
"The collection of objects used for monitoring the interval
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195) in a given interval."
GROUP coiOpticalNotifEnableGroup
DESCRIPTION
"The collection of objects to enable the notification
generations upon an interface's defect status change on optics
layer."
GROUP coiOpticalNotifStatusObjectGroup
DESCRIPTION
"The object to be included in an Optical interface's
defect status change notification."
GROUP coiOpticalNotifGroup
DESCRIPTION
"The optical status change notifications whenever the
defect status of optical layer on an interface changes."
GROUP coiOpticalEquipmentAlarmInfoGroup
DESCRIPTION
"The optical equipment alarm notifications whenever the
equipment failed alarm is detected."
::= { ciscoOpticalMIBCompliances 1 }
ciscoOpticalMIBComplianceRev1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for platforms that monitor the
parameters for the optical interfaces."
MODULE -- this module
MANDATORY-GROUPS {
coiOpticalGroup
}
GROUP coiOpticalControllerGroup
DESCRIPTION
"The collection of objects to allow configurations and give
information related to the optical layer characteristics
for interfaces of ifType opticalChannel(195)."
GROUP coiOpticalControllerPerLaneGroup
DESCRIPTION
"The collection of objects to give information related to
the optical layer characteristics for interfaces of ifType
opticalChannel(195) and lane number as
coiOpticalControllerLane."
GROUP coiOpticalClientInfoGroup
DESCRIPTION
"The collection of objects to give information related to
optical's client layer related attributes of interfaces with an
ifType of ethernetCsmacd(6)."
GROUP coiOpticalThresholdGroup
DESCRIPTION
"The collection of objects used for monitoring the threshold
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195)."
GROUP coiOpticalCurrentGroup
DESCRIPTION
"The collection of objects used for monitoring the current
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195) in a current interval."
GROUP coiOpticalIntervalGroup
DESCRIPTION
"The collection of objects used for monitoring the interval
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195) in a given interval."
GROUP coiOpticalNotifEnableGroup
DESCRIPTION
"The collection of objects to enable the notification
generations upon an interface's defect status change on optics
layer."
GROUP coiOpticalNotifStatusObjectGroup
DESCRIPTION
"The object to be included in an Optical interface's
defect status change notification."
GROUP coiOpticalNotifGroup
DESCRIPTION
"The optical status change notifications whenever the
defect status of optical layer on an interface changes."
GROUP coiOpticalEquipmentAlarmInfoGroup
DESCRIPTION
"The optical equipment alarm notifications whenever the
equipment failed alarm is detected."
GROUP coiOpticalPowerGroup
DESCRIPTION
"The collection of objects used for monitoring the total power
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195)."
::= { ciscoOpticalMIBCompliances 2 }
-- units of conformance
coiOpticalGroup OBJECT-GROUP
OBJECTS {
coiOpticalControllerLaserStatus,
coiOpticalControllerTransmitPower,
coiOpticalControllerOpticsType,
coiOpticalControllerRXLowThreshold,
coiOpticalControllerTXLowThreshold,
coiOpticalControllerRXHighThreshold,
coiOpticalControllerTXHighThreshold,
coiOpticalControllerLBCHighThreshold,
coiOpticalControllerPerLaneRXPower,
coiOpticalControllerPerLaneTXPower,
coiOpticalControllerPerLaneLBC,
coiOpticalControllerStatus,
coiOptThreshTXPowerMin,
coiOptThreshRXPowerMin,
coiOptThreshLBCMin,
coiOptThreshTXPowerMax,
coiOptThreshRXPowerMax,
coiOptThreshLBCMax,
coiOptCurrentTXPowerMax,
coiOptCurrentRXPowerMax,
coiOptCurrentLBCMax,
coiOptCurrentTXPowerMin,
coiOptCurrentRXPowerMin,
coiOptCurrentLBCMin,
coiOptCurrentTXPowerAvg,
coiOptCurrentRXPowerAvg,
coiOptCurrentLBCAvg,
coiOptIntervalTXPowerMax,
coiOptIntervalRXPowerMax,
coiOptIntervalLBCMax,
coiOptIntervalTXPowerMin,
coiOptIntervalRXPowerMin,
coiOptIntervalLBCMin,
coiOptIntervalTXPowerAvg,
coiOptIntervalRXPowerAvg,
coiOptIntervalLBCAvg
}
STATUS current
DESCRIPTION
"The collection of objects to give information related to the
optical layer characteristics for interfaces of ifType
opticalChannel(195)."
::= { ciscoOpticalMIBGroups 1 }
coiOpticalControllerGroup OBJECT-GROUP
OBJECTS {
coiOpticalControllerWavelength,
coiOpticalControllerLaserStatus,
coiOpticalControllerFrequency,
coiOpticalControllerChannelNumber,
coiOpticalControllerTransmitPower,
coiOpticalControllerOpticsType,
coiOpticalControllerRXLowThreshold,
coiOpticalControllerTXLowThreshold,
coiOpticalControllerRXHighThreshold,
coiOpticalControllerTXHighThreshold,
coiOpticalControllerLBCHighThreshold,
coiOpticalControllerStatus,
coiOpticalControllerPortType
}
STATUS current
DESCRIPTION
"The collection of objects to allow configurations and give
information related to the optical layer characteristics
for interfaces of ifType opticalChannel(195)."
::= { ciscoOpticalMIBGroups 2 }
coiOpticalControllerPerLaneGroup OBJECT-GROUP
OBJECTS {
coiOpticalControllerPerLaneRXPower,
coiOpticalControllerPerLaneTXPower,
coiOpticalControllerPerLaneLBC,
coiOpticalControllerPerLaneOSNR,
coiOpticalControllerPerLaneChromaticDispersion,
coiOpticalControllerPerLaneDifferentialGroupDelay,
coiOpticalControllerPerLaneSecondOrderPMD,
coiOpticalControllerPerLanePolarizationDependentLoss,
coiOpticalControllerPerLanePolarizationChangeRate,
coiOpticalControllerPerLanePhaseNoise
}
STATUS current
DESCRIPTION
"The collection of objects to give information related to
the optical layer characteristics for interfaces of ifType
opticalChannel(195) and lane number as
coiOpticalControllerLane."
::= { ciscoOpticalMIBGroups 3 }
coiOpticalClientInfoGroup OBJECT-GROUP
OBJECTS {
coiOpticalClientEthernetNeighbourMAC
}
STATUS current
DESCRIPTION
"The collection of objects to give information related to
optical's client layer related attributes of interfaces with an
ifType of ethernetCsmacd(6)."
::= { ciscoOpticalMIBGroups 4 }
coiOpticalThresholdGroup OBJECT-GROUP
OBJECTS {
coiOptThreshTXPowerMin,
coiOptThreshRXPowerMin,
coiOptThreshOSNRMin,
coiOptThreshChromaticDispersionMin,
coiOptThreshDifferentialGroupDelayMin,
coiOptThreshSecondOrderPMDMin,
coiOptThreshPolarizationDependentLossMin,
coiOptThreshPolarizationChangeRateMin,
coiOptThreshPhaseNoiseMin,
coiOptThreshLBCMin,
coiOptThreshTXPowerMax,
coiOptThreshRXPowerMax,
coiOptThreshOSNRMax,
coiOptThreshChromaticDispersionMax,
coiOptThreshDifferentialGroupDelayMax,
coiOptThreshSecondOrderPMDMax,
coiOptThreshPolarizationDependentLossMax,
coiOptThreshPolarizationChangeRateMax,
coiOptThreshPhaseNoiseMax,
coiOptThreshLBCMax,
coiOptThreshTXPowerEnableMin,
coiOptThreshRXPowerEnableMin,
coiOptThreshOSNREnableMin,
coiOptThreshChromaticDispersionEnableMin,
coiOptThreshDifferentialGroupDelayEnableMin,
coiOptThreshSecondOrderPMDEnableMin,
coiOptThreshPolarizationDependentLossEnableMin,
coiOptThreshPolarizationChangeRateEnableMin,
coiOptThreshPhaseNoiseEnableMin,
coiOptThreshLBCEnableMin,
coiOptThreshTXPowerEnableMax,
coiOptThreshRXPowerEnableMax,
coiOptThreshOSNREnableMax,
coiOptThreshChromaticDispersionEnableMax,
coiOptThreshDifferentialGroupDelayEnableMax,
coiOptThreshSecondOrderPMDEnableMax,
coiOptThreshPolarizationDependentLossEnableMax,
coiOptThreshPolarizationChangeRateEnableMax,
coiOptThreshPhaseNoiseEnableMax,
coiOptThreshLBCEnableMax
}
STATUS current
DESCRIPTION
"The collection of objects used for monitoring the threshold
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195)."
::= { ciscoOpticalMIBGroups 5 }
coiOpticalCurrentGroup OBJECT-GROUP
OBJECTS {
coiOptCurrentTXPowerMax,
coiOptCurrentRXPowerMax,
coiOptCurrentOSNRMax,
coiOptCurrentChromaticDispersionMax,
coiOptCurrentDifferentialGroupDelayMax,
coiOptCurrentSecondOrderPMDMax,
coiOptCurrentPolarizationDependentLossMax,
coiOptCurrentPolarizationChangeRateMax,
coiOptCurrentPhaseNoiseMax,
coiOptCurrentLBCMax,
coiOptCurrentTXPowerMin,
coiOptCurrentRXPowerMin,
coiOptCurrentOSNRMin,
coiOptCurrentChromaticDispersionMin,
coiOptCurrentDifferentialGroupDelayMin,
coiOptCurrentSecondOrderPMDMin,
coiOptCurrentPolarizationDependentLossMin,
coiOptCurrentPolarizationChangeRateMin,
coiOptCurrentPhaseNoiseMin,
coiOptCurrentLBCMin,
coiOptCurrentTXPowerAvg,
coiOptCurrentRXPowerAvg,
coiOptCurrentOSNRAvg,
coiOptCurrentChromaticDispersionAvg,
coiOptCurrentDifferentialGroupDelayAvg,
coiOptCurrentSecondOrderPMDAvg,
coiOptCurrentPolarizationDependentLossAvg,
coiOptCurrentPolarizationChangeRateAvg,
coiOptCurrentPhaseNoiseAvg,
coiOptCurrentLBCAvg,
coiOptCurrentTimestamp
}
STATUS current
DESCRIPTION
"The collection of objects used for monitoring the current
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195) in a current interval."
::= { ciscoOpticalMIBGroups 6 }
coiOpticalIntervalGroup OBJECT-GROUP
OBJECTS {
coiOptIntervalTXPowerMax,
coiOptIntervalRXPowerMax,
coiOptIntervalOSNRMax,
coiOptIntervalChromaticDispersionMax,
coiOptIntervalDifferentialGroupDelayMax,
coiOptIntervalSecondOrderPMDMax,
coiOptIntervalPolarizationDependentLossMax,
coiOptIntervalPolarizationChangeRateMax,
coiOptIntervalPhaseNoiseMax,
coiOptIntervalLBCMax,
coiOptIntervalTXPowerMin,
coiOptIntervalRXPowerMin,
coiOptIntervalOSNRMin,
coiOptIntervalChromaticDispersionMin,
coiOptIntervalDifferentialGroupDelayMin,
coiOptIntervalSecondOrderPMDMin,
coiOptIntervalPolarizationDependentLossMin,
coiOptIntervalPolarizationChangeRateMin,
coiOptIntervalPhaseNoiseMin,
coiOptIntervalLBCMin,
coiOptIntervalTXPowerAvg,
coiOptIntervalRXPowerAvg,
coiOptIntervalOSNRAvg,
coiOptIntervalChromaticDispersionAvg,
coiOptIntervalDifferentialGroupDelayAvg,
coiOptIntervalSecondOrderPMDAvg,
coiOptIntervalPolarizationDependentLossAvg,
coiOptIntervalPolarizationChangeRateAvg,
coiOptIntervalPhaseNoiseAvg,
coiOptIntervalLBCAvg,
coiOptIntervalTimestamp
}
STATUS current
DESCRIPTION
"The collection of objects used for monitoring the interval
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195) in a given interval."
::= { ciscoOpticalMIBGroups 7 }
coiOpticalNotifEnableGroup OBJECT-GROUP
OBJECTS { coiOpticalNotifEnabled }
STATUS current
DESCRIPTION
"The collection of objects to enable the notification
generations upon an interface's defect status change on optics
layer."
::= { ciscoOpticalMIBGroups 8 }
coiOpticalNotifStatusObjectGroup OBJECT-GROUP
OBJECTS { coiOpticalControllerStatus }
STATUS current
DESCRIPTION
"The object to be included in an Optical interface's
defect status change notification."
::= { ciscoOpticalMIBGroups 9 }
coiOpticalNotifGroup NOTIFICATION-GROUP
NOTIFICATIONS {
coiOpticsStatusChange,
coiOpticalEquipmentAlarm
}
STATUS current
DESCRIPTION
"The optical status change notifications whenever the
defect status of optical layer on an interface changes."
::= { ciscoOpticalMIBGroups 10 }
coiOpticalEquipmentAlarmInfoGroup OBJECT-GROUP
OBJECTS {
coiOpticalAlarmLocation,
coiOpticalAlarmType,
coiOpticalAlarmTimeStamp,
coiOpticalAlarmName,
coiOpticalAlarmAdditionalInfo,
coiOpticalAlarmSeverity,
coiOpticalAlarmStatus,
coiOpticalAlarmServiceAffecting
}
STATUS current
DESCRIPTION
"The optical equipment notifications whenever the
alarm is generated."
::= { ciscoOpticalMIBGroups 11 }
coiOpticalPowerGroup OBJECT-GROUP
OBJECTS {
coiOpticalControllerTotalRXPower,
coiOpticalControllerTotalTXPower
}
STATUS current
DESCRIPTION
"The collection of objects used for monitoring the total power
information for optical layer related attributes of interfaces
with an ifType of opticalChannel(195)."
::= { ciscoOpticalMIBGroups 12 }
END
View Git Blame Copy Permalink