1875 lines
65 KiB
Plaintext
1875 lines
65 KiB
Plaintext
-- *****************************************************************
|
|
-- CISCO-NETSYNC-MIB.my: Cisco SyncE MIB
|
|
--
|
|
-- October 2010, Danny Lee
|
|
--
|
|
-- Copyright (c) 2010 by cisco Systems Inc.
|
|
-- All rights reserved.
|
|
--
|
|
-- *****************************************************************
|
|
|
|
CISCO-NETSYNC-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE,
|
|
NOTIFICATION-TYPE,
|
|
Gauge32,
|
|
Unsigned32
|
|
FROM SNMPv2-SMI
|
|
MODULE-COMPLIANCE,
|
|
NOTIFICATION-GROUP,
|
|
OBJECT-GROUP
|
|
FROM SNMPv2-CONF
|
|
TruthValue,
|
|
TEXTUAL-CONVENTION,
|
|
TimeStamp
|
|
FROM SNMPv2-TC
|
|
SnmpAdminString
|
|
FROM SNMP-FRAMEWORK-MIB
|
|
ciscoMgmt
|
|
FROM CISCO-SMI;
|
|
|
|
|
|
ciscoNetsyncMIB MODULE-IDENTITY
|
|
LAST-UPDATED "201010150000Z"
|
|
ORGANIZATION "Cisco Systems, Inc."
|
|
CONTACT-INFO
|
|
"Cisco Systems
|
|
Customer Service
|
|
|
|
|
|
Postal: 170 W Tasman Drive
|
|
|
|
San Jose, CA 95134
|
|
|
|
USA
|
|
|
|
|
|
Tel: +1 800 553-NETS
|
|
|
|
|
|
E-mail: cs-sync-e@cisco.com"
|
|
DESCRIPTION
|
|
"The Synchronous Ethernet (SyncE) MIB is defined
|
|
for monitoring network synchronization based on
|
|
ITU-T G.781 clock selection.
|
|
|
|
Synchronous Ethernet (SyncE) is a standard defined
|
|
for delivering timing to the remote NEs through a
|
|
Packet Network. SyncE is well defined by ITU-T
|
|
which included G.8261, G.8262, G.8264 and G.781.
|
|
It leverages the PHY layer of Ethernet to transmit
|
|
frequency to the remote sites. Its functionality
|
|
and accuracy mimics that of the SONET/SDH network
|
|
because of its physical layer characteristic.
|
|
In order to allow best clock source traceabiliy,
|
|
correctly define the timing source and helps
|
|
preventing timing loop, Synchronization Status
|
|
Message is required for SyncE. This is similar
|
|
to SONET/SDH. However, since SONET/SDH use 4 bits
|
|
from the two S bytes in the SONET/SDH overhead
|
|
frame for such message, Ethernet relies on a
|
|
different channel called ESMC (Ethernet
|
|
Synchronization Messaging Channel) which is based
|
|
on IEEE 802.3 Organization Specific Slow Protocol.
|
|
|
|
Glossary:
|
|
AIS: Alarm Indication Signal
|
|
ATM: Asynchronous Transfer Mode
|
|
EEC: Ethernet Equipment Clock
|
|
ESMC: Ethernet Synchronization Messaging Channel
|
|
QL: Quality Level
|
|
SASE: Stand Alone Synchronization Equipment
|
|
SSM: Synchronization Status Messaging"
|
|
REVISION "201010150000Z"
|
|
DESCRIPTION
|
|
"Initial version of the SyncE MIB module."
|
|
::= { ciscoMgmt 761 }
|
|
|
|
|
|
|
|
-- Textual Conventions
|
|
|
|
CiscoNetsyncIfType ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network synchronization clock source Interface type.
|
|
|
|
Netsync interface Interface type
|
|
======================== ==============
|
|
netsyncIfTypeUnknown Unknown
|
|
netsyncIfTypeInternal Internal
|
|
netsyncIfTypeEthernet Ethernet
|
|
netsyncIfTypeSonet SONET
|
|
netsyncIfTypeTop Timing Over Packet
|
|
netsyncIfTypeExt External interface
|
|
netsyncIfTypeController T1/E1 Controller
|
|
netsyncIfTypeGps GPS
|
|
netsyncIfTypeAtm ATM
|
|
|
|
For external and GPS interface types, the following
|
|
syntax is used for specifying an interface:
|
|
<slot>/<card>/<port> <signal type> where
|
|
slot : slot number of the device where card is present.
|
|
card : bay number in which card is inserted.
|
|
port : port number on the card.
|
|
signal type: hardware signal of the specified
|
|
<slot>/<card>/<port>. Examples of signal
|
|
type are T1 SF and T1 ESF.
|
|
"
|
|
SYNTAX INTEGER {
|
|
netsyncIfTypeUnknown(1),
|
|
netsyncIfTypeInternal(2),
|
|
netsyncIfTypeEthernet(3),
|
|
netsyncIfTypeSonet(4),
|
|
netsyncIfTypeTop(5),
|
|
netsyncIfTypeExt(6),
|
|
netsyncIfTypeController(7),
|
|
netsyncIfTypeGps(8),
|
|
netsyncIfTypeAtm(9)
|
|
}
|
|
|
|
CiscoNetsyncNetworkOption ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network synchronization networking options.
|
|
|
|
Network option Network option type
|
|
=========================== ===================
|
|
netsyncNetworkOptionUnknown Unknown network option
|
|
netsyncNetworkOption1 Option I
|
|
netsyncNetworkOption2Gen1 Option II Generation 1
|
|
netsyncNetworkOption2Gen2 Option II Generation 2
|
|
netsyncNetworkOption3 Option III
|
|
netsyncNetworkOptionInvalid Invalid network option
|
|
|
|
Option I refers to ITU-T Option I synchronization networks.
|
|
|
|
Option II refers to ITU-T Option II synchronization networks
|
|
designed for North America.
|
|
|
|
Option III refers to ITU-T Option III synchronization networks
|
|
designed for Japan.
|
|
"
|
|
REFERENCE "ITU-T standard G.781"
|
|
SYNTAX INTEGER {
|
|
netsyncNetworkOptionUnknown(1),
|
|
netsyncNetworkOption1(2),
|
|
netsyncNetworkOption2Gen1(3),
|
|
netsyncNetworkOption2Gen2(4),
|
|
netsyncNetworkOption3(5),
|
|
netsyncNetworkOptionInvalid(6)
|
|
}
|
|
|
|
CiscoNetsyncEECOption ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network synchronization EEC (Ethernet Equipment Clock)
|
|
options.
|
|
|
|
The EEC options are for Synchronous Ethernet devices and define
|
|
the requirements for clocks, e.g. bandwidth, frequency accuracy,
|
|
holdover and noise generation.
|
|
|
|
Two options are defined:
|
|
EEC-Option 1: Designed to interwork with network optimized for
|
|
the 2048 kbit/s hierarchy.
|
|
|
|
EEC-Option 2: Designed to interwork with network optimized for
|
|
the 1544 kbit/s hierarchy.
|
|
|
|
netsyncEECOptionUnknown Unknown
|
|
netsyncEECOption1 EEC option 1
|
|
netsyncEECOption2 EEC option 2
|
|
netsyncEECOptionInvalid Invalid EEC option
|
|
"
|
|
|
|
REFERENCE "ITU-T standard G.781"
|
|
SYNTAX INTEGER {
|
|
netsyncEECOptionUnknown(1),
|
|
netsyncEECOption1(2),
|
|
netsyncEECOption2(3),
|
|
netsyncEECOptionInvalid(4)
|
|
}
|
|
|
|
CiscoNetsyncQLMode ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The clock mode of the network synchronization clock selection
|
|
process as described in ITU-T standard G.781 section 5.12.
|
|
|
|
G.781 clock selection runs in one of two clock modes:
|
|
QL (Quality Level) enabled mode and QL disabled mode.
|
|
|
|
netsyncQLModeUnknown - QL mode unknown
|
|
netsyncQLModeQlDisabled - QL-disabled mode;
|
|
clock selection is running
|
|
in QL disabled mode,
|
|
which primarily considers
|
|
the source's priority as the
|
|
clock selection criteria.
|
|
netsyncQLModeQlEnabled - QL-enabled mode
|
|
clock selection is running
|
|
in QL enabled mode,
|
|
which primarily considers
|
|
the source's clock quality
|
|
level and priority as the
|
|
clock selection criteria.
|
|
"
|
|
REFERENCE "ITU-T standard G.781 section 5.12"
|
|
SYNTAX INTEGER {
|
|
netsyncQLModeUnknown(1),
|
|
netsyncQLModeQlDisabled(2),
|
|
netsyncQLModeQlEnabled(3)
|
|
}
|
|
|
|
CiscoNetsyncClockMode ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Clock operating mode:
|
|
|
|
netsyncClockModeUnknown - system is unable to
|
|
determine the operating mode.
|
|
netsyncClockModeFreerun - free-running mode.
|
|
netsyncClockModeHoldover - holdover mode.
|
|
netsyncClockModeLocked - a valid clock source is locked.
|
|
"
|
|
SYNTAX INTEGER {
|
|
netsyncClockModeUnknown(1),
|
|
netsyncClockModeFreerun(2),
|
|
netsyncClockModeHoldover(3),
|
|
netsyncClockModeLocked(4)
|
|
}
|
|
|
|
CiscoNetsyncQualityLevel ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Clock source QL (quality level) is defined in ITU-T G.781
|
|
section 5.4 to reflect the synchronization quality within a
|
|
network Option, i.e. I, II, and III.
|
|
|
|
The following clock source quality levels are defined for the
|
|
synchronization process of Option I:
|
|
|
|
QL-PRC Primary reference clock
|
|
QL-SSU-A Type I or V slave clock defined in ITU-T G.811
|
|
QL-SSU-B Type VI slave clock defined in ITU-T G.812
|
|
QL-SEC Synchronous equipment clock
|
|
QL-DNU Do not use for synchronization
|
|
QL-INVx Unallocated SSM value,
|
|
where x represent the value of SSM received
|
|
QL-FAILED Signal failure state
|
|
QL-UNC Unconnected to an input
|
|
QL-NSUPP Not supporting the SSM processing
|
|
|
|
The following clock source quality levels are defined for the
|
|
synchronization process of Option II:
|
|
|
|
QL-PRS PRS traceable
|
|
QL-STU Synchronized; traceability unknown
|
|
QL-ST2 Stratum 2
|
|
QL-TNC Transit node clock
|
|
QL-ST3E Stratum 3E
|
|
QL-ST3 Stratum 3
|
|
QL-SMC SONET clock self timed
|
|
QL-ST4 Stratum 4 freerun
|
|
QL-PROV Provisionable by the network operator
|
|
QL-DUS Do not use for synchronization
|
|
QL-INVx Unallocated SSM value,
|
|
where x represent the value of SSM received
|
|
QL-FAILED Signal failure state
|
|
QL-UNC Unconnected to an input
|
|
QL-NSUPP Not supporting the SSM processing
|
|
|
|
The following clock source quality levels are defined for the
|
|
synchronization process of Option III:
|
|
|
|
QL-UNK Unknown clock source
|
|
QL-SEC Synchronous equipment clock
|
|
|
|
QL-INVx Unallocated SSM value,
|
|
where x represent the value of SSM received
|
|
QL-FAILED Signal failure state
|
|
QL-UNC Unconnected to an input
|
|
QL-NSUPP Not supporting the SSM processing
|
|
"
|
|
REFERENCE "ITU-T standard G.781 section 5.4"
|
|
SYNTAX INTEGER {
|
|
netsyncQualityLevelNULL(1),
|
|
netsyncQualityLevelDNU(2),
|
|
netsyncQualityLevelDUS(3),
|
|
netsyncQualityLevelFAILED(4),
|
|
netsyncQualityLevelINV0(5),
|
|
netsyncQualityLevelINV1(6),
|
|
netsyncQualityLevelINV2(7),
|
|
netsyncQualityLevelINV3(8),
|
|
netsyncQualityLevelINV4(9),
|
|
netsyncQualityLevelINV5(10),
|
|
netsyncQualityLevelINV6(11),
|
|
netsyncQualityLevelINV7(12),
|
|
netsyncQualityLevelINV8(13),
|
|
netsyncQualityLevelINV9(14),
|
|
netsyncQualityLevelINV10(15),
|
|
netsyncQualityLevelINV11(16),
|
|
netsyncQualityLevelINV12(17),
|
|
netsyncQualityLevelINV13(18),
|
|
netsyncQualityLevelINV14(19),
|
|
netsyncQualityLevelINV15(20),
|
|
netsyncQualityLevelNSUPP(21),
|
|
netsyncQualityLevelPRC(22),
|
|
netsyncQualityLevelPROV(23),
|
|
netsyncQualityLevelPRS(24),
|
|
netsyncQualityLevelSEC(25),
|
|
netsyncQualityLevelSMC(26),
|
|
netsyncQualityLevelSSUA(27),
|
|
netsyncQualityLevelSSUB(28),
|
|
netsyncQualityLevelST2(29),
|
|
netsyncQualityLevelST3(30),
|
|
netsyncQualityLevelST3E(31),
|
|
netsyncQualityLevelST4(32),
|
|
netsyncQualityLevelSTU(33),
|
|
netsyncQualityLevelTNC(34),
|
|
netsyncQualityLevelUNC(35),
|
|
netsyncQualityLevelUNK(36)
|
|
}
|
|
|
|
CiscoNetsyncSSMCap ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network synchronization clock source interface SSM
|
|
(Synchronization Status Message) capability.
|
|
|
|
SSM Capability Capability information
|
|
===================== ======================
|
|
netsyncSSMCapNone No SSM capability
|
|
netsyncSSMCapTxRx To transmit and receive SSM
|
|
netsyncSSMCapTx To transmit SSM only
|
|
netsyncSSMCapRx To receive SSM only
|
|
netsyncSSMCapInvalid Capability invalid or unsupported
|
|
"
|
|
SYNTAX INTEGER {
|
|
netsyncSSMCapNone(1),
|
|
netsyncSSMCapTxRx(2),
|
|
netsyncSSMCapTx(3),
|
|
netsyncSSMCapRx(4),
|
|
netsyncSSMCapInvalid(5)
|
|
}
|
|
|
|
CiscoNetsyncESMCCap ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Network synchronization clock source interface ESMC
|
|
(Ethernet Synchronization Messaging Channel)
|
|
capability.
|
|
|
|
ESMC Capability Capability information
|
|
====================== ======================
|
|
netsyncESMCCapNone No ESMC capability
|
|
netsyncESMCCapTxRx To transmit and receive ESMC
|
|
netsyncESMCCapTx To transmit SSM only
|
|
netsyncESMCCapRx To receive SSM only
|
|
netsyncESMCCapInvalid Capability invalid or unsupported
|
|
"
|
|
SYNTAX INTEGER {
|
|
netsyncESMCCapNone(1),
|
|
netsyncESMCCapTxRx(2),
|
|
netsyncESMCCapTx(3),
|
|
netsyncESMCCapRx(4),
|
|
netsyncESMCCapInvalid(5)
|
|
}
|
|
|
|
CiscoNetsyncAlarmInfo ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Input clock source's alarm reasons:
|
|
|
|
netsyncSrcAlarmReasonAIS - Alarm Indication Signal
|
|
netsyncSrcAlarmReasonOOR - Out of range
|
|
netsyncSrcAlarmReasonOIR - Online Insertion Removal
|
|
netsyncSrcAlarmReasonInternal - Internal"
|
|
SYNTAX BITS {
|
|
netsyncSrcAlarmReasonAIS(0),
|
|
netsyncSrcAlarmReasonOOR(1),
|
|
netsyncSrcAlarmReasonOIR(2),
|
|
netsyncSrcAlarmReasonInternal(3)
|
|
}
|
|
-- Textual Conventions definition will be defined before this line
|
|
|
|
ciscoNetsyncMIBNotifs OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIB 0 }
|
|
|
|
ciscoNetsyncMIBObjects OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIB 1 }
|
|
|
|
ciscoNetsyncMIBConform OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIB 2 }
|
|
|
|
ciscoNetsyncMIBTables OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIBObjects 1 }
|
|
|
|
cnsClkSelGlobalTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CnsClkSelGlobalEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"G.781 clock selection process table.
|
|
This table contains the global parameters for the G.781 clock
|
|
selection process."
|
|
::= { ciscoNetsyncMIBTables 1 }
|
|
|
|
cnsClkSelGlobalEntry OBJECT-TYPE
|
|
SYNTAX CnsClkSelGlobalEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry is added to cnsClkSelGlobalTable when G.781 clock
|
|
selection is enabled in the device configuration. The entry
|
|
is removed when G.781 clock selection is removed from the
|
|
configuration."
|
|
INDEX { cnsClkSelGloProcIndex }
|
|
::= { cnsClkSelGlobalTable 1 }
|
|
|
|
CnsClkSelGlobalEntry ::= SEQUENCE {
|
|
cnsClkSelGloProcIndex Unsigned32,
|
|
cnsClkSelGlobProcessMode CiscoNetsyncQLMode,
|
|
cnsClkSelGlobClockMode CiscoNetsyncClockMode,
|
|
cnsClkSelGlobNetsyncEnable TruthValue,
|
|
cnsClkSelGlobRevertiveMode TruthValue,
|
|
cnsClkSelGlobESMCMode TruthValue,
|
|
cnsClkSelGlobEECOption CiscoNetsyncEECOption,
|
|
cnsClkSelGlobNetworkOption CiscoNetsyncNetworkOption,
|
|
cnsClkSelGlobHoldoffTime Unsigned32,
|
|
cnsClkSelGlobWtrTime Unsigned32,
|
|
cnsClkSelGlobNofSources Unsigned32,
|
|
cnsClkSelGlobLastHoldoverSeconds Gauge32,
|
|
cnsClkSelGlobCurrHoldoverSeconds Gauge32
|
|
}
|
|
|
|
cnsClkSelGloProcIndex OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index that uniquely represents a clock selection process.
|
|
|
|
This index is assigned arbitrarily by the system
|
|
and may not be persistent across reboots."
|
|
::= { cnsClkSelGlobalEntry 1 }
|
|
|
|
cnsClkSelGlobProcessMode OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQLMode
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the QL mode of
|
|
the network synchronization clock selection
|
|
process as described in ITU-T standard G.781
|
|
section 5.12.
|
|
"
|
|
::= { cnsClkSelGlobalEntry 2 }
|
|
|
|
cnsClkSelGlobClockMode OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncClockMode
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the operating mode
|
|
of the system clock."
|
|
::= { cnsClkSelGlobalEntry 3 }
|
|
|
|
cnsClkSelGlobNetsyncEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether the G.781
|
|
clock selection is enabled or not.
|
|
|
|
'true' - G.781 clock selection is enabled
|
|
'false' - G.781 clock selection is disabled"
|
|
DEFVAL { false }
|
|
::= { cnsClkSelGlobalEntry 4 }
|
|
|
|
cnsClkSelGlobRevertiveMode OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the revertive mode
|
|
setting in the G.781 clock selection process.
|
|
|
|
The switching of clock sources can be made revertive or
|
|
non-revertive. In non-revertive mode, an alternate
|
|
clock source is maintained even after the original clock
|
|
source has recovered from the failure that caused the switch.
|
|
In revertive mode, the clock selection process switches back
|
|
to the original clock source after recovering from the
|
|
failure."
|
|
DEFVAL { false }
|
|
::= { cnsClkSelGlobalEntry 5 }
|
|
|
|
cnsClkSelGlobESMCMode OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates if global ESMC is enabled.
|
|
With ESMC enabled globally, the system is capable
|
|
of handling ESMC messages."
|
|
DEFVAL { false }
|
|
::= { cnsClkSelGlobalEntry 6 }
|
|
|
|
cnsClkSelGlobEECOption OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncEECOption
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the network synchronization
|
|
EEC (Ethernet Equipment Clock) option."
|
|
REFERENCE "ITU-T standard G.781"
|
|
DEFVAL { netsyncEECOptionUnknown }
|
|
::= { cnsClkSelGlobalEntry 7 }
|
|
|
|
cnsClkSelGlobNetworkOption OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncNetworkOption
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the synchronization
|
|
network option."
|
|
REFERENCE "ITU-T standard G.781"
|
|
DEFVAL { netsyncNetworkOptionUnknown }
|
|
::= { cnsClkSelGlobalEntry 8 }
|
|
|
|
cnsClkSelGlobHoldoffTime OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the global
|
|
holdoff time in the G.781 clock
|
|
selection process."
|
|
REFERENCE "ITU-T standard G.781 section 5.8"
|
|
DEFVAL { 300 }
|
|
::= { cnsClkSelGlobalEntry 9 }
|
|
|
|
cnsClkSelGlobWtrTime OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the global
|
|
wait-to-restore time in the G.781
|
|
clock selection process."
|
|
REFERENCE "ITU-T standard G.781 section 5.9"
|
|
DEFVAL { 300 }
|
|
::= { cnsClkSelGlobalEntry 10 }
|
|
|
|
cnsClkSelGlobNofSources OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..255)
|
|
UNITS "clock sources"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the number of
|
|
synchronization sources currently
|
|
configured for the G.781
|
|
clock selection process."
|
|
::= { cnsClkSelGlobalEntry 11 }
|
|
|
|
cnsClkSelGlobLastHoldoverSeconds OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the duration of
|
|
the last holdover period in seconds.
|
|
If the holdover duration is less than a second,
|
|
the object will carry the value zero."
|
|
::= { cnsClkSelGlobalEntry 12 }
|
|
|
|
cnsClkSelGlobCurrHoldoverSeconds OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the duration of
|
|
the current holdover period.
|
|
If a system clock is in holdover mode,
|
|
the object carries the current holdover
|
|
duration in seconds. If the system clock
|
|
is not in holdover, the object carries
|
|
the value 0."
|
|
::= { cnsClkSelGlobalEntry 13 }
|
|
|
|
|
|
|
|
cnsSelectedInputSourceTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CnsSelectedInputSourceEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"T0 selected clock source table.
|
|
This table contains the selected clock source for the input T0
|
|
clock."
|
|
::= { ciscoNetsyncMIBTables 2 }
|
|
|
|
cnsSelectedInputSourceEntry OBJECT-TYPE
|
|
SYNTAX CnsSelectedInputSourceEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry is created in the table when the G.781 clock
|
|
selection process has successfully selected a T0 clock
|
|
source. The entry shall remain during the time
|
|
the G.781 clock selection process remains enabled."
|
|
INDEX { cnsSelInpSrcNetsyncIndex }
|
|
::= { cnsSelectedInputSourceTable 1 }
|
|
|
|
CnsSelectedInputSourceEntry ::= SEQUENCE {
|
|
cnsSelInpSrcNetsyncIndex Unsigned32,
|
|
cnsSelInpSrcName SnmpAdminString,
|
|
cnsSelInpSrcIntfType CiscoNetsyncIfType,
|
|
cnsSelInpSrcQualityLevel CiscoNetsyncQualityLevel,
|
|
cnsSelInpSrcPriority Unsigned32,
|
|
cnsSelInpSrcTimestamp TimeStamp,
|
|
cnsSelInpSrcFSW TruthValue,
|
|
cnsSelInpSrcMSW TruthValue
|
|
}
|
|
|
|
cnsSelInpSrcNetsyncIndex OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index that uniquely represents an entry in
|
|
this table. This index is assigned arbitrarily
|
|
by the clock selection process and may not be persistent
|
|
across reboots."
|
|
::= { cnsSelectedInputSourceEntry 1 }
|
|
|
|
cnsSelInpSrcName OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (1..255))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the name of the
|
|
selected T0 clock."
|
|
::= { cnsSelectedInputSourceEntry 2 }
|
|
|
|
cnsSelInpSrcIntfType OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncIfType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the type of the
|
|
selected T0 clock."
|
|
::= { cnsSelectedInputSourceEntry 3 }
|
|
|
|
cnsSelInpSrcQualityLevel OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the selected T0 clock
|
|
source's effective quality level, which
|
|
is the derived clock quality based on the three factors:
|
|
(a) Received quality level.
|
|
(b) Configured Rx quality level. This factor supersedes (a).
|
|
(c) System overridden quality level as a result of exceptional
|
|
events such as signal failure or ESMC failure. This factor
|
|
supersedes (a) and (b)."
|
|
::= { cnsSelectedInputSourceEntry 4 }
|
|
|
|
cnsSelInpSrcPriority OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..1024)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the configured
|
|
priority of the selected T0 clock.
|
|
A smaller value represents a higher priority."
|
|
REFERENCE "ITU-T standard G.781 section 5.10"
|
|
::= { cnsSelectedInputSourceEntry 5 }
|
|
|
|
cnsSelInpSrcTimestamp OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the timestamp of
|
|
the T0 clock source being selected by
|
|
the G.781 clock selection process."
|
|
::= { cnsSelectedInputSourceEntry 6 }
|
|
|
|
cnsSelInpSrcFSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the forced switching flag. Forced
|
|
switching, as described in G.781, is used to override the
|
|
currently selected synchronization source.
|
|
|
|
The 'true' value indicates the currently selected clock
|
|
source is a result of the forced switching. The 'false'
|
|
value indicates the currently selected clock source is
|
|
not a result of forced switching."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.2"
|
|
::= { cnsSelectedInputSourceEntry 7 }
|
|
|
|
cnsSelInpSrcMSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the manual switching flag.
|
|
The 'true' value indicates the currently selected clock source
|
|
is a result of the manual switch command. The command allows
|
|
a user to select a synchronization source assuming it is
|
|
enabled, not locked out, not in signal fail condition,
|
|
and has a QL better than DNU in QL-enabled mode. Furthermore,
|
|
in QL-enabled mode, a manual switch can be performed only to
|
|
a source which has the highest available QL."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.3"
|
|
::= { cnsSelectedInputSourceEntry 8 }
|
|
|
|
|
|
|
|
cnsInputSourceTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CnsInputSourceEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"T0 clock source table.
|
|
This table contains a list of input sources for input T0 clock
|
|
selection."
|
|
::= { ciscoNetsyncMIBTables 3 }
|
|
|
|
cnsInputSourceEntry OBJECT-TYPE
|
|
SYNTAX CnsInputSourceEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry is created in the table when a user adds a T0
|
|
clock source in the configuration. An entry is removed
|
|
in the table when a user removes a T0 clock source from
|
|
the configuration."
|
|
INDEX { cnsInpSrcNetsyncIndex }
|
|
::= { cnsInputSourceTable 1 }
|
|
|
|
CnsInputSourceEntry ::= SEQUENCE {
|
|
cnsInpSrcNetsyncIndex Unsigned32,
|
|
cnsInpSrcName SnmpAdminString,
|
|
cnsInpSrcIntfType CiscoNetsyncIfType,
|
|
cnsInpSrcPriority Unsigned32,
|
|
cnsInpSrcESMCCap CiscoNetsyncESMCCap,
|
|
cnsInpSrcSSMCap CiscoNetsyncSSMCap,
|
|
cnsInpSrcQualityLevelTxCfg CiscoNetsyncQualityLevel,
|
|
cnsInpSrcQualityLevelRxCfg CiscoNetsyncQualityLevel,
|
|
cnsInpSrcQualityLevelTx CiscoNetsyncQualityLevel,
|
|
cnsInpSrcQualityLevelRx CiscoNetsyncQualityLevel,
|
|
cnsInpSrcQualityLevel CiscoNetsyncQualityLevel,
|
|
cnsInpSrcHoldoffTime Unsigned32,
|
|
cnsInpSrcWtrTime Unsigned32,
|
|
cnsInpSrcLockout TruthValue,
|
|
cnsInpSrcSignalFailure TruthValue,
|
|
cnsInpSrcAlarm TruthValue,
|
|
cnsInpSrcAlarmInfo CiscoNetsyncAlarmInfo,
|
|
cnsInpSrcFSW TruthValue,
|
|
cnsInpSrcMSW TruthValue
|
|
}
|
|
|
|
cnsInpSrcNetsyncIndex OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index that uniquely represents an entry in
|
|
this table. This index is assigned arbitrarily
|
|
by the clock selection process and may not be persistent
|
|
across reboots."
|
|
::= { cnsInputSourceEntry 1 }
|
|
|
|
cnsInpSrcName OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (1..255))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the name of an input
|
|
clock source configured for the T0 clock
|
|
selection."
|
|
::= { cnsInputSourceEntry 2 }
|
|
|
|
cnsInpSrcIntfType OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncIfType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the type of an input
|
|
clock source configured for the T0 clock
|
|
selection."
|
|
::= { cnsInputSourceEntry 3 }
|
|
|
|
cnsInpSrcPriority OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..1024)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the priority of an input
|
|
clock source configured for the T0 clock
|
|
selection.
|
|
|
|
A smaller value represents a higher priority."
|
|
REFERENCE "ITU-T standard G.781 section 5.10"
|
|
::= { cnsInputSourceEntry 4 }
|
|
|
|
cnsInpSrcESMCCap OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncESMCCap
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the ESMC capability
|
|
of an input clock source configured for the
|
|
T0 clock selection. This is applicable only to Synchronous
|
|
Ethernet input clock source identified by cnsInpSrcIntfType
|
|
'netsyncIfTypeEthernet'."
|
|
::= { cnsInputSourceEntry 5 }
|
|
|
|
cnsInpSrcSSMCap OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncSSMCap
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the SSM capability
|
|
of an input clock source configured for the
|
|
T0 clock selection. This is applicable only to
|
|
any synchronous interface clock source except
|
|
SyncE interface, which is identified by cnsInpSrcIntfType
|
|
'netsyncIfTypeEthernet'."
|
|
::= { cnsInputSourceEntry 6 }
|
|
|
|
cnsInpSrcQualityLevelTxCfg OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the configured transmit
|
|
clock quality level of an input clock source."
|
|
::= { cnsInputSourceEntry 7 }
|
|
|
|
cnsInpSrcQualityLevelRxCfg OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the configured receive
|
|
clock quality level of an input clock source."
|
|
::= { cnsInputSourceEntry 8 }
|
|
|
|
cnsInpSrcQualityLevelTx OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the most recent clock
|
|
quality level transmitted on the input clock
|
|
source."
|
|
::= { cnsInputSourceEntry 9 }
|
|
|
|
cnsInpSrcQualityLevelRx OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the last clock quality
|
|
level received on the input clock source."
|
|
::= { cnsInputSourceEntry 10 }
|
|
|
|
cnsInpSrcQualityLevel OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the current clock quality
|
|
level of the input clock source. This is the
|
|
effective quality which is derived from three values:
|
|
|
|
1) most recent clock quality level received,
|
|
2) forced clock quality level (entered via configuration)
|
|
3) overridden clock quality level as a result of line protocol
|
|
down, signal failure, or alarms."
|
|
::= { cnsInputSourceEntry 11 }
|
|
|
|
cnsInpSrcHoldoffTime OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the hold-off time value of
|
|
an input clock source.
|
|
|
|
The hold-off time prevents short activation of signal failure
|
|
is passed to the selection process. When a signal failure
|
|
event is reported on a clock source, it waits the duration of
|
|
the hold-off time before declaring signal failure on the clock
|
|
source."
|
|
REFERENCE "ITU-T standard G.781 section 5.8"
|
|
::= { cnsInputSourceEntry 12 }
|
|
|
|
cnsInpSrcWtrTime OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
UNITS "Seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the wait-to-restore time value
|
|
of an input clock source.
|
|
|
|
The wait-to-restore time ensures that a previous failed
|
|
synchronization source is only again considered as available
|
|
by the selection process if it is fault-free for a certain time.
|
|
When a signal failure condition is cleared on a clock source,
|
|
it waits the duration of the wait-to-restore time before
|
|
clearing the signal failure status on the clock source."
|
|
REFERENCE "ITU-T standard G.781 section 5.9"
|
|
::= { cnsInputSourceEntry 13 }
|
|
|
|
cnsInpSrcLockout OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether or not the lockout
|
|
command has been applied to a clock source.
|
|
|
|
The 'true' value means the clock source is not
|
|
considered by the selection process."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.1"
|
|
::= { cnsInputSourceEntry 14 }
|
|
|
|
cnsInpSrcSignalFailure OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether or not a
|
|
signal failure event is currently being
|
|
reported on the input clock source."
|
|
REFERENCE "ITU-T standard G.781 section 5.7"
|
|
::= { cnsInputSourceEntry 15 }
|
|
|
|
cnsInpSrcAlarm OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether or not an
|
|
alarm event is currently being reported
|
|
on the input clock source."
|
|
::= { cnsInputSourceEntry 16 }
|
|
|
|
cnsInpSrcAlarmInfo OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncAlarmInfo
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the alarm reasons of
|
|
an input clock source if an alarm event
|
|
is being reported on it."
|
|
::= { cnsInputSourceEntry 17 }
|
|
|
|
cnsInpSrcFSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the forced switching flag.
|
|
Forced switching, as described in G.781, is used to
|
|
override the currently selected synchronization source.
|
|
|
|
The 'true' value indicates the currently selected clock source
|
|
is a result of the forced switching. The 'false' value
|
|
indicates the currently selected clock source is not a result
|
|
of forced switching."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.2"
|
|
::= { cnsInputSourceEntry 18 }
|
|
|
|
cnsInpSrcMSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the manual switching flag.
|
|
|
|
The 'true' value indicates the currently selected clock source
|
|
is a result of the manual switching. The switch allows
|
|
a user to select a synchronization source assuming it is
|
|
enabled, not locked out, not in signal fail condition,
|
|
and has a QL better than DNU in QL-enabled mode.
|
|
|
|
A clock source is enabled when it occupies a row in
|
|
cnsInputSourceTable. A clock source is not locked out
|
|
when cnsInpSrcLockout contains the value 'false'.
|
|
A clock source is not in signal failure condition when
|
|
cnsInpSrcSignalFailure contains the value 'false'.
|
|
The QL is identified in cnsInpSrcQualityLevel.
|
|
|
|
In QL-enabled mode, a manual switch can be performed only to
|
|
a source which has the highest available QL."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.3"
|
|
::= { cnsInputSourceEntry 19 }
|
|
|
|
|
|
|
|
cnsExtOutputTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CnsExtOutputEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"T4 external output table.
|
|
This table contains a list of T4 external outputs.
|
|
|
|
Each T4 external output is associated with clock
|
|
source(s) to be found in cnsT4ClockSourceTable.
|
|
The clock selection process considers all the
|
|
available clock sources and select the T4 clock
|
|
source based on the G.781 clock selection algorithm."
|
|
::= { ciscoNetsyncMIBTables 4 }
|
|
|
|
cnsExtOutputEntry OBJECT-TYPE
|
|
SYNTAX CnsExtOutputEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry is created in the table when a user adds
|
|
a T4 external output in the configuration. A T4 external
|
|
output configured input clock sources are defined in
|
|
cnsT4ClockSourceTable.
|
|
|
|
An entry is removed from the table when a user removes
|
|
a T4 external output from the configuration."
|
|
INDEX { cnsExtOutListIndex }
|
|
::= { cnsExtOutputTable 1 }
|
|
|
|
CnsExtOutputEntry ::= SEQUENCE {
|
|
cnsExtOutListIndex Unsigned32,
|
|
cnsExtOutSelNetsyncIndex Unsigned32,
|
|
cnsExtOutName SnmpAdminString,
|
|
cnsExtOutIntfType CiscoNetsyncIfType,
|
|
cnsExtOutQualityLevel CiscoNetsyncQualityLevel,
|
|
cnsExtOutPriority Unsigned32,
|
|
cnsExtOutFSW TruthValue,
|
|
cnsExtOutMSW TruthValue,
|
|
cnsExtOutSquelch TruthValue
|
|
}
|
|
|
|
cnsExtOutListIndex OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index that uniquely represents an entry in
|
|
this table. This index is assigned arbitrarily by the
|
|
clock selection process and may not be persistent
|
|
across reboots."
|
|
::= { cnsExtOutputEntry 1 }
|
|
|
|
cnsExtOutSelNetsyncIndex OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index that uniquely represents the selected input clock
|
|
source whose information is reported by a row in
|
|
cnsT4ClockSourceTable. The index lists the value of
|
|
cnsT4ClkSrcNetsyncIndex, which is the input clock source
|
|
of the T4 external output selected by the G.781 clock
|
|
selection process."
|
|
::= { cnsExtOutputEntry 2 }
|
|
|
|
cnsExtOutName OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (1..255))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the name of a
|
|
T4 external output."
|
|
::= { cnsExtOutputEntry 3 }
|
|
|
|
cnsExtOutIntfType OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncIfType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the interface type
|
|
of the T4 external output."
|
|
::= { cnsExtOutputEntry 4 }
|
|
|
|
cnsExtOutQualityLevel OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the clock quality
|
|
of the T4 external output."
|
|
::= { cnsExtOutputEntry 5 }
|
|
|
|
cnsExtOutPriority OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..1024)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the priority of the
|
|
selected clock source for a T4 external
|
|
output.
|
|
|
|
A smaller value represents a higher priority."
|
|
REFERENCE "ITU-T standard G.781 section 5.10"
|
|
::= { cnsExtOutputEntry 6 }
|
|
|
|
cnsExtOutFSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the forced switching flag.
|
|
Forced switching, as described in G.781, is used to
|
|
override the currently selected synchronization source,
|
|
The T4 selected synchronization source is identified by
|
|
cnsExtOutSelNetsyncIndex, which contains the index to
|
|
the clock source in cnsT4ClockSourceTable.
|
|
|
|
The 'true' value indicates the currently selected
|
|
T4 clock source is a result of the forced switching.
|
|
The 'false' value indicates the currently selected T4
|
|
clock source is not a result of forced switching."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.2"
|
|
::= { cnsExtOutputEntry 7 }
|
|
|
|
cnsExtOutMSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the manual switching flag.
|
|
|
|
The 'true' value indicates the currently selected
|
|
T4 clock source is a result of the manual switch command.
|
|
The command allows a user to select a synchronization source
|
|
assuming it is enabled, not locked out, not in signal fail
|
|
condition, and has a QL better than DNU in QL-enabled mode.
|
|
|
|
A clock source is enabled when it occupies in row in
|
|
cnsT4ClockSourceTable. A clock source is not locked out
|
|
when cnsT4ClkSrcLockout contains the value 'false'.
|
|
A clock source is not in signal failure condition when
|
|
cnsT4ClkSrcSignalFailure contains the value 'false'.
|
|
The QL is identified in cnsT4ClkSrcQualityLevel.
|
|
|
|
In QL-enabled mode, a manual switch can be
|
|
performed only to a source which has the highest
|
|
available QL."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.3"
|
|
::= { cnsExtOutputEntry 8 }
|
|
|
|
cnsExtOutSquelch OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether or not a
|
|
T4 external output is squelched.
|
|
|
|
Squelching is a sychronization function defined to prevent
|
|
transmission of a timing signal with a quality that is lower
|
|
than the quality of the clock in the receiving networks
|
|
element or SASE. It is also used for the prevention of
|
|
timing loops."
|
|
REFERENCE "ITU-T standard G.781 section 5.4.1.4"
|
|
::= { cnsExtOutputEntry 9 }
|
|
|
|
|
|
|
|
cnsT4ClockSourceTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CnsT4ClockSourceEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"T4 clock source table.
|
|
This table contains a list of input sources for a specific
|
|
T4 external output. An entry shall be added to
|
|
cnsExtOutputTable first. Then clock sources shall be
|
|
added in this table for the selection process to select
|
|
the appropriate T4 clock source."
|
|
::= { ciscoNetsyncMIBTables 5 }
|
|
|
|
cnsT4ClockSourceEntry OBJECT-TYPE
|
|
SYNTAX CnsT4ClockSourceEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry is created in the table when a user adds a
|
|
clock source to a T4 external output in the configuration.
|
|
The T4 external output is defined in the T4 external
|
|
output table. An entry is removed in the table when a user
|
|
removes a T4 clock source from the configuration."
|
|
INDEX {
|
|
cnsExtOutListIndex,
|
|
cnsT4ClkSrcNetsyncIndex
|
|
}
|
|
::= { cnsT4ClockSourceTable 1 }
|
|
|
|
CnsT4ClockSourceEntry ::= SEQUENCE {
|
|
cnsT4ClkSrcNetsyncIndex Unsigned32,
|
|
cnsT4ClkSrcName SnmpAdminString,
|
|
cnsT4ClkSrcIntfType CiscoNetsyncIfType,
|
|
cnsT4ClkSrcPriority Unsigned32,
|
|
cnsT4ClkSrcESMCCap CiscoNetsyncESMCCap,
|
|
cnsT4ClkSrcSSMCap CiscoNetsyncSSMCap,
|
|
cnsT4ClkSrcQualityLevelTxCfg CiscoNetsyncQualityLevel,
|
|
cnsT4ClkSrcQualityLevelRxCfg CiscoNetsyncQualityLevel,
|
|
cnsT4ClkSrcQualityLevelTx CiscoNetsyncQualityLevel,
|
|
cnsT4ClkSrcQualityLevelRx CiscoNetsyncQualityLevel,
|
|
cnsT4ClkSrcQualityLevel CiscoNetsyncQualityLevel,
|
|
cnsT4ClkSrcHoldoffTime Unsigned32,
|
|
cnsT4ClkSrcWtrTime Unsigned32,
|
|
cnsT4ClkSrcLockout TruthValue,
|
|
cnsT4ClkSrcSignalFailure TruthValue,
|
|
cnsT4ClkSrcAlarm TruthValue,
|
|
cnsT4ClkSrcAlarmInfo CiscoNetsyncAlarmInfo,
|
|
cnsT4ClkSrcFSW TruthValue,
|
|
cnsT4ClkSrcMSW TruthValue
|
|
}
|
|
|
|
cnsT4ClkSrcNetsyncIndex OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..4294967295)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An index that uniquely represents an entry in
|
|
this table. This index is assigned arbitrarily by the
|
|
clock selection process and may not be persistent
|
|
across reboots."
|
|
::= { cnsT4ClockSourceEntry 1 }
|
|
|
|
cnsT4ClkSrcName OBJECT-TYPE
|
|
SYNTAX SnmpAdminString (SIZE (1..255))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the name of a input
|
|
clock source configured for the T4 clock
|
|
selection."
|
|
::= { cnsT4ClockSourceEntry 2 }
|
|
|
|
cnsT4ClkSrcIntfType OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncIfType
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the type of an input
|
|
clock source configured for the T4 clock
|
|
selection."
|
|
::= { cnsT4ClockSourceEntry 3 }
|
|
|
|
cnsT4ClkSrcPriority OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..1024)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the priority of an input
|
|
clock source configured for the T4 clock
|
|
selection.
|
|
|
|
A smaller value represents a higher priority."
|
|
REFERENCE "ITU-T standard G.781 section 5.10"
|
|
::= { cnsT4ClockSourceEntry 4 }
|
|
|
|
cnsT4ClkSrcESMCCap OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncESMCCap
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the ESMC capability
|
|
of an input clock source configured for the
|
|
T4 clock selection. This is applicable
|
|
only to Synchronous Ethernet input clock source
|
|
identified by cnsT4ClkSrcIntfType 'netsyncIfTypeEthernet'."
|
|
::= { cnsT4ClockSourceEntry 5 }
|
|
|
|
cnsT4ClkSrcSSMCap OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncSSMCap
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the SSM capability
|
|
of an input clock source configured for the
|
|
T4 clock selection. This is applicable only to any
|
|
synchronous interface clock source except SyncE interface,
|
|
which is identified by cnsT4ClkSrcIntfType
|
|
'netsyncIfTypeEthernet'."
|
|
::= { cnsT4ClockSourceEntry 6 }
|
|
|
|
cnsT4ClkSrcQualityLevelTxCfg OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the configured transmit
|
|
clock quality level of a T4 input clock source."
|
|
::= { cnsT4ClockSourceEntry 7 }
|
|
|
|
cnsT4ClkSrcQualityLevelRxCfg OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the configured receive
|
|
clock quality level of a T4 input clock source."
|
|
::= { cnsT4ClockSourceEntry 8 }
|
|
|
|
cnsT4ClkSrcQualityLevelTx OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the most recent clock
|
|
quality level transmitted on the T4 input
|
|
clock source."
|
|
::= { cnsT4ClockSourceEntry 9 }
|
|
|
|
cnsT4ClkSrcQualityLevelRx OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the last clock quality
|
|
level received on the T4 input clock
|
|
source."
|
|
::= { cnsT4ClockSourceEntry 10 }
|
|
|
|
cnsT4ClkSrcQualityLevel OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncQualityLevel
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the current clock quality
|
|
level of the T4 input clock source. This is the
|
|
effective quality which is derived from three values:
|
|
|
|
1) most recent clock quality level received,
|
|
2) forced clock quality level (entered via configuration)
|
|
3) overridden clock quality level as a result of line protocol
|
|
down, signal failure, or alarms."
|
|
::= { cnsT4ClockSourceEntry 11 }
|
|
|
|
cnsT4ClkSrcHoldoffTime OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the hold-off time value of
|
|
a T4 input clock source.
|
|
|
|
The hold-off time prevents short activation of signal failure
|
|
is passed to the selection process. When a signal failure
|
|
event is reported on a clock source, it waits the duration of
|
|
the hold-off time before declaring signal failure on the clock
|
|
source."
|
|
REFERENCE "ITU-T standard G.781 section 5.8"
|
|
::= { cnsT4ClockSourceEntry 12 }
|
|
|
|
cnsT4ClkSrcWtrTime OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the wait-to-restore time value
|
|
of a T4 input clock source.
|
|
|
|
The wait-to-restore time ensures that a previous failed
|
|
synchronization source is only again considered as available
|
|
by the selection process if it is fault-free for a certain time.
|
|
When a signal failure condition is cleared on a clock source,
|
|
it waits the duration of the wait-to-restore time before
|
|
clearing the signal failure status on the clock source."
|
|
REFERENCE "ITU-T standard G.781 section 5.9"
|
|
::= { cnsT4ClockSourceEntry 13 }
|
|
|
|
cnsT4ClkSrcLockout OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether or not the lockout
|
|
command has been applied on a T4 clock source.
|
|
|
|
The 'true' value means the clock source is not
|
|
considered by the selection process."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.1"
|
|
::= { cnsT4ClockSourceEntry 14 }
|
|
|
|
cnsT4ClkSrcSignalFailure OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether or not a
|
|
signal failure event is currently being
|
|
reported on the T4 input clock source."
|
|
REFERENCE "ITU-T standard G.781 section 5.7"
|
|
::= { cnsT4ClockSourceEntry 15 }
|
|
|
|
cnsT4ClkSrcAlarm OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates whether or not an
|
|
alarm event is currently being reported
|
|
on the T4 input clock source."
|
|
::= { cnsT4ClockSourceEntry 16 }
|
|
|
|
cnsT4ClkSrcAlarmInfo OBJECT-TYPE
|
|
SYNTAX CiscoNetsyncAlarmInfo
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the alarm reasons of
|
|
a T4 input clock source if an alarm event
|
|
is being reported on the clock source."
|
|
::= { cnsT4ClockSourceEntry 17 }
|
|
|
|
cnsT4ClkSrcFSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the forced switching flag.
|
|
Forced switching, as described in G.781, is used to
|
|
override the currently selected synchronization source.
|
|
|
|
The 'true' value indicates the currently selected
|
|
T4 clock source is a result of the forced switching.
|
|
The 'false' value indicates the currently selected
|
|
T4 clock source is not a result of forced switching."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.2"
|
|
::= { cnsT4ClockSourceEntry 18 }
|
|
|
|
cnsT4ClkSrcMSW OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the manual switching flag.
|
|
|
|
The 'true' value indicates the currently selected
|
|
T4 clock source is a result of the manual switching.
|
|
The switch allows a user to select a
|
|
synchronization source assuming it is enabled,
|
|
not locked out, not in signal fail condition,
|
|
and has a QL better than DNU in QL-enabled mode.
|
|
|
|
A clock source is enabled when it occupies a row in
|
|
cnsT4ClockSourceTable. A clock source is not locked
|
|
out when cnsT4ClkSrcLockout contains the value 'false'.
|
|
A clock source is not in signal failure condition when
|
|
cnsT4ClkSrcSignalFailure contains the value 'false'.
|
|
The QL is identified in cnsT4ClkSrcQualityLevel.
|
|
|
|
In QL-enabled mode, a manual switch
|
|
can be performed only to a source which has the
|
|
highest available QL."
|
|
REFERENCE "ITU-T standard G.781 section 5.11.2.3"
|
|
::= { cnsT4ClockSourceEntry 19 }
|
|
|
|
cnsNotifObjects OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIBObjects 2 }
|
|
|
|
|
|
cnsInpSrcFailClear OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the clear status of a signal failure
|
|
event. A value of 'true' means a signal failure event reported
|
|
on a clock source has been cleared. A value of 'false' means
|
|
a signal event has been reported on a clock source."
|
|
::= { cnsNotifObjects 1 }
|
|
|
|
cnsInpSrcAlarmClear OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the clear status of an alarm event.
|
|
A value of 'true' means an alarm event reported on a clock
|
|
source has been cleared. A value of 'false' means an alarm
|
|
event has been reported on a clock source."
|
|
::= { cnsNotifObjects 2 }
|
|
|
|
ciscoNetsyncMIBNotifControl OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIBObjects 3 }
|
|
|
|
cnsMIBEnableStatusNotification OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A control object to enable/disable
|
|
ciscoNetsyncSelectedT0Clock, ciscoNetsyncSelectedT4Clock,
|
|
ciscoNetsyncInputSignalFailureStatus,
|
|
ciscoNetsyncInputAlarmStatus notifications at the system
|
|
level.
|
|
This object should hold any of the below values.
|
|
true - The notif is enabled globally for the system
|
|
false- The notif is disabled globally for the system"
|
|
DEFVAL { false }
|
|
::= { ciscoNetsyncMIBNotifControl 1 }
|
|
|
|
|
|
-- Default Notification Type
|
|
|
|
ciscoNetsyncSelectedT0Clock NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
cnsSelInpSrcName,
|
|
cnsSelInpSrcIntfType,
|
|
cnsSelInpSrcQualityLevel,
|
|
cnsSelInpSrcPriority
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"T0 clock selection notification.
|
|
|
|
This notification is generated when one
|
|
of the following conditions is met:
|
|
|
|
- A new clock source is selected by the
|
|
T0 clock selection.
|
|
- The clock quality of a T0 selected clock
|
|
source is changed.
|
|
- The configured priority of a T0 selected
|
|
clock source is changed.
|
|
"
|
|
::= { ciscoNetsyncMIBNotifs 1 }
|
|
|
|
ciscoNetsyncSelectedT4Clock NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
cnsExtOutName,
|
|
cnsT4ClkSrcName,
|
|
cnsT4ClkSrcIntfType,
|
|
cnsT4ClkSrcQualityLevel,
|
|
cnsT4ClkSrcPriority
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"T4 clock selection notification.
|
|
|
|
This notification is generated when one
|
|
of the following conditions is met:
|
|
|
|
- A new clock source is selected by the
|
|
T4 clock selection.
|
|
- The clock quality of a T4 selected clock
|
|
source is changed.
|
|
- The configured priority of a T4 selected
|
|
clock source is changed.
|
|
"
|
|
::= { ciscoNetsyncMIBNotifs 2 }
|
|
|
|
ciscoNetsyncInputSignalFailureStatus NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
cnsInpSrcName,
|
|
cnsInpSrcIntfType,
|
|
cnsInpSrcFailClear
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Input clock source signal failure notification.
|
|
|
|
This notification is generated when a signal
|
|
failure event is reported on an input clock source.
|
|
One of the conditions a signal failure event
|
|
could be due to interface shutdown."
|
|
::= { ciscoNetsyncMIBNotifs 3 }
|
|
|
|
ciscoNetsyncInputAlarmStatus NOTIFICATION-TYPE
|
|
OBJECTS {
|
|
cnsInpSrcName,
|
|
cnsInpSrcIntfType,
|
|
cnsInpSrcAlarmInfo,
|
|
cnsInpSrcAlarmClear
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Input clock source alarm notification.
|
|
|
|
This notification is generated when an alarm
|
|
event is reported on an input clock source."
|
|
::= { ciscoNetsyncMIBNotifs 4 }
|
|
|
|
|
|
ciscoNetsyncMIBCompliances OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIBConform 1 }
|
|
|
|
ciscoNetsyncMIBGroups OBJECT IDENTIFIER
|
|
::= { ciscoNetsyncMIBConform 2 }
|
|
|
|
|
|
ciscoNetsyncMIBCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This is a default module-compliance
|
|
containing default object groups."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
cnsClkSelGlobalObjectGroup,
|
|
cnsSelectedInputSourceObjectGroup,
|
|
cnsInputSourceObjectGroup,
|
|
cnsExtOutputObjectGroup,
|
|
cnsT4ClkSrcObjectGroup,
|
|
ciscoNetsyncMIBNotificationGroup,
|
|
cnsMIBNotifEnablesGroup
|
|
}
|
|
::= { ciscoNetsyncMIBCompliances 1 }
|
|
|
|
-- Units of Conformance
|
|
|
|
cnsClkSelGlobalObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnsClkSelGlobProcessMode,
|
|
cnsClkSelGlobClockMode,
|
|
cnsClkSelGlobNetsyncEnable,
|
|
cnsClkSelGlobRevertiveMode,
|
|
cnsClkSelGlobESMCMode,
|
|
cnsClkSelGlobEECOption,
|
|
cnsClkSelGlobNetworkOption,
|
|
cnsClkSelGlobHoldoffTime,
|
|
cnsClkSelGlobWtrTime,
|
|
cnsClkSelGlobNofSources,
|
|
cnsClkSelGlobLastHoldoverSeconds,
|
|
cnsClkSelGlobCurrHoldoverSeconds
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains all objects referenced by
|
|
the G.781 clock selection process table."
|
|
::= { ciscoNetsyncMIBGroups 1 }
|
|
|
|
cnsSelectedInputSourceObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnsSelInpSrcName,
|
|
cnsSelInpSrcQualityLevel,
|
|
cnsSelInpSrcTimestamp,
|
|
cnsSelInpSrcFSW,
|
|
cnsSelInpSrcMSW,
|
|
cnsSelInpSrcIntfType,
|
|
cnsSelInpSrcPriority
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains all objects referenced by
|
|
cnsSelectedInputSourceTable."
|
|
::= { ciscoNetsyncMIBGroups 2 }
|
|
|
|
cnsInputSourceObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnsInpSrcName,
|
|
cnsInpSrcIntfType,
|
|
cnsInpSrcPriority,
|
|
cnsInpSrcESMCCap,
|
|
cnsInpSrcSSMCap,
|
|
cnsInpSrcQualityLevelTxCfg,
|
|
cnsInpSrcQualityLevelRxCfg,
|
|
cnsInpSrcQualityLevelTx,
|
|
cnsInpSrcQualityLevelRx,
|
|
cnsInpSrcQualityLevel,
|
|
cnsInpSrcHoldoffTime,
|
|
cnsInpSrcWtrTime,
|
|
cnsInpSrcLockout,
|
|
cnsInpSrcSignalFailure,
|
|
cnsInpSrcAlarm,
|
|
cnsInpSrcAlarmInfo,
|
|
cnsInpSrcFSW,
|
|
cnsInpSrcMSW,
|
|
cnsInpSrcAlarmClear,
|
|
cnsInpSrcFailClear
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains all objects referenced by
|
|
cnsInputSourceTable."
|
|
::= { ciscoNetsyncMIBGroups 3 }
|
|
|
|
cnsExtOutputObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnsExtOutName,
|
|
cnsExtOutSelNetsyncIndex,
|
|
cnsExtOutIntfType,
|
|
cnsExtOutQualityLevel,
|
|
cnsExtOutPriority,
|
|
cnsExtOutFSW,
|
|
cnsExtOutMSW,
|
|
cnsExtOutSquelch
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains all objects referenced by
|
|
cnsExtOutputTable."
|
|
::= { ciscoNetsyncMIBGroups 4 }
|
|
|
|
cnsT4ClkSrcObjectGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnsT4ClkSrcName,
|
|
cnsT4ClkSrcIntfType,
|
|
cnsT4ClkSrcPriority,
|
|
cnsT4ClkSrcESMCCap,
|
|
cnsT4ClkSrcSSMCap,
|
|
cnsT4ClkSrcQualityLevelTxCfg,
|
|
cnsT4ClkSrcQualityLevelRxCfg,
|
|
cnsT4ClkSrcQualityLevelTx,
|
|
cnsT4ClkSrcQualityLevelRx,
|
|
cnsT4ClkSrcQualityLevel,
|
|
cnsT4ClkSrcHoldoffTime,
|
|
cnsT4ClkSrcWtrTime,
|
|
cnsT4ClkSrcLockout,
|
|
cnsT4ClkSrcSignalFailure,
|
|
cnsT4ClkSrcAlarm,
|
|
cnsT4ClkSrcAlarmInfo,
|
|
cnsT4ClkSrcFSW,
|
|
cnsT4ClkSrcMSW
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains all objects referenced by
|
|
cnsT4ClockSourceTable."
|
|
::= { ciscoNetsyncMIBGroups 5 }
|
|
|
|
cnsMIBNotifEnablesGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnsMIBEnableStatusNotification
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The collection of objects which are used to
|
|
enable notification.
|
|
"
|
|
::= { ciscoNetsyncMIBGroups 6 }
|
|
|
|
ciscoNetsyncMIBNotificationGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS {
|
|
ciscoNetsyncSelectedT0Clock,
|
|
ciscoNetsyncSelectedT4Clock,
|
|
ciscoNetsyncInputSignalFailureStatus,
|
|
ciscoNetsyncInputAlarmStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The is the netsync notification group."
|
|
::= { ciscoNetsyncMIBGroups 7 }
|
|
|
|
|
|
END
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|