971 lines
33 KiB
Plaintext
971 lines
33 KiB
Plaintext
-- *******************************************************************
|
|
-- CISCO-LWAPP-DOT11-CLIENT-CALIB-MIB.my
|
|
-- Dot11 Wireless Clients Calibration MIB
|
|
--
|
|
-- December 2005, Devesh Pujari, Prasanna Viswakumar
|
|
--
|
|
-- Copyright (c) 2005-2006, 2011 by Cisco Systems Inc.
|
|
-- All rights reserved.
|
|
-- *******************************************************************
|
|
|
|
CISCO-LWAPP-DOT11-CLIENT-CALIB-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE,
|
|
Unsigned32,
|
|
Integer32
|
|
FROM SNMPv2-SMI
|
|
MODULE-COMPLIANCE,
|
|
OBJECT-GROUP
|
|
FROM SNMPv2-CONF
|
|
TimeStamp,
|
|
MacAddress,
|
|
TimeInterval,
|
|
TruthValue,
|
|
RowStatus,
|
|
StorageType
|
|
FROM SNMPv2-TC
|
|
cLApSysMacAddress,
|
|
cLApDot11IfSlotId
|
|
FROM CISCO-LWAPP-AP-MIB
|
|
ciscoMgmt
|
|
FROM CISCO-SMI;
|
|
|
|
|
|
-- ********************************************************************
|
|
-- * MODULE IDENTITY
|
|
-- ********************************************************************
|
|
|
|
ciscoLwappDot11ClientCalibMIB MODULE-IDENTITY
|
|
LAST-UPDATED "201904090000Z"
|
|
ORGANIZATION "Cisco Systems Inc."
|
|
CONTACT-INFO
|
|
"Cisco Systems,
|
|
Customer Service
|
|
Postal: 170 West Tasman Drive
|
|
San Jose, CA 95134
|
|
USA
|
|
Tel: +1 800 553-NETS
|
|
|
|
Email: cs-wnbu-snmp@cisco.com"
|
|
DESCRIPTION
|
|
"This MIB is intended to be implemented on all those
|
|
devices operating as Central controllers, that
|
|
terminate the Light Weight Access Point Protocol
|
|
tunnel from Cisco Light-weight LWAPP Access Points.
|
|
|
|
Information provided by this MIB is about the
|
|
configuration and monitoring of 802.11 wireless
|
|
clients in the network.
|
|
|
|
The relationship between CC and the LWAPP APs
|
|
can be depicted as follows:
|
|
|
|
+......+ +......+ +......+ +......+
|
|
+ + + + + + + +
|
|
+ CC + + CC + + CC + + CC +
|
|
+ + + + + + + +
|
|
+......+ +......+ +......+ +......+
|
|
.. . . .
|
|
.. . . .
|
|
. . . . .
|
|
. . . . .
|
|
. . . . .
|
|
. . . . .
|
|
+......+ +......+ +......+ +......+ +......+
|
|
+ + + + + + + + + +
|
|
+ AP + + AP + + AP + + AP + + AP +
|
|
+ + + + + + + + + +
|
|
+......+ +......+ +......+ +......+ +......+
|
|
. . . .
|
|
. . . . .
|
|
. . . . .
|
|
. . . . .
|
|
. . . . .
|
|
+......+ +......+ +......+ +......+ +......+
|
|
+ + + + + + + + + +
|
|
+ MN + + MN + + MN + + MN + + MN +
|
|
+ + + + + + + + + +
|
|
+......+ +......+ +......+ +......+ +......+
|
|
|
|
The LWAPP tunnel exists between the controller and
|
|
the APs. The MNs communicate with the APs through
|
|
the protocol defined by the 802.11 standard.
|
|
|
|
LWAPP APs, upon bootup, discover and join one of the
|
|
controllers and the controller pushes the configuration,
|
|
that includes the WLAN parameters, to the LWAPP APs.
|
|
The APs then encapsulate all the 802.11 frames from
|
|
wireless clients inside LWAPP frames and forward
|
|
the LWAPP frames to the controller.
|
|
|
|
GLOSSARY
|
|
|
|
Access Point ( AP )
|
|
-------------------
|
|
|
|
An entity that contains an 802.11 medium access
|
|
control ( MAC ) and physical layer ( PHY ) interface
|
|
and provides access to the distribution services via
|
|
the wireless medium for associated clients.
|
|
|
|
LWAPP APs encapsulate all the 802.11 frames in
|
|
LWAPP frames and sends them to the controller to which
|
|
it is logically connected.
|
|
|
|
Light Weight Access Point Protocol ( LWAPP )
|
|
--------------------------------------------
|
|
|
|
This is a generic protocol that defines the
|
|
communication between the Access Points and the
|
|
Central Controller.
|
|
|
|
Mobile Node ( MN )
|
|
------------------
|
|
|
|
A roaming 802.11 wireless device in a wireless
|
|
network associated with an access point. Mobile Node,
|
|
Mobile Station(Ms) and client are used
|
|
interchangeably.
|
|
|
|
Signal to Noise Ratio ( SNR )
|
|
-----------------------------
|
|
|
|
It is a measure used in science and engineering
|
|
that compares the level of a desired signal to
|
|
the level of background noise. It is defined as
|
|
the ratio of signal power to the noise power.
|
|
A ratio higher than 1:1 indicates more signal than
|
|
noise. While SNR is commonly quoted for electrical
|
|
signals, it can be applied to any form of signal.
|
|
|
|
Received Signal Strength Indicator ( RSSI )
|
|
-------------------------------------------
|
|
|
|
It is a measurement of the power present in a
|
|
received radio signal.
|
|
|
|
Radio Frequency Identification ( RFID )
|
|
-------------------------------------------
|
|
|
|
It is a technology that uses radio waves to transfer data
|
|
from an electronic tag, called RFID tag or label, attached
|
|
to an object, through a reader for the purpose of identifying
|
|
and tracking the object.
|
|
|
|
REFERENCE
|
|
|
|
[1] Wireless LAN Medium Access Control ( MAC ) and
|
|
Physical Layer ( PHY ) Specifications
|
|
|
|
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
|
|
Weight Access Point Protocol"
|
|
REVISION "201904090000Z"
|
|
DESCRIPTION
|
|
"Added Following scalar objects
|
|
- cLD11RfidRssiExpiryTime
|
|
- cLD11RfidRssiHalflifeTime
|
|
- cLD11RfidNotifyThresholdTime
|
|
- cLD11RfidDataEnable
|
|
- cLD11RfidTimeout"
|
|
REVISION "201111250000Z"
|
|
DESCRIPTION
|
|
"Added following OBJECT-GROUP:
|
|
- cLD11ClientCalibClientConfigGroup
|
|
- cLD11ClientCalibGlobalConfigGroup
|
|
- cLD11ClientCalibRssiDataSampleGroup
|
|
Depreated following OBJECT-GROUP:
|
|
- ciscoLwappDot11ClientCalibMIBConfigGroup
|
|
Added new compliance:
|
|
- ciscoLwappDot11ClientCalibMIBComplianceRev1"
|
|
REVISION "200702120000Z"
|
|
DESCRIPTION
|
|
"Added ciscoLwappDot11ClientCalibMIBConfigGroupSup1
|
|
OBJECT-GROUP."
|
|
REVISION "200604110000Z"
|
|
DESCRIPTION
|
|
"Initial version of this MIB module."
|
|
::= { ciscoMgmt 522 }
|
|
|
|
|
|
ciscoLwappDot11ClientCalibMIBNotifs OBJECT IDENTIFIER
|
|
::= { ciscoLwappDot11ClientCalibMIB 0 }
|
|
|
|
ciscoLwappDot11ClientCalibMIBObjects OBJECT IDENTIFIER
|
|
::= { ciscoLwappDot11ClientCalibMIB 1 }
|
|
|
|
ciscoLwappDot11ClientCalibMIBConform OBJECT IDENTIFIER
|
|
::= { ciscoLwappDot11ClientCalibMIB 2 }
|
|
|
|
cldccConfig OBJECT IDENTIFIER
|
|
::= { ciscoLwappDot11ClientCalibMIBObjects 1 }
|
|
|
|
cldccStatus OBJECT IDENTIFIER
|
|
::= { ciscoLwappDot11ClientCalibMIBObjects 2 }
|
|
|
|
cldccRssiSamples OBJECT IDENTIFIER
|
|
::= { cldccStatus 1 }
|
|
|
|
-- ********************************************************************
|
|
-- Wireless Client Calibration
|
|
-- ********************************************************************
|
|
|
|
cLD11ClientCalibTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CLD11ClientCalibEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table represents the calibration for the
|
|
802.11 wireless clients that would associate
|
|
to the APs that have joined this controller.
|
|
|
|
An entry is created through an explicit management
|
|
action initiated by the administrator through a
|
|
network management station by specifying the
|
|
calibration parameters for a particular client
|
|
identified by cLD11ClientCalibMacAddress and setting
|
|
the RowStatus object to 'createAndGo'. An existing
|
|
entry is deleted by setting the RowStatus object to
|
|
'destroy'. The object cLD11ClientCalibTableMaxEntries
|
|
represents the maximum number of entries in this
|
|
table."
|
|
::= { cldccConfig 1 }
|
|
|
|
cLD11ClientCalibEntry OBJECT-TYPE
|
|
SYNTAX CLD11ClientCalibEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry represents a conceptual row in this
|
|
table and provides the information about the
|
|
calibration parameters for wireless clients."
|
|
INDEX { cLD11ClientCalibMacAddress }
|
|
::= { cLD11ClientCalibTable 1 }
|
|
|
|
CLD11ClientCalibEntry ::= SEQUENCE {
|
|
cLD11ClientCalibMacAddress MacAddress,
|
|
cLD11ClientCalibBeaconInterval TimeInterval,
|
|
cLD11ClientCalibRowStatus RowStatus,
|
|
cLD11ClientCalibNumberOfRadios Unsigned32,
|
|
cLD11ClientCalibNumberOfSamples Unsigned32,
|
|
cLD11ClientCalibSamplesCollected Unsigned32,
|
|
cLD11ClientCalibBeaconIntervalExt TimeInterval,
|
|
cLD11ClientCalibStorageType StorageType
|
|
}
|
|
|
|
cLD11ClientCalibMacAddress OBJECT-TYPE
|
|
SYNTAX MacAddress
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the MAC address of the
|
|
802.11 wireless client for which the
|
|
calibration parameters in this entry are
|
|
applicable and uniquely identifies this entry."
|
|
::= { cLD11ClientCalibEntry 1 }
|
|
|
|
cLD11ClientCalibBeaconInterval OBJECT-TYPE
|
|
SYNTAX TimeInterval (400..3240000)
|
|
UNITS "hundredths-seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This object specifies the time interval, expressed
|
|
here in hundredths of a second at which an AP
|
|
issues radio measurement request messages to a
|
|
client for every SSID. It is not recommended to
|
|
configure values less than 10 seconds (1000).
|
|
The value configured through this object is
|
|
reflected in the operation of the LWAPP APs only if
|
|
cLD11ClientCalibBeaconEnabled is set to 'true'.
|
|
|
|
This object has been deprecated and is replaced by the
|
|
object cLD11ClientCalibBeaconIntervalExt."
|
|
DEFVAL { 60000 }
|
|
::= { cLD11ClientCalibEntry 2 }
|
|
|
|
cLD11ClientCalibRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The object that represents the status of a
|
|
specific instance of a row in this table.
|
|
Initially set to a value of 'createAndGo' by
|
|
the User when a row is created, the status
|
|
as represented by this object is automatically
|
|
set to 'active' if and when the row creation
|
|
is successful. To delete the specific instance
|
|
of a row, User should set this object to
|
|
'destroy'. To create an entry in this table, it is
|
|
mandatory to specify the cLD11ClientCalibMacAddress,
|
|
cLD11ClientCalibNumberOfRadios (number of radios
|
|
to be used in the calibration) and
|
|
cLD11ClientCalibNumberOfSamples (no. of calibration
|
|
samples to be collected per radio)."
|
|
::= { cLD11ClientCalibEntry 3 }
|
|
|
|
cLD11ClientCalibNumberOfRadios OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the number of radios
|
|
used in this calibration."
|
|
::= { cLD11ClientCalibEntry 4 }
|
|
|
|
cLD11ClientCalibNumberOfSamples OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the number of RSSI samples for
|
|
a given radio, used in this calibration."
|
|
::= { cLD11ClientCalibEntry 5 }
|
|
|
|
cLD11ClientCalibSamplesCollected OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the number of
|
|
samples available for this client."
|
|
::= { cLD11ClientCalibEntry 6 }
|
|
|
|
cLD11ClientCalibBeaconIntervalExt OBJECT-TYPE
|
|
SYNTAX TimeInterval
|
|
UNITS "hundredths-seconds"
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the time interval, expressed
|
|
here in hundredths of a second at which an AP
|
|
issues radio measurement request messages to a
|
|
client for every SSID. It is not recommended to
|
|
configure values less than 10 seconds (1000).
|
|
The value configured through this object is
|
|
reflected in the operation of the LWAPP APs only if
|
|
cLD11ClientCalibBeaconEnabled is set to 'true'."
|
|
DEFVAL { 60000 }
|
|
::= { cLD11ClientCalibEntry 7 }
|
|
|
|
cLD11ClientCalibStorageType OBJECT-TYPE
|
|
SYNTAX StorageType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the storage type of this
|
|
conceptual row."
|
|
DEFVAL { volatile }
|
|
::= { cLD11ClientCalibEntry 8 }
|
|
|
|
|
|
|
|
cLD11ClientCalibTableMaxEntries OBJECT-TYPE
|
|
SYNTAX Unsigned32 (1..25)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the maximum number of entries allowed
|
|
in cLD11ClientCalibTable."
|
|
::= { cldccConfig 2 }
|
|
-- ********************************************************************
|
|
-- * Client Calibration RSSI Data table
|
|
-- ********************************************************************
|
|
|
|
cLD11ClientCalibDataTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CLD11ClientCalibDataEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains the RSSI data samples
|
|
collected for 802.11 client based on the
|
|
information provided in the cldccLD11ClientCalibTable.
|
|
Entries are automatically added by the controller
|
|
as and when samples are available.
|
|
This data is used by the NMS for location
|
|
calibration of the 8022.11 clients."
|
|
::= { cldccRssiSamples 1 }
|
|
|
|
cLD11ClientCalibDataEntry OBJECT-TYPE
|
|
SYNTAX CLD11ClientCalibDataEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Each entry represents a conceptual row in this
|
|
table and provides the information about the
|
|
samples for location calibration of a 802.11
|
|
client."
|
|
INDEX {
|
|
cLD11ClientCalibMacAddress,
|
|
cLApSysMacAddress,
|
|
cLApDot11IfSlotId,
|
|
clD11ClientCalibDataTimeStamp,
|
|
clD11ClientCalibDataAntennaIndex
|
|
}
|
|
::= { cLD11ClientCalibDataTable 1 }
|
|
|
|
CLD11ClientCalibDataEntry ::= SEQUENCE {
|
|
clD11ClientCalibDataTimeStamp TimeStamp,
|
|
clD11ClientCalibDataAntennaIndex INTEGER,
|
|
clD11ClientCalibDataRssiValue Integer32,
|
|
clD11ClientCalibDataTransmitPower Integer32
|
|
}
|
|
|
|
clD11ClientCalibDataTimeStamp OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the time this sample was
|
|
collected. This is the absolute system time that
|
|
this sample was collected."
|
|
::= { cLD11ClientCalibDataEntry 1 }
|
|
|
|
clD11ClientCalibDataAntennaIndex OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
antenna1(1),
|
|
antenna2(2)
|
|
}
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the antenna which
|
|
received the probe request from client."
|
|
::= { cLD11ClientCalibDataEntry 2 }
|
|
|
|
clD11ClientCalibDataRssiValue OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the RSSI value for this
|
|
sample."
|
|
::= { cLD11ClientCalibDataEntry 3 }
|
|
|
|
clD11ClientCalibDataTransmitPower OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
UNITS "dbm"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the transmit power level for
|
|
a calibrating client."
|
|
::= { cLD11ClientCalibDataEntry 4 }
|
|
|
|
|
|
|
|
-- ********************************************************************
|
|
-- * Location scalars
|
|
-- ********************************************************************
|
|
|
|
cLD11ClientCalibRssiAlgorithm OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
simple(2),
|
|
average(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the algorithm used
|
|
to average RSSI and SNR values.
|
|
unknown(1) - the algorithm used is unknown
|
|
simple(2) - simple is used for the calculation
|
|
average(3) - average RSSI is used as algorithm"
|
|
::= { cldccConfig 3 }
|
|
|
|
cLD11ClientCalibRssiClientExpiryTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the expiry timeout
|
|
for the client."
|
|
::= { cldccConfig 4 }
|
|
|
|
cLD11ClientCalibRssiCalibClientExpiryTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the expiry timeout
|
|
for the calibrating client."
|
|
::= { cldccConfig 5 }
|
|
|
|
cLD11ClientCalibRssiRfidTagExpiryTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the expiry timeout
|
|
for the RFID tags."
|
|
::= { cldccConfig 6 }
|
|
|
|
cLD11ClientCalibRssiRogueApExpiryTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the expiry timeout
|
|
for the Rogue APs."
|
|
::= { cldccConfig 7 }
|
|
|
|
cLD11ClientCalibRssiClientHalflifeTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the half-life timeout
|
|
for the client. A value of 0 indicates that
|
|
timeout is disabled."
|
|
::= { cldccConfig 8 }
|
|
|
|
cLD11ClientCalibRssiCalibClientHalflifeTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the half-life timeout
|
|
for the calibrating client. A value of 0 indicates
|
|
that timeout is disabled."
|
|
::= { cldccConfig 9 }
|
|
|
|
cLD11ClientCalibRssiRfidTagHalflifeTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the half-life timeout
|
|
for the RFID tags. A value of 0 indicates that
|
|
timeout is disabled."
|
|
::= { cldccConfig 10 }
|
|
|
|
cLD11ClientCalibRssiRogueApHalflifeTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the half-life timeout
|
|
for the Rogue APs. A value of 0 indicates that
|
|
timeout is disabled."
|
|
::= { cldccConfig 11 }
|
|
|
|
cLD11ClientCalibRfidDataEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether the RFID tag data
|
|
collection is enabled."
|
|
::= { cldccConfig 12 }
|
|
|
|
cLD11ClientCalibRfidTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the RFID tag data timeout."
|
|
::= { cldccConfig 13 }
|
|
|
|
cLD11ClientCalibClientMultiBandEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether calibrating client
|
|
uses both the bands to transmit the requests.
|
|
|
|
true - the calibrating client uses both the bands
|
|
to transmit the requests.
|
|
false - the calibrating client uses single band
|
|
to transmit the requests."
|
|
::= { cldccConfig 14 }
|
|
|
|
cLD11ClientCalibClientRequestEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether calibrating client
|
|
uses uni band or multi band to transmit the requests.
|
|
|
|
true - the calibrating client uses uni band or
|
|
multi band to transmit the requests.
|
|
false - the calibrating client does not use
|
|
any band for transmitting requests."
|
|
::= { cldccConfig 15 }
|
|
|
|
cLD11ClientCalibClientBurstIntervalEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether calibrating client
|
|
burst interval is enabled.
|
|
|
|
true - the calibrating client burst interval
|
|
is enabled.
|
|
false - the calibrating client burst interval
|
|
is disabled."
|
|
::= { cldccConfig 16 }
|
|
|
|
cLD11ClientCalibClientBurstInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the burst interval of
|
|
the calibrating client."
|
|
::= { cldccConfig 17 }
|
|
|
|
cLD11ClientCalibClientInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the notification interval
|
|
for calibrating clients."
|
|
::= { cldccConfig 18 }
|
|
|
|
cLD11ClientCalibRfidInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the notification interval
|
|
for RFID tags."
|
|
::= { cldccConfig 19 }
|
|
|
|
cLD11ClientCalibRogueInterval OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the notification interval
|
|
for Rogue APs and Rogue clients."
|
|
::= { cldccConfig 20 }
|
|
|
|
cLD11RfidRssiExpiryTime OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Rssi expiry time
|
|
for RFID location tag."
|
|
::={ cldccConfig 21 }
|
|
|
|
cLD11RfidRssiHalflifeTime OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Rssi half-life time
|
|
for RFID location tag."
|
|
::={ cldccConfig 22 }
|
|
|
|
cLD11RfidNotifyThresholdTime OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the notify-threshold time
|
|
for RFID tag."
|
|
::={ cldccConfig 24 }
|
|
|
|
cLD11RfidDataEnable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies enable and disable the
|
|
for RFID etag.
|
|
|
|
true - RFID tag collection is enabled
|
|
false - RFID tag collection is disabled"
|
|
|
|
::={ cldccConfig 25 }
|
|
|
|
cLD11RfidTimeout OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
UNITS "seconds"
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the notify-threshold time
|
|
for RFID tag."
|
|
|
|
::={ cldccConfig 26 }
|
|
|
|
-- *******************************************************************
|
|
-- * Compliance statements
|
|
-- ********************************************************************
|
|
|
|
ciscoLwappDot11ClientCalibMIBCompliances OBJECT IDENTIFIER
|
|
::= { ciscoLwappDot11ClientCalibMIBConform 1 }
|
|
|
|
ciscoLwappDot11ClientCalibMIBGroups OBJECT IDENTIFIER
|
|
::= { ciscoLwappDot11ClientCalibMIBConform 2 }
|
|
|
|
|
|
-- STATUS deprecated by ciscoLwappDot11ClientCalibMIBComplianceRev1
|
|
|
|
ciscoLwappDot11ClientCalibMIBCompliance MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for the SNMP entities that
|
|
implement this MIB."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS { ciscoLwappDot11ClientCalibMIBConfigGroup }
|
|
::= { ciscoLwappDot11ClientCalibMIBCompliances 1 }
|
|
|
|
ciscoLwappDot11ClientCalibMIBComplianceRev1 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for the SNMP entities that
|
|
implement this MIB."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
cLD11ClientCalibClientConfigGroup,
|
|
cLD11ClientCalibGlobalConfigGroup,
|
|
cLD11ClientCalibRssiDataSampleGroup
|
|
}
|
|
|
|
OBJECT cLD11ClientCalibRowStatus
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibBeaconIntervalExt
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibNumberOfRadios
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibNumberOfSamples
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibStorageType
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibTableMaxEntries
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiAlgorithm
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiClientExpiryTimeout
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiCalibClientExpiryTimeout
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiRfidTagExpiryTimeout
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiRogueApExpiryTimeout
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiClientHalflifeTimeout
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiCalibClientHalflifeTimeout
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiRfidTagHalflifeTimeout
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRssiRogueApHalflifeTimeout
|
|
SYNTAX Unsigned32 (0..2 | 5 | 10 | 20 | 30
|
|
| 60 | 90 | 120 | 180 | 300)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRfidDataEnable
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRfidTimeout
|
|
SYNTAX Unsigned32 (60..7200)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibClientMultiBandEnable
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibClientRequestEnable
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibClientBurstIntervalEnable
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibClientBurstInterval
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibClientInterval
|
|
SYNTAX Unsigned32 (1..180)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRfidInterval
|
|
SYNTAX Unsigned32 (1..180)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
|
|
OBJECT cLD11ClientCalibRogueInterval
|
|
SYNTAX Unsigned32 (1..180)
|
|
MIN-ACCESS read-only
|
|
DESCRIPTION
|
|
"Write access is not required."
|
|
::= { ciscoLwappDot11ClientCalibMIBCompliances 2 }
|
|
|
|
-- ********************************************************************
|
|
-- * Units of conformance
|
|
-- ********************************************************************
|
|
|
|
ciscoLwappDot11ClientCalibMIBConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cLD11ClientCalibBeaconInterval,
|
|
cLD11ClientCalibRowStatus,
|
|
cLD11ClientCalibTableMaxEntries
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This collection of objects specifies the required
|
|
calibration parameters for the 802.11 wireless clients.
|
|
ciscoLwappDot11ClientCalibMIBConfigGroup object is
|
|
superseded by cLD11ClientCalibClientConfigGroup."
|
|
::= { ciscoLwappDot11ClientCalibMIBGroups 1 }
|
|
|
|
cLD11ClientCalibClientConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cLD11ClientCalibRowStatus,
|
|
cLD11ClientCalibBeaconIntervalExt,
|
|
cLD11ClientCalibNumberOfRadios,
|
|
cLD11ClientCalibNumberOfSamples,
|
|
cLD11ClientCalibSamplesCollected,
|
|
cLD11ClientCalibStorageType,
|
|
cLD11ClientCalibTableMaxEntries
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects providing the required
|
|
calibration parameters for the 802.11 wireless
|
|
clients."
|
|
::= { ciscoLwappDot11ClientCalibMIBGroups 2 }
|
|
|
|
cLD11ClientCalibGlobalConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cLD11ClientCalibRssiAlgorithm,
|
|
cLD11ClientCalibRssiClientExpiryTimeout,
|
|
cLD11ClientCalibRssiCalibClientExpiryTimeout,
|
|
cLD11ClientCalibRssiRfidTagExpiryTimeout,
|
|
cLD11ClientCalibRssiRogueApExpiryTimeout,
|
|
cLD11ClientCalibRssiClientHalflifeTimeout,
|
|
cLD11ClientCalibRssiCalibClientHalflifeTimeout,
|
|
cLD11ClientCalibRssiRfidTagHalflifeTimeout,
|
|
cLD11ClientCalibRssiRogueApHalflifeTimeout,
|
|
cLD11ClientCalibRfidDataEnable,
|
|
cLD11ClientCalibRfidTimeout,
|
|
cLD11ClientCalibClientMultiBandEnable,
|
|
cLD11ClientCalibClientRequestEnable,
|
|
cLD11ClientCalibClientBurstIntervalEnable,
|
|
cLD11ClientCalibClientBurstInterval,
|
|
cLD11ClientCalibClientInterval,
|
|
cLD11ClientCalibRfidInterval,
|
|
cLD11ClientCalibRogueInterval,
|
|
cLD11RfidRssiExpiryTime,
|
|
cLD11RfidRssiHalflifeTime,
|
|
cLD11RfidNotifyThresholdTime,
|
|
cLD11RfidDataEnable,
|
|
cLD11RfidTimeout
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects providing the required
|
|
RSSI calibration parameters for the 802.11 wireless
|
|
clients."
|
|
::= { ciscoLwappDot11ClientCalibMIBGroups 3 }
|
|
|
|
cLD11ClientCalibRssiDataSampleGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
clD11ClientCalibDataRssiValue,
|
|
clD11ClientCalibDataTransmitPower
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This collection of objects providing the RSSI data
|
|
samples collected for 802.11 client."
|
|
::= { ciscoLwappDot11ClientCalibMIBGroups 4 }
|
|
|
|
END
|
|
|
|
|