1668 lines
54 KiB
Plaintext
1668 lines
54 KiB
Plaintext
-- *********************************************************************
|
|
-- CISCO-VOICE-ATM-TRUNK-MIB.my:
|
|
--
|
|
-- Cisco ATM Trunk MIB
|
|
--
|
|
--
|
|
-- January 2003, Feng Luo
|
|
--
|
|
-- Copyright (c) 2003 by cisco Systems, Inc.
|
|
-- All rights reserved.
|
|
--
|
|
-- *********************************************************************
|
|
|
|
|
|
CISCO-ATM-TRUNK-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
RowStatus,
|
|
TimeStamp,
|
|
TruthValue,
|
|
TEXTUAL-CONVENTION FROM SNMPv2-TC
|
|
MODULE-COMPLIANCE,
|
|
OBJECT-GROUP FROM SNMPv2-CONF
|
|
OBJECT-TYPE,
|
|
MODULE-IDENTITY,
|
|
Integer32,
|
|
Gauge32,
|
|
Unsigned32 FROM SNMPv2-SMI
|
|
ifIndex,
|
|
InterfaceIndex FROM IF-MIB
|
|
CiscoAal2ProfileNumber,
|
|
CiscoAal2ProfileType FROM CISCO-VOICE-AALX-PROFILE-MIB
|
|
ciscoMgmt FROM CISCO-SMI
|
|
ConfigIterator,
|
|
BulkConfigResult FROM CISCO-TC
|
|
OwnerString FROM RMON-MIB
|
|
CvcSpeechCoderRate,
|
|
CvcCoderTypeRate FROM CISCO-VOICE-COMMON-DIAL-CONTROL-MIB;
|
|
|
|
|
|
|
|
ciscoAtmTrunkMIB MODULE-IDENTITY
|
|
LAST-UPDATED "200307180000Z"
|
|
ORGANIZATION "Cisco Systems, Inc."
|
|
CONTACT-INFO
|
|
" Cisco Systems
|
|
Customer Service
|
|
|
|
Postal: 170 W Tasman Drive
|
|
San Jose, CA 95134
|
|
USA
|
|
|
|
Tel: +1 800 553-NETS
|
|
|
|
E-mail: cs-voice-gateway@cisco.com"
|
|
DESCRIPTION
|
|
"The MIB for voice and Nx64 over ATM Trunking applications.
|
|
|
|
The following lists the abbreviations used in this MIB:
|
|
AAL ATM Adaption Layer
|
|
AIS Alarm Indication Signal
|
|
CID Channel Identifier
|
|
DSP Digital Signal Processing
|
|
DTMF Dual Tone Multi Frequency
|
|
FCS Frame Check Sequence
|
|
TDM Time Division Multiplexing
|
|
PVC Permanent Virtual Circuit
|
|
RAI Remote Alarm Indication
|
|
RDI Remote Defect Indication
|
|
SID Silence Insertion Descriptor
|
|
SVC Switched Virtual Circuit
|
|
VAD Voice Activity Detection
|
|
VBD Voice Band Data
|
|
VC Virtual Circuit
|
|
"
|
|
REVISION "200307180000Z"
|
|
DESCRIPTION
|
|
"Initial version of the MIB module."
|
|
|
|
::= { ciscoMgmt 351 }
|
|
|
|
|
|
cAtmTrunkMIBNotifications
|
|
OBJECT IDENTIFIER ::= { ciscoAtmTrunkMIB 0 }
|
|
cAtmTrunkMIBObjects
|
|
OBJECT IDENTIFIER ::= { ciscoAtmTrunkMIB 1 }
|
|
cAtmTrunkCidConfig
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBObjects 1 }
|
|
cAtmTrunkCidConnStats
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBObjects 2 }
|
|
cAtmTrunkAal1Config
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBObjects 3 }
|
|
cAtmTrunkAal1ConnStats
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBObjects 4 }
|
|
cAtmTrunkAal5Config
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBObjects 5 }
|
|
cAtmTrunkAal5ConnStats
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBObjects 6 }
|
|
|
|
--
|
|
-- Textual Conventions
|
|
--
|
|
Counter32SinceReset ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This textual convention defines a counter type that is
|
|
similar to Counter32 but can be reset. The value of the
|
|
objects of this type indicates the statistics since last
|
|
counter reset.
|
|
|
|
Once the value of the counter object of this type reaches
|
|
its maximum, it will restart from zero again.
|
|
"
|
|
SYNTAX Unsigned32 (0..2147483647)
|
|
|
|
--
|
|
-- caTrunkCidTable
|
|
--
|
|
catmtCidTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CatmtCidEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table is used to establish the mapping of one or more
|
|
DS0 channels from a single DS1 interface to an AAL2 connection
|
|
identified by a Channel IDentification number(CID).
|
|
|
|
This table is created and used for ATM AAL2 trunking
|
|
applications including both voice and data.
|
|
"
|
|
::= { cAtmTrunkCidConfig 1 }
|
|
|
|
catmtCidEntry OBJECT-TYPE
|
|
SYNTAX CatmtCidEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry in the catmtCidTable.
|
|
Each entry represents an AAL2 trunking connection which
|
|
is uniquely identified by the PVC index and the CID number.
|
|
|
|
An AAL2 trunking connection is established by binding
|
|
one or more DS0 channels from a single DS1 interface to
|
|
an AAL2 ATM connection identified by the CID.
|
|
|
|
The Channel IDentification (CID) is the standard term
|
|
used to identify an ATM AAL2 connection (ITU-T I.366.2).
|
|
CID is unique within a VC, either a PVC or SVC connection.
|
|
"
|
|
INDEX { ifIndex, catmtCidVpi, catmtCidVci, catmtCid }
|
|
::= { catmtCidTable 1 }
|
|
|
|
|
|
CatmtCidEntry ::=
|
|
SEQUENCE {
|
|
catmtCidVpi Unsigned32,
|
|
catmtCidVci Unsigned32,
|
|
catmtCid Integer32,
|
|
catmtCidDs1 InterfaceIndex,
|
|
catmtCidDs0GroupIndex Integer32,
|
|
catmtCidProfileType CiscoAal2ProfileType,
|
|
catmtCidProfileNumber CiscoAal2ProfileNumber,
|
|
catmtCidVoiceCodec CvcSpeechCoderRate,
|
|
catmtCidVBDCodec CvcCoderTypeRate,
|
|
catmtCidNx64Enable TruthValue,
|
|
catmtCidNx64Profile Integer32,
|
|
catmtCidStateBitMap BITS,
|
|
catmtCidRepetition ConfigIterator,
|
|
catmtCidRepetitionOwner OwnerString,
|
|
catmtCidRepetitionResult BulkConfigResult,
|
|
catmtCidRowStatus RowStatus
|
|
}
|
|
|
|
|
|
catmtCidVpi OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4095)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the VPI value of an ATM PVC connection.
|
|
"
|
|
::= { catmtCidEntry 1 }
|
|
|
|
catmtCidVci OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the VCI value of an ATM PVC connection.
|
|
"
|
|
::= { catmtCidEntry 2 }
|
|
|
|
catmtCid OBJECT-TYPE
|
|
SYNTAX Integer32 (8..255)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the CID of an ATM AAL2 connection,
|
|
it is unique within a PVC or SVC connection.
|
|
|
|
The CID number at both sides of an AAL2 connection
|
|
must be the same.
|
|
|
|
Value of 0 is not used, and values of 1 to 7 are reserved
|
|
for layer management by ITU-T I.366.2 standard.
|
|
"
|
|
REFERENCE
|
|
"ITU-T recommendation I.366.2. "
|
|
::= { catmtCidEntry 3 }
|
|
|
|
catmtCidDs1 OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object equals to the 'ifIndex' of the
|
|
DS1 interface.
|
|
|
|
This object is mandatory when adding a CID entry. Once a
|
|
CID entry is added, this object can not be modified.
|
|
"
|
|
::= { catmtCidEntry 4 }
|
|
|
|
catmtCidDs0GroupIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (0..30)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An arbitrary index that uniquely identifies a DS0 group
|
|
which contains one or more DS0(s) within a DS1 interface
|
|
specified by 'catmtCidDs1'.
|
|
|
|
This object is mandatory when adding a CID entry. Once a
|
|
CID entry is added, this object can not be modified.
|
|
"
|
|
::= { catmtCidEntry 5 }
|
|
|
|
catmtCidProfileType OBJECT-TYPE
|
|
SYNTAX CiscoAal2ProfileType
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the type of the AAL2 CODEC profile.
|
|
The combination of the profile type and profile number
|
|
specified by 'catmtCidProfileNumber' defines an AAL2
|
|
CODEC profile.
|
|
|
|
This parameter is mandatory for adding and a voice trunking
|
|
CID entry.
|
|
|
|
This object is applicable when catmtCidNx64Enable is
|
|
is set to 'false'. It is used for voice trunking applications
|
|
only.
|
|
"
|
|
::= { catmtCidEntry 6 }
|
|
|
|
catmtCidProfileNumber OBJECT-TYPE
|
|
SYNTAX CiscoAal2ProfileNumber
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the AAL2 CODEC profile number.
|
|
The combination of profile type and profile number defines
|
|
an AAL2 CODEC profile.
|
|
|
|
A profile contains one or more entries, with each entry
|
|
specifying an encoding algorithm and information regarding
|
|
how the TDM data is to be packed into a packet.
|
|
|
|
This parameter is mandatory for adding a voice trunking CID
|
|
entry.
|
|
|
|
This object is applicable when catmtCidNx64Enable is
|
|
is set to 'false'. It is used for voice trunking applications
|
|
only.
|
|
"
|
|
REFERENCE
|
|
" ITU-T recommendation I.366.2."
|
|
::= { catmtCidEntry 7 }
|
|
|
|
catmtCidVoiceCodec OBJECT-TYPE
|
|
SYNTAX CvcSpeechCoderRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the CODEC type used for the AAL2
|
|
trunking connection.
|
|
|
|
The following table lists the CODEC types specified
|
|
in each profile table by ITU I.366.2 standard.
|
|
|
|
----------------------------------------------------
|
|
Profile Profile Packet
|
|
type Number CODEC SID time(ms)
|
|
----------------------------------------------------
|
|
ITU 1 G.711u No SID 5
|
|
G.711a No SID 5
|
|
----------------------------------------------------
|
|
ITU 2 G.711u SIDG 5
|
|
G.711a SIDG 5
|
|
----------------------------------------------------
|
|
ITU 3 G.711u SIDG 5
|
|
G.711a SIDG 5
|
|
G726-40 SIDG 5
|
|
G726-32 SIDG 5
|
|
G726-24 SIDG 5
|
|
G726-16 SIDG 5
|
|
----------------------------------------------------
|
|
ITU 7 G.711u SIDG 5
|
|
G.711a SIDG 5
|
|
G.729ab SID729 10
|
|
G.729a No SID 10
|
|
----------------------------------------------------
|
|
ITU 8 G.711u No SID 5
|
|
G.711a No SID 5
|
|
G.726-32 No SID 5
|
|
G.729ab SID729 10
|
|
G.729a SID729 10
|
|
----------------------------------------------------
|
|
Custom 100 G.711u SIDG 5
|
|
G.711a SIDG 5
|
|
G.726-32 SIGD 10
|
|
----------------------------------------------------
|
|
Custom 101 G.711u No SID 5
|
|
G.711a No SID 5
|
|
G.726-32 No SID 10
|
|
G.729ab SID729 10
|
|
G.729a No SID 10
|
|
----------------------------------------------------
|
|
Custom 110 G.711u SIDG 5
|
|
G.711a SIDG 5
|
|
G.726-32 SIDG 10
|
|
G.729ab SID729 30
|
|
G.729a No SID 30
|
|
----------------------------------------------------
|
|
Custom 200 clearChan No SID 5
|
|
----------------------------------------------------
|
|
|
|
This object can only be set to the CODECs defined by
|
|
the profile specified by catmtCidProfileType and
|
|
catmtCidProfileNumber.
|
|
|
|
This object is applicable when catmtCidNx64Enable is
|
|
is set to 'false'. It is used for voice trunking applications
|
|
only.
|
|
|
|
This object is mandatory when adding a voice trunking CID
|
|
entry.
|
|
"
|
|
::= { catmtCidEntry 8 }
|
|
|
|
catmtCidVBDCodec OBJECT-TYPE
|
|
SYNTAX CvcCoderTypeRate
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the CODEC type to be used for Voice
|
|
Band Data (VBD) upspeed.
|
|
|
|
Upspeed is to change the transmission rate of a voice
|
|
interface to a higher rate of CODEC type for fax/modem
|
|
transportation.
|
|
|
|
This object is applicable when catmtCidNx64Enable is
|
|
is set to 'false'. It is used for voice trunking applications
|
|
only.
|
|
|
|
This object is mandatory when adding a voice trunking CID
|
|
entry.
|
|
"
|
|
::= { catmtCidEntry 9 }
|
|
|
|
catmtCidNx64Enable OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies whether a CID entry is in the Nx64
|
|
packet stream mode.
|
|
|
|
When this object is set to 'false', the CID connection is
|
|
for voice trunking applications only; when it is set to
|
|
'true', the CID connection is for data trunking using
|
|
Nx64 packet stream (N>=1).
|
|
|
|
This object can not be modified.
|
|
"
|
|
DEFVAL { false }
|
|
::= { catmtCidEntry 10 }
|
|
|
|
catmtCidNx64Profile OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Nx64 data profile for an AAL2
|
|
data trunking connection.
|
|
|
|
The value of this object is a valid index of the
|
|
cdapNx64ProfileTable in the CISCO-DATA-AALX-PROFILE-MIB.
|
|
|
|
This object is only applicable when catmtCidNx64Enable
|
|
is set to 'true'.
|
|
"
|
|
DEFVAL { 1 }
|
|
::= { catmtCidEntry 11 }
|
|
|
|
catmtCidStateBitMap OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
pvcAdminDown(0),
|
|
pvcFailure(1),
|
|
extAIS(2),
|
|
extRAI(3),
|
|
aal2ConnAIS(4),
|
|
aal2ConnRDI(5),
|
|
lineAlarm(6) }
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to indicate the state of the CID.
|
|
|
|
All bits setting to 0 which means status 'okay'.
|
|
"
|
|
REFERENCE
|
|
" ITU-T recommendation I.366.2 Annex N."
|
|
::= { catmtCidEntry 12 }
|
|
|
|
catmtCidRepetition OBJECT-TYPE
|
|
SYNTAX ConfigIterator
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used to repeatedly apply the writable objects
|
|
of catmtCidTable specified in the same SNMP PDU starting
|
|
from the row defined by the index object for the number of
|
|
rows specified by this object.
|
|
|
|
The repetition operation works differently for data trunking
|
|
and voice trunking applications. When catmtCidNx64Enable is
|
|
set to 'false' (voice trunking), it is iterated through the
|
|
value of DS0's and CID number. When catmtCidNx64Enable is
|
|
set to 'true' (data trunking), the order of repetition
|
|
operation is iterated through the value of DS1 index and CID
|
|
number.
|
|
|
|
(1) For voice trunking applications:
|
|
At each iteration, the value of CID (catmtCid), DS0
|
|
(catmtCidDs0GroupIndex) and DS1(catmtCidDs1) will
|
|
be incremented. When the value of catmtCidDs0GroupIndex
|
|
reaches its maximum, catmtCidDs1 will be incremented
|
|
to the next logical order of DS1 interface.
|
|
|
|
(2) For data trunking applications:
|
|
At each iteration, the value of catmtCid, catmtCidDs1
|
|
will be incremented. In other words, the Nx64 packet
|
|
stream repetition iterates on the DS1, with each DS1
|
|
interface having the same DS0 group
|
|
(catmtCidDs0GroupIndex) configuration.
|
|
|
|
The repetition iteration will stop once the value of catmtCid
|
|
reaches its maximum value 255 or when the next CID is not
|
|
available or already configured for different type of trunking
|
|
application. For example, a non-Nx64 repetition will stop if
|
|
the next CID has been configured for Nx64 packet stream
|
|
trunking, and vise versa. The repetition will also stop if the
|
|
next contiguous DS0 group index is not available.
|
|
|
|
The maximum value of this object is 248 which is the maximum
|
|
number of CID or AAL2 connections allowed within a VC
|
|
connection.
|
|
"
|
|
DEFVAL { 1 }
|
|
::= { catmtCidEntry 13 }
|
|
|
|
catmtCidRepetitionOwner OBJECT-TYPE
|
|
SYNTAX OwnerString
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used for error reporting of the bulk
|
|
provisioning operation specified by catmtCidRepetition.
|
|
|
|
The value of this object is set by the SNMP manager with its
|
|
own identifier at the time of setting catmtCidRepetition
|
|
to issue the bulk provisioning operation.
|
|
|
|
Later on, the SNMP manager checks the value of this object.
|
|
If it matches its own name, the value of
|
|
catmtCidRepetitionResult will be set to indicate the result
|
|
of bulk operation initiated by this SNMP manager.
|
|
"
|
|
::= { catmtCidEntry 14 }
|
|
|
|
catmtCidRepetitionResult OBJECT-TYPE
|
|
SYNTAX BulkConfigResult
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the result of the bulk provisioning
|
|
specified in catmtCidRepetition.
|
|
|
|
The format might look at (but not limited to):
|
|
'COMPLETION=<number of rows completed before any error
|
|
occurred>/<number of rows was designated>,
|
|
ERROR=<error code>/<index where the error occurred>:
|
|
<error text>'
|
|
|
|
For example:
|
|
'COMPLETION=22/100,ERROR=38/44:Invalid DS1 line coding
|
|
for the line type'
|
|
"
|
|
::= { catmtCidEntry 15 }
|
|
|
|
catmtCidRowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used for adding/deleting the entries from the
|
|
catmtCidTable.
|
|
|
|
In order to create a CID entry, the following parameters are
|
|
mandatory and must be provided:
|
|
|
|
For voice trunking applications:
|
|
catmtDs1,
|
|
catmtDs0GroupIndex,
|
|
catmtCidProfileType,
|
|
catmtCidProfileNumber,
|
|
catmtCidVoiceCodec,
|
|
catmtCidVBDCodec
|
|
|
|
For data trunking applications:
|
|
catmtDs1,
|
|
catmtDs0GroupIndex
|
|
"
|
|
::= { catmtCidEntry 16 }
|
|
|
|
|
|
--
|
|
-- catmtCidStatsTable
|
|
--
|
|
catmtCidStatsTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CatmtCidStatsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains the statistical information
|
|
on a per CID connection basis for AAL2 Trunking
|
|
applications.
|
|
"
|
|
::= { cAtmTrunkCidConnStats 1 }
|
|
|
|
catmtCidStatsEntry OBJECT-TYPE
|
|
SYNTAX CatmtCidStatsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains statistical information for an AAL2
|
|
connection. Each entry in this table corresponds to an AAL2
|
|
bearer connection that has been setup by mapping one or
|
|
more DS1/DS0s to an AAL2 connection identified by CID.
|
|
|
|
The entries in this table are implicitly created/deleted
|
|
at the time of creation/deletion of entries in the
|
|
catmtCidTable.
|
|
"
|
|
INDEX { ifIndex, catmtCidVpi, catmtCidVci, catmtCid }
|
|
::= { catmtCidStatsTable 1 }
|
|
|
|
|
|
CatmtCidStatsEntry ::=
|
|
SEQUENCE {
|
|
catmtCidSentPackets Counter32SinceReset,
|
|
catmtCidRcvdPackets Counter32SinceReset,
|
|
catmtCidSentOctets Counter32SinceReset,
|
|
catmtCidRcvdOctets Counter32SinceReset,
|
|
catmtCidLostPackets Counter32SinceReset,
|
|
catmtCidJitter Gauge32,
|
|
catmtCidExtAISCnts Counter32SinceReset,
|
|
catmtCidExtRAICnts Counter32SinceReset,
|
|
catmtCidConnAISCnts Counter32SinceReset,
|
|
catmtCidConnRDICnts Counter32SinceReset,
|
|
catmtCidNx64FramesTxToTDM Counter32SinceReset,
|
|
catmtCidNx64FramesRxFromTDM Counter32SinceReset,
|
|
catmtCidNx64EncBytesTxToTDM Counter32SinceReset,
|
|
catmtCidNx64EncBytesRxFromTDM Counter32SinceReset,
|
|
catmtCidNx64InvalidFCSFrames Counter32SinceReset,
|
|
catmtCidNx64AbortSeqFrames Counter32SinceReset,
|
|
catmtCidNx64InvalidShortFrames Counter32SinceReset,
|
|
catmtCidNx64InvalidLongFrames Counter32SinceReset,
|
|
catmtCidNx64NoByteAlignErrorFrames Counter32SinceReset,
|
|
catmtCidNx64RASTimeOutFrames Counter32SinceReset,
|
|
catmtCidLastResetTime TimeStamp,
|
|
catmtCidCounterClear TruthValue
|
|
}
|
|
|
|
catmtCidSentPackets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "packets"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the number of packets sent towards
|
|
network side since the connection setup.
|
|
"
|
|
::= { catmtCidStatsEntry 1 }
|
|
|
|
catmtCidRcvdPackets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "packets"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the count of packets received
|
|
from network side since the connection setup.
|
|
"
|
|
::= { catmtCidStatsEntry 2 }
|
|
|
|
catmtCidSentOctets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the count of bytes sent towards
|
|
network side since connection setup.
|
|
"
|
|
::= { catmtCidStatsEntry 3 }
|
|
|
|
catmtCidRcvdOctets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the count of bytes received from
|
|
network since connection setup.
|
|
"
|
|
::= { catmtCidStatsEntry 4 }
|
|
|
|
catmtCidLostPackets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "packets"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the count of packets lost in
|
|
the egress direction (from the network).
|
|
|
|
This number is computed based on the expected number
|
|
of packets and the actual number of packets arrived
|
|
from the network.
|
|
"
|
|
::= { catmtCidStatsEntry 5 }
|
|
|
|
catmtCidJitter OBJECT-TYPE
|
|
SYNTAX Gauge32 (0..65535)
|
|
UNITS "milliseconds"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the jitter (a.k.a interarrival jitter).
|
|
This value is determined by the gateway DSP and obtained by
|
|
the processor running on gateway upon querying the DSP
|
|
periodically.
|
|
"
|
|
::= { catmtCidStatsEntry 6 }
|
|
|
|
catmtCidExtAISCnts OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of external AIS AAL2 Type3
|
|
packets received.
|
|
|
|
External AIS : alarm indication signal associated with
|
|
a maintenance alarm detected on a defective maintenance
|
|
span, that is transmitted in the direction of the defect
|
|
as a substitute for normal signal. The purpose is to show
|
|
the downstream entities that a defect has been identified
|
|
and to prevent other maintenance alarms consequent to this
|
|
first defect.
|
|
"
|
|
REFERENCE
|
|
"ITU-T G.366.2 Annex N"
|
|
::= { catmtCidStatsEntry 7 }
|
|
|
|
catmtCidExtRAICnts OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of external RAI AAL2 Type3
|
|
packets received.
|
|
|
|
External RAI is transmitted upstream from an entity that
|
|
has detected defects persisting long enough to constitute
|
|
a received signal failure. External RAI is to report in
|
|
the backward direction to indicate there is an interruption
|
|
of service in the forward direction.
|
|
"
|
|
REFERENCE
|
|
"ITU-T G.366.2 Annex N"
|
|
::= { catmtCidStatsEntry 8 }
|
|
|
|
catmtCidConnAISCnts OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of external connection AIS
|
|
AAL2 packets received.
|
|
|
|
External Conn AIS is a Alarm Indicating Signal transmitted
|
|
in the downstream direction from the AAL2 connecting point
|
|
that first detects the defect affecting the AAL2 connection
|
|
including defects indicated by the lower layers.
|
|
"
|
|
REFERENCE
|
|
"ITU-T G.366.2 Annex N"
|
|
::= { catmtCidStatsEntry 9 }
|
|
|
|
catmtCidConnRDICnts OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of external connection
|
|
RDI AAL2 packets received.
|
|
|
|
External Connection RDI - is a signal transmitted in the
|
|
upstream direction by an AAL2 endpoint that is in alarm
|
|
state, as the result of having received an AAL2 connection
|
|
AIS or having detected a defect that affects the AAL2
|
|
connection.
|
|
"
|
|
REFERENCE
|
|
"ITU-T G.366.2 Annex N"
|
|
::= { catmtCidStatsEntry 10 }
|
|
|
|
catmtCidNx64FramesTxToTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of frames transmitted
|
|
to the TDM interface.
|
|
|
|
This object is only applicable when catmtCidNx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 11 }
|
|
|
|
catmtCidNx64FramesRxFromTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of frames received from
|
|
the TDM interface.
|
|
|
|
This object is only applicable when catmtCidNx64Mode is
|
|
set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 12 }
|
|
|
|
catmtCidNx64EncBytesTxToTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of encoded bytes
|
|
transmitted to the TDM interface.
|
|
"
|
|
::= { catmtCidStatsEntry 13 }
|
|
|
|
catmtCidNx64EncBytesRxFromTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of encoded bytes
|
|
received from the TDM interface.
|
|
"
|
|
::= { catmtCidStatsEntry 14 }
|
|
|
|
catmtCidNx64InvalidFCSFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid frames
|
|
received with invalid Frame Check Sequence (FCS) error.
|
|
|
|
This object is only applicable when catmtCidNx64Mode is
|
|
set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 15 }
|
|
|
|
catmtCidNx64AbortSeqFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid frames
|
|
received with invalid frame abort sequence error.
|
|
|
|
This object is only applicable when catmtCidNx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 16 }
|
|
|
|
catmtCidNx64InvalidShortFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid short
|
|
frames (length less than minimum length) received.
|
|
|
|
This object is only applicable when catmtCidNx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 17 }
|
|
|
|
catmtCidNx64InvalidLongFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid long
|
|
frames (length greater than maximum length) received.
|
|
|
|
This object is only applicable when catmtCidNx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 18 }
|
|
|
|
catmtCidNx64NoByteAlignErrorFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid frames
|
|
received with no byte alignment.
|
|
|
|
This object is only applicable when catmtCidNx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 19 }
|
|
|
|
catmtCidNx64RASTimeOutFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of frames received
|
|
with RAS timer timeout.
|
|
|
|
This object is only applicable when catmtCidNx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtCidStatsEntry 20 }
|
|
|
|
catmtCidLastResetTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the value of sysUpTime when the
|
|
last counter reset occurred.
|
|
|
|
If no counter reset has occurred since the last time
|
|
connection is established, this object will contain
|
|
value of zero.
|
|
"
|
|
::= { catmtCidStatsEntry 21 }
|
|
|
|
catmtCidCounterClear OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When this object is set to value of true(1), all statistics
|
|
counters with type of Counter32SinceReset in the table
|
|
catmtCidStatsTable will be reset to zero.
|
|
|
|
Setting this object to a value of false(2) has no implication.
|
|
|
|
This object will always return 'false' upon any SNMP
|
|
get operation. I
|
|
"
|
|
::= { catmtCidStatsEntry 22 }
|
|
|
|
--
|
|
-- AAL1 Trunking MIB
|
|
--
|
|
catmtAal1Table OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CatmtAal1Entry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table is used to establish the mapping of a
|
|
DS0 to an AAL1 ATM connection.
|
|
|
|
This table is created and used for ATM AAL1 trunking
|
|
applications only.
|
|
"
|
|
::= { cAtmTrunkAal1Config 1 }
|
|
|
|
catmtAal1Entry OBJECT-TYPE
|
|
SYNTAX CatmtAal1Entry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry in the catmtAal1Table.
|
|
|
|
Each entry represents an AAL1 trunking connection which
|
|
is uniquely identified by the PVC index.
|
|
|
|
An AAL1 trunking connection is established by binding
|
|
one or more DS0(s) from one single DS1 interface
|
|
to an AAL1 ATM connection identified the PVC index.
|
|
"
|
|
INDEX { ifIndex, catmtAal1Vpi, catmtAal1Vci }
|
|
::= { catmtAal1Table 1 }
|
|
|
|
|
|
CatmtAal1Entry ::=
|
|
SEQUENCE {
|
|
catmtAal1Vpi Unsigned32,
|
|
catmtAal1Vci Unsigned32,
|
|
catmtAal1Ds1 InterfaceIndex,
|
|
catmtAal1Ds0GroupIndex Integer32,
|
|
catmtAal1Nx64Profile Integer32,
|
|
catmtAal1RowStatus RowStatus
|
|
}
|
|
|
|
catmtAal1Vpi OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4095)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the VPI value of an ATM PVC connection.
|
|
"
|
|
::= { catmtAal1Entry 1 }
|
|
|
|
catmtAal1Vci OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the VCI value of an ATM PVC connection.
|
|
"
|
|
::= { catmtAal1Entry 2 }
|
|
|
|
catmtAal1Ds1 OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object is equivalent to the 'ifIndex'
|
|
of the DS1 interface.
|
|
|
|
This object is mandatory when adding an AAL1 entry.
|
|
Once an AAL1 entry is added, this object can not be
|
|
modified.
|
|
"
|
|
::= { catmtAal1Entry 3 }
|
|
|
|
catmtAal1Ds0GroupIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (0..30)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An arbitrary index that uniquely identifies one or a group
|
|
of DS0s to be connected to an AAL1 trunking connection.
|
|
|
|
When catmtAal1Nx64Enable is set to 'false', the AAL1
|
|
trunking connection can only be a mapping of one single DS0
|
|
to one AAL1 ATM connection.
|
|
|
|
This object is mandatory when adding an AAL1 entry. Once
|
|
an AAL1 entry is added, this object can not be modified.
|
|
"
|
|
::= { catmtAal1Entry 4 }
|
|
|
|
catmtAal1Nx64Profile OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Nx64 AAL1 data profile for an AAL1
|
|
trunking connection.
|
|
|
|
The value of this object is a valid index of
|
|
cdapNx64Aal1ProfileTable in CISCO-DATA-AALX-PROFILE-MIB.
|
|
"
|
|
DEFVAL { 1 }
|
|
::= { catmtAal1Entry 5 }
|
|
|
|
catmtAal1RowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used for adding/deleting the entries from
|
|
the catmtAal1Table.
|
|
|
|
In order to create an AAL1 trunking entry, the following
|
|
parameters are mandatory and must be provided:
|
|
catmtAal1Ds1,
|
|
catmtAal1Ds0GroupIdx
|
|
"
|
|
::= { catmtAal1Entry 6 }
|
|
|
|
|
|
--
|
|
-- AAL1 Trunking Statistics MIB
|
|
--
|
|
catmtAal1StatsTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CatmtAal1StatsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains the statistics information
|
|
on a per AAL1 connection basis for ATM AAL1
|
|
Trunking applications.
|
|
"
|
|
::= { cAtmTrunkAal1ConnStats 1 }
|
|
|
|
|
|
catmtAal1StatsEntry OBJECT-TYPE
|
|
SYNTAX CatmtAal1StatsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains statistics information for an AAL1
|
|
trunking connection.
|
|
|
|
Each entry in this table corresponds to an AAL1 connection
|
|
that has been setup by binding an DS0 to an AAL1 connection
|
|
identified by (ifIndex, catmtAal1Vpi, catmtAal1Vci).
|
|
|
|
The entries in this table are implicitly created/deleted
|
|
at the time of creation/deletion of entries in the
|
|
catmtAal1Table.
|
|
"
|
|
INDEX { ifIndex, catmtAal1Vpi, catmtAal1Vci }
|
|
::= { catmtAal1StatsTable 1 }
|
|
|
|
CatmtAal1StatsEntry ::=
|
|
SEQUENCE {
|
|
catmtAal1TxCells Counter32SinceReset,
|
|
catmtAal1RxCells Counter32SinceReset,
|
|
catmtAal1TxPayloadBytes Counter32SinceReset,
|
|
catmtAal1RxPayloadBytes Counter32SinceReset,
|
|
catmtAal1Jitter Gauge32,
|
|
catmtAal1LastResetTime TimeStamp,
|
|
catmtAal1CounterClear TruthValue
|
|
}
|
|
|
|
catmtAal1TxCells OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of ATM AAL1 cells
|
|
transmitted from gateway to ATM network.
|
|
"
|
|
::= { catmtAal1StatsEntry 1 }
|
|
|
|
catmtAal1RxCells OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of ATM AAL1 cells
|
|
gateway has received from ATM network.
|
|
"
|
|
::= { catmtAal1StatsEntry 2 }
|
|
|
|
catmtAal1TxPayloadBytes OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of payload bytes
|
|
transmitted from gateway to ATM network.
|
|
"
|
|
::= { catmtAal1StatsEntry 3 }
|
|
|
|
catmtAal1RxPayloadBytes OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of payload bytes
|
|
gateway has received from ATM network.
|
|
"
|
|
::= { catmtAal1StatsEntry 4 }
|
|
|
|
catmtAal1Jitter OBJECT-TYPE
|
|
SYNTAX Gauge32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the jitter (a.k.a interarrival jitter).
|
|
|
|
The value of this object is determined by the gateway DSP
|
|
and obtained by the processor running on gateway upon querying
|
|
the DSP periodically.
|
|
"
|
|
::= { catmtAal1StatsEntry 5 }
|
|
|
|
catmtAal1LastResetTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the value of sysUpTime when the
|
|
last counter reset occurred.
|
|
|
|
If no counter reset has occurred since the last time
|
|
system is up, this object will contain value of zero.
|
|
"
|
|
::= { catmtAal1StatsEntry 6 }
|
|
|
|
catmtAal1CounterClear OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When this object is set to value of true(1), all statistics
|
|
counters with type of Counter32SinceReset in the table
|
|
catmtAal1StatsTable will be reset to zero.
|
|
|
|
Setting this object to value of false(2) has no implication.
|
|
|
|
This object will always return 'false' upon any SNMP
|
|
get operation. I
|
|
"
|
|
::= { catmtAal1StatsEntry 7 }
|
|
|
|
|
|
--
|
|
-- AAL5 Trunking MIB
|
|
--
|
|
catmtAal5Table OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CatmtAal5Entry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table is used to establish the mapping of a
|
|
DS0 to an AAL5 ATM connection.
|
|
|
|
This table is created and used for ATM AAL5
|
|
trunking applications only.
|
|
"
|
|
::= { cAtmTrunkAal5Config 1 }
|
|
|
|
catmtAal5Entry OBJECT-TYPE
|
|
SYNTAX CatmtAal5Entry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry in the catmtAal5Table.
|
|
|
|
Each entry represents an AAL5 trunking connection which
|
|
is uniquely identified by the PVC index.
|
|
|
|
An AAL5 trunking connection is established by binding
|
|
a DS0 group voice interface containing one or more DS0
|
|
channels from one single DS1 interface to an AAL5 ATM
|
|
connection identified the PVC index.
|
|
"
|
|
INDEX { ifIndex, catmtAal5Vpi, catmtAal5Vci }
|
|
::= { catmtAal5Table 1 }
|
|
|
|
|
|
|
|
CatmtAal5Entry ::=
|
|
SEQUENCE {
|
|
catmtAal5Vpi Unsigned32,
|
|
catmtAal5Vci Unsigned32,
|
|
catmtAal5Ds1 InterfaceIndex,
|
|
catmtAal5Ds0GroupIndex Integer32,
|
|
catmtAal5Nx64Profile Integer32,
|
|
catmtAal5RowStatus RowStatus
|
|
}
|
|
|
|
catmtAal5Vpi OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4095)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the VPI value of an ATM PVC connection."
|
|
::= { catmtAal5Entry 1 }
|
|
|
|
catmtAal5Vci OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..65535)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is the VCI value of an ATM PVC connection."
|
|
::= { catmtAal5Entry 2 }
|
|
|
|
catmtAal5Ds1 OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The value of this object equals to the 'ifIndex' of
|
|
the DS1 interface.
|
|
|
|
This object is mandatory when adding an AAL5 entry.
|
|
Once an AAL5 entry is added, this object can not be
|
|
modified.
|
|
"
|
|
::= { catmtAal5Entry 3 }
|
|
|
|
catmtAal5Ds0GroupIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (0..30)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An arbitrary index that uniquely identifies a DS0 group
|
|
containing one or more DS0 that connect to an AAL5
|
|
trunking connection.
|
|
|
|
This object is mandatory when adding an AAL5 entry. Once
|
|
an AAL5 entry is added, this object can not be modified.
|
|
"
|
|
::= { catmtAal5Entry 4 }
|
|
|
|
catmtAal5Nx64Profile OBJECT-TYPE
|
|
SYNTAX Integer32 (1..65535)
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object specifies the Nx64 data profile for an AAL5
|
|
trunking connection.
|
|
|
|
The value of this object is a valid index of the
|
|
cdapNx64ProfileTable in CISCO-DATA-AALX-PROFILE-MIB.
|
|
"
|
|
DEFVAL {1}
|
|
::= { catmtAal5Entry 5 }
|
|
|
|
catmtAal5RowStatus OBJECT-TYPE
|
|
SYNTAX RowStatus
|
|
MAX-ACCESS read-create
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object is used for adding/deleting the entries from
|
|
the catmtAal5Table.
|
|
|
|
In order to create an AAL5 trunking entry, the following
|
|
parameters are mandatory and must be provided:
|
|
catmtAal5Ds1,
|
|
catmtAal5Ds0GroupIdx
|
|
"
|
|
::= { catmtAal5Entry 6 }
|
|
|
|
|
|
--
|
|
-- AAL5 Trunking Statistics MIB
|
|
--
|
|
catmtAal5StatsTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CatmtAal5StatsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains the statistical information
|
|
on a per AAL5 connection basis for ATM AAL5
|
|
Trunking applications.
|
|
"
|
|
::= { cAtmTrunkAal5ConnStats 1 }
|
|
|
|
catmtAal5StatsEntry OBJECT-TYPE
|
|
SYNTAX CatmtAal5StatsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This table contains statistical information for an AAL5
|
|
trunking connection.
|
|
|
|
Each entry in this table corresponds to an AAL5 connection
|
|
that has been setup by mapping one or more DS0(s) to an
|
|
AAL5 connection identified by ifIndex, catmtAal5Vpi and
|
|
atmtAal5Vci.
|
|
|
|
The entries in this table are implicitly created/deleted
|
|
at the time of creation/deletion of entries in the
|
|
catmtAal5Table.
|
|
"
|
|
INDEX { ifIndex, catmtAal5Vpi, catmtAal5Vci }
|
|
::= { catmtAal5StatsTable 1 }
|
|
|
|
|
|
CatmtAal5StatsEntry ::=
|
|
SEQUENCE {
|
|
catmtAal5SentPackets Counter32SinceReset,
|
|
catmtAal5RcvdPackets Counter32SinceReset,
|
|
catmtAal5SentOctets Counter32SinceReset,
|
|
catmtAal5RcvdOctets Counter32SinceReset,
|
|
catmtAal5FramesTxToTDM Counter32SinceReset,
|
|
catmtAal5FramesRxFromTDM Counter32SinceReset,
|
|
catmtAal5EncBytesTxToTDM Counter32SinceReset,
|
|
catmtAal5EncBytesRxFromTDM Counter32SinceReset,
|
|
catmtAal5InvalidFCSFrames Counter32SinceReset,
|
|
catmtAal5AbortSeqFrames Counter32SinceReset,
|
|
catmtAal5InvalidShortFrames Counter32SinceReset,
|
|
catmtAal5InvalidLongFrames Counter32SinceReset,
|
|
catmtAal5NoByteAlignErrorFrames Counter32SinceReset,
|
|
catmtAal5LastResetTime TimeStamp,
|
|
catmtAal5CounterClear TruthValue
|
|
}
|
|
|
|
catmtAal5SentPackets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "packets"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the number of packets sent towards
|
|
network side since the connection is up.
|
|
"
|
|
::= { catmtAal5StatsEntry 1 }
|
|
|
|
catmtAal5RcvdPackets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "packets"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the count of packets received
|
|
from network side since the connection setup.
|
|
"
|
|
::= { catmtAal5StatsEntry 2 }
|
|
|
|
catmtAal5SentOctets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the count of bytes sent towards
|
|
network side since connection setup.
|
|
"
|
|
::= { catmtAal5StatsEntry 3 }
|
|
|
|
catmtAal5RcvdOctets OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
UNITS "bytes"
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the count of bytes received from
|
|
network since connection setup.
|
|
"
|
|
::= { catmtAal5StatsEntry 4 }
|
|
|
|
catmtAal5FramesTxToTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of frames transmitted
|
|
to the TDM interface.
|
|
|
|
This object is only applicable when catmtAal5Nx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtAal5StatsEntry 5 }
|
|
|
|
catmtAal5FramesRxFromTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of frames received from
|
|
the TDM interface.
|
|
|
|
This object is only applicable when catmtAal5Nx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtAal5StatsEntry 6 }
|
|
|
|
catmtAal5EncBytesTxToTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of encoded bytes
|
|
transmitted to the TDM interface.
|
|
"
|
|
::= { catmtAal5StatsEntry 7 }
|
|
|
|
catmtAal5EncBytesRxFromTDM OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of encoded bytes
|
|
received from TDM interface.
|
|
"
|
|
::= { catmtAal5StatsEntry 8 }
|
|
|
|
catmtAal5InvalidFCSFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid frames
|
|
received with invalid Frame Check Sequence (FCS)
|
|
error.
|
|
|
|
This object is only applicable when catmtAal5Nx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtAal5StatsEntry 9 }
|
|
|
|
catmtAal5AbortSeqFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid frames
|
|
received with invalid frame abort sequence error.
|
|
|
|
This object is only applicable when catmtAal5Nx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtAal5StatsEntry 10 }
|
|
|
|
catmtAal5InvalidShortFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid short
|
|
frames (length less than minimum length) received.
|
|
|
|
This object is only applicable when catmtAal5Nx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtAal5StatsEntry 11 }
|
|
|
|
catmtAal5InvalidLongFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid long
|
|
frames (length greater than maximum length) received.
|
|
|
|
This object is only applicable when catmtAal5Nx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtAal5StatsEntry 12 }
|
|
|
|
catmtAal5NoByteAlignErrorFrames OBJECT-TYPE
|
|
SYNTAX Counter32SinceReset
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the number of invalid frames
|
|
received with no byte alignment.
|
|
|
|
This object is only applicable when catmtAal5Nx64Mode
|
|
is set to to 'hdlc'.
|
|
"
|
|
::= { catmtAal5StatsEntry 13 }
|
|
|
|
catmtAal5LastResetTime OBJECT-TYPE
|
|
SYNTAX TimeStamp
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object contains the value of sysUpTime when the
|
|
last counter reset occurred.
|
|
|
|
If no counter reset has occurred since the last time
|
|
system is up, this object will contain value of zero.
|
|
"
|
|
::= { catmtAal5StatsEntry 14 }
|
|
|
|
catmtAal5CounterClear OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When this object is set to value of true(1), all statistics
|
|
counters with type of Counter32SinceReset in the table
|
|
catmtAal5StatsTable will be reset to zero.
|
|
|
|
Setting this object to a value of false(2) has no implication.
|
|
|
|
This object will always return 'false' upon any SNMP
|
|
get operation. I
|
|
"
|
|
::= { catmtAal5StatsEntry 15 }
|
|
|
|
--
|
|
-- conformance information
|
|
--
|
|
|
|
cAtmTrunkMIBConformance
|
|
OBJECT IDENTIFIER ::= { ciscoAtmTrunkMIB 2 }
|
|
cAtmTrunkMIBCompliances
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBConformance 1 }
|
|
cAtmTrunkMIBGroups
|
|
OBJECT IDENTIFIER ::= { cAtmTrunkMIBConformance 2 }
|
|
|
|
-- compliance statements
|
|
|
|
|
|
cAtmTrunkMIBCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Compliance statement for CISCO-VOICE-ATM-TRUNK-MIB."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
cAtmTrunkCidMIBGroup,
|
|
cAtmTrunkAal1MIBGroup,
|
|
cAtmTrunkAal5MIBGroup,
|
|
cAtmTrunkCidConnStatsMIBGroup,
|
|
cAtmTrunkAal1ConnStatsMIBGroup,
|
|
cAtmTrunkAal5ConnStatsMIBGroup
|
|
}
|
|
::= { cAtmTrunkMIBCompliances 1 }
|
|
|
|
|
|
--
|
|
-- units of conformance
|
|
--
|
|
|
|
cAtmTrunkCidMIBGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
catmtCidDs1,
|
|
catmtCidDs0GroupIndex,
|
|
catmtCidProfileType,
|
|
catmtCidProfileNumber,
|
|
catmtCidVoiceCodec,
|
|
catmtCidVBDCodec,
|
|
catmtCidNx64Enable,
|
|
catmtCidNx64Profile,
|
|
catmtCidStateBitMap,
|
|
catmtCidRepetition,
|
|
catmtCidRepetitionOwner,
|
|
catmtCidRepetitionResult,
|
|
catmtCidRowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains objects related to
|
|
ATM AAL2 trunking CID level parameters."
|
|
::= { cAtmTrunkMIBGroups 1}
|
|
|
|
|
|
cAtmTrunkAal1MIBGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
catmtAal1Ds1,
|
|
catmtAal1Ds0GroupIndex,
|
|
catmtAal1Nx64Profile,
|
|
catmtAal1RowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains objects related to
|
|
ATM AAL1 trunking parameters."
|
|
::= { cAtmTrunkMIBGroups 2}
|
|
|
|
|
|
cAtmTrunkAal5MIBGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
catmtAal5Ds1,
|
|
catmtAal5Ds0GroupIndex,
|
|
catmtAal5Nx64Profile,
|
|
catmtAal5RowStatus
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains objects related to
|
|
ATM AAL5 trunking parameters."
|
|
::= { cAtmTrunkMIBGroups 3}
|
|
|
|
|
|
|
|
cAtmTrunkCidConnStatsMIBGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
catmtCidSentPackets,
|
|
catmtCidRcvdPackets,
|
|
catmtCidSentOctets,
|
|
catmtCidRcvdOctets,
|
|
catmtCidLostPackets,
|
|
catmtCidJitter,
|
|
catmtCidExtAISCnts,
|
|
catmtCidExtRAICnts,
|
|
catmtCidConnAISCnts,
|
|
catmtCidConnRDICnts,
|
|
catmtCidNx64FramesTxToTDM,
|
|
catmtCidNx64FramesRxFromTDM,
|
|
catmtCidNx64EncBytesTxToTDM,
|
|
catmtCidNx64EncBytesRxFromTDM,
|
|
catmtCidNx64InvalidFCSFrames,
|
|
catmtCidNx64AbortSeqFrames,
|
|
catmtCidNx64InvalidShortFrames,
|
|
catmtCidNx64InvalidLongFrames,
|
|
catmtCidNx64NoByteAlignErrorFrames,
|
|
catmtCidNx64RASTimeOutFrames,
|
|
catmtCidLastResetTime,
|
|
catmtCidCounterClear
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains objects for AAL2 bearer connection
|
|
statistics information used for ATM AAL2 trunking."
|
|
::= { cAtmTrunkMIBGroups 4}
|
|
|
|
|
|
cAtmTrunkAal1ConnStatsMIBGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
catmtAal1TxCells,
|
|
catmtAal1RxCells,
|
|
catmtAal1TxPayloadBytes,
|
|
catmtAal1RxPayloadBytes,
|
|
catmtAal1Jitter,
|
|
catmtAal1LastResetTime,
|
|
catmtAal1CounterClear
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains objects for AAL1 connection
|
|
statistics information used for ATM AAL1 trunking."
|
|
::= { cAtmTrunkMIBGroups 5}
|
|
|
|
|
|
cAtmTrunkAal5ConnStatsMIBGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
catmtAal5SentPackets,
|
|
catmtAal5RcvdPackets,
|
|
catmtAal5SentOctets,
|
|
catmtAal5RcvdOctets,
|
|
catmtAal5FramesTxToTDM,
|
|
catmtAal5FramesRxFromTDM,
|
|
catmtAal5EncBytesTxToTDM,
|
|
catmtAal5EncBytesRxFromTDM,
|
|
catmtAal5InvalidFCSFrames,
|
|
catmtAal5AbortSeqFrames,
|
|
catmtAal5InvalidShortFrames,
|
|
catmtAal5InvalidLongFrames,
|
|
catmtAal5NoByteAlignErrorFrames,
|
|
catmtAal5LastResetTime,
|
|
catmtAal5CounterClear
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This group contains objects for AAL5 bearer connection
|
|
statistics information used for ATM AAL5 trunking."
|
|
::= { cAtmTrunkMIBGroups 6}
|
|
|
|
END
|
|
|