WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/netinsight/NETI-ITS-MIB

2474 lines
81 KiB
Plaintext
Raw Blame History

NETI-ITS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Gauge32
FROM SNMPv2-SMI
RowPointer, RowStatus, TimeStamp, TruthValue, TEXTUAL-CONVENTION
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
netiExperimentalGeneric
FROM NETI-COMMON-MIB
Dsti
FROM NETI-CHMGR-MIB;
netiItsMIB MODULE-IDENTITY
LAST-UPDATED
"201409111300Z"
ORGANIZATION
"Net Insight AB"
CONTACT-INFO
"Net Insight AB
Box 42093
SE-126 14 Stockholm
Sweden
Tel +46-8-685 0400
info@netinsight.se"
DESCRIPTION
"Reference: NID757.
MIB for Isochronous Transport Services (ITS). ITS provides
transport of isochronous (time sensitive) traffic across the
DTM network in a transparent way. All the bits are
transported unmodified with preserved timing information.
The following services are all regarded as ITS:
- PDH primary rates
- Video (DVB/SD-SDI/HD-SDI)
- Audio (AES-EBU)
- SDH transport
The MIB includes three primary conceptual tables; for
configuring the trail termination points on the originating
(source) and terminating (sink) side of the connection, and
for configuring the interfaces.
The table itsSrcTtpTable defines the trail termination points
for the originating (source) side.
The table itsSnkTtpTable defines the trail termination points
for the terminating (sink) side.
The table itsIfTable defines the interfaces. In addition to
the itsIfTable, there are dedicated tables for technology
specific configuration objects.
The interconnection between the trail termination points
shall be done through configuration in the Channel Manager
MIB (NETI-CHMGR-MIB).
A bi-directional connections are handled by creating two
uni-directional connections, one in each direction, between
the trail termination points."
REVISION
"201409111300Z"
DESCRIPTION
"- Added object for setting maximum expected differential delay
on 1+1 protected transport, itsIfPs3MaxExpDifferentialDelay.
- Added setting to freeze output: freeze(3) to object
itsIfTxMuteOnFault."
REVISION
"201402211500Z"
DESCRIPTION
"- Objects for managing SDI timing delay has been changed:
itsIfSdiFsVDelay and itsIfSdiFsHDelay have been obsoleted,
and are replaced with itsIfSdiFsDealy.
- Added object for controlling audio transport on JPEG 2000
enabled interface, itsIfJ2kReduceAudioTransportBitrate."
REVISION
"201309300700Z"
DESCRIPTION
"- Added objects for managing SDI timing providers:
itsIfSdiIsTimingProvider, itsIfSdiFsVDelay and
itsIfSdiFsHDelay. Also added bits to itsIfCapabilities:
fs(15), avrs(16), dvrs(25).
- Updated itsIfJ2kSignalFormat. Renamed sdSdiPAL(1) to
sdSdi(1), and removed sdSdiNTSC(2). There is no
differentiation between PAL and NTSC."
REVISION
"201212031100Z"
DESCRIPTION
"- Added references from interface to TTPs, itsIfMembersSrc,
itsIfMembersSnk.
- Added objects for protection type 3 and hitless protection,
itsIfPs3Table."
REVISION
"201209041400Z"
DESCRIPTION
"- Added table for SDI interfaces, itsIfSdiTable. This table
contains objects for controlling autosense and presenting
video format.
- Corrected VBI index range to 1..46, itsIfSdiVbiIndex."
REVISION
"201201201600Z"
DESCRIPTION
"Clarified some object descriptions and the relation to JPEG 2000."
REVISION
"201112010900Z"
DESCRIPTION
"- Added new JPEG 2000 signal formats to itsIfJ2kSignalFormat.
- Added objects for presenting VBI, ANC and audio rate on
JPEG 2000 capable interfaces, itsIfJ2kRateVBI,
itsIfJ2kRateAnc, itsIfJ2kRateAudio.
- Added audio sample size to JPEG 2000 capable interfaces,
itsIfJ2kAudioSampleSize.
- Added table for VBI lines for SDI interfaces,
itsIfSdiVbiTable.
- Added table for ANC data for SDI interfaces,
itsIfSdiAncTable."
REVISION
"201110101300Z"
DESCRIPTION
"Extended support for JPEG 2000 interfaces, added:
- Added object to set signal format, itsIfJ2kSignalFormat.
- Added objects for presentation of video rate,
itsIfJ2kRateVideo, itsIfJ2kRateVideoMax.
- Added table to configure audio groups, itsIfSdiAudioTable."
REVISION
"201104270900Z"
DESCRIPTION
"This version of the MIB contains functionality that has not
yet been incorporated into the MAIN branch of NimOS.
This version of the MIB is a merge of:
- JPEG 2000 functionality
- AES (MADI) functionality."
REVISION
"201104270800Z"
DESCRIPTION
"Added basic support for JPEG 2000:
- Added table for JPEG 2000 interfaces, itsIfJ2kTable.
- Added j2kEnc(21) and j2kDec(22) to itsIfCapabilities."
REVISION
"201102041200Z"
DESCRIPTION
"Added table for AES interfaces, itsIfAesTable.
Added madi(19) and ref(20) to itsIfCapabilities."
REVISION
"201102030900Z"
DESCRIPTION
"The itsIfLoopTime is deprecated."
REVISION
"201008190900Z"
DESCRIPTION
"Added object itsSnkTtpPSAllow to itsSnkTtpTable.
Removed default value for object itsIfProperites."
REVISION
"201001190900Z"
DESCRIPTION
"Added object itsIfInterfaceType to itsIfTable.
Added table itsIfPdhTable dedicated for PDH interface
related configuration objects.
Added table itsIfMonTable dedicated for monitor interface
related configuration objects.
Added table itsIfSdhTable dedicated for SDH interface related
configuration objects.
Added table itsIfDvbTable dedicated for DVB interface related
configuration objects."
REVISION
"200901221500Z"
DESCRIPTION
"Added sdi2967(13) and sdi2970(14) to itsIfCapabilities.
Updated some descriptions.
Changed labels to sdi1483, sdi1485, sdi288 and sdi270 in
itsIfCapabilities to conform to SMIv2 (RFC2578).
Added itsSnkTtpTConnection2 for support of 1+1 protection
where two connections from two different trail termination
points (TTPs) are used, as opposed to two channels in the
same connection from a single TTP."
REVISION
"200804171030Z"
DESCRIPTION
"Added ttp(5), loopl(7), loopd(8), sdi-1483(9), sdi-1485(10),
sdi-288(11) and sdi-270(12) to itsIfCapabilities."
REVISION
"200801181500Z"
DESCRIPTION
"Added tables to lookup index for a TTP based on the DSTI:
itsSrcIndexLookupTable and itsSnkIndexLookupTable."
REVISION
"200712041600Z"
DESCRIPTION
"Added itsIfPurpose."
REVISION
"200706291400Z"
DESCRIPTION
"Changed label ais(2) to warning(2) for itsIfSuppressAlarm
and itsSnkTtpSuppressAlarm.
Added interfacePM(4) to itsIfCapabilities.
Added lod(4), rdi(5), lol(6) to itsIfDefects.
Added columnar object itsIfTxMuteOnFault.
Added notSupported(0) to itsIfLoopMode, itsIfSuppressAlarm
and itsSnkTtpSuppressAlarm.
Importing Gauge32.
Corrected typos."
::= { netiExperimentalGeneric 16 }
ItsTtpIndexList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A list of Integer32 values, where each 4 octets
represents one Integer32 value. Each value represents
an index into a table."
SYNTAX OCTET STRING (SIZE(0|4|8))
ItsProtectionStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Describes the protection status of a protected service.
unavailable(1). means that neither channel is up.
unprotected(2). means that one of the channels is up.
standbyProtected(3). means that both channels are up and if
the active channel detects AIS, a failover will occur while
incurring a hit.
hitlessCapable(4). means that the differential delay is
within limit, but a buffer reset is required to reach
hitless protected state. This can be achieved by writing the
forceHit parameter.
hitlessProtected(5). means that either channel can go down
without incurring a data loss."
SYNTAX INTEGER {
unavailable(1),
unprotected(2),
standbyProtected(3),
hitlessCapable(4),
hitlessProtected(5) }
--
-- Objects in the NETI-ITS-MIB
--
itsObjects OBJECT IDENTIFIER ::= { netiItsMIB 1 }
--
-- Groups in the NETI-ITS-MIB
--
itsIfGroup OBJECT IDENTIFIER ::= { itsObjects 1 }
itsSourceGroup OBJECT IDENTIFIER ::= { itsObjects 2 }
itsSinkGroup OBJECT IDENTIFIER ::= { itsObjects 3 }
--
-- The ITS interface group
--
itsIfLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime of the last change of any object in
the itsIfTable."
::= { itsIfGroup 1 }
-- Table with all interfaces
itsIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with all service interfaces that is detected by the
device. The table contains configuration objects common to
all types of interfaces."
::= { itsIfGroup 2 }
itsIfEntry OBJECT-TYPE
SYNTAX ItsIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One interface is represented by one conceptual row in the table.
Rx and Tx is always relative the application domain."
INDEX { itsIfIndex }
::= { itsIfTable 1 }
ItsIfEntry ::= SEQUENCE {
itsIfIndex Unsigned32,
itsIfIfIndex Integer32, -- same as ifIndex
itsIfName SnmpAdminString, -- same as ifName
itsIfDescr SnmpAdminString, -- same as ifDescr
itsIfSpeed Gauge32, -- same as ifSpeed
itsIfSuppressAlarm INTEGER,
itsIfLoopMode INTEGER,
itsIfLoopTime Gauge32, -- deprecated
itsIfCapabilities BITS,
itsIfProperties BITS,
itsIfDefects BITS,
itsIfFailure SnmpAdminString,
itsIfPMReference RowPointer,
itsIfOperStatus INTEGER, -- same as ifOperStatus
itsIfTxMuteOnFault INTEGER,
itsIfPurpose SnmpAdminString,
itsIfInterfaceType INTEGER,
itsIfMembersSrc ItsTtpIndexList,
itsIfMembersSnk ItsTtpIndexList
}
itsIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index in the table. The index is maintained across
re-boots. The index is a positive integer value."
::= { itsIfEntry 1 }
itsIfIfIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A reference to the index in the ifTable in the IF-MIB. If
this is not known, the value is 0."
::= { itsIfEntry 2 }
itsIfName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual name of the interface. The value of this object
should be the name of the interface as assigned by the local
device and should be suitable for use in commands entered at
the device's console. This might be a text name, such as
`e1-1:1' or a simple port number. This name would be the same
as presented by the object ifName in the ifXTable."
::= { itsIfEntry 3 }
itsIfDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string containing information about the interface.
This string should include the name of the manufacturer, the
product name and the version of the interface
hardware/software. This description would be the same as
presented by the object ifDescr in the ifTable."
::= { itsIfEntry 4 }
itsIfSpeed OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interface's capacity in bits per second. This value would
be the same as presented by the object ifSpeed in the
ifTable."
::= { itsIfEntry 5 }
itsIfSuppressAlarm OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
none(1),
warning(2),
all(3) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The alarm suppression mode. When alarms are suppressed, no
alarms will be generated if a fault situation is detected on
the interface. Failures will still be shown by the object
itsIfFailure.
notSupported(0). Suppress alarms is not supported by the
interface. This value can not be written.
none(1). No alarms are suppressed. All alarms are reported.
warning(2). Suppress alarms of severity warning only.
all(3). All alarms are suppressed. No alarms will be
reported."
DEFVAL { none }
::= { itsIfEntry 6 }
itsIfLoopMode OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
none(1),
line(2),
dtm(3) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Loop-back mode of the interface. When the loop-back mode is
changed to line(2) or dtm(3), a timer is initialized with the
value of itsIfLoopTime. The loop-back mode is reset to
none(1) when the timer runs out.
notSupported(0). Loopback is not supported by the
interface. This value can not be written.
none(1). The interface is not in loop-back mode. This is the
normal operation of the interface.
line(2). The interface is in loop-back mode on the line
side. Everything that is received on the Rx line interface is
looped back to the Tx line interface, and is also transmitted
to the remote node. Data received from the remote node is
ignored.
dtm(3). The interface is in loop-back mode on the DTM link
side. Everything that is received from the remote node is
looped back to the remote node, and is also output on the Tx
line interface. Data received on the Rx line interface is
ignored."
DEFVAL { none }
::= { itsIfEntry 7 }
itsIfLoopTime OBJECT-TYPE
SYNTAX Gauge32 (0..65535)
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Timer for the loop-back mode. The loop-back mode is reset to
its normal mode none(0) after the specified number of
seconds. A timer value of 0 indicates infinite time, which
means that the interface stays in loop-back mode until it is
specifically changed.
If the value of itsIfLoopTime is set while an interface is in
loop-back mode, the interface's timer will be reinitialized
with the new value."
DEFVAL { 0 }
::= { itsIfEntry 8 }
itsIfCapabilities OBJECT-TYPE
SYNTAX BITS {
multicast(0),
allowProtection(1),
requireCapacity(2),
channelPM(3),
interfacePM(4),
ttp(5),
mon(6),
loopl(7),
loopd(8),
sdi1483(9),
sdi1485(10),
sdi288(11),
sdi270(12),
sdi2967(13),
sdi2970(14),
fs(15),
avrs(16),
madi(19),
ref(20),
j2kEnc(21),
j2kDec(22),
hitps(23),
psType3(24),
dvrs(25),
compatible(31) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capabilities of the interface. The corresponding bit is set if
the capability is supported by the interface.
multicast(0). It is possible to use in multicast connection.
allowProtection(1). 1+1 protection on originating and
terminating side is supported.
requireCapacity(2). Management and setting of the connection
capacity is required. This is the case for e.g. an DVB
interface where the capacity may be set between 0.5 Mbps and
212.5 Mbps, but not for e.g. an SDI interface where the
capacity is fixed at 270 Mbps.
channelPM(3). Performance monitoring on the connection that
terminates on the TTP that uses the interface is supported.
interfacePM(4). Performance monitoring on the data received
on the interface is supported.
ttp(5). Allowed to be bound to a TTP.
mon(6). Monitoring port support.
loopl(7). Interface supports line loop-back. See itsIfLoopMode.
loopd(8). Interface supports DTM loop-back. See itsIfLoopMode.
sdi1483(9). Interface supports HD-SDI 1.485/1.001 Gbps.
sdi1485(10). Interface supports HD-SDI 1.485 Gbps.
sdi288(11). Interface supports 270 Mbps SD-SDI using a 288
Mbps channel.
sdi270(12). Interface supports 270 Mbps SD-SDI using a 270
Mbps channel.
sdi2967(13). Interface supports HD-SDI 2.970/1.001 Gbps.
sdi2970(14). Interface supports HD-SDI 2.970 Gbps.
fs(15). Interface supports frame synchronization.
avrs(16). Interface supports analog video reference signal.
madi(19). Interface supports MADI - AES10.
ref(20). Interface supports interface locking.
j2kEnc(21). Interface supports JPEG 2000 encoding.
j2kDec(22). Interface supports JPEG 2000 decoding.
hitps(23). Interface supports hitless 1+1 protection.
psType3(24). Interface supports protection model where two
sink trail termination points (TTP) per destination is used.
dvrs(25). Interface supports digital video reference signal.
compatible(31). The interface is compatible with older
systems, and is able to function in a connection where the
remote node is of older system release."
::= { itsIfEntry 9 }
itsIfProperties OBJECT-TYPE
SYNTAX BITS {
tbd(0) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Properties on the interface. A property can only be set if
the interface supports has the corresponding capability. The
capabilities of the interface can be determined by examine
itsIfCapabilities.
Currently, no properties are supported. The object exists
for support of future interfaces where configuration of the
interface properties are necessary."
::= { itsIfEntry 10 }
itsIfDefects OBJECT-TYPE
SYNTAX BITS {
los(0),
lof(1),
ais(2),
lop(3),
lod(4),
rdi(5),
lol(6)}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defects indicated on the interface since the last time the
object was read.
los(0) Loss of Signal was detected.
lof(1) Loss of Frame was detected.
ais(2). Alarm Indication Signal was received from up-stream
node.
lop(3). Loss of Pointer was detected. This happens on DVB
when the connection does not have enough capacity.
lod(4). Loss of Data (congestion) was detected.
rdi(5). Remote Defect Indication was detected.
lol(6). Loss of Lock (frequency outside range) was detected."
::= { itsIfEntry 11 }
itsIfFailure OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string describing a fault status on the
interface. The object presents an empty string if there are
no faults on the interface."
::= { itsIfEntry 12 }
itsIfPMReference OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A reference to an object that presents performance data
for the interface. The object is not part of this MIB."
::= { itsIfEntry 13 }
itsIfOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(4),
dormant(5),
notPresent(6) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational state of the interface. This is the same as
the object ifOperStatus in the ifTable.
up(1). The interface passes data and is used by a TTP.
down(2). The interface is down. If the administrative state
is up, the operational state is down only if there is a fault
situation that prevents the interface from not being down.
unknown(4). The state of the interface is unknown, possibly
due to some internal error.
dormant(5). The interface is ready, but is not used by any
TTP.
notPresent(6). The interface is not present. If a physical
port is represented by multiple interfaces (e.g. different
interfaces for DVB, SDI or monitoring), then if one of the
interfaces at a port is `up(1)', then the remaining
interfaces at the same port are unavailable for use and gets
operational state `notPresent(6)'"
::= { itsIfEntry 14 }
itsIfTxMuteOnFault OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
enable(1),
disable(2),
freeze(3) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the interface output in case of a fault.
notSupported(0). The interface does not support control of
transmitter on fault. This value can only be read, and can
never be written.
enable(1). Will turn off (mute) transmitter power on fault.
disable(2). Will output default signal on fault.
freeze(3). Freezes the output on signal fail. This is mainly
intended to be used with through timing mode. In aligned
mode, output is always freezed anyway regardless if this
value is set or not. Valid if `fs' bit is set in
itsIfCapabilities."
::= { itsIfEntry 15 }
itsIfPurpose OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A string presenting the purpose of the TTP that is actively
(trying) to use the interface. If no TTP is using the
interface, then the purpose is empty. If an interface can be
used as input and output interface at the same time (e.g. the
interface has two physical ports), then this object presents
the purpose of the TTP that originates in this interface."
DEFVAL { ''H }
::= { itsIfEntry 16 }
itsIfInterfaceType OBJECT-TYPE
SYNTAX INTEGER {
pdh(1),
sdh(2),
sdi(3),
dvb(4),
aes(5),
mon(6) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Denotes the type of interface."
::= { itsIfEntry 17 }
itsIfMembersSrc OBJECT-TYPE
SYNTAX ItsTtpIndexList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A list of values of the itsSrcTtpIndex for the source trail
termination points (TTPs) that are actively connected to
this interface. A TTP can only be connected to an
interface if its administrative state is `up'."
::= { itsIfEntry 18 }
itsIfMembersSnk OBJECT-TYPE
SYNTAX ItsTtpIndexList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A list of values of the itsSnkTtpIndex for the sink trail
termination points (TTPs) that are actively connected to
this interface. A TTP can only be connected to an
interface if its administrative state is `up'."
::= { itsIfEntry 19 }
-- Table with PDH interfaces
itsIfPdhTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfPdhEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with PDH interfaces. The table contains configuration
objects specific for PDH interfaces. The table is indexed using
the same index as the itsIfTable."
::= { itsIfGroup 3 }
itsIfPdhEntry OBJECT-TYPE
SYNTAX ItsIfPdhEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One PDH interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index."
INDEX { itsIfIndex }
::= { itsIfPdhTable 1 }
ItsIfPdhEntry ::= SEQUENCE {
itsIfPdhSignal INTEGER,
itsIfPdhFraming INTEGER
}
itsIfPdhSignal OBJECT-TYPE
SYNTAX INTEGER {
e3(1),
ds3(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects type of signal to transport, E3 or DS3."
DEFVAL { e3 }
::= { itsIfPdhEntry 1 }
itsIfPdhFraming OBJECT-TYPE
SYNTAX INTEGER {
none(1),
g751(2),
g832(3),
cbit(4),
m13(5) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects the type of framing to use. The valid values depend on
selection of type on `itsIfPdhType'.
none(1). No framing.
g751(2). Only valid for E3.
g832(3). Only valid for E3.
cbit(4). Only valid for DS3.
m13(5). Only valid for DS3."
DEFVAL { none }
::= { itsIfPdhEntry 2 }
-- Table with SDH interfaces
itsIfSdhTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfSdhEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with SDH interfaces. The table contains configuration
objects specific for SDH interfaces. The table is indexed using
the same index as the itsIfTable."
::= { itsIfGroup 4 }
itsIfSdhEntry OBJECT-TYPE
SYNTAX ItsIfSdhEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One SDH interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index."
INDEX { itsIfIndex }
::= { itsIfSdhTable 1 }
ItsIfSdhEntry ::= SEQUENCE {
itsIfSdhTiming INTEGER ,
itsIfSdhMode INTEGER,
itsIfSdhSs Unsigned32,
itsIfSdhS1 Unsigned32,
itsIfSdhSoh SnmpAdminString,
itsIfSdhPoh SnmpAdminString,
itsIfSdhJc SnmpAdminString
}
itsIfSdhTiming OBJECT-TYPE
SYNTAX INTEGER {
loop(1),
internal(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects timing mode for the interface, i.e. clock source in
transmission path."
DEFVAL { loop }
::= { itsIfSdhEntry 1 }
itsIfSdhMode OBJECT-TYPE
SYNTAX INTEGER {
sdh(1),
sonet(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Sets SDH or SONET interface mode."
DEFVAL { sdh }
::= { itsIfSdhEntry 2 }
itsIfSdhSs OBJECT-TYPE
SYNTAX Unsigned32 (0..3)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Payload mapping type."
DEFVAL { 2 }
::= { itsIfSdhEntry 3 }
itsIfSdhS1 OBJECT-TYPE
SYNTAX Unsigned32 (0..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Synchronization message to send to external equipment in
transmission path. This defines the quality level of the
clock used to transmit data."
DEFVAL { 15 }
::= { itsIfSdhEntry 4 }
itsIfSdhSoh OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A string containing the values of some section overhead
bytes. The byte values are on the format byte name, equal
sign, byte value. The values are then separated by a single
space character. I.e. the format is `S1=n SS=n M1=n B1=n
B2=n'."
::= { itsIfSdhEntry 5 }
itsIfSdhPoh OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A string containing the values of some path overhead bytes.
The byte values are on the format byte name, equal sign, byte
value. The values are then separated by a single space
character. I.e. the format is `B3=n G1=n G2=n'."
::= { itsIfSdhEntry 6 }
itsIfSdhJc OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A string containing the values of some justification
counters. The byte values are on the format counter name,
equal sign, byte value. The values are then separated by a
single space character. I.e. the format is `RPJE+=n RJE-=n
TPJE+= TPJE-=n FJE+=n FJE-=n'."
::= { itsIfSdhEntry 7 }
-- Table with DVB interfaces
itsIfDvbTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfDvbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with DVB interfaces. The table contains configuration
objects specific for DVB interfaces. The table is indexed using
the same index as the itsIfTable."
::= { itsIfGroup 5 }
itsIfDvbEntry OBJECT-TYPE
SYNTAX ItsIfDvbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One DVB interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index."
INDEX { itsIfIndex }
::= { itsIfDvbTable 1 }
ItsIfDvbEntry ::= SEQUENCE {
itsIfDvbFormat SnmpAdminString,
itsIfDvbOutputMode INTEGER
}
itsIfDvbFormat OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string in a non-formal format describing the format
of the data."
::= { itsIfDvbEntry 1 }
itsIfDvbOutputMode OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
burst(2),
spread(3) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects output mode."
DEFVAL { auto }
::= { itsIfDvbEntry 2 }
-- Table with AES/EBU interfaces
itsIfAesTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfAesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with AES interfaces. The table contains configuration
objects specific for AES interfaces. The table is indexed
using the same index as the itsIfTable."
::= { itsIfGroup 6 }
itsIfAesEntry OBJECT-TYPE
SYNTAX ItsIfAesEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One AES interface is represented by one conceptual row in the
table."
INDEX { itsIfIndex }
::= { itsIfAesTable 1 }
ItsIfAesEntry ::= SEQUENCE {
itsIfAesIsTimingProvider INTEGER,
itsIfAesReference Integer32
}
itsIfAesIsTimingProvider OBJECT-TYPE
SYNTAX INTEGER {
no(0),
wordClock(1) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects whether the interface will be used primarily as as
timing provider for other interfaces on the same board. This
object is applicable only if the interface supports reference
locking, i.e. if the `ref' bit is set in itsIfCapabilities.
no(0). Used primarily as normal transport interface and
secondarily as digital timing provider. Operational state is
non-dormant and alarms are raised only when ingress or egress
connection exists.
wordClock(1). Used primarily as 48 kHz word clock timing
provider. Neither ingress nor egress connections are
allowed. Operational state is non-dormant and alarms can be
raised if needed. "
DEFVAL { no }
::= { itsIfAesEntry 1 }
itsIfAesReference OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects the source interface to use as timing reference for
output alignment. The source can be any other interface on
the same board except itself. The value is the relative
interface number on the board, where the first interface on
the board is number 1, the second is number 2 and so on.
This object is applicable only if the interface supports
reference locking, i.e. if the `ref' bit is set in
itsIfCapabilities."
::= { itsIfAesEntry 2 }
-- Table with SDI interfaces
itsIfSdiTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfSdiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with SDI video interfaces. The table contains configuration
objects specific to SDI interfaces. The table is indexed using the
same index as the itsIfTable."
::= { itsIfGroup 7 }
itsIfSdiEntry OBJECT-TYPE
SYNTAX ItsIfSdiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One SDI interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index."
INDEX { itsIfIndex }
::= { itsIfSdiTable 1 }
ItsIfSdiEntry ::= SEQUENCE {
itsIfSdiFormat SnmpAdminString,
itsIfSdiAutoSense INTEGER,
itsIfSdiIsTimingProvider INTEGER,
itsIfSdiReference Integer32,
itsIfSdiFsVDelay Integer32, -- obsolete, use itsIfSdiFsDelay instead.
itsIfSdiFsHDelay Integer32, -- obsolete, use itsIfSdiFsDelay instead.
itsIfSdiFsDelay Integer32
}
itsIfSdiFormat OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Video source format. The format is presented as
`<pixels-per-line>x<lines-per-frame><i/p> @ <freq> Hz'
E.g. `1920x1080p @ 30 Hz'
The string is empty if no format is detected."
::= { itsIfSdiEntry 1 }
itsIfSdiAutoSense OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls whether autosense of the input/output signal shall
be enabled or not.
notSupported(0). The interface does not support autosense.
enable(1). Autosense is enabled. Input or output speed is
automatically detected and the interface speed will
automatically be configured to this detected speed regardless
of the configured capacity of the transport channel.
disable(2). Autosense is disabled. The interface is configured
to a speed in accordance with the capacity of the transported
channel."
::= { itsIfSdiEntry 2 }
itsIfSdiIsTimingProvider OBJECT-TYPE
SYNTAX INTEGER {
no(0),
analog(1),
digital(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects whether the interface will be used primarily as as
timing provider for other interfaces on the same board. This
object is applicable only if the interface supports analog
video reference signal, or digital video reference signal, i.e.
if any of the bits `avrs' or `dvrs' is set in
itsIfCapabilities.
no(0). Used primarily as normal transport interface and
secondarily as digital timing provider. Operational state is
non-dormant and alarms are raised only when ingress or egress
connection exists.
analog(1). Used primarily as analog timing provider. Neither
ingress nor egress connections are allowed. Operational
state is non-dormant and alarms can be raised as needed.
This value can only be set if the interface supports analog
video reference signal, i.e. the `avrs' bit is set in
itsIfCapabilities.
digital(1). Used primarily as digital timing provider and
secondarily as transport interface. Operational state is
non-dormant and alarms can be raised as needed regardless
if any ingress or egress connection exists. This value can
only be set if the interface supports digital video reference
signal, i.e. the `dvrs' bit is set in itsIfCapabilities."
DEFVAL { no }
::= { itsIfSdiEntry 3 }
itsIfSdiReference OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects the source interface to use as timing reference for
output alignment. The source can be any interface on the
same board. The value is the relative interface number on
the board, where the first interface on the board is number
1, the second is number 2 and so on. A value of `0' (zero)
indicates the node sync. The default is itself, which equals
to through timing. As through timing is not available on
JPEG 2000 decoder, selection of the interface itself means
node sync.
This object is applicable only if the interface supports
reference locking, i.e. if the `ref' bit is set in
itsIfCapabilities."
::= { itsIfSdiEntry 4 }
itsIfSdiFsVDelay OBJECT-TYPE
SYNTAX Integer32 (-3..1124)
MAX-ACCESS read-write
STATUS obsolete -- use itsIfSdiFsDelay instead.
DESCRIPTION
"Adjusts the vertical output delay in number of lines.
This object is applicable only if the interface supports
reference locking, i.e. if the `ref' bit is set in
itsIfCapabilities."
::= { itsIfSdiEntry 5 }
itsIfSdiFsHDelay OBJECT-TYPE
SYNTAX Integer32 (-3865..259)
MAX-ACCESS read-write
STATUS obsolete -- use itsIfSdiFsDelay instead.
DESCRIPTION
"Adjusts the horizontal output delay in number of pixels.
This object is applicable only if the interface supports
reference locking, i.e. if the `ref' bit is set in
itsIfCapabilities."
::= { itsIfSdiEntry 6 }
itsIfSdiFsDelay OBJECT-TYPE
SYNTAX Integer32 (-20854167..20854167)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Adjusts the output delay in number of nanoseconds.
This object is applicable only if the interface supports
reference locking, i.e. if the `ref' bit is set in
itsIfCapabilities."
::= { itsIfSdiEntry 7 }
-- Table with monitor interfaces
itsIfMonTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfMonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with monitor interfaces. The table contains
configuration objects specific for monitor interfaces. A
monitor interface is used for monitoring data on another
interface. It outputs the same data as the in- or output of
the interface that it is monitoring.
The table is indexed using the same index as the itsIfTable."
::= { itsIfGroup 9 }
itsIfMonEntry OBJECT-TYPE
SYNTAX ItsIfMonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One monitor port is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index."
INDEX { itsIfIndex }
::= { itsIfMonTable 1 }
ItsIfMonEntry ::= SEQUENCE {
itsIfMonMonitoredInterface Integer32,
itsIfMonDirection INTEGER,
itsIfEnableButton TruthValue
}
itsIfMonMonitoredInterface OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The relative number of the interface on the board that this
interface is selected to monitor. The first interface on the
board is number 1, the second is number 2 and so on. A value
of 0 denotes that no interface shall be monitored."
DEFVAL { 0 }
::= { itsIfMonEntry 1 }
itsIfMonDirection OBJECT-TYPE
SYNTAX INTEGER {
in(1),
out(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The direction of the monitored interface.
in(1). Monitors the input data of the monitored interface.
out(2). Monitors the output data of the monitored interface."
DEFVAL { in }
::= { itsIfMonEntry 2 }
itsIfEnableButton OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls if a `monitor' push button on the device front panel
is enabled for selection of interface to monitor. This
object is only applicable for boards supporting this
function."
DEFVAL { false }
::= { itsIfMonEntry 3 }
-- Table with JPEG 2000 interfaces
itsIfJ2kTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfJ2kEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with JPEG 2000 interfaces. The table contains
configuration objects specific for JPEG 2000 encoding and
decoding capable interfaces, i.e. when any of the bits
`j2kEnc' or `j2kDec' are set in `itsIfCapabilities'.
The table is indexed using the same index as the itsIfTable."
::= { itsIfGroup 10 }
itsIfJ2kEntry OBJECT-TYPE
SYNTAX ItsIfJ2kEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One JPEG 2000 capable interface is represented by one
conceptual row in the table. The interface is also
represented in the itsIfTable using the same index."
INDEX { itsIfIndex }
::= { itsIfJ2kTable 1 }
ItsIfJ2kEntry ::= SEQUENCE {
itsIfJ2kEncoderEnable TruthValue,
itsIfJ2kDecoderActive TruthValue,
itsIfJ2kSignalFormat INTEGER,
itsIfJ2kRateVideo Unsigned32,
itsIfJ2kRateVideoMax Unsigned32,
itsIfJ2kRateVbi Unsigned32,
itsIfJ2kRateAnc Unsigned32,
itsIfJ2kRateAudio Unsigned32,
itsIfJ2kAudioSampleSize Unsigned32,
itsIfJ2kReduceAudioTransportBitrate TruthValue
}
itsIfJ2kEncoderEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Selects whether the JPEG 2000 encoder functionality is
enabled of not for the interface. The rate of the JPEG 2000
stream is calculated from the channel capacity set in the
channel manager (NETI-CHMGR-MIB). This object cannot be
changed while there is an active connection on the interface.
Only an ingress interface can act as encoder."
DEFVAL { false }
::= { itsIfJ2kEntry 1 }
itsIfJ2kDecoderActive OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the JPEG 2000 decoder functionality is
active or not. The interface acting as JPEG 2000 decoder is
automatic. Only an egress interface can act as decoder."
::= { itsIfJ2kEntry 2 }
itsIfJ2kSignalFormat OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(0),
sdSdi(1),
hdSdiEu(3),
hdSdiUs(4),
hd3gSdiEu(5),
hd3gSdiUs(6) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates for which format JPEG 2000 is configured. The
choice of format affects the available VBI configuration, the
number of audio groups, and the configurable bandwidth range.
notApplicable(0). If the interface does not support JPEG 2000
encoding.
sdSdi(1). SD-SDI PAL/NTSC format.
hdSdiEu(3). HD-SDI European format.
hdSdiUs(4). HD-SDI American format.
hd3gSdiEu(5). 3G-SDI European format.
hd3gSdiUs(6). 3G-SDI American format."
::= { itsIfJ2kEntry 3 }
itsIfJ2kRateVideo OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual JPEG 2000 code stream bit rate. Applicable for
both encoder and decoder interfaces."
::= { itsIfJ2kEntry 4 }
itsIfJ2kRateVideoMax OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum JPEG 2000 code stream bit rate, calculated from
the channel capacity, ANC, audio and VBI configurations."
::= { itsIfJ2kEntry 5 }
itsIfJ2kRateVbi OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The VBI service bit rate detected and forwarded."
::= { itsIfJ2kEntry 6 }
itsIfJ2kRateAnc OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ancillary data bit rate detected and forwarded."
::= { itsIfJ2kEntry 7 }
itsIfJ2kRateAudio OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The audio bit rate detected and forwarded."
::= { itsIfJ2kEntry 8 }
itsIfJ2kAudioSampleSize OBJECT-TYPE
SYNTAX Unsigned32 (0|20|24)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of bits used for the audio samples: default 20-bit
audio or extended 24-bit audio. This value is applicable
only for SD-SDI signal format (PAL/NTSC), and only on source
interfaces. The value zero (0) indicates that it is not
applicable."
DEFVAL { 20 }
::= { itsIfJ2kEntry 9 }
itsIfJ2kReduceAudioTransportBitrate OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables or disables enhanced audio transport, using a reduced
transport bitrate for the audio. This is only applicable for
HD and 3G format, and only when the JPEG 2000 encodes is
enabled (`itsIfJ2KEncodedEnable')."
DEFVAL { false }
::= { itsIfJ2kEntry 10 }
-- Table with SDI audio groups
itsIfSdiAudioTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfSdiAudioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with audio groups. The table contains configuration
objects specific for audio groups in SDI streams. Each audio
group consists of 4 audio channels. Audio group 5-8 is
available only for 3G-SDI. The table is indexed per
interface and per audio group."
::= { itsIfGroup 11 }
itsIfSdiAudioEntry OBJECT-TYPE
SYNTAX ItsIfSdiAudioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One audio group is represented by one conceptual row in the
table. An entry may only exist for an interface that is
capable of JPEG 2000, i.e. when any of the bits `j2kEnc' or
`j2kDec' are set in `itsIfCapabilities'. The data is valid
only if the interface is enabled for JPEG 2000."
INDEX { itsIfIndex, itsIfSdiAudioIndex }
::= { itsIfSdiAudioTable 1 }
ItsIfSdiAudioEntry ::= SEQUENCE {
itsIfSdiAudioIndex Unsigned32,
itsIfSdiAudioForward TruthValue
}
itsIfSdiAudioIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index in the table. The index specifies the audio group
number. Index 5-8 is only available for 3G-SDI."
::= { itsIfSdiAudioEntry 1 }
itsIfSdiAudioForward OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the audio group is enabled for transmission
or not. Only applicable for source end interfaces."
DEFVAL { false }
::= { itsIfSdiAudioEntry 2 }
-- Table with VBI (Vertical Blanking Interval)
itsIfSdiVbiTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfSdiVbiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with Vertical Blanking Interval (VBI); lines outside
the actual picture that are used to forward data. The number
of lines in the VBI depends on the format of the SDI signal.
VBI is only used in SD signals (PAL/NTSC)."
::= { itsIfGroup 12 }
itsIfSdiVbiEntry OBJECT-TYPE
SYNTAX ItsIfSdiVbiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One entry per VBI line. An entry may only exist for an
interface that is capable of JPEG 2000, i.e. when any of the
bits `j2kEnc' or `j2kDec' are set in `itsIfCapabilities'.
The data is valid only if the interface is enabled for JPEG
2000."
INDEX { itsIfIndex, itsIfSdiVbiIndex }
::= { itsIfSdiVbiTable 1 }
ItsIfSdiVbiEntry ::= SEQUENCE {
itsIfSdiVbiIndex Integer32,
itsIfSdiVbiLineNumber Integer32,
itsIfSdiVbiForward INTEGER
}
itsIfSdiVbiIndex OBJECT-TYPE
SYNTAX Integer32 (1..46)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index in the table for the VBI line. This is not the
same as the line number."
::= { itsIfSdiVbiEntry 1 }
itsIfSdiVbiLineNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The line number."
::= { itsIfSdiVbiEntry 2 }
itsIfSdiVbiForward OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(0),
yes(1),
no(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the VBI line number is enabled for
forwarding or not. The value is applicable only for source
interfaces."
DEFVAL { yes }
::= { itsIfSdiVbiEntry 3 }
-- Table with ANC data (Ancillary data)
itsIfSdiAncTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfSdiAncEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with ancillary data. This is embedded into the SDI
signal but is not video."
::= { itsIfGroup 13 }
itsIfSdiAncEntry OBJECT-TYPE
SYNTAX ItsIfSdiAncEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One DID/SDID combination is represented by one conceptual row
in the table. An entry may only exist for an interface that
is capable of JPEG 2000, i.e. when any of the bits `j2kEnc'
or `j2kDec' are set in `itsIfCapabilities'. The data is
valid only if the interface is enabled for JPEG 2000."
INDEX { itsIfIndex, itsIfSdiAncIndex }
::= { itsIfSdiAncTable 1 }
ItsIfSdiAncEntry ::= SEQUENCE {
itsIfSdiAncIndex Integer32,
itsIfSdiAncDescription SnmpAdminString,
itsIfSdiAncDid Unsigned32,
itsIfSdiAncSdid Unsigned32,
itsIfSdiAncForward INTEGER
}
itsIfSdiAncIndex OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index in the table, with one row per DID/SDID combination."
::= { itsIfSdiAncEntry 1 }
itsIfSdiAncDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A string that identifies or describes the service
corresponding to the DID/SDID combination."
::= { itsIfSdiAncEntry 2 }
itsIfSdiAncDid OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Data ID. Identifies the type of ANC. If the value is
less than 0x08 then the ancillary data is of type 2, which
means that the SDID is also present and should be used."
::= { itsIfSdiAncEntry 3 }
itsIfSdiAncSdid OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Secondary Data ID. This has the value of 0 if the
ancillary data is of type 1."
::= { itsIfSdiAncEntry 4 }
itsIfSdiAncForward OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(0),
yes(1),
no(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates if the DID/SDID combination is enabled for
forwarding or not. The value is applicable only for source
interfaces."
DEFVAL { yes }
::= { itsIfSdiAncEntry 5 }
-- Table with protection type 3 settings
itsIfPs3Table OBJECT-TYPE
SYNTAX SEQUENCE OF ItsIfPs3Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with settings for hitless 1+1 protection."
::= { itsIfGroup 14 }
itsIfPs3Entry OBJECT-TYPE
SYNTAX ItsIfPs3Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One interface that is capable of hitless 1+1 protection is
represented by one row in this table. An entry may only
exist for an interface that is capable of switch type 3,
i.e. when the bits `hitps' or `psType3' is set in
`itsIfCapabilites'."
INDEX { itsIfIndex }
::= { itsIfPs3Table 1 }
ItsIfPs3Entry ::= SEQUENCE {
itsIfPs3DifferentialDelay Unsigned32,
itsIfPs3DifferentialDelayValid TruthValue,
itsIfPs3AheadInterface Integer32,
itsIfPs3HitlessProtection TruthValue,
itsIfPs3ProtectionStatus ItsProtectionStatus,
itsIfPs3ExpectedProtectionStatus ItsProtectionStatus,
itsIfPs3ForceHit Unsigned32,
itsIfPs3ActiveInterface Integer32,
itsIfPs3MaxExpDifferentialDelay Unsigned32
}
itsIfPs3DifferentialDelay OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured differential delay in microseconds between the two
paths. Zero (0) indicates that standby protection is used."
::= { itsIfPs3Entry 1 }
itsIfPs3DifferentialDelayValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies if the value of itsIfPs3DifferentialDelay is valid
or not."
::= { itsIfPs3Entry 2 }
itsIfPs3AheadInterface OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index of the sink trail termination point (TTP) that is
ahead. Minus one indicates either that information is not
available or is invalid."
::= { itsIfPs3Entry 3 }
itsIfPs3HitlessProtection OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies if hitless protection shall be attempted or not.
true(1). Will attempt to reach a hitless protection state.
false(2). Will only attempt to reach a standby protection
state."
::= { itsIfPs3Entry 4 }
itsIfPs3ProtectionStatus OBJECT-TYPE
SYNTAX ItsProtectionStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current protection state."
::= { itsIfPs3Entry 5 }
itsIfPs3ExpectedProtectionStatus OBJECT-TYPE
SYNTAX ItsProtectionStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The expected protection state. When the current protection
state (see itsIfPs3ProtectionStatus) is lower than the expected
protection state, an alarm is raised. The alarm is cleared
when the expected protection state is equal or higher than
the current protection state."
DEFVAL { unprotected }
::= { itsIfPs3Entry 6 }
itsIfPs3ForceHit OBJECT-TYPE
SYNTAX Unsigned32(0)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A write of zero (0) resets the buffers, and will therefore
minimize the the latency penalty incurred by the 1+1
buffering."
::= { itsIfPs3Entry 7 }
itsIfPs3ActiveInterface OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The index of the sink trail termination point (TTP) that is
is selected as source. Minus one indicates either that
information is not available or is invalid."
::= { itsIfPs3Entry 8 }
itsIfPs3MaxExpDifferentialDelay OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum expected differential delay in milliseconds where 0
(zero) implies largest possible value for channel capacity
and service type. If measured differential delay is above
this, hitless protected status can not be guaranteed.
Maximum assignable value is bit rate and service type
dependent. The higher the bit rate, the lower the value. For
largest bit rate however, up to 100 ms is guaranteed to work
for all service types.
Note also that the larger the value, the greater the latency.
Therefore, for latency sensitive signals as small non-zero
value as possible shall be used."
::= { itsIfPs3Entry 9 }
--
-- The source group
--
itsSrcTtpLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime of the last change of any object in
the itsSrcTtpTable."
::= { itsSourceGroup 1 }
itsSrcTtpNextIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the next available index for an entry in the
itsSrcTtpTable."
::= { itsSourceGroup 2 }
-- The Source TTP Table
itsSrcTtpTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsSrcTtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with source trail termination points."
::= { itsSourceGroup 3 }
itsSrcTtpEntry OBJECT-TYPE
SYNTAX ItsSrcTtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One conceptual row represents one source trail termination point."
INDEX { itsSrcTtpIndex }
::= { itsSrcTtpTable 1 }
ItsSrcTtpEntry ::= SEQUENCE {
itsSrcTtpIndex Unsigned32,
itsSrcTtpName SnmpAdminString,
itsSrcTtpCustomerId Unsigned32,
itsSrcTtpPurpose SnmpAdminString,
itsSrcTtpLocalIf Unsigned32,
itsSrcTtpLocalDsti Dsti,
itsSrcTtpMode INTEGER,
itsSrcTtpODescription Unsigned32,
itsSrcTtpOConnection Unsigned32,
itsSrcTtpFailure SnmpAdminString,
itsSrcTtpAdminStatus INTEGER,
itsSrcTtpOperStatus INTEGER,
itsSrcTtpRowStatus RowStatus
}
itsSrcTtpIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index in the table. The index is persistent cross reboots."
::= { itsSrcTtpEntry 1 }
itsSrcTtpName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual name of the trail termination point (TTP). The
value of this object should be the name of the TTP as
assigned by the local device and should be suitable for use
in commands entered at the device's console. This might be
a text name, such as `itso-1' or a simple port number."
::= { itsSrcTtpEntry 2 }
itsSrcTtpCustomerId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A customer identification number that represents the customer
or user of the trail termination point (TTP). The value could
be used e.g. for identifying the customer in Charge Data
Records. The value zero (0) represents that no customer is
associated with the TTP."
DEFVAL { 0 }
::= { itsSrcTtpEntry 3 }
itsSrcTtpPurpose OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A string describing the purpose of the TTP. The string is for
administrative use."
DEFVAL { ''H }
::= { itsSrcTtpEntry 4 }
itsSrcTtpLocalIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A reference to the local interface that shall be used by the
trail termination point (TTP). The value is representing the
index in the itsIfTable. The value must refers to an existing
entry in itsIfTable. When a TTP is created, the value of this
object points to an arbitrary interface in itsIfTable."
::= { itsSrcTtpEntry 5 }
itsSrcTtpLocalDsti OBJECT-TYPE
SYNTAX Dsti
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DSTI (DTM Service Type Instance) for the source trail
termination point. The value is used by the connection to
refer to this trail termination point. The DSTI must be unique
among the ITS source trail termination points."
::= { itsSrcTtpEntry 6 }
itsSrcTtpMode OBJECT-TYPE
SYNTAX INTEGER {
unicast(1),
multicast(2),
compatible(3) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The TTP mode. The associated interface, itsSrcTtpLocalIf,
must have the capability to support the property when the
administrative state of the TTP is set to up.
unicast(1). The trail termination point shall establish a
unicast connection.
multicast(2). The trail termination point shall established a
multicast connection. It will set the corresponding
capability in chmgrODescrCapabilites.
compatible(3). The trail termination point shall be
compatible with early systems releases, and is acting as to
connect to a remote system with an earlier system release."
DEFVAL { unicast }
::= { itsSrcTtpEntry 7 }
itsSrcTtpODescription OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A reference to the corresponding description of the
connection in the chmgrODescriptionTable in the Channel
Manager MIB (NETI-CHMGR-MIB). The value is the index into the
table, i.e. the value of chmgrODescrIndex. When a row
is created in or deleted from this table, the corresponding
row is created in or deleted from the table
chmgrODescriptionTable."
::= { itsSrcTtpEntry 8 }
itsSrcTtpOConnection OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A reference to the corresponding originating connection in
the table chmgrOConnectionTable in the Channel Manager MIB
(NETI-CHMGR-MIB). When an originating connection is
established from this trail termination point, an entry is
created in the table. The value is the index into that table,
i.e. the value of chmgrOConnIndex. If no connection is
established or associated with this connection, this is
indicated by a value of zero (0)."
::= { itsSrcTtpEntry 9 }
itsSrcTtpFailure OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string describing a fault status on the trail
termination point (TTP). A configuration error is regarded as
a fault state, which is indicated when the administrative
state is down. A network related fault can only occur when
the administrative state is up. The object presents an empty
string if there are no faults on the TTP."
::= { itsSrcTtpEntry 10 }
itsSrcTtpAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative state of the connection. The value
controls the desired state of the connection from the trail
termination point (TTP). Note that the associated interface
must have capabilities that matches the properties of the
TTP to be able to successfully change the administrative
state to up(1).
up(1). The connection shall be active.
down(2). The connection shall be in-active. The active
connection is torn down and alarms are cleared."
DEFVAL { down }
::= { itsSrcTtpEntry 11 }
itsSrcTtpOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(4),
dormant(5),
partial(9) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational state of the trail termination point (TTP).
up(1). The TTP is up and a connection is established to all
destinations. If the connection is 1+1 protected, both the
channels are established to all the destinations.
down(2). The connection is down to all destinations. The
itsSrcTtpFailure describes the fault.
unknown(4). The TTP is in an unknown state due to some
internal error.
dormant(5). The TTP is ready and is waiting for a connection
to be established.
partial(9). The connection is established to some but not all
the destinations. Or, if the connection is 1+1 protected,
only one of the channels are established."
::= { itsSrcTtpEntry 12 }
itsSrcTtpRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"See SNMPv2-TC. Use itsSrcTtpAdminStatus to activate and
de-activate a connection. The following values are supported:
active(1). The object always reads active.
createAndGo(4). A new conceptual row is created representing
a new trail termination point (TTP). To activate the TTP, set
the administrative status to up(1), after all columnar
objects have been updated. It is only possible to create
a TTP if at least one interface exists.
destroy(6). The connection is terminated and the TTP is
deleted."
::= { itsSrcTtpEntry 13 }
-- End of the Source TTP Table
-- The DSTI to Index Lookup Table for Source TTP's
itsSrcIndexLookupTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsSrcIndexLookupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table to lookup a DSTI to an index in the itsSrcTtpTable."
::= { itsSourceGroup 4 }
itsSrcIndexLookupEntry OBJECT-TYPE
SYNTAX ItsSrcIndexLookupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One conceptual row represents one lookup entry."
INDEX { itsSrcTtpLocalDsti }
::= { itsSrcIndexLookupTable 1 }
ItsSrcIndexLookupEntry ::= SEQUENCE {
itsSrcIndexLookupIndex Unsigned32
}
itsSrcIndexLookupIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value refers to the index in table itsSrcTtpTable."
::= { itsSrcIndexLookupEntry 1 }
-- End of the DSTI to Index Lookup Table for Source TTP's
--
-- The sink group
--
itsSnkTtpLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime of the last change of any object in
the itsSnkTtpTable."
::= { itsSinkGroup 1 }
itsSnkTtpNextIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the next available index for an entry in the
itsSnkTtpTable."
::= { itsSinkGroup 2 }
-- The Sink TTP Table
itsSnkTtpTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsSnkTtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table with sink trail termination points."
::= { itsSinkGroup 3 }
itsSnkTtpEntry OBJECT-TYPE
SYNTAX ItsSnkTtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One conceptual row represents one sink trail termination point."
INDEX { itsSnkTtpIndex }
::= { itsSnkTtpTable 1 }
ItsSnkTtpEntry ::= SEQUENCE {
itsSnkTtpIndex Unsigned32,
itsSnkTtpName SnmpAdminString,
itsSnkTtpCustomerId Unsigned32,
itsSnkTtpPurpose SnmpAdminString,
itsSnkTtpLocalIf Unsigned32,
itsSnkTtpLocalDsti Dsti,
itsSnkTtpPSActiveChannel INTEGER,
itsSnkTtpSuppressAlarm INTEGER,
itsSnkTtpTConnection Unsigned32,
itsSnkTtpDefects BITS,
itsSnkTtpFailure SnmpAdminString,
itsSnkTtpPMReference RowPointer,
itsSnkTtpAdminStatus INTEGER,
itsSnkTtpOperStatus INTEGER,
itsSnkTtpRowStatus RowStatus,
itsSnkTtpTConnection2 Integer32,
itsSnkTtpPSAllow TruthValue
}
itsSnkTtpIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index in the table. The index is persistent across reboots."
::= { itsSnkTtpEntry 1 }
itsSnkTtpName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The textual name of the trail termination point (TTP). The
value of this object should be the name of the TTP as
assigned by the local device and should be suitable for use
in commands entered at the device's console. This might be
a text name, such as `itsi-1' or a simple port number."
::= { itsSnkTtpEntry 2 }
itsSnkTtpCustomerId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A customer identification number that represents the customer
or user of the trail termination point (TTP). The value could
be used e.g. for identifying the customer in Charge Data
Records. The value zero (0) represents that no customer is
associated with the TTP."
DEFVAL { 0 }
::= { itsSnkTtpEntry 3 }
itsSnkTtpPurpose OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A string describing the purpose of the TTP. The object use is
for administrative purpose."
DEFVAL { ''H }
::= { itsSnkTtpEntry 4 }
itsSnkTtpLocalIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A reference to the local interface that shall be used by the
trail termination point (TTP). The value is representing the
index in the itsIfTable. The value must point to an existing
interface. When the TTP is created, the object points to an
arbitrary interface in itsIfTable."
::= { itsSnkTtpEntry 5 }
itsSnkTtpLocalDsti OBJECT-TYPE
SYNTAX Dsti
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DSTI (DTM Service Type Instance) for the sink trail
termination point. The value is used by the connection to
refer to this trail termination point. The DSTI must be
unique among the ITS sink trail termination points."
::= { itsSnkTtpEntry 6 }
itsSnkTtpPSActiveChannel OBJECT-TYPE
SYNTAX INTEGER {
primary(1),
secondary(2),
none(3) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The channel to use on a 1+1 protected connection. When a
connection is being established, the first established
channel will become the active channel. The device will
switch to the other channel when it detects a fault on the
active channel.
The value of this object cannot be changed unless the
operational state of the trail termination point is up.
primary(1). The primary channel is used. If 1+1 protection
switch is not used or supported, the primary channel is the
only channel, and the object cannot be set to any other
value.
secondary(2). The secondary channel is used.
none(3). The connection is not established, or is not 1+1
protected. It is not possible to set this value. While the
value is none(3), it is not possible to set this object."
::= { itsSnkTtpEntry 7 }
itsSnkTtpSuppressAlarm OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
none(1),
warning(2),
all(3) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The alarm suppression mode. When alarms are suppressed, no
alarms will be generated if a fault situation is detected on
the trail termination point (TTP). Failures will still be
shown by the object itsSnkTtpFailure.
notSupported(0). Suppress alarms is not supported by the
interface. This value can not be written.
none(1). No alarms are suppressed. All alarms are reported.
warning(2). Suppress alarms of severity warning only.
all(3). All transmission alarms are suppressed."
DEFVAL { none }
::= { itsSnkTtpEntry 8 }
itsSnkTtpTConnection OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A reference to the corresponding terminating connection in
the table chmgrTConnectionTable in the Channel Manager MIB
(NETI-CHMGR-MIB). The value is the index into that table,
i.e. the value of chmgrTConnIndex.
If 1+1 protection is used, then this object refers to the
first established connection. If two channels originate from
the same TTP, then the same connection is used for both
channels, which are referenced by this object. If two
channels originate from different TTPs, then two connections
are used, one for each channel. The second connected
connection is referenced by itsSnkTtpTConnection2."
::= { itsSnkTtpEntry 9 }
itsSnkTtpDefects OBJECT-TYPE
SYNTAX BITS {
los(0),
lof(1),
ais(2),
lop(3)}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defects indicated on the trail termination point since the
last time the object was read.
los(0) Loss of Signal was detected.
lof(1) Loss of Frame was detected.
ais(2). Alarm Indication Signal was received from originating
node.
lop(3). Loss of Pointer was detected. This happens on DVB
when the connection does not have enough capacity."
::= { itsSnkTtpEntry 10 }
itsSnkTtpFailure OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string describing a fault status on the trail
termination point (TTP). A configuration error is regarded as
a fault state, which is indicated when the administrative
state is down. A network related fault can only occur when
the administrative state is up. The object presents an empty
string if there are no faults on the TTP."
::= { itsSnkTtpEntry 11 }
itsSnkTtpPMReference OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A reference to an object that presents performance data for
the trail termination point. The object is not part of this
MIB. If the selected local interface (itsSnkLocalIf) does not
support performance monitoring for the TTP, it is indicated
by the value `0.0'."
::= { itsSnkTtpEntry 12 }
itsSnkTtpAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative state of the connection. The value
controls the desired state of the connection from the trail
termination point (TTP).
up(1). The connection shall be active.
down(2). The connection shall be in-active; active connection
are torn down and alarms are cleared. This is the required
state when changing the configuration of the TTP."
DEFVAL { down }
::= { itsSnkTtpEntry 13 }
itsSnkTtpOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
dormant(5) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational state of the trail termination point (TTP).
up(1). The TTP is up and a connection is established to all
destinations.
down(2). The connection is down to all destinations.
dormant(5). The TTP is ready and is waiting for a connection
to be established."
::= { itsSnkTtpEntry 14 }
itsSnkTtpRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"See SNMPv2-TC. Use itsSnkTtpAdminStatus to activate and
de-activate a connection. The following values are supported:
active(1). The object always reads active.
createAndGo(4). A new conceptual row is created representing
a new trail termination point (TTP). To activate the TTP, set
the administrative status to up(1), after all columnar
objects have been updated. It is only possible to crate a
TTP when at least one interface exists.
destroy(6). The connection is terminated and the TTP is
deleted."
::= { itsSnkTtpEntry 15 }
itsSnkTtpTConnection2 OBJECT-TYPE
SYNTAX Integer32 (-1|0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A reference to the corresponding terminating connection in
the table chmgrTConnectionTable in the Channel Manager MIB
(NETI-CHMGR-MIB) for the second established connection when 1+1
protection is used where the two channel originate from two
different trail termination points (TTPs). If the two
channels originate from the same TTP, then only one entry is
used in the chmgrTConnectionTable, referenced by
itsSnkTtpTConnection, and the value of this object is then
-1.
The value is the index into the table, i.e. the value of
chmgrTConnIndex."
::= { itsSnkTtpEntry 16 }
itsSnkTtpPSAllow OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls if termination of an 1+1 is allowed:
true(1). Allows termination of two channels or connections
for a 1+1 protected service.
false(2). Denies termination of a second channel or
connection. This prevents 1+1 protection."
DEFVAL { true }
::= { itsSnkTtpEntry 17 }
-- End of the Sink TTP Table
-- The DSTI to Index Lookup Table for Sink TTP's
itsSnkIndexLookupTable OBJECT-TYPE
SYNTAX SEQUENCE OF ItsSnkIndexLookupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table to lookup a DSTI to an index in the itsSnkTtpTable."
::= { itsSinkGroup 4 }
itsSnkIndexLookupEntry OBJECT-TYPE
SYNTAX ItsSnkIndexLookupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One conceptual row represents one lookup entry."
INDEX { itsSnkTtpLocalDsti }
::= { itsSnkIndexLookupTable 1 }
ItsSnkIndexLookupEntry ::= SEQUENCE {
itsSnkIndexLookupIndex Unsigned32
}
itsSnkIndexLookupIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value refers to the index in table itsSnkTtpTable."
::= { itsSnkIndexLookupEntry 1 }
-- End of the DSTI to Index Lookup Table for Sink TTP's
END
View Git Blame Copy Permalink