WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/bintec/BIANCA-BRICK-ATM2-MIB

1833 lines
50 KiB
Plaintext
Raw Blame History

-- This file is corresponding to Release 9.1.10.101 from 2014/08/11 00:00:00
-- (C)opyright 1991-2014 bintec elmeg GmbH, All Rights Reserved
-- $RCSfile: mibatm2,v $
-- $Revision: 1.32.1.1 $
BIANCA-BRICK-ATM2-MIB DEFINITIONS ::= BEGIN
IMPORTS
IpAddress, Counter, Gauge, TimeTicks, enterprises
FROM RFC1155-SMI
DisplayString
FROM RFC1158-MIB
PhysAddress
FROM RFC1213-MIB
OBJECT-TYPE
FROM RFC-1212;
bintec OBJECT IDENTIFIER ::= { enterprises 272 }
bibo OBJECT IDENTIFIER ::= { bintec 4 }
atm OBJECT IDENTIFIER
::= { bibo 16 }
---
--- ATM Interface Table
---
atmIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmIfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The atmIfTable displays all available ATM capable interfaces."
::= { atm 10 }
atmIfEntry OBJECT-TYPE
SYNTAX AtmIfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An interface entry containing objects at the
subnetwork layer and below for a particular
interface."
INDEX { atmIfIndex }
::= { atmIfTable 1 }
AtmIfEntry ::=
SEQUENCE {
atmIfIndex INTEGER,
atmIfType INTEGER,
atmIfDescr DisplayString,
atmIfAdminStatus INTEGER,
atmIfOperStatus INTEGER,
atmIfLastChange TimeTicks,
atmIfInPkts Counter,
atmIfOutPkts Counter,
atmIfRxSpeed Gauge,
atmIfTxSpeed Gauge,
atmIfInOctets Counter,
atmIfInDiscards Counter,
atmIfInErrors Counter,
atmIfOutOctets Counter,
atmIfOutDiscards Counter,
atmIfOutErrors Counter,
atmIfMaxTxRate INTEGER,
atmIfOperMode INTEGER
}
atmIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The interface index of the associated ATM hardware."
::= { atmIfEntry 1 }
atmIfType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
adsl(2),
shdsl(3),
vdsl(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object contains an interface type."
DEFVAL { other }
::= { atmIfEntry 2 }
atmIfDescr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Short description for this object."
::= { atmIfEntry 3 }
atmIfAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the desired state of the ATM interface."
DEFVAL { up }
::= { atmIfEntry 4 }
atmIfOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current operational state of the ATM interface."
DEFVAL { down }
::= { atmIfEntry 5 }
atmIfLastChange OBJECT-TYPE
SYNTAX
TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The value of sysUpTime at the time the interface entered
its current operational state. If the current state was
entered prior to the last re-initialization of the local
network management subsystem, then this object contains a
zero value."
::= { atmIfEntry 6 }
atmIfMaxTxRate OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object enables traffic shaping on the related ATM
interface. If set to zero (0) there is no shaping active.
Otherwise this variable defines the maximum amount of bits
per second to be transmitted. Note that the maximum transmit
rate is also determined by the capabilities of the ATM
hardware."
DEFVAL { 0 }
::= { atmIfEntry 7 }
atmIfOperMode OBJECT-TYPE
SYNTAX INTEGER {
atm(1),
efm(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current operational mode of the ATM interface.
The value atm(1) means ATM is used on the line.
The value efm(2) means ATM is used only internally
and Ethernet with HDLC framing is used on the line."
DEFVAL { atm }
::= { atmIfEntry 8 }
atmIfInPkts OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of reassembled received packets."
::= { atmIfEntry 22 }
atmIfOutPkts OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This number of transmitted packets."
::= { atmIfEntry 23 }
atmIfRxSpeed OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object contains the receive interface speed."
::= { atmIfEntry 24 }
atmIfTxSpeed OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object contains the transmit interface speed."
::= { atmIfEntry 25 }
atmIfInOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of octets received on the interface,
including framing characters."
::= { atmIfEntry 26 }
atmIfInDiscards OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of inbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being deliverable to a higher-layer protocol. One
possible reason for discarding such a packet could be to
free up buffer space."
::= { atmIfEntry 27 }
atmIfInErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of inbound packets that contained errors preventing
them from being deliverable to a higher-layer protocol."
::= { atmIfEntry 28 }
atmIfOutOctets OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of octets transmitted out of the interface,
including framing characters."
::= { atmIfEntry 29 }
atmIfOutDiscards OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of outbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being transmitted. One possible reason for discarding
such a packet could be to free up buffer space."
::= { atmIfEntry 30 }
atmIfOutErrors OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of outbound packets that could not be transmitted
because of errors."
::= { atmIfEntry 31 }
---
--- The Virtual Path Group
--- This group is mandatory for all UNI devices.
--- Information concerning Virtual Path Connections
--- This is the lite version of ATM-FORUM-MIB
---
atmVpcTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVpcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of status and parameter information on the virtual
path connections which cross this UNI. There is one entry in
this table for each permanent virtual path connection.
This is the lite version of ATM-FORUM-MIB DEFINITIONS "
::= { atm 11 }
atmVpcEntry OBJECT-TYPE
SYNTAX AtmVpcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about a
particular virtual path connection."
INDEX { atmVpcPortIndex, atmVpcVpi }
::= { atmVpcTable 1 }
AtmVpcEntry ::=
SEQUENCE {
atmVpcPortIndex INTEGER,
atmVpcVpi INTEGER,
atmVpcOperStatus INTEGER
}
atmVpcPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The interface index of the associated ATM hardware."
::= { atmVpcEntry 1 }
atmVpcVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Path Connection."
::= { atmVpcEntry 2 }
atmVpcOperStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
end2endUp(2),
end2endDown(3),
localUpEnd2endUnknown(4),
localDown(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present actual operational status of the VPC. A value of
end2endUp(2) or end2endDown(3) would be used if the end-to-end
status is known. If only local status information is available,
a value of localUpEnd2endUnknown(4) or localDown(5) would
be used."
DEFVAL { unknown }
::= { atmVpcEntry 3 }
---
--- The Virtual Channel Group
--- This group is mandatory for all UNI devices.
--- Information concerning Virtual Channel Connections
--- This is the lite version of ATM-FORUM-MIB
---
atmVccTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVccEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A table of status and parameter information on the virtual
channel connections which are visible at this UNI. There is
one entry in this table for each permanent virtual channel
connection, including reserved VCCs that are supported;
e.g., signalling, OAM flows, and ILMI, but not unassigned
cells. This is the lite version of ATM-FORUM-MIB DEFINITIONS "
::= { atm 12 }
atmVccEntry OBJECT-TYPE
SYNTAX AtmVccEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing information about a
particular virtual channel connection."
INDEX { atmVccPortIndex, atmVccVpi, atmVccVci }
::= { atmVccTable 1 }
AtmVccEntry ::=
SEQUENCE {
atmVccPortIndex INTEGER,
atmVccVpi INTEGER,
atmVccVci INTEGER,
atmVccOperStatus INTEGER
}
atmVccPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The interface index of the associated ATM hardware."
::= { atmVccEntry 1 }
atmVccVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Channel Connection."
::= { atmVccEntry 2 }
atmVccVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection."
::= { atmVccEntry 3 }
atmVccOperStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
end2endUp(2),
end2endDown(3),
localUpEnd2endUnknown(4),
localDown(5)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The present actual operational status of the VCC. A value
of end2endUp(2) or end2endUp(3) is used if the end-to-end
status is known. If only local status is known a value of
localUpEnd2endUnknown(4) or localDown(5) is used."
DEFVAL { unknown }
::= { atmVccEntry 4 }
---
--- OAM configuration table
---
atmOamTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmOamEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This tables contains all OAM configuration parameters."
::= { atm 13 }
atmOamEntry OBJECT-TYPE
SYNTAX AtmOamEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { atmOamAtmIfIndex, atmOamVpi, atmOamVci }
::= { atmOamTable 1 }
AtmOamEntry ::=
SEQUENCE {
atmOamAtmIfIndex INTEGER,
atmOamVpi INTEGER,
atmOamVci INTEGER,
atmOamFlowLevel INTEGER,
atmOamLoopbackEnd2End INTEGER,
atmOamLoopbackSegment INTEGER,
atmOamLoopbackEnd2EndInterval INTEGER,
atmOamLoopbackSegmentInterval INTEGER,
atmOamLoopbackEnd2EndMaxPending INTEGER,
atmOamLoopbackSegmentMaxPending INTEGER,
atmOamCCEnd2EndActivation INTEGER,
atmOamCCSegmentActivation INTEGER,
atmOamCCEnd2EndDirection INTEGER,
atmOamCCSegmentDirection INTEGER
}
atmOamAtmIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The interface index of the associated ATM hardware."
::= { atmOamEntry 1 }
atmOamVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Path/Channel Connection."
DEFVAL { 8 }
::= { atmOamEntry 2 }
atmOamVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection."
DEFVAL { 32 }
::= { atmOamEntry 3 }
atmOamFlowLevel OBJECT-TYPE
SYNTAX INTEGER {
f5(1),
f4(2),
delete(10)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The OAM hierarchical flow levels : VC (F5) or VP (F4)."
DEFVAL { f5 }
::= { atmOamEntry 4 }
atmOamLoopbackEnd2End OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
enabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Indicates wether OAM loopback is enabled onto the end-to-end
connection."
DEFVAL { disabled }
::= { atmOamEntry 5 }
atmOamLoopbackSegment OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
enabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Indicates wether active OAM loopback is enabled onto the
segment connection."
DEFVAL { disabled }
::= { atmOamEntry 6 }
atmOamLoopbackEnd2EndInterval OBJECT-TYPE
SYNTAX INTEGER (0..999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"OAM loopback transmit interval (in seconds) for end-to-end
context."
DEFVAL { 5 }
::= { atmOamEntry 7 }
atmOamLoopbackSegmentInterval OBJECT-TYPE
SYNTAX INTEGER (0..999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"OAM loopback transmit interval (in seconds) for segment
context."
DEFVAL { 5 }
::= { atmOamEntry 8 }
atmOamLoopbackEnd2EndMaxPending OBJECT-TYPE
SYNTAX INTEGER (0..999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies the maximum number of outstanding OAM loopback
responses after which the associated F4/F5 instance will
be set into the end-to-end operational down status."
DEFVAL { 5 }
::= { atmOamEntry 9 }
atmOamLoopbackSegmentMaxPending OBJECT-TYPE
SYNTAX INTEGER (0..999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies the maximum number of outstanding OAM loopback
responses after which the associated F4/F5 instance will
be set into the segment operational down status."
DEFVAL { 5 }
::= { atmOamEntry 10 }
atmOamCCEnd2EndActivation OBJECT-TYPE
SYNTAX INTEGER {
passive(1),
active(2),
both(3),
no-negotiation(4),
none(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Determines wether OAM continuity check activation request
will be activated and/or accepted for the associated
end-to-end connection.
If set to passive(1) or both(3) CC activation requests
will be confirmed. If set to active(2) or both CC will
be requested. If set to no-negotiation(4) - depending on
the settings in atmOamCCEnd2EndDirection - CC cells will
be send and/or expected periodically without any previous
CC activation negotiation. If set to none(5) neither
CC activation will be requested/confirmed nor any CC
cells will be generated/expected."
DEFVAL { passive }
::= { atmOamEntry 11 }
atmOamCCSegmentActivation OBJECT-TYPE
SYNTAX INTEGER {
passive(1),
active(2),
both(3),
no-negotiation(4),
none(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Determines wether OAM continuity check activation request
will be activated and/or accepted for the associated
segment connection.
If set to passive(1) or both(3) CC activation requests
will be confirmed. If set to active(2) or both CC will
be requested. If set to no-negotiation(4) - depending on
the settings in atmOamCCSegmentDirection - CC cells will
be send and/or expected periodically without any previous
CC activation negotiation. If set to none(5) neither
CC activation will be requested/confirmed nor any CC
cells will be generated/expected."
DEFVAL { passive }
::= { atmOamEntry 12 }
atmOamCCEnd2EndDirection OBJECT-TYPE
SYNTAX INTEGER {
sink(1),
source(2),
both(3),
none(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Determines OAM continuity check direction (for end-to-end).
If set to sink(1) CC cells will be received only, if set to
source(2) CC cells will be generated periodically, if set to
both(3) CC cells will be received from the source as well
as send to the sink."
DEFVAL { both }
::= { atmOamEntry 13 }
atmOamCCSegmentDirection OBJECT-TYPE
SYNTAX INTEGER {
sink(1),
source(2),
both(3),
none(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Determines OAM continuity check direction (for segment).
If set to sink(1) CC cells will be received only, if set to
source(2) CC cells will be generated periodically, if set to
both(3) CC cells will be received from the source as well
as send to the sink."
DEFVAL { both }
::= { atmOamEntry 14 }
---
--- OAM statistics table
---
atmOamStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmOamStatEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This tables displays all used VCs."
::= { atm 14 }
atmOamStatEntry OBJECT-TYPE
SYNTAX AtmOamStatEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { atmOamStatAtmIfIndex, atmOamStatVpi, atmOamStatVci }
::= { atmOamStatTable 1 }
AtmOamStatEntry ::=
SEQUENCE {
atmOamStatAtmIfIndex INTEGER,
atmOamStatVpi INTEGER,
atmOamStatVci INTEGER,
atmOamStatFlowType INTEGER,
atmOamStatLoopbackTxCells Counter,
atmOamStatLoopbackRxCells Counter,
atmOamStatLoopbackPending Counter,
atmOamStatLoopbackCorr INTEGER,
atmOamStatAisState INTEGER,
atmOamStatAisTxCells Counter,
atmOamStatAisRxCells Counter,
atmOamStatTotalAisTxCells Counter,
atmOamStatTotalAisRxCells Counter,
atmOamStatRdiState INTEGER,
atmOamStatRdiTxCells Counter,
atmOamStatRdiRxCells Counter,
atmOamStatTotalRdiTxCells Counter,
atmOamStatTotalRdiRxCells Counter,
atmOamStatCCActivatorState INTEGER,
atmOamStatCCActivatorDirection INTEGER,
atmOamStatCCActivatorCorr INTEGER,
atmOamStatCCResponderState INTEGER,
atmOamStatCCResponderDirection INTEGER,
atmOamStatCCResponderCorr INTEGER,
atmOamStatCCTxCells Counter,
atmOamStatCCRxCells Counter
}
atmOamStatAtmIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The interface index of the associated ATM hardware."
::= { atmOamStatEntry 1 }
atmOamStatVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Path Connection."
::= { atmOamStatEntry 2 }
atmOamStatVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection."
::= { atmOamStatEntry 3 }
atmOamStatFlowType OBJECT-TYPE
SYNTAX INTEGER {
f5-segment(1),
f5-end2end(2),
f4-segment(3),
f4-end2end(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The OAM hierarchical flow levels: see ITU I.610"
DEFVAL { f5-end2end }
::= { atmOamStatEntry 4 }
atmOamStatLoopbackTxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM loopback cells that have been sent
to the target in this sequence."
::= { atmOamStatEntry 6 }
atmOamStatLoopbackRxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM loopback cells that have been received
from the target in this sequence."
::= { atmOamStatEntry 7 }
atmOamStatLoopbackPending OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of currently outstanding OAM loopback responses."
::= { atmOamStatEntry 8 }
atmOamStatLoopbackCorr OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The correlation of the last sent loopback message."
::= { atmOamStatEntry 9 }
atmOamStatAisState OBJECT-TYPE
SYNTAX INTEGER { off(1), on(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The AIS state is set to on(2) after receiving an AIS cell
or detection of LOC (Loss of Continuity). The Ais state is
set to off(1) either when receiving user cells
(same VCC context) or via timeout."
DEFVAL { off }
::= { atmOamStatEntry 10 }
atmOamStatAisTxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM alarm indication signal (AIS) cells
that have been transmitted since last change of AisState."
::= { atmOamStatEntry 11 }
atmOamStatAisRxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM alarm indication signal (AIS) cells
that have been received since last change of AisState."
::= { atmOamStatEntry 12 }
atmOamStatTotalAisTxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of OAM alarm indication signal (AIS) cells
that have been transmitted."
::= { atmOamStatEntry 13 }
atmOamStatTotalAisRxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of OAM alarm indication signal (AIS) cells
that have been received."
::= { atmOamStatEntry 14 }
atmOamStatRdiState OBJECT-TYPE
SYNTAX INTEGER { off(1), on(2) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The RDI state is set to on(2) after receiving a RDI cell.
The RDI state is to off(1) via timeout."
DEFVAL { off }
::= { atmOamStatEntry 15 }
atmOamStatRdiTxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM remote defect indication (RDI) cells
that have been transmitted since last change of RdiState."
::= { atmOamStatEntry 16 }
atmOamStatRdiRxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM remote defect indication (RDI) cells
that have been received since last change of RdiState."
::= { atmOamStatEntry 17 }
atmOamStatTotalRdiTxCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The totoal number of OAM remote defect indication (RDI) cells
that have been transmitted."
::= { atmOamStatEntry 18 }
atmOamStatTotalRdiRxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of OAM remote defect indication (RDI) cells
that have been received."
::= { atmOamStatEntry 19 }
atmOamStatCCActivatorState OBJECT-TYPE
SYNTAX INTEGER {
inactive(1),
wait-act-con(2),
active(3),
wait-deact-con(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The status of the initiated CC negotiation, inactive(1)
is the initial status, wait-act-con(2) is set after
sending an CC activation request, active(3) is reached
after receiving the CC activation confirmation whereas
wait-deact-con(4) is used to indicate awaiting the
CC deactivation confirmation."
DEFVAL { inactive }
::= { atmOamStatEntry 20 }
atmOamStatCCActivatorDirection OBJECT-TYPE
SYNTAX INTEGER {
sink(1),
source(2),
both(3),
not-applicable(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The direction of action indicated by a received CC activation
confirmation, source(1) correlates with 'A-B', sink(2) with
'B-A' and both(3) with 'A-B' and 'B-A'."
DEFVAL { not-applicable }
::= { atmOamStatEntry 21 }
atmOamStatCCActivatorCorr OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The correlation of the last CC activation message sent
to the responder."
::= { atmOamStatEntry 22 }
atmOamStatCCResponderState OBJECT-TYPE
SYNTAX INTEGER {
inactive(1),
active(3),
wait-deact-con(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The status of the passive CC negotiation, inactive(1)
is the initial status, active(3) is reached after receiving
an CC activation request whereas wait-deact-con(4) is used
to indicate awaiting the CC deactivation confirmation."
DEFVAL { inactive }
::= { atmOamStatEntry 23 }
atmOamStatCCResponderDirection OBJECT-TYPE
SYNTAX INTEGER {
source(1),
sink(2),
both(3),
not-applicable(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The direction of action indicated by a received CC activation
request, source(1) correlates with 'B-A', sink(2) with
'A-B' and both(3) with 'A-B' and 'B-A'."
DEFVAL { not-applicable }
::= { atmOamStatEntry 24 }
atmOamStatCCResponderCorr OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The correlation of the received CC activation message."
::= { atmOamStatEntry 25 }
atmOamStatCCTxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM continuity check cells
that have been sent to the target in this sequence."
::= { atmOamStatEntry 26 }
atmOamStatCCRxCells OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of OAM continuity check cells
that have been received from the target in this sequence."
::= { atmOamStatEntry 27 }
---
--- Ethernet over ATM (LAN emulation) PVC table
---
ethoaPvcTable OBJECT-TYPE
SYNTAX SEQUENCE OF EthoaPvcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The ethoaPvcTable displays all virtual ethernets defined for
a VCI/VPI on a specified hardware."
::= { atm 15 }
ethoaPvcEntry OBJECT-TYPE
SYNTAX EthoaPvcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { ethoaPvcVpi, ethoaPvcVci, ethoaPvcAtmIfIndex }
::= { ethoaPvcTable 1 }
EthoaPvcEntry ::=
SEQUENCE {
ethoaPvcIfIndex INTEGER,
ethoaPvcDescr DisplayString,
ethoaPvcAtmIfIndex INTEGER,
ethoaPvcVpi INTEGER,
ethoaPvcVci INTEGER,
ethoaPvcEncapsulation INTEGER,
ethoaPvcPhysAddress PhysAddress
}
ethoaPvcIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object contains an interface index and assigns the
row to an entry in ifTable. When creating new entries
in the table, the value of this object shall be set to 0.
The next free ifIndex value is than allocated and assigned
to the object. At the same time a new interface is created
in the IfTable."
DEFVAL { 0 }
::= { ethoaPvcEntry 1 }
ethoaPvcDescr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Short description of the configured PVC"
::= { ethoaPvcEntry 2 }
ethoaPvcAtmIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Index to the ATM hardware."
::= { ethoaPvcEntry 3 }
ethoaPvcVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Path Connection."
DEFVAL { 8 }
::= { ethoaPvcEntry 4 }
ethoaPvcVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection."
DEFVAL { 32 }
::= { ethoaPvcEntry 5 }
ethoaPvcEncapsulation OBJECT-TYPE
SYNTAX INTEGER {
bridged-no-fcs(1), -- without frame checksum (FCS
bridged-fcs(2), -- with frame checksum (FCS)
vc-multiplexed(3), -- VC multiplexing
delete(10)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This values decides whether frames are send without FCS(1),
with FCS(2) or wether VC multiplexing is used."
DEFVAL { bridged-no-fcs }
::= { ethoaPvcEntry 6 }
ethoaPvcPhysAddress OBJECT-TYPE
SYNTAX PhysAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The MAC-Address used for the virtual interface."
::= { ethoaPvcEntry 7 }
---
--- raw protocol Pvc table
---
rpoaPvcTable OBJECT-TYPE
SYNTAX SEQUENCE OF RpoaPvcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table configures Vpi/Vci for raw protocols
(IP, IPX, etc.)"
::= { atm 16 }
rpoaPvcEntry OBJECT-TYPE
SYNTAX RpoaPvcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { rpoaPvcVpi, rpoaPvcVci, rpoaPvcAtmIfIndex }
::= { rpoaPvcTable 1 }
RpoaPvcEntry ::=
SEQUENCE {
rpoaPvcIfIndex INTEGER,
rpoaPvcDescr DisplayString,
rpoaPvcAtmIfIndex INTEGER,
rpoaPvcVpi INTEGER,
rpoaPvcVci INTEGER,
rpoaPvcEncapsulation INTEGER
}
rpoaPvcIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object contains an interface index and assigns the
row to an entry in ifTable. When creating new entries
in the table, the value of this object shall be set to 0.
The next free ifIndex value is than allocated and assigned
to the object. At the same time a new interface is created
in the IfTable."
DEFVAL { 0 }
::= { rpoaPvcEntry 1 }
rpoaPvcDescr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Short description of the configured PVC"
::= { rpoaPvcEntry 2 }
rpoaPvcAtmIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Index to the ATM hardware."
::= { rpoaPvcEntry 3 }
rpoaPvcVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Path Connection."
DEFVAL { 8 }
::= { rpoaPvcEntry 4 }
rpoaPvcVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection."
DEFVAL { 32 }
::= { rpoaPvcEntry 5 }
rpoaPvcEncapsulation OBJECT-TYPE
SYNTAX INTEGER {
non-iso(1),
iso(2),
vc-multiplexed(3),
delete(10)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This values decides whether frames are send codes
with LLC 0xAA 0xAA (non-ISO), LLC 0xFE 0xFE (ISO)
or wether VC multiplexing is used."
DEFVAL { non-iso }
::= { rpoaPvcEntry 6 }
---
--- pppoa Pvc Table
---
pppoaPvcTable OBJECT-TYPE
SYNTAX SEQUENCE OF PppoaPvcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table configures Vpi/Vci for PPP oaver AAL5 (PPPoA)
permanent and on-demand sessions."
::= { atm 17 }
pppoaPvcEntry OBJECT-TYPE
SYNTAX PppoaPvcEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { pppoaPvcVpi, pppoaPvcVci, pppoaPvcAtmIfIndex }
::= { pppoaPvcTable 1 }
PppoaPvcEntry ::=
SEQUENCE {
pppoaPvcIfIndex INTEGER,
pppoaPvcDescr DisplayString,
pppoaPvcAtmIfIndex INTEGER,
pppoaPvcVpi INTEGER,
pppoaPvcVci INTEGER,
pppoaPvcEncapsulation INTEGER,
pppoaPvcClientType INTEGER
}
pppoaPvcIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object contains an interface index and refers to an
entry in ifTable. When creating new entries in the table,
the next free ifIndex value is than allocated and assigned
to the object. At the same time a new interface is created
in the IfTable with that very index."
DEFVAL { 0 }
::= { pppoaPvcEntry 1 }
pppoaPvcDescr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Short description of the configured PVC"
::= { pppoaPvcEntry 2 }
pppoaPvcAtmIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Index to the ATM hardware."
::= { pppoaPvcEntry 3 }
pppoaPvcVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Path Connection."
DEFVAL { 8 }
::= { pppoaPvcEntry 4 }
pppoaPvcVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection."
DEFVAL { 32 }
::= { pppoaPvcEntry 5 }
pppoaPvcEncapsulation OBJECT-TYPE
SYNTAX INTEGER {
vc-multiplexed(1),
llc(2),
delete(10)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value decides whether VC multiplexing or
LLC encapsulation is used."
DEFVAL { vc-multiplexed }
::= { pppoaPvcEntry 6 }
pppoaPvcClientType OBJECT-TYPE
SYNTAX INTEGER {
permanent(1),
on-demand(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This variable defines whether the PPP over AAL5 session
will be established permanent(1) or initiated on-demand(2)."
DEFVAL { on-demand }
::= { pppoaPvcEntry 7 }
--- VC-related ATM QoS (ATM service categories)
atmQosVccTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmQosVccEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table provides QoS information for each active ATM VC on
the related ATM interface"
::= { atm 19 }
atmQosVccEntry OBJECT-TYPE
SYNTAX AtmQosVccEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the table, containing ATM QoS parameters about a
particular virtual connection."
INDEX { atmQosVccAtmIfIndex, atmQosVccVpi, atmQosVccVci }
::= { atmQosVccTable 1 }
AtmQosVccEntry ::=
SEQUENCE {
atmQosVccAtmIfIndex INTEGER,
atmQosVccVpi INTEGER,
atmQosVccVci INTEGER,
atmQosVccService INTEGER,
atmQosVccOutPcr INTEGER,
atmQosVccOutScr INTEGER,
atmQosVccOutMbs INTEGER,
atmQosVccOutMcr INTEGER
}
atmQosVccAtmIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The interface index of the associated ATM hardware."
::= { atmQosVccEntry 1 }
atmQosVccVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VPI value of this Virtual Channel Connection."
::= { atmQosVccEntry 2 }
atmQosVccVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The VCI value of this Virtual Channel Connection."
::= { atmQosVccEntry 3 }
atmQosVccService OBJECT-TYPE
SYNTAX INTEGER { -- ATM Forum UNI 4.0
cbr(1),
vbr(2),
-- vbr2(3),
vbr3(4),
-- vbr-rt(5),
-- vbr2-rt(6),
-- vbr3-rt(7),
ubr(8),
-- ubr2(9),
-- abr(10),
delete(20)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The ATM service category of this virtual circuit connection:
cbr
vbr
vbr2
vbr3 VBR1 + Best Effort
vbr-rt real-time
vbr2-rt real-time
vbr3-rt real-time
ubr Best Effort
ubr2 Best Effort
abr
delete
"
DEFVAL { ubr }
::= { atmQosVccEntry 4 }
atmQosVccOutPcr OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Output Peak Cell Rate (PCR) in bps."
::= { atmQosVccEntry 5 }
atmQosVccOutScr OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Output Sustained Cell Rate (SCR) in bps."
::= { atmQosVccEntry 6 }
atmQosVccOutMbs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Output Maximum Burst Size (MBS) in Bytes, only for
atmQosVccService vbr-rt(2) and vbr-nrt(3) (ATM service
service category VBR)."
::= { atmQosVccEntry 7 }
atmQosVccOutMcr OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Output Minimum Cell Rate (MCR) in bps for connection with
vbr-nrt(3)."
::= { atmQosVccEntry 8 }
---
--- ATM ATUR Performance Data Table
---
atmAturPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmAturPerfDataEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { atm 20 }
atmAturPerfDataEntry OBJECT-TYPE
SYNTAX AtmAturPerfDataEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in atmAturPerfDataTable."
INDEX { atmAturPerfIfIndex }
::= { atmAturPerfDataTable 1 }
AtmAturPerfDataEntry ::= SEQUENCE {
atmAturPerfIfIndex INTEGER,
atmAturPerfIdleCells INTEGER,
atmAturPerfDataCells INTEGER,
atmAturPerfLcds INTEGER,
atmAturPerfHecs INTEGER,
atmAturPerfCurr15MinTimeElapsed INTEGER,
atmAturPerfCurr15MinIdleCells INTEGER,
atmAturPerfCurr15MinDataCells INTEGER,
atmAturPerfCurr15MinLcds INTEGER,
atmAturPerfCurr15MinHecs INTEGER,
atmAturPerfCurr1DayTimeElapsed INTEGER,
atmAturPerfCurr1DayIdleCells INTEGER,
atmAturPerfCurr1DayDataCells INTEGER,
atmAturPerfCurr1DayLcds INTEGER,
atmAturPerfCurr1DayHecs INTEGER,
atmAturPerfPrev1DayIdleCells INTEGER,
atmAturPerfPrev1DayDataCells INTEGER,
atmAturPerfPrev1DayLcds INTEGER,
atmAturPerfPrev1DayHecs INTEGER
}
atmAturPerfIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Specifies the ATM interface index."
::= { atmAturPerfDataEntry 1 }
atmAturPerfIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells."
::= { atmAturPerfDataEntry 2 }
atmAturPerfDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells."
::= { atmAturPerfDataEntry 3 }
atmAturPerfLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of Loss of Cell Delineation failures since
agent reset."
::= { atmAturPerfDataEntry 4 }
atmAturPerfHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of Header Error Check failures since
agent reset."
::= { atmAturPerfDataEntry 5 }
atmAturPerfCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX INTEGER (0..899)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total elapsed seconds in this interval."
::= { atmAturPerfDataEntry 11 }
atmAturPerfCurr15MinIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells in the mandatory 15 minute interval."
::= { atmAturPerfDataEntry 12 }
atmAturPerfCurr15MinDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells in the mandatory 15 minute interval."
::= { atmAturPerfDataEntry 13 }
atmAturPerfCurr15MinLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the mandatory 15 minute interval
when there was Loss of Cell Delineation."
::= { atmAturPerfDataEntry 14 }
atmAturPerfCurr15MinHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the mandatory 15 minute interval
when there was Header Error Check failures."
::= { atmAturPerfDataEntry 15 }
atmAturPerfCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX INTEGER (0..86399)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of seconds that have elapsed since the
beginning of the mandatory 1-day interval."
::= { atmAturPerfDataEntry 18 }
atmAturPerfCurr1DayIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells during the mandatory day as measured
by atmAturPerfCurr1DayTimeElapsed."
::= { atmAturPerfDataEntry 19 }
atmAturPerfCurr1DayDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells during the mandatory day as measured
by atmAturPerfCurr1DayTimeElapsed."
::= { atmAturPerfDataEntry 20 }
atmAturPerfCurr1DayLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of seconds when there was Loss
of Cell Delineation during the mandatory day as measured
by atmAturPerfCurr1DayTimeElapsed."
::= { atmAturPerfDataEntry 21 }
atmAturPerfCurr1DayHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of seconds when there was Header
Error Check failures during the mandatory day as measured
by atmAturPerfCurr1DayTimeElapsed."
::= { atmAturPerfDataEntry 22 }
atmAturPerfPrev1DayIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells within the most recent previous
1-day period."
::= { atmAturPerfDataEntry 26 }
atmAturPerfPrev1DayDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells within the most recent previous
1-day period."
::= { atmAturPerfDataEntry 27 }
atmAturPerfPrev1DayLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Cell Delineation within the most recent previous
1-day period."
::= { atmAturPerfDataEntry 28 }
atmAturPerfPrev1DayHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the interval when there was
Header Error Check within the most recent previous
1-day period."
::= { atmAturPerfDataEntry 29 }
---
--- ATM ATUC Performance Data Table
---
atmAtucPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmAtucPerfDataEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
::= { atm 21 }
atmAtucPerfDataEntry OBJECT-TYPE
SYNTAX AtmAtucPerfDataEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in atmAtucPerfDataTable."
INDEX { atmAtucPerfIfIndex }
::= { atmAtucPerfDataTable 1 }
AtmAtucPerfDataEntry ::= SEQUENCE {
atmAtucPerfIfIndex INTEGER,
atmAtucPerfIdleCells INTEGER,
atmAtucPerfDataCells INTEGER,
atmAtucPerfLcds INTEGER,
atmAtucPerfHecs INTEGER,
atmAtucPerfCurr15MinTimeElapsed INTEGER,
atmAtucPerfCurr15MinIdleCells INTEGER,
atmAtucPerfCurr15MinDataCells INTEGER,
atmAtucPerfCurr15MinLcds INTEGER,
atmAtucPerfCurr15MinHecs INTEGER,
atmAtucPerfCurr1DayTimeElapsed INTEGER,
atmAtucPerfCurr1DayIdleCells INTEGER,
atmAtucPerfCurr1DayDataCells INTEGER,
atmAtucPerfCurr1DayLcds INTEGER,
atmAtucPerfCurr1DayHecs INTEGER,
atmAtucPerfPrev1DayIdleCells INTEGER,
atmAtucPerfPrev1DayDataCells INTEGER,
atmAtucPerfPrev1DayLcds INTEGER,
atmAtucPerfPrev1DayHecs INTEGER
}
atmAtucPerfIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Specifies the ATM interface index."
::= { atmAtucPerfDataEntry 1 }
atmAtucPerfIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells."
::= { atmAtucPerfDataEntry 2 }
atmAtucPerfDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells."
::= { atmAtucPerfDataEntry 3 }
atmAtucPerfLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of Loss of Cell Delineation failures since
agent reset."
::= { atmAtucPerfDataEntry 4 }
atmAtucPerfHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of Header Error Check failures since
agent reset."
::= { atmAtucPerfDataEntry 5 }
atmAtucPerfCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX INTEGER (0..899)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total elapsed seconds in this interval."
::= { atmAtucPerfDataEntry 11 }
atmAtucPerfCurr15MinIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells in the mandatory 15 minute interval."
::= { atmAtucPerfDataEntry 12 }
atmAtucPerfCurr15MinDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells in the mandatory 15 minute interval."
::= { atmAtucPerfDataEntry 13 }
atmAtucPerfCurr15MinLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the mandatory 15 minute interval
when there was Loss of Cell Delineation."
::= { atmAtucPerfDataEntry 14 }
atmAtucPerfCurr15MinHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the mandatory 15 minute interval
when there was Header Error Check failures."
::= { atmAtucPerfDataEntry 15 }
atmAtucPerfCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX INTEGER (0..86399)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of seconds that have elapsed since the
beginning of the mandatory 1-day interval."
::= { atmAtucPerfDataEntry 18 }
atmAtucPerfCurr1DayIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells during the mandatory day as measured
by atmAtucPerfCurr1DayTimeElapsed."
::= { atmAtucPerfDataEntry 19 }
atmAtucPerfCurr1DayDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells during the mandatory day as measured
by atmAtucPerfCurr1DayTimeElapsed."
::= { atmAtucPerfDataEntry 20 }
atmAtucPerfCurr1DayLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of seconds when there was Loss
of Cell Delineation during the mandatory day as measured
by atmAtucPerfCurr1DayTimeElapsed."
::= { atmAtucPerfDataEntry 21 }
atmAtucPerfCurr1DayHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of the number of seconds when there was Header
Error Check failures during the mandatory day as measured
by atmAtucPerfCurr1DayTimeElapsed."
::= { atmAtucPerfDataEntry 22 }
atmAtucPerfPrev1DayIdleCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM idle cells within the most recent previous
1-day period."
::= { atmAtucPerfDataEntry 26 }
atmAtucPerfPrev1DayDataCells OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ATM data cells within the most recent previous
1-day period."
::= { atmAtucPerfDataEntry 27 }
atmAtucPerfPrev1DayLcds OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the interval when there was
Loss of Cell Delineation within the most recent previous
1-day period."
::= { atmAtucPerfDataEntry 28 }
atmAtucPerfPrev1DayHecs OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of seconds in the interval when there was
Header Error Check within the most recent previous
1-day period."
::= { atmAtucPerfDataEntry 29 }
END
View Git Blame Copy Permalink