WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/zte/ZTE-DSL-SYSCTRL-MIB

3845 lines
136 KiB
Plaintext
Raw Permalink Blame History

-- File Name : ZTE-DSL-SYSCTRL-MIB.mib
-- Date : Mon Oct 17 14:13:24 GMT+08:00 2005
-- Author : ZTE Nms dept.
--
-- Zte Dsl SYS-CTRL Mib
--
--
ZTE-DSL-SYSCTRL-MIB DEFINITIONS ::= BEGIN
IMPORTS
zxDsl
FROM ZTE-DSL-MIB
RowStatus, DisplayString, TruthValue, MacAddress
FROM SNMPv2-TC
DisplayString, ifIndex,ifAdminStatus, ifOperStatus, ifType
FROM RFC1213-MIB
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, IpAddress, TimeTicks, Counter32, Gauge32, Integer32, Unsigned32
FROM SNMPv2-SMI
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
InetAddress, InetAddressType, InetAddressPrefixLength, InetAutonomousSystemNumber
FROM INET-ADDRESS-MIB;
zxDslSysctrlMib MODULE-IDENTITY
LAST-UPDATED "200404151500Z"
ORGANIZATION "ZTE Corporation"
CONTACT-INFO "ma ke
Mail: zte@zte.com.cn
Tel : 021-68896477"
DESCRIPTION "This MIB defines zte dsl managed objects."
::= { zxDsl 3 }
-- TEXTUAL-CONVENTIONS --
PortList ::= TEXTUAL-CONVENTION
DISPLAY-HINT ""
STATUS current
DESCRIPTION
"Each octet within this value specifies a set of eight
ports, with the first octet specifying ports 1 through
8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port
is not included if its bit has a value of '0'."
SYNTAX OCTET STRING
zxDslSysctrlObjects OBJECT IDENTIFIER
::= { zxDslSysctrlMib 1 }
zxDslSysctrlTrapObjects OBJECT IDENTIFIER
::= { zxDslSysctrlMib 2 }
zxDslSysCompatibility OBJECT IDENTIFIER
::= { zxDslSysctrlMib 3 }
------------------------------------------------------------------------------------
zxDslPhysical OBJECT IDENTIFIER
::= { zxDslSysctrlObjects 1 }
zxDslRackTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslRackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { zxDslPhysical 1 }
zxDslRackEntry OBJECT-TYPE
SYNTAX ZxDslRackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in zxDslRackTable."
INDEX { zxDslRackNo }
::= { zxDslRackTable 1 }
ZxDslRackEntry ::= SEQUENCE {
zxDslRackNo Integer32,
zxDslRackType Integer32,
zxDslRackMaxShelfNum Integer32,
zxDslRackRowStatus RowStatus
}
zxDslRackNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ":i"
::= { zxDslRackEntry 1 }
zxDslRackType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION ":z"
::= { zxDslRackEntry 2 }
zxDslRackMaxShelfNum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION ",:? 'O:Fp"
::= { zxDslRackEntry 3 }
zxDslRackRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "insert,delete"
::= { zxDslRackEntry 4 }
zxDslShelfTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslShelfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { zxDslPhysical 2 }
zxDslShelfEntry OBJECT-TYPE
SYNTAX ZxDslShelfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in zxDslShelfTable."
INDEX { zxDslShelfRackNo, zxDslShelfNo }
::= { zxDslShelfTable 1 }
ZxDslShelfEntry ::= SEQUENCE {
zxDslShelfRackNo Integer32,
zxDslShelfNo Integer32,
zxDslShelfType Integer32,
zxDslShelfMaxSlotNum Integer32,
zxDslShelfInvSn DisplayString,
zxDslShelfCleiCode DisplayString,
zxDslShelfRowStatus RowStatus
}
zxDslShelfRackNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Rack no."
DEFVAL {1}
::= { zxDslShelfEntry 1 }
zxDslShelfNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Shelf no."
DEFVAL {1}
::= { zxDslShelfEntry 2 }
zxDslShelfType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslShelfEntry 3 }
zxDslShelfMaxSlotNum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Max Slot Number in a shelf."
::= { zxDslShelfEntry 4 }
zxDslShelfInvSn OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 64 ) )
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This MIB is defined for serial number of this shelf.
it is used by inventroy management."
::= { zxDslShelfEntry 5 }
zxDslShelfCleiCode OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 64 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This MIB is defined for CLEI code of this card.
it is used by inventroy management.Pls reference
http://www.commonlanguage.com to get knowledge about CLEI code.
"
REFERENCE "http://www.commonlanguage.com"
::= { zxDslShelfEntry 6 }
zxDslShelfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "insert,delete"
::= { zxDslShelfEntry 15 }
zxDslBoardConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslBoardConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { zxDslPhysical 3 }
zxDslBoardConfigEntry OBJECT-TYPE
SYNTAX ZxDslBoardConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in zxDslBoardConfigTable."
INDEX { zxDslBoardConfigRackNo, zxDslBoardConfigShelfNo, zxDslBoardConfigSlotNo }
::= { zxDslBoardConfigTable 1 }
ZxDslBoardConfigEntry ::= SEQUENCE {
zxDslBoardConfigRackNo Integer32,
zxDslBoardConfigShelfNo Integer32,
zxDslBoardConfigSlotNo Integer32,
zxDslBoardConfigSubType Integer32,
zxDslBoardConfigBaseType Integer32,
zxDslBoardConfigHardVerType Integer32,
zxDslBoardConfigRowStatus RowStatus
}
zxDslBoardConfigRackNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ""
::= { zxDslBoardConfigEntry 1 }
zxDslBoardConfigShelfNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ""
::= { zxDslBoardConfigEntry 2 }
zxDslBoardConfigSlotNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ""
::= { zxDslBoardConfigEntry 3 }
zxDslBoardConfigSubType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslBoardConfigEntry 4 }
zxDslBoardConfigBaseType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslBoardConfigEntry 5 }
zxDslBoardConfigHardVerType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This is used to configure linecard supporting 8220V1.X version or 8220V2.X
version and ADSL1 or ADSL2"
::= { zxDslBoardConfigEntry 6 }
zxDslBoardConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "insert,delete"
::= { zxDslBoardConfigEntry 7 }
zxDslSplitBoardTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslSplitBoardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { zxDslPhysical 4 }
zxDslSplitBoardEntry OBJECT-TYPE
SYNTAX ZxDslSplitBoardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in zxDslSplitBoardTable."
INDEX { zxDslSplitBoardRackNo, zxDslSplitBoardShelfNo, zxDslSplitBoardSlotNo }
::= { zxDslSplitBoardTable 1 }
ZxDslSplitBoardEntry ::= SEQUENCE {
zxDslSplitBoardRackNo Integer32,
zxDslSplitBoardShelfNo Integer32,
zxDslSplitBoardSlotNo Integer32,
zxDslSplitBoardPos Integer32,
zxDslSplitBoardStatus Integer32
}
zxDslSplitBoardRackNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "rack number"
::= { zxDslSplitBoardEntry 1 }
zxDslSplitBoardShelfNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "shelf number"
::= { zxDslSplitBoardEntry 2 }
zxDslSplitBoardSlotNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "slot number"
::= { zxDslSplitBoardEntry 3 }
zxDslSplitBoardPos OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "splitter board position 1 == SelfRack, 2 == SplitterRack 0 == NULL"
::= { zxDslSplitBoardEntry 4 }
zxDslSplitBoardStatus OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "splitter board status"
::= { zxDslSplitBoardEntry 5 }
zxDslSubBoardTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslSubBoardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { zxDslPhysical 5 }
zxDslSubBoardEntry OBJECT-TYPE
SYNTAX ZxDslSubBoardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in zxDslSubBoardTable."
INDEX { zxDslSubBoardRackNo, zxDslSubBoardShelfNo, zxDslSubBoardSlotNo, zxDslSubBoardSubCardNo }
::= { zxDslSubBoardTable 1 }
ZxDslSubBoardEntry ::= SEQUENCE {
zxDslSubBoardRackNo Integer32,
zxDslSubBoardShelfNo Integer32,
zxDslSubBoardSlotNo Integer32,
zxDslSubBoardSubCardNo Integer32,
zxDslSubBoardType Integer32,
zxDslSubBoardDescr OCTET STRING,
zxDslSubBoardStatus INTEGER,
zxDslSubBoardReset Integer32,
zxDslSubBoardRowStatus Integer32,
zxDslSubBoardHardVersion OCTET STRING,
zxDslSubBoardSoftVersion OCTET STRING,
zxDslSubBoardPortNum Integer32
}
zxDslSubBoardRackNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "rack number"
::= { zxDslSubBoardEntry 1 }
zxDslSubBoardShelfNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "shelf number"
::= { zxDslSubBoardEntry 2 }
zxDslSubBoardSlotNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "slot number"
::= { zxDslSubBoardEntry 3 }
zxDslSubBoardSubCardNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "subcard number"
::= { zxDslSubBoardEntry 4 }
zxDslSubBoardType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "subBoard type"
::= { zxDslSubBoardEntry 5 }
zxDslSubBoardDescr OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 1 .. 255 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "sub-board information."
::= { zxDslSubBoardEntry 6 }
zxDslSubBoardStatus OBJECT-TYPE
SYNTAX INTEGER
{
inService (1),
notInService(2),
hwOnline(3),
hwOffline(4),
configuring(5),
configFailed(6),
typeMismatch(7),
deactived(8),
faulty(9),
invalid(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This MIB is defined for the sub card status on the card.
inService(1) -- card pluged in,running normally and service is being
provided normally.
notInService(2)-- card pluged in,running normally but service is stopped.
hwOnline(3) -- card pluged in AND card communication is ok,but software
isn't running now.
hwOffline(4) -- card not pluged in,but added to agent's database only
configuring(5) -- card pluged in,but it is configuring
configFailed(6)-- card pluged in,but configuration failed
typeMismatch(7)-- card pluged in,but it's type is mismatch
deactived(8) -- card pluged in,but it is deactivated by a manager
faulty(9) -- fault occurs when card is running normally
invalid(10) -- invalid card instance,such as adding card failed.
"
::= { zxDslSubBoardEntry 7 }
zxDslSubBoardReset OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION ""
::= { zxDslSubBoardEntry 8 }
zxDslSubBoardRowStatus OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION ""
::= { zxDslSubBoardEntry 9 }
zxDslSubBoardHardVersion OBJECT-TYPE
SYNTAX OCTET STRING( SIZE ( 1 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "sub board hard version, default is UNKNOWN"
::= { zxDslSubBoardEntry 10 }
zxDslSubBoardSoftVersion OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 1 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "sub board software version, default is UNKNOWN"
::= { zxDslSubBoardEntry 11 }
zxDslSubBoardPortNum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "sub board port number"
::= { zxDslSubBoardEntry 12 }
zxDslBoardTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslBoardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table includes common attributes describing
both ends of the line. It is required for all ADSL
physical interfaces. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94)."
::= { zxDslPhysical 6 }
zxDslBoardEntry OBJECT-TYPE
SYNTAX ZxDslBoardEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in zxDslBoardTable."
INDEX { zxDslBoardRackNo, zxDslBoardShelfNo, zxDslBoardSlotNo }
::= { zxDslBoardTable 1 }
ZxDslBoardEntry ::= SEQUENCE {
zxDslBoardRackNo Integer32,
zxDslBoardShelfNo Integer32,
zxDslBoardSlotNo Integer32,
zxDslBoardType Integer32,
zxDslBoardDescr OCTET STRING,
zxDslBoardPortNum Integer32,
zxDslBoardPortType Integer32,
zxDslBoardAdminStatus INTEGER,
zxDslBoardOperStatus INTEGER,
zxDslBoardHardVersion OCTET STRING,
zxDslBoardSoftVersion OCTET STRING,
zxDslBoardSoftLastChange TimeTicks,
zxDslBoardReset Integer32,
zxDslBoardCpuLoad Integer32,
zxDslBoardCpuLoadThreshhold Integer32,
zxDslBoardMemUsage Integer32,
zxDslBoardMemUsageThreshhold Integer32,
zxDslBoardActPortNum Integer32,
zxDslBoardHardVerStatus Integer32,
zxDslBoardSoftVerCfg Integer32,
zxDslBoardStandByStatus INTEGER,
zxDslBoardMemTotalSize Integer32
}
zxDslBoardRackNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "rack number"
::= { zxDslBoardEntry 1 }
zxDslBoardShelfNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "shelf number"
::= { zxDslBoardEntry 2 }
zxDslBoardSlotNo OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "slot number"
::= { zxDslBoardEntry 3 }
zxDslBoardType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "board type"
::= { zxDslBoardEntry 4 }
zxDslBoardDescr OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 1 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "board descript"
::= { zxDslBoardEntry 5 }
zxDslBoardPortNum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "board portnum"
::= { zxDslBoardEntry 6 }
zxDslBoardPortType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "board port type"
::= { zxDslBoardEntry 7 }
zxDslBoardAdminStatus OBJECT-TYPE
SYNTAX INTEGER
{
unlock(3),
lock(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "board administrative status."
DEFVAL { unlock }
::= { zxDslBoardEntry 8 }
zxDslBoardOperStatus OBJECT-TYPE
SYNTAX INTEGER
{
unknown(1), -- card pluged in but can't get right state.
offline(2), -- card not pluged in,but added to agent's database only
online(3), -- card pluged in.hardware online or resetting
inService(4), -- card pluged in and running normally
standby(5), -- card pluged in,it is runing as a slave card.
configuring(6) -- card pluged in,but it is configuring data.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "board operational status"
::= { zxDslBoardEntry 9 }
zxDslBoardHardVersion OBJECT-TYPE
SYNTAX OCTET STRING( SIZE ( 1 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "board hard version"
::= { zxDslBoardEntry 10 }
zxDslBoardSoftVersion OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 1 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "board software version"
::= { zxDslBoardEntry 11 }
zxDslBoardSoftLastChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION "soft last change"
::= { zxDslBoardEntry 12 }
zxDslBoardReset OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Server as reset card"
::= { zxDslBoardEntry 13 }
zxDslBoardCpuLoad OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Server as cup load of card"
::= { zxDslBoardEntry 14 }
zxDslBoardCpuLoadThreshhold OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Server as cup load of card"
::= { zxDslBoardEntry 15 }
zxDslBoardMemUsage OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Server as memory usage rate of card"
::= { zxDslBoardEntry 16 }
zxDslBoardMemUsageThreshhold OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Server as memory usage rate of card"
::= { zxDslBoardEntry 17 }
zxDslBoardActPortNum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Server as active port numbers of card"
::= { zxDslBoardEntry 18 }
zxDslBoardHardVerStatus OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Server as v1 or v2 line card of 8000, g1 or g2 line type of 8000"
::= { zxDslBoardEntry 19 }
zxDslBoardSoftVerCfg OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Server as configuring the running software type on atugb"
::= { zxDslBoardEntry 20 }
zxDslBoardStandByStatus OBJECT-TYPE
SYNTAX INTEGER{master(1), slave(2), single(3)}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Board standBy status.
NOTE: Not available now. "
::= { zxDslBoardEntry 21 }
zxDslBoardMemTotalSize OBJECT-TYPE
SYNTAX Integer32
UNITS "KB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Total memory size of board"
::= { zxDslBoardEntry 22 }
-- Card Inventory Mgmt table
zxDslCardInvMgmtTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslCardInvMgmtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of card entries."
::= { zxDslPhysical 7 }
zxDslCardInvMgmtEntry OBJECT-TYPE
SYNTAX ZxDslCardInvMgmtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An card entry containing objects
describing the card in some slot."
INDEX { zxDslCardInvRack, zxDslCardInvShelf,
zxDslCardInvSlot, zxDslCardInvSubSlot }
::= { zxDslCardInvMgmtTable 1 }
ZxDslCardInvMgmtEntry ::= SEQUENCE {
zxDslCardInvRack Integer32,
zxDslCardInvShelf Integer32,
zxDslCardInvSlot INTEGER,
zxDslCardInvSubSlot INTEGER,
zxDslCardInvSn DisplayString,
zxDslCardInvCleiCode DisplayString
}
zxDslCardInvRack OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The rack number of the card"
::= { zxDslCardInvMgmtEntry 1 }
zxDslCardInvShelf OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The shelf number of the card"
::= { zxDslCardInvMgmtEntry 2 }
zxDslCardInvSlot OBJECT-TYPE
SYNTAX INTEGER(1..18)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The slot number of the card"
::= { zxDslCardInvMgmtEntry 3 }
zxDslCardInvSubSlot OBJECT-TYPE
SYNTAX INTEGER(0..4)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The sub slot number of the card.If there is no sublot,then this value
is 0. "
::= { zxDslCardInvMgmtEntry 4 }
zxDslCardInvSn OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The series number of the card."
::= { zxDslCardInvMgmtEntry 5 }
zxDslCardInvCleiCode OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The CLEI code of the card.It is a present of a cardtype."
::= { zxDslCardInvMgmtEntry 6 }
--------------------------------------------------------------------------------
-- Dsl enviroment monitoring mgmt,such as chassis temperature and fans.
zxDslEnvMon OBJECT IDENTIFIER ::= {zxDslSysctrlObjects 2}
zxDslEnvChassisTemperature OBJECT-TYPE
SYNTAX Integer32
UNITS "centigrade"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current temperature of the chassis."
::= { zxDslEnvMon 1 }
zxDslEnvTemperatureThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "centigrade"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The threshold of the chassis temperature,zxDslEnvTempExceeded trap
should be generated when zxDslEnvChassisTemperature is lareger than it.
Otherwise,zxDslEnvTempNormal trap should be generated when
zxDslEnvChassisTemperature is less than it."
DEFVAL { 75 }
::= { zxDslEnvMon 2 }
zxDslEnvTemperatureTrapEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative status of temperature alarm trap."
DEFVAL { enable }
::= { zxDslEnvMon 3 }
-- Fans mgmt ----------------
zxDslEnvFanMgmtCap OBJECT-TYPE
SYNTAX BITS
{
unused(0),
speed_control(1),
alarm_send(2),
shutdown_control(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The capabilities to be controlled.
speed_control(1) -- The speed of fun can be controlled
alarm_send(2) -- Alarm of fans can be generated and send to manager.
shutdown_control(3) -- Which fan is running can be controlled.
"
::= { zxDslEnvMon 4 }
zxDslEnvFanSpeedCtrlType OBJECT-TYPE
SYNTAX INTEGER
{
auto_SpeedControl(1),
fix_Speed(2),
noSpeedControl(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The control type of fan speed.
If fix_Speed(2) is selected,zxDslEnvFanSpeed in zxDslEnvFanTable
should be configured.
"
::= { zxDslEnvMon 5 }
zxDslEnvFanTrapEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative status of fun's alarm trap."
DEFVAL { enable }
::= { zxDslEnvMon 6 }
zxDslEnvFanTrayAlarmBeep OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable the alarm beep for fun tray."
DEFVAL { enable }
::= { zxDslEnvMon 7 }
zxDslEnvEpmRelaySwitchEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable the EPM relay switch.
if it's disabled, there will be four environment switch,
and if it's enabled, there will be only two environment switch.
Other two environment switch and the EMP serial port are alternative."
DEFVAL { enable }
::= { zxDslEnvMon 8 }
zxDslEnvLossOfPowerTrapEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable the dying gasp event when the device is
power off or power failure."
DEFVAL { enable }
::= { zxDslEnvMon 9 }
-- fans table ----------------
zxDslEnvFanTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslEnvFanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of fan's managed objects.Each row instance represents
a controllable fan unit,may be a controlled fan or a controlled fan tray.
When zxDslEnvFanOperstatus and zxDslEnvFanAdminstatus are mismatched,
zxDslEnvFanFailed trap should be sent to manager.If this error state
doesn't exist,zxDslEnvFanRecovered trap should be sent.
"
::= { zxDslEnvMon 10 }
zxDslEnvFanEntry OBJECT-TYPE
SYNTAX ZxDslEnvFanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"a entry of this table."
INDEX { zxDslEnvFanIndex }
::= { zxDslEnvFanTable 1 }
ZxDslEnvFanEntry ::= SEQUENCE {
zxDslEnvFanIndex Integer32,
zxDslEnvFanSpeed INTEGER,
zxDslEnvFanAdminstatus INTEGER,
zxDslEnvFanOperstatus INTEGER
}
zxDslEnvFanIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this fan or fan tray referred to in this table entry."
::= { zxDslEnvFanEntry 1 }
zxDslEnvFanSpeed OBJECT-TYPE
SYNTAX INTEGER
{
auto_speed(0),-- read only
low_speed(1),
middle_speed(2),
normal_speed(3),
high_speed(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The speed of fan.
If it is to be set, zxDslEnvFanSpeedCtrlType must be fix_Speed(2).
"
DEFVAL { normal_speed }
::= { zxDslEnvFanEntry 2 }
zxDslEnvFanAdminstatus OBJECT-TYPE
SYNTAX INTEGER
{
up(1),
down(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The adminstrative status of fan"
DEFVAL { up }
::= { zxDslEnvFanEntry 3 }
zxDslEnvFanOperstatus OBJECT-TYPE
SYNTAX INTEGER
{
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The operational status of a fan."
::= { zxDslEnvFanEntry 4 }
-- switch table ----------------
zxDslEnvDeviceTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslEnvDeviceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of environment monitor Device."
::= { zxDslEnvMon 11 }
zxDslEnvDeviceEntry OBJECT-TYPE
SYNTAX ZxDslEnvDeviceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"a entry of this table."
INDEX { zxDslEnvEnvDeviceIndex }
::= { zxDslEnvDeviceTable 1 }
ZxDslEnvDeviceEntry ::= SEQUENCE {
zxDslEnvEnvDeviceIndex Integer32,
zxDslEnvEnvDeviceName DisplayString,
zxDslEnvDeviceRowStatus RowStatus
}
zxDslEnvEnvDeviceIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this environment monitor Device.
"
::= { zxDslEnvDeviceEntry 1 }
zxDslEnvEnvDeviceName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"the name of environment monitor Device.
zxDslEnvEnvDeviceIndex 1-50 is default value,can't delete or modify.
"
::= { zxDslEnvDeviceEntry 2 }
zxDslEnvDeviceRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The status of this table."
::= { zxDslEnvDeviceEntry 3 }
zxDslEnvSwitchTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslEnvSwitchEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of switch's managed objects.Each row instance represents
a device connected with this switch.
"
::= { zxDslEnvMon 12 }
zxDslEnvSwitchEntry OBJECT-TYPE
SYNTAX ZxDslEnvSwitchEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"a entry of this table."
INDEX { zxDslEnvSwitchIndex }
::= { zxDslEnvSwitchTable 1 }
ZxDslEnvSwitchEntry ::= SEQUENCE {
zxDslEnvSwitchIndex Integer32,
zxDslEnvDeviceId Integer32,
zxDslEnvSwitchNormalStatus INTEGER,
zxDslEnvSwitchEnable INTEGER,
zxDslEnvSwitchCurrentStatus INTEGER
}
zxDslEnvSwitchIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this Switch."
::= { zxDslEnvSwitchEntry 1 }
zxDslEnvDeviceId OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The device id.If this switch can't connect with any device,
zxDslEnvDeviceId set to 0."
DEFVAL { 0 }
::= { zxDslEnvSwitchEntry 2 }
zxDslEnvSwitchNormalStatus OBJECT-TYPE
SYNTAX INTEGER
{
low(0),
high(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Threshold of this environment monitor Device."
::= { zxDslEnvSwitchEntry 3 }
zxDslEnvSwitchEnable OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables and disables Trap of this environment monitor Device."
::= { zxDslEnvSwitchEntry 4 }
zxDslEnvSwitchCurrentStatus OBJECT-TYPE
SYNTAX INTEGER
{
low(0),
high(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current status of this environment monitor Device."
::= { zxDslEnvSwitchEntry 5 }
zxDslEnvExteriorPower OBJECT IDENTIFIER ::= {zxDslEnvMon 13}
zxDslEnvExteriorPowerEnable OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables and disables Trap of Exterior Power."
::= { zxDslEnvExteriorPower 1 }
zxDslEnvBatteriesVoltage OBJECT IDENTIFIER ::= {zxDslEnvMon 14}
zxDslEnvBatteriesVoltageEnable OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables and disables Trap of Batteries Voltage."
::= { zxDslEnvBatteriesVoltage 1 }
zxDslEnvPowerFailure OBJECT IDENTIFIER ::= {zxDslEnvMon 15}
zxDslEnvPowerFailureEnable OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables and disables Trap of Power Failure."
::= { zxDslEnvPowerFailure 1 }
zxDslEnvCtrlObjects OBJECT IDENTIFIER ::= {zxDslEnvMon 16}
zxDslEnvMonitorInterfaceUsage OBJECT-TYPE
SYNTAX INTEGER
{
epm(1),
battery(2),
noUse(3),
noSupport(4),
electricLock(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The equipment type connected to the enviroment monitor interface.
The possible values are:
epm(1) - connect to EPM device
battery(2) - direct connect to battery
noUse(3) - support enviroment monitor interface, but not use.
noSupport(4) - doesn't support enviroment monitor interface.
electricLock(5) - connect to electric lock."
DEFVAL { storageBattery }
::= { zxDslEnvCtrlObjects 1 }
zxDslEnvMonitorInterfaceTrapEnable OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether linkUp/linkDown traps should be
generated for MonitorInterface."
DEFVAL { enable }
::= { zxDslEnvCtrlObjects 2 }
zxDslEnvFanAutoCtrlEnable OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disble the autocontrol of fan by temperature."
DEFVAL { disable }
::= { zxDslEnvCtrlObjects 3 }
zxDslEnvFanCtrlTemperatureThresh OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The temperature threshold of fan for start-up or shut down,
in Celsiur scale."
::= { zxDslEnvCtrlObjects 4 }
zxDslEnvTemperatureLowerThreshold OBJECT-TYPE
SYNTAX Integer32(-60..0)
UNITS "centigrade"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower threshold of the chassis temperature,the
zxDslTempUnderThreshTrap trap should be generated when
zxDslEnvChassisTemperature is lower than it.
Otherwise,zxDslTempUnderThreshTrapCleared trap should be generated
when zxDslEnvChassisTemperature 2 degrees higher than it."
DEFVAL { -30 }
::= { zxDslEnvCtrlObjects 5 }
zxDslEnvBatteryEnergySavingEnable OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"enable or disable energy saving for battery.
if enabled, device will switch to energy saving mode when the
exterior power lose and battery as power supply.
"
DEFVAL { disable }
::= { zxDslEnvCtrlObjects 6 }
zxDslEnvFanFaultInfo OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the failed fan list.
e.g., 1,3-5 means Fan 1,Fan 3,Fan 4 and Fan 5 are in failure.
"
::= { zxDslEnvCtrlObjects 7 }
zxDslEnvFanTotalNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total Number of Fans."
::= { zxDslEnvCtrlObjects 8 }
zxDslEnvMonitorElecLock OBJECT IDENTIFIER ::= {zxDslEnvMon 17}
zxDslEnvMonitorElecLockServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslEnvMonitorElecLockServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"electric lock server table. "
::= { zxDslEnvMonitorElecLock 1 }
zxDslEnvMonitorElecLockServerEntry OBJECT-TYPE
SYNTAX ZxDslEnvMonitorElecLockServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"electric lock server entry"
INDEX { zxDslEnvMonitorElecLockServerAddress }
::= { zxDslEnvMonitorElecLockServerTable 1 }
ZxDslEnvMonitorElecLockServerEntry ::= SEQUENCE {
zxDslEnvMonitorElecLockServerAddress InetAddress,
zxDslEnvMonitorElecLockServerRowStatus RowStatus
}
zxDslEnvMonitorElecLockServerAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The server address for electric lock monitor."
::= { zxDslEnvMonitorElecLockServerEntry 1 }
zxDslEnvMonitorElecLockServerRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "rowstatus"
::= { zxDslEnvMonitorElecLockServerEntry 2 }
--------------------------------------------------------------------------------
zxDslVersion OBJECT IDENTIFIER ::= {zxDslSysctrlObjects 3}
zxDslVerCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslVerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table entry containing AdslVersion information for each
port. These variables are not in RFC2495 configuration table."
::= { zxDslVersion 1 }
zxDslVerCfgEntry OBJECT-TYPE
SYNTAX ZxDslVerCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "AdslVersion information entry"
INDEX { zxDslVerTypeName }
::= { zxDslVerCfgTable 1 }
ZxDslVerCfgEntry ::= SEQUENCE {
zxDslVerTypeName SnmpAdminString,
zxDslEraseFileName SnmpAdminString,
zxDslActiveFileName SnmpAdminString,
zxDslEraseVerType Unsigned32
}
zxDslVerTypeName OBJECT-TYPE
SYNTAX SnmpAdminString( SIZE ( 0 .. 32 ) )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "
"
::= { zxDslVerCfgEntry 1 }
zxDslEraseFileName OBJECT-TYPE
SYNTAX SnmpAdminString( SIZE ( 0 .. 32 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
"
::= { zxDslVerCfgEntry 2 }
zxDslActiveFileName OBJECT-TYPE
SYNTAX SnmpAdminString( SIZE ( 0 .. 32 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
"
::= { zxDslVerCfgEntry 3 }
zxDslEraseVerType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
"
::= { zxDslVerCfgEntry 4 }
zxDslVersionTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslVersionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table entry containing AdslVersion information for each
port. These variables are not in RFC2495 configuration table."
::= { zxDslVersion 2 }
zxDslVersionEntry OBJECT-TYPE
SYNTAX ZxDslVersionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "AdslVersion information entry"
INDEX { zxDslVerTypeName, zxDslVerFileName }
::= { zxDslVersionTable 1 }
ZxDslVersionEntry ::= SEQUENCE {
zxDslVerFileName OCTET STRING,
zxDslVersionNo OCTET STRING,
zxDslVerType OCTET STRING,
zxDslVerCreateTime OCTET STRING,
zxDslVerDownLoadTime OCTET STRING,
zxDslVersionStatus OCTET STRING,
zxDslVerLen Unsigned32,
zxDslVersionState OCTET STRING
}
zxDslVerFileName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 64 ) )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "the file name of the version "
::= { zxDslVersionEntry 1 }
zxDslVersionNo OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version id"
::= { zxDslVersionEntry 2 }
zxDslVerType OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version type"
::= { zxDslVersionEntry 3 }
zxDslVerCreateTime OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version Create Time"
::= { zxDslVersionEntry 4 }
zxDslVerDownLoadTime OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version DownLoad Time"
::= { zxDslVersionEntry 5 }
zxDslVersionStatus OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version Status"
::= { zxDslVersionEntry 6 }
zxDslVerLen OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version length"
::= { zxDslVersionEntry 7 }
zxDslVersionState OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version active state"
::= { zxDslVersionEntry 8 }
zxDslPatchTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslPatchEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table entry containing patch information."
::= { zxDslVersion 3 }
zxDslPatchEntry OBJECT-TYPE
SYNTAX ZxDslPatchEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "patch information entry"
INDEX { zxDslPatchName }
::= { zxDslPatchTable 1 }
ZxDslPatchEntry ::= SEQUENCE {
zxDslPatchName OCTET STRING,
zxDslPatchSystemVersion OCTET STRING,
zxDslPatchVersionNo OCTET STRING,
zxDslPatchSize Unsigned32,
zxDslPatchStatus OCTET STRING,
zxDslPatchCreateTime OCTET STRING,
zxDslPatchActiveTime OCTET STRING,
zxDslPatchRunningTime OCTET STRING,
zxDslPatchDesc OCTET STRING,
zxDslPatchAdminStatus INTEGER
}
zxDslPatchName OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 64 ) )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "the file name of the patch "
::= { zxDslPatchEntry 1 }
zxDslPatchSystemVersion OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the system version of the patch"
::= { zxDslPatchEntry 2 }
zxDslPatchVersionNo OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version no of the patch"
::= { zxDslPatchEntry 3 }
zxDslPatchSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the version length of the patch"
::= { zxDslPatchEntry 4 }
zxDslPatchStatus OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 32 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the status of the patch, such as activated, deactivated and autorun"
::= { zxDslPatchEntry 5 }
zxDslPatchCreateTime OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the patch create time"
::= { zxDslPatchEntry 6 }
zxDslPatchActiveTime OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the patch active time"
::= { zxDslPatchEntry 7 }
zxDslPatchRunningTime OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the running time of the patch"
::= { zxDslPatchEntry 8 }
zxDslPatchDesc OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 64 ) )
MAX-ACCESS read-only
STATUS current
DESCRIPTION "the patch description"
::= { zxDslPatchEntry 9 }
zxDslPatchAdminStatus OBJECT-TYPE
SYNTAX INTEGER { active ( 1 ) , save ( 2 ), deactive ( 3 ), delete( 4 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "config the status of patch"
::= { zxDslPatchEntry 10 }
--------------------------------------------------------------------------------
zxDslCommon OBJECT IDENTIFIER ::= {zxDslSysctrlObjects 4}
zxDslCliPrompt OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "prompt name of the zxDsl. (ex. fasp#)"
::= { zxDslCommon 1 }
zxDslLineTestRootMode OBJECT-TYPE
SYNTAX INTEGER { rootMode ( 1 ) , notRootMode ( 2 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "A flag is to indicate whether the MasterToSLave transfering is going on."
::= { zxDslCommon 2 }
zxDslEPMConfType OBJECT-TYPE
SYNTAX INTEGER { csv ( 0 ) , epm ( 1 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "the EPM config type."
::= { zxDslCommon 3 }
zxDslSaveToNvm OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION ""
REFERENCE ""
DEFVAL { 0 }
::= { zxDslCommon 4 }
zxDslEraseNvm OBJECT-TYPE
SYNTAX Integer32 ( -2147483648 .. 2147483647 )
MAX-ACCESS read-write
STATUS current
DEFVAL { 0 }
::= { zxDslCommon 5 }
zxDslSwapCore OBJECT-TYPE
SYNTAX INTEGER { switch ( 1 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The flag that master to slave."
::= { zxDslCommon 6 }
zxDslBorrowBoardSet OBJECT-TYPE
SYNTAX INTEGER { default ( 1 ) , slot10 ( 10 ) , slot12 ( 12 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The borrow board type."
::= { zxDslCommon 7 }
zxDslBorrowBoardGet OBJECT-TYPE
SYNTAX INTEGER { default ( 1 ) , slot10 ( 10 ) , slot12 ( 12 ) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The actual borrow board type"
::= { zxDslCommon 8 }
zxDslSysDateTime OBJECT-TYPE
SYNTAX OCTET STRING ( SIZE ( 0 .. 20 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "yyyy-mm-dd HH:MM:SS.For example(2001-01-01 02:22:33)."
::= { zxDslCommon 9 }
zxDslTimeZoneOffset OBJECT-TYPE
SYNTAX Integer32(-12..12)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Time zone offset.
The zone offset can be 0 for GMT or it can be a value '+' or '-'
from GMT.
"
::= { zxDslCommon 10 }
zxDslIsHalfTimeZone OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Whether it is a half zone.If it is true(1),the local
time should be plused 0.5 hours."
::= { zxDslCommon 11 }
zxDslSystemReboot OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Server as reboot system."
::= { zxDslCommon 12 }
zxDslSystemPortList OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Server as port batch configuring."
::= { zxDslCommon 13 }
zxDslAutoSaveToNvmInterval OBJECT-TYPE
SYNTAX Integer32(0..168)
UNITS "hours"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION "The interval to save running configuration of agent to
flash media automatically.
The value 0 means disable the auto save flash operation."
DEFVAL { 0 }
::= { zxDslCommon 14 }
zxDslTimingSaveModifiedToNvmInterval OBJECT-TYPE
SYNTAX Integer32(0..1440)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The interval to save flash if running configuration of
agent modified, value 0 means disable the auto save flash
operation."
DEFVAL { 0 }
::= { zxDslCommon 15 }
zxDslTimingSaveToNvmInterval OBJECT-TYPE
SYNTAX Integer32(0..8760)
UNITS "hours"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The interval to force saving flash , value 0 means disable
the force save saving operation."
DEFVAL { 0 }
::= { zxDslCommon 16 }
zxDslUserSideMtu OBJECT-TYPE
SYNTAX Integer32(64..2047)
UNITS "byte"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The user side maximum transmission unit,
the packge from user side will be discard
while it exceed this limit."
DEFVAL { 1700 }
::= { zxDslCommon 17 }
zxDslSysMaxPortNumPerSlot OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The max port number per slot of the device.
This number is used to compute the ifIndex."
::= { zxDslCommon 18 }
zxDslSysOutbandPortUsage OBJECT-TYPE
SYNTAX INTEGER
{
outbandPort(1),
cascadePort(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The usage of outband port.
outbandPort(1) - Switch the port usage to outband port.
cascadePort(2) - Switch the port usage to cascade port.
"
DEFVAL { outbandPort }
::= { zxDslCommon 19 }
zxDslPerfStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslPerfStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table provides one row for each adsl interface.
Each row contains the perf statistic parameters for this adsl line"
::= { zxDslCommon 30 }
zxDslPerfStatEntry OBJECT-TYPE
SYNTAX ZxDslPerfStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry containing additional performance management information
applicable to a adsl line interface."
INDEX { ifIndex }
::= { zxDslPerfStatTable 1 }
ZxDslPerfStatEntry ::= SEQUENCE {
zxDslPerfStatType INTEGER,
zxDslPerfStatTableList BITS,
zxDslPerfStatAction INTEGER
}
zxDslPerfStatType OBJECT-TYPE
SYNTAX INTEGER
{
adsl (1),
shdsl(2),
vdsl (3),
etherlike(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of performance metrics to be updated."
::= { zxDslPerfStatEntry 1 }
zxDslPerfStatTableList OBJECT-TYPE
SYNTAX BITS
MAX-ACCESS read-write
STATUS current
DESCRIPTION "bitmap for perf statistic object table"
::= { zxDslPerfStatEntry 2 }
zxDslPerfStatAction OBJECT-TYPE
SYNTAX INTEGER { actOnPort ( 1 ) , noop ( 2 ) , actOnBoard ( 3 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "bitmap for perf statistic object table"
::= { zxDslPerfStatEntry 3 }
zxDslUserTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslUserEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table contain user information for web and console and telnet.."
::= { zxDslCommon 31 }
zxDslUserEntry OBJECT-TYPE
SYNTAX ZxDslUserEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A list of user information."
INDEX { zxDslUserIndex }
::= { zxDslUserTable 1 }
ZxDslUserEntry ::= SEQUENCE {
zxDslUserIndex Integer32,
zxDslUserName DisplayString,
zxDslUserPwd DisplayString,
zxDslUserAccess Integer32,
zxDslUserRowStatus INTEGER
}
zxDslUserIndex OBJECT-TYPE
SYNTAX Integer32 ( 1 .. 8 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A simple index into 'TmsCommonMiscUserTable'."
::= { zxDslUserEntry 1 }
zxDslUserName OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 15 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "A simple index into 'TmsCommonMiscUserTable'."
::= { zxDslUserEntry 2 }
zxDslUserPwd OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 32 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "A simple index into 'TmsCommonMiscUserTable'."
::= { zxDslUserEntry 3 }
zxDslUserAccess OBJECT-TYPE
SYNTAX Integer32 ( 1 .. 10 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "the user access in this row."
::= { zxDslUserEntry 4 }
zxDslUserRowStatus OBJECT-TYPE
SYNTAX INTEGER { valid ( 1 ) , invalid ( 2 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "the user state in this row."
::= { zxDslUserEntry 5 }
zxDslTrapHostTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslTrapHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table, which provides Trap target."
::= { zxDslCommon 33 }
zxDslTrapHostEntry OBJECT-TYPE
SYNTAX ZxDslTrapHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ""
INDEX { zxDslTrapHostIpAddr }
::= { zxDslTrapHostTable 1 }
ZxDslTrapHostEntry ::= SEQUENCE {
zxDslTrapHostIpAddr IpAddress,
zxDslTrapHostSnmpVer Integer32,
zxDslTrapHostCommunity DisplayString,
zxDslTrapHostIsZteNmsSever TruthValue,
zxDslTrapHostRowStatus RowStatus,
zxDslTrapHostEventType BITS,
zxDslTrapHostMinEventLevel INTEGER
}
zxDslTrapHostIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ""
::= { zxDslTrapHostEntry 1 }
zxDslTrapHostSnmpVer OBJECT-TYPE
SYNTAX Integer32 ( 0 .. 1 )
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslTrapHostEntry 2 }
zxDslTrapHostCommunity OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 64 ) )
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslTrapHostEntry 3 }
zxDslTrapHostIsZteNmsSever OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If or not it is a zte's nms.
true(1): it is a zte's nms;
false(2): it is not a zte's nms.
"
::= { zxDslTrapHostEntry 4 }
zxDslTrapHostRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslTrapHostEntry 5 }
zxDslTrapHostEventType OBJECT-TYPE
SYNTAX BITS {
equipmentEvent(0),
qualityOfServiceEvent(1),
communicationsEvent(2),
environmentEvent(3),
processingErrorEvent(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The event type that a receiver expects.
The event type are defined in ITU-T X.733.
- equipment event type:
An event of this type is principally
associated with an equipment fault;
- quality of service event type:
An event of this type is
principally associated with a degradation in the quality of a
service;
- communications event type:
An event of this type is principally
associated with the procedures and/or processes required to convey
information from one point to another;
- environmental event type:
An event of this type is principally
associated with a condition relating to an enclosure in which the
equipment resides.
- processing error event type:
An event of this type is
principally associated with a software or processing fault;
"
DEFVAL { { equipmentEvent,qualityOfServiceEvent,communicationsEvent,
environmentEvent,processingErrorEvent } }
::= { zxDslTrapHostEntry 6 }
zxDslTrapHostMinEventLevel OBJECT-TYPE
SYNTAX INTEGER {
cleared(0),
critical(1),
major(2),
minor(3),
warning(4),
notification(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The min event level that a receiver expects.If the actual event
level is more serious than this value,the event will be sent to
Event Receiver. For example,if this value is warning(4),all the
events that the level in cleared(0),critical(1),major(2),minor(3),
warning(4) will be sent,but notification(5) will not be sent.
The event levels are defined in ITU-T X.733.
- cleared: The Cleared severity level indicates the clearing of
one or more previously reported alarms. This alarm clears all
alarms for this managed object that have the same Alarm type,
Probable cause and Specific problems (if given).
Multiple associated notifications may be cleared by using
the Correlated notifications parameter (defined below).
This Recommendation | International Standard does not require that
the clearing of previously reported alarms be reported.
Therefore, a managing system cannot assume that the absence of
an alarm with the Cleared severity level means that the condition
that caused the generation of previous alarms is still present.
Managed object definers shall state if, and under which
conditions, the Cleared severity level is used.
- critical: The Critical severity level indicates that a service
affecting condition has occurred and an immediate corrective action
is required. Such a severity can be reported, for example, when
a managed object becomes totally out of service and its capability
must be restored.
- major: The Major severity level indicates that a service
affecting condition has developed and an urgent corrective action
is required. Such a severity can be reported, for example, when
there is a severe degradation in the capability of the managed
object and its full capability must be restored.
- minor: The Minor severity level indicates the existence of
a non-service affecting fault condition and that corrective action
should be taken in order to prevent a more serious (for example,
service affecting) fault. Such a severity can be reported,
for example, when the detected alarm condition is not currently
degrading the capacity of the managed object.
- warning: The Warning severity level indicates the detection of
a potential or impending service affecting fault, before any
significant effects have been felt. Action should be taken to
further diagnose (if necessary) and correct the problem in order
to prevent it from becoming a more serious service affecting fault.
- notification: The notification severity level indicates that
only a infomation to be report and it is either a fault or
a potential fault.
"
DEFVAL { notification }
::= { zxDslTrapHostEntry 7 }
----
zxDslSysIfCtrlTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslSysIfCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An (conceptual) table listing of zxDsl system interface extend attribute."
::= { zxDslCommon 34 }
zxDslSysIfCtrlEntry OBJECT-TYPE
SYNTAX ZxDslSysIfCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry (conceptual) table listing of zxDsl system interface extend attribute."
INDEX { ifIndex }
::= { zxDslSysIfCtrlTable 1 }
ZxDslSysIfCtrlEntry ::= SEQUENCE {
zxDslSysIfTrapCtrl PortList,
zxDslSysIfType Integer32
}
zxDslSysIfTrapCtrl OBJECT-TYPE
SYNTAX PortList
MAX-ACCESS read-write
STATUS current
DESCRIPTION "port trap control."
::= { zxDslSysIfCtrlEntry 1 }
zxDslSysIfType OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "If type ."
::= { zxDslSysIfCtrlEntry 2 }
--------------------------------------------------------------------------------
zxDslCluster OBJECT IDENTIFIER
::= { zxDslSysctrlObjects 5 }
zxDslStackModuleId OBJECT-TYPE
SYNTAX Integer32 ( 1 .. 24 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "moduleId of this ZXDSL in this stack system."
::= { zxDslCluster 1 }
zxDslStackModuleNum OBJECT-TYPE
SYNTAX Integer32 ( 1 .. 24 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "moduleNum of this ZXDSL in this stack system."
::= { zxDslCluster 2 }
zxDslStackModuleRole OBJECT-TYPE
SYNTAX INTEGER { master ( 1 ) , slave ( 2 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION "role of this ZXDSL in this stack system."
::= { zxDslCluster 3 }
zxDslStackTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslStackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The (conceptual) table listing of zxDsl system stack."
::= { zxDslCluster 4 }
zxDslStackEntry OBJECT-TYPE
SYNTAX ZxDslStackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry (conceptual) table listing of zxDsl system stack."
INDEX { zxDslStackIndex }
::= { zxDslStackTable 1 }
ZxDslStackEntry ::= SEQUENCE {
zxDslStackIndex Integer32,
zxDslStackIpAddr IpAddress,
zxDslStackRowStatus RowStatus
}
zxDslStackIndex OBJECT-TYPE
SYNTAX Integer32 ( 1 .. 24 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "stackid of zxDsl system."
::= { zxDslStackEntry 1 }
zxDslStackIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION "stack ip address of zxDsl system."
::= { zxDslStackEntry 2 }
zxDslStackRowStatus OBJECT-TYPE
SYNTAX RowStatus { active ( 1 ) , notInService ( 2 ) ,
notReady ( 3 ) , createAndGo ( 4 ) , createAndWait ( 5 ) ,
destroy ( 6 ) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This object indicates the status of this entry."
::= { zxDslStackEntry 3 }
--------------------------------------------------------------------------------
zxDslFtp OBJECT IDENTIFIER
::= { zxDslSysctrlObjects 7 }
zxDslFtpManagedObjectType OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 1 .. 16 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
Operation type, related with following operations.
port config file:PORT_INFO,DSL_PORT_INFO
startup config file:STARTUP_CONFIG
running config file:RUNNING_CONFIG
version download:COREI, COREF, PCSA, COREF2, WANB1, WANB, WANAB,
STUCA, LTC, ATUGA, IMAA, ATUGI, IMAB, ATUGB,
VTUCA, STUDB, gplus, gdmt, g2p512k, g2p1M,
ISUGB4, APPARM, SCCE, SCCH
patch download:PATCH
Localization file download(console and telnet): LOCAL_FILE
module config file:MODULE_FILE
"
::= { zxDslFtp 1 }
zxDslFtpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
The IP Address for the FTP server used for downloading
and/or uploading files."
::= { zxDslFtp 2 }
zxDslFtpUserName OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 1 .. 64 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The FTP username."
::= { zxDslFtp 3 }
zxDslFtpUserPwd OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 1 .. 64 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
The FTP User Password."
::= { zxDslFtp 4 }
zxDslFtpFilePath OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 1 .. 64 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
The FTP File Path, start from the root directory."
::= { zxDslFtp 5 }
zxDslFtpFileName OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 1 .. 64 ) )
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
The FTP file path and name."
::= { zxDslFtp 6 }
zxDslFtpLoadType OBJECT-TYPE
SYNTAX INTEGER { upload ( 1 ) , download ( 2 ) ,
versionDownloadAndOverwriteExisting ( 3 ) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION " Ftp load type."
::= { zxDslFtp 7 }
zxDslDownloadStatus OBJECT-TYPE
SYNTAX INTEGER { notstarted ( 1 ) , inprogress ( 2 ) , success ( 3 ) , masterfailed ( 4 ) , slavefailed ( 5 ) , allfailed ( 6 ) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION " Ftp operation status."
::= { zxDslFtp 8 }
zxDslFtpAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of IP Address for FTP server."
DEFVAL { 1 }
::= { zxDslFtp 9 }
zxDslFtpIpv6Address OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The IPv6 Ip Address for FTP server."
::= { zxDslFtp 10 }
zxDslFtpProtocolType OBJECT-TYPE
SYNTAX INTEGER
{
ftp(1),
sftp(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"zxDslFtpProtocolType is used to indicate the ftp protocol.
It includes two protocols: one is ftp and the other is sftp."
DEFVAL { ftp }
::= { zxDslFtp 11 }
--------------------------------------------------------------------------------
zxDslAddress OBJECT IDENTIFIER
::= { zxDslSysctrlObjects 8 }
zxDslOutBandIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
"
::= { zxDslAddress 1 }
zxDslOutBandIpMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
"
::= { zxDslAddress 2 }
zxDslOutBandMACAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
"
::= { zxDslAddress 3 }
zxDslInBandMACAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "
"
::= { zxDslAddress 4 }
zxDslInBandTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslInBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table of subnet parameters. There is one entry
available for each of the 'tmsL3InBandMaxRows'
supported IP subnets."
::= { zxDslAddress 5 }
zxDslInBandEntry OBJECT-TYPE
SYNTAX ZxDslInBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A list of subnet parameters."
INDEX { zxDslInBandIpAddr }
::= { zxDslInBandTable 1 }
ZxDslInBandEntry ::= SEQUENCE {
zxDslInBandIpAddr IpAddress,
zxDslInBandIpMask IpAddress,
zxDslInBandIpVid Integer32,
zxDslInBandIpName DisplayString,
zxDslInBandIpUseType INTEGER,
zxDslInBandIpRowStatus RowStatus
}
zxDslInBandIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "DURABLE:
The network management station uses this IP Address to talk
with the Agent on this subnet. This IP address logically
AND'ed with 'tmsL3InBandMask' yields the actual subnet
value for this subnet."
::= { zxDslInBandEntry 1 }
zxDslInBandIpMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION "DURABLE:
The subnet mask for this subnet. It contains 1's in the
bit positions for the net and subnet IDs and 0's in the
bit positions for host ID. The 1's must be contiguous,
starting with the left most bit."
::= { zxDslInBandEntry 2 }
zxDslInBandIpVid OBJECT-TYPE
SYNTAX Integer32 ( 0 .. 4094 )
MAX-ACCESS read-create
STATUS current
DESCRIPTION "DURABLE: { default=0:all }
For a L2/L3 hybrid switch, this object contains the actual
VLAN ID (VID) from 1 to 4094 or 0 if the VID is unassigned.
For a L3 only switch, this object contains the actual switch
interface from 1 to 4094 or 0 if unassigned.
Changing this object for this row causes all rows with the same
'tmsL3InBandIfIndex' as this row to be changed to this new
'tmsL3InBandVidIface' value."
::= { zxDslInBandEntry 3 }
zxDslInBandIpName OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-create
STATUS current
DESCRIPTION "DURABLE: { '':all )
A user reference name for this subnet."
::= { zxDslInBandEntry 4 }
zxDslInBandIpUseType OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
modem(2),
voip(3),
media(4),
normalSecondary(5),
layer3(6),
ieee1588(7),
serialPort(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Inband IP address type.
normal (1) - Inband IP address;
modem (2) - Modem management;
voip (3) - VoIP subnet IP address;
media (4) - VoIP media subnet IP address;
normalSecondary(5) - Secondary inband IP address;
layer3 (6) - Layer3 interface IP address;
ieee1588 (7) - IEEE 1588 IP address, just used by F829;
serialPort (8) - Serial port IP address, just used by F809;
"
::= { zxDslInBandEntry 5 }
zxDslInBandIpRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "DURABLE:
This object indicates the status of this entry. A row in this
table must be created using the createAndWait(5) action state
(i.e., createAndGo(4) is not supported). This object can only
be set to active(1) after all objects for this row are valid.
The 'tmsL3InBandName' is optional.
Note that the notInService(2) state is not supported. Objects
in this table row can be changed when this object is notReady(3)
or active(1)."
::= { zxDslInBandEntry 6 }
--------------------------------------------------------------------------------
zxDslIpv6Objects OBJECT IDENTIFIER
::= { zxDslSysctrlObjects 14 }
zxDslIpv6InBandTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslIpv6InBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table of subnet parameters. There is one entry
available for each of the 'tmsL3InBandMaxRows'
supported IP subnets."
::= { zxDslIpv6Objects 1 }
zxDslIpv6InBandEntry OBJECT-TYPE
SYNTAX ZxDslIpv6InBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A list of subnet parameters."
INDEX { zxDslIpv6InBandInetAddress }
::= { zxDslIpv6InBandTable 1 }
ZxDslIpv6InBandEntry ::= SEQUENCE {
zxDslIpv6InBandInetAddress InetAddress,
zxDslIpv6InBandInetAddressPrefixLength InetAddressPrefixLength,
zxDslIpv6InBandIpVid Integer32,
zxDslIpv6InBandIpName DisplayString,
zxDslIpv6InBandIpUseType INTEGER,
zxDslIpv6InBandIpRowStatus RowStatus
}
zxDslIpv6InBandInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "DURABLE:
The network management station uses this IP Address to talk
with the Agent on this subnet. This IP address logically
AND'ed with 'tmsL3InBandMask' yields the actual subnet
value for this subnet."
::= { zxDslIpv6InBandEntry 1 }
zxDslIpv6InBandInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-create
STATUS current
DESCRIPTION "the prefix length of inband inet address."
::= { zxDslIpv6InBandEntry 2 }
zxDslIpv6InBandIpVid OBJECT-TYPE
SYNTAX Integer32 ( 0 .. 4094 )
MAX-ACCESS read-create
STATUS current
DESCRIPTION "DURABLE: { default=0:all }
For a L2/L3 hybrid switch, this object contains the actual
VLAN ID (VID) from 1 to 4094 or 0 if the VID is unassigned.
For a L3 only switch, this object contains the actual switch
interface from 1 to 4094 or 0 if unassigned.
Changing this object for this row causes all rows with the same
'tmsL3InBandIfIndex' as this row to be changed to this new
'tmsL3InBandVidIface' value."
::= { zxDslIpv6InBandEntry 3 }
zxDslIpv6InBandIpName OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 16 ) )
MAX-ACCESS read-create
STATUS current
DESCRIPTION "DURABLE: { '':all )
A user reference name for this subnet."
::= { zxDslIpv6InBandEntry 4 }
zxDslIpv6InBandIpUseType OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
modem(2),
voip(3),
media(4),
normalSecondary(5),
layer3(6),
ieee1588(7),
serialPort(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"IPv6 Inband IP address type.
normal (1) - Inband IP address;
Modem (2) - Modem management;
voip (3) - VoIP subnet IP address;
media (4) - VoIP media subnet IP address;
normalSecondary(5) - Secondary inband IP address;
layer3 (6) - Layer3 interface IP address;
ieee1588 (7) - IEEE 1588 IP address, just used by F829;
serialPort (8) - Serial port IP address, just used by F809;
"
::= { zxDslIpv6InBandEntry 5 }
zxDslIpv6InBandIpRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "DURABLE:
This object indicates the status of this entry. A row in this
table must be created using the createAndWait(5) action state
(i.e., createAndGo(4) is not supported). This object can only
be set to active(1) after all objects for this row are valid.
The 'tmsL3InBandName' is optional.
Note that the notInService(2) state is not supported. Objects
in this table row can be changed when this object is notReady(3)
or active(1)."
::= { zxDslIpv6InBandEntry 6 }
zxDslIpv6TrapHostTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslIpv6TrapHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table, which provides Trap target."
::= { zxDslIpv6Objects 2 }
zxDslIpv6TrapHostEntry OBJECT-TYPE
SYNTAX ZxDslIpv6TrapHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ""
INDEX { zxDslIpv6TrapHostIpAddr }
::= { zxDslIpv6TrapHostTable 1 }
ZxDslIpv6TrapHostEntry ::= SEQUENCE {
zxDslIpv6TrapHostIpAddr InetAddress,
zxDslIpv6TrapHostSnmpVer Integer32,
zxDslIpv6TrapHostCommunity DisplayString,
zxDslIpv6TrapHostIsZteNmsSever TruthValue,
zxDslIpv6TrapHostEventType BITS,
zxDslIpv6TrapHostMinEventLevel INTEGER,
zxDslIpv6TrapHostRowStatus RowStatus
}
zxDslIpv6TrapHostIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION ""
::= { zxDslIpv6TrapHostEntry 1 }
zxDslIpv6TrapHostSnmpVer OBJECT-TYPE
SYNTAX Integer32 ( 0 .. 1 )
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslIpv6TrapHostEntry 2 }
zxDslIpv6TrapHostCommunity OBJECT-TYPE
SYNTAX DisplayString ( SIZE ( 0 .. 64 ) )
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslIpv6TrapHostEntry 3 }
zxDslIpv6TrapHostIsZteNmsSever OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If or not it is a zte's nms.
true(1): it is a zte's nms;
false(2): it is not a zte's nms.
"
::= { zxDslIpv6TrapHostEntry 4 }
zxDslIpv6TrapHostEventType OBJECT-TYPE
SYNTAX BITS {
equipmentEvent(0),
qualityOfServiceEvent(1),
communicationsEvent(2),
environmentEvent(3),
processingErrorEvent(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The event type that a reciever expects.
The event type are defined in ITU-T X.733.
- equipment event type:
An event of this type is principally
associated with an equipment fault;
- quality of service event type:
An event of this type is
principally associated with a degradation in the quality of a service;
- communications event type:
An event of this type is principally
associated with the procedures and/or processes required to convey
information from one point to another;
- environmental event type:
An event of this type is principally
associated with a condition relating to an enclosure in which the
equipment resides.
- processing error event type:
An event of this type is
principally associated with a software or processing fault;
"
DEFVAL { { equipmentEvent,qualityOfServiceEvent,communicationsEvent,
environmentEvent,processingErrorEvent } }
::= { zxDslIpv6TrapHostEntry 5 }
zxDslIpv6TrapHostMinEventLevel OBJECT-TYPE
SYNTAX INTEGER {
cleared(0),
critical(1),
major(2),
minor(3),
warning(4),
notification(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The min event level that a reciever expects.If the actual event
level is more serious then this value,the event will be sent to
Event Reciever. For example,if this value is warning(4),all the
events that the level in cleared(0),critical(1),major(2),minor(3),
warning(4) will be sent,but notification(5) will not be sent.
The event levels are defined in ITU-T X.733.
- cleared: The Cleared severity level indicates the clearing of
one or more previously reported alarms. This alarm clears all
alarms for this managed object that have the same Alarm type,
Probable cause and Specific problems (if given).
Multiple associated notifications may be cleared by using
the Correlated notifications parameter (defined below).
This Recommendation | International Standard does not require that
the clearing of previously reported alarms be reported.
Therefore, a managing system cannot assume that the absence of
an alarm with the Cleared severity level means that the condition
that caused the generation of previous alarms is still present.
Managed object definers shall state if, and under which
conditions, the Cleared severity level is used.
- critical: The Critical severity level indicates that a service
affecting condition has occurred and an immediate corrective action
is required. Such a severity can be reported, for example, when
a managed object becomes totally out of service and its capability
must be restored.
- major: The Major severity level indicates that a service
affecting condition has developed and an urgent corrective action
is required. Such a severity can be reported, for example, when
there is a severe degradation in the capability of the managed
object and its full capability must be restored.
- minor: The Minor severity level indicates the existence of
a non-service affecting fault condition and that corrective action
should be taken in order to prevent a more serious (for example,
service affecting) fault. Such a severity can be reported,
for example, when the detected alarm condition is not currently
degrading the capacity of the managed object.
- warning: The Warning severity level indicates the detection of
a potential or impending service affecting fault, before any
significant effects have been felt. Action should be taken to
further diagnose (if necessary) and correct the problem in order
to prevent it from becoming a more serious service affecting fault.
- notification: The notification severity level indicates that
only a infomation to be report and it is either a fault or
a potential fault.
"
DEFVAL { notification }
::= { zxDslIpv6TrapHostEntry 6 }
zxDslIpv6TrapHostRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslIpv6TrapHostEntry 30 }
zxDslIpv6GlobalObjects OBJECT IDENTIFIER ::= { zxDslIpv6Objects 3 }
zxDslIpv6Enable OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable/Disable IPv6."
DEFVAL { disable }
::= { zxDslIpv6GlobalObjects 1}
zxDslIpv6OutbandAddress OBJECT IDENTIFIER ::= { zxDslIpv6Objects 4 }
zxDslIpv6OutBandInetAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Outband inet address."
::= { zxDslIpv6OutbandAddress 1 }
zxDslIpv6OutBandInetAddrPfxLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Outband inet address prefix length."
::= { zxDslIpv6OutbandAddress 2 }
--------------------------------------------------------------------------------
zxDslLocalizationObjects OBJECT IDENTIFIER
::= { zxDslSysctrlObjects 15 }
zxDslLocalizationGlobalObjects OBJECT IDENTIFIER
::= { zxDslLocalizationObjects 1 }
zxDslLanguage OBJECT-TYPE
SYNTAX INTEGER
{
english(1),
chinese(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The language for console and telnet."
DEFVAL { english }
::= { zxDslLocalizationGlobalObjects 1 }
zxDslLocalizationFileTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslLocalizationFileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes the localization file information
for console and telnet."
::= { zxDslLocalizationObjects 2 }
zxDslLocalizationFileEntry OBJECT-TYPE
SYNTAX ZxDslLocalizationFileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in zxDslLocalizationFileTable."
INDEX {zxDslLocalizationFileType}
::= { zxDslLocalizationFileTable 1 }
ZxDslLocalizationFileEntry ::= SEQUENCE {
zxDslLocalizationFileType INTEGER,
zxDslLocalizationFileVersion DisplayString,
zxDslLocalizationFileSize Unsigned32,
zxDslLocalizationFileCreateTime DisplayString,
zxDslLocalizationFileAdminStatus INTEGER
}
zxDslLocalizationFileType OBJECT-TYPE
SYNTAX INTEGER
{
english(1),
chinese(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Localization file type."
::= { zxDslLocalizationFileEntry 1 }
zxDslLocalizationFileVersion OBJECT-TYPE
SYNTAX DisplayString (SIZE( 0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version number of the localization file."
::= { zxDslLocalizationFileEntry 2 }
zxDslLocalizationFileSize OBJECT-TYPE
SYNTAX Unsigned32
UNITS "byte"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version length of the localization file."
::= { zxDslLocalizationFileEntry 3 }
zxDslLocalizationFileCreateTime OBJECT-TYPE
SYNTAX DisplayString(SIZE( 0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Create time of the localization file.The format is
yyyymmdd HHMMSS.For example,20100707 131527"
::= { zxDslLocalizationFileEntry 4 }
zxDslLocalizationFileAdminStatus OBJECT-TYPE
SYNTAX INTEGER
{
delete(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Delete localization file."
::= { zxDslLocalizationFileEntry 10 }
--------------------------------------------------------------------------------
zxDslModuleFileObjects OBJECT IDENTIFIER
::= { zxDslSysctrlObjects 16 }
zxDslModuleFileGlobalObjects OBJECT IDENTIFIER
::= { zxDslModuleFileObjects 1 }
zxDslModuleFileStatus OBJECT-TYPE
SYNTAX INTEGER
{
notExist(1),
loadSucceeded(2),
loadFailed(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the module file:
notExist(1) - Module file does not exist.
loadSucceeded(2) - Load module file succeeded.
loadFailed(3) - Load module file failed.
"
DEFVAL { notExist }
::= { zxDslModuleFileGlobalObjects 1 }
zxDslModuleFileInfo OBJECT-TYPE
SYNTAX DisplayString (SIZE( 1..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The information of the module file which includes NE version name,
NE version No., module file version No. and module file build time.
"
::= { zxDslModuleFileGlobalObjects 2 }
zxDslEraseModuleFile OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Value 1 means to erase the module file."
::= { zxDslModuleFileGlobalObjects 3 }
--------------------------------------------------------------------------------
zxDslNmsAccessCtrl OBJECT IDENTIFIER ::= { zxDslSysctrlObjects 9 }
zxDslCommunityConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslCommunityConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of SNMPv1/v2c community string configuration."
::= { zxDslNmsAccessCtrl 1 }
zxDslCommunityConfEntry OBJECT-TYPE
SYNTAX ZxDslCommunityConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of community strings."
INDEX { zxDslCommunityConfCommunity }
::= { zxDslCommunityConfTable 1 }
ZxDslCommunityConfEntry ::= SEQUENCE {
zxDslCommunityConfCommunity DisplayString,
zxDslCommunityConfPermission INTEGER,
zxDslCommunityConfViewName DisplayString,
zxDslCommunityConfRowStatus RowStatus
}
zxDslCommunityConfCommunity OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"DURABLE: { 'public','':all }
The SNMPv1/v2c community name string.
Name must begin with alphabetic character or '_' and '@' shouldn't
be used in community string.
Duplicate community names are not allowed in this table.
Note that a null string is not a valid community name
(i.e., a null string forces 'zxDslCommunityConfRowStatus'
to 'notReady(3)')."
::= { zxDslCommunityConfEntry 1 }
zxDslCommunityConfPermission OBJECT-TYPE
SYNTAX INTEGER {
readOnly(1),
readWrite(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"DURABLE: { readWrite:all }
This object specifies the type of access allowed. 'readOnly(1)'
allows GET operations (i.e., GET, GET-NEXT, GET-BULK) and
'readWrite(2)' allows both GET and SET operations."
::= { zxDslCommunityConfEntry 2 }
zxDslCommunityConfViewName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"
This object is reserved now.
DURABLE: { 'internet':all }
At runtime (i.e., not when this object is SET), this view name
is compared to the 'vacmViewTreeFamilyViewName' in the
'vacmViewTreeFamilyTable' (see RFC2575). If a match is
found and the varbind(s) specify valid object type and instance,
the 'zxDslCommunityConfPermission' privilege is permitted.
Note that a null string is not a valid view name value.
Also note that the value of this object does not have to match
an existing entry in the 'vacmViewTreeFamilyTable' (if no match,
no access is allowed).
Note that the factory default value for this object is 'internet',
which allows access to the subtree under '1.3.6.1'."
::= { zxDslCommunityConfEntry 3 }
zxDslCommunityConfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"DURABLE:
This object indicates the status of this entry. A row in this
table can be created using the 'createAndGo(4)' (i.e., all
parameters must be valid - supplied in a single SNMP PDU or have
default values).
Any object in a conceptual row can be modified independent of the
value of this object (e.g., can be changed while 'active(1)')."
::= { zxDslCommunityConfEntry 4 }
--------------------------------------------------------------------------------
-- Ntp
--------------------------------------------------------------------------------
zxDslSntp OBJECT IDENTIFIER ::= { zxDslSysctrlObjects 10 }
zxDslSntpEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable/disable NTP in this system."
DEFVAL { disable }
::= { zxDslSntp 1}
zxDslSntpServerIp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The NTP server's IP address "
::= { zxDslSntp 2}
zxDslSntpPollInterval OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The NTP server's fetch time's interval time, the default is 64"
DEFVAL { 64 }
::= { zxDslSntp 3}
zxDslSntpStratum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The local NTP server 's stratum.
If it is 16,then it means that this device has not synchronied time,
and it is a invalid value. "
::= { zxDslSntp 5}
zxDslSntpSynchStatus OBJECT-TYPE
SYNTAX INTEGER
{
alreadySyn(1),
neverSyn(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The NTP server whether is synchronized or not "
::= { zxDslSntp 6}
zxDslSntpSlaveServerIp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The slave NTP server's IP address "
::= { zxDslSntp 7}
zxDslSntpCurrTryingSynchServerIp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The NTP server's IP which is being tried to synchronize time now."
::= { zxDslSntp 8}
zxDslSntpLastSynchronizedServerIP OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The NTP server's IP address of last ntp synchronization."
::= { zxDslSntp 9}
zxDslSysSntpCurrentOffset OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Time offset to the current selected reference time source.
"
::= { zxDslSntp 10 }
zxDslSysSntpOffsetAlarmThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The alarm threshold of NTP time offset to the current selected
reference time source.When this threshold is across,the trap
zxDslSysSntpOffsetOverThreshTrap should be sent to a manager.
"
DEFVAL { 7 }
::= { zxDslSntp 11 }
zxDslOpticalPower OBJECT IDENTIFIER ::= { zxDslSysctrlObjects 11 }
zxDslOpticalPowerRx OBJECT-TYPE
SYNTAX DisplayString
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Received optical power"
::= { zxDslOpticalPower 1}
zxDslOpticalPowerTx OBJECT-TYPE
SYNTAX DisplayString
UNITS "dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Transmitted optical power"
::= { zxDslOpticalPower 2}
zxDslVoipDhcp OBJECT IDENTIFIER ::= { zxDslSysctrlObjects 12 }
zxDslVoipDhcpEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VOIP DHCP status. The IP subnet for VOIP should be configed first."
DEFVAL { disable }
::= { zxDslVoipDhcp 1 }
zxDslVoipDhcpIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address for VOIP when zxDslVoipDhcpEnable is enable.
When zxDslVoipDhcpEnable is disable, VOIP IP address should be getted from IP subnet table."
::= { zxDslVoipDhcp 2 }
zxDslVoipDhcpIpMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP mask for VOIP when zxDslVoipDhcpEnable is enable.
When zxDslVoipDhcpEnable is disable, VOIP IP mask should be getted from IP subnet table."
::= { zxDslVoipDhcp 3 }
zxDslVoipDhcpRoute OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The route for VOIP when zxDslVoipDhcpEnable is enable.
When zxDslVoipDhcpEnable is disable, VOIP route should be getted from IP route table."
::= { zxDslVoipDhcp 4 }
zxDslVoipDhcpOption60Enable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VOIP DHCP Option60 status. "
DEFVAL { enable }
::= { zxDslVoipDhcp 5 }
zxDslVoipDhcpOption60Vendor OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VOIP DHCP Option60 Vendor. "
::= { zxDslVoipDhcp 6 }
zxDslVoipDhcpOption60Category OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VOIP DHCP Option60 Category. "
::= { zxDslVoipDhcp 7 }
zxDslVoipDhcpOption60Model OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VOIP DHCP Option60 Model. "
::= { zxDslVoipDhcp 8}
zxDslVoipDhcpOption60Version OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VOIP DHCP Option60 Version. "
::= { zxDslVoipDhcp 9 }
zxDslVoipDhcpReRequestEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When zxDslVoipDhcpReRequestEnable is enable, device will
re-request an IP address by DHCP as VoIP service is broken.
This object is valid when zxDslVoipDhcpEnable is enable."
DEFVAL { disable }
::= {zxDslVoipDhcp 10 }
zxDslVoipDhcpReRequestInterval OBJECT-TYPE
SYNTAX Integer32(1..20)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The interval that device re-requests an IP address after VoIP
service is broken.
This object is valid when zxDslVoipDhcpReRequestEnable is enable."
DEFVAL { 10 }
::= {zxDslVoipDhcp 11 }
zxDslSyslog OBJECT IDENTIFIER ::= { zxDslSysctrlObjects 13 }
zxDslSyslogGlobalObjects OBJECT IDENTIFIER ::= {zxDslSyslog 1}
zxDslSyslogFacility OBJECT-TYPE
SYNTAX Integer32(0..23)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The syslog message facility. The priority value of PRI is calculated by first multiplying
the Facility number by 8 and then adding the numerical value of the Severity.
Numerical Code Facility
0 kernel messages
1 user-level messages
2 mail system
3 system daemons
4 security/authorization messages (note 1)
5 messages generated internally by syslogd
6 line printer subsystem
7 network news subsystem
8 UUCP subsystem
9 clock daemon (note 2)
10 security/authorization messages (note 1)
11 FTP daemon
12 NTP subsystem
13 log audit (note 1)
14 log alert (note 1)
15 clock daemon (note 2)
16 local use 0 (local0)
17 local use 1 (local1)
18 local use 2 (local2)
19 local use 3 (local3)
20 local use 4 (local4)
21 local use 5 (local5)
22 local use 6 (local6)
23 local use 7 (local7)
More information, please refer to rfc3164.
"
::= { zxDslSyslogGlobalObjects 1 }
zxDslSyslogSeverity OBJECT-TYPE
SYNTAX Integer32(0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The syslog message severity, The priority value of PRI is calculated by first multiplying
the Facility number by 8 and then adding the numerical value of the Severity.
Numerical Code Severity
0 Emergency: system is unusable
1 Alert: action must be taken immediately
2 Critical: critical conditions
3 Error: error conditions
4 Warning: warning conditions
5 Notice: normal but significant condition
6 Informational: informational messages
7 Debug: debug-level messages
More information, please refer to rfc3164.
"
::= { zxDslSyslogGlobalObjects 2 }
zxDslSyslogSrcPort OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The syslog source udp port. "
::= { zxDslSyslogGlobalObjects 3 }
zxDslSyslogCmdLogEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Enable/Disable the cmd log in syslog. "
::= { zxDslSyslogGlobalObjects 4 }
zxDslSyslogSnmpLogEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Enable/Disable the snmp log in syslog. "
::= { zxDslSyslogGlobalObjects 5 }
zxDslSyslogAlarmLogEnable OBJECT-TYPE
SYNTAX INTEGER{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Enable/Disable the alarm log in syslog. "
::= { zxDslSyslogGlobalObjects 6 }
zxDslSyslogAlarmLogLevel OBJECT-TYPE
SYNTAX Integer32(0..7)
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The alarm log level in syslog. "
::= { zxDslSyslogGlobalObjects 7 }
zxDslSyslogHostTable OBJECT-TYPE
SYNTAX SEQUENCE OF ZxDslSyslogHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "syslog host table."
::= { zxDslSyslog 2 }
zxDslSyslogHostEntry OBJECT-TYPE
SYNTAX ZxDslSyslogHostEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in zxDslSyslogHostTable."
INDEX { zxDslSyslogHostIpAddr }
::= { zxDslSyslogHostTable 1 }
ZxDslSyslogHostEntry ::= SEQUENCE {
zxDslSyslogHostIpAddr IpAddress,
zxDslSyslogDesPort Integer32,
zxDslSyslogHostRowStatus RowStatus
}
zxDslSyslogHostIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The syslog server ip address. "
::= { zxDslSyslogHostEntry 1 }
zxDslSyslogDesPort OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The syslog destination udp port. "
::= { zxDslSyslogHostEntry 2 }
zxDslSyslogHostRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION ""
::= { zxDslSyslogHostEntry 10 }
--------------------------------------------------------------------------------
-- definition of sysctrl traps.
zxDslPrimaryCtrlCardSwapped NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A zxDslPrimaryCtrlCardSwapped trap indicates that the main control
card has swapped to slave card."
::= { zxDslSysctrlTrapObjects 1 }
zxDslCardUp NOTIFICATION-TYPE
OBJECTS { zxDslBoardAdminStatus, zxDslBoardOperStatus }
STATUS current
DESCRIPTION
"A zxDslCardUp trap indicates that the agent has detected that the
card has been online."
::= { zxDslSysctrlTrapObjects 2 }
zxDslCardDown NOTIFICATION-TYPE
OBJECTS { zxDslBoardAdminStatus, zxDslBoardOperStatus }
STATUS current
DESCRIPTION
"A zxDslCardDown trap indicates that the agent has detected that the
card has been offline."
::= { zxDslSysctrlTrapObjects 3 }
zxDslCpuLoadAlarm NOTIFICATION-TYPE
OBJECTS { zxDslBoardCpuLoad, zxDslBoardCpuLoadThreshhold }
STATUS current
DESCRIPTION
"A zxDslCpuLoadAlarm trap indicates that the agent has detected that the
zxDslCardCPULoad object of one card has exceeded the configured threshhold value of
zxDslBoardCpuLoadThreshhold."
::= { zxDslSysctrlTrapObjects 4 }
zxDslCpuLoadAlarmCleard NOTIFICATION-TYPE
OBJECTS { zxDslBoardCpuLoad, zxDslBoardCpuLoadThreshhold }
STATUS current
DESCRIPTION
"A zxDslCpuLoadAlarmCleard trap indicates that the agent has detected that the
zxDslCardCPULoad object of one card has less than the configured threshhold value of
zxDslBoardCpuLoadThreshhold."
::= { zxDslSysctrlTrapObjects 5 }
zxDslMemoryOverLoad NOTIFICATION-TYPE
OBJECTS { zxDslBoardMemUsage, zxDslBoardMemUsageThreshhold }
STATUS current
DESCRIPTION
"A zxDslMemoryOverLoad trap indicates that the agent has detected that the
zxDslCardMemUsage object of one card has exceeded the configured threshhold value of
zxDslBoardMemUsageThreshhold."
::= { zxDslSysctrlTrapObjects 6 }
zxDslMemoryAlarmCleard NOTIFICATION-TYPE
OBJECTS { zxDslBoardMemUsage, zxDslBoardMemUsageThreshhold }
STATUS current
DESCRIPTION
"A zxDslMemoryAlarmCleard trap indicates that the agent has detected that the
zxDslCardMemUsage object of one card has less than the configured threshhold value of
zxDslBoardMemUsageThreshhold."
::= { zxDslSysctrlTrapObjects 7 }
-- env trap
zxDslEnvTrapGroup OBJECT IDENTIFIER ::= { zxDslSysctrlTrapObjects 8 }
zxDslEnvTempExceeded NOTIFICATION-TYPE
OBJECTS {
zxDslEnvChassisTemperature,
zxDslEnvTemperatureThreshold
}
STATUS current
DESCRIPTION
"A temperature inside the chassis has exceeded
normal operating temperature zxDslEnvTemperatureThreshold.
The zxDslEnvChassisTemperature object identifies the current status."
::= { zxDslEnvTrapGroup 1 }
zxDslEnvTempNormal NOTIFICATION-TYPE
OBJECTS {
zxDslEnvChassisTemperature,
zxDslEnvTemperatureThreshold
}
STATUS current
DESCRIPTION
"A temperature inside the chassis has returned to
normal operating temperature zxDslEnvTemperatureThreshold.
The zxDslEnvChassisTemperature object identifies the current status."
::= { zxDslEnvTrapGroup 2 }
zxDslEnvFanFailed NOTIFICATION-TYPE
OBJECTS {
zxDslEnvFanAdminstatus,
zxDslEnvFanOperstatus }
STATUS current
DESCRIPTION
"A Fan tray on the device has failed. The
zxDslEnvFanOperstatus object identifies the failed fan Operstatus."
::= { zxDslEnvTrapGroup 3 }
zxDslEnvFanRecovered NOTIFICATION-TYPE
OBJECTS {
zxDslEnvFanAdminstatus,
zxDslEnvFanOperstatus }
STATUS current
DESCRIPTION
"A Fan tray on the device has recovered
after failure. The zxDslEnvFanOperstatus object identifies
the recovered Fan Operstatus."
::= { zxDslEnvTrapGroup 4 }
zxDslEnvLossOfPower NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"This is device dying gasp event.It is generated when the device is
power off or power failure."
::= { zxDslEnvTrapGroup 5 }
zxDslEnvSwitchFailed NOTIFICATION-TYPE
OBJECTS {
zxDslEnvDeviceId,
zxDslEnvSwitchNormalStatus,
zxDslEnvSwitchCurrentStatus
}
STATUS current
DESCRIPTION
"It is generated when the switch is Faild."
::= { zxDslEnvTrapGroup 6 }
zxDslEnvSwitchRecovered NOTIFICATION-TYPE
OBJECTS {
zxDslEnvDeviceId,
zxDslEnvSwitchNormalStatus,
zxDslEnvSwitchCurrentStatus
}
STATUS current
DESCRIPTION
"It is generated when the switch is Recovered."
::= { zxDslEnvTrapGroup 7 }
zxDslEnvExteriorPowerFailed NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It is generated when the Exterior Power is Faild."
::= { zxDslEnvTrapGroup 8 }
zxDslEnvExteriorPowerRecovered NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It is generated when the Exterior Power is Recovered."
::= { zxDslEnvTrapGroup 9 }
zxDslEnvBatteriesVoltageFailed NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It is generated when the Batteries Voltage is Faild."
::= { zxDslEnvTrapGroup 10 }
zxDslEnvBatteriesVoltageRecovered NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It is generated when the Batteries Voltage is Recovered."
::= { zxDslEnvTrapGroup 11 }
zxDslEnvPowerFailed NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It is generated when the Power is Faild."
::= { zxDslEnvTrapGroup 12 }
zxDslEnvPowerRecovered NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It is generated when the Power is Recovered."
::= { zxDslEnvTrapGroup 13 }
zxDslEnvMonitorInterfaceLinkDown NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It indicates that the agent has detected that the
link at the enviroment monitoring inerface has been down."
::= { zxDslEnvTrapGroup 14 }
zxDslEnvMonitorInterfaceLinkUp NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"It indicates that the agent has detected that the
link at the enviroment monitoring inerface has been up."
::= { zxDslEnvTrapGroup 15 }
zxDslTempUnderThreshTrap NOTIFICATION-TYPE
OBJECTS {
zxDslEnvChassisTemperature,
zxDslEnvTemperatureLowerThreshold
}
STATUS current
DESCRIPTION
"It indicates that the zxDslEnvChassisTemperature is lower
than zxDslEnvTemperatureLowerThreshold."
::= { zxDslEnvTrapGroup 16 }
zxDslTempUnderThreshTrapCleared NOTIFICATION-TYPE
OBJECTS {
zxDslEnvChassisTemperature,
zxDslEnvTemperatureLowerThreshold
}
STATUS current
DESCRIPTION
"It indicates that the zxDslTempUnderThreshTrap has Cleared."
::= { zxDslEnvTrapGroup 17 }
zxDslEnvFanFaultStateChangedTrap NOTIFICATION-TYPE
OBJECTS {
zxDslEnvFanFaultInfo,
zxDslEnvFanTotalNumber
}
STATUS current
DESCRIPTION
"This trap signifies that fault state of a fan has been changed.
zxDslEnvFanFailedInfo indicates the failed fan list.
zxDslEnvFanTotalNumber indicates the total number of fans.
."
::= { zxDslEnvTrapGroup 18 }
--- Port Traps
zxDslIfUplinkUp NOTIFICATION-TYPE
OBJECTS { ifAdminStatus, ifOperStatus, ifType }
STATUS current
DESCRIPTION
"The operational status of uplink interface changes to up."
::= { zxDslSysctrlTrapObjects 20 }
zxDslIfUplinkDown NOTIFICATION-TYPE
OBJECTS { ifAdminStatus, ifOperStatus, ifType }
STATUS current
DESCRIPTION
"The operational status of uplink interface changes to down."
::= { zxDslSysctrlTrapObjects 21 }
zxDslIfAccesslinkUp NOTIFICATION-TYPE
OBJECTS { ifAdminStatus, ifOperStatus, ifType }
STATUS current
DESCRIPTION
"The operational status of access link interface changes to up."
::= { zxDslSysctrlTrapObjects 22 }
zxDslIfAccesslinkDown NOTIFICATION-TYPE
OBJECTS { ifAdminStatus, ifOperStatus, ifType }
STATUS current
DESCRIPTION
"The operational status of access link interface changes to down."
::= { zxDslSysctrlTrapObjects 23 }
zxDslUnexpectedCardTypePlugin NOTIFICATION-TYPE
OBJECTS { zxDslBoardType }
STATUS current
DESCRIPTION
"A zxDslUnexpectedCardTypePlugin trap indicates that the card plug
in the given slot is unexpected.
For example, the ethernet user card can be plug in slot 2 of F821
NE with HSMV, when ei8e card be pluged in other slot, this alarm
will be generated."
REFERENCE "F821"
::= { zxDslSysctrlTrapObjects 24 }
zxDslUnexpectedCardTypePluginCleared NOTIFICATION-TYPE
OBJECTS { zxDslBoardType }
STATUS current
DESCRIPTION
"A zxDslUnexpectedCardTypePluginCleared trap indicates that the
unexpected card plug-in is Recovered.
For example, when ei8e card be unpluged from slot 3 of F821 NE
with HSMV, this clear trap will be generated. "
REFERENCE "F821"
::= { zxDslSysctrlTrapObjects 25 }
zxDslMaxPortNumPerSlotChanged NOTIFICATION-TYPE
OBJECTS { zxDslSysMaxPortNumPerSlot }
STATUS current
DESCRIPTION
"A zxDslMaxPortNumPerSlotChanged trap indicates that the value of
zxDslSysMaxPortNumPerSlot changed."
::= { zxDslSysctrlTrapObjects 26 }
zxDslCardChipDown NOTIFICATION-TYPE
OBJECTS { zxDslBoardType }
STATUS current
DESCRIPTION
"A zxDslCardChipDown trap indicates that the card is in abnormal
status."
::= { zxDslSysctrlTrapObjects 27 }
zxDslCardChipDownCleared NOTIFICATION-TYPE
OBJECTS { zxDslBoardType }
STATUS current
DESCRIPTION
"A zxDslCardChipDownCleared trap indicates that the abnormal card is
Recovered."
::= { zxDslSysctrlTrapObjects 28 }
--------------------------------------------------------------------------------
-- Ntp Trap
--------------------------------------------------------------------------------
zxDslSysSntpTrapGroup OBJECT IDENTIFIER ::= { zxDslSysctrlTrapObjects 50 }
zxDslSysSntpOffsetOverThreshTrap NOTIFICATION-TYPE
OBJECTS { zxDslSysSntpCurrentOffset,
zxDslSysSntpOffsetAlarmThreshold }
STATUS current
DESCRIPTION
"zxDslSysSntpOffsetAlarmThreshold is reached."
::= { zxDslSysSntpTrapGroup 1 }
zxDslSysSntpOffsetUnderThreshTrap NOTIFICATION-TYPE
OBJECTS { zxDslSysSntpCurrentOffset,
zxDslSysSntpOffsetAlarmThreshold }
STATUS current
DESCRIPTION
" zxDslSysSntpCurrentOffset is below zxDslSysSntpOffsetAlarmThreshold.
"
::= { zxDslSysSntpTrapGroup 2 }
zxDslSysSntpSynchFailed NOTIFICATION-TYPE
OBJECTS { zxDslSntpCurrTryingSynchServerIp }
STATUS current
DESCRIPTION
"Faied to synchronize time from SNTP server."
::= { zxDslSysSntpTrapGroup 3 }
zxDslSysSntpSynchFailedCleard NOTIFICATION-TYPE
OBJECTS { zxDslSntpCurrTryingSynchServerIp }
STATUS current
DESCRIPTION
"Cleared the alarm of zxDslSysSntpSynchFailed."
::= { zxDslSysSntpTrapGroup 4 }
zxDslSysCompatible OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The compatibility of DSLAM. Every bit denotes the
compatibility of some function. If the value of the
bit is 1, the related function has compatible problem.
The related function of the first bit is the naming
rules of string.
bit 1: QoS Flow Policy of NE supports CCoS.
bit 2: zxDslInBandIpUseType. value 1 of this bit means normalSecondary(5), 0 means normalSecondary(3).
bit 3: zxDslSyslog. value 1 means use zxDslSyslogHostTable, value 0 means just scalar value for Finland test.
bit 4: zxDslTrapHostTable. value 1 means support event level and type.
bit 5: QoS Queue Expand,include zxDslQosSchedulerID and zxDslQos8021p2CosQPortNumber. value 1 means zxDslQosSchedulerID
and zxDslQos8021p2CosQPortNumber support UNI-ETCA.
bit 6: Different unit of ifLastChange, value 1 means 10 millisecond, 0 means 1 second.
bit 7: value 1 means support IAP Igmp and Multicast MIB.
bit 8: value 1 means support a200mgcinfo in a200mgccfgTable.
bit 9: value 1 means support zxDslPortLocationIfaceDhcpv6Enable and Dhcpv6OptionTrust in zxDslPortLocationIfaceTable.
bit 10: value 1 means support IPV6.
bit 11: value 1 means support zxAnMvlanHostVersion.
bit 12: For port egress QoS policy, value 1 means support zxDslQosPortEgressPolicyTable.
bit 13: value 1 means support zxDslPortLocationIfaceCircuitIdSyntaxPrfName and zxDslPortLocationIfaceActualCircuitId
in zxDslPortLocationIfaceTable.
bit 14: value 1 means support VdslDataRateTrap.
bit 15: value 1 means support zxDslDhcpv6PvcIfIpSourceGuardEnable,zxDslDhcpv6IfDhcpSnoopingEnable and zxDslDhcpv6IfDhcpSnoopingLimit
for DHCPv6 in zxDslDhcpPvcIfTable and zxDslDhcpIfTable.
bit 16: value 1 means flowcontrol inndependent to auto-negotiation.
bit 17: value 1 means zxDslFtpManagedObjectType support DSL_PORT_INFO.
bit 18: value 1 means support zxDslMacAddressExtTable.
bit 19: value 1 means support pccw DSL_PORT_INFO (Modem Vendor, Modem Serial Number, Modem Firmware).
bit 20: value 1 means support aturInitFailureTrapEnable of ADSL and atucInitFailureTrapEnable and aturInitFailureTrapEnable of VDSL.
bit 21: value 1 means support zxVoiceFlowStatisticRecordTime in zxVoipVoiceFlowStatisticTable.
bit 22: value 1 means support a200sipproxysvrPort in a200sipproxysvrTable and the range of a200sipproxysvrindex is 1..4.
bit 23: value 1 means support zxDslPortPppoeSyntaxPrfName and zxDslPortActPppoeCircuitId in zxDslPortLocationIfaceTable.
bit 24: value 1 means support a200slcFeedCurrent in a200slcTable and
msagSlcHighImpedacneOper and msagSlcNoneHighImpedanceOper in msagSlcCtrlTable.
bit 25: value 1 means support a200sipproxysvrInfo and a200sipproxysvrDomainName in a200sipproxysvrTable.
bit 26: value 1 means support G.INP for VDSL Line.
bit 27: value 1 means support G.INP for ADSL Line.
bit 28: value 1 means support DPBO,PSDMASK(PSD mask)
and TXREFVN(transmitter referred virtual noise)
for ADSL Line.
bit 29: value 1 means support zxDslDevSecAclDestIpType,
zxDslDevSecAclDestIp,
zxDslDevSecAclDestIpMask,
zxDslDevSecAclDestIpv6PfxLen,
zxDslDevSecAclEtherType,
zxDslDevSecAclVlan
and zxDslDevSecAclPktRateLimit
in zxDslDevSecurityAclTable.
bit 30: value 1 means support pccw DSL_PORT_INFO (Modem Mode).
"
REFERENCE
""
::= { zxDslSysCompatibility 1 }
END
View Git Blame Copy Permalink