WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/supermicro/SUPERMICRO-MI-BGP-MIB

6940 lines
251 KiB
Plaintext
Raw Permalink Blame History

-- Copyright (C) 2008-2014 Super Micro Computer Inc. All Rights Reserved
-- /*****************************************************************
-- * *
-- * $Id: fsmpbgp4.mib,v 1.11 2013/09/02 14:02:34 siva Exp $ *
-- * fsmpbgp4.mib *
-- * *
-- * BGP4 Proprietary MIB. *
-- * *
-- ****************************************************************/
-- MIB FOR BGP-MI
SUPERMICRO-MI-BGP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,NOTIFICATION-TYPE,
IpAddress, Unsigned32, Integer32, enterprises, Gauge32, Counter32 FROM SNMPv2-SMI
DisplayString, RowStatus, DateAndTime, TruthValue FROM SNMPv2-TC
InetAddress, InetAddressType, BgpSafi FROM SUPERMICRO-BGP-MIB;
fsMIBgp MODULE-IDENTITY
LAST-UPDATED "201211280000Z"
ORGANIZATION "Super Micro Computer Inc."
CONTACT-INFO "support@Supermicro.com"
DESCRIPTION
"The Proprietary BGP MIB Created for MI support"
::= { enterprises supermicro-computer-inc(10876) super-switch(101) basic(2) 77 }
-- Scalar object for BGP MI support
fsMIBgp4GlobalTraceDebug OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable global trace for the BGP module.
A four byte integer value is specified for enabling
the level of tracing. Each Bit in the four byte integer variable
represents a level of Trace.
The bits represents the levels as follows:
0 - All Failures,
1 - All Resource Allocation failure,
2 - Init & Shutdown Trace,
3 - Management Trace,
4 - Control Path Trace,
5 - Data Path Trace,
6 - Peer Connection Trace,
7 - Update Message Trace,
8 - FDB Update Trace,
9 - Keep-Alive Trace,
10 - All Transmission Trace,
11 - All Reception Trace,
12 - Dampening Trace,
13 - Events Trace,
14 - High level Packet Dump
15 - Low level packet Dump
16 - Hex Dump
This Traces will be displayed when fsMIBgp4LocalAs is configured for any VR."
::= { fsMIBgp 1 }
fsMIBgp4LocalAs OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This is Global local autonomous system number."
DEFVAL { 0 }
::= { fsMIBgp 2 }
fsMIBgp4MaxPeerEntry OBJECT-TYPE
SYNTAX Integer32 (0..50)
-- MaxPeerEntry (Range should be modified
-- according to the DEFVAL)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Maximum number of peers supported by BGP"
DEFVAL { 50 }
::= { fsMIBgp 3 }
fsMIBgp4MaxNoofRoutes OBJECT-TYPE
SYNTAX Integer32 (0..5000)
-- MaxNoofRoutes (Range should be modified
-- according to the DEFVAL )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"It represents the maximum number of routes in the routing table"
DEFVAL { 5000 }
::= { fsMIBgp 4 }
fsMIBgp4GRAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable or disable GR capability in BGP speaker."
DEFVAL { enable }
::= { fsMIBgp 5 }
fsMIBgp4GRRestartTimeInterval OBJECT-TYPE
SYNTAX Integer32 (1..4096)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This is the estimated time (in seconds) it will take for the BGP
session to be re-established after a restart. Suggested default value
should be less than or equal to Hold Time carried in open message.
The GR restart time interval configured can be used only for the new peers
sessions established and not for the already established peer sessions"
DEFVAL { 90 }
::= { fsMIBgp 6 }
fsMIBgp4RestartExitReason OBJECT-TYPE
SYNTAX INTEGER {
none (1), -- none attempted
inProgress (2), -- restart in progress
completed (3), -- successfully completed
failure (4) -- restart failure.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Describes the outcome of the last attempt at a graceful restart.
If the value is 'none': no restart has yet been attempted.
'inProgress': a restart attempt is currently underway.
'Completed': a restart is completed successfully.
'failure': failure due to the speaker is not completed the
restart process within the restart interval."
::= { fsMIBgp 7 }
fsMIBgp4GRSelectionDeferralTimeInterval OBJECT-TYPE
SYNTAX Integer32 (60..1800)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This interval is the upper bound on the amount of time a router
defers its route selection. The value of this timer should be large
enough, so as to provide all the peers of the Restarting Speaker with
enough time to send all the routes to the Restarting Speaker."
DEFVAL { 60 }
::= { fsMIBgp 8 }
fsMIBgp4GRStaleTimeInterval OBJECT-TYPE
SYNTAX Integer32 (90..3600)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This interval is the upper bound on the amount of time a router retains
the stale routes.
The GR stale time interval configured can be used only for the new peers
sessions established and not for the already established peer sessions"
DEFVAL { 150 }
::= { fsMIBgp 9 }
fsMIBgp4GRMode OBJECT-TYPE
SYNTAX INTEGER {
restarting (1),
receiving (2),
none(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the BGP speaker is restarting speaker
or receiving speaker."
::= { fsMIBgp 10 }
fsMIBgp4RestartSupport OBJECT-TYPE
SYNTAX INTEGER {
none (1),
plannedOnly (2),
plannedAndUnplanned (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The router's support for BGP graceful restart Options include:
no restart support, only planned restarts, or both planned and unplanned
restarts. This object is persistent and when written the entity SHOULD
save the change to non-volatile storage. When BGP GR admin status is
enabled, the restart option can be one of the following: only planned
restarts, or both planned and unplanned restarts."
DEFVAL { none }
::= { fsMIBgp 11 }
fsMIBgp4RestartStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
plannedRestart (2),
unplannedRestart (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current status of BGP graceful restart, it indicates whether the speaker
restarted or not if it is restarted whether it is a planned restart or unplanned restart "
::= { fsMIBgp 12 }
fsMIBgp4ForwardingPreservation OBJECT-TYPE
SYNTAX INTEGER {
preserved (1),
notPreserved (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the forwarding plane is preserved during restart or not"
::= { fsMIBgp 13 }
-- End of scalar object
-- Context table for BGP MI support
fsMIBgpContextTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgpContextEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This context table contains the global parameters of BGP
that is required to be configured for each context."
::= { fsMIBgp 14 }
fsMIBgpContextEntry OBJECT-TYPE
SYNTAX FsMIBgpContextEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An Entry for the configuration in a particular VR."
INDEX { fsMIBgp4ContextId }
::= { fsMIBgpContextTable 1 }
FsMIBgpContextEntry ::= SEQUENCE {
fsMIBgp4ContextId Integer32,
fsMIBgp4GlobalAdminStatus INTEGER,
fsMIBgp4Identifier IpAddress,
fsMIBgp4Synchronization INTEGER,
fsMIBgp4DefaultLocalPref Unsigned32,
fsMIBgp4AdvtNonBgpRt INTEGER,
fsMIBgp4TraceEnable Unsigned32,
fsMIBgp4DebugEnable Unsigned32,
fsMIBgp4OverlappingRoute INTEGER,
fsMIBgp4AlwaysCompareMED INTEGER,
fsMIBgp4DefaultOriginate INTEGER,
fsMIBgp4DefaultIpv4UniCast INTEGER,
fsMIBgp4IsTrapEnabled INTEGER,
fsMIBgp4NextHopProcessingInterval Integer32,
fsMIBgp4IBGPRedistributionStatus INTEGER,
fsMIBgp4RRDAdminStatus INTEGER,
fsMIBgp4RRDProtoMaskForEnable Integer32,
fsMIBgp4RRDSrcProtoMaskForDisable Integer32,
fsMIBgp4RRDDefaultMetric Unsigned32,
fsMIBgp4RRDRouteMapName DisplayString,
fsMIBgp4RRDMatchTypeEnable INTEGER,
fsMIBgp4RRDMatchTypeDisable INTEGER,
fsMIBgp4AscConfedId Unsigned32,
fsMIBgp4AscConfedBestPathCompareMED INTEGER,
fsMIBgp4RflbgpClusterId OCTET STRING,
fsMIBgp4RflRflSupport INTEGER,
fsMIBgp4RfdCutOff Integer32,
fsMIBgp4RfdReuse Integer32,
fsMIBgp4RfdCeiling Integer32,
fsMIBgp4RfdMaxHoldDownTime Integer32,
fsMIBgp4RfdDecayHalfLifeTime Integer32,
fsMIBgp4RfdDecayTimerGranularity Integer32,
fsMIBgp4RfdReuseTimerGranularity Integer32,
fsMIBgp4RfdReuseIndxArraySize Integer32,
fsMIBgp4RfdAdminStatus INTEGER,
fsMIBgp4CommMaxInFTblEntries Integer32,
fsMIBgp4CommMaxOutFTblEntries Integer32,
fsMIBgp4ExtCommMaxInFTblEntries Integer32,
fsMIBgp4ExtCommMaxOutFTblEntries Integer32,
fsMIBgp4CapabilitySupportAvailable TruthValue,
fsMIBgp4MaxCapsPerPeer Integer32,
fsMIBgp4MaxInstancesPerCap Integer32,
fsMIBgp4MaxCapDataSize Integer32,
fsMIBgp4PreferenceValue Integer32,
fsMIBgp4ContextStatus INTEGER,
fsMIBgp4IBGPMaxPaths Integer32,
fsMIBgp4EBGPMaxPaths Integer32,
fsMIBgp4EIBGPMaxPaths Integer32,
fsMIBgp4OperIBGPMaxPaths Integer32,
fsMIBgp4OperEBGPMaxPaths Integer32,
fsMIBgp4OperEIBGPMaxPaths Integer32,
fsMIBgp4FourByteASNSupportStatus INTEGER,
fsMIBgp4FourByteASNotationType INTEGER,
fsMIBgp4LocalAsNo Unsigned32,
fsMIBgp4RIBRoutes Counter32
}
fsMIBgp4ContextId OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index value that uniquely identifies the virtual router in which the configuration is done."
::= { fsMIBgpContextEntry 1 }
fsMIBgp4GlobalAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up (1),
down(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of the BGP system. The BGP4 speaker is
functionally active only when the global admin status is up. The global
admin status can be made up only if the fsMIBgp4LocalAs is configured."
DEFVAL { down }
::= { fsMIBgpContextEntry 2 }
fsMIBgp4Identifier OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the BGP Identifier in that VR. If admin status
is made up, by default the BGP Identifier will take
the value of highest interface address. If the BGP Speaker is
administratively active, then the BGP Identifier can be configured
explicitly. If configured explicitly,then this configured value will be
preserved even across BGP restarts. Inorder to restore the default value
for BGP Identifier configure this object as 0.0.0.0. Peering sessions
will be reset if the BGP Identifer is changed. This object can be set
only if fsMIBgp4LocalAs has been configured."
::= { fsMIBgpContextEntry 3 }
fsMIBgp4Synchronization OBJECT-TYPE
SYNTAX INTEGER {
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Attribute to enable/disable synchronization within an AS.
This object can be set only if fsMIBgp4LocalAs has been configured."
DEFVAL { disable }
::= { fsMIBgpContextEntry 4 }
fsMIBgp4DefaultLocalPref OBJECT-TYPE
SYNTAX Unsigned32 ( 0 .. 2147483647 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default value of local-pref that is to be sent in updates to internal
peers.This object can be set only if fsMIBgp4LocalAs has been configured."
DEFVAL { 100 }
::= { fsMIBgpContextEntry 5 }
fsMIBgp4AdvtNonBgpRt OBJECT-TYPE
SYNTAX INTEGER
{
external(1),
externalAndinternal(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This mib object can be used to configure the peer type to whom
non-bgp routes can be propagated.
external - indicates non-bgp routes can be exported to only
external peers.All types of non-bgp routes
can be propagated to external peers.
externalAndInternal - non-bgp routes can be propagated to both external
and internal peers.
This object can be set only if fsMIBgp4LocalAs has been configured."
DEFVAL { externalAndinternal }
::= { fsMIBgpContextEntry 6 }
fsMIBgp4TraceEnable OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object can be used to enable trace dynamically in BGP
module. A four byte integer value is specified for enabling
the level of tracing.Each Bit in the four byte integer variable
represents a level of Trace.
The bits represents the levels as follows:
0 - All Failures,
1 - All Resource Allocation failure,
2 - Init & Shutdown Trace,
3 - Management Trace,
4 - Control Path Trace,
5 - Data Path Trace,
6 - Peer Connection Trace,
7 - Update Message Trace,
8 - FDB Update Trace,
9 - Keep-Alive Trace,
10 - All Transmission Trace,
11 - All Reception Trace,
12 - Dampening Trace,
13 - Events Trace,
14 - High level Packet Dump
15 - Low level packet Dump
16 - Hex Dump
The remaining bits are unused.
The combination of levels are also allowed. For example if the bits 1
and 2 are set, then the Trace statements related to management and Data
Path will be printed.
The user have to enter the corresponding integer value for the bits set.
For example if bits 1 and 2 are set then value of 6 should be entered.
This object can be set only if fsMIBgp4LocalAs has been configured."
::= { fsMIBgpContextEntry 7 }
fsMIBgp4DebugEnable OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object can be used to enable debug dynamically in BGP module.
Its a four byte integer value specified for enabling the level
of debugging. Each Bit in the four byte integer variable
represents a level of debug. The combination of levels are also
allowed. This object can be set only if fsMIBgp4LocalAs is configured."
::= { fsMIBgpContextEntry 8 }
fsMIBgp4OverlappingRoute OBJECT-TYPE
SYNTAX INTEGER
{
moreSpecific(1),
lessSpecific(2),
both(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the BGP speaker's policy for handling
the overlapping routes. When an overlapping route is received, depending
upon the configured policy either the less-specific routes or
more-specific routes or both routes are installed in the RIB tree. This
object can be set only if fsMIBgp4LocalAs has been configured and
fsMIBgp4GlobalAdminStatus is down."
DEFVAL { both }
::= { fsMIBgpContextEntry 9 }
fsMIBgp4AlwaysCompareMED OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to disable, then in best route decision process,
MED will be compared only between routes received from the same
autonomous system. If set to enable, irrespective of the autonomous
system from which the routes are received, MED comparision will be done.
This object can be set only if the fsMIBgp4LocalAs is set."
DEFVAL { disable }
::= { fsMIBgpContextEntry 10 }
fsMIBgp4DefaultOriginate OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to enable/disable the redistribution and
advertisement of the default route (0.0.0.0/0). By default, the
default routes are not redistributed into BGP. Only if this object
is set as enable, the default route gets redistributed and advertised
to BGP Peers. If the default route is neither present in IP FDB nor
received from any Peer, enabling this object will not result in
advertisement of default route. This object can be set only if the
fsMIBgp4LocalAs is set."
DEFVAL { disable }
::= { fsMIBgpContextEntry 11 }
fsMIBgp4DefaultIpv4UniCast OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to enable, and if a neighbor is created, then
the MP IPv4 Unicast Address Family Capability will be negotiate for
that peer. If this object is set as disable and if a neighbor is
created, then IPv4 unicast capability will not be negotiated for that
neighbor, unless IPv4 unicast capability is explicitly configured for
that neighbor. Changing the status of this object will not cause
any change in the MP IPV4 Unicast negotiation status of the already
existing peer. This object can be set only if fsMIBgp4LocalAs is
configured."
DEFVAL { enable }
::= { fsMIBgpContextEntry 12 }
fsMIBgp4IsTrapEnabled OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to disable, then the NOTIFICATION messages wont be sent to
the SNMP Manager. If enabled, NOTIFICATION messages are sent."
DEFVAL { enable }
::= { fsMIBgpContextEntry 13 }
fsMIBgp4NextHopProcessingInterval OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the interval at which next hops will be mointored for reachablity"
DEFVAL { 60 }
::= { fsMIBgpContextEntry 14 }
fsMIBgp4IBGPRedistributionStatus OBJECT-TYPE
SYNTAX INTEGER
{
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to enable, IBGP routes will also be redistributed to other
IGP protocols when redistribution is enabled for that protocol"
DEFVAL { disable }
::= { fsMIBgpContextEntry 15 }
fsMIBgp4RRDAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
disable(0),
enable(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls redistribution of Direct, Static, IGP(OSPF,RIP) routes into
BGP. If this object is set to enable, then routes from protocols as
specified by fsMIBgp4RRDProtoMaskForEnable will be imported into BGP and
the BGP learnt routes will be distributed to IGP. If this object is set
as disable, then the routes learned from protocols specified by
fsMIBgp4RRDProtoMaskForEnable will be removed from BGP and no route will
be either distributed to or imported from IGP. This object can
be set only if fsbgp4GlobalAdminStatus is up. When the global admin
state changes the fsMIBgp4RRDAdminStatus also changes."
DEFVAL { enable }
::= { fsMIBgpContextEntry 16 }
fsMIBgp4RRDProtoMaskForEnable OBJECT-TYPE
SYNTAX Integer32
-- See the description
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The bit mask of source protocols from which routes are
imported to BGP.(LSB corresponds to Bit 0)
Bit 1, if set, indicates that direct routes can be
redistributed into BGP. (value = 2)
Bit 2, if set, indicates that static routes can be
redistributed into BGP. (value = 4)
Bit 7, if set, indicates that routes from RIP can be
redistributed into BGP. (value = 128)
Bit 12, if set, indicates that OSPF routes can be
redistributed into BGP. (value = 4096)
Other bits are reserved for future use."
::= { fsMIBgpContextEntry 17 }
fsMIBgp4RRDSrcProtoMaskForDisable OBJECT-TYPE
SYNTAX Integer32
-- See the description
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The bit mask of source protocols from which redistribution
to BGP is disabled.(LSB corresponds to Bit 0)
Bit 1, if set, indicates that direct routes cannot be
redistributed into BGP. (value = 2)
Bit 2, if set, indicates that static routes cannot be
redistributed into BGP. (value = 4)
Bit 7, if set, indicates that routes from RIP cannot be
redistributed into BGP. (value = 128)
Bit 12, if set, indicates that OSPF routes cannot be
redistributed into BGP. (value = 4096)
Other bits are reserved for future use."
::= { fsMIBgpContextEntry 18 }
fsMIBgp4RRDDefaultMetric OBJECT-TYPE
SYNTAX Unsigned32 ( 0 .. 2147483647 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default metric value for the IGP routes and static route. If
configured to 0, the metric received from the IGP route will be used.
If configured to other value, the MED value of the redistributed routes
take this value. This value have no effect on the Direct routes."
DEFVAL { 0 }
::= { fsMIBgpContextEntry 19 }
fsMIBgp4RRDRouteMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..20))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Name Identifies the specified route-map
in the list of route-maps. If this Object needs to be
changed, first reset this object and then configure the
new value."
::= { fsMIBgpContextEntry 20 }
fsMIBgp4RRDMatchTypeEnable OBJECT-TYPE
SYNTAX INTEGER
{
external(1),
internal(2),
nssaExternal(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Match type Enable specifies the OSPF route type that
needs to be redistributed into BGP, This object is
used only ospf redistribution."
::= { fsMIBgpContextEntry 21 }
fsMIBgp4RRDMatchTypeDisable OBJECT-TYPE
SYNTAX INTEGER
{
external(1),
internal(2),
nssaExternal(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Match type Disable specifies the OSPF route type
that should be disbled from redistribution into BGP.
This object is used only for OSPF protocol."
::= { fsMIBgpContextEntry 22 }
fsMIBgp4AscConfedId OBJECT-TYPE
SYNTAX Unsigned32 (0 .. 4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Local Confederation Identification number of
the AS confederation, a value of zero indicates the
absence of this value. The object fsbgp4LocalAs must be
configured prior to configuring this object.
If already set (to non-zero value), this value must be
reset to zero (represets absence of confed) before
reconfiguring confed id."
DEFVAL {0}
::= { fsMIBgpContextEntry 23}
fsMIBgp4AscConfedBestPathCompareMED OBJECT-TYPE
SYNTAX INTEGER
{
set(1),
clear(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to compare MED among paths learned
from confed peers. if this object value is set and AS path
contains only AS_CONFED segments then then MED should be
compared if this object value is clear and sanitized path
has different left-most entry in AS path then MED should not
be compared"
DEFVAL {clear}
::= { fsMIBgpContextEntry 24 }
fsMIBgp4RflbgpClusterId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The configured Cluster-ID of the local router. By default, when the BGP
speaker acts as Route Reflector, the BGP Identifier is used as the
cluster id. Administrator can overwrite the default cluster-id by
configuring this object. This object can be configured only if
fsMIBgp4LocalAS is configured."
REFERENCE
"RFC 2796 - BGP Route Reflection"
::= { fsMIBgpContextEntry 25 }
fsMIBgp4RflRflSupport OBJECT-TYPE
SYNTAX INTEGER {
none (1),
clientsupport (2),
noClientSupport (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired support of the Route Reflector in the cluster.
Note that none(1) value is for read-only. This object can be set only if
fsMIBgp4LocalAS is configured."
DEFVAL {2}
::= { fsMIBgpContextEntry 26 }
fsMIBgp4RfdCutOff OBJECT-TYPE
SYNTAX Integer32 (2000..3999)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The figure-of-merit value above which the route will be suppressed.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
is set to down and fsMIBgp4LocalAS is configured."
DEFVAL { 2000 }
::= {fsMIBgpContextEntry 27 }
fsMIBgp4RfdReuse OBJECT-TYPE
SYNTAX Integer32 (100..1999)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The figure-of-merit value below which the suppressed route will be reused.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured."
DEFVAL { 750 }
::= {fsMIBgpContextEntry 28 }
fsMIBgp4RfdCeiling OBJECT-TYPE
SYNTAX Integer32 (4000..10000)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest value the figure-of-merit can attain."
DEFVAL { 8000 }
::= {fsMIBgpContextEntry 29 }
fsMIBgp4RfdMaxHoldDownTime OBJECT-TYPE
SYNTAX Integer32 (1800..10800)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum time (in seconds) a route can be suppressed.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured."
DEFVAL { 3600 }
::= {fsMIBgpContextEntry 30 }
fsMIBgp4RfdDecayHalfLifeTime OBJECT-TYPE
SYNTAX Integer32 (600..2700)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The time duration in seconds during which the figure-of-merit will be
reduced by half. This object can be set only if fsMIBgp4RfdAdminStatus is
disabled and fsMIBgp4LocalAS is configured."
DEFVAL { 900 }
::= { fsMIBgpContextEntry 31 }
fsMIBgp4RfdDecayTimerGranularity OBJECT-TYPE
SYNTAX Integer32 (1..10800)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time granularity in seconds used to perform all decay calculations.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured."
DEFVAL { 1 }
::= {fsMIBgpContextEntry 32 }
fsMIBgp4RfdReuseTimerGranularity OBJECT-TYPE
SYNTAX Integer32 (15..10800)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval between evaluations of the reuse lists.
This object can be set only if fsMIBgp4RfdAdminStatus is disabled
and fsMIBgp4LocalAS is configured."
DEFVAL { 15 }
::= {fsMIBgpContextEntry 33 }
fsMIBgp4RfdReuseIndxArraySize OBJECT-TYPE
SYNTAX Integer32 (256..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Size of reuse index arrays.This object can be set only if
fsMIBgp4GlobalAdminStatus is set to down and fsMIBgp4LocalAS is
configured."
DEFVAL { 1024 }
::= {fsMIBgpContextEntry 34 }
fsMIBgp4RfdAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of the RouteFlap Dampening feature of the BGP system.
The SupermicroBGP4 speaker's route flap dampending is functionally active only
when the RFD admin status is enabled. The RFD admin status can be enabled
only if the fsMIBgp4GlobalAdminStatus is set to up. When
fsMIBgp4GlobalAdminStatus is set to down, RFD admin status will also be
disabled. On disabling RFD admin status, the route dampening history
and peer dampening history will be cleared and the dampened routes will
be advertised as feasible routes. By default after the
fsMIBgp4GlobalAdminStatus is set to up, the RFD admin status will be made up."
DEFVAL { enable }
::= {fsMIBgpContextEntry 35 }
fsMIBgp4CommMaxInFTblEntries OBJECT-TYPE
SYNTAX Integer32 (1..50000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Number of Entries in the Input Community Filter Table.
This object can not be set to a higher value than the initial value of the
object.However initial value can be changed in inc/system.size file"
DEFVAL { 10000 }
::= {fsMIBgpContextEntry 36 }
fsMIBgp4CommMaxOutFTblEntries OBJECT-TYPE
SYNTAX Integer32 (1..50000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of entries in the outgoing community filter table.
This object can not be set to a higher value than the initial value of the
object.However initial value can be changed in inc/system.size file"
DEFVAL { 10000 }
::= {fsMIBgpContextEntry 37 }
fsMIBgp4ExtCommMaxInFTblEntries OBJECT-TYPE
SYNTAX Integer32 (1..10000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum Number of Entries in the Input Extended Community Filter Table.
This object can not be set to a higher value than the initial value of the
object.However initial value can be changed in inc/system.size file"
DEFVAL { 2000 }
::= {fsMIBgpContextEntry 38 }
fsMIBgp4ExtCommMaxOutFTblEntries OBJECT-TYPE
SYNTAX Integer32 (1..10000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of entries in the outgoing extended community filter table.
This object can not be set to a higher value than the initial value of the
object.However initial value can be changed in inc/system.size file"
DEFVAL { 2000 }
::= {fsMIBgpContextEntry 39 }
fsMIBgp4CapabilitySupportAvailable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable determines whether the Capability Advertisement
Support is enabled or not.This object can be set only if
fsMIBgp4GlobalAdminStatus is set to down and fsMIBgp4LocalAS is configured."
DEFVAL { true }
::= {fsMIBgpContextEntry 40 }
fsMIBgp4MaxCapsPerPeer OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of Capabilities that can be supported per peer
or received from peer.
This object can not be set to a higher value than the initial value of the
object.However initial value can be changed in inc/system.size file"
DEFVAL { 10 }
::= { fsMIBgpContextEntry 41 }
fsMIBgp4MaxInstancesPerCap OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of Instances of same Capability code can be advertised
to peer or received from peer.
This object can not be set to a higher value than the initial value of the
object.However initial value can be changed in inc/system.size file"
DEFVAL { 5 }
::= { fsMIBgpContextEntry 42 }
fsMIBgp4MaxCapDataSize OBJECT-TYPE
SYNTAX Integer32 (4..252)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum size of the Capability Data size of each Capability.
To enable packing, the size should be multiples of 4.
This object can not be set to a higher value than the initial value of the
object.However initial value can be changed in inc/system.size file"
DEFVAL { 16 }
::= { fsMIBgpContextEntry 43 }
fsMIBgp4PreferenceValue OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Preference value for RIP routes. Use '0' to set default value"
DEFVAL { 122 }
::= { fsMIBgpContextEntry 44 }
fsMIBgp4ContextStatus OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"this is used to enable or disable status of context"
::= { fsMIBgpContextEntry 45 }
fsMIBgp4IBGPMaxPaths OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of internal BGP multipath routes to be added per destination network in Routing table.
When this object takes the value 1, then only best route is added to Forwarding table.
This configuration will have effect only after hard/soft reset."
DEFVAL { 1 }
::= { fsMIBgpContextEntry 46 }
fsMIBgp4EBGPMaxPaths OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of external BGP multipath routes to be added per destination network in Routing table.
When this object takes the value 1, then only best route is added to Forwarding table.
This configuration will have effect only after hard/soft reset."
DEFVAL { 1 }
::= { fsMIBgpContextEntry 47 }
fsMIBgp4EIBGPMaxPaths OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of external plus internal BGP multipath routes (with same AS PATH) to be
added per destination network in Routing table.
When this object takes the value 1, then only best route is added to Forwarding table.
This configuration will have effect only after hard/soft reset."
DEFVAL { 1 }
::= { fsMIBgpContextEntry 48 }
fsMIBgp4OperIBGPMaxPaths OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Operational value for Maximum number of internal BGP multipath routes to be added per
destination network in Routing table.
When this object takes the value 1, then only best route is added to Forwarding table."
DEFVAL { 1 }
::= { fsMIBgpContextEntry 49}
fsMIBgp4OperEBGPMaxPaths OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Operational value for Maximum number of external BGP multipath routes that to be added
per destination network in Routing table.
When this object takes the value 1, then only best route is added to Forwarding table."
DEFVAL { 1 }
::= { fsMIBgpContextEntry 50 }
fsMIBgp4OperEIBGPMaxPaths OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Operational value for Maximum number of external plus internal BGP multipath routes
(with same AS PATH) to be added in Routing table.
When this object takes the value 1, then only best route is added to Forwarding table."
DEFVAL { 1 }
::= { fsMIBgpContextEntry 51 }
fsMIBgp4FourByteASNSupportStatus OBJECT-TYPE
SYNTAX INTEGER {
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable or disable 4 byte ASN support in BGP Speaker.
This can be configured only if fsMIBgp4GlobalAdminStatus is down."
DEFVAL { enable }
::= { fsMIBgpContextEntry 52 }
fsMIBgp4FourByteASNotationType OBJECT-TYPE
SYNTAX INTEGER {
asplain (1),
asdot (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object denotes the notation to be used to display the 4 byte ASN. This
will change only the way the AS number is represented within router show
commands in the Command Line Interface (CLI) framework. This object can be
configured only if fsbgp4FourByteASNSupportStatus is enabled"
DEFVAL { asplain }
::= { fsMIBgpContextEntry 53 }
fsMIBgp4LocalAsNo OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This is local autonomous system number specific to a Context."
DEFVAL { 0 }
::= { fsMIBgpContextEntry 54 }
fsMIBgp4RIBRoutes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the total number of the routes present in the RIB of a context at the given instance."
::= { fsMIBgpContextEntry 55 }
-- End of Context Table
-- RRDMetric Table
fsMIBgp4RRDMetricTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4RRDMetricEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table describing the configuration of metric values to
the redistributed routes."
::= { fsMIBgp 15 }
fsMIBgp4RRDMetricEntry OBJECT-TYPE
SYNTAX FsMIBgp4RRDMetricEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the configuration of single entry."
INDEX {fsMIBgp4ContextId,
fsMIBgp4RRDMetricProtocolId}
::= { fsMIBgp4RRDMetricTable 1 }
FsMIBgp4RRDMetricEntry ::= SEQUENCE {
fsMIBgp4RRDMetricProtocolId INTEGER,
fsMIBgp4RRDMetricValue Integer32
}
fsMIBgp4RRDMetricProtocolId OBJECT-TYPE
SYNTAX INTEGER
{
ospf(1),
rip(2),
connected(3),
static(4)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Protocol Id for which the Metric value needs to be changed by the User."
::= { fsMIBgp4RRDMetricEntry 1 }
fsMIBgp4RRDMetricValue OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Metric value to be considered instead of the default value from RTM
for the protocol specified. If the value not secified by the user,
default metric value is considered."
::= { fsMIBgp4RRDMetricEntry 2 }
-- End of RRDMetric Table
-- Incoming Filter Table
-- Represents the incoming filter status (can be either accept/deny)
-- for a given community value
fsMIBgpComm OBJECT IDENTIFIER ::= { fsMIBgp 16 }
fsMIBgp4CommInFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4CommInFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure the incoming filter status
for a given community value"
::= {fsMIBgpComm 1 }
fsMIBgp4CommInFilterEntry OBJECT-TYPE
SYNTAX FsMIBgp4CommInFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Incoming Communities Filter Table Entry"
INDEX { fsMIBgp4ContextId,
fsMIBgp4InFilterCommVal
}
::= { fsMIBgp4CommInFilterTable 1 }
FsMIBgp4CommInFilterEntry ::= SEQUENCE {
fsMIBgp4InFilterCommVal
Unsigned32,
fsMIBgp4CommIncomingFilterStatus
INTEGER,
fsMIBgp4InFilterRowStatus
RowStatus
}
fsMIBgp4InFilterCommVal OBJECT-TYPE
SYNTAX Unsigned32 (65536..4294901759|4294967041..4294967043)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The community value for which the input filtering
policy is to be updated"
::= { fsMIBgp4CommInFilterEntry 1 }
fsMIBgp4CommIncomingFilterStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
accept (2),
deny (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Incoming filtering policy for the community.
o none - is for read-only
o accept - Accept the community value.
o deny - Deny the community value."
DEFVAL { 2 }
::= { fsMIBgp4CommInFilterEntry 2 }
fsMIBgp4InFilterRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status for creating entries into this table.This object can be set
only if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4CommInFilterEntry 3 }
--- Outgoing Filter Table
--- Represents the outgoing filter status (can be either adevertise/filter)
--- for a given community value
fsMIBgp4CommOutFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4CommOutFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure the outgoing filter status
for a given community value"
::= {fsMIBgpComm 2 }
fsMIBgp4CommOutFilterEntry OBJECT-TYPE
SYNTAX FsMIBgp4CommOutFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Outgoing Communities Filter Table Entry"
INDEX { fsMIBgp4ContextId,
fsMIBgp4OutFilterCommVal
}
::= { fsMIBgp4CommOutFilterTable 1 }
FsMIBgp4CommOutFilterEntry ::= SEQUENCE {
fsMIBgp4OutFilterCommVal
Unsigned32,
fsMIBgp4CommOutgoingFilterStatus
INTEGER,
fsMIBgp4OutFilterRowStatus
RowStatus
}
fsMIBgp4OutFilterCommVal OBJECT-TYPE
SYNTAX Unsigned32 (65536..4294901759|4294967041..4294967043)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The community value for which the outgoing filtering
policy is to be updated"
::= { fsMIBgp4CommOutFilterEntry 1 }
fsMIBgp4CommOutgoingFilterStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
advertise (2),
filter (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Outgoing filtering policy for the community.
o none - is for read-only
o advertise - Advertise the community value.
o filter - Filter the community value."
DEFVAL { 2 }
::= { fsMIBgp4CommOutFilterEntry 2 }
fsMIBgp4OutFilterRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status for creating entries into this table.This object can be set
only if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4CommOutFilterEntry 3 }
--- Incoming Extended Community Filter Table
--- Represents the incoming filter status (can be either accept/deny)
--- for a given extended community value
fsMIBgpExtComm OBJECT IDENTIFIER ::= { fsMIBgp 17 }
fsMIBgp4ExtCommInFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4ExtCommInFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure the incoming filter status
for a given extended community value"
::= {fsMIBgpExtComm 1}
fsMIBgp4ExtCommInFilterEntry OBJECT-TYPE
SYNTAX FsMIBgp4ExtCommInFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Incoming Extended Communities Filter Table Entry"
INDEX { fsMIBgp4ContextId,
fsMIBgp4ExtCommInFilterCommVal
}
::= { fsMIBgp4ExtCommInFilterTable 1 }
FsMIBgp4ExtCommInFilterEntry ::= SEQUENCE {
fsMIBgp4ExtCommInFilterCommVal
OCTET STRING,
fsMIBgp4ExtCommIncomingFilterStatus
INTEGER,
fsMIBgp4ExtCommInFilterRowStatus
RowStatus
}
fsMIBgp4ExtCommInFilterCommVal OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The extended community value for which the input filtering
policy is to be updated"
::= { fsMIBgp4ExtCommInFilterEntry 1 }
fsMIBgp4ExtCommIncomingFilterStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
accept (2),
deny (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Incoming filtering policy for the extended community.
o none - is for read-only
o accept - Accept the extended community value.
o deny - Deny the extended community value."
DEFVAL { 2 }
::= { fsMIBgp4ExtCommInFilterEntry 2 }
fsMIBgp4ExtCommInFilterRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row Status for creating the entries into this table.This object can be set
only if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4ExtCommInFilterEntry 3 }
--- Outgoing Extended Community Filter Table
--- Represents the outgoing filter status (can be either adevertise/filter)
--- for a given extended community value
fsMIBgp4ExtCommOutFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4ExtCommOutFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure the outgoing filter status
for a given extended community value"
::= {fsMIBgpExtComm 2}
fsMIBgp4ExtCommOutFilterEntry OBJECT-TYPE
SYNTAX FsMIBgp4ExtCommOutFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Outgoing Extended Communities Filter Table Entry"
INDEX { fsMIBgp4ContextId,
fsMIBgp4ExtCommOutFilterCommVal
}
::= { fsMIBgp4ExtCommOutFilterTable 1 }
FsMIBgp4ExtCommOutFilterEntry ::= SEQUENCE {
fsMIBgp4ExtCommOutFilterCommVal
OCTET STRING,
fsMIBgp4ExtCommOutgoingFilterStatus
INTEGER,
fsMIBgp4ExtCommOutFilterRowStatus
RowStatus
}
fsMIBgp4ExtCommOutFilterCommVal OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The extended community value for which the outgoing filtering
policy is to be updated"
::= { fsMIBgp4ExtCommOutFilterEntry 1 }
fsMIBgp4ExtCommOutgoingFilterStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
advertise (2),
noadvertise (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Outgoing filtering policy for the extended community.
o none - is for read-only
o advertise - Advertise the extended community value.
o filter - Filter the extended community value."
::= { fsMIBgp4ExtCommOutFilterEntry 2 }
fsMIBgp4ExtCommOutFilterRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row Status to create entries into this table.This object can be set
only if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4ExtCommOutFilterEntry 3 }
fsMIBgp4TCPMD5Auth OBJECT IDENTIFIER ::= { fsMIBgp 18 }
-- TCP MD5 Authentication Table
fsMIBgp4TCPMD5AuthTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4TCPMD5AuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"TCP MD5 Authientication Table"
::= { fsMIBgp4TCPMD5Auth 1 }
fsMIBgp4TCPMD5AuthEntry OBJECT-TYPE
SYNTAX FsMIBgp4TCPMD5AuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry corresponds to the TCP MD5 authentication password."
INDEX { fsMIBgp4ContextId,
fsMIBgp4TCPMD5AuthPeerType,
fsMIBgp4TCPMD5AuthPeerAddr
}
::= { fsMIBgp4TCPMD5AuthTable 1 }
FsMIBgp4TCPMD5AuthEntry ::= SEQUENCE {
fsMIBgp4TCPMD5AuthPeerType
InetAddressType,
fsMIBgp4TCPMD5AuthPeerAddr
OCTET STRING,
fsMIBgp4TCPMD5AuthPassword
OCTET STRING,
fsMIBgp4TCPMD5AuthPwdSet
INTEGER
}
fsMIBgp4TCPMD5AuthPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address Family Identifier of the peer remote address."
::= { fsMIBgp4TCPMD5AuthEntry 1 }
fsMIBgp4TCPMD5AuthPeerAddr OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1 .. 16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the peer for which the TCP MD5 Authentication
Password has to be set.
to be read."
::= { fsMIBgp4TCPMD5AuthEntry 2 }
fsMIBgp4TCPMD5AuthPassword OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..80))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The TCP MD5 Authentication Password that has to be sent with all TCP
packets originated from the peer."
::= { fsMIBgp4TCPMD5AuthEntry 3 }
fsMIBgp4TCPMD5AuthPwdSet OBJECT-TYPE
SYNTAX INTEGER
{
set (1),
clear (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" This object indicates whether TCP MD5 password needs to be set/reset
for the peer. This object needs to be set before the object
fsMIBgp4TCPMD5AuthPassword can be set."
DEFVAL { clear }
::= { fsMIBgp4TCPMD5AuthEntry 4 }
-- End of TCP MD5 Auth Table
-- AsConfed Table
fsMIBgpAsc OBJECT IDENTIFIER ::= { fsMIBgp 19 }
fsMIBgpAscConfedPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgpAscConfedPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP peer confederation table, this table contains information
about the Member-ASs of the confederation"
::= { fsMIBgpAsc 1 }
fsMIBgpAscConfedPeerEntry OBJECT-TYPE
SYNTAX FsMIBgpAscConfedPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about a member-AS of the confederation."
INDEX { fsMIBgp4ContextId,
fsMIBgpAscConfedPeerASNo
}
::= { fsMIBgpAscConfedPeerTable 1 }
FsMIBgpAscConfedPeerEntry ::= SEQUENCE {
fsMIBgpAscConfedPeerASNo
Unsigned32,
fsMIBgpAscConfedPeerStatus
INTEGER
}
fsMIBgpAscConfedPeerASNo OBJECT-TYPE
SYNTAX Unsigned32 (1 .. 4294967295 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local AS number of member-AS,
a value of zero indicates the absence of this value "
::= { fsMIBgpAscConfedPeerEntry 1 }
fsMIBgpAscConfedPeerStatus OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable or disable the member-AS.
Use disable, if member-AS entry needs to disabled,
Use enable, if member-AS entry needs to be enabled."
::= { fsMIBgpAscConfedPeerEntry 2 }
-- End of ASConfed Table
-- Extensions to the fsMIBgp4 mib
-- Peer Table
fsMIBgp4MpeBgpPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeBgpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP peer table. This table contains, one entry per BGP peer,
information about the connections with BGP peers."
::= { fsMIBgp 20 }
fsMIBgp4MpeBgpPeerEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeBgpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about the connection with a BGP peer."
INDEX {
fsMIBgp4ContextId,
fsMIBgp4mpebgpPeerRemoteAddrType,
fsMIBgp4mpebgpPeerRemoteAddr
}
::= { fsMIBgp4MpeBgpPeerTable 1 }
FsMIBgp4MpeBgpPeerEntry ::= SEQUENCE {
fsMIBgp4mpebgpPeerIdentifier
InetAddress,
fsMIBgp4mpebgpPeerRemoteAddrType
InetAddressType,
fsMIBgp4mpebgpPeerLocalAs
Unsigned32,
fsMIBgp4mpebgpPeerState
INTEGER,
fsMIBgp4mpebgpPeerAdminStatus
INTEGER,
fsMIBgp4mpebgpPeerNegotiatedVersion
Integer32,
fsMIBgp4mpebgpPeerLocalAddr
InetAddress,
fsMIBgp4mpebgpPeerLocalPort
Integer32,
fsMIBgp4mpebgpPeerRemoteAddr
InetAddress,
fsMIBgp4mpebgpPeerRemotePort
Integer32,
fsMIBgp4mpebgpPeerRemoteAs
Unsigned32,
fsMIBgp4mpebgpPeerInUpdates
Counter32,
fsMIBgp4mpebgpPeerOutUpdates
Counter32,
fsMIBgp4mpebgpPeerInTotalMessages
Counter32,
fsMIBgp4mpebgpPeerOutTotalMessages
Counter32,
fsMIBgp4mpebgpPeerLastError
OCTET STRING,
fsMIBgp4mpebgpPeerFsmEstablishedTransitions
Counter32,
fsMIBgp4mpebgpPeerFsmEstablishedTime
Gauge32,
fsMIBgp4mpebgpPeerConnectRetryInterval
Integer32,
fsMIBgp4mpebgpPeerHoldTime
Integer32,
fsMIBgp4mpebgpPeerKeepAlive
Integer32,
fsMIBgp4mpebgpPeerHoldTimeConfigured
Integer32,
fsMIBgp4mpebgpPeerKeepAliveConfigured
Integer32,
fsMIBgp4mpebgpPeerMinASOriginationInterval
Integer32,
fsMIBgp4mpebgpPeerMinRouteAdvertisementInterval
Integer32,
fsMIBgp4mpebgpPeerInUpdateElapsedTime
Gauge32,
fsMIBgp4mpebgpPeerEndOfRIBMarkerSentStatus
INTEGER,
fsMIBgp4mpebgpPeerEndOfRIBMarkerReceivedStatus
INTEGER,
fsMIBgp4mpebgpPeerRestartMode
INTEGER,
fsMIBgp4mpePeerRestartTimeInterval
Integer32,
fsMIBgp4mpePeerAllowAutomaticStart
INTEGER,
fsMIBgp4mpePeerAllowAutomaticStop
INTEGER,
fsMIBgp4mpebgpPeerIdleHoldTimeConfigured
Integer32,
fsMIBgp4mpeDampPeerOscillations
INTEGER,
fsMIBgp4mpePeerDelayOpen
INTEGER,
fsMIBgp4mpebgpPeerDelayOpenTimeConfigured
Integer32,
fsMIBgp4mpePeerPrefixUpperLimit
Integer32,
fsMIBgp4mpePeerTcpConnectRetryCnt
Integer32,
fsMIBgp4mpePeerTcpCurrentConnectRetryCnt
Integer32,
fsMIBgp4mpeIsPeerDamped
INTEGER,
fsMIBgp4mpePeerSessionAuthStatus
INTEGER,
fsMIBgp4mpePeerTCPAOKeyIdInUse
Integer32,
fsMIBgp4mpePeerTCPAOAuthNoMKTDiscard
INTEGER,
fsMIBgp4mpePeerTCPAOAuthICMPAccept
INTEGER,
fsMIBgp4mpePeerIpPrefixNameIn
DisplayString,
fsMIBgp4mpePeerIpPrefixNameOut
DisplayString
}
fsMIBgp4mpebgpPeerIdentifier OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The BGP Identifier of this entry's BGP peer."
::= { fsMIBgp4MpeBgpPeerEntry 1 }
fsMIBgp4mpebgpPeerRemoteAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Type of the remote peer"
::= { fsMIBgp4MpeBgpPeerEntry 2 }
fsMIBgp4mpebgpPeerLocalAs OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"It is used to configure as Local As per peer "
::= { fsMIBgp4MpeBgpPeerEntry 3 }
fsMIBgp4mpebgpPeerState OBJECT-TYPE
SYNTAX INTEGER {
idle(1),
connect(2),
active(3),
opensent(4),
openconfirm(5),
established(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The BGP peer connection state."
::= { fsMIBgp4MpeBgpPeerEntry 4 }
fsMIBgp4mpebgpPeerAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
stop(1),
start(2),
autostart(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of the BGP connection. A transition from
'stop' to 'start' will cause the BGP Start Event to be generated.
A transition from 'start' to 'stop' will cause the BGP Stop
Event to be generated. This parameter can be used to restart BGP
peer connections. Whenever the 'fsMIBgp4mpePeerAllowAutomaticStart' is
enabled, 'fsMIBgp4mpebgpPeerAdminStatus' will take the value 'auto-start'.
The peer waits till the IdleHold Timer expires, and then it will
proceed to generate the BGP Start Event. 'fsMIBgp4mpebgpPeerAdminStatus'
takes the value 'stop' under two circumstances:
1) Whenever the administrator manually triggers BGP Stop Event.
2) Whenever the 'fsMIBgp4mpePeerAllowAutomaticStop' is enabled and also if
the IdleHold Timer exceeds its Maximum Threshold value, then BGP Stop
Event is issued automatically, without the manual intervention of the
administrator.
Care should be used in providing write access
to this object without adequate authentication."
::= { fsMIBgp4MpeBgpPeerEntry 5 }
fsMIBgp4mpebgpPeerNegotiatedVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The negotiated version of BGP running between the two peers."
::= { fsMIBgp4MpeBgpPeerEntry 6 }
fsMIBgp4mpebgpPeerLocalAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local IP address of this entry's BGP connection."
::= { fsMIBgp4MpeBgpPeerEntry 7 }
fsMIBgp4mpebgpPeerLocalPort OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local port for the TCP connection between the BGP peers."
::= { fsMIBgp4MpeBgpPeerEntry 8 }
fsMIBgp4mpebgpPeerRemoteAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote IP address of this entry's BGP peer."
::= { fsMIBgp4MpeBgpPeerEntry 9 }
fsMIBgp4mpebgpPeerRemotePort OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote port for the TCP connection between the BGP peers.
Note that the objects bgpPeerLocalAddr, bgpPeerLocalPort,
bgpPeerRemoteAddr and bgpPeerRemotePort provide the appropriate
reference to the standard MIB TCP connection table."
::= { fsMIBgp4MpeBgpPeerEntry 10 }
fsMIBgp4mpebgpPeerRemoteAs OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote autonomous system number."
::= { fsMIBgp4MpeBgpPeerEntry 11 }
fsMIBgp4mpebgpPeerInUpdates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BGP UPDATE messages received on this connection.
This object should be initialized to zero (0) when the connection
is established."
::= { fsMIBgp4MpeBgpPeerEntry 12 }
fsMIBgp4mpebgpPeerOutUpdates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BGP UPDATE messages transmitted on this connection.
This object should be initialized to zero (0) when the connection
is established."
::= { fsMIBgp4MpeBgpPeerEntry 13 }
fsMIBgp4mpebgpPeerInTotalMessages OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of messages received from the remote peer on this
connection. This object should be initialized to zero when the
connection is established."
::= { fsMIBgp4MpeBgpPeerEntry 14 }
fsMIBgp4mpebgpPeerOutTotalMessages OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of messages transmitted to the remote peer on
this connection. This object should be initialized to zero when
the connection is established."
::= { fsMIBgp4MpeBgpPeerEntry 15 }
fsMIBgp4mpebgpPeerLastError OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last error code and subcode seen by this peer on this connection.
If no error has occurred, this field is zero. Otherwise, the first
byte of this two byte OCTET STRING contains the error code, and the
second byte contains the subcode."
::= { fsMIBgp4MpeBgpPeerEntry 16 }
fsMIBgp4mpebgpPeerFsmEstablishedTransitions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of times the BGP FSM transitioned into the
established state."
::= { fsMIBgp4MpeBgpPeerEntry 17 }
fsMIBgp4mpebgpPeerFsmEstablishedTime OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This timer indicates how long (in seconds) this peer has been in the
Established state or how long since this peer was last in the
Established state. It is set to zero when a new peer is configured
or the router is booted."
::= { fsMIBgp4MpeBgpPeerEntry 18 }
fsMIBgp4mpebgpPeerConnectRetryInterval OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the ConnectRetry timer. The suggested
value for this timer is 120 seconds."
::= { fsMIBgp4MpeBgpPeerEntry 19 }
fsMIBgp4mpebgpPeerHoldTime OBJECT-TYPE
SYNTAX Integer32 ( 0 | 3..65535 )
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time interval in seconds for the Hold Timer established with the
peer. The value of this object is calculated by this BGP speaker
by using the smaller of the value in bgpPeerHoldTimeConfigured and
the Hold Time received in the OPEN message. This value must be at
lease three seconds if it is not zero (0) in which case the Hold
Timer has not been established with the peer, or, the value of
bgpPeerHoldTimeConfigured is zero (0)."
::= { fsMIBgp4MpeBgpPeerEntry 20 }
fsMIBgp4mpebgpPeerKeepAlive OBJECT-TYPE
SYNTAX Integer32 ( 0 | 1..21845 )
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time interval in seconds for the KeepAlive timer established with
the peer. The value of this object is calculated by this BGP
speaker such that, when compared with bgpPeerHoldTime, it has the
same proportion as what bgpPeerKeepAliveConfigured has when compared
with bgpPeerHoldTimeConfigured. If the value of this object is
zero (0), it indicates that the KeepAlive timer has not been
established with the peer, or, the value of bgpPeerKeepAliveConfigured
is zero (0)."
::= { fsMIBgp4MpeBgpPeerEntry 21 }
fsMIBgp4mpebgpPeerHoldTimeConfigured OBJECT-TYPE
SYNTAX Integer32 ( 0 | 3..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the Hold Time configured for this
BGP speaker with this peer. This value is placed in an OPEN
message sent to this peer by this BGP speaker, and is compared
with the Hold Time field in an OPEN message received from the peer
when determining the Hold Time (bgpPeerHoldTime) with the peer.
This value must not be less than three seconds if it is not zero (0)
in which case the Hold Time is NOT to be established with the peer.
The suggested value for this timer is 90 seconds."
::= { fsMIBgp4MpeBgpPeerEntry 22 }
fsMIBgp4mpebgpPeerKeepAliveConfigured OBJECT-TYPE
SYNTAX Integer32 ( 0 | 1..21845 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the
KeepAlive timer configured for this BGP
speaker with this peer. The value of this
object will only determine the
KEEPALIVE messages' frequency relative to
the value specified in
bgpPeerHoldTimeConfigured; the actual
time interval for the KEEPALIVE messages
is indicated by bgpPeerKeepAlive. A
reasonable maximum value for this timer
would be configured to be one
third of that of
bgpPeerHoldTimeConfigured.
If the value of this object is zero (0),
now periodical KEEPALIVE messages are sent
to the peer after the BGP connection has
been established. The suggested value for
this timer is 30 seconds."
::= { fsMIBgp4MpeBgpPeerEntry 23 }
fsMIBgp4mpebgpPeerMinASOriginationInterval OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the
MinASOriginationInterval timer.
The suggested value for this timer is 15
seconds."
::= { fsMIBgp4MpeBgpPeerEntry 24 }
fsMIBgp4mpebgpPeerMinRouteAdvertisementInterval OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the
MinRouteAdvertisementInterval timer.
The suggested value for this timer is 30
seconds."
::= { fsMIBgp4MpeBgpPeerEntry 25 }
fsMIBgp4mpebgpPeerInUpdateElapsedTime OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Elapsed time in seconds since the last BGP
UPDATE message was received from the peer.
Each time bgpPeerInUpdates is incremented,
the value of this object is set to zero
(0)."
::= { fsMIBgp4MpeBgpPeerEntry 26 }
fsMIBgp4mpebgpPeerEndOfRIBMarkerSentStatus OBJECT-TYPE
SYNTAX INTEGER {
none(0), -- if GR capability is not enabled
true(1),-- End-Of-RIB marker not sent to peer
false(2) -- End-Of-RIB marker sent to peer
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates that whether the End-Of-RIB marker sent to peer or not"
::= { fsMIBgp4MpeBgpPeerEntry 27 }
fsMIBgp4mpebgpPeerEndOfRIBMarkerReceivedStatus OBJECT-TYPE
SYNTAX INTEGER {
none(0),-- If GR capability is not enabled
true(1),-- End-Of-RIB marker not received from peer
false(2) -- End-Of-RIB marker received from peer
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates that whether the End-Of-RIB marker received from peer or not"
::= { fsMIBgp4MpeBgpPeerEntry 28 }
fsMIBgp4mpebgpPeerRestartMode OBJECT-TYPE
SYNTAX INTEGER {
restarting (1),
receiving (2),
none(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the peer BGP speaker is restarting speaker or receiving speaker or not having GR capability"
::= { fsMIBgp4MpeBgpPeerEntry 29 }
fsMIBgp4mpePeerRestartTimeInterval OBJECT-TYPE
SYNTAX Integer32 (1..4096)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the time (in seconds) received from peer through GR capability of open message. This is used in receiving speaker to make sure that the restarting speaker restarted within this interval"
::= { fsMIBgp4MpeBgpPeerEntry 30 }
fsMIBgp4mpePeerAllowAutomaticStart OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This MIB object specifies whether BGP session with the associated peer
can be started automatically. This object when set to 'disabled',
requires manual start for initiating BGP session with the peer via
MIB object 'fsMIBgp4mpebgpPeerAdminStatus'. When set to 'enabled',
the peer session can be automatically started in the IDLE state,
after a BGP Peer session is brought down either by Autostop or via
reception of invalid BGP message. The BGP session will be automatically
started after an interval specified by
'fsMIBgp4mpebgpPeerIdleHoldTimeConfigured'. If
fsMIBgp4mpeDampPeerOscillations is enabled, then automaticStart will not
occur if peer is damped."
DEFVAL { disable }
::= { fsMIBgp4MpeBgpPeerEntry 31 }
fsMIBgp4mpePeerAllowAutomaticStop OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" This MIB object specifies whether a BGP connection needs to be
automatically stopped after a TCP connect-retry count value specified
by MIB object 'fsMIBgp4mpePeerTcpConnectRetryCnt'. The resources
allocated for the BGP peer are released and it continues to remain in
IDLE state. After an automatic stop, the Peer connection needs to be
re-intiated manually by the administrator. When AutomaticStop is
disabled, the connect retry count value is set to 0."
DEFVAL { disable }
::= { fsMIBgp4MpeBgpPeerEntry 32 }
fsMIBgp4mpebgpPeerIdleHoldTimeConfigured OBJECT-TYPE
SYNTAX Integer32 ( 1..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IdleHoldTime specifies the length of time the BGP peer is held in the
Idle state prior to allowing the next automatic restart.
The IdleHoldTime is configured only when the
fsMIBgp4mpePeerAllowAutomaticStart is Enabled or when the
fsMIBgp4mpeDampPeerOscillations is Enabled. The configurable value
differs based on the two options that are enabled.The Suggested default
value is 60 secs for automatic start and after each dampening, the value
of the IdleHoldTime is doubled consecutively."
DEFVAL { 60 }
::= { fsMIBgp4MpeBgpPeerEntry 33 }
fsMIBgp4mpeDampPeerOscillations OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DampPeerOscillations option specifies that the implementation
engages additional logic to damp the oscillations of BGP peers in
the face of series of automatic start and automatic stop operations
in the IDLE state.The DampPeerOscillations option indicates that the
BGP connection is using logic that damps BGP peer oscillations in
states other than 'established' state."
DEFVAL { disable }
::= { fsMIBgp4MpeBgpPeerEntry 34 }
fsMIBgp4mpePeerDelayOpen OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This MIB object allows configuration option to enable/disable delay
in sending of OPEN messages to the BGP peer for a specific time period
(DelayOpenTime). The delay allows the remote BGP Peer to send the first
OPEN message."
DEFVAL { disable }
::= { fsMIBgp4MpeBgpPeerEntry 35 }
fsMIBgp4mpebgpPeerDelayOpenTimeConfigured OBJECT-TYPE
SYNTAX Integer32 ( 0..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DelayOpen time specifies the amount of time the BGP Peer should
delay in sending the OPEN message to the remote peer. If the
fsMIBgp4mpePeerDelayOpen option is enabled, the DelayOpen time can bei
configured. The default value is kept as 0 secs, which implies thati
the BGP Peer can send an OPEN message without any delay to its
neighbor."
DEFVAL { 0 }
::= { fsMIBgp4MpeBgpPeerEntry 36 }
fsMIBgp4mpePeerPrefixUpperLimit OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"BGP speaker imposes a locally-configured, upper bound on the number of
address prefixes the speaker is willing to accept from a neighbor. The
default value is calculated as the following:
fsMIBgp4MaxNoofRoutes / fsMIBgp4MaxPeerEntry
Administrator can configure a value less than the default value at
runtime. Prefixes exceeding the PrefixUpperLimit will not be processedi
by the system."
DEFVAL { 100 }
::= { fsMIBgp4MpeBgpPeerEntry 37 }
fsMIBgp4mpePeerTcpConnectRetryCnt OBJECT-TYPE
SYNTAX Integer32 (1..50)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This counter denotes the Maximum number of times the BGP Peer has
tried to issue a TCP-Connect with its neighboring peers.
The default value for the counter is set as 5."
DEFVAL { 5 }
::= { fsMIBgp4MpeBgpPeerEntry 38 }
fsMIBgp4mpePeerTcpCurrentConnectRetryCnt OBJECT-TYPE
SYNTAX Integer32 (1..50)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" This counter denotes the number of times the BGP Peer has tried to
issue a TCP-Connect with its neighboring peers. It is an internal value.
It increments for each Autostop event. If the
'fsMIBgp4mpePeerTcpCurrentConnectRetryCnt' exceeds the
'fsMIBgp4mpePeerTcpConnectRetryCnt' value, PeerDampening is performed,
provided the corresponding flag is enabled."
::= { fsMIBgp4MpeBgpPeerEntry 39 }
fsMIBgp4mpeIsPeerDamped OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This MIB object specifies the PeerDamped Status. If it is enabled, it
denotes that the peer is in damped state. If it is disabled, it
denotes that either the peer has recovered from the damped state or not
entered into the Damped state. If enabled and if the IdleHold Timer
Threshold value is exceeded, issue Manual Stop, reset the
fsMIBgp4mpePeerTcpCurrentConnectRetryCnt value to zero and disable the
fsMIBgp4mpePeerAllowAutomaticStart."
DEFVAL { disable }
::= { fsMIBgp4MpeBgpPeerEntry 40 }
fsMIBgp4mpePeerSessionAuthStatus OBJECT-TYPE
SYNTAX INTEGER {
nosession (1),
authenticatedMd5 (2),
unauthenticated (3),
authenticatedTcpAo (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether peer-session is TCP MD5/TCP-AO
authenticated or not. If no session is established yet, its value is
no-session"
::= { fsMIBgp4MpeBgpPeerEntry 41 }
fsMIBgp4mpePeerTCPAOKeyIdInUse OBJECT-TYPE
SYNTAX Integer32 (0 .. 255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Key id of the MKT which is used by the TCP session of the peer,
this field will be valid only when fsMIBgp4mpePeerSessionAuthStatus
has value authenticatedTcpAo"
::= { fsMIBgp4MpeBgpPeerEntry 42 }
fsMIBgp4mpePeerTCPAOAuthNoMKTDiscard OBJECT-TYPE
SYNTAX INTEGER
{
accept (1),
discard (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Discard packet for the peer, if packets are received with TCP-AO
and no matching MKT is found, default value is accept"
DEFVAL { accept }
::= { fsMIBgp4MpeBgpPeerEntry 43 }
fsMIBgp4mpePeerTCPAOAuthICMPAccept OBJECT-TYPE
SYNTAX INTEGER
{
accept (1),
ignore (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Accept ICMPv4 type 3 & ICMPv6 type 1 messages for the TCP-AO
authenticated peer, default value is ignore"
DEFVAL { ignore }
::= { fsMIBgp4MpeBgpPeerEntry 44 }
fsMIBgp4mpePeerIpPrefixNameIn OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the IP Prefix list name in IN direction for this peer entry."
::= { fsMIBgp4MpeBgpPeerEntry 45 }
fsMIBgp4mpePeerIpPrefixNameOut OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the IP Prefix list name in OUT direction for this peer entry."
::= { fsMIBgp4MpeBgpPeerEntry 46 }
-- End of Peer Table
-- BGP4 Received Path Attribute Table. This table
-- contains, one entry per path to a network, path
-- attributes received from all peers running BGP-4.
fsMIBgp4MpeBgp4PathAttrTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeBgp4PathAttrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The BGP-4 Received Path Attribute Table
contains information about paths to
destination networks received from all
BGP4 peers."
::= { fsMIBgp 21 }
fsMIBgp4MpeBgp4PathAttrEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeBgp4PathAttrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a path to a network."
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpebgp4PathAttrRouteAfi,
fsMIBgp4mpebgp4PathAttrRouteSafi,
fsMIBgp4mpebgp4PathAttrIpAddrPrefix,
fsMIBgp4mpebgp4PathAttrIpAddrPrefixLen,
fsMIBgp4mpebgp4PathAttrPeerType,
fsMIBgp4mpebgp4PathAttrPeer
}
::= { fsMIBgp4MpeBgp4PathAttrTable 1 }
FsMIBgp4MpeBgp4PathAttrEntry ::= SEQUENCE {
fsMIBgp4mpebgp4PathAttrRouteAfi
InetAddressType,
fsMIBgp4mpebgp4PathAttrRouteSafi
BgpSafi,
fsMIBgp4mpebgp4PathAttrPeerType
InetAddressType,
fsMIBgp4mpebgp4PathAttrPeer
InetAddress,
fsMIBgp4mpebgp4PathAttrIpAddrPrefixLen
Integer32,
fsMIBgp4mpebgp4PathAttrIpAddrPrefix
InetAddress,
fsMIBgp4mpebgp4PathAttrOrigin
INTEGER,
fsMIBgp4mpebgp4PathAttrASPathSegment
OCTET STRING,
fsMIBgp4mpebgp4PathAttrNextHop
InetAddress,
fsMIBgp4mpebgp4PathAttrMultiExitDisc
Integer32,
fsMIBgp4mpebgp4PathAttrLocalPref
Integer32,
fsMIBgp4mpebgp4PathAttrAtomicAggregate
INTEGER,
fsMIBgp4mpebgp4PathAttrAggregatorAS
Unsigned32,
fsMIBgp4mpebgp4PathAttrAggregatorAddr
IpAddress,
fsMIBgp4mpebgp4PathAttrCalcLocalPref
Integer32,
fsMIBgp4mpebgp4PathAttrBest
INTEGER,
fsMIBgp4mpebgp4PathAttrCommunity
OCTET STRING,
fsMIBgp4mpebgp4PathAttrOriginatorId
OCTET STRING,
fsMIBgp4mpebgp4PathAttrClusterList
OCTET STRING,
fsMIBgp4mpebgp4PathAttrExtCommunity
OCTET STRING,
fsMIBgp4mpebgp4PathAttrUnknown
OCTET STRING,
fsMIBgp4mpebgp4PathAttrLabel
OCTET STRING,
fsMIBgp4mpebgp4PathAttrAS4PathSegment
OCTET STRING,
fsMIBgp4mpebgp4PathAttrAggregatorAS4
Unsigned32
}
fsMIBgp4mpebgp4PathAttrRouteAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The AFI of the prefix"
::= { fsMIBgp4MpeBgp4PathAttrEntry 1 }
fsMIBgp4mpebgp4PathAttrRouteSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SAFI of the prefix"
::= { fsMIBgp4MpeBgp4PathAttrEntry 2 }
fsMIBgp4mpebgp4PathAttrPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The AFI of the peer"
::= { fsMIBgp4MpeBgp4PathAttrEntry 3 }
fsMIBgp4mpebgp4PathAttrPeer OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the peer where the path
information was learned."
::= { fsMIBgp4MpeBgp4PathAttrEntry 4 }
fsMIBgp4mpebgp4PathAttrIpAddrPrefixLen OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix
in the Network Layer Reachability
Information field."
::= { fsMIBgp4MpeBgp4PathAttrEntry 5 }
fsMIBgp4mpebgp4PathAttrIpAddrPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address prefix in the Network Layer
Reachability Information field. This object
is an IP address containing the prefix with
length specified by
bgp4PathAttrIpAddrPrefixLen.
Any bits beyond the length specified by
bgp4PathAttrIpAddrPrefixLen are zeroed."
::= { fsMIBgp4MpeBgp4PathAttrEntry 6 }
fsMIBgp4mpebgp4PathAttrOrigin OBJECT-TYPE
SYNTAX INTEGER {
igp(1),-- networks are interior
egp(2),-- networks learned via EGP
incomplete(3) -- undetermined
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ultimate origin of the path
information."
::= { fsMIBgp4MpeBgp4PathAttrEntry 7 }
fsMIBgp4mpebgp4PathAttrASPathSegment OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence of AS path segments. Each AS
path segment is represented by a triple
<type, length, value>.
The type is a 1-octet field which has two
possible values:
1 AS_SET: unordered set of ASs, traversed by a
route in the UPDATE message.
2 AS_SEQUENCE: ordered set of ASs, traversed by
a route in the UPDATE message.
The length is a 1-octet field containing the
number of ASs in the value field.
The value field contains one or more AS
numbers, each AS is represented in the octet
string as a pair of octets according to the
following algorithm:
first-byte-of-pair = ASNumber / 256;
second-byte-of-pair = ASNumber & 255;"
::= { fsMIBgp4MpeBgp4PathAttrEntry 8 }
fsMIBgp4mpebgp4PathAttrNextHop OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the border router that
should be used for the destination network."
::= { fsMIBgp4MpeBgp4PathAttrEntry 9 }
fsMIBgp4mpebgp4PathAttrMultiExitDisc OBJECT-TYPE
SYNTAX Integer32 (-1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This metric is used to discriminate
between multiple exit points to an
adjacent autonomous system. A value of -1
indicates the absence of this attribute."
::= { fsMIBgp4MpeBgp4PathAttrEntry 10 }
fsMIBgp4mpebgp4PathAttrLocalPref OBJECT-TYPE
SYNTAX Integer32 (-1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The originating BGP4 speaker's degree of
preference for an advertised route. A
value of -1 indicates the absence of this
attribute."
::= { fsMIBgp4MpeBgp4PathAttrEntry 11 }
fsMIBgp4mpebgp4PathAttrAtomicAggregate OBJECT-TYPE
SYNTAX INTEGER {
lessSpecificRrouteNotSelected(1),
lessSpecificRouteSelected(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether or not the local system has
selected a less specific route without
selecting a more specific route."
::= { fsMIBgp4MpeBgp4PathAttrEntry 12 }
fsMIBgp4mpebgp4PathAttrAggregatorAS OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The AS number of the last BGP4 speaker that
performed route aggregation. A value of
zero (0) indicates the absence of this
attribute."
::= { fsMIBgp4MpeBgp4PathAttrEntry 13 }
fsMIBgp4mpebgp4PathAttrAggregatorAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of the last BGP4 speaker
that performed route aggregation. A value
of 0.0.0.0 indicates the absence of this
attribute."
::= { fsMIBgp4MpeBgp4PathAttrEntry 14 }
fsMIBgp4mpebgp4PathAttrCalcLocalPref OBJECT-TYPE
SYNTAX Integer32 (-1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The degree of preference calculated by the
receiving BGP4 speaker for an advertised
route. A value of -1 indicates the
absence of this attribute."
::= { fsMIBgp4MpeBgp4PathAttrEntry 15 }
fsMIBgp4mpebgp4PathAttrBest OBJECT-TYPE
SYNTAX INTEGER {
nonbest(1),-- not chosen as best route
best(2), -- chosen as best route
stale(3) -- chosen as stale route
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether or not this route
was chosen as the best BGP4 route."
::= { fsMIBgp4MpeBgp4PathAttrEntry 16 }
fsMIBgp4mpebgp4PathAttrCommunity OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..800))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The community values received for this destinatin
from the peer"
::= { fsMIBgp4MpeBgp4PathAttrEntry 17 }
fsMIBgp4mpebgp4PathAttrOriginatorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Originator-ID identifying the router that initially
advertised this destination to a Route Reflector.
A value of 0.0.0.0 indicates the absence of this attribute"
REFERENCE
"This attribute is defined in [RFC 2796]"
::= { fsMIBgp4MpeBgp4PathAttrEntry 18 }
fsMIBgp4mpebgp4PathAttrClusterList OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..4096))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A sequence of four octet long values Cluster-IDs representing
the reflection path that the route has passed. Each four octet
long value represents the ID of a cluster that the route has
traversed. A length of zero (0) indicates the absence of this
attibute."
REFERENCE
"This attribute is defined in [RFC 2796]"
::= { fsMIBgp4MpeBgp4PathAttrEntry 19 }
fsMIBgp4mpebgp4PathAttrExtCommunity OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..800))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The extended community values received for this
destinatin from the peer"
::= { fsMIBgp4MpeBgp4PathAttrEntry 20 }
fsMIBgp4mpebgp4PathAttrUnknown OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One or more path attributes not understood
by this BGP4 speaker. Size zero (0)
indicates the absence of such
attribute(s). Octets beyond the maximum
size, if any, are not recorded by this
object."
::= { fsMIBgp4MpeBgp4PathAttrEntry 21 }
fsMIBgp4mpebgp4PathAttrLabel OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..24))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"MPLS Label received for this destination from the peer "
::= { fsMIBgp4MpeBgp4PathAttrEntry 22 }
fsMIBgp4mpebgp4PathAttrAS4PathSegment OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence of AS path segments. Each AS
path segment is represented by a triple
<type, length, value>.
The type is a 1-octet field which has two
possible values:
1 AS_SET: unordered set of ASs, traversed by a
route in the UPDATE message.
2 AS_SEQUENCE: ordered set of ASs, traversed by
a route in the UPDATE message.
The length is a 1-octet field containing the
number of ASs in the value field.
The value field contains one or more AS
numbers, each AS is represented in the octet
string as 2 pairs of octets"
REFERENCE
"This attribute is defined in [RFC 6793]"
::= { fsMIBgp4MpeBgp4PathAttrEntry 23 }
fsMIBgp4mpebgp4PathAttrAggregatorAS4 OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 4 Byte AS number of the last BGP4 speaker that
performed route aggregation. A value of
zero (0) indicates the absence of this
attribute."
REFERENCE
"This attribute is defined in [RFC 6793]"
::= { fsMIBgp4MpeBgp4PathAttrEntry 24 }
-- End of Path Attr Table
-- MIB FOR fsMIBgp_PEER_EXTENSIONS_TABLE BEGIN
-- This table is an Extension to the bgpPeerTable from stdbgp4.mib.
-- This table contains, one entry per BGP peer, information
-- about the BGP peer.
fsMIBgp4MpePeerExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpePeerExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP Peer Extension Table. The entries in the table specifies
the additional features supported for a peer by futureBGP4
Speaker in addition to the features specified as in bgpPeerTable
(described in stdbgp4.mib.). All entries in this table can be
configured only if fsMIBgp4LocalAs has be configured."
::= { fsMIBgp 22 }
fsMIBgp4MpePeerExtEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpePeerExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about the additional features supported
for a peer by futureBGP4 Speaker."
INDEX {fsMIBgp4ContextId,
fsMIBgp4mpePeerExtPeerType,
fsMIBgp4mpePeerExtPeerRemoteAddr }
::= { fsMIBgp4MpePeerExtTable 1 }
FsMIBgp4MpePeerExtEntry ::= SEQUENCE {
fsMIBgp4mpePeerExtPeerType
InetAddressType,
fsMIBgp4mpePeerExtPeerRemoteAddr
InetAddress,
fsMIBgp4mpePeerExtConfigurePeer
INTEGER,
fsMIBgp4mpePeerExtPeerRemoteAs
Unsigned32,
fsMIBgp4mpePeerExtEBGPMultiHop
INTEGER,
fsMIBgp4mpePeerExtEBGPHopLimit
Integer32,
fsMIBgp4mpePeerExtNextHopSelf
INTEGER,
fsMIBgp4mpePeerExtRflClient
INTEGER,
fsMIBgp4mpePeerExtTcpSendBufSize
Integer32,
fsMIBgp4mpePeerExtTcpRcvBufSize
Integer32,
fsMIBgp4mpePeerExtLclAddress
InetAddress,
fsMIBgp4mpePeerExtNetworkAddress
InetAddress,
fsMIBgp4mpePeerExtGateway
InetAddress,
fsMIBgp4mpePeerExtCommSendStatus
INTEGER,
fsMIBgp4mpePeerExtECommSendStatus
INTEGER,
fsMIBgp4mpePeerExtPassive
INTEGER,
fsMIBgp4mpePeerExtDefaultOriginate
INTEGER
}
fsMIBgp4mpePeerExtPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Type of the remote peer "
::= { fsMIBgp4MpePeerExtEntry 1 }
fsMIBgp4mpePeerExtPeerRemoteAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote IP address of this entry's BGP peer."
::= { fsMIBgp4MpePeerExtEntry 2 }
fsMIBgp4mpePeerExtConfigurePeer OBJECT-TYPE
SYNTAX INTEGER
{
create (1),
delete (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to create or delete a peer. If called with create
and no matching peer exists, then a new peer entry will be created. The
admin status of this newly created peer will be stop. To enable the peer
set the peers remote AS (fsMIBgp4mpePeerExtPeerRemoteAS)and change the peer's
admin state (bgpPeerAdminState in stdbgp4.mib) to start. If this object
is called with create and a matching peer exists, then no action is done.
If called with delete and if a matching peer exists, then the complete
instance associated with that peer will be deleted."
::= { fsMIBgp4MpePeerExtEntry 3 }
fsMIBgp4mpePeerExtPeerRemoteAs OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The remote autonomous system number of the Peer. The peer admin status
can be made up only if this object is configured for a valid AS number.
When OPEN message is received from this peer during the BGP Connection
establishment, this configured AS value is compared against the AS number
received in the OPEN message. If both matches, then connection
establishment continues. If there is any mismatch, then the connection is
terminated. This object can be set only when the peer's admin status is
down."
::= { fsMIBgp4MpePeerExtEntry 4 }
fsMIBgp4mpePeerExtEBGPMultiHop OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects enables the BGP4 Speaker to accept or attempt
connections to external peers residing on network that are not directly
connected. By default, only directly connected EBGP peers are allowed.
For the internal peers, this object has no effect."
DEFVAL { disable }
::= { fsMIBgp4MpePeerExtEntry 5 }
fsMIBgp4mpePeerExtEBGPHopLimit OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects enables the BGP4 Speaker to accept or attempt
connections to external peers residing on network that are not directly
connected and seperated by a maximum hop limit as configured by this
object. For the internal peers, this object has no effect."
DEFVAL { 1 }
::= { fsMIBgp4MpePeerExtEntry 6 }
fsMIBgp4mpePeerExtNextHopSelf OBJECT-TYPE
SYNTAX INTEGER
{
automatic(1),
self(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies how the next hop attribute sent in the update
messages to this peer has to be generated. When the object takes the
value of self,the next Hop attribute will always be the sender Local
Address else the next hop will be generated based on the IP address of
the destination and the present next hop in the route information."
DEFVAL { automatic }
::= { fsMIBgp4MpePeerExtEntry 7 }
fsMIBgp4mpePeerExtRflClient OBJECT-TYPE
SYNTAX INTEGER
{
nonClient (1),
client (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the peer is Client peer or Non-Client
peer. By default, the peer is created as Non-Client Peer."
DEFVAL {1}
::= { fsMIBgp4MpePeerExtEntry 8 }
fsMIBgp4mpePeerExtTcpSendBufSize OBJECT-TYPE
SYNTAX Integer32 (4096..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the tcp window size on the sender side."
DEFVAL { 65536 }
::= { fsMIBgp4MpePeerExtEntry 9 }
fsMIBgp4mpePeerExtTcpRcvBufSize OBJECT-TYPE
SYNTAX Integer32 (4096..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the tcp window size on the receiver side."
DEFVAL { 65536 }
::= { fsMIBgp4MpePeerExtEntry 10 }
fsMIBgp4mpePeerExtLclAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies which address should be used as the source address
of the TCP session initiated with the Peer. By default this object takes
value as 0 and the source address of the TCP session is filled by TCP.
This object can take value of any interface address. If this object
refers to a valid interface address, then the TCP session initiated
with the peer should have this interface address as the source address."
::= { fsMIBgp4MpePeerExtEntry 11 }
fsMIBgp4mpePeerExtNetworkAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the remote peer's network address. TCP connection is
established using the peer's remote-address. If the peer's remote-address
is a IPv4 address, the peer's network address carries the IPv6 network
address. Similarly, if the peer's remote-address is a IPv6 address, the
peer's network address carries the IPv4 network address. This object can
be configured only after the peer's remote-address and the corresponding
local interface are configured."
::= { fsMIBgp4MpePeerExtEntry 12 }
fsMIBgp4mpePeerExtGateway OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the gateway router's address that will be used as
nexthop in the routes advertised to the peer. This ensures that the
traffic coming from this peer is routed through this gateway."
::= { fsMIBgp4MpePeerExtEntry 13 }
fsMIBgp4mpePeerExtCommSendStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
send (2),
donotsend (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Community Send status of the peer.
o none - is for read-only
o send - send communities to this peer
o donotsend - do not send communities to this peer."
DEFVAL { send }
::= { fsMIBgp4MpePeerExtEntry 14 }
fsMIBgp4mpePeerExtECommSendStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
send (2),
donotsend (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Extended Community Send status of the peer.
o none - is for read-only
o send - send extended communities to this peer
o donotsend - do not send extended communities to this peer."
DEFVAL { send }
::= { fsMIBgp4MpePeerExtEntry 15 }
fsMIBgp4mpePeerExtPassive OBJECT-TYPE
SYNTAX INTEGER
{
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to set a peer connection to be passive, that means
the speaker will not initiate the session with that peer instead it
waits for the remote peer to initiate the session"
::= { fsMIBgp4MpePeerExtEntry 16 }
fsMIBgp4mpePeerExtDefaultOriginate OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to enable/disable the advertisement of the default
route to the peer. This object overrides the global default
route configuration (fsMIBgp4DefaultOriginate) and always send a default
route to the peer with self next-hop. This advertisement occurs
irrespective of the presence of default route in FDB. This object can
be set only if the fsMIBgp4LocalAs is set."
DEFVAL { disable }
::= { fsMIBgp4MpePeerExtEntry 17 }
-- MIB FOR fsMIBgp_PEER_EXTENSIONS_TABLE END
--- Multi-Exit Discriminator Table
--- This table specifies the value that has to be assigned to the
--- Multi-Exit Discriminator attribute when an update is sent.
fsMIBgp4MpeMEDTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeMEDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP4 MED table. This table contains the MED values that are to
be assigned to routes."
::= { fsMIBgp 23 }
fsMIBgp4MpeMEDEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeMEDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about the MED value."
INDEX { fsMIBgp4mpeMEDIndex }
::= { fsMIBgp4MpeMEDTable 1 }
FsMIBgp4MpeMEDEntry ::= SEQUENCE {
fsMIBgp4mpeMEDIndex
Integer32,
fsMIBgp4mpeMEDAdminStatus
INTEGER,
fsMIBgp4mpeMEDRemoteAS
Unsigned32,
fsMIBgp4mpeMEDIPAddrAfi
InetAddressType,
fsMIBgp4mpeMEDIPAddrSafi
BgpSafi,
fsMIBgp4mpeMEDIPAddrPrefix
InetAddress,
fsMIBgp4mpeMEDIPAddrPrefixLen
Integer32,
fsMIBgp4mpeMEDIntermediateAS
DisplayString,
fsMIBgp4mpeMEDDirection
INTEGER,
fsMIBgp4mpeMEDValue
Unsigned32,
fsMIBgp4mpeMEDPreference
INTEGER,
fsMIBgp4mpeMEDVrfName
DisplayString
}
fsMIBgp4mpeMEDIndex OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" This is the index to the table. Any entry in the table can be
configured only if fsMIBgp4LocalAs is set."
::= { fsMIBgp4MpeMEDEntry 1 }
fsMIBgp4mpeMEDAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of this entry. The entries in a row are
configurable only if the admin status is DOWN."
::= { fsMIBgp4MpeMEDEntry 2 }
fsMIBgp4mpeMEDRemoteAS OBJECT-TYPE
SYNTAX Unsigned32 ( 0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The remote autonomous system with which this entry is associated.
A value of zero indicates that this entry is not valid and will not
be matched for when the MED value for an update is calculated."
DEFVAL { 0 }
::= { fsMIBgp4MpeMEDEntry 3 }
fsMIBgp4mpeMEDIPAddrAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of IP address prefix in the Network Layer Reachability Information
field in updates. This field needs to be set before setting the object
fsMIBgp4mpeMEDIPAddrPrefix."
::= { fsMIBgp4MpeMEDEntry 4 }
fsMIBgp4mpeMEDIPAddrSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of IP address prefix in the Network Layer Reachability Information
field in updates. This field needs to be set before setting the object
fsMIBgp4mpeMEDIPAddrPrefix."
::= { fsMIBgp4MpeMEDEntry 5 }
fsMIBgp4mpeMEDIPAddrPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An IP address prefix in the Network Layer Reachability Information
field in updates. A value of zero indicates that the entry is not
valid and will not be matched for when the MED value for an update is
calculated."
DEFVAL { '00000000'H }
::= { fsMIBgp4MpeMEDEntry 6 }
fsMIBgp4mpeMEDIPAddrPrefixLen OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix in the Network Layer Reachability
Information field. A value of zero indicates that the entry is not
valid and will not be matched for when the MED value for an update is
calculated."
DEFVAL { 0 }
::= { fsMIBgp4MpeMEDEntry 7 }
fsMIBgp4mpeMEDIntermediateAS OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Comma seperated list of AS numbers that are to
be checked against the AS_PATH attribute of the Update.
An empty field indicates that the same need not be
checked for in the update.Maximum configurable size is 100."
::= { fsMIBgp4MpeMEDEntry 8 }
fsMIBgp4mpeMEDDirection OBJECT-TYPE
SYNTAX INTEGER {
in(1),
out(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The direction of the update with which the entry is to be associated."
DEFVAL { in }
::= { fsMIBgp4MpeMEDEntry 9 }
fsMIBgp4mpeMEDValue OBJECT-TYPE
SYNTAX Unsigned32 ( 0 .. 2147483647 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value assigned to the MED Attribute for the route present in NLRI"
DEFVAL { 0 }
::= { fsMIBgp4MpeMEDEntry 10 }
fsMIBgp4mpeMEDPreference OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the value present
in this entry takes precedence when the attribute
is already present in the update message that has
been received."
DEFVAL { false }
::= { fsMIBgp4MpeMEDEntry 11 }
fsMIBgp4mpeMEDVrfName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The human-readable name of the VPN."
::= { fsMIBgp4MpeMEDEntry 12 }
-- Local Preference Table.
-- This table specifies the value that has to assigned to the
-- Local Preference attribute when an update is sent to an
-- internal Peer or received from an external or internal peer.
fsMIBgp4MpeLocalPrefTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeLocalPrefEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP Local Preference table. This table contains,
the value that is to be assigned to the Local
Preference attibute."
::= { fsMIBgp 24 }
fsMIBgp4MpeLocalPrefEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeLocalPrefEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about the connection with a BGP peer."
INDEX { fsMIBgp4mpeLocalPrefIndex }
::= { fsMIBgp4MpeLocalPrefTable 1 }
FsMIBgp4MpeLocalPrefEntry ::= SEQUENCE {
fsMIBgp4mpeLocalPrefIndex
Integer32,
fsMIBgp4mpeLocalPrefAdminStatus
INTEGER,
fsMIBgp4mpeLocalPrefRemoteAS
Unsigned32,
fsMIBgp4mpeLocalPrefIPAddrAfi
InetAddressType,
fsMIBgp4mpeLocalPrefIPAddrSafi
BgpSafi,
fsMIBgp4mpeLocalPrefIPAddrPrefix
InetAddress,
fsMIBgp4mpeLocalPrefIPAddrPrefixLen
Integer32,
fsMIBgp4mpeLocalPrefIntermediateAS
DisplayString,
fsMIBgp4mpeLocalPrefDirection
INTEGER,
fsMIBgp4mpeLocalPrefValue
Unsigned32,
fsMIBgp4mpeLocalPrefPreference
INTEGER,
fsMIBgp4mpeLocalPrefVrfName
DisplayString
}
fsMIBgp4mpeLocalPrefIndex OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is the index to the table. Any entry in the table can be
configured only if fsMIBgp4mpeLocalAs is set."
::= { fsMIBgp4MpeLocalPrefEntry 1 }
fsMIBgp4mpeLocalPrefAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of this entry. The entries in a row are
configurable only if the admin status is DOWN."
::= { fsMIBgp4MpeLocalPrefEntry 2 }
fsMIBgp4mpeLocalPrefRemoteAS OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The remote autonomous system with which this entry
is associated. A value of zero indicates that this
entry is not valid and will not be matched for when
the LocalPref value for an update is calculated."
DEFVAL { 0 }
::= { fsMIBgp4MpeLocalPrefEntry 3 }
fsMIBgp4mpeLocalPrefIPAddrAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of IP address prefix in the Network Layer Reachability
Information field. This field needs to be set before setting the object
fsMIBgp4mpeLocalPrefIPAddrPrefix."
::= { fsMIBgp4MpeLocalPrefEntry 4 }
fsMIBgp4mpeLocalPrefIPAddrSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Sub-sequent address family of IP address prefix in the
Network Layer Reachability Information field.This field needs to be set
before setting the object fsMIBgp4mpeLocalPrefIPAddrPrefix. "
::= { fsMIBgp4MpeLocalPrefEntry 5 }
fsMIBgp4mpeLocalPrefIPAddrPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An IP address prefix in the Network Layer Reachability Information field.
A value of zero indicates that the entry is not valid and will not be
matched for when the Local Pref value for an update is calculated."
DEFVAL { '00000000'H }
::= { fsMIBgp4MpeLocalPrefEntry 6 }
fsMIBgp4mpeLocalPrefIPAddrPrefixLen OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix in the Network Layer Reachability
Information field. A value of zero indicates that the entry is not valid
and will not be matched for when the Local Pref value for an update
is calculated."
DEFVAL { 0 }
::= { fsMIBgp4MpeLocalPrefEntry 7 }
fsMIBgp4mpeLocalPrefIntermediateAS OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Comma separated list of AS numbers that are to
be present in the AS_PATH attribute of the Update.
An empty field indicates that the same need not be
checked for in the update.Maximum configurable size is 100."
::= { fsMIBgp4MpeLocalPrefEntry 8 }
fsMIBgp4mpeLocalPrefDirection OBJECT-TYPE
SYNTAX INTEGER {
in(1), -- incoming updates
out(2) -- outgoing updates
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The direction of the update with which the entry is to be associated."
DEFVAL { in }
::= { fsMIBgp4MpeLocalPrefEntry 9 }
fsMIBgp4mpeLocalPrefValue OBJECT-TYPE
SYNTAX Unsigned32 ( 0 .. 2147483647 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value assigned to the LP Attribute for the route present in NLRI"
DEFVAL { 100 }
::= { fsMIBgp4MpeLocalPrefEntry 10 }
fsMIBgp4mpeLocalPrefPreference OBJECT-TYPE
SYNTAX INTEGER {
false(1),
true(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the value present
in this entry takes precedence when the attribute
is already present in the update message that has
been received."
DEFVAL { false }
::= { fsMIBgp4MpeLocalPrefEntry 11 }
fsMIBgp4mpeLocalPrefVrfName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The human-readable name of the VPN."
::= { fsMIBgp4MpeLocalPrefEntry 12 }
-- End of Local Preference Table
-- Update Filter Table.
-- This table is used to filter out routing updates
fsMIBgp4MpeUpdateFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeUpdateFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP Update Filter Table. This table contains
Rules to filter out updates based on the AS from
which it is received, NLRI and AS through which it
had passed."
::= { fsMIBgp 25 }
fsMIBgp4MpeUpdateFilterEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeUpdateFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about the updates
that are to be filtered."
INDEX { fsMIBgp4mpeUpdateFilterIndex }
::= { fsMIBgp4MpeUpdateFilterTable 1 }
FsMIBgp4MpeUpdateFilterEntry ::= SEQUENCE {
fsMIBgp4mpeUpdateFilterIndex
Integer32,
fsMIBgp4mpeUpdateFilterAdminStatus
INTEGER,
fsMIBgp4mpeUpdateFilterRemoteAS
Unsigned32,
fsMIBgp4mpeUpdateFilterIPAddrAfi
InetAddressType,
fsMIBgp4mpeUpdateFilterIPAddrSafi
BgpSafi,
fsMIBgp4mpeUpdateFilterIPAddrPrefix
InetAddress,
fsMIBgp4mpeUpdateFilterIPAddrPrefixLen
Integer32,
fsMIBgp4mpeUpdateFilterIntermediateAS
DisplayString,
fsMIBgp4mpeUpdateFilterDirection
INTEGER,
fsMIBgp4mpeUpdateFilterAction
INTEGER,
fsMIBgp4mpeUpdateFilterVrfName
DisplayString
}
fsMIBgp4mpeUpdateFilterIndex OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is the index to the table. Any entry in the table can be configured
only if fsMIBgp4LocalAs is set."
::= { fsMIBgp4MpeUpdateFilterEntry 1 }
fsMIBgp4mpeUpdateFilterAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of this entry. The entries in a row are
configurable only if the admin status is DOWN."
::= { fsMIBgp4MpeUpdateFilterEntry 2 }
fsMIBgp4mpeUpdateFilterRemoteAS OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The remote autonomous system with which this entry
is associated. A value of zero indicates that this
entry is not valid and will not be matched for when
the update is checked."
DEFVAL { 0 }
::= { fsMIBgp4MpeUpdateFilterEntry 3 }
fsMIBgp4mpeUpdateFilterIPAddrAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of IP address prefix in the Network Layer Reachability
Information field. This field needs to be set, before setting the object
fsMIBgp4mpeUpdateFilterIPAddrPrefix."
::= { fsMIBgp4MpeUpdateFilterEntry 4 }
fsMIBgp4mpeUpdateFilterIPAddrSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"SAFI of IP address prefix in the Network Layer Reachability
Information field. This field needs to be set, before setting the object
fsMIBgp4mpeUpdateFilterIPAddrPrefix."
::= { fsMIBgp4MpeUpdateFilterEntry 5 }
fsMIBgp4mpeUpdateFilterIPAddrPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An IP address prefix in the Network Layer Reachability Information field.
A value of zero in this field indicates that the NLRI field may not be
matched."
DEFVAL { '00000000'H }
::= { fsMIBgp4MpeUpdateFilterEntry 6 }
fsMIBgp4mpeUpdateFilterIPAddrPrefixLen OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix
in the Network Layer Reachability
Information field. A value of zero in this field
indicates that the NLRI field may not be matched."
DEFVAL { 0 }
::= { fsMIBgp4MpeUpdateFilterEntry 7 }
fsMIBgp4mpeUpdateFilterIntermediateAS OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Comma separated list of AS numbers that are to
be present in the AS_PATH attribute of the Update.
An empty field indicates that the same need not be
checked for in the update."
::= { fsMIBgp4MpeUpdateFilterEntry 8 }
fsMIBgp4mpeUpdateFilterDirection OBJECT-TYPE
SYNTAX INTEGER {
in(1), -- incoming updates
out(2) -- outgoing updates
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The direction of the update with which the entry is to be associated."
DEFVAL { in }
::= { fsMIBgp4MpeUpdateFilterEntry 9 }
fsMIBgp4mpeUpdateFilterAction OBJECT-TYPE
SYNTAX INTEGER {
allow (1), -- do not filter
filter (2) -- filter
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The action to be taken when the characteristics
that are specified in the entry is matched."
DEFVAL { filter }
::= { fsMIBgp4MpeUpdateFilterEntry 10 }
fsMIBgp4mpeUpdateFilterVrfName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The human-readable name of the VPN."
::= { fsMIBgp4MpeUpdateFilterEntry 11 }
-- End of Update Filter Table
-- Aggregation Table.
-- This table is used to aggregate the routing information
-- before the same are advertised to peers.
fsMIBgp4MpeAggregateTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeAggregateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP Aggregate Table. The entries in the table
specifies the IP address based on which the routing
information has to be aggregated."
::= { fsMIBgp 26 }
fsMIBgp4MpeAggregateEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeAggregateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about the IP address
on which the aggregation has to be done."
INDEX { fsMIBgp4mpeAggregateIndex }
::= { fsMIBgp4MpeAggregateTable 1 }
FsMIBgp4MpeAggregateEntry ::= SEQUENCE {
fsMIBgp4mpeAggregateIndex
Integer32,
fsMIBgp4mpeAggregateAdminStatus
INTEGER,
fsMIBgp4mpeAggregateIPAddrAfi
InetAddressType,
fsMIBgp4mpeAggregateIPAddrSafi
BgpSafi,
fsMIBgp4mpeAggregateIPAddrPrefix
InetAddress,
fsMIBgp4mpeAggregateIPAddrPrefixLen
Integer32,
fsMIBgp4mpeAggregateAdvertise
INTEGER,
fsMIBgp4mpeAggregateVrfName
DisplayString,
fsMIBgp4mpeAggregateAsSet
INTEGER,
fsMIBgp4mpeAggregateAdvertiseRouteMapName
DisplayString,
fsMIBgp4mpeAggregateSuppressRouteMapName
DisplayString,
fsMIBgp4mpeAggregateAttributeRouteMapName
DisplayString
}
fsMIBgp4mpeAggregateIndex OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is the index to the table.Any entry in the table can be
configured only if fsMIBgp4LocalAs is set."
::= { fsMIBgp4MpeAggregateEntry 1 }
fsMIBgp4mpeAggregateAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
invalid(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of this entry. When the adminstatus is set to up,
the aggregate entry will be made active and the aggregate route
will be formed for this entry. When the adminstatus is set to down,
the aggregate route, if advertised will be withdrawn and the
more-specific routes will be advertised. When the adminstatus is
set to invalid, the aggregate entry will be deleted."
::= { fsMIBgp4MpeAggregateEntry 2 }
fsMIBgp4mpeAggregateIPAddrAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of IP address prefix in the Network Layer Reachability
Information field. This field needs to be set before setting the object
fsMIBgp4mpeAggregateIPAddrPrefix. "
::= { fsMIBgp4MpeAggregateEntry 3 }
fsMIBgp4mpeAggregateIPAddrSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"SAFI of IP address prefix in the Network Layer Reachability
Information field. This field needs to be set before setting the object
fsMIBgp4mpeAggregateIPAddrPrefix..
[Note] SAFI for Carrying Label (4) can't be set. The configuration with
SAFI unicast(1) holds good for both labelled and unlabelled prefixes."
::= { fsMIBgp4MpeAggregateEntry 4 }
fsMIBgp4mpeAggregateIPAddrPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An IP address prefix in the Network Layer Reachability Information field.
This field is configurable only if the admin status is DOWN"
::= { fsMIBgp4MpeAggregateEntry 5 }
fsMIBgp4mpeAggregateIPAddrPrefixLen OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix in the Network Layer Reachability
Information field. This field is configurable only if the admin status
is DOWN."
::= { fsMIBgp4MpeAggregateEntry 6 }
fsMIBgp4mpeAggregateAdvertise OBJECT-TYPE
SYNTAX INTEGER {
summaryOnly (1),
all (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the route update that should be sent
to the peers -
summary-only - specifies that only the summarized route
has to be advertised to peers.
All - specifies that both the summary and the
more-specific routes based on which the summary entry
was generated has to be advertised to the peers."
::= { fsMIBgp4MpeAggregateEntry 7 }
fsMIBgp4mpeAggregateVrfName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The human-readable name of the VPN."
::= { fsMIBgp4MpeAggregateEntry 8 }
fsMIBgp4mpeAggregateAsSet OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables/Disables the autonomous system set path information.
It is an optional parameter "
::= { fsMIBgp4MpeAggregateEntry 9 }
fsMIBgp4mpeAggregateAdvertiseRouteMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..20))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The human-readable name for adverise route-map. The route map contains
the rules for advertising the routes while aggregation. When we use
advertise-map, only advertise-map influences the creation of aggregate
entry. In absence of advertise-map, the aggregate route inherits the
attributes of the more specific routes, both suppressed and unsuppressed.
When advertise-map is used with fsMIBgp4mpeAggregateAsSet (as enable) and
suppress map, the aggregate inherits the attributes of only the routes
that are selected in the advertise-map, irrespective of whether
suppress-map suppresses the routes."
::= { fsMIBgp4MpeAggregateEntry 10 }
fsMIBgp4mpeAggregateSuppressRouteMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..20))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The human-readable name for suppress route-map. The route map contains
the rules for suppressing the routes while aggregation. when we use
suppress-map configuration along with (summaryonly option set for)
fsMIBgp4mpeAggregateAdvertise, it does'nt have any effect. And the
more-specific routes that the suppress-map suppresses are not
advertised. Other routes are advertised. When we use
fsMIBgp4mpeAggregateAsSet (with enabled option) with suppress-map although
suppress routes are not advertised, the aggregated routes inherits the
attributes of all the suppressesed rotues. But it can be overwritten by
attribute-map."
::= { fsMIBgp4MpeAggregateEntry 11 }
fsMIBgp4mpeAggregateAttributeRouteMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..20))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The human-readable name for attribute route-map. The route map contains
the rules for setting the attributes the aggregated route. When
attribute-map and advertise-map along with fsMIBgp4mpeAggregateAsSet (enable)
and other configurations, the attribute-map overrides the attribute that
are configured in the attribute-map."
::= { fsMIBgp4MpeAggregateEntry 12 }
-- End of Aggregation Table
-- SCALAR_TABLE_END fsMIBgp4RRDGroup
-- RRD OBJECT DEFINITION END
-- MIB for Importing STATIC routes to BGP and Viewing non-BGP routes.
-- Start of Import Route Table
fsMIBgp4MpeImportRouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeImportRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Non-BGP routes imported into the BGP RIB can be viewed through this table.
Also allows importing a static route into BGP.After updating the RIB tree,
if there is any change in the best route selected, then the route is
updated to the Common Forwarding table."
::= { fsMIBgp 27 }
fsMIBgp4MpeImportRouteEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeImportRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Import Route entry."
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpeImportRoutePrefixAfi,
fsMIBgp4mpeImportRoutePrefixSafi,
fsMIBgp4mpeImportRoutePrefix,
fsMIBgp4mpeImportRoutePrefixLen,
fsMIBgp4mpeImportRouteProtocol,
fsMIBgp4mpeImportRouteNextHop,
fsMIBgp4mpeImportRouteIfIndex,
fsMIBgp4mpeImportRouteMetric,
fsMIBgp4mpeImportRouteVrf
}
::= { fsMIBgp4MpeImportRouteTable 1 }
FsMIBgp4MpeImportRouteEntry ::= SEQUENCE {
fsMIBgp4mpeImportRoutePrefixAfi InetAddressType,
fsMIBgp4mpeImportRoutePrefixSafi BgpSafi,
fsMIBgp4mpeImportRoutePrefix InetAddress,
fsMIBgp4mpeImportRoutePrefixLen Integer32,
fsMIBgp4mpeImportRouteProtocol Integer32,
fsMIBgp4mpeImportRouteNextHop InetAddress,
fsMIBgp4mpeImportRouteIfIndex Integer32,
fsMIBgp4mpeImportRouteMetric Integer32,
fsMIBgp4mpeImportRouteVrf DisplayString,
fsMIBgp4mpeImportRouteAction INTEGER
}
fsMIBgp4mpeImportRoutePrefixAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Type of Prefix of the route to be imported."
::= { fsMIBgp4MpeImportRouteEntry 1 }
fsMIBgp4mpeImportRoutePrefixSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI of Prefix of the route to be imported. Only UNICAST (1) is allowed
right now. Route can be imported into VRF by providing SAFI (1) and
VRF name."
::= { fsMIBgp4MpeImportRouteEntry 2 }
fsMIBgp4mpeImportRoutePrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Prefix of the route to be imported."
::= { fsMIBgp4MpeImportRouteEntry 3 }
fsMIBgp4mpeImportRoutePrefixLen OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Prefix length of the route."
::= { fsMIBgp4MpeImportRouteEntry 4 }
fsMIBgp4mpeImportRouteProtocol OBJECT-TYPE
SYNTAX Integer32 (2|3|8|13)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Protocol value for Non-BGP routes.
2- LOCAL,
3 - STATIC,
8 - RIP,
13 - OSPF.
Only STATIC routes (protocol 3) can be added through this table.
However all non-BGP protocol (Local, Static, RIP, OSPF) routes can
be viewed."
::= { fsMIBgp4MpeImportRouteEntry 5 }
fsMIBgp4mpeImportRouteNextHop OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"NextHop Ipaddress for the route."
::= { fsMIBgp4MpeImportRouteEntry 6 }
fsMIBgp4mpeImportRouteIfIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Interface Index of the Route"
::= { fsMIBgp4MpeImportRouteEntry 7 }
fsMIBgp4mpeImportRouteMetric OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Metric for the route being imported."
::= { fsMIBgp4MpeImportRouteEntry 8 }
fsMIBgp4mpeImportRouteVrf OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Vrf in which the route should be imported. If the rotueis to be installed
in default VRF, the value should be NULL string"
::= { fsMIBgp4MpeImportRouteEntry 9 }
fsMIBgp4mpeImportRouteAction OBJECT-TYPE
SYNTAX INTEGER {
add (1), -- route addition
delete (2) -- route deletion
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls addition or deletion of route."
::= { fsMIBgp4MpeImportRouteEntry 10 }
-- End of Import Route Table
-- MIB for Importing DIRECT/STATIC routes to BGP end
-- MIB for getting FSM transition history
fsMIBgp4MpeFsmTransitionHistTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeFsmTransitionHistEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Gets FSM transitions history per peer"
::= { fsMIBgp 28 }
fsMIBgp4MpeFsmTransitionHistEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeFsmTransitionHistEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Fsm Hist entry."
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpePeerType,
fsMIBgp4mpePeer
}
::= { fsMIBgp4MpeFsmTransitionHistTable 1 }
FsMIBgp4MpeFsmTransitionHistEntry ::= SEQUENCE {
fsMIBgp4mpePeerType InetAddressType,
fsMIBgp4mpePeer InetAddress,
fsMIBgp4mpeFsmTransitionHist DisplayString
}
fsMIBgp4mpePeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Type of Peer from which FSM transition history would be read."
::= { fsMIBgp4MpeFsmTransitionHistEntry 1 }
fsMIBgp4mpePeer OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Peer from which FSM transition history would be read."
::= { fsMIBgp4MpeFsmTransitionHistEntry 2 }
fsMIBgp4mpeFsmTransitionHist OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" sequence of FSM states separated by space"
::= { fsMIBgp4MpeFsmTransitionHistEntry 3 }
-- End of FSM Transition History Table
-- Routes Damping History Table
fsMIBgp4MpeRfd OBJECT IDENTIFIER ::= { fsMIBgp 29 }
fsMIBgp4MpeRfdRtDampHistTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeRfdRtDampHistEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Route damping history table.This table contains the figure-of-merit and
the route status"
::= { fsMIBgp4MpeRfd 1 }
fsMIBgp4MpeRfdRtDampHistEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeRfdRtDampHistEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry contains route damping history"
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpePathAttrAddrPrefixAfi,
fsMIBgp4mpePathAttrAddrPrefixSafi,
fsMIBgp4mpePathAttrAddrPrefix,
fsMIBgp4mpePathAttrAddrPrefixLen,
fsMIBgp4mpePathAttrPeerType,
fsMIBgp4mpePathAttrPeer
}
::= { fsMIBgp4MpeRfdRtDampHistTable 1 }
FsMIBgp4MpeRfdRtDampHistEntry ::= SEQUENCE {
fsMIBgp4mpePathAttrAddrPrefixAfi
InetAddressType,
fsMIBgp4mpePathAttrAddrPrefixSafi
BgpSafi,
fsMIBgp4mpePathAttrAddrPrefix
InetAddress,
fsMIBgp4mpePathAttrAddrPrefixLen
Integer32,
fsMIBgp4mpePathAttrPeerType
InetAddressType,
fsMIBgp4mpePathAttrPeer
InetAddress,
fsMIBgp4mpeRfdRtFom
Integer32,
fsMIBgp4mpeRfdRtLastUpdtTime
Integer32,
fsMIBgp4mpeRfdRtState
INTEGER,
fsMIBgp4mpeRfdRtStatus
INTEGER,
fsMIBgp4mpeRfdRtFlapCount
Integer32,
fsMIBgp4mpeRfdRtFlapTime
Integer32,
fsMIBgp4mpeRfdRtReuseTime
Integer32
}
fsMIBgp4mpePathAttrAddrPrefixAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of the route "
::= { fsMIBgp4MpeRfdRtDampHistEntry 1 }
fsMIBgp4mpePathAttrAddrPrefixSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI of the route "
::= { fsMIBgp4MpeRfdRtDampHistEntry 2 }
fsMIBgp4mpePathAttrAddrPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address prefix in the NLRI field. This object is an IP address
containing the prefix with the length specified by
fsMIBgp4mpePathAttrAddrPrefixLen. Any bits beyond the length specified by
bgp4PathAttrAddrPrefixLen are
zeroed."
::= { fsMIBgp4MpeRfdRtDampHistEntry 3 }
fsMIBgp4mpePathAttrAddrPrefixLen OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix in NLRI field."
::= { fsMIBgp4MpeRfdRtDampHistEntry 4 }
fsMIBgp4mpePathAttrPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of the peer "
::= { fsMIBgp4MpeRfdRtDampHistEntry 5 }
fsMIBgp4mpePathAttrPeer OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Peer remote address of the peer where the path information was
learned."
::= { fsMIBgp4MpeRfdRtDampHistEntry 6 }
fsMIBgp4mpeRfdRtFom OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The figure-of-merit of the route"
::= { fsMIBgp4MpeRfdRtDampHistEntry 7 }
fsMIBgp4mpeRfdRtLastUpdtTime OBJECT-TYPE
SYNTAX Integer32(1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time when the route figure-of-merit was updated."
::= {fsMIBgp4MpeRfdRtDampHistEntry 8 }
fsMIBgp4mpeRfdRtState OBJECT-TYPE
SYNTAX INTEGER {
none(1),
suppressed (2),
unsuppressed (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value gives the status whether the route is suppressed or not "
::= { fsMIBgp4MpeRfdRtDampHistEntry 9 }
fsMIBgp4mpeRfdRtStatus OBJECT-TYPE
SYNTAX INTEGER {
none(1),
feasibleroute (2),
unfeasibleroute (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value gives the status whether the route is feasible or unfeasible
route"
::= { fsMIBgp4MpeRfdRtDampHistEntry 10 }
fsMIBgp4mpeRfdRtFlapCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value gives the number of times the route being flapped"
::= { fsMIBgp4MpeRfdRtDampHistEntry 11 }
fsMIBgp4mpeRfdRtFlapTime OBJECT-TYPE
SYNTAX Integer32(1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time calculated for a route, from when a route is being flapped for
first time, time in seconds"
::= { fsMIBgp4MpeRfdRtDampHistEntry 12 }
fsMIBgp4mpeRfdRtReuseTime OBJECT-TYPE
SYNTAX Integer32(1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time after which a route can be reused again after it moves to
suppressed state from unsuppressed state, time in seconds"
::= { fsMIBgp4MpeRfdRtDampHistEntry 13 }
-- End of routes damping history Table
--- Peers Damping History Table
fsMIBgp4MpeRfdPeerDampHistTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeRfdPeerDampHistEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Peer Damping history table. It contains the peer figure-of-merit and
peer status."
::= { fsMIBgp4MpeRfd 2 }
fsMIBgp4MpeRfdPeerDampHistEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeRfdPeerDampHistEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry contains peer damping history"
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpePeerRemoteIpAddrType,
fsMIBgp4mpePeerRemoteIpAddr
}
::= { fsMIBgp4MpeRfdPeerDampHistTable 1 }
FsMIBgp4MpeRfdPeerDampHistEntry ::= SEQUENCE {
fsMIBgp4mpePeerRemoteIpAddrType
InetAddressType,
fsMIBgp4mpePeerRemoteIpAddr
InetAddress,
fsMIBgp4mpeRfdPeerFom
Integer32,
fsMIBgp4mpeRfdPeerLastUpdtTime
Integer32,
fsMIBgp4mpeRfdPeerState
INTEGER,
fsMIBgp4mpeRfdPeerStatus
INTEGER
}
fsMIBgp4mpePeerRemoteIpAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of the remote peer "
::= { fsMIBgp4MpeRfdPeerDampHistEntry 1 }
fsMIBgp4mpePeerRemoteIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The peer remote address of the peer."
::= { fsMIBgp4MpeRfdPeerDampHistEntry 2 }
fsMIBgp4mpeRfdPeerFom OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current figure-of-merit of peer"
::= {fsMIBgp4MpeRfdPeerDampHistEntry 3 }
fsMIBgp4mpeRfdPeerLastUpdtTime OBJECT-TYPE
SYNTAX Integer32(1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time when the figure-of-merit was updated."
::= {fsMIBgp4MpeRfdPeerDampHistEntry 4 }
fsMIBgp4mpeRfdPeerState OBJECT-TYPE
SYNTAX INTEGER {
none(1),
suppressed (2),
unsuppressed (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value gives the status whether peer is suppressed or not"
::= {fsMIBgp4MpeRfdPeerDampHistEntry 5 }
fsMIBgp4mpeRfdPeerStatus OBJECT-TYPE
SYNTAX INTEGER {
none(1),
peerup (2),
peerdown (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value gives the status whether peer is up or down"
::= {fsMIBgp4MpeRfdPeerDampHistEntry 6 }
-- End of Peer damping history Table
-- Routes Reuse List Table
fsMIBgp4MpeRfdRtsReuseListTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeRfdRtsReuseListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Routes Reuse List Table. It contains the IP prefix and prefix length."
::= { fsMIBgp4MpeRfd 3 }
fsMIBgp4MpeRfdRtsReuseListEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeRfdRtsReuseListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry contains routes reuse list"
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpeRtAfi,
fsMIBgp4mpeRtSafi,
fsMIBgp4mpeRtIPPrefix,
fsMIBgp4mpeRtIPPrefixLen,
fsMIBgp4mpeRfdRtsReusePeerType,
fsMIBgp4mpePeerRemAddress
}
::= { fsMIBgp4MpeRfdRtsReuseListTable 1 }
FsMIBgp4MpeRfdRtsReuseListEntry ::= SEQUENCE {
fsMIBgp4mpeRtAfi
InetAddressType,
fsMIBgp4mpeRtSafi
BgpSafi,
fsMIBgp4mpeRtIPPrefix
InetAddress,
fsMIBgp4mpeRtIPPrefixLen
Integer32,
fsMIBgp4mpeRfdRtsReusePeerType
InetAddressType,
fsMIBgp4mpePeerRemAddress
InetAddress,
fsMIBgp4mpeRfdRtReuseListRtFom
Integer32,
fsMIBgp4mpeRfdRtReuseListRtLastUpdtTime
Integer32,
fsMIBgp4mpeRfdRtReuseListRtState
INTEGER,
fsMIBgp4mpeRfdRtReuseListRtStatus
INTEGER
}
fsMIBgp4mpeRtAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of the route"
::= { fsMIBgp4MpeRfdRtsReuseListEntry 1 }
fsMIBgp4mpeRtSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of the route"
::= { fsMIBgp4MpeRfdRtsReuseListEntry 2 }
fsMIBgp4mpeRtIPPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An IP address prefix in the NLRI field. This object is an IP address
containing the prefix with the length specified by fsMIBgp4RtIPPrefixLen.
Any bits beyond the length specified by fsMIBgp4IPPrefixLen are
zeroed."
::= { fsMIBgp4MpeRfdRtsReuseListEntry 3 }
fsMIBgp4mpeRtIPPrefixLen OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Length in bits of the IP address prefix in NLRI field."
::= { fsMIBgp4MpeRfdRtsReuseListEntry 4 }
fsMIBgp4mpeRfdRtsReusePeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of the remote peer"
::= { fsMIBgp4MpeRfdRtsReuseListEntry 5 }
fsMIBgp4mpePeerRemAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Peer remote address of the peer where the path information was
learned."
::= { fsMIBgp4MpeRfdRtsReuseListEntry 6 }
fsMIBgp4mpeRfdRtReuseListRtFom OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The figure-of-merit of the route which is in the routes reuse list"
::= {fsMIBgp4MpeRfdRtsReuseListEntry 7 }
fsMIBgp4mpeRfdRtReuseListRtLastUpdtTime OBJECT-TYPE
SYNTAX Integer32(1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time when the route figure-of-merit was updated."
::= {fsMIBgp4MpeRfdRtsReuseListEntry 8 }
fsMIBgp4mpeRfdRtReuseListRtState OBJECT-TYPE
SYNTAX INTEGER {
none(1),
suppressed (2),
unsuppressed (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value gives the status whether the route is suppressed or not "
::= { fsMIBgp4MpeRfdRtsReuseListEntry 9 }
fsMIBgp4mpeRfdRtReuseListRtStatus OBJECT-TYPE
SYNTAX INTEGER {
none(1),
feasibleroute (2),
unfeasibleroute (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value gives the status whether the route is feasible or unfeasible
route"
::= { fsMIBgp4MpeRfdRtsReuseListEntry 10 }
-- End of Routes Reuse Table
--- Peer's Reuse List Table
fsMIBgp4MpeRfdPeerReuseListTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeRfdPeerReuseListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Peer's Reuse List Table. It contains the Peer Remote Address."
::= { fsMIBgp4MpeRfd 4 }
fsMIBgp4MpeRfdPeerReuseListEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeRfdPeerReuseListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry contains routes reuse list"
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpeRfdPeerRemIpAddrType,
fsMIBgp4mpeRfdPeerRemIpAddr
}
::= {fsMIBgp4MpeRfdPeerReuseListTable 1 }
FsMIBgp4MpeRfdPeerReuseListEntry ::= SEQUENCE {
fsMIBgp4mpeRfdPeerRemIpAddrType
InetAddressType,
fsMIBgp4mpeRfdPeerRemIpAddr
InetAddress,
fsMIBgp4mpeRfdPeerReuseListPeerFom
Integer32,
fsMIBgp4mpeRfdPeerReuseListLastUpdtTime
Integer32,
fsMIBgp4mpeRfdPeerReuseListPeerState
INTEGER,
fsMIBgp4mpeRfdPeerReuseListPeerStatus
INTEGER
}
fsMIBgp4mpeRfdPeerRemIpAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of the peer"
::= { fsMIBgp4MpeRfdPeerReuseListEntry 1 }
fsMIBgp4mpeRfdPeerRemIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The peer remote address of the peer which is in the peer's reuse list."
::= { fsMIBgp4MpeRfdPeerReuseListEntry 2 }
fsMIBgp4mpeRfdPeerReuseListPeerFom OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current figure-of-merit of peer"
::= {fsMIBgp4MpeRfdPeerReuseListEntry 3 }
fsMIBgp4mpeRfdPeerReuseListLastUpdtTime OBJECT-TYPE
SYNTAX Integer32(1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time when the figure-of-merit was updated."
::= {fsMIBgp4MpeRfdPeerReuseListEntry 4 }
fsMIBgp4mpeRfdPeerReuseListPeerState OBJECT-TYPE
SYNTAX INTEGER {
none(1),
suppressed (2),
unsuppressed (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value gives the status whether peer is suppressed or not"
::= {fsMIBgp4MpeRfdPeerReuseListEntry 5 }
fsMIBgp4mpeRfdPeerReuseListPeerStatus OBJECT-TYPE
SYNTAX INTEGER {
none(1),
peerup (2),
peerdown (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value gives the status whether peer is up or down"
::= {fsMIBgp4MpeRfdPeerReuseListEntry 6 }
-- End of Peer's reuse Table
-- MIB FOR fsMIBgp_ROUTEFLAPDAMPING end
-- MIB FOR fsMIBgp_COMMUNITY
--- Routes Additive Community Table
--- Represents the additive communities configured for
--- destinations.
fsMIBgp4MpeComm OBJECT IDENTIFIER ::= { fsMIBgp 30 }
fsMIBgp4MpeCommRouteAddCommTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeCommRouteAddCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure additive communities
for a given destination."
::= {fsMIBgp4MpeComm 1 }
fsMIBgp4MpeCommRouteAddCommEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeCommRouteAddCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Routes configured additive communities Table Entry"
INDEX {fsMIBgp4ContextId,
fsMIBgp4mpeAddCommRtAfi,
fsMIBgp4mpeAddCommRtSafi,
fsMIBgp4mpeAddCommIpNetwork,
fsMIBgp4mpeAddCommIpPrefixLen,
fsMIBgp4mpeAddCommVal
}
::= { fsMIBgp4MpeCommRouteAddCommTable 1 }
FsMIBgp4MpeCommRouteAddCommEntry ::= SEQUENCE {
fsMIBgp4mpeAddCommRtAfi
InetAddressType,
fsMIBgp4mpeAddCommRtSafi
BgpSafi,
fsMIBgp4mpeAddCommIpNetwork
InetAddress,
fsMIBgp4mpeAddCommIpPrefixLen
Integer32,
fsMIBgp4mpeAddCommVal
Unsigned32,
fsMIBgp4mpeAddCommRowStatus
RowStatus
}
fsMIBgp4mpeAddCommRtAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the destination"
::= { fsMIBgp4MpeCommRouteAddCommEntry 1 }
fsMIBgp4mpeAddCommRtSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI of IP address of the destination"
::= { fsMIBgp4MpeCommRouteAddCommEntry 2 }
fsMIBgp4mpeAddCommIpNetwork OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the destination"
::= { fsMIBgp4MpeCommRouteAddCommEntry 3 }
fsMIBgp4mpeAddCommIpPrefixLen OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP prefix length for the destination"
::= { fsMIBgp4MpeCommRouteAddCommEntry 4 }
fsMIBgp4mpeAddCommVal OBJECT-TYPE
SYNTAX Unsigned32 (65536..4294901759|4294967041..4294967043)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Additive Community configured for the Route"
::= { fsMIBgp4MpeCommRouteAddCommEntry 5 }
fsMIBgp4mpeAddCommRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status for creating entries into this table.This object can be set
only if fsMIBgp4LocalAS is configured."
::= { fsMIBgp4MpeCommRouteAddCommEntry 6 }
-- End of Routes Additive Table
-- Routes Delete Community Table
-- Represents the communities to be deleted for the
-- destinations.
fsMIBgp4MpeCommRouteDeleteCommTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeCommRouteDeleteCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure delete communities
for a given destination."
::= { fsMIBgp4MpeComm 2 }
fsMIBgp4MpeCommRouteDeleteCommEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeCommRouteDeleteCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Routes configured delete communities Table Entry"
INDEX {fsMIBgp4ContextId,
fsMIBgp4mpeDeleteCommRtAfi,
fsMIBgp4mpeDeleteCommRtSafi,
fsMIBgp4mpeDeleteCommIpNetwork,
fsMIBgp4mpeDeleteCommIpPrefixLen,
fsMIBgp4mpeDeleteCommVal
}
::= { fsMIBgp4MpeCommRouteDeleteCommTable 1 }
FsMIBgp4MpeCommRouteDeleteCommEntry ::= SEQUENCE {
fsMIBgp4mpeDeleteCommRtAfi
InetAddressType,
fsMIBgp4mpeDeleteCommRtSafi
BgpSafi,
fsMIBgp4mpeDeleteCommIpNetwork
InetAddress,
fsMIBgp4mpeDeleteCommIpPrefixLen
Integer32,
fsMIBgp4mpeDeleteCommVal
Unsigned32,
fsMIBgp4mpeDeleteCommRowStatus
RowStatus
}
fsMIBgp4mpeDeleteCommRtAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the destination"
::= { fsMIBgp4MpeCommRouteDeleteCommEntry 1 }
fsMIBgp4mpeDeleteCommRtSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI of IP address of the destination"
::= { fsMIBgp4MpeCommRouteDeleteCommEntry 2 }
fsMIBgp4mpeDeleteCommIpNetwork OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the destination"
::= { fsMIBgp4MpeCommRouteDeleteCommEntry 3 }
fsMIBgp4mpeDeleteCommIpPrefixLen OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP prefix length for the destination"
::= { fsMIBgp4MpeCommRouteDeleteCommEntry 4 }
fsMIBgp4mpeDeleteCommVal OBJECT-TYPE
SYNTAX Unsigned32 (65536..4294901759|4294967041..4294967043)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Delete Community configured for the Route"
::= { fsMIBgp4MpeCommRouteDeleteCommEntry 5 }
fsMIBgp4mpeDeleteCommRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status for creating entries into this table.This object can be set
only if fsMIBgp4LocalAS is configured."
::= { fsMIBgp4MpeCommRouteDeleteCommEntry 6 }
-- End of Routes delete community Table
-- Routes Community Set Status Table
-- Represents the status or local policy (can be either, addition of
-- communities, deletion of communities or both or complete
-- ommission of communities) for destinations.
fsMIBgp4MpeCommRouteCommSetStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeCommRouteCommSetStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure the local policy of communities
for a given destination."
::= { fsMIBgp4MpeComm 3 }
fsMIBgp4MpeCommRouteCommSetStatusEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeCommRouteCommSetStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Routes configured delete communities Table Entry"
INDEX {fsMIBgp4ContextId,
fsMIBgp4mpeCommSetStatusAfi,
fsMIBgp4mpeCommSetStatusSafi,
fsMIBgp4mpeCommSetStatusIpNetwork,
fsMIBgp4mpeCommSetStatusIpPrefixLen
}
::= { fsMIBgp4MpeCommRouteCommSetStatusTable 1 }
FsMIBgp4MpeCommRouteCommSetStatusEntry ::= SEQUENCE {
fsMIBgp4mpeCommSetStatusAfi
InetAddressType,
fsMIBgp4mpeCommSetStatusSafi
BgpSafi,
fsMIBgp4mpeCommSetStatusIpNetwork
InetAddress,
fsMIBgp4mpeCommSetStatusIpPrefixLen
Integer32,
fsMIBgp4mpeCommSetStatus
INTEGER,
fsMIBgp4mpeCommSetStatusRowStatus
RowStatus
}
fsMIBgp4mpeCommSetStatusAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the destination"
::= { fsMIBgp4MpeCommRouteCommSetStatusEntry 1 }
fsMIBgp4mpeCommSetStatusSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI of IP address of the destination"
::= { fsMIBgp4MpeCommRouteCommSetStatusEntry 2 }
fsMIBgp4mpeCommSetStatusIpNetwork OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the destination"
::= { fsMIBgp4MpeCommRouteCommSetStatusEntry 3 }
fsMIBgp4mpeCommSetStatusIpPrefixLen OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP prefix length for the destination"
::= { fsMIBgp4MpeCommRouteCommSetStatusEntry 4 }
fsMIBgp4mpeCommSetStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
set (2),
setnone (3),
modify (4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Community Set status for the Route.
o none - is for read-only
o set - to send only with configured additive communities
o setnone - to send without communities,
o modify - to strip delete communities in received
communities and add additive communities
This object can be set only if fsMIBgp4LocalAs is configured."
DEFVAL { 4 }
::= { fsMIBgp4MpeCommRouteCommSetStatusEntry 5 }
fsMIBgp4mpeCommSetStatusRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status for creating entries into this table.
This object can be set only if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4MpeCommRouteCommSetStatusEntry 6 }
-- End of Routes community set status Table
-- MIB FOR fsMIBgp_COMMUNITY end
-- MIB FOR fsMIBgp_EXTCOMM
--- Routes Additive Ext-Community Table
--- Represents the additive extended communities configured for
--- destinations.
fsMIBgp4MpeExtComm OBJECT IDENTIFIER ::= { fsMIBgp 31 }
fsMIBgp4MpeExtCommRouteAddExtCommTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeExtCommRouteAddExtCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure additive extended communities
for a given destination."
::= { fsMIBgp4MpeExtComm 1 }
fsMIBgp4MpeExtCommRouteAddExtCommEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeExtCommRouteAddExtCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Routes configured additive ext-communities Table Entry"
INDEX {fsMIBgp4ContextId,
fsMIBgp4mpeAddExtCommRtAfi,
fsMIBgp4mpeAddExtCommRtSafi,
fsMIBgp4mpeAddExtCommIpNetwork,
fsMIBgp4mpeAddExtCommIpPrefixLen,
fsMIBgp4mpeAddExtCommVal
}
::= { fsMIBgp4MpeExtCommRouteAddExtCommTable 1 }
FsMIBgp4MpeExtCommRouteAddExtCommEntry ::= SEQUENCE {
fsMIBgp4mpeAddExtCommRtAfi
InetAddressType,
fsMIBgp4mpeAddExtCommRtSafi
BgpSafi,
fsMIBgp4mpeAddExtCommIpNetwork
InetAddress,
fsMIBgp4mpeAddExtCommIpPrefixLen
Integer32,
fsMIBgp4mpeAddExtCommVal
OCTET STRING,
fsMIBgp4mpeAddExtCommRowStatus
RowStatus
}
fsMIBgp4mpeAddExtCommRtAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteAddExtCommEntry 1 }
fsMIBgp4mpeAddExtCommRtSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteAddExtCommEntry 2 }
fsMIBgp4mpeAddExtCommIpNetwork OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteAddExtCommEntry 3 }
fsMIBgp4mpeAddExtCommIpPrefixLen OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP prefix length for the destination"
::= { fsMIBgp4MpeExtCommRouteAddExtCommEntry 4 }
fsMIBgp4mpeAddExtCommVal OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Additive Ext-Community for the destination"
::= { fsMIBgp4MpeExtCommRouteAddExtCommEntry 5 }
fsMIBgp4mpeAddExtCommRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status for creating entries into this table.This object can be set
only if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4MpeExtCommRouteAddExtCommEntry 6 }
-- End of Routes Additive Ext-community Table
--- Routes Delete Ext-Community Table
--- Represents the extended communities to be deleted for the
--- destinations.
fsMIBgp4MpeExtCommRouteDeleteExtCommTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeExtCommRouteDeleteExtCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure delete extended communities
for a given destination."
::= { fsMIBgp4MpeExtComm 2 }
fsMIBgp4MpeExtCommRouteDeleteExtCommEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeExtCommRouteDeleteExtCommEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Routes configured delete ext-communities Table Entry"
INDEX {fsMIBgp4ContextId,
fsMIBgp4mpeDeleteExtCommRtAfi,
fsMIBgp4mpeDeleteExtCommRtSafi,
fsMIBgp4mpeDeleteExtCommIpNetwork,
fsMIBgp4mpeDeleteExtCommIpPrefixLen,
fsMIBgp4mpeDeleteExtCommVal
}
::= { fsMIBgp4MpeExtCommRouteDeleteExtCommTable 1 }
FsMIBgp4MpeExtCommRouteDeleteExtCommEntry ::= SEQUENCE {
fsMIBgp4mpeDeleteExtCommRtAfi
InetAddressType,
fsMIBgp4mpeDeleteExtCommRtSafi
BgpSafi,
fsMIBgp4mpeDeleteExtCommIpNetwork
InetAddress,
fsMIBgp4mpeDeleteExtCommIpPrefixLen
Integer32,
fsMIBgp4mpeDeleteExtCommVal
OCTET STRING,
fsMIBgp4mpeDeleteExtCommRowStatus
RowStatus
}
fsMIBgp4mpeDeleteExtCommRtAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteDeleteExtCommEntry 1 }
fsMIBgp4mpeDeleteExtCommRtSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI of IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteDeleteExtCommEntry 2 }
fsMIBgp4mpeDeleteExtCommIpNetwork OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteDeleteExtCommEntry 3 }
fsMIBgp4mpeDeleteExtCommIpPrefixLen OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP prefix length for the destination"
::= { fsMIBgp4MpeExtCommRouteDeleteExtCommEntry 4 }
fsMIBgp4mpeDeleteExtCommVal OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Delete Ext-Community for the destination"
::= { fsMIBgp4MpeExtCommRouteDeleteExtCommEntry 5 }
fsMIBgp4mpeDeleteExtCommRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status to create entries into this table. This object can be set only
if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4MpeExtCommRouteDeleteExtCommEntry 6 }
-- End of Routes delete Ext-Community Table
-- Routes Ext-Community Set Status Table
-- Represents the status or local policy (can be either, addition of extended
-- communities, deletion of extended communities or both or complete
-- ommission of extended communities) for destinations.
fsMIBgp4MpeExtCommRouteExtCommSetStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeExtCommRouteExtCommSetStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure the local policy of extended communities
for a given destination."
::= {fsMIBgp4MpeExtComm 3 }
fsMIBgp4MpeExtCommRouteExtCommSetStatusEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeExtCommRouteExtCommSetStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Routes configured delete ext-communities Table Entry"
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpeExtCommSetStatusRtAfi,
fsMIBgp4mpeExtCommSetStatusRtSafi,
fsMIBgp4mpeExtCommSetStatusIpNetwork,
fsMIBgp4mpeExtCommSetStatusIpPrefixLen
}
::= { fsMIBgp4MpeExtCommRouteExtCommSetStatusTable 1 }
FsMIBgp4MpeExtCommRouteExtCommSetStatusEntry ::= SEQUENCE {
fsMIBgp4mpeExtCommSetStatusRtAfi
InetAddressType,
fsMIBgp4mpeExtCommSetStatusRtSafi
BgpSafi,
fsMIBgp4mpeExtCommSetStatusIpNetwork
InetAddress,
fsMIBgp4mpeExtCommSetStatusIpPrefixLen
Integer32,
fsMIBgp4mpeExtCommSetStatus
INTEGER,
fsMIBgp4mpeExtCommSetStatusRowStatus
RowStatus
}
fsMIBgp4mpeExtCommSetStatusRtAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteExtCommSetStatusEntry 1 }
fsMIBgp4mpeExtCommSetStatusRtSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI of IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteExtCommSetStatusEntry 2 }
fsMIBgp4mpeExtCommSetStatusIpNetwork OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the destination"
::= { fsMIBgp4MpeExtCommRouteExtCommSetStatusEntry 3 }
fsMIBgp4mpeExtCommSetStatusIpPrefixLen OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP prefix length of the destination"
::= { fsMIBgp4MpeExtCommRouteExtCommSetStatusEntry 4 }
fsMIBgp4mpeExtCommSetStatus OBJECT-TYPE
SYNTAX INTEGER {
none (1),
set (2),
setnone (3),
modify (4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Ext-Community Set status for the Route.
o none - is for read-only
o set - to send only with configured additive ext-communities
o setnone - to send without ext-communities,
o modify - to strip delete ext-communities in received extended
communities and add additive ext-communities.
This object can be set only if fsMIBgp4LocalAs is configured."
DEFVAL { 4 }
::= { fsMIBgp4MpeExtCommRouteExtCommSetStatusEntry 5 }
fsMIBgp4mpeExtCommSetStatusRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status to create entries into this table. This object can be set only
if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4MpeExtCommRouteExtCommSetStatusEntry 6 }
-- End of Routes Ext-Community set status table
-- Peer Link Bandwidth Table
-- Represents the link bandwidth for a given peer.
fsMIBgp4MpePeerLinkBwTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpePeerLinkBwEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure the link bandwidths for a given peer"
::= {fsMIBgp4MpeExtComm 4}
fsMIBgp4MpePeerLinkBwEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpePeerLinkBwEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Peer Link Bandwidth Table Entry"
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpePeerLinkType,
fsMIBgp4mpePeerLinkRemAddr
}
::= { fsMIBgp4MpePeerLinkBwTable 1 }
FsMIBgp4MpePeerLinkBwEntry ::= SEQUENCE {
fsMIBgp4mpePeerLinkType
InetAddressType,
fsMIBgp4mpePeerLinkRemAddr
InetAddress,
fsMIBgp4mpeLinkBandWidth
Unsigned32,
fsMIBgp4mpePeerLinkBwRowStatus
RowStatus
}
fsMIBgp4mpePeerLinkType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI of IP address of the Peer"
::= { fsMIBgp4MpePeerLinkBwEntry 1 }
fsMIBgp4mpePeerLinkRemAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IP address of the Peer"
::= { fsMIBgp4MpePeerLinkBwEntry 2 }
fsMIBgp4mpeLinkBandWidth OBJECT-TYPE
SYNTAX Unsigned32 (7000..4294967295)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Link Bandwidth in bytes per second.This object can be set only if
fsMIBgp4LocalAs is configured."
::= { fsMIBgp4MpePeerLinkBwEntry 3 }
fsMIBgp4mpePeerLinkBwRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row Status to create entries into this table.
This object can be set only if fsMIBgp4LocalAs is configured."
::= { fsMIBgp4MpePeerLinkBwEntry 4 }
-- End of Peer Link Table
-- MIB FOR fsMIBgp_EXTCOMM end
-- MIB FOR fsMIBgp_CABILITIES
fsMIBgp4MpeCaps OBJECT IDENTIFIER ::= { fsMIBgp 32 }
-- Supported Capabilities Table
fsMIBgp4MpeCapSupportedCapsTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeCapSupportedCapsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Supported Capabilities Table. This table contains, the capabilities
that are supported for particular peer"
::= {fsMIBgp4MpeCaps 1 }
fsMIBgp4MpeCapSupportedCapsEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeCapSupportedCapsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry contains supported Capabilites"
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpeCapPeerType,
fsMIBgp4mpeCapPeerRemoteIpAddr,
fsMIBgp4mpeSupportedCapabilityCode,
fsMIBgp4mpeSupportedCapabilityLength,
fsMIBgp4mpeSupportedCapabilityValue
}
::= { fsMIBgp4MpeCapSupportedCapsTable 1 }
FsMIBgp4MpeCapSupportedCapsEntry ::= SEQUENCE {
fsMIBgp4mpeCapPeerType
InetAddressType,
fsMIBgp4mpeCapPeerRemoteIpAddr
InetAddress,
fsMIBgp4mpeSupportedCapabilityCode
Integer32,
fsMIBgp4mpeSupportedCapabilityLength
Integer32,
fsMIBgp4mpeSupportedCapabilityValue
OCTET STRING,
fsMIBgp4mpeCapSupportedCapsRowStatus
RowStatus,
fsMIBgp4mpeCapAnnouncedStatus
INTEGER,
fsMIBgp4mpeCapReceivedStatus
INTEGER,
fsMIBgp4mpeCapNegotiatedStatus
INTEGER,
fsMIBgp4mpeCapConfiguredStatus
INTEGER
}
fsMIBgp4mpeCapPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote IP Address of Peer "
::= { fsMIBgp4MpeCapSupportedCapsEntry 1 }
fsMIBgp4mpeCapPeerRemoteIpAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE (4..16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote IP Address of Peer "
::= { fsMIBgp4MpeCapSupportedCapsEntry 2 }
fsMIBgp4mpeSupportedCapabilityCode OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"BGP-4 Capability Advertisement Capability Code that is supported for
peer."
::= { fsMIBgp4MpeCapSupportedCapsEntry 3 }
fsMIBgp4mpeSupportedCapabilityLength OBJECT-TYPE
SYNTAX Integer32 (0..251)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The length of the supported Capability data. Currently the
max size is set as 16. Update the BGP_MAX_CAP_DATA_SIZE in
inc/system.size file or BGP_DEF_MAX_CAP_DATA_SIZE in
inc/size.h to increase this MAX value."
::= { fsMIBgp4MpeCapSupportedCapsEntry 4 }
fsMIBgp4mpeSupportedCapabilityValue OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..64))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of the supported Capability"
::= { fsMIBgp4MpeCapSupportedCapsEntry 5 }
fsMIBgp4mpeCapSupportedCapsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The variable displays the status of the entry.Setting it to
'invalid' has the effect of rendering it inoperative."
::= { fsMIBgp4MpeCapSupportedCapsEntry 6 }
fsMIBgp4mpeCapAnnouncedStatus OBJECT-TYPE
SYNTAX INTEGER {
announced (1),
notAnnounced (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The variable displays the status whether the capability is
announced to the peer or not."
::= { fsMIBgp4MpeCapSupportedCapsEntry 7 }
fsMIBgp4mpeCapReceivedStatus OBJECT-TYPE
SYNTAX INTEGER {
received (1),
notReceived (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The variable displays the status whether the capability is
received from the peer or not."
::= { fsMIBgp4MpeCapSupportedCapsEntry 8 }
fsMIBgp4mpeCapNegotiatedStatus OBJECT-TYPE
SYNTAX INTEGER {
negotiated (1),
notNegotiated(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The variable displays the status whether the capability is
Negotiated to the peer or not."
::= { fsMIBgp4MpeCapSupportedCapsEntry 9 }
fsMIBgp4mpeCapConfiguredStatus OBJECT-TYPE
SYNTAX INTEGER {
configured (1),
automatic (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The variable displays the status whether the capability is
enabled by default or through configuration"
::= { fsMIBgp4MpeCapSupportedCapsEntry 10 }
-- MIB FOR Route Refresh STARTS
fsMIBgp4MpeRtRefresh OBJECT IDENTIFIER ::= {fsMIBgp 33 }
-- Route Refresh Inbound Table
fsMIBgp4MpeRtRefreshInboundTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeRtRefreshInboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Route Refresh Inbound Table"
::= { fsMIBgp4MpeRtRefresh 1 }
fsMIBgp4MpeRtRefreshInboundEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeRtRefreshInboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry corresponds to Route Refresh Inbound."
INDEX {
fsMIBgp4ContextId,
fsMIBgp4mpeRtRefreshInboundPeerType,
fsMIBgp4mpeRtRefreshInboundPeerAddr,
fsMIBgp4mpeRtRefreshInboundAfi,
fsMIBgp4mpeRtRefreshInboundSafi
}
::= { fsMIBgp4MpeRtRefreshInboundTable 1 }
FsMIBgp4MpeRtRefreshInboundEntry ::= SEQUENCE {
fsMIBgp4mpeRtRefreshInboundPeerType
InetAddressType,
fsMIBgp4mpeRtRefreshInboundPeerAddr
InetAddress,
fsMIBgp4mpeRtRefreshInboundAfi
InetAddressType,
fsMIBgp4mpeRtRefreshInboundSafi
BgpSafi,
fsMIBgp4mpeRtRefreshInboundRequest
INTEGER,
fsMIBgp4mpeRtRefreshInboundPrefixFilter
INTEGER
}
fsMIBgp4mpeRtRefreshInboundPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address Family Identifier of the peer remote address"
::= { fsMIBgp4MpeRtRefreshInboundEntry 1 }
fsMIBgp4mpeRtRefreshInboundPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the peeri for which the Route Refresh request has to
be issued."
::= { fsMIBgp4MpeRtRefreshInboundEntry 2 }
fsMIBgp4mpeRtRefreshInboundAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The AFI for which the Route-Refresh message is to be sent"
::= { fsMIBgp4MpeRtRefreshInboundEntry 3 }
fsMIBgp4mpeRtRefreshInboundSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SAFI for which the Route-Refresh message is to be sent"
::= { fsMIBgp4MpeRtRefreshInboundEntry 4 }
fsMIBgp4mpeRtRefreshInboundRequest OBJECT-TYPE
SYNTAX INTEGER
{
true (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object triggers the sending of the Route Refresh message
to the peer. This object will be cleared once the Route Refresh message
is sent to the peer. Route-Refresh message support is a default feature
If not negotiated via capability negotiation, inbound soft-reconfig is
internally done on setting this object."
::= { fsMIBgp4MpeRtRefreshInboundEntry 5 }
fsMIBgp4mpeRtRefreshInboundPrefixFilter OBJECT-TYPE
SYNTAX INTEGER
{
true (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object triggers the sending of the ORF entris in the
Route Refresh message to the peer. This object will be cleared once
the ORF message is sent to the peer. Get operation of this object will
always return zero."
::= { fsMIBgp4MpeRtRefreshInboundEntry 6 }
--
-- Route Refresh Statistics Table
--
fsMIBgp4MpeRtRefreshStatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeRtRefreshStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Route Refresh Statistics Table"
::= { fsMIBgp4MpeRtRefresh 2 }
fsMIBgp4MpeRtRefreshStatisticsEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeRtRefreshStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry gives the statistics of Route Refresh."
INDEX {
fsMIBgp4ContextId,
fsMIBgp4mpeRtRefreshStatisticsPeerType,
fsMIBgp4mpeRtRefreshStatisticsPeerAddr,
fsMIBgp4mpeRtRefreshStatisticsAfi,
fsMIBgp4mpeRtRefreshStatisticsSafi
}
::= { fsMIBgp4MpeRtRefreshStatisticsTable 1 }
FsMIBgp4MpeRtRefreshStatisticsEntry ::= SEQUENCE {
fsMIBgp4mpeRtRefreshStatisticsPeerType
InetAddressType,
fsMIBgp4mpeRtRefreshStatisticsPeerAddr
InetAddress,
fsMIBgp4mpeRtRefreshStatisticsAfi
InetAddressType,
fsMIBgp4mpeRtRefreshStatisticsSafi
BgpSafi,
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgSentCntr
Counter32,
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgTxErrCntr
Counter32,
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgRcvdCntr
Counter32,
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgInvalidCntr
Counter32
}
fsMIBgp4mpeRtRefreshStatisticsPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address Family Identifier of the peer remote address."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 1 }
fsMIBgp4mpeRtRefreshStatisticsPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the peer for which the Route Refresh Statistics has
to be read."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 2 }
fsMIBgp4mpeRtRefreshStatisticsAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI for for which the Route Refresh Statistics has
to be read."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 3 }
fsMIBgp4mpeRtRefreshStatisticsSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI for for which the Route Refresh Statistics has
to be read."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 4 }
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgSentCntr OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of Route Refresh messages sent to the peer."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 5 }
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgTxErrCntr OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of Route Refresh messages that could not be
transmitted to the peer."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 6 }
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgRcvdCntr OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of Route Refresh messages received from the peer."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 7 }
fsMIBgp4mpeRtRefreshStatisticsRtRefMsgInvalidCntr OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The number of invalid Route Refresh messages received from the peer."
::= { fsMIBgp4MpeRtRefreshStatisticsEntry 8 }
-- MIB FOR OutBound Soft-Reconfig STARTS
fsMIBgp4MpeSoftReconfigOut OBJECT IDENTIFIER ::= { fsMIBgp 34 }
fsMIBgp4MpeSoftReconfigOutboundTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpeSoftReconfigOutboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Soft Reconfig outbound Table"
::= { fsMIBgp4MpeSoftReconfigOut 1 }
fsMIBgp4MpeSoftReconfigOutboundEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpeSoftReconfigOutboundEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry corresponds to Soft Reconfig outbound."
INDEX { fsMIBgp4ContextId,
fsMIBgp4mpeSoftReconfigOutboundPeerType,
fsMIBgp4mpeSoftReconfigOutboundPeerAddr,
fsMIBgp4mpeSoftReconfigOutboundAfi,
fsMIBgp4mpeSoftReconfigOutboundSafi
}
::= { fsMIBgp4MpeSoftReconfigOutboundTable 1 }
FsMIBgp4MpeSoftReconfigOutboundEntry ::= SEQUENCE {
fsMIBgp4mpeSoftReconfigOutboundPeerType
InetAddressType,
fsMIBgp4mpeSoftReconfigOutboundPeerAddr
InetAddress,
fsMIBgp4mpeSoftReconfigOutboundAfi
InetAddressType,
fsMIBgp4mpeSoftReconfigOutboundSafi
BgpSafi,
fsMIBgp4mpeSoftReconfigOutboundRequest
INTEGER
}
fsMIBgp4mpeSoftReconfigOutboundPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address Family Identifier of the peer remote address"
::= { fsMIBgp4MpeSoftReconfigOutboundEntry 1 }
fsMIBgp4mpeSoftReconfigOutboundPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the peer for which the outbound soft-reconfig has to
be performed."
::= { fsMIBgp4MpeSoftReconfigOutboundEntry 2 }
fsMIBgp4mpeSoftReconfigOutboundAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"AFI for which the outbound soft-reconfig has to
be performed."
::= { fsMIBgp4MpeSoftReconfigOutboundEntry 3 }
fsMIBgp4mpeSoftReconfigOutboundSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"SAFI for which the outbound soft-reconfig has to
be performed."
::= { fsMIBgp4MpeSoftReconfigOutboundEntry 4 }
fsMIBgp4mpeSoftReconfigOutboundRequest OBJECT-TYPE
SYNTAX INTEGER
{
true (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object triggers the outbound soft-reconfig process for the peer. This object value is cleared once the soft-reconfig process is
completed."
::= { fsMIBgp4MpeSoftReconfigOutboundEntry 5 }
--
-- Prefix counter table
--
fsMIBgp4MpePrefixCountersTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4MpePrefixCountersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Additional per-peer, per AFI/SAFI counters for prefixes"
::= { fsMIBgp 35 }
fsMIBgp4MpePrefixCountersEntry OBJECT-TYPE
SYNTAX FsMIBgp4MpePrefixCountersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing information about a bgp-peer's prefix
counters."
INDEX {
fsMIBgp4ContextId,
fsMIBgp4MpePeerRemoteAddrType,
fsMIBgp4MpePeerRemoteAddr,
fsMIBgp4MpePrefixCountersAfi,
fsMIBgp4MpePrefixCountersSafi
}
::= { fsMIBgp4MpePrefixCountersTable 1 }
FsMIBgp4MpePrefixCountersEntry ::= SEQUENCE {
fsMIBgp4MpePeerRemoteAddrType
InetAddressType,
fsMIBgp4MpePeerRemoteAddr
InetAddress,
fsMIBgp4MpePrefixCountersAfi
InetAddressType,
fsMIBgp4MpePrefixCountersSafi
BgpSafi,
fsMIBgp4MpePrefixCountersPrefixesReceived
Counter32,
fsMIBgp4MpePrefixCountersPrefixesSent
Counter32,
fsMIBgp4MpePrefixCountersWithdrawsReceived
Counter32,
fsMIBgp4MpePrefixCountersWithdrawsSent
Counter32,
fsMIBgp4MpePrefixCountersInPrefixes
Gauge32,
fsMIBgp4MpePrefixCountersInPrefixesAccepted
Gauge32,
fsMIBgp4MpePrefixCountersInPrefixesRejected
Gauge32,
fsMIBgp4MpePrefixCountersOutPrefixes
Gauge32
}
fsMIBgp4MpePeerRemoteAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the remote address of peer."
::= { fsMIBgp4MpePrefixCountersEntry 1 }
fsMIBgp4MpePeerRemoteAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The remote address of the peer."
::= { fsMIBgp4MpePrefixCountersEntry 2 }
fsMIBgp4MpePrefixCountersAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The AFI index of the per-peer, per prefix counters"
::= { fsMIBgp4MpePrefixCountersEntry 3 }
fsMIBgp4MpePrefixCountersSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SAFI index of the per-peer, per prefix counters"
::= { fsMIBgp4MpePrefixCountersEntry 4 }
fsMIBgp4MpePrefixCountersPrefixesReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of discrete prefixes received from this peer. The
value in fsMIBgp4MpePrefixCountersPrefixesReceived will be greater
than or equal to what is in fsMIBgp4MpePrefixCountersInPrefixes,
since it will reflect prefixes received from this peer which
may have been subsquently withdrawn, and hence will no longer
be stored in the Adj-Ribs-In for that peer."
::= { fsMIBgp4MpePrefixCountersEntry 5 }
fsMIBgp4MpePrefixCountersPrefixesSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of prefixes which the local BGP speaker
has announced to this peer. The value for
fsMIBgp4MpePrefixCountersPrefixesSent will be greater than or equal to
fsMIBgp4MpePrefixCountersOutPrefixes, since it reflects prefixes
which have been subsequently withdrawn after their announcement
(assuming any such withdrawn prefixes exist)."
::= { fsMIBgp4MpePrefixCountersEntry 6 }
fsMIBgp4MpePrefixCountersWithdrawsReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of prefixes withdrawn by this peer. Specifically,
this is the total number of withdrawn-routes which have
been received in UPDATE messages from this peer."
::= { fsMIBgp4MpePrefixCountersEntry 7 }
fsMIBgp4MpePrefixCountersWithdrawsSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of prefixes which have been reported as
withdrawn by the local BGP speaker to the peer in
locally generated UPDATE messages to the peer."
::= { fsMIBgp4MpePrefixCountersEntry 8 }
fsMIBgp4MpePrefixCountersInPrefixes OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of prefixes received from a peer and are
stored in the Adj-Ribs-In for that peer."
-- jmh - note that we're allowing stuff to be discarded
::= { fsMIBgp4MpePrefixCountersEntry 9 }
fsMIBgp4MpePrefixCountersInPrefixesAccepted OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of prefixes for a peer that are installed
in the Adj-Ribs-In and are eligible to become active
in the Loc-Rib."
::= { fsMIBgp4MpePrefixCountersEntry 10 }
fsMIBgp4MpePrefixCountersInPrefixesRejected OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of prefixes for a peer that are installed
in the Adj-Ribs-In and are NOT eligible to become active
in the Loc-Rib."
::= { fsMIBgp4MpePrefixCountersEntry 11 }
fsMIBgp4MpePrefixCountersOutPrefixes OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of prefixes for a peer that are installed
in that peer's Adj-Ribs-Out."
::= { fsMIBgp4MpePrefixCountersEntry 12 }
--**************************************************************************
-- FILTERING OBJECT DEFINITION BEGIN
fsMIBgp4DistInOutRouteMap OBJECT IDENTIFIER ::= { fsMIBgp 36 }
fsMIBgp4DistInOutRouteMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4DistInOutRouteMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table describing the configuration of filtering for route map."
::= { fsMIBgp4DistInOutRouteMap 1 }
fsMIBgp4DistInOutRouteMapEntry OBJECT-TYPE
SYNTAX FsMIBgp4DistInOutRouteMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the filtering configuration of single entry."
INDEX {fsMIBgp4ContextId,
fsMIBgp4DistInOutRouteMapName,
fsMIBgp4DistInOutRouteMapType}
::= { fsMIBgp4DistInOutRouteMapTable 1 }
FsMIBgp4DistInOutRouteMapEntry ::= SEQUENCE {
fsMIBgp4DistInOutRouteMapName DisplayString,
fsMIBgp4DistInOutRouteMapType Integer32,
fsMIBgp4DistInOutRouteMapValue Integer32,
fsMIBgp4DistInOutRouteMapRowStatus RowStatus
}
fsMIBgp4DistInOutRouteMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Route map name."
::= { fsMIBgp4DistInOutRouteMapEntry 1 }
fsMIBgp4DistInOutRouteMapType OBJECT-TYPE
SYNTAX Integer32(1..3)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Type of route map to indicate the route map is for
distribute in or for distribute out or for distance.
1 - distance
2 - distribute in
3 - distribute out"
::= { fsMIBgp4DistInOutRouteMapEntry 2 }
fsMIBgp4DistInOutRouteMapValue OBJECT-TYPE
SYNTAX Integer32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Distance value ( this will be unused for distribute list )"
::= { fsMIBgp4DistInOutRouteMapEntry 3 }
fsMIBgp4DistInOutRouteMapRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table."
::= { fsMIBgp4DistInOutRouteMapEntry 4 }
-- FILTERING OBJECT DEFINITION END
-- TRAP objects
fsMIBgp4Notification OBJECT IDENTIFIER ::= { fsMIBgp 37 }
fsMIBgp4Trap OBJECT IDENTIFIER ::= { fsMIBgp4Notification 0}
fsMIBgp4Objects OBJECT IDENTIFIER ::= { fsMIBgp4Notification 1}
fsMIBgp4TrapContextId OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object refers to the BGP Context in
which the route addition failed."
::= { fsMIBgp4Objects 1 }
fsMIBgp4TrapRouteAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object refers to the addresstype of BGP Route.
Used for sending BGP route addition failure Traps."
::= { fsMIBgp4Objects 2 }
fsMIBgp4TrapRoutePrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object refers to BGP Route.
Used for sending BGP route addition failure Traps."
::= { fsMIBgp4Objects 3 }
fsMIBgp4NextHop OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object refers to nexthop of bgp Route.
Used for sending BGP route addition failure Traps."
::= { fsMIBgp4Objects 4}
fsMIBgp4TrapPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object refers to the addresstype of bgp peer address.
Used for sending BGP route addition failure Traps."
::= { fsMIBgp4Objects 5 }
fsMIBgp4TrapPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object refers to the address of bgp peer from which route is learned.
Used for sending BGP route addition failure Traps."
::= { fsMIBgp4Objects 6 }
fsMIBgp4RestartStatusChange NOTIFICATION-TYPE
OBJECTS {
fsMIBgp4Identifier,
fsMIBgp4RestartStatus,
fsMIBgp4GRRestartTimeInterval,
fsMIBgp4RestartExitReason
}
STATUS current
DESCRIPTION
"A fsMIBgp4RestartStatusChange trap signifies that there has
been a change in the graceful restart state for the router.
This trap should be generated when the router restart status changes."
::= {fsMIBgp4Trap 1}
fsMIBgp4RouteAddRTMFailure NOTIFICATION-TYPE
OBJECTS {
fsMIBgp4TrapContextId,
fsMIBgp4Identifier,
fsMIBgp4TrapRouteAddressType,
fsMIBgp4TrapRoutePrefix,
fsMIBgp4TrapPeerAddrType,
fsMIBgp4TrapPeerAddr,
fsMIBgp4mpebgp4PathAttrNextHop
}
STATUS current
DESCRIPTION
"A fsMIBGP4RouteAddRTMFailure trap signifies failure in adding a route to RTM from
BGP."
::= {fsMIBgp4Trap 3}
-- ROUTE-MAP ON NEIGHBOUR
fsMIBgp4NeighborRouteMap OBJECT IDENTIFIER ::= { fsMIBgp 38 }
fsMIBgp4NeighborRouteMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4NeighborRouteMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table describing the configuration of route map on a neighbour."
::= { fsMIBgp4NeighborRouteMap 1 }
fsMIBgp4NeighborRouteMapEntry OBJECT-TYPE
SYNTAX FsMIBgp4NeighborRouteMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the routemap configuration of single entry."
INDEX {fsMIBgp4ContextId,
fsMIBgp4NeighborRouteMapPeerAddrType,
fsMIBgp4NeighborRouteMapPeer,
fsMIBgp4NeighborRouteMapDirection}
::= { fsMIBgp4NeighborRouteMapTable 1 }
FsMIBgp4NeighborRouteMapEntry ::= SEQUENCE {
fsMIBgp4NeighborRouteMapPeerAddrType InetAddressType,
fsMIBgp4NeighborRouteMapPeer InetAddress,
fsMIBgp4NeighborRouteMapDirection INTEGER,
fsMIBgp4NeighborRouteMapName DisplayString,
fsMIBgp4NeighborRouteMapRowStatus RowStatus
}
fsMIBgp4NeighborRouteMapPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Adress type of the Neighbor."
::= { fsMIBgp4NeighborRouteMapEntry 1 }
fsMIBgp4NeighborRouteMapPeer OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IpAddress of the Neighbor."
::= { fsMIBgp4NeighborRouteMapEntry 2 }
fsMIBgp4NeighborRouteMapDirection OBJECT-TYPE
SYNTAX INTEGER{ in(1) ,
out(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Direction of route map to indicate the route map is for in or out.
In direction routemap is to apply the routemap rules for incoming routes from
the peer.Out direction routemap is to apply the routemap for on the
advertising routes to the peer.
1 - in
2 - out"
::= { fsMIBgp4NeighborRouteMapEntry 3 }
fsMIBgp4NeighborRouteMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..20))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Route map name."
::= { fsMIBgp4NeighborRouteMapEntry 4 }
fsMIBgp4NeighborRouteMapRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table."
::= { fsMIBgp4NeighborRouteMapEntry 5 }
-- BGP Peer Group Table
fsMIBgp4PeerGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4PeerGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table for configuring the bgp peer groups. Configuring
a property for the peer group copies it to all the peers
present in the peer group."
::= { fsMIBgp 39 }
fsMIBgp4PeerGroupEntry OBJECT-TYPE
SYNTAX FsMIBgp4PeerGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry describing the bgp peer group."
INDEX { fsMIBgp4ContextId,
fsMIBgp4PeerGroupName }
::= { fsMIBgp4PeerGroupTable 1 }
FsMIBgp4PeerGroupEntry ::= SEQUENCE {
fsMIBgp4PeerGroupName DisplayString,
fsMIBgp4PeerGroupAddrType InetAddressType,
fsMIBgp4PeerGroupRemoteAs Unsigned32,
fsMIBgp4PeerGroupHoldTimeConfigured Integer32,
fsMIBgp4PeerGroupKeepAliveConfigured Integer32,
fsMIBgp4PeerGroupConnectRetryInterval Integer32,
fsMIBgp4PeerGroupMinASOriginInterval Integer32,
fsMIBgp4PeerGroupMinRouteAdvInterval Integer32,
fsMIBgp4PeerGroupAllowAutomaticStart INTEGER,
fsMIBgp4PeerGroupAllowAutomaticStop INTEGER,
fsMIBgp4PeerGroupIdleHoldTimeConfigured Integer32,
fsMIBgp4PeerGroupDampPeerOscillations INTEGER,
fsMIBgp4PeerGroupDelayOpen INTEGER,
fsMIBgp4PeerGroupDelayOpenTimeConfigured Integer32,
fsMIBgp4PeerGroupPrefixUpperLimit Integer32,
fsMIBgp4PeerGroupTcpConnectRetryCnt Integer32,
fsMIBgp4PeerGroupEBGPMultiHop INTEGER,
fsMIBgp4PeerGroupEBGPHopLimit Integer32,
fsMIBgp4PeerGroupNextHopSelf INTEGER,
fsMIBgp4PeerGroupRflClient INTEGER,
fsMIBgp4PeerGroupTcpSendBufSize Integer32,
fsMIBgp4PeerGroupTcpRcvBufSize Integer32,
fsMIBgp4PeerGroupCommSendStatus INTEGER,
fsMIBgp4PeerGroupECommSendStatus INTEGER,
fsMIBgp4PeerGroupPassive INTEGER,
fsMIBgp4PeerGroupDefaultOriginate INTEGER,
fsMIBgp4PeerGroupActivateMPCapability INTEGER,
fsMIBgp4PeerGroupDeactivateMPCapability INTEGER,
fsMIBgp4PeerGroupRouteMapNameIn DisplayString,
fsMIBgp4PeerGroupRouteMapNameOut DisplayString,
fsMIBgp4PeerGroupStatus RowStatus,
fsMIBgp4PeerGroupIpPrefixNameIn DisplayString,
fsMIBgp4PeerGroupIpPrefixNameOut DisplayString,
fsMIBgp4PeerGroupOrfType Unsigned32,
fsMIBgp4PeerGroupOrfCapMode INTEGER,
fsMIBgp4PeerGroupOrfRequest INTEGER
}
fsMIBgp4PeerGroupName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The group name for this peer group entry."
::= { fsMIBgp4PeerGroupEntry 1 }
fsMIBgp4PeerGroupAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the peers added to this peer group."
::= { fsMIBgp4PeerGroupEntry 2 }
fsMIBgp4PeerGroupRemoteAs OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The remote autonomous system number for this peer group."
::= { fsMIBgp4PeerGroupEntry 3 }
fsMIBgp4PeerGroupHoldTimeConfigured OBJECT-TYPE
SYNTAX Integer32 ( 0 | 3..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval (in seconds) for the Hold Time configured for this
BGP speaker with all the peers configured for this group.
This value is placed in an OPEN message sent to the peers
by this BGP speaker. This value must not be less than three seconds
if it is not zero (0). If it is zero (0), the Hold Time is NOT to be
established with the peer.
The suggested value for this timer is 90 seconds."
::= { fsMIBgp4PeerGroupEntry 4 }
fsMIBgp4PeerGroupKeepAliveConfigured OBJECT-TYPE
SYNTAX Integer32 ( 0 | 1..21845 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval (in seconds) for the KeepAlive timer configured for this
BGP speaker with all the peers configured in this group. The value
of this object will only determine the KEEPALIVE messages frequency
relative to the value specified in fsMIBgp4PeerGroupCfgHoldTime.
A reasonable maximum value for this timer would be one third of that
of fsMIBgp4PeerGroupCfgHoldTime. If the value of this object is zero (0),
no periodical KEEPALIVE messages are sent to the peers after the
BGP connection is established.
The suggested value for this timer is 30 seconds."
::= { fsMIBgp4PeerGroupEntry 5 }
fsMIBgp4PeerGroupConnectRetryInterval OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval in seconds for the ConnectRetry timer for the peers
in this group. The suggested value for this timer is 120 seconds."
::= { fsMIBgp4PeerGroupEntry 6 }
fsMIBgp4PeerGroupMinASOriginInterval OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval (in seconds) for the MinASOriginationInterval
timer for all peers configured in this group.
The suggested value for this timer is 15 seconds."
::= { fsMIBgp4PeerGroupEntry 7 }
fsMIBgp4PeerGroupMinRouteAdvInterval OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time interval (in seconds) for the MinRouteAdvertisementInterval timer.
The suggested value for this timer is 30 seconds for EBGP connections
and 5 seconds for IBGP connections."
::= { fsMIBgp4PeerGroupEntry 8 }
fsMIBgp4PeerGroupAllowAutomaticStart OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This MIB object specifies whether BGP session with the peers in the
peer group can be started automatically. This object when set to
'disabled', requires manual start for initiating BGP session with the peer via
MIB object 'fsMIBgp4PeerGroupAdminStatus'. When set to 'enabled',
the peer session can be automatically started in the IDLE state,
after a BGP Peer session is brought down either by Autostop or via
reception of invalid BGP message. The BGP session will be automatically
started after an interval specified by
'fsMIBgp4PeerGroupIdleHoldTimeConfigured'. If
fsMIBgp4PeerGroupDampPeerOscillations is enabled, then automaticStart will not
occur if peer is damped."
DEFVAL { disable }
::= { fsMIBgp4PeerGroupEntry 9 }
fsMIBgp4PeerGroupAllowAutomaticStop OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This MIB object specifies whether BGP session with the peers in the
peer group need to be automatically stopped after a TCP connect-retry
count value specified by 'fsMIBgp4PeerGroupTcpConnectRetryCnt'.
The resources allocated for the BGP peers are released and it
continues to remain in IDLE state. After an automatic stop,
the Peer connection needs to be re-intiated manually by the
administrator. When AutomaticStop is disabled, the connect retry
count value is set to 0."
DEFVAL { disable }
::= { fsMIBgp4PeerGroupEntry 10 }
fsMIBgp4PeerGroupIdleHoldTimeConfigured OBJECT-TYPE
SYNTAX Integer32 ( 1..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IdleHoldTime specifies the length of time the BGP peers in this
peer group is held in Idle state prior to allowing the next
automatic restart. The IdleHoldTime is configured only when the
fsMIBgp4PeerGroupAllowAutomaticStart is Enabled or when the
fsMIBgp4PeerGroupDampPeerOscillations is Enabled. The configurable value
differs based on the two options that are enabled.The Suggested default
value is 60 secs for automatic start. After each dampening, the value
of the IdleHoldTime is doubled consecutively."
DEFVAL { 60 }
::= { fsMIBgp4PeerGroupEntry 11 }
fsMIBgp4PeerGroupDampPeerOscillations OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DampPeerOscillations option specifies that the implementation
engages additional logic to damp the oscillations of BGP peers in
the face of series of automatic start and automatic stop operations
in the IDLE state.The DampPeerOscillations option indicates that the
BGP connection is using logic that damps BGP peer oscillations in
states other than 'established' state."
DEFVAL { disable }
::= { fsMIBgp4PeerGroupEntry 12 }
fsMIBgp4PeerGroupDelayOpen OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This MIB object allows configuration option to enable/disable delay
in sending of OPEN messages to the BGP peers for a specific time period
(DelayOpenTime). The delay allows the remote BGP Peers to send the first
OPEN message."
DEFVAL { disable }
::= { fsMIBgp4PeerGroupEntry 13 }
fsMIBgp4PeerGroupDelayOpenTimeConfigured OBJECT-TYPE
SYNTAX Integer32 ( 0..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DelayOpen time specifies the amount of time the BGP Peers should
delay in sending the OPEN message to the remote peers. If the
fsMIBgp4PeerGroupDelayOpen option is enabled, the DelayOpen time can be
configured. The default value is kept as 0 secs, which implies that
the BGP Peers can send an OPEN message without any delay to its
neighbor."
DEFVAL { 0 }
::= { fsMIBgp4PeerGroupEntry 14 }
fsMIBgp4PeerGroupPrefixUpperLimit OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"BGP speaker imposes a locally-configured, upper bound on the number of
address prefixes the speaker is willing to accept from a neighbor. The
default value is calculated as the following:
fsMIBgp4MaxNoofRoutes / fsMIBgp4MaxPeerEntry
Administrator can configure a value less than the default value at
runtime. Prefixes exceeding the PrefixUpperLimit will not be processed
by the system."
DEFVAL { 100 }
::= { fsMIBgp4PeerGroupEntry 15 }
fsMIBgp4PeerGroupTcpConnectRetryCnt OBJECT-TYPE
SYNTAX Integer32 (1..50)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This counter denotes the Maximum number of times the BGP Peers have
tried to issue a TCP-Connect with its neighboring peers.
The default value for the counter is set as 5."
DEFVAL { 5 }
::= { fsMIBgp4PeerGroupEntry 16 }
fsMIBgp4PeerGroupEBGPMultiHop OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects enables the BGP4 Speaker to accept or attempt
connections to external peers residing on network that are not directly
connected. By default, only directly connected EBGP peers are allowed.
The configuration of this object has effect only when the peers added to
this peer group are of EBGP type."
::= { fsMIBgp4PeerGroupEntry 17 }
fsMIBgp4PeerGroupEBGPHopLimit OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects enables the BGP4 Speaker to accept or attempt
connections to external peers residing on network that are not directly
connected and seperated by a maximum hop limit as configured by this
object. The configuration of this object has effect only when the peers added to
this peer group are of EBGP type."
::= { fsMIBgp4PeerGroupEntry 18 }
fsMIBgp4PeerGroupNextHopSelf OBJECT-TYPE
SYNTAX INTEGER
{
automatic(1),
self(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies how the next hop attribute sent in the update
messages to the peers in this peer group. When the object takes the
value of self,the next Hop attribute will always be the sender Local
Address else the next hop will be generated based on the IP address of
the destination and the present next hop in the route information."
DEFVAL { automatic }
::= { fsMIBgp4PeerGroupEntry 19 }
fsMIBgp4PeerGroupRflClient OBJECT-TYPE
SYNTAX INTEGER
{
nonClient (1),
client (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the peers in this peer group are
Client peers or Non-Client peers. By default, the peers are
created as Non-Client Peer. "
DEFVAL { nonClient }
::= { fsMIBgp4PeerGroupEntry 20 }
fsMIBgp4PeerGroupTcpSendBufSize OBJECT-TYPE
SYNTAX Integer32 (4096..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the tcp window size on the sender side
for all the peers in this peer group."
DEFVAL { 65536 }
::= { fsMIBgp4PeerGroupEntry 21 }
fsMIBgp4PeerGroupTcpRcvBufSize OBJECT-TYPE
SYNTAX Integer32 (4096..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the tcp window size on the receiver side
for all the peers in this peer group."
DEFVAL { 65536 }
::= { fsMIBgp4PeerGroupEntry 22 }
fsMIBgp4PeerGroupCommSendStatus OBJECT-TYPE
SYNTAX INTEGER
{
none (1),
send (2),
donotsend (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Community Send status for the peers in this peer group.
o none - is for read-only
o send - send communities to this peer
o donotsend - do not send communities to this peer."
DEFVAL { send }
::= { fsMIBgp4PeerGroupEntry 23 }
fsMIBgp4PeerGroupECommSendStatus OBJECT-TYPE
SYNTAX INTEGER
{
none (1),
send (2),
donotsend (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Extended Community Send status for the peers in this peer group.
o none - is for read-only
o send - send extended communities to this peer
o donotsend - do not send extended communities to this peer."
DEFVAL { send }
::= { fsMIBgp4PeerGroupEntry 24 }
fsMIBgp4PeerGroupPassive OBJECT-TYPE
SYNTAX INTEGER
{
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to set the peers in this group to be active,
that means the speaker will not initiate the session with the peers
instead it waits for the remote peers to initiate the session"
::= { fsMIBgp4PeerGroupEntry 25 }
fsMIBgp4PeerGroupDefaultOriginate OBJECT-TYPE
SYNTAX INTEGER
{
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable/disable the advertisement
of the default route to all the peers in this peer group.
This object overrides the global default route configuration
(fsMIBgp4DefaultOriginate) and always send a default
route to the peer with self next-hop. This advertisement occurs
irrespective of the presence of default route in FDB. This object can
be set only if the fsMIBgp4LocalAs is set."
DEFVAL { disable }
::= { fsMIBgp4PeerGroupEntry 26 }
fsMIBgp4PeerGroupActivateMPCapability OBJECT-TYPE
SYNTAX INTEGER
{
ipv4unicast(1),
ipv6unicast(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is set to activate the corresponding MP Capability.
If any of MP Capability is activated, then this capability should
be negotiated while establishing session with the peers in this group.
Any get on this object will return only ZERO."
::= { fsMIBgp4PeerGroupEntry 27 }
fsMIBgp4PeerGroupDeactivateMPCapability OBJECT-TYPE
SYNTAX INTEGER
{
ipv4unicast(1),
ipv6unicast(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is set to deactivate the corresponding MP Capability.
If any of MP Capability is deactivated, then this capability should
not be negotiated while establishing session with the peers in this group.
Any get on this object will return only ZERO."
::= { fsMIBgp4PeerGroupEntry 28 }
fsMIBgp4PeerGroupRouteMapNameIn OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the in routemap for this peer group entry."
::= { fsMIBgp4PeerGroupEntry 29 }
fsMIBgp4PeerGroupRouteMapNameOut OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the out routemap for this peer group entry."
::= { fsMIBgp4PeerGroupEntry 30 }
fsMIBgp4PeerGroupStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to create the peer group or delete the group."
::= { fsMIBgp4PeerGroupEntry 31 }
fsMIBgp4PeerGroupIpPrefixNameIn OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the IP Prefix list name in IN direction for this peer group entry."
::= { fsMIBgp4PeerGroupEntry 32 }
fsMIBgp4PeerGroupIpPrefixNameOut OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the IP Prefix list name in OUT direction for this peer group entry."
::= { fsMIBgp4PeerGroupEntry 33 }
fsMIBgp4PeerGroupOrfType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the ORF type supported for this peer group entry.
This object should be configure before enabling the ORF modes fsMIBgp4PeerGroupOrfCapMode
Now the Address Prefix ORF type (value 64) is only supported"
::= { fsMIBgp4PeerGroupEntry 34 }
fsMIBgp4PeerGroupOrfCapMode OBJECT-TYPE
SYNTAX INTEGER {
disable (0),
receive (1),
send (2),
both (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to configure the ORF Capability mode supported for this peer group entry.
If it is set to ZERO, then the both ORF modes will be disabled"
::= { fsMIBgp4PeerGroupEntry 35 }
fsMIBgp4PeerGroupOrfRequest OBJECT-TYPE
SYNTAX INTEGER {
true (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is to trigger the ORF messages to the peers associated with this peer group entry.
Once the ORF messages are transmitted, this object will be cleared.
Get operation of this object wil1 always return ZERO."
::= { fsMIBgp4PeerGroupEntry 36 }
fsMIBgp4PeerGroupListTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4PeerGroupListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table for adding/removing the bgp peers to a peer group."
::= { fsMIBgp 40 }
fsMIBgp4PeerGroupListEntry OBJECT-TYPE
SYNTAX FsMIBgp4PeerGroupListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry describing the bgp peer group list."
INDEX { fsMIBgp4ContextId, fsMIBgp4PeerGroupName, fsMIBgp4PeerAddrType, fsMIBgp4PeerAddress }
::= { fsMIBgp4PeerGroupListTable 1 }
FsMIBgp4PeerGroupListEntry ::= SEQUENCE {
fsMIBgp4PeerAddrType InetAddressType,
fsMIBgp4PeerAddress InetAddress,
fsMIBgp4PeerAddStatus INTEGER
}
fsMIBgp4PeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the address type of the BGP peer entry
added to this peer group entry"
::= { fsMIBgp4PeerGroupListEntry 1 }
fsMIBgp4PeerAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the remote address of the BGP peer entry
added to this peer group entry"
::= { fsMIBgp4PeerGroupListEntry 2 }
fsMIBgp4PeerAddStatus OBJECT-TYPE
SYNTAX INTEGER
{
add(1),
delete(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to add or remove the bgp peer specified through
fsMIBgp4PeerAddress to this bgp peer group entry."
::= { fsMIBgp4PeerGroupListEntry 3 }
fsMIBgp4RestartReason OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
softwareRestart (1),
swReloadUpgrade (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The reason for restart for the Restarting Router.
Options include: unknown,softwarerestart,swreloadupgrade,
switchtoredundant. This object is persistent and when written
the entity SHOULD save the change to non-volatile storage."
DEFVAL {softwareRestart}
::= { fsMIBgp 41 }
-- MIB for TCP AO Authentication starts
fsMIBgp4TCPMKTAuth OBJECT IDENTIFIER ::= {fsMIBgp 42}
-- TCP MKT(Master Key Tuple) Authentication Table
fsMIBgp4TCPMKTAuthTable OBJECT-TYPE
SYNTAX SEQUENCE OF Fsbgp4TCPMKTAuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"TCP MKT Authentication Table, used for configuring MKT for TCP-AO
authentication, supported algorithms HMAC-SHA-1 and AES-128-CMAC"
::= { fsMIBgp4TCPMKTAuth 1 }
fsMIBgp4TCPMKTAuthEntry OBJECT-TYPE
SYNTAX Fsbgp4TCPMKTAuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry corresponds to the TCP MKT parameters"
INDEX {
fsMIBgp4ContextId,
fsMIBgp4TCPMKTAuthKeyId
}
::= { fsMIBgp4TCPMKTAuthTable 1 }
Fsbgp4TCPMKTAuthEntry ::= SEQUENCE {
fsMIBgp4TCPMKTAuthKeyId
Integer32,
fsMIBgp4TCPMKTAuthRecvKeyId
Integer32,
fsMIBgp4TCPMKTAuthMasterKey
OCTET STRING,
fsMIBgp4TCPMKTAuthAlgo
INTEGER,
fsMIBgp4TCPMKTAuthTcpOptExc
TruthValue,
fsMIBgp4TCPMKTAuthRowStatus
RowStatus
}
fsMIBgp4TCPMKTAuthKeyId OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Send KeyID of the MKT. This object value is used to fill the key-id
field in the TCP-AO option in the TCP header"
::= { fsMIBgp4TCPMKTAuthEntry 1 }
fsMIBgp4TCPMKTAuthRecvKeyId OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Receive Key-id of the MKT. The MKT that is ready at the sender to
be used to authenticate received segments is indicated to the
peer by filling the receive key id of the MKT in the RNExtKeyId
field of the TCP-AO option in TCP header."
::= { fsMIBgp4TCPMKTAuthEntry 2 }
fsMIBgp4TCPMKTAuthMasterKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..80))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Master Key corresponding to the MKT"
::= { fsMIBgp4TCPMKTAuthEntry 3 }
fsMIBgp4TCPMKTAuthAlgo OBJECT-TYPE
SYNTAX INTEGER
{
hmacSha1(1),
aes128Cmac(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Algorithm used for TCP-AO MAC or KDF calculation, allowed
algorithms are HMAC-SHA-1 & AES-128-CMAC,
default value is HMAC-SHA-1"
DEFVAL { hmacSha1 }
::= { fsMIBgp4TCPMKTAuthEntry 4 }
fsMIBgp4TCPMKTAuthTcpOptExc OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Exclude TCP options other than TCP-AO during MAC calculation,
if fsMIBgp4TCPMKTAuthTcpOptExc is not set TCP-AO MAC will
be calculated on tcp segment including all other TCP options"
::= { fsMIBgp4TCPMKTAuthEntry 5 }
fsMIBgp4TCPMKTAuthRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable represents the status of the MKT entry, can
have values allowed for RowStatus, eg. createAndGo, destroy etc "
::= { fsMIBgp4TCPMKTAuthEntry 6 }
--MIB for TCP-AO config for BGP peers
fsMIBgp4TCPAOAuthPeer OBJECT IDENTIFIER ::= {fsMIBgp 43}
--BGP TCP-AO config Table
fsMIBgp4TCPAOAuthPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF Fsbgp4TCPAOAuthPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"TCP-AO Peer config Table"
::= { fsMIBgp4TCPAOAuthPeer 1 }
fsMIBgp4TCPAOAuthPeerEntry OBJECT-TYPE
SYNTAX Fsbgp4TCPAOAuthPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry corresponds to the TCP-AO configs for peer,
Support for associating one keyId(MKT) per peer is available at
present. If a new keyId/MKT is associated with a peer which
already has one associated keyId/MKT, existing values will
be overwritten with new one.
Configuration support for start accept, start generate, stop accept
and stop generate are not available currently"
INDEX {
fsMIBgp4ContextId,
fsMIBgp4TCPAOAuthPeerType,
fsMIBgp4TCPAOAuthPeerAddr,
fsMIBgp4TCPAOAuthKeyId
}
::= { fsMIBgp4TCPAOAuthPeerTable 1 }
Fsbgp4TCPAOAuthPeerEntry ::= SEQUENCE {
fsMIBgp4TCPAOAuthPeerType
InetAddressType,
fsMIBgp4TCPAOAuthPeerAddr
InetAddress,
fsMIBgp4TCPAOAuthKeyId
Integer32,
fsMIBgp4TCPAOAuthKeyStatus
INTEGER,
fsMIBgp4TCPAOAuthKeyStartAccept
DateAndTime,
fsMIBgp4TCPAOAuthKeyStartGenerate
DateAndTime,
fsMIBgp4TCPAOAuthKeyStopGenerate
DateAndTime,
fsMIBgp4TCPAOAuthKeyStopAccept
DateAndTime
}
fsMIBgp4TCPAOAuthPeerType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address type of the peer IP address"
::= { fsMIBgp4TCPAOAuthPeerEntry 1 }
fsMIBgp4TCPAOAuthPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of this the peer for which TCP-AO config is done"
::= { fsMIBgp4TCPAOAuthPeerEntry 2 }
fsMIBgp4TCPAOAuthKeyId OBJECT-TYPE
SYNTAX Integer32 (0 .. 255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Key id of the MKT which need to be associated with the peer"
::= { fsMIBgp4TCPAOAuthPeerEntry 3 }
fsMIBgp4TCPAOAuthKeyStatus OBJECT-TYPE
SYNTAX INTEGER
{
set (1),
clear(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" While doing a write on the object(snmpset) the value
'set(1)' will associate the MKT with KeyId mentioned
in the index to the peer
'clear(2)' will clear/dissociate the keyId mentioned
in the index to the peer
During read/snmpget on the ogject the value
'set(1)' will indicate TCP-AO is enabled and the value
returned by fsbgp4TCPAOAuthKeyId is valid
Read on object will not display clear"
::= { fsMIBgp4TCPAOAuthPeerEntry 4 }
fsMIBgp4TCPAOAuthKeyStartAccept OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The date & time the router will start accepting packets that have
been created with the MKT specified by the key-id."
DEFVAL { "0000000000000000" }
::= { fsMIBgp4TCPAOAuthPeerEntry 5 }
fsMIBgp4TCPAOAuthKeyStartGenerate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The date & time the router will start using the MKT specified by the
key-id for packets generation."
DEFVAL { "0000000000000000" }
::= { fsMIBgp4TCPAOAuthPeerEntry 6 }
fsMIBgp4TCPAOAuthKeyStopGenerate OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The date & time the router will stop using the MKT specified by
the key-id for packets generation."
DEFVAL { "0000000000000000" }
::= { fsMIBgp4TCPAOAuthPeerEntry 7 }
fsMIBgp4TCPAOAuthKeyStopAccept OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The date & time the router will stop accepting packets that have
been created withthe MKT specified by the key-id."
DEFVAL { "0000000000000000" }
::= { fsMIBgp4TCPAOAuthPeerEntry 8 }
-- ORF table
fsMIBgp4ORFListTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsMIBgp4ORFListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table for adding/removing Outbound Route Filter entries received from the peer"
::= { fsMIBgp 44 }
fsMIBgp4ORFListEntry OBJECT-TYPE
SYNTAX FsMIBgp4ORFListEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry describing the bgp ORF list."
INDEX { fsMIBgp4ContextId,
fsMIBgp4ORFPeerAddrType,
fsMIBgp4ORFPeerAddr,
fsMIBgp4ORFAfi,
fsMIBgp4ORFSafi,
fsMIBgp4ORFType,
fsMIBgp4ORFSequence,
fsMIBgp4ORFAddrPrefix,
fsMIBgp4ORFAddrPrefixLen,
fsMIBgp4ORFMinLength,
fsMIBgp4ORFMaxLength,
fsMIBgp4ORFAction
}
::= { fsMIBgp4ORFListTable 1 }
FsMIBgp4ORFListEntry ::= SEQUENCE {
fsMIBgp4ORFPeerAddrType InetAddressType,
fsMIBgp4ORFPeerAddr InetAddress,
fsMIBgp4ORFAfi InetAddressType,
fsMIBgp4ORFSafi BgpSafi,
fsMIBgp4ORFType Unsigned32,
fsMIBgp4ORFSequence Unsigned32,
fsMIBgp4ORFAddrPrefix InetAddress,
fsMIBgp4ORFAddrPrefixLen Unsigned32,
fsMIBgp4ORFMinLength Unsigned32,
fsMIBgp4ORFMaxLength Unsigned32,
fsMIBgp4ORFAction INTEGER
}
fsMIBgp4ORFPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the address type of the BGP peer
associated with this ORF entry"
::= { fsMIBgp4ORFListEntry 1 }
fsMIBgp4ORFPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the remote address of the BGP peer
associated with this ORF entry"
::= { fsMIBgp4ORFListEntry 2 }
fsMIBgp4ORFAfi OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the type of IP address prefix in the ORF entry."
::= { fsMIBgp4ORFListEntry 3 }
fsMIBgp4ORFSafi OBJECT-TYPE
SYNTAX BgpSafi
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the Sub-sequent address family of
IP address prefix in the ORF entry."
::= { fsMIBgp4ORFListEntry 4 }
fsMIBgp4ORFType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the type of the ORF entry.
Currently it supports only Address-Prefix based ORF type (64)"
::= { fsMIBgp4ORFListEntry 5 }
fsMIBgp4ORFSequence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the sequential order in which a route should be
matched against an ORF entry."
::= { fsMIBgp4ORFListEntry 6 }
fsMIBgp4ORFAddrPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the IP address prefix for which the ORF rule was specified."
::= { fsMIBgp4ORFListEntry 7 }
fsMIBgp4ORFAddrPrefixLen OBJECT-TYPE
SYNTAX Unsigned32 (0..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the length of the IP address prefix length in bits which will be
considered when matching a route with the ORF entry."
::= { fsMIBgp4ORFListEntry 8 }
fsMIBgp4ORFMinLength OBJECT-TYPE
SYNTAX Unsigned32 (0..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the minimum prefix-length in bits for a IP address prefix.
Any route with prefix-length equal to or greater than this length will be
considered as a match, if fsMIBgp4ORFMaxLength is not specified.
If it is ZERO, it will be considered as unspecified and it will not be considered
while applying the rule. If both fsMIBgp4ORFMinLength and fsMIBgp4ORFMaxLength are specified,
then a route with prefix-length with in the range of fsMIBgp4ORFMinLength and
fsMIBgp4ORFMaxLength will be considered as a match"
::= { fsMIBgp4ORFListEntry 9 }
fsMIBgp4ORFMaxLength OBJECT-TYPE
SYNTAX Unsigned32 (0..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the maximum prefix-length in bits for a IP address prefix.
Any route with prefix-length equal to or less than this length will be
considered as a match, if fsMIBgp4ORFMinLength is not specified.
If it is ZERO, then it will be considered as unspecified and it will not be considered
while applying the rule.If both fsMIBgp4ORFMaxLength and fsMIBgp4ORFMinLength are specified,
then a route with prefix-length with in the range of fsMIBgp4ORFMinLength and
fsMIBgp4ORFMaxLength will be considered as a match"
::= { fsMIBgp4ORFListEntry 10 }
fsMIBgp4ORFAction OBJECT-TYPE
SYNTAX INTEGER {
permit (0),
deny (1)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the action to be taken for a particular route
if it matches with the ORF rules defined in this particular ORF entry.
If it is PERMIT, then the matched route will be advertised to the peer.
Else if it is DENY, then the matched route will not be advertised to the peer"
::= { fsMIBgp4ORFListEntry 11 }
END
View Git Blame Copy Permalink