WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/hp/LaserJet4V-MIB

2651 lines
109 KiB
Plaintext
Raw Permalink Blame History

-- (C) COPYRIGHT HEWLETT-PACKARD COMPANY 1997.
--
-- LaserJet 4V Printer Model Specific MIB.
--
-- Generated on August 4, 1997.
--
-- Company names and product names mentioned herein may be
-- trademarks, and/or registered trademarks of their respective
-- companies.
--
-- For interal and external use.
--
-- This MIB describes all the printer model specific
-- objects suppported by the LaserJet 4V printer
-- when networked connected using a JetDirect print
-- server.
--
-- The following MIB also contain objects supported
-- by a JetDirect connected LaserJet 4V printer:
--
-- rfc 1213 MIB II
--
-- This MIB complies with the following RFCs:
--
-- rfc 1157 Simple Network Management Protocol
-- rfc 1155 Structure of Management Information
--
-- Notes:
--
-- 1) At the time this MIB was published, a
-- defect existed where the printer would not correctly
-- handle an SNMP get next request. The printer
-- behavior is correct for tabular objects, but not
-- scalar objects. For example, energy-star, sleep-mode,
-- and on-off-line are all scalars with OIDS:
--
-- energy-star { dm 1 1 1 1 }
-- sleep-mode { dm 1 1 1 2 }
-- on-off-line { dm 1 2 2 5 }
--
-- These three objects are the first three objects supported
-- under the dm tree.
--
-- The printer operation (using OpenView tools as an
-- example) is:
--
-- snmpnext hpb18207 .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2.0
--
-- with a reply of:
--
-- hp.nm.hpsystem.net-peripheral.netdm.dm.device.system.status-system.
-- on-off-line.0 : INTEGER: eOnline
--
-- which the printer handles correctly.
--
-- However, if the zero is left off the end, then the printer operation
-- is:
--
-- snmpnext hpb18207 .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2
--
-- with a reply of:
--
-- hp.nm.hpsystem.net-peripheral.netdm.dm.device.system.status-system.
-- on-off-line.0 : INTEGER: eOnline
--
-- which is incorrect. The object that should have been returned is
-- the energy-star object, not the on-off-line object.
--
-- Since the OpenView MIB Browser uses the get next command in an
-- attempt to retrieve all the supported objects under the specified OID
-- =======================
-- (object identifier) and the printer returns an object that is not under
-- the specified OID, the MIB Browser assumes there are no objects
-- supported under the specified OID and reports "no value (s) returned for
-- query".
--
-- If you use an SNMP tool other than OpenView MIB Browser to do a get,
-- the printer properly responds.
--
-- Retrieving tables using the OpenView MIB Browser works fine. Only
-- retrieving scalar objects fails.
--
-- 2) Proprietary Objects containing a string which are defined in this
-- MIB use the first two bytes to hold the symbol set used to encode
-- the string. The Roman-8 symbol set has a hex encoding of 0x0115.
-- Other symbol sets are listed in the PCL 5 Comparison Guide in table
-- C-1 Symbol Set Values. Standard Printer MIB (prt...objects) and
-- Host Resources MIB (hr...objects) strings do not contain symbol
-- set information.
--
-- 3) Some of the objects included are only supported if an accessory
-- is installed. These accessories include:
-- MIO/EIO based accessories
-- SIMM/DIMM based accessories
-- Mass storage devices
-- Paper handling accessories
-- Adobe PostScript accessory
--
--
LaserJet4V-MIB DEFINITIONS ::= BEGIN
IMPORTS
enterprises FROM SNMPv2-SMI,
DisplayString FROM SNMPv2-TC;
hp OBJECT IDENTIFIER ::= { enterprises 11 }
nm OBJECT IDENTIFIER ::= { hp 2 }
hpsystem OBJECT IDENTIFIER ::= { nm 3 }
net-peripheral OBJECT IDENTIFIER ::= { hpsystem 9 }
netdm OBJECT IDENTIFIER ::= { net-peripheral 4 }
dm OBJECT IDENTIFIER ::= { netdm 2}
device OBJECT IDENTIFIER ::= { dm 1 }
system OBJECT IDENTIFIER ::= { device 1 }
settings-system OBJECT IDENTIFIER ::= { system 1 }
status-system OBJECT IDENTIFIER ::= { system 2 }
display OBJECT IDENTIFIER ::= { status-system 20 }
display-status OBJECT IDENTIFIER ::= { display 1 }
status-message OBJECT IDENTIFIER ::= { display 2 }
status-message1 OBJECT IDENTIFIER ::= { status-message 1 }
id OBJECT IDENTIFIER ::= { system 3 }
interface OBJECT IDENTIFIER ::= { system 4 }
simm OBJECT IDENTIFIER ::= { interface 1 }
simm1 OBJECT IDENTIFIER ::= { simm 1 }
simm2 OBJECT IDENTIFIER ::= { simm 2 }
simm3 OBJECT IDENTIFIER ::= { simm 3 }
simm4 OBJECT IDENTIFIER ::= { simm 4 }
at OBJECT IDENTIFIER ::= { interface 2 }
at1 OBJECT IDENTIFIER ::= { at 1 }
test OBJECT IDENTIFIER ::= { system 5 }
job OBJECT IDENTIFIER ::= { system 6 }
settings-job OBJECT IDENTIFIER ::= { job 1 }
file-system OBJECT IDENTIFIER ::= { system 10 }
file-systems OBJECT IDENTIFIER ::= { file-system 3 }
file-system1 OBJECT IDENTIFIER ::= { file-systems 1 }
errorlog OBJECT IDENTIFIER ::= { system 11 }
error1 OBJECT IDENTIFIER ::= { errorlog 1 }
error2 OBJECT IDENTIFIER ::= { errorlog 2 }
error3 OBJECT IDENTIFIER ::= { errorlog 3 }
error4 OBJECT IDENTIFIER ::= { errorlog 4 }
error5 OBJECT IDENTIFIER ::= { errorlog 5 }
source-subsystem OBJECT IDENTIFIER ::= { device 2 }
io OBJECT IDENTIFIER ::= { source-subsystem 1 }
settings-io OBJECT IDENTIFIER ::= { io 1 }
status-io OBJECT IDENTIFIER ::= { io 2 }
port1 OBJECT IDENTIFIER ::= { io 3 }
parallel OBJECT IDENTIFIER ::= { port1 1 }
processing-subsystem OBJECT IDENTIFIER ::= { device 3 }
pdl OBJECT IDENTIFIER ::= { processing-subsystem 3 }
settings-pdl OBJECT IDENTIFIER ::= { pdl 1 }
status-pdl OBJECT IDENTIFIER ::= { pdl 2 }
pdl-pcl OBJECT IDENTIFIER ::= { pdl 3 }
pdl-postscript OBJECT IDENTIFIER ::= { pdl 4 }
pdl-esc-p OBJECT IDENTIFIER ::= { pdl 5 }
pjl OBJECT IDENTIFIER ::= { processing-subsystem 5 }
destination-subsystem OBJECT IDENTIFIER ::= { device 4 }
print-engine OBJECT IDENTIFIER ::= { destination-subsystem 1 }
status-prt-eng OBJECT IDENTIFIER ::= { print-engine 2 }
intray OBJECT IDENTIFIER ::= { print-engine 3 }
settings-intray OBJECT IDENTIFIER ::= { intray 1 }
status-intray OBJECT IDENTIFIER ::= { intray 2 }
intrays OBJECT IDENTIFIER ::= { intray 3 }
intray1 OBJECT IDENTIFIER ::= { intrays 1 }
intray2 OBJECT IDENTIFIER ::= { intrays 2 }
intray3 OBJECT IDENTIFIER ::= { intrays 3 }
outbin OBJECT IDENTIFIER ::= { print-engine 4 }
outbins OBJECT IDENTIFIER ::= { outbin 3 }
outbin1 OBJECT IDENTIFIER ::= { outbins 1 }
marking-agent OBJECT IDENTIFIER ::= { print-engine 5 }
settings-marking-agent OBJECT IDENTIFIER ::= { marking-agent 1 }
imaging OBJECT IDENTIFIER ::= { print-engine 6 }
energy-star OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the Energy Star sleep value. If the
value is greater than zero, then the device will go into
energy saving sleep mode after the print engine has been
idle for the number of seconds specified by this object.
A value of zero means Energy Star is disabled and the
device will not go to sleep based on print engine idle
time. The value must be non-negative.
Additional information:
Returns or changes the Energy Star sleep value.
The device will go into energy saving sleep
mode after the print engine has been idle for
the number of seconds specified by this
object. LaserJet 4V only supports values of 0, 900, 1800,
3600, 7200, and 10800. A value of 0 means
never go to sleep based on print engine idle
time. Setting to an unsupported value causes
the printer to substitute in a snapped value (listed
below) and to return <noError>
status.
The snapped values are as follow:
<=0 snap to 0
>=1 and <=1349 snap to 900
>=1350 and <=2699 snap to 1800
>=2700 and <=5399 snap to 3600
>=5400 and <=8999 snap to 7200
>=9000 snap to 10800"
::= { settings-system 1 }
sleep-mode OBJECT-TYPE
SYNTAX INTEGER {
eFalse(1),
eTrue(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns eTrue if the device is in energy saving sleep
mode, otherwise returns eFalse. Setting SLEEP-MODE to
eFalse causes the device to wake up, if it is in sleep
mode. Setting SLEEP-MODE to eTrue causes the device to
go into sleep mode.
Additional information:
Setting to eTrue while printer is already in
the Sleep Mode will not change the printer's
current state and should return <noError> status."
::= { settings-system 2 }
control-panel-lock OBJECT-TYPE
SYNTAX INTEGER {
eDisabled(1),
eEnabled(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Device control panel lock. A value of eDisabled means
the control panel is unlocked and the device's
configuration can be modified from the control panel. A
value of eEnabled means the control panel is locked,
thus the device's configuration cannot be modified from
the control panel."
::= { settings-system 8 }
localization-language OBJECT-TYPE
SYNTAX INTEGER {
eEnglish(1),
eFrench(2),
eGerman(3),
eSpanish(4),
eItalian(5),
eSwedish(6),
eDanish(7),
eNorwegian(8),
eDutch(9),
eFinnish(10),
eJapanese(11),
ePortuguese(12),
ePolish(13),
eTurkish(14)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Localization language used by the device for device
generated PML strings, control panel messages, and text
contained in any of the printer generated printed pages.
The order is the same order that is defined in MIO.
Since the MIO values start at zero, one has been added
to each value."
::= { status-system 1 }
not-ready-printer OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indicates if any of the sub-systems in the printer are
not ready. A sub-system is not ready if the sub-system
is unable to perform its function until some sort of
intervention occurs. If there are no items in the NOT-
READY-PRINTER collection (i.e. no bits are set), then
all printer sub- systems are ready. Each sub-system has
a sub-system specific not ready object. If a sub-system
specific not ready object contains any items, then the
associated item will be in the NOT-READY collection."
::= { status-system 2 }
not-ready-controller OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the hardware controller sub-system in the
device is not ready. If there are no items in the
collection (i.e. no bits are set), then the hardware
controller sub-system is ready. If there is an item
present, then the item indicates what is causing the
hardware controller sub-system to be not ready. If the
cControllerFailure item is in the collection, then a
hardware error was detected on the main controller PC
board, sometimes called the formatter or the logic
broad. Example controller hardware errors include DRAM
controller failure, clock failure, memory parity error,
and ROM CRC error. The cFirmwareFailure item is in the
collection if a firmware/software error was detected.
Device specific detailed error information can be
retrieved from the error log objects, if the device
supports those objects. The POS will list which device
failures cause each item to be included in the
collection.
Additional information:
A controller failure occurrence will set the
cControllerFailure bit (bit 1). The controller
failures are: 62.X Service, 63 Service, 65 Service,
67 Service, 68 Service, and 68 Error.
A SIMM failure occurrence will set the cSIMMFailure
bit (bit 2). The SIMM failures are 61.X Service,
53-XY-ZZ Error, and 72 Service.
A DISK failure occurrence will set the cATFailure
bit (bit 3). The DISK failure is FS DISK FAILURE."
::= { status-system 3 }
not-idle OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if any of the sub-systems in the device are
not idle. The I/O source sub-system is considered not
idle if there is unprocessed PDL data in the device.
The PDL processing sub-system is considered not idle if
the device is processing a print job. The print engine
destination sub-system is considered not idle if media
is moving (i.e. the device is printing). [other text
here describing what causes the other sub-systems to be
considered not idle]."
::= { status-system 4 }
on-off-line OBJECT-TYPE
SYNTAX INTEGER {
eOnline(1),
eOffline(2),
eOfflineAtEndOfJob(3)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"To bring the PDL processing sub-system on or off line.
If the device is a printer, then the printer does not
process print job data when the printer is off line.
PML communication persists.
Additional information:
Setting to eOnline while the printer's current
state is Online will not change the current state
and should return <noError> status.
Setting to eOffline while printer's current state is
Offline will not change the current state and should
return <noError> status.
Setting to eOfflineAtEndOfJob when not in a job and
the current state is Online will cause the printer to
change to the Offline state immediately."
::= { status-system 5 }
continue OBJECT-TYPE
SYNTAX INTEGER {
eTrue(1)
}
ACCESS write-only
STATUS optional
DESCRIPTION
"A device can support a class of errors called
continuable errors. When a continuable error is
encountered, the device requires a continue event to
occur before the device will continue operation. One
continue event is setting the CONTINUE object to eTrue.
Devices can support other continue events, like auto-
continue. A continue event causes the continuable error
to be acknowledged, thus allowing the device to
continue. Each device needs to list the continuable
errors. If the device doesn't currently have an
unacknowledged continuable error, the response will
contain <genErr>.
Additional information:
LaserJet 4V supports a class of errors called
continuable errors. When a continuable error is
encountered, LaserJet 4V requires a continue event to
occur before it will continue operation. One
continue event is setting the CONTINUE object to
eTrue. Devices can support other continue events,
like auto-continue. A continue event causes the
continuable error to be acknowledged, thus allowing
LaserJet 4V to continue. If LaserJet 4V doesn't currently
have an unacknowledged continuable error, the
response will contain <noError> status. The following is
a list of continuable errors in LaserJet 4V:
NOT-READY-DESTINATION-PRINT-ENGINE cMarkingAgentOut
NOT-READY-DESTINATION-PRINT-ENGINE cManualFeedMedia
NOT-READY-DESTINATION-PRINT-ENGINE cRequestedMediaUnavailable
NOT-READY-PROCESSING-PDL cSoftResourceMemoryOverflow
NOT-READY-PROCESSING-PDL cPrintDataMemoryOverflow
NOT-READY-SOURCE-IO cDataError
NOT-READY-SOURCE-IO cDataOverrun
NOT-READY-SOURCE-IO cAbnormalConnectionClose
NOT-READY-LASER-PRINT-ENGINE cPrintOverrun
SIMMx-TYPE eUnknown
SIMMx-TYPE eUnSupported
NOT-READY-CONTROLLER cATFailure"
::= { status-system 6 }
auto-continue OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Indicates if the device will automatically continue
after encountering a continuable error. If AUTO-
CONTINUE is set to eOn, the device will automatically
generate continue event to acknowledge continuable
errors. If AUTO-CONTINUE is set to eOff, then some
other continue event will have to acknowledge the
continuable error."
::= { status-system 7 }
user-nvram-reset OBJECT-TYPE
SYNTAX INTEGER {
eTrue(1)
}
ACCESS write-only
STATUS optional
DESCRIPTION
"Setting to eTrue causes all user NVRAM settings to
factory default settings. May also perform POWER-ON-
RESET functionality thus loosing print job data. The
POS will list which objects are effected by a user NVRAM
reset. Some items are NVRAM settings, but not user
controllable, so this action may not cause all of NVRAM
to be reset. Some examples of NVRAM settings that may
not be affected are page count, internally used pen
information, line configuration information, etc.
Additional information:
Setting to eTrue returns the NVRAM items listed
below to their factory default values. Performs
the same function as the 'MENU RESET' function
supported by the control panel except when printer
is in Offline state, setting this OID to eTrue will
not take the printer to the Online state.
DEFAULT-COPIES
DEFAULT-MEDIA-SIZE
DEFAULT-ORIENTATION
DEFAULT-LINES-PER-PAGE
DEFAULT-MANUAL-FEED
DEFAULT-RET
DEFAULT-PRINT-QUALITY
PCL-DEFAULT-FONT-SOURCE
PCL-DEFAULT-FONT-NUMBER
PCL-DEFAULT-FONT-HEIGHT
PCL-DEFAULT-FONT-WIDTH
PCL-DEFAULT-SYMBOL-SET
DEFAULT-VERTICAL-BLACK-RESOLUTION
DEFAULT-HORIZONTAL-BLACK-RESOLUTION
DEFAULT-PDL
CONTEXT-SENSITIVE-PDL-SELECTION
ENERGY-STAR
IO-TIMEOUT
DEFAULT-PAGE-PROTECT
POSTSCRIPT-JAM-RECOVERY (PostScript installed)
POSTSCRIPT-PRINT-ERRORS (PostScript installed)"
::= { status-system 12 }
display-column-size OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates the number of characters displayable on each
row of the printer's display."
::= { display-status 1 }
display-number-of-rows OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates the number of rows displayable on the
printer's display."
::= { display-status 2 }
status-msg-line1-part1 OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"First part of the first line of the printer's status
message.
Additional information:
In the Offline state, device only returns
00 OFFLINE and not the actual content of control panel
display."
::= { status-message1 1 }
total-ram-size OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Identifies total amount of RAM, in bytes, available to
the controller for general computing."
::= { status-system 21 }
status-printer OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Indicates if any of the sub-systems in the device in a
warning condition. A warning condition exists if the
sub-system is useable, but not at its highest state of
functionality."
::= { status-system 22 }
status-controller OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the hardware controller sub-system in a
warning condition."
::= { status-system 23 }
model-number OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Identifies the device model number as listed in the HP
corporate price list (e.g. C2121A for DeskJet 500C).
The string is as specific as possible. Products should
note in POS if the model number on the CPL changes but
the device reports the previous model number. If the
model number changes based on the installed options, the
POS should indicate if only the base model number is
returned, or if the device senses the installed options
and returns the correct model number. If possible,
encode the model number in a symbol set (like Roman-8)
that matches the ASCII character set and limit the
characters used to ASCII characters.
Additional information:
The string is as specific as possible. The
CPL model number will change for an LaserJet 4V when it
is configured as a Dune but only the base product
model number is reported. If possible, encode the
model number in a symbol set (like Roman-8) that
matches the ASCII character set and limit the
characters used to ASCII characters."
::= { id 1 }
model-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Identifies the device model name (e.g. ``DeskJet
1200C''). The string is as specific as possible.
Capitalization and spacing should match family naming
conventions. Products should note in POS if the model
name on the HP corporate price list changes but the
device reports the previous device name. If the model
name changes based on the installed options, the POS
should indicate if only the base model name is returned,
or if the device senses the installed options and
returns the correct model name. If possible, encode the
model name in a symbol set (like Roman-8) that matches
the ASCII character set and limit the characters used to
ASCII characters.
Additional information:
Even though the name of the Dune product
changes to LaserJet 4MV, LaserJet 4V will only report
the base product name LaserJet 4V. If possible,
encode the model name in a symbol set (like Roman-8)
that matches the ASCII character set and limit the
characters used to ASCII characters."
::= { id 2 }
serial-number OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Identifies the serial number for the device. If the
SERIAL-NUMBER object is set by the user, then setting
the object does not need to be protected. If the
SERIAL-NUMBER object is set at the factory, then the
SERVICE-PASSWORD object must be set correctly before the
SERIAL-NUMBER object is writable. If this is a writable
object, the POS should indicate the maximum supported
string length. If possible, encode the serial number in
a symbol set (like Roman-8) that matches the ASCII
character set and limit the characters used to ASCII
characters."
::= { id 3 }
fw-rom-datecode OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Identifies the base system firmware date code. The date
code will be encoded in the yyyymmdd format. There may
be several versions of the base system firmware. The
date code associated with the version of the base system
firmware that is being used is reported. There may be
other date code objects for other specific modules such
as fonts, localization modules, etc. ; these other
datecode objects are device specific."
::= { id 5 }
device-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS optional
DESCRIPTION
"User defined device name. The POS should indicate the
maximum supported string length. If the user entered
string is too long, the device will store as much as
possible and will return the <noError>.
Additional information:
The maximum supported string length is 32
characters. If the user entered string is too long,
the device will store as much as possible and will
return the <noError> status."
::= { id 10 }
device-location OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS optional
DESCRIPTION
"User defined device location. The POS should indicate
the maximum supported string length. If the user
entered string is too long, the device will store as
much as possible and will return the <noError>.
Additional information:
The maximum supported string length is 16
characters. If the user entered string is too long,
the device will store as much as possible and will
return the <noError> status."
::= { id 11 }
asset-number OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS optional
DESCRIPTION
"User defined asset number. The POS should indicate the
maximum supported string length. If the user entered
string is too long, the device will store as much as
possible and will return the <noError>.
Additional information:
The maximum supported string length is 8
characters. If the user entered string is too long,
the device will store as much as possible and will
return the <noError> status."
::= { id 12 }
system-contact OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS optional
DESCRIPTION
"User defined string containing the name of the person or
group that is responsible for the device. The POS
should indicate the maximum supported string length. If
the user entered string is too long, the device will
store as much as possible and will return the
<noError>.
Additional information:
User defined system contact. The maximum
supported string length is 16 characters. If the user
entered string is too long, the device will store as
much as possible and will return the
<noError> status."
::= { id 13 }
simm1-type OBJECT-TYPE
SYNTAX INTEGER {
eEmpty(1),
eUnknown(2),
eUnSupported(3),
eReadOnlyMemory(4),
eVolatileRandomAccessMemory(5)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the type of option installed in
SIMM slot 1. eEmpty means the device did not detect any
option installed in the interface slot. eUnknown means
the device doesn't recognize the installed option.
eUnSupported means the device recognizes the installed
option, but does not support the option.
eReadOnlyMemory means the installed option contains ROM
ICs. eVolatileRandomAccessMemory means the installed
option contains RAM ICs that loose data when the power
is turned off. eNonVolatileRandomAccessMemory means
that the installed option contains RAM ICs that do not
loose data when the power is turned off. eFlashMemory
means that the installed option contains a type of non-
volatile RAM that needs to be erased before it can be
written. eDiskDrive means the installed option contains
a disk drive. eRamRom means the installed option
contains both volatile random access memory and read
only memory. eInputPHD means the installed option is an
input paper handling device. eOutputPHD means the
installed option is an output paper handling device."
::= { simm1 4 }
simm1-capacity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the capacity of the SIMM
installed in SIMM slot 1. The capacity is dependent on
the type of option, as indicated by the SIMM1-TYPE
object. This object has no meaning if the installed
option type is eUnknown or eReadOnlyMemory. This object
contains the size, in bytes, if the installed option
type is eVolatileRandomAccessMemory,
eNonVolatileRandomAccessMemory, eFlashMemory, or
eDiskDrive. If the type of the installed option is
eRamRom, this object contains the size, in bytes, of the
random access memory. If the type of the installed
option is eInputPHD, the capacity indicates the number
of input trays supported by the installed option. If
the type of the installed option is eOutputPHD, the
capacity indicates the number of output bins supported
by the installed option.
Additional information:
Returns an indication of the capacity of the
installed option in bytes. This object is not
supported unless the SIMM1-TYPE type is
eVolatileRandomAccessMemory."
::= { simm1 5 }
simm2-type OBJECT-TYPE
SYNTAX INTEGER {
eEmpty(1),
eUnknown(2),
eUnSupported(3),
eReadOnlyMemory(4),
eVolatileRandomAccessMemory(5)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the type of option installed in
SIMM slot 2. See SIMM1-TYPE for a description."
::= { simm2 4 }
simm2-capacity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the capacity of the SIMM
installed in SIMM slot 2. See SIMM1-CAPACITY for a
description.
Additional information:
Returns an indication of the capacity of the
installed option in bytes. This object is not
supported unless the SIMM2-TYPE type is
eVolatileRandomAccessMemory."
::= { simm2 5 }
simm3-type OBJECT-TYPE
SYNTAX INTEGER {
eEmpty(1),
eUnknown(2),
eUnSupported(3),
eReadOnlyMemory(4),
eVolatileRandomAccessMemory(5)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the type of option installed in
SIMM slot 3. See SIMM1-TYPE for a description."
::= { simm3 4 }
simm3-capacity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the capacity of the SIMM
installed in SIMM slot 3. See SIMM1-CAPACITY for a
description.
Additional information:
Returns an indication of the capacity of the
installed option in bytes. This object is not
supported unless the SIMM3-TYPE type is
eVolatileRandomAccessMemory."
::= { simm3 5 }
simm4-type OBJECT-TYPE
SYNTAX INTEGER {
eEmpty(1),
eUnknown(2),
eUnSupported(3),
eReadOnlyMemory(4),
eVolatileRandomAccessMemory(5)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the type of option installed in
SIMM slot 4. See SIMM1-TYPE for a description."
::= { simm4 4 }
simm4-capacity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the capacity of the SIMM
installed in SIMM slot 4. See SIMM1-CAPACITY for a
description.
Additional information:
Returns an indication of the capacity of the
installed option in bytes. This object is not
supported unless the SIMM4-TYPE type is
eVolatileRandomAccessMemory."
::= { simm4 5 }
at1-model-number OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Identifies the AT model number. If the disk was
manufactured by HP, then the model number is the one
listed in the HP corporate price list. If possible,
encode the model number in a symbol set (like Roman-8)
that matches the ASCII character set and limit the
characters used to ASCII characters.
Additional information:
The model number is obtained from the disk
using the IDE (Intelligent Drive Electronics)
Identify command. This objects is only supported
if a disk is installed. Returns
<noSuchName> status if attempting
to perform a Get on this OID with no disk installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { at1 1 }
at1-model-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns product information identifying the AT storage
device. Example: C3014A
Additional information:
The product information is obtained from the
disk using the IDE (Intelligent Drive Electronics)
Identify command. This objects is only supported
if a disk is installed. Returns
<noSuchName> status if attempting
to perform a Get on this OID with no disk installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { at1 2 }
at1-manufacturing-info OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns information describing the manufacture of this
particular AT. May include serial number and firmware
revision.
Additional information:
Returns the model number, serial number, and
firmware revision of the installed disk. This
information is obtained from the disk using the
IDE (Intelligent Drive Electronics) Identify
command. Example: HP C3014A JP932412W9 K2A4A059.
This objects is only supported if a disk is installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no disk
installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { at1 3 }
at1-type OBJECT-TYPE
SYNTAX INTEGER {
eEmpty(1),
eDiskDrive(8)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the type of option installed in
this particular AT interface. See SIMM1-TYPE for an
explanation of the enumerations.
Additional information:
eEmpty means the device did not detect any AT.
eDiskDrive means the AT contains a disk drive."
::= { at1 4 }
at1-capacity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns an indication of the capacity of the installed
option. See SIMM1-CAPACITY for an explanation of the
meaning of the value of this object.
Additional information:
This object contains the size, in bytes, of
the installed disk option. This objects is only
supported if a disk is installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no disk
installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { at1 5 }
self-test OBJECT-TYPE
SYNTAX INTEGER {
eNotInASelfTest(1),
eDestructiveSelfTest(3)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Writing this object allows a device self test to be
started. Reading this object provides an indication
what self-test is currently executing, if any. Actual
self-test operation is device specific. A self test may
not be allowed at any arbitrary time. If the device
supports the requested self test, but can not start the
execution of the self test when requested, the device
will respond with <genErr>. If a non-destructive
self test is being started, the device
will generate a response before the self test is
completed.
RECOMMENDATION: If the device is ready (i.e. the NOT-
READY object does not contain any items, except maybe
being off-line) and is idle (i.e. the NOT-IDLE object
does not contain any items), this request should always
succeed. This provides a mechanism for driver writers
to always determine if the action will succeed or not.
Additional information:
After the self-test is complete a
configuration page will be printed. This is the
recommended way to cause a configuration page to be
printed. A continuous self test cannot be started
or terminated using this OID. A self test is not be
allowed at any arbitrary time. If the requested self
test cannot be started LaserJet 4V will respond with
<genErr> status. No response will be generated
because of the destructive nature of
this test. Can only be started if LaserJet 4V is ready
(except for being offline), offline, and idle. If
LaserJet 4V is ready (i.e. the NOT-READY object does
not contain any items, except for being off-line),
is offline, and is idle (i.e. the NOT-IDLE object
does not contain any items), this request should
always succeed. This provides a mechanism for driver
writers to always determine if the action will
succeed or not."
::= { test 1 }
print-internal-page OBJECT-TYPE
SYNTAX INTEGER {
eNotPrintingAPage(1),
ePrintingAnUnknownInternalPage(2),
ePCLDemoPage2(301),
ePCLFontList1(350),
ePostScriptDemoPage1-ConfigurationPage(400),
ePostScriptDemoPage2(401),
ePostScriptFontList1(450)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Writing this object to a value other than
eNotPrintingAnInternalPage causes the device to attempt
to print an internally generated page. Reading this
object provides an indication what internally generated
page is currently being printed, if any. The actual
page is device specific. Some devices may support
continuously printing an internally generated page.
Setting this object to eNotPrintingAnInternalPage
terminates continuously printing internally generated
pages. An internally generated page may not be allowed
to be printed at any arbitrary time; under what
conditions it will succeed or fail is device specific.
If the device supports the requested page, but can not
start printing the page when requested, the device will
respond with <genErr>.
RECOMMENDATION: If the device is ready (i.e. the NOT-
READY object does not contain any items, except maybe
being off-line) and is idle (i.e. the NOT-IDLE object
does not contain any items), this request should always
succeed. This provides a mechanism for driver writers
to always determine if the action will succeed or not.
Additional information:
ePCLDemoPage1-ConfigurationPage (the PCL
test page) is not supported. The PCL
configuration page is generated by using
the SELF-TEST OID above. ePCLDemoPage2
is the PCL Demo page, and ePCLFontList1
is the PCL typeface list.
ePostScriptDemoPage1-ConfigurationPage is
the PostScript configuration page. The
ePostScriptDemoPage2 is the same PostScript demo
page that can be printed via the control
panel. ePostScriptFontList1 is the
PostScript typeface list. LaserJet 4V does
not support continuously printing a demo
page. A page is not allowed at any
arbitrary time. LaserJet 4V must be ready
(except for being offline), offline, and idle
before a page can be printed. If the
requested page cannot start printing when
requested, LaserJet 4V will respond with
<genErr> status. IfLaserJet 4V is ready (i.e. the NOT-READY
object does not contain any items, except
being off-line). offline, and is idle (i.e. the
NOT-IDLE object does not contain any
items), this request should always
succeed. This provides a mechanism for
driver writers to always determine if the
action will succeed or not.
When PostScript option is not installed, LaserJet 4V will
respond with <genErr> status for any attempt to write this object to
ePostScriptDemoPage1-ConfigurationPage,
ePostScriptDemoPage2, and ePostScriptFontList1."
::= { test 2 }
clearable-warning OBJECT-TYPE
SYNTAX INTEGER {
eOn(2),
eJob(3)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or controls how the device will track clearable
warnings. A clearable warning indicates a transient
event in the device. The device will continue after the
transient event occurs. If CLEARABLE-WARNING is eOff,
the device does not track clearable warnings. If
CLEARABLE-WARNING is eOn, all clearable warnings will be
tracked until cleared (acknowledged). If CLEARABLE-
WARNING is eJob, a clearable warning generated due to an
event that occurs because of the print job being
processed will be automatically cleared when the device
has finished processing the job. Example clearable
warning events include the device altering resolution or
page protection due to memory constraints. The POS will
document what transient events are treated as clearable
warnings.
Additional information:
Returns information on how the device will track
clearable warnings. A clearable warning indicates a
transient event in the device. The device will
continue after the transient event occurs. If
CLEARABLE-WARNING is eOn, all clearable warnings
will be tracked until cleared (acknowledged). If
CLEARABLE-WARNING is eJob, a clearable warning
generated due to an event that occurs because of the
print job being processed will be automatically cleared
when the device has finished processing the job.
Example clearable warning events include the device
altering resolution or page protection due to memory
constraints. "
::= { settings-job 1 }
file-system1-initialized OBJECT-TYPE
SYNTAX INTEGER {
eFalse(1),
eTrue(2)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns eTrue if a file system has been written to the
mass storage device(s) which will hold file data
contained in this file system. Returns eFalse
otherwise. Each POS needs to specify the relationship
between file systems and the physical storage devices
that can hold the data contained in those file systems.
Additional information:
This objects is only supported if a disk is
installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no disk
installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { file-system1 1 }
file-system1-capacity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the total size, in bytes, of the mass storage
space configured to hold the file data (and file system
information) assoicated with files stored in this file
system. This refers to hardware capacity, independent
of any space consumed by the file system overhead or
user files.
Additional information:
This objects is only supported if a disk is
installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no disk
installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { file-system1 2 }
file-system1-free-space OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the total amount, in bytes, of unused storage
space currently available to this file system.
Additional information:
This objects is only supported if a disk is
installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no disk
installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { file-system1 3 }
file-system1-write-protect OBJECT-TYPE
SYNTAX INTEGER {
eDisabled(1),
eEnabled(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Supports write-protecting the file system. Setting
FILE-SYSTEM-WRITE-PROTECT to eEnabled blocks any
modification of the contents of the file system.
Setting FILE-SYSTEM-WRITE-PROTECT to eDisabled allows
modification of the contents of the file system.
Additional information:
This objects is only supported if a disk is
installed.
Returns <noSuchName> status if
attempting to perform a Get, or Set on this OID
with no disk installed.
Returns <noSuchName>
status if attempting to perform an EnableTrap, or
DisableTrap on this OID with no disk installed."
::= { file-system1 4 }
error1-time-stamp OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains some sort of time stamp indicating when error 1
occurred. Example time stamps include the actual time
the error occurred (in seconds since Jan. 1, 1970), and
the total engine page count. The device POS documents
the meaning of the time stamp.
Additional information:
Contains a time stamp indicating when error 1
occurred. In LaserJet 4V this item contains the engine
page count when the error occurred."
::= { error1 1 }
error1-code OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains a device specific error code. Each device POS
should list what errors are logged to the error log and
the meaning of each supported error code value.
Additional information:
Contains a device specific error code."
::= { error1 2 }
error2-time-stamp OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains some sort of time stamp indicating when error 2
occurred. Example time stamps include the actual time
the error occurred (in seconds since Jan. 1, 1970), and
the total engine page count. The device POS documents
the meaning of the time stamp.
Additional information:
Contains a time stamp indicating when error 2
occurred. In LaserJet 4V this item contains the engine
page count when the error occurred."
::= { error2 1 }
error2-code OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains a device specific error code. Each device POS
should list what errors are logged to the error log and
the meaning of each supported error code value.
Additional information:
Same as ERROR1-CODE."
::= { error2 2 }
error3-time-stamp OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains some sort of time stamp indicating when error 3
occurred. Example time stamps include the actual time
the error occurred (in seconds since Jan. 1, 1970), and
the total engine page count. The device POS documents
the meaning of the time stamp.
Additional information:
Contains a time stamp indicating when error 3
occurred. In LaserJet 4V this item contains the engine
page count when the error occurred."
::= { error3 1 }
error3-code OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains a device specific error code. Each device POS
should list what errors are logged to the error log and
the meaning of each supported error code value.
Additional information:
Same as ERROR1-CODE."
::= { error3 2 }
error4-time-stamp OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains some sort of time stamp indicating when error 4
occurred. Example time stamps include the actual time
the error occurred (in seconds since Jan. 1, 1970), and
the total engine page count. The device POS documents
the meaning of the time stamp.
Additional information:
Contains a time stamp indicating when error 4
occurred. In LaserJet 4V this item contains the engine
page count when the error occurred."
::= { error4 1 }
error4-code OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains a device specific error code. Each device POS
should list what errors are logged to the error log and
the meaning of each supported error code value.
Additional information:
Same as ERROR1-CODE."
::= { error4 2 }
error5-time-stamp OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains some sort of time stamp indicating when error 5
occurred. Example time stamps include the actual time
the error occurred (in seconds since Jan. 1, 1970), and
the total engine page count. The device POS documents
the meaning of the time stamp.
Additional information:
Contains a time stamp indicating when error 5
occurred. In LaserJet 4V this item contains the engine
page count when the error occurred."
::= { error5 1 }
error5-code OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains a device specific error code. Each device POS
should list what errors are logged to the error log and
the meaning of each supported error code value.
Additional information:
Same as ERROR1-CODE."
::= { error5 2 }
io-timeout OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"The amount of time, in seconds, to wait for more print
job data to be received before an I/O timeout occurs.
The I/O channel being timed is the I/O channel that
received the data associated with the current print job.
If an I/O timeout occurs, the PDL processing sub-system
assumes all the data associated with the current print
job has been received, and processes the end of job in
an PDL specific manner. The POS specifies the supported
values.
Additional information:
The amount of time, in seconds, to wait
for more print job data to be received before an I/O
timeout occurs. The I/O channel being timed is the I/O
channel that received the data associated with the
current print job. If an I/O timeout occurs, the PDL
processing sub-system assumes all the data associated
with the current print job has been received, and
processes the end of job in an PDL specific manner.
In LaserJet 4V the supported values are 5 to 300 seconds.
Setting to a value outside the supported range returns
<badValue> status."
::= { settings-io 1 }
io-switch OBJECT-TYPE
SYNTAX INTEGER {
eYes(1)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the device will switch between I/O channels
when a job boundary is encountered and print job data is
available on another I/O channel."
::= { settings-io 2 }
io-buffering OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2),
eAuto(3)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or controls the manner in which the device
performs I/O data buffering. I/O data buffering allows
additional print job data to be buffered by the I/O sub-
system in an effort to allow the computer sending the
data to perform other tasks and to keep the PDL
processing sub-system busy. eOff, I/O buffering is
disabled. When eOn, I/O buffering is enabled and the
IO-BUFFER-SIZE object controls the amount of memory set
aside for I/O buffer. When eAuto, I/O buffering is
enabled and the I/O buffer size is determined
automatically by the device and the IO-BUFFER-SIZE
object is not used.
Additional information:
Returns the manner in which the device
performs I/O data buffering. I/O data buffering allows
additional print job data to be buffered by the I/O
sub- system in an effort to allow the computer sending
the data to perform other tasks and to keep the PDL
processing sub-system busy. eOff, I/O buffering is
disabled. When eOn, I/O buffering is enabled and the
IO-BUFFER-SIZE object controls the amount of memory set
aside for I/O buffer. When eAuto, I/O buffering is
enabled and the I/O buffer size is determined
automatically by the device and the IO-BUFFER-SIZE
object is not used."
::= { settings-io 5 }
io-buffer-size OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or configures the amount of memory, in bytes,
dedicated to I/O print job data buffering. Attempting
to set to an unsupported value causes the device to use
the closest supported value. Each device POS should
document the list of supported values.
Additional information:
Returns the amount of memory, in bytes,
dedicated to I/O print job data buffering.
In LaserJet 4V the minimum supported value is 10,000.
The maximum supported value is dependent on total
memory installed and the amount of memory currently
being used by other memory consumers.
Between the values of 10,000 and 90,000 only even
increments of 10.000 are supported.
From 100,000 to the maximum only even increments of
100.000 are supported."
::= { settings-io 6 }
maximum-io-buffering-memory OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the maximum amount of additional memory, in
bytes, that can be dedicated to buffering print job
data."
::= { settings-io 7 }
not-ready-source-io OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the I/O sub-system in the device is not
ready. If there are no items in the collection (i.e. no
bits are set), then the I/O sub-system is ready. If
there is an item present, then the item indicates what
is causing the I/O sub-system to be not ready. If the
I/O sub-system is not ready due to a soft error, the
soft error is considered to be an auto-continuable
error, thus it can be acknowledged by setting the
CONTINUE object to eTrue."
::= { status-io 1 }
status-source-io OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the I/O sub-system in a warning condition."
::= { status-io 2 }
parallel-speed OBJECT-TYPE
SYNTAX INTEGER {
eSlow(1),
eFast(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the maximum parallel I/O port speed.
An eSlow setting causes a 10 us busy pulse per received
byte of data. An eFast setting causes a 1.5 us busy
pulse per received byte of data. In rare cases, setting
this value to eFast can cause the parallel port to no
longer transfer data reliably."
::= { parallel 4 }
parallel-bidirectionality OBJECT-TYPE
SYNTAX INTEGER {
eUnidirectional(1),
eBidirectional(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes whether the parallel I/O port
supports bidirectional communication."
::= { parallel 5 }
default-orientation OBJECT-TYPE
SYNTAX INTEGER {
ePortrait(1),
eLandscape(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the default orientation. The list of
supported values should be documented in the device
POS."
::= { settings-pdl 2 }
default-copies OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes default copies. Default copies is
the default values used by the PDL to control the number
of copies of each page in the print job that are
printed. The print job can override this value. The
list of supported values should be documented in the
device POS.
Additional information:
Returns or changes default copies. Default
copies is the default values used by the PDL to
control the number of copies of each page in the
print job that are printed. The print job can
override this value. The supported values are 1
through 999. Setting to an unsupported value causes
the printer to substitute in a snap value
(listed below) and to return
<noError> status.
The snap are as follow:
<1 snaps to 1
>999 snaps to 999"
::= { settings-pdl 4 }
form-feed OBJECT-TYPE
SYNTAX INTEGER {
eTrue(1)
}
ACCESS write-only
STATUS optional
DESCRIPTION
"Instructs the PDL processing sub-system to finishing
processing the current page of the current job. Form
feed is also known as close page or eject page. If the
PDL processing sub-system is in a FORM-FEED-NEEDED
state, this causes the device to flush or finish
processing the current page of the current job. If the
device is not in the FORM-FEED-NEEDED state, an
<genErr> will occur.
Additional information:
Instructs the PDL processing sub-system to
finish processing the current page of the current job.
Form feed is also known as close page or eject page.
If the PDL processing sub-system is in a FORM-FEED-NEEDED
state, this causes the device to flush or finish
processing the current page of the current job. If the
device is not in the FORM-FEED-NEEDED state, a status
<genErr> will be returned. The
printer must be offline before attempting
to perform a form feed, otherwise a status
<genErr> will be returned."
::= { settings-pdl 5 }
resource-saving OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2),
eAuto(3)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or changes PDL resource saving. Resource saving
stores a PDL's permanent soft resources, like fonts,
even when another PDL is active. Resource saving is
also called environment saving. When eOff, resource
saving is disabled. When ON, resource saving is enabled
and memory is set aside for each PDL based on that PDL's
resource saving memory size object, to store that PDL's
permanent soft resources. When eAuto, resource saving
is enabled and memory space for each installed PDL is
determined automatically. The device POS should
document what values are legal when only one PDL is
installed.
Additional information:
When PCL is the only PDL installed in
LaserJet 4V eOn is not a legal value. When PostScript
is installed and less than 12 Meg of DRAM is present
resource saving is not available. When at least 12 Meg
of memory is installed with PostScript then resource
saving becomes available and all three values are
legal.
This object is only supported if PostScript option
is installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no
PostScript option installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no PostScript option
installed."
::= { settings-pdl 6 }
maximum-resource-saving-memory OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the maximum amount of additional memory, in
bytes, that can be dedicated to holding PDL permanent
soft resources."
::= { settings-pdl 7 }
default-vertical-black-resolution OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the value of the default vertical
black resolution. The units are dots per inch.
Additional information:
In LaserJet 4V changing this OID also causes
DEFAULT- HORIZONTAL-BLACK RESOLUTION to change.
DEFAULT- HORIZONTAL-BLACK-RESOLUTION and
DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the
same. The supported values are 300 and 600.
Setting to an unsupported value causes the printer
to substitute in a snap value (listed below) and
to return <noError> status.
The snap values are as follow:
<450 snap to 300
>=450 snap to 600"
::= { settings-pdl 8 }
default-horizontal-black-resolution OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the value of the default horizontal
black resolution. The units are dots per inch.
Additional information:
In LaserJet 4V changing this OID also causes
DEFAULT- VERTICAL-BLACK RESOLUTION to change.
DEFAULT- HORIZONTAL-BLACK-RESOLUTION and
DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the
same. The supported values are 300 and 600.
Setting to an unsupported value causes the printer
to substitute in a snap value (listed below) and to
return <noError> status.
The snap values are as follow:
<450 snap to 300
>=450 snap to 600"
::= { settings-pdl 9 }
default-page-protect OBJECT-TYPE
SYNTAX INTEGER {
eOn(2),
eAuto(3)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the default page protection behavior.
If eOff, the device does not reserve memory for holding
the entire raster form of a processed page. If eOn,
then memory is reserved. If eAuto, the device
determines the amount of memory to reserve."
::= { settings-pdl 10 }
default-lines-per-page OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the default number of lines per page.
The POS indicates the supported values. An unsupported
value causes the printer to use the closest supported
value, causing the printer to return the
<noError>.
Additional information:
The supported values in LaserJet 4V are 5 to 128.
Setting to an unsupported value causes the
the printer to substitute in a snap value (listed
below) and to return <noError>
status.
The snap values are as follow:
<5 snaps to 5
>128 snaps to 128"
::= { settings-pdl 11 }
default-media-size OBJECT-TYPE
SYNTAX INTEGER {
eUSExecutive(1),
eUSLetter(2),
eUSLegal(3),
eLedger(11),
eISOandJISA4(26),
eISOandJISA3(27),
eJISB5(45),
eJISB4(46),
eJapanesePostcardSingle(71),
eJapanesePostcardDouble(72),
eMonarch(80),
eCommercial10(81),
eInternationalDL(90),
eInternationalC5(91),
eInternationalB5(100),
eCustom(101)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"This indicates the default media size. A write of an
unsupported value cases an <badValue>.
Complete list of supported media sizes along
with their dimensions are listed in the ``Media Size
Table'' near the end of this document."
::= { settings-pdl 13 }
not-ready-processing-pdl OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the PDL sub-system in the device is not
ready. If there are no items in the collection (i.e. no
bits are set), then the PDL sub-system is ready. If
there is an item present, then the item indicates what
is causing the PDL sub-system to be not ready. cOffLine
indicates the PDL processing sub-system is off line.
cPrintDataMemoryOverflow indicates the print job was
sufficiently complex to use up all memory available for
processing print job data. cSoftResourceMemoryOverflow
indicates the print job contained soft resources (fonts,
macros, etc.) that over flowed the available memory."
::= { status-pdl 1 }
form-feed-needed OBJECT-TYPE
SYNTAX INTEGER {
eFalse(1),
eTrue(2)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the PDL processing sub-system has made
marks on the current page and the source subsystem has
been idle for a device specific amount of time."
::= { status-pdl 2 }
pcl-datecode OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"This indicates the PCL firmware date code in yyyymmdd
format."
::= { pdl-pcl 1 }
pcl-resource-saving-memory-size OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or changes the amount of resource saving memory
set aside to hold permanent soft PCL resources.
Additional information:
Returns the amount of memory, in
bytes, set aside to hold permanent soft PCL
resources. Additional memory may need to be installed
before this object is supported."
::= { pdl-pcl 2 }
pcl-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains the name of the PDL. For PCL, the name is
`PCL'."
::= { pdl-pcl 3 }
pcl-version OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains the PDL version."
::= { pdl-pcl 4 }
pcl-default-symbol-set OBJECT-TYPE
SYNTAX INTEGER {
eISO60DanishNorwegian(4),
eISO15Italian(9),
eISO88591Latin1ECMA94(14),
eISO11SwedishforNames(19),
eISO6ASCII(21),
eISO4UnitedKingdom(37),
eISO69French(38),
eISO21German(39),
eLegal(53),
eISO88592Latin2ECMA94(78),
eISO17Spanish(83),
ePSMath(173),
eISO88599Latin5ECMA128(174),
eWindows31Latin5(180),
eMicrosoftPublishing(202),
eVenturaMath(205),
eDeskTop(234),
eMath8(269),
eRoman8(277),
eWindows31Latin2(293),
ePC8Turkish(308),
eWindows30Latin1(309),
ePSText(330),
ePC8CodePage437(341),
ePC8DNDanishNorwegian(373),
ePC850Multilingual(405),
eVenturaInternational(426),
eVenturaUS(458),
ePiFont(501),
ePC852Latin2(565),
eWindows31J(619),
eWindows31Latin1(629)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the default PCL symbol set. The
enumeration values match the values supported by the PCL
Symbol Set Code escape sequence, <ESC>*c#R. The binary
representation of the enumerated value is also matches
the PML <SymbolSetValue>.
Additional information:
The eWindows31J enumeration is only supported
if a Japanese font SIMM is installed."
::= { pdl-pcl 11 }
pcl-default-font-height OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the default PCL height. Height is an
approximate measure of the body of the type in
centipoints. A centipoint is 1/7200 inch. Height
applies only to proportional fonts. Point size, in
points, can be converted to font height, in centipoints,
by multiplying the point size by 100. The POS indicates
the supported values. An unsupported value causes the
printer to use the closest supported value, causing the
printer to return <noError>.
''Closest'' means the smallest absolute difference.
Additional information:
In LaserJet 4V this is equivalent to 'POINT SIZE'.
Use the following formula to convert:
PCL-DEFAULT-FONT-HEIGHT = POINT SIZE * 100
Setting to an unsupported value causes the printer to
substitute in a snap value (listed below) and to
return <noError> status.
The snap values are as follow:
<=400 snaps to 400
>=99975 snaps to 99975
Unsupported values in the range 400 to 99975 snaps
DOWN to the previous supported value
(i.e 25293 snaps to 25275 or 75038 snaps to 75025)."
::= { pdl-pcl 13 }
pcl-default-font-source OBJECT-TYPE
SYNTAX INTEGER {
eInternal(1),
ePermanentSoft(2),
eRomSimm1(10),
eRomSimm2(11),
eRomSimm3(12),
eRomSimm4(13)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the value of the default font source
variable in NVRAM."
::= { pdl-pcl 14 }
pcl-default-font-number OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the value of the default font number
variable in NVRAM. Writing an unsupported value causes
the printer to generate an
<badValue>."
::= { pdl-pcl 15 }
pcl-default-font-width OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the default PCL font width. Width is
expressed as the width of a character in centipoints. A
centipoint is 1/7200 inch. Width applies only to fixed
space fonts. Pitch, in character per inch, can be
converted to font width, in centipoints, by dividing
7200 by the pitch. The POS indicates the supported
values. An unsupported value causes the printer to use
the closest supported value, causing the printer to
return <noError>. ''Closest''
means the smallest absolute difference.
Additional information:
In LaserJet 4V this is equivalent to 'PITCH'.
Use the following formula to convert:
PCL-DEFAULT-FONT WIDTH = 7200/PITCH
Setting to an unsupported value causes the printer
to substitute in a snap value (listed below) and to
return <noError> status.
The snap values are as follow:
<=44 snaps to 44
>=9999 snaps to 9999"
::= { pdl-pcl 16 }
postscript-datecode OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"This indicates the PostScript firmware datecode in
yyyymmdd format.
Additional information:
This object is only supported if PostScript
option is installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no
PostScript option installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no PostScript option
installed."
::= { pdl-postscript 1 }
postscript-resource-saving-memory-size OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or changes the amount of resource saving memory
set aside to hold permanent soft PostScript resources.
Additional information:
Returns the amount of memory, in
bytes, set aside to hold permanent soft PostScript
resources.
This object is only supported if PostScript option
is installed.
Return <noSuchName> status if
attempting to perform a Get on this OID with no
PostScript option installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no PostScript option
installed."
::= { pdl-postscript 2 }
postscript-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains the name of the PDL. For PostScript, the name
is `PostScript'.
Additional information:
This object is only supported if PostScript
option is installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no
PostScript option installed.
Returns an <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no PostScript option
installed."
::= { pdl-postscript 3 }
postscript-version OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains the PDL version.
Additional information:
This object is only supported if PostScript
option is installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no
PostScript option installed.
Returns an <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no PostScript option
installed."
::= { pdl-postscript 4 }
postscript-print-errors OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the value of the print PostScript
errors setting. If eOn, PostScript prints an error page
showing the error encountered and the stack at the time
of the error.
Additional information:
This object is only supported if PostScript
option is installed.
Returns <noSuchName> status if
attempting to perform a Get, or Set on this OID with
no PostScript option installed.
Returns an <noSuchName>
status if attempting to perform an EnableTrap, or
DisableTrap on this OID with no PostScript option
installed."
::= { pdl-postscript 11 }
postscript-jam-recovery OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the PostScript jam recovery setting.
If eOn, then the device will reprint PostScript pages,
if those pages jam.
Additional information:
This object is only supported if PostScript
option is installed.
Returns <noSuchName> status if
attempting to perform a Get, or Set on this OID with
no PostScript option installed.
Returns an <noSuchName>
status if attempting to perform an EnableTrap, or
DisableTrap on this OID with no PostScript option
installed."
::= { pdl-postscript 12 }
esc-p-datecode OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"This indicates the ESC-P PDL datecode. The datecode
format is yyyymmdd.
Additional information:
This object is only supported if ESC-P option is
installed.
Returns an <noSuchName> status if
attempting to perform a Get on this OID with no ESC-P
option installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no ESC-P option
installed."
::= { pdl-esc-p 1 }
esc-p-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains the name of the PDL. For ESC-P, the name is
`ESC-P'.
Additional information:
This object is only supported if ESC-P option is
installed.
Returns an <noSuchName> status if
attempting to perform a Get on this OID with no ESC-P
option installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no ESC-P option
installed."
::= { pdl-esc-p 3 }
esc-p-version OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Contains the PDL version.
Additional information:
This object is only supported if ESC-P option is
installed.
Returns an <noSuchName> status if
attempting to perform a Get on this OID with no ESC-P
option installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no ESC-P option
installed."
::= { pdl-esc-p 4 }
pjl-password OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns PJL password, if the password is not set (zero).
If the password is set, then attempting to retrieve the
password causes an <genErr> to occur
and will return the <NullValue>."
::= { pjl 1 }
not-ready-destination-print-engine OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the print engine sub-system in the device
is not ready. If there are no items in the collection
(i.e. no bits are set), then the print engine sub-
system is ready. If there is an item present, then the
item indicates what is causing the print engine sub-
system to be not ready. cDoorOpen is in the collection
if one or more access panels are open. If the device
contains more than one access panel, then NOT-READY-
PRINT-ENGINE-DOOR indicates which access panel(s) are
open. cInternalMediaJam is in the collection if one or
more pieces of media are jammed inside the device. If
the media is jammed at an input tray, cTrayMediaJam is
in the collection, and if the device has more than one
input tray, then NOT-READY-MEDIA-JAM-AT-TRAY indicates
which tray has a media jam. If the media is jammed at
an output bin, cBinMediaJam is in the collection, and if
the device has more than one output bin, then NOT-READY-
MEDIA-JAM-AT-BIN indicates which bin has a media jam.
cRequestedMediaUnavailable is in the collection if the
current print job requires media that is not available.
cTrayEmpty is in the collection if the current print job
requires media from an input tray that is empty. If the
device has more than one input tray, then NOT-READY-
TRAY-EMPTY indicates which tray is empty.
cOutputBinFull is in the collection if an output bin is
full. If the device has more than one output bin, then
NOT-READY-BIN-FULL indicates which bin is full.
cManualFeedMedia is in the collection if the device is
waiting for media to manually be fed.
cMarkingAgentMissing is in the collection if a marking
agent (toner cartridge, ink pen, etc.) is missing. If
the device has more than one marking agent, then NOT-
READY-MARKING-AGENT-MISSING indicates which marking
agent is missing. cMarkingAgentOut is in the collection
if the device is not ready due to one or more marking
agents being low or out. If the device has more than
one marking agent, then NOT-READY-MARKING-AGENT-LOW-OR-
OUT indicates which marking agent is low or out.
cIncorrectMarkingAgent is in the collection if the
device detects that an incorrect marking agent is
installed. If the device has more than one marking
agent, then NOT-READY-INCORRECT-MARKING-AGENT indicates
which marking agent location is loaded with the wrong
type of marking agent. cTrayMissing is in the
collection if the device is not ready because one or
more trays are not installed. If the device has more
than one input tray, then NOT-READY-TRAY-MISSING
indicates which tray is missing. cDeviceSpecific is in
the collection if one or more items are in either NOT-
READY-LASER-PRINT-ENGINE or NOT-READY-DESTINATION-
INKJET-PRINT-ENGINE-NOT-READY. cMediaPickMisfeed is in
the collection if the print engine detects the tray is
not empty, but can not pick up a sheet of media from
that tray. cMarkingAgentFailure indicates there is a
failure with a marking agent and it may need to be
replaced. If the device supports more than one marking
agent, then the NOT-READY-MARKING-AGENT-FAILURE object
indicates all the marking agents that have failed. The
POS will indicate the marking agent failure recovery
process, if any."
::= { status-prt-eng 1 }
not-ready-laser-print-engine OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if the laser print engine sub-system in the
device is not ready. If there are no items in the
collection (i.e. no bits are set), then the laser print
engine sub-system is ready. If there is an item
present, then the item indicates what is causing the
laser print engine sub-system to be not ready."
::= { status-prt-eng 3 }
total-engine-page-count OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Total number of pages printed by the device. POS
indicates if the total engine page count is kept in
NVRAM, and the maximum supported value before the page
count rolls over to zero.
Additional information:
In LaserJet 4V the total engine page count is kept in
NVRAM however the NVRAM value is only updated every 10
pages. NOTE: The value returned by this OID will be
incremented every page but if power is lost between
NVRAM updates up to 9 pages of the page count may be
lost. The page count counter will be reset to zero
after 16,777,215 (2^24-1) pages."
::= { status-prt-eng 5 }
status-destination-print-engine OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates if part of the print engine sub-system is not
functional, but the non-functional component(s) are not
currently required to print."
::= { status-prt-eng 8 }
default-manual-feed OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eOn(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the default manual feed value used by
the PDLs."
::= { settings-intray 4 }
mp-tray OBJECT-TYPE
SYNTAX INTEGER {
eManual(1),
eCassette(2),
eFirst(3)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or changes the value of the multi-purpose (MP)
tray configuration variable. The MP tray can be
configured to operate as an additional input tray
(eCassette), a manual feed slot (eManual), or in a
manner compatible with the LaserJet III manual feed slot
(eFirst). If configured for eFirst, if media is present
in the MP tray, that media is used (assuming the size
matches and the print job didn't specify another tray)
until the MP tray is empty."
::= { settings-intray 5 }
tray-lock OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns or changes the list of locked input trays. The
printer only pulls media from a locked input tray when
the input tray is specifically requested by the print
job.
Additional information:
When MP-TRAY is eManual or eFirst only
cInTray2Locked or cInTray3Locked can be selected and
cInTray1Locked is illegal. It is also illegal to
select both cInTray2Locked and cInTray3Locked. When
MP-TRAY is eCassette all selections and combinations
of selections are legal."
::= { settings-intray 6 }
not-ready-tray-missing OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates which trays are not currently installed that
is caused the device to be not ready."
::= { status-intray 1 }
not-ready-tray-empty OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates which trays contain no media causing the
device to be not ready. Some devices may treat tray
missing as a tray empty condition."
::= { status-intray 2 }
status-tray-missing OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates which trays are not currently installed that
is caused the device to be in a warning condition."
::= { status-intray 3 }
status-tray-empty OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS optional
DESCRIPTION
"Indicates which trays contain no media causing the
device to be in a warning condition. Some devices may
treat tray missing as a tray empty condition."
::= { status-intray 4 }
tray1-media-size-loaded OBJECT-TYPE
SYNTAX INTEGER {
eUSExecutive(1),
eUSLetter(2),
eUSLegal(3),
eLedger(11),
eISOandJISA4(26),
eISOandJISA3(27),
eJISB5(45),
eJISB4(46),
eJapanesePostcardSingle(71),
eJapanesePostcardDouble(72),
eMonarch(80),
eCommercial10(81),
eInternationalDL(90),
eInternationalC5(91),
eInternationalB5(100),
eCustom(101)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the media size that is currently loaded in tray
#1. This object can be set to indicate the media size
currently loaded, if the printer supports input trays
that can not sense the media size. Complete list of
supported media sizes along with their dimensions are
listed in the ``Media Size Table'' near the end of this
document."
::= { intray1 1 }
tray1-media-available OBJECT-TYPE
SYNTAX INTEGER(-1..100)
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns a number that indicates how full the input tray
is. If the device can only detect empty / not empty the
device returns -1 for not empty and 0 for empty. If the
device can determine how full the tray is, the device
returns a percentage full from 0% to 100%
Additional information:
LaserJet 4V can only detect empty/not empty tray.
It returns -1 for not empty and 0 for empty."
::= { intray1 2 }
tray1-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the device specific name for tray 1."
::= { intray1 3 }
tray2-media-size-loaded OBJECT-TYPE
SYNTAX INTEGER {
eUSLetter(2),
eUSLegal(3),
eLedger(11),
eISOandJISA4(26),
eISOandJISA3(27),
eJISB5(45),
eJISB4(46)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the media size that is currently loaded in tray
#2. Complete list of supported media sizes along with
their dimensions are listed in the ``Media Size Table''
near the end of this document."
::= { intray2 1 }
tray2-media-available OBJECT-TYPE
SYNTAX INTEGER(-1..100)
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns a number that indicates how full the input tray
is. If the device can only detect empty / not empty the
device returns -1 for not empty and 0 for empty. If the
device can determine how full the tray is, the device
returns a percentage full from 0% to 100%
Additional information:
LaserJet 4V can only detect empty/not empty tray.
It returns -1 for not empty and 0 for empty."
::= { intray2 2 }
tray2-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the device specific name for tray 2."
::= { intray2 3 }
tray3-media-size-loaded OBJECT-TYPE
SYNTAX INTEGER {
eUSLetter(2),
eUSLegal(3),
eLedger(11),
eISOandJISA4(26),
eISOandJISA3(27),
eJISB4(46)
}
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the media size that is currently loaded in tray
#3. Complete list of supported media sizes along with
their dimensions are listed in the ``Media Size Table''
near the end of this document.
Additional information:
Those sizes listed in the SYNTAX
section above are the only sizes that are supported
by the LaserJet 4V Optional Lower Cassette (LC).
This object is only supported if a LC is installed.
Returns <noSuchName> status
if attempting to perform a Get on this OID with
no LC installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no LC installed."
::= { intray3 1 }
tray3-media-available OBJECT-TYPE
SYNTAX INTEGER(-1..100)
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns a number that indicates how full the input tray
is. If the device can only detect empty / not empty the
device returns -1 for not empty and 0 for empty. If the
device can determine how full the tray is, the device
returns a percentage full from 0% to 100%
Additional information:
LaserJet 4V can only detect empty/not empty tray.
It returns -1 for not empty and 0 for empty.
This object is only supported if a LC is installed.
Returns <noSuchName> status
if attempting to perform a Get on this OID with
no LC installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no LC installed."
::= { intray3 2 }
tray3-name OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns the device specific name for tray 3.
Additional information:
This object is only supported if a LC is
installed.
Returns <noSuchName> status if
attempting to perform a Get on this OID with no LC
installed.
Returns <noSuchName>
status if attempting to perform a Set, EnableTrap, or
DisableTrap on this OID with no LC installed."
::= { intray3 3 }
outbin1-maximum-capacity OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS optional
DESCRIPTION
"Maximum capacity of the output bin, in sheets of 20
pound paper."
::= { outbin1 1 }
low-marking-agent-processing OBJECT-TYPE
SYNTAX INTEGER {
eStop(1),
eCont(2)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes how the device processes a low
marking agent event. If eCont, then the device
continues to print. If eStop, then the device stops
until a continue event occurs."
::= { settings-marking-agent 3 }
default-ret OBJECT-TYPE
SYNTAX INTEGER {
eOff(1),
eLight(2),
eMedium(3),
eDark(4)
}
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or changes the Resolution Enhancement Technology
setting. Devices that only support eOff and on should
map all other values to on and always return the same
non-eOff value to indicate on. The list of supported
values should be documented in the device POS."
::= { imaging 5 }
default-print-quality OBJECT-TYPE
SYNTAX INTEGER(0..100)
ACCESS read-write
STATUS optional
DESCRIPTION
"Returns or sets the default print quality. A value of
zero has the lowest print quality. A value of 100 has
the highest print quality. Each POS should document
what values in the 0 to 100 range are supported.
Additional information:
Returns or sets the print quality versus cost
trade off. In LaserJet 4V, the supported values are 0
and 100. A value of zero has the lowest print
quality(ECONOMODE=ON), thus minimizes the consumables
used. A value of 100 has the highest print quality
(ECONOMODE=OFF), thus uses more consumables. Setting
to an unsupported value outside of the 0 to 100 range
causes the printer to return
<badValue> status. Setting
to an unsupported value inside of the 0 to 100 range
causes the printer to substitute in a snap value
(listed below) and to return
<noError> status.
The snap values are as follow:
0 to 50 snap to 0
51 to 100 snap to 100"
::= { imaging 7 }
END
View Git Blame Copy Permalink