1529 lines
67 KiB
Plaintext
1529 lines
67 KiB
Plaintext
HP-ICF-RATE-LIMIT-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
|
|
Integer32, Unsigned32
|
|
FROM SNMPv2-SMI
|
|
InterfaceIndex, ifIndex
|
|
FROM IF-MIB
|
|
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
|
|
FROM SNMPv2-CONF
|
|
hpicfObjectModules, hpicfRateLimitTrapsPrefix
|
|
FROM HP-ICF-OID
|
|
;
|
|
|
|
hpicfRateLimitMIB MODULE-IDENTITY
|
|
LAST-UPDATED "201710130000Z" -- October 13, 2017
|
|
ORGANIZATION "HP Networking"
|
|
CONTACT-INFO "Hewlett Packard Company
|
|
8000 Foothills Blvd.
|
|
Roseville, CA 95747"
|
|
DESCRIPTION "This MIB module describes HP rate limit
|
|
information."
|
|
|
|
REVISION "201710130000Z" -- October 13, 2017
|
|
DESCRIPTION "The maximum value of
|
|
hpUnknownUnicastLimitPortSingleControlKbps
|
|
has been modified to 100,000,000."
|
|
|
|
REVISION "201608030000Z" -- August 03, 2016
|
|
DESCRIPTION "The description of below MIBs are modified:
|
|
hpEgressRateLimitPortControlMode,
|
|
hpIngressRateLimitPortControlMode."
|
|
|
|
REVISION "201509040000Z" -- September 04, 2015
|
|
DESCRIPTION "The hpICMPRateLimitPortKbps modified."
|
|
|
|
REVISION "201411181000Z" -- November 18, 2014
|
|
DESCRIPTION "Added egress maximum rate limit objects."
|
|
|
|
REVISION "201411170000Z" -- Nov 17, 2014
|
|
DESCRIPTION "Increased max range value from 10G to 100G for
|
|
hpEgressRateLimitPortSingleControlKbps,
|
|
hpIngressRateLimitPortSingleControlKbps,
|
|
hpIngressBcastLimitPortSingleControlKbps and
|
|
hpIngressMcastLimitPortSingleControlKbps."
|
|
|
|
REVISION "201307110000Z" -- July 11, 2013
|
|
DESCRIPTION "Added hpicfIngressRateLimitVlanConfigTable,
|
|
hpicfRateLimitCompliance3 and
|
|
hpicfIngressRateLimitVlanGroup for limiting ingress
|
|
rate on a VLAN."
|
|
|
|
REVISION "201303121510Z" -- March 12, 2013
|
|
DESCRIPTION "Added kbps-mode rate-limit option for ingress
|
|
unknown-unicast traffic. This is an enhancement
|
|
OID for the unknown-unicast rate-limiting MIB"
|
|
|
|
REVISION "201210051930Z" -- October 5, 2012
|
|
DESCRIPTION "Updated the description of the
|
|
hpBWMinEgressPortPrct object to remove queue
|
|
sum restriction."
|
|
|
|
REVISION "201203121230Z" -- March 12, 2012
|
|
DESCRIPTION "Added the Unknown Unicast Rate-Limiting MIB
|
|
object, which is used by the switch to control
|
|
the unknown unicast traffic."
|
|
|
|
REVISION "201009271130Z" -- September 27, 2010
|
|
DESCRIPTION "Added IPv6 ICMP Rate-Limiting Enhancements through
|
|
the inclusion of IP packet type MIB object."
|
|
|
|
REVISION "201007141610Z" -- July 14, 2010
|
|
DESCRIPTION "Added kbps-mode limit option for ingress Broadcast and
|
|
ingress Multicast rate limiting MIB objects."
|
|
|
|
REVISION "200712041230Z" -- December 4, 2007
|
|
DESCRIPTION "Added ingress Broadcast and ingress Multicast rate
|
|
limiting MIB objects."
|
|
|
|
REVISION "200708291120Z" -- August 29, 2007
|
|
DESCRIPTION "Deprecated all bps objects for
|
|
hpEgressRateLimitPortConfigTable and
|
|
hpIngressRateLimitPortConfigTable, and updated
|
|
compliance information (including correcting ICMP
|
|
group to be hpICMPRateLimitPortConfigGroup2)."
|
|
|
|
REVISION "200707271920Z" -- July 27, 2007
|
|
DESCRIPTION "Modified enumerated type names for
|
|
hpICMPRateLimitPortControlMode object."
|
|
|
|
REVISION "200706011146Z" -- June 1, 2007
|
|
DESCRIPTION "Deprecated hpICMPRateLimitPortState in favor of new
|
|
hpICMPRateLimitPortControlMode object."
|
|
|
|
REVISION "200705301610Z" -- May 30, 2007
|
|
DESCRIPTION "Added Kbps configuration for ICMP, port-egress,
|
|
and port-ingress rate-limiting definitions."
|
|
|
|
REVISION "200607071833Z" -- July 07, 2006
|
|
DESCRIPTION "Added new egress rate limiting bps objects, and
|
|
ingress rate-limiting definitions."
|
|
|
|
REVISION "200504201130Z" -- April 20, 2005
|
|
DESCRIPTION "Added minimum bandwidth and egress rate limiting
|
|
definitions."
|
|
|
|
REVISION "200408221030Z" -- August 22, 2004
|
|
DESCRIPTION "Initial version."
|
|
|
|
::= { hpicfObjectModules 14 }
|
|
|
|
|
|
hpicfRateLimitObjects OBJECT IDENTIFIER ::= { hpicfRateLimitMIB 1 }
|
|
|
|
-- ICMP Rate Limiting Objects
|
|
|
|
hpicfICMPRateLimitObjects OBJECT IDENTIFIER ::= { hpicfRateLimitObjects 1 }
|
|
|
|
hpICMPRateLimitConfig OBJECT IDENTIFIER ::= { hpicfICMPRateLimitObjects 1 }
|
|
|
|
hpICMPRateLimitPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpICMPRateLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains configuration objects on ICMP
|
|
rate limit on a per interface basis."
|
|
::= { hpICMPRateLimitConfig 1 }
|
|
|
|
hpICMPRateLimitPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpICMPRateLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "Entry that contains configuration objects on ICMP
|
|
rate limit on a per interface basis"
|
|
INDEX { hpICMPRateLimitPortConfigIndex }
|
|
::= { hpICMPRateLimitPortConfigTable 1 }
|
|
|
|
HpICMPRateLimitPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpICMPRateLimitPortConfigIndex InterfaceIndex,
|
|
hpICMPRateLimitPortState INTEGER,
|
|
hpICMPRateLimitPortPrct Integer32,
|
|
hpICMPRateLimitPortAlarmFlag INTEGER,
|
|
hpICMPRateLimitPortKbps Integer32,
|
|
hpICMPRateLimitPortControlMode INTEGER,
|
|
hpICMPRateLimitPortIpPacketType INTEGER
|
|
}
|
|
|
|
hpICMPRateLimitPortConfigIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The interface index associated with this entry."
|
|
::= { hpICMPRateLimitPortConfigEntry 1 }
|
|
|
|
hpICMPRateLimitPortState OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
enabled(1),
|
|
disabled(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "This object indicates whether ICMP rate limiting is
|
|
enabled on the corresponding port.
|
|
|
|
Because this is a State object it cannot distinguish
|
|
between percent-based ICMP Rate-Limiting and the newer
|
|
Kbps-based ICMP Rate-Limiting. Therefore, it has been
|
|
deprecated in favor of hpICMPRateLimitPortControlMode."
|
|
DEFVAL { disabled }
|
|
::= { hpICMPRateLimitPortConfigEntry 2 }
|
|
|
|
hpICMPRateLimitPortPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This indicates the percent of ICMP rate limit on
|
|
the port. The value of this object must be
|
|
interpreted under the context of
|
|
hpICMPRateLimitPortState. A value of 0 is not the
|
|
same as disabling, but rather all ICMP traffic must
|
|
be dropped."
|
|
::= { hpICMPRateLimitPortConfigEntry 3 }
|
|
|
|
hpICMPRateLimitPortAlarmFlag OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
clear(1),
|
|
set(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This object indicates whether ICMP rate limiting
|
|
alarm has been sent. When an alarm is sent, this
|
|
object is set to set(2). Once a management station
|
|
changes this object to clear(1), an alarm can be
|
|
sent again for this port."
|
|
DEFVAL { clear }
|
|
::= { hpICMPRateLimitPortConfigEntry 4 }
|
|
|
|
|
|
hpICMPRateLimitPortKbps OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The maximum Kilobits-per-second of ICMP traffic that may
|
|
be received inbound on the port. The value of this
|
|
object must be interpreted under the context of
|
|
hpICMPRateLimitControlMode. A value of 0 is not the
|
|
same as disabling, but means instead that all ICMP
|
|
traffic must be dropped."
|
|
::= { hpICMPRateLimitPortConfigEntry 5 }
|
|
|
|
hpICMPRateLimitPortControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
portPrct(2),
|
|
portKbps(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The mode by which inbound ICMP traffic on this port will
|
|
Rate-Limited. If icmpRateLimitPerPortOnly is configured,
|
|
there will be a single maximum percentage-based rate for
|
|
the entire port. If icmpRateLimitPerPortOnlyKbpsMode is
|
|
configured, there will be a single maximum kilobits-per-
|
|
second rate for the entire port. When ICMP rate-limiting
|
|
is disabled, there are no maximum controls on inbound
|
|
ICMP traffic for this port."
|
|
DEFVAL { disabled }
|
|
::= { hpICMPRateLimitPortConfigEntry 6 }
|
|
|
|
hpICMPRateLimitPortIpPacketType OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
ipv4PacketsOnly(1),
|
|
ipv6PacketsOnly(2),
|
|
ipv4AndIpv6Packets(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "This object represents the type(s) of IP packet to which
|
|
the specified ICMP rate-limit will be applied. The
|
|
default is IPv4."
|
|
DEFVAL { ipv4PacketsOnly }
|
|
::= { hpICMPRateLimitPortConfigEntry 7 }
|
|
|
|
|
|
hpICMPRateLimitPortNotification NOTIFICATION-TYPE
|
|
OBJECTS { hpICMPRateLimitNotifyPortIndex }
|
|
STATUS current
|
|
DESCRIPTION "This notification indicates limit has exceeded."
|
|
|
|
::= { hpicfRateLimitTrapsPrefix 1 }
|
|
|
|
hpICMPRateLimitNotifyPortIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS accessible-for-notify
|
|
STATUS current
|
|
DESCRIPTION "The interface index associated with
|
|
hpICMPRateLimitPortNotification event."
|
|
::= { hpicfICMPRateLimitObjects 2 }
|
|
|
|
-- Egress Minimum Bandwidth Ojbects
|
|
|
|
hpicfBWMinEgressObjects OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitObjects 2 }
|
|
hpBWMinEgressPortConfig OBJECT IDENTIFIER ::=
|
|
{ hpicfBWMinEgressObjects 1 }
|
|
|
|
hpBWMinEgressPortNumQueues OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION "The number of bandwidth minimum egress queues supported
|
|
on this system."
|
|
::= { hpBWMinEgressPortConfig 1 }
|
|
|
|
hpBWMinEgressPortPrctTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpBWMinEgressPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port's egress
|
|
Guaranteed Minimum Bandwidth percent configurations on
|
|
this switch. The number of entries in this table is
|
|
determined by hpBWMinEgressPortNumQueues. The priority of
|
|
the queues is in ascending order, starting with queue one
|
|
being the lowest and queue hpBWMinEgressPortNumQueues
|
|
being the highest."
|
|
::= { hpBWMinEgressPortConfig 2 }
|
|
|
|
hpBWMinEgressPortPrctEntry OBJECT-TYPE
|
|
SYNTAX HpBWMinEgressPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's egress
|
|
Guaranteed Minimum Bandwidth percent configuration."
|
|
INDEX { ifIndex, hpBWMinEgressPortPrctQueue }
|
|
::= { hpBWMinEgressPortPrctTable 1 }
|
|
|
|
HpBWMinEgressPortPrctEntry ::=
|
|
SEQUENCE {
|
|
hpBWMinEgressPortPrctQueue Integer32,
|
|
hpBWMinEgressPortPrct Integer32
|
|
}
|
|
|
|
hpBWMinEgressPortPrctQueue OBJECT-TYPE
|
|
SYNTAX Integer32 (1..9000)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The queue associated with this entry. The priority of
|
|
the queues is in ascending order, starting with queue one
|
|
being the lowest and queue hpBWMinEgressPortNumQueues
|
|
being the highest."
|
|
::= { hpBWMinEgressPortPrctEntry 1 }
|
|
|
|
hpBWMinEgressPortPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The percentage of Guaranteed Minimum bandwidth to be
|
|
assigned to this egress queue for this port. Total values
|
|
for all queues must not exceed 100 percent."
|
|
::= { hpBWMinEgressPortPrctEntry 2 }
|
|
|
|
-- Ingress Minimum Bandwidth Objects
|
|
|
|
hpicfBWMinIngressObjects OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitObjects 3 }
|
|
hpBWMinIngressPortConfig OBJECT IDENTIFIER ::=
|
|
{ hpicfBWMinIngressObjects 1 }
|
|
|
|
hpBWMinIngressPortNumQueues OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION "The number of bandwidth minimum ingress queues supported
|
|
on this system."
|
|
::= { hpBWMinIngressPortConfig 1 }
|
|
|
|
hpBWMinIngressPortPrctTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpBWMinIngressPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port's
|
|
ingress Guaranteed Minimum Bandwidth percent
|
|
configurations on this switch. The number of entries in
|
|
this table is determined by hpBWMinIngressPortNumQueues.
|
|
The priority of the queues is in ascending order, starting
|
|
with queue one being the lowest and queue
|
|
hpBWMinIngressPortNumQueues being the highest."
|
|
::= { hpBWMinIngressPortConfig 2 }
|
|
|
|
hpBWMinIngressPortPrctEntry OBJECT-TYPE
|
|
SYNTAX HpBWMinIngressPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's ingress
|
|
Guaranteed Minimum Bandwidth percent configuration."
|
|
INDEX { ifIndex, hpBWMinIngressPortPrctQueue }
|
|
::= { hpBWMinIngressPortPrctTable 1 }
|
|
|
|
HpBWMinIngressPortPrctEntry ::=
|
|
SEQUENCE {
|
|
hpBWMinIngressPortPrctQueue Integer32,
|
|
hpBWMinIngressPortPrct Integer32
|
|
}
|
|
|
|
hpBWMinIngressPortPrctQueue OBJECT-TYPE
|
|
SYNTAX Integer32 (1..9000)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The queue associated with this entry. The priority of
|
|
the queues is in ascending order, starting with queue one
|
|
being the lowest and queue hpBWMinIngressPortNumQueues
|
|
being the highest."
|
|
::= { hpBWMinIngressPortPrctEntry 1 }
|
|
|
|
hpBWMinIngressPortPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The percentage of Guaranteed Minimum bandwidth to be
|
|
assigned to this ingress queue for this port. Total values
|
|
for all queues must not exceed 100 percent."
|
|
::= { hpBWMinIngressPortPrctEntry 2 }
|
|
|
|
-- Egress Rate Limiting Objects
|
|
|
|
hpicfRateLimitPortObjects OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitObjects 4 }
|
|
hpRateLimitPortConfig OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitPortObjects 1 }
|
|
|
|
hpEgressRateLimitPortNumQueues OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION "The number of egress rate-limiting queues supported on
|
|
this system."
|
|
::= { hpRateLimitPortConfig 1 }
|
|
|
|
hpEgressRateLimitPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpEgressRateLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port egress
|
|
Rate-Limiting configurations on this switch."
|
|
::= { hpRateLimitPortConfig 2 }
|
|
|
|
hpEgressRateLimitPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpEgressRateLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's egress
|
|
Rate-Limiting configuration."
|
|
INDEX { hpEgressRateLimitPortIndex }
|
|
::= { hpEgressRateLimitPortConfigTable 1 }
|
|
|
|
HpEgressRateLimitPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpEgressRateLimitPortIndex InterfaceIndex,
|
|
hpEgressRateLimitPortControlMode INTEGER,
|
|
hpEgressRateLimitPortSingleControlPrct Integer32,
|
|
hpEgressRateLimitPortSingleControlBps Unsigned32,
|
|
hpEgressRateLimitPortSingleControlKbps Integer32,
|
|
hpEgressRateLimitPortQueueControlMode INTEGER
|
|
}
|
|
|
|
hpEgressRateLimitPortIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row in the
|
|
Interfaces Table."
|
|
::= { hpEgressRateLimitPortConfigEntry 1 }
|
|
|
|
hpEgressRateLimitPortControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
egressRateLimitPerPortOnly(2),
|
|
egressRateLimitPerQueue(3),
|
|
egressRateLimitPerPortOnlyBpsMode(4),
|
|
egressRateLimitPerQueueBpsMode(5),
|
|
egressRateLimitPerPortOnlyKbpsMode(6)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The mode by which this port will be Rate-Limited on
|
|
egress. If egressRateLimitPerPortOnly is configured, there
|
|
will be a single maximum percentage-based rate for the
|
|
entire port. If egressRateLimitPerQueue is configured, the
|
|
values for each of the queues indicate the maximum
|
|
percentage of port traffic that may be transmitted by that
|
|
queue. If egressRateLimitPerPortOnlyKbpsMode is
|
|
configured, there will be a single maximum
|
|
kilobits-per-second rate for the entire port. The queues
|
|
are defined under hpEgressRateLimitPortPrctTable. When egress
|
|
rate-limiting is disabled, there are no maximum controls
|
|
on egress for this port.
|
|
NOTE : Currently, egressRateLimitPerPortOnlyBpsMode and
|
|
egressRateLimitPerQueueBpsMode are not supported."
|
|
DEFVAL { disabled }
|
|
::= { hpEgressRateLimitPortConfigEntry 2 }
|
|
|
|
hpEgressRateLimitPortSingleControlPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpEgressRateLimitPortControlMode is configured
|
|
for egressRateLimitPerPortOnly, this value is the maximum
|
|
percentage of traffic that may be transmitted by this
|
|
port on egress."
|
|
::= { hpEgressRateLimitPortConfigEntry 3 }
|
|
|
|
hpEgressRateLimitPortSingleControlBps OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4200000000)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "When hpEgressRateLimitPortControlMode is configured for
|
|
egressRateLimitPerPortOnlyBpsMode, this value is the
|
|
maximum bits-per-second of traffic that may be transmitted
|
|
by this port on egress."
|
|
::= { hpEgressRateLimitPortConfigEntry 4 }
|
|
|
|
hpEgressRateLimitPortSingleControlKbps OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpEgressRateLimitPortControlMode is configured for
|
|
egressRateLimitPerPortOnlyKbpsMode, this value is the
|
|
maximum kilobits-per-second of traffic that may be
|
|
transmitted by this port on egress."
|
|
::= { hpEgressRateLimitPortConfigEntry 5 }
|
|
|
|
hpEgressRateLimitPortQueueControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
egressRateLimitQueuePrctMode(2),
|
|
egressRateLimitQueueKbpsMode(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The mode by which queues on this port will be rate-limited
|
|
on egress. If egressRateLimitQueuePrctMode is configured,
|
|
the values for each of the queues indicate the maximum
|
|
percentage of port traffic that may be transmitted by that
|
|
queue.If egressRateLimitQueueKbpsMode is configured, the
|
|
maximum transmission-rate values for each of the queues will
|
|
be expressed in kilobits-per-second. The queues are defined
|
|
under hpEgressRateLimitPortQueueTable. When egress
|
|
rate-limiting is disabled, there are no maximum controls on
|
|
egress for this port."
|
|
DEFVAL { disabled }
|
|
::= { hpEgressRateLimitPortConfigEntry 6 }
|
|
|
|
hpEgressRateLimitPortPrctTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpEgressRateLimitPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port egress
|
|
Rate-Limiting percent configurations on this switch. The
|
|
number of entries in this table is determined by
|
|
hpEgressRateLimitPortNumQueues. The priority of the
|
|
queues is in ascending order, starting with queue one
|
|
being the lowest priority and queue
|
|
hpEgressRateLimitPortNumQueues being the highest
|
|
priority."
|
|
::= { hpRateLimitPortConfig 3 }
|
|
|
|
hpEgressRateLimitPortPrctEntry OBJECT-TYPE
|
|
SYNTAX HpEgressRateLimitPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's egress
|
|
Rate-Limiting percent configuration."
|
|
INDEX { hpEgressRateLimitPortIndex,
|
|
hpEgressRateLimitPortPrctQueue }
|
|
::= { hpEgressRateLimitPortPrctTable 1 }
|
|
|
|
HpEgressRateLimitPortPrctEntry ::=
|
|
SEQUENCE {
|
|
hpEgressRateLimitPortPrctQueue Integer32,
|
|
hpEgressRateLimitPortPrct Integer32
|
|
}
|
|
|
|
hpEgressRateLimitPortPrctQueue OBJECT-TYPE
|
|
SYNTAX Integer32 (1..9000)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The queue associated with this entry. The priority o
|
|
of the queues is in ascending order, starting with
|
|
queue one being the lowest and queue
|
|
hpEgressRateLimitgressPortNumQueues being the highest."
|
|
::= { hpEgressRateLimitPortPrctEntry 1 }
|
|
|
|
hpEgressRateLimitPortPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The maximum percentage of traffic that may be
|
|
transmitted by this port's queue on egress.
|
|
hpEgressRateLimitPortControlMode must be configured to
|
|
use egressRateLimitPerQueue for this to take effect. A
|
|
value of 0-percent for any queue means that no traffic
|
|
will ever be transmitted on this port for that egress
|
|
queue."
|
|
::= { hpEgressRateLimitPortPrctEntry 2 }
|
|
|
|
hpEgressRateLimitPortBpsTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpEgressRateLimitPortBpsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "A table that contains information about the port
|
|
egress Rate-Limiting bits-per-second configurations on this
|
|
switch. The number of entries in this table is determined
|
|
by hpEgressRateLimitPortNumQueues. The priority of the
|
|
queues is in ascending order, starting with queue one
|
|
being the lowest priority and queue
|
|
hpEgressRateLimitPortNumQueues being the highest
|
|
priority queue."
|
|
::= { hpRateLimitPortConfig 4 }
|
|
|
|
hpEgressRateLimitPortBpsEntry OBJECT-TYPE
|
|
SYNTAX HpEgressRateLimitPortBpsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "The information associated with each port's egress
|
|
Rate-Limiting bits-per-second configuration."
|
|
INDEX { hpEgressRateLimitPortIndex,
|
|
hpEgressRateLimitPortBpsQueue }
|
|
::= { hpEgressRateLimitPortBpsTable 1 }
|
|
|
|
HpEgressRateLimitPortBpsEntry ::=
|
|
SEQUENCE {
|
|
hpEgressRateLimitPortBpsQueue Integer32,
|
|
hpEgressRateLimitPortBps Unsigned32
|
|
}
|
|
|
|
|
|
hpEgressRateLimitPortBpsQueue OBJECT-TYPE
|
|
SYNTAX Integer32 (1..64)
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "The queue associated with this entry. The priority of
|
|
the queues is in ascending order, starting with queue one
|
|
being the lowest and queue
|
|
hpEgressRateLimitgressPortNumQueues being the highest."
|
|
::= { hpEgressRateLimitPortBpsEntry 1 }
|
|
|
|
hpEgressRateLimitPortBps OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4200000000)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "The maximum bits-per-second of traffic that may be
|
|
transmitted by this port's queue on egress.
|
|
hpEgressRateLimitPortControlMode must be configured to use
|
|
egressRateLimitPerQueue for this to take effect. A value
|
|
of 0-percent for any queue means that no traffic will ever
|
|
be transmitted on this port for that egress queue. The
|
|
values for each queue must not exceed the bits-per-second
|
|
capability of the current network link speed."
|
|
::= { hpEgressRateLimitPortBpsEntry 2 }
|
|
|
|
hpEgressRateLimitPortQueueConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpEgressRateLimitPortQueueConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port egress-
|
|
queue rate-limiting configurations on this switch."
|
|
::= { hpRateLimitPortConfig 5 }
|
|
|
|
hpEgressRateLimitPortQueueConfigEntry OBJECT-TYPE
|
|
SYNTAX HpEgressRateLimitPortQueueConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with the egress
|
|
rate-limiting configuration for the queues on each port."
|
|
INDEX { hpEgressRateLimitPortIndex,
|
|
hpEgressRateLimitPortQueueIndex }
|
|
::= { hpEgressRateLimitPortQueueConfigTable 1 }
|
|
|
|
HpEgressRateLimitPortQueueConfigEntry ::=
|
|
SEQUENCE {
|
|
hpEgressRateLimitPortQueueIndex Integer32,
|
|
hpEgressRateLimitPortQueueMax Integer32
|
|
}
|
|
|
|
hpEgressRateLimitPortQueueIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..9000)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The queue associated with this entry. The priority
|
|
of the queues is in ascending order, starting with
|
|
queue one being the lowest and queue
|
|
hpEgressRateLimitEgressPortNumQueues being the highest."
|
|
::= { hpEgressRateLimitPortQueueConfigEntry 1 }
|
|
|
|
hpEgressRateLimitPortQueueMax OBJECT-TYPE
|
|
SYNTAX Integer32 (0.. 100000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The maximum amount of traffic that may be transmitted
|
|
by this port's corresponding queue on egress.
|
|
When the value of hpEgressRateLimitPortQueueControlMode
|
|
is egressRateLimitQueuePrctMode, this maximum value is a
|
|
percentage. A limit of 100% acts as no limit.
|
|
A value of 0-percent for any queue means that no traffic
|
|
will ever be transmitted on this port for that egress
|
|
queue. When the value of
|
|
hpEgressRateLimitPortQueueControlMode is
|
|
egressRateLimitQueueKbpsMode, this maximum value is in
|
|
kilobits-per-second. A limit of kbps which matches the
|
|
port's maximum media speed acts as no limit."
|
|
::= { hpEgressRateLimitPortQueueConfigEntry 2 }
|
|
|
|
-- Ingress Rate Limiting Objects
|
|
|
|
hpicfIngressRateLimitPortObjects OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitObjects 5 }
|
|
hpRateLimitIngressPortConfig OBJECT IDENTIFIER ::=
|
|
{ hpicfIngressRateLimitPortObjects 1 }
|
|
|
|
|
|
hpIngressRateLimitPortNumQueues OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION "The number of ingress rate-limiting queues supported on
|
|
this system."
|
|
::= { hpRateLimitIngressPortConfig 1 }
|
|
|
|
hpIngressRateLimitPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpIngressRateLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port ingress
|
|
Rate-Limiting configurations on this switch."
|
|
::= { hpRateLimitIngressPortConfig 2 }
|
|
|
|
hpIngressRateLimitPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpIngressRateLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's ingress
|
|
Rate-Limiting configuration."
|
|
INDEX { hpIngressRateLimitPortIndex }
|
|
::= { hpIngressRateLimitPortConfigTable 1 }
|
|
|
|
HpIngressRateLimitPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpIngressRateLimitPortIndex InterfaceIndex,
|
|
hpIngressRateLimitPortControlMode INTEGER,
|
|
hpIngressRateLimitPortSingleControlPrct Integer32,
|
|
hpIngressRateLimitPortSingleControlBps Unsigned32,
|
|
hpIngressRateLimitPortSingleControlKbps Integer32
|
|
}
|
|
|
|
hpIngressRateLimitPortIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row in the
|
|
Interfaces Table."
|
|
::= { hpIngressRateLimitPortConfigEntry 1 }
|
|
|
|
hpIngressRateLimitPortControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
ingressRateLimitPerPortOnly(2),
|
|
ingressRateLimitPerQueue(3),
|
|
ingressRateLimitPerPortOnlyBpsMode(4),
|
|
ingressRateLimitPerQueueBpsMode(5),
|
|
ingressRateLimitPerPortOnlyKbpsMode(6)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The mode by which this port will be Rate-Limited on
|
|
ingress. If ingressRateLimitPerPortOnly is configured,
|
|
there will be a single maximum percentage-based rate for
|
|
the entire port. If ingressRateLimitPerQueue is
|
|
configured, the values for each of the queues indicate the
|
|
maximum percentage of port traffic that may be transmitted
|
|
by that queue. If ingressRateLimitPerPortOnlyKbpsMode is
|
|
configured, there will be a single maximum kilobits-per-second
|
|
rate for the entire port. The queues are defined under
|
|
hpIngressRateLimitPortPrctTable. When ingress rate-limiting
|
|
is disabled, there are no maximum controls on ingress for this port.
|
|
NOTE : Currently, IngressRateLimitPerPortOnlyBpsMode and
|
|
ingressRateLimitPerQueueBpsMode are not supported."
|
|
DEFVAL { disabled }
|
|
::= { hpIngressRateLimitPortConfigEntry 2 }
|
|
|
|
hpIngressRateLimitPortSingleControlPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpIngressRateLimitPortControlMode is configured
|
|
for ingressRateLimitPerPortOnly, this value is the maximum
|
|
percentage of traffic that may be transmitted by this
|
|
port on egress."
|
|
::= { hpIngressRateLimitPortConfigEntry 3 }
|
|
|
|
hpIngressRateLimitPortSingleControlBps OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4200000000)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "When hpIngressRateLimitPortControlMode is configured for
|
|
ingressRateLimitPerPortOnlyBpsMode, this value is the
|
|
maximum bits-per-second of traffic that may be transmitted
|
|
by this port on ingress."
|
|
::= { hpIngressRateLimitPortConfigEntry 4}
|
|
|
|
hpIngressRateLimitPortSingleControlKbps OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpIngressRateLimitPortControlMode is configured for
|
|
ingressRateLimitPerPortOnlyKbpsMode, this value is the
|
|
maximum kilobits-per-second of traffic that may be
|
|
transmitted by this port on ingress."
|
|
::= { hpIngressRateLimitPortConfigEntry 5}
|
|
|
|
hpIngressRateLimitPortPrctTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpIngressRateLimitPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port ingress
|
|
Rate-Limiting percent configurations on this switch. The
|
|
number of entries in this table is determined by
|
|
hpIngressRateLimitPortNumQueues. The priority of the
|
|
queues is in ascending order, starting with queue one
|
|
being the lowest priority and queue
|
|
hpIngressRateLimitPortNumQueues being the highest
|
|
priority."
|
|
::= { hpRateLimitIngressPortConfig 3 }
|
|
|
|
hpIngressRateLimitPortPrctEntry OBJECT-TYPE
|
|
SYNTAX HpIngressRateLimitPortPrctEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's ingress
|
|
Rate-Limiting percent configuration."
|
|
INDEX { hpIngressRateLimitPortIndex,
|
|
hpIngressRateLimitPortPrctQueue }
|
|
::= { hpIngressRateLimitPortPrctTable 1 }
|
|
|
|
HpIngressRateLimitPortPrctEntry ::=
|
|
SEQUENCE {
|
|
hpIngressRateLimitPortPrctQueue Integer32,
|
|
hpIngressRateLimitPortPrct Integer32
|
|
}
|
|
|
|
hpIngressRateLimitPortPrctQueue OBJECT-TYPE
|
|
SYNTAX Integer32 (1..9000)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The queue associated with this entry. The priority
|
|
of the queues is in ascending order, starting with
|
|
queue one being the lowest and queue
|
|
hpIngressRateLimitgressPortNumQueues being the highest."
|
|
::= { hpIngressRateLimitPortPrctEntry 1 }
|
|
|
|
hpIngressRateLimitPortPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The maximum percentage of traffic that may be
|
|
transmitted by this port's queue on ingress.
|
|
hpIngressRateLimitPortControlMode must be configured to
|
|
use ingressRateLimitPerQueue for this to take effect. A
|
|
value of 0-percent for any queue means that no traffic
|
|
will ever be transmitted on this port for that ingress
|
|
queue. The values for each queue must not exceed 100
|
|
percent."
|
|
::= { hpIngressRateLimitPortPrctEntry 2 }
|
|
|
|
hpIngressRateLimitPortBpsTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpIngressRateLimitPortBpsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "A table that contains information about the port ingress
|
|
Rate-Limiting bits-per-second configurations on this
|
|
switch. The number of entries in this table is determined
|
|
by hpIngressRateLimitPortNumQueues. The priority of the
|
|
queues is in ascending order, starting with queue one
|
|
being the lowest priority and queue
|
|
hpIngressRateLimitPortNumQueues being the highest
|
|
priority queue."
|
|
::= { hpRateLimitIngressPortConfig 4 }
|
|
|
|
hpIngressRateLimitPortBpsEntry OBJECT-TYPE
|
|
SYNTAX HpIngressRateLimitPortBpsEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "The information associated with each port's egress
|
|
Rate-Limiting bits-per-second configuration."
|
|
INDEX { hpIngressRateLimitPortIndex,
|
|
hpIngressRateLimitPortBpsQueue }
|
|
::= { hpIngressRateLimitPortBpsTable 1 }
|
|
|
|
HpIngressRateLimitPortBpsEntry ::=
|
|
SEQUENCE {
|
|
hpIngressRateLimitPortBpsQueue Integer32,
|
|
hpIngressRateLimitPortBps Unsigned32
|
|
}
|
|
|
|
hpIngressRateLimitPortBpsQueue OBJECT-TYPE
|
|
SYNTAX Integer32 (1..64)
|
|
MAX-ACCESS not-accessible
|
|
STATUS deprecated
|
|
DESCRIPTION "The queue associated with this entry. The priority of
|
|
the queues is in ascending order, starting with queue one
|
|
being the lowest and queue
|
|
hpIngressRateLimitgressPortNumQueues being the highest."
|
|
::= { hpIngressRateLimitPortBpsEntry 1 }
|
|
|
|
hpIngressRateLimitPortBps OBJECT-TYPE
|
|
SYNTAX Unsigned32 (0..4200000000)
|
|
MAX-ACCESS read-write
|
|
STATUS deprecated
|
|
DESCRIPTION "The maximum bits-per-second of traffic that may be
|
|
transmitted by this port's queue on ingress.
|
|
hpIngressRateLimitPortControlMode must be configured to
|
|
use ingressRateLimitPerQueue for this to take effect. A
|
|
value of 0-percent for any queue means that no traffic
|
|
will ever be transmitted on this port for that ingress
|
|
queue. The values for each queue must not exceed the
|
|
bits-per-second capability of the current network link
|
|
speed."
|
|
::= { hpIngressRateLimitPortBpsEntry 2 }
|
|
|
|
|
|
-- Ingress Broadcast Limiting Objects
|
|
|
|
hpicfIngressBcastLimitPortObjects OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitObjects 6 }
|
|
hpBcastLimitIngressPortConfig OBJECT IDENTIFIER ::=
|
|
{ hpicfIngressBcastLimitPortObjects 1 }
|
|
|
|
hpIngressBcastLimitPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpIngressBcastLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port ingress
|
|
Broadcast-Limiting configurations on this switch."
|
|
::= { hpBcastLimitIngressPortConfig 1 }
|
|
|
|
hpIngressBcastLimitPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpIngressBcastLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's ingress
|
|
Broadcast-Limiting configuration."
|
|
INDEX { hpIngressBcastLimitPortIndex }
|
|
::= { hpIngressBcastLimitPortConfigTable 1 }
|
|
|
|
HpIngressBcastLimitPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpIngressBcastLimitPortIndex InterfaceIndex,
|
|
hpIngressBcastLimitPortControlMode INTEGER,
|
|
hpIngressBcastLimitPortSingleControlPrct Integer32,
|
|
hpIngressBcastLimitPortSingleControlKbps Integer32
|
|
}
|
|
|
|
hpIngressBcastLimitPortIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row in the
|
|
Interfaces Table."
|
|
::= { hpIngressBcastLimitPortConfigEntry 1 }
|
|
|
|
hpIngressBcastLimitPortControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
ingressBcastLimitPerPortOnly(2),
|
|
ingressBcastLimitPerPortOnlyKbpsMode(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The mode by which this port will be Broadcast-Limited on
|
|
ingress. If ingressBcastLimitPerPortOnly is configured,
|
|
there will be a single maximum percentage-based broadcast
|
|
traffic limit for the entire port. If
|
|
ingressBcastLimitPerPortOnlyKbpsMode is configured, there
|
|
will be a single maximum kilobits-per-second maximum
|
|
broadcast traffic rate for the entire port. When ingress
|
|
Broadcast-limiting is disabled, there are no maximum
|
|
broadcast traffic controls on ingress for this port."
|
|
DEFVAL { disabled }
|
|
::= { hpIngressBcastLimitPortConfigEntry 2 }
|
|
|
|
hpIngressBcastLimitPortSingleControlPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpIngressBcastLimitPortControlMode is configured
|
|
for ingressBcastLimitPerPortOnly, this value is the maximum
|
|
percentage of traffic that may be transmitted by
|
|
this port on ingress."
|
|
::= { hpIngressBcastLimitPortConfigEntry 3 }
|
|
|
|
hpIngressBcastLimitPortSingleControlKbps OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpIngressBcastLimitPortControlMode is configured for
|
|
ingressBcastLimitPerPortOnlyKbpsMode, this value is the
|
|
maximum kilobits-per-second of broadcast traffic that may be
|
|
transmitted by this port on ingress."
|
|
::= { hpIngressBcastLimitPortConfigEntry 4}
|
|
|
|
-- Ingress Multicast Limiting Objects
|
|
|
|
hpicfIngressMcastLimitPortObjects OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitObjects 7 }
|
|
hpMcastLimitIngressPortConfig OBJECT IDENTIFIER ::=
|
|
{ hpicfIngressMcastLimitPortObjects 1 }
|
|
|
|
hpIngressMcastLimitPortConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpIngressMcastLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the port ingress
|
|
Multicast-Limiting configurations on this switch."
|
|
::= { hpMcastLimitIngressPortConfig 1 }
|
|
|
|
hpIngressMcastLimitPortConfigEntry OBJECT-TYPE
|
|
SYNTAX HpIngressMcastLimitPortConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's ingress
|
|
Multicast-Limiting configuration."
|
|
INDEX { hpIngressMcastLimitPortIndex }
|
|
::= { hpIngressMcastLimitPortConfigTable 1 }
|
|
|
|
HpIngressMcastLimitPortConfigEntry ::=
|
|
SEQUENCE {
|
|
hpIngressMcastLimitPortIndex InterfaceIndex,
|
|
hpIngressMcastLimitPortControlMode INTEGER,
|
|
hpIngressMcastLimitPortSingleControlPrct Integer32,
|
|
hpIngressMcastLimitPortSingleControlKbps Integer32
|
|
}
|
|
|
|
hpIngressMcastLimitPortIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row in the
|
|
Interfaces Table."
|
|
::= { hpIngressMcastLimitPortConfigEntry 1 }
|
|
|
|
hpIngressMcastLimitPortControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
ingressMcastLimitPerPortOnly(2),
|
|
ingressMcastLimitPerPortOnlyKbpsMode(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The mode by which this port will be Multicast-Limited on
|
|
ingress. If ingressMcastLimitPerPortOnly is configured,
|
|
there will be a single maximum percentage-based multicast
|
|
traffic limit for the entire port. If
|
|
ingressMcastLimitPerPortOnlyKbpsMode is configured, there
|
|
will be a single maximum kilobits-per-second maximum
|
|
multicast traffic rate for the entire port. When ingress
|
|
Multicast-limiting is disabled, there are no maximum
|
|
multicast traffic controls on ingress for this port."
|
|
DEFVAL { disabled }
|
|
::= { hpIngressMcastLimitPortConfigEntry 2 }
|
|
|
|
hpIngressMcastLimitPortSingleControlPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpIngressMcastLimitPortControlMode is configured
|
|
for ingressMcastLimitPerPortOnly, this value is the maximum
|
|
percentage of multicast traffic that may be transmitted
|
|
by this port on ingress."
|
|
::= { hpIngressMcastLimitPortConfigEntry 3 }
|
|
|
|
hpIngressMcastLimitPortSingleControlKbps OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "When hpIngressMcastLimitPortControlMode is configured
|
|
for ingressMcastLimitPerPortOnlyKbpsMode, this value is the
|
|
maximum kilobits-per-second of multicast traffic that may be
|
|
transmitted by this port on ingress."
|
|
::= { hpIngressMcastLimitPortConfigEntry 4}
|
|
|
|
-- Unknown Unicast Rate Limiting Objects
|
|
|
|
hpicfUnknownUnicastLimitPortObjects OBJECT IDENTIFIER ::=
|
|
{ hpicfRateLimitObjects 8 }
|
|
hpUnknownUnicastLimitPortConfig OBJECT IDENTIFIER ::=
|
|
{ hpicfUnknownUnicastLimitPortObjects 1 }
|
|
|
|
hpUnknownUnicastLimitConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpUnknownUnicastLimitConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table that contains information about the
|
|
unknown-unicast rate limiting configurations
|
|
on this switch."
|
|
::= { hpUnknownUnicastLimitPortConfig 1 }
|
|
|
|
hpUnknownUnicastLimitConfigEntry OBJECT-TYPE
|
|
SYNTAX HpUnknownUnicastLimitConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The information associated with each port's
|
|
unknown-unicast rate limiting configuration."
|
|
INDEX { hpUnknownUnicastLimitPortIndex }
|
|
::= { hpUnknownUnicastLimitConfigTable 1 }
|
|
|
|
HpUnknownUnicastLimitConfigEntry ::=
|
|
SEQUENCE {
|
|
hpUnknownUnicastLimitPortIndex InterfaceIndex,
|
|
hpUnknownUnicastLimitPortControlMode INTEGER,
|
|
hpUnknownUnicastLimitPortSingleControlPrct Integer32,
|
|
hpUnknownUnicastLimitPortSingleControlKbps Integer32
|
|
}
|
|
|
|
hpUnknownUnicastLimitPortIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The ifIndex value which uniquely identifies a row
|
|
in the interfaces table."
|
|
::= { hpUnknownUnicastLimitConfigEntry 1 }
|
|
|
|
hpUnknownUnicastLimitPortControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
disabled(1),
|
|
unknownUnicastLimitPerPortOnly(2),
|
|
unknownUnicastLimitPerPortOnlyKbpsMode(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The mode by which unknown-unicast ingress traffic on this port
|
|
will be rate limited. If unknownUnicastLimitPerPortOnly is
|
|
configured, the limit will be a percentage of the current line
|
|
rate of the port. The percentage is specified in
|
|
hpUnknownUnicastLimitPortSingleControlPrct. If
|
|
unknownUnicastLimitPerPortOnlyKbpsMode is configured, the limit
|
|
will be an absolute value in kilobits-per-second. The kbps rate
|
|
is specified in hpUnknownUnicastLimitPortSingleControlKbps. If
|
|
disabled is configured, any unknown-unicast rate limit will be
|
|
removed."
|
|
DEFVAL { disabled }
|
|
::= { hpUnknownUnicastLimitConfigEntry 2 }
|
|
|
|
hpUnknownUnicastLimitPortSingleControlPrct OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When hpUnknownUnicastLimitPortControlMode is
|
|
unknownUnicastLimitPerPortOnly, this value is the maximum allowed
|
|
ingress rate for unknown-unicast traffic on this port as a
|
|
percentage of the current line rate."
|
|
::= { hpUnknownUnicastLimitConfigEntry 3 }
|
|
|
|
hpUnknownUnicastLimitPortSingleControlKbps OBJECT-TYPE
|
|
SYNTAX Integer32 (0..100000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When hpUnknownUnicastLimitPortControlMode is
|
|
UnknownUnicastLimitPerPortOnlyKbpsMode, this value is the maximum
|
|
allowed ingress rate for unknown-unicast traffic on this port in
|
|
kilobits-per-second."
|
|
::= { hpUnknownUnicastLimitConfigEntry 4 }
|
|
|
|
|
|
--
|
|
-- hpicf vlan rate limit config Table
|
|
--
|
|
hpicfIngressRateLimitVlanObjects OBJECT IDENTIFIER ::= {hpicfRateLimitObjects 9}
|
|
|
|
hpicfIngressRateLimitVlanConfigTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF HpicfIngressRateLimitVlanConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A table of VLAN rate limits."
|
|
::= { hpicfIngressRateLimitVlanObjects 1 }
|
|
|
|
hpicfIngressRateLimitVlanConfigEntry OBJECT-TYPE
|
|
SYNTAX HpicfIngressRateLimitVlanConfigEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "A set of objects used to configure rate
|
|
limits on a VLANs."
|
|
INDEX {hpicfIngressRateLimitVlanIndex }
|
|
::= { hpicfIngressRateLimitVlanConfigTable 1 }
|
|
|
|
HpicfIngressRateLimitVlanConfigEntry ::= SEQUENCE {
|
|
hpicfIngressRateLimitVlanIndex InterfaceIndex,
|
|
hpicfIngressRateLimitVlanControlMode INTEGER,
|
|
hpicfIngressRateLimitVlanKbps Unsigned32
|
|
}
|
|
|
|
hpicfIngressRateLimitVlanIndex OBJECT-TYPE
|
|
SYNTAX InterfaceIndex
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION "The VLAN ifIndex value that uniquely
|
|
identifies a row in the Interfaces Table
|
|
and corresponds to the VLAN on which the rate
|
|
limit is being set."
|
|
::= { hpicfIngressRateLimitVlanConfigEntry 1 }
|
|
|
|
hpicfIngressRateLimitVlanControlMode OBJECT-TYPE
|
|
SYNTAX INTEGER
|
|
{
|
|
disabled(1),
|
|
ingressVlanKbps(2)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The rate limit mode. A value of 1 indicates that
|
|
there is no rate limit set. A value of 2 indicates
|
|
that the rate limit on the VLAN will be set in
|
|
Kilobits per second."
|
|
DEFVAL { disabled }
|
|
::= { hpicfIngressRateLimitVlanConfigEntry 2 }
|
|
|
|
hpicfIngressRateLimitVlanKbps OBJECT-TYPE
|
|
SYNTAX Unsigned32(0..260000000)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION "The maximum rate of inbound traffic permitted on
|
|
the VLAN in kilobits per second. This limit is the
|
|
total aggregate inbound traffic allowed across all
|
|
ports in the VLAN. The value of this object only
|
|
takes effect when hpicfIngressRateLimitVlanControlMode is
|
|
set to 'ingressVlanKbps. A limit of 0 will drop all
|
|
traffic. The actual traffic limit applied in
|
|
hardware may be rounded down to the nearest multiple
|
|
of the platform-dependent rate limiting
|
|
granularity."
|
|
::= { hpicfIngressRateLimitVlanConfigEntry 3 }
|
|
|
|
-- Conformance Information
|
|
|
|
hpicfRateLimitConformance OBJECT IDENTIFIER ::= { hpicfRateLimitMIB 2 }
|
|
|
|
hpicfRateLimitGroups OBJECT IDENTIFIER ::= { hpicfRateLimitConformance 1 }
|
|
|
|
hpicfRateLimitCompliances OBJECT IDENTIFIER
|
|
::= { hpicfRateLimitConformance 2 }
|
|
|
|
-- units of conformance
|
|
|
|
hpICMPRateLimitPortConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
hpICMPRateLimitPortState,
|
|
hpICMPRateLimitPortPrct,
|
|
hpICMPRateLimitPortAlarmFlag,
|
|
hpICMPRateLimitNotifyPortIndex
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to ICMP rate
|
|
limiting on an interface."
|
|
::= { hpicfRateLimitGroups 1 }
|
|
|
|
hpICMPRateLimitPortNotifyGroup NOTIFICATION-GROUP
|
|
NOTIFICATIONS { hpICMPRateLimitPortNotification }
|
|
STATUS current
|
|
DESCRIPTION "A collection of notifications used to indicate
|
|
ICMP rate limiting on an interface events."
|
|
::= { hpicfRateLimitGroups 2 }
|
|
|
|
hpBWMinIngressPortConfigGroup OBJECT-GROUP
|
|
OBJECTS { hpBWMinIngressPortNumQueues,
|
|
hpBWMinIngressPortPrct }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to Guaranteed
|
|
Minimum ingress bandwidth on an interface."
|
|
::= { hpicfRateLimitGroups 3 }
|
|
|
|
hpBWMinEgressPortConfigGroup OBJECT-GROUP
|
|
OBJECTS { hpBWMinEgressPortNumQueues,
|
|
hpBWMinEgressPortPrct }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to Guaranteed
|
|
Minimum egress bandwidth on an interface."
|
|
::= { hpicfRateLimitGroups 4 }
|
|
|
|
hpEgressRateLimitPortConfigGroup OBJECT-GROUP
|
|
OBJECTS { hpEgressRateLimitPortNumQueues,
|
|
hpEgressRateLimitPortControlMode,
|
|
hpEgressRateLimitPortSingleControlPrct,
|
|
hpEgressRateLimitPortSingleControlBps,
|
|
hpEgressRateLimitPortPrct,
|
|
hpEgressRateLimitPortBps,
|
|
hpEgressRateLimitPortSingleControlKbps
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to Egress
|
|
Rate-Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 5 }
|
|
|
|
hpIngressRateLimitPortConfigGroup OBJECT-GROUP
|
|
OBJECTS { hpIngressRateLimitPortNumQueues,
|
|
hpIngressRateLimitPortControlMode,
|
|
hpIngressRateLimitPortSingleControlPrct,
|
|
hpIngressRateLimitPortSingleControlBps,
|
|
hpIngressRateLimitPortPrct,
|
|
hpIngressRateLimitPortBps,
|
|
hpIngressRateLimitPortSingleControlKbps
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to Ingress
|
|
Rate-Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 6 }
|
|
|
|
hpICMPRateLimitPortConfigGroup2 OBJECT-GROUP
|
|
OBJECTS {
|
|
hpICMPRateLimitPortPrct,
|
|
hpICMPRateLimitPortAlarmFlag,
|
|
hpICMPRateLimitNotifyPortIndex,
|
|
hpICMPRateLimitPortKbps,
|
|
hpICMPRateLimitPortControlMode
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This replaces the deprecated hpICMPRateLimitPortConfigGroup.
|
|
A collection of objects providing configuration to ICMP rate
|
|
limiting on an interface."
|
|
::= { hpicfRateLimitGroups 7 }
|
|
|
|
hpEgressRateLimitPortConfigGroup2 OBJECT-GROUP
|
|
OBJECTS { hpEgressRateLimitPortNumQueues,
|
|
hpEgressRateLimitPortControlMode,
|
|
hpEgressRateLimitPortSingleControlPrct,
|
|
hpEgressRateLimitPortPrct,
|
|
hpEgressRateLimitPortSingleControlKbps
|
|
}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"This replaces the deprecated hpEgressRateLimitPortConfigGroup.
|
|
A collection of objects providing configuration to Egress
|
|
Rate-Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 8 }
|
|
|
|
hpIngressRateLimitPortConfigGroup2 OBJECT-GROUP
|
|
OBJECTS { hpIngressRateLimitPortNumQueues,
|
|
hpIngressRateLimitPortControlMode,
|
|
hpIngressRateLimitPortSingleControlPrct,
|
|
hpIngressRateLimitPortPrct,
|
|
hpIngressRateLimitPortSingleControlKbps
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This replaces the deprecated hpIngressRateLimitPortConfigGroup.
|
|
A collection of objects providing configuration to Ingress
|
|
Rate-Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 9 }
|
|
|
|
hpBcastLimitIngressPortConfigGroup OBJECT-GROUP
|
|
OBJECTS { hpIngressBcastLimitPortControlMode,
|
|
hpIngressBcastLimitPortSingleControlPrct }
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to
|
|
Ingress Broadcast Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 10 }
|
|
|
|
hpMcastLimitIngressPortConfigGroup OBJECT-GROUP
|
|
OBJECTS { hpIngressMcastLimitPortControlMode,
|
|
hpIngressMcastLimitPortSingleControlPrct }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to
|
|
Ingress Multicast Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 11 }
|
|
|
|
hpBcastLimitIngressPortConfigGroup2 OBJECT-GROUP
|
|
OBJECTS { hpIngressBcastLimitPortControlMode,
|
|
hpIngressBcastLimitPortSingleControlPrct,
|
|
hpIngressBcastLimitPortSingleControlKbps }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This replaces the deprecated hpBcastLimitIngressPortConfigGroup.
|
|
A collection of objects providing configuration of
|
|
Ingress Broadcast Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 12 }
|
|
|
|
hpMcastLimitIngressPortConfigGroup2 OBJECT-GROUP
|
|
OBJECTS { hpIngressMcastLimitPortControlMode,
|
|
hpIngressMcastLimitPortSingleControlPrct,
|
|
hpIngressMcastLimitPortSingleControlKbps }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This replaces the deprecated hpMcastLimitIngressPortConfigGroup
|
|
A collection of objects providing configuration of
|
|
Ingress Multicast Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 13 }
|
|
|
|
hpICMPRateLimitPortConfigGroup3 OBJECT-GROUP
|
|
OBJECTS {
|
|
hpICMPRateLimitPortPrct,
|
|
hpICMPRateLimitPortAlarmFlag,
|
|
hpICMPRateLimitNotifyPortIndex,
|
|
hpICMPRateLimitPortKbps,
|
|
hpICMPRateLimitPortControlMode,
|
|
hpICMPRateLimitPortIpPacketType
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This replaces the deprecated hpICMPRateLimitPortConfigGroup2.
|
|
A collection of objects providing configuration for ICMP rate
|
|
limiting on an interface."
|
|
::= { hpicfRateLimitGroups 14 }
|
|
|
|
hpUnknownUcastLimitIngressPortConfigGroup OBJECT-GROUP
|
|
OBJECTS { hpUnknownUnicastLimitPortControlMode,
|
|
hpUnknownUnicastLimitPortSingleControlPrct}
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to
|
|
Ingress Unknown Unicast traffic Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 15 }
|
|
|
|
hpicfIngressRateLimitVlanGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
hpicfIngressRateLimitVlanControlMode,
|
|
hpicfIngressRateLimitVlanKbps }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of HP proprietary objects to support
|
|
configuration of VLAN-based rate limits on HP Networking
|
|
devices."
|
|
::= { hpicfRateLimitGroups 16 }
|
|
|
|
hpUnknownUcastLimitIngressPortConfigGroup2 OBJECT-GROUP
|
|
OBJECTS { hpUnknownUnicastLimitPortControlMode,
|
|
hpUnknownUnicastLimitPortSingleControlPrct,
|
|
hpUnknownUnicastLimitPortSingleControlKbps }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to
|
|
Ingress Unknown Unicast traffic Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 17 }
|
|
|
|
hpEgressRateLimitPortConfigGroup3 OBJECT-GROUP
|
|
OBJECTS { hpEgressRateLimitPortNumQueues,
|
|
hpEgressRateLimitPortControlMode,
|
|
hpEgressRateLimitPortSingleControlPrct,
|
|
hpEgressRateLimitPortPrct,
|
|
hpEgressRateLimitPortSingleControlKbps,
|
|
hpEgressRateLimitPortQueueControlMode
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This replaces the deprecated hpEgressRateLimitPortConfigGroup2.
|
|
A collection of objects providing configuration to Egress
|
|
Rate-Limiting on an interface."
|
|
::= { hpicfRateLimitGroups 18 }
|
|
|
|
hpEgressRateLimitPortQueueConfigEntryGroup OBJECT-GROUP
|
|
OBJECTS { hpEgressRateLimitPortQueueMax }
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of objects providing configuration to egress
|
|
rate-limit on an interface queues."
|
|
::= { hpicfRateLimitGroups 19 }
|
|
|
|
-- compliance statements
|
|
|
|
|
|
hpicfRateLimitCompliance MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for device support of
|
|
HP-ICF-RATE-LIMIT MIB."
|
|
MODULE -- This Module
|
|
|
|
MANDATORY-GROUPS { hpICMPRateLimitPortConfigGroup,
|
|
hpICMPRateLimitPortNotifyGroup
|
|
}
|
|
::= { hpicfRateLimitCompliances 1 }
|
|
|
|
hpicfRateLimitCompliance1 MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for device support of
|
|
HP-ICF-RATE-LIMIT MIB."
|
|
MODULE -- This Module
|
|
|
|
MANDATORY-GROUPS { hpICMPRateLimitPortConfigGroup2,
|
|
hpICMPRateLimitPortNotifyGroup,
|
|
hpBWMinIngressPortConfigGroup,
|
|
hpBWMinEgressPortConfigGroup,
|
|
hpEgressRateLimitPortConfigGroup2,
|
|
hpIngressRateLimitPortConfigGroup2,
|
|
hpBcastLimitIngressPortConfigGroup,
|
|
hpMcastLimitIngressPortConfigGroup,
|
|
hpUnknownUcastLimitIngressPortConfigGroup
|
|
}
|
|
::= { hpicfRateLimitCompliances 2 }
|
|
|
|
hpicfRateLimitCompliance2 MODULE-COMPLIANCE
|
|
STATUS deprecated
|
|
DESCRIPTION
|
|
"The compliance statement for device support of
|
|
HP-ICF-RATE-LIMIT MIB."
|
|
MODULE -- This Module
|
|
|
|
MANDATORY-GROUPS { hpICMPRateLimitPortConfigGroup3,
|
|
hpICMPRateLimitPortNotifyGroup,
|
|
hpBWMinEgressPortConfigGroup,
|
|
hpBWMinIngressPortConfigGroup,
|
|
hpEgressRateLimitPortConfigGroup,
|
|
hpEgressRateLimitPortConfigGroup2,
|
|
hpIngressRateLimitPortConfigGroup,
|
|
hpIngressRateLimitPortConfigGroup2,
|
|
hpBcastLimitIngressPortConfigGroup2,
|
|
hpMcastLimitIngressPortConfigGroup2,
|
|
hpUnknownUcastLimitIngressPortConfigGroup
|
|
}
|
|
OBJECT hpICMPRateLimitPortIpPacketType
|
|
MIN-ACCESS not-accessible
|
|
DESCRIPTION "Read and write access not required"
|
|
::= { hpicfRateLimitCompliances 3 }
|
|
|
|
hpicfRateLimitCompliance3 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION "The compliance statement for HP switches
|
|
running IngressRateLimitVlan feature."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS { hpicfIngressRateLimitVlanGroup }
|
|
|
|
::= { hpicfRateLimitCompliances 4 }
|
|
|
|
hpicfRateLimitCompliance4 MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for device support of
|
|
HP-ICF-RATE-LIMIT MIB."
|
|
MODULE -- This Module
|
|
|
|
MANDATORY-GROUPS { hpICMPRateLimitPortConfigGroup3,
|
|
hpICMPRateLimitPortNotifyGroup,
|
|
hpBWMinEgressPortConfigGroup,
|
|
hpBWMinIngressPortConfigGroup,
|
|
hpEgressRateLimitPortConfigGroup3,
|
|
hpEgressRateLimitPortQueueConfigEntryGroup,
|
|
hpIngressRateLimitPortConfigGroup2,
|
|
hpBcastLimitIngressPortConfigGroup2,
|
|
hpMcastLimitIngressPortConfigGroup2,
|
|
hpUnknownUcastLimitIngressPortConfigGroup2
|
|
}
|
|
OBJECT hpICMPRateLimitPortIpPacketType
|
|
MIN-ACCESS not-accessible
|
|
DESCRIPTION "Read and write access not required"
|
|
::= { hpicfRateLimitCompliances 5 }
|
|
|
|
|
|
END
|