WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/d-link/DES7200-OSPF-MIB

2951 lines
97 KiB
Plaintext
Raw Permalink Blame History

-- *****************************************************************
-- MY-OSPF-MIB.mib: My Ospf MIB file
--
-- $Copyright$
--
-- *****************************************************************
--
DES7200-OSPF-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Integer32,
Counter32
FROM SNMPv2-SMI
TruthValue,
DisplayString,
RowStatus,
MacAddress
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF
ConfigStatus,
IfIndex
FROM DES7200-TC
EnabledStatus
FROM P-BRIDGE-MIB
AreaID,UpToMaxAge,Status,PositiveInteger,
DesignatedRouterPriority,RouterID,HelloRange
FROM OSPF-MIB
myMgmt
FROM DES7200-SMI;
myOspfMIB MODULE-IDENTITY
LAST-UPDATED "200211200000Z"
ORGANIZATION "$Company$"
CONTACT-INFO
"
Tel: $Telephone$
E-mail: $E-mail$"
DESCRIPTION
"This module defines my Ospf mibs."
REVISION "200211200000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { myMgmt 30}
myOspfMIBObjects OBJECT IDENTIFIER ::= { myOspfMIB 1 }
-- general mib
myOspfGeneralMibsGroup OBJECT IDENTIFIER ::= { myOspfMIBObjects 1 }
--Minimum LSA interval
myOspfMiniLsaInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum LSA interval that the two LSA generate."
::={ myOspfGeneralMibsGroup 1 }
--Minimum LSA arrival
myOspfMiniLsaArrival OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Minimum LSA Interval of the two LSA arrival."
::={ myOspfGeneralMibsGroup 2 }
--Number of areas in this router
myOspfAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of areas in this router"
::={ myOspfGeneralMibsGroup 3 }
myOspfNormalAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of normal areas in this router"
::={ myOspfGeneralMibsGroup 4}
myOspfStubAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of stub areas in this router"
::={ myOspfGeneralMibsGroup 5 }
myOspfNssaAreasNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of nssa areas in this router"
::={ myOspfGeneralMibsGroup 6 }
myOspfSpfDelay OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Ospf Spf shedule time, an integer from 0 to 65535. The default is 5
seconds,0 means no delay."
DEFVAL {5}
::={ myOspfGeneralMibsGroup 7 }
myOspfSpfHoldTime OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"hold time between two Spfs.an integer from 0 to 65535. The default is
10 seconds; 0 means no delay."
DEFVAL {10}
::={ myOspfGeneralMibsGroup 8 }
myOspfAutoCostRefBandWidthRef OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set AutoCost bandwidth referenc value in unit of Mbits.
Setting this value to 0 indicate that disable the feature of
autocost bandwidth referenc."
DEFVAL {100}
::={ myOspfGeneralMibsGroup 9 }
myOspfLsaGroupPacing OBJECT-TYPE
SYNTAX Unsigned32(10..1800)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"set the group pacing of LSAs."
DEFVAL {240}
::={ myOspfGeneralMibsGroup 10}
myOspfInterDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set inter-area distance."
DEFVAL {110}
::= { myOspfGeneralMibsGroup 11 }
myOspfIntraDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set intra-area distance."
DEFVAL {110}
::= { myOspfGeneralMibsGroup 12 }
myOspfExternDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set extern distance."
DEFVAL {110}
::= { myOspfGeneralMibsGroup 13 }
--LogAdjChangeNotify
myOspfLogAdjChangeNotify OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"if enabled status is setted,
Send syslog message when a neighbor state changes."
DEFVAL {enabled}
::= { myOspfGeneralMibsGroup 14 }
myOspfPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The myOspfIfPassiveStatus of a interface equal to this object value
when this interface is created. If you change this object value to 'enabled'
or 'disabled'all interfaces which have exist will also change their
myOspfIfPassiveStatus to 'enabled' or 'disabled'."
DEFVAL { disabled }
::={ myOspfGeneralMibsGroup 15 }
myOspfRFC1583Compatibility OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the preference rules used in calculating AS external routes
(RFC2328 Section 16.4) when choosing among multiple AS-external-LSAs
advertising the same destination. When set to 'enabled', the preference
rules remain those specified by RFC 1583 ([Ref9]). When set
to 'disabled', the preference rules are those stated in
'RFC2328 Section 16.4.1' which prevent routing loops when AS-
external-LSAs for the same destination have been originated
from different areas. Set to 'enabled' by default."
REFERENCE
"OSPF Version 2(RFC2328), C.1 Global parameters"
DEFVAL { enabled }
::={ myOspfGeneralMibsGroup 16 }
myOspfRouteRedisDefMetricVal OBJECT-TYPE
SYNTAX Unsigned32(1..16777214)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this value is setted,Cause the current routing protocol(ospf)
to use the same metricvalue for all redistributed routes (BGP, RIP, and OSPF)."
DEFVAL {20}
::= { myOspfGeneralMibsGroup 17}
myOspfAdminiDistance OBJECT-TYPE
SYNTAX Unsigned32(1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"ospf Administrative distance."
DEFVAL {110}
::= { myOspfGeneralMibsGroup 18}
--table mib
--myOspfAreaTable
myOspfAreaTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfAreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the configured parame-
ters and cumulative statistics of the router's
attached areas.This table is superset of ospfAreaTable"
::= { myOspfMIBObjects 2}
myOspfAreaEntry OBJECT-TYPE
SYNTAX MyOspfAreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The entry of myOspfAreaTable."
INDEX { myOspfAreaId}
::= { myOspfAreaTable 1 }
MyOspfAreaEntry ::=
SEQUENCE {
myOspfAreaId
AreaID,
myOspfAuthType
INTEGER,
myOspfImportAsExtern
INTEGER,
myOspfSpfRuns
Counter32,
myOspfAreaBdrRtrCount
Gauge32,
myOspfAsBdrRtrCount
Gauge32,
myOspfAreaLsaCount
Gauge32,
myOspfAreaLsaCksumSum
Unsigned32,
myOspfAreaSummary
INTEGER,
myOspfAreaStatus
RowStatus,
-- extend parts
myOspfAreaInterfaceNum
Unsigned32,
myOspfAreaNssaIsRedistribution
TruthValue,
myOspfAreaNssaIsDefInfoOriginate
TruthValue
}
myOspfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying an area.
Area ID 0.0.0.0 is used for the OSPF backbone."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { myOspfAreaEntry 1 }
myOspfAuthType OBJECT-TYPE
SYNTAX INTEGER{
none(0),
simplePassword(1),
md5 (2)
-- reserved for specification by IANA (> 2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication type specified for an area.
Additional authentication types may be assigned
locally on a per Area basis."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { myOspfAreaEntry 2 }
myOspfImportAsExtern OBJECT-TYPE
SYNTAX INTEGER {
importExternal (1), --normal area
importNoExternal (2), -- stub area
importNssa (3) -- NSSA area
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The area's support for importing AS external
link- state advertisements."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
DEFVAL { importExternal }
::= { myOspfAreaEntry 3 }
myOspfSpfRuns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that the intra-area route
table has been calculated using this area's
link-state database. This is typically done
using Dijkstra's algorithm."
::= { myOspfAreaEntry 4 }
myOspfAreaBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of area border routers reach-
able within this area. This is initially zero,
and is calculated in each SPF Pass."
::= { myOspfAreaEntry 5 }
myOspfAsBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Autonomous System border
routers reachable within this area. This is
initially zero, and is calculated in each SPF
Pass."
::= { myOspfAreaEntry 6 }
myOspfAreaLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of link-state advertisements
in this area's link-state database, excluding
AS External LSA's."
::= { myOspfAreaEntry 7 }
myOspfAreaLsaCksumSum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32-bit unsigned sum of the link-state ad-
vertisements' LS checksums contained in this
area's link-state database. This sum excludes
external (LS type 5) link-state advertisements.
The sum can be used to determine if there has
been a change in a router's link state data-
base, and to compare the link-state database of
two routers."
DEFVAL { 0 }
::= { myOspfAreaEntry 8 }
myOspfAreaSummary OBJECT-TYPE
SYNTAX INTEGER {
noAreaSummary (1),
sendAreaSummary (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable ospfAreaSummary controls the im-
port of summary LSAs into stub areas. It has
no effect on other areas.
If it is noAreaSummary, the router will neither
originate nor propagate summary LSAs into the
stub area. It will rely entirely on its de-
fault route.
If it is sendAreaSummary, the router will both
summarize and propagate summary LSAs."
DEFVAL { sendAreaSummary }
::= { myOspfAreaEntry 9 }
myOspfAreaStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { myOspfAreaEntry 10 }
myOspfAreaInterfaceNum OBJECT-TYPE --for command "show
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the interface number of this area"
::= { myOspfAreaEntry 11 }
myOspfAreaNssaIsRedistribution OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" if it's disabled , when the router is an NSSA ABR and
you want the redistribute command to import routes into normal
areas, but not into the NSSA,
this field is vaild for nssa area"
DEFVAL {true}
::= { myOspfAreaEntry 12}
myOspfAreaNssaIsDefInfoOriginate OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"if it's enabled it meaning that on an ABR to allow
importing type 7 LSAs into the NSSA,
this field is valid for nssa area"
DEFVAL {false}
::= { myOspfAreaEntry 13}
--network address scope table
myOspfAddressScopeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfAddressScopeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Define an interface on which OSPF runs and the area ID for that
interface. You can use the wildcard-mask to use a single
command to define one or more multiple interfaces to be
associated with a specific OSPF area. "
::= { myOspfMIBObjects 3 }
myOspfAddressScopeEntry OBJECT-TYPE
SYNTAX MyOspfAddressScopeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry define an scope of address for ospf routing."
INDEX { myOspfNetWorkAreaID,myOspfNetWorkAddress, myOspfNetWorkMask}
::= { myOspfAddressScopeTable 1 }
MyOspfAddressScopeEntry ::=
SEQUENCE {
myOspfNetWorkAreaID
IpAddress,
myOspfNetWorkAddress
IpAddress,
myOspfNetWorkMask
IpAddress,
myOspfNetWorkStatus
RowStatus
}
myOspfNetWorkAreaID OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"area ID"
::= { myOspfAddressScopeEntry 1 }
myOspfNetWorkAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Routing for Networks Ipaddress"
::= { myOspfAddressScopeEntry 2 }
myOspfNetWorkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Routing for Networks mask"
::= { myOspfAddressScopeEntry 3 }
myOspfNetWorkStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" when this value is destroy,the
entry will be deleted"
::= { myOspfAddressScopeEntry 4 }
-- The Ospf Interface Configuration Table
myOspfIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Interface Table describes the interfaces
from the viewpoint of OSPF."
REFERENCE
"ospfIfTable in rfc1850"
::= { myOspfMIBObjects 4 }
myOspfIfEntry OBJECT-TYPE
SYNTAX MyOspfIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Interface Entry describes one inter-
face configuration of OSPF."
INDEX { myOspfIfIpAddress, myOspfAddressLessIf }
::= { myOspfIfTable 1 }
MyOspfIfEntry ::=
SEQUENCE {
myOspfIfIpAddress
IpAddress,
myOspfAddressLessIf
Unsigned32,
myOspfIfAreaId
AreaID,
myOspfIfType
INTEGER,
myOspfIfAdminStat
Status,
myOspfIfRtrPriority
DesignatedRouterPriority,
myOspfIfTransitDelay
Unsigned32,
myOspfIfRetransInterval
Unsigned32,
myOspfIfHelloInterval
HelloRange,
myOspfIfRtrDeadInterval
PositiveInteger,
myOspfIfPollInterval
PositiveInteger,
myOspfIfState
INTEGER,
myOspfIfDesignatedRouter
IpAddress,
myOspfIfBackupDesignatedRouter
IpAddress,
myOspfIfEvents
Counter32,
myOspfIfAuthType
INTEGER,
myOspfIfAuthKey
OCTET STRING,
myOspfIfStatus
RowStatus,
myOspfIfMulticastForwarding
INTEGER,
myOspfIfDemand
TruthValue,
myOspfIfDatabaseFilterAllOut
EnabledStatus,
myOspfIfDesignateRouterId
IpAddress,
myOspfIfBackupDesignateRouterId
IpAddress,
myOspfIfWaitInternal
Unsigned32,
myOspfIfPassiveStatus
EnabledStatus,
myOspfIfCurrentUsedMd5AuthKeyId
Unsigned32
}
myOspfIfIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of this OSPF interface."
::= { myOspfIfEntry 1 }
myOspfAddressLessIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP Addresses, and the corresponding value of
ifIndex for interfaces having no IP Address."
::= { myOspfIfEntry 2 }
myOspfIfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0.0.0.0 is used for the OSPF backbone."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { myOspfIfEntry 3 }
myOspfIfType OBJECT-TYPE
SYNTAX INTEGER {
broadcast (1),
nbma (2),
pointToPoint (3),
pointToMultipoint (5),
loopback(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The OSPF interface type.
By way of a default, this field may be intuited
from the corresponding value of ifType. Broad-
cast LANs, such as Ethernet and IEEE 802.5,
take the value 'broadcast', X.25 and similar
technologies take the value 'nbma', and links
that are definitively point to point take the
value 'pointToPoint'."
::= { myOspfIfEntry 4 }
myOspfIfAdminStat OBJECT-TYPE
SYNTAX Status
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The OSPF interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to OSPF."
::= { myOspfIfEntry 5 }
myOspfIfRtrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not eligi-
ble to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker."
DEFVAL { 1 }
::= { myOspfIfEntry 6 }
myOspfIfTransitDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link state update packet over this
interface."
DEFVAL { 1 }
::= { myOspfIfEntry 7 }
myOspfIfRetransInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets."
DEFVAL { 5 }
::= { myOspfIfEntry 8 }
myOspfIfHelloInterval OBJECT-TYPE
SYNTAX HelloRange
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for all
routers attached to a common network."
DEFVAL { 10 }
::= { myOspfIfEntry 9 }
myOspfIfRtrDeadInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for all routers attached
to a common network."
DEFVAL { 40 }
::= { myOspfIfEntry 10 }
myOspfIfPollInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The larger time interval, in seconds, between
the Hello packets sent to an inactive non-
broadcast multi- access neighbor."
::= { myOspfIfEntry 11 }
myOspfIfState OBJECT-TYPE
SYNTAX INTEGER {
down (1),
loopback (2),
waiting (3),
pointToPoint (4),
designatedRouter (5),
backupDesignatedRouter (6),
otherDesignatedRouter (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The OSPF Interface State."
DEFVAL { down }
::= { myOspfIfEntry 12 }
myOspfIfDesignatedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP Address of the interface which connected the local router in
the Designated Router."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { myOspfIfEntry 13 }
myOspfIfBackupDesignatedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP Address of the interface which connected the local router in
the Backup Designated Router."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { myOspfIfEntry 14 }
myOspfIfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this OSPF interface has
changed its state, or an error has occurred."
::= { myOspfIfEntry 15 }
myOspfIfAuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Authentication Key. If the Area's Author-
ization Type is simplePassword, and the key
length is shorter than 8 octets, the agent will
left adjust and zero fill to 8 octets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, myOspfIfAuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0
::= { myOspfIfEntry 16 }
myOspfIfStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value will be active(1) always."
::= { myOspfIfEntry 17 }
myOspfIfMulticastForwarding OBJECT-TYPE
SYNTAX INTEGER {
blocked (1), -- no multicast forwarding
multicast (2), -- using multicast address
unicast (3) -- to each OSPF neighbor
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link uni-
casts. Data link multicasting is not meaning-
ful on point to point and NBMA interfaces, and
setting ospfMulticastForwarding to 0 effective-
ly disables all multicast forwarding."
DEFVAL { blocked }
::= { myOspfIfEntry 18 }
myOspfIfDemand OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Demand OSPF procedures (hel-
lo supression to FULL neighbors and setting the
DoNotAge flag on proogated LSAs) should be per-
formed on this interface."
DEFVAL { false }
::= { myOspfIfEntry 19 }
myOspfIfAuthType OBJECT-TYPE
SYNTAX INTEGER (0..255)
-- none (0),
-- simplePassword (1)
-- md5 (2)
-- default (3)
-- reserved for specification by IANA (> 2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The authentication type specified for an interface. Setting this value to
'default' means using default authentication type referenced to Area Authentication,
this value only for set,not be read. Additional authentication types may
be assigned locally."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { myOspfIfEntry 20 }
myOspfIfDatabaseFilterAllOut OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Block flooding of OSPF LSA packets to the interface. By
default, OSPF floods new LSAs over all interfaces in the same area,
except the interface on which the LSA arrives."
DEFVAL {disabled}
::= { myOspfIfEntry 21 }
myOspfIfDesignateRouterId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"DR RouterID of this interface,
when DR does not selected,DR Id is 0.0.0.0"
DEFVAL {'00000000'H}
::= { myOspfIfEntry 22 }
myOspfIfBackupDesignateRouterId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Backup DR RouterId of this interface ,
when Backup DR does not selected,BDR Id is 0.0.0.0"
DEFVAL {'00000000'H}
::= { myOspfIfEntry 23 }
myOspfIfWaitInternal OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The wait time of hello generate"
::= { myOspfIfEntry 24 }
myOspfIfPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object value to 'enabled' ,the interface will
become a passive interface."
DEFVAL { disabled }
::= { myOspfIfEntry 25 }
myOspfIfCurrentUsedMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"key-id which current used for md5 authentication,this value is
valid from 1 to 255, the value 0 is default value.."
DEFVAL {0}
::= { myOspfIfEntry 26 }
-- The Ospf Interface MD5 authentication key configuration table
myOspfIfMd5AuthKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration table of the key-id for md5 authentication for OSPF protocol."
::= { myOspfMIBObjects 5 }
myOspfIfMd5AuthKeyEntry OBJECT-TYPE
SYNTAX MyOspfIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration entry of the key-id for md5 authentication for OSPF protocol"
INDEX {myOspfIfMd5AuthKeyIf, myOspfIfMd5AuthKeyId }
::= { myOspfIfMd5AuthKeyTable 1 }
MyOspfIfMd5AuthKeyEntry ::=
SEQUENCE {
myOspfIfMd5AuthKeyIf
Unsigned32,
myOspfIfMd5AuthKeyId
Unsigned32,
myOspfIfMd5AuthKey
OCTET STRING,
myOspfIfMd5AuthKeySt
ConfigStatus
}
myOspfIfMd5AuthKeyIf OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Corresponding value of ifIndex for interfaces."
::= { myOspfIfMd5AuthKeyEntry 1 }
myOspfIfMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the key-id for md5 authentication."
::= { myOspfIfMd5AuthKeyEntry 2 }
myOspfIfMd5AuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Authentication Key for MD5.
When read, myOspfIfMd5AuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
::= { myOspfIfMd5AuthKeyEntry 3 }
myOspfIfMd5AuthKeySt OBJECT-TYPE
SYNTAX ConfigStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this value to 'invalid' will delete this entry.
Setting this value to 'valid' will have no effect."
::= { myOspfIfMd5AuthKeyEntry 4 }
-- The My Ospf Virtual Link Table
myOspfVirtTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfVirtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about this router's virtual inter-
faces.Include ospfVirtIfTable in rfc1850"
REFERENCE
"ospfVirtIfTable in rfc1850"
::= { myOspfMIBObjects 6 }
myOspfVirtEntry OBJECT-TYPE
SYNTAX MyOspfVirtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Virtual Interface"
INDEX {myOspfVirtIfAreaId, myOspfVirtIfNeighbor}
::= { myOspfVirtTable 1 }
MyOspfVirtEntry ::=
SEQUENCE {
myOspfVirtIfAreaId
AreaID,
myOspfVirtIfNeighbor
RouterID,
myOspfVirtIfTransitDelay
Unsigned32,
myOspfVirtIfRetransInterval
Unsigned32,
myOspfVirtIfHelloInterval
HelloRange,
myOspfVirtIfRtrDeadInterval
PositiveInteger,
myOspfVirtIfState
INTEGER,
myOspfVirtIfEvents
Counter32,
myOspfVirtIfAuthType
INTEGER,
myOspfVirtIfAuthKey
OCTET STRING,
myOspfVirtIfStatus
RowStatus,
myOspfVirtCost
Unsigned32,
myOspfVirtNativeIfIndex
INTEGER,
myOspfVirtLinkState
INTEGER,
myOspfVirtHelloDueIn
TimeTicks,
myOspfVirtCurrentUsedMd5AuthKeyId
Unsigned32
}
myOspfVirtIfAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0"
::= { myOspfVirtEntry 1 }
myOspfVirtIfNeighbor OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Virtual Neighbor."
::= { myOspfVirtEntry 2 }
myOspfVirtIfTransitDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link- state update packet over this
interface."
DEFVAL { 1 }
::= { myOspfVirtEntry 3 }
myOspfVirtIfRetransInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets. This
value should be well over the expected round-
trip time."
DEFVAL { 5 }
::= { myOspfVirtEntry 4 }
myOspfVirtIfHelloInterval OBJECT-TYPE
SYNTAX HelloRange
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for the
virtual neighbor."
DEFVAL { 10 }
::= { myOspfVirtEntry 5 }
myOspfVirtIfRtrDeadInterval OBJECT-TYPE
SYNTAX PositiveInteger
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for the virtual neigh-
bor."
DEFVAL { 40 }
::= { myOspfVirtEntry 6 }
myOspfVirtIfState OBJECT-TYPE
SYNTAX INTEGER {
down (1), -- these use the same encoding
pointToPoint (4) -- as the ospfIfTable
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"OSPF virtual interface states."
DEFVAL { down }
::= { myOspfVirtEntry 7 }
myOspfVirtIfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of state changes or error events on
this Virtual Link"
::= { myOspfVirtEntry 8 }
myOspfVirtIfAuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If Authentication Type is simplePassword, the
device will left adjust and zero fill to 8 oc-
tets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, ospfVifAuthKey always returns a
string of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0
::= { myOspfVirtEntry 9 }
myOspfVirtIfStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { myOspfVirtEntry 10 }
myOspfVirtIfAuthType OBJECT-TYPE
SYNTAX INTEGER (0..255)
-- none (0),
-- simplePassword (1),
-- md5 (2),
-- default (3)
-- reserved for specification by IANA (> 2)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The authentication type specified for a virtual interface. Setting this value
'default' means using default authentication type referenced to Area Authentication,
this value only for set,not be read. Additional authentication types
may be assigned locally."
REFERENCE
"OSPF Version 2, Appendix E Authentication"
DEFVAL { 0 } -- no authentication, by default
::= { myOspfVirtEntry 11 }
myOspfVirtCost OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Explicitly specify the cost of sending a packet on the
interface."
::= { myOspfVirtEntry 12 }
myOspfVirtNativeIfIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the Interface's Index that The Virtual Link
via this interface."
::= { myOspfVirtEntry 13 }
myOspfVirtLinkState OBJECT-TYPE
SYNTAX INTEGER{
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Virtual Link State is up or down."
::= { myOspfVirtEntry 14 }
myOspfVirtHelloDueIn OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the time when hello due in."
::= { myOspfVirtEntry 15 }
myOspfVirtCurrentUsedMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"the key-id which current used for md5 authentication,this value is
valid from 1 to 255, the value 0 is default value."
DEFVAL {0}
::= { myOspfVirtEntry 16 }
-- The Ospf Virtual Interface MD5 authentication key configuration table
myOspfVirtIfMd5AuthKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfVirtIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration table of the key-id for md5 authentication in VirtIf
for OSPF protocol."
::= { myOspfMIBObjects 7 }
myOspfVirtIfMd5AuthKeyEntry OBJECT-TYPE
SYNTAX MyOspfVirtIfMd5AuthKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Configuration entry of the key-id for md5 authentication in VirtIf
for OSPF protocol"
INDEX {myOspfVirtIfMd5AuthKeyAreaId, myOspfVirtIfMd5AuthKeyNeighbor,
myOspfVirtIfMd5AuthKeyId }
::= { myOspfVirtIfMd5AuthKeyTable 1 }
MyOspfVirtIfMd5AuthKeyEntry ::=
SEQUENCE {
myOspfVirtIfMd5AuthKeyAreaId
AreaID,
myOspfVirtIfMd5AuthKeyNeighbor
RouterID,
myOspfVirtIfMd5AuthKeyId
Unsigned32,
myOspfVirtIfMd5AuthKey
OCTET STRING,
myOspfVirtIfMd5AuthKeySt
ConfigStatus
}
myOspfVirtIfMd5AuthKeyAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0"
::= { myOspfVirtIfMd5AuthKeyEntry 1 }
myOspfVirtIfMd5AuthKeyNeighbor OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Virtual Neighbor."
::= { myOspfVirtIfMd5AuthKeyEntry 2 }
myOspfVirtIfMd5AuthKeyId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the key-id for md5 authentication."
::= { myOspfVirtIfMd5AuthKeyEntry 3 }
myOspfVirtIfMd5AuthKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Authentication Key for MD5.
When read, myOspfVirtIfMd5AuthKey always returns an Oc-
tet String of length zero."
REFERENCE
"OSPF Version 2, Section 9 The Interface Data
Structure"
::= { myOspfVirtIfMd5AuthKeyEntry 4 }
myOspfVirtIfMd5AuthKeySt OBJECT-TYPE
SYNTAX ConfigStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this value to 'invalid' will delete this entry.
Setting this value to 'valid' will have no effect."
::= { myOspfVirtIfMd5AuthKeyEntry 5 }
myOspfLsaDetailInfoMibsGroup OBJECT IDENTIFIER ::= { myOspfMIBObjects 8 }
-- OSPF Link State Database
-- The Link State Database contains the Link State
-- Advertisements from throughout the areas that the
-- device is attached to.
myOspfLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Process's Link State Database."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { myOspfLsaDetailInfoMibsGroup 1 }
myOspfLsdbEntry OBJECT-TYPE
SYNTAX MyOspfLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Link State Advertisement."
INDEX { myOspfLsdbAreaId, myOspfLsdbType,
myOspfLsdbLsid, myOspfLsdbRouterId }
::= { myOspfLsdbTable 1 }
MyOspfLsdbEntry ::=
SEQUENCE {
myOspfLsdbAreaId
AreaID,
myOspfLsdbType
INTEGER,
myOspfLsdbLsid
IpAddress,
myOspfLsdbRouterId
RouterID,
myOspfLsdbSequence
Unsigned32,
myOspfLsdbAge
Unsigned32,
myOspfLsdbChecksum
Unsigned32,
myOspfLsdbAdvertisement
OCTET STRING,
myOspfLsdbLinkNum --equal LinkCount
Unsigned32,
myOspfLsdbPacketLength
INTEGER,
myOspfSummaryLsaNetworkMask
IpAddress,
myOspfSummaryLsaTos0Metric
Unsigned32,
myOspfNssaLsaDetailMetricType
INTEGER,
myOspfNssaLsaDetailForwardAddr
IpAddress,
myOspfNssaLsaDetailRouteTag
Unsigned32,
myOspfLsdbOption
Unsigned32
}
myOspfLsdbAreaId OBJECT-TYPE
SYNTAX AreaID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit identifier of the Area from which
the LSA was received."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { myOspfLsdbEntry 1 }
-- External Link State Advertisements are permitted
-- for backward compatibility, but should be displayed in
-- the ospfExtLsdbTable rather than here.
myOspfLsdbType OBJECT-TYPE
SYNTAX INTEGER {
routerLink (1),
networkLink (2),
summaryLink (3),
asSummaryLink (4),
asExternalLink (5), -- but see myOspfExtLsdbTable
multicastLink (6),
nssaExternalLink (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate advertise-
ment format."
REFERENCE
"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"
::= { myOspfLsdbEntry 2 }
myOspfLsdbLsid OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.4 Link State ID"
::= { myOspfLsdbEntry 3 }
myOspfLsdbRouterId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { myOspfLsdbEntry 4 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It mys with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
myOspfLsdbSequence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { myOspfLsdbEntry 5 }
myOspfLsdbAge OBJECT-TYPE
SYNTAX Unsigned32 -- Should be 0..MaxAge
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state adver-
tisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { myOspfLsdbEntry 6 }
myOspfLsdbChecksum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { myOspfLsdbEntry 7 }
myOspfLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { myOspfLsdbEntry 8 }
myOspfLsdbLinkNum OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" the link count of this Router Link Lsa ,
this field is only valid for Router Link Lsa<73><61>type 1 LSA)"
::= { myOspfLsdbEntry 9 }
myOspfLsdbPacketLength OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the lsa packet length ."
::= { myOspfLsdbEntry 10 }
myOspfSummaryLsaNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is only useful when ospfLsdbType is type-3 or
type-4 or type-7,it's the Lsa's network mask ."
::= { myOspfLsdbEntry 11 }
myOspfSummaryLsaTos0Metric OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is only useful when ospfLsdbType is type-3 or
type-4 or type-7,it's the Lsa's tos0 metric ."
::= { myOspfLsdbEntry 12 }
myOspfNssaLsaDetailMetricType OBJECT-TYPE
SYNTAX INTEGER
{ type1(1),
type2(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" this field is valid when Lsa is a type-7 LSA.
The type of Nssa ernal metric. If bit E is set, the metric
specified is a Type 2 external metric. This means the metric is
considered larger than any link state path. If bit E is zero,
the specified metric is a Type 1 external metric. This means
that it is expressed in the same units as the link state metric
(i.e., the same units as interface cost). "
::= { myOspfLsdbEntry 13 }
myOspfNssaLsaDetailForwardAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field is valid when Lsa is a type-7 LSA.
Data traffic for the advertised destination will be forwarded to
this address. If the Forwarding address is set to 0.0.0.0, data
traffic will be forwarded instead to the LSA's originator (i.e.,
the responsible AS boundary router) ."
::= { myOspfLsdbEntry 14 }
myOspfNssaLsaDetailRouteTag OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" this field is valid when Lsa is a type-7 LSA.
A 32-bit field attached to each external route. This is not
used by the OSPF protocol itself. It may be used to communicate
information between AS boundary routers; the precise nature of
such information is outside the scope of this specification."
::= { myOspfLsdbEntry 15 }
myOspfLsdbOption OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the option field indicate which optional capabilities
area associated with the LSA. "
REFERENCE
"OSPF Version 2, Appendix A.2, the Options Field"
::= { myOspfLsdbEntry 16 }
-- OSPF Link State Database, External
-- The Link State Database contains the Link State
-- Advertisements from throughout the areas that the
-- device is attached to.
-- This table is identical to the OSPF LSDB Table in
-- format, but contains only External Link State
-- Advertisements. The purpose is to allow external
-- LSAs to be displayed once for the router rather
-- than once in each non-stub area.
myOspfExtLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfExtLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Process's Links State Database."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { myOspfLsaDetailInfoMibsGroup 2 }
myOspfExtLsdbEntry OBJECT-TYPE
SYNTAX MyOspfExtLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Link State Advertisement."
INDEX { myOspfExtLsdbType, myOspfExtLsdbLsid, myOspfExtLsdbRouterId }
::= { myOspfExtLsdbTable 1 }
MyOspfExtLsdbEntry ::=
SEQUENCE{
myOspfExtLsdbType
INTEGER,
myOspfExtLsdbLsid
IpAddress,
myOspfExtLsdbRouterId
RouterID,
myOspfExtLsdbSequence
Unsigned32,
myOspfExtLsdbAge
Unsigned32,
myOspfExtLsdbChecksum
Unsigned32,
myOspfExtLsdbAdvertisement
OCTET STRING,
myOspfExtLsdbNetworkMask
IpAddress,
myOspfExtLsdbMetricType
INTEGER,
myOspfExtLsdbForwardAddr
IpAddress,
myOspfExtLsdbRouteTag
IpAddress,
myOspfExtLsdbMetric
INTEGER,
myOspfExtLsdbOption
Unsigned32,
myOspfExtLsdbPacketLength
Unsigned32
}
myOspfExtLsdbType OBJECT-TYPE
SYNTAX INTEGER {
asExternalLink (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate advertise-
ment format."
REFERENCE
"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"
::= { myOspfExtLsdbEntry 1 }
myOspfExtLsdbLsid OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.4 Link State ID"
::= { myOspfExtLsdbEntry 2 }
myOspfExtLsdbRouterId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { myOspfExtLsdbEntry 3 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It mys with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
myOspfExtLsdbSequence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { myOspfExtLsdbEntry 4 }
myOspfExtLsdbAge OBJECT-TYPE
SYNTAX Unsigned32 -- Should be 0..MaxAge
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state adver-
tisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { myOspfExtLsdbEntry 5 }
myOspfExtLsdbChecksum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { myOspfExtLsdbEntry 6 }
myOspfExtLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(36))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
REFERENCE
"OSPF Version 2, Section 12 Link State Adver-
tisements"
::= { myOspfExtLsdbEntry 7 }
myOspfExtLsdbNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address mask for the advertised destination. For
example, when advertising a class A network the mask 0xff000000
would be used."
::= { myOspfExtLsdbEntry 8 }
myOspfExtLsdbMetric OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The cost of this route. Interpretation depends on the external
type indication. "
::= { myOspfExtLsdbEntry 9 }
myOspfExtLsdbMetricType OBJECT-TYPE
SYNTAX INTEGER
{ type1(1),
type2(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The type of external metric. If bit E is set, the metric
specified is a Type 2 external metric. This means the metric is
considered larger than any link state path. If bit E is zero,
the specified metric is a Type 1 external metric. This means
that it is expressed in the same units as the link state metric
(i.e., the same units as interface cost). "
::= { myOspfExtLsdbEntry 10 }
myOspfExtLsdbForwardAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Data traffic for the advertised destination will be forwarded to
this address. If the Forwarding address is set to 0.0.0.0, data
traffic will be forwarded instead to the LSA's originator (i.e.,
the responsible AS boundary router) ."
::= { myOspfExtLsdbEntry 11 }
myOspfExtLsdbRouteTag OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit field attached to each external route. This is not
used by the OSPF protocol itself. It may be used to communicate
information between AS boundary routers; the precise nature of
such information is outside the scope of this specification."
::= { myOspfExtLsdbEntry 12 }
myOspfExtLsdbOption OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the option field indicate which optional capabilities
area associated with the LSA. "
REFERENCE
"OSPF Version 2, Appendix A.2, the Options Field"
::= { myOspfExtLsdbEntry 13 }
myOspfExtLsdbPacketLength OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the lsa packet length ."
::= { myOspfExtLsdbEntry 14 }
--Router Lsa's detail information table
myOspfRouterLsaDetailTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfRouterLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the router Lsa's detail Infromtion."
::= { myOspfLsaDetailInfoMibsGroup 3 }
myOspfRouterLsaDetailEntry OBJECT-TYPE
SYNTAX MyOspfRouterLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {myOspfLsdbAreaId, myOspfLsdbType,
myOspfLsdbLsid, myOspfLsdbRouterId,
myOspfRouterLsaDetailLinkID
}
::= { myOspfRouterLsaDetailTable 1 }
MyOspfRouterLsaDetailEntry ::=
SEQUENCE{
myOspfRouterLsaDetailLinkID
IpAddress,
myOspfRouterLsaDetailLinkType
INTEGER,
myOspfRouterLsaDetailLinkData
IpAddress,
myOspfRouterLsaDetailTos0Metric
INTEGER
}
myOspfRouterLsaDetailLinkID OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"router lsa's link ID Identifies the object that this router
link connects to. Value depends on the link's Type.
When connecting to an object that also originates an
LSA (i.e., another router or a transit network) the
Link ID is equal to the neighboring LSA's Link
State ID. This provides the key for looking up the neighboring
LSA in the link state database during the routing table
calculation. See Section 12.2 for more details.
Type Link ID
________________________________________
1 Neighboring router's Router ID
2 IP address of Designated Router
3 IP network/subnet number
4 Neighboring router's Router ID
"
::= { myOspfRouterLsaDetailEntry 1 }
myOspfRouterLsaDetailLinkType OBJECT-TYPE
SYNTAX INTEGER{
pointtopointConnectionToAnotherRouter(1),
connectionToaTransitNetwork(2),
connectionToaStubNetwork(3),
virtualLink(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"router lsa's link type
A quick description of the router link. One of the following.
Note that host routes are classified as links to stub networks
with network mask of 0xffffffff."
::= { myOspfRouterLsaDetailEntry 2 }
myOspfRouterLsaDetailLinkData OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Value again depends on the link's Type field. For connections to
stub networks, Link Data specifies the network's IP address
mask. For unnumbered point-to-point connections, it specifies
the interface's MIB-II ifIndex value. For the other link
types it specifies the router interface's IP address. This
latter piece of information is needed during the routing table
build process, when calculating the IP address of the next hop. "
::= { myOspfRouterLsaDetailEntry 3 }
myOspfRouterLsaDetailTos0Metric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"TOS0-specific metric information."
::= { myOspfRouterLsaDetailEntry 4 }
--NetWork Lsa's detail information table
myOspfNetWorkLsaDetailTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfNetWorkLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the NetWork Lsa's detail Infromtion."
::= { myOspfLsaDetailInfoMibsGroup 4 }
myOspfNetWorkLsaDetailEntry OBJECT-TYPE
SYNTAX MyOspfNetWorkLsaDetailEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {myOspfLsdbAreaId, myOspfLsdbType,
myOspfLsdbLsid, myOspfLsdbRouterId,
myOspfNetWorkLsaDetailAttachedRouter
}
::= { myOspfNetWorkLsaDetailTable 1 }
MyOspfNetWorkLsaDetailEntry ::=
SEQUENCE{
myOspfNetWorkLsaDetailAttachedRouter
IpAddress,
myOspfNetWorkLsaDetailNetworkMask
IpAddress
}
myOspfNetWorkLsaDetailAttachedRouter OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The Router IDs of each of the routers attached to the network.
Actually, only those routers that are fully adjacent to the
Designated Router are listed. The Designated Router includes
itself in this list. The number of routers included can be
deduced from the LSA header's length field. "
::= { myOspfNetWorkLsaDetailEntry 1 }
myOspfNetWorkLsaDetailNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address mask for the network. For example, a class A
network would have the mask 0xff000000."
::= { myOspfNetWorkLsaDetailEntry 2 }
--my Ospf Area Lsa Database Summary Table
myOspfAreaLsaDBSumTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfAreaLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPF Area LSA database summary Infromtion."
::= { myOspfLsaDetailInfoMibsGroup 5 }
myOspfAreaLsaDBSumEntry OBJECT-TYPE
SYNTAX MyOspfAreaLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {myOspfAreaLsaDBSumAreaId,
myOspfAreaLsaDBSumLsaType
}
::= { myOspfAreaLsaDBSumTable 1 }
MyOspfAreaLsaDBSumEntry ::=
SEQUENCE{
myOspfAreaLsaDBSumAreaId
IpAddress,
myOspfAreaLsaDBSumLsaType
INTEGER,
myOspfAreaLsaDBSumCounts
Counter32,
myOspfAreaLsaDBSumDeletes
Counter32,
myOspfAreaLsaDBSumMaxage
Counter32
}
myOspfAreaLsaDBSumAreaId OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The area Id."
::= { myOspfAreaLsaDBSumEntry 1 }
myOspfAreaLsaDBSumLsaType OBJECT-TYPE
SYNTAX INTEGER
{ routerLink (1),
networkLink (2),
summaryLink (3),
asSummaryLink (4),
--asExternalLink (5), because in each area,type 5 lsa is no meaning
--it's only meaning in one router
-- multicastLink (6), not implement
nssaExternalLink (7),
subtotal(8)
--subtotal is use for total counter for all type LSA in this area.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the entry's entry type."
::= { myOspfAreaLsaDBSumEntry 2 }
myOspfAreaLsaDBSumCounts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number os this type Lsa in this area ,
if this type Lsa does not exist,this field is 0."
::= { myOspfAreaLsaDBSumEntry 3 }
myOspfAreaLsaDBSumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number os this type Lsa which has been delete in this area ,
if this type Lsa is not been deleted,this field is 0"
::= { myOspfAreaLsaDBSumEntry 4 }
myOspfAreaLsaDBSumMaxage OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" number of this type Lsa which has up to Maxage,
if this type Lsa which has up to Maxage does not exist,
this field is 0"
::= { myOspfAreaLsaDBSumEntry 5 }
--my Ospf Lsa Database total summary table
myOspfLsaDBSumTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"LSA database total summary infromtion in the all areas ."
::= { myOspfLsaDetailInfoMibsGroup 6 }
myOspfLsaDBSumEntry OBJECT-TYPE
SYNTAX MyOspfLsaDBSumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX {
myOspfLsaDBSumLsaType
}
::= { myOspfLsaDBSumTable 1 }
MyOspfLsaDBSumEntry ::=
SEQUENCE{
myOspfLsaDBSumLsaType
INTEGER,
myOspfLsaDBSumCounts
Counter32,
myOspfLsaDBSumDeletes
Counter32,
myOspfLsaDBSumMaxage
Counter32
}
myOspfLsaDBSumLsaType OBJECT-TYPE
SYNTAX INTEGER
{ routerLink (1),
networkLink (2),
summaryTotalLink (3),
asSummaryTotalLink (4),
asExternalLink (5),
-- multicastLink (6), not implement
nssaExternalLink (7),
total(8)
--subtotal is use for total counter for all type LSA in this router.
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the table's entry type."
::= { myOspfLsaDBSumEntry 1 }
myOspfLsaDBSumCounts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"total number of this type Lsa in all area ."
::= { myOspfLsaDBSumEntry 2 }
myOspfLsaDBSumDeletes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" total number of this type Lsa deleted in all area ."
::= { myOspfLsaDBSumEntry 3 }
myOspfLsaDBSumMaxage OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"total number of this type Lsa which has been up to max age in all area "
::= { myOspfLsaDBSumEntry 4 }
-- The OSPF Neighbor Table describes all neighbors in
-- the locality of the subject router.
myOspfNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the neighbor detail infomation ."
REFERENCE
"ospfNbrTable in rfc1850"
::= { myOspfMIBObjects 9 }
myOspfNeighborEntry OBJECT-TYPE
SYNTAX MyOspfNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX { myOspfNbrIpAddr,
myOspfNbrAddressLessIndex
}
::= { myOspfNeighborTable 1 }
MyOspfNeighborEntry ::=
SEQUENCE{
myOspfNbrIpAddr
IpAddress,
myOspfNbrAddressLessIndex
Unsigned32,
myOspfNbrRtrId
RouterID,
myOspfNbrOptions
Unsigned32,
myOspfNbrPriority
DesignatedRouterPriority,
myOspfNbrState
INTEGER,
myOspfNbrEvents
Counter32,
myOspfNbrLsRetransQLen
Gauge32,
myOspfNbmaNbrStatus
RowStatus,
myOspfNbmaNbrPermanence
INTEGER,
myOspfNbrHelloSuppressed
TruthValue,
myOspfNbrDeadTimeDueIn
TimeTicks,
myOspfNbrNeighborUpTime
TimeTicks,
myOspfNbrDR
IpAddress,
myOspfNbrBDR
IpAddress,
myOspfNbrArea
IpAddress,
myOspfNbrRetransmissionNum
Counter32,
myOspfNbrIfState
INTEGER
}
myOspfNbrIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address this neighbor(neighbor's interface IP address)
is using in its IP Source Address. Note that, on addressless
links, this will not be 0.0.0.0, but the ad-
dress of another of the neighbor's interfaces."
::= { myOspfNeighborEntry 1 }
myOspfNbrAddressLessIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"On an interface having an IP Address, zero.
On addressless interfaces, the corresponding
value of ifIndex in the Internet Standard MIB.
On row creation, this can be derived from the
instance."
::= { myOspfNeighborEntry 2 }
myOspfNbrRtrId OBJECT-TYPE
SYNTAX RouterID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 32-bit integer (represented as a type IpAd-
dress) uniquely identifying the neighboring
router in the Autonomous System."
::= { myOspfNeighborEntry 3 }
myOspfNbrOptions OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A Bit Mask corresponding to the neighbor's op-
tions field.
Bit 0, if set, indicates that the system will
operate on Type of Service metrics other than
TOS 0. If zero, the neighbor will ignore all
metrics except the TOS 0 metric.
Bit 1, if set, indicates that the associated
area accepts and operates on external informa-
tion; if zero, it is a stub area.
Bit 2, if set, indicates that the system is ca-
pable of routing IP Multicast datagrams; i.e.,
that it implements the Multicast Extensions to
OSPF.
Bit 3, if set, indicates that the associated
area is an NSSA. These areas are capable of
carrying type 7 external advertisements, which
are translated into type 5 external advertise-
ments at NSSA borders."
REFERENCE
"OSPF Version 2, Section 12.1.2 Options"
::= { myOspfNeighborEntry 4 }
myOspfNbrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The priority of this neighbor in the designat-
ed router election algorithm. The value 0 sig-
nifies that the neighbor is not eligible to be-
come the designated router on this particular
network."
::= { myOspfNeighborEntry 5 }
myOspfNbrState OBJECT-TYPE
SYNTAX INTEGER {
down (1),
attempt (2),
init (3),
twoWay (4),
exchangeMy (5),
exchange (6),
loading (7),
full (8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The State of the relationship with this Neigh-
bor."
REFERENCE
"OSPF Version 2, Section 10.1 Neighbor States"
::= { myOspfNeighborEntry 6 }
myOspfNbrEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this neighbor relationship
has changed state, or an error has occurred."
::= { myOspfNeighborEntry 7 }
myOspfNbrLsRetransQLen OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current length of the retransmission
queue."
::= { myOspfNeighborEntry 8 }
myOspfNbmaNbrStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent."
::= { myOspfNeighborEntry 9 }
myOspfNbmaNbrPermanence OBJECT-TYPE
SYNTAX INTEGER {
dynamic (1), -- learned through protocol
permanent (2) -- configured address
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable displays the status of the en-
try. 'dynamic' and 'permanent' refer to how
the neighbor became known."
::= { myOspfNeighborEntry 10 }
myOspfNbrHelloSuppressed OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Hellos are being suppressed
to the neighbor"
::= { myOspfNeighborEntry 11 }
myOspfNbrDeadTimeDueIn OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"if in this interval ,hello packet is not been received ,
the neighbor is recognized dead.if received,it
will recovery the dead time which has been setted."
::= { myOspfNeighborEntry 12 }
myOspfNbrNeighborUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the time that the neighbor has been up."
::= { myOspfNeighborEntry 13 }
myOspfNbrDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Designated Router of this neighbor."
::= { myOspfNeighborEntry 14 }
myOspfNbrBDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Backup Designated Router of this neighbor."
::= { myOspfNeighborEntry 15 }
myOspfNbrArea OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the area where the neighbor is in."
::= { myOspfNeighborEntry 16 }
myOspfNbrRetransmissionNum OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the Retransmission times."
::= { myOspfNeighborEntry 17 }
myOspfNbrIfState OBJECT-TYPE
SYNTAX INTEGER {
other(0),
designatedRouter (1),
backupDesignatedRouter (2),
otherDesignatedRouter (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The neighbor's interface State which connected to local router."
::= { myOspfNeighborEntry 18 }
--OSPF border routing information
myOspfRouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF MyOspfRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entity's OSPF border routing table."
::= { myOspfMIBObjects 10 }
myOspfRouteEntry OBJECT-TYPE
SYNTAX MyOspfRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A route to a destination."
INDEX {
myOspfRouteDest,
myOspfRouteArea,
myOspfRouteNextHop
}
::= { myOspfRouteTable 1 }
MyOspfRouteEntry ::=
SEQUENCE {
myOspfRouteDest
IpAddress,
myOspfRouteArea
IpAddress,
myOspfRouteNextHop
IpAddress,
myOspfRouteCost
Unsigned32,
myOspfRouteType
INTEGER,
myOspfRouteDRType
INTEGER,
myOspfRouteSpfNo
Counter32
}
myOspfRouteDest OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Router ID of the destination."
::= { myOspfRouteEntry 1 }
myOspfRouteArea OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The area ID of the area from which this route is learned."
::= { myOspfRouteEntry 2 }
myOspfRouteNextHop OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Next hop toward the destination."
::= { myOspfRouteEntry 3 }
myOspfRouteCost OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Cost of using this route."
::= { myOspfRouteEntry 4 }
myOspfRouteDRType OBJECT-TYPE
SYNTAX INTEGER {
abr(1),
asbr(2),
both(3) --abr and asbr
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The router type of the destination;
it is either an ABR or ASBR or both."
::= { myOspfRouteEntry 5 }
myOspfRouteType OBJECT-TYPE
SYNTAX INTEGER {
intral-area-route(1),
inter-area-route(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"this field indicate this route is an intral area route
or inter area route."
::= { myOspfRouteEntry 6 }
myOspfRouteSpfNo OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" The internal number of the shortest path first (SPF) calculation that
installs this route."
::= { myOspfRouteEntry 7 }
-- conformance information
myOspfMIBConformance OBJECT IDENTIFIER ::= { myOspfMIB 2 }
myOspfMIBCompliances OBJECT IDENTIFIER ::= { myOspfMIBConformance 1 }
myOspfMIBGroups OBJECT IDENTIFIER ::= { myOspfMIBConformance 2 }
-- compliance statements
myOspfMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which implement
the My OSPF MIB"
MODULE -- this module
MANDATORY-GROUPS {
myOspfBaseMIBGroup,
myOspfAreaMIBGroup,
myOspfLsaMIBGroup,
myOspfIfMIBGroup,
myOspfVirtMIBGroup,
myOspfNeighborMIBGroup,
myOspfRouteInfoMIBGroup
}
::= { myOspfMIBCompliances 1 }
-- units of conformance
myOspfBaseMIBGroup OBJECT-GROUP
OBJECTS {
myOspfMiniLsaInterval ,
myOspfMiniLsaArrival ,
myOspfAreasNum ,
myOspfNormalAreasNum ,
myOspfStubAreasNum ,
myOspfNssaAreasNum ,
myOspfSpfDelay ,
myOspfSpfHoldTime ,
myOspfAutoCostRefBandWidthRef ,
myOspfLsaGroupPacing ,
myOspfInterDistance ,
myOspfIntraDistance ,
myOspfExternDistance ,
myOspfLogAdjChangeNotify ,
myOspfPassiveStatus ,
myOspfRFC1583Compatibility ,
myOspfRouteRedisDefMetricVal
}
STATUS current
DESCRIPTION
"A collection of general objects providing OSPF managment."
::= { myOspfMIBGroups 1 }
myOspfAreaMIBGroup OBJECT-GROUP
OBJECTS {
myOspfAreaId,
myOspfAuthType,
myOspfImportAsExtern,
myOspfSpfRuns,
myOspfAreaBdrRtrCount,
myOspfAsBdrRtrCount,
myOspfAreaLsaCount,
myOspfAreaLsaCksumSum,
myOspfAreaSummary,
myOspfAreaStatus,
myOspfAreaInterfaceNum,
myOspfAreaNssaIsRedistribution,
myOspfAreaNssaIsDefInfoOriginate,
myOspfNetWorkAreaID,
myOspfNetWorkAddress,
myOspfNetWorkMask,
myOspfNetWorkStatus
}
STATUS current
DESCRIPTION
"A collection of area objects providing OSPF managment."
::= { myOspfMIBGroups 2 }
myOspfLsaMIBGroup OBJECT-GROUP
OBJECTS {
myOspfLsdbAreaId,
myOspfLsdbType,
myOspfLsdbLsid,
myOspfLsdbRouterId,
myOspfLsdbSequence,
myOspfLsdbAge,
myOspfLsdbChecksum,
myOspfLsdbAdvertisement,
myOspfLsdbLinkNum,
myOspfLsdbPacketLength,
myOspfSummaryLsaNetworkMask,
myOspfSummaryLsaTos0Metric,
myOspfNssaLsaDetailMetricType,
myOspfNssaLsaDetailForwardAddr ,
myOspfNssaLsaDetailRouteTag ,
myOspfLsdbOption,
myOspfExtLsdbType,
myOspfExtLsdbLsid,
myOspfExtLsdbRouterId,
myOspfExtLsdbSequence,
myOspfExtLsdbAge,
myOspfExtLsdbChecksum,
myOspfExtLsdbAdvertisement,
myOspfExtLsdbNetworkMask,
myOspfExtLsdbMetricType,
myOspfExtLsdbForwardAddr,
myOspfExtLsdbRouteTag,
myOspfExtLsdbMetric,
myOspfExtLsdbOption,
myOspfExtLsdbPacketLength,
myOspfRouterLsaDetailLinkID,
myOspfRouterLsaDetailLinkType,
myOspfRouterLsaDetailLinkData,
myOspfRouterLsaDetailTos0Metric,
myOspfNetWorkLsaDetailAttachedRouter,
myOspfNetWorkLsaDetailNetworkMask,
myOspfAreaLsaDBSumAreaId,
myOspfAreaLsaDBSumLsaType,
myOspfAreaLsaDBSumCounts ,
myOspfAreaLsaDBSumDeletes,
myOspfAreaLsaDBSumMaxage,
myOspfLsaDBSumLsaType,
myOspfLsaDBSumCounts,
myOspfLsaDBSumDeletes,
myOspfLsaDBSumMaxage
}
STATUS current
DESCRIPTION
"A collection of OSPF Link State Database objects providing OSPF managment."
::= { myOspfMIBGroups 3 }
myOspfIfMIBGroup OBJECT-GROUP
OBJECTS {
myOspfIfIpAddress,
myOspfAddressLessIf,
myOspfIfAreaId,
myOspfIfType,
myOspfIfAdminStat,
myOspfIfRtrPriority,
myOspfIfTransitDelay,
myOspfIfRetransInterval,
myOspfIfHelloInterval,
myOspfIfRtrDeadInterval,
myOspfIfPollInterval,
myOspfIfState,
myOspfIfDesignatedRouter,
myOspfIfBackupDesignatedRouter,
myOspfIfEvents,
myOspfIfAuthType,
myOspfIfAuthKey,
myOspfIfStatus,
myOspfIfMulticastForwarding,
myOspfIfDemand,
myOspfIfDatabaseFilterAllOut,
myOspfIfDesignateRouterId ,
myOspfIfBackupDesignateRouterId ,
-- myOspfIfMd5AuthKeyId,
myOspfIfWaitInternal,
myOspfIfPassiveStatus,
myOspfIfCurrentUsedMd5AuthKeyId,
myOspfIfMd5AuthKeyIf,
myOspfIfMd5AuthKeyId,
myOspfIfMd5AuthKey,
myOspfIfMd5AuthKeySt
}
STATUS current
DESCRIPTION
"A collection of OSPF interface managment."
::= { myOspfMIBGroups 4 }
myOspfVirtMIBGroup OBJECT-GROUP
OBJECTS {
myOspfVirtIfAreaId,
myOspfVirtIfNeighbor,
myOspfVirtIfTransitDelay,
myOspfVirtIfRetransInterval,
myOspfVirtIfHelloInterval,
myOspfVirtIfRtrDeadInterval,
myOspfVirtIfState,
myOspfVirtIfEvents,
myOspfVirtIfAuthType,
myOspfVirtIfAuthKey,
myOspfVirtIfStatus,
myOspfVirtCost,
myOspfVirtNativeIfIndex,
myOspfVirtLinkState,
myOspfVirtHelloDueIn,
myOspfVirtIfMd5AuthKeyAreaId,
myOspfVirtIfMd5AuthKeyNeighbor,
myOspfVirtIfMd5AuthKeyId,
myOspfVirtIfMd5AuthKey,
myOspfVirtIfMd5AuthKeySt,
myOspfVirtCurrentUsedMd5AuthKeyId
}
STATUS current
DESCRIPTION
"A collection of OSPF Virtual Link managment."
::= { myOspfMIBGroups 5 }
myOspfNeighborMIBGroup OBJECT-GROUP
OBJECTS {
myOspfNbrIpAddr,
myOspfNbrAddressLessIndex,
myOspfNbrRtrId,
myOspfNbrOptions,
myOspfNbrPriority,
myOspfNbrState,
myOspfNbrEvents,
myOspfNbrLsRetransQLen,
myOspfNbmaNbrStatus,
myOspfNbmaNbrPermanence,
myOspfNbrHelloSuppressed,
myOspfNbrDeadTimeDueIn,
myOspfNbrNeighborUpTime,
myOspfNbrDR,
myOspfNbrBDR,
myOspfNbrArea,
myOspfNbrRetransmissionNum
}
STATUS current
DESCRIPTION
"A collection of OSPF Neighbor information."
::= { myOspfMIBGroups 6 }
myOspfRouteInfoMIBGroup OBJECT-GROUP
OBJECTS {
myOspfRouteType,
myOspfRouteDest,
myOspfRouteNextHop,
myOspfRouteCost,
myOspfRouteDRType,
myOspfRouteArea,
myOspfRouteSpfNo
}
STATUS current
DESCRIPTION
"A collection of OSPF route information."
::= { myOspfMIBGroups 7 }
-- -------------------------------------------------------------
-- Compliance statements
-- -------------------------------------------------------------
ospfMIBConformance OBJECT IDENTIFIER ::= { myOspfMIB 3 }
ospfMIBCompliances OBJECT IDENTIFIER ::= { ospfMIBConformance 1 }
ospfExternCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for device support of OSPF
services."
MODULE
-- OBJECT ospfASBdrRtrStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfTOSSupport
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfExtLsdbLimit
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfMulticastExtensions
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfExitOverflowInterval
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfDemandExtensions
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfIfAreaId
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfIfStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Create access is not required."
--
--
-- OBJECT ospfStubMetric
-- MIN-ACCESS read-write
-- DESCRIPTION "Create access is not required."
--
-- OBJECT ospfStubStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfStubMetricType
-- MIN-ACCESS read-write
-- DESCRIPTION "Create access is not required."
--
-- OBJECT ospfIfAdminStat
-- MIN-ACCESS read-only
-- DESCRIPTION "Write access is not required."
--
-- OBJECT ospfNbmaNbrStatus
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfNbrPriority
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfIfPollInterval
-- MIN-ACCESS read-only
-- DESCRIPTION "Read-create access is not required."
--
-- OBJECT ospfIfTransitDelay
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfIfRetransInterval
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfVirtIfTransitDelay
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
--
-- OBJECT ospfIfType
-- SYNTAX INTEGER {
-- broadcast (1),
-- nbma (2),
-- pointToPoint (3),
-- pointToMultipoint (5),
-- loopback(6)
-- }
-- DESCRIPTION "add type 'loopback'."
--
-- OBJECT ospfVirtIfRetransInterval
-- SYNTAX Unsigned32 (1..65535)
-- DESCRIPTION "Range of value is changed."
OBJECT myOspfVirtIfRtrDeadInterval
SYNTAX PositiveInteger
DESCRIPTION "default value change from 60 to 40."
::= { ospfMIBCompliances 1 }
END
View Git Blame Copy Permalink