WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/ciscosb/CISCO-STP-EXTENSIONS-MIB

5029 lines
195 KiB
Plaintext
Raw Permalink Blame History

-- *****************************************************************
-- CISCO-STP-EXTENSIONS-MIB
--
-- August 1997, Fei Xu
--
-- Copyright (c) 1997-2013 by Cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************
CISCO-STP-EXTENSIONS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Counter32,
Integer32,
Unsigned32,
NOTIFICATION-TYPE
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
TruthValue,
TimeStamp,
DisplayString,
RowStatus,
TEXTUAL-CONVENTION
FROM SNMPv2-TC
-- vlanTrunkPortEntry,
-- VlanIndex,
-- vtpVlanEntry,
-- vtpVlanEditEntry
-- FROM CISCO-VTP-MIB
dot1dStpPortEntry
FROM BRIDGE-MIB
ciscoMgmt
FROM CISCO-SMI;
ciscoStpExtensionsMIB MODULE-IDENTITY
LAST-UPDATED "201303070000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-wbu@cisco.com"
DESCRIPTION
"The MIB module for managing Cisco extensions to
the 802.1D Spanning Tree Protocol (STP)."
REVISION "201303070000Z"
DESCRIPTION
"Added one new value network(5) to stpxFastStartPortMode."
REVISION "200512200000Z"
DESCRIPTION
"Added bit value rstp(5) to stpxSMSTPortStatus and
dispute(4) to stpxRPVSTPortStatus."
REVISION "200504120000Z"
DESCRIPTION
"Changed the description clauses of stpxMSTMaxHopCount
and stpxMSTInstanceRemainingHopCount.
Added StpxMSTConfigurationDigest textual convention.
Deprecated stpxMSTGroup3 and added the following groups:
stpxRSTPTransmitHoldCountGroup,
stpxSMSTPortMSTModeGroup, stpxSMSTMaxHopCountGroup,
stpxSMSTConfigDigestGroup and stpxMSTGroup4.
Added bit dispute(4) into the BITS syntax of
stpxSMSTPortStatus.
Deprecated stpxMIBCompliance11 and added
stpxMIBCompliance12."
REVISION "200407210000Z"
DESCRIPTION "Added stpxPathCostOperModeGroup
and changed the decription of
stpxSpanningTreePathCostMode."
REVISION "200404080000Z"
DESCRIPTION
"Added stpxSMSTInstanceCISTGroup.
Added 3 new bit values into the BITS syntax
of stpxNotificationEnable:
inconsistency(2), rootInconsistency(3),
and loopInconsistency(4)."
REVISION "200401140000Z"
DESCRIPTION
"Deprecated stpxMSTGroup2 and
stpxPreferredMSTInstancesGroup.
Added stpxMSTGroup3, stpxSMSTGroup,
stpxSMSTInstanceGroup, stpxSMSTInstanceEditGroup,
stpxSMSTPortStatusGroup, stpxSMSTPortHelloTimeGroup.
Added one new value master(7) to stpxMSTPortRoleValue
and stpxRSTPPortRoleValue. Added 2 new unused bit
value into the BITS syntax of stpxRPVSTPortStatus."
REVISION "200310230000Z"
DESCRIPTION
"Added stpxExtendedSysIDGroup,
stpxNotificationEnableGroup, and
stpxFastStartOperModeGroup."
REVISION "200207110000Z"
DESCRIPTION
"Added Rapid Spanning Tree Protocol support.
Added stpxUplinkFastOperEnabled and
stpxBackboneFastOperEnabled objects.
Replaced stpxMSTPortAdminLinkType,
stpxMSTPortOperLinkType,
stpxMSTPortProtocolMigration
with stpxRSTPPortAdminLinkType,
stpxRSTPPortOperLinkType and
stpxRSTPPortProtocolMigration
defined in stpxRSTPPortTable.
Replaced stpxMSTPortRoleTable with
stpxRSTPPortRoleTable. Added stpxRPVSTPortTable."
REVISION "200112060000Z"
DESCRIPTION
"Added per port Bpdu Guard and Bpdu Filter
mode configuration support. Modified the
description of stpxUplinkFastEnabled and
stpxUplinkStationLearningGenRate for MST
support. "
REVISION "200109140000Z"
DESCRIPTION
"Added MST support, Loop Guard Global Default mode
support and Fast Start Global Default mode support.
Deprecated stpxFastStartPortEnable and
stpxLoopGuardConfigEnabled objects. Changed description
of stpxUplinkFastEnabled, stpxUplinkFastTransitions,
stpxUplinkStationLearningGenRate,
stpxUplinkStationLearningFrames objects for MST support."
REVISION "200106200000Z"
DESCRIPTION
"Added BPDU Skewing feature support and modified
the SYNTAX clause of stpxUplinkStationLearningGenRate."
REVISION "200104120000Z"
DESCRIPTION
"Added PVST+ VLAN Configuration, MISTP to VLAN mapping,
Loopguard, and Port Fast Start support."
REVISION "200005230000Z"
DESCRIPTION
"Added Long Spanning Tree Path Cost Mode support."
REVISION "200003210000Z"
DESCRIPTION
"Added Rootguard, 4k VLAN and MISTP support."
REVISION "9711101200Z"
DESCRIPTION
"Additional objects to support SSTP."
REVISION "9708191200Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 82 }
stpxObjects OBJECT IDENTIFIER ::= { ciscoStpExtensionsMIB 1 }
stpxUplinkFastObjects OBJECT IDENTIFIER ::= { stpxObjects 1 }
stpxVlanObjects OBJECT IDENTIFIER ::= { stpxObjects 2 }
stpxInconsistencyObjects
OBJECT IDENTIFIER ::= { stpxObjects 3 }
-- stpxBackboneFastObjects
-- OBJECT IDENTIFIER ::= { stpxObjects 4 }
--
-- stpxRootGuardObjects OBJECT IDENTIFIER ::= { stpxObjects 5 }
--
-- stpxSpanningTreeObjects OBJECT IDENTIFIER ::= { stpxObjects 6 }
--
-- stpxMISTPObjects OBJECT IDENTIFIER ::= { stpxObjects 7 }
--
-- stpxLoopGuardObjects OBJECT IDENTIFIER ::= { stpxObjects 8 }
--
-- stpxFastStartObjects OBJECT IDENTIFIER ::= { stpxObjects 9 }
--
-- stpxBpduSkewingObjects OBJECT IDENTIFIER ::= { stpxObjects 10 }
--
-- stpxMSTObjects OBJECT IDENTIFIER ::= { stpxObjects 11 }
--
-- stpxRSTPObjects OBJECT IDENTIFIER ::= { stpxObjects 12 }
--
-- stpxRPVSTObjects OBJECT IDENTIFIER ::= { stpxObjects 13 }
--
-- stpxSMSTObjects OBJECT IDENTIFIER ::= { stpxObjects 14 }
--
-- stpxNotifications OBJECT IDENTIFIER ::= { ciscoStpExtensionsMIB 2 }
--
-- t e x t u a l c o n v e n t i o n s
--
-- changes notes from original file:
-- From CISCO-VTP-MIB.mib - change range from 0..1023 to 1..4094
-- change description
VlanIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The VLAN-id of a VLAN."
SYNTAX INTEGER (1..4094)
-- All unneeded lines are remarked
-- All remarks in remarked line have changed to - -
-- end of changes notes from original file
--
-- StpxMSTConfigurationDigest ::= TEXTUAL-CONVENTION
-- DISPLAY-HINT "1x"
-- STATUS current
-- DESCRIPTION
-- "Represents an MST configuration digest."
-- SYNTAX OCTET STRING (SIZE (16))
--
--
-- UplinkFast capability
--
--
-- stpxUplinkFastEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "An indication of whether the UplinkFast capability is
-- administratively enabled on the device.
--
-- If the platform does not support configuration of this
-- object when the object value of stpxSpanningTreeType is
-- mst(4), then this object is not instantiated."
-- ::= { stpxUplinkFastObjects 1 }
--
-- stpxUplinkFastTransitions OBJECT-TYPE
-- SYNTAX Counter32
-- UNITS "transitions"
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The cumulative number of UplinkFast transitions (from
-- the STP 'Blocking' state directly to the STP 'Forwarding'
-- state). All transitions are included in this counter,
-- irrespective of the instance of the Spanning Tree
-- Protocol on which they occur.
--
-- If the platform supports the stpxUplinkFastOperEnabled
-- object, then this object is not instantiated when the
-- object value of stpxUplinkFastOperEnabled is false(2).
-- If the platform does not support the
-- stpxUplinkFastOperEnabled object, then this object is
-- not instantiated when the object value of
-- stpxSpanningTreeType is mst(4)."
-- ::= { stpxUplinkFastObjects 2 }
--
-- stpxUplinkStationLearningGenRate OBJECT-TYPE
-- SYNTAX Integer32 (0..32000)
-- UNITS "frames"
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The maximum number of station-learning frames that this
-- device will generate in each 100 milli-second period after
-- a UplinkFast transition. By configuring this object, the
-- network administrator can limit the rate at which
-- station-learning frames are generated.
--
-- If the platform does not support configuration of this
-- object when the object value of stpxSpanningTreeType is
-- mst(4), then this object is not instantiated."
-- ::= { stpxUplinkFastObjects 3 }
--
-- stpxUplinkStationLearningFrames OBJECT-TYPE
-- SYNTAX Counter32
-- UNITS "frames"
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The cumulative number of station-learning frames generated
-- due to UplinkFast transitions. All generated
-- station-learning frames are included in this counter,
-- irrespective of the instance of the Spanning Tree Protocol
-- on which the UplinkFast transition occurred.
--
-- If the platform supports the stpxUplinkFastOperEnabled
-- object, then this object is not instantiated when the
-- object value of stpxUplinkFastOperEnabled is false(2).
-- If the platform does not support the
-- stpxUplinkFastOperEnabled object, then this object is
-- not instantiated when the object value of
-- stpxSpanningTreeType is mst(4)."
-- ::= { stpxUplinkFastObjects 4 }
--
-- stpxUplinkFastOperEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "An indication of whether the UplinkFast capability is
-- operationally enabled on the device."
-- ::= { stpxUplinkFastObjects 5 }
--
--
--
-- Preferred VLANs for Load-Sharing across VLAN Trunk Ports
--
--
-- stpxPreferredVlansTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxPreferredVlansEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The table containing indications of which VLANs are
-- preferred on which VLAN trunk ports. The preferred
-- VLANs on a trunk port have a lower Path Cost value
-- compared with the VLANs on the trunk not in the
-- preferred list. If the value of stpxSpanningTreeType
-- is neither pvstPlus(1) nor rapidPvstPlus(5), the
-- configuration in this table has no effect. "
-- ::= { stpxVlanObjects 1 }
--
-- stpxPreferredVlansEntry OBJECT-TYPE
-- SYNTAX StpxPreferredVlansEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An entry indicating which VLANs are preferred on a
-- specific VLAN trunk port."
-- AUGMENTS { vlanTrunkPortEntry }
-- ::= { stpxPreferredVlansTable 1 }
--
-- StpxPreferredVlansEntry ::=
-- SEQUENCE {
-- stpxPreferredVlansMap OCTET STRING,
-- stpxPreferredVlansMap2k OCTET STRING,
-- stpxPreferredVlansMap3k OCTET STRING,
-- stpxPreferredVlansMap4k OCTET STRING
-- }
--
-- stpxPreferredVlansMap OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (128))
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN in the
-- management domain on this trunk port. The first octet
-- corresponds to VLANs with VlanIndex values of 0 through 7;
-- the second octet to VLANs 8 through 15; etc. The most
-- significant bit of each octet corresponds to the lowest
-- value VlanIndex in that octet.
--
-- For each VLAN, if it is preferred on this trunk port, then
-- the bit corresponding to that VLAN is set to '1'.
-- The default value is 128 bytes of zeros.
--
-- To avoid conflicts between overlapping partial updates by
-- multiple managers, i.e., updates which modify only a portion
-- of an instance of this object (e.g., enable/disable a single
-- VLAN on the trunk port), any SNMP Set operation accessing an
-- instance of this object should also write the value of
-- vlanTrunkPortSetSerialNo."
-- ::= { stpxPreferredVlansEntry 1 }
--
-- stpxPreferredVlansMap2k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for VLANS
-- with VlanIndex values of 1024 through 2047 in the management
-- domain on this trunk port. The first octet corresponds to
-- VLANs with VlanIndex values of 1024 through 1031;
-- the second octet to VLANs 1032 through 1039; etc.
-- The most significant bit of each octet corresponds to the
-- lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is preferred on this trunk port, then
-- the bit corresponding to that VLAN is set to '1'.
-- The default value is 128 bytes of zeros.
--
-- To avoid conflicts between overlapping partial updates by
-- multiple managers, i.e., updates which modify only a portion
-- of an instance of this object (e.g., enable/disable a single
-- VLAN on the trunk port), any SNMP Set operation accessing an
-- instance of this object should also write the value of
-- vlanTrunkPortSetSerialNo."
-- ::= { stpxPreferredVlansEntry 2 }
--
-- stpxPreferredVlansMap3k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for VLANS
-- with VlanIndex values of 2048 through 3071 in the management
-- domain on this trunk port. The first octet corresponds to
-- VLANs with VlanIndex values of 2048 through 2055;
-- the second octet to VLANs 2056 through 2063; etc.
-- The most significant bit of each octet corresponds to the
-- lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is preferred on this trunk port, then
-- the bit corresponding to that VLAN is set to '1'.
-- The default value is 128 bytes of zeros.
--
-- To avoid conflicts between overlapping partial updates by
-- multiple managers, i.e., updates which modify only a portion
-- of an instance of this object (e.g., enable/disable a single
-- VLAN on the trunk port), any SNMP Set operation accessing an
-- instance of this object should also write the value of
-- vlanTrunkPortSetSerialNo."
-- ::= { stpxPreferredVlansEntry 3 }
--
-- stpxPreferredVlansMap4k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for VLANS
-- with VlanIndex values of 3072 through 4095 in the management
-- domain on this trunk port. The first octet corresponds to
-- VLANs with VlanIndex values of 3072 through 3079;
-- the second octet to VLANs 3080 through 3087; etc.
-- The most significant bit of each octet corresponds to the
-- lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is preferred on this trunk port, then
-- the bit corresponding to that VLAN is set to '1'.
-- The default value is 128 bytes of zeros.
--
-- To avoid conflicts between overlapping partial updates by
-- multiple managers, i.e., updates which modify only a portion
-- of an instance of this object (e.g., enable/disable a single
-- VLAN on the trunk port), any SNMP Set operation accessing an
-- instance of this object should also write the value of
-- vlanTrunkPortSetSerialNo."
-- ::= { stpxPreferredVlansEntry 4 }
--
--
-- Spanning Tree Protocol PVST+ VLAN Configuration
--
-- stpxPVSTVlanTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxPVSTVlanEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION "A list of Virtual LAN entries containing
-- information for Spanning Tree PVST+ protocol.
-- An entry will exist for each VLAN existing on
-- the device."
-- ::= { stpxVlanObjects 2 }
--
-- stpxPVSTVlanEntry OBJECT-TYPE
-- SYNTAX StpxPVSTVlanEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION "An entry containing Spanning Tree PVST+ Protocol
-- information for a particular Virtual LAN."
-- INDEX { stpxPVSTVlanIndex }
-- ::= { stpxPVSTVlanTable 1 }
--
-- StpxPVSTVlanEntry ::=
-- SEQUENCE {
-- stpxPVSTVlanIndex
-- VlanIndex,
-- stpxPVSTVlanEnable
-- INTEGER
-- }
--
-- stpxPVSTVlanIndex OBJECT-TYPE
-- SYNTAX VlanIndex
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION "An index value that uniquely identifies the
-- Virtual LAN associated with this information."
-- ::= { stpxPVSTVlanEntry 1 }
--
-- stpxPVSTVlanEnable OBJECT-TYPE
-- SYNTAX INTEGER { enabled(1),
-- disabled(2),
-- notApplicable(3) - - read-only
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION "Indicates whether Spanning Tree PVST+
-- Protocol is enabled for this Virtual LAN. If
-- Spanning Tree PVST+ Protocol is not supported
-- on this VLAN, then notApplicable(3) will be
-- returned while retrieving the object value for
-- this VLAN.
--
-- If the device only supports a single global
-- Spanning Tree PVST+ Protocol enable/disable
-- for all the existing VLANs, then the object
-- value assigned to this VLAN will be applied
-- to the object values of all the instances
-- in this table which do not have the value
-- of notApplicable(3).
--
-- If the value of stpxSpanningTreeType is neither
-- pvstPlus(1) nor rapidPvstPlus(5), then the value
-- of stpxPVSTVlanEnable for this VLAN can not be
-- changed."
-- DEFVAL { enabled }
-- ::= { stpxPVSTVlanEntry 2 }
--
--
--
-- Objects to support Cisco's Shared Spanning Tree Protocol (SSTP).
--
stpxInconsistencyTable OBJECT-TYPE
SYNTAX SEQUENCE OF StpxInconsistencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing a list of the ports for which
a particular VLAN's Spanning Tree has been found to
have an inconsistency. Two types of inconsistency
are discovered: 1) an inconsistency where two different
port types have been plugged together; and 2) an
inconsistency where different switches have different
PVIDs for the same link."
::= { stpxInconsistencyObjects 1 }
stpxInconsistencyEntry OBJECT-TYPE
SYNTAX StpxInconsistencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A VLAN on a particular port for which a Spanning Tree
inconsistency is currently in effect."
INDEX { stpxVlanIndex, stpxPortIndex }
::= { stpxInconsistencyTable 1 }
StpxInconsistencyEntry ::= SEQUENCE {
stpxVlanIndex VlanIndex,
stpxPortIndex Integer32,
stpxInconsistentState BITS
}
stpxVlanIndex OBJECT-TYPE
SYNTAX VlanIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VLAN id of the VLAN."
::= { stpxInconsistencyEntry 1 }
stpxPortIndex OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of dot1dBasePort (i.e. dot1dBridge.1.4)
for the bridge port."
REFERENCE
"dot1dBasePort is defined in RFC1493."
::= { stpxInconsistencyEntry 2 }
stpxInconsistentState OBJECT-TYPE
SYNTAX BITS {
typeInconsistent(0), -- a port-type inconsistency
pvidInconsistent(1) -- a PVID inconsistency
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The types of inconsistency which have been discovered on
this port for this VLAN's Spanning Tree.
When this object exists, the value of the corresponding
instance of the Bridge MIB's dot1dStpPortState object will
be 'broken(6)'."
REFERENCE
"dot1dStpPortState is defined in RFC-1493."
::= { stpxInconsistencyEntry 3 }
--
-- BackboneFast capability
--
--
-- stpxBackboneFastEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "An indication of whether the BackboneFast capability is
-- administratively enabled on the device."
-- ::= { stpxBackboneFastObjects 1 }
--
-- stpxBackboneFastInInferiorBPDUs OBJECT-TYPE
-- SYNTAX Counter32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The number of inferior BPDUs received by the switch
-- since the stpxBackboneFastOperEnabled has
-- become true(1). If the value of
-- stpxBackboneFastOperEnabled is false(2), then this
-- mib object will have a value of 0."
--
-- ::= { stpxBackboneFastObjects 2 }
--
-- stpxBackboneFastInRLQRequestPDUs OBJECT-TYPE
-- SYNTAX Counter32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The number of Root Link Query request PDUs received by the
-- switch since the stpxBackboneFastOperEnabled has become
-- true(1). If the value of stpxBackboneFastOperEnabled is
-- false(2), then this mib object will have a value of 0."
--
-- ::= { stpxBackboneFastObjects 3 }
--
-- stpxBackboneFastInRLQResponsePDUs OBJECT-TYPE
-- SYNTAX Counter32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The number of Root Link Query response PDUs received by the
-- switch since the stpxBackboneFastOperEnabled has become
-- true(1). If the value of stpxBackboneFastOperEnabled is
-- false(2), then this mib object will have a value of 0."
-- ::= { stpxBackboneFastObjects 4 }
--
-- stpxBackboneFastOutRLQRequestPDUs OBJECT-TYPE
-- SYNTAX Counter32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The number of Root Link Query request PDUs transmitted by
-- the switch since the stpxBackboneFastOperEnabled has become
-- true(1). If the value of stpxBackboneFastOperEnabled is
-- false(2), then this mib object will have a value of 0."
--
-- ::= { stpxBackboneFastObjects 5 }
--
-- stpxBackboneFastOutRLQResponsePDUs OBJECT-TYPE
-- SYNTAX Counter32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The number of Root Link Query response PDUs transmitted by
-- the switch since the stpxBackboneFastOperEnabled has become
-- true(1). If the value of stpxBackboneFastOperEnabled is
-- false(2), then this mib object will have a value of 0."
--
-- ::= { stpxBackboneFastObjects 6 }
--
-- stpxBackboneFastOperEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "An indication of whether the BackboneFast capability is
-- operationally enabled on the device."
-- ::= { stpxBackboneFastObjects 7 }
--
--
-- STP Root Guard Capability
--
--
-- stpxRootGuardConfigTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxRootGuardConfigEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports for which
-- Spanning Tree RootGuard capability can be configured."
-- ::= { stpxRootGuardObjects 1 }
--
-- stpxRootGuardConfigEntry OBJECT-TYPE
-- SYNTAX StpxRootGuardConfigEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A bridge port for which Spanning Tree RootGuard
-- capability can be configured."
-- INDEX { stpxRootGuardConfigPortIndex }
-- ::= { stpxRootGuardConfigTable 1 }
--
-- StpxRootGuardConfigEntry ::= SEQUENCE {
-- stpxRootGuardConfigPortIndex Integer32,
-- stpxRootGuardConfigEnabled TruthValue
-- }
--
-- stpxRootGuardConfigPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxRootGuardConfigEntry 1 }
--
-- stpxRootGuardConfigEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "An indication of whether the RootGuard capability is
-- enabled on this port or not. This configuration will be
-- applied to all Spanning Tree instances in which this port
-- exists."
-- DEFVAL { false }
-- ::= { stpxRootGuardConfigEntry 2 }
--
-- stpxRootInconsistencyTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxRootInconsistencyEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports for which
-- a particular Spanning Tree instance has been found
-- to have an root-inconsistency. The agent creates a new
-- entry in this table whenever it detects a new
-- root-inconsistency, and deletes entries
-- when/soon after the inconsistency is no longer present."
-- ::= { stpxRootGuardObjects 2 }
--
-- stpxRootInconsistencyEntry OBJECT-TYPE
-- SYNTAX StpxRootInconsistencyEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A Spanning Tree instance on a particular port for
-- which a Spanning Tree root-inconsistency is currently
-- in effect."
-- INDEX { stpxRootInconsistencyIndex, stpxRootInconsistencyPortIndex }
-- ::= { stpxRootInconsistencyTable 1 }
--
-- StpxRootInconsistencyEntry ::= SEQUENCE {
-- stpxRootInconsistencyIndex Integer32,
-- stpxRootInconsistencyPortIndex Integer32,
-- stpxRootInconsistencyState TruthValue
-- }
--
-- stpxRootInconsistencyIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The Spanning Tree instance id, such as the VLAN id
-- of the VLAN if the object value of stpxSpanningTreeType
-- is pvstPlus(1) or rapidPvstPlus(5)."
-- ::= { stpxRootInconsistencyEntry 1 }
--
-- stpxRootInconsistencyPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxRootInconsistencyEntry 2 }
--
--
-- stpxRootInconsistencyState OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates whether the port on a particular Spanning
-- Tree instance is currently in root-inconsistent
-- state or not."
-- ::= { stpxRootInconsistencyEntry 3 }
--
--
--
-- stpxSpanningTreeObjects
--
--
-- stpxSpanningTreeType OBJECT-TYPE
-- SYNTAX INTEGER {
-- pvstPlus(1),
-- mistp(2),
-- mistpPvstPlus(3),
-- mst(4),
-- rapidPvstPlus(5)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The actual mode of spanning tree protocol runs
-- on the device. It can be one of the following:
--
-- pvstPlus - - PVST+ (Per VLAN Spanning Tree+ Protocol).
--
-- mistp - - MISTP (Multi Instance Spanning Tree Protocol).
--
-- mistpPvstPlus - - MISTP with the tunneling scheme
-- enabled for PVST+.
--
-- mst - - IEEE 802.1s Multiple Spanning Tree (MST)
-- with IEEE 802.1w Rapid Spanning Tree Protocol
-- (RSTP).
--
-- rapidPvstPlus - - IEEE 802.1w Rapid Spanning Tree
-- Protocol (RSTP) for all vlans in PVST+.
--
-- When the value of this MIB object gets changed, the
-- network connectivity would be affected and the
-- connectivity to this device would also be lost
-- temporarily."
-- DEFVAL { pvstPlus }
-- ::= { stpxSpanningTreeObjects 1}
--
-- stpxSpanningTreePathCostMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- short(1), - - 16 bits spanning tree path
-- - - cost mode
-- long(2) - - 32 bits spanning tree path
-- - - cost mode
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the administrative spanning tree path cost mode
-- configured on device."
--
-- DEFVAL { short }
-- ::= { stpxSpanningTreeObjects 2 }
--
--
-- stpxLongStpPortPathCostTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxLongStpPortPathCostEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing the spanning tree port path cost
-- configuration when stpxSpanningTreePathCostOperMode is
-- long(2).
--
-- If the value of stpxSpanningTreePathCostOperMode is
-- short(1), this table is not instantiated."
-- ::= { stpxSpanningTreeObjects 3 }
--
-- stpxLongStpPortPathCostEntry OBJECT-TYPE
-- SYNTAX StpxLongStpPortPathCostEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A conceptual row containing the spanning tree port path cost
-- configuration."
-- AUGMENTS { dot1dStpPortEntry }
-- ::= { stpxLongStpPortPathCostTable 1 }
--
-- StpxLongStpPortPathCostEntry ::= SEQUENCE {
-- stpxLongStpPortPathCost Unsigned32
-- }
--
-- stpxLongStpPortPathCost OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The contribution of this port to the path cost (in 32
-- bits value) of paths towards the spanning tree root which
-- include this port.
--
-- This object is used to configure the spanning tree port
-- path cost in 32 bits value range when the
-- stpxSpanningTreePathCostOperMode is long(2).
--
-- If the stpxSpanningTreePathCostOperMode is short(1), this
-- MIB object is not instantiated."
-- ::= { stpxLongStpPortPathCostEntry 1}
--
-- stpxExtendedSysIDAdminEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates whether Extended System ID feature
-- is administratively enabled on the device or not."
-- REFERENCE
-- "IEEE 802.1t."
-- ::= { stpxSpanningTreeObjects 4 }
--
-- stpxExtendedSysIDOperEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates whether Extended System ID feature
-- is operationaly enabled on the device or not.
--
-- If the value of this object is true(1), then
-- the accepted values for dot1dStpPriority
-- in BRIDGE-MIB should be multiples of 4096 plus
-- bridge instance ID, such as VlanIndex. Changing
-- this object value might cause the values of
-- dot1dBaseBridgeAddress and dot1dStpPriority
-- in BRIDGE-MIB to be changed also."
-- REFERENCE
-- "IEEE 802.1t."
-- ::= { stpxSpanningTreeObjects 5 }
--
-- stpxNotificationEnable OBJECT-TYPE
-- SYNTAX BITS {
-- newRoot(0),
-- topologyChange(1),
-- inconsistency(2),
-- rootInconsistency(3),
-- loopInconsistency(4)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates whether a specified notification is enabled or not.
-- If a bit corresponding to a notification is set to 1, then
-- the specified notification can be generated.
--
-- newRoot - - the newRoot notification as defined in BRIDGE-MIB.
--
-- topologyChange - - the topologyChange notification as
-- defined in BRIDGE-MIB.
--
-- inconsistency - - the stpxInconsistencyUpdate notification.
--
-- rootInconsistency - - the stpxRootInconsistencyUpdate
-- notification.
--
-- loopInconsistency - - the stpxLoopInconsistencyUpdate
-- notification."
-- ::= { stpxSpanningTreeObjects 6 }
--
-- stpxSpanningTreePathCostOperMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- short(1), - - 16 bits spanning tree path
-- - - cost mode
-- long(2) - - 32 bits spanning tree path
-- - - cost mode
-- }
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicate the operational spanning tree path cost mode
-- on device. This mode applies to all instances of the Spanning
-- Tree protocol running on the device.
--
-- When the value of this MIB object gets changed, the path cost
-- of all ports will be reassigned to the default path cost
-- values based on the new spanning tree path cost mode and the
-- ports' speed.
--
-- When the value of this MIB object is long(2),
-- the stpxLongStpPortPathCost MIB object must be used in order
-- to retrieve/configure the spanning tree port path cost as a
-- 32 bits value. The set operation on dot1dStpPortPathCost in
-- BRIDGE-MIB will be rejected. While retrieving the value of
-- dot1dStpPortPathCost, the maximum value of 65535 will be
-- returned if the value of stpxLongStpPortPathCost for the same
-- instance exceeds 65535.
--
-- When the value of this MIB object is short(1),
-- the dot1dStpPortPathCost in BRIDGE-MIB must be used."
--
-- ::= { stpxSpanningTreeObjects 7 }
--
--
-- MISTP Objects
--
--
-- stpxMISTPInstanceNumber OBJECT-TYPE
-- SYNTAX Integer32 (1..256)
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The number of MISTP instances, that are supported by the device
-- when the value of stpxSpanningTreeType is either mistp(2)
-- or mistpPvstPlus(3)."
-- ::= { stpxMISTPObjects 1}
--
--
-- When stpxSpanningTreeType is modified from a value of 'pvstPlus' to
-- either 'mistp' or 'mistpPvstPlus', the agent will create a fixed
-- number (specified in stpxMISTPInstanceNumber) of MISTP instances in
-- this table. When stpxSpanningTreeType is changed to 'pvstPlus', the
-- agent will delete all the MISTP instances from this table and also
-- all the MIB objects associated with them.
--
-- stpxMISTPInstanceTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxMISTPInstanceEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "This table contains one entry for each instance of MISTP and
-- it contains stpxMISTPInstanceNumber entries, numbered from 1
-- to stpxMISTPInstanceNumber.
--
-- This table is only instantiated when the value of
-- stpxSpanningTreeType is mistp(2) or mistpPvstPlus(3)."
-- ::= {stpxMISTPObjects 2 }
--
-- stpxMISTPInstanceEntry OBJECT-TYPE
-- SYNTAX StpxMISTPInstanceEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A conceptual row containing the status of the MISTP
-- instance."
-- INDEX { stpxMISTPInstanceIndex }
-- ::= { stpxMISTPInstanceTable 1 }
--
-- StpxMISTPInstanceEntry ::= SEQUENCE {
-- stpxMISTPInstanceIndex Integer32,
-- stpxMISTPInstanceEnable TruthValue,
-- stpxMISTPInstanceVlansMapped OCTET STRING,
-- stpxMISTPInstanceVlansMapped2k OCTET STRING,
-- stpxMISTPInstanceVlansMapped3k OCTET STRING,
-- stpxMISTPInstanceVlansMapped4k OCTET STRING
-- }
--
-- stpxMISTPInstanceIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..256)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An arbitrary integer within the range from 1 to the value of
-- stpxMISTPInstanceNumber that uniquely identifies an instance."
-- ::= {stpxMISTPInstanceEntry 1 }
--
-- stpxMISTPInstanceEnable OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "This object indicates whether the MISTP protocol is currently
-- enabled on the MISTP instance.
--
-- If this object is set to
-- 'true' - the MISTP protocol will run on this instance.
--
-- 'false' - the MISTP protocol will stop running on this
-- instance.
-- "
-- DEFVAL { true }
-- ::= {stpxMISTPInstanceEntry 2 }
--
-- stpxMISTPInstanceVlansMapped OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 0 through 7; the second octet to VLANs 8 through
-- 15; etc. The most significant bit of each octet
-- corresponds to the lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is mapped to this MISTP instance,
-- then the bit corresponding to that VLAN is set to '1'."
-- ::= {stpxMISTPInstanceEntry 3 }
--
-- stpxMISTPInstanceVlansMapped2k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 1024 through 2047. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 1024 through 1031; the second octet to VLANs 1032
-- through 1039; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MISTP instance,
-- then the bit corresponding to that VLAN is set to '1'.
--
-- This object is only instantiated on devices with
-- support for VlanIndex up to 4095."
-- ::= {stpxMISTPInstanceEntry 4 }
--
-- stpxMISTPInstanceVlansMapped3k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 2048 through 3071. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 2048 through 2055; the second octet to VLANs 2056
-- through 2063; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MISTP instance,
-- then the bit corresponding to that VLAN is set to '1'.
--
-- This object is only instantiated on devices with
-- support for VlanIndex up to 4095."
-- ::= {stpxMISTPInstanceEntry 5 }
--
-- stpxMISTPInstanceVlansMapped4k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 3072 through 4095. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 3072 through 3079; the second octet to VLANs 3080
-- through 3087; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MISTP instance,
-- then the bit corresponding to that VLAN is set to '1'.
--
-- This object is only instantiated on devices with
-- support for VlanIndex up to 4095."
-- ::= {stpxMISTPInstanceEntry 6 }
--
--
-- stpxVlanMISTPInstMapTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxVlanMISTPInstMapEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing the MISTP Instance Index of the VLANs for a
-- particular management domain.
--
-- This table is only instantiated when the value of
-- stpxSpanningTreeType is mistp(2) or mistpPvstPlus(3)."
-- ::= { stpxMISTPObjects 3 }
--
-- stpxVlanMISTPInstMapEntry OBJECT-TYPE
-- SYNTAX StpxVlanMISTPInstMapEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A conceptual row containing the MISTP Instance Index of the
-- VLAN for a particular management domain."
-- AUGMENTS { vtpVlanEntry }
-- ::= { stpxVlanMISTPInstMapTable 1 }
--
-- StpxVlanMISTPInstMapEntry ::= SEQUENCE {
-- stpxVlanMISTPInstMapInstIndex Integer32
-- }
--
-- stpxVlanMISTPInstMapInstIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..256)
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The MISTP instance, to which the corresponding vlan is mapped.
-- If this value of this mib object is 0, the corresponding vlan
-- is not configured to be mapped to any MISTP instance and all
-- the ports under this VLAN remain in blocking state."
-- ::= { stpxVlanMISTPInstMapEntry 1}
--
-- stpxVlanMISTPInstMapEditTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxVlanMISTPInstMapEditEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing the MISTP related information for the VLANs
-- in the Edit Buffers for a particular management domain.
--
-- This table is only instantiated when when the value of
-- stpxSpanningTreeType is mistp(2) or mistpPvstPlus(3)."
-- ::= { stpxMISTPObjects 4 }
--
-- stpxVlanMISTPInstMapEditEntry OBJECT-TYPE
-- SYNTAX StpxVlanMISTPInstMapEditEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "Information about one VLAN mapping to one instance
-- in the Edit Buffer for a particular management domain."
-- AUGMENTS { vtpVlanEditEntry }
-- ::= { stpxVlanMISTPInstMapEditTable 1 }
--
-- StpxVlanMISTPInstMapEditEntry ::= SEQUENCE {
-- stpxVlanMISTPInstMapEditInstIndex Integer32
-- }
--
-- stpxVlanMISTPInstMapEditInstIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..256)
-- MAX-ACCESS read-create
-- STATUS current
-- DESCRIPTION
-- "The MISTP instance, to which the corresponding vlan would be
-- mapped. The value of this mib object is from 0 to the value of
-- stpxMISTPInstanceNumber. If setting the value of this object
-- to 0, the corresponding vlan will not be mapped to a MISTP
-- instance and all the ports under this VLAN will be moved into
-- the blocking state."
-- ::= { stpxVlanMISTPInstMapEditEntry 1 }
--
-- stpxPreferredMISTPInstancesTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxPreferredMISTPInstancesEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The table containing indications of which MISTP instances
-- are preferred on which trunk ports. The preferred
-- MISTP instances on a trunk port have a lower Path Cost value
-- compared with the MISTP instances on the trunk not in the
-- preferred list.
--
-- This table is only instantiated when the value of
-- stpxSpanningTreeType is mistp(2) or mistpPvstPlus(3)."
-- ::= { stpxMISTPObjects 5 }
--
-- stpxPreferredMISTPInstancesEntry OBJECT-TYPE
-- SYNTAX StpxPreferredMISTPInstancesEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An entry indicating which MISTP instances are preferred on
-- a specific trunk port."
-- AUGMENTS { vlanTrunkPortEntry }
-- ::= { stpxPreferredMISTPInstancesTable 1 }
--
-- StpxPreferredMISTPInstancesEntry ::=
-- SEQUENCE {
-- stpxPreferredMISTPInstancesMap OCTET STRING
-- }
--
-- stpxPreferredMISTPInstancesMap OBJECT-TYPE
-- SYNTAX OCTET STRING(SIZE(1..32))
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per MISTP instances
-- in the management domain on this trunk port. The first octet
-- corresponds to MISTP instances with InstIndex values of 1
-- through 8; the second octet to MISTP instances 9 through 16;
-- etc. The most significant bit of each octet corresponds to
-- the lowest value instanceIndex in that octet. The number of
-- bits for this mib object will be determined by the value of
-- stpxMISTPInstanceNumber.
--
-- For each instance, if it is preferred on this trunk port,
-- then the bit corresponding to that instance is set to '1'.
--
--
-- To avoid conflicts between overlapping partial updates by
-- multiple managers, i.e., updates which modify only a portion
-- of an instance of this object (e.g., enable/disable a single
-- instance on the trunk port), any SNMP Set operation
-- accessing an instance of this object should also write the
-- value of vlanTrunkPortSetSerialNo."
--
-- ::= { stpxPreferredMISTPInstancesEntry 1 }
--
--
-- STP Loop Guard Capability
--
--
-- stpxLoopGuardConfigTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxLoopGuardConfigEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports for which
-- Spanning Tree LoopGuard capability can be configured."
-- ::= { stpxLoopGuardObjects 1 }
--
-- stpxLoopGuardConfigEntry OBJECT-TYPE
-- SYNTAX StpxLoopGuardConfigEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A bridge port for which Spanning Tree LoopGuard
-- capability can be configured."
-- INDEX { stpxLoopGuardConfigPortIndex }
-- ::= { stpxLoopGuardConfigTable 1 }
--
-- StpxLoopGuardConfigEntry ::= SEQUENCE {
-- stpxLoopGuardConfigPortIndex Integer32,
-- stpxLoopGuardConfigEnabled TruthValue,
-- stpxLoopGuardConfigMode INTEGER
-- }
--
-- stpxLoopGuardConfigPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxLoopGuardConfigEntry 1 }
--
-- stpxLoopGuardConfigEnabled OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "An indication of whether the LoopGuard capability is
-- enabled on this port or not. This configuration will be
-- applied to all the Spanning Tree instances in which this
-- port exists.
--
-- In order to support additional Loop Guard config mode
-- (default) as defined in stpxLoopGuardConfigMode other
-- than enable (true(1)) or disable (false(2)) as defined
-- in this object, stpxLoopGuardConfigMode object needs to
-- be used.
--
-- When the stpxLoopGuardConfigMode object has the value of
-- enable(1), the value of stpxLoopGuardConfigEnabled for
-- the same instance will be true(1). When the
-- stpxLoopGuardConfigMode object has the value of disable(2),
-- the value of stpxLoopGuardConfigEnabled for the same
-- instance will be false(2). When the stpxLoopGuardConfigMode
-- object has the value of default(3), the value of
-- stpxLoopGuardConfigEnabled for the same instance will
-- depend on the object value of
-- stpxLoopGuardGlobalDefaultMode."
-- DEFVAL { false }
-- ::= { stpxLoopGuardConfigEntry 2 }
--
--
-- stpxLoopGuardConfigMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- enable(1),
-- disable(2),
-- default(3)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the mode of Loop Guard Feature on this
-- port. This configuration will be applied to all
-- the Spanning Tree instances in which this port
-- exists.
--
-- enable - - the Loop Guard feature is enabled on this
-- port.
--
-- disable - - the Loop Guard feature is disabled on this
-- port.
--
-- default - - whether the Loop Guard feature is enabled
-- or not on this port depends on the object
-- value of stpxLoopGuardGlobalDefaultMode."
-- ::= { stpxLoopGuardConfigEntry 3 }
--
-- stpxLoopInconsistencyTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxLoopInconsistencyEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports for which
-- a particular Spanning Tree instance has been found
-- to have a loop-inconsistency. The agent creates a new
-- entry in this table whenever it detects a new
-- loop-inconsistency, and deletes entries
-- when/soon after the inconsistency is no longer present."
-- ::= { stpxLoopGuardObjects 2 }
--
-- stpxLoopInconsistencyEntry OBJECT-TYPE
-- SYNTAX StpxLoopInconsistencyEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A Spanning Tree instance on a particular port for
-- which a Spanning Tree loop-inconsistency is currently
-- in effect."
-- INDEX { stpxLoopInconsistencyIndex,
-- stpxLoopInconsistencyPortIndex }
-- ::= { stpxLoopInconsistencyTable 1 }
--
-- StpxLoopInconsistencyEntry ::= SEQUENCE {
-- stpxLoopInconsistencyIndex Integer32,
-- stpxLoopInconsistencyPortIndex Integer32,
-- stpxLoopInconsistencyState TruthValue
-- }
--
-- stpxLoopInconsistencyIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The Spanning Tree instance id, such as the VLAN id
-- of the VLAN if the object value of stpxSpanningTreeType
-- is pvstPlus(1) or rapidPvstPlus(5)."
-- ::= { stpxLoopInconsistencyEntry 1 }
--
-- stpxLoopInconsistencyPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxLoopInconsistencyEntry 2 }
--
-- stpxLoopInconsistencyState OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates whether the port on a particular Spanning
-- Tree instance is currently in loop-inconsistent
-- state or not."
-- ::= { stpxLoopInconsistencyEntry 3 }
--
-- stpxLoopGuardGlobalDefaultMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- enable(1),
-- disable(2)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the global default config mode of LoopGuard
-- feature on the device."
-- ::= { stpxLoopGuardObjects 3 }
--
--
--
-- Spanning Tree Port Fast Start Objects
--
--
-- stpxFastStartBpduGuardEnable OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION "Indicates the global default mode of the Bpdu
-- Guard feature on the device.
--
-- On platforms that does not support per port
-- Bpdu Guard configuration as indicated by
-- the object stpxFastStartPortBpduGuardMode,
-- if the value of this object is set to true(1),
-- and the Fast Start Feature is operationally
-- enabled on a port, then that port will be
-- immediately disabled when the system receives
-- a BPDU from that port."
-- DEFVAL { false }
-- ::= { stpxFastStartObjects 1 }
--
-- stpxFastStartBpduFilterEnable OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION "Indicates the global default mode of the Bpdu
-- Filter feature on the device.
--
-- On platforms that does not support per port
-- Bpdu Filter configuration as indicated by
-- the object stpxFastStartPortBpduFilterMode,
-- if the value of this object is set to true(1),
-- and the Fast Start Feature is operationally
-- enabled on a port, then no BPDUs will be
-- transmitted on this port."
-- DEFVAL { false }
-- ::= { stpxFastStartObjects 2 }
--
-- stpxFastStartPortTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxFastStartPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports for
-- which Spanning Tree Port Fast Start can be
-- configured."
-- ::= { stpxFastStartObjects 3 }
--
-- stpxFastStartPortEntry OBJECT-TYPE
-- SYNTAX StpxFastStartPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A bridge port for which Spanning Tree Port Fast
-- Start can be configured."
-- INDEX { stpxFastStartPortIndex }
-- ::= { stpxFastStartPortTable 1 }
--
-- StpxFastStartPortEntry ::= SEQUENCE {
-- stpxFastStartPortIndex Integer32,
-- stpxFastStartPortEnable TruthValue,
-- stpxFastStartPortMode INTEGER,
-- stpxFastStartPortBpduGuardMode INTEGER,
-- stpxFastStartPortBpduFilterMode INTEGER
-- }
--
-- stpxFastStartPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxFastStartPortEntry 1 }
--
-- stpxFastStartPortEnable OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "Indicates whether the port is operating in spantree
-- fast start mode. A port with fast start enabled is
-- immediately put in spanning tree forwarding state when
-- that port is detected by the Spanning Tree, rather
-- than starting in blocking state which is the normal
-- operation.
--
-- In order to support additional Fast Start enable mode
-- (enableForTrunk and default) as defined in
-- stpxFastStartPortMode other than enable (true(1))
-- or disable (false(2)) as defined in this object,
-- stpxFastStartPortMode object needs to be used.
--
-- When the stpxFastStartPortMode has the value of
-- enable(1) or enableForTrunk(3), the value of
-- stpxFastStartPortEnable for the same instance
-- will be true(1). When the stpxFastStartPortMode
-- has the value of disable(2), the value of
-- stpxFastStartPortEnable for the same instance will be
-- false(2). When the stpxFastStartPortMode has the value
-- of default(4), the value of stpxFastStartPortEnable for
-- the same instance depends on the object value of
-- stpxFastStartGlobalDefaultMode."
-- DEFVAL { false }
-- ::= { stpxFastStartPortEntry 2 }
--
-- stpxFastStartPortMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- enable(1),
-- disable(2),
-- enableForTrunk(3),
-- default(4),
-- network(5)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the mode of Fast Start Feature on the
-- port. A port with fast start enabled is immediately
-- put in spanning tree forwarding state when the port
-- is detected by the Spanning Tree, rather than
-- starting in blocking state which is the normal
-- operation.
--
-- enable - - the fast start feature is enabled on this
-- port but will only take effect when the
-- object value of its
-- vlanTrunkPortDynamicStatus as specified
-- in CISCO-VTP-MIB is notTrunking(2).
--
-- disable - - the fast start feature is disabled on this
-- port.
--
-- enableForTrunk - - the fast start feature is enabled
-- on this port and will take effect
-- regardless of the object value of
-- its vlanTrunkPortDynamicStatus.
--
-- default - - whether the fast start feature is enabled
-- or not on this port depends on the object
-- value of stpxFastStartGlobalDefaultMode.
--
-- network - - the fast start network mode is enabled on
-- this port."
--
-- ::= { stpxFastStartPortEntry 3 }
--
-- stpxFastStartPortBpduGuardMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- enable(1),
-- disable(2),
-- default(3)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the mode of Bpdu Guard Feature on the
-- port. A port with Bpdu Guard enabled is
-- immediately disabled when the system
-- receives a BPDU from that port.
--
-- enable - - the Bpdu Guard feature is enabled on this
-- port.
--
-- disable - - the Bpdu Guard feature is disabled on this
-- port.
--
-- default - - whether the Bpdu Guard feature is enabled
-- or not on this port depends on the object
-- value of stpxFastStartBpduGuardEnable. If
-- the value of stpxFastStartBpduGuardEnable
-- is true(1) and Fast Start feature is also
-- enabled operationally on this port, then
-- this port is immediately disabled when
-- the system receives a BPDU from this port."
-- DEFVAL { default }
-- ::= { stpxFastStartPortEntry 4 }
--
-- stpxFastStartPortBpduFilterMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- enable(1),
-- disable(2),
-- default(3)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the mode of Bpdu Filter Feature on the
-- port. The system will not transmit BPDUs on a port
-- with Bpdu Filter feature enabled.
--
-- enable - - the Bpdu Filter feature is enabled on this
-- port.
--
-- disable - - the Bpdu Filter feature is disabled on this
-- port.
--
-- default - - whether the Bpdu Filter feature is enabled
-- or not on this port depends on the object
-- value of stpxFastStartBpduFilterEnable. If
-- the value of stpxFastStartBpduFilterEnable
-- is true(1) and Fast Start feature is also
-- enabled operationally on this port, then
-- no BPDUs will be transmitted on this port."
-- DEFVAL { default }
-- ::= { stpxFastStartPortEntry 5 }
--
--
-- stpxFastStartGlobalDefaultMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- enable(1),
-- disable(2)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the global default mode of the Fast
-- Start feature on the device."
-- DEFVAL { disable }
-- ::= { stpxFastStartObjects 4 }
--
-- stpxFastStartOperModeTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxFastStartOperModeEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports
-- for a particular Spanning Tree Instance."
-- ::= { stpxFastStartObjects 5 }
--
-- stpxFastStartOperModeEntry OBJECT-TYPE
-- SYNTAX StpxFastStartOperModeEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An entry with port fast start oper mode
-- information on a bridge port for a particular
-- Spanning Tree Instance."
-- INDEX { stpxFastStartOperModeInstIndex,
-- stpxFastStartOperModePortIndex }
-- ::= { stpxFastStartOperModeTable 1 }
--
-- StpxFastStartOperModeEntry ::= SEQUENCE {
-- stpxFastStartOperModeInstIndex Integer32,
-- stpxFastStartOperModePortIndex Integer32,
-- stpxFastStartOperMode INTEGER
-- }
--
-- stpxFastStartOperModeInstIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The Spanning Tree instance id, such as the VLAN id
-- of the VLAN if the object value of stpxSpanningTreeType
-- is pvstPlus(1)."
-- ::= { stpxFastStartOperModeEntry 1 }
--
-- stpxFastStartOperModePortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxFastStartOperModeEntry 2 }
--
-- stpxFastStartOperMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- enabled(1),
-- disabled(2)
-- }
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the fast start operational status of the
-- port on a particular Spanning Tree Instance."
-- ::= { stpxFastStartOperModeEntry 3 }
--
--
-- BPDU Skewing Feature
--
-- stpxBpduSkewingDetectionEnable OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates whether BPDU skewing detection feature
-- is enabled or not on the system. If this object has
-- the value of true(1), then the system will detect
-- whether BPDUs received by any port on any Spanning
-- Tree instance are processed at an interval longer
-- than the object value of dot1dStpHelloTime in the
-- BIRDGE-MIB of the Spanning Tree instance."
-- DEFVAL { false }
-- ::= { stpxBpduSkewingObjects 1 }
--
-- stpxBpduSkewingTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxBpduSkewingEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports for
-- which a particular Spanning Tree instance has been
-- detected to have BPDU skewing occurred since the
-- object value of stpxBpduSkewingDetectionEnable was
-- last changed to true(1).
--
-- The agent creates a new entry in this table whenever
-- a port in a particular Spanning Tree instance is
-- detected to be BPDU skewed since the object value of
-- stpxBpduSkewingDetectionEnable object is changed to
-- true(1). The agent deletes all the entries in this
-- table when the object value of
-- stpxBpduSkewingDetectionEnable is changed to false(2)
-- or the object value of stpxSpanningTreeType is
-- changed."
-- ::= { stpxBpduSkewingObjects 2 }
--
-- stpxBpduSkewingEntry OBJECT-TYPE
-- SYNTAX StpxBpduSkewingEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A Spanning Tree instance on a particular port for
-- which BPDU skewing has been detected."
-- INDEX { stpxBpduSkewingInstanceIndex,
-- stpxBpduSkewingPortIndex }
-- ::= { stpxBpduSkewingTable 1 }
--
-- StpxBpduSkewingEntry ::= SEQUENCE {
-- stpxBpduSkewingInstanceIndex Integer32,
-- stpxBpduSkewingPortIndex Integer32,
-- stpxBpduSkewingLastSkewDuration Unsigned32,
-- stpxBpduSkewingWorstSkewDuration Unsigned32,
-- stpxBpduSkewingWorstSkewTime TimeStamp
-- }
--
-- stpxBpduSkewingInstanceIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The Spanning Tree instance id, such as the VLAN id
-- of the VLAN if the object value of stpxSpanningTreeType
-- is pvstPlus(1)."
-- ::= { stpxBpduSkewingEntry 1 }
--
-- stpxBpduSkewingPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxBpduSkewingEntry 2 }
--
-- stpxBpduSkewingLastSkewDuration OBJECT-TYPE
-- SYNTAX Unsigned32
-- UNITS "milliseconds"
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the skew duration in milliseconds of the
-- last BPDU skewing detected."
-- ::= { stpxBpduSkewingEntry 3 }
--
-- stpxBpduSkewingWorstSkewDuration OBJECT-TYPE
-- SYNTAX Unsigned32
-- UNITS "milliseconds"
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the skew duration in milliseconds of the
-- worst BPDU skewing detected."
-- ::= { stpxBpduSkewingEntry 4 }
--
-- stpxBpduSkewingWorstSkewTime OBJECT-TYPE
-- SYNTAX TimeStamp
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the value of sysUpTime when the worst
-- BPDU skewing was detected."
-- ::= { stpxBpduSkewingEntry 5 }
--
--
-- Multiple Spanning Tree Objects
--
--
-- stpxMSTMaxInstanceNumber OBJECT-TYPE
-- SYNTAX Integer32 (1..256)
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "The maximum MST (Multiple Spanning Tree) instance id,
-- that can be supported by the device for Cisco proprietary
-- implementation of the MST Protocol.
--
-- This object is deprecated and replaced by
-- stpxSMSTMaxInstanceID."
-- ::= { stpxMSTObjects 1}
--
-- stpxMSTRegionName OBJECT-TYPE
-- SYNTAX DisplayString (SIZE(0..32))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The operational MST region name."
-- ::= { stpxMSTObjects 2}
--
-- stpxMSTRegionRevision OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "The operational MST region version.
--
-- This object is deprecated and replaced by
-- stpxSMSTRegionRevision."
-- ::= { stpxMSTObjects 3 }
--
-- stpxMSTInstanceTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxMSTInstanceEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "This table contains MST instance information with
-- one entry for an MST instance within the range of
-- 0 to the object value of stpxMSTMaxInstanceNumber.
--
-- This table is deprecated and replaced by
-- stpxSMSTInstanceTable."
-- ::= {stpxMSTObjects 4 }
--
-- stpxMSTInstanceEntry OBJECT-TYPE
-- SYNTAX StpxMSTInstanceEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "A conceptual row containing the MST instance
-- information."
-- INDEX { stpxMSTInstanceIndex }
-- ::= { stpxMSTInstanceTable 1 }
--
-- StpxMSTInstanceEntry ::= SEQUENCE {
-- stpxMSTInstanceIndex Integer32,
-- stpxMSTInstanceVlansMapped OCTET STRING,
-- stpxMSTInstanceVlansMapped2k OCTET STRING,
-- stpxMSTInstanceVlansMapped3k OCTET STRING,
-- stpxMSTInstanceVlansMapped4k OCTET STRING,
-- stpxMSTInstanceRemainingHopCount Integer32
-- }
--
-- stpxMSTInstanceIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..256)
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "An integer that uniquely identifies an MST instance
-- within the range of 0 to the object value of
-- stpxMSTMaxInstanceNumber.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceIndex."
-- ::= {stpxMSTInstanceEntry 1 }
--
-- stpxMSTInstanceVlansMapped OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 0 through 7; the second octet to VLANs 8 through
-- 15; etc. The most significant bit of each octet
-- corresponds to the lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to '1'.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceVlansMapped1k2k."
-- ::= {stpxMSTInstanceEntry 2 }
--
-- stpxMSTInstanceVlansMapped2k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 1024 through 2047. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 1024 through 1031; the second octet to VLANs 1032
-- through 1039; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to '1'.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceVlansMapped1k2k."
-- ::= {stpxMSTInstanceEntry 3 }
--
-- stpxMSTInstanceVlansMapped3k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 2048 through 3071. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 2048 through 2055; the second octet to VLANs 2056
-- through 2063; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to '1'.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceVlansMapped3k4k."
-- ::= {stpxMSTInstanceEntry 4 }
--
-- stpxMSTInstanceVlansMapped4k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 3072 through 4095. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 3072 through 3079; the second octet to VLANs 3080
-- through 3087; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to '1'.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceVlansMapped3k4k."
-- ::= {stpxMSTInstanceEntry 5 }
--
-- stpxMSTInstanceRemainingHopCount OBJECT-TYPE
-- SYNTAX Integer32 (0..40)
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "The remaining hop count for this MST instance.
--
-- This object will take on value of 40 if the object value
-- of stpxSMSTInstanceRemainingHopCount is greater than 40.
--
-- This object is only instantiated when the object value of
-- stpxSpanningTreeType is mst(4).
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceRemainingHopCount."
-- ::= {stpxMSTInstanceEntry 6 }
--
-- stpxMSTRegionEditBufferStatus OBJECT-TYPE
-- SYNTAX INTEGER {
-- released(1),
-- acquiredBySnmp(2),
-- acquiredByNonSnmp(3)
-- }
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the current ownership status of the unique
-- Region Config Edit Buffer.
--
-- released - - the Edit Buffer can be acquired by any of
-- the SNMP management stations.
--
-- acquiredBySnmp - - the Edit Buffer is acquired by
-- any of the SNMP management stations.
--
-- acquiredByNonSnmp - - the Edit Buffer is acquired by the
-- non-SNMP users managing the device."
-- ::= { stpxMSTObjects 5 }
--
-- stpxMSTRegionEditBufferOperation OBJECT-TYPE
-- SYNTAX INTEGER {
-- other(1), - - read-only
-- acquire(2),
-- releaseWithForce(3),
-- commit(4),
-- rollBack(5)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the operation that is performed on the Region
-- Config Edit Buffer.
--
-- other - - none of the following operations.
--
-- acquire - - acquire the Edit Buffer. This operation can
-- only be performed when the object
-- stpxMSTRegionEditBufferStatus has the value of
-- released(1). After the successful operation of
-- this action, the stpxMSTRegionEditBufferStatus
-- will be changed to acquiredBySnmp(2).
--
-- releaseWithForce - - release the Edit Buffer acquired by
-- non-SNMP users with force and discard the changes
-- in the Edit Buffer. This operation can only be
-- performed when the object
-- stpxMSTRegionEditBufferStatus has the value of
-- acquiredByNonSnmp(2).
--
-- commit - - commit the changes in the Edit Buffer
-- and release the Edit Buffer. The successful
-- operation of this action will make the changes
-- in the Edit Buffer effective on the device.
-- This operation can only be performed when the
-- object stpxMSTRegionEditBufferStatus has the
-- value of acquiredBySnmp(3).
--
-- rollBack - - discard the changes in the Edit Buffer
-- and release the Edit Buffer. This operation can
-- only be performed when the object
-- stpxMSTRegionEditBufferStatus has the value
-- of acquiredBySnmp(3).
--
-- This object always returns other(1) when it is read."
-- ::= { stpxMSTObjects 6 }
--
--
-- stpxMSTRegionEditName OBJECT-TYPE
-- SYNTAX DisplayString (SIZE(0..32))
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The MST region name in the Edit Buffer.
--
-- This object is only instantiated when the
-- stpxMSTRegionEditBufferStatus has the value of
-- acquiredBySnmp(2)."
-- ::= { stpxMSTObjects 7 }
--
-- stpxMSTRegionEditRevision OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "The MST region version in the Edit Buffer. This object is
-- only instantiated when the stpxMSTRegionEditBufferStatus
-- has the value of acquiredBySnmp(2).
--
-- This object is deprecated and replaced by
-- stpxSMSTRegionEditRevision."
-- ::= { stpxMSTObjects 8 }
--
-- stpxMSTInstanceEditTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxMSTInstanceEditEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "This table contains MST instance information in the
-- Edit Buffer with one entry for each MST
-- instance numbered from 0 to stpxMSTMaxInstanceNumber.
--
-- This table is only instantiated when the
-- stpxMSTRegionEditBufferStatus has the value of
-- acquiredBySnmp(2).
--
-- This table is deprecated and replaced by
-- stpxSMSTInstanceEditTable."
-- ::= { stpxMSTObjects 9 }
--
-- stpxMSTInstanceEditEntry OBJECT-TYPE
-- SYNTAX StpxMSTInstanceEditEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "A conceptual row containing MST instance information
-- in the Edit Buffer."
-- INDEX { stpxMSTInstanceEditIndex }
-- ::= { stpxMSTInstanceEditTable 1 }
--
-- StpxMSTInstanceEditEntry ::= SEQUENCE {
-- stpxMSTInstanceEditIndex Integer32,
-- stpxMSTInstanceEditVlansMap OCTET STRING,
-- stpxMSTInstanceEditVlansMap2k OCTET STRING,
-- stpxMSTInstanceEditVlansMap3k OCTET STRING,
-- stpxMSTInstanceEditVlansMap4k OCTET STRING
-- }
--
-- stpxMSTInstanceEditIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..256)
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "An integer that uniquely identifies an MST instance
-- from 0 to the object value of stpxMSTMaxInstanceNumber.
--
-- The instances of this table entry with
-- stpxMSTInstanceEditIndex of zero can not be
-- modified.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceEditIndex."
-- ::= {stpxMSTInstanceEditEntry 1 }
--
-- stpxMSTInstanceEditVlansMap OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 0 through 7; the second octet to VLANs 8 through
-- 15; etc. The most significant bit of each octet
-- corresponds to the lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to
-- '1'. Each VLAN can only be mapped to one unique MST
-- instance in the range from 1 to stpxMSTMaxInstanceNumber.
-- If the bit corresponding to a VLAN is changed from '1'
-- to '0', then that VLAN will be automatically mapped to
-- MST instance 0 by the device.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceEditVlansMap1k2k."
-- ::= {stpxMSTInstanceEditEntry 2 }
--
-- stpxMSTInstanceEditVlansMap2k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 1024 through 2047. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 1024 through 1031; the second octet to VLANs 1032
-- through 1039; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to
-- '1'. Each VLAN can only be mapped to one unique MST
-- instance in the range from 1 to stpxMSTMaxInstanceNumber.
-- If the bit corresponding to a VLAN is changed from '1'
-- to '0', then that VLAN will be automatically mapped to
-- MST instance 0 by the device.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceEditVlansMap1k2k."
-- ::= {stpxMSTInstanceEditEntry 3 }
--
-- stpxMSTInstanceEditVlansMap3k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 2048 through 3071. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 2048 through 2055; the second octet to VLANs 2056
-- through 2063; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to
-- '1'. Each VLAN can only be mapped to one unique MST
-- instance in the range from 1 to stpxMSTMaxInstanceNumber.
-- If the bit corresponding to a VLAN is changed from '1'
-- to '0', then that VLAN will be automatically mapped to
-- MST instance 0 by the device.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceEditVlansMap3k4k."
-- ::= {stpxMSTInstanceEditEntry 4 }
--
-- stpxMSTInstanceEditVlansMap4k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..128))
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 3072 through 4095. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 3072 through 3079; the second octet to VLANs 3080
-- through 3087; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to
-- '1'. Each VLAN can only be mapped to one unique MST
-- instance in the range from 1 to stpxMSTMaxInstanceNumber.
-- If the bit corresponding to a VLAN is changed from '1'
-- to '0', then that VLAN will be automatically mapped to
-- MST instance 0 by the device.
--
-- This object is deprecated and replaced by
-- stpxSMSTInstanceEditVlansMap3k4k."
-- ::= {stpxMSTInstanceEditEntry 5 }
--
--
-- stpxPreferredMSTInstancesTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxPreferredMSTInstancesEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "The table containing indications of which MST instances
-- are preferred on which trunk ports. The preferred
-- MST instances on a trunk port have a lower Path Cost value
-- compared with the MST instances on the trunk not in the
-- preferred list."
-- ::= { stpxMSTObjects 10 }
--
-- stpxPreferredMSTInstancesEntry OBJECT-TYPE
-- SYNTAX StpxPreferredMSTInstancesEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "An entry indicating which MST instances are preferred on
-- a specific trunk port."
-- AUGMENTS { vlanTrunkPortEntry }
-- ::= { stpxPreferredMSTInstancesTable 1 }
--
-- StpxPreferredMSTInstancesEntry ::= SEQUENCE {
-- stpxPreferredMSTInstancesMap OCTET STRING
-- }
--
-- stpxPreferredMSTInstancesMap OBJECT-TYPE
-- SYNTAX OCTET STRING(SIZE(1..32))
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "A string of octets containing one bit per MST instances
-- on this trunk port. The first octet corresponds to MST
-- instances of 0 through 7; the second octet to MST instances
-- 8 through 15; etc. The most significant bit of each octet
-- corresponds to the lowest MST instance value in that octet.
-- The number of bits for this mib object will be determined
-- by the value of stpxMSTMaxInstanceNumber.
--
-- For each instance, if it is preferred on this trunk port,
-- then the bit corresponding to that instance is set to '1'."
-- ::= { stpxPreferredMSTInstancesEntry 1 }
--
-- stpxMSTPortTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxMSTPortEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "A table containing port information for the MST
-- Protocol on all the bridge ports existing on the
-- system."
--
-- ::= { stpxMSTObjects 11 }
--
-- stpxMSTPortEntry OBJECT-TYPE
-- SYNTAX StpxMSTPortEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "An entry with port information for the MST Protocol
-- on a bridge port."
-- INDEX { stpxMSTPortIndex }
-- ::= { stpxMSTPortTable 1 }
--
-- StpxMSTPortEntry ::= SEQUENCE {
-- stpxMSTPortIndex Integer32,
-- stpxMSTPortAdminLinkType INTEGER,
-- stpxMSTPortOperLinkType INTEGER,
-- stpxMSTPortProtocolMigration TruthValue,
-- stpxMSTPortStatus BITS
-- }
--
-- stpxMSTPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxMSTPortEntry 1 }
--
-- stpxMSTPortAdminLinkType OBJECT-TYPE
-- SYNTAX INTEGER {
-- pointToPoint(1),
-- shared(2),
-- auto(3)
-- }
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "Indicates the administrative link type configuration of
-- a bridge port for the MST protocol.
--
-- pointToPoint - - the port is administratively configured to
-- be connected to a point-to-point link.
--
-- shared - - the port is administratively configured to be
-- connected to a shared medium.
--
-- auto - - the administrative configuration of the port's
-- link type depends on link duplex of the port.
-- If the port link is full-duplex, the administrative
-- link type configuration on this port will be taken
-- as pointTopoint(1). If the port link is half-duplex,
-- the administrative link type configuration on this
-- port will be taken as shared(2).
--
-- This configuration of this object only takes effect when the
-- stpxSpanningTreeType is mst(4) or rapidPvstPlus(5).
-- stpxMSTPortAdminLinkType is deprecated and replaced
-- with stpxRSTPPortAdminLinkType."
-- DEFVAL { auto }
-- ::= { stpxMSTPortEntry 2 }
--
-- stpxMSTPortOperLinkType OBJECT-TYPE
-- SYNTAX INTEGER {
-- pointToPoint(1),
-- shared(2),
-- other(3)
-- }
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "Indicates the operational link type of a bridge port
-- for the MST protocol.
--
-- pointToPoint - - the port is operationally connected to
-- a point-to-point link.
--
-- shared - - the port is operationally connected to
-- a shared medium.
--
-- other - - none of the above.
--
-- This object is only instantiated when the object value of
-- stpxSpanningTreeType is mst(4). stpxMSTPortOperLinkType
-- is deprecated and replaced with stpxRSTPPortOperLinkType."
-- ::= { stpxMSTPortEntry 3 }
--
-- stpxMSTPortProtocolMigration OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "The protocol migration control on this port. When the
-- object value of stpxSpanningTreeType is mst(4) or
-- rapidPvstPlus(5), setting true(1) to this object forces
-- the device to try using version 2 BPDUs on this port.
-- When the object value of stpxSpanningTreeType is neither
-- mst(4) nor rapidPvstPlus(5), setting true(1) to this
-- object has no effect. Setting false(2) to this object has
-- no effect. This object always returns false(2) when read.
-- stpxMSTPortProtocolMigration is deprecated and
-- replaced with stpxRSTPPortProtocolMigration."
-- REFERENCE
-- "IEEE 802.1w clause 14.8.2.4, 17.26."
-- ::= { stpxMSTPortEntry 4 }
--
-- stpxMSTPortStatus OBJECT-TYPE
-- SYNTAX BITS {
-- edge(0),
-- boundary(1),
-- pvst(2),
-- stp(3)
-- }
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "Indicates the operational status of the port for the
-- MST protocol.
--
-- edge - - this port is an edge port for the MST region.
--
-- boundary - - this port is a boundary port for the
-- MST region.
--
-- pvst - - this port is connected to a PVST/PVST+ bridge.
--
-- stp - - this port is connected to a Single Spanning
-- Tree bridge.
--
-- This object is only instantiated when the object value
-- of stpxSpanningTreeType is mst(4).
--
-- This object is deprecated and replaced by
-- stpxSMSTPortStatus."
-- ::= { stpxMSTPortEntry 5 }
--
-- stpxMSTPortRoleTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxMSTPortRoleEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "A table containing a list of the bridge ports for a
-- particular MST instance. This table is only instantiated
-- when the stpxSpanningTreeType is mst(4).
--
-- This table is deprecated and replaced with
-- stpxRSTPPortRoleTable."
-- ::= { stpxMSTObjects 12 }
--
-- stpxMSTPortRoleEntry OBJECT-TYPE
-- SYNTAX StpxMSTPortRoleEntry
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "An entry containing the port role information for the MST
-- protocol on a port for a particular MST instance existing
-- on the system."
-- INDEX { stpxMSTPortRoleInstanceIndex,
-- stpxMSTPortRolePortIndex }
-- ::= { stpxMSTPortRoleTable 1 }
--
-- StpxMSTPortRoleEntry ::= SEQUENCE {
-- stpxMSTPortRoleInstanceIndex Integer32,
-- stpxMSTPortRolePortIndex Integer32,
-- stpxMSTPortRoleValue INTEGER
-- }
--
-- stpxMSTPortRoleInstanceIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..256)
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "The MST instance id within the range of 0 to
-- stpxMSTMaxInstanceNumber."
-- ::= { stpxMSTPortRoleEntry 1 }
--
-- stpxMSTPortRolePortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS deprecated
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxMSTPortRoleEntry 2 }
--
-- stpxMSTPortRoleValue OBJECT-TYPE
-- SYNTAX INTEGER {
-- disabled(1),
-- root(2),
-- designated(3),
-- alternate(4),
-- backUp(5),
-- boundary(6),
-- master(7)
-- }
-- MAX-ACCESS read-only
-- STATUS deprecated
-- DESCRIPTION
-- "Indicates the port role on a particular MST instance
-- for the MST protocol.
--
-- disabled - - this port has no role on this MST instance.
--
-- root - - this port has the role of root port on this MST
-- instance.
--
-- designated - - this port has the role of designated
-- port on this MST instance.
--
-- alternate - - this port has the role of alternate port
-- on this MST instance.
--
-- backUp - - this port has the role of backup port on this
-- MST instance.
--
-- boundary - - this port has the role of boundary port on
-- this MST instance.
--
-- master - - this port has the role of master port on
-- this MST instance."
-- ::= { stpxMSTPortRoleEntry 3 }
--
-- stpxMSTMaxHopCount OBJECT-TYPE
-- SYNTAX Integer32 (1..40)
-- MAX-ACCESS read-write
-- STATUS deprecated
-- DESCRIPTION
-- "The maximum number of hops for the MST region.
--
-- This object will take on value of 40 if the object value
-- of stpxSMSTMaxHopCount is greater than 40.
--
-- This object is deprecated and replaced by
-- stpxSMSTMaxHopCount."
-- DEFVAL { 20 }
-- ::= { stpxMSTObjects 13 }
--
--
-- Rapid Spanning Tree Protocol Objects
--
--
-- stpxRSTPPortTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxRSTPPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing port information for the RSTP
-- Protocol on all the bridge ports existing in the
-- system."
-- ::= { stpxRSTPObjects 1 }
--
-- stpxRSTPPortEntry OBJECT-TYPE
-- SYNTAX StpxRSTPPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An entry with port information for the RSTP Protocol
-- on a bridge port."
-- INDEX { stpxRSTPPortIndex }
-- ::= { stpxRSTPPortTable 1 }
--
-- StpxRSTPPortEntry ::= SEQUENCE {
-- stpxRSTPPortIndex Integer32,
-- stpxRSTPPortAdminLinkType INTEGER,
-- stpxRSTPPortOperLinkType INTEGER,
-- stpxRSTPPortProtocolMigration TruthValue
-- }
--
-- stpxRSTPPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxRSTPPortEntry 1 }
--
-- stpxRSTPPortAdminLinkType OBJECT-TYPE
-- SYNTAX INTEGER {
-- pointToPoint(1),
-- shared(2),
-- auto(3)
-- } --
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "Indicates the administrative link type configuration of
-- a bridge port for the RSTP protocol.
--
-- pointToPoint - - the port is administratively configured to
-- be connected to a point-to-point link.
--
-- shared - - the port is administratively configured to be
-- connected to a shared medium.
--
-- auto - - the administrative configuration of the port's
-- link type depends on link duplex of the port.
-- If the port link is full-duplex, the administrative
-- link type configuration on this port will be taken
-- as pointTopoint(1). If the port link is half-duplex,
-- the administrative link type configuration on this
-- port will be taken as shared(2).
--
-- This configuration of this object only takes effect when the
-- stpxSpanningTreeType is mst(4) or rapidPvstPlus(5)."
-- DEFVAL { auto }
-- ::= { stpxRSTPPortEntry 2 }
--
-- stpxRSTPPortOperLinkType OBJECT-TYPE
-- SYNTAX INTEGER {
-- pointToPoint(1),
-- shared(2),
-- other(3)
-- } --
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the operational link type of a bridge port
-- for the RSTP protocol.
--
-- pointToPoint - - the port is operationally connected to
-- a point-to-point link.
--
-- shared - - the port is operationally connected to
-- a shared medium.
--
-- other - - none of the above.
--
-- This object is only instantiated when the object value of
-- stpxSpanningTreeType is mst(4) or rapidPvstPlus(5)."
-- ::= { stpxRSTPPortEntry 3 }
--
-- stpxRSTPPortProtocolMigration OBJECT-TYPE
-- SYNTAX TruthValue
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The protocol migration control on this port. When the
-- object value of stpxSpanningTreeType is mst(4) or
-- rapidPvstPlus(5), setting true(1) to this object forces
-- the device to try using version 2 BPDUs on this port.
-- When the object value of stpxSpanningTreeType is neither
-- mst(4) nor rapidPvstPlus(5), setting true(1) to
-- this object has no effect. Setting false(2) to this
-- object has no effect. This object always returns
-- false(2) when read."
-- REFERENCE
-- "IEEE 802.1w clause 14.8.2.4, 17.26."
-- ::= { stpxRSTPPortEntry 4 }
--
--
-- stpxRSTPPortRoleTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxRSTPPortRoleEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports for a
-- particular Spanning Tree instance. This table is
-- only instantiated when the stpxSpanningTreeType is mst(4)
-- or rapidPvstPlus(5)."
-- ::= { stpxRSTPObjects 2 }
--
-- stpxRSTPPortRoleEntry OBJECT-TYPE
-- SYNTAX StpxRSTPPortRoleEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An entry containing the port role information for the RSTP
-- protocol on a port for a particular Spanning Tree instance."
-- INDEX { stpxRSTPPortRoleInstanceIndex,
-- stpxRSTPPortRolePortIndex }
-- ::= { stpxRSTPPortRoleTable 1 }
--
-- StpxRSTPPortRoleEntry ::= SEQUENCE {
-- stpxRSTPPortRoleInstanceIndex Integer32,
-- stpxRSTPPortRolePortIndex Integer32,
-- stpxRSTPPortRoleValue INTEGER
-- }
--
-- stpxRSTPPortRoleInstanceIndex OBJECT-TYPE
-- SYNTAX Integer32 (0..4095)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The Spanning Tree instance id, it can either be a
-- VLAN number if the stpxSpanningTreeType is rapidPvstPlus(5)
-- or an MST instance id if the stpxSpanningTreeType is mst(4)."
-- ::= { stpxRSTPPortRoleEntry 1 }
--
-- stpxRSTPPortRolePortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxRSTPPortRoleEntry 2 }
--
-- stpxRSTPPortRoleValue OBJECT-TYPE
-- SYNTAX INTEGER {
-- disabled(1),
-- root(2),
-- designated(3),
-- alternate(4),
-- backUp(5),
-- boundary(6),
-- master(7)
-- } --
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the port role on a particular Spanning Tree
-- instance for the RSTP protocol.
--
-- disabled - - this port has no role in this Spanning
-- Tree instance.
--
-- root - - this port has the role of root port in this
-- Spanning Tree instance.
--
-- designated - - this port has the role of designated
-- port in this Spanning Tree instance.
--
-- alternate - - this port has the role of alternate port
-- in this Spanning Tree instance.
--
-- backUp - - this port has the role of backup port in this
-- Spanning Tree instance.
--
-- boundary - - this port has the role of boundary port in
-- this Spanning Tree instance.
--
-- master - - this port has the role of master port in
-- this Spanning Tree instance.
--
-- This object could have a value of 'boundary' or 'master'
-- only when the object value of stpxSpanningTreeType is mst(4)."
-- ::= { stpxRSTPPortRoleEntry 3 }
--
-- stpxRSTPTransmitHoldCount OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The Transmit Hold Count."
-- ::= { stpxRSTPObjects 3 }
--
--
-- Rapid PVST+ Objects
--
-- stpxRPVSTPortTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxRPVSTPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing a list of the bridge ports
-- for a particular Spanning Tree Instance.
-- This table is only instantiated when the object value
-- of stpxSpanningTreeType is rapidPvstPlus(5)."
-- ::= { stpxRPVSTObjects 1 }
--
-- stpxRPVSTPortEntry OBJECT-TYPE
-- SYNTAX StpxRPVSTPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An entry with port status information on a
-- bridge port for a particular Spanning Tree
-- Instance."
-- INDEX { stpxRPVSTPortVlanIndex,
-- stpxRPVSTPortIndex }
-- ::= { stpxRPVSTPortTable 1 }
--
-- StpxRPVSTPortEntry ::= SEQUENCE {
-- stpxRPVSTPortVlanIndex VlanIndex,
-- stpxRPVSTPortIndex Integer32,
-- stpxRPVSTPortStatus BITS
-- }
-- stpxRPVSTPortVlanIndex OBJECT-TYPE
-- SYNTAX VlanIndex
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The VLAN id of the VLAN."
-- ::= { stpxRPVSTPortEntry 1 }
--
-- stpxRPVSTPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxRPVSTPortEntry 2 }
--
-- stpxRPVSTPortStatus OBJECT-TYPE
-- SYNTAX BITS {
-- edge(0),
-- unused1(1),
-- unused2(2),
-- stp(3),
-- dispute(4)
-- }
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the operational status of the port for the
-- Rapid PVST+ protocol.
--
-- edge - - this port is an edge port for the RST region.
--
-- unused1 - - unused bit 1.
--
-- unused2 - - unused bit 2.
--
-- stp - - this port is connected to a Single Spanning
-- Tree/PVST+ bridge.
--
-- dispute - - this port, as a designated port, received an
-- inferior BPDU with a designated role and the
-- learning bit being set."
--
-- ::= { stpxRPVSTPortEntry 3 }
--
--
-- Standard Multiple Spanning Tree Objects.
-- This group of objects is for the management
-- of IEEE Multiple Spanning Tree, i.e., Standard MST
-- (SMST). Objects in this group replace some of the
-- objects in stpxMSTObjects which are for the the
-- managment of the Cisco proprietary implementation
-- of the Multiple Spanning Tree (MST).
--
--
-- stpxSMSTMaxInstances OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The maximum number of MST instances that can be
-- supported by the device for IEEE MST."
-- ::= { stpxSMSTObjects 1 }
--
-- stpxSMSTMaxInstanceID OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The maximum MST instance ID that can be supported
-- by the device for IEEE MST."
-- ::= { stpxSMSTObjects 2 }
--
-- stpxSMSTRegionRevision OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The operational region version for IEEE MST."
-- ::= { stpxSMSTObjects 3 }
--
-- stpxSMSTRegionEditRevision OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The MST region version in the Edit Buffer for IEEE
-- MST.
--
-- This object is only instantiated when the
-- stpxMSTRegionEditBufferStatus has the value of
-- acquiredBySnmp(2)."
-- ::= { stpxSMSTObjects 4 }
--
-- stpxSMSTInstanceTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxSMSTInstanceEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "This table contains MST instance information
-- for IEEE MST."
-- ::= {stpxSMSTObjects 5 }
--
-- stpxSMSTInstanceEntry OBJECT-TYPE
-- SYNTAX StpxSMSTInstanceEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A conceptual row containing the MST instance
-- information for IEEE MST."
-- INDEX { stpxSMSTInstanceIndex }
-- ::= { stpxSMSTInstanceTable 1 }
--
-- StpxSMSTInstanceEntry ::= SEQUENCE {
-- stpxSMSTInstanceIndex Unsigned32,
-- stpxSMSTInstanceVlansMapped1k2k OCTET STRING,
-- stpxSMSTInstanceVlansMapped3k4k OCTET STRING,
-- stpxSMSTInstanceRemainingHopCount Integer32,
-- stpxSMSTInstanceCISTRegionalRoot OCTET STRING,
-- stpxSMSTInstanceCISTIntRootCost Unsigned32
-- } --
--
-- stpxSMSTInstanceIndex OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The MST instance ID, the value of which is in the range
-- from 0 to stpxSMSTMaxInstanceID."
-- ::= {stpxSMSTInstanceEntry 1 }
--
-- stpxSMSTInstanceVlansMapped1k2k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..256))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 0 through 2047. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 0 through 7; the second octet to VLANs 8 through
-- 15; etc. The most significant bit of each octet
-- corresponds to the lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to '1'.
-- If the length of this string is less than 256 octets,
-- any 'missing' octets are assumed to contain the value
-- of zero."
-- ::= {stpxSMSTInstanceEntry 2 }
--
-- stpxSMSTInstanceVlansMapped3k4k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..256))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 2048 through 4095. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 2048 through 2055; the second octet to VLANs 2056
-- through 2063; etc. The most significant bit of each
-- octet corresponds to the lowest value VlanIndex in that
-- octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to '1'.
-- If the length of this string is less than 256 octets,
-- any 'missing' octets are assumed to contain the value
-- of zero."
-- ::= {stpxSMSTInstanceEntry 3 }
--
-- stpxSMSTInstanceRemainingHopCount OBJECT-TYPE
-- SYNTAX Integer32 (-1..2147483647)
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The remaining hop count for this MST instance. If this object
-- value is not applicable on an MST instance, then the value
-- retrieved for this object for that MST instance will be -1.
--
-- This object is only instantiated when the object value of
-- stpxSpanningTreeType is mst(4)."
-- ::= {stpxSMSTInstanceEntry 4 }
--
-- stpxSMSTInstanceCISTRegionalRoot OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (8))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the Bridge Identifier (refer to BridgeId
-- defined in BRIDGE-MIB) of CIST (Common and Internal
-- Spanning Tree) Regional Root for the MST region.
--
-- This object is only instantiated when the object value of
-- stpxSpanningTreeType is mst(4) and stpxSMSTInstanceIndex
-- is 0."
-- REFERENCE
-- "IEEE 802.1S-2002: Section 13.9."
-- ::= { stpxSMSTInstanceEntry 5 }
--
-- stpxSMSTInstanceCISTIntRootCost OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the CIST Internal Root Path Cost, i.e., the
-- path cost to the CIST Regional Root as specified by the
-- corresponding stpxSMSTInstanceCISTRegionalRoot for the
-- MST region.
--
-- This object is only instantiated when the object value of
-- stpxSpanningTreeType is mst(4) and stpxSMSTInstanceIndex
-- is 0."
-- REFERENCE
-- "IEEE 802.1S-2002: Section 13.9."
-- ::= { stpxSMSTInstanceEntry 6 }
--
-- stpxSMSTInstanceEditTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxSMSTInstanceEditEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "This table contains MST instance information in the
-- Edit Buffer.
--
-- This table is only instantiated when the object value
-- of stpxMSTRegionEditBufferStatus has the value of
-- acquiredBySnmp(2)."
-- ::= { stpxSMSTObjects 6 }
--
-- stpxSMSTInstanceEditEntry OBJECT-TYPE
-- SYNTAX StpxSMSTInstanceEditEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A conceptual row containing MST instance information
-- in the Edit Buffer.
--
-- The total number of entries in this table has to be
-- less than or equal to the object value of stpxSMSTMaxInstances."
-- INDEX { stpxSMSTInstanceEditIndex }
-- ::= { stpxSMSTInstanceEditTable 1 }
--
-- StpxSMSTInstanceEditEntry ::= SEQUENCE {
-- stpxSMSTInstanceEditIndex Unsigned32,
-- stpxSMSTInstanceEditVlansMap1k2k OCTET STRING,
-- stpxSMSTInstanceEditVlansMap3k4k OCTET STRING,
-- stpxSMSTInstanceEditRowStatus RowStatus
-- } --
--
-- stpxSMSTInstanceEditIndex OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The MST instance ID, the value of which is in the range from
-- 0 to stpxSMSTMaxInstanceID.
--
-- The instances of this table entry with
-- stpxSMSTInstanceEditIndex of zero is automatically
-- created by the device and can not modified."
-- ::= {stpxSMSTInstanceEditEntry 1 }
--
-- stpxSMSTInstanceEditVlansMap1k2k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..256))
-- MAX-ACCESS read-create
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 0 through 2047. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 0 through 7; the second octet to VLANs 8 through
-- 15; etc. The most significant bit of each octet
-- corresponds to the lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to
-- '1'. Each VLAN can only be mapped to one unique MST
-- instance with the range from 0 to stpxSMSTMaxInstanceNumber.
-- If the bit corresponding to a VLAN is changed from '1'
-- to '0', then that VLAN will be automatically mapped to
-- SMST instance 0 by the device. If the bit corresponding
-- to a VLAN is changed from '0' to '1', then that VLAN will
-- be automatically removed from the MST instance this VLAN was
-- previously mapped to. If the length of this string is
-- less than 256 octets, any 'missing' octets are assumed to
-- contain the value of zero."
-- ::= {stpxSMSTInstanceEditEntry 2 }
--
-- stpxSMSTInstanceEditVlansMap3k4k OBJECT-TYPE
-- SYNTAX OCTET STRING (SIZE (0..256))
-- MAX-ACCESS read-create
-- STATUS current
-- DESCRIPTION
-- "A string of octets containing one bit per VLAN for
-- VLANS with VlanIndex values of 2048 through 4095. The
-- first octet corresponds to VLANs with VlanIndex values
-- of 2048 through 2055; the second octet to VLANs 2056 through
-- 2063; etc. The most significant bit of each octet
-- corresponds to the lowest value VlanIndex in that octet.
--
-- For each VLAN, if it is mapped to this MST instance,
-- then the bit corresponding to that VLAN is set to
-- '1'. Each VLAN can only be mapped to one unique MST
-- instance with the range from 0 to stpxSMSTMaxInstanceNumber.
-- If the bit corresponding to a VLAN is changed from '1'
-- to '0', then that VLAN will be automatically mapped to
-- SMST instance 0 by the device. If the bit corresponding
-- to a VLAN is changed from '0' to '1', then that VLAN will
-- be automatically removed from the MST instance this VLAN was
-- previously mapped to. If the length of this string is
-- less than 256 octets, any 'missing' octets are assumed to
-- contain the value of zero."
-- ::= {stpxSMSTInstanceEditEntry 3 }
--
-- stpxSMSTInstanceEditRowStatus OBJECT-TYPE
-- SYNTAX RowStatus
-- MAX-ACCESS read-create
-- STATUS current
-- DESCRIPTION
-- "This object controls the creation and deletion of a row
-- in stpxSMSTInstanceEditTable.
--
-- When creating an entry in this table, 'createAndGo' method
-- is used and the value of this object is set to 'active'.
-- Deactivation of an 'active' entry is not allowed. When
-- deleting an entry in this table, 'destroy' method is used.
-- Once a row becomes active, value in any other column
-- within such a row may be modified. When a row is active,
-- setting the instance of stpxSMSTInstanceEditVlansMap1k2k
-- stpxSMSTInstanceEditVlansMap3k4k for the same MST instance
-- both to the value of zero length can not be allowed."
-- ::= {stpxSMSTInstanceEditEntry 4 }
--
-- stpxSMSTPortTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF StpxSMSTPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "A table containing port information for the MST
-- Protocol on all the bridge ports existing on the
-- system.
--
-- This table is only instantiated when the object
-- value of stpxSpanningTreeType is mst(4)"
-- ::= { stpxSMSTObjects 7 }
--
-- stpxSMSTPortEntry OBJECT-TYPE
-- SYNTAX StpxSMSTPortEntry
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "An entry with port information for the MST protocol
-- on a bridge port."
-- INDEX { stpxSMSTPortIndex }
-- ::= { stpxSMSTPortTable 1 }
--
-- StpxSMSTPortEntry ::= SEQUENCE {
-- stpxSMSTPortIndex Integer32,
-- stpxSMSTPortStatus BITS,
-- stpxSMSTPortAdminHelloTime Unsigned32,
-- stpxSMSTPortConfigedHelloTime Unsigned32,
-- stpxSMSTPortOperHelloTime Integer32,
-- stpxSMSTPortAdminMSTMode INTEGER,
-- stpxSMSTPortOperMSTMode INTEGER
-- }
--
-- stpxSMSTPortIndex OBJECT-TYPE
-- SYNTAX Integer32 (1..65535)
-- MAX-ACCESS not-accessible
-- STATUS current
-- DESCRIPTION
-- "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
-- for the bridge port."
-- REFERENCE
-- "dot1dBasePort is defined in RFC1493."
-- ::= { stpxSMSTPortEntry 1 }
--
-- stpxSMSTPortStatus OBJECT-TYPE
-- SYNTAX BITS {
-- edge(0),
-- boundary(1),
-- pvst(2),
-- stp(3),
-- dispute(4),
-- rstp(5)
-- }
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the operational status of the port for the
-- MST protocol.
--
-- edge - - this port is an edge port for the MST region.
--
-- boundary - - this port is a boundary port for the
-- MST region.
--
-- pvst - - this port is connected to a PVST/PVST+ bridge.
--
-- stp - - this port is connected to a Single Spanning
-- Tree bridge.
--
-- dispute - - this port, as a designated port, received an
-- inferior BPDU with a designated role and the
-- learning bit being set.
--
-- rstp - - this port is connected to a RSTP bridge or an
-- MST bridge in a different MST region."
-- ::= { stpxSMSTPortEntry 2 }
--
-- stpxSMSTPortAdminHelloTime OBJECT-TYPE
-- SYNTAX Unsigned32
-- UNITS "hundredth of seconds"
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The adminitratively configured hello time in hundredth
-- of seconds on a port for IEEE MST. The granularity
-- of this timer is 1 second. An agent may return a badValue
-- error if a set is attempted to a value which is not a
-- whole number of seconds. This object value of zero
-- means the hello time is not specifically configured on
-- this port and object value of stpxSMSTPortConfigedHelloTime
-- retrieved for this port will take on the value of
-- dot1dStpBridgeHelloTime defined in BRIDGE-MIB."
-- ::= { stpxSMSTPortEntry 3 }
--
-- stpxSMSTPortConfigedHelloTime OBJECT-TYPE
-- SYNTAX Unsigned32
-- UNITS "hundredth of seconds"
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the effective configuration of the hello time on
-- a port."
-- ::= { stpxSMSTPortEntry 4 }
--
-- stpxSMSTPortOperHelloTime OBJECT-TYPE
-- SYNTAX Integer32 (-1..2147483647)
-- UNITS "hundredth of seconds"
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The operational hello time in hundredth of seconds on a
-- port for IEEE MST. If this object value is not
-- applicable on a port, then the value retrieved on that
-- port will be -1."
-- ::= { stpxSMSTPortEntry 5 }
--
-- stpxSMSTPortAdminMSTMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- preStandard(1),
-- auto(2)
-- }
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The desired MST mode of this port.
--
-- preStandard - - this port is administratively configured to
-- transmit pre-standard, i.e. pre IEEE MST, BPDUs.
--
-- auto - - the BPDU transmission mode of this port is based
-- on automatic detection of neighbor ports."
-- ::= { stpxSMSTPortEntry 6 }
--
-- stpxSMSTPortOperMSTMode OBJECT-TYPE
-- SYNTAX INTEGER {
-- unknown(1),
-- preStandard(2),
-- standard(3)
-- }
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "Indicates the current operational MST mode of this port.
--
-- unknown - - the operational mode is currently unknown.
--
-- preStandard - - this port is currently operating in
-- pre-standard MSTP BPDU transmission mode.
--
-- standard - - this port is currently operating in IEEE MST
-- BPDU transmission mode."
-- ::= { stpxSMSTPortEntry 7 }
--
-- stpxSMSTMaxHopCount OBJECT-TYPE
-- SYNTAX Unsigned32
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "The maximum number of hops for the IEEE MST region."
-- ::= { stpxSMSTObjects 8 }
--
-- stpxSMSTConfigDigest OBJECT-TYPE
-- SYNTAX StpxMSTConfigurationDigest
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The IEEE MST region configuration digest."
-- REFERENCE
-- "IEEE 802.1Q-2003 Section 13.7."
-- ::= { stpxSMSTObjects 9 }
--
-- stpxSMSTConfigPreStandardDigest OBJECT-TYPE
-- SYNTAX StpxMSTConfigurationDigest
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The pre-standard MST region configuration digest."
-- ::= { stpxSMSTObjects 10 }
--
--
-- Notifications
--
--
-- stpxNotificationsPrefix OBJECT IDENTIFIER ::= { stpxNotifications 0 }
--
-- stpxInconsistencyUpdate NOTIFICATION-TYPE
-- OBJECTS { stpxInconsistentState }
-- STATUS current
-- DESCRIPTION
-- "A stpxPortInconsistencyUpdate notification is sent by a
-- bridge when an instance of stpxInconsistentState is
-- created or destroyed. That is, when an inconsistency is
-- discovered in the VLAN's Spanning Tree for a particular
-- port, or when such an inconsistency disappears. Note
-- that the trap is not sent if the port transitions between
-- different types of inconsistency.
--
-- The stpxInconsistentState value indicates the type of
-- inconsistency which now exists/no longer exists for the
-- relevant VLAN on the relevant port."
-- ::= { stpxNotificationsPrefix 1}
--
-- stpxRootInconsistencyUpdate NOTIFICATION-TYPE
-- OBJECTS { stpxRootInconsistencyState, stpxSpanningTreeType }
-- STATUS current
-- DESCRIPTION
-- "A stpxRootInconsistencyUpdate notification is sent by a
-- bridge when an instance of stpxRootInconsistencyState
-- is created or destroyed. That is, when an
-- root-inconsistency is discovered in the VLAN's or
-- instance's Spanning Tree for a particular port, or when
-- such an root-inconsistency disappears. For creation, the
-- value of stpxRootInconsistencyState in the notification is
-- true(1); for deletion, the value is false(2).
--
-- The object value of stpxSpanningTreeType indicates
-- which Spanning Tree protocol is running when an instance
-- of stpxRootInconsistencyState is created or destroyed. "
-- ::= { stpxNotificationsPrefix 2}
--
-- stpxLoopInconsistencyUpdate NOTIFICATION-TYPE
-- OBJECTS { stpxLoopInconsistencyState, stpxSpanningTreeType }
-- STATUS current
-- DESCRIPTION
-- "A stpxLoopInconsistencyUpdate notification is sent by a
-- bridge when an instance of stpxLoopInconsistencyState
-- is created or destroyed. That is, when an
-- loop-inconsistency is discovered in the VLAN's or
-- instance's Spanning Tree for a particular port, or when
-- such an loop-inconsistency disappears. For creation,
-- the value of stpxLoopInconsistencyState in the
-- notification is true(1); for deletion, the value is
-- false(2).
--
-- The object value of stpxSpanningTreeType indicates
-- which Spanning Tree protocol is running when an instance
-- of stpxLoopInconsistencyState is created or
-- destroyed."
-- ::= { stpxNotificationsPrefix 3}
--
--
--
-- conformance information
--
-- stpxMIBConformance
-- OBJECT IDENTIFIER ::= { ciscoStpExtensionsMIB 3 }
-- stpxMIBCompliances
-- OBJECT IDENTIFIER ::= { stpxMIBConformance 1 }
-- stpxMIBGroups
-- OBJECT IDENTIFIER ::= { stpxMIBConformance 2 }
--
--
-- compliance statements
--
-- stpxMIBCompliance MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- ::= { stpxMIBCompliances 1 }
--
-- stpxMIBCompliance2 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
--
-- ::= { stpxMIBCompliances 2 }
--
-- stpxMIBCompliance3 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- ::= { stpxMIBCompliances 3 }
--
-- stpxMIBCompliance4 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
-- ::= { stpxMIBCompliances 4 }
--
-- stpxMIBCompliance5 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxFastStartGroup
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- ::= { stpxMIBCompliances 5 }
--
--
-- stpxMIBCompliance6 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxSstpGroup
-- DESCRIPTION "This group is optional for implementations of
-- Cisco's Shared Spanning Tree Protocol (SSTP)."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxBpduSkewingGroup
-- DESCRIPTION "This is an optional group for implementations of
-- Spanning Tree BPDU Skewing feature."
--
-- GROUP stpxFastStartGroup2
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- GROUP stpxLoopGuardGroup2
-- DESCRIPTION "This group is optional for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxMSTGroup
-- DESCRIPTION "This group is optional for implementation of
-- Multiple Spanning Tree Protocol feature."
--
-- GROUP stpxPreferredMSTInstancesGroup
-- DESCRIPTION "This group is optional for implementations
-- of Preferred MST Instance Map feature."
--
-- ::= { stpxMIBCompliances 6 }
--
--
-- stpxMIBCompliance7 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxSstpGroup
-- DESCRIPTION "This group is optional for implementations of
-- Cisco's Shared Spanning Tree Protocol (SSTP)."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxBpduSkewingGroup
-- DESCRIPTION "This is an optional group for implementations of
-- Spanning Tree BPDU Skewing feature."
--
-- GROUP stpxFastStartGroup2
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- GROUP stpxLoopGuardGroup2
-- DESCRIPTION "This group is optional for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxPreferredMSTInstancesGroup
-- DESCRIPTION "This group is optional for implementations
-- of Preferred MST Instance Map feature."
--
-- GROUP stpxFastStartGroup3
-- DESCRIPTION "This group is optional for implementations
-- of Bpdu Guard and Bpdu Filter feature."
--
-- GROUP stpxUplinkGroup2
-- DESCRIPTION "This group is optional for implementations
-- of UplinkFast feature."
--
-- GROUP stpxBackboneGroup2
-- DESCRIPTION "This group is optional for implementations
-- of BackboneFast feature."
--
-- GROUP stpxMSTGroup2
-- DESCRIPTION "This group is optional for implementation of
-- Multiple Spanning Tree Protocol feature."
--
-- GROUP stpxRSTPGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid Spanning Tree Protocol feature."
--
-- GROUP stpxRPVSTGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid PVST+ feature."
-- ::= { stpxMIBCompliances 7 }
--
-- stpxMIBCompliance8 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxSstpGroup
-- DESCRIPTION "This group is optional for implementations of
-- Cisco's Shared Spanning Tree Protocol (SSTP)."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxBpduSkewingGroup
-- DESCRIPTION "This is an optional group for implementations of
-- Spanning Tree BPDU Skewing feature."
--
-- GROUP stpxFastStartGroup2
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- GROUP stpxLoopGuardGroup2
-- DESCRIPTION "This group is optional for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxPreferredMSTInstancesGroup
-- DESCRIPTION "This group is optional for implementations
-- of Preferred MST Instance Map feature."
--
-- GROUP stpxFastStartGroup3
-- DESCRIPTION "This group is optional for implementations
-- of Bpdu Guard and Bpdu Filter feature."
--
-- GROUP stpxUplinkGroup2
-- DESCRIPTION "This group is optional for implementations
-- of UplinkFast feature."
--
-- GROUP stpxBackboneGroup2
-- DESCRIPTION "This group is optional for implementations
-- of BackboneFast feature."
--
-- GROUP stpxMSTGroup2
-- DESCRIPTION "This group is optional for implementation of
-- Multiple Spanning Tree Protocol feature."
--
-- GROUP stpxRSTPGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid Spanning Tree Protocol feature."
--
-- GROUP stpxRPVSTGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid PVST+ feature."
--
-- GROUP stpxExtendedSysIDGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Extended System ID feature."
--
-- GROUP stpxNotificationEnableGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- control on the generation of Spanning Tree
-- notifications."
--
-- GROUP stpxFastStartOperModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Spanning Tree Port Fast Start Oper Mode feature."
--
-- ::= { stpxMIBCompliances 8 }
--
-- stpxMIBCompliance9 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxSstpGroup
-- DESCRIPTION "This group is optional for implementations of
-- Cisco's Shared Spanning Tree Protocol (SSTP)."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxBpduSkewingGroup
-- DESCRIPTION "This is an optional group for implementations of
-- Spanning Tree BPDU Skewing feature."
--
-- GROUP stpxFastStartGroup2
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- GROUP stpxLoopGuardGroup2
-- DESCRIPTION "This group is optional for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxFastStartGroup3
-- DESCRIPTION "This group is optional for implementations
-- of Bpdu Guard and Bpdu Filter feature."
--
-- GROUP stpxUplinkGroup2
-- DESCRIPTION "This group is optional for implementations
-- of UplinkFast feature."
--
-- GROUP stpxBackboneGroup2
-- DESCRIPTION "This group is optional for implementations
-- of BackboneFast feature."
--
-- GROUP stpxRSTPGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid Spanning Tree Protocol feature."
--
-- GROUP stpxRPVSTGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid PVST+ feature."
--
-- GROUP stpxExtendedSysIDGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Extended System ID feature."
--
-- GROUP stpxNotificationEnableGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- control on the generation of Spanning Tree
-- notifications."
--
-- GROUP stpxFastStartOperModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Spanning Tree Port Fast Start Oper Mode feature."
--
-- GROUP stpxMSTGroup3
-- DESCRIPTION "This group is mandatory for implementation of
-- Multiple Spanning Tree Protocol on the device."
--
-- GROUP stpxSMSTGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting IEEE MST on the device."
--
-- GROUP stpxSMSTInstanceGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTInstanceEditGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance edit information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTPortStatusGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port status information for Multiple Spanning
-- Tree Protocol on the device."
--
-- GROUP stpxSMSTPortHelloTimeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port hello time information for IEEE MST
-- on the device."
--
-- ::= { stpxMIBCompliances 9 }
--
-- stpxMIBCompliance10 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxSstpGroup
-- DESCRIPTION "This group is optional for implementations of
-- Cisco's Shared Spanning Tree Protocol (SSTP)."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxBpduSkewingGroup
-- DESCRIPTION "This is an optional group for implementations of
-- Spanning Tree BPDU Skewing feature."
--
-- GROUP stpxFastStartGroup2
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- GROUP stpxLoopGuardGroup2
-- DESCRIPTION "This group is optional for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxFastStartGroup3
-- DESCRIPTION "This group is optional for implementations
-- of Bpdu Guard and Bpdu Filter feature."
--
-- GROUP stpxUplinkGroup2
-- DESCRIPTION "This group is optional for implementations
-- of UplinkFast feature."
--
-- GROUP stpxBackboneGroup2
-- DESCRIPTION "This group is optional for implementations
-- of BackboneFast feature."
--
-- GROUP stpxRSTPGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid Spanning Tree Protocol feature."
--
-- GROUP stpxRPVSTGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid PVST+ feature."
--
-- GROUP stpxExtendedSysIDGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Extended System ID feature."
--
-- GROUP stpxNotificationEnableGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- control on the generation of Spanning Tree
-- notifications."
--
-- GROUP stpxFastStartOperModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Spanning Tree Port Fast Start Oper Mode feature."
--
-- GROUP stpxMSTGroup3
-- DESCRIPTION "This group is mandatory for implementation of
-- Multiple Spanning Tree Protocol on the device."
--
-- GROUP stpxSMSTGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting IEEE MST on the device."
--
-- GROUP stpxSMSTInstanceGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTInstanceEditGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance edit information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTPortStatusGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port status information for Multiple Spanning
-- Tree Protocol on the device."
--
-- GROUP stpxSMSTPortHelloTimeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port hello time information for IEEE MST
-- on the device."
--
-- GROUP stpxSMSTInstanceCISTGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting Common and Internal Spanning Tree (CIST)
-- information for IEEE MST on the device."
--
-- ::= { stpxMIBCompliances 10 }
--
-- stpxMIBCompliance11 MODULE-COMPLIANCE
-- STATUS deprecated
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxSstpGroup
-- DESCRIPTION "This group is optional for implementations of
-- Cisco's Shared Spanning Tree Protocol (SSTP)."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxBpduSkewingGroup
-- DESCRIPTION "This is an optional group for implementations of
-- Spanning Tree BPDU Skewing feature."
--
-- GROUP stpxFastStartGroup2
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- GROUP stpxLoopGuardGroup2
-- DESCRIPTION "This group is optional for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxFastStartGroup3
-- DESCRIPTION "This group is optional for implementations
-- of Bpdu Guard and Bpdu Filter feature."
--
-- GROUP stpxUplinkGroup2
-- DESCRIPTION "This group is optional for implementations
-- of UplinkFast feature."
--
-- GROUP stpxBackboneGroup2
-- DESCRIPTION "This group is optional for implementations
-- of BackboneFast feature."
--
-- GROUP stpxRSTPGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid Spanning Tree Protocol feature."
--
-- GROUP stpxRPVSTGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid PVST+ feature."
--
-- GROUP stpxExtendedSysIDGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Extended System ID feature."
--
-- GROUP stpxNotificationEnableGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- control on the generation of Spanning Tree
-- notifications."
--
-- GROUP stpxFastStartOperModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Spanning Tree Port Fast Start Oper Mode feature."
--
-- GROUP stpxMSTGroup3
-- DESCRIPTION "This group is mandatory for implementation of
-- Multiple Spanning Tree Protocol on the device."
--
-- GROUP stpxSMSTGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting IEEE MST on the device."
--
-- GROUP stpxSMSTInstanceGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTInstanceEditGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance edit information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTPortStatusGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port status information for Multiple Spanning
-- Tree Protocol on the device."
--
-- GROUP stpxSMSTPortHelloTimeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port hello time information for IEEE MST
-- on the device."
--
-- GROUP stpxSMSTInstanceCISTGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting Common and Internal Spanning Tree (CIST)
-- information for IEEE MST on the device."
--
-- GROUP stpxPathCostOperModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting operational spanning tree path cost
-- mode."
--
-- ::= { stpxMIBCompliances 11 }
--
-- stpxMIBCompliance12 MODULE-COMPLIANCE
-- STATUS current
-- DESCRIPTION
-- "The compliance statement for entities which implement
-- Cisco STP Extensions MIB."
-- MODULE - - this module
-- - - no MANDATORY-GROUPS
--
-- GROUP stpxUplinkGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the UplinkFast capability."
--
-- GROUP stpxSstpGroup
-- DESCRIPTION "This group is optional for implementations of
-- Cisco's Shared Spanning Tree Protocol (SSTP)."
--
-- GROUP stpxPreferredVlansGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the Preferred VLANs capability."
--
-- GROUP stpxNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpxBackboneGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the BackboneFast capability."
--
-- GROUP stpxRootGuardGroup
-- DESCRIPTION "This group is mandatory for implementations
-- of the RootGuard capability."
--
-- GROUP stpxRootInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation required to implement."
--
-- GROUP stpx4kVlanGroup
-- DESCRIPTION "This group must be implemented by the
-- entities which support the range of VlanIndex
-- between 1024 and 4095."
--
-- GROUP stpxSpanningTreeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP and PVSTP+"
--
-- GROUP stpxMISTPGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support MISTP."
--
-- GROUP stpxLongPathCostModeGroup
-- DESCRIPTION "This group must be implemented by the entities
-- that support 32 bits spannning tree path cost
-- value."
--
-- GROUP stpxPVSTVlanGroup
-- DESCRIPTION "This group is optional for implementations
-- of the Spanning Tree PVST+ Protocol VLAN
-- configuration."
--
-- GROUP stpxMISTPGroup2
-- DESCRIPTION "This group is optional for implementations
-- that support MISTP with the range of VlanIndex
-- up to 4095."
--
-- GROUP stpxLoopInconsistencyNotificationsGroup
-- DESCRIPTION "The notifications which a STP extension
-- implementation is required to implement."
--
-- GROUP stpxBpduSkewingGroup
-- DESCRIPTION "This is an optional group for implementations of
-- Spanning Tree BPDU Skewing feature."
--
-- GROUP stpxFastStartGroup2
-- DESCRIPTION "This stpxFastStartGroup is an optional group
-- containing objects providing information about
-- Spanning Tree Port Fast Start feature."
--
-- GROUP stpxLoopGuardGroup2
-- DESCRIPTION "This group is optional for implementations
-- of the LoopGuard capability."
--
-- GROUP stpxFastStartGroup3
-- DESCRIPTION "This group is optional for implementations
-- of Bpdu Guard and Bpdu Filter feature."
--
-- GROUP stpxUplinkGroup2
-- DESCRIPTION "This group is optional for implementations
-- of UplinkFast feature."
--
-- GROUP stpxBackboneGroup2
-- DESCRIPTION "This group is optional for implementations
-- of BackboneFast feature."
--
-- GROUP stpxRSTPGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid Spanning Tree Protocol feature."
--
-- GROUP stpxRSTPTransmitHoldCountGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid Spanning Tree Protocol feature."
--
-- GROUP stpxRPVSTGroup
-- DESCRIPTION "This group is optional for implementation of
-- Rapid PVST+ feature."
--
-- GROUP stpxExtendedSysIDGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Extended System ID feature."
--
-- GROUP stpxNotificationEnableGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- control on the generation of Spanning Tree
-- notifications."
--
-- GROUP stpxFastStartOperModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- Spanning Tree Port Fast Start Oper Mode feature."
--
-- GROUP stpxMSTGroup4
-- DESCRIPTION "This group is mandatory for implementation of
-- Multiple Spanning Tree Protocol on the device."
--
-- GROUP stpxSMSTGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting IEEE MST on the device."
--
-- GROUP stpxSMSTMaxHopCountGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- maximum hop count configuration on the device."
--
-- GROUP stpxSMSTInstanceGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTInstanceEditGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting MST instance edit information for
-- IEEE MST on the device."
--
-- GROUP stpxSMSTPortStatusGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port status information for Multiple Spanning
-- Tree Protocol on the device."
--
-- GROUP stpxSMSTPortHelloTimeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- port hello time information for IEEE MST
-- on the device."
--
-- GROUP stpxSMSTInstanceCISTGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting Common and Internal Spanning Tree (CIST)
-- information for IEEE MST on the device."
--
-- GROUP stpxPathCostOperModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting operational spanning tree path cost
-- mode."
--
-- GROUP stpxSMSTPortMSTModeGroup
-- DESCRIPTION "This group is mandatory for implementation of
-- supporting port MST mode configuration."
--
-- GROUP stpxSMSTConfigDigestGroup
-- DESCRIPTION "This group is optional for implementation of
-- supporting IEEE MST on the device."
--
-- ::= { stpxMIBCompliances 12 }
--
-- units of conformance
--
-- stpxUplinkGroup OBJECT-GROUP
-- OBJECTS { stpxUplinkFastEnabled,
-- stpxUplinkFastTransitions,
-- stpxUplinkStationLearningGenRate,
-- stpxUplinkStationLearningFrames }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects for managing the UplinkFast
-- capability."
-- ::= { stpxMIBGroups 1 }
--
-- stpxPreferredVlansGroup OBJECT-GROUP
-- OBJECTS { stpxPreferredVlansMap }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects for indicating preferred VLANs."
-- ::= { stpxMIBGroups 2 }
--
-- stpxSstpGroup OBJECT-GROUP
-- OBJECTS { stpxInconsistentState }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects to support Cisco's Shared Spanning
-- Tree Protocol (SSTP)."
-- ::= { stpxMIBGroups 3 }
--
-- stpxNotificationsGroup NOTIFICATION-GROUP
-- NOTIFICATIONS { stpxInconsistencyUpdate }
-- STATUS current
-- DESCRIPTION
-- "The notifications which a STP extension implementation is
-- required to implement."
-- ::= { stpxMIBGroups 4 }
--
-- stpxBackboneGroup OBJECT-GROUP
-- OBJECTS { stpxBackboneFastEnabled,
-- stpxBackboneFastInInferiorBPDUs,
-- stpxBackboneFastInRLQRequestPDUs,
-- stpxBackboneFastInRLQResponsePDUs,
-- stpxBackboneFastOutRLQRequestPDUs,
-- stpxBackboneFastOutRLQResponsePDUs }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects for managing the BackboneFast
-- capability."
-- ::= { stpxMIBGroups 5 }
--
-- stpxRootGuardGroup OBJECT-GROUP
-- OBJECTS { stpxRootGuardConfigEnabled,
-- stpxRootInconsistencyState
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects to support root guard
-- capabilities."
-- ::= { stpxMIBGroups 6 }
--
-- stpxRootInconsistencyNotificationsGroup NOTIFICATION-GROUP
-- NOTIFICATIONS { stpxRootInconsistencyUpdate }
-- STATUS current
-- DESCRIPTION
-- "The notifications which a STP root guard
-- implementation is required to implement."
-- ::= { stpxMIBGroups 7 }
--
-- stpx4kVlanGroup OBJECT-GROUP
-- OBJECTS { stpxPreferredVlansMap2k,
-- stpxPreferredVlansMap3k,
-- stpxPreferredVlansMap4k }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing information
-- for VLANS with VlanIndex from 1024 to 4095."
-- ::= { stpxMIBGroups 8 }
--
-- stpxSpanningTreeGroup OBJECT-GROUP
-- OBJECTS { stpxSpanningTreeType }
-- STATUS current
-- DESCRIPTION
-- "An object selecting what kind of spanning tree protocol."
-- ::= { stpxMIBGroups 9 }
--
-- stpxMISTPGroup OBJECT-GROUP
-- OBJECTS { stpxMISTPInstanceNumber,
-- stpxMISTPInstanceEnable,
-- stpxVlanMISTPInstMapInstIndex,
-- stpxVlanMISTPInstMapEditInstIndex,
-- stpxPreferredMISTPInstancesMap }
-- STATUS current
-- DESCRIPTION
-- "A collection objects managing the information of
-- MISTP feature."
-- ::= { stpxMIBGroups 10 }
--
-- stpxLongPathCostModeGroup OBJECT-GROUP
-- OBJECTS { stpxSpanningTreePathCostMode,
-- stpxLongStpPortPathCost }
-- STATUS current
-- DESCRIPTION
-- "A collection objects managing the information of
-- spanning tree path cost in 32 bits value."
-- ::= { stpxMIBGroups 11 }
--
-- stpxPVSTVlanGroup OBJECT-GROUP
-- OBJECTS { stpxPVSTVlanEnable }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects managing the information
-- of Spanning Tree PVST+ protocol VLAN configuration."
-- ::= { stpxMIBGroups 12 }
--
-- stpxMISTPGroup2 OBJECT-GROUP
-- OBJECTS { stpxMISTPInstanceVlansMapped,
-- stpxMISTPInstanceVlansMapped2k,
-- stpxMISTPInstanceVlansMapped3k,
-- stpxMISTPInstanceVlansMapped4k }
-- STATUS current
-- DESCRIPTION
-- "A collection objects managing the information of
-- MISTP instances to VLAN mapping with the range of
-- VlanIndex up to 4095."
-- ::= { stpxMIBGroups 13 }
--
-- stpxLoopGuardGroup OBJECT-GROUP
-- OBJECTS { stpxLoopGuardConfigEnabled,
-- stpxLoopInconsistencyState
-- }
-- STATUS deprecated
-- DESCRIPTION
-- "A collection of objects to support LoopGuard
-- capabilities."
-- ::= { stpxMIBGroups 14 }
--
-- stpxLoopInconsistencyNotificationsGroup NOTIFICATION-GROUP
-- NOTIFICATIONS { stpxLoopInconsistencyUpdate }
-- STATUS current
-- DESCRIPTION
-- "The notifications which a STP LoopGuard
-- implementation is required to implement."
-- ::= { stpxMIBGroups 15 }
--
-- stpxFastStartGroup OBJECT-GROUP
-- OBJECTS { stpxFastStartBpduGuardEnable,
-- stpxFastStartBpduFilterEnable,
-- stpxFastStartPortEnable }
-- STATUS deprecated
-- DESCRIPTION
-- "A collection of objects to support Spanning Tree Port
-- Fast Start feature."
-- ::= { stpxMIBGroups 16 }
--
-- stpxBpduSkewingGroup OBJECT-GROUP
-- OBJECTS { stpxBpduSkewingDetectionEnable,
-- stpxBpduSkewingLastSkewDuration,
-- stpxBpduSkewingWorstSkewDuration,
-- stpxBpduSkewingWorstSkewTime }
-- STATUS current
-- DESCRIPTION
-- "This is an optional group with a collection of
-- objects to support Spanning Tree BPDU Skewing feature."
-- ::= { stpxMIBGroups 17 }
--
-- stpxFastStartGroup2 OBJECT-GROUP
-- OBJECTS { stpxFastStartBpduGuardEnable,
-- stpxFastStartBpduFilterEnable,
-- stpxFastStartPortMode,
-- stpxFastStartGlobalDefaultMode
-- }
-- STATUS current
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support Fast Start global default mode on the device."
-- ::= { stpxMIBGroups 18 }
--
-- stpxLoopGuardGroup2 OBJECT-GROUP
-- OBJECTS { stpxLoopInconsistencyState,
-- stpxLoopGuardConfigMode,
-- stpxLoopGuardGlobalDefaultMode
-- }
-- STATUS current
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support Loop Guard global default mode on the device."
-- ::= { stpxMIBGroups 19 }
--
-- stpxMSTGroup OBJECT-GROUP
-- OBJECTS { stpxMSTMaxInstanceNumber,
-- stpxMSTRegionName,
-- stpxMSTRegionRevision,
-- stpxMSTInstanceVlansMapped,
-- stpxMSTInstanceVlansMapped2k,
-- stpxMSTInstanceVlansMapped3k,
-- stpxMSTInstanceVlansMapped4k,
-- stpxMSTInstanceRemainingHopCount,
-- stpxMSTRegionEditBufferStatus,
-- stpxMSTRegionEditBufferOperation,
-- stpxMSTRegionEditName,
-- stpxMSTRegionEditRevision,
-- stpxMSTInstanceEditVlansMap,
-- stpxMSTInstanceEditVlansMap2k,
-- stpxMSTInstanceEditVlansMap3k,
-- stpxMSTInstanceEditVlansMap4k,
-- stpxMSTPortAdminLinkType, - - deprecated
-- stpxMSTPortOperLinkType, - - deprecated
-- stpxMSTPortProtocolMigration, - - deprecated
-- stpxMSTPortStatus,
-- stpxMSTPortRoleValue, - - deprecated
-- stpxMSTMaxHopCount - - deprecated
-- }
-- STATUS deprecated
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support Multiple Spanning Tree Protocol on the device."
-- ::= { stpxMIBGroups 20 }
--
-- stpxPreferredMSTInstancesGroup OBJECT-GROUP
-- OBJECTS { stpxPreferredMSTInstancesMap }
-- STATUS deprecated
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support Preferred MST Instance Map feature for Multiple
-- Spanning Tree Protocol on the device."
-- ::= { stpxMIBGroups 21 }
--
-- stpxFastStartGroup3 OBJECT-GROUP
-- OBJECTS { stpxFastStartPortBpduGuardMode,
-- stpxFastStartPortBpduFilterMode
-- }
-- STATUS current
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support per port Bpdu Guard and Bpdu Filter mode
-- configuration on the device."
-- ::= { stpxMIBGroups 22 }
--
-- stpxUplinkGroup2 OBJECT-GROUP
-- OBJECTS { stpxUplinkFastOperEnabled }
-- STATUS current
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- manage the UplinkFast capability."
-- ::= { stpxMIBGroups 23 }
--
-- stpxBackboneGroup2 OBJECT-GROUP
-- OBJECTS { stpxBackboneFastOperEnabled }
-- STATUS current
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- manage the BackboneFast capability."
-- ::= { stpxMIBGroups 24 }
--
--
-- stpxMSTGroup2 OBJECT-GROUP
-- OBJECTS { stpxMSTMaxInstanceNumber, - - deprecated
-- stpxMSTRegionName,
-- stpxMSTRegionRevision, - - deprecated
-- stpxMSTInstanceVlansMapped, - - deprecated
-- stpxMSTInstanceVlansMapped2k, - - deprecated
-- stpxMSTInstanceVlansMapped3k, - - deprecated
-- stpxMSTInstanceVlansMapped4k, - - deprecated
-- stpxMSTInstanceRemainingHopCount, - - deprecated
-- stpxMSTRegionEditBufferStatus,
-- stpxMSTRegionEditBufferOperation,
-- stpxMSTRegionEditName,
-- stpxMSTRegionEditRevision, - - deprecated
-- stpxMSTInstanceEditVlansMap, - - deprecated
-- stpxMSTInstanceEditVlansMap2k, - - deprecated
-- stpxMSTInstanceEditVlansMap3k, - - deprecated
-- stpxMSTInstanceEditVlansMap4k, - - deprecated
-- stpxMSTPortStatus, - - deprecated
-- stpxMSTMaxHopCount - - deprecated
-- }
-- STATUS deprecated
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support Multiple Spanning Tree Protocol on the device."
-- ::= { stpxMIBGroups 25 }
--
-- stpxRSTPGroup OBJECT-GROUP
-- OBJECTS { stpxRSTPPortAdminLinkType,
-- stpxRSTPPortOperLinkType,
-- stpxRSTPPortProtocolMigration,
-- stpxRSTPPortRoleValue
-- }
-- STATUS current
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support Rapid Spanning Tree Protocol on the device."
-- ::= { stpxMIBGroups 26 }
--
-- stpxRPVSTGroup OBJECT-GROUP
-- OBJECTS {
-- stpxRPVSTPortStatus
-- }
-- STATUS current
-- DESCRIPTION
-- "An optional group with a collection of objects to
-- support Rapid PVST+ on the device."
-- ::= { stpxMIBGroups 27 }
--
-- stpxExtendedSysIDGroup OBJECT-GROUP
-- OBJECTS {
-- stpxExtendedSysIDAdminEnabled,
-- stpxExtendedSysIDOperEnabled
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects to manage the
-- Extended System ID capability."
-- ::= { stpxMIBGroups 28 }
--
-- stpxNotificationEnableGroup OBJECT-GROUP
-- OBJECTS { stpxNotificationEnable }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing control on the
-- generation of Spanning Tree notifications."
-- ::= { stpxMIBGroups 29 }
--
-- stpxFastStartOperModeGroup OBJECT-GROUP
-- OBJECTS { stpxFastStartOperMode }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing Spanning Tree
-- Port Fast Start Operatioanl information on a port."
-- ::= { stpxMIBGroups 30 }
--
-- stpxMSTGroup3 OBJECT-GROUP
-- OBJECTS {
-- stpxMSTRegionName,
-- stpxMSTRegionEditBufferStatus,
-- stpxMSTRegionEditBufferOperation,
-- stpxMSTRegionEditName,
-- stpxMSTMaxHopCount - - deprecated
-- }
-- STATUS deprecated
-- DESCRIPTION
-- "A collection of objects providing support
-- for Multiple Spanning Tree Protocol on the device."
-- ::= { stpxMIBGroups 31 }
--
-- stpxSMSTGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTMaxInstances,
-- stpxSMSTMaxInstanceID,
-- stpxSMSTRegionRevision,
-- stpxSMSTRegionEditRevision
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing support for
-- IEEE MST on the device."
-- ::= { stpxMIBGroups 32 }
--
-- stpxSMSTInstanceGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTInstanceVlansMapped1k2k,
-- stpxSMSTInstanceVlansMapped3k4k,
-- stpxSMSTInstanceRemainingHopCount
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing support for
-- MST instance information for IEEE MST on the device."
-- ::= { stpxMIBGroups 33 }
--
-- stpxSMSTInstanceEditGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTInstanceEditVlansMap1k2k,
-- stpxSMSTInstanceEditVlansMap3k4k,
-- stpxSMSTInstanceEditRowStatus
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing support for MST
-- instance edit information for IEEE MST on the device."
-- ::= { stpxMIBGroups 34 }
--
-- stpxSMSTPortStatusGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTPortStatus
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing support for
-- port status information for MST Protocol on the
-- device."
-- ::= { stpxMIBGroups 35 }
--
-- stpxSMSTPortHelloTimeGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTPortAdminHelloTime,
-- stpxSMSTPortConfigedHelloTime,
-- stpxSMSTPortOperHelloTime
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing support for per
-- port hello time information for IEEE MST on the device."
-- ::= { stpxMIBGroups 36 }
--
-- stpxSMSTInstanceCISTGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTInstanceCISTRegionalRoot,
-- stpxSMSTInstanceCISTIntRootCost
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing information about
-- Common and Internal Spanning Tree (CIST) for IEEE
-- MST on the device."
-- ::= { stpxMIBGroups 37 }
--
-- stpxPathCostOperModeGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSpanningTreePathCostOperMode
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing information about
-- operational spanning tree path cost mode."
-- ::= { stpxMIBGroups 38 }
--
-- stpxRSTPTransmitHoldCountGroup OBJECT-GROUP
-- OBJECTS {
-- stpxRSTPTransmitHoldCount
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing information for
-- configuration of transmit hold count for Rapid Spanning
-- Tree Protocol."
-- ::= { stpxMIBGroups 39 }
--
-- stpxSMSTPortMSTModeGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTPortAdminMSTMode,
-- stpxSMSTPortOperMSTMode
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing information for port
-- MST mode configuration on the device."
-- ::= { stpxMIBGroups 40 }
--
-- stpxSMSTMaxHopCountGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTMaxHopCount
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing information for
-- configuration of IEEE MST maximum hop count."
-- ::= { stpxMIBGroups 41 }
--
-- stpxSMSTConfigDigestGroup OBJECT-GROUP
-- OBJECTS {
-- stpxSMSTConfigDigest,
-- stpxSMSTConfigPreStandardDigest
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing information for
-- MST configuration digests on the device."
-- ::= { stpxMIBGroups 42 }
--
-- stpxMSTGroup4 OBJECT-GROUP
-- OBJECTS {
-- stpxMSTRegionName,
-- stpxMSTRegionEditBufferStatus,
-- stpxMSTRegionEditBufferOperation,
-- stpxMSTRegionEditName
-- }
-- STATUS current
-- DESCRIPTION
-- "A collection of objects providing support
-- for Multiple Spanning Tree Protocol on the device."
-- ::= { stpxMIBGroups 43 }
--
END
View Git Blame Copy Permalink