WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/cisco/CISCO-LWAPP-MESH-MIB

3208 lines
118 KiB
Plaintext
Raw Permalink Blame History

-- *******************************************************************
-- CISCO-LWAPP-MESH-MIB.my
-- February,2007 Devesh Pujari
--
-- Copyright (c) 2006-2007, 2010, 2015-2021 by Cisco Systems Inc.
-- All rights reserved.
-- *******************************************************************
CISCO-LWAPP-MESH-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Unsigned32,
Integer32,
Gauge32,
NOTIFICATION-TYPE
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
TruthValue,
TimeStamp,
MacAddress,
TimeInterval,
RowStatus
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
cLApSysMacAddress,
cLApName
FROM CISCO-LWAPP-AP-MIB
CLDot11Channel
FROM CISCO-LWAPP-TC-MIB
Unsigned64
FROM CISCO-TC
ciscoMgmt
FROM CISCO-SMI;
-- ********************************************************************
-- * MODULE IDENTITY
-- ********************************************************************
ciscoLwappMeshMIB MODULE-IDENTITY
LAST-UPDATED "202104270000Z"
ORGANIZATION "Cisco Systems Inc."
CONTACT-INFO
"Cisco Systems,
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
Email: cs-wnbu-snmp@cisco.com"
DESCRIPTION
"This MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
(LWAPP) tunnel from Light-weight Access Points.
This MIB represents information used in Wireless Mesh
Network. MAP APs associates directly with RAP APs or
with another MAP AP. Each association of AP (MAP-MAP
or RAP-MAP) with another AP forms parent-child
relationship.
The deployment of the controller
(referred to as CC in the diagram), mesh nodes
(RAP and MAP) LWAPP APs, client(MS) and NMS appear
as follows.
+.......+ +.......+
+ + + +
+ NMS + + NMS +
+ + + +
+.......+ +.......+
. .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ RAP + + RAP + + RAP + + RAP + + RAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MAP + + MS + + MAP + + MAP + + MAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . .. .
. . . .. .
. . . .. .
. . . . .
+......+ +......+ +......+ +......+. +......+
+ + + + + + + + + +
+ MAP + + MAP + + MAP + + MAP + + MS +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the
configuration, that includes the WLAN parameters to
the LWAPP APs.
The APs encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Central Controller ( CC )
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity is also referred to as 'controller'.
Mobile Station ( MS )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Station
and client are used interchangeably.
Network Management System ( NMS )
The station from which the administrator manages the
wired and wireless networks.
Mesh Node
A mesh node is defined as a physical or logical entity
in the mesh network participating in forming the mesh
backhaul. RAP and MAP are two types of mesh nodes
supported in mesh network.
Root AP (RAP)
The AP forming the bridge between a wired and a mesh
network with an Ethernet interface to the wired
network and a 802.11 radio interface to the mesh
network
Mesh AP (MAP).
The AP extending wireless coverage similar to a
repeater in a mesh network and consists of a 802.11
uplink and a 802.11 downlink. On a single-radio
backhaul, both uplink and downlink exist on the same
radio and are logical links only. On a multi-radio
backhaul, they may exist on different radios.
Mesh Network
Network starting with the wireless backhaul downlink
of the RAP and all the entities below except any
attached network to the Ethernet link of MAPs. A mesh
network below a single RAP is also referred to as a
'Mesh Sector'.A mesh network consists of mesh nodes.
A single mesh network is always augmented to a single
wired network.
Mesh Link
A logical 802.11 link between two mesh nodes. A single
link is point-to-point. All point-to-multipoint links
are considered as multiple mesh links. Often referred
to as mesh backhaul link.
Mesh Backhaul
A mesh backhaul consists of mesh nodes and mesh links
terminating at a RAP. This necessarily creates a one-
to-one relationship between a 'mesh network', 'mesh
sector' and a 'mesh backhaul' where these terms can be
used interchangeably.
SNR
Signal to Noise ratio on the 802.11 radio.
Bridged network
The bridged network is defined as the network(s)
attached to the Ethernet port of any MAP. There can be
multiple such networks attached to a single mesh
network.
Mesh Node Roaming
A mesh node may change its parent mesh node naturally
when the RF/network condition changes. Child Mesh node
will re-associate and re-authenticate to new parent
mesh node. Mesh Security supports two types of mesh
node roaming.
Intra-controller - LWAPP session is not lost.
Inter-controller - LWAPP session is lost.
AMSDU
Aggregate MAC Service Data Unit. A structure containing
multiple MSDUs, transported within a single (unfragmented)
or multiple (fragmented) Data MPDU.
IDS
Intrusion Detection Sysytem. A software to detect unwanted
attempts at accessing,manipulating, and or disabling of WLC.
ExtendedUA
For 1524 APs, it has two 802.11a radios (slot1, slot2) and
one 802.11b/g radio (slot0). This will enable the client
access on 802.11a (slot1) for 152x series mesh access points
with two 802.11a radios, where the wireless client association
can be done over the 802.11a radio (slot1). With this feature
we are providing an option to enable/disable backhaul client
on another 802.11a radio (slot2) as well. This implies that
a 152x series mesh access points with two 802.11a radios
can carry both backhaul traffic and 802.11a (slot1, slot2)
client traffic over the same radios.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol"
REVISION "202104270000Z"
DESCRIPTION
"Added following objects to clMeshProfileTable
cLMeshProfileDot11bgBhaulRateDot11axMcsIndex
cLMeshProfileDot11bgBhaulRateDot11axSpatialStream
cLMeshProfileDot11aBhaulRateDot11axMcsIndex
cLMeshProfileDot11aBhaulRateDot11axSpatialStream
Deprecated the following compliance groups
- ciscoLwappMeshMIBComplianceR03
- ciscoLwappMeshProfileConfigGroup
Added the following compliance groups
- ciscoLwappMeshMIBComplianceR04
- ciscoLwappMeshProfileConfigGroupRev1"
REVISION "201904110000Z"
DESCRIPTION
"Added following scaler object
clMeshIsCacEnabled"
REVISION "201809120000Z"
DESCRIPTION
"Added table clMeshProfileTable
Added following objects in clMeshNodeTable
clMeshNodeBlockChild
clMeshNodeBhaulDataRateType
clMeshNodeBhaulDataRate
clMeshNodeBhaulDataRateMcsIndex
clMeshNodeBhaulDataRateDot11acSpatialStream
Added scalar clMeshPskInUseKeyIndex"
REVISION "201706090000Z"
DESCRIPTION
"Added following objects,
clMeshPskKeyProvisionEnable
clMeshPskKeyWindowEnable
clMeshEthenetBridgingVlanTransparent
clMeshRAPDownlinkBackhaul
Added following table,
clMeshAtfStatsTable."
REVISION "201010070000Z"
DESCRIPTION
"Deprecated clMeshNodeBackhaulDataRate and replaced
it with clMeshNodeBHDataRate.
Deprecated ciscoLwappMeshConfigGroupSup1 and
ciscoLwappMeshMIBComplianceR01.
Added ciscoLwappMeshConfigGroupSup2 and
ciscoLwappMeshMIBComplianceR02.
Modified the description of the notification object,
ciscoLwappMeshAbateHighSNR."
REVISION "201003030000Z"
DESCRIPTION
"Added following new objects to clMeshNodeTable:
clMeshNodeChildCount, clMeshNodeBackhaulRadio
Added following new objects to ciscoLwappMeshGlobalConfig.
clMeshHighSNRThresholdAbate,
clMeshHighSNRThresholdOnset,
clMeshExcessiveHopCountThreshold,
clMeshExcessiveMapChildThreshold,
clMeshPublicSafetyBackhaulGlobal,
clMeshisAMSDUEnable,
clMeshIsIdsEnable,
clMeshIsDCAChannelsEnable,
clMeshIsExtendedUAEnable ,
clMeshIsBDomainChannelsEnable
Added following new notifications control objects.
clMeshHighSNRNotifEnabled,
clMeshConsoleLoginNotifEnabled,
clMeshDefaultBridgeGroupNameNotifEnabled,
clMeshExcessiveHopCountNotifEnabled,
clMeshExcessiveChildrenNotifEnabled
Added following new notifications.
ciscoLwappMeshDefaultBridgeGroupName,
ciscoLwappMeshExcessiveHopCount,
ciscoLwappMeshExcessiveChildren,
ciscoLwappMeshAbateHighSNR,
ciscoLwappMeshOnsetHighSNR
Added following new notification Groups.
ciscoLwappMeshNotifControlGroupSup1 is a supplement to
ciscoLwappMeshNotifControlGroup,
ciscoLwappMeshNotifsGroupSup1 is a supplement to
ciscoLwappMeshNotifsGroup.
Added ciscoLwappMeshConfigGroupSup1, which deprecates
ciscoLwappMeshConfigGroup.
Added ciscoLwappMeshMIBComplianceR01, which deprecates
ciscoLwappMeshMIBCompliance
Deprecated the following object.
clMeshNodePublicSafetyBackhaul"
REVISION "200703090000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 616 }
ciscoLwappMeshMIBNotifs OBJECT IDENTIFIER
::= { ciscoLwappMeshMIB 0 }
ciscoLwappMeshMIBObjects OBJECT IDENTIFIER
::= { ciscoLwappMeshMIB 1 }
ciscoLwappMeshMIBConform OBJECT IDENTIFIER
::= { ciscoLwappMeshMIB 2 }
ciscoLwappMeshConfig OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBObjects 1 }
ciscoLwappMeshGlobalConfig OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBObjects 2 }
ciscoLwappMeshNeighborsStatus OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBObjects 3 }
ciscoLwappMeshNotifControlConfig OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBObjects 4 }
ciscoLwappMeshMIBNotifObjects OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBObjects 5 }
ciscoLwappMeshGpsObjects OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBObjects 6 }
-- ********************************************************************
-- * Mesh Node configuration
-- ********************************************************************
clMeshNodeTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClMeshNodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents information about the 802.11
LWAPP Access Points that have joined the controller
as part of a mesh network."
::= { ciscoLwappMeshConfig 1 }
clMeshNodeEntry OBJECT-TYPE
SYNTAX ClMeshNodeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a conceptual row in this table.
An entry is created when MAP joins the controller.
The entry is removed when the mesh node lose their
association with the controller due to loss of
communication with controller or when a mesh node
is reset."
INDEX { cLApSysMacAddress }
::= { clMeshNodeTable 1 }
ClMeshNodeEntry ::= SEQUENCE {
clMeshNodeRole INTEGER,
clMeshNodeGroupName SnmpAdminString,
clMeshNodeBackhaul INTEGER,
clMeshNodeBackhaulDataRate Unsigned32,
clMeshNodeEthernetBridge TruthValue,
clMeshNodeEthernetLinkStatus INTEGER,
clMeshNodePublicSafetyBackhaul TruthValue,
clMeshNodeParentMacAddress MacAddress,
clMeshNodeHeaterStatus INTEGER,
clMeshNodeInternalTemp Integer32,
clMeshNodeType INTEGER,
clMeshNodeHops Gauge32,
clMeshNodeChildCount Gauge32,
clMeshNodeBackhaulRadio INTEGER,
clMeshNodeBHDataRate INTEGER,
clMeshDaisyChainEnabled TruthValue,
clMeshPrefParentMacAddress MacAddress,
clMeshNodeBGNStrictMatch TruthValue,
clMeshNodeVlanEnabled TruthValue,
clMeshNodeNativeVlanId Unsigned32,
clMeshNodePskKeyClear TruthValue,
clMeshNodeRAPDownlinkBackhaul INTEGER,
clMeshNodeBlockChild TruthValue,
clMeshNodeBhaulDataRateType INTEGER,
clMeshNodeBhaulDataRate INTEGER,
clMeshNodeBhaulDataRateMcsIndex Unsigned32,
clMeshNodeBhaulDataRateDot11acSpatialStream Unsigned32,
clMeshNodeBhaulDataRateDot11axSpatialStream Unsigned32
}
clMeshNodeRole OBJECT-TYPE
SYNTAX INTEGER {
map(1),
rap(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the role of mesh AP which has
joined the controller. See glossary section above
for detail about MAP and RAP.
map - AP is configured as mesh.
rap - AP is configured as root."
::= { clMeshNodeEntry 1 }
clMeshNodeGroupName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..10))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the group name of the mesh
sector. MAP AP will join the mesh sector which has the
same group name configured on RAP AP."
::= { clMeshNodeEntry 2 }
clMeshNodeBackhaul OBJECT-TYPE
SYNTAX INTEGER {
dot11a(1),
dot11b(2),
dot11g(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents 802.11 interface type of the
backhaul link. See Mesh Link in glossary section for
more detail on backhaul link.
dot11a - 802.11a radio is used as backhaul link.
dot11b - 802.11b radio is used as backhaul link.
dot11g - 802.11g radio is used as backhaul link."
::= { clMeshNodeEntry 3 }
clMeshNodeBackhaulDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Kbps"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object represents the rate at which packets are sent
on the backhaul link. This object has been deprecated
for clMeshNodeBHDataRate."
::= { clMeshNodeEntry 4 }
clMeshNodeEthernetBridge OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether ethernet bridge is
enabled or not.
A value of 'true' indicates ethernet bridging is enable
on this mesh node. A value of 'false indicates ethernet
bridging is not enable on this mesh node. Ethernet bridging
can be enabled on RAP or MAP."
::= { clMeshNodeEntry 5 }
clMeshNodeEthernetLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents whetherthe link is up or down on
the ethernet port of the RAP or MAP.
up - ethernet link is up.
down - ethernet link is down."
::= { clMeshNodeEntry 6 }
clMeshNodePublicSafetyBackhaul OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"4.9Ghz considered to be public safety band and is
limited to some service providers. A value of true
indicates that 4.9 Ghz can be used on backhaul link
by selecting channel on the 802.11a backhaul radio.
Since public safety is now set at the controller level
rather then at the AP level, use of this variable is deprecated,
and the global setting clMeshPublicSafetyBackhaulGlobal should
be used instead."
::= { clMeshNodeEntry 7 }
clMeshNodeParentMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the MAC address of a parent
mesh node. In case of RAP this object will
return 0000000000000."
::= { clMeshNodeEntry 8 }
clMeshNodeHeaterStatus OBJECT-TYPE
SYNTAX INTEGER {
on(1),
off(2)
}
UNITS "Percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the heater status of the
mesh node.
on - heater is in operation
off - heater is not operation."
::= { clMeshNodeEntry 9 }
clMeshNodeInternalTemp OBJECT-TYPE
SYNTAX Integer32
UNITS "degree Celsius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the internal temperature
of mesh node in celsius."
::= { clMeshNodeEntry 10 }
clMeshNodeType OBJECT-TYPE
SYNTAX INTEGER {
indoor(1),
outdoor(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the type of mesh node.
indoor - Mesh node which is manufactured to be used
inside the building.
outdoor - Mesh node which can be used outside building
in open environment."
::= { clMeshNodeEntry 11 }
clMeshNodeHops OBJECT-TYPE
SYNTAX Gauge32
UNITS "hops"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the number of hops a MAP mesh node
is from RAP. When the clMeshNodeRole is set to 'RAP' this
object will return a value of zero."
::= { clMeshNodeEntry 12 }
clMeshNodeChildCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the number of children MAPs of a RAP or
a MAP."
DEFVAL { 0 }
::= { clMeshNodeEntry 13 }
clMeshNodeBackhaulRadio OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
dot11bg(2),
dot11a(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the type of radio used for backhaul
access.
unknown (1) unsupported APs
dot11bg (2) The value dot11b sets the 802.11b radio as
backhaul radio
dot11a (3) The value dot11a sets the 802.11a radio as
backhaul radio"
DEFVAL { dot11a }
::= { clMeshNodeEntry 14 }
clMeshNodeBHDataRate OBJECT-TYPE
SYNTAX INTEGER {
mbps1(1),
mbps2(2),
mbps5point5(3),
mbps6(4),
mbps9(5),
mbps11(6),
mbps12(7),
mbps18(8),
mbps24(9),
mbps36(10),
mbps48(11),
mbps54(12),
auto(13),
htMcs0(14),
htMcs1(15),
htMcs2(16),
htMcs3(17),
htMcs4(18),
htMcs5(19),
htMcs6(20),
htMcs7(21),
htMcs8(22),
htMcs9(23),
htMcs10(24),
htMcs11(25),
htMcs12(26),
htMcs13(27),
htMcs14(28),
htMcs15(29),
htMcs16(30),
htMcs17(31),
htMcs18(32),
htMcs19(33),
htMcs20(34),
htMcs21(35),
htMcs22(36),
htMcs23(37),
vhtMcs0Ss1(38),
vhtMcs1Ss1(39),
vhtMcs2Ss1(40),
vhtMcs3Ss1(41),
vhtMcs4Ss1(42),
vhtMcs5Ss1(43),
vhtMcs6Ss1(44),
vhtMcs7Ss1(45),
vhtMcs8Ss1(46),
vhtMcs9Ss1(47),
vhtMcs0Ss2(48),
vhtMcs1Ss2(49),
vhtMcs2Ss2(50),
vhtMcs3Ss2(51),
vhtMcs4Ss2(52),
vhtMcs5Ss2(53),
vhtMcs6Ss2(54),
vhtMcs7Ss2(55),
vhtMcs8Ss2(56),
vhtMcs9Ss2(57),
vhtMcs0Ss3(58),
vhtMcs1Ss3(59),
vhtMcs2Ss3(60),
vhtMcs3Ss3(61),
vhtMcs4Ss3(62),
vhtMcs5Ss3(63),
vhtMcs6Ss3(64),
vhtMcs7Ss3(65),
vhtMcs8Ss3(66),
vhtMcs9Ss3(67),
default(65535)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the rate at which packets are sent
on the backhaul link. Depending on the backhaul radio type,
denoted by clMeshNodeBackhaul object, data rate will vary.
If the value of clMeshNodeBackhaul object is 'dot11a',
data rates can be one of the following
possible values.
mbps6(4)
mbps9(5)
mbps12(7)
mbps18(8)
mbps24(9)
mbps36(10)
mbps48(11)
mbps54(12)
auto(13)
Additionally following data rates are supported if 802.11a
supports 11n.
htMcs0(14)
htMcs1(15)
htMcs2(16)
htMcs3(17)
htMcs4(18)
htMcs5(19)
htMcs6(20)
htMcs7(21)
htMcs8(22)
htMcs9(23)
htMcs10(24)
htMcs11(25)
htMcs12(26)
htMcs13(27)
htMcs14(28)
htMcs15(29)
If the value of clMeshNodeBackhaul object is 'dot11b',
then data rate can be one of the following possible values.
mbps1(1)
mbps2(2)
mbps5point5(3)
mbps11(6)
auto(13)
If the value of clMeshNodeBackhaul object is 'dot11g',
then data rate can be one of the following possible values.
mbps1(1)
mbps2(2)
mbps5point5(3)
mbps6(4)
mbps9(5)
mbps11(6)
mbps12(7)
mbps18(8)
mbps24(9)
mbps36(10)
mbps48(11)
mbps54(12)
auto(13)"
DEFVAL { mbps6 }
::= { clMeshNodeEntry 15 }
clMeshDaisyChainEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether an AP
operating in mesh mode has daisy chaining mode
enabled. A daisy chain is a wiring scheme in
which multiple devices are wired together in
sequence or in a ring.
A value of 'true' indicates that mesh daisy chaining is
enabled.
A value of 'false' indicates that mesh daisy chaining is
disabled."
::= { clMeshNodeEntry 16 }
clMeshPrefParentMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object represents the MAC address of the
preferred parent for this mesh node."
::= { clMeshNodeEntry 17 }
clMeshNodeBGNStrictMatch OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether an AP
operating in mesh mode needs to have
needs to have strict bridge group matching
enabled or not.
A value of 'true' indicates that strict bridge group
name matching is enabled.
A value of 'false' indicates that strict bridge group
name matching is enabled."
::= { clMeshNodeEntry 18 }
clMeshNodeVlanEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether an AP
operating in mesh mode has VLAN support
enabled. If flexconnect local switching is
enabled, it will return the same value as
cLReapApVlanEnable.
A value of 'true' indicates VLAN support enabled.
A value of 'false' indicates VLAN support disabled."
::= { clMeshNodeEntry 19 }
clMeshNodeNativeVlanId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the native VLAN ID
configured on the AP. If flexconnect local switching is
enabled, it will return the same value as
cLReapApNativeVlanId."
::= { clMeshNodeEntry 20 }
clMeshNodePskKeyClear OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies clearing of PSK key.
A value of 'true' indicates PSK key will be cleared.
A value of 'false' indicates PSK key wont be cleared."
DEFVAL { false }
::= { clMeshNodeEntry 21 }
clMeshNodeRAPDownlinkBackhaul OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
slot0(1),
slot1(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects specifies the current backhaul slot of the RAP.
And also used to configure/change the backhaul slot of the RAP.
slot0 - downlink backhaul access for slot 0 enabled.
slot1 - downlink backhaul access for slot 1 enabled."
::= { clMeshNodeEntry 22 }
clMeshNodeBlockChild OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies Block Child state for the AP.
A value of 'true' indicates block child state is enabled.
A value of 'false' indicates block child state is disabled."
DEFVAL { false }
::= { clMeshNodeEntry 23 }
clMeshNodeBhaulDataRateType OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
dot11abg(2),
dot11nMcs(3),
dot11acMcs(4),
dot11axMcs(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the backhaul tx data rate type for Mesh
AP. And also used to configure/change the mesh backhaul data
rate for AP.
auto - Backhaul tx rate is automatically selected
dot11abg - Backhaul tx rate is 802.11abg, one of 1000, 2000,
5500, 11000, 6000, 9000, 12000, 18000, 24000, 36000,
48000, 54000 in kbps.
dot11n - Backhaul tx rate is one of the 802.11n mcs rate.
dot11ac - Backhaul tx rate is one of the 802.11ac mcs rate.
dot11ax - Backhaul tx rate is one of the 802.11ax mcs rate."
::= { clMeshNodeEntry 24 }
clMeshNodeBhaulDataRate OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
mbps1(1000),
mbps2(2000),
mbps5point5(5500),
mbps11(11000),
mbps6(6000),
mbps9(9000),
mbps12(12000),
mbps18(18000),
mbps24(24000),
mbps36(36000),
mbps48(48000),
mbps54(54000)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the backhaul tx rate in kbps
Backhaul tx rate is one of 1000, 2000, 5500,
11000, 6000, 9000, 12000, 18000, 24000, 36000, 48000, 54000"
::= { clMeshNodeEntry 25 }
clMeshNodeBhaulDataRateMcsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the backhaul tx rate 802.11n/ac mcs index
Backhaul mcs index is between 0 to 31 for 802.11n and 0 to 9
for 802.11ac."
::= { clMeshNodeEntry 26 }
clMeshNodeBhaulDataRateDot11acSpatialStream OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the backhaul rate 802.11ac spatial stream
value of backhaul rate spatial stream is between 1 to 4."
::= { clMeshNodeEntry 27 }
clMeshNodeBhaulDataRateDot11axSpatialStream OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the backhaul rate 802.11ax spatial stream
value. Range of 1 - 4 for 802.11bg and 1 - 8 for 802.11 radio."
::= { clMeshNodeEntry 28 }
clMeshPskTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClMeshPskEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents information about the PSK Keys
configured on the WLC for the MESH AP authentication."
::= { ciscoLwappMeshConfig 2 }
clMeshPskEntry OBJECT-TYPE
SYNTAX ClMeshPskEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table represents the
information about PSK Key."
INDEX { clMeshPskIndex }
::= { clMeshPskTable 1 }
ClMeshPskEntry ::= SEQUENCE {
clMeshPskIndex Unsigned32,
clMeshPskKey OCTET STRING,
clMeshPskTimeStamp SnmpAdminString,
clMeshPskKeyDesc SnmpAdminString,
clMeshPskRowStatus RowStatus
}
clMeshPskIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies the one instance of the PSK.
Maximum five entries are maintained. For each key configuration
old key will be pushed down and new key will be placed at top.
After fifth key configuration, old key will be deleted based on
timestamp and new key will be placed at top of the list."
::= { clMeshPskEntry 1 }
clMeshPskKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (3..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the pre-shared
key used for authenticating mesh AP during joining process."
::= { clMeshPskEntry 2 }
clMeshPskTimeStamp OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the time when the
PSK key was configured on WLC."
::= { clMeshPskEntry 3 }
clMeshPskKeyDesc OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the description for the pre-shared key."
::= { clMeshPskEntry 4 }
clMeshPskRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the status column for this row and used
to create and delete specific instances of rows
in this table."
::= { clMeshPskEntry 5 }
clMeshProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClMeshProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists the configuration for each
Mesh profile."
::= { ciscoLwappMeshConfig 3 }
clMeshProfileEntry OBJECT-TYPE
SYNTAX ClMeshProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing the configuration attributes
that affect the operation of Mesh Access points.
Entries can be added/deleted by explicit management
action from NMS/EMS or through user console."
INDEX { cLMeshProfileName }
::= { clMeshProfileTable 1 }
ClMeshProfileEntry ::= SEQUENCE {
cLMeshProfileName SnmpAdminString,
cLMeshProfileDescr SnmpAdminString,
cLMeshProfileASTools TruthValue,
cLMeshProfileAmsdu TruthValue,
cLMeshProfileBackgroundScan TruthValue,
cLMeshProfileCcnMode TruthValue,
cLMeshProfileUniversalAccess TruthValue,
cLMeshProfileEtherVlanTransparent TruthValue,
cLMeshProfileFullSectorDfs TruthValue,
cLMeshProfileIdsState TruthValue,
cLMeshProfileMulticastMode INTEGER,
cLMeshProfileRange Unsigned32,
cLMeshProfileSecurityMode INTEGER,
cLMeshProfileConvergenceMethod INTEGER,
cLMeshProfileLscOnlyAuthentication TruthValue,
cLMeshProfileBridgeGroupName SnmpAdminString,
cLMeshProfileBGNStrictmatch TruthValue,
cLMeshProfileEthernetBridging TruthValue,
cLMeshProfileBatteryState TruthValue,
cLMeshProfileAuthorizationMethod SnmpAdminString,
cLMeshProfileAuthenticationMethod SnmpAdminString,
cLMeshProfileDot11bgBhaulRateType INTEGER,
cLMeshProfileDot11bgBhaulRate INTEGER,
cLMeshProfileDot11bgBhaulRateDot11nMcsIndex Unsigned32,
cLMeshProfileDot11aBhaulRateType INTEGER,
cLMeshProfileDot11aBhaulRate INTEGER,
cLMeshProfileDot11aBhaulRateDot11nMcsIndex Unsigned32,
cLMeshProfileDot11aBhaulRateDot11acMcsIndex Unsigned32,
cLMeshProfileDot11aBhaulRateDot11acSpatialStream Unsigned32,
clMeshProfileRowStatus RowStatus,
cLMeshProfileDot11bgBhaulRateDot11axMcsIndex Unsigned32,
cLMeshProfileDot11bgBhaulRateDot11axSpatialStream Unsigned32,
cLMeshProfileDot11aBhaulRateDot11axMcsIndex Unsigned32,
cLMeshProfileDot11aBhaulRateDot11axSpatialStream Unsigned32
}
cLMeshProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies a Mesh Profile."
::= { clMeshProfileEntry 1 }
cLMeshProfileDescr OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a human-readable description
of the profile."
::= { clMeshProfileEntry 2 }
cLMeshProfileASTools OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if anti-stranding tools are
enabled."
DEFVAL { false }
::= { clMeshProfileEntry 3 }
cLMeshProfileAmsdu OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if aggregation of MSDU is
enabled."
DEFVAL { true }
::= { clMeshProfileEntry 4 }
cLMeshProfileBackgroundScan OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if background scanning is
enabled."
DEFVAL { false }
::= { clMeshProfileEntry 5 }
cLMeshProfileCcnMode OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if change channel
notification needs to be sent or not by
parent AP to all its children when parent
AP changes channel"
DEFVAL { false }
::= { clMeshProfileEntry 6 }
cLMeshProfileUniversalAccess OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if client can
connect to backhaul radio or not."
DEFVAL { false }
::= { clMeshProfileEntry 7 }
cLMeshProfileEtherVlanTransparent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the vlan transparent mode
status. Vlan transparent mode will allow all the
VLANs on secondary ethernet interface."
DEFVAL { true }
::= { clMeshProfileEntry 8 }
cLMeshProfileFullSectorDfs OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether DFS is enabled or
not in Mesh network."
DEFVAL { true }
::= { clMeshProfileEntry 9 }
cLMeshProfileIdsState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if Ids reporting is enabled or
not for Mesh APs."
DEFVAL { false }
::= { clMeshProfileEntry 10 }
cLMeshProfileMulticastMode OBJECT-TYPE
SYNTAX INTEGER {
modeRegular(1),
modeIn(2),
modeOut(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies multicast mode for ethernet
bridged clients."
DEFVAL { modeOut }
::= { clMeshProfileEntry 11 }
cLMeshProfileRange OBJECT-TYPE
SYNTAX Unsigned32
UNITS "feet"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the optimal distance in feet
between RAP and MAP for backhaul link without
degrading SNR value."
DEFVAL { 12000 }
::= { clMeshProfileEntry 12 }
cLMeshProfileSecurityMode OBJECT-TYPE
SYNTAX INTEGER {
eap(1),
psk(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies authentication mode of RAP and
MAP mesh nodes in controller.
none - no authentication is done.
psk - pre shared key. Keys provided during manufacturing
will be used for authentication of mesh node.
eap - extensible authentication protocol is used to
authenticate mesh node. A value of 'eap' indicates,
authentication can happen by local-auth in controller
or by RADIUS server configured in controller."
::= { clMeshProfileEntry 13 }
cLMeshProfileConvergenceMethod OBJECT-TYPE
SYNTAX INTEGER {
standard(1),
fast(2),
veryFast(3),
noiseTolerentFast(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies convergence method used by AP
during link failure."
::= { clMeshProfileEntry 14 }
cLMeshProfileLscOnlyAuthentication OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies status of
cLMeshProfileLscOnlyAuthentication"
DEFVAL { false }
::= { clMeshProfileEntry 15 }
cLMeshProfileBridgeGroupName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..10))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates bridge group name configured
for mesh APs."
::= { clMeshProfileEntry 16 }
cLMeshProfileBGNStrictmatch OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether an AP
operating in mesh mode needs to have
strict bridge group matching enabled
or not."
DEFVAL { false }
::= { clMeshProfileEntry 17 }
cLMeshProfileEthernetBridging OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether ethernet bridging is
enabled or not."
DEFVAL { false }
::= { clMeshProfileEntry 18 }
cLMeshProfileBatteryState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if battery state
will be updated by AP or not."
DEFVAL { true }
::= { clMeshProfileEntry 19 }
cLMeshProfileAuthorizationMethod OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies authorization method for
mesh APs."
::= { clMeshProfileEntry 20 }
cLMeshProfileAuthenticationMethod OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies authentication method for
mesh APs."
::= { clMeshProfileEntry 21 }
cLMeshProfileDot11bgBhaulRateType OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
dot11abg(2),
dot11nMcs(3),
dot11axMcs(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies mesh backhaul data rate type
for 802.11bg backhaul radio"
DEFVAL { auto }
::= { clMeshProfileEntry 22 }
cLMeshProfileDot11bgBhaulRate OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
mbps1(1000),
mbps2(2000),
mbps5point5(5500),
mbps11(11000),
mbps6(6000),
mbps9(9000),
mbps12(12000),
mbps18(18000),
mbps24(24000),
mbps36(36000),
mbps48(48000),
mbps54(54000)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11bg data rate for
Mesh backhaul tx traffic."
DEFVAL { auto }
::= { clMeshProfileEntry 23 }
cLMeshProfileDot11bgBhaulRateDot11nMcsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11n mcs index for
Mesh backhaul tx traffic with 802.11bg radio"
DEFVAL { 0 }
::= { clMeshProfileEntry 24 }
cLMeshProfileDot11aBhaulRateType OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
dot11abg(2),
dot11nMcs(3),
dot11acMcs(4),
dot11axMcs(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies mesh backhaul data rate type
for 802.11a backhaul radio."
DEFVAL { auto }
::= { clMeshProfileEntry 25 }
cLMeshProfileDot11aBhaulRate OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
mbps6(6000),
mbps9(9000),
mbps12(12000),
mbps18(18000),
mbps24(24000),
mbps36(36000),
mbps48(48000),
mbps54(54000)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11a data rate for
Mesh backhaul tx traffic."
DEFVAL { auto }
::= { clMeshProfileEntry 26 }
cLMeshProfileDot11aBhaulRateDot11nMcsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11n mcs index for
Mesh backhaul tx traffic with 802.11a radio."
DEFVAL { 0 }
::= { clMeshProfileEntry 27 }
cLMeshProfileDot11aBhaulRateDot11acMcsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11ac mcs index for
Mesh backhaul tx traffic with 802.11a radio."
DEFVAL { 0 }
::= { clMeshProfileEntry 28 }
cLMeshProfileDot11aBhaulRateDot11acSpatialStream OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11ac mcs spatial stream for
Mesh backhaul tx traffic with 802.11a radio."
DEFVAL { 1 }
::= { clMeshProfileEntry 29 }
clMeshProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the status column for this row and used
to create and delete specific instances of rows
in this table."
::= { clMeshProfileEntry 30 }
cLMeshProfileDot11bgBhaulRateDot11axMcsIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..11)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11ax mcs index for
Mesh backhaul tx traffic with 802.11bg radio."
DEFVAL { 0 }
::= { clMeshProfileEntry 31 }
cLMeshProfileDot11bgBhaulRateDot11axSpatialStream OBJECT-TYPE
SYNTAX Unsigned32 (1..4)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11ax mcs spatial stream for
Mesh backhaul tx traffic with 802.11bg radio."
DEFVAL { 1 }
::= { clMeshProfileEntry 32 }
cLMeshProfileDot11aBhaulRateDot11axMcsIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..11)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11ax mcs index for
Mesh backhaul tx traffic with 802.11a radio."
DEFVAL { 0 }
::= { clMeshProfileEntry 33 }
cLMeshProfileDot11aBhaulRateDot11axSpatialStream OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the 802.11ax mcs spatial stream for
Mesh backhaul tx traffic with 802.11a radio."
DEFVAL { 1 }
::= { clMeshProfileEntry 34 }
-- ********************************************************************
-- * Mesh Network global configuration
-- ********************************************************************
clMeshNodeRange OBJECT-TYPE
SYNTAX Unsigned32 (150..132000)
UNITS "feet"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the optimal distance in feet
between RAP and MAP for backhaul link without
degrading SNR value."
DEFVAL { 12000 }
::= { ciscoLwappMeshGlobalConfig 1 }
clMeshBackhaulClientAccess OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether client access needs to
be allowed on backhaul link. If AP has two radios,802.11a
and 802.11bg, then radio which is used as backhaul link
does not have client access.If AP has only one radio then
same radio is used for backhaul and client access.
A value of 'true' indicates client access is present on
backhaul link.
A value of 'false' indicates backhaul client access
disabled."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 2 }
clMeshMacFilterList OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether mac filtering needs to
be enabled on controller for joining mesh AP.
A value of 'true' indicates that mesh mac filter is enabled.
A value of 'false' indicates that mesh node can join
controller even if mesh node MAC address is not
in MAC filter list."
DEFVAL { true }
::= { ciscoLwappMeshGlobalConfig 3 }
clMeshMeshNodeAuthFailureThreshold OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
UNITS "failures"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the authorization failure
threshold value. When the number of failures exceeds
this value then 'ciscoLwappMeshAuthFailure'
notification is raised."
DEFVAL { 5 }
::= { ciscoLwappMeshGlobalConfig 4 }
clMeshMeshChildAssociationFailuresThreshold OBJECT-TYPE
SYNTAX Unsigned32 (10..30)
UNITS "failures"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the number of failed association
to controller occurred through a parent mesh node.
When this values exceeds then
'ciscoLwappMeshChildExcludedParent' notification is
raised."
DEFVAL { 10 }
::= { ciscoLwappMeshGlobalConfig 5 }
clMeshMeshChildExcludedParentInterval OBJECT-TYPE
SYNTAX TimeInterval (18000..96000)
UNITS "hundredths-seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the time interval during which
a child mesh node will exclude a parent mesh node.
During this interval child will not try to associate
the controller through the parent mesh node."
DEFVAL { 48000 }
::= { ciscoLwappMeshGlobalConfig 6 }
clMeshSNRThresholdAbate OBJECT-TYPE
SYNTAX Unsigned32 (3..50)
UNITS "db"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the abate threshold value of
SNR. This threshold value is use to determine if the
SNR value seen by the child mesh node has reached
acceptable level and is use to trigger the
'ciscoLwappMeshAbateSNR' notification."
DEFVAL { 16 }
::= { ciscoLwappMeshGlobalConfig 7 }
clMeshSNRThresholdOnset OBJECT-TYPE
SYNTAX Unsigned32 (3..50)
UNITS "db"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the onset threshold value of
SNR. This threshold value is use to determine if the
SNR value seen by the child mesh node has reached
below unacceptable level and is use to trigger the
'ciscoLwappMeshOnsetSNR' notification."
DEFVAL { 12 }
::= { ciscoLwappMeshGlobalConfig 8 }
clMeshSNRCheckTimeInterval OBJECT-TYPE
SYNTAX TimeInterval (18000..96000)
UNITS "hundredths-seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the time interval after which
SNR value is checked by child mesh node."
DEFVAL { 18000 }
::= { ciscoLwappMeshGlobalConfig 9 }
clMeshExcessiveParentChangeThreshold OBJECT-TYPE
SYNTAX Unsigned32 (1..20)
UNITS "occcurences"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the threshold for the number
of times a child mesh node changes its parent. If number
of parent change exceeds this value with in the time
interval defined by object
'clMeshExcessiveParentChangeInterval' then
the 'ciscoLwappMeshExcessiveParentChange' notification
is raised."
DEFVAL { 5 }
::= { ciscoLwappMeshGlobalConfig 10 }
clMeshExcessiveParentChangeInterval OBJECT-TYPE
SYNTAX TimeInterval (180000..360000)
UNITS "hundredths-seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the time interval during which
number of times a child mesh node changes its parent
change is counted.
If number of parent change exceeds the value defined by
the object 'clMeshExcessiveParentChangeThreshold' with in
this time interval then the
'ciscoLwappMeshExcessiveParentChange' notification
is raised."
DEFVAL { 360000 }
::= { ciscoLwappMeshGlobalConfig 11 }
clMeshBackgroundScan OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether mesh AP can
scans its neighbors on different channel other than
only its current channel on backhaul link.
A value of 'true' indicates mesh background scan enabled.
A value of 'false' indicates mesh background scan disabled."
DEFVAL { true }
::= { ciscoLwappMeshGlobalConfig 12 }
clMeshAuthenticationMode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
eap(2),
psk(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies authentication mode of RAP and
MAP mesh nodes in controller.
none - no authentication is done.
psk - pre shared key. Keys provided during manufacturing
will be used for authentication of mesh node.
eap - extensible authentication protocol is used to
authenticate mesh node. A value of 'eap' indicates,
authentication can happen by local-auth in
controller or by RADIUS server configured in
controller."
DEFVAL { psk }
::= { ciscoLwappMeshGlobalConfig 13 }
clMeshExcessiveHopCountThreshold OBJECT-TYPE
SYNTAX Unsigned32 (1..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies threshold number of hops from the
MAP node to the RAP. Crossing this value will raise the
'ciscoLwappMeshExcessiveHopCount' notification."
DEFVAL { 4 }
::= { ciscoLwappMeshGlobalConfig 14 }
clMeshExcessiveRapChildThreshold OBJECT-TYPE
SYNTAX Unsigned32 (1..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies threshold number of children MAPs
attached to a parent RAP. Crossing this value will raise the
'ciscoLwappMeshExcessiveChildren' notification."
DEFVAL { 20 }
::= { ciscoLwappMeshGlobalConfig 15 }
clMeshExcessiveMapChildThreshold OBJECT-TYPE
SYNTAX Unsigned32 (1..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies threshold number of children MAPs
attached to a parent MAP. Crossing this value will raise the
'ciscoLwappMeshExcessiveChildren' notification."
DEFVAL { 10 }
::= { ciscoLwappMeshGlobalConfig 16 }
clMeshHighSNRThresholdAbate OBJECT-TYPE
SYNTAX Unsigned32 (50..80)
UNITS "db"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the abate threshold value of
SNR. This threshold value is used to determine if the
SNR value seen by the child mesh node has reached
below this level and is use to trigger the
'ciscoLwappMeshAbateHighSNR' notification."
DEFVAL { 60 }
::= { ciscoLwappMeshGlobalConfig 17 }
clMeshHighSNRThresholdOnset OBJECT-TYPE
SYNTAX Unsigned32 (50..80)
UNITS "db"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the onset threshold value of
SNR. This threshold value is use to determine if the
SNR value seen by the child mesh node has reached
above this level and is use to trigger the
'ciscoLwappMeshOnsetHighSNR' notification."
DEFVAL { 56 }
::= { ciscoLwappMeshGlobalConfig 18 }
clMeshPublicSafetyBackhaulGlobal OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies user to enable 4.9Ghz as
backhaul link which is considered to be public safety
band limited to some service providers.
A value of 'true' indicates that 4.9 Ghz can be used
on backhaul link by selecting channel on the 802.11a
backhaul radio.
A value of 'false' indicates that 4.9 Ghz cannot be used
on backhaul link by selecting channel on the 802.11a
backhaul radio.
This setting applies at the controller level. The
prior per AP setting clMeshNodePublicSafetyBackhaul
is deprecated as a result."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 19 }
clMeshisAMSDUEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Aggreation Service Data Unit at
MAC layer (AMSDU) status.
A value of 'true' indicates that AMSDU is enabled.
A value of 'false' indicates that AMSDU is disabled."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 20 }
clMeshIsIdsEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Rogue and Signature Detection status.
A value of 'true' indicates that IDS is enabled.
A value of 'false' indicates that IDS is disabled."
DEFVAL { true }
::= { ciscoLwappMeshGlobalConfig 21 }
clMeshIsDCAChannelsEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Dynamic Channel Assignment status.
A value of 'true' indicates DCA feature for AP1524SB is
enabled.
A value of 'false' indicates DCA feature for AP1524SB is
disabled.
This is not implies for non-1524SB APs. Error will return
if it is set for non-1524SB APs."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 22 }
clMeshIsExtendedUAEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Universal Client Access status.
A value of 'true' indicates that ExtendedUA feature is
enabled.
A value of 'false' indicates that ExtendedUA feature is
disabled."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 23 }
clMeshIsBDomainChannelsEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the UNI1 Channel status.
A value of 'true' indicates that B domain channels for
outdoor mesh AP can be alllowed.
A value of 'false' indicates that B domain channels for
outdoor mesh AP cannot be allowed.
This doesnot implies for non-outdoor mesh APs."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 24 }
clMeshPskKeyProvisionEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the PSK key provisioning status.
A value of 'true' indicates that PSK Key provisioning
is enabled.
A value of 'false' indicates that PSK Key provisioning
is disabled."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 25 }
clMeshPskKeyWindowEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the PSK key provisioning window status.
A value of 'true' indicates that PSK Key provisioning window
is enabled.
A value of 'false' indicates that PSK Key provisioning window
is disabled."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 26 }
clMeshEthenetBridgingVlanTransparent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the vlan transparent mode status.
Vlan transparent mode will allow all the VLANs on secondary
ethernet interface
A value of 'true' indicates that Vlan Transparent mode
is enabled.
A value of 'false' indicates that Vlan Transparent mode
is disabled."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 27 }
clMeshRAPDownlinkBackhaul OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
slot0(1),
slot1(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects specifies the global config of Mesh backhaul
slot configured on the WLC.
And also used to configure/change the backhaul slot of RAPs
joined to the WLC.
slot0 - downlink backhaul access for slot0 is enabled.
slot1 - downlink backhaul access for slot1 is enabled."
::= { ciscoLwappMeshGlobalConfig 28 }
clMeshPskInUseKeyIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..5)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the psk key index which
is currently in use out of the configured PSK keys
for Mesh Access Point Authorization"
DEFVAL { 1 }
::= { ciscoLwappMeshGlobalConfig 29 }
clMeshEthBridgingAllowBpdu OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether we should allow
BPDU packets in the mesh network when ethernet
bridging is enabled.
A value of 'true' indicates BPDU packets are allowed
in mesh network.
A value of 'false' indicates BPDU packets are dropped
in mesh network."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 30 }
clMeshIsRapChannelSyncEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether mesh RAP channels list sync
is allowed or not with mobility peers.
A value of 'true' indicates RAP channels sync is allowed
with mobility peers.
A value of 'false' indicates RAP channels sync is not allowed
with mobility peers."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 31 }
clMeshIsBackhaulRrmEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether Radio Resource Management(RRM)
is enabled or not in mesh backhaul radio. In Enabled state, RRM
measurements are enabled for Ethernet connected Root mode Mesh
APs which does not have any child Mesh Aps connected.
A value of 'true' indicates RRM is enabed in
Mesh backhaul radio.
A value of 'false' indicates RRM is disabled in
Mesh backhaul radio."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 32 }
clMeshIsCacEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether CAC functionality is enabled on
mesh backhaul radio
A value of 'true' indicates CAC is enabed in Mesh backhaul radio.
A value of 'false' indicates CAC is disabled in Mesh backhaul radio."
DEFVAL { false }
::= { ciscoLwappMeshGlobalConfig 33 }
-- ********************************************************************
-- * NEIGHBOR STATUS
-- ********************************************************************
clMeshNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClMeshNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents information about neighbors
of any mesh node. Neighbor AP can be on same or
different mesh sector. Any mesh node is neighbor of a
mesh node, if it can detect 802.11 signals on any
channels. Child or parent mesh node also considers as
neighbors."
::= { ciscoLwappMeshNeighborsStatus 1 }
clMeshNeighborEntry OBJECT-TYPE
SYNTAX ClMeshNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An (conceptual) entry in this table is created when
mesh node detects neighbor mesh nodes.
Entries are removed when the mesh node does not detect
AP as neighbor."
INDEX {
cLApSysMacAddress,
clMeshNeighborMacAddress
}
::= { clMeshNeighborTable 1 }
ClMeshNeighborEntry ::= SEQUENCE {
clMeshNeighborMacAddress MacAddress,
clMeshNeighborType BITS,
clMeshNeighborLinkSnr Integer32,
clMeshNeighborChannel CLDot11Channel,
clMeshNeighborUpdate TimeStamp
}
clMeshNeighborMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents MAC address of neighbor
mesh node."
::= { clMeshNeighborEntry 1 }
clMeshNeighborType OBJECT-TYPE
SYNTAX BITS {
parent(0),
neighbor(1),
excluded(2),
child(3),
beacon(4),
default(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents type of neighbor mesh node.
parent - Neighbor mesh node is a parent mesh node
of this mesh node.
neighbor - Its a neighbor mesh node. It can be on
same or different mesh-sector.
excluded - Neighbor mesh node is excluded by this
mesh node.
child - Neighbor mesh node is child of this mesh node.
beacon - Neighbor mesh node found by passive scanning.
Default - Neighbor mesh node connected using a mismatched
bridge group name"
::= { clMeshNeighborEntry 2 }
clMeshNeighborLinkSnr OBJECT-TYPE
SYNTAX Integer32
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the SNR value seen by this mesh
node from neighbor mesh node."
::= { clMeshNeighborEntry 3 }
clMeshNeighborChannel OBJECT-TYPE
SYNTAX CLDot11Channel
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the channel on which neighbor
mesh node is operating."
::= { clMeshNeighborEntry 4 }
clMeshNeighborUpdate OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents when the neighbor table was last
updated. This value is represented as a instance of
sysUp time."
::= { clMeshNeighborEntry 5 }
-- ********************************************************************
-- * MESH ATF STATS
-- ********************************************************************
clMeshAtfStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClMeshAtfStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents ATF mesh stats for all the
RAPs/PMAPs having one or more child mesh nodes."
::= { ciscoLwappMeshNeighborsStatus 2 }
clMeshAtfStatsEntry OBJECT-TYPE
SYNTAX ClMeshAtfStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An (conceptual) entry in this table is created when
mesh node detects neighbor mesh nodes having the ATF enabled.
Entries are removed when the mesh node does not detect
AP as neighbor."
INDEX {
cLApSysMacAddress,
clMeshNeighborMacAddress
}
::= { clMeshAtfStatsTable 1 }
ClMeshAtfStatsEntry ::= SEQUENCE {
clMeshAtfAirtimeUsedInstantaneous Unsigned32,
clMeshAtfAirtimeUsedCumulative Unsigned64,
clMeshAtfFramesSentInstantaneous Unsigned32,
clMeshAtfFramesSentCumulative Unsigned64,
clMeshAtfFramesDroppedInstantaneous Unsigned32,
clMeshAtfFramesDroppedCumulative Unsigned64
}
clMeshAtfAirtimeUsedInstantaneous OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the instantaneous air time used."
DEFVAL { 0 }
::= { clMeshAtfStatsEntry 1 }
clMeshAtfAirtimeUsedCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the cumulative air time used."
DEFVAL { 0 }
::= { clMeshAtfStatsEntry 2 }
clMeshAtfFramesSentInstantaneous OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents number of bytes sent to its
neighbor mesh nodes."
DEFVAL { 0 }
::= { clMeshAtfStatsEntry 3 }
clMeshAtfFramesSentCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents number of bytes sent cumulative to
its neighbor mesh nodes."
DEFVAL { 0 }
::= { clMeshAtfStatsEntry 4 }
clMeshAtfFramesDroppedInstantaneous OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents number of frames dropped
instantaneous to its neighbor mesh nodes(parent/child)."
DEFVAL { 0 }
::= { clMeshAtfStatsEntry 5 }
clMeshAtfFramesDroppedCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents number of frames dropped cumulative to
its neighbor mesh nodes."
DEFVAL { 0 }
::= { clMeshAtfStatsEntry 6 }
-- ********************************************************************
-- * GPS related information
-- ********************************************************************
clMeshGpsInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF ClMeshGpsInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents information about location and
velocity parameters received from the GPS module on the
LWAPP Access Points that have joined the controller
as part of a mesh network."
::= { ciscoLwappMeshGpsObjects 1 }
clMeshGpsInfoEntry OBJECT-TYPE
SYNTAX ClMeshGpsInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a conceptual row in this table.
An entry is created when MAP joins the controller.
The entry is removed when the mesh node lose their
association with the controller due to loss of
communication with controller or when a mesh node
is reset."
INDEX { cLApSysMacAddress }
::= { clMeshGpsInfoTable 1 }
ClMeshGpsInfoEntry ::= SEQUENCE {
clMeshGpsLocationPresent TruthValue,
clMeshGpsLocationValid TruthValue,
clMeshGpsLatitude SnmpAdminString,
clMeshGpsLongitude SnmpAdminString,
clMeshGpsAltitude SnmpAdminString,
clMeshGpsCollectionTime TimeStamp
}
clMeshGpsLocationPresent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates whether the access point
has the GPS module installed or not."
::= { clMeshGpsInfoEntry 1 }
clMeshGpsLocationValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates whether the location
information is valid or not."
::= { clMeshGpsInfoEntry 2 }
clMeshGpsLatitude OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents latitude information
in the GPS data received."
::= { clMeshGpsInfoEntry 3 }
clMeshGpsLongitude OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents longitude information
in the GPS data received."
::= { clMeshGpsInfoEntry 4 }
clMeshGpsAltitude OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents altitude information
in the GPS data received."
::= { clMeshGpsInfoEntry 5 }
clMeshGpsCollectionTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents the time when GPS
data was collected."
::= { clMeshGpsInfoEntry 6 }
-- ********************************************************************
-- * Notification control flags
-- ********************************************************************
clMeshAuthFailureNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity
generates the 'ciscoLwappMeshAuthFailure'
notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 1 }
clMeshChildExcludedParentNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity
generates the 'ciscoLwappMeshChildExcludedParent'
notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 2 }
clMeshParentChangeNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity generates
the 'ciscoLwappMeshParentChange' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 3 }
clMeshChildMovedNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity generates the
'ciscoLwappMeshChildMoved' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 4 }
clMeshExcessiveParentChangeNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity generates the
'ciscoLwappMeshExcessiveParentChange' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 5 }
clMeshPoorSNRNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity generates the
'ciscoLwappMeshOnsetSNR' and
'ciscoLwappMeshAbateSNR' notifications.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 6 }
clMeshConsoleLoginNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity generates
the 'ciscoLwappMeshConsoleLogin' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 7 }
clMeshDefaultBridgeGroupNameNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP generates the
'ciscoLwappMeshDefaultBridgeGroupName' notification.
A value of 'true' indicates this notification will be
generated.
A value of 'false' indicates this notification will
not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 8 }
clMeshExcessiveHopCountNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity generates
the 'ciscoLwappMeshExcessiveHopCount' notification.
A value of 'true' indicates this notification will
be generated.
A value of 'false' indicates this notification will
not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 9 }
clMeshExcessiveChildrenNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity generates
the 'ciscoLwappMeshExcessiveChildren' notification.
A value of 'true' indicates this notification
will be generated.
A value of 'false' indicates this notification
will not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 10 }
clMeshHighSNRNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the SNMP entity
generates the 'ciscoLwappMeshOnsetHighSNR' and
'ciscoLwappMeshAbateHighSNR' notifications.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
not be generated."
DEFVAL { true }
::= { ciscoLwappMeshNotifControlConfig 11 }
-- ********************************************************************
-- * NOTIFICATION objects
-- ********************************************************************
clMeshNodeMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the MAC address
of a LWAPP AP."
::= { ciscoLwappMeshMIBNotifObjects 1 }
clMeshAuthFailureReason OBJECT-TYPE
SYNTAX INTEGER {
notInMacFilterList(1),
securityFailure(2)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the failure reason when
a mesh node failed to authenticate through a
controller to an Authentication Server.
notInMacFilterList - MAC address of a mesh node
is not configured in MAC filter list.
securityFailure - Authentication server sent
rejection for the mesh node."
::= { ciscoLwappMeshMIBNotifObjects 2 }
clMeshPreviousParentMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the MAC address
of previous parent Mesh Node."
::= { ciscoLwappMeshMIBNotifObjects 3 }
clMeshConsoleLoginStatus OBJECT-TYPE
SYNTAX INTEGER {
success(1),
failure(2)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the status of console login
at MAP mesh node."
::= { ciscoLwappMeshMIBNotifObjects 4 }
clMeshNodePrevTemperatureState OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the previous temperature
state of the Mesh AP."
::= { ciscoLwappMeshMIBNotifObjects 5 }
clMeshNodeNewTemperatureState OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the new temperature
state of the Mesh AP."
::= { ciscoLwappMeshMIBNotifObjects 6 }
-- ********************************************************************
-- * NOTIFICATION TYPE objects
-- ********************************************************************
ciscoLwappMeshAuthFailure NOTIFICATION-TYPE
OBJECTS {
clMeshNodeMacAddress,
clMeshAuthFailureReason
}
STATUS current
DESCRIPTION
"This notification is generated by agent when
number of failures exceeds threshold defined by object
'clMeshMeshNodeAuthFailureThreshold'. Object
'clMeshAuthFailureNotifEnabled' controls the
generation of this notification.
A mesh node can fail to authorize if the MAC address
of mesh node is not in the MAC filter list or security
failure by authentication server. Reason is specified by
'clMeshAuthFailureReason'."
::= { ciscoLwappMeshMIBNotifs 1 }
ciscoLwappMeshChildExcludedParent NOTIFICATION-TYPE
OBJECTS {
clMeshNodeParentMacAddress,
clMeshPreviousParentMacAddress,
cLApName
}
STATUS current
DESCRIPTION
"This notification generated by agent when child
mesh node exceeds threshold limit of number of
discovery response timeouts defined by object
'clMeshMeshChildAssociationFailuresThreshold'. The
child mesh node will not try to associate excluded
parent mesh node for the interval defined by object
'clMeshMeshChildExcludedParentInterval'.
The child mesh node will remember the excluded parent
MAC address and when it joins the network it will
inform the controller.
'cLApName' specifies child mesh node name. Child MAC
address is sent as part of index. Object
'clMeshChildExcludedParentNotifEnabled' controls the
generation of this notification."
::= { ciscoLwappMeshMIBNotifs 2 }
ciscoLwappMeshParentChange NOTIFICATION-TYPE
OBJECTS {
clMeshNodeParentMacAddress,
clMeshPreviousParentMacAddress,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when a child
mesh node changes its parent. Child mesh node will
remember its previous parent and when it joins the
network it will inform controller about change
of its parent. 'cLApName' specifies child mesh node
name. Child mesh node MAC address is sent as part of
index. Object 'clMeshParentChangeNotifEnabled' controls
the generation of this notification."
::= { ciscoLwappMeshMIBNotifs 3 }
ciscoLwappMeshChildMoved NOTIFICATION-TYPE
OBJECTS {
clMeshNeighborType,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when a parent
mesh node loses connection with its child mesh node.
'cLApName' specifies parent mesh node name. Parent and
child MAC address are sent as part of index. Object
'clMeshChildMovedNotifEnabled' controls
the generation of this notification."
::= { ciscoLwappMeshMIBNotifs 4 }
ciscoLwappMeshExcessiveParentChange NOTIFICATION-TYPE
OBJECTS {
clMeshNeighborType,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when a child
mesh node changes its parent frequently. Each
mesh node keeps count of number of parent changes
in fixed time. If it exceeds the threshold defined
by 'clMeshExcessiveParentChangeThreshold' then child
mesh node informs the controller. 'cLApName' specifies
child mesh node name. Child and Parent MAC address are
sent as part of index. Object
'clMeshExcessiveParentChangeNotifEnabled' controls
the generation of this notification."
::= { ciscoLwappMeshMIBNotifs 5 }
ciscoLwappMeshOnsetSNR NOTIFICATION-TYPE
OBJECTS {
clMeshNeighborLinkSnr,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when a child
mesh node detects lower SNR on backhaul link then
defined by object 'clMeshSNRThresholdOnset'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'ciscoLwappMeshAbateSNR' notification will be sent
to clear this notification. 'cLApName' specifies
child mesh node name. Child and parent MAC address
are sent as part of index. Object
'clMeshPoorSNRNotifEnabled' controls the generation
of this notification."
::= { ciscoLwappMeshMIBNotifs 6 }
ciscoLwappMeshAbateSNR NOTIFICATION-TYPE
OBJECTS {
clMeshNeighborLinkSnr,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent to clear
'ciscoLwappMeshOnsetSNR' notification when child mesh
node detects SNR on backhaul link is higher then
the object defined by 'clMeshSNRThresholdAbate'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'cLApName' specifies child mesh node name.
Child and parent MAC address are sent as part of index.
Object 'clMeshPoorSNRNotifEnabled' controls the
generation of this notification."
::= { ciscoLwappMeshMIBNotifs 7 }
ciscoLwappMeshConsoleLogin NOTIFICATION-TYPE
OBJECTS {
clMeshNodeMacAddress,
clMeshConsoleLoginStatus,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when login on
MAP console is successful or failure after three
attempts. 'cLApName' specifies mesh node name.
Object 'clMeshConsoleLoginNotifEnabled' controls the
generation of this notification."
::= { ciscoLwappMeshMIBNotifs 8 }
ciscoLwappMeshDefaultBridgeGroupName NOTIFICATION-TYPE
OBJECTS {
cLApName,
clMeshNodeParentMacAddress
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when MAP
mesh node joins parent using 'default' bridge
group name. The child node mac address is sent as the
index of cLApName."
::= { ciscoLwappMeshMIBNotifs 9 }
ciscoLwappMeshExcessiveHopCount NOTIFICATION-TYPE
OBJECTS {
cLApName,
clMeshNodeHops
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when the
number of hops from the MAP node to the RAP exceeds the
threshold defined by 'clMeshExcessiveHopCountThreshold'.
The MAP MAC address is sent as part of the index. These
alarms are raised once in three minutes, the periodicity
of AP sending the statistics to WLC."
::= { ciscoLwappMeshMIBNotifs 10 }
ciscoLwappMeshExcessiveChildren NOTIFICATION-TYPE
OBJECTS {
cLApName,
clMeshNodeRole,
clMeshNodeChildCount
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when the
child count exceeds clMeshExcessiveRapChildThreshold
for a RAP and clMeshExcessiveMapChildThreshold for a MAP.
The node MAC address is sent as a part of the index.
These alarms are raised once in three minutes, the
periodicity of AP sending the statistics to WLC."
::= { ciscoLwappMeshMIBNotifs 11 }
ciscoLwappMeshOnsetHighSNR NOTIFICATION-TYPE
OBJECTS {
clMeshNeighborLinkSnr,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when child
mesh node detects higher SNR on backhaul link then
defined by object 'clMeshHighSNRThresholdOnset'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'ciscoLwappMeshAbateHighSNR' notification will be sent
to clear this notification. 'cLApName' specifies
child mesh node name. Child and parent MAC address
are sent as part of index. Object
'clMeshHighSNRNotifEnabled' controls the generation
of this notification. These alarms are raised once in three
minutes, the periodicity of AP sending the statistics to
WLC."
::= { ciscoLwappMeshMIBNotifs 12 }
ciscoLwappMeshAbateHighSNR NOTIFICATION-TYPE
OBJECTS {
clMeshNeighborLinkSnr,
cLApName
}
STATUS current
DESCRIPTION
"This notification is generated by the agent to clear
'ciscoLwappMeshOnsetSNR' notification when child mesh
node detects SNR on backhaul link, which is lower than
the object defined by 'clMeshHighSNRThresholdAbate'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'clMeshNeighborLinkSnr' represents the SNR value seen by this
mesh node from neighbor mesh node.
'cLApName' specifies child mesh node name.
Child and parent MAC address are sent as part of index.
Object 'clMeshHighSNRNotifEnabled' controls the
generation of this notification."
::= { ciscoLwappMeshMIBNotifs 13 }
ciscoLwappMeshTemperatureStateChange NOTIFICATION-TYPE
OBJECTS {
clMeshNodeMacAddress,
clMeshNodePrevTemperatureState,
clMeshNodeNewTemperatureState
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when
there is a change occurred in the temperature state
of the Mesh AP."
::= { ciscoLwappMeshMIBNotifs 14 }
ciscoLwappMeshPskKeyAuthFailure NOTIFICATION-TYPE
OBJECTS {
clMeshNodeParentMacAddress,
clMeshNodeMacAddress
}
STATUS current
DESCRIPTION
"This notification is generated by the agent when
mesh node fail to join to controller with PSK Key
present on the Mesh AP."
::= { ciscoLwappMeshMIBNotifs 15 }
-- ********************************************************************
-- * Compliance statements
-- ********************************************************************
ciscoLwappMeshMIBCompliances OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBConform 1 }
ciscoLwappMeshMIBGroups OBJECT IDENTIFIER
::= { ciscoLwappMeshMIBConform 2 }
ciscoLwappMeshMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappMeshMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappMeshConfigGroup,
ciscoLwappMeshNeighborStatusGroup,
ciscoLwappMeshNotifControlGroup,
ciscoLwappMeshNotifObjsGroup,
ciscoLwappMeshNotifsGroup
}
::= { ciscoLwappMeshMIBCompliances 1 }
ciscoLwappMeshMIBComplianceR01 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappMeshMIB module.This deprecates
ciscoLwappMeshMIBCompliance"
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappMeshNeighborStatusGroup,
ciscoLwappMeshNotifControlGroup,
ciscoLwappMeshNotifObjsGroup,
ciscoLwappMeshNotifsGroup,
ciscoLwappMeshConfigGroupSup1,
ciscoLwappMeshNotifControlGroupSup1,
ciscoLwappMeshNotifsGroupSup1
}
::= { ciscoLwappMeshMIBCompliances 2 }
ciscoLwappMeshMIBComplianceR02 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappMeshMIB module.This deprecates
ciscoLwappMeshMIBComplianceR01"
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappMeshNeighborStatusGroup,
ciscoLwappMeshNotifControlGroup,
ciscoLwappMeshNotifObjsGroup,
ciscoLwappMeshNotifsGroup,
ciscoLwappMeshConfigGroupSup2,
ciscoLwappMeshNotifControlGroupSup1,
ciscoLwappMeshNotifsGroupSup1,
ciscoLwappMeshConfigGroupRev3,
ciscoLwappMeshAtfStatusGroup,
ciscoLwappMeshPskConfigGroup
}
::= { ciscoLwappMeshMIBCompliances 3 }
ciscoLwappMeshMIBComplianceR03 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappMeshMIB module.This deprecates
ciscoLwappMeshMIBComplianceR02"
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappMeshNeighborStatusGroup,
ciscoLwappMeshNotifControlGroup,
ciscoLwappMeshNotifObjsGroup,
ciscoLwappMeshNotifsGroup,
ciscoLwappMeshConfigGroupSup2,
ciscoLwappMeshNotifControlGroupSup1,
ciscoLwappMeshNotifsGroupSup1,
ciscoLwappMeshConfigGroupRev3,
ciscoLwappMeshAtfStatusGroup,
ciscoLwappMeshPskConfigGroup,
ciscoLwappMeshProfileConfigGroup
}
::= { ciscoLwappMeshMIBCompliances 4 }
ciscoLwappMeshMIBComplianceR04 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappMeshMIB module.This deprecates
ciscoLwappMeshMIBComplianceR03"
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappMeshNeighborStatusGroup,
ciscoLwappMeshNotifControlGroup,
ciscoLwappMeshNotifObjsGroup,
ciscoLwappMeshNotifsGroup,
ciscoLwappMeshConfigGroupSup2,
ciscoLwappMeshNotifControlGroupSup1,
ciscoLwappMeshNotifsGroupSup1,
ciscoLwappMeshConfigGroupRev3,
ciscoLwappMeshAtfStatusGroup,
ciscoLwappMeshPskConfigGroup,
ciscoLwappMeshProfileConfigGroup,
ciscoLwappMeshProfileConfigGroupRev1
}
::= { ciscoLwappMeshMIBCompliances 5 }
-- ********************************************************************
-- * Units of conformance
-- ********************************************************************
ciscoLwappMeshConfigGroup OBJECT-GROUP
OBJECTS {
clMeshNodeRole,
clMeshNodeGroupName,
clMeshNodeBackhaul,
clMeshNodeBackhaulDataRate,
clMeshNodeEthernetBridge,
clMeshNodeEthernetLinkStatus,
clMeshNodePublicSafetyBackhaul,
clMeshNodeParentMacAddress,
clMeshNodeHeaterStatus,
clMeshNodeInternalTemp,
clMeshNodeType,
clMeshNodeHops,
clMeshNodeRange,
clMeshBackhaulClientAccess,
clMeshMacFilterList,
clMeshMeshNodeAuthFailureThreshold,
clMeshMeshChildAssociationFailuresThreshold,
clMeshMeshChildExcludedParentInterval,
clMeshSNRThresholdAbate,
clMeshSNRThresholdOnset,
clMeshSNRCheckTimeInterval,
clMeshExcessiveParentChangeThreshold,
clMeshExcessiveParentChangeInterval,
clMeshBackgroundScan,
clMeshAuthenticationMode
}
STATUS deprecated
DESCRIPTION
"This collection of objects represent the
global and mesh node specific configuration
and monitor parameters."
::= { ciscoLwappMeshMIBGroups 1 }
ciscoLwappMeshNeighborStatusGroup OBJECT-GROUP
OBJECTS {
clMeshNeighborType,
clMeshNeighborLinkSnr,
clMeshNeighborChannel,
clMeshNeighborUpdate
}
STATUS current
DESCRIPTION
"This collection of objects represent the
neighbor status of any mesh node."
::= { ciscoLwappMeshMIBGroups 2 }
ciscoLwappMeshNotifControlGroup OBJECT-GROUP
OBJECTS {
clMeshAuthFailureNotifEnabled,
clMeshChildExcludedParentNotifEnabled,
clMeshParentChangeNotifEnabled,
clMeshChildMovedNotifEnabled,
clMeshExcessiveParentChangeNotifEnabled,
clMeshPoorSNRNotifEnabled,
clMeshConsoleLoginNotifEnabled
}
STATUS current
DESCRIPTION
"This collection of objects represent the flags
to control the generation of notification."
::= { ciscoLwappMeshMIBGroups 3 }
ciscoLwappMeshNotifObjsGroup OBJECT-GROUP
OBJECTS {
clMeshNodeMacAddress,
clMeshAuthFailureReason,
clMeshPreviousParentMacAddress,
clMeshConsoleLoginStatus,
clMeshNodePrevTemperatureState,
clMeshNodeNewTemperatureState
}
STATUS current
DESCRIPTION
"This collection of objects represent the information
carried by the mesh network related notifications sent
by the agent to a network management station."
::= { ciscoLwappMeshMIBGroups 4 }
ciscoLwappMeshNotifsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
ciscoLwappMeshAuthFailure,
ciscoLwappMeshChildExcludedParent,
ciscoLwappMeshParentChange,
ciscoLwappMeshChildMoved,
ciscoLwappMeshExcessiveParentChange,
ciscoLwappMeshOnsetSNR,
ciscoLwappMeshAbateSNR,
ciscoLwappMeshConsoleLogin
}
STATUS current
DESCRIPTION
"This collection of objects represent the mesh network
related notifications sent by the agent to a network
management station."
::= { ciscoLwappMeshMIBGroups 5 }
ciscoLwappMeshConfigGroupSup1 OBJECT-GROUP
OBJECTS {
clMeshNodeRole,
clMeshNodeGroupName,
clMeshNodeBackhaul,
clMeshNodeBackhaulDataRate,
clMeshNodeEthernetBridge,
clMeshNodeEthernetLinkStatus,
clMeshNodeParentMacAddress,
clMeshNodeHeaterStatus,
clMeshNodeInternalTemp,
clMeshNodeType,
clMeshNodeHops,
clMeshNodeChildCount,
clMeshNodeBackhaulRadio,
clMeshNodeRange,
clMeshBackhaulClientAccess,
clMeshMacFilterList,
clMeshMeshNodeAuthFailureThreshold,
clMeshMeshChildAssociationFailuresThreshold,
clMeshMeshChildExcludedParentInterval,
clMeshSNRThresholdAbate,
clMeshSNRThresholdOnset,
clMeshHighSNRThresholdAbate,
clMeshHighSNRThresholdOnset,
clMeshSNRCheckTimeInterval,
clMeshExcessiveParentChangeThreshold,
clMeshExcessiveParentChangeInterval,
clMeshBackgroundScan,
clMeshAuthenticationMode,
clMeshExcessiveHopCountThreshold,
clMeshExcessiveRapChildThreshold,
clMeshExcessiveMapChildThreshold,
clMeshPublicSafetyBackhaulGlobal,
clMeshisAMSDUEnable,
clMeshIsIdsEnable,
clMeshIsDCAChannelsEnable,
clMeshIsExtendedUAEnable
}
STATUS deprecated
DESCRIPTION
"This collection of objects represent the
global and mesh node specific configuration
and monitor parameters."
::= { ciscoLwappMeshMIBGroups 6 }
ciscoLwappMeshNotifControlGroupSup1 OBJECT-GROUP
OBJECTS {
clMeshHighSNRNotifEnabled,
clMeshDefaultBridgeGroupNameNotifEnabled,
clMeshExcessiveHopCountNotifEnabled,
clMeshExcessiveChildrenNotifEnabled
}
STATUS current
DESCRIPTION
"This collection of objects represent the flags
to control the generation of notification.This
deprecates ciscoLwappMeshNotifControlGroup."
::= { ciscoLwappMeshMIBGroups 7 }
ciscoLwappMeshNotifsGroupSup1 NOTIFICATION-GROUP
NOTIFICATIONS {
ciscoLwappMeshDefaultBridgeGroupName,
ciscoLwappMeshExcessiveHopCount,
ciscoLwappMeshExcessiveChildren,
ciscoLwappMeshAbateHighSNR,
ciscoLwappMeshOnsetHighSNR
}
STATUS current
DESCRIPTION
"This collection of objects represent the mesh network
related notifications sent by the agent to a network
management station."
::= { ciscoLwappMeshMIBGroups 8 }
ciscoLwappMeshConfigGroupSup2 OBJECT-GROUP
OBJECTS {
clMeshNodeRole,
clMeshNodeGroupName,
clMeshNodeBackhaul,
clMeshNodeBHDataRate,
clMeshNodeEthernetBridge,
clMeshNodeEthernetLinkStatus,
clMeshNodeParentMacAddress,
clMeshNodeHeaterStatus,
clMeshNodeInternalTemp,
clMeshNodeType,
clMeshNodeHops,
clMeshNodeChildCount,
clMeshNodeBackhaulRadio,
clMeshNodeRange,
clMeshBackhaulClientAccess,
clMeshMacFilterList,
clMeshMeshNodeAuthFailureThreshold,
clMeshMeshChildAssociationFailuresThreshold,
clMeshMeshChildExcludedParentInterval,
clMeshSNRThresholdAbate,
clMeshSNRThresholdOnset,
clMeshHighSNRThresholdAbate,
clMeshHighSNRThresholdOnset,
clMeshSNRCheckTimeInterval,
clMeshExcessiveParentChangeThreshold,
clMeshExcessiveParentChangeInterval,
clMeshBackgroundScan,
clMeshAuthenticationMode,
clMeshExcessiveHopCountThreshold,
clMeshExcessiveRapChildThreshold,
clMeshExcessiveMapChildThreshold,
clMeshPublicSafetyBackhaulGlobal,
clMeshisAMSDUEnable,
clMeshIsIdsEnable,
clMeshIsDCAChannelsEnable
}
STATUS current
DESCRIPTION
"This collection of objects represent the
global and mesh node specific configuration
and monitor parameters."
::= { ciscoLwappMeshMIBGroups 9 }
ciscoLwappMeshAtfStatusGroup OBJECT-GROUP
OBJECTS {
clMeshAtfAirtimeUsedInstantaneous,
clMeshAtfAirtimeUsedCumulative,
clMeshAtfFramesSentInstantaneous,
clMeshAtfFramesSentCumulative,
clMeshAtfFramesDroppedInstantaneous,
clMeshAtfFramesDroppedCumulative
}
STATUS current
DESCRIPTION
"This collection of objects represent the
ATF stats for mesh mode APs."
::= { ciscoLwappMeshMIBGroups 10 }
ciscoLwappMeshConfigGroupRev3 OBJECT-GROUP
OBJECTS {
clMeshIsExtendedUAEnable,
clMeshIsBDomainChannelsEnable,
clMeshPskKeyProvisionEnable,
clMeshPskKeyWindowEnable,
clMeshEthenetBridgingVlanTransparent,
clMeshRAPDownlinkBackhaul,
clMeshEthBridgingAllowBpdu,
clMeshIsRapChannelSyncEnabled,
clMeshIsBackhaulRrmEnabled,
clMeshIsCacEnabled
}
STATUS current
DESCRIPTION
"This collection of objects represent the
global and mesh node specific configuration
and monitor parameters."
::= { ciscoLwappMeshMIBGroups 11 }
ciscoLwappMeshPskConfigGroup OBJECT-GROUP
OBJECTS {
clMeshPskIndex,
clMeshPskKey,
clMeshPskTimeStamp,
clMeshPskKeyDesc,
clMeshPskRowStatus,
clMeshPskInUseKeyIndex
}
STATUS current
DESCRIPTION
"This collection of objects represent the
PSK entries of mesh mode APs."
::= { ciscoLwappMeshMIBGroups 12 }
ciscoLwappMeshProfileConfigGroup OBJECT-GROUP
OBJECTS {
cLMeshProfileName,
cLMeshProfileDescr,
cLMeshProfileASTools,
cLMeshProfileAmsdu,
cLMeshProfileBackgroundScan,
cLMeshProfileCcnMode,
cLMeshProfileUniversalAccess,
cLMeshProfileEtherVlanTransparent,
cLMeshProfileFullSectorDfs,
cLMeshProfileIdsState,
cLMeshProfileMulticastMode,
cLMeshProfileRange,
cLMeshProfileSecurityMode,
cLMeshProfileConvergenceMethod,
cLMeshProfileLscOnlyAuthentication,
cLMeshProfileBridgeGroupName,
cLMeshProfileBGNStrictmatch,
cLMeshProfileEthernetBridging,
cLMeshProfileBatteryState,
cLMeshProfileAuthorizationMethod,
cLMeshProfileAuthenticationMethod,
cLMeshProfileDot11bgBhaulRateType,
cLMeshProfileDot11bgBhaulRate,
cLMeshProfileDot11bgBhaulRateDot11nMcsIndex,
cLMeshProfileDot11aBhaulRateType,
cLMeshProfileDot11aBhaulRate,
cLMeshProfileDot11aBhaulRateDot11nMcsIndex,
cLMeshProfileDot11aBhaulRateDot11acMcsIndex,
cLMeshProfileDot11aBhaulRateDot11acSpatialStream,
clMeshProfileRowStatus
}
STATUS deprecated
DESCRIPTION
"This collection of objects represent mesh profile
specific configurations."
::= { ciscoLwappMeshMIBGroups 13 }
ciscoLwappMeshProfileConfigGroupRev1 OBJECT-GROUP
OBJECTS {
cLMeshProfileName,
cLMeshProfileDescr,
cLMeshProfileASTools,
cLMeshProfileAmsdu,
cLMeshProfileBackgroundScan,
cLMeshProfileCcnMode,
cLMeshProfileUniversalAccess,
cLMeshProfileEtherVlanTransparent,
cLMeshProfileFullSectorDfs,
cLMeshProfileIdsState,
cLMeshProfileMulticastMode,
cLMeshProfileRange,
cLMeshProfileSecurityMode,
cLMeshProfileConvergenceMethod,
cLMeshProfileLscOnlyAuthentication,
cLMeshProfileBridgeGroupName,
cLMeshProfileBGNStrictmatch,
cLMeshProfileEthernetBridging,
cLMeshProfileBatteryState,
cLMeshProfileAuthorizationMethod,
cLMeshProfileAuthenticationMethod,
cLMeshProfileDot11bgBhaulRateType,
cLMeshProfileDot11bgBhaulRate,
cLMeshProfileDot11bgBhaulRateDot11nMcsIndex,
cLMeshProfileDot11aBhaulRateType,
cLMeshProfileDot11aBhaulRate,
cLMeshProfileDot11aBhaulRateDot11nMcsIndex,
cLMeshProfileDot11aBhaulRateDot11acMcsIndex,
cLMeshProfileDot11aBhaulRateDot11acSpatialStream,
clMeshProfileRowStatus,
cLMeshProfileDot11bgBhaulRateDot11axMcsIndex,
cLMeshProfileDot11bgBhaulRateDot11axSpatialStream,
cLMeshProfileDot11aBhaulRateDot11axMcsIndex,
cLMeshProfileDot11aBhaulRateDot11axSpatialStream,
clMeshNodeBhaulDataRateDot11axSpatialStream
}
STATUS current
DESCRIPTION
"This collection of objects represent mesh profile
specific configurations."
::= { ciscoLwappMeshMIBGroups 14 }
END
View Git Blame Copy Permalink