WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/cisco/CISCO-LWAPP-DOT11-MIB

2390 lines
86 KiB
Plaintext
Raw Permalink Blame History

-- *******************************************************************
-- CISCO-LWAPP-DOT11-MIB.my
-- January 2007, Devesh Pujari, Srinath Candadai
--
-- Copyright (c) 2007, 2009-2010, 2014-2021, 2023-2024 by Cisco Systems, Inc.
-- All rights reserved.
-- *******************************************************************
CISCO-LWAPP-DOT11-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Unsigned32,
Integer32
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
TruthValue
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
cLApSysMacAddress,
cLApDot11IfSlotId
FROM CISCO-LWAPP-AP-MIB
CLDot11Band,
CLDot11ChannelBandwidth
FROM CISCO-LWAPP-TC-MIB
ciscoMgmt
FROM CISCO-SMI;
-- ********************************************************************
-- * MODULE IDENTITY
-- ********************************************************************
ciscoLwappDot11MIB MODULE-IDENTITY
LAST-UPDATED "202405140000Z"
ORGANIZATION "Cisco Systems Inc."
CONTACT-INFO
"Cisco Systems,
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
Email: cs-wnbu-snmp@cisco.com"
DESCRIPTION
"This MIB is intended to be implemented on all those
devices operating as Central controllers, that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
This MIB provides the information about the
operational parameters of the 802.11 networks.
References about specific type of 802.11 flavors like
802.11a/b/g or 802.11n will be made whereever required
to indicate that the respective parameters are
applicable only to that particular type of 802.11
networks.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+
+ + + + + +
+ CC + + CC + + CC +
+ + + + + +
+......+ +......+ +......+
.. . .
.. . .
. . . .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ AP + + AP + + AP + + AP +
+ + + + + + + +
+......+ +......+ +......+ +......+
. . .
. . . .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ MN + + MN + + MN + + MN +
+ + + + + + + +
+......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Gratuitous Probe Response (GPR)
The Gratuitous Probe Response feature aids in conserving
battery power of WLAN-enabled cell phones by providing
a high rate packet on the order of tens of milliseconds
such that these kind of phones can wake up and wait at
predefined intervals, to reduce battery power. The
GPR packet is transmitted from the AP at a predefined
time interval.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node
and client are used interchangeably.
TU
A measurement of time in units of 1024 microseconds.
802.11n
802.11n builds upon previous 802.11 standards by
adding MIMO (multiple-input multiple-output).
MIMO uses multiple transmitter and receiver antennas
to allow for increased data throughput through spatial
multiplexing and increased range .
A-MPDU
An aggregated format that consists of several MAC
Protocol Data Units being aggregated and transmitted
in one PHY Service Data Unit.
A-MSDU
An aggregated format that consists of several MAC
Service Data Units being aggregated and transmitted
in one MAC Protocol Data Unit.
Reduced Inter-Frame Space ( RIFS )
A time interval between multiple transmissions of a
single transmitter used to reduce overhead and
increase network efficiency.
Modulation and Coding Scheme ( MCS )
This is a value that determines the modulation, coding
and number of spatial channels. Each scheme specifies
the modulation technique, coding rate , number of
spatial streams etc and the corresponding data rate.
Guard Interval
Guard intervals are used to ensure that distinct
transmissions do not interfere with one another.
The purpose of the guard interval is to introduce
immunity to propagation delays, echoes and
reflections, to which digital data is normally
very sensitive.
Media Access Control ( MAC )
The Media Access Control Layer is one of two sublayers
that make up the Data Link Layer. The MAC layer is
responsible for moving data packets to and from one
Network Interface Card (NIC) to another across a shared
channel.
Suppression Table
When the Band Select feature is ON, AP suppresses
the probe response to mobile stations on 2.4 GHz. AP
suppresses probe response to new mobile stattions for
all SSIDs that are being Band Select enabled.
Suppressed mobile station and corresponding suprression
counts are recorded in a table known as Suppression
Table which is stored in internal database of controller.
Entries of this table aged-out to make place for new
entries.
Dual Band Table
When AP sees probe request from any mobile station in
both 2.4GHz and 5GHz band AP will know that mobile station
is capable of operating on both band. Dual band capable
mobile stations are recorded in a table known as dual band
table which is stored in internal database of controller.
This record are kept to make sure 5GHz capable mobile station
should join 5GHz band only.
Entries in the table will be age out to make space for
new entries.
The AP will not respond to the dual band mobile station's
2.4GHz probe until is removed from the dual band
table. AP fills the dual band table in the
following order until it is full:
1) mobile station with 5GHz probe that have associated to
2.4GHz.
2) mobile station with 5GHz probe that also have 2.4GHz
probes.
3) mobile station with just 5GHz probe detected and 5GHz
association.
RSSI
Received Signal Strength Indication (RSSI), the IEEE 802.11
standard defines a mechanism by which RF energy is to be
measured by the circuitry on a wireless NIC. Its value is
measured in dBm and ranges from -128 to 0.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications.
[2] Draft-obara-Capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol.
[3] Enhanced Wireless Consortium MAC Specification,
v1.24.
[4] Enhanced Wireless Consortium PHY Specification,
v1.27."
REVISION "202305300000Z"
DESCRIPTION
"Added below objects to the cld11beMcsTable
- cld11beMcsEntry
- Cld11beMcsEntry
- cldDot11beBand
- cld11beMcsSpatialStreamIndex
- cld11beMcsDataRateIndex
- cld11beMcsSupportEnable"
REVISION "202104160000Z"
DESCRIPTION
"Added below objects to the cld11axObssPdConfigTable
- cld11axSrgObssPdEnable
- cld11axSrgObssPdMin
- cld11axSrgObssPdMax"
REVISION "202101110000Z"
DESCRIPTION
"Added following in cldConfig:
- cldDot116GHzPhy
- cldDot116GHzMediumOccupancyLimit
- cldDot116GHzCFPPeriod
- cldDot116GHzCFPMaxDuration
- cldDot116GHzCFPollable
- cldDot116GHzCFPollRequest
- cldDot116GHzDTIMPeriod
- cldDot116GHzRTSThreshold
- cldDot116GHzShortRetryLimit
- cldDot116GHzLongRetryLimit
- cldDot116GHzFragmentationThreshold
- cldDot116GHzMaxTransmitMSDULifetime
- cldDot116GHzMaxReceiveLifetime
- cldDot116GHzChannelAgilityEnabled
- cldDot116GHzGlobalConfig
- cldDot116GHzNetworkStatus
- cldDot116GHzBeaconPeriod
- cldDot116GHzDynamicChannelAssignment
- cldDot116GHzDynamicChannelUpdateInterval
- cldDot116GHzChannelUpdateCmdInvoke
- cldDot116GHzChannelUpdateCmdStatus
- cldDot116GHzDynamicTransmitPowerControl
- cldDot116GHzCurrentTxPowerLevel
- cldDot116GHzPowerUpdateCmdInvoke
- cldDot116GHzPowerUpdateCmdStatus
- cldDot116GHz80211eMaxBandwidth
- cldDot116GHzDTPCSupport"
REVISION "202009020000Z"
DESCRIPTION
"Added following in cldConfig:
- cldDot11NdpMode
- cldDot11aNdpMode
- cldDot11bNdpMode"
REVISION "202008070000Z"
DESCRIPTION
"Added cld11axObssPdConfigTable to cldConfig."
REVISION "201906280000Z"
DESCRIPTION
"Added the following tables in cldConfig:
cld11axBssColorConfigTable,
cld11axBssColorRadioTable"
REVISION "201902130000Z"
DESCRIPTION
"Added following in cldConfig:
cldLoadBalancingDot11aWindowSize
cldLoadBalancingDot11aDenialCount
cldLoadBalancingDot11bWindowSize
cldLoadBalancingDot11bDenialCount"
REVISION "201705220000Z"
DESCRIPTION
"Added cldVhtDot11acEnable in cld11acConfig.
Added cldLoadBalancingTrafficThreshold in
cldLoadBalancing.
Added following in cld11acMcs table:
cld11acMcsSpatialStreamIndex,
cld11acMcsDataRateIndex,
cld11acMcsSupportEnable"
REVISION "201005060000Z"
DESCRIPTION
"Added cldHtDot11nEnable in CldHtMacOperationsEntry
Added ciscoLwappDot11CountryChangeNotif in
ciscoLwappDot11MIBNotifs
Added following in cldConfig:
cldMultipleCountryCode
cldRegulatoryDomain
cldCountryChangeNotifEnable
cldLoadBalancing
cldLoadBalancingEnable
cldLoadBalancingWindowSize
cldLoadBalancingDenialCount
cldBandSelect
cldBandSelectEnable
cldBandSelectCycleCount
cldBandSelectCycleThreshold
cldBandSelectAgeOutSuppression
cldBandSelectAgeOutDualBand
cldBandSelectClientRssi
cldBandSelectClientMidRssi
cldDot11RxsopThreshold
cldDot11bRxSopThresholdCustom
cldDot11aRxSopThresholdCustom
Added following table:
cld11nMcsTable
cldCountryTable
Added the following OBJECT-GROUPs:
ciscoLwappDot11MIBConfigGroup
ciscoLwappDot11MIBNotifsGroup
ciscoLwappDot11MIBStatusGroup
Added ciscoLwappDot11MIBComplianceRev1 in MODULE-COMPLIANCE"
REVISION "201803280000Z"
DESCRIPTION
"Added the following tables in cldConfig.
cld11axConfigTable,
cld11axMcsTable,
cldDot11axHeCapTable,
cld11axMbssidTable
Added new group ciscoLwappDot11MIBHeStatusGroup."
REVISION "201803280000Z"
DESCRIPTION
"Added the following tables in cldConfig.
cld11axConfigTable,
cld11axMcsTable,
cldDot11axHeCapTable,
cld11axMbssidTable
Added new group ciscoLwappDot11MIBHeStatusGroup.
OBJECT-COMPLIANCE."
REVISION "200701040000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 612 }
ciscoLwappDot11MIBNotifs OBJECT IDENTIFIER
::= { ciscoLwappDot11MIB 0 }
ciscoLwappDot11MIBObjects OBJECT IDENTIFIER
::= { ciscoLwappDot11MIB 1 }
ciscoLwappDot11MIBConform OBJECT IDENTIFIER
::= { ciscoLwappDot11MIB 2 }
cldConfig OBJECT IDENTIFIER
::= { ciscoLwappDot11MIBObjects 1 }
cldStatus OBJECT IDENTIFIER
::= { ciscoLwappDot11MIBObjects 2 }
-- ********************************************************************
-- * High Throughput MAc Operations table
-- ********************************************************************
cldHtMacOperationsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CldHtMacOperationsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the operational parameters
at the MAC layer for the 802.11n networks managed
through the controller. An agent adds an entry to
this table for every 802.11n band on startup."
::= { cldConfig 1 }
cldHtMacOperationsEntry OBJECT-TYPE
SYNTAX CldHtMacOperationsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the operational parameters
at the MAC layer for 802.11n networks."
INDEX { cldHtDot11nBand }
::= { cldHtMacOperationsTable 1 }
CldHtMacOperationsEntry ::= SEQUENCE {
cldHtDot11nBand CLDot11Band,
cldHtDot11nChannelBandwidth CLDot11ChannelBandwidth,
cldHtDot11nRifsEnable TruthValue,
cldHtDot11nAmsduEnable TruthValue,
cldHtDot11nAmpduEnable TruthValue,
cldHtDot11nGuardIntervalEnable TruthValue,
cldHtDot11nEnable TruthValue
}
cldHtDot11nBand OBJECT-TYPE
SYNTAX CLDot11Band
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the 802.11n band the parameters
correspond to."
::= { cldHtMacOperationsEntry 1 }
cldHtDot11nChannelBandwidth OBJECT-TYPE
SYNTAX CLDot11ChannelBandwidth
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object represents the channel bandwidth for
the 802.11n networks in the particular band."
DEFVAL { twenty }
::= { cldHtMacOperationsEntry 2 }
cldHtDot11nRifsEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to indicate the support for RIFS on
this band. A value of 'true' indicates that RIFS is
enabled for this band. A value of 'false' indicates that
RIFS is disabled for this band."
DEFVAL { true }
::= { cldHtMacOperationsEntry 3 }
cldHtDot11nAmsduEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to indicate the support for 802.11n
A-MSDU on this band. A value of 'true' indicates that
A-MSDU is enabled for this band. A value of 'false'
indicates that A-MSDU is disabled for this band."
DEFVAL { true }
::= { cldHtMacOperationsEntry 4 }
cldHtDot11nAmpduEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to indicate the support for 802.11n
A-MPDU on this band. A value of 'true' indicates that
A-MPDU is enabled for this band. A value of 'false'
indicates that A-MPDU is disabled for this band."
DEFVAL { true }
::= { cldHtMacOperationsEntry 5 }
cldHtDot11nGuardIntervalEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to indicate the support for 802.11n
guard interval on this band. A value of 'true' indicates
that guard interval is enabled for this band. A value of
'false' indicates that guard interval is disabled for
this band."
DEFVAL { true }
::= { cldHtMacOperationsEntry 6 }
cldHtDot11nEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable the controller to manage
802.11n networks. A value of 'true' means the 802.11n
network is enabled. A value of 'false' means the 802.11n
network is disabled."
DEFVAL { true }
::= { cldHtMacOperationsEntry 7 }
-- ********************************************************************
-- * Configuration for parameters
-- ********************************************************************
cldMultipleCountryCode OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..600))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object represents the countries in which the
controller is operating. Multiple countries can be set.
The countries are displayed using a 3 letter code
for each country separated by a comma."
::= { cldConfig 2 }
cldRegulatoryDomain OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the regulatory domains for
the controller.
Regulatory domain specifies allowed 802.11 chanels.
Multiple domains can be listed seperated with spaces."
::= { cldConfig 3 }
-- ********************************************************************
-- * MCS table
-- ********************************************************************
cld11nMcsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11nMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists the MCS data rates used on the
802.11n networks managed by this controller."
::= { cldConfig 4 }
cld11nMcsEntry OBJECT-TYPE
SYNTAX Cld11nMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a MCS data rate for 802.11n
band which is uniquely identified by cld11nMcsDataRateIndex
and cld11nMcsBand.
All entries are added by the controller at startup.
cld11nMcsDataRate are calculated by different permutation of
cld11nMcsChannelWidth, cld11nMcsGuardInterval,
cld11nMcsModulation
etc. Different variables combination can give same data rate."
INDEX {
cld11nMcsBand,
cld11nMcsDataRateIndex
}
::= { cld11nMcsTable 1 }
Cld11nMcsEntry ::= SEQUENCE {
cld11nMcsBand CLDot11Band,
cld11nMcsDataRateIndex Unsigned32,
cld11nMcsDataRate Unsigned32,
cld11nMcsSupportEnable TruthValue,
cld11nMcsChannelWidth Unsigned32,
cld11nMcsGuardInterval Unsigned32,
cld11nMcsModulation OCTET STRING
}
cld11nMcsBand OBJECT-TYPE
SYNTAX CLDot11Band
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the 802.11n band to which
the data rate is applicable."
::= { cld11nMcsEntry 1 }
cld11nMcsDataRateIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies the data rate
for a particular band."
::= { cld11nMcsEntry 2 }
cld11nMcsDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the data rate value for this
band."
::= { cld11nMcsEntry 3 }
cld11nMcsSupportEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable or disable the data
rate. When this object is set to 'true' the MCS
support is enabled. When this object is set
to 'false' the MCS support is disabled.."
DEFVAL { true }
::= { cld11nMcsEntry 4 }
cld11nMcsChannelWidth OBJECT-TYPE
SYNTAX Unsigned32
UNITS "MHz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the channel width for which
cld11nMcsDataRate has been calculated."
::= { cld11nMcsEntry 5 }
cld11nMcsGuardInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "ns"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the guard interval for which
cld11nMcsDataRate has been calculated."
::= { cld11nMcsEntry 6 }
cld11nMcsModulation OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the modulation used to calculate
cld11nMcsDataRate."
::= { cld11nMcsEntry 7 }
-- *****************************
-- LOAD BALANCING CONFIGURATION
-- *****************************
cld11acConfig OBJECT IDENTIFIER
::= { cldConfig 5 }
cldVhtDot11acEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable the controller to manage
802.11ac networks. A value of 'true' means the 802.11ac
network is enabled. A value of 'false' means the 802.11ac
network is disabled."
DEFVAL { true }
::= { cld11acConfig 1 }
-- ********************************************************************
-- * MCS table
-- ********************************************************************
cld11acMcsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11acMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to configure 802.11ac specific MCS
data rate settings on a controller."
::= { cldConfig 6 }
cld11acMcsEntry OBJECT-TYPE
SYNTAX Cld11acMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the additional MCS data
rate for 802.11ac band which is uniquely identifies by
cld11acMcsSpatialStreamIndex and cld11acMcsDataRateIndex.
All entries are added by the controller at startup."
INDEX {
cld11acMcsSpatialStreamIndex,
cld11acMcsDataRateIndex
}
::= { cld11acMcsTable 1 }
Cld11acMcsEntry ::= SEQUENCE {
cld11acMcsSpatialStreamIndex Unsigned32,
cld11acMcsDataRateIndex Unsigned32,
cld11acMcsSupportEnable TruthValue
}
cld11acMcsSpatialStreamIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The object represents the spatial stream number
related to MCS data rate settings on the 802.11ac
band."
::= { cld11acMcsEntry 1 }
cld11acMcsDataRateIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object uniquely identifies the data rate
for a particular band."
::= { cld11acMcsEntry 2 }
cld11acMcsSupportEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable or disable the data
rate. When this object is set to 'true' the MCS
support is enabled. When this object is set
to 'false' the MCS support is disabled.."
DEFVAL { true }
::= { cld11acMcsEntry 3 }
-- *****************************
-- LOAD BALANCING CONFIGURATION
-- *****************************
cldLoadBalancing OBJECT IDENTIFIER
::= { cldConfig 8 }
cldLoadBalancingEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the mode of Load Balancing.
Value of 1(enable) shows that the Load Balancing
is enabled and value of 2(disable) shows that it is
disabled.
If Load balancing is enable and wireless mobile station tries
to
associate any overloaded AP, association rejection
will be sent to mobile station from AP.
From 7.0 release onwards Load Balancing cannot be configured
globally. cldLoadBalancingEnable will be read-only attribute
and it will always be enable.
Use cLWlanLoadBalancingEnable to configure it per WLAN."
DEFVAL { enable }
::= { cldLoadBalancing 1 }
cldLoadBalancingWindowSize OBJECT-TYPE
SYNTAX Integer32 (0..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the threshold for the difference
between number of mobile station a given AP can have and
mobile station count of the AP having minimum number of
mobile station in the setup.
For example, suppose in a network setup there are three
APs are connected to Controller, say AP1, AP2 and AP3.
AP1 have 2 mobile stations, AP2 have 3 and AP3 have 4
mobile stations.
Here AP1 have minimum number of mobile stations i.e. 2.
Suppose window size is configured as 2. So every AP can have
2+2=4 mobile stations. So every 5th mobile station will be
load balanced.
So, if any mobile station tries to join AP3, denial will be sent
from AP3. For a mobile station denial will be send only for
cldLoadBalancingDenialCount number of time."
DEFVAL { 5 }
::= { cldLoadBalancing 2 }
cldLoadBalancingDenialCount OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies maximum number of association
rejection AP will send to a mobile station for a given sequence
of association.
When a mobile station tries to associate on wireless network, it
sends association request to AP. If AP is overloaded and
load balancing is enable on controller, AP will send a
denial to association request. If there are no other AP
in the vicinity of mobile station, it will try to associate same
AP again. So to restrict the number of denial sent from
AP, cldLoadBalancingDenialCount is defined. After maximum
denial count is reached mobile station will be able to
associate.
Association attempts on an AP from any mobile station before
associating any AP is called as sequence of assoociation."
DEFVAL { 3 }
::= { cldLoadBalancing 3 }
cldLoadBalancingTrafficThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the traffic threshold that
triggers 'uplinkUsage' based load balancing. When the
uplink usage of an AP is above this threshold, this AP
is valid for 'uplinkUsage' based load balancing, if
load balance is enabled by cLWlanLoadBalancingEnable
and 'uplinkUsage' mode is chosen by cLWlanLoadBalancingMode
at that WLAN."
DEFVAL { 50 }
::= { cldLoadBalancing 4 }
cldLoadBalancingDot11aWindowSize OBJECT-TYPE
SYNTAX Integer32 (0..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the threshold for the difference
between number of mobile station a given AP can have and
mobile station count of the AP having minimum number of
mobile station in the setup.
For example, suppose in a network setup there are three
APs are connected to Controller, say AP1, AP2 and AP3.
AP1 have 2 mobile stations, AP2 have 3 and AP3 have 4
mobile stations.
Here AP1 have minimum number of mobile stations i.e. 2.
Suppose window size is configured as 2. So every AP can have
2+2=4 mobile stations. So every 5th mobile station will be
load balanced.
So, if any mobile station tries to join AP3, denial will be sent
from AP3. For a mobile station denial will be send only for
cldLoadBalancingDenialCount number of time."
DEFVAL { 5 }
::= { cldLoadBalancing 5 }
cldLoadBalancingDot11aDenialCount OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies maximum number of association
rejection AP will send to a mobile station for a given sequence
of association.
When a mobile station tries to associate on wireless network, it
sends association request to AP. If AP is overloaded and
load balancing is enable on controller, AP will send a
denial to association request. If there are no other AP
in the vicinity of mobile station, it will try to associate same
AP again. So to restrict the number of denial sent from
AP, cldLoadBalancingDenialCount is defined. After maximum
denial count is reached mobile station will be able to
associate.
Association attempts on an AP from any mobile station before
associating any AP is called as sequence of assoociation."
DEFVAL { 3 }
::= { cldLoadBalancing 6 }
cldLoadBalancingDot11bWindowSize OBJECT-TYPE
SYNTAX Integer32 (0..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the threshold for the difference
between number of mobile station a given AP can have and
mobile station count of the AP having minimum number of
mobile station in the setup.
For example, suppose in a network setup there are three
APs are connected to Controller, say AP1, AP2 and AP3.
AP1 have 2 mobile stations, AP2 have 3 and AP3 have 4
mobile stations.
Here AP1 have minimum number of mobile stations i.e. 2.
Suppose window size is configured as 2. So every AP can have
2+2=4 mobile stations. So every 5th mobile station will be
load balanced.
So, if any mobile station tries to join AP3, denial will be sent
from AP3. For a mobile station denial will be send only for
cldLoadBalancingDenialCount number of time."
DEFVAL { 5 }
::= { cldLoadBalancing 7 }
cldLoadBalancingDot11bDenialCount OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies maximum number of association
rejection AP will send to a mobile station for a given sequence
of association.
When a mobile station tries to associate on wireless network, it
sends association request to AP. If AP is overloaded and
load balancing is enable on controller, AP will send a
denial to association request. If there are no other AP
in the vicinity of mobile station, it will try to associate same
AP again. So to restrict the number of denial sent from
AP, cldLoadBalancingDenialCount is defined. After maximum
denial count is reached mobile station will be able to
associate.
Association attempts on an AP from any mobile station before
associating any AP is called as sequence of assoociation."
DEFVAL { 3 }
::= { cldLoadBalancing 8 }
-- **************************
-- BAND SELECT CONFIGURATION
-- **************************
cldBandSelect OBJECT IDENTIFIER
::= { cldConfig 9 }
cldBandSelectEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the mode of Band Select.
Value of 1(enable) shows that the Band Select
is enabled and value of 2(disable) shows that it is
disabled.
If Band Select is enable AP suppresses probe response
to new mobile station. AP will suppress probe request coming
only on 2.4 GHz radio.
From 7.0 release onwards Band Select cannot be configured
globally. cldBandSelectEnable will be read-only attribute
and it will always be enable.
Use cLWlanBandSelectEnable to configure it per WLAN."
DEFVAL { enable }
::= { cldBandSelect 1 }
cldBandSelectCycleCount OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies band select probe mobile station count.
Suppressed mobile stations and corresponding suppression count
are recorded in a suppression table which is stored in
internal database of controllers. AP will suppress
probe request of a mobile station till value of cycle count.
AP will increment cycle counter when a mobile station scan
a channel on 2.4GHz band after any time greater than
cldBandSelectCycleThreshold.
When a mobile station cycle count is reached and if mobile
station still sends a probe request then AP will respond
to it by probe response.
For example, we assume at minimum, a mobile station
will stay in a channel for 5 milliseconds and there are
11 channels. If the mobile station scans channel 1 and then the
other 10 channels, there should be at least a gap of 10x5
milliseconds between the last time AP hears the mobile station
probe and the latest one. AP only increments the count if
the difference of time between the latest and the last
probe is more than 50 milliseconds."
DEFVAL { 3 }
::= { cldBandSelect 2 }
cldBandSelectCycleThreshold OBJECT-TYPE
SYNTAX Integer32 (1..1000)
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies time threshold for a new scanning
mobile station period. Mobile station cycle counter will
increment only if mobile station scans same channel any
time after cldBandSelectCycleThreshold is passed.
For example, if a mobile station is scanning a channel after
every 150 milliseconds and cycle threshold value is
configures as 200, then cycle count will be incremented
after 300 seconds. But if mobile station is scanning after every
250 milliseconds, then mobile station count will be incremented
after 250 milliseconds."
DEFVAL { 200 }
::= { cldBandSelect 3 }
cldBandSelectAgeOutSuppression OBJECT-TYPE
SYNTAX Integer32 (10..200)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Suppressed mobile station are recorded in a suppression table.
This object specifies age out period after which entry
of mobile station will be removed.
All entries will stay in the table until it is aged
out or is replaced when table is full. If table is
full, and there is no space for new mobile station then AP
will replaced the oldest entry on the table that it
had responded already. If there as no empty slot in
the table, AP has to respond to all the new mobile station
until space starts getting available."
DEFVAL { 20 }
::= { cldBandSelect 4 }
cldBandSelectAgeOutDualBand OBJECT-TYPE
SYNTAX Integer32 (10..300)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects specifies age out period after which mobile
station entry will be removed for dual band AP.
When AP sees probe request from any mobile station in both
2.4GHz and 5GHz band AP will know that mobile station is
capable of operating on both band. Dual band capable
mobile stations are recorded in a dual band table which
is stored in internal database of controllers.
This record are kept to make sure 5GHz capable mobile station
should join 5GHz band only.
Entries in the table will be age out to make space for
new entries.
The AP will not respond to the dual band mobile station's
2.4GHz probe until is removed from the dual band
table. AP fills the dual band table in the
following order until it is full:
1) mobile station with 5GHz probe that have associated to
2.4GHz.
2) mobile station with 5GHz probe that also have 2.4GHz
probes.
3) mobile station with just 5GHz probe detected and 5GHz
association."
DEFVAL { 60 }
::= { cldBandSelect 5 }
cldBandSelectClientRssi OBJECT-TYPE
SYNTAX Integer32 (-90..-20)
UNITS "dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies minimum mobile station RSSI threshold.
Mobile stations having RSSI below this value will not be
recorded in suppressed table.
This configuration filter out far away mobile stations with
low signal strength. This will limit the number of
mobile stations on the table to a reasonable amount."
DEFVAL { -80 }
::= { cldBandSelect 6 }
cldBandSelectClientMidRssi OBJECT-TYPE
SYNTAX Integer32 (-90..-20)
UNITS "dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies medium mobile station RSSI threshold.
Mobile station between this value and cldBandSelectClientRssi
will be recorded in suppressed table but will not be denied.
The mobile station having RSSI stronger this value will be recorded
and denied."
DEFVAL { -80 }
::= { cldBandSelect 7 }
-- ***********************************************************
-- 11ax CONFIGURATION
-- ***********************************************************
cld11axConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the operational parameters
at the MAC layer for the 802.11ax networks managed
through the controller. An agent adds an entry to
this table for every 802.11ax band on startup."
::= { cldConfig 10 }
cld11axConfigEntry OBJECT-TYPE
SYNTAX Cld11axConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the configurational parameters
of 802.11ax networks."
INDEX { cldDot11axBandId }
::= { cld11axConfigTable 1 }
Cld11axConfigEntry ::= SEQUENCE {
cldDot11axBandId CLDot11Band,
cldDot11axEnable TruthValue
}
cldDot11axBandId OBJECT-TYPE
SYNTAX CLDot11Band
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the 802.11ax band the parameters
correspond to."
::= { cld11axConfigEntry 1 }
cldDot11axEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the status of 802.11ax networks
in controller. A value of 'true' means the 802.11ax
network is enabled. A value of 'false' means the 802.11ax
network is disabled."
DEFVAL { true }
::= { cld11axConfigEntry 2 }
cld11axMcsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the operational parameters
at the MAC layer for the 802.11ax networks managed
through the controller. An agent adds an entry to
this table for every 802.11ax band on startup."
::= { cldConfig 11 }
cld11axMcsEntry OBJECT-TYPE
SYNTAX Cld11axMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the configurational parameters
of 802.11ax networks."
INDEX { cldDot11axBand,
cld11axMcsSpatialStreamIndex,
cld11axMcsDataRateIndex
}
::= { cld11axMcsTable 1 }
Cld11axMcsEntry ::= SEQUENCE {
cldDot11axBand CLDot11Band,
cld11axMcsSpatialStreamIndex Unsigned32,
cld11axMcsDataRateIndex Unsigned32,
cld11axMcsSupportEnable TruthValue
}
cldDot11axBand OBJECT-TYPE
SYNTAX CLDot11Band
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the 802.11ax band the parameters
correspond to."
::= { cld11axMcsEntry 1 }
cld11axMcsSpatialStreamIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The object represents the spatial stream number
related to MCS data rate settings on the 802.11ax
band."
::= { cld11axMcsEntry 2 }
cld11axMcsDataRateIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the data rate for a
particular band."
::= { cld11axMcsEntry 3 }
cld11axMcsSupportEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies a option to enable or disable the data
rate.
A value of 'true' indicates the MCS support is enabled.
A value of 'false' indicates the MCS support is disabled."
DEFVAL { true }
::= { cld11axMcsEntry 4 }
cldDot11axHeCapTable OBJECT-TYPE
SYNTAX SEQUENCE OF CldDot11axHeCapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the HE capabilities
at the MAC layer for the 802.11ax networks managed
through the controller. An agent adds an entry to
this table for every 802.11ax band on startup."
::= { cldConfig 12 }
cldDot11axHeCapEntry OBJECT-TYPE
SYNTAX CldDot11axHeCapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the configurational HE parameters
of 802.11ax networks."
INDEX { cLApSysMacAddress,
cLApDot11IfSlotId }
::= { cldDot11axHeCapTable 1 }
CldDot11axHeCapEntry ::= SEQUENCE {
cldDot11IsHeCapable TruthValue,
cldDot11IsHeEnable TruthValue,
cldDot11HeSuBF Unsigned32,
cldDot11HeMuBF Unsigned32,
cldDot11HeStbcMode Unsigned32,
cldDot11HeAmpduTidBmap Unsigned32,
cldDot11HeCapTxRxMcsNss Unsigned32
}
cldDot11IsHeCapable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the HE capability of
802.11ax radio."
::= { cldDot11axHeCapEntry 1 }
cldDot11IsHeEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents status of HE mode of
802.11ax radio."
::= { cldDot11axHeCapEntry 2 }
cldDot11HeSuBF OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the AP operation as a
SU beamformer in HE mode status."
::= { cldDot11axHeCapEntry 3 }
cldDot11HeMuBF OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the AP operation as a
MU beamformer in HE mode status."
::= { cldDot11axHeCapEntry 4 }
cldDot11HeStbcMode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the HE STBC TX-RX mode
status of the AP."
::= { cldDot11axHeCapEntry 5 }
cldDot11HeAmpduTidBmap OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the number of TIDs. The value
is number of TIDs minus 1 of QoS Data frames that an
HE STA can aggregate in a multi-TID AMPDU."
::= { cldDot11axHeCapEntry 6 }
cldDot11HeCapTxRxMcsNss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents Tx Rx HE MCS NSS Support of AP."
::= { cldDot11axHeCapEntry 7 }
cld11axMbssidTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axMbssidEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the configuration of 802.11ax
specific Mbssid settings on a controller."
::= { cldConfig 13 }
cld11axMbssidEntry OBJECT-TYPE
SYNTAX Cld11axMbssidEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the Mbssid parameters
on a controller."
INDEX {
cldBand
}
::= { cld11axMbssidTable 1 }
Cld11axMbssidEntry ::= SEQUENCE {
cldBand CLDot11Band,
cld11axMbssidCap TruthValue
}
cldBand OBJECT-TYPE
SYNTAX CLDot11Band
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the 802.11ax band the parameters
correspond to."
::= { cld11axMbssidEntry 1 }
cld11axMbssidCap OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the state of the Mbssid support on
802.11ax networks. A value of 'true' means Mbssid in the
network is enabled. A value of 'false' means Mbssid in the
network is disabled."
::= { cld11axMbssidEntry 2 }
cld11axTargetWakeupTimeTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axTargetWakeupTimeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the configuration of 802.11ax
specific target wake-up time settings on a controller."
::= { cldConfig 15 }
cld11axTargetWakeupTimeEntry OBJECT-TYPE
SYNTAX Cld11axTargetWakeupTimeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the target wake-up time
parameters on a controller."
INDEX {
cldBand
}
::= { cld11axTargetWakeupTimeTable 1 }
Cld11axTargetWakeupTimeEntry ::= SEQUENCE {
cldBand CLDot11Band,
cld11axTargetWakeupTimeEnable TruthValue
}
cld11axTargetWakeupTimeEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether 802.11ax target wake-up time is enabled
or disabled.
Target wake-up time is a function that permits an AP to
define a specific time or set of times for individual stations
to access the medium.
A value of 'true' indicates that 802.11ax Target wake-up time is enabled.
A value of 'false' indicates that 802.11ax Target wake-up time is disabled."
DEFVAL { true }
::= { cld11axTargetWakeupTimeEntry 1 }
cld11axTargetWakeupTimeBroadcastTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axTargetWakeupTimeBoradcastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the 802.11ax target wake-up time broadcast
configurations on a controller."
::= { cldConfig 16 }
cld11axTargetWakeupTimeBroadcastEntry OBJECT-TYPE
SYNTAX Cld11axTargetWakeupTimeBroadcastEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the target wake-up time broadcast
parameters on a controller."
INDEX {
cldBand
}
::= { cld11axTargetWakeupTimeBroadcastTable 1 }
Cld11axTargetWakeupTimeBroadcastEntry ::= SEQUENCE {
cldBand CLDot11Band,
cld11axTargetWakeupTimeBroadcastEnable TruthValue
}
cld11axTargetWakeupTimeBroadcastEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether 802.11ax target wake-up time broadcast
is enabled or disabled.
A value of 'true' indicates that 802.11ax target wake-up time broadcast
is enabled.
A value of 'false' indicates that 802.11ax target wake-up time broadcast
is disabled."
DEFVAL { true }
::= { cld11axTargetWakeupTimeBroadcastEntry 1 }
cld11axBssColorConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axBssColorConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the configuration of network
802.11ax BSS Color settings on a controller."
::= { cldConfig 17 }
cld11axBssColorConfigEntry OBJECT-TYPE
SYNTAX Cld11axBssColorConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the 802.11ax
BSS Color network parameters on a controller."
INDEX {
cldBand
}
::= { cld11axBssColorConfigTable 1 }
Cld11axBssColorConfigEntry ::= SEQUENCE {
cldBand CLDot11Band,
cld11axBssColorState TruthValue
}
cld11axBssColorState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the state of the BSS Color support on
802.11ax networks. A value of 'true' means BSS Color in the
network is enabled. A value of 'false' means BSS Color in the
network is disabled."
::= { cld11axBssColorConfigEntry 1 }
cld11axBssColorRadioTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axBssColorRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents AP radio-specific 802.11ax
BSS Color capability and configuration."
::= { cldConfig 18 }
cld11axBssColorRadioEntry OBJECT-TYPE
SYNTAX Cld11axBssColorRadioEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents an 802.11ax BSS color parameter
for the given AP radio."
INDEX { cLApSysMacAddress,
cLApDot11IfSlotId }
::= { cld11axBssColorRadioTable 1 }
Cld11axBssColorRadioEntry ::= SEQUENCE {
cld11axIsBssColorCapable TruthValue,
cld11axBssColor INTEGER,
cld11axBssColorConfigType INTEGER
}
cld11axIsBssColorCapable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The object represents the 802.11ax BSS color capability
of the radio."
::= { cld11axBssColorRadioEntry 1 }
cld11axBssColor OBJECT-TYPE
SYNTAX INTEGER (0..63)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object represents the configured BSS color of the
802.11ax radio. Valid values are between 0 and 63, where
0 means disabled. This attribute can be set only if
cld11axBssColorConfigType is set to customized."
::= { cld11axBssColorRadioEntry 2 }
cld11axBssColorConfigType OBJECT-TYPE
SYNTAX INTEGER {
automatic(1),
customized(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this value is 1 (automatic), then cld11axBssColor is
assigned by dynamic algorithm and read-only. If this value
is 2 (customized), then cld11axBssColor is read-write and
allowed to be set"
::= { cld11axBssColorRadioEntry 3 }
cld11axObssPdConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11axObssPdConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the configuration of network
802.11ax OBSS PD settings on a controller."
::= { cldConfig 20 }
cld11axObssPdConfigEntry OBJECT-TYPE
SYNTAX Cld11axObssPdConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the 802.11ax
OBSS PD network parameters on a controller."
INDEX {
cldBand
}
::= { cld11axObssPdConfigTable 1 }
Cld11axObssPdConfigEntry ::= SEQUENCE {
cldBand CLDot11Band,
cld11axObssPdEnable TruthValue,
cld11axNonSrgObssPdMax Integer32,
cld11axSrgObssPdEnable TruthValue,
cld11axSrgObssPdMin Integer32,
cld11axSrgObssPdMax Integer32
}
cld11axObssPdEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the state of the OBSS PD spatial reuse
support on 802.11ax networks. A value of 'true' means OBSS PD
in the network is enabled. A value of 'false' means OBSS PD in
the network is disabled."
DEFVAL { false }
::= { cld11axObssPdConfigEntry 1 }
cld11axNonSrgObssPdMax OBJECT-TYPE
SYNTAX Integer32 (-82..-62)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the non-SRG OBSS PD max threshold in dBm on
802.11ax networks."
DEFVAL { -62 }
::= { cld11axObssPdConfigEntry 2 }
cld11axSrgObssPdEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the state of the SRG OBSS PD spatial reuse
support on 802.11ax networks. A value of 'true' means SRG OBSS PD
in the network is enabled. A value of 'false' means SRG OBSS PD in
the network is disabled."
DEFVAL { false }
::= { cld11axObssPdConfigEntry 3 }
cld11axSrgObssPdMin OBJECT-TYPE
SYNTAX Integer32 (-82..-62)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the SRG OBSS PD min threshold in dBm on
802.11ax networks."
DEFVAL { -82 }
::= { cld11axObssPdConfigEntry 4 }
cld11axSrgObssPdMax OBJECT-TYPE
SYNTAX Integer32 (-82..-62)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the SRG OBSS PD max threshold in dBm on
802.11ax networks."
DEFVAL { -62 }
::= { cld11axObssPdConfigEntry 5 }
-- *****************************
-- RXSOP THRESHOLD CONFIGURATION
-- *****************************
cldDot11RxsopThreshold OBJECT IDENTIFIER
::= { cldConfig 14 }
cldDot11bRxSopThresholdCustom OBJECT-TYPE
SYNTAX INTEGER (-85..-60)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute is used to configure Rxsop or receiver start
of packet custom values for 802.11b/g radios.
bsnGlobalDot11bRxSopThreshold should be set to custom for
cldDot11bRxSopThresholdCustom configured value to be used"
DEFVAL { -85 }
::= { cldDot11RxsopThreshold 1 }
cldDot11aRxSopThresholdCustom OBJECT-TYPE
SYNTAX INTEGER (-85..-60)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute is used to configure Rxsop or receiver start
of packet custom values for 802.11b/g radios.
bsnGlobalDot11aRxSopThreshold should be set to custom for
cldDot11aRxSopThresholdCustom configured value to be used"
DEFVAL { -85 }
::= { cldDot11RxsopThreshold 2 }
-- *************************************
-- Neighbor Discovery mode CONFIGURATION
-- *************************************
cldDot11NdpMode OBJECT IDENTIFIER
::= { cldConfig 21 }
cldDot11bNdpMode OBJECT-TYPE
SYNTAX INTEGER (0..1)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute is used to configure neighbor
discovery mode for 802.11b/g radios."
DEFVAL { 0 }
::= { cldDot11NdpMode 1 }
cldDot11aNdpMode OBJECT-TYPE
SYNTAX INTEGER (0..1)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute is used to configure neighbor
discovery mode for 802.11a radios."
DEFVAL { 0 }
::= { cldDot11NdpMode 2 }
-- ********************************************************************
-- * Begin of cldDot116GHzPhy
-- ********************************************************************
cldDot116GHzPhy OBJECT IDENTIFIER
::= { cldConfig 22 }
cldDot116GHzMediumOccupancyLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHz band shall indicate the maximum amount
of time in TU, that a point coordinator may control
the usage of the wireless medium without relinquishing control
for long enough to allow at least one instance of DCF access
to the medium. The default value of this attribute shall be 100."
::= { cldDot116GHzPhy 1 }
cldDot116GHzCFPPeriod OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The attribute for 6GHz band shall describe the number of
DTIM intervals between the start of CFPs. It is modified by
MLME-START.request primitive. Default value is 4"
::= { cldDot116GHzPhy 2 }
cldDot116GHzCFPMaxDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The attribute for 6GHz band shall describe the maximum
duration of the CFP in TU that may be generated by the PCF.
It is modified by MLME-START.request primitive.
Default value is 60."
::= { cldDot116GHzPhy 3 }
cldDot116GHzCFPollable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When this attribute is true, it shall indicate that the STA
is able to respond to a CF-Poll with a data frame within a
SIFS time for 6GHz band. This attribute shall be false if the
STA is not able to respond to a CF-Poll with a data frame
within a SIFS time. Default value is false."
::= { cldDot116GHzPhy 4 }
cldDot116GHzCFPollRequest OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether CFP is requested by Mobile
Station or not for 6GHz band. Default value is false."
::= { cldDot116GHzPhy 5 }
cldDot116GHzDTIMPeriod OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHz band shall specify the number
of beacon intervals that shall elapse between transmission of
Beacons frames containing a TIM element whose DTIM
Count field is 0. This value is transmitted in the DTIM Period
field of Beacon frames. Default value is 1."
::= { cldDot116GHzPhy 6 }
cldDot116GHzRTSThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHz band shall indicate the number of octets
in an MPDU, below which an RTS/CTS handshake shall not be performed.
An RTS/CTS handshake shall be performed at the beginning of any
frame exchange sequence where the MPDU is of type Data or
Management, the MPDU has an individual address in the Address1
field, and the length of the MPDU is greater than
this threshold. (For additional details, refer to Table 21 in
9.7.) Setting this attribute to be larger than the maximum
MSDU size shall have the effect of turning off the RTS/CTS
handshake for frames of Data or Management type transmitted by
this STA. Setting this attribute to zero shall have the effect
of turning on the RTS/CTS handshake for all frames of Data or
Management type transmitted by this STA. The default value of
this attribute shall be 2347."
::= { cldDot116GHzPhy 7 }
cldDot116GHzShortRetryLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHZ band shall indicate the maximum number of
transmission attempts of a frame, the length of which is less
than or equal to bsnGlobalDot11RTSThreshold, that shall be
made before a failure condition is indicated. The default
value of this attribute shall be 7."
::= { cldDot116GHzPhy 8 }
cldDot116GHzLongRetryLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHZ band shall indicate the maximum number of
transmission attempts of a frame, the length of which is
greater than bsnGlobalDot11RTSThreshold, that shall be made
before a failure condition is indicated. The default value of
this attribute shall be 4."
::= { cldDot116GHzPhy 9 }
cldDot116GHzFragmentationThreshold OBJECT-TYPE
SYNTAX Unsigned32 (256..2346)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute for 6GHz band shall specify the current maximum size,
in octets, of the MPDU that may be delivered to the PHY. An MSDU
shall be broken into fragments if its size exceeds the value
of this attribute after adding MAC headers and trailers. MSDU
or MMPDU shall be fragmented when the resulting frame has an
individual address in the Address1 field, and the length of the
frame is larger than this threshold. The default value for this
attribute shall be the lesser of 2346 or the aMPDUMaxLength of
the attached PHY and shall never exceed the lesser of 2346 or
the aMPDUMaxLength of the attached PHY. The value of this
attribute shall never be less than 256."
DEFVAL { 2346 }
::= { cldDot116GHzPhy 10 }
cldDot116GHzMaxTransmitMSDULifetime OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHz band represents the elapsed time in TU,
after the initial transmission of an MSDU, after which further
attempts to transmit the MSDU shall be terminated. The default
value of this attribute shall be 512."
::= { cldDot116GHzPhy 11 }
cldDot116GHzMaxReceiveLifetime OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHz band represents the elapsed time in TU,
after the initial reception of a fragmented MMPDU or MSDU,
after which further attempts to reassemble the MMPDU or
MSDU shall be terminated. The default value shall be
512."
::= { cldDot116GHzPhy 12 }
cldDot116GHzChannelAgilityEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute for 6GHz band indicates whether the PHY channel
agility functionality is enabled. Default value is false."
::= { cldDot116GHzPhy 13 }
-- ********************************************************************
-- * BSN Global Parameters for Dot11 6GHz
-- ********************************************************************
cldDot116GHzGlobalConfig OBJECT IDENTIFIER
::= { cldConfig 23 }
cldDot116GHzNetworkStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Dot11 6GHz Network Status"
DEFVAL { true }
::= { cldDot116GHzGlobalConfig 1 }
cldDot116GHzBeaconPeriod OBJECT-TYPE
SYNTAX Unsigned32 (20..1000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute for 6GHz band shall specify the number of TU that
a AP Radio shall use for scheduling Beacon tranmissions.
This value is transmitted in Beacon and Probe Response
frames."
DEFVAL { 100 }
::= { cldDot116GHzGlobalConfig 2 }
cldDot116GHzDynamicChannelAssignment OBJECT-TYPE
SYNTAX INTEGER {
automatic(1),
runOnce(2),
static(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute for 6GHz band specifies the Dynamic channel assignment
(DCA) which has three modes. When the mode is auto, the channel
assignment will be periodically updated for all Cisco APs that permit
this operation. When the DCA is runOnce, channel assignments are updated
based on the UPDATE_CMD received from the management. When the DCA is
static, no dynamic channel assignments occurs and value are
set to their global default. Default is auto."
DEFVAL { automatic }
::= { cldDot116GHzGlobalConfig 3 }
cldDot116GHzDynamicChannelUpdateInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When Channel dynamic alogirthm is running, this interval(in
secs) for 6GHz band specifies how often Channel assignement
updates are attempted on an Cisco AP. NOTE: hysteresis is
build into the algorithms so we will not have uproductive
changes occuring. Default value is 600 secs"
DEFVAL { 600 }
::= { cldDot116GHzGlobalConfig 4 }
cldDot116GHzChannelUpdateCmdInvoke OBJECT-TYPE
SYNTAX INTEGER {
default(0),
activate(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute for 6GHz band, when set to activate,
starts a DCA calculation regardless of the dynamic update interval.
This command should be invoke on Group Leader Cisco Switch.
Invoking on a Cisco switch which is not a Group leader has no effect."
::= { cldDot116GHzGlobalConfig 5 }
cldDot116GHzChannelUpdateCmdStatus OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"After setting cldDot116GHzChannelUpdateCmdInvoke to
activate, the result of action can be monitored from here. It
takes 5 minutes for the command to complete."
::= { cldDot116GHzGlobalConfig 6 }
cldDot116GHzDynamicTransmitPowerControl OBJECT-TYPE
SYNTAX INTEGER {
automatic(1),
runOnce(2),
static(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute for 6GHz band represents the Dynamic transmit
power(DTP) mode, which is of three types. When the mode is auto,
the transmit power of each Cisco AP will be periodically updated for
all Cisco APs that permit this operation. When the DTP is runOnce,
transmit power update will occur based on the UPDATE_CMD received from
the management. When the DTP is static, no dynamic transmit power updates
occur and their global defaults are used. Default is auto."
DEFVAL { automatic }
::= { cldDot116GHzGlobalConfig 7 }
cldDot116GHzCurrentTxPowerLevel OBJECT-TYPE
SYNTAX Integer32 (0..5)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute for 6GHz band represents the TxPowerLevel N that is
is currently being used to transmit data. Some PHYs also use this
value to determine the receiver sensitivity requirements for CCA."
DEFVAL { 1 }
::= { cldDot116GHzGlobalConfig 8 }
cldDot116GHzPowerUpdateCmdInvoke OBJECT-TYPE
SYNTAX INTEGER {
default(0),
activate(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute for 6GHz band, when set to activate, starts a DTP
calculation regardless of the dynamic update interval. This command
should be invoked on Group Leader Cisco Switch. Invoking on a
Cisco switch which is not a Group leader has no effect."
::= { cldDot116GHzGlobalConfig 9 }
cldDot116GHzPowerUpdateCmdStatus OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"After setting cldDot116GHzChannelUpdateCmdInvoke to
activate, the result of action can be monitored from here. It
takes 5 minutes for the command to complete."
::= { cldDot116GHzGlobalConfig 10 }
cldDot116GHz80211eMaxBandwidth OBJECT-TYPE
SYNTAX Integer32 (5..85)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This represents the maximum bandwidth allocated to 802.11e
clients. It is expressed as percentage of the total bandwidth
of 802.11 6GHz network. The value of this attribute can vary from
5 to 85."
DEFVAL { 75 }
::= { cldDot116GHzGlobalConfig 11 }
cldDot116GHzDTPCSupport OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This attribute may be used to enable the DTPC support on all
802.11 6GHz radios. DTPC or Dynamic Transmit Power Control support
means that the radio's transmit power will be advertised in the
beacons and probe responses."
DEFVAL { true }
::= { cldDot116GHzGlobalConfig 12 }
-- ********************************************************************
-- Channel table for all Country codes
-- ********************************************************************
cldCountryTable OBJECT-TYPE
SYNTAX SEQUENCE OF CldCountryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the list of countries and the
network parameters specific to the respective
countries. It shows the 802.11 networks, managed by
this controller, where controller can operate."
::= { cldStatus 1 }
cldCountryEntry OBJECT-TYPE
SYNTAX CldCountryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in cldCountryTable. There is an
entry in this table for each country available at
the agent, as identified by a value of cldCountryCode.
Each entry also displays the corresponding channels
supported by the cldCountryCode.
All entries are added by the controller at startup."
INDEX { cldCountryCode }
::= { cldCountryTable 1 }
CldCountryEntry ::= SEQUENCE {
cldCountryCode SnmpAdminString,
cldCountryName SnmpAdminString,
cldCountryDot11aChannels SnmpAdminString,
cldCountryDot11bChannels SnmpAdminString,
cldCountryDot11aDcaChannels SnmpAdminString,
cldCountryDot11bDcaChannels SnmpAdminString,
cldCountryDot116GHzChannels SnmpAdminString,
cldCountryDot116GHzDcaChannels SnmpAdminString
}
cldCountryCode OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..255))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the country for this entry.
The 3 letter country code for this index."
::= { cldCountryEntry 1 }
cldCountryName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the name of the country for
this entry."
::= { cldCountryEntry 2 }
cldCountryDot11aChannels OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 802.11a channels
separated by comma."
::= { cldCountryEntry 3 }
cldCountryDot11bChannels OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 802.11b channels
separated by comma."
::= { cldCountryEntry 4 }
cldCountryDot11aDcaChannels OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 802.11a DCA channels
separated by comma."
::= { cldCountryEntry 5 }
cldCountryDot11bDcaChannels OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 802.11b DCA channels
separated by comma."
::= { cldCountryEntry 6 }
cldCountryDot116GHzChannels OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 802.11 6GHz channels
separated by comma."
::= { cldCountryEntry 7 }
cldCountryDot116GHzDcaChannels OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the 802.11 6GHz DCA channels
separated by comma."
::= { cldCountryEntry 8 }
-- ********************************************************************
-- Table for Configured enum Country codes
-- ********************************************************************
cldConfiguredCountryTable OBJECT-TYPE
SYNTAX SEQUENCE OF CldConfiguredCountryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the list of all configured
countries on the wlc."
::= { cldConfig 19 }
cldConfiguredCountryEntry OBJECT-TYPE
SYNTAX CldConfiguredCountryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row in cldConfiguredCountryTable.
Each entry in this table corresponds to a country
configured on wlc which is identified by cldConfiguredCountryCode.
Entries can be added/deleted by explicit management actions by
NMS or by user console."
INDEX { cldConfiguredCountryCode }
::= { cldConfiguredCountryTable 1 }
CldConfiguredCountryEntry ::= SEQUENCE {
cldConfiguredCountryCode Unsigned32,
cldConfiguredCountryRowStatus RowStatus
}
cldConfiguredCountryCode OBJECT-TYPE
SYNTAX Unsigned32 (1..252)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the country configured on the wlc."
::= { cldConfiguredCountryEntry 1 }
cldConfiguredCountryRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the row to be added or
deleted in this table."
::= { cldConfiguredCountryEntry 2 }
-- ********************************************************************
-- * NOTIFICATION Control objects
-- ********************************************************************
cldCountryChangeNotifEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to control the generation of
ciscoLwappDot11CountryChangeNotif notification.
A value of 'true' indicates that the agent generates
ciscoLwappDot11CountryChangeNotif notification.
A value of 'false' indicates that the agent doesn't
generate ciscoLwappDot11CountryChangeNotif
notification."
DEFVAL { true }
::= { cldConfig 7 }
-- ********************************************************************
-- Country Notifications
-- ********************************************************************
ciscoLwappDot11CountryChangeNotif NOTIFICATION-TYPE
OBJECTS { cldMultipleCountryCode }
STATUS current
DESCRIPTION
"This notification is generated by the controller when the
country of operation of 802.11 networks is changed
by the administrator. The new country code will be sent in
this notification."
::= { ciscoLwappDot11MIBNotifs 1 }
-- ********************************************************************
-- * Units of conformance
-- ********************************************************************
ciscoLwappDot11MIBCompliances OBJECT IDENTIFIER
::= { ciscoLwappDot11MIBConform 1 }
ciscoLwappDot11MIBGroups OBJECT IDENTIFIER
::= { ciscoLwappDot11MIBConform 2 }
-- STATUS deprecated by ciscoLwappDot11MIBComplianceRev1
ciscoLwappDot11MIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappDot11MIB module."
MODULE -- this module
MANDATORY-GROUPS { ciscoLwappDot11MIBMacOperGroup }
::= { ciscoLwappDot11MIBCompliances 1 }
-- Added since last MIB approval
ciscoLwappDot11MIBComplianceRev1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappDot11MIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappDot11MIBMacOperGroup,
ciscoLwappDot11MIBConfigGroup,
ciscoLwappDot11MIBNotifsGroup,
ciscoLwappDot11MIBStatusGroup
}
::= { ciscoLwappDot11MIBCompliances 2 }
ciscoLwappDot11MIBMacOperGroup OBJECT-GROUP
OBJECTS {
cldHtDot11nChannelBandwidth,
cldHtDot11nRifsEnable,
cldHtDot11nAmsduEnable,
cldHtDot11nAmpduEnable,
cldHtDot11nGuardIntervalEnable
}
STATUS current
DESCRIPTION
"This collection of objects represents the
operational parameters at the MAC layer
for the 802.11n networks."
::= { ciscoLwappDot11MIBGroups 1 }
ciscoLwappDot11MIBConfigGroup OBJECT-GROUP
OBJECTS {
cldHtDot11nEnable,
cldMultipleCountryCode,
cldRegulatoryDomain,
cld11nMcsDataRate,
cld11nMcsSupportEnable,
cldCountryChangeNotifEnable,
cldLoadBalancingEnable,
cldLoadBalancingWindowSize,
cldLoadBalancingDenialCount,
cldBandSelectEnable,
cldBandSelectCycleCount,
cldBandSelectCycleThreshold,
cldBandSelectAgeOutSuppression,
cldBandSelectAgeOutDualBand,
cldBandSelectClientRssi,
cld11nMcsChannelWidth,
cld11nMcsGuardInterval,
cld11nMcsModulation,
cldVhtDot11acEnable,
cld11acMcsSupportEnable,
cldLoadBalancingTrafficThreshold,
cldDot11axEnable,
cld11axMcsSupportEnable,
cld11axMbssidCap,
cld11axBssColorState,
cldConfiguredCountryCode,
cldConfiguredCountryRowStatus,
cld11axObssPdEnable,
cld11axNonSrgObssPdMax,
cld11axSrgObssPdEnable,
cld11axSrgObssPdMin,
cld11axSrgObssPdMax
}
STATUS current
DESCRIPTION
"This collection of objects specifies the configuration
parameters of 802.11i networks."
::= { ciscoLwappDot11MIBGroups 2 }
ciscoLwappDot11MIBNotifsGroup NOTIFICATION-GROUP
NOTIFICATIONS { ciscoLwappDot11CountryChangeNotif }
STATUS current
DESCRIPTION
"This collection of objects specifies the
notifications generated by the controller."
::= { ciscoLwappDot11MIBGroups 3 }
ciscoLwappDot11MIBStatusGroup OBJECT-GROUP
OBJECTS {
cldCountryName,
cldCountryDot11aChannels,
cldCountryDot11bChannels,
cldCountryDot11aDcaChannels,
cldCountryDot11bDcaChannels
}
STATUS current
DESCRIPTION
"This collection of objects specifies the
notification objects for 802.11."
::= { ciscoLwappDot11MIBGroups 4 }
-- ***********************************************************
-- 11be CONFIGURATION
-- ***********************************************************
cld11beMcsTable OBJECT-TYPE
SYNTAX SEQUENCE OF Cld11beMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the operational parameters
at the MAC layer for the 802.11be networks managed
through the controller. An agent adds an entry to
this table for every 802.11be band on startup."
::= { cldConfig 24 }
cld11beMcsEntry OBJECT-TYPE
SYNTAX Cld11beMcsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the configurational parameters
of 802.11be networks."
INDEX { cldDot11beBand,
cld11beMcsSpatialStreamIndex,
cld11beMcsDataRateIndex
}
::= { cld11beMcsTable 1 }
Cld11beMcsEntry ::= SEQUENCE {
cldDot11beBand CLDot11Band,
cld11beMcsSpatialStreamIndex Unsigned32,
cld11beMcsDataRateIndex Unsigned32,
cld11beMcsSupportEnable TruthValue
}
cldDot11beBand OBJECT-TYPE
SYNTAX CLDot11Band
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the 802.11be band the parameters
correspond to."
::= { cld11beMcsEntry 1 }
cld11beMcsSpatialStreamIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The object represents the spatial stream number
related to 802.11be MCS data rate index for a
particular band"
::= { cld11beMcsEntry 2 }
cld11beMcsDataRateIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the 802.11be MCS data
rate index for a particular band"
::= { cld11beMcsEntry 3 }
cld11beMcsSupportEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies a option to enable or disable
the 802.11be MCS data rate.
A value of 'true' indicates the MCS support is enabled.
A value of 'false' indicates the MCS support is disabled."
DEFVAL { true }
::= { cld11beMcsEntry 4 }
END
View Git Blame Copy Permalink