8046 lines
306 KiB
Plaintext
8046 lines
306 KiB
Plaintext
-- *****************************************************************
|
||
-- AWCVX-MIB.my: Cisco Aironet Wireless LAN Access Point MIB file
|
||
--
|
||
-- October 2002, Victor Griswold
|
||
--
|
||
-- Copyright (c) 2002-2003 by Cisco Systems, Inc.
|
||
-- All rights reserved.
|
||
-- *****************************************************************
|
||
--
|
||
-- ********************************************************************
|
||
-- * awcVx Management Information Base
|
||
-- ********************************************************************
|
||
|
||
AWCVX-MIB DEFINITIONS ::= BEGIN
|
||
|
||
IMPORTS
|
||
MODULE-IDENTITY,
|
||
OBJECT-TYPE,
|
||
NOTIFICATION-TYPE,
|
||
enterprises,
|
||
Integer32,
|
||
Counter32,
|
||
IpAddress,
|
||
Unsigned32
|
||
FROM SNMPv2-SMI
|
||
dot1dTpPort
|
||
FROM BRIDGE-MIB
|
||
MODULE-COMPLIANCE,
|
||
NOTIFICATION-GROUP,
|
||
OBJECT-GROUP
|
||
FROM SNMPv2-CONF
|
||
TEXTUAL-CONVENTION,
|
||
DisplayString,
|
||
RowStatus,
|
||
MacAddress,
|
||
TruthValue
|
||
FROM SNMPv2-TC
|
||
ifIndex
|
||
FROM RFC1213-MIB;
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * MODULE IDENTITY
|
||
-- ********************************************************************
|
||
awcVx MODULE-IDENTITY
|
||
LAST-UPDATED "200304210000Z"
|
||
ORGANIZATION "Cisco Systems, Inc."
|
||
CONTACT-INFO
|
||
" Cisco Systems
|
||
Customer Service
|
||
|
||
Postal: 170 W Tasman Drive
|
||
San Jose, CA 95134
|
||
USA
|
||
|
||
Tel: +1 800 553-NETS
|
||
|
||
E-mail: cs-aironet@cisco.com"
|
||
DESCRIPTION
|
||
"The MIB module for Aironet entities.
|
||
iso(1).org(3).dod(6).internet(1).private(4).
|
||
enterprises(1).aironet(522).awcVx(3).
|
||
|
||
This MIB provides network management
|
||
support for Cisco IEEE 802.11 Wireless LAN
|
||
type devices such as Access Point and Wireless
|
||
Access Bridge."
|
||
|
||
REVISION "200304210000Z"
|
||
DESCRIPTION
|
||
"Added awcDot11NonRootMobility to determine if a
|
||
radio should look for a better parent AP in heavy
|
||
traffic and awcFtEnableMcastMapping for multicast
|
||
forwarding configuration."
|
||
REVISION "200212030000Z"
|
||
DESCRIPTION
|
||
"This revision adds awcDot11QoSTable QoS support,
|
||
awcIfOutDiscardsCoSx statistics to awcIfTable,
|
||
awcPolGrpTable policy group, 802.11A 5GHz radio
|
||
support, and action when Ethernet is lost. Corrected
|
||
the ranges for awcDot11AuthenticationAlgorithmsIndex
|
||
and awcPolGrpId."
|
||
::= { enterprises 522 3 }
|
||
|
||
aironet OBJECT IDENTIFIER ::= { enterprises 522 }
|
||
|
||
-- ********************************************************************
|
||
-- * Major sections
|
||
-- ********************************************************************
|
||
-- Aironet Wireless Communications System (awcSystem) Attributes
|
||
-- DEFINED AS "The awcSystem object class provides all
|
||
-- standard information to support operation of an Aironet
|
||
-- Access Point such as versions, system flags, and what
|
||
-- features are enabled.";
|
||
|
||
awcSystem OBJECT IDENTIFIER ::= {awcVx 1}
|
||
|
||
-- bootconfig VxWorks (bootconfigVx) Attributes
|
||
-- DEFINED AS "The bootconfigVx object class provides all
|
||
-- standard information to support operation of the boot
|
||
-- server.";
|
||
|
||
bootconfigVx OBJECT IDENTIFIER ::= {awcVx 2}
|
||
|
||
-- Aironet Wireless Communication Serial Device (awcSerialDev)
|
||
-- Attributes DEFINED AS "The awcSerialDev object class
|
||
-- provides all standard information to support configuration
|
||
-- of serial ports.";
|
||
|
||
awcSerialDev OBJECT IDENTIFIER ::= {awcVx 3}
|
||
|
||
-- Aironet Wireless Communication FTP (awcFtp) Attributes
|
||
-- DEFINED AS "The awcFTP object class provides all standard
|
||
-- information to support configuration of the FTP protocol.";
|
||
|
||
awcFtp OBJECT IDENTIFIER ::= {awcVx 4}
|
||
|
||
-- Aironet Wireless Communication 802.11 (awc802dot11) Attributes
|
||
-- DEFINED AS "The awc802dot11 object class provides all
|
||
-- standard information to support configuration of the 802.11
|
||
-- protocol. This class also provides various statistics of
|
||
-- 802.11 stations.";
|
||
|
||
awc802dot11 OBJECT IDENTIFIER ::= {awcVx 6}
|
||
|
||
-- Aironet Wireless Communication UserManager (awcUserMgr) Attributes
|
||
-- DEFINED AS "The awcUserMgr object class provides all
|
||
-- standard information to support configuration of the User
|
||
-- Manager.";
|
||
|
||
awcUserMgr OBJECT IDENTIFIER ::= {awcVx 7}
|
||
|
||
-- Aironet Wireless Communication HTTPd (awcHttpd) Attributes
|
||
-- DEFINED AS "The awcHttpd object class provides all standard
|
||
-- information to support configuration of the Web Server.";
|
||
|
||
awcHttpd OBJECT IDENTIFIER ::= {awcVx 8}
|
||
|
||
-- Aironet Wireless Communication DNS Resolver (awcDnsRes) Attributes
|
||
-- DEFINED AS "The awcDnsRes object class provides all
|
||
-- standard information to support configuration of the DNS
|
||
-- Resolver.";
|
||
|
||
awcDnsRes OBJECT IDENTIFIER ::= {awcVx 9}
|
||
|
||
-- Aironet Wireless Communication SNMP (awcSnmp) Attributes
|
||
-- DEFINED AS "The awcSnmp object class provides all standard
|
||
-- information to support configuration of the SNMP
|
||
-- protocol.";
|
||
|
||
awcSnmp OBJECT IDENTIFIER ::= {awcVx 10}
|
||
|
||
-- Aironet Wireless Communication SNTP (awcSntp) Attributes
|
||
-- DEFINED AS "The awcSntp object class provides all standard
|
||
-- information to support configuration of the SNTP
|
||
-- protocol.";
|
||
|
||
awcSntp OBJECT IDENTIFIER ::= {awcVx 11}
|
||
|
||
-- Aironet Wireless Communication Forwarding Table (awcForwardTbl)
|
||
-- Attributes
|
||
-- DEFINED AS "The awcForwardTbl object class provides all
|
||
-- standard information to support configuration of the
|
||
-- Forwarding Table.";
|
||
|
||
awcForwardTbl OBJECT IDENTIFIER ::= {awcVx 12}
|
||
|
||
-- Aironet Wireless Communication RIP (awcRipConfig) Attributes
|
||
-- DEFINED AS "The awcRipConfig object class provides all
|
||
-- standard information to support configuration of the RIP
|
||
-- Protocol.";
|
||
|
||
awcRipConfig OBJECT IDENTIFIER ::= {awcVx 13}
|
||
|
||
-- Aironet Wireless Communications Event Log (awcEventLog) Attributes
|
||
-- DEFINED AS "The awcEventLog object class provides all
|
||
-- standard information to support operation of the Event
|
||
-- Log.";
|
||
|
||
awcEventLog OBJECT IDENTIFIER ::= {awcVx 14}
|
||
|
||
-- Aironet Wireless Communications Ethernet Controller (awcEtherMIB)
|
||
-- Attributes
|
||
-- DEFINED AS "The awcEtherMIB object class provides all
|
||
-- standard information to support operation of the Ethernet
|
||
-- Controller.";
|
||
|
||
awcEtherMIB OBJECT IDENTIFIER ::= {awcVx 15}
|
||
|
||
-- Aironet Wireless Communications Policy Groups (awcPolicyGroups)
|
||
-- Attributes
|
||
-- DEFINED AS "The awcPolicyGroups object class provides all
|
||
-- standard information to support specification of named
|
||
-- groups of related protocol filters.";
|
||
|
||
awcPolicyGroups OBJECT IDENTIFIER ::= {awcVx 16}
|
||
|
||
-- Aironet Wireless Communications DDP/IAPP (awcDdpIAPP) Attributes
|
||
-- DEFINED AS "The awcDdpIAPP object class provides all
|
||
-- standard information to support operation of the DDP and
|
||
-- IAPP protocols.";
|
||
|
||
awcDdpIAPP OBJECT IDENTIFIER ::= {awcVx 17}
|
||
|
||
-- Aironet Wireless Communications Hot Standby (awcHotStandby)
|
||
-- Attributes
|
||
-- DEFINED AS "The awcHotStandby object class provides all
|
||
-- standard information to support operation of an AP in the
|
||
-- Hot Standby mode.";
|
||
|
||
awcHotStandby OBJECT IDENTIFIER ::= {awcVx 18}
|
||
|
||
-- Aironet Wireless Communications Authentication, Authorization, and
|
||
-- Accounting (awcAaa) Attributes .
|
||
-- DEFINED AS "The awcAaa object class provides all standard
|
||
-- information to support configuration of RADIUS and TACACS+
|
||
-- client operation.";
|
||
|
||
awcAaa OBJECT IDENTIFIER ::= {awcVx 19}
|
||
|
||
-- Aironet Wireless Communications Authentication, Authorization, and
|
||
-- Accounting (awcAaa)'s accounting configuration
|
||
-- DEFINED AS "The awcAcctConfig object provides all the
|
||
-- configuration for accounting.";
|
||
|
||
awcAcctConfig OBJECT IDENTIFIER ::= { awcAaa 3 }
|
||
|
||
-- Aironet Wireless Communications Protocol Filters
|
||
-- (awcProtocolFilters) Attributes
|
||
-- DEFINED AS "The awcProtocolFilters object class provides
|
||
-- all standard information to support configuration of static
|
||
-- protocol filters on the AP.";
|
||
|
||
awcProtocolFilters OBJECT IDENTIFIER ::= {awcVx 20}
|
||
|
||
-- Aironet Wireless Communications Mobile IP
|
||
-- (awcMobileIP) Attributes
|
||
-- DEFINED AS "The awcMobileIP object class provides
|
||
-- all standard information to support configuration of proxy
|
||
-- mobileIP on the AP.";
|
||
|
||
awcMobileIP OBJECT IDENTIFIER ::= {awcVx 22}
|
||
|
||
-- Aironet Wireless Communications Experimental (awcExperimental)
|
||
-- Attributes
|
||
-- DEFINED AS "The awcExperimental object class provides all
|
||
-- standard information to support experimental functions.";
|
||
|
||
-- awcExperimental OBJECT IDENTIFIER ::= {awcVx 99}
|
||
|
||
-- ********************************************************************
|
||
-- * MIB attribute OBJECT-TYPE definitions follow
|
||
-- ********************************************************************
|
||
|
||
AwcVlanId ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A 12-bit VLAN ID used in the VLAN Tag header. A value
|
||
of 0 indicates NULL or no VLAN ID."
|
||
SYNTAX INTEGER (0..4094)
|
||
|
||
AwcPolId ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A 10-bit Policy Group identifier. A value
|
||
of 0 indicates that no Policy Group is specified."
|
||
SYNTAX INTEGER (0..1023)
|
||
|
||
WEPKeytype128 ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Wired Equivalent Privacy (WEP) shared secret
|
||
encryption key, 128-bits."
|
||
SYNTAX OCTET STRING (SIZE (5..13))
|
||
|
||
AwcInvokeCommand ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Command directive to control asynchronous operations
|
||
on the host system of the SNMP agent. Not all
|
||
asynchronous operations support all directives. For
|
||
example, not all operations support 'restart' or
|
||
'restartNotify' commands.
|
||
|
||
inactive - No operation is either started or
|
||
in progress.
|
||
start - Start the operation. Perform the
|
||
operation to completion.
|
||
startNotify - Start the operation. Perform the
|
||
operation to completion, then
|
||
notify the requesting SNMP Manager
|
||
via a Trap.
|
||
restart - If the operation is not already
|
||
started, start it. If it is already
|
||
started, re-initialize the operation
|
||
in a graceful manner and start it
|
||
over again. Do not alter the Notify
|
||
option of the corresponding Start
|
||
command.
|
||
restartNotify - If the operation is not already
|
||
started, start it. If it is
|
||
already started, re-initialize the
|
||
operation in a graceful manner and
|
||
start it over again. When the
|
||
operation is complete, notify the
|
||
requesting SNMP Manager via a Trap.
|
||
cancel - If the operation, is not started, do
|
||
nothing. If it is started, stop the
|
||
operation gracefully. Notify the SNMP
|
||
Manager via a Trap in accordance with
|
||
whether {Re}Start or {Re}StartNotify
|
||
was used.
|
||
|
||
Multiple use of 'start' before an operation completes
|
||
is ignored. Multiple use of 'startNotify' before an
|
||
operation completes adds the Notify option of the
|
||
operation."
|
||
SYNTAX INTEGER { inactive(1),
|
||
start(2),
|
||
startNotify(3),
|
||
restart(4),
|
||
restartNotify(5),
|
||
cancel(6) }
|
||
|
||
|
||
AwcDot11MicAlgorithm ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Auxiliary Message Integrity Check (MIC) calculated
|
||
on WEP-encoded packets to validate that they have
|
||
not been modified. This is in addition to the
|
||
standard 802.11 ICV."
|
||
SYNTAX INTEGER { micNone(1),
|
||
micMMH(2) }
|
||
|
||
|
||
AwcDot11WEPKeyPermuteAlgorithm ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Function through which the WEP encryption key is
|
||
permuted between key renewal periods."
|
||
SYNTAX INTEGER { wepPermuteNone(1),
|
||
wepPermuteIV(2) }
|
||
|
||
|
||
AwcEventDisposition ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specifies the manner in which an event should be
|
||
handled by the system. Events can be counted,
|
||
displayed on the console, recorded in the system's
|
||
event log memory, or an external device can be
|
||
notified of the event. Each degree of handling
|
||
implies all lower degrees."
|
||
SYNTAX INTEGER { count(1),
|
||
displayConsole(2),
|
||
record(3),
|
||
notify(4) }
|
||
|
||
|
||
AwcDot11EventDisposition ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specifies options to handled standard IEEE 802.11 traps
|
||
on this system"
|
||
SYNTAX INTEGER { noNotification(1),
|
||
eventLogOnly(2),
|
||
ieeeTrapOnly(3),
|
||
eventLogAndIeeeTrap(4) }
|
||
|
||
|
||
AwcHotStandbyStatus ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The status of the hot standby access point:
|
||
normal(0) - AP hot standby is running.
|
||
initializing(1) - AP hot standby is
|
||
being initialized.
|
||
takeover(2) - AP takeovers as new
|
||
active access point.
|
||
stopped(3) - AP hot standby stopped.
|
||
associating(4) - Standby AP associates to
|
||
active access point.
|
||
rootMacFailed(5) - Cannot detect root AP
|
||
MAC address.
|
||
interfaceMerge(6) - Interface merge.
|
||
associationFail(7) - Association failed.
|
||
etherTestFail(8) - Hot standby test on
|
||
Ethernet failed.
|
||
radioTestFail(9) - Hot standby test on
|
||
radio failed.
|
||
error(10) - Hot standby system error."
|
||
SYNTAX INTEGER { normal(0),
|
||
initializing(1),
|
||
takeover(2),
|
||
stopped(3),
|
||
associating(4),
|
||
rootMacFailed(5),
|
||
interfaceMerge(6),
|
||
associationFail(7),
|
||
etherTestFail(8),
|
||
radioTestFail(9),
|
||
error(10) }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcSystem parameters
|
||
-- ********************************************************************
|
||
vxWorksVersion OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The version of the underlying VxWorks
|
||
operating system."
|
||
::= { awcSystem 1 }
|
||
|
||
creationDate OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The date and time the Access Point system code
|
||
was initially compiled."
|
||
::= { awcSystem 2 }
|
||
|
||
awcVxVersion OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The version of the Access Point system code."
|
||
::= { awcSystem 3 }
|
||
|
||
sysFlags OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The VxWorks sysFlags system-configuration
|
||
flags in use by the Access Point system. Not
|
||
used by system code with awcVxVersion from
|
||
10.00 to 11.06."
|
||
DEFVAL { 192 }
|
||
::= { awcSystem 4 }
|
||
|
||
languageCode OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The language currently in use by the system.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "en-US" }
|
||
::= { awcSystem 5 }
|
||
|
||
awcDevID OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Aironet DDP protocol device ID of the
|
||
system when using the full capabilities
|
||
with which the system is licensed. Note
|
||
that a system may be configured to use
|
||
fewer capabilities that those for which
|
||
it is licensed. For example, a Bridge
|
||
may be configured for use as an Access Point."
|
||
::= { awcSystem 6 }
|
||
|
||
awcDevIDtxt OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Textual representation of awcDevID.
|
||
Max. string length is 128 octets."
|
||
::= { awcSystem 7 }
|
||
|
||
enableHTTP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point's HTTP server
|
||
can accept connections from other network
|
||
devices. If false, the Access Point's HTTP
|
||
server will only accept connections from the
|
||
Access Point's console or indirectly over
|
||
TELNET."
|
||
DEFVAL { true }
|
||
::= { awcSystem 8 }
|
||
|
||
enableTelnet OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point's TELNET server
|
||
can accept connections from other network
|
||
devices. If false, all TELNET connections
|
||
will be refused."
|
||
DEFVAL { true }
|
||
::= { awcSystem 9 }
|
||
|
||
enableSNMP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point's SNMP agent can
|
||
accept connections from other network
|
||
devices. If false, all SNMP connections
|
||
will be refused. Note that this can only
|
||
be set to false by an SNMP management
|
||
station. If false, it can only be set to true
|
||
by non-SNMP means."
|
||
DEFVAL { false }
|
||
::= { awcSystem 10 }
|
||
|
||
enableDnsResolver OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point will attempt to
|
||
resolve IP address references through all
|
||
configured DNS servers and will attempt to
|
||
perform reverse-lookup via all configured
|
||
DNS servers when displaying IP addresses.
|
||
If false, the Access Point will interpret
|
||
and display only explicit numeric IP
|
||
addresses."
|
||
DEFVAL { true }
|
||
::= { awcSystem 11 }
|
||
|
||
enableSNTP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point will attempt to
|
||
periodically update its wall-clock time via a
|
||
configured SNTP server. If false, the Access
|
||
Point wall-clock time must be manually
|
||
adjusted."
|
||
DEFVAL { false }
|
||
::= { awcSystem 13 }
|
||
|
||
enableWDB OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point will enable use of
|
||
the VxWorks WDB debugger upon its next reboot.
|
||
If false, no WDB debugging services will be
|
||
available after the next reboot. The value
|
||
of enableWDB is applicable only to special
|
||
diagnostic versions of the Access Point
|
||
system code."
|
||
DEFVAL { false }
|
||
::= { awcSystem 14 }
|
||
|
||
pingTxLen OBJECT-TYPE
|
||
SYNTAX Unsigned32 (12..4096)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The size in octets of ping packets transmitted
|
||
by the Access Point. Default 64."
|
||
DEFVAL { 64 }
|
||
::= { awcSystem 15 }
|
||
|
||
awcFirstBoot OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, no user-specified configuration has
|
||
been saved by the Access Point since either
|
||
the system left Cisco manufacturing or since
|
||
the user performed a Reset All System Factory
|
||
Defaults operation. If false, a change in
|
||
configuration has been saved by the user.
|
||
Note that configurations specified solely via
|
||
boot protocols such as DHCP or BOOTP are not
|
||
considered user-specified for purposes of
|
||
changing awcFirstBoot."
|
||
DEFVAL { true }
|
||
::= { awcSystem 16 }
|
||
|
||
awcOemOUI OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IEEE Organizationally Unique Identifier of
|
||
the reseller for which this system is
|
||
branded."
|
||
::= { awcSystem 17 }
|
||
|
||
awcOemName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The full name of the reseller for which this
|
||
system is branded."
|
||
::= { awcSystem 18 }
|
||
|
||
awcOemNameShort OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An abbreviated name of the reseller for which
|
||
this system is branded."
|
||
::= { awcSystem 19 }
|
||
|
||
awcOemHomeURL OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The URL of the corporate HTML home page of the
|
||
reseller for which this system is branded."
|
||
::= { awcSystem 20 }
|
||
|
||
enablePSPF OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, Publicly-Secure Packet Forwarding
|
||
mode is enabled (i.e. clients can not
|
||
communicate with each other). If false,
|
||
normal packet forwarding is used."
|
||
DEFVAL { false }
|
||
::= { awcSystem 21 }
|
||
|
||
sysExceptionReboot OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, all access violations or other
|
||
general faults in any task will result in a
|
||
reboot of the system. If false, such errors
|
||
will not result in a reboot, and thus
|
||
diagnostics can be performed on the system."
|
||
DEFVAL { true }
|
||
::= { awcSystem 24 }
|
||
|
||
bootblockVersion OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The version of the Access Point boot block
|
||
(bootstrap loader) code."
|
||
::= { awcSystem 25 }
|
||
|
||
motherboardRevision OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Revision number of the Access Point
|
||
system motherboard."
|
||
::= { awcSystem 26 }
|
||
|
||
enableSTP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true and the system is licensed with Bridge
|
||
capabilities, the IEEE 802.1D Spanning Tree
|
||
Protocol will be be used to control packet
|
||
forwarding on all network interfaces. If
|
||
false or the system is not licensed with
|
||
Bridge capabilities, the system will use
|
||
Access Point heuristics to control packet
|
||
forwarding on all network interfaces."
|
||
::= { awcSystem 27 }
|
||
|
||
enableRebootKey OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the VxWorks Monitor Trap keystroke
|
||
is enabled from the console and from Telnet.
|
||
By default, this is <control-X>. Entering
|
||
this character initiates a warm-restart of
|
||
the system. If false, the VxWorks Monitor
|
||
Trap keystroke is disabled."
|
||
DEFVAL { false }
|
||
::= { awcSystem 28 }
|
||
|
||
awcLocateUnit OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the unit will immediately begin
|
||
flashing all three of its Status LEDs with
|
||
an alternating pattern of amber and off.
|
||
If false, the Status LEDs operate in their
|
||
normal fashion."
|
||
DEFVAL { false }
|
||
::= { awcSystem 29 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcSystem parameters
|
||
-- ********************************************************************
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * bootconfigVx parameters
|
||
-- ********************************************************************
|
||
bootconfigBootProtocol OBJECT-TYPE
|
||
SYNTAX INTEGER {none(1), bootp(2), dhcp(3)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The protocol to be used for automatic
|
||
configuration at the time of system
|
||
bootstrap/reboot. Options BOOTP, DHCP,
|
||
or none."
|
||
DEFVAL { dhcp }
|
||
::= { bootconfigVx 1 }
|
||
|
||
bootconfigReadINI OBJECT-TYPE
|
||
SYNTAX INTEGER {always(1), never(2), ifSpecified(3)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If always, the system will attempt to read a
|
||
.ini-formatted configuration file upon every
|
||
reboot. If never, the system will not attempt
|
||
to read a .ini file upon reboot, even if a
|
||
boot protocol is in use and the boot server
|
||
specifies a file to be read. If ifSpecified,
|
||
the system will attempt to read a .ini file
|
||
upon reboot if and only if a boot protocol
|
||
is in use and the boot server explicitly
|
||
specifies a file to be read. The system
|
||
attempts several filenames in the process of
|
||
retrieving a .ini file without error. In
|
||
order, these filenames are based on the
|
||
system's BOOTP- or DHCP-assigned client name,
|
||
then the MIB2 sysName, then the system's IP
|
||
address, then, as a last resort, the BOOTP- or
|
||
DHCP-assigned boot file name. For each
|
||
filename, the system attempts to read first
|
||
from the designated defaultFileServer, then,
|
||
if not successful, from one of either the
|
||
BOOTP/DHCP server itself or
|
||
bootconfigFileServerAddr (if specified by the
|
||
BOOTP/DHCP server)."
|
||
DEFVAL { ifSpecified }
|
||
::= { bootconfigVx 2 }
|
||
|
||
bootconfigServerConfigTimeout OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The time in seconds which the system should
|
||
wait for a configuration response from a
|
||
BOOTP server before falling back to the
|
||
stored configuration."
|
||
DEFVAL { 120 }
|
||
::= { bootconfigVx 3 }
|
||
|
||
bootconfigMultOfferTimeout OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The time, in seconds, which the system should
|
||
wait for a better offer configuration response
|
||
from a DHCP or BOOTP server before choosing
|
||
the best current offer."
|
||
DEFVAL { 5 }
|
||
::= { bootconfigVx 4 }
|
||
|
||
bootconfigReqLeaseDuration OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "minutes"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The requested DHCP lease duration, in
|
||
minutes."
|
||
DEFVAL { 1440 }
|
||
::= { bootconfigVx 5 }
|
||
|
||
bootconfigMinLeaseDuration OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "minutes"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The minimum acceptable DHCP lease duration,
|
||
in minutes."
|
||
DEFVAL { 0 }
|
||
::= { bootconfigVx 6 }
|
||
|
||
bootconfigDev OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Text string identifying the network device
|
||
used for bootstrapping the system via BOOTP or
|
||
DHCP. This is only applicable in BOOTP mode
|
||
or when the system is configured as a router,
|
||
when not all the network interfaces share the
|
||
same ifPhysAddress."
|
||
::= { bootconfigVx 7 }
|
||
|
||
bootconfigClientAddr OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IPv4 network address of this device, as
|
||
determined by the BOOTP or DHCP protocol."
|
||
::= { bootconfigVx 8 }
|
||
|
||
bootconfigHostAddr OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IPv4 network address of the BOOTP or DHCP
|
||
server from which the configuration
|
||
of this device was leased."
|
||
::= { bootconfigVx 9 }
|
||
|
||
bootconfigBootFile OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Name of the default boot configuration file,
|
||
specified by the BOOTP or DHCP server,
|
||
containing the system configuration to be
|
||
utilized by this device. This is considered
|
||
a default configuration file because many
|
||
DHCP servers are not capable of distinguishing
|
||
boot files between different clients."
|
||
::= { bootconfigVx 10 }
|
||
|
||
bootconfigSubnetMask OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IPv4 network subnet mask to be used by this
|
||
device, as determined by the BOOTP or DHCP
|
||
protocol."
|
||
::= { bootconfigVx 11 }
|
||
|
||
bootconfigGateway OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IPv4 network address of the default network
|
||
gateway to be used by this device, as
|
||
determined by the BOOTP or DHCP protocol."
|
||
::= { bootconfigVx 12 }
|
||
|
||
bootconfigHostName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Textual name of the BOOTP or DHCP server from
|
||
which the configuration of this device was
|
||
leased. This should be a DNS-recognizable
|
||
host name."
|
||
::= { bootconfigVx 13 }
|
||
|
||
bootconfigClientName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Textual name of this device, as determined by
|
||
the BOOTP or DHCP protocol. This should be a
|
||
DNS-recognizable host name."
|
||
::= { bootconfigVx 14 }
|
||
|
||
bootconfigNameServerTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF BootconfigNameServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of DNS Name Servers provided by the
|
||
bootconfigHostAddr Boot Server."
|
||
::= { bootconfigVx 15 }
|
||
|
||
bootconfigNameServerEntry OBJECT-TYPE
|
||
SYNTAX BootconfigNameServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in bootconfigNameServerTable."
|
||
INDEX {bootconfigNameServerPriority}
|
||
::= { bootconfigNameServerTable 1 }
|
||
|
||
BootconfigNameServerEntry ::=
|
||
SEQUENCE {
|
||
bootconfigNameServerPriority INTEGER,
|
||
bootconfigNameServer IpAddress}
|
||
|
||
bootconfigNameServerPriority OBJECT-TYPE
|
||
SYNTAX INTEGER (1..3)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The priority order in which a domain name
|
||
server is queried. Lower values are queried
|
||
first."
|
||
::= { bootconfigNameServerEntry 1 }
|
||
|
||
bootconfigNameServer OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IPv4 address of a domain name server."
|
||
::= { bootconfigNameServerEntry 2 }
|
||
|
||
bootconfigDomainName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Name of the IP domain of which this device
|
||
is a member, as determined by the BOOTP or
|
||
DHCP protocol."
|
||
::= { bootconfigVx 16 }
|
||
|
||
bootconfigSntpServer OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IPv4 network address of SNTP server for use
|
||
by this device, as determined by the BOOTP or
|
||
DHCP protocol."
|
||
::= { bootconfigVx 17 }
|
||
|
||
bootconfigSaveServerResponse OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the leased configuration from a boot
|
||
server is saved as the new system defaults.
|
||
If false, system defaults remain unchanged
|
||
when a new configuration is leased."
|
||
DEFVAL { true }
|
||
::= { bootconfigVx 18 }
|
||
|
||
bootconfigCmdInvokeIniLoad OBJECT-TYPE
|
||
SYNTAX AwcInvokeCommand
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Initiate loading of an initialization
|
||
script '.ini' file from the file server
|
||
into the system FLASH.
|
||
|
||
Commands recognized: start."
|
||
::= { bootconfigVx 19 }
|
||
|
||
bootconfigCmdStatusIniLoad OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Status of the most recent command to load
|
||
an initialization script '.ini' file.
|
||
Possible values:
|
||
0 = Operation completed successfully (or
|
||
has not taken place).
|
||
2 = The '.ini' file was not found on the
|
||
file server.
|
||
12 = Insufficient memory to load the
|
||
'.ini' file.
|
||
22 = Invalid '.ini' file format.
|
||
35 = File format of the '.ini' file is not
|
||
supported.
|
||
68 = Operation is still in progress. Poll
|
||
again later.
|
||
72 = Operation was started, but later was
|
||
canceled."
|
||
::= { bootconfigVx 20 }
|
||
|
||
-- bootconfigCmdInvokeIniSave OBJECT-TYPE
|
||
-- SYNTAX AwcInvokeCommand
|
||
-- MAX-ACCESS read-write
|
||
-- STATUS current
|
||
-- DESCRIPTION
|
||
-- "Initiate saving of an initialization
|
||
-- script '.ini' file to the file server
|
||
-- from the system FLASH."
|
||
-- ::= { bootconfigVx 21 }
|
||
|
||
-- bootconfigCmdStatusIniSave OBJECT-TYPE
|
||
-- SYNTAX Integer32
|
||
-- MAX-ACCESS read-only
|
||
-- STATUS current
|
||
-- DESCRIPTION
|
||
-- "Status of the most recent command to save
|
||
-- the initialization script '.ini' file.
|
||
-- Possible values:
|
||
-- 0 = Operation completed successfully (or
|
||
-- has not taken place).
|
||
-- 1 = Insufficient permission to save the
|
||
-- file.
|
||
-- 2 = The '.ini' file was not found on the
|
||
-- file server.
|
||
-- 22 = Invalid '.ini' file format.
|
||
-- 68 = Operation is still in progress. Poll
|
||
-- again later.
|
||
-- 72 = Operation was started, but later was
|
||
-- canceled."
|
||
-- ::= { bootconfigVx 22 }
|
||
|
||
-- bootconfigDetailLevelIniSave OBJECT-TYPE
|
||
-- SYNTAX INTEGER
|
||
-- MAX-ACCESS read-write
|
||
-- STATUS current
|
||
-- DESCRIPTION
|
||
-- "Level of detail and line formatting for
|
||
-- the initialization script '.ini' file to
|
||
-- be saved."
|
||
-- ::= { bootconfigVx 23 }
|
||
|
||
bootconfigDhcpClassID OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specification of the DHCP Class Identifier
|
||
presented by the system when requesting DHCP
|
||
leases."
|
||
DEFVAL { "AP4800E" }
|
||
::= { bootconfigVx 24 }
|
||
|
||
bootconfigFileServerAddr OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IPv4 network address of the file server from
|
||
which to read configuration files, as
|
||
determined by the BOOTP or DHCP protocol."
|
||
::= { bootconfigVx 25 }
|
||
|
||
bootconfigLogServerAddr OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IPv4 network address of the host to receive
|
||
SYSLOG messages, as determined by the BOOTP
|
||
or DHCP protocol."
|
||
::= { bootconfigVx 26 }
|
||
|
||
bootconfigBootCount OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of times the system code has been
|
||
restarted since the system left Cisco
|
||
manufacturing."
|
||
::= { bootconfigVx 27 }
|
||
|
||
bootconfigDhcpClientIdType OBJECT-TYPE
|
||
SYNTAX INTEGER {
|
||
ethernet10Mb(1),
|
||
experimentalEthernet3Mb(2),
|
||
amateurRadioAxDot25(3),
|
||
proteonProNetTokenRing(4),
|
||
chaos(5),
|
||
ieee802Networks(6),
|
||
arcnet(7),
|
||
hyperchannel(8),
|
||
lanstar(9),
|
||
autonet(10),
|
||
localTalk(11),
|
||
localNet(12),
|
||
nonHardware(128)
|
||
}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The ARP hardware type, per RFC 1700, of
|
||
bootconfigDhcpClientIdValue. If it is not
|
||
a hardware address (e.g. is a fully-qualified
|
||
domain name), a value of 0 will be used for
|
||
the DHCP Client Identifier 'htype' field."
|
||
::= { bootconfigVx 28 }
|
||
|
||
bootconfigDhcpClientIdValue OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specification of the DHCP unique client Identifier
|
||
presented by the system when requesting DHCP
|
||
leases."
|
||
::= { bootconfigVx 29 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of bootconfigVx parameters
|
||
-- ********************************************************************
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcSerialDev parameters
|
||
-- ********************************************************************
|
||
awcSerialConfigTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcSerialConfigEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"SerialConfigTable attributes. In tabular form
|
||
to allow for multiple instances on an agent."
|
||
::= { awcSerialDev 1 }
|
||
|
||
awcSerialConfigEntry OBJECT-TYPE
|
||
SYNTAX AwcSerialConfigEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcSerialConfigEntry table."
|
||
INDEX {serialDevIndex}
|
||
::= { awcSerialConfigTable 1 }
|
||
|
||
AwcSerialConfigEntry ::=
|
||
SEQUENCE {
|
||
serialDevIndex Integer32,
|
||
serialAdminStatus INTEGER,
|
||
serialOperStatus INTEGER,
|
||
serialBaud Unsigned32,
|
||
serialParity INTEGER,
|
||
serialDataBits Unsigned32,
|
||
serialStopBits Unsigned32,
|
||
serialFlowControl INTEGER,
|
||
serialTerminalType INTEGER,
|
||
serialTerminalLines Unsigned32,
|
||
serialTerminalColumns Unsigned32,
|
||
serialDevFd Integer32
|
||
}
|
||
|
||
serialDevIndex OBJECT-TYPE
|
||
SYNTAX Integer32 (1..2)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The index used to access rows in the
|
||
awcSerialConfig table."
|
||
::= { awcSerialConfigEntry 1 }
|
||
|
||
serialAdminStatus OBJECT-TYPE
|
||
SYNTAX INTEGER {up(1), down(2), testing(3), error(4)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The requested status of the serial port."
|
||
DEFVAL { up }
|
||
::= { awcSerialConfigEntry 2 }
|
||
|
||
serialOperStatus OBJECT-TYPE
|
||
SYNTAX INTEGER {up(1), down(2), testing(3), error(4)}
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The actual status of the serial port."
|
||
::= { awcSerialConfigEntry 3 }
|
||
|
||
serialBaud OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The baud rate of the serial port."
|
||
DEFVAL { 9600 }
|
||
::= { awcSerialConfigEntry 4 }
|
||
|
||
serialParity OBJECT-TYPE
|
||
SYNTAX INTEGER {none(1), even(2), odd(3), one(4),
|
||
zero(5)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The parity of the serial port."
|
||
DEFVAL { none }
|
||
::= { awcSerialConfigEntry 5 }
|
||
|
||
serialDataBits OBJECT-TYPE
|
||
SYNTAX Unsigned32 (7..8)
|
||
UNITS "bits"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of data bits per character
|
||
recognized by the serial port."
|
||
DEFVAL { 8 }
|
||
::= { awcSerialConfigEntry 6 }
|
||
|
||
serialStopBits OBJECT-TYPE
|
||
SYNTAX Unsigned32 (1..2)
|
||
UNITS "bits"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of stop bits of the serial port."
|
||
DEFVAL { 1 }
|
||
::= { awcSerialConfigEntry 7 }
|
||
|
||
serialFlowControl OBJECT-TYPE
|
||
SYNTAX INTEGER {none(1), swXonXoff(2), hwRtsCts(3),
|
||
swHwBoth(4)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The flow control method used by the serial
|
||
port."
|
||
DEFVAL { swXonXoff }
|
||
::= { awcSerialConfigEntry 8 }
|
||
|
||
serialTerminalType OBJECT-TYPE
|
||
SYNTAX INTEGER {teletype(1), ansi(2)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The terminal type of the serial port."
|
||
DEFVAL { teletype }
|
||
::= { awcSerialConfigEntry 9 }
|
||
|
||
serialTerminalLines OBJECT-TYPE
|
||
SYNTAX Unsigned32 (16..50)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of horizontal lines available on
|
||
each terminal page. Default 24."
|
||
DEFVAL { 24 }
|
||
::= { awcSerialConfigEntry 10 }
|
||
|
||
serialTerminalColumns OBJECT-TYPE
|
||
SYNTAX Unsigned32 (64..132)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of vertical columns available on
|
||
each terminal page. Default 80."
|
||
DEFVAL { 80 }
|
||
::= { awcSerialConfigEntry 11 }
|
||
|
||
serialDevFd OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The VxWorks I/O File Descriptor used to access
|
||
the serial device."
|
||
::= { awcSerialConfigEntry 12 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcSerialDev parameters
|
||
-- ********************************************************************
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcFtp parameters
|
||
-- ********************************************************************
|
||
defaultFileServer OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of the preferred file server to be
|
||
used for all FTP and TFTP Put and Get
|
||
operations. Max. name length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 1 }
|
||
|
||
awcFileXferProtocol OBJECT-TYPE
|
||
SYNTAX INTEGER {tftp(1), ftp(2)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The protocol to be used by the system for file
|
||
transfer (TFTP or FTP)."
|
||
DEFVAL { ftp }
|
||
::= { awcFtp 2 }
|
||
|
||
awcFileXferUser OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of the user, as required by all FTP
|
||
file transfers. Max. name length is 128
|
||
octets."
|
||
DEFVAL { "anonymous" }
|
||
::= { awcFtp 3 }
|
||
|
||
awcFileXferPassword OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The password of the user, as required by all
|
||
FTP file transfers. Max. password length is
|
||
128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 4 }
|
||
|
||
awcFileXferCmdInvokeFileLoad OBJECT-TYPE
|
||
SYNTAX AwcInvokeCommand
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Initiate loading of all specified files
|
||
from the file server into the system
|
||
FLASH.
|
||
|
||
Commands recognized: start."
|
||
::= { awcFtp 5 }
|
||
|
||
awcFileXferCmdStatusFileLoad OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Status of the most recent command to load
|
||
the specified fileXferFile* files.
|
||
Possible values:
|
||
0 = Operation completed successfully
|
||
(or has not taken place).
|
||
2 = At least one file was not found on
|
||
the file server.
|
||
12 = Insufficient memory to load all
|
||
files.
|
||
22 = No file specified, or invalid file
|
||
format.
|
||
35 = File format of at least one of the
|
||
files is not supported.
|
||
68 = Operation is still in progress.
|
||
Poll again later.
|
||
72 = Operation was started, but later was
|
||
canceled."
|
||
::= { awcFtp 6 }
|
||
|
||
awcFileXferCmdInvokeFileSave OBJECT-TYPE
|
||
SYNTAX AwcInvokeCommand
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Initiate saving of all specified
|
||
fileXferFile* files to the file server from
|
||
the system FLASH.
|
||
|
||
Commands recognized: start."
|
||
::= { awcFtp 7 }
|
||
|
||
awcFileXferCmdStatusFileSave OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Status of the most recent command to save
|
||
the specified fileXferFile* files.
|
||
Possible values:
|
||
0 = Operation completed successfully (or
|
||
has not taken place).
|
||
1 = Insufficient permission to save the
|
||
files.
|
||
2 = A directory specified for saving at
|
||
least one of the files was not found.
|
||
22 = No file specified, or invalid file
|
||
format.
|
||
68 = Operation is still in progress.
|
||
Poll again later.
|
||
72 = Operation was started, but later was
|
||
canceled."
|
||
::= { awcFtp 8 }
|
||
|
||
awcFileXferFileFirmwareSystem OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The filename of the system firmware image.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 9 }
|
||
|
||
awcFileXferFileFirmwareRadio0 OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The filename of the radio firmware image.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 10 }
|
||
|
||
awcFileXferFileWebUI OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The filename of the system Web pages image.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 11 }
|
||
|
||
awcFileXferFileFpgaPcmcia OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The filename of the FPGA image for the PCMCIA
|
||
controller. Max. string length is 128
|
||
octets."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 12 }
|
||
|
||
awcFileXferTftpPort OBJECT-TYPE
|
||
SYNTAX INTEGER (1..65535)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IP port number over which to perform TFTP
|
||
operations. Default 69."
|
||
DEFVAL { 69 }
|
||
::= { awcFtp 13 }
|
||
|
||
awcFileXferFtpDirectory OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Directory on defaultFileServer in which files
|
||
are located."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 14 }
|
||
|
||
-- awcFileXferFtpCtrlPort OBJECT-TYPE
|
||
-- SYNTAX INTEGER (1..65535)
|
||
-- MAX-ACCESS read-write
|
||
-- STATUS current
|
||
-- DESCRIPTION
|
||
-- "IP port number over which to perform FTP
|
||
-- Control operations."
|
||
-- ::= { awcFtp 15 }
|
||
|
||
-- awcFileXferFtpDataPort OBJECT-TYPE
|
||
-- SYNTAX INTEGER (1..65535)
|
||
-- MAX-ACCESS read-write
|
||
-- STATUS current
|
||
-- DESCRIPTION
|
||
-- "IP port number over which to perform FTP
|
||
-- Data operations."
|
||
-- ::= { awcFtp 16 }
|
||
|
||
awcFileXferFilesFLASH OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The filename of a complete FLASH firmware
|
||
image for the system, including all
|
||
non-configuration files within the system
|
||
FLASH file system. Max. string length is 128
|
||
octets."
|
||
DEFVAL { "AP340_latest.img" }
|
||
::= { awcFtp 17 }
|
||
|
||
awcFileXferFileFirmwareRadio1 OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The filename of the radio firmware image.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcFtp 18 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcFtp parameters
|
||
-- ********************************************************************
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcIfTable parameters
|
||
-- ********************************************************************
|
||
awcIfTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcIfEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IfTable attributes. In tabular form to
|
||
allow for multiple instances on an agent."
|
||
::= { awcVx 5 }
|
||
|
||
awcIfEntry OBJECT-TYPE
|
||
SYNTAX AwcIfEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcIfEntry table."
|
||
INDEX {ifIndex}
|
||
::= { awcIfTable 1 }
|
||
|
||
AwcIfEntry ::=
|
||
SEQUENCE {
|
||
awcIfDefaultPhysAddress MacAddress,
|
||
awcIfPhysAddress MacAddress,
|
||
awcIfAdoptPrimaryIdentity TruthValue,
|
||
awcIfDefaultIpAddress IpAddress,
|
||
awcIfDefaultIpNetMask IpAddress,
|
||
awcIfIpAddress IpAddress,
|
||
awcIfIpNetMask IpAddress,
|
||
awcIfMSDUMaxLength Unsigned32,
|
||
awcIfOutDiscardsCoS0 Counter32,
|
||
awcIfOutDiscardsCoS1 Counter32,
|
||
awcIfOutDiscardsCoS2 Counter32,
|
||
awcIfOutDiscardsCoS3 Counter32,
|
||
awcIfOutDiscardsCoS4 Counter32,
|
||
awcIfOutDiscardsCoS5 Counter32,
|
||
awcIfOutDiscardsCoS6 Counter32,
|
||
awcIfOutDiscardsCoS7 Counter32
|
||
}
|
||
|
||
awcIfDefaultPhysAddress OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default, factory-assigned MAC address of
|
||
the interface. Guaranteed to be unique across
|
||
all IEEE 802 devices."
|
||
::= { awcIfEntry 1 }
|
||
|
||
awcIfPhysAddress OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The MAC address to be used by the interface.
|
||
If awcIfDefaultPhysAddress is to be used, this
|
||
is 00:00:00:00:00:00."
|
||
DEFVAL { '000000000000'H }
|
||
::= { awcIfEntry 2 }
|
||
|
||
awcIfAdoptPrimaryIdentity OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, this interface adopts the identity of
|
||
bootconfigDev, the primary interface. This
|
||
includes MAC address, IP address, etc. This
|
||
is the conventional mode of operation when
|
||
operating as a transparent bridge. If false,
|
||
this interface always has a unique MAC
|
||
address."
|
||
DEFVAL { true }
|
||
::= { awcIfEntry 3 }
|
||
|
||
awcIfDefaultIpAddress OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default IPv4 Address of the interface.
|
||
If BOOTP or DHCP is enabled, this may be
|
||
overridden by the BOOTP or DHCP server."
|
||
DEFVAL { '0A000001'H }
|
||
::= { awcIfEntry 4 }
|
||
|
||
awcIfDefaultIpNetMask OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default IPv4 netmask of the interface.
|
||
If BOOTP or DHCP is enabled, this may
|
||
be overridden by the BOOTP or DHCP server."
|
||
DEFVAL { 'FFFFFF00'H }
|
||
::= { awcIfEntry 5 }
|
||
|
||
awcIfIpAddress OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IPv4 Address currently in use by the
|
||
interface."
|
||
::= { awcIfEntry 6 }
|
||
|
||
awcIfIpNetMask OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IPv4 netmask currently in use by the
|
||
interface."
|
||
::= { awcIfEntry 7 }
|
||
|
||
awcIfMSDUMaxLength OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Maximum length of the data portion of a packet
|
||
for this particular interface. This is the
|
||
maximum MAC Service Data Unit length, which is
|
||
greater than or equal to ifMtu, depending on
|
||
the configured MAC-level encapsulation."
|
||
::= { awcIfEntry 8 }
|
||
|
||
awcIfOutDiscardsCoS0 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 0 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 9 }
|
||
|
||
awcIfOutDiscardsCoS1 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 1 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 10 }
|
||
|
||
awcIfOutDiscardsCoS2 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 2 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 11 }
|
||
|
||
awcIfOutDiscardsCoS3 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 3 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 12 }
|
||
|
||
awcIfOutDiscardsCoS4 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 4 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 13 }
|
||
|
||
awcIfOutDiscardsCoS5 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 5 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 14 }
|
||
|
||
awcIfOutDiscardsCoS6 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 6 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 15 }
|
||
|
||
awcIfOutDiscardsCoS7 OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of outbound packets of CoS 7 which
|
||
were chosen to be discarded even though no
|
||
errors had been detected to prevent their
|
||
being transmitted. One possible reason for
|
||
discarding such a packet could be to free up
|
||
buffer space. Another reason would be
|
||
exceeding their maximum time-to-live."
|
||
::= { awcIfEntry 16 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcIfTable parameters
|
||
-- ********************************************************************
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awc802dot11 parameters
|
||
-- ********************************************************************
|
||
awcDot11smt OBJECT IDENTIFIER ::= {awc802dot11 1}
|
||
|
||
|
||
awcDot11StationConfigTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11StationConfigEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Station Config Table attributes. In tabular
|
||
form to allow for multiple instances on an
|
||
agent."
|
||
::= { awcDot11smt 1 }
|
||
|
||
awcDot11StationConfigEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11StationConfigEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11StationConfigTable
|
||
table."
|
||
INDEX {ifIndex}
|
||
::= { awcDot11StationConfigTable 1 }
|
||
|
||
AwcDot11StationConfigEntry ::=
|
||
SEQUENCE {
|
||
awcDot11StationRole INTEGER,
|
||
awcDot11PowerManagementSubMode Unsigned32,
|
||
awcDot11UseAWCExtensions TruthValue,
|
||
awcDot11AllowAssocBroadcastSSID TruthValue,
|
||
awcDot11PrivacyOptionImplementedMaxRate
|
||
Integer32,
|
||
awcDot11DesiredBSSLength INTEGER,
|
||
awcDot11EnetEncapsulationDefault INTEGER,
|
||
awcDot11ForceReqFirmwareVersion TruthValue,
|
||
awcDot11BridgeSpacing Unsigned32,
|
||
awcDot11DesiredSSIDMaxAssociatedSTA INTEGER,
|
||
awcDot11DesiredSSIDNumAssociatedSTA INTEGER,
|
||
awcDot11AuxiliarySSIDLength INTEGER,
|
||
awcDot11MultipleSSIDPerBSSImplemented
|
||
TruthValue,
|
||
awcDot11SymbolExtensionsImplemented
|
||
TruthValue,
|
||
awcDot11SymbolExtensionsEnabled TruthValue,
|
||
awcDot11DesiredSSIDMicAlgorithm
|
||
AwcDot11MicAlgorithm,
|
||
awcDot11DesiredSSIDWEPKeyPermuteAlgorithm
|
||
AwcDot11WEPKeyPermuteAlgorithm,
|
||
awcDot11DesiredSSIDInfrastructureWGB
|
||
TruthValue,
|
||
awcDot11DesiredSSIDDefaultPolId AwcPolId,
|
||
awcDot11DesiredSSIDDefaultVlanId AwcVlanId,
|
||
awcDot11DesiredSSIDEnableProxyMobileIP
|
||
TruthValue,
|
||
awcDot11InfrastructureSSID INTEGER,
|
||
awcDot11QBSSElementImplemented
|
||
TruthValue,
|
||
awcDot11QBSSElementEnabled TruthValue,
|
||
awcDot11InfrastructureSSIDExclusive
|
||
TruthValue,
|
||
awcDot11SendIGMPGeneralQuery TruthValue,
|
||
awcDot11NonRootMobility INTEGER
|
||
}
|
||
|
||
awcDot11StationRole OBJECT-TYPE
|
||
SYNTAX INTEGER {roleClient(1), roleIBSS(2),
|
||
roleRepeater(3), roleAP(4)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The role of this station itself within the
|
||
802.11 BSS (radio cell) of which it is a
|
||
member."
|
||
DEFVAL { roleAP }
|
||
::= { awcDot11StationConfigEntry 1 }
|
||
|
||
awcDot11PowerManagementSubMode OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"When configured as roleClient, the Power
|
||
Management Submode of the device."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11StationConfigEntry 2 }
|
||
|
||
awcDot11UseAWCExtensions OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, Aironet extensions to the basic
|
||
802.11 protocol are enabled. This results in
|
||
better BSS performance and faster roaming.
|
||
If false, only the basic 802.11 protocols
|
||
are used. This ensures maximum compatibility
|
||
with non-Aironet equipment."
|
||
DEFVAL { true }
|
||
::= { awcDot11StationConfigEntry 3 }
|
||
|
||
awcDot11AllowAssocBroadcastSSID OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true and awcDot11StationRole is either
|
||
roleAP or roleRepeater, the radio will respond
|
||
to Broadcast SSID Probe Requests and will
|
||
broadcast its own SSID within its Beacons. If
|
||
false, the radio will not respond to the
|
||
Broadcast SSID and will not broadcast its SSID
|
||
within Beacons."
|
||
DEFVAL { true }
|
||
::= { awcDot11StationConfigEntry 4 }
|
||
|
||
awcDot11PrivacyOptionImplementedMaxRate OBJECT-TYPE
|
||
SYNTAX Integer32 (2..127)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum Transmit bit rate supported by the
|
||
radio when using WEP encryption. Expressed in
|
||
standard 802.11 increments of 500Kb/sec."
|
||
::= { awcDot11StationConfigEntry 5 }
|
||
|
||
awcDot11DesiredBSSLength OBJECT-TYPE
|
||
SYNTAX INTEGER (0..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of entries in
|
||
awcDot11DesiredBSSTable."
|
||
::= { awcDot11StationConfigEntry 6 }
|
||
|
||
awcDot11EnetEncapsulationDefault OBJECT-TYPE
|
||
SYNTAX INTEGER {encap802dot1H(1), encapRfc1042(2)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Ethernet Encapsulation Transform type used
|
||
within the BSS. Either IEEE 802.1H or
|
||
RFC 1042 can be utilized. IEEE 802.1H
|
||
provides exceptions for the Novel
|
||
IPX and AARP protocols."
|
||
DEFVAL { encapRfc1042 }
|
||
::= { awcDot11StationConfigEntry 7 }
|
||
|
||
awcDot11ForceReqFirmwareVersion OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the radio driver will only allow
|
||
operation with the specific radio firmware
|
||
revision with which it was originally tested.
|
||
If false, the radio driver will allow
|
||
operation with the radio firmware revision
|
||
with which it was tested, or any later radio
|
||
firmware revision."
|
||
DEFVAL { true }
|
||
::= { awcDot11StationConfigEntry 8 }
|
||
|
||
awcDot11BridgeSpacing OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If this device is the root side of a Bridge
|
||
configuration, this value is the distance in
|
||
kilometers reported between this device and
|
||
its farthest non-root Bridge."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11StationConfigEntry 9 }
|
||
|
||
awcDot11DesiredSSIDMaxAssociatedSTA OBJECT-TYPE
|
||
SYNTAX INTEGER (0..2007)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum number of 802.11 Stations which
|
||
may Associate with this access point through
|
||
either the Broadcast SSID or through
|
||
dot11DesiredSSID. If 0, the maximum number
|
||
is limited only by the 802.11 standard and
|
||
by any hardware or radio firmware limitations
|
||
of the access point."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11StationConfigEntry 10 }
|
||
|
||
awcDot11DesiredSSIDNumAssociatedSTA OBJECT-TYPE
|
||
SYNTAX INTEGER (0..2007)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current number of 802.11 Stations which
|
||
are Associated with this access point through
|
||
either the Broadcast SSID or through
|
||
dot11DesiredSSID."
|
||
::= { awcDot11StationConfigEntry 11 }
|
||
|
||
awcDot11AuxiliarySSIDLength OBJECT-TYPE
|
||
SYNTAX INTEGER (0..2007)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum number of entries in
|
||
awcDot11AuxiliarySSIDTable. If
|
||
awcDot11MultipleSSIDPerBSSImplemented is FALSE,
|
||
awcDot11AuxiliarySSIDLength must be 0."
|
||
::= { awcDot11StationConfigEntry 12 }
|
||
|
||
awcDot11MultipleSSIDPerBSSImplemented OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This attribute, when TRUE, indicates that the station
|
||
implementation is capable of responding to 802.11
|
||
Probe Requests for SSIDs other than dot11DesiredSSID.
|
||
The default value of this attribute is FALSE."
|
||
::= { awcDot11StationConfigEntry 13 }
|
||
|
||
awcDot11SymbolExtensionsImplemented OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This attribute, when TRUE, indicates that the station
|
||
implementation is capable of generating Symbol, Inc.
|
||
proprietary elements in its Beacons and Probe
|
||
Responses. These elements enable support for Symbol
|
||
Voice-over-IP (VoIP) phones. The default value of
|
||
this attribute is FALSE."
|
||
::= { awcDot11StationConfigEntry 14 }
|
||
|
||
awcDot11SymbolExtensionsEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should the Radio generate Symbol, Inc. proprietary
|
||
elements in its Beacons and Probe Responses in support
|
||
of Symbol VoIP phones?"
|
||
DEFVAL { false }
|
||
::= { awcDot11StationConfigEntry 15 }
|
||
|
||
awcDot11DesiredSSIDMicAlgorithm OBJECT-TYPE
|
||
SYNTAX AwcDot11MicAlgorithm
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Auxiliary Message Integrity Check (MIC) calculated on
|
||
WEP-encoded packets of stations Associated to this
|
||
access point through either the Broadcast SSID or
|
||
dot11DesiredSSID."
|
||
DEFVAL { micNone }
|
||
::= { awcDot11StationConfigEntry 16 }
|
||
|
||
awcDot11DesiredSSIDWEPKeyPermuteAlgorithm OBJECT-TYPE
|
||
SYNTAX AwcDot11WEPKeyPermuteAlgorithm
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Function through which the WEP encryption key is
|
||
permuted between key renewal periods for stations
|
||
Associated to this access point through either the
|
||
Broadcast SSID or dot11DesiredSSID."
|
||
DEFVAL { wepPermuteNone }
|
||
::= { awcDot11StationConfigEntry 17 }
|
||
|
||
awcDot11DesiredSSIDInfrastructureWGB OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"When true, Workgroup Bridge-class devices Associated to
|
||
this access point through either the
|
||
Broadcast SSID or dot11DesiredSSID are provided
|
||
the class of service which is provided to network
|
||
infrastructure stations by their parent access point.
|
||
This includes use of the 802.11 reliable multicast
|
||
protocol (4-address packets for multicast). When false,
|
||
Workgroup Bridge-class devices are provided the class of
|
||
service which is provided to ordinary client stations."
|
||
DEFVAL { true }
|
||
::= { awcDot11StationConfigEntry 18 }
|
||
|
||
awcDot11DesiredSSIDDefaultPolId OBJECT-TYPE
|
||
SYNTAX AwcPolId
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default Policy Group Identifier for stations
|
||
Associated to this access point through either the
|
||
Broadcast SSID or dot11DesiredSSID. A value of 0
|
||
indicates that no special policies are to be applied
|
||
by default."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11StationConfigEntry 19 }
|
||
|
||
awcDot11DesiredSSIDDefaultVlanId OBJECT-TYPE
|
||
SYNTAX AwcVlanId
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default VLAN Identifier for stations
|
||
Associated to this access point through either the
|
||
Broadcast SSID or dot11DesiredSSID. A value of 0
|
||
indicates that either VLANs are disabled or that
|
||
the default VLAN is awcNativeVlanId."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11StationConfigEntry 20 }
|
||
|
||
awcDot11DesiredSSIDEnableProxyMobileIP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, Proxy Mobile IP is enabled for use by
|
||
all stations Associated to this access point
|
||
through either the Broadcast SSID or
|
||
dot11DesiredSSID."
|
||
DEFVAL { false }
|
||
::= { awcDot11StationConfigEntry 21 }
|
||
|
||
awcDot11InfrastructureSSID OBJECT-TYPE
|
||
SYNTAX INTEGER (0..2007)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Index of the SSID which all 802.11 infrastructure
|
||
stations shall use for Association. If 0, an
|
||
access point and its repeaters and other
|
||
subordinate infrastructure devices will Associate
|
||
through dot11DesiredSSID. If non-0, an access
|
||
point and its subordinate infrastructure devices
|
||
will Associate through the auxiliary SSID with
|
||
awcDot11AuxSSIDIndex equal to
|
||
awcDot11InfrastructureSSID."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11StationConfigEntry 22 }
|
||
|
||
awcDot11QBSSElementImplemented OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This attribute, when TRUE, indicates that the station
|
||
implementation is capable of generating 802.11e QBSS
|
||
elements in its Beacons and Probe
|
||
Responses. These elements enable support for basic
|
||
802.11 Quality of Service. The default value of
|
||
this attribute is FALSE."
|
||
::= { awcDot11StationConfigEntry 23 }
|
||
|
||
awcDot11QBSSElementEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should the Radio generate 802.11e QBSS
|
||
elements in its Beacons and Probe Responses in support
|
||
of 802.11 Quality of Service?"
|
||
DEFVAL { false }
|
||
::= { awcDot11StationConfigEntry 24 }
|
||
|
||
awcDot11InfrastructureSSIDExclusive OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should this access point restrict all infrastructure
|
||
stations to associate only through the SSID specified
|
||
by awcDot11InfrastructureSSID?"
|
||
DEFVAL { false }
|
||
::= { awcDot11StationConfigEntry 25 }
|
||
|
||
awcDot11SendIGMPGeneralQuery OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should this access point issue an IGMP General Query
|
||
to all associated stations when they complete all
|
||
required high-level authentication? Such an IGMP
|
||
query can help configure multicast groups efficiently."
|
||
DEFVAL { false }
|
||
::= { awcDot11StationConfigEntry 26 }
|
||
|
||
awcDot11NonRootMobility OBJECT-TYPE
|
||
SYNTAX INTEGER {
|
||
mobile(1),
|
||
stationary(2)
|
||
}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This object is used to determine if the radio
|
||
should look for a better parent AP in heavy
|
||
traffic condition when the awcDot11StationRole
|
||
is roleClient(1) or roleRepeater(3). It will
|
||
look for better parent if it is mobile(1)
|
||
and will not look for better parent if it is
|
||
stationary(2)."
|
||
DEFVAL { stationary }
|
||
::= { awcDot11StationConfigEntry 27 }
|
||
|
||
|
||
awcDot11AuthenticationAlgorithmsTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11AuthenticationAlgorithmsEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This table contains attributes to configure
|
||
authentication algorithm parameters for associations
|
||
through the SSID defined by IEEE802dot11-MIB
|
||
dot11DesiredSSID object. It defines attributes
|
||
additional to those defined in the IEEE802dot11-MIB
|
||
dot11AuthenticationAlgorithmsTable. An interface
|
||
may support multiple authentication algorithms.
|
||
|
||
This table has an expansion dependent relationship
|
||
on the ifTable. For each entry in this table,
|
||
there exists at least an entry in the ifTable of
|
||
ifType ieee80211(71). This table uses the
|
||
dot11AuthenticationAlgorithmsIndex of the
|
||
dot11AuthenticationAlgorithmsTable defined in the
|
||
IEEE802dot11-MIB as the expansion index.
|
||
|
||
Entries in this table cannot be created or deleted
|
||
by the network management system. All entries are
|
||
created or deleted by the agent."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 5.7.6 and IEEE802dot11-MIB."
|
||
::= { awcDot11smt 2 }
|
||
|
||
awcDot11AuthenticationAlgorithmsEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11AuthenticationAlgorithmsEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Each entry specifies Cisco Aironet product
|
||
specific authentication algorithm
|
||
configuration attributes of the dot11DesiredSSID
|
||
on a radio interface."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 8.2 and IEEE802dot11-MIB."
|
||
INDEX { ifIndex,
|
||
awcDot11AuthenticationAlgorithmsIndex}
|
||
::= { awcDot11AuthenticationAlgorithmsTable 1 }
|
||
|
||
AwcDot11AuthenticationAlgorithmsEntry ::= SEQUENCE {
|
||
awcDot11AuthenticationAlgorithmsIndex Integer32,
|
||
awcDot11AuthenticationRequireEAP TruthValue,
|
||
awcDot11AuthenticationDefaultUcastAllowedToGoTo
|
||
OCTET STRING }
|
||
|
||
|
||
awcDot11AuthenticationAlgorithmsIndex OBJECT-TYPE
|
||
SYNTAX Integer32 (1..65536)
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The auxiliary variable used to identify instances
|
||
of the columnar objects in the Aironet Authentication
|
||
Algorithms Table. This variable corresponds directly
|
||
to the 802.11 dot11AuthenticationAlgorithmsIndex."
|
||
::= { awcDot11AuthenticationAlgorithmsEntry 1 }
|
||
|
||
awcDot11AuthenticationRequireEAP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, stations authenticating with the
|
||
corresponding dot11AuthenticationAlgorithm
|
||
must complete network-level EAP authentication
|
||
before they will be unblocked. If false,
|
||
stations authenticating with the corresponding
|
||
dot11AuthenticationAlgorithm will be unblocked
|
||
as soon as they complete the requirements of
|
||
802.11 authentication."
|
||
::= { awcDot11AuthenticationAlgorithmsEntry 2 }
|
||
|
||
awcDot11AuthenticationDefaultUcastAllowedToGoTo OBJECT-TYPE
|
||
SYNTAX OCTET STRING
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The set of ports to which frames received from
|
||
a specific port and destined for a MAC address
|
||
which is not already listed in dot1dStaticTable
|
||
and authenticates with the corresponding
|
||
dot11AuthenticationAlgorithm, are allowed to be
|
||
forwarded. Each octet within the value of this
|
||
object specifies a set of eight ports, with the
|
||
first octet specifying ports 1 through 8, the
|
||
second octet specifying ports 9 through 16, etc.
|
||
Within each octet, the most significant bit
|
||
represents the lowest numbered port, and the
|
||
least significant bit represents the highest
|
||
numbered port. Thus, each port of the bridge is
|
||
represented by a single bit within the value of
|
||
this object. If that bit has a value of
|
||
'1' then that port is included in the set of
|
||
ports; the port is not included if its bit has a
|
||
value of '0'. (Note that the setting of the bit
|
||
corresponding to the port from which a frame is
|
||
received is irrelevant.) The default value of
|
||
this object is a string of ones of appropriate
|
||
length."
|
||
REFERENCE
|
||
"RFC 1493, BRIDGE-MIB, dot1dStaticTable."
|
||
::= { awcDot11AuthenticationAlgorithmsEntry 3 }
|
||
|
||
|
||
awcDot11WEPDefaultKeysTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11WEPDefaultKeysEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Extension of dot11WEPDefaultKeysTable to allow
|
||
for key lengths other than 40 bits."
|
||
::= { awcDot11smt 3 }
|
||
|
||
awcDot11WEPDefaultKeysEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11WEPDefaultKeysEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11WEPDefaultKeysTable
|
||
table."
|
||
INDEX {ifIndex, awcDot11WEPDefaultKeyIndex}
|
||
::= { awcDot11WEPDefaultKeysTable 1 }
|
||
|
||
AwcDot11WEPDefaultKeysEntry ::=
|
||
SEQUENCE {
|
||
awcDot11WEPDefaultKeyIndex INTEGER,
|
||
awcDot11WEPDefaultKeyLen INTEGER,
|
||
awcDot11WEPDefaultKeyValue WEPKeytype128
|
||
}
|
||
|
||
awcDot11WEPDefaultKeyIndex OBJECT-TYPE
|
||
SYNTAX INTEGER (1..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The auxiliary variable used to identify
|
||
instances of the columnar objects in the WEP
|
||
Default Keys Table. The value of this
|
||
variable is equal to the WEPDefaultKeyID + 1"
|
||
::= { awcDot11WEPDefaultKeysEntry 1 }
|
||
|
||
awcDot11WEPDefaultKeyLen OBJECT-TYPE
|
||
SYNTAX INTEGER (0..13)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Length in octets of
|
||
awcDot11WEPDefaultKeyValue. If 0, the
|
||
corresponding awcDot11WEPDefaultKeyValue is
|
||
not configured."
|
||
::= { awcDot11WEPDefaultKeysEntry 2 }
|
||
|
||
awcDot11WEPDefaultKeyValue OBJECT-TYPE
|
||
SYNTAX WEPKeytype128
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A WEP default secret key value. The value is
|
||
write-only (attempt to read will result in
|
||
return of a zero-length string)."
|
||
::= { awcDot11WEPDefaultKeysEntry 3 }
|
||
|
||
|
||
awcDot11PrivacyTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11PrivacyEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Additional information about the WEP
|
||
capabilities of the device. In tabular form
|
||
to allow for multiple instances on an agent."
|
||
::= { awcDot11smt 5 }
|
||
|
||
awcDot11PrivacyEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11PrivacyEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11PrivacyTable table."
|
||
INDEX {ifIndex}
|
||
::= { awcDot11PrivacyTable 1 }
|
||
|
||
AwcDot11PrivacyEntry ::=
|
||
SEQUENCE {
|
||
awcDot11WEPDefaultKeyMaxIndex INTEGER,
|
||
awcDot11AllowEncrypted TruthValue,
|
||
awcDot11WEPKeyMaxLen INTEGER,
|
||
awcDot11LEAPUserName OCTET STRING,
|
||
awcDot11LEAPPassword OCTET STRING
|
||
}
|
||
|
||
awcDot11WEPDefaultKeyMaxIndex OBJECT-TYPE
|
||
SYNTAX INTEGER (0..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum WEP Default Key index which the
|
||
radio supports. Range 1..4, or 0 if the radio
|
||
does not support WEP."
|
||
::= { awcDot11PrivacyEntry 1 }
|
||
|
||
awcDot11AllowEncrypted OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"When this attribute is true, the STA shall
|
||
indicate at the MAC service interface received
|
||
MSDUs regardless of the setting of the WEP
|
||
subfield of the Frame Control field, so long
|
||
as the dot11ExcludeUnencrypted attribute is
|
||
false. The default value of this attribute
|
||
shall be false."
|
||
DEFVAL { false }
|
||
::= { awcDot11PrivacyEntry 2 }
|
||
|
||
awcDot11WEPKeyMaxLen OBJECT-TYPE
|
||
SYNTAX INTEGER (0..16)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum WEP Key Length which the radio
|
||
supports. Range 0..16, or 0 if the radio does
|
||
not support WEP. Note that, even if the radio
|
||
supports more than 13 octets of key value, the
|
||
current 802.11 standard only makes use of
|
||
the first 13 octets."
|
||
::= { awcDot11PrivacyEntry 3 }
|
||
|
||
awcDot11LEAPUserName OBJECT-TYPE
|
||
SYNTAX OCTET STRING
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"User Name assigned to the system for use when
|
||
authenticating with AAA servers."
|
||
DEFVAL { "" }
|
||
::= { awcDot11PrivacyEntry 4}
|
||
|
||
awcDot11LEAPPassword OBJECT-TYPE
|
||
SYNTAX OCTET STRING (SIZE (0..256))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"User Password (shared secret) assigned to the system
|
||
for use when authenticating with AAA servers."
|
||
DEFVAL { "" }
|
||
::= { awcDot11PrivacyEntry 5}
|
||
|
||
awcDot11DesiredBSSTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11DesiredBSSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"When the radio is not in roleAP, a list of
|
||
preferred Access Points with which the radio
|
||
should Associate. In tabular form to allow for
|
||
multiple instances on an agent."
|
||
::= { awcDot11smt 6 }
|
||
|
||
awcDot11DesiredBSSEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11DesiredBSSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11DesiredBSSTable
|
||
table."
|
||
INDEX {ifIndex, awcDot11DesiredBSSIndex}
|
||
::= { awcDot11DesiredBSSTable 1 }
|
||
|
||
AwcDot11DesiredBSSEntry ::=
|
||
SEQUENCE {
|
||
awcDot11DesiredBSSIndex INTEGER,
|
||
awcDot11DesiredBSS MacAddress
|
||
}
|
||
|
||
awcDot11DesiredBSSIndex OBJECT-TYPE
|
||
SYNTAX INTEGER (1..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The priority order in which Preferred Access
|
||
Points should be probed. Lower indices are
|
||
probed first."
|
||
::= { awcDot11DesiredBSSEntry 1 }
|
||
|
||
awcDot11DesiredBSS OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The BSS identifier (MAC address) of the Access
|
||
Point with which the radio should try to
|
||
Associate, or 00:00:00:00:00:00 if the BSS
|
||
identifier for this priority is unspecified."
|
||
DEFVAL { '000000000000'H }
|
||
::= { awcDot11DesiredBSSEntry 2 }
|
||
|
||
|
||
awcDot11AuxiliarySSIDTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11AuxiliarySSIDEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"When the radio is not in roleClient, a list of
|
||
Stations which, when Associated to this system,
|
||
shall always have the same AID."
|
||
::= { awcDot11smt 7 }
|
||
|
||
awcDot11AuxiliarySSIDEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11AuxiliarySSIDEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11AuxiliarySSIDTable
|
||
table."
|
||
INDEX {ifIndex, awcDot11AuxSSIDIndex}
|
||
::= { awcDot11AuxiliarySSIDTable 1 }
|
||
|
||
AwcDot11AuxiliarySSIDEntry ::=
|
||
SEQUENCE {
|
||
awcDot11AuxSSIDIndex INTEGER,
|
||
awcDot11AuxSSID OCTET STRING,
|
||
awcDot11AuxSSIDMaxAssociatedSTA INTEGER,
|
||
awcDot11AuxSSIDNumAssociatedSTA INTEGER,
|
||
awcDot11AuxSSIDDefaultPolId AwcPolId,
|
||
awcDot11AuxSSIDDefaultVlanId AwcVlanId,
|
||
awcDot11AuxSSIDEnableProxyMobileIP
|
||
TruthValue
|
||
}
|
||
|
||
awcDot11AuxSSIDIndex OBJECT-TYPE
|
||
SYNTAX INTEGER (1..2007)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Identifier of auxiliary SSIDs supported by the access
|
||
point in addition to dot11DesiredSSID. Domain from 1
|
||
to awcDot11AuxiliarySSIDLength."
|
||
::= { awcDot11AuxiliarySSIDEntry 1 }
|
||
|
||
awcDot11AuxSSID OBJECT-TYPE
|
||
SYNTAX OCTET STRING (SIZE(0..32))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This attribute reflects a Service Set ID recognized
|
||
by the access point. The access point shall respond
|
||
to Probe Requests specifying this SSID, but does not
|
||
advertise this SSID in its Beacons."
|
||
DEFVAL { "" }
|
||
::= { awcDot11AuxiliarySSIDEntry 2 }
|
||
|
||
awcDot11AuxSSIDMaxAssociatedSTA OBJECT-TYPE
|
||
SYNTAX INTEGER (0..2007)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum number of 802.11 Stations which
|
||
may Associate with this access point through
|
||
awcDot11AuxSSID. If 0, the maximum number
|
||
is limited only by the 802.11 standard and
|
||
by any hardware or radio firmware limitations
|
||
of the access point."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11AuxiliarySSIDEntry 3 }
|
||
|
||
awcDot11AuxSSIDNumAssociatedSTA OBJECT-TYPE
|
||
SYNTAX INTEGER (0..2007)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current number of 802.11 Stations which
|
||
are Associated with this access point through
|
||
awcDot11AuxSSID."
|
||
::= { awcDot11AuxiliarySSIDEntry 4 }
|
||
|
||
awcDot11AuxSSIDDefaultPolId OBJECT-TYPE
|
||
SYNTAX AwcPolId
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default Policy Group Identifier for stations
|
||
Associated to this access point over awcDot11AuxSSID.
|
||
A value of 0 indicates that no special policies are
|
||
to be applied by default."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11AuxiliarySSIDEntry 6 }
|
||
|
||
awcDot11AuxSSIDDefaultVlanId OBJECT-TYPE
|
||
SYNTAX AwcVlanId
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default VLAN Identifier for stations
|
||
Associated to this access point over awcDot11AuxSSID.
|
||
A value of 0 indicates that either VLANs are disabled
|
||
or that the default VLAN is awcNativeVlanId."
|
||
DEFVAL { 0 }
|
||
::= { awcDot11AuxiliarySSIDEntry 7 }
|
||
|
||
awcDot11AuxSSIDEnableProxyMobileIP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, Proxy Mobile IP is enabled for use by
|
||
all stations Associated to this access point
|
||
over awcDot11AuxSSID."
|
||
DEFVAL { false }
|
||
::= { awcDot11AuxiliarySSIDEntry 8 }
|
||
|
||
awcDot11AuxSSIDAuthAlgTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11AuxSSIDAuthAlgEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This (conceptual) table of attributes shall be a set of
|
||
all the Aironet-specific parameters for each authentication
|
||
algorithm supported by the station for each auxiliary SSID
|
||
listed in awcDot11AuxiliarySSIDTable."
|
||
::= { awcDot11smt 8 }
|
||
|
||
awcDot11AuxSSIDAuthAlgEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11AuxSSIDAuthAlgEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An Entry (conceptual row) in the Aironet Auxiliary SSID
|
||
Authentication Algorithms Table.
|
||
|
||
ifIndex - Each 802.11 interface is represented by an
|
||
ifEntry. Interface tables in this MIB module are indexed
|
||
by ifIndex."
|
||
|
||
INDEX { ifIndex,
|
||
awcDot11AuxSSIDIndex,
|
||
awcDot11AuxSSIDAuthAlgIndex}
|
||
::= { awcDot11AuxSSIDAuthAlgTable 1 }
|
||
|
||
AwcDot11AuxSSIDAuthAlgEntry ::= SEQUENCE {
|
||
awcDot11AuxSSIDAuthAlgIndex Integer32,
|
||
awcDot11AuxSSIDAuthAlgEnable TruthValue,
|
||
awcDot11AuxSSIDAuthAlgRequireEAP TruthValue,
|
||
awcDot11AuxSSIDAuthAlgDefaultUcastAllowedToGoTo
|
||
OCTET STRING
|
||
}
|
||
|
||
|
||
awcDot11AuxSSIDAuthAlgIndex OBJECT-TYPE
|
||
SYNTAX Integer32 (1..65536)
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The auxiliary variable used to identify instances
|
||
of the columnar objects in the Aironet Auxiliary SSID
|
||
Authentication Algorithms Table. This variable
|
||
corresponds directly to the 802.11
|
||
dot11AuthenticationAlgorithmsIndex."
|
||
::= { awcDot11AuxSSIDAuthAlgEntry 1 }
|
||
|
||
awcDot11AuxSSIDAuthAlgEnable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, stations may authenticate to the SSID
|
||
specified by awcDot11AuxSSIDIndex with the algorithm
|
||
corresponding to dot11AuthenticationAlgorithmsIndex."
|
||
::= { awcDot11AuxSSIDAuthAlgEntry 2 }
|
||
|
||
awcDot11AuxSSIDAuthAlgRequireEAP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, stations authenticating to the SSID
|
||
specified by awcDot11AuxSSIDIndex with the
|
||
corresponding dot11AuthenticationAlgorithm
|
||
must complete network-level EAP authentication
|
||
before they will be unblocked. If false,
|
||
stations authenticating with the corresponding
|
||
dot11AuthenticationAlgorithm will be unblocked
|
||
as soon as they complete the requirements of
|
||
802.11 authentication."
|
||
::= { awcDot11AuxSSIDAuthAlgEntry 3 }
|
||
|
||
awcDot11AuxSSIDAuthAlgDefaultUcastAllowedToGoTo OBJECT-TYPE
|
||
SYNTAX OCTET STRING
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The set of ports to which frames received from a
|
||
specific port and destined for a MAC address which
|
||
is not already listed in dot1dStaticTable and
|
||
authenticates to the SSID specified by
|
||
awcDot11AuxSSIDIndex with the corresponding
|
||
dot11AuthenticationAlgorithm, are
|
||
allowed to be forwarded. Each octet
|
||
within the value of this object specifies a set of
|
||
eight ports, with the first octet specifying ports
|
||
1 through 8, the second octet specifying ports 9
|
||
through 16, etc. Within each octet, the most
|
||
significant bit represents the lowest numbered
|
||
port, and the least significant bit represents the
|
||
highest numbered port. Thus, each port of the
|
||
bridge is represented by a single bit within the
|
||
value of this object. If that bit has a value of
|
||
'1' then that port is included in the set of
|
||
ports; the port is not included if its bit has a
|
||
value of '0'. (Note that the setting of the bit
|
||
corresponding to the port from which a frame is
|
||
received is irrelevant.) The default value of
|
||
this object is a string of ones of appropriate
|
||
length."
|
||
::= { awcDot11AuxSSIDAuthAlgEntry 4 }
|
||
|
||
|
||
awcDot11AssignedAIDTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11AssignedAIDEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"When the radio is not functioning as a client
|
||
station (i.e., awcDot11StationRole is not
|
||
'roleClient'), this is the list of AIDs which
|
||
this agent will assign to the clients
|
||
associating with it. An AID is assigned if
|
||
the corresponding MAC address matches that of
|
||
the client. This table has an expansion
|
||
dependent relationship on the ifTable. For
|
||
each entry in this table, there exists at least
|
||
an entry in the ifTable of ifType ieee80211(71)."
|
||
::= { awcDot11smt 9 }
|
||
|
||
awcDot11AssignedAIDEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11AssignedAIDEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11AssignedAIDTable
|
||
table."
|
||
INDEX {ifIndex, awcDot11AssignedAID}
|
||
::= { awcDot11AssignedAIDTable 1 }
|
||
|
||
AwcDot11AssignedAIDEntry ::=
|
||
SEQUENCE {
|
||
awcDot11AssignedAID INTEGER,
|
||
awcDot11AssignedSTA MacAddress
|
||
}
|
||
|
||
awcDot11AssignedAID OBJECT-TYPE
|
||
SYNTAX INTEGER (2..2007)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An AID which shall be reserved for the
|
||
exclusive use of a single Station."
|
||
::= { awcDot11AssignedAIDEntry 1 }
|
||
|
||
awcDot11AssignedSTA OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Station (MAC address) which, when
|
||
Associated to this system, shall always
|
||
be assigned awcDot11AssignedAID as its
|
||
802.11 AID."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 5.7.2."
|
||
DEFVAL { '000000000000'H }
|
||
::= { awcDot11AssignedAIDEntry 2 }
|
||
|
||
|
||
awcDot11AccessPointCountersTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11AccessPointCountersEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This table includes radio statistics collected
|
||
by the IEEE 802.11 radio interface. This
|
||
table has a sparse dependent relationship on
|
||
the ifTable. For each entry in this table,
|
||
there exists an entry in the ifTable of
|
||
ifType ieee80211(71)."
|
||
::= { awcDot11smt 10 }
|
||
|
||
awcDot11AccessPointCountersEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11AccessPointCountersEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Each entry contains counters of frame
|
||
transmissions and client associations for a
|
||
radio interface."
|
||
INDEX {ifIndex}
|
||
::= { awcDot11AccessPointCountersTable 1 }
|
||
|
||
AwcDot11AccessPointCountersEntry ::=
|
||
SEQUENCE {
|
||
awcDot11AssociatedStationCount Counter32,
|
||
awcDot11AuthenticatedStationCount Counter32,
|
||
awcDot11ReassociatedStationCount Counter32,
|
||
awcDot11RoamedStationCount Counter32,
|
||
awcDot11DeauthenticateCount Counter32,
|
||
awcDot11DisassociateCount Counter32,
|
||
awcDot11EncapPktsMMH Counter32,
|
||
awcDot11DecapPktsMMH Counter32,
|
||
awcDot11EncapErrorsMMH Counter32,
|
||
awcDot11DecapErrorsMMH Counter32,
|
||
awcDot11DecapExistsMMH Counter32,
|
||
awcDot11DecapAccessMMH Counter32
|
||
}
|
||
|
||
awcDot11AssociatedStationCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of successful 802.11 Association Request
|
||
operations to this radio of this access point since system
|
||
startup."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 5.7."
|
||
::= { awcDot11AccessPointCountersEntry 1}
|
||
|
||
awcDot11AuthenticatedStationCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of successful 802.11 MAC-level
|
||
Authentication operations to this radio of this access
|
||
point since system startup. "
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 5.7."
|
||
::= { awcDot11AccessPointCountersEntry 2 }
|
||
|
||
awcDot11ReassociatedStationCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of successful 802.11 Reassociation Request
|
||
operations to this radio of this access point since system
|
||
startup."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 5.7."
|
||
::= { awcDot11AccessPointCountersEntry 3 }
|
||
|
||
awcDot11RoamedStationCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of times that clients which had
|
||
successfully (re)associated with this access point
|
||
successfully reassociated with another access point
|
||
since system startup."
|
||
::= { awcDot11AccessPointCountersEntry 4 }
|
||
|
||
awcDot11DeauthenticateCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of Deauthenticate frames sent over this
|
||
radio of this access point since system startup."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 5.7."
|
||
::= { awcDot11AccessPointCountersEntry 5 }
|
||
|
||
awcDot11DisassociateCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of Disassociate frames sent over this
|
||
radio of this access point since system startup."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 5.7."
|
||
::= { awcDot11AccessPointCountersEntry 6 }
|
||
|
||
awcDot11EncapPktsMMH OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of packets for which the a MIC has been
|
||
requested to be calculated with the MMH algorithm
|
||
before being submitted for transmission over
|
||
this radio of this access point since system startup."
|
||
::= { awcDot11AccessPointCountersEntry 7 }
|
||
|
||
awcDot11DecapPktsMMH OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of packets received over this radio of
|
||
this access point since system startup and for which
|
||
a MIC has been requested to be validated with the
|
||
MMH algorithm."
|
||
::= { awcDot11AccessPointCountersEntry 8 }
|
||
|
||
awcDot11EncapErrorsMMH OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of packets which have failed MIC
|
||
calculation with the MMH algorithm before being
|
||
submitted for transmission over this
|
||
radio of this access point since system startup."
|
||
::= { awcDot11AccessPointCountersEntry 9 }
|
||
|
||
awcDot11DecapErrorsMMH OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of packets received over this radio of
|
||
this access point since system startup which have
|
||
failed MIC validation with the MMH algorithm."
|
||
::= { awcDot11AccessPointCountersEntry 10 }
|
||
|
||
awcDot11DecapExistsMMH OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of packets received over this radio of
|
||
this access point since system startup which have
|
||
failed MIC validation with the MMH algorithm
|
||
specifically due to sequence number and duplicate
|
||
packet errors."
|
||
::= { awcDot11AccessPointCountersEntry 11 }
|
||
|
||
awcDot11DecapAccessMMH OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of packets received over this radio of
|
||
this access point since system startup which have
|
||
failed MIC validation with the MMH algorithm
|
||
specifically due to cryptographic key-mismatch
|
||
errors."
|
||
::= { awcDot11AccessPointCountersEntry 12 }
|
||
|
||
|
||
awcDot11mac OBJECT IDENTIFIER ::= {awc802dot11 2}
|
||
|
||
awcDot11CountersTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11CountersEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This table contains MAC statistics
|
||
on each of IEEE 802.11 interface.
|
||
This table has a sparse dependent
|
||
relationship on the ifTable. For
|
||
each entry in this table, there exists
|
||
an entry in the ifTable of ifType
|
||
ieee80211(71)."
|
||
::= { awcDot11mac 2 }
|
||
|
||
awcDot11CountersEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11CountersEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Each entry contains counters of frame
|
||
transmissions for a radio interface."
|
||
INDEX { ifIndex }
|
||
::= { awcDot11CountersTable 1 }
|
||
|
||
AwcDot11CountersEntry ::=
|
||
SEQUENCE {
|
||
awcDot11TxDeferEnergyCount Counter32,
|
||
awcDot11RxMacCrcErrorCount Counter32,
|
||
awcDot11SsidMismatchCount Counter32}
|
||
|
||
|
||
awcDot11TxDeferEnergyCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of frames deferred transmission
|
||
due to energy detect since system startup."
|
||
::= { awcDot11CountersEntry 1 }
|
||
|
||
awcDot11RxMacCrcErrorCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of frames received with
|
||
MAC CRC errors since system startup."
|
||
::= { awcDot11CountersEntry 2 }
|
||
|
||
awcDot11SsidMismatchCount OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Total number of Beacon or Probe Response frames received
|
||
for which the SSID does not match dot11DesiredSSID
|
||
since system startup."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, IEEE802dot11-MIB."
|
||
::= { awcDot11CountersEntry 3 }
|
||
|
||
|
||
awcDot11QoSTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11QoSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This (conceptual) table of attributes shall be a set of
|
||
parameters for each traffic category (i.e. 802.1D priority)
|
||
of packet passed over the radio."
|
||
::= { awcDot11mac 4 }
|
||
|
||
awcDot11QoSEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11QoSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An Entry (conceptual row) in the Aironet Quality of
|
||
Service Table.
|
||
|
||
ifIndex - Each 802.11 interface is represented by an
|
||
ifEntry. Interface tables in this MIB module are indexed
|
||
by ifIndex."
|
||
|
||
INDEX { ifIndex,
|
||
awcDot11QoSCoS}
|
||
::= { awcDot11QoSTable 1 }
|
||
|
||
AwcDot11QoSEntry ::= SEQUENCE {
|
||
awcDot11QoSCoS INTEGER,
|
||
awcDot11QoSCWmin INTEGER,
|
||
awcDot11QoSCWmax INTEGER
|
||
}
|
||
|
||
|
||
awcDot11QoSCoS OBJECT-TYPE
|
||
SYNTAX INTEGER (1..8)
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The auxiliary variable used to identify instances
|
||
of the columnar objects in the Aironet Quality of
|
||
Service Table. This variable corresponds directly to
|
||
the 802.1D traffic category ID, plus 1."
|
||
::= { awcDot11QoSEntry 1 }
|
||
|
||
awcDot11QoSCWmin OBJECT-TYPE
|
||
SYNTAX INTEGER (0..1023)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"802.11 CWmin of the traffic category. The value of this OID
|
||
must be one of the set 0, 1, 3, 7, 15, 31, 63, 127, 255, 511,
|
||
or 1023, and must be less than or equal to awcDot11QoSCWmax."
|
||
::= { awcDot11QoSEntry 2 }
|
||
|
||
awcDot11QoSCWmax OBJECT-TYPE
|
||
SYNTAX INTEGER (1..1023)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"802.11 CWmax of the traffic category. The value of this OID
|
||
must be one of the set 1, 3, 7, 15, 31, 63, 127, 255, 511,
|
||
or 1023, and must be greater than or equal to awcDot11QoSCWmin."
|
||
::= { awcDot11QoSEntry 3 }
|
||
|
||
|
||
awcDot11res OBJECT IDENTIFIER ::= {awc802dot11 3}
|
||
|
||
awcDot11resAttribute OBJECT IDENTIFIER ::= {awcDot11res 1}
|
||
|
||
awcDot11ResourceInfoTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11ResourceInfoEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Resource Info Table attributes. In tabular
|
||
form to allow for multiple instances on an
|
||
agent."
|
||
::= { awcDot11resAttribute 2 }
|
||
|
||
awcDot11ResourceInfoEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11ResourceInfoEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11ResourceInfoTable
|
||
table."
|
||
INDEX {ifIndex}
|
||
::= { awcDot11ResourceInfoTable 1 }
|
||
|
||
AwcDot11ResourceInfoEntry ::=
|
||
SEQUENCE {
|
||
awcDot11FirmwareBootstrapVersion DisplayString
|
||
}
|
||
|
||
awcDot11FirmwareBootstrapVersion OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The firmware version of the radio boot block.
|
||
Max. string length is 128 octets."
|
||
::= { awcDot11ResourceInfoEntry 1 }
|
||
|
||
awcDot11phy OBJECT IDENTIFIER ::= {awc802dot11 4}
|
||
|
||
awcDot11PhyOperationTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11PhyOperationEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcDot11PhyOperationTable attributes. In
|
||
tabular form to allow for multiple instances
|
||
on an agent."
|
||
::= { awcDot11phy 1 }
|
||
|
||
awcDot11PhyOperationEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11PhyOperationEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11PhyOperationTable
|
||
table."
|
||
INDEX {ifIndex}
|
||
::= { awcDot11PhyOperationTable 1 }
|
||
|
||
AwcDot11PhyOperationEntry ::=
|
||
SEQUENCE {
|
||
awcDot11CurrentCarrierSet INTEGER,
|
||
awcDot11ModulationType INTEGER,
|
||
awcDot11PreambleType INTEGER,
|
||
awcDot11PHYType INTEGER
|
||
}
|
||
|
||
awcDot11CurrentCarrierSet OBJECT-TYPE
|
||
SYNTAX INTEGER {usa(0), europe(1), japan(2), spain(3),
|
||
france(4), belgium(5), israel(6),
|
||
canada(7), australia(8), japanWide(9),
|
||
usa5GHz(11), europe5GHz(12), japan5GHz(13),
|
||
singapore5GHz(14), taiwan5GHz(15), china(16)}
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The carrier set of the device. The Carrier
|
||
Set implies a Regulatory Domain, but
|
||
geographic-specific restrictions within a
|
||
Regulatory Domain may necessitate several
|
||
Carrier Sets within the Regulatory Domain."
|
||
::= { awcDot11PhyOperationEntry 1 }
|
||
|
||
awcDot11ModulationType OBJECT-TYPE
|
||
SYNTAX INTEGER {standard(1), mok(2)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The RF modulation of the radio."
|
||
DEFVAL { standard }
|
||
::= { awcDot11PhyOperationEntry 2 }
|
||
|
||
awcDot11PreambleType OBJECT-TYPE
|
||
SYNTAX INTEGER {long(1), short(2)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current radio preamble type in use by the
|
||
Station.
|
||
Possible values:
|
||
1 = Use long preambles whenever possible.
|
||
2 = Use only short preambles."
|
||
::= { awcDot11PhyOperationEntry 3 }
|
||
|
||
awcDot11PHYType OBJECT-TYPE
|
||
SYNTAX INTEGER {fhss(1), dsss(2), irbaseband(3), dsssDot11A(11)}
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
|
||
"This is an 8-bit integer value that identifies the PHY type
|
||
supported by the attached PLCP and PMD. Currently defined
|
||
values and their corresponding PHY types are:
|
||
|
||
FHSS 2.4 GHz = 01 , DSSS 2.4 GHz = 02, IR Baseband = 03,
|
||
DSSS 5.0 GHz = 11"
|
||
|
||
::= { awcDot11PhyOperationEntry 5 }
|
||
|
||
|
||
awcDot11PhyFHSSTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11PhyFHSSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcDot11PhyFHSSTable attributes. In tabular
|
||
form to allow for multiple instances on an
|
||
agent."
|
||
::= { awcDot11phy 4 }
|
||
|
||
awcDot11PhyFHSSEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11PhyFHSSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11PhyFHSSTable table."
|
||
INDEX {ifIndex}
|
||
::= { awcDot11PhyFHSSTable 1 }
|
||
|
||
AwcDot11PhyFHSSEntry ::=
|
||
SEQUENCE {
|
||
awcDot11Compatible3100 TruthValue
|
||
}
|
||
|
||
awcDot11Compatible3100 OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Boolean on whether or not the Station should
|
||
use 1Mb/sec management frames to be compatible
|
||
with Aironet 3100 series radios."
|
||
DEFVAL { false }
|
||
::= { awcDot11PhyFHSSEntry 1 }
|
||
|
||
|
||
awcDot11PhyDSSSTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11PhyDSSSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcDot11PhyDSSSTable attributes. In tabular
|
||
form to allow for multiple instances on an
|
||
agent."
|
||
::= { awcDot11phy 5 }
|
||
|
||
awcDot11PhyDSSSEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11PhyDSSSEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the awcDot11PhyDSSSTable table."
|
||
INDEX {ifIndex}
|
||
::= { awcDot11PhyDSSSTable 1 }
|
||
|
||
AwcDot11PhyDSSSEntry ::=
|
||
SEQUENCE {
|
||
awcDot11Compatible4500 TruthValue,
|
||
awcDot11ChannelAutoImplemented TruthValue,
|
||
awcDot11ChannelAutoEnabled TruthValue,
|
||
awcDot11CurrentChannel INTEGER
|
||
}
|
||
|
||
awcDot11Compatible4500 OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Boolean on whether or not the Station should
|
||
use 2Mb/sec management frames to be compatible
|
||
with Aironet 4500 series radios."
|
||
DEFVAL { false }
|
||
::= { awcDot11PhyDSSSEntry 1 }
|
||
|
||
awcDot11ChannelAutoImplemented OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the radio can, when
|
||
awcDot11StationRole is roleAP, scan for other
|
||
BSS activity on all channels available in the
|
||
current awcDot11CurrentCarrierSet before
|
||
establishing its own BSS. If false, the radio
|
||
can only establish its BSS on
|
||
dot11CurrentChannel."
|
||
::= { awcDot11PhyDSSSEntry 2 }
|
||
|
||
awcDot11ChannelAutoEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true and awcDot11StationRole is roleAP, the
|
||
radio will scan for other BSS activity on all
|
||
channels available in the current
|
||
awcDot11CurrentCarrierSet before establishing
|
||
its own BSS. After the scan, this station
|
||
will establish its own BSS on the channel it
|
||
considers to have the least probability of
|
||
congestion. If false, this station always
|
||
establishes its BSS on dot11CurrentChannel."
|
||
DEFVAL { false }
|
||
::= { awcDot11PhyDSSSEntry 3 }
|
||
|
||
awcDot11CurrentChannel OBJECT-TYPE
|
||
SYNTAX INTEGER (1..14)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current operating frequency channel of the DSSS
|
||
PHY, as selected either by selective scanning or
|
||
via dot11CurrentChannel. Valid channel numbers
|
||
are as defined in 15.4.6.2"
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, IEEE802dot11-MIB."
|
||
::= { awcDot11PhyDSSSEntry 4 }
|
||
|
||
awcDot11SupportedDataRatesPrivacyTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11SupportedDataRatesPrivacyEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"For each transmit and receive bit rate, whether or not
|
||
the radio can support WEP encryption at that rate."
|
||
|
||
::= { awcDot11phy 11 }
|
||
|
||
awcDot11SupportedDataRatesPrivacyEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11SupportedDataRatesPrivacyEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An Entry (conceptual row) in the
|
||
awcDot11SupportedDataRatesPrivacy Table.
|
||
|
||
ifIndex - Each 802.11 interface is represented by an
|
||
ifEntry. Interface tables in this MIB module are indexed
|
||
by ifIndex."
|
||
|
||
INDEX {ifIndex, awcDot11SupportedDataRatesPrivacyIndex}
|
||
|
||
::= { awcDot11SupportedDataRatesPrivacyTable 1 }
|
||
|
||
AwcDot11SupportedDataRatesPrivacyEntry ::= SEQUENCE {
|
||
awcDot11SupportedDataRatesPrivacyIndex Integer32,
|
||
awcDot11SupportedDataRatesPrivacyValue Integer32,
|
||
awcDot11SupportedDataRatesPrivacyImplemented
|
||
TruthValue
|
||
}
|
||
|
||
awcDot11SupportedDataRatesPrivacyIndex OBJECT-TYPE
|
||
SYNTAX Integer32 (1..8)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Index object which identifies which data rate to access.
|
||
Range is 1..8."
|
||
::= { awcDot11SupportedDataRatesPrivacyEntry 1 }
|
||
|
||
awcDot11SupportedDataRatesPrivacyValue OBJECT-TYPE
|
||
SYNTAX Integer32 (2..127)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The receive or transmit bit rates supported by the PLCP
|
||
and PMD, represented by a count from X<>02-X<>7f,
|
||
corresponding to data rates in increments of 500Kb/s from
|
||
1 Mb/s to 63.5 Mb/s."
|
||
|
||
::= { awcDot11SupportedDataRatesPrivacyEntry 2 }
|
||
|
||
awcDot11SupportedDataRatesPrivacyImplemented OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Whether or not WEP encryption is supported by the radio
|
||
for both Transmit and Receive operations at the
|
||
corresponding bit rate specified by
|
||
awcDot11SupportedDataRatesPrivacyValue."
|
||
::= { awcDot11SupportedDataRatesPrivacyEntry 3 }
|
||
|
||
awcDot11ChanSelectTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11ChanSelectEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This table specifies for each 802.11 channel,
|
||
whether the scanning process controlled by the
|
||
awcDot11ChannelAutoEnabled can select a
|
||
particular channel for use. This table has an
|
||
expansion dependent relationship on the ifTable.
|
||
For each entry in this table, there exists at least
|
||
an entry in the ifTable of ifType ieee80211(71).
|
||
Entries in this table cannot be created or deleted
|
||
by the network management system. All entries are
|
||
created or deleted by the agent."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 15.4.6.2."
|
||
::= { awcDot11phy 12 }
|
||
|
||
awcDot11ChanSelectEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11ChanSelectEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Each entry specifies if a particular radio channel
|
||
is enabled on a radio interface."
|
||
INDEX {ifIndex,
|
||
awcDot11ChanSelectChannel}
|
||
|
||
::= { awcDot11ChanSelectTable 1 }
|
||
|
||
AwcDot11ChanSelectEntry ::= SEQUENCE {
|
||
awcDot11ChanSelectChannel INTEGER,
|
||
awcDot11ChanSelectEnable TruthValue
|
||
}
|
||
|
||
awcDot11ChanSelectChannel OBJECT-TYPE
|
||
SYNTAX INTEGER (1..14)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"802.11 channel which is a candidate for low-occupancy
|
||
scanning."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, section 15.4.6.2."
|
||
::= { awcDot11ChanSelectEntry 1 }
|
||
|
||
awcDot11ChanSelectEnable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, awcDot11ChanSelectChannel is available for the
|
||
system to use as its awcDot11CurrentChannel after scanning
|
||
for channel occupancy. If false, awcDot11ChanSelectChannel
|
||
is not available."
|
||
REFERENCE
|
||
"IEEE Std 802.11-Jan 14 1999, Wireless LAN Medium
|
||
Access Control and Physical Layer Specifications,
|
||
LAN MAN Standards Committee of the IEEE Computer
|
||
Society, IEEE802dot11-MIB."
|
||
DEFVAL { true }
|
||
::= { awcDot11ChanSelectEntry 2 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of awc802dot11 parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcUserMgr parameters
|
||
-- ********************************************************************
|
||
userMgrConfigTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF UserMgrConfigEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System User attributes."
|
||
::= { awcUserMgr 1 }
|
||
|
||
userMgrConfigEntry OBJECT-TYPE
|
||
SYNTAX UserMgrConfigEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the user manager table."
|
||
INDEX {userMgrUserIndex}
|
||
::= { userMgrConfigTable 1 }
|
||
|
||
UserMgrConfigEntry ::=
|
||
SEQUENCE {
|
||
userMgrUserIndex Unsigned32,
|
||
userMgrUserName DisplayString,
|
||
userMgrPassword OCTET STRING,
|
||
userMgrCapabilities Unsigned32,
|
||
userMgrStatus RowStatus
|
||
}
|
||
|
||
userMgrUserIndex OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The index of the user."
|
||
::= { userMgrConfigEntry 1 }
|
||
|
||
userMgrUserName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..32))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of the user. This should be unique
|
||
across all users. Max. string length is 32
|
||
octets."
|
||
::= { userMgrConfigEntry 2 }
|
||
|
||
userMgrPassword OBJECT-TYPE
|
||
SYNTAX OCTET STRING (SIZE(0..24))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The SHA-1 hashed password of the user in the
|
||
user manager. When a plaintext password is
|
||
written, it is automatically replaced by the
|
||
SHA-1 Secure Hash of that plaintext, prefixed
|
||
by a 4-octet magic cookie. Max. string length
|
||
is 24 octets."
|
||
::= { userMgrConfigEntry 3 }
|
||
|
||
userMgrCapabilities OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Bitmask of the capabilities of the user.
|
||
The value may be any combination (sum)
|
||
of the following capability values:
|
||
0 = none
|
||
1 = Administrator
|
||
2 = Write
|
||
4 = Firmware Update
|
||
8 = Identity Update
|
||
16 = SNMP Community"
|
||
::= { userMgrConfigEntry 4 }
|
||
|
||
userMgrStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the user. Allows deletion via SNMP."
|
||
::= { userMgrConfigEntry 5 }
|
||
|
||
enableUserMgr OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the User Manager subsystem is active.
|
||
Web page, console, and SNMP access is
|
||
restricted in accordance with
|
||
userMgrCapabilities. If false, all users have
|
||
full access to the system. "
|
||
DEFVAL { false }
|
||
::= { awcUserMgr 2 }
|
||
|
||
allowBrowseWithoutLogin OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the HTTP user interface to read-only
|
||
web pages can be accessed without passing
|
||
HTTP authentication. If false, any HTTP
|
||
access requires the user to pass HTTP
|
||
authentication."
|
||
DEFVAL { true }
|
||
::= { awcUserMgr 3 }
|
||
|
||
protectLegalPage OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should the legal credits page be protected or
|
||
not."
|
||
DEFVAL { false }
|
||
::= { awcUserMgr 4 }
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcUserMgr parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcHttpd parameters
|
||
-- ********************************************************************
|
||
defaultWebRoot OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"File directory which contains the system's
|
||
web site root file index.shm. Max. string
|
||
length is 128 octets."
|
||
DEFVAL { "mfs0:/StdUI/" }
|
||
::= { awcHttpd 1 }
|
||
|
||
defaultHelpRoot OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"URL identifying the directory in which help
|
||
pages for the system are located. This URL
|
||
is prefixed to all help page links.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/air/ap3xx" }
|
||
::= { awcHttpd 2 }
|
||
|
||
getWebUI OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of an auxilliary set of HTML user
|
||
interface files to be loaded at system boot
|
||
time from defaultFileServer. Archive
|
||
formats accepted include .tar and .tar.gz.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcHttpd 3 }
|
||
|
||
cmdInvokeGetWebUI OBJECT-TYPE
|
||
SYNTAX AwcInvokeCommand
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Initiate loading of the getWebUI file.
|
||
|
||
Commands recognized: start."
|
||
|
||
::= { awcHttpd 4 }
|
||
|
||
cmdStatusGetWebUI OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Status of the most recent command to load
|
||
the auxilliary web User Interface pages.
|
||
Possible values:
|
||
0 = Operation completed successfully (or
|
||
has not taken place).
|
||
2 = File not found on the file server.
|
||
12 = Insufficient memory to load all
|
||
files.
|
||
20 = Identifier encountered while decoding
|
||
is an ordinary file,
|
||
not a directory.
|
||
22 = No file specified, or invalid file
|
||
format.
|
||
35 = File format is not supported.
|
||
68 = Operation is still in progress. Poll
|
||
again later.
|
||
72 = Operation was started, but later was
|
||
canceled."
|
||
::= { awcHttpd 5 }
|
||
|
||
awcHttpdPort OBJECT-TYPE
|
||
SYNTAX INTEGER (1..65535)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IP port number over which to perform HTTP
|
||
operations."
|
||
DEFVAL { 80 }
|
||
::= { awcHttpd 6 }
|
||
|
||
awcConsoleAutoApply OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current state of 'auto apply' mode on the
|
||
console browser."
|
||
DEFVAL { true }
|
||
::= { awcHttpd 7 }
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcHttpd parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcDnsRes parameters
|
||
-- ********************************************************************
|
||
resolverDomain OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of the resolver domain currently in
|
||
use by the system. Max. string length of 128
|
||
octets."
|
||
DEFVAL { "" }
|
||
::= { awcDnsRes 1 }
|
||
|
||
resolverDomainSuffix OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The suffix name of the resolver domain. Used
|
||
to abbreviate displayed host names.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcDnsRes 2 }
|
||
|
||
resolverDomainServerTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF ResolverDomainServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of DNS Name Servers currently in use by
|
||
the system."
|
||
::= { awcDnsRes 3 }
|
||
|
||
resolverDomainServerEntry OBJECT-TYPE
|
||
SYNTAX ResolverDomainServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in resolverDomainServerTable."
|
||
INDEX {resolverDomainServerPriority}
|
||
::= { resolverDomainServerTable 1 }
|
||
|
||
ResolverDomainServerEntry ::=
|
||
SEQUENCE {
|
||
resolverDomainServerPriority INTEGER,
|
||
resolverDomainServer DisplayString}
|
||
|
||
resolverDomainServerPriority OBJECT-TYPE
|
||
SYNTAX INTEGER (1..3)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The priority order in which a domain name
|
||
server is queried."
|
||
::= { resolverDomainServerEntry 1 }
|
||
|
||
resolverDomainServer OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IP Address of a domain name server
|
||
currently in use by the system."
|
||
::= { resolverDomainServerEntry 2 }
|
||
|
||
defaultResolverDomain OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of the resolver domain to be used by
|
||
the system unless overridden by a BOOTP or
|
||
DHCP server. Max. string length of 128
|
||
octets."
|
||
DEFVAL { "" }
|
||
::= { awcDnsRes 4 }
|
||
|
||
defaultResolverDomainServerTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF DefaultResolverDomainServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of DNS Name Servers to be used by the
|
||
system unless overridden by a BOOTP or DHCP
|
||
server."
|
||
::= { awcDnsRes 5 }
|
||
|
||
defaultResolverDomainServerEntry OBJECT-TYPE
|
||
SYNTAX DefaultResolverDomainServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in defaultResolverDomainServerTable."
|
||
INDEX {defaultResolverDomainServerPriority}
|
||
::= { defaultResolverDomainServerTable 1 }
|
||
|
||
DefaultResolverDomainServerEntry ::=
|
||
SEQUENCE {
|
||
defaultResolverDomainServerPriority
|
||
INTEGER,
|
||
defaultResolverDomainServer DisplayString}
|
||
|
||
defaultResolverDomainServerPriority OBJECT-TYPE
|
||
SYNTAX INTEGER (1..3)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The priority order in which a domain name
|
||
server is queried."
|
||
::= { defaultResolverDomainServerEntry 1 }
|
||
|
||
defaultResolverDomainServer OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IP Address of a domain name server to be
|
||
used by the system unless overridden by a
|
||
BOOTP or DHCP server."
|
||
::= { defaultResolverDomainServerEntry 2 }
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcDnsRes parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcSnmp parameters
|
||
-- ********************************************************************
|
||
snmpTrapDest OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The destination of an SNMP trap. This may be
|
||
any DNS-recognizable IP address. Max. string
|
||
length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcSnmp 1 }
|
||
|
||
snmpTrapCommunity OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The community name of the trap.
|
||
Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcSnmp 2 }
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcSnmp parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcSntp parameters
|
||
-- ********************************************************************
|
||
defaultSntpServer OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of the SNTP server to be use by the
|
||
system, unless overridden by a BOOTP or DHCP
|
||
server. Max. string length is 128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcSntp 1 }
|
||
|
||
sntpServer OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name of the SNTP server currently in use
|
||
by the system. Max. string length is 128
|
||
octets."
|
||
::= { awcSntp 2 }
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcSntp parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcForwardTbl parameters
|
||
-- ********************************************************************
|
||
awcFtStatistics OBJECT IDENTIFIER ::= {awcForwardTbl 1}
|
||
|
||
awcFtMcastAddr OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of multicast addresses observed by the
|
||
system."
|
||
::= { awcFtStatistics 1 }
|
||
|
||
awcFtDsHost OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of DS (infrastructure) host addresses
|
||
observed by the system over its own DS network
|
||
interface (Ethernet)."
|
||
::= { awcFtStatistics 3 }
|
||
|
||
awcFtBridgeHost OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of DS (infrastructure) host addresses
|
||
observed by the system on the remote side of
|
||
a bridge."
|
||
::= { awcFtStatistics 5 }
|
||
|
||
awcFtClientSTA OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of Client Station addresses observed by
|
||
the system."
|
||
::= { awcFtStatistics 7 }
|
||
|
||
awcFtClientSTASelf OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of Client Stations which are Associated
|
||
to the system."
|
||
::= { awcFtStatistics 8 }
|
||
|
||
awcFtBridge OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of non-root Bridge addresses observed by
|
||
the system."
|
||
::= { awcFtStatistics 9 }
|
||
|
||
awcFtBridgeSelf OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of non-root Bridges which are Associated
|
||
to the system."
|
||
::= { awcFtStatistics 10 }
|
||
|
||
awcFtRepeater OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of Repeater addresses observed by the
|
||
system."
|
||
::= { awcFtStatistics 11 }
|
||
|
||
awcFtRepeaterSelf OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of Repeater devices which are Associated
|
||
to the system."
|
||
::= { awcFtStatistics 12 }
|
||
|
||
awcFtAccessPoint OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of Access Point addresses observed by
|
||
the system."
|
||
::= { awcFtStatistics 13 }
|
||
|
||
awcFtBridgeRoot OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Count of Root Bridge addresses observed by
|
||
the system."
|
||
::= { awcFtStatistics 15 }
|
||
|
||
|
||
awcFtConfig OBJECT IDENTIFIER ::= {awcForwardTbl 2}
|
||
|
||
awcFtMaxNumEntries OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum number of entries in the
|
||
forwarding table. Must be a power of 2 from
|
||
1024 to 65536. The number of entries controls
|
||
the size of the forwarding table and the hash
|
||
algorithm used by the forwarding table.
|
||
Changing the number of entries requires a
|
||
system reboot."
|
||
DEFVAL { 8192 }
|
||
::= { awcFtConfig 1 }
|
||
|
||
awcFtTimeoutSecUnknown OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=unknown will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 300 }
|
||
::= { awcFtConfig 2 }
|
||
|
||
awcFtTimeoutSecMcastAddr OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=multicast will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 28800 }
|
||
::= { awcFtConfig 3 }
|
||
|
||
awcFtTimeoutSecDsHost OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=dsHost will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 1800 }
|
||
::= { awcFtConfig 4 }
|
||
|
||
awcFtTimeoutSecBridgeHost OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=bridgeHost will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 1800 }
|
||
::= { awcFtConfig 5 }
|
||
|
||
awcFtTimeoutSecClientSTA OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=clientStation will remain in
|
||
the Forwarding Table before being staled-out."
|
||
DEFVAL { 1800 }
|
||
::= { awcFtConfig 6 }
|
||
|
||
awcFtTimeoutSecBridge OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=bridge will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 28800 }
|
||
::= { awcFtConfig 7 }
|
||
|
||
awcFtTimeoutSecRepeater OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=repeater will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 28800 }
|
||
::= { awcFtConfig 8 }
|
||
|
||
awcFtTimeoutSecAccessPoint OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=accessPoint will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 28800 }
|
||
::= { awcFtConfig 9 }
|
||
|
||
awcFtTimeoutSecBridgeRoot OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The default number of seconds an Entry with
|
||
awcTpFdbClassID=bridgeRoot will remain in the
|
||
Forwarding Table before being staled-out."
|
||
DEFVAL { 28800 }
|
||
::= { awcFtConfig 10 }
|
||
|
||
awcFtEnableAwcTpFdbTable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the system will populate the
|
||
awcTpFdbEntry MIB for all forwarding table
|
||
entries. This improves management statistics.
|
||
If false, the system will not populate the
|
||
awcTpFdbEntry MIB for any forwarding table
|
||
entries. This improves speed and memory
|
||
utilization."
|
||
DEFVAL { true }
|
||
::= { awcFtConfig 11 }
|
||
|
||
awcFtEnableMacAuthServer OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the system will contact a AAA server
|
||
for retrieving dot1dStaticTable information
|
||
for new forwarding table entries if a
|
||
dot1dStaticTable entry does not already exist
|
||
for the host address."
|
||
DEFVAL { false }
|
||
::= { awcFtConfig 12 }
|
||
|
||
awcFtRogueApAlertTimeout OBJECT-TYPE
|
||
SYNTAX INTEGER (0..1440)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The minimum number of minutes after a Possible
|
||
Rogue status is reported about a device before
|
||
another Possible Rogue status report is
|
||
issued by this system about the same device."
|
||
DEFVAL { 30 }
|
||
::= { awcFtConfig 13 }
|
||
|
||
awcFtEnableMacOrEapAuth OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the system grants full access to those
|
||
clients which have successfully completed either
|
||
MAC or EAP authentication."
|
||
DEFVAL { false }
|
||
::= { awcFtConfig 14 }
|
||
|
||
awcFtDot1dTpFdbTableEnable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the system will populate the
|
||
dot1dTpFdbEntry MIB for all forwarding table
|
||
entries. This improves management statistics.
|
||
If false, the system will not populate the
|
||
dot1dTpFdbEntry MIB for any forwarding table
|
||
entries. This improves speed and memory
|
||
utilization."
|
||
DEFVAL { true }
|
||
::= { awcFtConfig 15 }
|
||
|
||
awcFtEnableMcastMapping OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the system will map multicast forwarding
|
||
table entries to the broadcast entry.
|
||
This improves speed and memory utilization.
|
||
If false, the system will create an entry
|
||
for each unique multicast address. This improves
|
||
management statistics and allows filtering of
|
||
specific multicast addresses."
|
||
DEFVAL { false }
|
||
::= { awcFtConfig 16 }
|
||
|
||
|
||
AwcTpFdbClassID ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Description of the general 802.11 classification of a host."
|
||
SYNTAX INTEGER { unknown(1), multicast(2), dsHost(3),
|
||
bridgeHost(4), clientStation(5), bridge(6),
|
||
repeater(7), accessPoint(8), bridgeRoot(9) }
|
||
|
||
awcTpFdbTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcTpFdbEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A table that contains information about
|
||
entries for which the bridge has forwarding
|
||
and/or filtering information. This information
|
||
is used by the transparent bridging function
|
||
for maintaining statistics about each entry."
|
||
::= { awcForwardTbl 3 }
|
||
|
||
awcTpFdbEntry OBJECT-TYPE
|
||
SYNTAX AwcTpFdbEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Information about a specific MAC address
|
||
for which the bridge has some forwarding and/or
|
||
filtering information."
|
||
INDEX { awcTpFdbAddress }
|
||
::= { awcTpFdbTable 1 }
|
||
|
||
AwcTpFdbEntry ::=
|
||
SEQUENCE {
|
||
awcTpFdbAddress MacAddress,
|
||
awcTpFdbClassID AwcTpFdbClassID,
|
||
awcTpFdbSrcPktsImmed Counter32,
|
||
awcTpFdbSrcOctetsImmed Counter32,
|
||
awcTpFdbSrcErrorPktsImmed Counter32,
|
||
awcTpFdbSrcErrorOctetsImmed Counter32,
|
||
awcTpFdbDestPktsImmed Counter32,
|
||
awcTpFdbDestOctetsImmed Counter32,
|
||
awcTpFdbDestErrorPktsImmed Counter32,
|
||
awcTpFdbDestErrorOctetsImmed Counter32,
|
||
awcTpFdbDestMaxRetryErrorsImmed Counter32,
|
||
awcTpFdbIPv4Addr IpAddress
|
||
}
|
||
|
||
awcTpFdbAddress OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A MAC address for which the bridge has
|
||
forwarding and/or filtering information."
|
||
::= { awcTpFdbEntry 1 }
|
||
|
||
awcTpFdbClassID OBJECT-TYPE
|
||
SYNTAX AwcTpFdbClassID
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Observed general 802.11 classification of the
|
||
entry."
|
||
::= { awcTpFdbEntry 2 }
|
||
|
||
awcTpFdbSrcPktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed packets for which this entry was the
|
||
source."
|
||
::= { awcTpFdbEntry 3 }
|
||
|
||
awcTpFdbSrcOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed octets for which this entry was the
|
||
source."
|
||
::= { awcTpFdbEntry 4 }
|
||
|
||
awcTpFdbSrcErrorPktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed error packets for which this entry was
|
||
the source."
|
||
::= { awcTpFdbEntry 5 }
|
||
|
||
awcTpFdbSrcErrorOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed error octets for which this entry was
|
||
the source."
|
||
::= { awcTpFdbEntry 6 }
|
||
|
||
awcTpFdbDestPktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed packets for which this entry was the
|
||
destination."
|
||
::= { awcTpFdbEntry 7 }
|
||
|
||
awcTpFdbDestOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed octets for which this entry was the
|
||
destination."
|
||
::= { awcTpFdbEntry 8 }
|
||
|
||
awcTpFdbDestErrorPktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed error packets for which this entry was
|
||
the destination. This count includes
|
||
awcTpFdbDestMaxRetryErrorsImmed."
|
||
::= { awcTpFdbEntry 9 }
|
||
|
||
awcTpFdbDestErrorOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed error octets for which this entry was
|
||
the destination."
|
||
::= { awcTpFdbEntry 10 }
|
||
|
||
awcTpFdbDestMaxRetryErrorsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of observed max-retry error packets for which this
|
||
entry was the destination."
|
||
::= { awcTpFdbEntry 11 }
|
||
|
||
awcTpFdbIPv4Addr OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Observed IPv4 network address of the entry."
|
||
::= { awcTpFdbEntry 16 }
|
||
|
||
|
||
AwcDdpProdDevID ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Aironet DDP Product Device ID of a host."
|
||
SYNTAX INTEGER {
|
||
tokenRingAP(74),
|
||
ethernetAP(76),
|
||
ethernetBridge(77),
|
||
tokenRingBridge(78),
|
||
pc3000Client(84),
|
||
serialUC(85),
|
||
ethernetUC(86),
|
||
pc3500Client(101),
|
||
pc4500Client(102),
|
||
generic80211Client(104),
|
||
pc4800Client(109),
|
||
pc3100Client(110),
|
||
mc(111),
|
||
ethernetClient(112),
|
||
pc2500Client(113),
|
||
pc4800bClient(117),
|
||
euc(120),
|
||
homeAP(121),
|
||
eucNoDiversity(122),
|
||
emcNoDiversity(123),
|
||
emc(124),
|
||
series350Client(127),
|
||
series370Client(128),
|
||
multicast(240),
|
||
unknown(241),
|
||
tokenRingHost(253),
|
||
ethernetHost(255)
|
||
}
|
||
|
||
AwcDdpRadioDevID ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Aironet DDP Radio Device ID of a host."
|
||
SYNTAX INTEGER {
|
||
unknown(0),
|
||
tma900(1),
|
||
tma2400(2),
|
||
pc3500(3),
|
||
pc3000(4),
|
||
tma2040(5),
|
||
pc4500(6),
|
||
pc4800(12),
|
||
pc3100(13),
|
||
series350(34),
|
||
series370(35)
|
||
}
|
||
|
||
awcTpFdbDdpTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcTpFdbDdpEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A table that contains information about
|
||
entries for which the bridge has forwarding
|
||
and/or filtering information. This table
|
||
maintains only Aironet-specific information
|
||
about each entry."
|
||
::= { awcForwardTbl 4 }
|
||
|
||
awcTpFdbDdpEntry OBJECT-TYPE
|
||
SYNTAX AwcTpFdbDdpEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Information about a specific MAC address
|
||
for which the bridge has some forwarding and/or
|
||
filtering information."
|
||
INDEX { awcTpFdbDdpAddress }
|
||
::= { awcTpFdbDdpTable 1 }
|
||
|
||
AwcTpFdbDdpEntry ::=
|
||
SEQUENCE {
|
||
awcTpFdbDdpAddress MacAddress,
|
||
awcTpFdbDdpSysName DisplayString,
|
||
awcTpFdbDdpProdDevID AwcDdpProdDevID,
|
||
awcTpFdbDdpRadioDevID AwcDdpRadioDevID,
|
||
awcTpFdbDdpSwVerMajor INTEGER,
|
||
awcTpFdbDdpSwVerMinor INTEGER,
|
||
awcTpFdbDdpSwVerBeta INTEGER,
|
||
awcTpFdbDdpUptime Unsigned32,
|
||
awcTpFdbDdpNumAnnounceSent Unsigned32,
|
||
awcTpFdbDdpNumAssociated INTEGER,
|
||
awcTpFdbDdpLoad INTEGER,
|
||
awcTpFdbDdpDistFromDS INTEGER
|
||
}
|
||
|
||
awcTpFdbDdpAddress OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A MAC address for which the bridge has
|
||
forwarding and/or filtering information."
|
||
::= { awcTpFdbDdpEntry 1 }
|
||
|
||
awcTpFdbDdpSysName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE (0..255))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Aironet DDP System Name of the entry."
|
||
::= { awcTpFdbDdpEntry 2 }
|
||
|
||
awcTpFdbDdpProdDevID OBJECT-TYPE
|
||
SYNTAX AwcDdpProdDevID
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Aironet DDP Product Device ID of the entry."
|
||
::= { awcTpFdbDdpEntry 3 }
|
||
|
||
awcTpFdbDdpRadioDevID OBJECT-TYPE
|
||
SYNTAX AwcDdpRadioDevID
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Aironet DDP Radio Device ID of the entry."
|
||
::= { awcTpFdbDdpEntry 4 }
|
||
|
||
awcTpFdbDdpSwVerMajor OBJECT-TYPE
|
||
SYNTAX INTEGER (0..255)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Aironet DDP Major Software Version Number of
|
||
the entry. If unknown, the value 0 is returned."
|
||
::= { awcTpFdbDdpEntry 5 }
|
||
|
||
awcTpFdbDdpSwVerMinor OBJECT-TYPE
|
||
SYNTAX INTEGER (0..255)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Aironet DDP Minor Software Version Number of
|
||
the entry."
|
||
::= { awcTpFdbDdpEntry 6 }
|
||
|
||
awcTpFdbDdpSwVerBeta OBJECT-TYPE
|
||
SYNTAX INTEGER (0..255)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Aironet DDP Beta Software Version Number of
|
||
the entry. This number is always 0 for
|
||
officially-released software."
|
||
::= { awcTpFdbDdpEntry 7 }
|
||
|
||
awcTpFdbDdpUptime OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The time in seconds that the entry has been
|
||
operational."
|
||
::= { awcTpFdbDdpEntry 8 }
|
||
|
||
awcTpFdbDdpNumAnnounceSent OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of times the entry itself believes
|
||
that it has issued some form of Aironet DDP
|
||
Presense Announcement. If this field decreases,
|
||
the entry has probably been reset."
|
||
::= { awcTpFdbDdpEntry 9 }
|
||
|
||
awcTpFdbDdpNumAssociated OBJECT-TYPE
|
||
SYNTAX INTEGER (0..2007)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of Stations currently Associated
|
||
with the entry."
|
||
::= { awcTpFdbDdpEntry 10 }
|
||
|
||
awcTpFdbDdpLoad OBJECT-TYPE
|
||
SYNTAX INTEGER (0..100)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An approximation of the percentage of offered
|
||
vs. theoretically-available load on the host's
|
||
radio interface."
|
||
::= { awcTpFdbDdpEntry 11 }
|
||
|
||
awcTpFdbDdpDistFromDS OBJECT-TYPE
|
||
SYNTAX INTEGER (0..255)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The Bridging Distance or Number of Hops between
|
||
the entry and the backbone Distribution System
|
||
(DS). If 0, the entry is directly connected to
|
||
the DS."
|
||
::= { awcTpFdbDdpEntry 12 }
|
||
|
||
|
||
AwcDot11ClientState ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IEEE 802.11 Station Service State.
|
||
|
||
state0 =
|
||
Station not able to send any frames whatsoever.
|
||
It is most likely not yet configured.
|
||
state1 =
|
||
Station can send Class 1 frames. It is
|
||
Unauthenticated and Unassociated.
|
||
state2 =
|
||
Station can send Class 2 frames. It is
|
||
Authenticated, but is as yet Unassociated.
|
||
state3 =
|
||
Station can send Class 3 frames. It is both
|
||
Authenticated and Associated."
|
||
SYNTAX INTEGER {
|
||
state0(1),
|
||
state1(2),
|
||
state2(3),
|
||
state3(4)
|
||
}
|
||
|
||
awcDot11TpFdbTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot11TpFdbEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A table that contains information about
|
||
entries for which the bridge has forwarding
|
||
and/or filtering information. This table
|
||
maintains only 802.11-specific information
|
||
about each entry."
|
||
::= { awcForwardTbl 5 }
|
||
|
||
awcDot11TpFdbEntry OBJECT-TYPE
|
||
SYNTAX AwcDot11TpFdbEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Information about a specific MAC address
|
||
for which the bridge has some forwarding and/or
|
||
filtering information."
|
||
INDEX { awcDot11TpFdbAddress }
|
||
::= { awcDot11TpFdbTable 1 }
|
||
|
||
AwcDot11TpFdbEntry ::=
|
||
SEQUENCE {
|
||
awcDot11TpFdbAddress MacAddress,
|
||
awcDot11TpFdbAID Unsigned32,
|
||
awcDot11TpFdbClientState AwcDot11ClientState,
|
||
awcDot11TpFdbTxShortRetries Counter32,
|
||
awcDot11TpFdbTxLongRetries Counter32,
|
||
awcDot11TpFdbLatestTxShortRetries Counter32,
|
||
awcDot11TpFdbLatestTxLongRetries Counter32,
|
||
awcDot11TpFdbRxWEPErrors Counter32,
|
||
awcDot11TpFdbLatestRxSignalStrength Unsigned32,
|
||
awcDot11TpFdbLatestRxSignalQuality Unsigned32,
|
||
awcDot11TpFdbCapabilities Unsigned32,
|
||
awcDot11TpFdbListenInterval Unsigned32,
|
||
awcDot11TpFdbSupportedDataRates OCTET STRING,
|
||
awcDot11TpFdbPreferredTxRate Unsigned32,
|
||
awcDot11TpFdbCurrentBSS MacAddress,
|
||
awcDot11TpFdbSSID INTEGER,
|
||
awcDot11TpFdbVlanId AwcVlanId
|
||
}
|
||
|
||
awcDot11TpFdbAddress OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A MAC address for which the bridge has
|
||
forwarding and/or filtering information."
|
||
::= { awcDot11TpFdbEntry 1 }
|
||
|
||
awcDot11TpFdbAID OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"AID with which the Station is associated with this
|
||
system, or 2008 if the
|
||
Station is not currently known to be associated. If the
|
||
entry is multicast, awcDot11TpFdbAID is 0. Note that
|
||
the uplink from a Client or Repeater AP to its parent
|
||
is always AID 1."
|
||
::= { awcDot11TpFdbEntry 2 }
|
||
|
||
awcDot11TpFdbClientState OBJECT-TYPE
|
||
SYNTAX AwcDot11ClientState
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"802.11 Service State of the Station."
|
||
::= { awcDot11TpFdbEntry 3 }
|
||
|
||
awcDot11TpFdbTxShortRetries OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of 802.11 Short Retries incurred across
|
||
all packet Transmission Attempts to this Station."
|
||
::= { awcDot11TpFdbEntry 4 }
|
||
|
||
awcDot11TpFdbTxLongRetries OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of 802.11 Long Retries incurred across
|
||
all packet Transmission Attempts to this Station."
|
||
::= { awcDot11TpFdbEntry 5 }
|
||
|
||
awcDot11TpFdbLatestTxShortRetries OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of 802.11 Short Retries incurred during the
|
||
most recent packet Transmission Attempts to this Station."
|
||
::= { awcDot11TpFdbEntry 6 }
|
||
|
||
awcDot11TpFdbLatestTxLongRetries OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of 802.11 Long Retries incurred during the
|
||
most recent packet Transmission Attempts to this Station."
|
||
::= { awcDot11TpFdbEntry 7 }
|
||
|
||
awcDot11TpFdbRxWEPErrors OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of packets received from this Station
|
||
which failed to be properly decrypted via the WEP security
|
||
mechanism."
|
||
::= { awcDot11TpFdbEntry 8 }
|
||
|
||
awcDot11TpFdbLatestRxSignalStrength OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A device-dependent measure of the signal strength of the
|
||
most recently received packet from this Station. Might be
|
||
normalized or unnormalized."
|
||
::= { awcDot11TpFdbEntry 9 }
|
||
|
||
awcDot11TpFdbLatestRxSignalQuality OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A device-dependent measure of the signal quality of the
|
||
most recently received packet from this Station."
|
||
::= { awcDot11TpFdbEntry 10 }
|
||
|
||
awcDot11TpFdbCapabilities OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The possible 802.11 capabilities of the Station's radio."
|
||
::= { awcDot11TpFdbEntry 11 }
|
||
|
||
awcDot11TpFdbListenInterval OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The number of beacon intervals across which a the Station
|
||
will sleep in power-save mode, or 1 if the
|
||
Station will never be in power-save mode."
|
||
::= { awcDot11TpFdbEntry 12 }
|
||
|
||
awcDot11TpFdbSupportedDataRates OBJECT-TYPE
|
||
SYNTAX OCTET STRING (SIZE(1..126))
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This attribute shall specify the set of data rates
|
||
at which the station may transmit data. Each octet
|
||
contains a value representing a rate. Each rate
|
||
shall be within the range from 2 to 255, the lower
|
||
seven bits 0..6 of which corresponding to data rates
|
||
in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s,
|
||
and shall be supported (as indicated in the supported
|
||
rates table) for receiving data. This value is
|
||
reported in transmitted Beacon, Probe Request, Probe
|
||
Response, Association Request, Association Response,
|
||
Reassociation Request, and Reassociation Response
|
||
frames, and is used to determine whether a BSS
|
||
with which the station desires to synchronize is
|
||
suitable. If set, Bit 7 of the rate specification
|
||
indicates that rate is a member of the Basic Rate Set
|
||
of the access point."
|
||
::= { awcDot11TpFdbEntry 13 }
|
||
|
||
awcDot11TpFdbPreferredTxRate OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The transmission rate at which a packet should
|
||
currently be transmitted from an AP to this Station.
|
||
This rate does not carry information about whether or
|
||
not the rate is in the Basic Rate Set (i.e. bit 0x80
|
||
is never set)."
|
||
::= { awcDot11TpFdbEntry 14 }
|
||
|
||
awcDot11TpFdbCurrentBSS OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"BSS to which the station is currently Associated, or
|
||
00:00:00:00:00:00 if the station's current AP is
|
||
unknown."
|
||
::= { awcDot11TpFdbEntry 15 }
|
||
|
||
awcDot11TpFdbSSID OBJECT-TYPE
|
||
SYNTAX INTEGER (-1..2007)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If the Station is Associated to this AP, the SSID via
|
||
which the Station Associated. If 0, the Station
|
||
Associated via dot11DesiredSSID. If greater than 0,
|
||
the Station Associated through the auxiliary SSID with
|
||
awcDot11AuxSSIDIndex equal to awcDot11TpFdbSSID.
|
||
If -1, the Station is not currently Associated to
|
||
this AP."
|
||
::= { awcDot11TpFdbEntry 16 }
|
||
|
||
awcDot11TpFdbVlanId OBJECT-TYPE
|
||
SYNTAX AwcVlanId
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Numeric ID of the VLAN over which the Station is
|
||
communicating. If 0, the Station is not known to be
|
||
communicating over any specific VLAN."
|
||
::= { awcDot11TpFdbEntry 17 }
|
||
|
||
|
||
awcDot1dTpPortTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDot1dTpPortEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A table that contains information about every
|
||
port that is associated with this transparent
|
||
bridge. This table contains information about
|
||
host and protocol filtering for the port.
|
||
Each entry represents a transparent bridge port
|
||
on the device.
|
||
Entries in this table cannot be created or
|
||
deleted by the network management system.
|
||
All entries are created or deleted by the
|
||
agent."
|
||
::= { awcForwardTbl 6 }
|
||
|
||
awcDot1dTpPortEntry OBJECT-TYPE
|
||
SYNTAX AwcDot1dTpPortEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A list of filtering information for each port of a
|
||
transparent bridge. This information includes
|
||
packet forwarding permission for unicast and
|
||
non-unicast frames and filters ID used for
|
||
the filtering."
|
||
INDEX { dot1dTpPort }
|
||
::= { awcDot1dTpPortTable 1 }
|
||
|
||
AwcDot1dTpPortEntry ::=
|
||
SEQUENCE {
|
||
awcDot1dTpPortDefaultUcastAllowedToGoTo OCTET STRING,
|
||
awcDot1dTpPortDefaultNUcastAllowedToGoTo OCTET STRING,
|
||
awcDot1dTpPortMaxNUcastPerSecond Unsigned32,
|
||
awcDot1dTpPortDefaultInEthertypeFilterId Unsigned32,
|
||
awcDot1dTpPortDefaultOutEthertypeFilterId Unsigned32,
|
||
awcDot1dTpPortDefaultInIpProtoFilterId Unsigned32,
|
||
awcDot1dTpPortDefaultOutIpProtoFilterId Unsigned32,
|
||
awcDot1dTpPortDefaultInIpPortFilterId Unsigned32,
|
||
awcDot1dTpPortDefaultOutIpPortFilterId Unsigned32
|
||
}
|
||
|
||
awcDot1dTpPortDefaultUcastAllowedToGoTo OBJECT-TYPE
|
||
SYNTAX OCTET STRING
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The set of ports to which frames received from a
|
||
specific port and destined for a unicast MAC address
|
||
which is not already listed in dot1dStaticTable are
|
||
allowed to be forwarded. Each octet
|
||
within the value of this object specifies a set of
|
||
eight ports, with the first octet specifying ports
|
||
1 through 8, the second octet specifying ports 9
|
||
through 16, etc. Within each octet, the most
|
||
significant bit represents the lowest numbered
|
||
port, and the least significant bit represents the
|
||
highest numbered port. Thus, each port of the
|
||
bridge is represented by a single bit within the
|
||
value of this object. If that bit has a value of
|
||
'1' then that port is included in the set of
|
||
ports; the port is not included if its bit has a
|
||
value of '0'. (Note that the setting of the bit
|
||
corresponding to the port from which a frame is
|
||
received is irrelevant.) The default value of
|
||
this object is a string of ones of appropriate
|
||
length."
|
||
::= { awcDot1dTpPortEntry 1 }
|
||
|
||
awcDot1dTpPortDefaultNUcastAllowedToGoTo OBJECT-TYPE
|
||
SYNTAX OCTET STRING
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The set of ports to which frames received from a
|
||
specific port and destined for a multicast MAC address
|
||
which is not already listed in dot1dStaticTable are
|
||
allowed to be forwarded. Each octet
|
||
within the value of this object specifies a set of
|
||
eight ports, with the first octet specifying ports
|
||
1 through 8, the second octet specifying ports 9
|
||
through 16, etc. Within each octet, the most
|
||
significant bit represents the lowest numbered
|
||
port, and the least significant bit represents the
|
||
highest numbered port. Thus, each port of the
|
||
bridge is represented by a single bit within the
|
||
value of this object. If that bit has a value of
|
||
'1' then that port is included in the set of
|
||
ports; the port is not included if its bit has a
|
||
value of '0'. (Note that the setting of the bit
|
||
corresponding to the port from which a frame is
|
||
received is irrelevant.) The default value of
|
||
this object is a string of ones of appropriate
|
||
length."
|
||
::= { awcDot1dTpPortEntry 2 }
|
||
|
||
awcDot1dTpPortMaxNUcastPerSecond OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum number of multicast packets
|
||
allowed to be forwarded over the port each
|
||
second. If 0, the number of multicasts
|
||
is unlimited."
|
||
DEFVAL { 0 }
|
||
::= { awcDot1dTpPortEntry 3 }
|
||
|
||
awcDot1dTpPortDefaultInEthertypeFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfEtSetId of the Ethertype Filter Set to
|
||
apply to packets received over this port.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcDot1dTpPortEntry 4 }
|
||
|
||
awcDot1dTpPortDefaultOutEthertypeFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfEtSetId of the Ethertype Filter Set to
|
||
apply to packets transmitted over this port.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcDot1dTpPortEntry 5 }
|
||
|
||
awcDot1dTpPortDefaultInIpProtoFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIppSetId of the IP Protocol Filter Set to
|
||
apply to packets received over this port.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcDot1dTpPortEntry 6 }
|
||
|
||
awcDot1dTpPortDefaultOutIpProtoFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIppSetId of the IP Protocol Filter Set to
|
||
apply to packets transmitted over this port.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcDot1dTpPortEntry 7 }
|
||
|
||
awcDot1dTpPortDefaultInIpPortFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIptSetId of the IP Port Filter Set to
|
||
apply to packets received over this port.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcDot1dTpPortEntry 8 }
|
||
|
||
awcDot1dTpPortDefaultOutIpPortFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIptSetId of the IP Port Filter Set to
|
||
apply to packets transmitted over this port.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcDot1dTpPortEntry 9 }
|
||
|
||
|
||
awcTpFdbAlertTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcTpFdbAlertEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A table that contains information about
|
||
entries for which the bridge has forwarding
|
||
and/or filtering information. This table
|
||
maintains only packet-trace alert statistics.
|
||
Each entry is indexed by a MAC address
|
||
in the packet forwarding.
|
||
Entries in this table cannot be created or
|
||
deleted by the network management system.
|
||
All entries are created or deleted by the
|
||
agent."
|
||
::= { awcForwardTbl 7 }
|
||
|
||
awcTpFdbAlertEntry OBJECT-TYPE
|
||
SYNTAX AwcTpFdbAlertEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Information about a specific MAC address
|
||
for which the bridge has some forwarding and/or
|
||
filtering information."
|
||
INDEX { awcTpFdbAlertAddress }
|
||
::= { awcTpFdbAlertTable 1 }
|
||
|
||
AwcTpFdbAlertEntry ::=
|
||
SEQUENCE {
|
||
awcTpFdbAlertAddress MacAddress,
|
||
awcTpFdbFromAlertSrcPktsImmed Counter32,
|
||
awcTpFdbFromAlertSrcOctetsImmed Counter32,
|
||
awcTpFdbToAlertDestPktsImmed Counter32,
|
||
awcTpFdbToAlertDestOctetsImmed Counter32,
|
||
awcTpFdbAlertSentAlertTypePktsImmed Counter32,
|
||
awcTpFdbAlertSentAlertTypeOctetsImmed Counter32,
|
||
awcTpFdbAlertRcvdAlertTypePktsImmed Counter32,
|
||
awcTpFdbAlertRcvdAlertTypeOctetsImmed Counter32
|
||
}
|
||
|
||
awcTpFdbAlertAddress OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A MAC address for which the bridge has
|
||
forwarding and/or filtering information."
|
||
::= { awcTpFdbAlertEntry 1 }
|
||
|
||
awcTpFdbFromAlertSrcPktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of packets directed to this entry,
|
||
over any interface, from a source host
|
||
designated Alert From in the forwarding table."
|
||
::= { awcTpFdbAlertEntry 2 }
|
||
|
||
awcTpFdbFromAlertSrcOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of octets directed to this entry,
|
||
over any interface, from a source host
|
||
designated Alert From in the forwarding table."
|
||
::= { awcTpFdbAlertEntry 3 }
|
||
|
||
awcTpFdbToAlertDestPktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of packets sent by this entry,
|
||
over any interface, to a destination MAC address
|
||
designated Alert To in the forwarding table."
|
||
::= { awcTpFdbAlertEntry 4 }
|
||
|
||
awcTpFdbToAlertDestOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of packets sent by this entry,
|
||
over any interface, to a destination MAC address
|
||
designated Alert To in the forwarding table."
|
||
::= { awcTpFdbAlertEntry 5 }
|
||
|
||
awcTpFdbAlertSentAlertTypePktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of packets sent by this entry,
|
||
over any interface, with a packet type
|
||
designated Alert in an applicable protocol filter."
|
||
::= { awcTpFdbAlertEntry 6 }
|
||
|
||
awcTpFdbAlertSentAlertTypeOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of octets sent by this entry,
|
||
over any interface, with a packet type
|
||
designated Alert in an applicable protocol filter."
|
||
::= { awcTpFdbAlertEntry 7 }
|
||
|
||
awcTpFdbAlertRcvdAlertTypePktsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of packets directed to this entry,
|
||
over any interface, with a packet type
|
||
designated Alert in an applicable protocol filter."
|
||
::= { awcTpFdbAlertEntry 8 }
|
||
|
||
awcTpFdbAlertRcvdAlertTypeOctetsImmed OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total number of octets directed to this entry,
|
||
over any interface, with a packet type
|
||
designated Alert in an applicable protocol filter."
|
||
::= { awcTpFdbAlertEntry 9 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcForwardTbl parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcEventLog parameters
|
||
-- ********************************************************************
|
||
|
||
AwcEventSeverity ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Severity of an event handled within the system."
|
||
SYNTAX INTEGER { systemFatal(2),
|
||
protocolFatal(3),
|
||
portFatal(4),
|
||
systemAlert(5),
|
||
protocolAlert(6),
|
||
portAlert(7),
|
||
externalAlert(8),
|
||
systemWarning(9),
|
||
protocolWarning(10),
|
||
portWarning(11),
|
||
externalWarning(12),
|
||
systemInfo(13),
|
||
protocolInfo(14),
|
||
portInfo(15),
|
||
externalInfo(16)
|
||
}
|
||
|
||
|
||
|
||
awcEventOffsetGMT OBJECT-TYPE
|
||
SYNTAX Integer32 (-720..720)
|
||
UNITS "minutes"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current offset from GMT in minutes."
|
||
DEFVAL { -300 }
|
||
::= { awcEventLog 1 }
|
||
|
||
awcEventUseDaylightSavingsTime OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, daylight savings time is used."
|
||
DEFVAL { true }
|
||
::= { awcEventLog 2 }
|
||
|
||
awcEventTimestampGMT OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"GMT Time, in seconds since January 1, 1970,
|
||
when the system wall-clock time was last set."
|
||
DEFVAL { 0 }
|
||
::= { awcEventLog 3 }
|
||
|
||
awcEventUptimeModifiedGMT OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System uptime, in seconds, when the system
|
||
wall-clock time was last set."
|
||
::= { awcEventLog 4 }
|
||
|
||
awcEventDisplayWallClockTime OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, time display on the system's web
|
||
pages and console is in wall-clock time.
|
||
If false, time display is in system uptime."
|
||
DEFVAL { true }
|
||
::= { awcEventLog 5 }
|
||
|
||
awcEventDisplayUptimeAscending OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, time display in system uptime is
|
||
measured from the time the system boots,
|
||
forward. If false, time display in
|
||
measured from the current time backwards."
|
||
DEFVAL { true }
|
||
::= { awcEventLog 6 }
|
||
|
||
awcEventDetailDefault OBJECT-TYPE
|
||
SYNTAX Integer32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Detail level at which, by default, events
|
||
are displayed. General detail level
|
||
classifications are:
|
||
8 - no display at all
|
||
16 - sparse detail
|
||
24 - normal detail
|
||
32 - verbose detail
|
||
40 - exhaustive detail
|
||
"
|
||
DEFVAL { 24 }
|
||
::= { awcEventLog 7 }
|
||
|
||
awcEventSeverityDispConsole OBJECT-TYPE
|
||
SYNTAX AwcEventSeverity
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If an event has a severity level greater than
|
||
or equal to awcEventSeverityDispConsole, it
|
||
is displayed on the console shortly after it
|
||
occurs."
|
||
DEFVAL { externalInfo }
|
||
::= { awcEventLog 8 }
|
||
|
||
awcEventSeverityDispHtmlGUI OBJECT-TYPE
|
||
SYNTAX AwcEventSeverity
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If an event has a severity level greater than
|
||
or equal to awcEventSeverityDispHtmlGUI, it
|
||
is displayed on the the Event Log GUI web
|
||
pages."
|
||
DEFVAL { externalInfo }
|
||
::= { awcEventLog 9 }
|
||
|
||
awcEventSeverityDispHtmlConsole OBJECT-TYPE
|
||
SYNTAX AwcEventSeverity
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If an event has a severity level greater than
|
||
or equal to awcEventSeverityDispHtmlConsole,
|
||
it is displayed on the the Event Log console
|
||
browser pages."
|
||
DEFVAL { externalInfo }
|
||
::= { awcEventLog 10 }
|
||
|
||
awcEventAlertSNMP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, events of a severity with Disposition
|
||
set to notify will generate an SNMP trap."
|
||
DEFVAL { true }
|
||
::= { awcEventLog 11 }
|
||
|
||
awcEventAlertSyslog OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, events of a severity with Disposition
|
||
set to notify will generate a sysLog message."
|
||
DEFVAL { true }
|
||
::= { awcEventLog 12 }
|
||
|
||
awcEventStatistics OBJECT IDENTIFIER ::= {awcEventLog 14}
|
||
|
||
awcEventCntSeverityNULL OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"NULL message counter."
|
||
::= { awcEventStatistics 1 }
|
||
|
||
awcEventCntSeveritySilent OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Silent message counter."
|
||
::= { awcEventStatistics 2 }
|
||
|
||
awcEventCntSeveritySystemFatal OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Fatal system message counter."
|
||
::= { awcEventStatistics 3 }
|
||
|
||
awcEventCntSeverityProtocolFatal OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Fatal Protocol message counter."
|
||
::= { awcEventStatistics 4 }
|
||
|
||
awcEventCntSeverityPortFatal OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Fatal Port message counter."
|
||
::= { awcEventStatistics 5 }
|
||
|
||
awcEventCntSeveritySystemAlert OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System Alert message counter."
|
||
::= { awcEventStatistics 6 }
|
||
|
||
awcEventCntSeverityProtocolAlert OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Protocol Alert message counter."
|
||
::= { awcEventStatistics 7 }
|
||
|
||
awcEventCntSeverityPortAlert OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Port Alert message counter."
|
||
::= { awcEventStatistics 8 }
|
||
|
||
awcEventCntSeverityExternalAlert OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"External Alert message counter."
|
||
::= { awcEventStatistics 9 }
|
||
|
||
awcEventCntSeveritySystemWarning OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System Warning message counter."
|
||
::= { awcEventStatistics 10 }
|
||
|
||
awcEventCntSeverityProtocolWarning OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Protocol Warning message counter."
|
||
::= { awcEventStatistics 11 }
|
||
|
||
awcEventCntSeverityPortWarning OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Port Warning message counter."
|
||
::= { awcEventStatistics 12 }
|
||
|
||
awcEventCntSeverityExternalWarning OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"External Warning message counter."
|
||
::= { awcEventStatistics 13 }
|
||
|
||
awcEventCntSeveritySystemInfo OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System Info message counter."
|
||
::= { awcEventStatistics 14 }
|
||
|
||
awcEventCntSeverityProtocolInfo OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Protocol Info message counter."
|
||
::= { awcEventStatistics 15 }
|
||
|
||
awcEventCntSeverityPortInfo OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Port Info message counter."
|
||
::= { awcEventStatistics 16 }
|
||
|
||
awcEventCntSeverityExternalInfo OBJECT-TYPE
|
||
SYNTAX Counter32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"External Info message counter."
|
||
::= { awcEventStatistics 17 }
|
||
|
||
|
||
awcEventDisposition OBJECT IDENTIFIER ::= {awcEventLog 15}
|
||
|
||
awcEventDispSeverityNULL OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"NULL message disposition."
|
||
::= { awcEventDisposition 1 }
|
||
|
||
awcEventDispSeveritySilent OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Silent message disposition."
|
||
::= { awcEventDisposition 2 }
|
||
|
||
awcEventDispSeveritySystemFatal OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Fatal system message disposition."
|
||
::= { awcEventDisposition 3 }
|
||
|
||
awcEventDispSeverityProtocolFatal OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Fatal Protocol message disposition."
|
||
::= { awcEventDisposition 4 }
|
||
|
||
awcEventDispSeverityPortFatal OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Fatal Port message disposition."
|
||
::= { awcEventDisposition 5 }
|
||
|
||
awcEventDispSeveritySystemAlert OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System Alert message disposition."
|
||
::= { awcEventDisposition 6 }
|
||
|
||
awcEventDispSeverityProtocolAlert OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Protocol Alert message disposition."
|
||
::= { awcEventDisposition 7 }
|
||
|
||
awcEventDispSeverityPortAlert OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Port Alert message disposition."
|
||
::= { awcEventDisposition 8 }
|
||
|
||
awcEventDispSeverityExternalAlert OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"External Alert message disposition."
|
||
::= { awcEventDisposition 9 }
|
||
|
||
awcEventDispSeveritySystemWarning OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System Warning message disposition."
|
||
::= { awcEventDisposition 10 }
|
||
|
||
awcEventDispSeverityProtocolWarning OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Protocol Warning message disposition."
|
||
::= { awcEventDisposition 11 }
|
||
|
||
awcEventDispSeverityPortWarning OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Port Warning message disposition."
|
||
::= { awcEventDisposition 12 }
|
||
|
||
awcEventDispSeverityExternalWarning OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"External Warning message disposition."
|
||
::= { awcEventDisposition 13 }
|
||
|
||
awcEventDispSeveritySystemInfo OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System Info message disposition."
|
||
::= { awcEventDisposition 14 }
|
||
|
||
awcEventDispSeverityProtocolInfo OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Protocol Info message disposition."
|
||
::= { awcEventDisposition 15 }
|
||
|
||
awcEventDispSeverityPortInfo OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Port Info message disposition."
|
||
::= { awcEventDisposition 16 }
|
||
|
||
awcEventDispSeverityExternalInfo OBJECT-TYPE
|
||
SYNTAX AwcEventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"External Info message disposition."
|
||
::= { awcEventDisposition 17 }
|
||
|
||
awcEventSyslogAddr OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The destination of a sysLog message.
|
||
This address must be numeric or DNS
|
||
resolvable. Max. string length is
|
||
128 octets."
|
||
DEFVAL { "" }
|
||
::= { awcEventLog 16 }
|
||
|
||
awcEventSyslogFacility OBJECT-TYPE
|
||
SYNTAX INTEGER (0..8191)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The facility number encoded within a sysLog
|
||
message."
|
||
DEFVAL { 16 }
|
||
::= { awcEventLog 17 }
|
||
|
||
awcEventTraceStationSeverity OBJECT-TYPE
|
||
SYNTAX AwcEventSeverity
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Severity at which all Detailed Packet Trace events
|
||
shall be handled."
|
||
DEFVAL { externalInfo }
|
||
::= { awcEventLog 20 }
|
||
|
||
awcEventTraceLogSize OBJECT-TYPE
|
||
SYNTAX Unsigned32 (0..8388608)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Size in octets of the system Detailed Event Trace
|
||
Buffer. Note that this buffer is statically
|
||
allocated at system initialization time. Changing
|
||
the size of the buffer requires a system reboot."
|
||
DEFVAL { 0 }
|
||
::= { awcEventLog 21 }
|
||
|
||
awcEventTracePacketLen OBJECT-TYPE
|
||
SYNTAX Unsigned32 (0..2312)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Maximum size in octets of each Packet Trace Event
|
||
recorded in the Detailed Event Trace Buffer."
|
||
DEFVAL { 0 }
|
||
::= { awcEventLog 22 }
|
||
|
||
awcEventTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcEventEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"SNMP access to Event Log table."
|
||
::= { awcEventLog 23 }
|
||
|
||
awcEventEntry OBJECT-TYPE
|
||
SYNTAX AwcEventEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in awcEventTable."
|
||
INDEX { awcEventID }
|
||
::= { awcEventTable 1 }
|
||
|
||
AwcEventEntry ::=
|
||
SEQUENCE {
|
||
awcEventID Unsigned32,
|
||
awcEventTime DisplayString,
|
||
awcEventSeverity AwcEventSeverity,
|
||
awcEventDescription DisplayString,
|
||
awcEventType DisplayString }
|
||
|
||
awcEventID OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System-unique identifier of the event."
|
||
::= { awcEventEntry 1 }
|
||
|
||
awcEventTime OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"System time at which the event occurred."
|
||
::= { awcEventEntry 2 }
|
||
|
||
awcEventSeverity OBJECT-TYPE
|
||
SYNTAX AwcEventSeverity
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Severity of the event."
|
||
::= { awcEventEntry 3 }
|
||
|
||
awcEventDescription OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Detailed description of the event."
|
||
::= { awcEventEntry 4 }
|
||
|
||
awcEventType OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specific type of the event. The type is unique for
|
||
each test condition which can result in event
|
||
generation."
|
||
::= { awcEventEntry 5 }
|
||
|
||
|
||
awcEventUseCiscoFormat OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the system will generate
|
||
syslog messages using Cisco standard EMBLEM-
|
||
compliant format. If false, syslog will use
|
||
legacy Aironet format."
|
||
DEFVAL { false }
|
||
::= { awcEventLog 25 }
|
||
|
||
|
||
awcDot11AuthenticateFailDisposition OBJECT-TYPE
|
||
SYNTAX AwcDot11EventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specifies how standard IEEE trap dot11AuthenticateFail
|
||
is handled on the system."
|
||
DEFVAL { eventLogAndIeeeTrap}
|
||
::= { awcEventLog 26 }
|
||
|
||
|
||
awcDot11DeauthenticateDisposition OBJECT-TYPE
|
||
SYNTAX AwcDot11EventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specifies how standard IEEE 802.11 trap dot11Deauthenticate
|
||
is handled on the system."
|
||
DEFVAL { eventLogAndIeeeTrap}
|
||
::= { awcEventLog 27 }
|
||
|
||
|
||
awcDot11DisassociateDisposition OBJECT-TYPE
|
||
SYNTAX AwcDot11EventDisposition
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Specifies how standard IEEE 802.11 trap dot11Disassociate
|
||
is handled on the system."
|
||
DEFVAL { eventLogAndIeeeTrap}
|
||
::= { awcEventLog 28 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcEtherMIB parameters
|
||
-- ********************************************************************
|
||
awcEtherIfSpeedSelect OBJECT-TYPE
|
||
SYNTAX INTEGER { tenBaseT(3),
|
||
oneHundredBaseT(5),
|
||
tenBaseTfull(6),
|
||
oneHundredBaseTfull(7),
|
||
autoDetect(8) }
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Requested Ethernet interface speed and
|
||
duplex."
|
||
DEFVAL { autoDetect }
|
||
::= { awcEtherMIB 1 }
|
||
|
||
awcEtherDuplex OBJECT-TYPE
|
||
SYNTAX INTEGER { half(1), full(2) }
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Actual Ethernet interface duplex, after any
|
||
line negotiation has taken place."
|
||
::= { awcEtherMIB 5 }
|
||
|
||
awcEtherCamSize OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of entries in the hardware Content Addressible
|
||
Memory MAC address filter available to the Ethernet
|
||
controller."
|
||
::= { awcEtherMIB 7 }
|
||
|
||
awcEtherEnableSwCam OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Ethernet driver makes use of a Software
|
||
Content Addressible Memory when making packet-forwarding
|
||
decisions. When true, forwarding decisions are much
|
||
faster, but network statistics collection is much
|
||
coarser. If false, all packet-forwarding decisions are
|
||
made by the higher-level packet-bridging logic."
|
||
DEFVAL { false }
|
||
::= { awcEtherMIB 8 }
|
||
|
||
awcEtherForcePortUnblock OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Ethernet port has dot1dStpPortState forced
|
||
to forwarding even when the Spanning Tree Protocol is
|
||
not enabled. This provides rapid port re-establishment
|
||
at the potential cost of not detecting network topology
|
||
loops involving the Ethernet and other network interfaces
|
||
such as the radio. If false, the Ethernet port is blocked
|
||
whenever there exists the potential for a network topology
|
||
loop and the Spanning Tree Protocol is not enabled to guard
|
||
against such loops."
|
||
DEFVAL { false }
|
||
::= { awcEtherMIB 9 }
|
||
|
||
awcEtherLostEthernetSeconds OBJECT-TYPE
|
||
SYNTAX INTEGER (1..10000)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Number of seconds the system must detect loss of backbone
|
||
connectivity (i.e. loss of Ethernet link and no active
|
||
trunks available on any of the radios) before taking the
|
||
action specified by awcEtherLostEthernetAction."
|
||
DEFVAL { 2 }
|
||
::= { awcEtherMIB 10 }
|
||
|
||
awcEtherLostEthernetAction OBJECT-TYPE
|
||
SYNTAX INTEGER { noAction(1), switchRepeater(2), radioOff(3),
|
||
restrictSSID(4) }
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Action taken by the system when a loss of backbone
|
||
connectivity condition occurs for a period of time
|
||
longer than awcEtherLostEthernetSeconds."
|
||
DEFVAL { switchRepeater }
|
||
::= { awcEtherMIB 11 }
|
||
|
||
awcEtherLostEthernetSSID OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The single SSID index required by the system if
|
||
awcEtherLostEthernetAction is restrictSSID and backbone
|
||
connectivity is lost for a period of time longer than
|
||
awcEtherLostEthernetSeconds. If 0, only Association to
|
||
dot11DesiredSSID is allowed. If non-0, only
|
||
Association to the auxiliary SSID with the corresponding
|
||
awcDot11AuxSSIDIndex is allowed."
|
||
DEFVAL { 0 }
|
||
::= { awcEtherMIB 12 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcPolicyGroups parameters
|
||
-- ********************************************************************
|
||
|
||
awcPolGrpTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcPolGrpEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of named groups of related protocol filters"
|
||
::= { awcPolicyGroups 1 }
|
||
|
||
awcPolGrpEntry OBJECT-TYPE
|
||
SYNTAX AwcPolGrpEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in awcPolGrpTable."
|
||
INDEX {awcPolGrpId}
|
||
::= { awcPolGrpTable 1 }
|
||
|
||
AwcPolGrpEntry ::=
|
||
SEQUENCE {
|
||
awcPolGrpId Unsigned32,
|
||
awcPolGrpName DisplayString,
|
||
awcPolGrpStatus RowStatus,
|
||
awcPolGrpInEthertypeFilterId Unsigned32,
|
||
awcPolGrpOutEthertypeFilterId Unsigned32,
|
||
awcPolGrpInIpProtoFilterId Unsigned32,
|
||
awcPolGrpOutIpProtoFilterId Unsigned32,
|
||
awcPolGrpInIpPortFilterId Unsigned32,
|
||
awcPolGrpOutIpPortFilterId Unsigned32
|
||
}
|
||
|
||
awcPolGrpId OBJECT-TYPE
|
||
SYNTAX Unsigned32 (1..1023)
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Numeric identifier of the Policy Group."
|
||
::= { awcPolGrpEntry 1 }
|
||
|
||
awcPolGrpName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..64))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Descriptive name of the Policy Group.
|
||
Max. string length is 64 octets."
|
||
::= { awcPolGrpEntry 2 }
|
||
|
||
awcPolGrpStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the entire Policy Group."
|
||
::= { awcPolGrpEntry 3 }
|
||
|
||
awcPolGrpInEthertypeFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfEtSetId of the Ethertype Filter Set to
|
||
apply to packets received subject to this policy.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcPolGrpEntry 4 }
|
||
|
||
awcPolGrpOutEthertypeFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfEtSetId of the Ethertype Filter Set to
|
||
apply to packets transmitted subject to this policy.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcPolGrpEntry 5 }
|
||
|
||
awcPolGrpInIpProtoFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIppSetId of the IP Protocol Filter Set to
|
||
apply to packets received subject to this policy.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcPolGrpEntry 6 }
|
||
|
||
awcPolGrpOutIpProtoFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIppSetId of the IP Protocol Filter Set to
|
||
apply to packets transmitted subject to this policy.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcPolGrpEntry 7 }
|
||
|
||
awcPolGrpInIpPortFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIptSetId of the IP Port Filter Set to
|
||
apply to packets received subject to this policy.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcPolGrpEntry 8 }
|
||
|
||
awcPolGrpOutIpPortFilterId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"awcPfIptSetId of the IP Port Filter Set to
|
||
apply to packets transmitted subject to this policy.
|
||
If 0, no filters are applied."
|
||
DEFVAL { 0 }
|
||
::= { awcPolGrpEntry 9 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcDscpToCosMap parameters
|
||
-- ********************************************************************
|
||
|
||
awcDscpToCosMapEnable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, IP packets which are not already
|
||
classified with a non-default Class of Service
|
||
(CoS) can be classified by reference to their
|
||
Differentiated Services Code-Point (DSCP) value.
|
||
If false, unclassified IP packets are not subject
|
||
to DSCP classification."
|
||
DEFVAL { false }
|
||
::= { awcPolicyGroups 2 }
|
||
|
||
awcDscpToCosMapTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcDscpToCosMapEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This (conceptual) table to statically map
|
||
Differentiated Services Code-Point (DSCP)
|
||
values to corresponding Class of Service (CoS)
|
||
values."
|
||
::= { awcPolicyGroups 3 }
|
||
|
||
awcDscpToCosMapEntry OBJECT-TYPE
|
||
SYNTAX AwcDscpToCosMapEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An Entry (conceptual row) in the Aironet DSCP To CoS
|
||
mapping table to statically map a Differentiated
|
||
Services Code-Point (DSCP) value to corresponding
|
||
Class of Service (CoS) value."
|
||
|
||
INDEX { awcDscpToCosMapDscp }
|
||
|
||
::= { awcDscpToCosMapTable 1 }
|
||
|
||
|
||
AwcDscpToCosMapEntry ::= SEQUENCE {
|
||
awcDscpToCosMapDscp INTEGER,
|
||
awcDscpToCosMapCos INTEGER
|
||
}
|
||
|
||
awcDscpToCosMapDscp OBJECT-TYPE
|
||
SYNTAX INTEGER (1..64)
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The auxiliary variable used to identify instances
|
||
of the columnar objects in the Aironet Differentiated
|
||
Services Code-Point (DSCP) to Class of Service (CoS)
|
||
Mapping Table. This variable directly corresponds to
|
||
a Differentiated Services Code-Point, plus 1. The
|
||
value may be used for marking a traffic stream."
|
||
::= { awcDscpToCosMapEntry 1 }
|
||
|
||
awcDscpToCosMapCos OBJECT-TYPE
|
||
SYNTAX INTEGER (0..8)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"A value of Class of Service (CoS) mapped to
|
||
the DSCP value awcDscpToCosMapDscp. This object
|
||
corresponds directly to the 802.1D traffic category
|
||
ID, plus 1. The matching values are therefore in the
|
||
range 1 through 8. The value 0 indicates that no
|
||
matching CoS is configured for the corresponding
|
||
awcDscpToCosMapDscp."
|
||
::= { awcDscpToCosMapEntry 2 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcDdpIAPP parameters
|
||
-- ********************************************************************
|
||
awcIappMcastIpAddr OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Multicast IP network address over which
|
||
applicable packets of the DDP and IAPP
|
||
protocols are exchanged between stations.
|
||
Default 224.0.1.40."
|
||
DEFVAL { 'E0000128'H }
|
||
::= { awcDdpIAPP 1 }
|
||
|
||
awcIappPort OBJECT-TYPE
|
||
SYNTAX INTEGER (1..65535)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IP port identifier through which applicable
|
||
packets of the DDP and IAPP protocols are
|
||
exchanged between stations.
|
||
Default 2887."
|
||
DEFVAL { 2887 }
|
||
::= { awcDdpIAPP 2 }
|
||
|
||
awcP802dot1XVersion OBJECT-TYPE
|
||
SYNTAX INTEGER { d7(7), d8(8), d10(10) }
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Version of the 802.1X Protocol specification which
|
||
the AP will apply for incoming and outgoing EAPOL
|
||
traffic. Versions with 'd' designators are draft
|
||
specifications. The 802.1x-2001 standard is the
|
||
same as draft 10."
|
||
DEFVAL { d10 }
|
||
::= { awcDdpIAPP 100 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcHotStandby parameters
|
||
-- ********************************************************************
|
||
|
||
awcHotStandbyMACAddr OBJECT-TYPE
|
||
SYNTAX MacAddress
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The MAC address of the target unit which is
|
||
being monitored."
|
||
DEFVAL { '000000000000'H }
|
||
::= { awcHotStandby 1 }
|
||
|
||
awcHotStandbyPollingFrequency OBJECT-TYPE
|
||
SYNTAX INTEGER (1..30)
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The frequency (in seconds) that the monitored
|
||
target unit is being polled for testing its
|
||
health."
|
||
DEFVAL { 1 }
|
||
::= { awcHotStandby 2 }
|
||
|
||
awcHotStandbyPollingTimeOut OBJECT-TYPE
|
||
SYNTAX INTEGER (1..600)
|
||
UNITS "seconds"
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The total time (in seconds) that the monitoring
|
||
unit can tolerate the failure at polling the
|
||
monitored target unit. After this duration, one
|
||
more failure of the polling will trigger the
|
||
standby unit to take the role of monitored unit."
|
||
DEFVAL { 5 }
|
||
::= { awcHotStandby 3 }
|
||
|
||
awcHotStandbyInHotStandby OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the current unit is in its monitoring
|
||
mode, i.e., if the unit is or will be a hot
|
||
standby device."
|
||
DEFVAL { false }
|
||
::= { awcHotStandby 4 }
|
||
|
||
AwcHotStandbyState ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Hot standby state."
|
||
SYNTAX INTEGER {
|
||
running(0),
|
||
initializing(1),
|
||
stopped(2),
|
||
notRunning(3)
|
||
}
|
||
|
||
awcHotStandbyState OBJECT-TYPE
|
||
SYNTAX AwcHotStandbyState
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current state, e.g., running, stopped, ... of the hotstandby."
|
||
::= { awcHotStandby 5 }
|
||
|
||
awcHotStandbyStatus OBJECT-TYPE
|
||
SYNTAX AwcHotStandbyStatus
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The current stateus, e.g., error, OK, ... of the hotstandby."
|
||
::= { awcHotStandby 6 }
|
||
|
||
|
||
-- **********************************************************************
|
||
-- * awcAaa parameters
|
||
-- **********************************************************************
|
||
|
||
awcAaaServerTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcAaaServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This table provides information of AAA servers
|
||
currently available to this access point and
|
||
the parameters used to connect to the servers.
|
||
Each entry corresponds to an AAA server and is
|
||
indexed by the priority in which the server
|
||
should be used. AAA server of lowest priority
|
||
value should be used first. Entries in this
|
||
table cannot be created or deleted by the
|
||
network management system. All entries are
|
||
created or deleted by the agent."
|
||
::= { awcAaa 1 }
|
||
|
||
awcAaaServerEntry OBJECT-TYPE
|
||
SYNTAX AwcAaaServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry provide the AAA server usage priority,
|
||
protocol, name, IP port, request timeout, and
|
||
authentication mechanisms supported."
|
||
INDEX {awcAaaServerPriority}
|
||
::= { awcAaaServerTable 1 }
|
||
|
||
AwcAaaServerEntry ::=
|
||
SEQUENCE {
|
||
awcAaaServerPriority INTEGER,
|
||
awcAaaServerProtocol INTEGER,
|
||
awcAaaServerName DisplayString,
|
||
awcAaaServerPort Unsigned32,
|
||
awcAaaServerTimeout Unsigned32,
|
||
awcAaaClientName DisplayString,
|
||
awcAaaServerSharedSecret DisplayString,
|
||
awcAaaServer8021xCapabilityEnabled TruthValue,
|
||
awcAaaServerMacAddrAuthEnabled TruthValue,
|
||
awcAaaServerAdminAuthEnabled TruthValue,
|
||
awcAaaServerMipAuthEnabled TruthValue,
|
||
awcAaaServerMaxRetransmission Unsigned32 }
|
||
|
||
awcAaaServerPriority OBJECT-TYPE
|
||
SYNTAX INTEGER (1..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The priority of the server for when multiple servers
|
||
are configured for the same service. Lower priority
|
||
servers are used, in sequence, as backups."
|
||
::= { awcAaaServerEntry 1 }
|
||
|
||
awcAaaServerProtocol OBJECT-TYPE
|
||
SYNTAX INTEGER {radius(1), tacacsPlus(2)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The protocol used to communicate with the AAA server."
|
||
::= { awcAaaServerEntry 2 }
|
||
|
||
awcAaaServerName OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The DNS-resolvable name or numeric IP address of the
|
||
AAA server."
|
||
::= { awcAaaServerEntry 3 }
|
||
|
||
awcAaaServerPort OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IP port number of the AAA server."
|
||
::= { awcAaaServerEntry 4 }
|
||
|
||
awcAaaServerTimeout OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The amount of time (in seconds) that an Access Point
|
||
should wait for a response from the AAA server
|
||
before retransmitting the request. If the Access Point
|
||
does not receive a response within the timeout
|
||
period, it retransmits the request. If no response is
|
||
received for a maximum of awcAaaServerMaxRetransmission
|
||
retransmissions, the server is considered not reachable
|
||
and a secondary server (if any) will be chosen.
|
||
If the AP and the AAA server are connected through a
|
||
low-speed network and the awcAaaServerTimeout value is set
|
||
to too low, the network may become congested, as the AP
|
||
retransmits unacknowledged requests that have not yet
|
||
reached the server"
|
||
::= { awcAaaServerEntry 5 }
|
||
|
||
awcAaaClientName OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name the Access Point uses to identify itself when
|
||
acting as the supplicant."
|
||
::= { awcAaaServerEntry 6 }
|
||
|
||
awcAaaServerSharedSecret OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The textual string shared between the AAA server and
|
||
the access point, used to authenticate the messages
|
||
delivered between them."
|
||
::= { awcAaaServerEntry 7 }
|
||
|
||
awcAaaServer8021xCapabilityEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Is this server to be used for 802.1X authentication?"
|
||
::= { awcAaaServerEntry 8 }
|
||
|
||
awcAaaServerMacAddrAuthEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Is this server to be used for MAC-address
|
||
authentication?"
|
||
::= { awcAaaServerEntry 9 }
|
||
|
||
awcAaaServerAdminAuthEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Is this server to be used for AP Admin
|
||
authentication?"
|
||
::= { awcAaaServerEntry 10 }
|
||
|
||
awcAaaServerMipAuthEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Is this server to be used for Proxy Mobile IP
|
||
authentication?"
|
||
::= { awcAaaServerEntry 11 }
|
||
|
||
awcAaaServerMaxRetransmission OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum number of retransmission of a request.
|
||
If an Access Point does not receive a response within
|
||
awcAaaServerTimeout, it retransmits the request. If no
|
||
response is received for a maximum number of
|
||
retransmissions, the server is considered not reachable
|
||
and a secondary server (if any) will be chosen
|
||
temporarily."
|
||
::= { awcAaaServerEntry 12 }
|
||
|
||
|
||
awcAcctServerTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcAcctServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This table provides information of AAA
|
||
accounting servers currently available to
|
||
this access point and the parameters used to
|
||
connect to the servers.
|
||
Each entry corresponds to an AAA server and is
|
||
indexed by the priority in which the server
|
||
should be used. AAA server of lowest priority
|
||
value should be used first. Entries in this
|
||
table cannot be created or deleted by the
|
||
network management system. All entries are
|
||
created or deleted by the agent."
|
||
::= { awcAaa 2 }
|
||
|
||
awcAcctServerEntry OBJECT-TYPE
|
||
SYNTAX AwcAcctServerEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry provide the AAA server usage priority,
|
||
protocol, name, IP port, request timeout, and
|
||
security mechanisms supported."
|
||
INDEX {awcAcctServerPriority}
|
||
::= { awcAcctServerTable 1 }
|
||
|
||
AwcAcctServerEntry ::=
|
||
SEQUENCE {
|
||
awcAcctServerPriority INTEGER,
|
||
awcAcctServerProtocol INTEGER,
|
||
awcAcctServerName DisplayString,
|
||
awcAcctServerPort Unsigned32,
|
||
awcAcctServerTimeout Unsigned32,
|
||
awcAcctServerUpdateEnable TruthValue,
|
||
awcAcctServerUpdateDelay Unsigned32,
|
||
awcAcctClientName DisplayString,
|
||
awcAcctSecureEnabled TruthValue,
|
||
awcAcctGeneralEnabled TruthValue,
|
||
awcAcctServerSharedSecret DisplayString,
|
||
awcAcctServerMaxRetransmission Unsigned32 }
|
||
|
||
awcAcctServerPriority OBJECT-TYPE
|
||
SYNTAX INTEGER (1..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The priority of the server for when multiple servers
|
||
are configured for the same service. Lower priority
|
||
servers are used, in sequence, as backups."
|
||
::= { awcAcctServerEntry 1 }
|
||
|
||
awcAcctServerProtocol OBJECT-TYPE
|
||
SYNTAX INTEGER {radius(1), tacacsPlus(2)}
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The protocol used to communicate with the AAA server."
|
||
::= { awcAcctServerEntry 2 }
|
||
|
||
awcAcctServerName OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The DNS-resolvable name or numeric IP address of the
|
||
AAA server."
|
||
::= { awcAcctServerEntry 3 }
|
||
|
||
awcAcctServerPort OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The IP port number of the AAA server."
|
||
::= { awcAcctServerEntry 4 }
|
||
|
||
awcAcctServerTimeout OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The amount of time (in seconds) that an Access Point
|
||
should wait for a response from the Accounting server
|
||
before retransmitting the request. If the Access Point
|
||
does not receive a response within the timeout
|
||
period, it retransmits the request. If no response is
|
||
received for a maximum of awcAcctServerMaxRetransmission
|
||
retransmissions, the server is considered not reachable
|
||
and a secondary server (if any) will be chosen.
|
||
If the AP and the Accounting server are connected through a
|
||
low-speed network and the awcAcctServerTimeout value is set
|
||
to too low, the network may become congested, as the AP
|
||
retransmits unacknowledged accounting requests that have
|
||
not yet reached the server"
|
||
::= { awcAcctServerEntry 5 }
|
||
|
||
awcAcctServerUpdateEnable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Is the Acct update to this server enabled?."
|
||
::= { awcAcctServerEntry 6 }
|
||
|
||
awcAcctServerUpdateDelay OBJECT-TYPE
|
||
SYNTAX Unsigned32 (60..2592000)
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The amount of time (in seconds) that the Access Point
|
||
should send to the AAA server an update of accounting information."
|
||
::= { awcAcctServerEntry 7 }
|
||
|
||
awcAcctClientName OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The name the Access Point uses to identify itself when
|
||
acting as the supplicant."
|
||
::= { awcAcctServerEntry 8 }
|
||
|
||
awcAcctSecureEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Is this server to be used for accounting with security AUTH?"
|
||
::= { awcAcctServerEntry 9 }
|
||
|
||
awcAcctGeneralEnabled OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Is this server to be used for accounting without security AUTH?"
|
||
::= { awcAcctServerEntry 10 }
|
||
|
||
awcAcctServerSharedSecret OBJECT-TYPE
|
||
SYNTAX DisplayString
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The textual string shared between the ACCT server and
|
||
the access point, used to authenticate the messages
|
||
delivered between them."
|
||
::= { awcAcctServerEntry 11 }
|
||
|
||
awcAcctServerMaxRetransmission OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The maximum number of retransmissions of an accounting
|
||
request. If an Access Point does not receive a response
|
||
within awcAcctServerTimeout, it retransmits the request.
|
||
If no response is received for a maximum number of
|
||
retransmissions, the server is considered not reachable
|
||
and a secondary server (if any) will be chosen."
|
||
::= { awcAcctServerEntry 12 }
|
||
|
||
|
||
awcAcctEnable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The boolean indicating if the accounting is enabled."
|
||
DEFVAL { false }
|
||
::= { awcAcctConfig 1 }
|
||
|
||
awcAcctStopDelayEnable OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The boolean indicating if the accounting stop request
|
||
should be delayed before sent."
|
||
DEFVAL { true }
|
||
::= { awcAcctConfig 2 }
|
||
|
||
awcAcctStopDelayTime OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The duration for the AP to delay sending the STOP message if any."
|
||
DEFVAL { 2 }
|
||
::= { awcAcctConfig 3 }
|
||
|
||
|
||
-- **********************************************************************
|
||
-- * awcAaaAuthConfig parameters - Common to all Authentication servers
|
||
-- **********************************************************************
|
||
|
||
awcAaaAuthConfig OBJECT IDENTIFIER ::= { awcAaa 4 }
|
||
|
||
awcAaaServerPrimaryReattemptPeriod OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"While the primary authentication server serving a given
|
||
authentication function is not reachable, the duration,
|
||
in minutes, at which the AP should reattempt to return
|
||
to its primary server serving that authentication function.
|
||
A value of zero indicates that primary authentication server
|
||
reattempt is disabled."
|
||
::= { awcAaaAuthConfig 1 }
|
||
|
||
awcAaaServerDot1xAuthCurrent OBJECT-TYPE
|
||
SYNTAX INTEGER (0..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The index of the currently selected AAA server for 802.1X user
|
||
authentication. A value of zero indicates that no authentication
|
||
server is available to service 802.1X authentication function to
|
||
this AP. The value of 1 to 4 indicates the corresponding server
|
||
for 802.1X authentication."
|
||
::= { awcAaaAuthConfig 2 }
|
||
|
||
|
||
awcAaaServerMacAddrAuthCurrent OBJECT-TYPE
|
||
SYNTAX INTEGER (0..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The index of the currently selected AAA server for MAC address
|
||
authentication. A value of zero indicates that no authentication
|
||
server is available to service MAC address authentication
|
||
function to this AP. The value of 1 to 4 indicates the
|
||
corresponding server in use for MAC address authentication
|
||
function."
|
||
::= { awcAaaAuthConfig 3 }
|
||
|
||
awcAaaServerAdminAuthCurrent OBJECT-TYPE
|
||
SYNTAX INTEGER (0..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The index of the currently selected AAA server for the Access
|
||
Point administrator authentication function. A value of zero
|
||
indicates that no authentication server is available to service
|
||
admin login authentication function to this AP. The value of 1
|
||
to 4 indicates the corresponding server in use for the AP admin
|
||
authentication function."
|
||
|
||
::= { awcAaaAuthConfig 4 }
|
||
|
||
awcAaaServerMipAuthCurrent OBJECT-TYPE
|
||
SYNTAX INTEGER (0..4)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The index of the currently selected AAA server used to retrieve
|
||
authentication data requied for Proxy Mobile registration and
|
||
authentication function. A value of zero indicates that no
|
||
authentication server is available for this function. The value of 1
|
||
to 4 indicates the corresponding server in use for proxy mobile IP
|
||
related authentication function."
|
||
|
||
::= { awcAaaAuthConfig 5 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcProtocolFilters parameters
|
||
-- ********************************************************************
|
||
|
||
AwcPfDisposition ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designate whether a protocol should be forwarded or blocked,
|
||
or should behave in the default manner of the associated
|
||
network interface."
|
||
SYNTAX INTEGER { forward(1), block(2), default(3) }
|
||
|
||
AwcPfPriority ::= TEXTUAL-CONVENTION
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designate the 802.1P priority with which a protocol should
|
||
be queued."
|
||
SYNTAX INTEGER { default(1), background(2), spare(3),
|
||
excellentEffort(4), controlledLoad(5),
|
||
interactiveVideo(6), interactiveVoice(7),
|
||
networkControl(8) }
|
||
|
||
awcPrFltEthertypeSetTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcPrFltEthertypeSetEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of static Ethertype Filters"
|
||
::= { awcProtocolFilters 1 }
|
||
|
||
awcPrFltEthertypeSetEntry OBJECT-TYPE
|
||
SYNTAX AwcPrFltEthertypeSetEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in awcPrFltEthertypeTable."
|
||
INDEX {awcPfEtSetId}
|
||
::= { awcPrFltEthertypeSetTable 1 }
|
||
|
||
AwcPrFltEthertypeSetEntry ::=
|
||
SEQUENCE {
|
||
awcPfEtSetId Unsigned32,
|
||
awcPfEtSetName DisplayString,
|
||
awcPfEtDefaultDisposition AwcPfDisposition,
|
||
awcPfEtDefaultUcastTimeToLive Unsigned32,
|
||
awcPfEtDefaultNUcastTimeToLive Unsigned32,
|
||
awcPfEtSetStatus RowStatus }
|
||
|
||
awcPfEtSetId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Numeric identifier of the static Ethertype
|
||
filters set."
|
||
::= { awcPrFltEthertypeSetEntry 1 }
|
||
|
||
awcPfEtSetName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..64))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Descriptive name of the static Ethertype
|
||
filters set. Max. string length is 64 octets."
|
||
::= { awcPrFltEthertypeSetEntry 2 }
|
||
|
||
awcPfEtDefaultDisposition OBJECT-TYPE
|
||
SYNTAX AwcPfDisposition
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default packet disposition of the static Ethertype
|
||
filters set."
|
||
DEFVAL { forward }
|
||
::= { awcPrFltEthertypeSetEntry 3 }
|
||
|
||
awcPfEtDefaultUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default time-to-live for unicast (directed) packets.
|
||
A value of 0 means to use the system defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltEthertypeSetEntry 4 }
|
||
|
||
awcPfEtDefaultNUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default time-to-live for non-unicast (multicast)
|
||
packets. A value of 0 means to use the system
|
||
defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltEthertypeSetEntry 5 }
|
||
|
||
awcPfEtSetStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the entire static Ethertype filters
|
||
set."
|
||
::= { awcPrFltEthertypeSetEntry 6 }
|
||
|
||
awcPrFltEthertypeTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcPrFltEthertypeEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of individual static Ethertype filters."
|
||
::= { awcProtocolFilters 2 }
|
||
|
||
awcPrFltEthertypeEntry OBJECT-TYPE
|
||
SYNTAX AwcPrFltEthertypeEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the individual static Ethertype
|
||
filter table."
|
||
INDEX {awcPfEtSetId, awcPfEtEthertype}
|
||
::= { awcPrFltEthertypeTable 1 }
|
||
|
||
AwcPrFltEthertypeEntry ::=
|
||
SEQUENCE {
|
||
awcPfEtEthertype INTEGER,
|
||
awcPfEtDisposition AwcPfDisposition,
|
||
awcPfEtUserPriority AwcPfPriority,
|
||
awcPfEtUcastTimeToLive Unsigned32,
|
||
awcPfEtNUcastTimeToLive Unsigned32,
|
||
awcPfEtAlert TruthValue,
|
||
awcPfEtStatus RowStatus
|
||
}
|
||
|
||
awcPfEtEthertype OBJECT-TYPE
|
||
SYNTAX INTEGER (1..255|1501..65535)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Ethertype (protocol) to which this individual
|
||
static filter applies"
|
||
::= { awcPrFltEthertypeEntry 1 }
|
||
|
||
awcPfEtDisposition OBJECT-TYPE
|
||
SYNTAX AwcPfDisposition
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designation of how the protocol should be
|
||
handled."
|
||
DEFVAL { default }
|
||
::= { awcPrFltEthertypeEntry 2 }
|
||
|
||
awcPfEtUserPriority OBJECT-TYPE
|
||
SYNTAX AwcPfPriority
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designation of the priority assigned to
|
||
packets of the Ethertype."
|
||
DEFVAL { default }
|
||
::= { awcPrFltEthertypeEntry 3 }
|
||
|
||
awcPfEtUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Time-to-live for unicast (directed) packets. A
|
||
value of 0 means to use the Filter Set defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltEthertypeEntry 4 }
|
||
|
||
awcPfEtNUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Time-to-live for non-unicast (multicast) packets. A
|
||
value of 0 means to use the Filter Set defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltEthertypeEntry 5 }
|
||
|
||
awcPfEtAlert OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should an alert be registered when a packet of
|
||
this Ethertype is observed?"
|
||
DEFVAL { false }
|
||
::= { awcPrFltEthertypeEntry 6 }
|
||
|
||
awcPfEtStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the individual static Ethertype
|
||
filters."
|
||
::= { awcPrFltEthertypeEntry 7 }
|
||
|
||
|
||
|
||
awcPrFltIpProtocolSetTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcPrFltIpProtocolSetEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of static IP Protocol Filters"
|
||
::= { awcProtocolFilters 3 }
|
||
|
||
awcPrFltIpProtocolSetEntry OBJECT-TYPE
|
||
SYNTAX AwcPrFltIpProtocolSetEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in awcPrFltIpProtocolTable."
|
||
INDEX {awcPfIppSetId}
|
||
::= { awcPrFltIpProtocolSetTable 1 }
|
||
|
||
AwcPrFltIpProtocolSetEntry ::=
|
||
SEQUENCE {
|
||
awcPfIppSetId Unsigned32,
|
||
awcPfIppSetName DisplayString,
|
||
awcPfIppDefaultDisposition AwcPfDisposition,
|
||
awcPfIppDefaultUcastTimeToLive Unsigned32,
|
||
awcPfIppDefaultNUcastTimeToLive Unsigned32,
|
||
awcPfIppSetStatus RowStatus }
|
||
|
||
awcPfIppSetId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Numeric identifier of the static IP Protocol
|
||
filters set."
|
||
::= { awcPrFltIpProtocolSetEntry 1 }
|
||
|
||
awcPfIppSetName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..64))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Descriptive name of the static IP Protocol
|
||
filters set. Max. string length is 64 octets."
|
||
::= { awcPrFltIpProtocolSetEntry 2 }
|
||
|
||
awcPfIppDefaultDisposition OBJECT-TYPE
|
||
SYNTAX AwcPfDisposition
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default packet disposition of the static IP Protocol
|
||
filters set."
|
||
DEFVAL { forward }
|
||
::= { awcPrFltIpProtocolSetEntry 3 }
|
||
|
||
awcPfIppDefaultUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default time-to-live for unicast (directed) packets.
|
||
A value of 0 means to use the system defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpProtocolSetEntry 4 }
|
||
|
||
awcPfIppDefaultNUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default time-to-live for non-unicast (multicast)
|
||
packets. A value of 0 means to use the system
|
||
defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpProtocolSetEntry 5 }
|
||
|
||
awcPfIppSetStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the entire static IP Protocol filters
|
||
set."
|
||
::= { awcPrFltIpProtocolSetEntry 6 }
|
||
|
||
awcPrFltIpProtocolTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcPrFltIpProtocolEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of individual static IP Protocol
|
||
filters."
|
||
::= { awcProtocolFilters 4 }
|
||
|
||
awcPrFltIpProtocolEntry OBJECT-TYPE
|
||
SYNTAX AwcPrFltIpProtocolEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the individual static IP Protocol
|
||
filter table."
|
||
INDEX {awcPfIppSetId, awcPfIppIpProtocol}
|
||
::= { awcPrFltIpProtocolTable 1 }
|
||
|
||
AwcPrFltIpProtocolEntry ::=
|
||
SEQUENCE {
|
||
awcPfIppIpProtocol INTEGER,
|
||
awcPfIppDisposition AwcPfDisposition,
|
||
awcPfIppUserPriority AwcPfPriority,
|
||
awcPfIppUcastTimeToLive Unsigned32,
|
||
awcPfIppNUcastTimeToLive Unsigned32,
|
||
awcPfIppAlert TruthValue,
|
||
awcPfIppStatus RowStatus
|
||
}
|
||
|
||
awcPfIppIpProtocol OBJECT-TYPE
|
||
SYNTAX INTEGER (0..255)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IP Protocol to which this individual static
|
||
filter applies"
|
||
::= { awcPrFltIpProtocolEntry 1 }
|
||
|
||
awcPfIppDisposition OBJECT-TYPE
|
||
SYNTAX AwcPfDisposition
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designation of how the protocol should be
|
||
handled."
|
||
DEFVAL { default }
|
||
::= { awcPrFltIpProtocolEntry 2 }
|
||
|
||
awcPfIppUserPriority OBJECT-TYPE
|
||
SYNTAX AwcPfPriority
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designation of the priority assigned to
|
||
packets of the IP Protocol."
|
||
DEFVAL { default }
|
||
::= { awcPrFltIpProtocolEntry 3 }
|
||
|
||
awcPfIppUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Time-to-live for unicast (directed) packets. A
|
||
value of 0 means to use the Filter Set defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpProtocolEntry 4 }
|
||
|
||
awcPfIppNUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Time-to-live for non-unicast (multicast) packets. A
|
||
value of 0 means to use the Filter Set defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpProtocolEntry 5 }
|
||
|
||
awcPfIppAlert OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should an alert be registered when a packet
|
||
of this IP Protocol is observed?"
|
||
DEFVAL { false }
|
||
::= { awcPrFltIpProtocolEntry 6 }
|
||
|
||
awcPfIppStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the individual static IP Protocol
|
||
filters."
|
||
::= { awcPrFltIpProtocolEntry 7 }
|
||
|
||
|
||
|
||
awcPrFltIpPortSetTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcPrFltIpPortSetEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of static IP Port Filters"
|
||
::= { awcProtocolFilters 5 }
|
||
|
||
awcPrFltIpPortSetEntry OBJECT-TYPE
|
||
SYNTAX AwcPrFltIpPortSetEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in awcPrFltIpPortTable."
|
||
INDEX {awcPfIptSetId}
|
||
::= { awcPrFltIpPortSetTable 1 }
|
||
|
||
AwcPrFltIpPortSetEntry ::=
|
||
SEQUENCE {
|
||
awcPfIptSetId Unsigned32,
|
||
awcPfIptSetName DisplayString,
|
||
awcPfIptDefaultDisposition AwcPfDisposition,
|
||
awcPfIptDefaultUcastTimeToLive Unsigned32,
|
||
awcPfIptDefaultNUcastTimeToLive Unsigned32,
|
||
awcPfIptSetStatus RowStatus }
|
||
|
||
awcPfIptSetId OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Numeric identifier of the static IP Port
|
||
filters set."
|
||
::= { awcPrFltIpPortSetEntry 1 }
|
||
|
||
awcPfIptSetName OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..64))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Descriptive name of the static IP Port filters
|
||
set. Max. string length is 64 octets."
|
||
::= { awcPrFltIpPortSetEntry 2 }
|
||
|
||
awcPfIptDefaultDisposition OBJECT-TYPE
|
||
SYNTAX AwcPfDisposition
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default packet disposition of the static IP Port
|
||
filters set."
|
||
DEFVAL { forward }
|
||
::= { awcPrFltIpPortSetEntry 3 }
|
||
|
||
awcPfIptDefaultUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default time-to-live for unicast (directed) packets.
|
||
A value of 0 means to use the system defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpPortSetEntry 4 }
|
||
|
||
awcPfIptDefaultNUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Default time-to-live for non-unicast (multicast)
|
||
packets. A value of 0 means to use the system
|
||
defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpPortSetEntry 5 }
|
||
|
||
awcPfIptSetStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the entire static IP Port filters set."
|
||
::= { awcPrFltIpPortSetEntry 6 }
|
||
|
||
awcPrFltIpPortTable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF AwcPrFltIpPortEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Table of individual static IP Port filters."
|
||
::= { awcProtocolFilters 6 }
|
||
|
||
awcPrFltIpPortEntry OBJECT-TYPE
|
||
SYNTAX AwcPrFltIpPortEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry in the individual static IP Port
|
||
filter table."
|
||
INDEX {awcPfIptSetId, awcPfIptIpPort}
|
||
::= { awcPrFltIpPortTable 1 }
|
||
|
||
AwcPrFltIpPortEntry ::=
|
||
SEQUENCE {
|
||
awcPfIptIpPort INTEGER,
|
||
awcPfIptDisposition AwcPfDisposition,
|
||
awcPfIptUserPriority AwcPfPriority,
|
||
awcPfIptUcastTimeToLive Unsigned32,
|
||
awcPfIptNUcastTimeToLive Unsigned32,
|
||
awcPfIptAlert TruthValue,
|
||
awcPfIptStatus RowStatus
|
||
}
|
||
|
||
awcPfIptIpPort OBJECT-TYPE
|
||
SYNTAX INTEGER (1..65535)
|
||
MAX-ACCESS read-only
|
||
STATUS current
|
||
DESCRIPTION
|
||
"IP Port to which this individual static filter
|
||
applies"
|
||
::= { awcPrFltIpPortEntry 1 }
|
||
|
||
awcPfIptDisposition OBJECT-TYPE
|
||
SYNTAX AwcPfDisposition
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designation of how the Port should be
|
||
handled."
|
||
DEFVAL { default }
|
||
::= { awcPrFltIpPortEntry 2 }
|
||
|
||
awcPfIptUserPriority OBJECT-TYPE
|
||
SYNTAX AwcPfPriority
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Designation of the priority assigned to
|
||
packets of the IP Port."
|
||
DEFVAL { default }
|
||
::= { awcPrFltIpPortEntry 3 }
|
||
|
||
awcPfIptUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Time-to-live for unicast (directed) packets. A
|
||
value of 0 means to use the Filter Set defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpPortEntry 4 }
|
||
|
||
awcPfIptNUcastTimeToLive OBJECT-TYPE
|
||
SYNTAX Unsigned32
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Time-to-live for non-unicast (multicast) packets. A
|
||
value of 0 means to use the Filter Set defaults."
|
||
DEFVAL { 0 }
|
||
::= { awcPrFltIpPortEntry 5 }
|
||
|
||
awcPfIptAlert OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Should an alert be registered when a packet of
|
||
this IP Port is observed?"
|
||
DEFVAL { false }
|
||
::= { awcPrFltIpPortEntry 6 }
|
||
|
||
awcPfIptStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the individual static IP Port filters."
|
||
::= { awcPrFltIpPortEntry 7 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcMobileIP parameters
|
||
-- ********************************************************************
|
||
|
||
enableMobileIP OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point's proxy mobile IP
|
||
service is enabled. If false, proxy mobile
|
||
IP service is disabled."
|
||
DEFVAL { true }
|
||
::= { awcMobileIP 1 }
|
||
|
||
awcprimAAP OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The first AAP hostname or IP address from a
|
||
list of 3 AAPs."
|
||
::= { awcMobileIP 2 }
|
||
|
||
awcsec1AAP OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The second AAP hostname or IP address from a
|
||
list of 3 AAPs."
|
||
::= { awcMobileIP 3 }
|
||
|
||
awcsec2AAP OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The third AAP hostname or IP address from a
|
||
list of 3 AAPs."
|
||
::= { awcMobileIP 4 }
|
||
|
||
-- mipSATable
|
||
|
||
mipSATable OBJECT-TYPE
|
||
SYNTAX SEQUENCE OF MipSAEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"This entity's Mobile IP Local SA Bindings table."
|
||
::= { awcMobileIP 5}
|
||
|
||
mipSAEntry OBJECT-TYPE
|
||
SYNTAX MipSAEntry
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"An entry of SA bindings for a range of IP Addresses."
|
||
INDEX { mipSAIpStart }
|
||
::= { mipSATable 1 }
|
||
|
||
MipSAEntry ::= SEQUENCE {
|
||
mipSAIpStart IpAddress,
|
||
mipSAIpEnd IpAddress,
|
||
mipSAGroupSPI DisplayString,
|
||
mipSAGroupKey DisplayString,
|
||
mipSAStatus RowStatus
|
||
}
|
||
|
||
mipSAIpStart OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS not-accessible
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Starting IP Address of a range for the SA binding."
|
||
::= { mipSAEntry 1 }
|
||
|
||
mipSAIpEnd OBJECT-TYPE
|
||
SYNTAX IpAddress
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Ending IP Address of the range for the SA binding."
|
||
::= { mipSAEntry 2 }
|
||
|
||
mipSAGroupSPI OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Group SPI for the range of IP Address in the Local
|
||
SA binding"
|
||
::= { mipSAEntry 3 }
|
||
|
||
mipSAGroupKey OBJECT-TYPE
|
||
SYNTAX DisplayString (SIZE(0..128))
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Group Key for the range of IP Address in the Local
|
||
SA binding"
|
||
::= { mipSAEntry 4 }
|
||
|
||
mipSAStatus OBJECT-TYPE
|
||
SYNTAX RowStatus
|
||
MAX-ACCESS read-create
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Row status of the pMIP SA. Allows deletion via SNMP."
|
||
::= { mipSAEntry 5 }
|
||
|
||
awcmipDebug OBJECT-TYPE
|
||
SYNTAX TruthValue
|
||
MAX-ACCESS read-write
|
||
STATUS current
|
||
DESCRIPTION
|
||
"If true, the Access Point's proxy mobile IP
|
||
debug information is printed on the console.
|
||
If false, debug messages are not printed."
|
||
DEFVAL { true }
|
||
::= { awcMobileIP 6 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * awcEventLog Traps
|
||
-- ********************************************************************
|
||
|
||
awcTrapLog NOTIFICATION-TYPE
|
||
OBJECTS { awcEventTime, awcEventSeverity, awcEventDescription,
|
||
awcEventType }
|
||
STATUS current
|
||
DESCRIPTION
|
||
"SNMP trap corresponding to an event with a Severity
|
||
Level requiring Notify Disposition while
|
||
awcEventAlertSNMP is true."
|
||
::= { aironet 4 }
|
||
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcEventLog parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * awcExperimental parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcExperimental parameters
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * Conformance information
|
||
-- ********************************************************************
|
||
|
||
awcVxConformance
|
||
OBJECT IDENTIFIER ::= { awcVx 100 }
|
||
awcVxCompliances
|
||
OBJECT IDENTIFIER ::= { awcVxConformance 1 }
|
||
awcVxGroups
|
||
OBJECT IDENTIFIER ::= { awcVxConformance 2 }
|
||
|
||
|
||
-- ********************************************************************
|
||
-- * Compliance statements
|
||
-- ********************************************************************
|
||
|
||
awcVxCompliance MODULE-COMPLIANCE
|
||
STATUS current
|
||
DESCRIPTION
|
||
"The compliance statement for the awcVx group."
|
||
MODULE -- this module
|
||
MANDATORY-GROUPS {
|
||
awcSystemGroup,
|
||
bootconfigVxGroup,
|
||
awcSerialDevGroup,
|
||
awcFtpGroup,
|
||
awcIfTableGroup,
|
||
awc802dot11Group,
|
||
awcUserMgrGroup,
|
||
awcHttpdGroup,
|
||
awcDnsResGroup,
|
||
awcSnmpGroup,
|
||
awcSntpGroup,
|
||
awcForwardTblGroup,
|
||
-- awcRipConfigGroup,
|
||
awcEventLogGroup,
|
||
awcEtherMIBGroup,
|
||
awcDdpIAPPGroup,
|
||
awcHotStandbyGroup,
|
||
awcAaaGroup,
|
||
awcProtocolFiltersGroup,
|
||
awcMobileIpGroup
|
||
}
|
||
|
||
::= { awcVxCompliances 1 }
|
||
|
||
-- ********************************************************************
|
||
-- * Units of conformance
|
||
-- ********************************************************************
|
||
|
||
awcSystemGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
vxWorksVersion,
|
||
creationDate,
|
||
awcVxVersion,
|
||
sysFlags,
|
||
languageCode,
|
||
awcDevID,
|
||
awcDevIDtxt,
|
||
enableHTTP,
|
||
enableTelnet,
|
||
enableSNMP,
|
||
enableDnsResolver,
|
||
enableSNTP,
|
||
enableWDB,
|
||
pingTxLen,
|
||
awcFirstBoot,
|
||
awcOemOUI,
|
||
awcOemName,
|
||
awcOemNameShort,
|
||
awcOemHomeURL,
|
||
enablePSPF,
|
||
sysExceptionReboot,
|
||
bootblockVersion,
|
||
motherboardRevision,
|
||
enableSTP,
|
||
enableRebootKey,
|
||
awcLocateUnit
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support operation of an Aironet Access
|
||
Point such as versions, system flags, and what features are
|
||
enabled."
|
||
::= { awcVxGroups 1 }
|
||
|
||
bootconfigVxGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
bootconfigBootProtocol,
|
||
bootconfigReadINI,
|
||
bootconfigServerConfigTimeout,
|
||
bootconfigMultOfferTimeout,
|
||
bootconfigReqLeaseDuration,
|
||
bootconfigMinLeaseDuration,
|
||
bootconfigDev,
|
||
bootconfigClientAddr,
|
||
bootconfigHostAddr,
|
||
bootconfigBootFile,
|
||
bootconfigSubnetMask,
|
||
bootconfigGateway,
|
||
bootconfigHostName,
|
||
bootconfigClientName,
|
||
bootconfigNameServerPriority,
|
||
bootconfigNameServer,
|
||
bootconfigDomainName,
|
||
bootconfigSntpServer,
|
||
bootconfigSaveServerResponse,
|
||
bootconfigCmdInvokeIniLoad,
|
||
bootconfigCmdStatusIniLoad,
|
||
bootconfigDhcpClassID,
|
||
bootconfigFileServerAddr,
|
||
bootconfigLogServerAddr,
|
||
bootconfigBootCount,
|
||
bootconfigDhcpClientIdType,
|
||
bootconfigDhcpClientIdValue
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support operation of the boot server."
|
||
::= { awcVxGroups 2 }
|
||
|
||
awcSerialDevGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
serialDevIndex,
|
||
serialAdminStatus,
|
||
serialOperStatus,
|
||
serialBaud,
|
||
serialParity,
|
||
serialDataBits,
|
||
serialStopBits,
|
||
serialFlowControl,
|
||
serialTerminalType,
|
||
serialTerminalLines,
|
||
serialTerminalColumns,
|
||
serialDevFd
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of serial ports."
|
||
::= { awcVxGroups 3 }
|
||
|
||
awcFtpGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
defaultFileServer,
|
||
awcFileXferProtocol,
|
||
awcFileXferUser,
|
||
awcFileXferPassword,
|
||
awcFileXferCmdInvokeFileLoad,
|
||
awcFileXferCmdStatusFileLoad,
|
||
awcFileXferCmdInvokeFileSave,
|
||
awcFileXferCmdStatusFileSave,
|
||
awcFileXferFileFirmwareSystem,
|
||
awcFileXferFileFirmwareRadio0,
|
||
awcFileXferFileWebUI,
|
||
awcFileXferFileFpgaPcmcia,
|
||
awcFileXferTftpPort,
|
||
awcFileXferFtpDirectory,
|
||
awcFileXferFilesFLASH,
|
||
awcFileXferFileFirmwareRadio1
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the FTP
|
||
protocol."
|
||
::= { awcVxGroups 4 }
|
||
|
||
awcIfTableGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcIfDefaultPhysAddress,
|
||
awcIfPhysAddress,
|
||
awcIfAdoptPrimaryIdentity,
|
||
awcIfDefaultIpAddress,
|
||
awcIfDefaultIpNetMask,
|
||
awcIfIpAddress,
|
||
awcIfIpNetMask,
|
||
awcIfMSDUMaxLength,
|
||
awcIfOutDiscardsCoS0,
|
||
awcIfOutDiscardsCoS1,
|
||
awcIfOutDiscardsCoS2,
|
||
awcIfOutDiscardsCoS3,
|
||
awcIfOutDiscardsCoS4,
|
||
awcIfOutDiscardsCoS5,
|
||
awcIfOutDiscardsCoS6,
|
||
awcIfOutDiscardsCoS7
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of network
|
||
interfaces."
|
||
::= { awcVxGroups 5 }
|
||
|
||
awc802dot11Group OBJECT-GROUP
|
||
OBJECTS {
|
||
awcDot11StationRole,
|
||
awcDot11PowerManagementSubMode,
|
||
awcDot11UseAWCExtensions,
|
||
awcDot11AllowAssocBroadcastSSID,
|
||
awcDot11PrivacyOptionImplementedMaxRate,
|
||
awcDot11DesiredBSSLength,
|
||
awcDot11EnetEncapsulationDefault,
|
||
awcDot11ForceReqFirmwareVersion,
|
||
awcDot11BridgeSpacing,
|
||
awcDot11DesiredSSIDMaxAssociatedSTA,
|
||
awcDot11DesiredSSIDNumAssociatedSTA,
|
||
awcDot11AuxiliarySSIDLength,
|
||
awcDot11MultipleSSIDPerBSSImplemented,
|
||
awcDot11SymbolExtensionsImplemented,
|
||
awcDot11SymbolExtensionsEnabled,
|
||
awcDot11DesiredSSIDMicAlgorithm,
|
||
awcDot11DesiredSSIDWEPKeyPermuteAlgorithm,
|
||
awcDot11DesiredSSIDInfrastructureWGB,
|
||
awcDot11DesiredSSIDDefaultPolId,
|
||
awcDot11DesiredSSIDDefaultVlanId,
|
||
awcDot11DesiredSSIDEnableProxyMobileIP,
|
||
awcDot11InfrastructureSSID,
|
||
awcDot11QBSSElementImplemented,
|
||
awcDot11QBSSElementEnabled,
|
||
awcDot11InfrastructureSSIDExclusive,
|
||
awcDot11SendIGMPGeneralQuery,
|
||
awcDot11AuthenticationRequireEAP,
|
||
awcDot11AuthenticationDefaultUcastAllowedToGoTo,
|
||
awcDot11WEPDefaultKeyIndex,
|
||
awcDot11WEPDefaultKeyLen,
|
||
awcDot11WEPDefaultKeyValue,
|
||
awcDot11WEPDefaultKeyMaxIndex,
|
||
awcDot11AllowEncrypted,
|
||
awcDot11WEPKeyMaxLen,
|
||
awcDot11LEAPUserName,
|
||
awcDot11LEAPPassword,
|
||
awcDot11DesiredBSSIndex,
|
||
awcDot11DesiredBSS,
|
||
awcDot11AuxSSIDIndex,
|
||
awcDot11AuxSSID,
|
||
awcDot11AuxSSIDMaxAssociatedSTA,
|
||
awcDot11AuxSSIDNumAssociatedSTA,
|
||
awcDot11AuxSSIDDefaultPolId,
|
||
awcDot11AuxSSIDDefaultVlanId,
|
||
awcDot11AuxSSIDEnableProxyMobileIP,
|
||
awcDot11AuxSSIDAuthAlgEnable,
|
||
awcDot11AuxSSIDAuthAlgRequireEAP,
|
||
awcDot11AuxSSIDAuthAlgDefaultUcastAllowedToGoTo,
|
||
awcDot11AssignedAID,
|
||
awcDot11AssignedSTA,
|
||
awcDot11FirmwareBootstrapVersion,
|
||
awcDot11CurrentCarrierSet,
|
||
awcDot11ModulationType,
|
||
awcDot11PreambleType,
|
||
awcDot11PHYType,
|
||
awcDot11Compatible3100,
|
||
awcDot11Compatible4500,
|
||
awcDot11ChannelAutoImplemented,
|
||
awcDot11ChannelAutoEnabled,
|
||
awcDot11CurrentChannel,
|
||
awcDot11SupportedDataRatesPrivacyIndex,
|
||
awcDot11SupportedDataRatesPrivacyValue,
|
||
awcDot11SupportedDataRatesPrivacyImplemented,
|
||
awcDot11ChanSelectChannel,
|
||
awcDot11ChanSelectEnable,
|
||
awcDot11AssociatedStationCount,
|
||
awcDot11AuthenticatedStationCount,
|
||
awcDot11ReassociatedStationCount,
|
||
awcDot11RoamedStationCount,
|
||
awcDot11DeauthenticateCount,
|
||
awcDot11DisassociateCount,
|
||
awcDot11EncapPktsMMH,
|
||
awcDot11DecapPktsMMH,
|
||
awcDot11EncapErrorsMMH,
|
||
awcDot11DecapErrorsMMH,
|
||
awcDot11DecapExistsMMH,
|
||
awcDot11DecapAccessMMH,
|
||
awcDot11TxDeferEnergyCount,
|
||
awcDot11RxMacCrcErrorCount,
|
||
awcDot11SsidMismatchCount,
|
||
awcDot11QoSCWmin,
|
||
awcDot11QoSCWmax
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the 802.11
|
||
protocol."
|
||
::= { awcVxGroups 6 }
|
||
|
||
awcUserMgrGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
userMgrUserIndex,
|
||
userMgrUserName,
|
||
userMgrPassword,
|
||
userMgrCapabilities,
|
||
userMgrStatus,
|
||
enableUserMgr,
|
||
allowBrowseWithoutLogin,
|
||
protectLegalPage
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the User
|
||
Manager."
|
||
::= { awcVxGroups 7 }
|
||
|
||
awcHttpdGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
defaultWebRoot,
|
||
defaultHelpRoot,
|
||
getWebUI,
|
||
cmdInvokeGetWebUI,
|
||
cmdStatusGetWebUI,
|
||
awcHttpdPort,
|
||
awcConsoleAutoApply
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the Web
|
||
Server."
|
||
::= { awcVxGroups 8 }
|
||
|
||
awcDnsResGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
resolverDomain,
|
||
resolverDomainSuffix,
|
||
resolverDomainServerPriority,
|
||
resolverDomainServer,
|
||
defaultResolverDomain,
|
||
defaultResolverDomainServerPriority,
|
||
defaultResolverDomainServer
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the DNS
|
||
Resolver."
|
||
::= { awcVxGroups 9 }
|
||
|
||
awcSnmpGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
snmpTrapDest,
|
||
snmpTrapCommunity
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the SNMP
|
||
protocol."
|
||
::= { awcVxGroups 10 }
|
||
|
||
awcSntpGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
defaultSntpServer,
|
||
sntpServer
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the SNTP
|
||
protocol."
|
||
::= { awcVxGroups 11 }
|
||
|
||
awcForwardTblGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcFtMcastAddr,
|
||
awcFtDsHost,
|
||
awcFtBridgeHost,
|
||
awcFtClientSTA,
|
||
awcFtClientSTASelf,
|
||
awcFtBridge,
|
||
awcFtBridgeSelf,
|
||
awcFtRepeater,
|
||
awcFtRepeaterSelf,
|
||
awcFtAccessPoint,
|
||
awcFtBridgeRoot,
|
||
awcFtMaxNumEntries,
|
||
awcFtTimeoutSecUnknown,
|
||
awcFtTimeoutSecMcastAddr,
|
||
awcFtTimeoutSecDsHost,
|
||
awcFtTimeoutSecBridgeHost,
|
||
awcFtTimeoutSecClientSTA,
|
||
awcFtTimeoutSecBridge,
|
||
awcFtTimeoutSecRepeater,
|
||
awcFtTimeoutSecAccessPoint,
|
||
awcFtTimeoutSecBridgeRoot,
|
||
awcFtEnableAwcTpFdbTable,
|
||
awcFtEnableMacAuthServer,
|
||
awcFtRogueApAlertTimeout,
|
||
awcFtEnableMacOrEapAuth,
|
||
awcFtDot1dTpFdbTableEnable,
|
||
awcTpFdbAddress,
|
||
awcTpFdbClassID,
|
||
awcTpFdbSrcPktsImmed,
|
||
awcTpFdbSrcOctetsImmed,
|
||
awcTpFdbSrcErrorPktsImmed,
|
||
awcTpFdbSrcErrorOctetsImmed,
|
||
awcTpFdbDestPktsImmed,
|
||
awcTpFdbDestOctetsImmed,
|
||
awcTpFdbDestErrorPktsImmed,
|
||
awcTpFdbDestErrorOctetsImmed,
|
||
awcTpFdbDestMaxRetryErrorsImmed,
|
||
awcTpFdbIPv4Addr,
|
||
awcTpFdbDdpAddress,
|
||
awcTpFdbDdpSysName,
|
||
awcTpFdbDdpProdDevID,
|
||
awcTpFdbDdpRadioDevID,
|
||
awcTpFdbDdpSwVerMajor,
|
||
awcTpFdbDdpSwVerMinor,
|
||
awcTpFdbDdpSwVerBeta,
|
||
awcTpFdbDdpUptime,
|
||
awcTpFdbDdpNumAnnounceSent,
|
||
awcTpFdbDdpNumAssociated,
|
||
awcTpFdbDdpLoad,
|
||
awcTpFdbDdpDistFromDS,
|
||
awcDot11TpFdbAddress,
|
||
awcDot11TpFdbAID,
|
||
awcDot11TpFdbClientState,
|
||
awcDot11TpFdbTxShortRetries,
|
||
awcDot11TpFdbTxLongRetries,
|
||
awcDot11TpFdbLatestTxShortRetries,
|
||
awcDot11TpFdbLatestTxLongRetries,
|
||
awcDot11TpFdbRxWEPErrors,
|
||
awcDot11TpFdbLatestRxSignalStrength,
|
||
awcDot11TpFdbLatestRxSignalQuality,
|
||
awcDot11TpFdbCapabilities,
|
||
awcDot11TpFdbListenInterval,
|
||
awcDot11TpFdbSupportedDataRates,
|
||
awcDot11TpFdbPreferredTxRate,
|
||
awcDot11TpFdbCurrentBSS,
|
||
awcDot11TpFdbSSID,
|
||
awcDot11TpFdbVlanId,
|
||
awcDot1dTpPortDefaultUcastAllowedToGoTo,
|
||
awcDot1dTpPortDefaultNUcastAllowedToGoTo,
|
||
awcDot1dTpPortMaxNUcastPerSecond,
|
||
awcDot1dTpPortDefaultInEthertypeFilterId,
|
||
awcDot1dTpPortDefaultOutEthertypeFilterId,
|
||
awcDot1dTpPortDefaultInIpProtoFilterId,
|
||
awcDot1dTpPortDefaultOutIpProtoFilterId,
|
||
awcDot1dTpPortDefaultInIpPortFilterId,
|
||
awcDot1dTpPortDefaultOutIpPortFilterId,
|
||
awcTpFdbAlertAddress,
|
||
awcTpFdbFromAlertSrcPktsImmed,
|
||
awcTpFdbFromAlertSrcOctetsImmed,
|
||
awcTpFdbToAlertDestPktsImmed,
|
||
awcTpFdbToAlertDestOctetsImmed,
|
||
awcTpFdbAlertSentAlertTypePktsImmed,
|
||
awcTpFdbAlertSentAlertTypeOctetsImmed,
|
||
awcTpFdbAlertRcvdAlertTypePktsImmed,
|
||
awcTpFdbAlertRcvdAlertTypeOctetsImmed
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of the Forwarding
|
||
Table."
|
||
::= { awcVxGroups 12 }
|
||
|
||
-- awcRipConfigGroup OBJECT-GROUP
|
||
-- OBJECTS {
|
||
-- }
|
||
-- STATUS current
|
||
-- DESCRIPTION
|
||
-- "Standard information to support configuration of the RIP
|
||
-- Protocol."
|
||
-- ::= { awcVxGroups 13 }
|
||
|
||
awcEventLogGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcEventOffsetGMT,
|
||
awcEventUseDaylightSavingsTime,
|
||
awcEventTimestampGMT,
|
||
awcEventUptimeModifiedGMT,
|
||
awcEventDisplayWallClockTime,
|
||
awcEventDisplayUptimeAscending,
|
||
awcEventDetailDefault,
|
||
awcEventSeverityDispConsole,
|
||
awcEventSeverityDispHtmlGUI,
|
||
awcEventSeverityDispHtmlConsole,
|
||
awcEventAlertSNMP,
|
||
awcEventAlertSyslog,
|
||
awcEventCntSeverityNULL,
|
||
awcEventCntSeveritySilent,
|
||
awcEventCntSeveritySystemFatal,
|
||
awcEventCntSeverityProtocolFatal,
|
||
awcEventCntSeverityPortFatal,
|
||
awcEventCntSeveritySystemAlert,
|
||
awcEventCntSeverityProtocolAlert,
|
||
awcEventCntSeverityPortAlert,
|
||
awcEventCntSeverityExternalAlert,
|
||
awcEventCntSeveritySystemWarning,
|
||
awcEventCntSeverityProtocolWarning,
|
||
awcEventCntSeverityPortWarning,
|
||
awcEventCntSeverityExternalWarning,
|
||
awcEventCntSeveritySystemInfo,
|
||
awcEventCntSeverityProtocolInfo,
|
||
awcEventCntSeverityPortInfo,
|
||
awcEventCntSeverityExternalInfo,
|
||
awcEventDispSeverityNULL,
|
||
awcEventDispSeveritySilent,
|
||
awcEventDispSeveritySystemFatal,
|
||
awcEventDispSeverityProtocolFatal,
|
||
awcEventDispSeverityPortFatal,
|
||
awcEventDispSeveritySystemAlert,
|
||
awcEventDispSeverityProtocolAlert,
|
||
awcEventDispSeverityPortAlert,
|
||
awcEventDispSeverityExternalAlert,
|
||
awcEventDispSeveritySystemWarning,
|
||
awcEventDispSeverityProtocolWarning,
|
||
awcEventDispSeverityPortWarning,
|
||
awcEventDispSeverityExternalWarning,
|
||
awcEventDispSeveritySystemInfo,
|
||
awcEventDispSeverityProtocolInfo,
|
||
awcEventDispSeverityPortInfo,
|
||
awcEventDispSeverityExternalInfo,
|
||
awcEventSyslogAddr,
|
||
awcEventSyslogFacility,
|
||
awcEventTraceStationSeverity,
|
||
awcEventTraceLogSize,
|
||
awcEventTracePacketLen,
|
||
awcEventID,
|
||
awcEventTime,
|
||
awcEventSeverity,
|
||
awcEventDescription,
|
||
awcEventType,
|
||
awcEventUseCiscoFormat,
|
||
awcDot11AuthenticateFailDisposition,
|
||
awcDot11DeauthenticateDisposition,
|
||
awcDot11DisassociateDisposition
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support operation of the Event Log."
|
||
::= { awcVxGroups 14 }
|
||
|
||
awcEtherMIBGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcEtherIfSpeedSelect,
|
||
awcEtherDuplex,
|
||
awcEtherCamSize,
|
||
awcEtherEnableSwCam,
|
||
awcEtherForcePortUnblock
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support operation of the Ethernet
|
||
Controller."
|
||
::= { awcVxGroups 15 }
|
||
|
||
awcPolicyGroupsGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcPolGrpName,
|
||
awcPolGrpStatus,
|
||
awcPolGrpInEthertypeFilterId,
|
||
awcPolGrpOutEthertypeFilterId,
|
||
awcPolGrpInIpProtoFilterId,
|
||
awcPolGrpOutIpProtoFilterId,
|
||
awcPolGrpInIpPortFilterId,
|
||
awcPolGrpOutIpPortFilterId,
|
||
awcDscpToCosMapEnable,
|
||
-- awcDscpToCosMapDscp,
|
||
awcDscpToCosMapCos
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support operation of Policy Groups."
|
||
::= { awcVxGroups 16 }
|
||
|
||
awcDdpIAPPGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcIappMcastIpAddr,
|
||
awcIappPort,
|
||
awcP802dot1XVersion
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support operation of the DDP and IAPP
|
||
protocols."
|
||
::= { awcVxGroups 17 }
|
||
|
||
awcHotStandbyGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcHotStandbyMACAddr,
|
||
awcHotStandbyPollingFrequency,
|
||
awcHotStandbyPollingTimeOut,
|
||
awcHotStandbyInHotStandby,
|
||
awcHotStandbyState,
|
||
awcHotStandbyStatus
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support operation of an AP in the
|
||
Hot Standby mode."
|
||
::= { awcVxGroups 18 }
|
||
|
||
awcAaaGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcAaaServerPriority,
|
||
awcAaaServerProtocol,
|
||
awcAaaServerName,
|
||
awcAaaServerPort,
|
||
awcAaaServerTimeout,
|
||
awcAaaClientName,
|
||
awcAaaServerSharedSecret,
|
||
awcAaaServer8021xCapabilityEnabled,
|
||
awcAaaServerMacAddrAuthEnabled,
|
||
awcAaaServerAdminAuthEnabled,
|
||
awcAaaServerMipAuthEnabled,
|
||
awcAaaServerMaxRetransmission,
|
||
awcAcctServerPriority,
|
||
awcAcctServerProtocol,
|
||
awcAcctServerName,
|
||
awcAcctServerPort,
|
||
awcAcctServerTimeout,
|
||
awcAcctServerUpdateEnable,
|
||
awcAcctServerUpdateDelay,
|
||
awcAcctClientName,
|
||
awcAcctSecureEnabled,
|
||
awcAcctGeneralEnabled,
|
||
awcAcctServerSharedSecret,
|
||
awcAcctServerMaxRetransmission,
|
||
awcAcctEnable,
|
||
awcAcctStopDelayEnable,
|
||
awcAcctStopDelayTime,
|
||
awcAaaServerPrimaryReattemptPeriod,
|
||
awcAaaServerDot1xAuthCurrent,
|
||
awcAaaServerMacAddrAuthCurrent,
|
||
awcAaaServerAdminAuthCurrent,
|
||
awcAaaServerMipAuthCurrent
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of RADIUS
|
||
and TACACS+ client operation."
|
||
::= { awcVxGroups 19 }
|
||
|
||
awcProtocolFiltersGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcPfEtSetId,
|
||
awcPfEtSetName,
|
||
awcPfEtDefaultDisposition,
|
||
awcPfEtDefaultUcastTimeToLive,
|
||
awcPfEtDefaultNUcastTimeToLive,
|
||
awcPfEtSetStatus,
|
||
awcPfEtEthertype,
|
||
awcPfEtDisposition,
|
||
awcPfEtUserPriority,
|
||
awcPfEtUcastTimeToLive,
|
||
awcPfEtNUcastTimeToLive,
|
||
awcPfEtAlert,
|
||
awcPfEtStatus,
|
||
awcPfIppSetId,
|
||
awcPfIppSetName,
|
||
awcPfIppDefaultDisposition,
|
||
awcPfIppDefaultUcastTimeToLive,
|
||
awcPfIppDefaultNUcastTimeToLive,
|
||
awcPfIppSetStatus,
|
||
awcPfIppIpProtocol,
|
||
awcPfIppDisposition,
|
||
awcPfIppUserPriority,
|
||
awcPfIppUcastTimeToLive,
|
||
awcPfIppNUcastTimeToLive,
|
||
awcPfIppAlert,
|
||
awcPfIppStatus,
|
||
awcPfIptSetId,
|
||
awcPfIptSetName,
|
||
awcPfIptDefaultDisposition,
|
||
awcPfIptDefaultUcastTimeToLive,
|
||
awcPfIptDefaultNUcastTimeToLive,
|
||
awcPfIptSetStatus,
|
||
awcPfIptIpPort,
|
||
awcPfIptDisposition,
|
||
awcPfIptUserPriority,
|
||
awcPfIptUcastTimeToLive,
|
||
awcPfIptNUcastTimeToLive,
|
||
awcPfIptAlert,
|
||
awcPfIptStatus
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Standard information to support configuration of static protocol
|
||
filters on the AP."
|
||
::= { awcVxGroups 20 }
|
||
|
||
awcMobileIpGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
enableMobileIP,
|
||
mipSAIpEnd,
|
||
mipSAGroupSPI,
|
||
mipSAGroupKey,
|
||
mipSAStatus,
|
||
awcmipDebug,
|
||
awcprimAAP,
|
||
awcsec1AAP,
|
||
awcsec2AAP
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Information to support configuration of proxy mobile IP on the AP."
|
||
::= { awcVxGroups 21 }
|
||
|
||
awcEthernetLostGroup OBJECT-GROUP
|
||
OBJECTS {
|
||
awcEtherLostEthernetSeconds,
|
||
awcEtherLostEthernetAction,
|
||
awcEtherLostEthernetSSID
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Information to support AP in case Ethernet connection is lost."
|
||
::= { awcVxGroups 22 }
|
||
|
||
awc802dot11GroupExt1 OBJECT-GROUP
|
||
OBJECTS {
|
||
awcDot11NonRootMobility
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Configuration information for IEEE 802.11 radio driver
|
||
and firmware."
|
||
::= { awcVxGroups 23 }
|
||
|
||
awcForwardTblGroupExt1 OBJECT-GROUP
|
||
OBJECTS {
|
||
awcFtEnableMcastMapping
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"Information to support configuration of the Forwarding
|
||
Table."
|
||
::= { awcVxGroups 24 }
|
||
|
||
awcTrapLogGroup NOTIFICATION-GROUP
|
||
NOTIFICATIONS { awcTrapLog
|
||
}
|
||
STATUS current
|
||
DESCRIPTION
|
||
"SNMP trap corresponding to an event with a Severity Level
|
||
requiring Notify Disposition while awcEventAlertSNMP is
|
||
true."
|
||
::= { awcVxGroups 100 }
|
||
|
||
-- ********************************************************************
|
||
-- * End of units of conformance
|
||
-- ********************************************************************
|
||
|
||
-- ********************************************************************
|
||
-- * End of awcVx MIB
|
||
-- ********************************************************************
|
||
END
|
||
|
||
|