736 lines
26 KiB
Plaintext
736 lines
26 KiB
Plaintext
--**************************************************************************
|
|
--
|
|
-- Copyright 2007 Broadcom Corporation
|
|
-- All Rights Reserved
|
|
-- No portions of this material may be reproduced in any form without the
|
|
-- written permission of:
|
|
-- Broadcom Corporation
|
|
-- 16251 Laguna Canyon Road
|
|
-- Irvine, California 92618
|
|
-- All information contained in this document is Broadcom Corporation
|
|
-- company private, proprietary, and trade secret.
|
|
--
|
|
--
|
|
--
|
|
--**************************************************************************
|
|
-- Filename: brcm-v2-factory.mib
|
|
-- Author: Kevin O'Neal
|
|
-- Creation Date: 12-september-2002
|
|
--
|
|
--**************************************************************************
|
|
-- Description:
|
|
--
|
|
-- private MIB for V2 factory. Contains objects that are
|
|
-- specific to V2 code structure rather than being more
|
|
-- generic for any old device.
|
|
--
|
|
--**************************************************************************
|
|
-- Revision History:
|
|
--
|
|
--**************************************************************************
|
|
|
|
BRCM-V2-FACTORY-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY,
|
|
OBJECT-TYPE,
|
|
Integer32,
|
|
Unsigned32,
|
|
IpAddress
|
|
FROM SNMPv2-SMI
|
|
SnmpAdminString
|
|
FROM SNMP-FRAMEWORK-MIB
|
|
TruthValue,
|
|
DisplayString,
|
|
DateAndTime
|
|
FROM SNMPv2-TC
|
|
cableDataFactory
|
|
FROM BRCM-CABLEDATA-FACTORY-MIB;
|
|
|
|
v2Factory MODULE-IDENTITY
|
|
LAST-UPDATED "200702050000Z"
|
|
ORGANIZATION "Broadcom Corporation"
|
|
CONTACT-INFO
|
|
" BANANA-CABLEDATA
|
|
(cableData branch of the
|
|
Broadcom Assigned Numbers and Naming Authority)
|
|
Broadcom Corporation
|
|
|
|
Postal: 4385 River Green Parkway
|
|
Duluth, GA 30096
|
|
USA
|
|
|
|
Tel: +1 770 232-0018
|
|
|
|
E-mail: banana-cabledata@broadcom.com"
|
|
DESCRIPTION
|
|
"Broadcom proprietary MIB for factory management and configuration
|
|
of objects common to the V2 software architecture."
|
|
REVISION "200702050000Z"
|
|
DESCRIPTION
|
|
"Module description was updated.
|
|
Compilability issues were cleaned up:
|
|
- Chronological order of revision history was corrected.
|
|
- Range restriction was added to objects v2NonVolIndex and v2FwIndex."
|
|
REVISION "200404090000Z"
|
|
DESCRIPTION
|
|
"Added objects v2NonVolIsManufacturedPermanent,
|
|
v2NonVolMfgHintPermanent, v2NonVolIsManufacturedDynamic, and
|
|
v2NonVolMfgHintDynamic."
|
|
REVISION "200307110000Z"
|
|
DESCRIPTION
|
|
"Eliminate 1024 byte size limit on v2NonVolRawData."
|
|
REVISION "200304160000Z"
|
|
DESCRIPTION
|
|
"Added cmpLZMA to enumerated BITS list for
|
|
v2BootloaderCompressionSupport and v2FwControl objects."
|
|
REVISION "200209120000Z"
|
|
DESCRIPTION
|
|
"Initial version of this MIB module."
|
|
::= { cableDataFactory 4 }
|
|
|
|
-- v2FactoryNonVol: objects to control V2 specific non-vol storage
|
|
v2FactoryNonVol OBJECT IDENTIFIER ::= { v2Factory 1 }
|
|
|
|
v2FactNonVolTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF V2FactNonVolEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A list of V2 style non-volatile storage groups for this device."
|
|
::= { v2FactoryNonVol 1 }
|
|
|
|
v2FactNonVolEntry OBJECT-TYPE
|
|
SYNTAX V2FactNonVolEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry defining a single V2 style non-volatile storage group."
|
|
INDEX { v2NonVolIndex }
|
|
::= { v2FactNonVolTable 1 }
|
|
|
|
V2FactNonVolEntry ::=
|
|
SEQUENCE {
|
|
v2NonVolIndex Integer32,
|
|
v2NonVolName DisplayString,
|
|
v2NonVolMagicNumber OCTET STRING,
|
|
v2NonVolVersionPermanent DisplayString,
|
|
v2NonVolVersionDynamic DisplayString,
|
|
v2NonVolIsDefaultPermanent TruthValue,
|
|
v2NonVolIsDefaultDynamic TruthValue,
|
|
v2NonVolRawData OCTET STRING,
|
|
v2NonVolIsManufacturedPermanent TruthValue,
|
|
v2NonVolMfgHintPermanent DisplayString,
|
|
v2NonVolIsManufacturedDynamic TruthValue,
|
|
v2NonVolMfgHintDynamic DisplayString
|
|
}
|
|
|
|
v2NonVolIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..4096)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the instance number of this entry."
|
|
::= { v2FactNonVolEntry 1 }
|
|
|
|
v2NonVolName OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The name of this non-volatile storage group."
|
|
::= { v2FactNonVolEntry 2 }
|
|
|
|
v2NonVolMagicNumber OBJECT-TYPE
|
|
SYNTAX OCTET STRING (SIZE (4))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A unique four-byte identifier of this non-volatile storage group."
|
|
::= { v2FactNonVolEntry 3 }
|
|
|
|
v2NonVolVersionPermanent OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the major and minor version of the permanent section of
|
|
this non-volatile storage group in the form major.minor"
|
|
::= { v2FactNonVolEntry 4 }
|
|
|
|
v2NonVolVersionDynamic OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the major and minor version of the dynamic section of
|
|
this non-volatile storage group in the form major.minor"
|
|
::= { v2FactNonVolEntry 5 }
|
|
|
|
v2NonVolIsDefaultPermanent OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Reports whether the permanent section of this non-volatile storage
|
|
group has been modified from its default state."
|
|
::= { v2FactNonVolEntry 6 }
|
|
|
|
v2NonVolIsDefaultDynamic OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Reports whether the dynamic section of this non-volatile storage
|
|
group has been modified from its default state."
|
|
::= { v2FactNonVolEntry 7 }
|
|
|
|
v2NonVolRawData OBJECT-TYPE
|
|
SYNTAX OCTET STRING
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The contents of this non-volatile storage group expressed as raw
|
|
binary data."
|
|
::= { v2FactNonVolEntry 8 }
|
|
|
|
v2NonVolIsManufacturedPermanent OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Reports whether the permanent section of this non-volatile storage
|
|
group has been sufficiently manufactured. Criteria for manufacturing
|
|
are of course specific to a given group. Software implementations may
|
|
take some kind of action to limit private MIB access once all nonvol
|
|
groups report that they are manufactured."
|
|
::= { v2FactNonVolEntry 9 }
|
|
|
|
v2NonVolMfgHintPermanent OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If v2NonVolIsManufacturedPermanent is false(2), this object reports
|
|
a textual hint as to which settings in the group have not yet been
|
|
manufactured. The nature of the hint will of course be specific to
|
|
the nonvol group."
|
|
::= { v2FactNonVolEntry 10 }
|
|
|
|
v2NonVolIsManufacturedDynamic OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Reports whether the dynamic section of this non-volatile storage
|
|
group has been sufficiently manufactured. Criteria for manufacturing
|
|
are of course specific to a given group. Software implementations may
|
|
take some kind of action to limit private MIB access once all nonvol
|
|
groups report that they are manufactured."
|
|
::= { v2FactNonVolEntry 11 }
|
|
|
|
v2NonVolMfgHintDynamic OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If v2NonVolIsManufacturedDynamic is false(2), this object reports
|
|
a textual hint as to which settings in the group have not yet been
|
|
manufactured. The nature of the hint will of course be specific to
|
|
the nonvol group."
|
|
::= { v2FactNonVolEntry 12 }
|
|
|
|
|
|
-- v2NonVolControl group. Used to restore NV defaults, as well as perform
|
|
-- other NV related operations TBD (eg TFTP image).
|
|
v2NonVolControl OBJECT IDENTIFIER ::= { v2FactoryNonVol 2 }
|
|
|
|
v2NonVolControlGroup OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies which entry in the v2FactNonVolTable will be affected by
|
|
control operations from this group. Must be either a value of
|
|
v2NonVolIndex or zero. If zero is used, the control operation will
|
|
be applied to all groups."
|
|
DEFVAL { 0 }
|
|
::= { v2NonVolControl 1 }
|
|
|
|
v2NonVolControlSection OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
permanent(1),
|
|
dynamic(2),
|
|
both(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies which section of the group identified by
|
|
v2NonVolControlGroup will be affected by control operations from this
|
|
group."
|
|
DEFVAL { both }
|
|
::= { v2NonVolControl 2 }
|
|
|
|
v2NonVolRestoreDefaults OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"When set to true(1), causes the group identified by
|
|
v2NonVolControlGroup to have its values restored to factory defaults.
|
|
Always returns false(2) when read. Setting to false(2) has no
|
|
effect."
|
|
::= { v2NonVolControl 3 }
|
|
|
|
v2NonVolTftpServer OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls and reflects the IP address of a TFTP server from which
|
|
non-vol settings will be downloaded if v2NonVolDloadNow is set to
|
|
true(1), into the group specified in v2NonVolControlGroup."
|
|
::= { v2NonVolControl 4 }
|
|
|
|
v2NonVolTftpPath OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls and reflects the path of a file on a TFTP server from which a
|
|
non-vol settings will be downloaded if v2NonVolDloadNow is set to
|
|
true(1), into the group specified in v2NonVolControlGroup."
|
|
::= { v2NonVolControl 5 }
|
|
|
|
v2NonVolDloadNow OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If set to true(1), a new non vol image will be downloaded from the IP
|
|
address specified by v2NonVolDloadTftpServer, the file to download
|
|
having been specified by v2NonVolDloadTftpPath."
|
|
::= { v2NonVolControl 6 }
|
|
|
|
v2NonVolDloadStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
failure(0),
|
|
success(1),
|
|
inProgress(2),
|
|
other(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the status of the last non-vol download attempt."
|
|
::= { v2NonVolControl 7 }
|
|
|
|
v2NonVolDelExtraData OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Setting this object to true(1) will get rid of any extra data that is
|
|
assiociated with the settings group specified by v2NonVolControlGroup
|
|
and the section specified by v2NonVolControlSection. The extra data
|
|
is usually caused by a downgrade, where settings written by a newer
|
|
version are not understood by the older version, but are stored so that
|
|
they will still exist when the new code is run. However, in some
|
|
cases, it is desirable to get rid of them if they are not going to be
|
|
used. Always returns false(2) when read."
|
|
::= { v2NonVolControl 8 }
|
|
|
|
v2NonVolFlush OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Setting this object to true(1) will flush out any unrecognized groups
|
|
that were read from the device. This is useful in cases where the
|
|
settings group isn't needed by another application, and would just
|
|
waste space. Note that this operation occurs over all groups and
|
|
sections, so the values of v2NonVolControlGroup and
|
|
v2NonVolControlSection are ignored when this operation is invoked.
|
|
Always returns false(2) when read."
|
|
::= { v2NonVolControl 9 }
|
|
|
|
v2NonVolClearDevice OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Setting this object to true(1) will tell the nonvol device to wipe out
|
|
the section specified in v2NonVolControlSection. All data will be
|
|
lost; the device should be restored to its 'virgin' state. For flash
|
|
devices, the flash block is erased; for disk devices, the file is
|
|
erased. Note that this operation occurs over all groups, so the value
|
|
of v2NonVolControlGroup is ignored by this operation. Always returns
|
|
false(2) when read."
|
|
::= { v2NonVolControl 10 }
|
|
|
|
-- v2FactoryImages: objects to control V2 specific image information
|
|
v2FactoryImages OBJECT IDENTIFIER ::= { v2Factory 2 }
|
|
|
|
-- v2FactoryBootloader: bootloader information and control objects
|
|
v2ImagesBootloader OBJECT IDENTIFIER ::= { v2FactoryImages 1 }
|
|
|
|
v2BootloaderVersion OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the version of the bootloader."
|
|
::= { v2ImagesBootloader 1 }
|
|
|
|
v2BootloaderSignature OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the signature that the bootloader uses to validate
|
|
downloaded firmware images. The signature in the image must match
|
|
this signature or the image will not be run. Note that if a bootloader
|
|
is not built with an image signature, then it will return the board's
|
|
chip ID."
|
|
::= { v2ImagesBootloader 2 }
|
|
|
|
v2BootloaderBoardInfo OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the board information for this board."
|
|
::= { v2ImagesBootloader 3 }
|
|
|
|
v2BootloaderCompressionSupport OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
cmpLZRLE(0),
|
|
cmpMiniLZ(1),
|
|
cmpReserved(2), -- skipped
|
|
cmpNRV2D99(3),
|
|
cmpLZMA(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies which compression schemes this bootloader supports. Older
|
|
bootloader versions may not support all compression schemes."
|
|
::= { v2ImagesBootloader 4 }
|
|
|
|
v2BootloaderIncompatibleImageCheckEnabled OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls and reflects whether the bootloader will perform a compatible
|
|
image check prior to executing an image. If set to true(1), an image
|
|
will not be executed if its compression type and signature are deemed
|
|
to be incompatible with the system. If set to false(2), these checks
|
|
are not performed and only CRC and HCS checks are done."
|
|
DEFVAL { true }
|
|
::= { v2ImagesBootloader 5 }
|
|
|
|
v2BootloaderDloadTftpServer OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls and reflects the IP address of a TFTP server from which a
|
|
new bootloader will be downloaded if v2BootloaderDloadNow is set to
|
|
true(1)"
|
|
::= { v2ImagesBootloader 6 }
|
|
|
|
v2BootloaderDloadTftpPath OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls and reflects the path of a file on a TFTP server from which a
|
|
new bootloader will be downloaded if v2BootloaderDloadNow is set to
|
|
true(1)"
|
|
::= { v2ImagesBootloader 7 }
|
|
|
|
v2BootloaderDloadNow OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If set to true(1), a new bootloader will be downloaded from the IP
|
|
address specified by v2BootloaderDloadTftpServer, the file to download
|
|
having been specified by v2BootloaderDloadTftpPath."
|
|
::= { v2ImagesBootloader 8 }
|
|
|
|
v2BootloaderDloadStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
failure(0),
|
|
success(1),
|
|
inProgress(2),
|
|
other(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the status of the last bootloader download attempt."
|
|
::= { v2ImagesBootloader 9 }
|
|
|
|
-- v2FactoryFirmware: firmware information and control objects
|
|
v2ImagesFirmware OBJECT IDENTIFIER ::= { v2FactoryImages 2 }
|
|
|
|
v2FirmwareTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF V2FirmwareEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A table of firmware images on this device."
|
|
::= { v2ImagesFirmware 1 }
|
|
|
|
v2FirmwareEntry OBJECT-TYPE
|
|
SYNTAX V2FirmwareEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"An entry describing the characteristics of a single firmware image."
|
|
INDEX { v2FwIndex }
|
|
::= { v2FirmwareTable 1 }
|
|
|
|
V2FirmwareEntry ::=
|
|
SEQUENCE {
|
|
v2FwIndex Integer32,
|
|
v2FwSignature Unsigned32,
|
|
v2FwControl BITS,
|
|
v2FwRevision DisplayString,
|
|
v2FwBuildTime DateAndTime,
|
|
v2FwFileSize Unsigned32,
|
|
v2FwMaxImageSize Unsigned32,
|
|
v2FwFileName DisplayString,
|
|
v2FwHCS Unsigned32,
|
|
v2FwCRC Unsigned32
|
|
}
|
|
|
|
v2FwIndex OBJECT-TYPE
|
|
SYNTAX Integer32 (1..2)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the instance number of this entry."
|
|
::= { v2FirmwareEntry 1 }
|
|
|
|
v2FwSignature OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the firmware signature with which this image was built.
|
|
If compatible image checking is enabled on the bootloader via
|
|
v2BootloaderIncompatibleImageCheckEnabled being set to true(1), then
|
|
this signature must match that of the bootloader in order for the
|
|
image to be executed."
|
|
::= { v2FirmwareEntry 2 }
|
|
|
|
-- v2FwControl: R/O UINT16
|
|
v2FwControl OBJECT-TYPE
|
|
SYNTAX BITS {
|
|
cmpLZRLE(0),
|
|
cmpMiniLZ(1),
|
|
cmpReserved(2), -- skipped
|
|
cmpNRV2D99(3),
|
|
cmpLZMA(4)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A mask of flags indicating control parameters for this image. Bits
|
|
0-7 are used to indicate compression type, and higer order bits
|
|
are reserved."
|
|
::= { v2FirmwareEntry 3 }
|
|
|
|
v2FwRevision OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identifies the version of this software in the format major.minor."
|
|
::= { v2FirmwareEntry 4 }
|
|
|
|
v2FwBuildTime OBJECT-TYPE
|
|
SYNTAX DateAndTime
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The date and time that this image was built."
|
|
::= { v2FirmwareEntry 5 }
|
|
|
|
v2FwFileSize OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The size of this image. Note that if an image is compressed, this
|
|
value indicates the compressed size."
|
|
::= { v2FirmwareEntry 6 }
|
|
|
|
v2FwMaxImageSize OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The maximum size image that may be stored to this image location.
|
|
Note that if an image is compressed, this value indicates the
|
|
compressed size."
|
|
::= { v2FirmwareEntry 7 }
|
|
|
|
v2FwFileName OBJECT-TYPE
|
|
SYNTAX DisplayString
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The name of the file from which this image was produced. Note that the
|
|
file name is extracted from the program store header, so it is possible
|
|
that this object will not match the actual filename of a downloaded
|
|
file if the file is renamed prior to the download."
|
|
::= { v2FirmwareEntry 8 }
|
|
|
|
v2FwHCS OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The header checksum used by the bootloader when validating this image."
|
|
::= { v2FirmwareEntry 9 }
|
|
|
|
v2FwCRC OBJECT-TYPE
|
|
SYNTAX Unsigned32
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The cyclic redundancy code used by the bootloader when validating this
|
|
image."
|
|
::= { v2FirmwareEntry 10 }
|
|
|
|
-- v2FirmwareControl group contains objects for downloading, copying, or
|
|
-- deleting an image.
|
|
v2FirmwareControl OBJECT IDENTIFIER ::= { v2ImagesFirmware 2 }
|
|
|
|
v2FwControlImageNumber OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the image from the v2ImageTable which will be controlled by
|
|
operations from this group. Must be set to a valid value of
|
|
v2FwIndex."
|
|
::= { v2FirmwareControl 1 }
|
|
|
|
v2FwDloadTftpServer OBJECT-TYPE
|
|
SYNTAX IpAddress
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls and reflects the IP address of a TFTP server from which the
|
|
image specified in v2FwControlImageNumber will be downloaded if
|
|
v2FwDloadNow is set to true(1). Equivalent to the IpAddress argument
|
|
in the Docsis/dload command from the V2 CLI."
|
|
::= { v2FirmwareControl 2 }
|
|
|
|
v2FwDloadTftpPath OBJECT-TYPE
|
|
SYNTAX SnmpAdminString
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Controls and reflects the path to a file on the server specified by
|
|
v2FwDloadTftpServer which will be downloaded to the image specified
|
|
by v2FwControlImageNumber if v2FwDloadNow is set to true(1).
|
|
Equivalent to the Filename argument in the Docsis/dload command from
|
|
the V2 CLI."
|
|
::= { v2FirmwareControl 3 }
|
|
|
|
v2FwDloadLarge OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If set to true, a large image may be downloaded into image 1 such that
|
|
it spans into image 2. This allows a 'fat' image to be downloaded
|
|
onto a 'slim' board, but it will destroy an existing image in image2.
|
|
Equivalent to the -l argument in the Docsis/dload command from the
|
|
V2 CLI."
|
|
DEFVAL { false }
|
|
::= { v2FirmwareControl 4 }
|
|
|
|
v2FwDloadForce OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If set to true, the application will not perform any image validation
|
|
on the image program header prior to loading an image. This would
|
|
mainly be used to allow an image with an unmatching signature to be
|
|
downloaded, but use caution because this will also allow images for
|
|
the wrong chip type, or completely invalid files to be downloaded.
|
|
Equivalent to the -f argument in the Docsis/dload command from the
|
|
V2 CLI."
|
|
DEFVAL { false }
|
|
::= { v2FirmwareControl 5 }
|
|
|
|
v2FwDloadNow OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If set to true, a TFTP download will begin which will load the image
|
|
from the TFTP server specified in v2FwDloadTftpServer using the file
|
|
specified in v2FwDloadTftpPath to the image specified in
|
|
v2FwControlImageNumber. When read, always returns false(2)."
|
|
::= { v2FirmwareControl 6 }
|
|
|
|
v2FwDloadStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
failure(0),
|
|
success(1),
|
|
inProgress(2),
|
|
other(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the status of the last (or current) firmware image download
|
|
attempt."
|
|
::= { v2FirmwareControl 7 }
|
|
|
|
v2FwDeleteImage OBJECT-TYPE
|
|
SYNTAX TruthValue
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If set to true(1), the image indicated by v2FwControlImageNumber will
|
|
be deleted. Equivalent to the Docsis/clear_image command from the
|
|
V2 CLI."
|
|
::= { v2FirmwareControl 8 }
|
|
|
|
v2FwCopyImageFrom OBJECT-TYPE
|
|
SYNTAX Integer32
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If this object is set, the image specified by v2FwControlImageNumber
|
|
will be overwritten by the image specified by this object. Equivalent
|
|
to the Docsis/copy_image command from the CLI as if it is issued as
|
|
copy_image v2FwCopyImageFrom v2FwControlImageNumber."
|
|
::= { v2FirmwareControl 9 }
|
|
|
|
v2FwCopyStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
failure(0),
|
|
success(1),
|
|
inProgress(2),
|
|
other(3)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Indicates the status of the last firmware copy attempt."
|
|
::= { v2FirmwareControl 10 }
|
|
|
|
END
|