WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/bintec/BIANCA-BRICK-X25-MIB

2841 lines
81 KiB
Plaintext
Raw Permalink Blame History

-- This file is corresponding to Release 9.1.10.101 from 2014/08/11 00:00:00
-- (C)opyright 1991-2014 bintec elmeg GmbH, All Rights Reserved
-- $RCSfile: mibx25,v $
-- $Revision: 1.56 $
BIANCA-BRICK-X25-MIB DEFINITIONS ::= BEGIN
IMPORTS
IpAddress, Counter, TimeTicks, enterprises
FROM RFC1155-SMI
DisplayString
FROM RFC1158-MIB
Date, HexValue, BitValue
FROM BINTEC-MIB
OBJECT-TYPE
FROM RFC-1212;
bintec OBJECT IDENTIFIER ::= { enterprises 272 }
bibo OBJECT IDENTIFIER ::= { bintec 4 }
x25 OBJECT IDENTIFIER
::= { bibo 6 }
-- X.25 Group
-- Management Information for the X.25 Subsystem of the BIANCA/BRICK
x25LinkTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25LinkEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains an entry for each active link. There
may be mutiple active links per interface. For point-to-
multipoint interfaces, the field x25LkAddr specifies
the (MAC-) address of the partner, the link leads to.
There may be also multiple links for a point-to-point
interface in a multilink environment without a multilink-
protocol joining the multiple links to a singe logical
link."
::= { x25 1 }
x25LinkEntry OBJECT-TYPE
SYNTAX X25LinkEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The x25LinkEntry is created automatically, when a link
becomes active. The entry is also removed automatically,
if a link becomes disconnected. It may be removed manually
by setting the field x25LinkState to delete, which causes the
related link to be disconnected."
INDEX { x25LkIfIndex }
::= { x25LinkTable 1 }
X25LinkEntry ::=
SEQUENCE {
x25LkIfIndex INTEGER,
x25LkAddr OCTET STRING,
x25LkMode INTEGER,
x25LkModulo INTEGER,
x25LkLIC INTEGER,
x25LkHIC INTEGER,
x25LkLTC INTEGER,
x25LkHTC INTEGER,
x25LkLOC INTEGER,
x25LkHOC INTEGER,
x25LkDefPktSize INTEGER,
x25LkDefWinSize INTEGER,
x25LkMaxPktSize INTEGER,
x25LkMaxWinSize INTEGER,
x25LkL2WinSize INTEGER,
x25LkL2RetrTimer INTEGER,
x25LkL2RetrCounter INTEGER,
x25LkL2SupervTimer INTEGER,
x25LkL2IdleTimer INTEGER,
x25LkState INTEGER,
x25LkNegotiation INTEGER,
x25LkDiscDelayTimer INTEGER,
x25LkCallDelayTimer INTEGER,
x25LkRestDelayTimer INTEGER,
x25LkRewritingRule INTEGER,
x25LkL1IdleTimer INTEGER,
x25LkActSabmDelayTimer INTEGER,
x25LkPsvSabmDelayTimer INTEGER
}
x25LkIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The index of the interface the link is running on.
See ifTable."
::= { x25LinkEntry 1 }
x25LkAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"On point-to-multipoint interfaces, this field contains the
(MAC-)address of the partner, the link is leading to.
It is empty for point-to-point interfaces, because there
is only one partner at the other side."
::= { x25LinkEntry 2 }
x25LkMode OBJECT-TYPE
SYNTAX INTEGER {
dte(1), dce(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This field indicates wheter the Layer 3 on top of the link
is operated in DTE or DCE mode. The difference is in the
order of VC-assignment, the handling of a call collision
and the range of allowed values of the cause field."
DEFVAL { dte }
::= { x25LinkEntry 3 }
x25LkModulo OBJECT-TYPE
SYNTAX INTEGER {
mod8(1), mod128(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This field indicates whether the layer 3 on top of the link
is in modulo 8 or in modulo 128 mode."
DEFVAL { mod8 }
::= { x25LinkEntry 4 }
x25LkLIC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Lowest Incoming Channel as seen from the DTE. The value
-1 means no incoming channels."
::= { x25LinkEntry 5 }
x25LkHIC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Highest Incoming Channel as seen from the DTE. The value
-1 means no incoming channels."
::= { x25LinkEntry 6 }
x25LkLTC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Lowest Twoway Channel as seen from the DTE. The value
-1 means no twoway channels."
::= { x25LinkEntry 7 }
x25LkHTC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Highest Twoway Channel as seen from the DTE. The value
-1 means no twoway channels."
::= { x25LinkEntry 8 }
x25LkLOC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Lowest Outgoing Channel as seen from the DTE. The value
-1 means no outgoing channels."
::= { x25LinkEntry 9 }
x25LkHOC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Highest Outgoing Channel as seen from the DTE. The value
-1 means no outgoing channels."
::= { x25LinkEntry 10 }
x25LkDefPktSize OBJECT-TYPE
SYNTAX INTEGER {
p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The default layer 3 packet size for this link."
DEFVAL { p128 }
::= { x25LinkEntry 11 }
x25LkDefWinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The default window size. This is always less than 8, if the
layer 3 is operated in modulo 8 mode."
::= { x25LinkEntry 12 }
x25LkMaxPktSize OBJECT-TYPE
SYNTAX INTEGER {
unrestricted(1), p128(7), p256(8), p512(9), p1024(10),
p2048(11), p4096(12)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum allowable packet size for this link during
X.25 packet size negotiation. If this field is set to
unrestricted, the packet size will only be limited by
the Mtu size of the interface, which is always the
upper bound for the packet size."
DEFVAL { unrestricted }
::= { x25LinkEntry 13 }
x25LkMaxWinSize OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The maximum allowable window size for this link during
window size negotiation."
::= { x25LinkEntry 14 }
x25LkL2WinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The layer 2 window size for this link."
::= { x25LinkEntry 15 }
x25LkL2RetrTimer OBJECT-TYPE
SYNTAX INTEGER (100..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The retransmission timeout in milliseconds for the
layer 2 of this link. If a frame is not acknowledged within
this timeout, it will be retransmitted."
::= { x25LinkEntry 16 }
x25LkL2RetrCounter OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The retransmission counter for the layer 2 of this link.
If a frame has been retransmitted more often than indicated
by this object, the link will be reset or disconnected,"
::= { x25LinkEntry 17 }
x25LkL2SupervTimer OBJECT-TYPE
SYNTAX INTEGER (100..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The link-supervision timeout in milliseconds for the
layer 2 of this link. This timer is started, when the
link gets idle. An RR poll-sequence will be initiated,
when this timeout expires."
::= { x25LinkEntry 18 }
x25LkL2IdleTimer OBJECT-TYPE
SYNTAX INTEGER (-1..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The idle timer in milliseconds for the layer 2 of this
link. If no VCs are established and the the link has been
idle for the time specified by this object, the link
will be disconnected. The value 1 means, that the link is
disconnected immediately when the last VC has been cleared.
The value 0 means, the link should not be disconnected
after the last VC has been cleared. A value of -1 means,
that the link shall be kept up even if it get disconnected
from the partner on the other end."
::= { x25LinkEntry 19 }
x25LkState OBJECT-TYPE
SYNTAX INTEGER {
restart-pending(1), restart-collision(2), ready(3),
disc-pending(4),
reset-pending(5), sabm-pending(6),
xid-pending(7), sabm-wait(8),
l1connect-pending(9), l1-ready(10)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the current state of the link. The
link may be manually disconnected by setting this object
to the value delete."
DEFVAL { restart-pending }
::= { x25LinkEntry 20 }
x25LkNegotiation OBJECT-TYPE
SYNTAX INTEGER { when-necessary(1), always(2), never(3) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object determines whether packet-size and windows-size
parameters are negotiated for outgoing calls. When set to
never, outgoing calls are cleared if the call parameters
differ from the default-settings. When set to when-necessary,
negotiation is only performed if the call parameters differ
from the default settings. When set to always, negotiation
is always performed."
DEFVAL { when-necessary }
::= { x25LinkEntry 21 }
x25LkDiscDelayTimer OBJECT-TYPE
SYNTAX INTEGER (0..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The disc delay timer in milliseconds for the layer 2 of
this link (only outgoing links). This timer specifies the
time interval between receiving of layer 2 disconnect and
actual disconnect of link. If the partner want to
disconnect the layer 2 and the time specified by this object
expired, the link will be disconnected. The value 0 means,
the link will be disconnected immediately after receiving of
disconnect."
::= { x25LinkEntry 22 }
x25LkCallDelayTimer OBJECT-TYPE
SYNTAX INTEGER (0..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The call delay timer in milliseconds for the layer 3 of
this link (only outgoing link). This timer specifies the
time interval between restart procedure completion and
virtual call setup. If restart procedure is completed
and the time specified by this object expired, call packet
will be sent. The value 0 means, call packet should be sent
immediately after completion of restart procedure."
::= { x25LinkEntry 23 }
x25LkRestDelayTimer OBJECT-TYPE
SYNTAX INTEGER (0..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Restart delay timer in milliseconds for this link.
This timer specifies the time interval between
establishment of layer 2 and sending of restart packet.
If layer 2 is established and the time specified by this
object expired, restart packet will be sent.
The value 0 means, restart packet should be sent immediately
after establishment of layer 2."
::= { x25LinkEntry 24 }
x25LkRewritingRule OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This Object specifies a rewriting rule in the X25 Rewrite
table. The call packet will be processed according
to this rewriting rule before the call is being routed.
If this value is set to zero, no rewriting will take
place."
::= { x25LinkEntry 25 }
x25LkL1IdleTimer OBJECT-TYPE
SYNTAX INTEGER (-1..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The idle timer in milliseconds for the layer 1 of this
link. If layer 2 is disconnected and the time specified
by this object expired, the layer 1 will be disconnected.
The value 0 means, the layer 1 should not be disconnected
after the layer 2 is disconnected.
A value of -1 means, that the layer 1 shall be kept up
even if it get disconnected from the partner on the
other end."
::= { x25LinkEntry 26 }
x25LkActSabmDelayTimer OBJECT-TYPE
SYNTAX INTEGER (-1..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The sabm delay timer in milliseconds for this link (only
dialup outgoing link). This timer specifies the time interval
between establishment of layer 1 and sending of SABM packet.
If layer 1 is established and the time specified by this
object expired, SABM packet will be sent. The value 0
means, SABM packet should be sent immediately after
establishment of layer 1. The value -1 means, SABM packet
should not be sent by dialup outgoing link."
::= { x25LinkEntry 32 }
x25LkPsvSabmDelayTimer OBJECT-TYPE
SYNTAX INTEGER (-1..30000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The passive sabm delay timer in milliseconds for this
link (only dialup incoming link). This timer specifies the time
interval between establishment of layer 1 and sending of SABM
packet. If layer 1 is established and the time specified by
this object expired, SABM packet will be sent. The value 0
means, SABM packet should be sent immediately after
establishment of layer 1. The value -1 means, SABM packet
should not be sent by dialup incoming link."
::= { x25LinkEntry 33 }
x25LinkPresetTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25LinkPresetEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table predefines the link-parameters to be used,
when a link is created. If no entry is contained
in this table for a particular link, it will be setup
with the default values. In any case, the parameters
finally choosen for a link are displayed in the x25LinkTable.
For point-to-multipoint interfaces, the parameters
for the link may be set for all connected partners
(x25LkPrAddr is empty) of for the specific partners
individually (x25LkPrAddr is the MAC-address of the
partner)."
::= { x25 2 }
x25LinkPresetEntry OBJECT-TYPE
SYNTAX X25LinkPresetEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries in this table are created by defining a new value
for the field x25LkPrIfIndex. Entries may be deleted by
setting the field x25LkPrMode to the value delete. Please
note, that changing the entries dont have influence
on links being already established. To take effekt the
according links have to be cleared either manually
(see x25LinkTable) or by other means."
INDEX { x25LkPrIfIndex }
::= { x25LinkPresetTable 1 }
X25LinkPresetEntry ::=
SEQUENCE {
x25LkPrIfIndex INTEGER,
x25LkPrAddr OCTET STRING,
x25LkPrMode INTEGER,
x25LkPrModulo INTEGER,
x25LkPrLIC INTEGER,
x25LkPrHIC INTEGER,
x25LkPrLTC INTEGER,
x25LkPrHTC INTEGER,
x25LkPrLOC INTEGER,
x25LkPrHOC INTEGER,
x25LkPrDefPktSize INTEGER,
x25LkPrDefWinSize INTEGER,
x25LkPrMaxPktSize INTEGER,
x25LkPrMaxWinSize INTEGER,
x25LkPrL2WinSize INTEGER,
x25LkPrL2RetrTimer INTEGER,
x25LkPrL2RetrCounter INTEGER,
x25LkPrL2SupervTimer INTEGER,
x25LkPrL2IdleTimer INTEGER,
x25LkPrNegotiation INTEGER,
-- x25LkPrDiscDelayTimer INTEGER,
-- x25LkPrCallDelayTimer INTEGER,
x25LkPrRestDelayTimer INTEGER,
x25LkPrVC0 INTEGER,
x25LkPrRewritingRule INTEGER
--, x25LkPrL1IdleTimer INTEGER,
--x25LkPrActSabmDelayTimer INTEGER,
--x25LkPrPsvSabmDelayTimer INTEGER
}
x25LkPrIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The interface index of the link to be predefined. This
object identifies a row in the ifTable."
::= { x25LinkPresetEntry 1 }
x25LkPrAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"On point-to-point links, this field must be empty. On
point-to-multipoint links, this field may be empty or
set to a partners (MAC-) address. In the first case, the
definition is valid for all links on the interface
except for those having a specific predefiniton.
In the second case the definition defines the link parameters
for a specific partner."
::= { x25LinkPresetEntry 2 }
x25LkPrMode OBJECT-TYPE
SYNTAX INTEGER {
dte(1), dce(2), delete(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This field indicates, whether the link is initially operated
in DTE or DCE mode. If a misconfiguration is detected,
(DTE<->DTE od DCE<->DCE) the DTE/DCE assignement is done
be means of the procedure defined in ISOxxxx."
DEFVAL { dte }
::= { x25LinkPresetEntry 3 }
x25LkPrModulo OBJECT-TYPE
SYNTAX INTEGER {
mod8(1), mod128(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object indicates, whether the link should be operated
in modulo 8 or modulo 128 mode."
DEFVAL { mod8 }
::= { x25LinkPresetEntry 4 }
x25LkPrLIC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest Incoming Channel as seen from the DTE. Depending
on the value of x25LkPrVC0, the value of -1 or Zero means
no incoming channels."
DEFVAL { -1 }
::= { x25LinkPresetEntry 5 }
x25LkPrHIC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest Incoming Channel as seen from the DTE. Depending
on the value of x25LkPrVC0, the value of -1 or Zero means
no incoming channels."
DEFVAL { -1 }
::= { x25LinkPresetEntry 6 }
x25LkPrLTC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest Twoway Channel as seen from the DTE. Depending
on the value of x25LkPrVC0, the value of -1 or Zero means
no twoway channels."
DEFVAL { 1 }
::= { x25LinkPresetEntry 7 }
x25LkPrHTC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest Twoway Channel as seen from the DTE. Depending
on the value of x25LkPrVC0, the value of -1 or Zero means
no twoway channels."
DEFVAL { 1 }
::= { x25LinkPresetEntry 8 }
x25LkPrLOC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Lowest Outgoing Channel as seen from the DTE. Depending
on the value of x25LkPrVC0, the value of -1 or Zero means
no outgoing channels."
DEFVAL { -1 }
::= { x25LinkPresetEntry 9 }
x25LkPrHOC OBJECT-TYPE
SYNTAX INTEGER (-1..4095)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Highest Outgoing Channel as seen from the DTE. Depending
on the value of x25LkPrVC0, the value of -1 or Zero means
no outgoing channels."
DEFVAL { -1 }
::= { x25LinkPresetEntry 10 }
x25LkPrDefPktSize OBJECT-TYPE
SYNTAX INTEGER {
p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Layer 3 packet size for this link."
DEFVAL { p128 }
::= { x25LinkPresetEntry 11 }
x25LkPrDefWinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The default window size. This must be less than 8, if the
layer 3 is operated in modulo 8 mode."
DEFVAL { 2 }
::= { x25LinkPresetEntry 12 }
x25LkPrMaxPktSize OBJECT-TYPE
SYNTAX INTEGER {
unrestricted(1), p128(7), p256(8), p512(9), p1024(10),
p2048(11), p4096(12)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum allowable packet size for this link during
X.25 packet size negotiation. If this field is set to
unrestricted, the packet size will only be limited by
the Mtu size of the interface, which is always the
upper bound for the packet size."
DEFVAL { p128 }
::= { x25LinkPresetEntry 13 }
x25LkPrMaxWinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum allowable window size for this link during
window size negotiation."
DEFVAL { 2 }
::= { x25LinkPresetEntry 14 }
x25LkPrL2WinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The layer 2 window size for this link."
DEFVAL { 2 }
::= { x25LinkPresetEntry 15 }
x25LkPrL2RetrTimer OBJECT-TYPE
SYNTAX INTEGER (100..30000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The retransmission timeout in milliseconds for the
layer 2 of this link. If a frame is not acknowledged within
this timeout, it will be retransmitted."
DEFVAL { 1000 }
::= { x25LinkPresetEntry 16 }
x25LkPrL2RetrCounter OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The retransmission counter for the layer 2 of this link.
If a frame has been retransmitted more often than indicated
by this object, the link will be reset or disconnected."
DEFVAL { 10 }
::= { x25LinkPresetEntry 17 }
x25LkPrL2SupervTimer OBJECT-TYPE
SYNTAX INTEGER (100..30000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The link-supervision timeout in milliseconds for the
layer 2 of this link. This timer is started, when the
link gets idle. An RR poll-sequence will be initiated,
when this timeout expires."
DEFVAL { 10000 }
::= { x25LinkPresetEntry 18 }
x25LkPrL2IdleTimer OBJECT-TYPE
SYNTAX INTEGER (-1..30000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The idle timer in milliseconds for the layer 2 of this
link. If no VCs are established and the the link has been
idle for the time specified by this object, the link
will be disconnected. The value 0 means, the link should
not be disconnected after the last VC has been cleared.
A value of -1 means, that the link shall be kept up
even if it get disconnected from the partner on the
other end."
DEFVAL { 1 }
::= { x25LinkPresetEntry 19 }
x25LkPrNegotiation OBJECT-TYPE
SYNTAX INTEGER { when-necessary(1), always(2), never(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object determines whether packet-size and windows-size
parameters are negotiated for outgoing calls. When set to
never, outgoing calls are cleared if the call parameters
differ from the default-settings. When set to when-necessary,
negotiation is only performed if the call parameters differ
from the default settings. When set to always, negotiation
is always performed."
DEFVAL { when-necessary }
::= { x25LinkPresetEntry 20 }
-- x25LkPrDiscDelayTimer OBJECT-TYPE
-- SYNTAX INTEGER (0..30000)
-- ACCESS read-write
-- STATUS mandatory
--
-- DESCRIPTION
-- "The disc delay timer in milliseconds for the layer 2 of
-- this link (only outgoing links). This timer specifies the
-- time interval between receiving of layer 2 disconnect and
-- actual disconnect of link. If the partner want to
-- disconnect the layer 2 and the time specified by this object
-- expired, the link will be disconnected. The value 0 means,
-- the link will be disconnected immediately after receiving of
-- disconnect."
-- DEFVAL { 0 }
-- ::= { x25LinkPresetEntry 21 }
--
-- x25LkPrCallDelayTimer OBJECT-TYPE
-- SYNTAX INTEGER (0..30000)
-- ACCESS read-write
-- STATUS mandatory
--
-- DESCRIPTION
-- "The call delay timer in milliseconds for the layer 3 of
-- this link (only outgoing link). This timer specifies the
-- time interval between restart procedure completion and
-- virtual call setup. If restart procedure is completed
-- and the time specified by this object expired, call packet
-- will be sent. The value 0 means, call packet should be sent
-- immediately after completion of restart procedure."
-- DEFVAL { 0 }
-- ::= { x25LinkPresetEntry 22 }
x25LkPrRestDelayTimer OBJECT-TYPE
SYNTAX INTEGER (0..30000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Restart delay timer in milliseconds for this link.
This timer specifies the time interval between
establishment of layer 2 and sending of restart packet.
If layer 2 is established and the time specified by this
object expired, restart packet will be sent.
The value 0 means, restart packet should be sent immediately
after establishment of layer 2."
DEFVAL { 0 }
::= { x25LinkPresetEntry 23 }
x25LkPrVC0 OBJECT-TYPE
SYNTAX INTEGER {
enable(1), disable(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object indicates, whether VC#0 shall be allowed on
the link. If this object is set to enable, VC#0 is allowed
and the value -1 shall be used to indicate the absence of
specified channels. This invalidates old configurations,
for which a value of 0 specifies the absense of a specified
channel. However, for compatibility reasons, if this object
is not set to enabled, the values -1 or 0 may be used to
specify the absence of a channel."
DEFVAL { disable }
::= { x25LinkPresetEntry 24 }
x25LkPrRewritingRule OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This Object specifies a rewriting rule in the X25 Rewrite
table. The call packet will be processed according
to this rewriting rule before the call is being routed.
If this value is set to zero, no rewriting will take
place."
::= { x25LinkPresetEntry 25 }
-- x25LkPrL1IdleTimer OBJECT-TYPE
-- SYNTAX INTEGER (-1..30000)
-- ACCESS read-write
-- STATUS mandatory
--
-- DESCRIPTION
-- ""
-- DEFVAL { 1 }
-- ::= { x25LinkPresetEntry 26 }
--
-- x25LkPrActSabmDelayTimer OBJECT-TYPE
-- SYNTAX INTEGER (-1..30000)
-- ACCESS read-write
-- STATUS mandatory
--
-- DESCRIPTION
-- ""
-- DEFVAL { 0 }
-- ::= { x25LinkPresetEntry 32 }
--
-- x25LkPrPsvSabmDelayTimer OBJECT-TYPE
-- SYNTAX INTEGER (-1..30000)
-- ACCESS read-write
-- STATUS mandatory
--
-- DESCRIPTION
-- ""
-- DEFVAL { -1 }
-- ::= { x25LinkPresetEntry 33 }
x25CallTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25CallEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains an entry for each active X25-call.
Calls always lead from a source-link to a destination-link.
An interface index of 1 denotates a pseudo interfaces
corresponding to all locally terminated calls."
::= { x25 3 }
x25CallEntry OBJECT-TYPE
SYNTAX X25CallEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The entries are created automatically, as soon as a call
gets active. They are removed automatically as soon as
a call gets completely cleared. A call may also be cleared
manually by setting the x25CallState field of an entry to
the value delete, which would also force the call to be
cleared. The call data of a cleared call is copied to
the x25CallHistoryTable."
INDEX {
x25CallSrcIfIndex, x25CallSrcVCNumber,
x25CallDstIfIndex, x25CallDstVCNumber
}
::= { x25CallTable 1 }
X25CallEntry ::=
SEQUENCE {
x25CallSrcIfIndex INTEGER,
x25CallSrcLinkAddr OCTET STRING,
x25CallSrcVCNumber INTEGER,
x25CallDstIfIndex INTEGER,
x25CallDstLinkAddr OCTET STRING,
x25CallDstVCNumber INTEGER,
x25CallSrcAddr DisplayString,
x25CallDstAddr DisplayString,
x25CallProtocolId INTEGER,
x25CallFacilities OCTET STRING,
x25CallUserData DisplayString,
x25CallAge TimeTicks,
x25CallState INTEGER,
x25CallInPktSize INTEGER,
x25CallOutPktSize INTEGER,
x25CallInWinSize INTEGER,
x25CallOutWinSize INTEGER,
x25CallPktsSent Counter,
x25CallBytesSent Counter,
x25CallPktsRecvd Counter,
x25CallBytesRecvd Counter
}
x25CallSrcIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The interface index of the link, the call comes from.
This object contains the value 1, when the call is
originated locally."
::= { x25CallEntry 1 }
x25CallSrcLinkAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The (MAC-)address of the link, the call comes from (if any)"
::= { x25CallEntry 2 }
x25CallSrcVCNumber OBJECT-TYPE
SYNTAX INTEGER (1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The virtual curcuit number of the call on the link, the
call comes from."
::= { x25CallEntry 3 }
x25CallDstIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The interface index of the link, the call leads to. This
object contains the value 1, when the link is terminated
locally."
::= { x25CallEntry 4 }
x25CallDstLinkAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The (MAC-)address of the link, the call leads to."
::= { x25CallEntry 5 }
x25CallDstVCNumber OBJECT-TYPE
SYNTAX INTEGER (1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The virtual curcuit number of the call on the target link."
::= { x25CallEntry 6 }
x25CallSrcAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The calling address of the call as received on the source
link."
::= { x25CallEntry 7 }
x25CallDstAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The called address of the call as received on the source
link."
::= { x25CallEntry 8 }
x25CallProtocolId OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The protocol id (the first four byte of the call user data)
of the call as received from the source link."
::= { x25CallEntry 9 }
x25CallFacilities OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The facilities of the call as received from the source
link."
::= { x25CallEntry 10 }
x25CallUserData OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The user data (whithout the protocol id) of the call as
received from the source link."
::= { x25CallEntry 11 }
x25CallAge OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The age of the call since received from the source link."
::= { x25CallEntry 12 }
x25CallState OBJECT-TYPE
SYNTAX INTEGER {
routing(1), call-pending(2), dataxfer(3),
out-reset-pending(4), in-reset-pending(5),
out-clear-pending(6),
in-clear-pending(7)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The current state of the call. A call may be cleared manually
by setting this object to the value delete."
DEFVAL { routing }
::= { x25CallEntry 13 }
x25CallInPktSize OBJECT-TYPE
SYNTAX INTEGER {
p2(1), p4(2), p8(3), p16(4), p32(5), p64(6),
p128(7), p256(8), p512(9), p1024(10), p2048(11),
p4096(12), p8192(13), p16384(14), p32768(15)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The packet size of packets being received by the caller,
as negotiated by the negotiation procedure."
DEFVAL { p128 }
::= { x25CallEntry 14 }
x25CallOutPktSize OBJECT-TYPE
SYNTAX INTEGER {
p2(1), p4(2), p8(3), p16(4), p32(5), p64(6),
p128(7), p256(8), p512(9), p1024(10), p2048(11),
p4096(12), p8192(13), p16384(14), p32768(15)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The packet size of packets being sent by the caller,
as negotiated by the negotiation procedure."
DEFVAL { p128 }
::= { x25CallEntry 15 }
x25CallInWinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The window size of packets being received by the caller,
as negotiated by the negotiation procedure."
::= { x25CallEntry 16 }
x25CallOutWinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The window size of packets being sent by the caller,
as negotiated by the negotiation procedure."
::= { x25CallEntry 17 }
x25CallPktsSent OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of all layer 3 packets (including RR/RNR/REJ)
sent by the caller."
::= { x25CallEntry 18 }
x25CallBytesSent OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data bytes sent in DATA and INTERRUPT
packets by the caller."
::= { x25CallEntry 19 }
x25CallPktsRecvd OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of all layer 3 packets (including RR/RNR/REJ)
received by the caller."
::= { x25CallEntry 20 }
x25CallBytesRecvd OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data bytes received in DATA and INTERRUPT
packets by the caller."
::= { x25CallEntry 21 }
x25CallHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25CallHistoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table provides call information for the last 10 calls
after they have been cleared. Active call are not contained
in the x25CallHistoryTable."
::= { x25 4 }
x25CallHistoryEntry OBJECT-TYPE
SYNTAX X25CallHistoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries are created automatically, when a call is cleared
completely. The first entry is deleted automatcally, if a
new entry would be the 11th entry in the table."
INDEX { x25CallHistorySrcIfIndex, x25CallHistoryDstIfIndex }
::= { x25CallHistoryTable 1 }
X25CallHistoryEntry ::=
SEQUENCE {
x25CallHistoryTime Date,
x25CallHistoryDuration INTEGER,
x25CallHistorySrcIfIndex INTEGER,
x25CallHistorySrcLinkAddr OCTET STRING,
x25CallHistorySrcVCNumber INTEGER,
x25CallHistoryDstIfIndex INTEGER,
x25CallHistoryDstLinkAddr OCTET STRING,
x25CallHistoryDstVCNumber INTEGER,
x25CallHistorySrcAddr DisplayString,
x25CallHistoryDstAddr DisplayString,
x25CallHistoryProtocolId INTEGER,
x25CallHistoryFacilities OCTET STRING,
x25CallHistoryUserData DisplayString,
x25CallHistoryInPktSize INTEGER,
x25CallHistoryOutPktSize INTEGER,
x25CallHistoryInWinSize INTEGER,
x25CallHistoryOutWinSize INTEGER,
x25CallHistoryPktsSent Counter,
x25CallHistoryBytesSent Counter,
x25CallHistoryPktsRecvd Counter,
x25CallHistoryBytesRecvd Counter,
x25CallHistoryClearCause INTEGER,
x25CallHistoryClearDiag INTEGER
}
x25CallHistoryTime OBJECT-TYPE
SYNTAX Date
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Date and time, when the call was received."
::= { x25CallHistoryEntry 1 }
x25CallHistoryDuration OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Duration of the call in seconds."
::= { x25CallHistoryEntry 2 }
x25CallHistorySrcIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Interface index of the link, the call came from."
::= { x25CallHistoryEntry 3 }
x25CallHistorySrcLinkAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"(MAC-)address of the link, the call came from."
::= { x25CallHistoryEntry 4 }
x25CallHistorySrcVCNumber OBJECT-TYPE
SYNTAX INTEGER (1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Virtual Curcuit Number on the link, the call came from."
::= { x25CallHistoryEntry 5 }
x25CallHistoryDstIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Interface index of the link, the call leads to."
::= { x25CallHistoryEntry 6 }
x25CallHistoryDstLinkAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"(MAC-)address of the link, the call leads to."
::= { x25CallHistoryEntry 7 }
x25CallHistoryDstVCNumber OBJECT-TYPE
SYNTAX INTEGER (1..4095)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Virtual Curcuit Number on the link, the call leads to."
::= { x25CallHistoryEntry 8 }
x25CallHistorySrcAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The calling party number as received from the source link."
::= { x25CallHistoryEntry 9 }
x25CallHistoryDstAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The called party number as received from the source link."
::= { x25CallHistoryEntry 10 }
x25CallHistoryProtocolId OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The Protocol ID of the call (first four bytes of the call
user data field) as received from the source link."
::= { x25CallHistoryEntry 11 }
x25CallHistoryFacilities OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The facility field of the call as received from the
source link."
::= { x25CallHistoryEntry 12 }
x25CallHistoryUserData OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The call user data behind the protocol ID as received
from the source link"
::= { x25CallHistoryEntry 13 }
x25CallHistoryInPktSize OBJECT-TYPE
SYNTAX INTEGER {
p2(1), p4(2), p8(3), p16(4), p32(5), p64(6),
p128(7), p256(8), p512(9), p1024(10), p2048(11),
p4096(12), p8192(13), p16384(14), p32768(15)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The packet size of packets being received by the caller,
as negotiated by the negotiation procedure."
DEFVAL { p128 }
::= { x25CallHistoryEntry 14 }
x25CallHistoryOutPktSize OBJECT-TYPE
SYNTAX INTEGER {
p2(1), p4(2), p8(3), p16(4), p32(5), p64(6),
p128(7), p256(8), p512(9), p1024(10), p2048(11),
p4096(12), p8192(13), p16384(14), p32768(15)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The packet size of packets being sent by the caller,
as negotiated by the negotiation procedure."
DEFVAL { p128 }
::= { x25CallHistoryEntry 15 }
x25CallHistoryInWinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The window size of packets being received by the caller,
as negotiated by the negotiation procedure."
::= { x25CallHistoryEntry 16 }
x25CallHistoryOutWinSize OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The window size of packets being sent by the caller,
as negotiated by the negotiation procedure."
::= { x25CallHistoryEntry 17 }
x25CallHistoryPktsSent OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of all layer 3 packets (including RR/RNR/REJ)
sent by the caller."
::= { x25CallHistoryEntry 18 }
x25CallHistoryBytesSent OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data bytes sent in DATA and INTERRUPT
packets by the caller."
::= { x25CallHistoryEntry 19 }
x25CallHistoryPktsRecvd OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of all layer 3 packets (including RR/RNR/REJ)
received by the caller."
::= { x25CallHistoryEntry 20 }
x25CallHistoryBytesRecvd OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of data bytes received in DATA and INTERRUPT
packets by the caller."
::= { x25CallHistoryEntry 21 }
x25CallHistoryClearCause OBJECT-TYPE
SYNTAX INTEGER (-1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The clearing cause of the call as received in the first
clear packet. A value of -1 means, no cause was received."
::= { x25CallHistoryEntry 22 }
x25CallHistoryClearDiag OBJECT-TYPE
SYNTAX INTEGER (-1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The clearing diagnostics of the call as received in the first
clear packet. A value of -1 means, no diagnostics was
received."
::= { x25CallHistoryEntry 23 }
x25RouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25RouteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"The X.25 Routing Table specifies the target link for
different call parameters. For each incoming call the
route table will be searched for a matching entry. If
multiple entries match the call parameters, a metric
defines which of them to use. A route is only used, if
the state of the target interface is up or dormant (see
mib2). Also the state of the link is used to determine
wether to use the route or not. With this mechanism,
a rerouting scheme can be implemented."
::= { x25 5 }
x25RouteEntry OBJECT-TYPE
SYNTAX X25RouteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Entries can only be created and deleted manually."
INDEX { x25RtSrcIfIndex, x25RtDstIfIndex }
::= { x25RouteTable 1 }
X25RouteEntry ::=
SEQUENCE {
x25RtSrcIfIndex INTEGER,
x25RtSrcLinkAddr OCTET STRING,
x25RtDstIfIndex INTEGER,
x25RtDstLinkAddr OCTET STRING,
x25RtDstLinkAddrMode INTEGER,
x25RtSrcAddr DisplayString,
x25RtSrcNSAP DisplayString,
x25RtDstAddr DisplayString,
x25RtDstNSAP DisplayString,
x25RtProtocolId INTEGER,
x25RtCallUserData OCTET STRING,
x25RtRPOA INTEGER,
x25RtNUI DisplayString,
x25RtRewritingRule INTEGER,
x25RtMetric INTEGER,
x25RtCug INTEGER,
x25RtCugOutgoing INTEGER,
x25RtCugBilateral INTEGER,
x25RtDstLinkAddrRule DisplayString
}
x25RtSrcIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The originating interface index of the call. If this object
is set to zero, the originating interface index will not
be checked for the matching process. If this field is set to
one, the route is only valid for call originating locally."
DEFVAL { 0 }
::= { x25RouteEntry 1 }
x25RtSrcLinkAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The originating (MAC-)address of the call. If this object
is a zero length string, the originating address will not
be checked for the matching process."
::= { x25RouteEntry 2 }
x25RtDstIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The interface index the call has to be sent to. If this
value is set to one, the call will be used locally.
If the value is set to zero, the call will be refused. The
routing entry will only be used if the destination interface
status is up or dormant. Additionally the target link must
be in the state ready, if it is permanently activated, i.e.
the x25LkL2IdleTimer is set to -1."
DEFVAL { 0 }
::= { x25RouteEntry 3 }
x25RtDstLinkAddr OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The (MAC-)address of the station, the call has to be sent
to. This object is ignored for point-to-point interfaces."
::= { x25RouteEntry 4 }
x25RtDstLinkAddrMode OBJECT-TYPE
SYNTAX INTEGER {
default(1), direct(2), delete(3), rule(4), auto(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the way, the destination link address
is generated. Default will use the default method for the
target interface. When direct is selected, the destination
address is taken from the route entry. Set to rule(4), the
the address is generated according the rule defined in the
x25RtDstLinkAddrRule entry of the x25RouteTable.
Other methods will be developed in the future."
DEFVAL { default }
::= { x25RouteEntry 5 }
x25RtSrcAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The source X.121 address in the X25 call packet. If empty, the
source address will not be matched. Extended Adresses are
indicated by a leading '@'. The wildcards '*', '?', '[',
']', '{', '}' may be used."
::= { x25RouteEntry 6 }
x25RtSrcNSAP OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The source NSAP in the X25 call packet. If empty, the
source NSAP will not be matched. The NSAP is preceeded
by an 'X' if it is an OSI compatible NSAP or by a 'N' if
the NSAP is in a not OSI compatible format. The wildcards
'*', '?', '[', ']', '{', '}' may be used."
::= { x25RouteEntry 7 }
x25RtDstAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The target X.121 address in the X25 call packet. If empty, the
target address will not be matched. Extended Adresses are
indicated by a leading '@'. The wildcards '*', '?', '[',
']', '{', '}' may be used."
::= { x25RouteEntry 8 }
x25RtDstNSAP OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The target NSAP in the X25 call packet. If empty, the
target NSAP will not be matched. The NSAP is preceeded
by an 'X' if it is an OSI compatible NSAP or by a 'N' if
the NSAP is in a not OSI compatible format. The wildcards
'*', '?', '[', ']', '{', '}' may be used."
::= { x25RouteEntry 9 }
x25RtProtocolId OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The protocol id of the X25 call packet. The protocol id
will not be used for the matching process, when this
object is set to -1"
DEFVAL { -1 }
::= { x25RouteEntry 10 }
x25RtCallUserData OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The call user data field of the X25 call packet behind the
protocol id. If empty, the call user data field will not
be used for matching."
::= { x25RouteEntry 11 }
x25RtRPOA OBJECT-TYPE
SYNTAX INTEGER (-1..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object will be compared to the first value in the
list of RPOAs in the X25 call packet, if not set to -1."
DEFVAL { -1 }
::= { x25RouteEntry 12 }
x25RtNUI OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object will be compared to the NUI facility supplied
with the call. If this object is an empty string, the
NUI facility will not be used for the matching process."
::= { x25RouteEntry 13 }
x25RtRewritingRule OBJECT-TYPE
SYNTAX INTEGER (0..999999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This Object specifies a rewriting rule in the X25 Rewriting
Rule table. The call packed will be processed according
to this rewriting rule before the call is being delivered.
If this value is set to zero, no rewriting will take
place."
::= { x25RouteEntry 14 }
x25RtMetric OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies a metric similar to the metric of an
IP routing entry. If a call matches multiple entries in the
X25 routing table, the routing entry with the lowest value
of Metric will be used to route the call."
::= { x25RouteEntry 15 }
x25RtCug OBJECT-TYPE
SYNTAX INTEGER (-1..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object will be compared to the CUG facility supplied
with the call, if not set to -1."
DEFVAL { -1 }
::= { x25RouteEntry 16 }
x25RtCugOutgoing OBJECT-TYPE
SYNTAX INTEGER (-1..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object will be compared to the Outgoing CUG facility
supplied with the call, if not set to -1."
DEFVAL { -1 }
::= { x25RouteEntry 17 }
x25RtCugBilateral OBJECT-TYPE
SYNTAX INTEGER (-1..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object will be compared to the Bilateral CUG facility
supplied with the call, if not set to -1."
DEFVAL { -1 }
::= { x25RouteEntry 18 }
x25RtDstLinkAddrRule OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"If x25RtDstLinkAddrMode is set to rule this object describes,
how to develop the destination link address (may be ISDN
call number, MAC address or IP address) from destination X.25
address or destination X.25 NSAP."
::= { x25RouteEntry 19 }
x25RewriteTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25RewriteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This Table contains entries, that describe different
rules of rewriting the call parameters before delivering
a call. Which entry in this table is used, will be determined
by the route table."
::= { x25 6 }
x25RewriteEntry OBJECT-TYPE
SYNTAX X25RewriteEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { x25RwRewritingRule }
::= { x25RewriteTable 1 }
X25RewriteEntry ::=
SEQUENCE {
x25RwRewritingRule INTEGER,
x25RwReverseCharging INTEGER,
x25RwRPOA INTEGER,
x25RwNUI DisplayString,
x25RwSrcAddr DisplayString,
x25RwSrcNSAP DisplayString,
x25RwDstAddr DisplayString,
x25RwDstNSAP DisplayString,
x25RwProtocolId INTEGER,
x25RwCallUserData OCTET STRING,
x25RwRespSrcAddr DisplayString,
x25RwRespSrcNSAP DisplayString,
x25RwRespDstAddr DisplayString,
x25RwRespDstNSAP DisplayString,
x25RwRespProtocolId INTEGER,
x25RwRespCallUserData OCTET STRING,
x25RwCug INTEGER,
x25RwCugOutgoing INTEGER,
x25RwCugBilateral INTEGER
}
x25RwRewritingRule OBJECT-TYPE
SYNTAX INTEGER (1..999999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The unique number of the rewriting rule."
::= { x25RewriteEntry 1 }
x25RwReverseCharging OBJECT-TYPE
SYNTAX INTEGER {
dont-change(1), set(2), clear(3), delete(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes what to do with the reverse charging
facility."
DEFVAL { dont-change }
::= { x25RewriteEntry 2 }
x25RwRPOA OBJECT-TYPE
SYNTAX INTEGER {
dont-change(1), remove-first(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes what to do with the rpoa facility."
DEFVAL { dont-change }
::= { x25RewriteEntry 3 }
x25RwNUI OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the new value of the NUI facility.
If this object is an empty string, the NUI facility
will not be changed."
::= { x25RewriteEntry 4 }
x25RwSrcAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the source address. Digits
will be set directly to the new address. A '.' will
move a digit from the old address to the new address.
A '*' will move all remaining digits from the old address
to the new address. A '%' will delete a digit from the
old address. A '#' will append all digits from the old
address to the new address. Please note that the
eventually leading '@' (indicating extended adressing)
is handled execatly like digits. If this object is empty,
the source address will not be changed."
::= { x25RewriteEntry 5 }
x25RwSrcNSAP OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the source NSAP. Digits
will be set directly to the new NSAP. A '.' will
move a digit from the old NSAP to the new NSAP.
A '*' will move all remaining digits from the old NSAP
to the new NSAP. A '%' will delete a digit from the
old NSAP. A '#' will append all digits from the old
NSAP to the new NSAP. Please note that the eventually
leading '@' (indicating extended adressing) is handled
execatly like digits. If this object is empty, the
source NSAP will not be changed."
::= { x25RewriteEntry 6 }
x25RwDstAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the destination address. Digits
will be set directly to the new address. A '.' will
move a digit from the old address to the new address.
A '*' will move all remaining digits from the old address
to the new address. A '%' will delete a digit from the
old address. A '#' will append all digits from the old
address to the new address. Please note that the
eventually leading '@' (indicating extended adressing) is
handled execatly like digits. If this object is empty,
the destination address will not be changed."
::= { x25RewriteEntry 7 }
x25RwDstNSAP OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the destination NSAP. Digits
will be set directly to the new NSAP. A '.' will
move a digit from the old NSAP to the new NSAP.
A '*' will move all remaining digits from the old NSAP
to the new NSAP. A '%' will delete a digit from the
old NSAP. A '#' will append all digits from the old
NSAP to the new NSAP. Please note that the eventually
leading '@' (indicating extended adressing) is handled
execatly like digits. If this object is empty, the
destination NSAP will not be changed."
::= { x25RewriteEntry 8 }
x25RwProtocolId OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the new value of the protocol id field.
The protocol id field will not be changed, if this object
is set to -1"
DEFVAL { -1 }
::= { x25RewriteEntry 9 }
x25RwCallUserData OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The new value of the call user data field. The call user data
field will not be changed, if this object is an empty string.
A leading '%' will be ignored. This allows to delete the
call user data portion of a call packet by setting this
object to a single '%'."
::= { x25RewriteEntry 10 }
x25RwRespSrcAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the source address of the call
accepted packet. Digits will be set directly to the new
address. A '.' will move a digit from the old address to
the new address. A '*' will move all remaining digits
from the old address to the new address. A '%' will
delete a digit from the old address. A '#' will append
all digits from the old address to the new address. Please
note that the eventually leading '@' (indicating extended
adressing) is handled execatly like digits. If this object
is empty, the source address will not be changed."
::= { x25RewriteEntry 11 }
x25RwRespSrcNSAP OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the source NSAP in the call
accepted packet. Digits will be set directly to the new
NSAP. A '.' will move a digit from the old NSAP to the
new NSAP. A '*' will move all remaining digits from the
old NSAP to the new NSAP. A '%' will delete a digit from the
old NSAP. A '#' will append all digits from the old NSAP
to the new NSAP. Please note that the eventually leading
'@' (indicating extended adressing) is handled execatly like
digits. If this object is empty, the source NSAP will
not be changed."
::= { x25RewriteEntry 12 }
x25RwRespDstAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the destination address of the call
accepted packet. Digits will be set directly to the new
address. A '.' will move a digit from the old address to
the new address. A '*' will move all remaining digits
from the old address to the new address. A '%' will
delete a digit from the old address. A '#' will append
all digits from the old address to the new address. Please
note that the eventually leading '@' (indicating extended
adressing) is handled execatly like digits. If this object
is empty, the destination address will not be changed."
::= { x25RewriteEntry 13 }
x25RwRespDstNSAP OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies how to rewrite the destination NSAP in the call
accepted packet. Digits will be set directly to the new
NSAP. A '.' will move a digit from the old NSAP to the
new NSAP. A '*' will move all remaining digits from the
old NSAP to the new NSAP. A '%' will delete a digit from the
old NSAP. A '#' will append all digits from the old NSAP
to the new . Please note that the eventually leading
'@' (indicating extended adressing) is handled execatly like
digits. If this object is empty, the destination NSAP will
not be changed."
::= { x25RewriteEntry 14 }
x25RwRespProtocolId OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the new value of the ProtocolID field
of the call accepted packet. The ProtocolID will not be
changed, if this object is set to -1."
DEFVAL { -1 }
::= { x25RewriteEntry 15 }
x25RwRespCallUserData OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The new value of the call user data field of the call
accepted packet. The call user data field will not be
changed, if this object is an empty string. A leading
'%' will be ignored. This allows to delete the
call user data portion of a call accepted packet by
setting this object to a single '%'."
::= { x25RewriteEntry 16 }
x25RwCug OBJECT-TYPE
SYNTAX INTEGER (-2..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the new value of the CUG facility.
If this object is set to -1, the CUG facility will not be
changed. The CUG facility will be removed, if this object is
set to -2."
DEFVAL { -1 }
::= { x25RewriteEntry 17 }
x25RwCugOutgoing OBJECT-TYPE
SYNTAX INTEGER (-2..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the new value of the Outgoing CUG
facility. If this object is set to -1, the Outgoing CUG
facility will not be changed. The Outgoing CUG facility will be
removed, if this object is set to -2."
DEFVAL { -1 }
::= { x25RewriteEntry 18 }
x25RwCugBilateral OBJECT-TYPE
SYNTAX INTEGER (-2..9999)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the new value of the Bilateral CUG
facility. If this object is set to -1, the Bilateral CUG
facility will not be changed. The Bilateral CUG facility will
be removed, if this object is set to -2."
DEFVAL { -1 }
::= { x25RewriteEntry 19 }
x25MprTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25MprEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains an entry for each partner reachable
via X.25 for Multiprotocol over X.25 according to RFC 1356.
Entries in this table are created manually and will result
to the creation of a multiprotocol routing interface in
the ifTable. This interface can than be used by higher
level protocols like ip, ipx and bridging.
The object x25MprIfIndex shall be set to 0 for creation
of new entries. The BRICK will allocate the next free
interface index and assign it ti x25MprIfIndex.
Rows of this table can be deleted by setting the object
x25MprEncapsulation to the value delete.
"
::= { x25 7 }
x25MprEntry OBJECT-TYPE
SYNTAX X25MprEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { x25MprIfIndex }
::= { x25MprTable 1 }
X25MprEntry ::=
SEQUENCE {
x25MprIfIndex INTEGER,
x25MprMtu INTEGER,
x25MprEncapsulation INTEGER,
x25MprNumVC INTEGER,
x25MprMaxVC INTEGER,
x25MprWinSize INTEGER,
x25MprPktSize INTEGER,
x25MprShortHold INTEGER,
x25MprMaxRetries INTEGER,
x25MprBlockTime INTEGER,
x25MprAddr DisplayString,
x25MprMode INTEGER,
x25MprAutoRoute INTEGER,
x25MprIpSubnet IpAddress,
x25MprIpSubnetMask IpAddress
}
x25MprIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains an interface index and assigns the
row to an entry in ifTable. When creating new entries
in the table, the value of this object shall be set to 0.
The next free ifIndex value is than allocated
by the BRICK and assigned to the object. At the same
time a new interface is created in the IfTable."
DEFVAL { 0 }
::= { x25MprEntry 1 }
x25MprMtu OBJECT-TYPE
SYNTAX INTEGER (576..8180)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The Maximum transfer unit to be used with the interface,
the row is describing."
DEFVAL { 1500 }
::= { x25MprEntry 2 }
x25MprEncapsulation OBJECT-TYPE
SYNTAX INTEGER {
ip-rfc877(1), ip(2), ipx(3), mpr(4), delete(5)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the encapsulation method to be used.
If this object is set to ip_rfc877, the RFC877 compatible
encapsulation is selected. The relating interface
is only capabable of transferring IP datagrams. All
other protocols are not supported. Virtual channels
are established only with the CUD field set to CC.
If this object is set to ip, the relating interface is
also only capable of forwarding IP datagrams. However,
the virtual channels are setup with the CUD field
set to 80 00 00 00 08 00.
The encapsulation ipx allows only forwarding of IPX
datagrams. VCs are established using a CUD field
of 80 00 00 00 81 37.
If this object is set to mpr, the corresponding
corresponding interface is capable of IP, IPX and
BRIDGING. The different protocols are multiplexed over
the same VC. The CUD field is set to 00."
DEFVAL { ip-rfc877 }
::= { x25MprEntry 3 }
x25MprNumVC OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the number of VCs used with the
corresponding interface. The BRICK will always try to
have that many VCs available for the relating interface."
DEFVAL { 1 }
::= { x25MprEntry 4 }
x25MprMaxVC OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the maximum number of VCs used
with the corresponding interface. It shall be greater
or equal to x25MprNumVC."
DEFVAL { 1 }
::= { x25MprEntry 5 }
x25MprWinSize OBJECT-TYPE
SYNTAX INTEGER (1..7)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the window size to be
used for outgoing X.25 virtual calls."
DEFVAL { 7 }
::= { x25MprEntry 6 }
x25MprPktSize OBJECT-TYPE
SYNTAX INTEGER {
p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the packet size, to be used for
outgoing X.25 calls. Please note that this parameter is
independant of the x25MprMtu parameter."
DEFVAL { p4096 }
::= { x25MprEntry 7 }
x25MprShortHold OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the time of inactivity in seconds,
after which the VCs are disconnected automatically."
DEFVAL { 60 }
::= { x25MprEntry 8 }
x25MprMaxRetries OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the maximum number of tries for
X.25 call establishement. If the BRICK has tried to establish
the call for this many times, the interface is in
the blocked state for a time specified by x25MprBlockTime.
During the blocked state, no more tries are made."
DEFVAL { 5 }
::= { x25MprEntry 9 }
x25MprBlockTime OBJECT-TYPE
SYNTAX INTEGER (0..65536)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the amount of time, the corresponding
interface remains in the blocked state after too many
tries to establish the X.25 call."
DEFVAL { 60 }
::= { x25MprEntry 10 }
x25MprAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The X.25 address to be used with this interface. A leading
@ indicates extended adressing."
::= { x25MprEntry 11 }
x25MprMode OBJECT-TYPE
SYNTAX INTEGER {
normal(1), multiuser(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the operating mode of the interface.
normal -- normal operating mode
multiuser -- A new interface is created for each
incoming X.25 call.
"
DEFVAL { normal }
::= { x25MprEntry 12 }
x25MprAutoRoute OBJECT-TYPE
SYNTAX INTEGER {
off(1), check(2), translate(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes, how automatic routes are created.
It is especially usefull combined with the multiuser Mode
of the interface.
off -- do not create automatic routes
check -- Check the source address of the
the first packet and create a backward
Route, when in the range specified by
IpSubnet/IpSubnetMask
translate -- Translate the ip source address to
the range specified by IpSubnet/IpSubnetMask.
Automatically create ipNatOutEntries
and set ipExtIfNat for dynamic interfaces
to reverse.
"
DEFVAL { off }
::= { x25MprEntry 13 }
x25MprIpSubnet OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies, together with x25MprSubnetMask
the possible range for automatically created routes.
The object is valid, when x25MprMode is set to autoroute
or multiuser.
"
::= { x25MprEntry 14 }
x25MprIpSubnetMask OBJECT-TYPE
SYNTAX IpAddress
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies, together with x25MprSubnet
the possible range for automatically created routes.
The object is valid, when x25MprMode is set to autoroute
or multiuser.
"
::= { x25MprEntry 15 }
-- x25PadProfileTable OBJECT-TYPE ::= { x25 8 }
-- x25ToTcpTable OBJECT-TYPE ::= { x25 9 }
x25LocalPadCall OBJECT-TYPE
SYNTAX INTEGER { accept(1), dont-accept(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies wether a PAD Call (PID=1) routed
to the local X.25 entity (ifIndex=1) should
be accepted to allow for a remote login via X.25. This
may be disabled for security reasons by setting this
object do dont-accept."
DEFVAL { accept }
::= { x25 10 }
x25LocalAddr OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The X.25 address to be used as originating address
for outgoing X.25 call from this BRICK. A leading
@ indicates extended adressing."
DEFVAL { "" }
::= { x25 11 }
x25Rerouting OBJECT-TYPE
SYNTAX INTEGER { allow(1), disallow(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies whether a rerouting request should be
accepted to establish connection to another server.
This is only relevant for x29 rerouting."
DEFVAL { disallow }
::= { x25 12 }
x25HistoryMaxEntries OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Maximum number of x25CallHistory entries in memory."
DEFVAL { 10 }
::= { x25 13 }
x25AccountingTemplate OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Specifies the format of accounting messages sent by the
syslog protocol. The format can consist of any order of
the following variables.
Tag Meaning
%S Date and Time the connection was established;
in DD.MM.YY/HH:MM:SS format.
%d The duration of the connection in seconds.
%z The X25 source address.
%Z The X25 destination address.
%y Total number of bytes received over the connection.
%Y Total number of bytes sent over the connection.
%g Total packets received over the connection.
%G Total packets sent over the connection.
%c The X25 clear cause.
%C The X25 clear diagnostic.
%f The source interface.
%F The destination interface.
%v The source virtual channel number.
%V The destination virtual channel number.
The default accounting template setting contains the
following tags: %S,%d,%z,%Z,%y,%Y,%g,%G,%c,%C."
DEFVAL { "%S,%d,%z,%Z,%y,%Y,%g,%G,%c,%C" }
::= { x25 14 }
x25OverIsdnIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF X25OverIsdnIfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains an entry for each Interface
accessible to the X.25 Switch for X.25 over ISDN
B-channel data transfer. This mechanism superseeds
the old one using the PPP implementation as ISDN
call generator. The relationship to ISDN is much more
direct and offers more possibilities.
For each entry in this table, there is a corresponding
Table in the ifTable of mib-2.
"
::= { x25 15 }
x25OverIsdnIfEntry OBJECT-TYPE
SYNTAX X25OverIsdnIfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
""
INDEX { xoiIfIndex }
::= { x25OverIsdnIfTable 1 }
X25OverIsdnIfEntry ::=
SEQUENCE {
xoiIfIndex INTEGER,
xoiIfType INTEGER,
xoiIfDirection INTEGER,
xoiIfLocalNumber DisplayString,
xoiIfRemoteNumber DisplayString,
xoiIfStkMask BitValue,
xoiIfSignalling HexValue,
xoiIfL1Protocol INTEGER,
xoiIfL2Protocol INTEGER,
xoiIfPadProfile INTEGER,
xoiIfModemProfile INTEGER,
xoiIfMaxCalls INTEGER,
xoiIfL2Mode INTEGER,
xoiIfStatCommand INTEGER,
xoiIfMaxRetries INTEGER,
xoiIfRetryTime INTEGER,
xoiIfBlockTime INTEGER,
-- Statistics
xoiIfCurrentCalls INTEGER,
xoiIfIncomingCalls INTEGER,
xoiIfOutgoingCalls INTEGER,
xoiIfMaxConcCalls INTEGER,
xoiIfCumulTime INTEGER,
xoiIfBrkSeqVar INTEGER
}
xoiIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object contains the interface index for the
interface. When this object is set to an interface
number, that does not yet correspond to an existing
interface, a new interface is created. The interface
index is forced into the range of indices for X25 over
ISDN routing. Setting this object to an existing interface
index sets all the values for the respective row to
default values.
"
::= { x25OverIsdnIfEntry 1 }
xoiIfType OBJECT-TYPE
SYNTAX INTEGER { delete(1), one-to-one(2), multi-vc(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the type of the interface and can
also be used to delete the complete row and the corresponding
interface. The following types are available:
one-to-one Each X.25 Call sent to the interface will
create a new isdn call. This leads to
a one-to-one relation between ISDN and
X.25 calls.
multi-vc The first X.25 call sent to the interface
will create a new isdn call established. The
following calls will be sent to the same ISDN
call as long as VCs (two way or outgoing)
are available. Only if all VCs are used up,
a new ISDN call will be established.
In either case, multiple incoming X.25 calls are allowed
according to the X25LinkPresetTable. The ISDN calls
are cleared, as soon as the corresponding layer 2 Link
has been cleared as specified in x25LkL2IdleTimer.
"
DEFVAL { one-to-one }
::= { x25OverIsdnIfEntry 2 }
xoiIfDirection OBJECT-TYPE
SYNTAX INTEGER { in(1), out(2), both(3), none(4) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the allowd direction of ISDN calls.
The value none can be used to disable an interface.
"
DEFVAL { both }
::= { x25OverIsdnIfEntry 3 }
xoiIfLocalNumber OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the local ISDN number.
For outgoing calls, it is used as calling party number,
unless it is overwritten by the X.25 routing mechanisms.
For incoming calls it is used to assign the incoming call
to an interface. The called party number of the incoming
ISDN call is matched against the value of this object.
Wildcards are allowed in this case.
Use care, when IfDirection is set to both. No Wildcards
are allowed for outgoing calls.
"
::= { x25OverIsdnIfEntry 4 }
xoiIfRemoteNumber OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the remote ISDN number.
For outgoing ISDN calls, it is used as called party number,
unless it is overwritten by X.25 routing mechanisms.
For incoming calls it is used to assign the incoming call
to an interface. The calling party number of the incoming
ISDN call is matched against the value of this object.
Wildcards are allowed in this case.
Use care, when IfDirection is set to both. No Wildcards
are allowed for outgoing calls.
"
::= { x25OverIsdnIfEntry 5 }
xoiIfStkMask OBJECT-TYPE
SYNTAX BitValue
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the ISDN stacks to be used for incoming
and outgoing ISDN calls. If none of the specified stacks is
ready for use, the ifOperStatus in the corresponding entry
of the ifTable is set to down.
"
-- DEFVAL { 'FFFFFFFF'H }
DEFVAL { 4294967295 }
::= { x25OverIsdnIfEntry 6 }
xoiIfSignalling OBJECT-TYPE
SYNTAX HexValue
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object sets the signalling for outgoing calls and is used
assign incoming calls to interfaces. If set to 0, an ISDN
signalling is generated automatically for outgoing calls
depending on the values of L1Protocol and L2Protocol. All
incoming calls are routed to the interface, when this object
is set to 0.
Other values are directly used for outgoing calls,
independantly of the setting of L1Protocol and L2Protocol.
Incoming calls are only assigned to the interface, when
the signalling is equal to the value specified here.
The possible values are specified elsewhere.
"
::= { x25OverIsdnIfEntry 7 }
xoiIfL1Protocol OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
hdlc-64k(2),
hdlc-56k(3),
v110-1200(13),
v110-2400(14),
v110-4800(15),
v110-7200(16),
v110-9600(17),
v110-14400(18),
v110-19200(19),
v110-28800(20),
v110-38400(21),
v120-64k(31),
v120-56k(32),
modem(41)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the layer 1 protocol for the interface.
The specified mode is used for incoming and outgoing calls.
If auto is selected, the layer 1 protocol will be derived from
ISDN signalling for incoming calls. For outgoing calls,
layer1 mode will be derived from layer 2 protocol.
"
DEFVAL { auto }
::= { x25OverIsdnIfEntry 8 }
xoiIfL2Protocol OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
lapb(2),
pad(3),
padoverlapb(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the layer 2 protocol of the interface.
The setting applies to incoming and outgoing calls.
When auto is selected, the layer 2 protocol is derived from
the signalling of the call for incoming calls. For outgoing
calls, usually lapb is used.
"
DEFVAL { auto }
::= { x25OverIsdnIfEntry 9 }
xoiIfPadProfile OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"In case of a PAD instance being used (see Layer2Mode), this
object specifies the PAD profile to be used.
"
::= { x25OverIsdnIfEntry 10 }
xoiIfModemProfile OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"In case of a modem being used for layer 1, this object specifies
the modem profile.
"
::= { x25OverIsdnIfEntry 11 }
xoiIfMaxCalls OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the maximum number of calls for the
interface.
"
DEFVAL { 10 }
::= { x25OverIsdnIfEntry 12 }
xoiIfL2Mode OBJECT-TYPE
SYNTAX INTEGER { auto(1), dte(2), dce(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies whether the layer2 should act in
DTE or DCE configuration. If set to auto. The ISDN caller
is always DTE, and the callee is DCE.
"
DEFVAL { auto }
::= { x25OverIsdnIfEntry 13 }
xoiIfStatCommand OBJECT-TYPE
SYNTAX INTEGER { nop(1), clear(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object may be used, to clear the statistics counters
for the interface. When set to clear, all statistics counters
in this table and the ifTable are set to 0.
"
DEFVAL { nop }
::= { x25OverIsdnIfEntry 14 }
xoiIfMaxRetries OBJECT-TYPE
SYNTAX INTEGER (0..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the number of times, an unsuccessful
call has to be retried. When even after this many times,
it was not possible, to establish an ISDN connection, the
original X.25 call is cleared. In addition to that, when
there are currently no other ISDN calls established for
the interface, the interface moves to the BLOCKED state for
BlockTime seconds.
"
DEFVAL { 0 }
::= { x25OverIsdnIfEntry 15 }
xoiIfRetryTime OBJECT-TYPE
SYNTAX INTEGER (-3600..3600)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the amount of time in seconds, to
wait between the retries of an ISDN call. If the value is
negative, a random time will be chosen between 0 and the
the absolute value.
"
DEFVAL { 0 }
::= { x25OverIsdnIfEntry 16 }
xoiIfBlockTime OBJECT-TYPE
SYNTAX INTEGER (0..3600)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the amount of time in seconds, the
interface will stay in the BLOCKED state after unsuccessful
ISDN call establishment.
"
DEFVAL { 0 }
::= { x25OverIsdnIfEntry 17 }
xoiIfCurrentCalls OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object indicates the number of currently established
calls for the interface.
"
::= { x25OverIsdnIfEntry 20 }
xoiIfIncomingCalls OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object is a statistics counter. It counts the number of
incoming calls for the interface.
"
::= { x25OverIsdnIfEntry 21 }
xoiIfOutgoingCalls OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object is a statistics counter. It counts the number of
outgoing calls for the interface.
"
::= { x25OverIsdnIfEntry 22 }
xoiIfMaxConcCalls OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object is a statistics counter. It indicates the maximum
number of calls being active concurrently.
"
::= { x25OverIsdnIfEntry 23 }
xoiIfCumulTime OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object is a statistics counter. It cumulates the connection
time of all calls assigned to the interface.
"
::= { x25OverIsdnIfEntry 24 }
xoiIfBrkSeqVar OBJECT-TYPE
SYNTAX INTEGER (-10..10)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object indicates the additional number of startbits to detect
a break sequence send from V.110 terminal over an S2M interface.
The default number of startbits is 22, you can vary this value
in range from 12 to 32, configuring here -10 to 10.
"
::= { x25OverIsdnIfEntry 25 }
END
View Git Blame Copy Permalink