WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/bintec/BIANCA-BRICK-HDSL2SHDSL2-MIB

2514 lines
97 KiB
Plaintext
Raw Permalink Blame History

-- This file is corresponding to Release 9.1.10.101 from 2014/08/11 00:00:00
-- $RCSfile: mibhdsl2shdsl2,v $
-- $Revision: 1.19 $
-- (C)opyright 2002-2014 bintec elmeg GmbH, All Rights Reserved
BIANCA-BRICK-HDSL2SHDSL2-MIB DEFINITIONS ::= BEGIN
IMPORTS
Counter, enterprises
FROM RFC1155-SMI
DisplayString
FROM RFC1158-MIB
TRAP-TYPE
FROM RFC-1215
OBJECT-TYPE
FROM RFC-1212;
bintec OBJECT IDENTIFIER ::= { enterprises 272 }
bibo OBJECT IDENTIFIER ::= { bintec 4 }
hdsl2shdsl OBJECT IDENTIFIER
::= { bibo 35 }
-- hdsl2shdsl Group
-- hdsl2shdsl
-- DESCRIPTION
-- "This MIB module defines a collection of objects for managing
-- HDSL2/SHDSL lines. An agent may reside at either end of the
-- line, however the MIB is designed to require no management
-- communication between the modems beyond that inherent in the
-- low-level EOC line protocol as defined in ANSI T1E1.4/2000-006
-- (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)."
-- REVISION "200205090000Z" - May 9, 2002
-- DESCRIPTION "Initial version, published as RFC 3276."
hdsl2ShdslLineMib OBJECT IDENTIFIER ::= { hdsl2shdsl 1 }
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslLineMib 1 }
-- Span Configuration Group
--
-- hdsl2ShdslSpanConfTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "This table supports overall configuration of HDSL2/SHDSL
-- Spans. Entries in this table MUST be maintained in a
-- persistent manner. Entries in this table are created by the
-- system only."
-- ::= { hdsl2ShdslMibObjects 1 }
--
--
-- hdsl2ShdslSpanConfEntry OBJECT-TYPE
-- SYNTAX Hdsl2ShdslSpanConfEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- bintec NODEL
-- DESCRIPTION
-- "An entry in the hdsl2ShdslSpanConfTable. Each entry
-- represents the complete Span in a single HDSL2/SHDSL line.
-- It is indexed by the ifIndex of the associated HDSL2/SHDSL
-- line."
-- INDEX { hdsl2ShdslSpanLineIfIndex }
-- ::= { hdsl2ShdslSpanConfTable 1 }
--
-- Hdsl2ShdslSpanConfEntry ::= SEQUENCE {
-- hdsl2ShdslSpanLineIfIndex INTEGER,
-- hdsl2ShdslSpanNumRepeaters INTEGER,
-- hdsl2ShdslSpanProfile DisplayString,
-- hdsl2ShdslSpanAlarmProfile DisplayString
-- }
--
-- hdsl2ShdslSpanLineIfIndex OBJECT-TYPE
-- SYNTAX INTEGER
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "This object specifies the associated interface index of
-- this HDSL2/SHDSL line."
-- ::= { hdsl2ShdslSpanConfEntry 1 }
--
-- hdsl2ShdslSpanNumRepeaters OBJECT-TYPE
-- SYNTAX INTEGER (0..8)
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object provisions the number of repeaters/regenerators
-- in this HDSL2/SHDSL Span."
-- ::= { hdsl2ShdslSpanConfEntry 2 }
--
-- hdsl2ShdslSpanProfile OBJECT-TYPE
-- SYNTAX DisplayString (SIZE(0..32))
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object is a pointer to a span configuration profile in
-- the hdsl2ShdslSpanConfProfileTable, which applies to this span.
-- The value of this object is the index of the referenced profile
-- in the hdsl2ShdslSpanConfProfileTable. Note that span
-- configuration profiles are only applicable to SHDSL lines.
--
-- HDSL2 lines MUST reference the default profile, 'DEFVAL'.
-- By default, this object will have the value 'DEFVAL' (the index
-- of the default profile).
--
-- Any attempt to set this object to a value that is not the value
-- of the index for an active entry in the profile table,
-- hdsl2ShdslSpanConfProfileTable, MUST be rejected."
-- ::= { hdsl2ShdslSpanConfEntry 3 }
--
-- hdsl2ShdslSpanAlarmProfile OBJECT-TYPE
-- SYNTAX DisplayString (SIZE(0..32))
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object is a pointer to an Alarm configuration profile in
-- the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this
-- object is the index of the referenced profile in the
-- hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold
-- configuration in the referenced profile will be used by default
-- for all segment endpoints in this span. Individual endpoints
-- may override this profile by explicitly specifying some other
-- profile in the hdsl2ShdslEndpointConfTable. By default, this
-- object will have the value 'DEFVAL' (the index of the default
-- profile).
--
-- Any attempt to set this object to a value that is not the value
-- of the index for an active entry in the profile table,
-- hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
-- ::= { hdsl2ShdslSpanConfEntry 4 }
-- Span Status Group
--
-- hdsl2ShdslSpanStatusTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "This table provides overall status information of
-- HDSL2/SHDSL spans. This table contains live data from
-- equipment. As such, it is NOT persistent."
-- ::= { hdsl2ShdslMibObjects 2 }
--
-- hdsl2ShdslSpanStatusEntry OBJECT-TYPE
-- SYNTAX Hdsl2ShdslSpanStatusEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "An entry in the hdsl2ShdslSpanStatusTable. Each entry
-- represents the complete span in a single HDSL2/SHDSL line.
-- It is indexed by the ifIndex of the associated HDSL2/SHDSL
-- line."
-- INDEX { hdsl2ShdslSpanStatusIfIndex }
-- ::= { hdsl2ShdslSpanStatusTable 1 }
--
-- Hdsl2ShdslSpanStatusEntry ::= SEQUENCE {
-- hdsl2ShdslSpanStatusIfIndex INTEGER,
-- hdsl2ShdslSpanStatusNumAvailRepeaters INTEGER,
-- hdsl2ShdslSpanStatusMaxAttainableLineRate INTEGER,
-- hdsl2ShdslSpanStatusActualLineRate INTEGER,
-- hdsl2ShdslSpanStatusTransmissionModeCurrent INTEGER
--
-- }
--
-- hdsl2ShdslSpanStatusIfIndex OBJECT-TYPE
-- SYNTAX INTEGER
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "This object specifies the associated interface index of
-- this HDSL2/SHDSL line."
-- ::= { hdsl2ShdslSpanStatusEntry 1 }
--
-- hdsl2ShdslSpanStatusNumAvailRepeaters OBJECT-TYPE
-- SYNTAX INTEGER (0..8)
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Contains the actual number of repeaters/regenerators
-- discovered in this HDSL2/SHDSL span."
-- ::= { hdsl2ShdslSpanStatusEntry 2 }
--
-- not supported by GlobeSpan !
--
-- hdsl2ShdslSpanStatusMaxAttainableLineRate OBJECT-TYPE
-- SYNTAX INTEGER (0..4112000)
-- ACCESS read-only
-- STATUS mandatory
-- DESCRIPTION
-- "Contains the maximum attainable line rate (bits per second)
-- in this HDSL2/SHDSL span. This object provides the maximum
-- rate the line is capable of achieving. This is based upon
-- measurements made during line probing."
-- ::= { hdsl2ShdslSpanStatusEntry 3 }
--
-- hdsl2ShdslSpanStatusActualLineRate OBJECT-TYPE
-- SYNTAX INTEGER (0..22784000)
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Contains the actual line rate (bits per second) in this
-- HDSL2/SHDSL span. This should equal ifSpeed."
-- ::= { hdsl2ShdslSpanStatusEntry 4 }
--
-- hdsl2ShdslSpanStatusTransmissionModeCurrent OBJECT-TYPE
-- SYNTAX INTEGER {
-- region1(1),
-- region2(2)
-- }
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Contains the current Power Spectral Density (PSD) regional
-- setting of the HDSL2/SHDSL span:
-- region1 - ITU-T G.991.2 Annex A
-- region2 - ITU-T G.991.2 Annex B"
-- ::= { hdsl2ShdslSpanStatusEntry 5 }
-- Unit Inventory Group
--
hdsl2ShdslInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table supports retrieval of unit inventory information
available via the EOC from units in a HDSL2/SHDSL line.
Entries in this table are dynamically created during the
line discovery process. The life cycle for these entries
is as follows:
- xtu discovers a device, either a far-end xtu or an xru
- an inventory table entry is created for the device
- the line goes down for whatever reason
- inventory table entries for unreachable devices are
destroyed.
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line."
INDEX { hdsl2ShdslInvIfIndex }
::= { hdsl2ShdslInventoryTable 1 }
Hdsl2ShdslInventoryEntry ::= SEQUENCE {
hdsl2ShdslInvIfIndex INTEGER,
hdsl2ShdslInvIndex INTEGER,
hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion INTEGER,
hdsl2ShdslInvStandardVersion INTEGER,
hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING,
hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
hdsl2ShdslInvEquipmentCode OCTET STRING,
hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability INTEGER
}
hdsl2ShdslInvIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object specifies the associated interface index of
this HDSL2/SHDSL line."
::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX INTEGER {
xtuC(1),
xtuR(2),
xru1(3),
xru2(4),
xru3(5),
xru4(6),
xru5(7),
xru6(8),
xru7(9),
xru8(10)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Each entry in this table corresponds to a physical element
in a HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Vendor ID as reported in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(12))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Vendor model number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(12))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Vendor serial number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Vendor EOC version as reported in a Discovery Response
message."
::= { hdsl2ShdslInventoryEntry 6 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 7 }
hdsl2ShdslInvVendorListNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(3))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Vendor list number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(2))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Vendor issue number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(6))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Vendor software version as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(10))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."
::= { hdsl2ShdslInventoryEntry 11 }
hdsl2ShdslInvVendorOther OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(12))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Other vendor information as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 12 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX INTEGER {
region1(1),
region2(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit:
region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex B"
::= { hdsl2ShdslInventoryEntry 13 }
-- Segment Endpoint Configuration Group
--
hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner.
Entries in this table are created by the system only."
::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line."
INDEX { hdsl2ShdslEndpointConfIfIndex }
::= { hdsl2ShdslEndpointConfTable 1 }
Hdsl2ShdslEndpointConfEntry ::= SEQUENCE {
hdsl2ShdslEndpointConfIfIndex INTEGER,
hdsl2ShdslEndpointConfSide INTEGER,
-- hdsl2ShdslEndpointConfWirePair INTEGER,
-- hdsl2ShdslEndpointConfAlarmProfile DisplayString,
hdsl2ShdslEndpointConfWireInterface INTEGER,
hdsl2ShdslEndpointConfMinLineRate INTEGER,
hdsl2ShdslEndpointConfMaxLineRate INTEGER,
hdsl2ShdslEndpointConfTransmissionMode INTEGER,
hdsl2ShdslEndpointConfWorstCaseTargetMarginDown INTEGER,
hdsl2ShdslEndpointConfWorstCaseTargetMarginUp INTEGER,
hdsl2ShdslEndpointConfGroupId INTEGER,
hdsl2ShdslEndpointConfLineProbeEnable INTEGER,
hdsl2ShdslEndpointConfLicenseUsage INTEGER,
hdsl2ShdslEndpointConfPamMode INTEGER,
hdsl2ShdslEndpointConfTotalMinLineRate INTEGER,
hdsl2ShdslEndpointConfMinWirePairs INTEGER,
hdsl2ShdslEndpointConfCapListStyle INTEGER
}
hdsl2ShdslEndpointConfIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object specifies the associated interface index of
this HDSL2/SHDSL line."
::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointConfSide OBJECT-TYPE
SYNTAX INTEGER {
networkSide(1),
customerSide(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide textual
convention."
DEFVAL { customerSide }
::= { hdsl2ShdslEndpointConfEntry 2 }
-- hdsl2ShdslEndpointConfWirePair OBJECT-TYPE
-- SYNTAX INTEGER {
-- wirePair1(1),
-- wirePair2(2)
-- }
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "The wire-pair of the modem associated with this segment
-- endpoint as per the Hdsl2ShdslWirePair textual convention."
-- ::= { hdsl2ShdslEndpointConfEntry 3 }
--
-- hdsl2ShdslEndpointConfAlarmProfile OBJECT-TYPE
-- SYNTAX DisplayString (SIZE(0..32))
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the alarm threshold values to be used
-- for this segment endpoint. The values are obtained from the
-- alarm configuration profile referenced by this object. The
-- value of this object is the index of the referenced profile in
-- the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero-
-- length DisplayString). If the value is a zero-length
-- DisplayString, the endpoint uses the default Alarm
-- Configuration Profile for the associated span as per the
-- hdsl2ShdslSpanConfAlarmProfile object in the
-- hdsl2ShdslSpanConfTable. The default value of this object is
-- a zero-length DisplayString.
--
-- Any attempt to set this object to a value that is not the value
-- of the index for an active entry in the profile table,
-- hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
-- ::= { hdsl2ShdslEndpointConfEntry 4 }
--
hdsl2ShdslEndpointConfWireInterface OBJECT-TYPE
SYNTAX INTEGER {
twoWire(1),
fourWire(2),
fourWireStandard(3),
fourWireIMA(4),
sixWire(5),
sixWireIMA(6),
eightWire(7),
eightWireIMA(8),
not-used(9),
groupMember(10),
twoWireEFM(11),
fourWireEFM(12),
sixWireEFM(13),
eightWireEFM(14)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the bonding mode of
the SHDSL Line.
twoWire(1) : no bonding is used
fourWire(2) : four-wire mode
fourWireStandard(3) : four-wire mode, disable globespan enhanced mode
fourWireIMA(4) : 2 wire pairs bonded with IMA
sixWire(5) : 3 wire pairs in m-pair mode
sixWireIMA(6) : 3 wire pairs bonded with IMA
eightWire(7) : 4 wire pairs in m-pair mode
eightWireIMA(8) : 4 wire pairs bonded with IMA
not-used(9) : wire pair inactive
groupMember(10) : wire pair belongs to a bonding group
twoWireEFM(11) : 2 wire EFM mode
fourWireEFM(12) : 2 wire pairs in EFM mode with PAF bonding
sixWireEFM(13) : 3 wire pairs in EFM mode with PAF bonding
eightWireEFM(14) : 4 wire pairs in EFM mode with PAF bonding"
DEFVAL { twoWire }
::= { hdsl2ShdslEndpointConfEntry 5 }
hdsl2ShdslEndpointConfMinLineRate OBJECT-TYPE
SYNTAX INTEGER (0..22784000)
-- UNITS "bps"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslEndpointConfEntry 6 }
hdsl2ShdslEndpointConfMaxLineRate OBJECT-TYPE
SYNTAX INTEGER (0..22784000)
-- UNITS "bps"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslEndpointConfEntry 7 }
hdsl2ShdslEndpointConfTransmissionMode OBJECT-TYPE
SYNTAX INTEGER {
region1(1),
region2(2),
region1or2(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line:
region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex B"
DEFVAL { region1 }
::= { hdsl2ShdslEndpointConfEntry 8 }
hdsl2ShdslEndpointConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX INTEGER (0..65535)
-- UNITS "dB"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointConfEntry 11 }
hdsl2ShdslEndpointConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX INTEGER (-10..21)
-- UNITS "dB"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointConfEntry 13 }
hdsl2ShdslEndpointConfGroupId OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object defines which wire-pairs belong to the same
M-pair group or IMA group. Members of the same group have
the same entry."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointConfEntry 14 }
hdsl2ShdslEndpointConfLineProbeEnable OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
disable(2),
enable(3),
enable-std(4)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the configuration of the PMMS
behavior:
auto - Line Probe is enabled if hdsl2ShdslEndpointConfMinLineRate
< hdsl2ShdslEndpointConfMaxLineRate.
disable - Line Probe is disabled.
enable - Line Probe is enabled.
enable_std - Line Probe is enabled and standard
compliant behaviour is enforced."
DEFVAL { auto }
::= { hdsl2ShdslEndpointConfEntry 15 }
hdsl2ShdslEndpointConfLicenseUsage OBJECT-TYPE
SYNTAX INTEGER {
none(1),
missing(2),
shdsl(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Shows which license type is currently used for this
SHDSL interface."
DEFVAL { none }
::= { hdsl2ShdslEndpointConfEntry 16 }
hdsl2ShdslEndpointConfPamMode OBJECT-TYPE
SYNTAX INTEGER (4..252)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies which modulation modes are allowed
for this wire pair.
16 - 16-TCPAM, used for Annex A,B and F,G.
32 - 32-TCPAM, used for Annex F,G only.
4, 8, 64, 128 - non standard proprietary modes.
On CPE site more than one mode can be allowed by adding
the values.
On CO site only the highest mode is used if several
values are added."
DEFVAL { 48 }
::= { hdsl2ShdslEndpointConfEntry 17 }
hdsl2ShdslEndpointConfTotalMinLineRate OBJECT-TYPE
SYNTAX INTEGER (1..50000000)
-- UNITS "bps"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the minimum transmission rate
in bits-per-second (bps) for the associated SHDSL bundle.
The associated interfaces go up only when the sum of the
data rates of the associated wire pairs in state Showtime
reaches or exceeds the specified value.
This variable has no effect with single pair modes."
DEFVAL { 1 }
::= { hdsl2ShdslEndpointConfEntry 18 }
hdsl2ShdslEndpointConfMinWirePairs OBJECT-TYPE
SYNTAX INTEGER (1..4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the minimum number of wire pairs
for the associated SHDSL bundle. The associated interfaces
go up only when at least the specified number of wire pairs
is connected and in Showtime.
This variable has no effect with single pair modes."
DEFVAL { 1 }
::= { hdsl2ShdslEndpointConfEntry 19 }
hdsl2ShdslEndpointConfCapListStyle OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
old(2),
new(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the data format of the capability list,
that is exchanged during the G.994.1 handshake:
auto - automatic detection of the used capability list style.
old - only ATM modes till 2312 kbps can be negotiated.
new - all modes can be negotiated."
DEFVAL { auto }
::= { hdsl2ShdslEndpointConfEntry 20 }
-- Segment Endpoint Current Status/Performance Group
--
hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner. Entries in this
table are created by the system only."
::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line."
INDEX { hdsl2ShdslEndpointCurrIfIndex }
::= { hdsl2ShdslEndpointCurrTable 1 }
Hdsl2ShdslEndpointCurrEntry ::= SEQUENCE {
hdsl2ShdslEndpointCurrIfIndex INTEGER,
hdsl2ShdslEndpointCurrReceivedBlks INTEGER,
hdsl2ShdslEndpointCurrTransmittedBlks INTEGER,
hdsl2ShdslEndpointCurrCorrectedBlks INTEGER,
hdsl2ShdslEndpointCurrUncorrectBlks INTEGER,
hdsl2ShdslEndpointCurrAtn INTEGER,
hdsl2ShdslEndpointCurrSnrMgn INTEGER,
hdsl2ShdslEndpointCurrStatus INTEGER,
hdsl2ShdslEndpointES Counter,
hdsl2ShdslEndpointSES Counter,
hdsl2ShdslEndpointCRCanomalies Counter,
hdsl2ShdslEndpointLOSWS Counter,
hdsl2ShdslEndpointUAS Counter,
hdsl2ShdslEndpointCurr15MinReceivedBlks INTEGER,
hdsl2ShdslEndpointCurr15MinTransmittedBlks INTEGER,
hdsl2ShdslEndpointCurr15MinCorrectedBlks INTEGER,
hdsl2ShdslEndpointCurr15MinUncorrectBlks INTEGER,
hdsl2ShdslEndpointCurr15MinTimeElapsed INTEGER,
hdsl2ShdslEndpointCurr15MinES INTEGER,
hdsl2ShdslEndpointCurr15MinSES INTEGER,
hdsl2ShdslEndpointCurr15MinCRCanomalies INTEGER,
hdsl2ShdslEndpointCurr15MinLOSWS INTEGER,
hdsl2ShdslEndpointCurr15MinUAS INTEGER,
hdsl2ShdslEndpointCurr1DayReceivedBlks INTEGER,
hdsl2ShdslEndpointCurr1DayTransmittedBlks INTEGER,
hdsl2ShdslEndpointCurr1DayCorrectedBlks INTEGER,
hdsl2ShdslEndpointCurr1DayUncorrectBlks INTEGER,
hdsl2ShdslEndpointCurr1DayTimeElapsed INTEGER,
hdsl2ShdslEndpointCurr1DayES INTEGER,
hdsl2ShdslEndpointCurr1DaySES INTEGER,
hdsl2ShdslEndpointCurr1DayCRCanomalies INTEGER,
hdsl2ShdslEndpointCurr1DayLOSWS INTEGER,
hdsl2ShdslEndpointCurr1DayUAS INTEGER
}
hdsl2ShdslEndpointCurrIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object specifies the associated interface index of
this HDSL2/SHDSL line."
::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrReceivedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all encoded blocks received on this channel
since agent reset."
::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrTransmittedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all encoded blocks transmitted on this channel
since agent reset."
::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointCurrCorrectedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all blocks received with errors that were
corrected since agent reset. These blocks are passed
on as good data."
::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointCurrUncorrectBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all blocks received with uncorrectable errors
since agent reset."
::= { hdsl2ShdslEndpointCurrEntry 5 }
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX INTEGER (-127..128)
-- UNITS "dB"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX INTEGER (-127..128)
-- UNITS "dB"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX INTEGER {
noDefect(1),
powerBackoff(2),
deviceFault(3),
dcContinuityFault(4),
snrMarginAlarm(5),
-- loopAttenuationAlarm(6),
loswFailureAlarm(7),
configInitFailure(8),
protocolInitFailure(9),
noNeighborPresent(10),
loopbackActive(11)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Contains the current state of the endpoint. This is a
bitmap of possible conditions. The various bit positions
are:
noDefect There no defects on the line.
powerBackoff Indicates enhanced Power Backoff.
deviceFault Indicates a vendor-dependent
diagnostic or self-test fault
has been detected.
dcContinuityFault Indicates vendor-dependent
conditions that interfere with
span powering such as short and
open circuits.
snrMarginAlarm Indicates that the SNR margin
has dropped below the alarm threshold.
loopAttenuationAlarm Indicates that the loop attenuation
exceeds the alarm threshold.
(not supported by GlobeSpan !)
loswFailureAlarm Indicates a forward LOSW alarm.
configInitFailure Endpoint failure during initialization
due to paired endpoint not able to
support requested configuration.
protocolInitFailure Endpoint failure during initialization
due to incompatible protocol used by
the paired endpoint.
noNeighborPresent Endpoint failure during initialization
due to no activation sequence detected
from paired endpoint.
loopbackActive A loopback is currently active at this
Segment Endpoint.
This is intended to supplement ifOperStatus. Note that there
is a 1-1 relationship between the status bits defined in this
object and the notification thresholds defined elsewhere in
this MIB."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter
-- UNITS "detected CRC Anomalies"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was
last restarted."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 12 }
hdsl2ShdslEndpointUAS OBJECT-TYPE
SYNTAX Counter
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinReceivedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all encoded blocks received on this channel
within the mandatory 15 minute interval."
::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr15MinTransmittedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all encoded blocks transmitted on this channel
within the mandatory 15 minute interval."
::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr15MinCorrectedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all blocks received with errors that were
corrected on this channel within the mandatory 15 minute
interval."
::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr15MinUncorrectBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all blocks received with uncorrectable errors
on this channel within the mandatory 15 minute interval."
::= { hdsl2ShdslEndpointCurrEntry 17 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX INTEGER (0..86399)
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute
interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Severely Errored Seconds (SES) in the current
15-minute interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 }
hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "detected CRC Anomalies"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of CRC anomalies in the current 15-minute interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 21 }
hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 22 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 23 }
hdsl2ShdslEndpointCurr1DayReceivedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all encoded blocks received on this channel
during the mandatory day as measured by
hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 24 }
hdsl2ShdslEndpointCurr1DayTransmittedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all encoded blocks transmitted on this channel
during the mandatory day as measured by
hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 25 }
hdsl2ShdslEndpointCurr1DayCorrectedBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all blocks received with errors that were
corrected on this channel during the mandatory day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 26 }
hdsl2ShdslEndpointCurr1DayUncorrectBlks OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of all blocks received with uncorrectable errors
on this channel during the mandatory day as measured by
hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 27 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX INTEGER (0..86399)
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Number of seconds that have elapsed since the beginning of
the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 28 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 29 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 30 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "detected CRC Anomalies"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 31 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 32 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX INTEGER
-- UNITS "seconds"
ACCESS read-only
STATUS mandatory
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 33 }
-- Segment Endpoint 15-Minute Interval Status/Performance Group
--
-- hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "This table provides one row for each HDSL2/SHDSL endpoint
-- performance data collection interval. This table contains
-- live data from equipment. As such, it is NOT persistent.
-- Entries in this table are created by the system only."
-- ::= { hdsl2ShdslMibObjects 6 }
--
-- hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
-- SYNTAX Hdsl2Shdsl15MinIntervalEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "An entry in the hdsl2Shdsl15MinIntervalTable."
-- INDEX { hdsl2Shdsl15MinIntervalIfIndex }
-- ::= { hdsl2Shdsl15MinIntervalTable 1 }
--
-- Hdsl2Shdsl15MinIntervalEntry ::= SEQUENCE {
-- hdsl2Shdsl15MinIntervalIfIndex INTEGER,
-- hdsl2Shdsl15MinIntervalNumber INTEGER,
-- hdsl2Shdsl15MinIntervalES INTEGER,
-- hdsl2Shdsl15MinIntervalSES INTEGER,
-- hdsl2Shdsl15MinIntervalCRCanomalies INTEGER,
-- hdsl2Shdsl15MinIntervalLOSWS INTEGER,
-- hdsl2Shdsl15MinIntervalUAS INTEGER
-- }
--
-- hdsl2Shdsl15MinIntervalIfIndex OBJECT-TYPE
-- SYNTAX INTEGER
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "This object specifies the associated interface index of
-- this HDSL2/SHDSL line."
-- ::= { hdsl2Shdsl15MinIntervalEntry 1 }
--
-- hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
-- SYNTAX INTEGER (1..96)
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Performance Data Interval number. 1 is the the most recent
-- previous interval; interval 96 is 24 hours ago. Intervals
-- 2..96 are optional."
-- ::= { hdsl2Shdsl15MinIntervalEntry 2 }
--
-- hdsl2Shdsl15MinIntervalES OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Errored Seconds (ES) during the interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl15MinIntervalEntry 3 }
--
-- hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Severely Errored Seconds (SES) during the interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl15MinIntervalEntry 4 }
--
-- hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "detected CRC Anomalies"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of CRC anomalies during the interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl15MinIntervalEntry 5 }
--
-- hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Loss of Sync Word (LOSW) Seconds during the
-- interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl15MinIntervalEntry 6 }
--
-- hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Unavailable Seconds (UAS) during the interval."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl15MinIntervalEntry 7 }
-- Segment Endpoint 1-Day Interval Status/Performance Group
--
-- hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "This table provides one row for each HDSL2/SHDSL endpoint
-- performance data collection interval. This table contains
-- live data from equipment. As such, it is NOT persistent.
-- Entries in this table are created by the system only."
-- ::= { hdsl2ShdslMibObjects 7 }
--
-- hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
-- SYNTAX Hdsl2Shdsl1DayIntervalEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "An entry in the hdsl2Shdsl1DayIntervalTable."
-- INDEX { hdsl2Shdsl1DayIntervalIfIndex }
-- ::= { hdsl2Shdsl1DayIntervalTable 1 }
--
-- Hdsl2Shdsl1DayIntervalEntry ::= SEQUENCE {
-- hdsl2Shdsl1DayIntervalIfIndex INTEGER,
-- hdsl2Shdsl1DayIntervalNumber INTEGER,
-- hdsl2Shdsl1DayIntervalMoniSecs INTEGER,
-- hdsl2Shdsl1DayIntervalES INTEGER,
-- hdsl2Shdsl1DayIntervalSES INTEGER,
-- hdsl2Shdsl1DayIntervalCRCanomalies INTEGER,
-- hdsl2Shdsl1DayIntervalLOSWS INTEGER,
-- hdsl2Shdsl1DayIntervalUAS INTEGER
-- }
--
-- hdsl2Shdsl1DayIntervalIfIndex OBJECT-TYPE
-- SYNTAX INTEGER
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "This object specifies the associated interface index of
-- this HDSL2/SHDSL line."
-- ::= { hdsl2Shdsl1DayIntervalEntry 1 }
--
-- hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
-- SYNTAX INTEGER (1..30)
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "History Data Interval number. Interval 1 is the the most
-- recent previous day; interval 30 is 30 days ago. Intervals
-- 2..30 are optional."
-- ::= { hdsl2Shdsl1DayIntervalEntry 2 }
--
-- hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
-- SYNTAX INTEGER (0..86399)
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "The amount of time in the 1-day interval over which the
-- performance monitoring information is actually counted.
-- This value will be the same as the interval duration except
-- in a situation where performance monitoring data could not
-- be collected for any reason."
-- ::= { hdsl2Shdsl1DayIntervalEntry 3 }
--
-- hdsl2Shdsl1DayIntervalES OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Errored Seconds (ES) during the 1-day interval as
-- measured by hdsl2Shdsl1DayIntervalMoniSecs."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl1DayIntervalEntry 4 }
--
-- hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Severely Errored Seconds (SES) during the 1-day
-- interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl1DayIntervalEntry 5 }
--
-- hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "detected CRC Anomalies"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of CRC anomalies during the 1-day interval as
-- measured by hdsl2Shdsl1DayIntervalMoniSecs."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl1DayIntervalEntry 6 }
--
-- hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Loss of Sync Word (LOSW) Seconds during the 1-day
-- interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl1DayIntervalEntry 7 }
--
-- hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "Count of Unavailable Seconds (UAS) during the 1-day interval
-- as measured by hdsl2Shdsl1DayIntervalMoniSecs."
-- REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
-- ::= { hdsl2Shdsl1DayIntervalEntry 8 }
-- Maintenance Group
--
-- hdsl2ShdslEndpointMaintTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "This table supports maintenance operations (eg. loopbacks)
-- to be performed on HDSL2/SHDSL segment endpoints. This table
-- contains live data from equipment. As such, it is NOT
-- persistent. Entries in this table are created by the system
-- only."
-- ::= { hdsl2ShdslMibObjects 8 }
--
-- hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
-- SYNTAX Hdsl2ShdslEndpointMaintEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "An entry in the hdsl2ShdslEndpointMaintTable. Each entry
-- corresponds to a single segment endpoint, and is indexed by the
-- ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
-- unit and the side of the unit."
-- INDEX { hdsl2ShdslEndpointMaintIfIndex }
-- ::= { hdsl2ShdslEndpointMaintTable 1 }
--
-- Hdsl2ShdslEndpointMaintEntry ::= SEQUENCE {
-- hdsl2ShdslEndpointMaintIfIndex INTEGER,
-- hdsl2ShdslMaintLoopbackConfig INTEGER,
-- hdsl2ShdslMaintTipRingReversal INTEGER,
-- hdsl2ShdslMaintPowerBackOff INTEGER,
-- hdsl2ShdslMaintSoftRestart INTEGER
-- }
--
-- hdsl2ShdslEndpointMaintIfIndex OBJECT-TYPE
-- SYNTAX INTEGER
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "This object specifies the associated interface index of
-- this HDSL2/SHDSL line."
-- ::= { hdsl2ShdslEndpointMaintEntry 1 }
--
-- hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
-- SYNTAX INTEGER {
-- noLoopback(1),
-- normalLoopback(2),
-- specialLoopback(3)
-- }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object controls configuration of loopbacks for the
-- associated segment endpoint. The status of the loopback
-- is obtained via the hdsl2ShdslEndpointCurrStatus object."
-- DEFVAL { noLoopback }
-- ::= { hdsl2ShdslEndpointMaintEntry 2 }
--
-- hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
-- SYNTAX INTEGER {
-- normal(1),
-- reversed(2)
-- }
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "This object indicates the state of the tip/ring pair at the
-- associated segment endpoint."
-- ::= { hdsl2ShdslEndpointMaintEntry 3 }
--
-- hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
-- SYNTAX INTEGER {
-- default(1),
-- enhanced(2)
-- }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the receiver at the associated
-- segment endpoint to operate in default or enhanced power
-- backoff mode."
-- DEFVAL { default }
-- ::= { hdsl2ShdslEndpointMaintEntry 4 }
--
-- hdsl2ShdslMaintSoftRestart OBJECT-TYPE
-- SYNTAX INTEGER {
-- ready(1),
-- restart(2)
-- }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object enables the manager to trigger a soft restart
-- of the modem at the associated segment endpoint. The manager
-- may only set this object to the 'restart(2)' value, which
-- initiates a restart. The agent will perform a restart after
-- approximately 5 seconds. Following the 5 second period, the
-- agent will restore the object to the 'ready(1)' state."
-- DEFVAL { ready }
-- ::= { hdsl2ShdslEndpointMaintEntry 5 }
-- hdsl2ShdslUnitMaintTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "This table supports maintenance operations for units in a
-- HDSL2/SHDSL line. Entries in this table MUST be maintained
-- in a persistent manner. Entries in this table are created by
-- the system only."
-- ::= { hdsl2ShdslMibObjects 9 }
--
-- hdsl2ShdslUnitMaintEntry OBJECT-TYPE
-- SYNTAX Hdsl2ShdslUnitMaintEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "An entry in the hdsl2ShdslUnitMaintTable. Each entry
-- corresponds to a single unit, and is indexed by the ifIndex
-- of the HDSL2/SHDSL line and the UnitId of the associated
-- unit."
-- INDEX { hdsl2ShdslUnitMaintIfIndex }
-- ::= { hdsl2ShdslUnitMaintTable 1 }
--
-- Hdsl2ShdslUnitMaintEntry ::= SEQUENCE {
-- hdsl2ShdslUnitMaintIfIndex INTEGER,
-- hdsl2ShdslMaintLoopbackTimeout INTEGER
-- hdsl2ShdslMaintUnitPowerSource INTEGER
-- }
--
-- hdsl2ShdslUnitMaintIfIndex OBJECT-TYPE
-- SYNTAX INTEGER
-- ACCESS read-only
-- STATUS mandatory
-- bintec NOSAVE
-- DESCRIPTION
-- "This object specifies the associated interface index of
-- this HDSL2/SHDSL line."
-- ::= { hdsl2ShdslUnitMaintEntry 1
--
-- hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
-- SYNTAX INTEGER (0..4095)
-- UNITS "minutes"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the timeout value for loopbacks
-- initiated at segments endpoints contained in the associated
-- unit. A value of 0 disables the timeout."
-- ::= { hdsl2ShdslUnitMaintEntry 2 }
--
-- not supported by GlobeSpan !
--
-- hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
-- SYNTAX INTEGER { local(1), span(2) }
-- ACCESS read-only
-- STATUS mandatory
-- DESCRIPTION
-- "This object indicates the DC power source being used by the
-- associated unit."
-- ::= { hdsl2ShdslUnitMaintEntry 3 }
-- Span Configuration Profile Group
--
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner. Entries in this table are created by
the system only."
::= { hdsl2ShdslMibObjects 10 }
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted only by the system."
INDEX { hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::= SEQUENCE {
hdsl2ShdslSpanConfProfileName DisplayString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate INTEGER,
hdsl2ShdslSpanConfMaxLineRate INTEGER,
-- hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode INTEGER,
-- hdsl2ShdslSpanConfRemoteEnabled INTEGER,
-- hdsl2ShdslSpanConfPowerFeeding INTEGER,
-- hdsl2ShdslSpanConfCurrCondTargetMarginDown INTEGER,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown INTEGER,
-- hdsl2ShdslSpanConfCurrCondTargetMarginUp INTEGER,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp INTEGER
-- hdsl2ShdslSpanConfUsedTargetMargins INTEGER,
-- hdsl2ShdslSpanConfReferenceClock INTEGER,
-- hdsl2ShdslSpanConfLineProbeEnable INTEGER
-- hdsl2ShdslSpanConfProfileRowStatus RowStatus
}
hdsl2ShdslSpanConfProfileName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER {
twoWire(1),
fourWire(2),
fourWireStandard(3),
fourWireIMA(4),
sixWire(5),
sixWireIMA(6),
eightWire(7),
eightWireIMA(8),
not-used(9),
groupMember(10),
twoWireEFM(11),
fourWireEFM(12),
sixWireEFM(13),
eightWireEFM(14)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the bonding mode of
the SHDSL Line.
twoWire(1) : no bonding is used
fourWire(2) : four-wire mode
fourWireStandard(3) : four-wire mode, disable globespan enhanced mode
fourWireIMA(4) : 2 wire pairs bonded with IMA
sixWire(5) : 3 wire pairs in m-pair mode
sixWireIMA(6) : 3 wire pairs bonded with IMA
eightWire(7) : 4 wire pairs in m-pair mode
eightWireIMA(8) : 4 wire pairs bonded with IMA
not-used(9) : wire pair inactive
groupMember(10) : wire pair belongs to a bonding group
twoWireEFM(11) : 2 wire EFM mode
fourWireEFM(12) : 2 wire pairs in EFM mode with PAF bonding
sixWireEFM(13) : 3 wire pairs in EFM mode with PAF bonding
eightWireEFM(14) : 4 wire pairs in EFM mode with PAF bonding"
DEFVAL { twoWire }
::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX INTEGER (0..22784000)
-- UNITS "bps"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
SYNTAX INTEGER (0..22784000)
-- UNITS "bps"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 }
-- hdsl2ShdslSpanConfPSD OBJECT-TYPE
-- SYNTAX INTEGER {
-- symmetric(1),
-- asymmetric(2)
-- }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures use of symmetric/asymmetric PSD (Power
-- Spectral Density) Mask for the associated SHDSL Line. Support
-- for symmetric PSD is mandatory for all supported data rates.
-- Support for asymmetric PSD is optional."
-- DEFVAL { symmetric }
-- ::= { hdsl2ShdslSpanConfProfileEntry 5 }
--
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX INTEGER { region1(1), region2(2) , region1or2(3)}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line:
region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex B"
DEFVAL { region1 }
::= { hdsl2ShdslSpanConfProfileEntry 6 }
-- hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
-- SYNTAX INTEGER {
-- enabled(1),
-- disabled(2)
-- }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object enables/disables support for remote management
-- of the units in a SHDSL line from the STU-R via the EOC."
-- DEFVAL { enabled }
-- ::= { hdsl2ShdslSpanConfProfileEntry 7 }
--
-- not supported by GlobeSpan !
--
-- hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
-- SYNTAX INTEGER { noPower(1), powerFeed(2), wettingCurrent(3) }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object enables/disables support for optional power
-- feeding in a SHDSL line."
-- DEFVAL { noPower }
-- ::= { hdsl2ShdslSpanConfProfileEntry 8 }
-- hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
-- SYNTAX INTEGER (-10..21)
-- UNITS "dB"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object specifies the downstream current condition target
-- SNR margin for a SHDSL line. The SNR margin is the difference
-- between the desired SNR and the actual SNR. Target SNR margin
-- is the desired SNR margin for a unit."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslSpanConfProfileEntry 9 }
--
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX INTEGER (0..65535)
-- UNITS "dB"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 }
-- hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
-- SYNTAX INTEGER (-10..21)
-- UNITS "dB"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object specifies the upstream current condition target
-- SNR margin for a SHDSL line. The SNR margin is the difference
-- between the desired SNR and the actual SNR. Target SNR margin
-- is the desired SNR margin for a unit."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslSpanConfProfileEntry 11 }
--
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX INTEGER (-10..21)
-- UNITS "dB"
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 }
-- hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
-- SYNTAX INTEGER {
-- currCondDown(1),
-- worstCaseDown(2),
-- currCondUp(3),
-- worstCaseUp(4)
-- }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "Contains indicates whether a target SNR margin is enabled or
-- disabled. This is a bit-map of possible settings. The
-- various bit positions are:
--
-- currCondDown current condition downstream target SNR
-- margin enabled
--
-- worstCaseDown worst case downstream target SNR margin
-- enabled
--
-- currCondUp current condition upstream target SNR
-- margin enabled
--
-- worstCaseUp worst case upstream target SNR margin
-- enabled."
-- DEFVAL { currCondDown }
-- ::= { hdsl2ShdslSpanConfProfileEntry 13 }
-- hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
-- SYNTAX INTEGER { localClk(1), networkClk(2),
-- dataOrNetworkClk(3), dataClk(4) }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the clock reference for the STU-C
-- in a SHDSL Line.
-- localClk(1) Mode-1 per G991.2
-- networkClk(2) Mode-2 per G991.2
-- dataOrNetworkClk Mode-3a per G991.2
-- dataClk Mode-3b per G991.2
-- "
-- DEFVAL { localClk }
-- ::= { hdsl2ShdslSpanConfProfileEntry 14 }
--
-- hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
-- SYNTAX INTEGER {
-- disable(1),
-- enable(2)
-- }
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object enables/disables support for Line Probe of
-- the units in a SHDSL line. When Line Probe is enabled, the
-- system performs Line Probing to find the best possible
-- rate. If Line probe is disabled, the rate adaptation phase
-- is skipped to shorten set up time."
-- DEFVAL { disable }
-- ::= { hdsl2ShdslSpanConfProfileEntry 15 }
--
-- hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
-- SYNTAX RowStatus
-- MAX-ACCESS read-create
-- STATUS current
-- DESCRIPTION
-- "This object controls creation/deletion of the associated
-- entry in this table per the semantics of RowStatus. If an
-- active entry is referenced in hdsl2ShdslSpanConfProfile, the
-- entry MUST remain active until all references are removed."
-- ::= { hdsl2ShdslSpanConfProfileEntry 16 }
-- Segment Endpoint Alarm Configuration Profile group
--
-- hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
-- SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- DESCRIPTION
-- "This table supports definitions of alarm configuration
-- profiles for HDSL2/SHDSL segment endpoints. This table
-- MUST be maintained in a persistent manner. Entries in this
-- table are created by the system only."
-- ::= { hdsl2ShdslMibObjects 11 }
--
-- hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
-- SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
-- ACCESS not-accessible
-- STATUS mandatory
-- bintec NODEL
-- DESCRIPTION
-- "Each entry corresponds to a single alarm configuration profile.
-- Each profile contains a set of parameters for setting alarm
-- thresholds for various performance attributes monitored at
-- HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
-- only by the system."
-- INDEX { hdsl2ShdslEndpointAlarmIfIndex }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
--
-- Hdsl2ShdslEndpointAlarmConfProfileEntry ::= SEQUENCE {
-- hdsl2ShdslEndpointAlarmIfIndex INTEGER,
-- hdsl2ShdslEndpointAlarmConfProfileName DisplayString,
-- hdsl2ShdslEndpointThreshLoopAttenuation INTEGER,
-- hdsl2ShdslEndpointThreshSNRMargin INTEGER,
-- hdsl2ShdslEndpointThreshES INTEGER,
-- hdsl2ShdslEndpointThreshSES INTEGER,
-- hdsl2ShdslEndpointThreshCRCanomalies INTEGER,
-- hdsl2ShdslEndpointThreshLOSWS INTEGER,
-- hdsl2ShdslEndpointThreshUAS INTEGER
-- hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
-- }
--
-- hdsl2ShdslEndpointAlarmIfIndex OBJECT-TYPE
-- SYNTAX INTEGER
-- ACCESS read-only
-- STATUS mandatory
-- DESCRIPTION
-- "This object specifies the associated interface index of
-- this HDSL2/SHDSL line."
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 10 }
--
-- hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
-- SYNTAX DisplayString (SIZE(1..32))
-- ACCESS read-only
-- STATUS mandatory
-- DESCRIPTION
-- "This object is the unique index associated with this profile."
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
--
-- not supported by GlobeSpan !
--
-- hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
-- SYNTAX INTEGER (-127..128)
-- UNITS "dB"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the loop attenuation alarm threshold.
-- When the current value of hdsl2ShdslEndpointCurrAtn reaches
-- or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing
-- MAY be generated."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
--
-- hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
-- SYNTAX INTEGER (-127..128)
-- UNITS "dB"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the SNR margin alarm threshold.
-- When the current value of hdsl2ShdslEndpointCurrSnrMgn
-- reaches or drops below this threshold, a
-- hdsl2ShdslSNRMarginCrossing MAY be generated."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
--
-- hdsl2ShdslEndpointThreshES OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the threshold for the number of
-- errored seconds (ES) within any given 15-minute performance
-- data collection interval. If the value of errored seconds
-- in a particular 15-minute collection interval reaches/
-- exceeds this value, a hdsl2ShdslPerfESThresh MAY be
-- generated. At most one notification will be sent per
-- interval per endpoint."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
--
-- hdsl2ShdslEndpointThreshSES OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the threshold for the number of
-- severely errored seconds (SES) within any given 15-minute
-- performance data collection interval. If the value of
-- severely errored seconds in a particular 15-minute collection
-- interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh
-- MAY be generated. At most one notification will be sent per
-- interval per endpoint."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
--
-- hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "detected CRC Anomalies"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the threshold for the number of
-- CRC anomalies within any given 15-minute performance data
-- collection interval. If the value of CRC anomalies in a
-- particular 15-minute collection interval reaches/exceeds
-- this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be
-- generated. At most one notification will be sent per
-- interval per endpoint."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
--
-- hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the threshold for the number of
-- Loss of Sync Word (LOSW) Seconds within any given 15-minute
-- performance data collection interval. If the value of LOSW
-- in a particular 15-minute collection interval reaches/exceeds
-- this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated.
-- At most one notification will be sent per interval per
-- endpoint."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
--
-- hdsl2ShdslEndpointThreshUAS OBJECT-TYPE
-- SYNTAX INTEGER
-- UNITS "seconds"
-- ACCESS read-write
-- STATUS mandatory
-- DESCRIPTION
-- "This object configures the threshold for the number of
-- unavailable seconds (UAS) within any given 15-minute
-- performance data collection interval. If the value of UAS
-- in a particular 15-minute collection interval reaches/exceeds
-- this value, a hdsl2ShdslPerfUASThresh MAY be generated.
-- At most one notification will be sent per interval per
-- endpoint."
-- DEFVAL { 0 }
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
--
-- hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
-- SYNTAX RowStatus
-- MAX-ACCESS read-create
-- STATUS current
-- DESCRIPTION
-- "This object controls creation/deletion of the associated
-- entry in this table as per the semantics of RowStatus.
-- If an active entry is referenced in either
-- hdsl2ShdslSpanConfAlarmProfile or
-- hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
-- active until all references are removed."
-- ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
-- Notifications Group
--
--
-- hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
--
-- hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrAtn,
-- hdsl2ShdslEndpointThreshLoopAttenuation
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the loop attenuation
-- threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
-- value) has been reached/exceeded for the HDSL2/SHDSL segment
-- endpoint."
-- ::= { hdsl2ShdslNotifications 1 }
--
-- hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrSnrMgn,
-- hdsl2ShdslEndpointThreshSNRMargin
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the SNR margin threshold (as
-- per the hdsl2ShdslEndpointThreshSNRMargin value) has been
-- reached/exceeded for the HDSL2/SHDSL segment endpoint."
-- ::= { hdsl2ShdslNotifications 2 }
--
-- hdsl2ShdslPerfESThresh NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurr15MinES,
-- hdsl2ShdslEndpointThreshES
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the errored seconds threshold
-- (as per the hdsl2ShdslEndpointThreshES value) has been reached/
-- exceeded for the HDSL2/SHDSL segment endpoint."
-- ::= { hdsl2ShdslNotifications 3 }
--
-- hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurr15MinSES,
-- hdsl2ShdslEndpointThreshSES
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the severely errored seconds
-- threshold (as per the hdsl2ShdslEndpointThreshSES value) has
-- been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
-- ::= { hdsl2ShdslNotifications 4 }
--
-- hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurr15MinCRCanomalies,
-- hdsl2ShdslEndpointThreshCRCanomalies
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the CRC anomalies threshold
-- (as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
-- been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
-- ::= { hdsl2ShdslNotifications 5 }
--
-- hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurr15MinLOSWS,
-- hdsl2ShdslEndpointThreshLOSWS
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the LOSW seconds threshold
-- (as per the hdsl2ShdslEndpointThreshLOSWS value) has been
-- reached/exceeded for the HDSL2/SHDSL segment endpoint."
-- ::= { hdsl2ShdslNotifications 6 }
--
-- hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurr15MinUAS,
-- hdsl2ShdslEndpointThreshUAS
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the unavailable seconds
-- threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
-- been reached/exceeded for the HDSL2/SHDSL segment endpoint."
-- ::= { hdsl2ShdslNotifications 7 }
--
-- hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslSpanConfNumRepeaters
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that a mismatch has been detected
-- between the number of repeater/regenerator units configured
-- for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
-- object and the actual number of repeater/regenerator units
-- discovered via the EOC."
-- ::= { hdsl2ShdslNotifications 8 }
--
-- hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslMaintLoopbackConfig
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that an endpoint maintenance
-- loopback command failed for an HDSL2/SHDSL segment."
-- ::= { hdsl2ShdslNotifications 9 }
--
-- hdsl2ShdslpowerBackoff NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the bit setting for
-- powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
-- this endpoint has changed."
-- ::= { hdsl2ShdslNotifications 10 }
--
-- hdsl2ShdsldeviceFault NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the bit setting for
-- deviceFault in the hdsl2ShdslEndpointCurrStatus object for
-- this endpoint has changed."
-- ::= { hdsl2ShdslNotifications 11 }
--
-- hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the bit setting for
-- dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
-- for this endpoint has changed."
-- ::= { hdsl2ShdslNotifications 12 }
--
-- hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the bit setting for
-- configInitFailure in the hdsl2ShdslEndpointCurrStatus object
-- for this endpoint has changed."
-- ::= { hdsl2ShdslNotifications 13 }
--
-- hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the bit setting for
-- protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
-- object for this endpoint has changed."
-- ::= { hdsl2ShdslNotifications 14 }
--
-- hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslEndpointCurrStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates that the bit setting for
-- noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
-- for this endpoint has changed."
-- ::= { hdsl2ShdslNotifications 15 }
--
-- hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE OBJECTS {
-- hdsl2ShdslInvVendorID
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This notification indicates impending unit failure due to
-- loss of local power (last gasp)."
-- ::= { hdsl2ShdslNotifications 16 }
--
-- conformance information
--
--
-- hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
-- hdsl2ShdslGroups OBJECT IDENTIFIER ::=
-- { hdsl2ShdslConformance 1 }
-- hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
-- { hdsl2ShdslConformance 2 }
-- agent compliance statements
--
-- hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
-- STATUS mandatory
-- DESCRIPTION
-- "The section outlines compliance requirements for this MIB."
-- MODULE
-- MANDATORY-GROUPS {
-- hdsl2ShdslSpanConfGroup,
-- hdsl2ShdslSpanStatusGroup,
-- hdsl2ShdslInventoryGroup,
-- hdsl2ShdslEndpointConfGroup,
-- hdsl2ShdslEndpointCurrGroup,
-- hdsl2Shdsl15MinIntervalGroup,
-- hdsl2Shdsl1DayIntervalGroup,
-- hdsl2ShdslMaintenanceGroup,
-- hdsl2ShdslEndpointAlarmConfGroup,
-- hdsl2ShdslNotificationGroup
-- }
--
-- GROUP hdsl2ShdslInventoryShdslGroup
-- DESCRIPTION
-- "Support for this group is only required for implementations
-- supporting SHDSL lines."
--
-- GROUP hdsl2ShdslSpanShdslStatusGroup
-- DESCRIPTION
-- "Support for this group is only required for implementations
-- supporting SHDSL lines."
--
-- GROUP hdsl2ShdslSpanConfProfileGroup
-- DESCRIPTION
-- "Support for this group is only required for implementations
-- supporting SHDSL lines."
--
-- ::= { hdsl2ShdslCompliances 1 }
--
--
-- units of conformance
--
-- hdsl2ShdslSpanConfGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslSpanConfNumRepeaters,
-- hdsl2ShdslSpanConfProfile,
-- hdsl2ShdslSpanConfAlarmProfile
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects for configuring span related
-- parameters for HDSL2/SHDSL lines."
-- ::= { hdsl2ShdslGroups 1 }
--
-- hdsl2ShdslSpanStatusGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslStatusNumAvailRepeaters
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects for retrieving span related
-- status for HDSL2/SHDSL lines."
-- ::= { hdsl2ShdslGroups 2 }
--
-- hdsl2ShdslInventoryShdslGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslInvTransmissionModeCapability
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects for retrieving SHDSL-specific
-- inventory information."
-- ::= { hdsl2ShdslGroups 3 }
--
-- hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslStatusMaxAttainableLineRate,
-- hdsl2ShdslStatusActualLineRate,
-- hdsl2ShdslStatusTransmissionModeCurrent
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects for retrieving SHDSL-specific
-- span related status."
-- ::= { hdsl2ShdslGroups 4 }
--
-- hdsl2ShdslInventoryGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslInvVendorID,
-- hdsl2ShdslInvVendorModelNumber,
-- hdsl2ShdslInvVendorSerialNumber,
-- hdsl2ShdslInvVendorEOCSoftwareVersion,
-- hdsl2ShdslInvStandardVersion,
-- hdsl2ShdslInvVendorListNumber,
-- hdsl2ShdslInvVendorIssueNumber,
-- hdsl2ShdslInvVendorSoftwareVersion,
-- hdsl2ShdslInvEquipmentCode,
-- hdsl2ShdslInvVendorOther
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects that provide unit inventory
-- information about the units in HDSL2/SHDSL lines."
-- ::= { hdsl2ShdslGroups 5 }
--
-- hdsl2ShdslEndpointConfGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslEndpointCurrAtn
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects for configuring parameters for
-- segment endpoints in HDSL2/SHDSL lines."
-- ::= { hdsl2ShdslGroups 6 }
--
-- hdsl2ShdslEndpointCurrGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslEndpointCurrAtn,
-- hdsl2ShdslEndpointCurrSnrMgn,
-- hdsl2ShdslEndpointCurrStatus,
-- hdsl2ShdslEndpointES,
-- hdsl2ShdslEndpointSES,
-- hdsl2ShdslEndpointCRCanomalies,
-- hdsl2ShdslEndpointLOSWS,
-- hdsl2ShdslEndpointUAS,
-- hdsl2ShdslEndpointCurr15MinTimeElapsed,
-- hdsl2ShdslEndpointCurr15MinES,
-- hdsl2ShdslEndpointCurr15MinSES,
-- hdsl2ShdslEndpointCurr15MinCRCanomalies,
-- hdsl2ShdslEndpointCurr15MinLOSWS,
-- hdsl2ShdslEndpointCurr15MinUAS,
-- hdsl2ShdslEndpointCurr1DayTimeElapsed,
-- hdsl2ShdslEndpointCurr1DayES,
-- hdsl2ShdslEndpointCurr1DaySES,
-- hdsl2ShdslEndpointCurr1DayCRCanomalies,
-- hdsl2ShdslEndpointCurr1DayLOSWS,
-- hdsl2ShdslEndpointCurr1DayUAS
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects which provide current status and
-- performance measurements relating to segment endpoints in
-- HDSL2/SHDSL lines."
-- ::= { hdsl2ShdslGroups 7 }
--
-- hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP OBJECTS {
-- hdsl2Shdsl15MinIntervalES,
-- hdsl2Shdsl15MinIntervalSES,
-- hdsl2Shdsl15MinIntervalCRCanomalies,
-- hdsl2Shdsl15MinIntervalLOSWS,
-- hdsl2Shdsl15MinIntervalUAS
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects which maintain historic
-- performance measurements relating to segment endpoints in
-- HDSL2/SHDSL lines in 15-minute intervals."
-- ::= { hdsl2ShdslGroups 8 }
--
-- hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP OBJECTS {
-- hdsl2Shdsl1DayIntervalMoniSecs,
-- hdsl2Shdsl1DayIntervalES,
-- hdsl2Shdsl1DayIntervalSES,
-- hdsl2Shdsl1DayIntervalCRCanomalies,
-- hdsl2Shdsl1DayIntervalLOSWS,
-- hdsl2Shdsl1DayIntervalUAS
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects which maintain historic
-- performance measurements relating to segment endpoints in
-- HDSL2/SHDSL lines in 1-day intervals."
-- ::= { hdsl2ShdslGroups 9 }
--
-- hdsl2ShdslMaintenanceGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslMaintLoopbackConfig,
-- hdsl2ShdslMaintTipRingReversal,
-- hdsl2ShdslMaintPowerBackOff,
-- hdsl2ShdslMaintSoftRestart,
-- hdsl2ShdslMaintLoopbackTimeout,
-- hdsl2ShdslMaintUnitPowerSource
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects that provide support for
-- maintenance actions for HDSL2/SHDSL lines."
-- ::= { hdsl2ShdslGroups 10 }
--
-- hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslEndpointAlarmConfProfile,
-- hdsl2ShdslEndpointThreshLoopAttenuation,
-- hdsl2ShdslEndpointThreshSNRMargin,
-- hdsl2ShdslEndpointThreshES,
-- hdsl2ShdslEndpointThreshSES,
-- hdsl2ShdslEndpointThreshCRCanomalies,
-- hdsl2ShdslEndpointThreshLOSWS,
-- hdsl2ShdslEndpointThreshUAS,
-- hdsl2ShdslEndpointAlarmConfProfileRowStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects that allow configuration of alarm
-- thresholds for various performance parameters for HDSL2/SHDSL
-- lines."
-- ::= { hdsl2ShdslGroups 11 }
--
-- hdsl2ShdslNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS {
-- hdsl2ShdslLoopAttenCrossing,
-- hdsl2ShdslSNRMarginCrossing,
-- hdsl2ShdslPerfESThresh,
-- hdsl2ShdslPerfSESThresh,
-- hdsl2ShdslPerfCRCanomaliesThresh,
-- hdsl2ShdslPerfLOSWSThresh,
-- hdsl2ShdslPerfUASThresh,
-- hdsl2ShdslSpanInvalidNumRepeaters,
-- hdsl2ShdslLoopbackFailure,
-- hdsl2ShdslpowerBackoff,
-- hdsl2ShdsldeviceFault,
-- hdsl2ShdsldcContinuityFault,
-- hdsl2ShdslconfigInitFailure,
-- hdsl2ShdslprotocolInitFailure,
-- hdsl2ShdslnoNeighborPresent,
-- hdsl2ShdslLocalPowerLoss
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports notifications of significant conditions
-- associated with HDSL2/SHDSL lines."
-- ::= { hdsl2ShdslGroups 12 }
--
-- hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP OBJECTS {
-- hdsl2ShdslSpanConfWireInterface,
-- hdsl2ShdslSpanConfMinLineRate,
-- hdsl2ShdslSpanConfMaxLineRate,
-- hdsl2ShdslSpanConfPSD,
-- hdsl2ShdslSpanConfTransmissionMode,
-- hdsl2ShdslSpanConfRemoteEnabled,
-- hdsl2ShdslSpanConfPowerFeeding,
-- hdsl2ShdslSpanConfCurrCondTargetMarginDown,
-- hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
-- hdsl2ShdslSpanConfCurrCondTargetMarginUp,
-- hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
-- hdsl2ShdslSpanConfUsedTargetMargins,
-- hdsl2ShdslSpanConfReferenceClock,
-- hdsl2ShdslSpanConfLineProbeEnable,
-- hdsl2ShdslSpanConfProfileRowStatus
-- }
-- STATUS mandatory
-- DESCRIPTION
-- "This group supports objects that constitute configuration
-- profiles for configuring span related parameters in SHDSL
-- lines."
-- ::= { hdsl2ShdslGroups 13 }
END
View Git Blame Copy Permalink