WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/aricent/ARICENT-QOS-MIB

2750 lines
102 KiB
Plaintext
Raw Permalink Blame History

-- Copyright (C) 2008-2012 Aricent Group . All Rights Reserved
-- $Id: fsqosxtd.mib,v 1.25 2016/07/05 07:38:42 siva Exp $
-- ========================================================================== --
-- DIFF SERVER DATA PATH FLOW --
-- ========================================================================== --
--
-- +==========+ +========+ +==========+
-- Traffic | | | | +==========+ InProf | |
-- | | | | | |( green,| |
-- | Classify | | Pre | | | yellow)| Marking, |
-- ========>| |===>| Marking|===>| Metering |=======>| |
-- | | | | +====+=====+ +==>| |
-- +==========+ +========+ | | +==========+
-- | | |
-- OutProfile=====+ |
-- (red) (soft police) |
-- | |
-- | |
-- | |
-- (hard police) |
-- | |
-- +==========+ |
-- | pkt drop | |
-- +==========+ |
-- |
-- |
-- +===============+ +===============+ |
-- Tx to egress port| |<=====| Queueing / | |
-- <=============== | Scheduling/ | | Shaping |======+
-- | Rate-Shaping | | |
-- +===============+ +===============+
-- ========================================================================== --
ARICENT-QOS-MIB DEFINITIONS ::= BEGIN
IMPORTS
Unsigned32, MODULE-IDENTITY, OBJECT-TYPE, enterprises, Integer32,
Counter64 FROM SNMPv2-SMI
ifIndex FROM IF-MIB
TEXTUAL-CONVENTION, RowStatus, DisplayString, TruthValue FROM SNMPv2-TC;
fsQoSMib MODULE-IDENTITY
LAST-UPDATED "201209050000Z"
ORGANIZATION "ARICENT COMMUNICATIONS SOFTWARE"
CONTACT-INFO "support@aricent.com"
DESCRIPTION
"This MIB defines the objects necessary to manage
a device that uses the Differentiated Services."
REVISION "201209050000Z"
DESCRIPTION
"This MIB defines the objects necessary to manage
a device that uses the Differentiated Services."
::= { enterprises aricent-communication-holding-ltd(29601) iss(2) 6}
Dscp ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A Differentiated Services Code-Point that may be used for
marking a traffic stream."
REFERENCE
"RFC 2474, RFC 2780"
SYNTAX Integer32 (0..63)
MeterColorMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Enums to indicate the color mode of the Meter
colorAware - the Meter will also consider the Pre-Color
of the Packet
colorBlind - the Meter will ignore the Pre-Color of the Packet"
SYNTAX INTEGER {
colorAware(1),
colorBlind(2)
}
MeterType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Enums to indicate the meter type :
SimpleTokenBucket - Two Parameter Token Bucket Meter as described in
the Informal Differentiated Services Model section
5.2.3.
AvgRate - Average Rate Meter as described in the Informal
Differentiated Services Model section 5.2.1.
SrTCM - Single Rate Three Color Marker Metering as defined
by RFC 2697.
TrTCM - Two Rate Three Color Marker Metering as defined by
RFC 2698.
TswTCM - Time Sliding Window Three Color Marker Metering as
defined by RFC 2859.
mefDecoupledMeter - Dual bucket meter as defined by RFC 4115.
mefCoupledMeter - Dual bucket meter as defined by RFC 2697 and
MEF coupling Flag."
SYNTAX INTEGER {
simpleTokenBucket(1),
avgRate(2),
srTCM(3),
trTCM(4),
tswTCM(5),
mefDecoupledMeter(6),
mefCoupledMeter(7)
}
EnableStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "A textual convention to Enable or Disable a MIB contruct."
SYNTAX INTEGER {
enable(1),
disable(2)
}
SchedulerPriority ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"Scheduler Priority which a flow should fall in."
SYNTAX Integer32 (0..15)
IndexInteger ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"An integer which may be used as a table index. If 0 then it is invalid"
SYNTAX Unsigned32 (0..65535)
-- ========================================================================== --
-- groups in the MIB --
-- ========================================================================== --
fsQoSMIBObjects OBJECT IDENTIFIER ::= { fsQoSMib 1 }
-- System Object to support system specific scalars.
fsQoSSystem OBJECT IDENTIFIER ::= { fsQoSMIBObjects 1 }
-- Class Table
fsQoSClass OBJECT IDENTIFIER ::= { fsQoSMIBObjects 2 }
-- Policy Table : Meter and Action tables
fsQoSPolicy OBJECT IDENTIFIER ::= { fsQoSMIBObjects 3 }
-- Traffic Management Tables for shaping , managing queues and scheduling them
fsQoSTrafficMgmt OBJECT IDENTIFIER ::= { fsQoSMIBObjects 4 }
-- Stats
fsQoSStats OBJECT IDENTIFIER ::= { fsQoSMIBObjects 5 }
-- Rate Control Table : For CPU port
fsQosHwCpuRateControl OBJECT IDENTIFIER ::= { fsQoSMIBObjects 6 }
fsQoSSystemControl OBJECT-TYPE
SYNTAX INTEGER { shutdown(0), start(1) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Starts or shutdowns QoS Module in the system.
When set as 'start',resources required by QoS module are
allocated & QoS module starts running.
When shutdown, all the pools used by QoS module will be
released to the system."
::= { fsQoSSystem 1 }
fsQoSStatus OBJECT-TYPE
SYNTAX INTEGER { disabled(0), enabled(1) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables or Disables QoS Module in the system.
When set as 'enabled', QoS module programs the hardware
and starts Protocol Operation.
When set as 'disabled', it stops protocol operation by
deleting the hardware configuration.
If any mib table supports global configurations (less-specific)
at runtime and H/W supports more-specific configurations,
then appropriate behaviour may take effect in H/W only after next
status change of this object."
DEFVAL { enabled }
::= { fsQoSSystem 2 }
fsQoSTrcFlag OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable trace statements in QoS module.
A four byte integer is used for enabling the trace level.
Each bit in the four byte integer represents a particular
trace level.
The mapping between the bit positions & the trace level is
as follows:
0 - Init and Shutdown traces
1 - Management traces
2 - Data Path traces
3 - Control Plane traces
5 - Traces related to all resources except buffers
6 - Buffer allocation/release traces
7 - All Failure traces
None of the bit is set the Disable the Trace,value(0).
The remaining bits are unused. Combination of levels are
also allowed.
For example if the bits 0 and 1 are set, then the trace
statement related to Init-Shutdown and management
will be printed.
The user has to enter the corresponding integer value for the
bits set. For example if bits 0 and 1 are to be set ,then user
has to give the value 3."
::= { fsQoSSystem 3 }
fsQoSRateUnit OBJECT-TYPE
SYNTAX INTEGER
{
bps(1),
kbps(2),
mbps(3),
gbps(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This Object indicates the unit for the
Information Rate(CIR,EIR,PIR,PTR,CTR ...)values
based on target platform.
This Object specifies the unit alone. Value corresponding
to this unit should be taken from 'fsQoSRateGranularity'
Ex 1:
'fsQoSRateUnit' = kbps
'fsQoSRateGranularity' = 64
then this target will accept the Information
Rate(CIR,EIR,TIR,PTR, CTR ...) values in multiples of 64
like 64 kbps, 128 kbps ...
Ex 2:
'fsQoSRateUnit' = mbps
'fsQoSRateGranularity' = 64
then this target will accept the Information
Rate(CIR,EIR,TIR,PTR, CTR ...) values in multiples of 64
like 64 mbps, 128 mbps ..."
::= { fsQoSSystem 4 }
fsQoSRateGranularity OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This Object indicates the acceptable Granularity level
for configuring the Information Rate(CIR,EIR,PIR,PTR,
CTR ...)values for a target platform.
This Object specifies the Integer Value for the
granularity. Unit for
this value should be taken from 'fsQoSRateUnit'
Ex 1:
'fsQoSRateUnit' = kbps
'fsQoSRateGranularity' = 64
then this target will accept the Information
Rate(CIR,EIR,TIR,PTR, CTR ...) values in multiples of 64
like 64 kbps, 128 kbps ...
Ex 2:
'fsQoSRateUnit' = mbps
'fsQoSRateGranularity' = 64
then this target will accept the Information
Rate(CIR,EIR,TIR,PTR, CTR ...) values in multiples of 64
like 64 mbps, 128 mbps ..."
::= { fsQoSSystem 5 }
-- ========================================================================== --
-- Priority Map Table --
-- ========================================================================== --
fsQoSPriorityMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSPriorityMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table to map incoming priority to a regenerated priority.
This table is used to regenerate port/VLAN priorities for an
incoming packet. It can be used to directly program priority
tables in the hardware."
::= { fsQoSClass 1 }
fsQoSPriorityMapEntry OBJECT-TYPE
SYNTAX FsQoSPriorityMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry to map an incoming priority, drop-precedence to a
regenerated priority value for an ingress PORT/VLAN. The PORT/VLAN
indices may take dont-care (0) values as required."
INDEX { fsQoSPriorityMapID }
::= { fsQoSPriorityMapTable 1 }
FsQoSPriorityMapEntry ::=
SEQUENCE {
fsQoSPriorityMapID IndexInteger,
fsQoSPriorityMapName DisplayString,
fsQoSPriorityMapIfIndex Unsigned32,
fsQoSPriorityMapVlanId Unsigned32,
fsQoSPriorityMapInPriority Integer32,
fsQoSPriorityMapInPriType INTEGER,
fsQoSPriorityMapRegenPriority Unsigned32,
fsQoSPriorityMapRegenInnerPriority Unsigned32,
fsQoSPriorityMapConfigStatus INTEGER,
fsQoSPriorityMapStatus RowStatus,
fsQoSPriorityMapInDEI INTEGER,
fsQoSPriorityMapRegenColor INTEGER
}
fsQoSPriorityMapID OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" The output priority map index for the incoming packet received over
ingress PORT/VLAN with specified incoming priority. This is unique for
each entry in the priority-map table."
::= { fsQoSPriorityMapEntry 1 }
fsQoSPriorityMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..31))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This indicates the Name for the Priority map entry.
It should be unique in this Table."
::= { fsQoSPriorityMapEntry 2 }
fsQoSPriorityMapIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Incoming Port Number. The PORT may take dont-care (0) values
as required."
DEFVAL { 0 }
::= { fsQoSPriorityMapEntry 3 }
fsQoSPriorityMapVlanId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Vlan Id for Priority regeneration.The VlanId may
take dont-care (0) values as required."
DEFVAL { 0 }
::= { fsQoSPriorityMapEntry 4 }
fsQoSPriorityMapInPriority OBJECT-TYPE
SYNTAX Integer32 (0..63)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The incoming Priority value determined for the received frame.
This value is equivalent to the priority( VLAN (4 bit)/DSCP( 6 bit)
priority bits) indicated in the received frame, or one of the
evaluated priorities."
DEFVAL { 0 }
::= { fsQoSPriorityMapEntry 5 }
fsQoSPriorityMapInPriType OBJECT-TYPE
SYNTAX INTEGER { vlanPri(0),
ipTos(1),
ipDscp(2),
mplsExp(3),
vlanDEI(4),
dot1P(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Incoming Priority Type is used to Identify the
'fsQoSPriorityMapInPriority' value is a vlanPri or IP TOS or IP DSCP
or MPLS EXP or dot1P. If the incoming Priority type is 802.1P, the incoming
packet priority and drop_eligible can be supported. If incoming DEI
'fsQoSPriorityMapInDEI' is not set by the administrator, the
drop_eligible bit is set as 0 by default."
DEFVAL { 0 }
::= { fsQoSPriorityMapEntry 6 }
fsQoSPriorityMapRegenPriority OBJECT-TYPE
SYNTAX Unsigned32 (0..63)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Regenerated Priority value determined for the received frame."
DEFVAL { 0 }
::= { fsQoSPriorityMapEntry 7 }
fsQoSPriorityMapRegenInnerPriority OBJECT-TYPE
SYNTAX Unsigned32 (0..8)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Regenerated Inner-VLAN (CVLAN) Priority value determined
for the received frame. It the Values is 8 then this object is not
configured by user"
::= { fsQoSPriorityMapEntry 8 }
fsQoSPriorityMapConfigStatus OBJECT-TYPE
SYNTAX INTEGER {
sysdefault(1),
management(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The status of the prority map entry. Indicates whether
entry is configured by management or is a default entry."
DEFVAL { sysdefault }
::= { fsQoSPriorityMapEntry 9 }
fsQoSPriorityMapStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified at any time.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise returns inconsistentValue error.
For any mib table that supports global configurations (less-specific) at runtime
and H/W supports more-specific configurations, if a more-specific entry is deleted
by configuration, then the next less-specific entry gets programmed to H/W"
::= { fsQoSPriorityMapEntry 10 }
fsQoSPriorityMapInDEI OBJECT-TYPE
SYNTAX INTEGER { false(0),
true(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Drop_eligible bit in the incoming frames.
Either it can take false(0) or true (1). By default, drop_eligible bit is
not set."
DEFVAL { 0 }
::= { fsQoSPriorityMapEntry 11 }
fsQoSPriorityMapRegenColor OBJECT-TYPE
SYNTAX INTEGER {
green(0), -- Traffic conforms to SLAs
yellow(1), -- Traffic exceeds the SLAs
red (2) -- Traffic violates the SLAs
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the regenerated color determined for the received frame."
DEFVAL { 0 }
::= { fsQoSPriorityMapEntry 12 }
-- ========================================================================== --
-- MultiField ClassMap Table --
-- ========================================================================== --
fsQoSClassMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSClassMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the Multifield Classifier details. It takes input
from the ACL or priority-map table and outputs a CLASS for the
traffic-class pattern/match."
::= { fsQoSClass 2 }
fsQoSClassMapEntry OBJECT-TYPE
SYNTAX FsQoSClassMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Multi-field Classifier entry maps an ACL entry or a priority-map
to a CLASS of Service."
INDEX { fsQoSClassMapId }
::= { fsQoSClassMapTable 1 }
-- This table outputs a CLASS for the input FilterId/Priority-MAP.
FsQoSClassMapEntry ::= SEQUENCE {
fsQoSClassMapId IndexInteger,
fsQoSClassMapName DisplayString,
-- input ACL/Priority-Map ID
fsQoSClassMapL2FilterId Unsigned32,
fsQoSClassMapL3FilterId Unsigned32,
fsQoSClassMapPriorityMapId Unsigned32,
-- outputs
fsQoSClassMapCLASS Unsigned32,
fsQoSClassMapClfrId Unsigned32,
fsQoSClassMapPreColor INTEGER, -- Color b4 Meter
fsQoSClassMapStatus RowStatus,
fsQoSClassMapVlanMapId Unsigned32
}
fsQoSClassMapId OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that enumerates the MultiField Classifier table."
::= { fsQoSClassMapEntry 1 }
fsQoSClassMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..31))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This indicates the Name for the Entry.Multiple ACL/priority-map
entries can map to the same CLASS. They need to be configured with
the same ClassMapName."
::= { fsQoSClassMapEntry 2 }
fsQoSClassMapL2FilterId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object specifies the ID of the MAC filter, the details of which
should be matched against the incoming packet. A valid value of this
object is not mandatory for the creation of the conceptual row. However,
L2/L3 FilterId is mutually exclusive to the Priority-Map Id. One
of them is a mandatory input for an entry."
DEFVAL { 0 }
::= { fsQoSClassMapEntry 3 }
fsQoSClassMapL3FilterId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object specifies the ID of the IP filter, the details of which
should be matched against the incoming packet. A valid value of this
object is not mandatory for the creation of the conceptual row. However,
L2/L3 FilterId is mutually exclusive to the Priority-Map Id. One
of them is a mandatory input for an entry."
DEFVAL { 0 }
::= { fsQoSClassMapEntry 4 }
fsQoSClassMapPriorityMapId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object specifies the priority map ID for mapping incoming priority
against received packet.A valid value of this
object is not mandatory for the creation of the conceptual row. However,
L2/L3 FilterId is mutually exclusive to the Priority-Map Id. One
of them is a mandatory input for an entry."
DEFVAL { 0 }
::= { fsQoSClassMapEntry 5 }
fsQoSClassMapCLASS OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This represents the Traffic CLASS to which an incoming frame pattern
is classified. The administrator needs to define the logical groups
that represent this CLASS. Multiple ACL/priority-map entries can
map to the same CLASS value. '0' is not configurable but it is the
default value."
DEFVAL { 0 }
::= { fsQoSClassMapEntry 6 }
fsQoSClassMapClfrId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This represents the Classifier Id of teh Classifier in the Standard Qos Entry.
This used to get the datapath entry pointing to teh CLass-Map with respect to the
Standard MIB"
DEFVAL { 0 }
::= { fsQoSClassMapEntry 7 }
fsQoSClassMapPreColor OBJECT-TYPE
SYNTAX INTEGER {
none (0), -- Traffic is not pre-colored
green(1), -- Traffic conforms to SLAs
yellow(2), -- Traffic exceeds the SLAs
red (3) -- Traffic violates the SLAs
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This represents the color of the packet prior to metering.
The default Drop-Precedence for the packet can be evaluated
using this object. This value is overridden by the meter."
::= { fsQoSClassMapEntry 8 }
fsQoSClassMapVlanMapId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the VLAN Map ID for mapping an incoming VLAN
to an Egress Subscriber Queue. Filter ID/ Priority-Map Id are mutually
exclusive to the Vlan Map Id. One of them is a mandatory input for a
class-map entry."
::= { fsQoSClassMapEntry 9 }
fsQoSClassMapStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified only when the row status is not active.
CreateAndGo not allowed ,it can be deleted 'destroy',
only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSClassMapEntry 10 }
-- ========================================================================== --
-- ClassToPriority Table --
-- ========================================================================== --
fsQoSClassToPriorityTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSClassToPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table assigns local priority values for a input CLASS. This table
is optional and can be configured as per user requirement. This table
is provided for easy mapping of CLASS to priority values.
A set of non-contiguous CLASS values belong to a
unique Group ( identified by a group name)."
::= { fsQoSClass 3 }
fsQoSClassToPriorityEntry OBJECT-TYPE
SYNTAX FsQoSClassToPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry to specify a regenerated priority value for a input CLASS."
INDEX { fsQoSClassToPriorityCLASS }
::= { fsQoSClassToPriorityTable 1 }
-- This table maps a CLASS to a regenerated priority value.
FsQoSClassToPriorityEntry ::= SEQUENCE {
fsQoSClassToPriorityCLASS IndexInteger,
fsQoSClassToPriorityRegenPri Unsigned32,
fsQoSClassToPriorityGroupName DisplayString,
fsQoSClassToPriorityStatus RowStatus
}
fsQoSClassToPriorityCLASS OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This represents the Traffic CLASS to which an incoming frame pattern
is classified. The administrator needs to define the traffic
class patterns that represent this CLASS. Multiple
ACL/priority-map entries can map to the same CLASS value."
::= { fsQoSClassToPriorityEntry 1 }
fsQoSClassToPriorityRegenPri OBJECT-TYPE
SYNTAX Unsigned32 (0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Regenerated Priority value determined for the input CLASS."
::= { fsQoSClassToPriorityEntry 2 }
fsQoSClassToPriorityGroupName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..31))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This is for unique identification of the group to which a input
CLASS belongs."
::= { fsQoSClassToPriorityEntry 3 }
fsQoSClassToPriorityStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified only when the row status is not active.
it can be deleted 'destroy', only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSClassToPriorityEntry 4 }
-- ========================================================================== --
-- Meter Table --
-- ========================================================================== --
-- The below is as per RFC 3289 ( std qos diffserv mib).
-- This MIB supports a variety of Meters. It includes a specific
-- definition for Token Bucket Meter, which are but one type of
-- specification.
-- Configuration of various meter parameters is as follows :
-- AvgRate meter
-- Average Rate = CIR
-- Avg. Interval = Interval
-- srTCM meters (RFC 2697) can be specified using CIR, CBS and EBS.
-- trTCM meters (RFC 2698) can be specified using CIR, CBS, PIR, PBS where
-- PIR = EIR,
-- PBS = EBS.
-- tswTCM meters (RFC 2859) can be specified using CTR, PTR and Avg. Interval
-- where
-- CTR = CIR,
-- PTR = EIR
-- Average Interval = Interval.
-- MEF based meter bandwidth attributes -
-- CIR, EIR , CBS, EBS where EBS should mean max burst size.
-- single bucket parameters - CIR, CBS, EBS
-- dual bucket parameters - CIR, EIR, CBS and EBS where EIR - max rate
--
fsQoSMeterTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSMeterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table enumerates specific meters that a system may use to
police a stream of traffic. This may include all traffic on an
interface."
::= { fsQoSPolicy 1 }
fsQoSMeterEntry OBJECT-TYPE
SYNTAX FsQoSMeterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the meter table describes a single conformance level
of a meter."
INDEX { fsQoSMeterId }
::= { fsQoSMeterTable 1 }
FsQoSMeterEntry ::= SEQUENCE {
fsQoSMeterId IndexInteger,
fsQoSMeterName DisplayString,
fsQoSMeterType MeterType,
fsQoSMeterInterval Unsigned32,
fsQoSMeterColorMode MeterColorMode,
fsQoSMeterCIR Unsigned32,
fsQoSMeterCBS Unsigned32,
fsQoSMeterEIR Unsigned32,
fsQoSMeterEBS Unsigned32,
fsQoSMeterNext Unsigned32,
fsQoSMeterStatus RowStatus
}
fsQoSMeterId OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index that enumerates the Meter entries."
::= { fsQoSMeterEntry 1 }
fsQoSMeterName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..31))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This indicates the Name for the meter entry.
It should be unique in this Table."
::= { fsQoSMeterEntry 2 }
fsQoSMeterType OBJECT-TYPE
SYNTAX MeterType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Metering algorithm associated with the Token Bucket meter."
::= { fsQoSMeterEntry 3 }
fsQoSMeterInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..10000)
UNITS "microseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The time interval used with the token bucket. For:
1. Average Rate Meter, the Informal Differentiated Services Model
section 5.2.1, - Delta.
2. Simple Token Bucket Meter, the Informal Differentiated
Services Model section 5.1, - time interval t.
3. RFC 2859 TSWTCM, - AVG_INTERVAL.
4. RFC 2697 srTCM, RFC 2698 trTCM, - token bucket update time
interval."
DEFVAL { 0 }
::= { fsQoSMeterEntry 4 }
fsQoSMeterColorMode OBJECT-TYPE
SYNTAX MeterColorMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The user defined Meter Color Mode."
DEFVAL { colorBlind }
::= { fsQoSMeterEntry 5 }
fsQoSMeterCIR OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The committed information rate as per MEF.
Must be >= 0. CIR must be less than or equal to EIR, if EIR > 0"
::= { fsQoSMeterEntry 6 }
fsQoSMeterCBS OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "Bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The committed burst size as per MEF. Must be > 0 if CIR > 0.
Maximum allowable size will be jumbo frame size."
::= { fsQoSMeterEntry 7 }
fsQoSMeterEIR OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The excess information rate as per MEF.
Must be >= 0. EIR must be greater than or equal to CIR,
if EIR > 0. This is not applicable when MeterType is srtcm."
::= { fsQoSMeterEntry 8 }
fsQoSMeterEBS OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "Bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The excess burst size as per MEF. Must be > 0 if EIR > 0."
::= { fsQoSMeterEntry 9 }
fsQoSMeterNext OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This specifies the meter entry ID to be used for applying the
second/next level of conformance on the incoming packet. A valid
value of this object is not mandatory for the creation of an
entry in the conceptual row."
DEFVAL { 0 }
::= { fsQoSMeterEntry 10 }
fsQoSMeterStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified only of the Entry is not ACTIVE.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSMeterEntry 11 }
-- ========================================================================== --
-- Policy-Map Table ( ClassMap To PolicyMap Table ) --
-- ========================================================================== --
fsQoSPolicyMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSPolicyMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table contains the class-map to policy-map details."
::= { fsQoSPolicy 2 }
fsQoSPolicyMapEntry OBJECT-TYPE
SYNTAX FsQoSPolicyMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry to map a policy for a class-map."
INDEX { fsQoSPolicyMapId }
::= { fsQoSPolicyMapTable 1 }
FsQoSPolicyMapEntry ::= SEQUENCE {
fsQoSPolicyMapId IndexInteger,
fsQoSPolicyMapName DisplayString,
-- inputs
fsQoSPolicyMapIfIndex Unsigned32,
fsQoSPolicyMapCLASS Unsigned32,
-- outputs
fsQoSPolicyMapPHBType INTEGER,
fsQoSPolicyMapDefaultPHB Unsigned32, -- default outgoing priority
fsQoSPolicyMapMeterTableId Unsigned32, -- meter
fsQoSPolicyMapFailMeterTableId Unsigned32,
-- actions
fsQoSPolicyMapInProfileConformActionId Unsigned32,
fsQoSPolicyMapInProfileConformActionFlag BITS,
fsQoSPolicyMapInProfileActionSetPort Unsigned32, -- for conform, exceed actions
fsQoSPolicyMapConformActionSetIpTOS Unsigned32,
fsQoSPolicyMapConformActionSetDscp Dscp,
fsQoSPolicyMapConformActionSetVlanPrio Unsigned32,
fsQoSPolicyMapConformActionSetVlanDE Unsigned32,
fsQoSPolicyMapConformActionSetInnerVlanPrio Unsigned32,
fsQoSPolicyMapConformActionSetMplsExp Unsigned32,
fsQoSPolicyMapConformActionSetNewCLASS Unsigned32,
fsQoSPolicyMapInProfileExceedActionId Unsigned32,
fsQoSPolicyMapInProfileExceedActionFlag BITS,
fsQoSPolicyMapExceedActionSetIpTOS Unsigned32,
fsQoSPolicyMapExceedActionSetDscp Dscp,
fsQoSPolicyMapExceedActionSetInnerVlanPrio Unsigned32,
fsQoSPolicyMapExceedActionSetVlanPrio Unsigned32,
fsQoSPolicyMapExceedActionSetVlanDE Unsigned32,
fsQoSPolicyMapExceedActionSetMplsExp Unsigned32,
fsQoSPolicyMapExceedActionSetNewCLASS Unsigned32,
fsQoSPolicyMapOutProfileActionId Unsigned32,
fsQoSPolicyMapOutProfileActionFlag BITS,
fsQoSPolicyMapOutProfileActionSetIPTOS Unsigned32,
fsQoSPolicyMapOutProfileActionSetDscp Dscp,
fsQoSPolicyMapOutProfileActionSetInnerVlanPrio Unsigned32,
fsQoSPolicyMapOutProfileActionSetVlanPrio Unsigned32,
fsQoSPolicyMapOutProfileActionSetVlanDE Unsigned32,
fsQoSPolicyMapOutProfileActionSetMplsExp Unsigned32,
fsQoSPolicyMapOutProfileActionSetNewCLASS Unsigned32,
fsQoSPolicyMapStatus RowStatus,
fsQoSPolicyMapConformActionSetInnerVlanDE Unsigned32,
fsQoSPolicyMapExceedActionSetInnerVlanDE Unsigned32,
fsQoSPolicyMapOutProfileActionSetInnerVlanDE Unsigned32,
fsQoSPolicyDefaultVlanDE INTEGER
}
fsQoSPolicyMapId OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An index that enumerates the policy-map table entries."
::= { fsQoSPolicyMapEntry 1 }
fsQoSPolicyMapName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..31))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This the Name for a policy entry. It should be unique in this Table."
::= { fsQoSPolicyMapEntry 2 }
fsQoSPolicyMapIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This indicates the incoming interface identifier for which the policy
map is applied. A Valid value of this object is not mandatory for the
creation of an entry in this table."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 3 }
fsQoSPolicyMapCLASS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This indicates the Traffic CLASS for which the policy-map
needs to be applied. A valid value is not necessary for
creation of an entry in this table. When this object is configured as
dont-care(0), it is mandatory that the PolicyMapIfIndex is
configured. This implies that the policy is interface-specific
and not CLASS-specific."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 4 }
fsQoSPolicyMapPHBType OBJECT-TYPE
SYNTAX INTEGER {
none(0),
vlanPri(1),
ipTos(2),
ipDscp(3),
mplsExp(4),
dot1P(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "It indicates the PHB type to be used for filling the Default PHB
for the policy-map entry."
::= { fsQoSPolicyMapEntry 5 }
fsQoSPolicyMapDefaultPHB OBJECT-TYPE
SYNTAX Unsigned32 (0..63)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "It indicate the default out going PHB Values for the
Policy-Map. It may be overriden by the Meter used for the policy-map.
This value is interpreted by fsQoSPolicyMapPHBType."
::= { fsQoSPolicyMapEntry 6 }
fsQoSPolicyMapMeterTableId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Object refers to a Meter table Id which is the index
for the Meter table. A Valid value of this object is
not mandatory for the creation of an entry in this table."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 7 }
fsQoSPolicyMapFailMeterTableId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Object refers to a Meter table Id which is the index
of the Meter pointed to by diffServMeterFailNext.
A Valid value of this object is not mandatory for the
creation of an entry in this table."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 8 }
fsQoSPolicyMapInProfileConformActionFlag OBJECT-TYPE
SYNTAX BITS {
none(0),
setFlagPort(1),
setFlagConfTos(2), -- mark TOS
setFlagConfDscp(3), -- mark DSCP
setFlagConfVlanPrio(4), -- mark vlan priority
setFlagConfVlanDE(5), -- mark vlan DE
setFlagConfInnerVlanPrio(6), -- mark inner vlan priority
setFlagConfMplsExp(7), -- mark MPLS exp
setFlagConfInnerVlanDE(8) -- mark inner vlan DEI
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object defines the action to be performed on the packet,
when the packets are found to be In profile."
::= { fsQoSPolicyMapEntry 9 }
fsQoSPolicyMapInProfileConformActionId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Object refers to an Action table Id which is the index
for the Action table. This is for the reference of the StdQos mib.
where we have to mention an action table for each action.
A Valid value of this object is
not mandatory for the creation of an entry in this table."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 10 }
fsQoSPolicyMapInProfileActionSetPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object sets the new port value in case the action
selected by fsQoSPolicyMapInProfileActionFlag is to assign a new
out port value."
::= { fsQoSPolicyMapEntry 11 }
fsQoSPolicyMapConformActionSetIpTOS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object sets the new IP TOS value in case the action
selected by fsQoSPolicyMapInProfileActionFlag is to assign a new
IP TOS value."
::= { fsQoSPolicyMapEntry 12 }
fsQoSPolicyMapConformActionSetDscp OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object sets the new DSCP value in case the action
selected by fsQoSPolicyMapInProfileActionFlag is to assign a new
DSCP value."
::= { fsQoSPolicyMapEntry 13 }
fsQoSPolicyMapConformActionSetVlanPrio OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Vlan Priority of the outgoing packet.
Setting of Vlan Priority is mutually exclusive to setting of Mpls EXP bits.
So setting the Vlan Priority to a non-zero value is only allowed when MplsExp is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 14 }
fsQoSPolicyMapConformActionSetVlanDE OBJECT-TYPE
SYNTAX Unsigned32 ( 0..1 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the VLAN Drop Eligible Indicator of the outgoing packet.
This is applicable ONLY when MplsExp is 0"
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 15 }
fsQoSPolicyMapConformActionSetInnerVlanPrio OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Inner Vlan Priority of the outgoing packet."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 16 }
fsQoSPolicyMapConformActionSetMplsExp OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Mpls Experimental bits of the outgoing packet.
Either Vlan Priority can be set OR Mpls EXP bits
can be set. So setting the Mpls EXP to a non 0
value is only allowed when Vlan Prio is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 17 }
fsQoSPolicyMapConformActionSetNewCLASS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This represents the Traffic CLASS to which an incoming frame pattern
is classified after metering. The priority of the New CLASS should
be lower as compared to the CLASS assigned prior to metering.
The administrator needs to ensure that the new CLASS belongs
to the same logical group as the CLASS assigned prior to metering.
In cases where lower priority CLASS cannot be assigned, the
administrator needs to appropriately configure for dropping the packet.
"
::= { fsQoSPolicyMapEntry 18 }
fsQoSPolicyMapInProfileExceedActionFlag OBJECT-TYPE
SYNTAX BITS {
setFlagExcDrop(0),
setFlagExcTos(1), -- mark for exceed action
setFlagExcDscp(2),
setFlagExcVlanPrio(3),
setFlagExcVlanDE(4),
setFlagExcInnerVlanPrio(5),
setFlagExcMplsExp(6),
setFlagExcInnerVlanDE(7)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object defines the action to be performed on the packet,
when the packets are found to be In profile."
::= { fsQoSPolicyMapEntry 19 }
fsQoSPolicyMapInProfileExceedActionId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Object refers to an Action table Id which is the index
for the Action table. This is for the reference of the StdQos mib.
where we have to mention an action table for each action.
A Valid value of this object is
not mandatory for the creation of an entry in this table."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 20 }
fsQoSPolicyMapExceedActionSetIpTOS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object sets the new IP TOS value in case the action
selected by fsQoSPolicyMapInProfileActionFlag is to assign a new
IP TOS value."
::= { fsQoSPolicyMapEntry 21 }
fsQoSPolicyMapExceedActionSetDscp OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object sets the new DSCP value in case the action
selected by fsQoSPolicyMapInProfileActionFlag is to assign a new
DSCP value."
::= { fsQoSPolicyMapEntry 22 }
fsQoSPolicyMapExceedActionSetInnerVlanPrio OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Vlan Priority of the outgoing packet.
Either Vlan Priority can be set OR Mpls EXP bits
can be set. So setting the Vlan Priority to a non-zero
value is only allowed when MplsExp is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 23 }
fsQoSPolicyMapExceedActionSetVlanPrio OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Inner-Vlan Priority of the outgoing packet."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 24 }
fsQoSPolicyMapExceedActionSetVlanDE OBJECT-TYPE
SYNTAX Unsigned32 ( 0..1 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the VLAN Drop Eligible Indicator of the outgoing packet.
This is applicable ONLY when MplsEXP is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 25 }
fsQoSPolicyMapExceedActionSetMplsExp OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Mpls Experimental bits of the outgoing packet.
Either Vlan Priority can be set OR Mpls EXP bits
can be set. So setting the Mpls EXP to a non-zero
value is only allowed when Vlan Prio is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 26 }
fsQoSPolicyMapExceedActionSetNewCLASS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This represents the Traffic CLASS to which an incoming frame pattern
is classified after metering. The priority of the New CLASS should
be lower as compared to the CLASS assigned prior to metering.
The administrator needs to ensure that the new CLASS belongs
to the same logical group as the CLASS assigned prior to metering.
In cases where lower priority CLASS cannot be assigned, the
administrator needs to appropriately configure for dropping the packet.
"
::= { fsQoSPolicyMapEntry 27 }
fsQoSPolicyMapOutProfileActionFlag OBJECT-TYPE
SYNTAX BITS {
setFlagDrop(0), -- packet is dropped
setFlagTos(1), -- mark IP TOS
setFlagDscp(2), -- mark DSCP
setFlagVlanPrio(3), -- mark VLAN priority
setFlagVlanDE(4), -- mark VLAN DE
setFlagConfInnerVlanPrio(5), -- mark inner vlan priority
setFlagMplsExp(6), -- mark MPLS EXP bits
setFlagConfInnerVlanDE(7) -- mark inner vlan DEI
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object defines the action to be performed on the packet
when the packets are found to be out of profile."
::= { fsQoSPolicyMapEntry 28 }
fsQoSPolicyMapOutProfileActionId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Object refers to an Action table Id which is the index
for the Action table. This is for the reference of the StdQos mib.
where we have to mention an action table for each action.
A Valid value of this object is
not mandatory for the creation of an entry in this table."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 29 }
fsQoSPolicyMapOutProfileActionSetIPTOS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object sets the new IP TOS value in case the action
selected by fsQoSPolicyMapOutProfileActionFlag is to assign a new
Ip TOS value."
::= { fsQoSPolicyMapEntry 30 }
fsQoSPolicyMapOutProfileActionSetDscp OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object sets the new DSCP value in case the action
selected by fsQoSPolicyMapOutProfileActionFlag is to assign
a new DSCP value."
::= { fsQoSPolicyMapEntry 31 }
fsQoSPolicyMapOutProfileActionSetInnerVlanPrio OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Vlan Priority of the outgoing packet.
Either Vlan Priority can be set OR Mpls EXP bits
can be set. So setting the Vlan Priority to a non-zero
value is only allowed when is MplsExp is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 32 }
fsQoSPolicyMapOutProfileActionSetVlanPrio OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Inner Vlan Priority of the outgoing packet.
Either Vlan Priority can be set OR Mpls EXP bits
can be set. So setting the Vlan Priority to a non-zero
value is only allowed when is MplsExp is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 33 }
fsQoSPolicyMapOutProfileActionSetVlanDE OBJECT-TYPE
SYNTAX Unsigned32 ( 0..1 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the VLAN Drop Eligible Indicator of the outgoing packet.
This is applicable ONLY when MplsEXP is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 34 }
fsQoSPolicyMapOutProfileActionSetMplsExp OBJECT-TYPE
SYNTAX Unsigned32 ( 0..7 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Mpls Experimental bits of the outgoing packet.
Either Vlan Priority can be set OR Mpls EXP bits
can be set. So setting the Mpls EXP to a non-zero
value is only allowed when is Vlan Prio is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 35 }
fsQoSPolicyMapOutProfileActionSetNewCLASS OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This represents the Traffic CLASS to which an incoming frame pattern
is classified after metering. The priority of the New CLASS should
be lower as compared to the CLASS assigned prior to metering.
The administrator needs to ensure that the new CLASS belongs
to the same logical group as the CLASS assigned prior to metering. In cases,
where lower-priority CLASS cannot be assigned, administrator needs to
appropriately configure for dropping the packet."
::= { fsQoSPolicyMapEntry 36 }
fsQoSPolicyMapStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row."
::= { fsQoSPolicyMapEntry 37 }
fsQoSPolicyMapConformActionSetInnerVlanDE OBJECT-TYPE
SYNTAX Unsigned32 ( 0..1 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Inner VLAN Drop Eligible Indicator of the outgoing packet.
Either Inner VLAN DE can be set OR Mpls EXP bits can be set. So setting
the Inner VLAN DE is only allowed when MplsExp is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 38 }
fsQoSPolicyMapExceedActionSetInnerVlanDE OBJECT-TYPE
SYNTAX Unsigned32 ( 0..1 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Inner VLAN Drop Eligible Indicator of the outgoing packet.
Either Inner VLAN DE can be set OR Mpls EXP bits can be set. So setting
the Inner VLAN DE is only allowed when MplsExp is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 39 }
fsQoSPolicyMapOutProfileActionSetInnerVlanDE OBJECT-TYPE
SYNTAX Unsigned32 ( 0..1 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting the Inner VLAN Drop Eligible Indicator of the outgoing packet.
Either Inner VLAN DE can be set OR Mpls EXP bits can be set. So setting
the Inner VLAN DE is only allowed when MplsExp is 0."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 40 }
fsQoSPolicyDefaultVlanDE OBJECT-TYPE
SYNTAX INTEGER ( 0..1 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to set the VLAN Drop Eligible Indicator of the outgoing packet."
DEFVAL { 0 }
::= { fsQoSPolicyMapEntry 41 }
-- ========================================================================== --
-- Queue Template Table : --
-- A template to specify the queue parameters ,the policing algo parameters --
-- applied on the queue. --
-- ========================================================================== --
fsQoSQTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSQTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The queue template table configures the queue attributes.
The template is re-used for configuring multiple queues."
::= { fsQoSTrafficMgmt 1 }
fsQoSQTemplateEntry OBJECT-TYPE
SYNTAX FsQoSQTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Each entry in the table is a Queue Template Configuration."
INDEX { fsQoSQTemplateId }
::= { fsQoSQTemplateTable 1 }
FsQoSQTemplateEntry ::= SEQUENCE {
fsQoSQTemplateId IndexInteger,
fsQoSQTemplateName DisplayString,
fsQoSQTemplateDropType INTEGER,
fsQoSQTemplateDropAlgoEnableFlag EnableStatus,
fsQoSQTemplateSize Unsigned32,
fsQoSQTemplateStatus RowStatus
}
fsQoSQTemplateId OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Queue Template Table Index."
::= { fsQoSQTemplateEntry 1 }
fsQoSQTemplateName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..31))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This the Name for a Entry. It should be unique in this Table."
::= { fsQoSQTemplateEntry 2 }
fsQoSQTemplateDropType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
tailDrop(2),
headDrop(3),
red(4),
alwaysDrop(5),
wred(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of drop algorithm used by this queue template. The value
other(1)requires further specification in some other MIB module.
In the tailDrop(2) algorithm, fsQoSQTemplateSize
represents the maximum depth of the queue, beyond which all newly
arriving packets will be dropped.
In the headDrop(3) algorithm, if a packet arrives when the current
depth of the queue, is at fsQoSQTemplateSize , packets
currently at the head of the queue are dropped to make room for the
new packet to be enqueued at the tail of the queue.
In the random Drop(4) and (6) algorithms, on packet arrival, an Active
Queue Management algorithm is executed which may randomly drop a
packet. This algorithm may be proprietary, and it may drop either
the arriving packet or another packet in the queue.
For this algorithm, fsQoSQTemplateSize is understood to
be the absolute maximum size of the queue and additional parameters are
described in fsQoSRandomDetectCfgTable.
The alwaysDrop(5) algorithm is as its name specifies; always
drop. In this case, the other configuration values in this Entry
are not meaningful"
::= { fsQoSQTemplateEntry 3 }
fsQoSQTemplateDropAlgoEnableFlag OBJECT-TYPE
SYNTAX EnableStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Enable/disable Drop Algorithm for Congestion Management"
DEFVAL { disable }
::= { fsQoSQTemplateEntry 4 }
fsQoSQTemplateSize OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Queue Size. This must be greater than or equal to the
fsQoSRandomDetectCfgMinAvgThresh and less-than/equal to
fsQoSRandomDetectCfgMaxAvgThresh if Random Detection is enabled.
This is depth in bytes of the queue being measured, at
which a trigger is generated to the dropping algorithm.
For the tailDrop(2) or headDrop(3) algorithms, this represents
the depth of the queue, at which the drop action will take place.
Other algorithms will need to define their own semantics for this
threshold."
::= { fsQoSQTemplateEntry 5 }
fsQoSQTemplateStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified at any time.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSQTemplateEntry 6 }
-- ========================================================================== --
-- RED configuration for Q Congestion Management --
-- The below is configured if RED needs to be enabled in the system. --
-- fsQoSQTemplateDropSpecific points to an entry in this --
-- table. --
-- ========================================================================== --
fsQoSRandomDetectCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSRandomDetectCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table to configure parameters for Random Detect Algorithm.
The table is Indexed by fsQoSQTemplateId and
Drop Precedence (DP) (0 - 2).
Each entry represent random detect configurations
per QueueTemplate per Drop Precedence."
::= { fsQoSTrafficMgmt 2 }
fsQoSRandomDetectCfgEntry OBJECT-TYPE
SYNTAX FsQoSRandomDetectCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in the table is a random drop Configuration."
INDEX { fsQoSQTemplateId , fsQoSRandomDetectCfgDP }
::= { fsQoSRandomDetectCfgTable 1 }
FsQoSRandomDetectCfgEntry ::=
SEQUENCE {
fsQoSRandomDetectCfgDP Integer32,
fsQoSRandomDetectCfgMinAvgThresh Unsigned32,
fsQoSRandomDetectCfgMaxAvgThresh Unsigned32,
fsQoSRandomDetectCfgMaxPktSize Unsigned32,
fsQoSRandomDetectCfgMaxProb Unsigned32,
fsQoSRandomDetectCfgExpWeight Unsigned32,
fsQoSRandomDetectCfgStatus RowStatus,
fsQoSRandomDetectCfgGain Unsigned32,
fsQoSRandomDetectCfgDropThreshType INTEGER,
fsQoSRandomDetectCfgECNThresh Unsigned32,
fsQoSRandomDetectCfgActionFlag BITS
}
fsQoSRandomDetectCfgDP OBJECT-TYPE
SYNTAX Integer32(0..5)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The Drop Precedence [Drop Profile]
0 - low drop precedence[TCP Green Discard]
1 - medium drop precedence[TCP Yellow Discard]
2 - high drop precedence[TCP Red Discard]
3 - [NON-TCP Green Discard]
4 - [NON-TCP Yellow Discard]
5 - [NON-TCP Red Discard]"
::= { fsQoSRandomDetectCfgEntry 1 }
fsQoSRandomDetectCfgMinAvgThresh OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum average threshold for the random detect algorithm.
Below this threshold, packets are admitted into the queue.
The units are bits in accordance with Traffic Manager.
This must be less than or equal to the
fsQoSRandomDetectCfgMaxAvgThresh and the Queue size."
::= { fsQoSRandomDetectCfgEntry 2 }
fsQoSRandomDetectCfgMaxAvgThresh OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum average threshold for the random detect algorithm.
Above this threshold, packets are discarded before entering
the queue. The units is bits in accordance with Traffic Manager.
This must be greater than or equal to the
fsQoSRandomDetectCfgMinAvgThresh and less than or equal to the
Queue size."
::= { fsQoSRandomDetectCfgEntry 3 }
fsQoSRandomDetectCfgMaxPktSize OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Maximum allowed Packet Size. The units is bytes."
::= { fsQoSRandomDetectCfgEntry 4 }
fsQoSRandomDetectCfgMaxProb OBJECT-TYPE
SYNTAX Unsigned32(1..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum probability of discarding a packet in units of percentage."
DEFVAL { 100 }
::= { fsQoSRandomDetectCfgEntry 5 }
fsQoSRandomDetectCfgExpWeight OBJECT-TYPE
SYNTAX Unsigned32(0..31)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The exponential Weight for determining the average queue size."
DEFVAL{ 0 }
::= { fsQoSRandomDetectCfgEntry 6 }
fsQoSRandomDetectCfgStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified at any time.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSRandomDetectCfgEntry 7 }
fsQoSRandomDetectCfgGain OBJECT-TYPE
SYNTAX Unsigned32(0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Gain defines an increase in drop-probability on each granular
increase of buffer-occupancy due to received traffic.
Determines the smoothing that should be applied."
::= { fsQoSRandomDetectCfgEntry 8 }
fsQoSRandomDetectCfgDropThreshType OBJECT-TYPE
SYNTAX INTEGER {
discardpackets(1),
discardbytes(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"discardpackets(1) sets the WRED drop type to Discard packets.
discardbytes(2) sets the WRED drop type to discard in terms of bytes.
Value configured for fsQoSRandomDetectCfgMinAvgThresh and
fsQoSRandomDetectCfgMaxAvgThresh is interpreted as Packets/Bytes
based on the this object configuration."
DEFVAL { 1 }
::= { fsQoSRandomDetectCfgEntry 9 }
fsQoSRandomDetectCfgECNThresh OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Defines the Queue depth in bytes to stop marking and start dropping
ECN eligible packets"
::= { fsQoSRandomDetectCfgEntry 10 }
fsQoSRandomDetectCfgActionFlag OBJECT-TYPE
SYNTAX BITS {
none(0),
capavg(1),
markcongestion(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This Object defines the additional action flags for the WRED profiles,
Setting the flag to capavg(0) never lets the average queue size be bigger
than the actual queue size. markcongestion(1) marks the ECN instead of
dropping.
Action performed by this Flag configurations is dependent on the underlying
Platform, if the platform supports this configuration."
DEFVAL { 0 }
::= { fsQoSRandomDetectCfgEntry 11 }
-- ========================================================================== --
-- Shape Template Table --
-- ========================================================================== --
fsQoSShapeTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSShapeTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" The shape template table configures the shaper attributes."
::= { fsQoSTrafficMgmt 3 }
fsQoSShapeTemplateEntry OBJECT-TYPE
SYNTAX FsQoSShapeTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Each entry in the table is a Shape Template Configuration."
INDEX { fsQoSShapeTemplateId }
::= { fsQoSShapeTemplateTable 1 }
FsQoSShapeTemplateEntry ::= SEQUENCE {
fsQoSShapeTemplateId IndexInteger,
fsQoSShapeTemplateName DisplayString,
fsQoSShapeTemplateCIR Unsigned32,
fsQoSShapeTemplateCBS Unsigned32,
fsQoSShapeTemplateEIR Unsigned32,
fsQoSShapeTemplateEBS Unsigned32,
fsQoSShapeTemplateStatus RowStatus
}
fsQoSShapeTemplateId OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Shape Template Table Index."
::= { fsQoSShapeTemplateEntry 1 }
fsQoSShapeTemplateName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..31))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This the Name for a Shape template Entry.
It should be unique in this Table."
::= { fsQoSShapeTemplateEntry 2 }
fsQoSShapeTemplateCIR OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The committed information rate for packets through this queue.
Must be > 0."
::= { fsQoSShapeTemplateEntry 3 }
fsQoSShapeTemplateCBS OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "Bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The committed burst size for packets through this queue.
Must be > 0 when CIR > 0."
::= { fsQoSShapeTemplateEntry 4 }
fsQoSShapeTemplateEIR OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Excess information rate for packets through this hierarchy.
Must be >= 0. EIR must be greater than or equal to CIR, if EIR > 0.
Currently not used, for future use.
Agent returns EIR = 0 to represent that this row is not configured by
the manager."
::= { fsQoSShapeTemplateEntry 5 }
fsQoSShapeTemplateEBS OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "Bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The excess burst size for packets through this hierarchy.
Must be > 0 when EIR > 0. Currently not used, for future use.
Agent returns EBS = 0 to represent that this row is not configured by
the manager."
::= { fsQoSShapeTemplateEntry 6 }
fsQoSShapeTemplateStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified at any time.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSShapeTemplateEntry 7 }
-- ========================================================================== --
-- Queue Map Table --
-- ========================================================================== --
fsQoSQMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSQMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Queue MAP table mapping an egress port,
CLASS of service to a queue."
::= { fsQoSTrafficMgmt 4 }
fsQoSQMapEntry OBJECT-TYPE
SYNTAX FsQoSQMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Q MAP Entry mapping a CLASS of service or
RegenPriority from the fsQoSPolicyMapTable to a queue."
INDEX { ifIndex, fsQoSQMapCLASS, fsQoSQMapRegenPriType,
fsQoSQMapRegenPriority }
::= { fsQoSQMapTable 1 }
FsQoSQMapEntry ::=
SEQUENCE {
fsQoSQMapCLASS Unsigned32,
fsQoSQMapRegenPriType INTEGER,
fsQoSQMapRegenPriority Unsigned32,
fsQoSQMapQId Unsigned32,
fsQoSQMapStatus RowStatus,
fsQoSQMapRegenDEI Unsigned32,
fsQoSQMapRegenColor Unsigned32
}
fsQoSQMapCLASS OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The input CLASS ( associated with an incoming packet) that needs
to be mapped to an outbound queue. This is mutually exclusive to
the RegenPriority object. CLASS should be 0 while configuring
RegenPriority specific Q."
::= { fsQoSQMapEntry 1 }
fsQoSQMapRegenPriType OBJECT-TYPE
SYNTAX INTEGER {
none(0),
vlanPri(1),
ipTos(2),
ipDscp(3),
mplsExp(4),
vlanDEI(5),
internalPrio(6),
dot1P(7)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The regenerated-priority type to interpret the value of
'fsQoSQMapRegenPriority' object. This object should be none
while configuring CLASS specific Queue.
If fsQoSQMapRegenPriType is internalPrio, then packets classified to
internal priority will be associated to queue with identfier
fsQoSQMapQId"
::= { fsQoSQMapEntry 2 }
fsQoSQMapRegenPriority OBJECT-TYPE
SYNTAX Unsigned32(0..63)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The regenerated-priority ( for an incoming packet) that needs
to be mapped to an outbound queue. This is mutually exclusive to
the CLASS configuration. This object should be 0 while configuring
CLASS specific Queue."
::= { fsQoSQMapEntry 3 }
fsQoSQMapQId OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Queue Identifier that uniquely identifies a queue relative to an
interface. It could be configured with a unique value in the system."
::= { fsQoSQMapEntry 4 }
fsQoSQMapStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects in this
row may be modified only when the row status is not active.
It can be deleted/destroyed independent of other Traffic class tables;
For any mib table that supports global configurations (less-specific)
at runtime and H/W supports more-specific configurations,
if a more-specific entry is deleted by configuration, then the next
less-specific entry gets programmed to H/W
If the fsQoSQMapCLASS associated to this table refers the flow based
traffic classification, Interface index configuration as part fsQoSQMap
table is not required. Interface index associated on the L2/L3 filters
will be applicable for QueueMapping as well.
For Vlan based queueing, egress interface should be configured for
mapping the classified egress vlan traffic to subscriber queues."
::= { fsQoSQMapEntry 5 }
fsQoSQMapRegenDEI OBJECT-TYPE
SYNTAX INTEGER { false(0),
true(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Drop_eligible bit in the incoming frames.
Either it can take false(0) or true (1). By default,
drop_eligible bit is not set."
DEFVAL { 0 }
::= { fsQoSQMapEntry 6 }
fsQoSQMapRegenColor OBJECT-TYPE
SYNTAX INTEGER { green(0), ---Traffic conforms to SLAs
yellow(1),---Traffic exceeds to SLAs
red(2) ---Traffic violates to SLAs
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the regenerated color used in COSQ mapping.
Administrator is not allowed to configure the color for Queue
Mapping. This object will reflect the color configured
in Priority Map."
::= { fsQoSQMapEntry 7 }
-- ========================================================================== --
-- Queue Table --
-- ========================================================================== --
fsQoSQTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSQEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table describing the queue parameters"
::= { fsQoSTrafficMgmt 5 }
fsQoSQEntry OBJECT-TYPE
SYNTAX FsQoSQEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION " Q table entry"
INDEX {ifIndex, fsQoSQId }
::= { fsQoSQTable 1 }
FsQoSQEntry ::=
SEQUENCE {
fsQoSQId Unsigned32,
fsQoSQCfgTemplateId Unsigned32,
fsQoSQSchedulerId Unsigned32,
fsQoSQWeight Unsigned32,
fsQoSQPriority Unsigned32,
fsQoSQShapeId Unsigned32,
fsQoSQStatus RowStatus,
fsQoSQType Unsigned32
}
fsQoSQId OBJECT-TYPE
SYNTAX Unsigned32 ( 1..65535 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Queue Identifier that uniquely identifies the queue
in the system/port."
::= { fsQoSQEntry 1 }
fsQoSQCfgTemplateId OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Queue template Id applied for configuring queue attributes."
::= { fsQoSQEntry 2 }
fsQoSQSchedulerId OBJECT-TYPE
SYNTAX Unsigned32 ( 1..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The scheduler identifier that manages the specified queue.
This identifier is unique relative to an egress interface."
::= { fsQoSQEntry 3 }
fsQoSQWeight OBJECT-TYPE
SYNTAX Unsigned32 (0..1000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"User assigned weight to the CoS queue.
The assigned weights are used only when scheduling
algorithm is a weighted scheduling algorithm."
DEFVAL { 1 }
::= { fsQoSQEntry 4 }
fsQoSQPriority OBJECT-TYPE
SYNTAX Unsigned32 (0..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"User assigned priority for the CoS queue.
The assigned priority is used only when the scheduler uses a
priority based scheduling algorithm."
DEFVAL { 1 }
::= { fsQoSQEntry 5 }
fsQoSQShapeId OBJECT-TYPE
SYNTAX Unsigned32 ( 0..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The shaper identifier that specifies the bandwidth requirements
for the queue. This object is not mandatory for the
creation of the row."
::= { fsQoSQEntry 6 }
fsQoSQStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "Row Status to Create/Destroy the entry.
It can be deleted 'destroy', only if it is not referenced
by other dependent tables; otherwise it returns inconsistentValue error."
::= { fsQoSQEntry 7 }
fsQoSQType OBJECT-TYPE
SYNTAX Unsigned32 (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the type of the queue.
1- Unicast queue
2- Multicast queue
3- Subscriber queue"
DEFVAL { 1 }
::= { fsQoSQEntry 8 }
-- ========================================================================== --
-- Scheduler Table --
-- ========================================================================== --
fsQoSSchedulerTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSSchedulerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Scheduler table "
::= { fsQoSTrafficMgmt 6 }
fsQoSSchedulerEntry OBJECT-TYPE
SYNTAX FsQoSSchedulerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Scheduler table Entry."
INDEX { ifIndex, fsQoSSchedulerId }
::= { fsQoSSchedulerTable 1 }
FsQoSSchedulerEntry ::=
SEQUENCE {
fsQoSSchedulerId Unsigned32,
fsQoSSchedulerSchedAlgorithm INTEGER,
fsQoSSchedulerShapeId Unsigned32,
fsQoSSchedulerHierarchyLevel Unsigned32,
fsQoSSchedulerGlobalId Unsigned32,
fsQoSSchedulerStatus RowStatus
}
fsQoSSchedulerId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Scheduler Identifier that uniquely identifies the
scheduler in the system/egress interface."
::= { fsQoSSchedulerEntry 1 }
fsQoSSchedulerSchedAlgorithm OBJECT-TYPE
SYNTAX INTEGER {
strictPriority(1),
roundRobin(2),
weightedRoundRobin(3),
weightedFairQueing(4),
strictRoundRobin(5),
strictWeightedRoundRobin(6),
strictWeightedFairQueing(7),
deficitRoundRobin(8)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Sets the packet scheduling algorithm for the port
The default is strictPriority(1)."
DEFVAL { 1 }
::= { fsQoSSchedulerEntry 2 }
fsQoSSchedulerShapeId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The shaper identifier that specifies the bandwidth requirements
for the scheduler. This object is not mandatory for the
creation of the conceptual row."
::= { fsQoSSchedulerEntry 3 }
fsQoSSchedulerHierarchyLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This indicates the depth of the queue/scheduler hierarchy.
A value of 0 indicates that there is no hierarchy and that all
queues/schedulers are port-bound.
0 - No hierarchy
1 - S1 schedulers (attached to the egress port)
2 - S2 schedulers (next level attached to the S1 schecdulers)
3 - S3 schedulers (attached to the COS queues)"
DEFVAL {0}
::= { fsQoSSchedulerEntry 4 }
fsQoSSchedulerGlobalId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Scheduler Identifier that uniquely identifies the
scheduler in the system/egress interface.This object is
used only for creating Scheduler entry from the
standard QOS Scheduler table diffServSchedulerTable
as defined in RFC 3289. The Id corresponds to the
diffServSchedulerId in RFC 3289. This is added purely
for the purpose of Save/Restore"
::= { fsQoSSchedulerEntry 5 }
fsQoSSchedulerStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "Row Status to Create/Destroy the entry.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSSchedulerEntry 6 }
-- ========================================================================== --
-- Hierarchy Table : for hierarchical queuing/scheduling --
-- ========================================================================== --
fsQoSHierarchyTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSHierarchyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Hierarchy table for specifying the hierarchy details."
::= { fsQoSTrafficMgmt 7 }
fsQoSHierarchyEntry OBJECT-TYPE
SYNTAX FsQoSHierarchyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Each entry specifies the queue/scheduler details to be used
for the next level hierarchy. The interface index associated with
the NextQ or Next Scheduler is obtained from this table index
- 'ifIndex'."
INDEX { ifIndex, fsQoSHierarchyLevel, fsQoSSchedulerId }
::= { fsQoSHierarchyTable 1 }
FsQoSHierarchyEntry ::=
SEQUENCE {
fsQoSHierarchyLevel Unsigned32,
fsQoSHierarchyQNext Unsigned32,
fsQoSHierarchySchedNext Unsigned32,
fsQoSHierarchyWeight Unsigned32,
fsQoSHierarchyPriority SchedulerPriority,
fsQoSHierarchyStatus RowStatus
}
fsQoSHierarchyLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..10)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This indicates the depth of the queue/scheduler hierarchy.
A value of 0 indicates that there is no hierarchy and that all
queues/schedulers are port-bound."
::= { fsQoSHierarchyEntry 1 }
fsQoSHierarchyQNext OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The output of this COSQ is sent to the scheduler attached to the queue.
For eg.,
A packet may flow from a cosq to the schedulers in the following way:
COSQ => S3 => S2 => S1 => Egress port.
The value of this object could be unique in the system/port.
A valid value is not mandatory for the creation of the conceptual row.
This object is used for hierarchical queuing."
::= { fsQoSHierarchyEntry 2 }
fsQoSHierarchySchedNext OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The next-level scheduler to which the scheduler output needs to
be sent. The value of this object could be unique in the system/port.
A valid value is not mandatory for the creation of the
conceptual row. This object is used for hierarchical scheduling."
::= { fsQoSHierarchyEntry 3 }
fsQoSHierarchyWeight OBJECT-TYPE
SYNTAX Unsigned32(0..1000)
UNITS "Percentage"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Weight is specified if the Scheduler is connecting to a WFQ of
another Scheduler. Agent returns Weight = 0 to represent that this
object is not configured by the manager."
::= { fsQoSHierarchyEntry 4 }
fsQoSHierarchyPriority OBJECT-TYPE
SYNTAX SchedulerPriority
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Scheduler can connect to any of the Priority of the next-level
Scheduler. The priority is specified when the scheduler is
connecting to any of the priorities ( EF, AF, BE) of the
next level strict-priority scheduler. A value of 0 indicates
that this value is not configured by manager."
DEFVAL { 0 }
::= { fsQoSHierarchyEntry 5 }
fsQoSHierarchyStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "Row Status to Create/Destroy the entry.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise return inconsistentValue error."
::= { fsQoSHierarchyEntry 6 }
-- ========================================================================== --
-- Default User Priority Table : for Untagged Packets --
-- and to specify preference for p-bit over dscp in case of tagged --
-- packets --
-- ========================================================================== --
fsQoSDefUserPriorityTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSDefUserPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table that contains default user priority for an interfae."
::= { fsQoSTrafficMgmt 8}
fsQoSDefUserPriorityEntry OBJECT-TYPE
SYNTAX FsQoSDefUserPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for configuring default user priority for each port. This is
used for assigning priority to the untagged packets received on the
interface."
INDEX { ifIndex }
::= { fsQoSDefUserPriorityTable 1 }
FsQoSDefUserPriorityEntry ::=
SEQUENCE {
fsQoSPortDefaultUserPriority Integer32,
fsQoSPortPbitPrefOverDscp INTEGER
}
fsQoSPortDefaultUserPriority OBJECT-TYPE
SYNTAX Integer32 (0..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default ingress user priority for this port.
It will be used to set priority for an untagged Packets."
::= { fsQoSDefUserPriorityEntry 1 }
fsQoSPortPbitPrefOverDscp OBJECT-TYPE
SYNTAX INTEGER { enabled(1), disabled(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default pbit precedence for a port over DSCP is enabled.
It will be used to set preferece as P-Bit over DSCP
for the given tagged port."
DEFVAL { enabled }
::= { fsQoSDefUserPriorityEntry 2 }
-- ========================================================================== --
-- Policer Statistics Counters --
-- ========================================================================== --
fsQoSPolicerStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSPolicerStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A list of Policer Statistics."
::= { fsQoSStats 1 }
fsQoSPolicerStatsEntry OBJECT-TYPE
SYNTAX FsQoSPolicerStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A collection of statistics kept for a particular Policer."
INDEX { fsQoSMeterId }
::= { fsQoSPolicerStatsTable 1 }
FsQoSPolicerStatsEntry ::=
SEQUENCE {
fsQoSPolicerStatsConformPkts Counter64,
fsQoSPolicerStatsConformOctets Counter64,
fsQoSPolicerStatsExceedPkts Counter64,
fsQoSPolicerStatsExceedOctets Counter64,
fsQoSPolicerStatsViolatePkts Counter64,
fsQoSPolicerStatsViolateOctets Counter64,
fsQoSPolicerStatsStatus EnableStatus,
fsQoSPolicerStatsClearCounter TruthValue
}
fsQoSPolicerStatsConformPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Packets marked down as conforming(Green) traffic
by this policer."
::= { fsQoSPolicerStatsEntry 1 }
fsQoSPolicerStatsConformOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Octets of traffic marked down as conforming(Green)
by this policer."
::= { fsQoSPolicerStatsEntry 2 }
fsQoSPolicerStatsExceedPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Packets marked down as exceeding(Yellow) traffic
by this policer."
::= { fsQoSPolicerStatsEntry 3 }
fsQoSPolicerStatsExceedOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Octets of traffic marked down as exceeding(Yellow)
by this policer."
::= { fsQoSPolicerStatsEntry 4 }
fsQoSPolicerStatsViolatePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Packets marked down as violating(Red) traffic
by this policer."
::= { fsQoSPolicerStatsEntry 5 }
fsQoSPolicerStatsViolateOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of Octets of traffic marked down as violating(Red)
by this policer."
::= { fsQoSPolicerStatsEntry 6 }
fsQoSPolicerStatsStatus OBJECT-TYPE
SYNTAX EnableStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Status indicating the Policer Statistics is being Enabled/Disabled
for the specific meter.
When statistics collection is set to disabled, stops collecting
statistics in this table.
When statistics collection is set to enabled, starts collecting
statistics in the table"
DEFVAL { disable }
::= {fsQoSPolicerStatsEntry 7 }
fsQoSPolicerStatsClearCounter OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" Resets all the counter variables to initialization value (zero)."
DEFVAL {false}
::= { fsQoSPolicerStatsEntry 8 }
-- ========================================================================== --
-- CoS based Statistics Counters --
-- ========================================================================== --
fsQoSCoSQStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSCoSQStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of class-of-service based Queue Statistics for a COS Queue."
::= { fsQoSStats 2 }
fsQoSCoSQStatsEntry OBJECT-TYPE
SYNTAX FsQoSCoSQStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of CoS Queue statistics for a particular COS queue."
INDEX { ifIndex, fsQoSCoSQId }
::= { fsQoSCoSQStatsTable 1 }
FsQoSCoSQStatsEntry ::=
SEQUENCE {
fsQoSCoSQId Unsigned32,
fsQoSCoSQStatsEnQPkts Counter64,
fsQoSCoSQStatsEnQBytes Counter64,
fsQoSCoSQStatsDeQPkts Counter64,
fsQoSCoSQStatsDeQBytes Counter64,
fsQoSCoSQStatsDiscardPkts Counter64,
fsQoSCoSQStatsDiscardBytes Counter64,
fsQoSCoSQStatsOccupancy Counter64,
fsQoSCoSQStatsCongMgntAlgoDrop Counter64
}
fsQoSCoSQId OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The COSQ for which the statistics is being collected."
::= { fsQoSCoSQStatsEntry 1 }
fsQoSCoSQStatsEnQPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of packets enqueued in this CoS Queue."
::= { fsQoSCoSQStatsEntry 2 }
fsQoSCoSQStatsEnQBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of bytes enqueued in this CoS Queue."
::= { fsQoSCoSQStatsEntry 3 }
fsQoSCoSQStatsDeQPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of packets de-queued from this CoS Queue."
::= { fsQoSCoSQStatsEntry 4 }
fsQoSCoSQStatsDeQBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of bytes de-queued from this CoS Queue."
::= { fsQoSCoSQStatsEntry 5 }
fsQoSCoSQStatsDiscardPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of packets discarded from this CoS Queue."
::= { fsQoSCoSQStatsEntry 6 }
fsQoSCoSQStatsDiscardBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of bytes discarded from this CoS Queue."
::= { fsQoSCoSQStatsEntry 7 }
fsQoSCoSQStatsOccupancy OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of bytes currently occupied in the CoS Queue."
::= { fsQoSCoSQStatsEntry 8 }
fsQoSCoSQStatsCongMgntAlgoDrop OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of bytes discarded due to congestion management
algorithm (RED/WRED) in this CoS Queue."
::= { fsQoSCoSQStatsEntry 9 }
-- Hardware CPU Rate Control Group
fsQosHwCpuRateLimitTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQosHwCpuRateLimitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table describing the queue parameters for CPU port"
::= { fsQosHwCpuRateControl 1 }
fsQosHwCpuRateLimitEntry OBJECT-TYPE
SYNTAX FsQosHwCpuRateLimitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION " CPU Rate Limit table entry"
INDEX {fsQosHwCpuQId }
::= { fsQosHwCpuRateLimitTable 1 }
FsQosHwCpuRateLimitEntry ::=
SEQUENCE {
fsQosHwCpuQId Unsigned32,
fsQosHwCpuMinRate Unsigned32,
fsQosHwCpuMaxRate Unsigned32,
fsQosHwCpuRowStatus RowStatus
}
fsQosHwCpuQId OBJECT-TYPE
SYNTAX Unsigned32 ( 1..65535 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Queue Identifier that uniquely identifies the queue
in the system/port."
::= { fsQosHwCpuRateLimitEntry 1 }
fsQosHwCpuMinRate OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls the minimum transmission rate
on a cpu port. Min Rate must be less than or equal
to Max Rate."
::= { fsQosHwCpuRateLimitEntry 2 }
fsQosHwCpuMaxRate OBJECT-TYPE
SYNTAX Unsigned32 ( 1..65535 )
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls the maximum transmission rate on
a cpu port. Max Rate must be greater than or equal to
Min Rate."
::= { fsQosHwCpuRateLimitEntry 3 }
fsQosHwCpuRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the status of this entry.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'."
::= { fsQosHwCpuRateLimitEntry 4 }
fsQoSVlanQueueingStatus OBJECT-TYPE
SYNTAX INTEGER { disabled(0), enabled(1) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to enable or disable Vlan Based Queueing
in the system. When set as 'enabled', QoS module programs the
hardware with the Hierarchical Scheduling Schema for Vlan based
queueing. When set as 'disabled', it removes the hardware
configuration."
DEFVAL { disabled }
::= { fsQoSSystem 6 }
-- ========================================================================== --
-- Vlan Map Table --
-- ========================================================================== --
fsQoSVlanMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSVlanMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies a table to map incoming VLAN to a specific subscriber queue of a port."
::= { fsQoSClass 4 }
fsQoSVlanMapEntry OBJECT-TYPE
SYNTAX FsQoSVlanMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies an entry to map an incoming VLAN to a specific
Subscriber Queue of an Egress PORT. The ifIndex
value should be of egress member port of the VLAN."
INDEX { fsQoSVlanMapID }
::= { fsQoSVlanMapTable 1 }
FsQoSVlanMapEntry ::=
SEQUENCE {
fsQoSVlanMapID IndexInteger,
fsQoSVlanMapIfIndex Unsigned32,
fsQoSVlanMapVlanId Unsigned32,
fsQoSVlanMapStatus RowStatus
}
fsQoSVlanMapID OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" This object specifies the output VLAN map index for the outgoing packets transmitted over
egress PORT with specified VLAN-id. This is unique for each entry in
the VLAN-map table."
::= { fsQoSVlanMapEntry 1 }
fsQoSVlanMapIfIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Egress Port Number. VLAN based subscriber Queuing/Scheduling
schema will be created on this port."
::= { fsQoSVlanMapEntry 2 }
fsQoSVlanMapVlanId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This object specifies the Vlan Id for Subscriber queue mapping. The Vlan Id should
already be configured on the switch."
::= { fsQoSVlanMapEntry 3 }
fsQoSVlanMapStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the status of this conceptual row. All writable objects in this
row may be modified at any time.
It can be deleted 'destroy', only if it is not referenced
by other table; otherwise returns inconsistentValue error.
For any mib table that supports global configurations (less-specific) at runtime
and H/W supports more-specific configurations, if a more-specific entry is deleted
by configuration, then the next less-specific entry gets programmed to H/W."
::= { fsQoSVlanMapEntry 4 }
-- ========================================================================== --
-- PCP MODEL SELECTION --
-- ========================================================================== --
fsQoSPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF FsQoSPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the table containing Qos related Properties specific to an interface.
Currently, we are using this table for storing Priority Code Point
encoding and decoding information."
::= { fsQoSClass 5 }
fsQoSPortEntry OBJECT-TYPE
SYNTAX FsQoSPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the information controlling per port configuration for Priority Code Point
Encoding and Decoding."
INDEX { ifIndex , fsQoSPcpPacketType}
::= { fsQoSPortTable 1 }
FsQoSPortEntry ::=
SEQUENCE {
fsQoSPcpPacketType INTEGER,
fsQoSPcpSelRow INTEGER,
fsQoSPcpRowStatus RowStatus
}
fsQoSPcpPacketType OBJECT-TYPE
SYNTAX INTEGER{
dot1P (0),
ip (1),
mpls (3)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the incoming packet type for which Priority Code Point
Encoding and decoding to be applied."
::= { fsQoSPortEntry 1 }
fsQoSPcpSelRow OBJECT-TYPE
SYNTAX INTEGER{
codePoint8P0D (1),
codePoint7P1D (2),
codePoint6P2D (3),
codePoint5P3D (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the row to be used on this port for PCP encoding and PCP decoding
tables. PCP encoding and PCP decoding on a port will be based on the row
configured as per this mib object for this port. This can be set for all
bride port types."
::= { fsQoSPortEntry 2 }
fsQoSPcpRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object spcifies the status of this entry.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'."
::= { fsQoSPortEntry 3 }
END
View Git Blame Copy Permalink