WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/adtran/ADTRAN-TAeSCU-MIB

3473 lines
137 KiB
Plaintext
Raw Permalink Blame History

ADTRAN-TAeSCU-MIB
DEFINITIONS ::= BEGIN
-- TITLE: The ADTRAN enhanced System Controller Unit MIB
-- PRODUCT: 1181018L1
-- VERSION: 2.13
-- DATE: 10/12/07
-- This MIB defines the object identifier (OID) for the Total Access
-- 3000 enhanced SCU. It also defines product specific objects.
-- MIBs supported:
-- MIB-2 (RFC1213)
-- Interface types (IANAifType - Internet Assigned Numbers Authority)
-- Interfaces (RFC2863)
-- ADTRAN standard (ADTRAN)
-- ADTRAN textual conventions (adtrantc)
-- ADTRAN generic chassis (genchass)
-- ADTRAN generic slot (genslot)
-- ADTRAN generic port (genport)
-- ADTRAN generic eSCU (genescu)
-- ADTRAN shelf specific OID MIB (adta3000, adta3010)
-- ADTRAN product specific eSCU 018 (adtaescu)
-- Proxy agent for SNMP access to all cards in TA3000 shelves.
-- adGenSlotFaceplate (genslot)
-- SCU 1181018L1 has single color LED
-- The SCU 1181018L1 returns a 4 byte string.
-- byte 1 FSE - Red fuse LED (always off) 00 off 01 on
-- byte 2 ALM - Red Alarm status LED 00 off 01 on
-- byte 3 HST - Green LED 00 Client 01 Host 00 off 01 on
-- byte 4 ACO - Green LED 00 off 01 on
-- LED byte position description
-- 1 2
-- 3 4
-- adGenSlotFaceplate (genslot)
-- SCU 1181018L2 has single color LED
-- The SCU 1181018L2 returns 7 byte string.
-- byte 1 PWR - Green LED (always on, green) 00 off 01 on
-- byte 2 ENET - Green Ethernet LINK status 00 off 01 on
-- byte 3 HOST - Green LED 00 Client 01 Host 00 off 01 on
-- byte 4 CRI - Red Alarm LED CRITICAL 00 off 01 on
-- byte 5 MAJ - Red Alarm LED MAJOR 00 off 01 on
-- byte 6 MIN - Red Alarm LED MINOR 00 off 01 on
-- byte 7 ACO - Green LED 00 off 01 on
-- adGenSlotAlarmStatus description
-- The various bit positions are:
-- ==========================================================================
-- Bit 1-16 scu alarm/status Byte 1 - 2 Details below->
-- Bit 17-136 Card per slot Remove alams Byte 3 - 17
-- Bit 137 - 256 Card fuse blown alarms for each slot Byte 18 - 32
-- =========================================================================
-- Bits Details for 1-16 scu alarm/status Byte 1 -2
-- ==========================================================================
-- bit 1 Indicate that a alarm is present on the SCU.
-- bit 2 "Indicates whether or not the alarm cut-off is on."
-- bit 3 "Indicates whether or not the alarm cut-off input is active."
-- bit 4 (adTAeSCUCtrpRmtAlm) "remote alarm input is active."
-- bit 5 (adTAeSCUCtrpExt1Alm) "external alarm input #1 is active."
-- bit 6 (adTAeSCUCtrpExt2Alm) "external alarm input #2 is active."
-- bit 7 (adTAeSCUCtrpBusApowerAlm) "Iminus 48V power supply A is active."
-- bit 8 (adTAeSCUCtrpBusBpowerAlm) "minus 48V power supply B is active."
-- bit 9 Device comm failure. This is not a SNMP alarm.
-- bit 10 "Indicates whether one or more card fuses on this chassis is open."
-- bit 11 adTAeSCUCraftLoginNotfication
-- bit 12 adTAPowerSheddingInputAsserted
-- bit 13 adTAPowerSheddingActivated
-- bit 14 Empty
-- bit 15 Empty
-- bit 16 Empty
-- ==========================================================================
-- Bits Detail 17-56 Card slot blown fuses 4 bytes
-- ==========================================================================
-- Bits 17-24 for slot 8 - 1 card blown fuse alarm status byte 3
-- Bits 25-32 for slot 16 - 9 card blown fuse status byte 4
-- Bits 33-40 for slot 24 - 17 card blown fuse status byte 5
-- Bits 41-48 for slot 32 - 25 card blown fuse status byte 6
-- Bits 49-56 Empty
-- ==========================================================================
-- Bits 57-56 Empty
-- ==========================================================================
-- Bits 58 adTACriticalAudibleRelayActive
-- Bits 59 adTACriticalVisualRelayActive
-- Bits 60 adTAMajAudibleRelayActive
-- Bits 61 adTAMajVisualRelayActive
-- Bits 62 adTAMinorAudibleRelayActive
-- Bits 63 adTAMinorVisualRelayActive
-- Bits 64 adTAAux1RelayActive
-- Bits 65 adTAAux2RelayActive
-- ...
-- Bits 129-136 slot 112 - 113 scu blown fuse byte 17
-- ==========================================================================
-- Bits Detail 137-256 represents card remove alarm present 15 bytes
-- ==========================================================================
-- Bits 137-144 for slot 8 - 1 card remove alarm status byte 18
-- Bits 145-152 for slot 16 - 9 card remove alarm status byte 19
-- Bits 153-160 for slot 24 - 17 card remove alarm status byte 20
-- Bits 161-168 for slot 32 - 25 card remove alarm status byte 21
-- ...
-- Bits 249-256 for slot 120 - 113 card remove alarm status byte 32
-- HISTORY:
-- 14/11/01 pnb First edition.
-- 03/05/01 pnb ad Boot Version object to this MIB for ATP.
-- 01/22/02 ap Added SNMP security account management support
-- 06/13/02 ap Add Software Configuration Archive, DNS, System Log, and
-- other support OIDs changes.
-- 06/14/02 RJF Change 'adTAeScuFirmwareTftpServerHostName' from read-only to read-write
-- 06/28/02 ap add adTAeScuSCAAutoSave and adTAeScuSCAAutoSaveRetries and remove adTAeScuSCAAutoSaveInterval
-- 07/23/02 ap Ver 2.0 MIB changes to work with SCU versions C00.18 and above:
--- Add objects adTAeSCUDefaultRouteInterfaceEx, adTAeSCUIpForwarding, adTAeSCURestoreNetProvFromMUX,
--- adTAESCUSecChangeAccountPassword and the following tables and groups:
--- Network Management Group adTAeSCUNetworkMgmt
--- DNS related managment adTAeSCUsDNS
--- Sofware/Config through TFTP adTAeSCUFirmwareTFTPConfigMgmt
--- SCA () Sofware/Config related dids adTAeSCUSystemConfigArchiveMgmt
--- SCA Auto Save Management adTAeSCUSCAControl
--- SCA Status table adTAeSCUSCAOperationStatusTable
--- SCA Auto Save Management adTAeSCUSCAAutoSaveMgmt
--- SCA Restore Management adTAeSCUSCARestoreMgmt
--- System Log group adTAeSCUSystemLog
-- 08/05/02 ap Add integer limit to adTAeScuSCAAutoSaveHoursAfter and adTAeScuSCAAutoSaveMinutesAfter.
-- 21/02/03 ap Change trap level NORMAL to INFORMATIONAL
-- 08/15/03 ap Add support adTAeScuFirmwareTftpCacheExpire and adTAeScuFirmwareTftpInvalidate
-- 03/11/03 ap Add adGenSlotAlarmStatus description
-- adGenSlotAlarmStatus description
-- The various bit positions are:
-- ==========================================================================
-- Bit 1-16 scu alarm/status Byte 1 - 2 Details below->
-- Bit 17-136 Card per slot Remove alams Byte 3 - 17
-- Bit 137 - 256 Card fuse blown alarms for each slot Byte 18 - 32
-- =========================================================================
-- Bits Details for 1-16 scu alarm/status Byte 1 -2
-- ==========================================================================
-- bit 1 Indicate that a alarm is present on the SCU.
-- bit 2 "Indicates whether or not the alarm cut-off is on."
-- bit 3 "Indicates whether or not the alarm cut-off input is active."
-- bit 4 (adTAeSCUCtrpRmtAlm) "remote alarm input is active."
-- bit 5 (adTAeSCUCtrpExt1Alm) "external alarm input #1 is active."
-- bit 6 (adTAeSCUCtrpExt2Alm) "external alarm input #2 is active."
-- bit 7 (adTAeSCUCtrpBusApowerAlm) "Iminus 48V power supply A is active."
-- bit 8 (adTAeSCUCtrpBusBpowerAlm) "minus 48V power supply B is active."
-- bit 9 Device comm failure. This is not a SNMP alarm.
-- bit 10 "Indicates whether one or more card fuses on this chassis is open."
-- bit 11 to 16 Nothing (Empty)
-- ==========================================================================
-- Bits Detail 17-136 Card slot blown fuses 15 bytes
-- ==========================================================================
-- Bits 17-24 for slot 8 - 1 card blown fuse alarm status byte 3
-- Bits 25-32 for slot 16 - 9 card blown fuse status byte 4
-- Bits 33-40 for slot 24 - 17 card blown fuse status byte 5
-- Bits 41-48 for slot 32 - 25 card blown fuse status byte 6
-- ...
-- Bits 129-136 slot 112 - 113 scu blown fuse byte 17
-- ==========================================================================
-- Bits Detail 137-256 represents card remove alarm present 15 bytes
-- ==========================================================================
-- Bits 137-144 for slot 8 - 1 card remove alarm status byte 18
-- Bits 145-152 for slot 16 - 9 card remove alarm status byte 19
-- Bits 153-160 for slot 24 - 17 card remove alarm status byte 20
-- Bits 161-168 for slot 32 - 25 card remove alarm status byte 21
-- ...
-- Bits 249-256 for slot 120 - 113 card remove alarm status byte 32
-- ==========================================================================
-- ==========================================================================
-- 09/11/03 AP Add configAccess(7) to adTAeSCUSecAccountAccessRights.
-- 10/20/03 AP fix syntax error on line 472.
-- 01/19/04 AP Add accessoryOption(4) to adTAeSCUNetworkMgmtPortComMode
-- 01/29/04 AP For SCA OIDs DB0 corresponds to the Accessory Slot. (Comment change)
-- 04/15/04 AP Add adTAeScuTL1ActivityLog
-- 12/28/04 AP Add password complexity, Add Account and Password aging, Add RADIUS login options
-- 04/20/05 AP Add adTAeTrustedClientAccessControl
-- 10/20/05 AP Add adTAeSCUCraftLoginNotfication
-- 02/03/06 KMM Additional changes made while adding support for packed
-- sstate msgs. Added:
-- *) service state set single fail
-- *) service state get single fail
-- *) service state set all fail
-- *) service state get all fail
-- 04/03/06 KMM Removed alarms added on 02/03/06. These are auto-clearing alarms, therefore
-- do not have alarm status.
-- 05/09/06 JMC Added power shedding bit definitions to commments.
-- Standardized last section of these comments, it was ugly!
-- 10/05/06 MAS Added support for MII Ethernet and ENET interface
-- 07/11/07 AP Fix adTAeSCUSystemLogEntry index. Add (adTAeSCUSystemLogIndex).
-- 08/29/07 AP Add adTAeSCUSecLastSixPasswordCheck and adTAeSCUSecPasswordStartEndDigitCheck
-- 09/24/07 AP Add adTAeSCUSecLoginStatTable.
-- 10/12/07 AP Add adTAeScuRADIUSFallbackMode
-- 11/01/07 AP Change adTAeSCUNetworkMgmtPortBaudRate description.
-- 11/12/07 KABC Added adTAeSCUSecAccountConnectionPort and adTAeSCUSecAccountDisconnectSession
-- 11/13/07 KABC Added Account Lock-out Settings Section:
-- adTAeScuEnableAccLoginFailureLockOut, adTAeScuEnableLockOutAlarm,
-- adTAeScuEnableIndefLockOut, adTAeScuNumLockOutLoginAttempts,
-- and adTAeScuLockOutDuration
-- 11/16/07 KABC Added adTAeSCUSecChallengeKey, adTAeSCUSecMultiLoginAcct,and adTAeSCUSecRemoteMenuAccessRequired
-- 11/27/07 KABC Changed adTAeSCUSecAccountDisconnectSession to read-write from read-only
-- 01/21/08 BKP Added osiTunnel(4), pppDCC0(5), and ethernet2(6) enum values to the adTAeSCUDefaultRouteInterfaceEx OID that I don't see any EMS support
-- for the OPTI, 5K, or 3K.
-- 01/28/08 BKP Added SNMP support for the Mount Location and the Interbank Communication Mode.
-- Also added adTAeSCUNetworkMgmtInterbankComModeWritable, adTAeSCULogoffCraftDTRLoss, and adTAeSCUMinMenuRefresh.
-- 02/01/08 BKP Removed SNMP support for the Mount Location.
-- 02/12/08 AP Fix adTAeSCUSystemLogIndex to be a table OID.
-- 03/06/08 KABC Added adTAeScuSCASlotsInSCA, adTAeScuSCASlotsWithProvDataInSCA, and adTAeScuSCADateTimeNextAutoSave
-- 03/07/08 KABC Added adTAeScuSCACardsRestoredBitmask, adTAeScuSCACardsNotRestoredBitmask, adTAeScuSCACardsExcludedBitmask,
-- and adTAeScuSCARestoreCardErrorsBitmask
-- 04/14/08 PEW Added adTAeSCUSysTACACSPlusConfig (TACACS+ Configuration)
-- 04/24/08 AP Add adTAeSCUSecAccountAuthenticationMethod
-- 05/14/08 AP Add adTAeSCUSystemLogFailureDescription
-- 10/31/08 AP Add adTAeScuTACACSPlusServerPort
-- 01/29/09 KABC Added adTAeSCUSecForcePasswordReset
-- 02/04/09 KABC Added adTAeSCUNetworkMgmtSecurityEnable
-- 05/05/09 AP Convert to SNMPv2
-- 08/07/09 KABC Added adTAeSUSecSendAcctExpAlarm, adTAeSCUSecResetAllAccountAge, and
-- adTAeSCUSecResetAllPasswordAge
-- 08/12/09 KABC Added adTAeScuTACACSPlusServerName and adTAeScuTACACSPlusServerSequence
-- 04/08/09 AP Add adTAeSCUSecLastSessionType, adTAeSCUSecLastConnectionType, and adTAeSCUSecLastIPAddress
--
-- Operational notes
-- When the SCU is addressed by IP address with scalar objects, it usually replies
-- as a proxy for the shelf in which it is contained, providing MIB-2 system group
-- support and ADTRAN.MIB object support. To address information on specific cards,
-- card/port selection can be done via the ADTRAN generic MIBs, or internet standard
-- MIBs that are indexed by ifIndex. Mapping between these indexing methods is provided
-- in the genport MIB.
--
-- The exception to scalars being processed directely by the SCU are those in Internet
-- standard MIBs that are specially identified to belong to a Multiplexor, and for which
-- special provision has been made to direct these anonymous requests to the appropriate
-- Mux. Otherwise scalars are not supported on line cards as there is no way to select which
-- card is the intended target.
IMPORTS
OBJECT-TYPE,
NOTIFICATION-TYPE,
MODULE-IDENTITY,
OBJECT-IDENTITY,
Integer32,
IpAddress
FROM SNMPv2-SMI
DisplayString
FROM SNMPv2-TC
sysName
FROM SNMPv2-MIB
adProducts,
adMgmt
FROM ADTRAN-MIB
adGenSlotInfoIndex
FROM ADTRAN-GENSLOT-MIB
adTrapInformSeqNum
FROM ADTRAN-GENTRAPINFORM-MIB
InetAddress,
InetAddressType
FROM INET-ADDRESS-MIB
;
adTAeSCUmg MODULE-IDENTITY
LAST-UPDATED "201612090000Z"
ORGANIZATION "Adtran, Inc."
CONTACT-INFO
"CND Tech Support
Postal: ADTRAN, Inc.
901 Explorer Blvd.
Huntsville, AL 35806
Tel: +1 800 726-8663
Fax: +1 256 963 6217
E-mail: support@adtran.com"
DESCRIPTION
"This MIB defines the objects for the adtranTAeScuMib MIB."
REVISION "201612070000Z"
DESCRIPTION "Add InetAddress OIDs to support IPv4/IPv6 addresses for Trusted Access List Clients."
REVISION "201609200000Z"
DESCRIPTION "Add the RadiusServerSequence and RadiusName OIDs for Radius servers."
REVISION "201606130000Z"
DESCRIPTION "Add support IPV6 address for SCM servers."
REVISION "201406100000Z"
DESCRIPTION "Added Bulk Data Export OID for the path."
REVISION "201208141300Z"
DESCRIPTION "Added cLI(5) to adTAeSCUNetworkMgmtPortComMode.
Add adTAeTrustedIPClientAccessName Trusted IP Access-list name.
Deleted all Trusted IP Clients when set to an empty string."
REVISION "201207120000Z"
DESCRIPTION "Added Bulk Data Export OID for the port number."
REVISION "201204231600Z"
DESCRIPTION "Add adTAeSCUSystemLogFailureDescription varbind to adTAeSCUSystemLogFailure NOTIFICATION-TYPE."
REVISION "201106270000Z"
DESCRIPTION "Added four OIDs for Bulk Data Export."
REVISION "200705010000Z"
DESCRIPTION "Converted from SNMPv1 adTAeSCU.mib file."
::= { adMgmt 241 }
-- OBJECT IDENTIFIERS
adTAeSCU OBJECT IDENTIFIER ::= { adProducts 241 }
--adTAeSCUmg OBJECT IDENTIFIER ::= { adMgmt 241 }
--
-- Configuration Information
--
adTAeSCUConfig OBJECT IDENTIFIER
::= { adTAeSCUmg 1 }
adTAeSCUConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The enhanced System Controller Unit Config table."
::= { adTAeSCUConfig 1 }
adTAeSCUConfigEntry OBJECT-TYPE
SYNTAX AdTAeSCUConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the eSCU Config table."
INDEX { adGenSlotInfoIndex }
::= { adTAeSCUConfigTable 1 }
AdTAeSCUConfigEntry ::=
SEQUENCE {
adTAeSCUBootVersion
DisplayString
}
adTAeSCUBootVersion OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Firmware version of the boot ROM."
::= { adTAeSCUConfigEntry 1 }
--
-- Card Provisioning Information
--
adTAeSCUCardProv OBJECT IDENTIFIER
::= { adTAeSCUmg 2 }
adTAeSCUCardProvTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUCardProvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The enhanced System Controller Unit's
(eSCU's) card-level provisioning table."
::= { adTAeSCUCardProv 1 }
adTAeSCUCardProvEntry OBJECT-TYPE
SYNTAX AdTAeSCUCardProvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the enhanced System Controller
Unit's (eSCU's) card-level provisioning table."
INDEX { adGenSlotInfoIndex }
::= { adTAeSCUCardProvTable 1 }
AdTAeSCUCardProvEntry ::=
SEQUENCE {
adTAeSCUDefaultRouteInterface
INTEGER,
adTAeSCUIpForwarding
INTEGER,
adTAeSCURestoreNetProvFromMUX
INTEGER,
adTAeSCUDefaultRouteInterfaceEx
INTEGER,
adTAeSCULogoffCraftDTRLoss
INTEGER,
adTAeSCUMinMenuRefresh
INTEGER
}
adTAeSCUDefaultRouteInterface OBJECT-TYPE
SYNTAX INTEGER {
ethernet(1),
in-band(2)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Default Route Interface to be used by
the Controller."
::= { adTAeSCUCardProvEntry 1 }
adTAeSCUIpForwarding OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Determines wether the eSCU will perform IP forwarding."
::= { adTAeSCUCardProvEntry 2 }
adTAeSCURestoreNetProvFromMUX OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This setting determines whether or not the eSCU will attempt to
restore its IP network interface settings from the online MUX.
These settings will be restored only if the eSCU has been removed
and another eSCU inserted in it place without removal or reset
of the online MUX.."
::= { adTAeSCUCardProvEntry 3}
adTAeSCUDefaultRouteInterfaceEx OBJECT-TYPE
SYNTAX INTEGER {
ethernet(1),
in-band(2),
local-PPP(3),
osiTunnel(4),
pppDCC0(5),
ethernet2(6),
none(999)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Same as adTAeSCUDefaultRouteInterface but added local-PPP(3), osiTunnel(4),
pppDCC0(5), ethernet2(6), and none(999). Default Route Interface to be used by
the Controller."
::= { adTAeSCUCardProvEntry 4 }
adTAeSCULogoffCraftDTRLoss OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When the Data Terminal Ready(DTR) signal from the connected terminal is lost,
the controller can automatically disable the port connection."
::= { adTAeSCUCardProvEntry 5 }
adTAeSCUMinMenuRefresh OBJECT-TYPE
SYNTAX INTEGER {
normal(1),
seconds1(2),
seconds5(3),
seconds15(4),
seconds60(5),
never(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum terminal menu refresh rate used to limit the frequency of menu refreshing."
::= { adTAeSCUCardProvEntry 6 }
--
-- Interface Status Information
--
adTAeSCUInterfaceStatus OBJECT IDENTIFIER
::= { adTAeSCUmg 4 }
adTAeSCUInterfaceStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUInterfaceStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The controller's interface-level status
table."
::= { adTAeSCUInterfaceStatus 1 }
adTAeSCUInterfaceStatusEntry OBJECT-TYPE
SYNTAX AdTAeSCUInterfaceStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the controller's interface-level
status table."
INDEX { adTAeSCUIfNumber }
::= { adTAeSCUInterfaceStatusTable 1 }
AdTAeSCUInterfaceStatusEntry ::=
SEQUENCE {
adTAeSCUIfNumber
Integer32,
adTAeSCUIfIndex
Integer32,
adTAeSCUIfIPAddress
IpAddress,
adTAeSCUIfSubnetMask
IpAddress,
adTAeSCUIfDefaultGateway
IpAddress,
adTAeSCUIfSpeed
INTEGER,
adTAeSCUIfXoverCorrection
INTEGER,
adTAeSCUIfLEDmode
INTEGER,
adTAeSCUIfLinkStatus
INTEGER,
adTAeSCUIfLinkRate
INTEGER
}
adTAeSCUIfNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interface Number assigned by the
Controller to it's interfaces. It is used to
index this table. It may or may not be equal
to the corresponding IfIndex."
::= { adTAeSCUInterfaceStatusEntry 1 }
adTAeSCUIfIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value is equal to the corresponding
IfIndex for each interface."
::= { adTAeSCUInterfaceStatusEntry 2 }
adTAeSCUIfIPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP Address assigned to this interface,
if any."
::= { adTAeSCUInterfaceStatusEntry 3 }
adTAeSCUIfSubnetMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Subnet Mask assigned to this interface,
if any."
::= { adTAeSCUInterfaceStatusEntry 4 }
adTAeSCUIfDefaultGateway OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Default Gateway assigned to this interface,
if any."
::= { adTAeSCUInterfaceStatusEntry 5 }
adTAeSCUIfSpeed OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
bt-10(2),
bt-100(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Ethernet interface data rate"
::= { adTAeSCUInterfaceStatusEntry 6 }
adTAeSCUIfXoverCorrection OBJECT-TYPE
SYNTAX INTEGER {
auto(1),
straight(2),
crossover(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Ethernet interface cable crossover correction"
::= { adTAeSCUInterfaceStatusEntry 7 }
adTAeSCUIfLEDmode OBJECT-TYPE
SYNTAX INTEGER {
link(1),
blinkactivity(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Ethernet interface LED operation, on for link
active only, or blink with link activity"
::= { adTAeSCUInterfaceStatusEntry 8 }
adTAeSCUIfLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
down(1),
up(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Ethernet interface physical layer (PHY) link
status"
::= { adTAeSCUInterfaceStatusEntry 9 }
adTAeSCUIfLinkRate OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
half-duplex-10bt(2),
half-duplex-100bt(3),
full-duplex-10bt(4),
full-duplex-100bt(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Ethernet interface link rate and duplex mode as
determined by the hardware"
::= { adTAeSCUInterfaceStatusEntry 10 }
--
--
--
--
--
--
--
--
--
--
-- Security Account Provisioning group
--
--
--
adTAeSCUSecurityAccountMg OBJECT IDENTIFIER
::= { adTAeSCUmg 5 }
adTAeSCUSecurityAccountEnabled OBJECT-TYPE
SYNTAX INTEGER {
scuSNMPSecurityManagementEnabled(1),
scuSNMPSecurityManagementDisabled(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This indicates if SNMP security management is enabled or
disabled. To enable SNMP security management go to menus
System Controller->Provisioning->General->Security Administration
using an ADMIN level account. All security SNMP object
will not respond until this object is enabled."
::= { adTAeSCUSecurityAccountMg 1 }
adTAeSCUSecuritySnmpAccountMgEnableDisable OBJECT-TYPE
SYNTAX DisplayString (SIZE(5..255))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable SNMP Access to security management.
Set a formatted string with [command] [backslash] [local ADMIN_account_name][backslash] [password].
Command : 1 for Enable SNMP Access to security management.
Command : 2 for Disable SNMP Access to security management.
Example:
Enable Access : 1\my_Admin_account\my_Password
Disable access: 2\my_Admin_account\my_Password"
::= { adTAeSCUSecurityAccountMg 7 }
adTAeSCUSecAccountAuthenticationMethod OBJECT-TYPE
SYNTAX INTEGER {
local (1),
rADIUS (2),
rADIUSorLocal (3),
tACACS (4),
tACACSorLocal (5),
tACACSorRADIUS (6),
tACACSorRADIUSorLOCAL (7)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The authentication method use to login to the controller.
If authentication failure occours, no other method will be used.
If access is granted, no other method will be used.
Selection with multiple methods will be used in the following maner:
tACACSorRADIUSorLocal
If TACACS server does not respond, the RADIUS server will be used.
If the RADIUS server does not respond then the Local accounts
will be used.
tACACSorRADIUS
If TACACS server does not respond, the RADIUS server will be used.
If the RADIUS server does not respond the controller will issue a
authentication failure.
tACACSorLocal
If TACACS server does not respond, then Local accounts will be used.
rADIUSorLocal
If RADIUS server does not respond, then Local accounts will be used.
tACACS
Login with TACACS server only.
rADIUS
Login with RADIUS server only.
local
Login with Local accounts only.
This method list will traverse the methods from TACACS+ to RADIUS,
and from RADIUS to the local security account database. Each of
these methods, including Local, will have the ability to be disabled,
thus allowing a configurable method list of the following iterations:
T (TACACS) R (RADIUS) L(LOCAL)
TRL, TR, TL, RL, T, R, L. A tech-support GR815 compliant
EEP (Challenge Key method) is still accepted for access into the
device regardless of the method list configuration (see example of
EEP in 61187010L1-5B, Figure 25, p.66). "
::= { adTAeSCUSecurityAccountMg 8 }
adTAeSCUSecAgingGlobalSettings OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 2 }
adTAeSCUSecAllAccountExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all security accounts expiration timer to value."
::= { adTAeSCUSecAgingGlobalSettings 1 }
adTAeSCUSecReadOnlyAccountExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"READONLY accounts expiration timer."
::= { adTAeSCUSecAgingGlobalSettings 2 }
adTAeSCUSecReadWriteAccountExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all READWRITEaccounts expiration timer settings value."
::= { adTAeSCUSecAgingGlobalSettings 3 }
adTAeSCUSecTestAccountExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all TEST accounts age."
::= { adTAeSCUSecAgingGlobalSettings 4 }
adTAeSCUSecConfigAccountExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all CONFIG expiration timer."
::= { adTAeSCUSecAgingGlobalSettings 5 }
adTAeSCUSecAdminAccountExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all ADMIN expiration timer."
::= { adTAeSCUSecAgingGlobalSettings 6 }
adTAeSCUSecSendAcctExpAlarm OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Send Inactive Accounts Alarm Enable."
::= { adTAeSCUSecAgingGlobalSettings 7 }
adTAeSCUSecResetAllAccountAge OBJECT-TYPE
SYNTAX INTEGER {
reset(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Resets all account expiration timers to zero."
::= { adTAeSCUSecAgingGlobalSettings 8 }
adTAeSCUSecAllPasswordExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all security password age set value."
::= { adTAeSCUSecAgingGlobalSettings 10 }
adTAeSCUSecReadOnlyPasswordExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all security READONLY accounts password expiration timer."
::= { adTAeSCUSecAgingGlobalSettings 11 }
adTAeSCUSecReadWritePasswordExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all READWRITE accounts password expiration timer settings value."
::= { adTAeSCUSecAgingGlobalSettings 12 }
adTAeSCUSecTestPasswordExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all TEST accounts password expiration timer."
::= { adTAeSCUSecAgingGlobalSettings 13 }
adTAeSCUSecConfigPasswordExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all CONFIG accounts password expiration timer."
::= { adTAeSCUSecAgingGlobalSettings 14 }
adTAeSCUSecAdminPasswordExpirationTimer OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all ADMIN accounts password expiration timer."
::= { adTAeSCUSecAgingGlobalSettings 15 }
adTAeSCUSecPasswordExpirationWarning OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Notification to users requiring them to change their passwords.
Number of days prior to expiration to display warning menu."
::= { adTAeSCUSecAgingGlobalSettings 20 }
adTAeSCUSecResetAllPasswordAge OBJECT-TYPE
SYNTAX INTEGER {
reset(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Resets all password expiration timers to zero."
::= { adTAeSCUSecAgingGlobalSettings 21 }
--
--
adTAeSCUAccountExpirationEnabled OBJECT-TYPE
SYNTAX INTEGER {
accountExpirationEnabled(1),
accountExpirationDisabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable account expiration for accounts."
::= { adTAeSCUSecurityAccountMg 5 }
adTAeSCUPasswordAgingEnabled OBJECT-TYPE
SYNTAX INTEGER {
passwordAgingEnabled(1),
passwordAgingDisabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable password aging."
::= { adTAeSCUSecurityAccountMg 6 }
--
--
--
adTAeSCUSecAccountTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUSecAccountEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SCU Security Account table."
::= { adTAeSCUSecurityAccountMg 3 }
adTAeSCUSecAccountEntry OBJECT-TYPE
SYNTAX AdTAeSCUSecAccountEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SCU Security Account table.
Writeable objects cannot be changed while adTAeSCUSecNumAccountLogin is 1 or more."
INDEX { adTAeSCUSecAccountIndex}
::= { adTAeSCUSecAccountTable 1 }
AdTAeSCUSecAccountEntry ::=
SEQUENCE {
adTAeSCUSecAccountIndex
Integer32,
adTAeSCUSecAccountUserID
DisplayString,
adTAeSCUSecAccountStatus
INTEGER,
adTAeSCUSecNumAccountLogin
Integer32,
adTAeSCUSecAccountAccessRights
INTEGER,
adTAESCUSecChangeAccountPassword
DisplayString,
adTAeSCUSecAccStatusExt
INTEGER,
adTAeSCUSecAccExpTime
Integer32,
adTAeSCUSecAccPasswordExpTime
Integer32,
adTAeSCUSecAccountAge
Integer32,
adTAeSCUSecAccPasswordAge
Integer32,
adTAeSCUSecResetAccountAge
INTEGER,
adTAeSCUSecResetAccPasswordAge
INTEGER,
adTAeSCUAccExpirationEnabled
INTEGER,
adTAeSCUAccPasswordAccAgingEnabled
INTEGER,
adTAeSCUSecForcePasswordReset
INTEGER
}
adTAeSCUSecAccountIndex OBJECT-TYPE
SYNTAX Integer32 (1..16)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Security account user Index."
::= { adTAeSCUSecAccountEntry 1 }
adTAeSCUSecAccountUserID OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Security account user ID name. If account
name is zero length (empty) then an account
name can be set. Setting a userID name
creates an account with default properties.
Account names cannot be changed. To change
an account name, the account first have
to be deleted by setting adTAeSCUSecNumAccountLogin
to deleted. Then set to the desired name.
All attempts to change an account name will
generate a bad value error."
::= { adTAeSCUSecAccountEntry 2 }
adTAeSCUSecAccountStatus OBJECT-TYPE
SYNTAX INTEGER {
createdEnabled(1), -- This account is created and enabled
createdDisabled(2), -- This account is created but is disabled. Cannot use this account to login.
deleted(3) -- This account does not exist. It is deleted.
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Status of the account. AdTAeSCUSecAccountStatus
cannot be changed while number of
adTAeSCUSecNumAccountLogin is one or more."
DEFVAL { deleted }
::= { adTAeSCUSecAccountEntry 3 }
adTAeSCUSecNumAccountLogin OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of current logins using this account.
Logged in status of account."
::= { adTAeSCUSecAccountEntry 4 }
adTAeSCUSecAccountAccessRights OBJECT-TYPE
SYNTAX INTEGER{
readOnlyAccess(1), -- Read Only Access.
readWriteAccess(2), -- Read and Write Access.
testAccess(3), -- Read, Write, and Test Access.
adminAccess(4), -- Read, Write, Test, and ADMIN Access.
fronPanelAccess(5), -- Front Panel Access only.
-- Can only login through the front panel.
-- Only for built in account. Cannot set this value.
techSupportAccess(6), -- Tech Support Access. Cannot set to this value.
configAccess(7) -- Read and Write Access to all items except for system
-- administration items.
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Access rights of account."
::= { adTAeSCUSecAccountEntry 5 }
-- adTAESCUSecAccountPassword OBJECT-TYPE
-- SYNTAX DisplayString (SIZE(0..16))
-- MAX-ACCESS read-write
-- STATUS obsolete
-- DESCRIPTION
-- "Account password. A password is a 16 character
-- alphanumeric word. Passwords cannot be viewed.
-- All passwords will be displayed as ******. "
-- DEFVAL { "*********" }
-- ::= { adTAeSCUSecAccountEntry 6 }
adTAESCUSecChangeAccountPassword OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..33))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Used to change account password. This string must contain the
old password and the new password separated by a \ (backslash) character.
Example: password\newpassword
A password is a 16 character
alphanumeric word. Passwords cannot be viewed.
All passwords will be displayed as ******.
A valid password may contain printable characters except for
the following characters: Backslash \, Single quote ', Blank space ."
DEFVAL { "********" }
::= { adTAeSCUSecAccountEntry 7 }
adTAeSCUSecAccStatusExt OBJECT-TYPE
SYNTAX INTEGER {
deleted(1), -- This account does not exist. It is deleted.
enabled(2), -- This account is created and enabled
disabled(3), -- This account is created but is disabled. Cannot use this account to login.
enabledExpired(4), -- This account is created, Enabled, and Expired. Cannot use this account to login.
disabledExpired(5), -- This account is created, Disabled, and Expired. Cannot use this account to login.
enabledLocked(6), -- This account is created, Enabled, and Locked. Cannot use this account to login.
disabledLocked(7), -- This account is created, Disabled, and locked. Cannot use this account to login.
enabledExpiredLocked(8), -- This account is created, Enabled, Expired, and Locked. Cannot use this account to login.
disabledExpiredLocked(9) -- This account is created, Disabled, Expired, and Locked. Cannot use this account to login.
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Status of the account. AdTAeSCUSecAccountStatus
cannot be changed while number of
adTAeSCUSecNumAccountLogin is one or more."
DEFVAL { deleted }
::= { adTAeSCUSecAccountEntry 8 }
adTAeSCUSecAccExpTime OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Security account expiration time."
::= { adTAeSCUSecAccountEntry 9 }
adTAeSCUSecAccPasswordExpTime OBJECT-TYPE
SYNTAX Integer32 (20..365)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Security account password expiration time."
::= { adTAeSCUSecAccountEntry 10 }
adTAeSCUSecAccountAge OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Security account age."
::= { adTAeSCUSecAccountEntry 11 }
adTAeSCUSecAccPasswordAge OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Security account password age."
::= { adTAeSCUSecAccountEntry 12 }
adTAeSCUSecResetAccountAge OBJECT-TYPE
SYNTAX INTEGER {
resetAccountAge(1) -- Reset Account Age to zero
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Reset security account age."
::= { adTAeSCUSecAccountEntry 13 }
adTAeSCUSecResetAccPasswordAge OBJECT-TYPE
SYNTAX INTEGER {
resetPasswordAge(1) -- Reset Password Age to zero
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Reset security account password age."
::= { adTAeSCUSecAccountEntry 14 }
adTAeSCUAccExpirationEnabled OBJECT-TYPE
SYNTAX INTEGER {
accountExpirationEnabled(1),
accountExpirationDisabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable single account expiration."
::= { adTAeSCUSecAccountEntry 15 }
adTAeSCUAccPasswordAccAgingEnabled OBJECT-TYPE
SYNTAX INTEGER {
passwordAgingEnabled(1),
passwordAgingDisabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable single account password aging."
::= { adTAeSCUSecAccountEntry 16 }
adTAeSCUSecForcePasswordReset OBJECT-TYPE
SYNTAX INTEGER {
forcedreset(1),
clearforcedreset(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Forces user to reset their password upon next login."
::= { adTAeSCUSecAccountEntry 17 }
--
-- Security Account Provisioning group
--
adTAeSCUSecAccountLoggedInTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUSecAccountLoggedInEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SCU Security Account table."
::= { adTAeSCUSecurityAccountMg 4 }
adTAeSCUSecAccountLoggedInEntry OBJECT-TYPE
SYNTAX AdTAeSCUSecAccountLoggedInEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SCU Security Account table."
INDEX { adTAeSCUSecAccountloginIndex}
::= { adTAeSCUSecAccountLoggedInTable 1 }
AdTAeSCUSecAccountLoggedInEntry ::=
SEQUENCE {
adTAeSCUSecAccountloginIndex
Integer32,
adTAeSCUSecAccountLoginUserIDIndex
Integer32,
adTAeSCUSecAccountLoginUserID
DisplayString,
adTAeSCUSecAccountConnectionType
INTEGER,
adTAeSCUSecAccountSessionType
INTEGER,
adTAeSCUSecAccountLoginConnectionSource
DisplayString,
adTAeSCUSecAccountLoginDateTime
DisplayString,
adTAeSCUSecAccountConnectionPort
Integer32,
adTAeSCUSecAccountDisconnectSession
Integer32
}
adTAeSCUSecAccountloginIndex OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index to indicate the order the user was logged in."
::= { adTAeSCUSecAccountLoggedInEntry 1 }
adTAeSCUSecAccountLoginUserIDIndex OBJECT-TYPE
SYNTAX Integer32 (1..16)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Security account user Index."
::= { adTAeSCUSecAccountLoggedInEntry 2 }
adTAeSCUSecAccountLoginUserID OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Security account user ID name."
::= { adTAeSCUSecAccountLoggedInEntry 3 }
adTAeSCUSecAccountConnectionType OBJECT-TYPE
SYNTAX INTEGER
{
craft(1),
adminPort(2),
ip(3),
x25(4),
rs485(5),
dcc(6),
fcd(7),
invalidConnection(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Method of connection to unit."
::= { adTAeSCUSecAccountLoggedInEntry 4 }
adTAeSCUSecAccountSessionType OBJECT-TYPE
SYNTAX INTEGER
{
menu(1),
tl1(2),
fcd(3),
ftp(4),
invalidSession(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Connection session type."
::= { adTAeSCUSecAccountLoggedInEntry 5 }
adTAeSCUSecAccountLoginConnectionSource OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..50))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Connection source of login. This could be an
IP address or some other type of address"
::= { adTAeSCUSecAccountLoggedInEntry 6 }
adTAeSCUSecAccountLoginDateTime OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..25))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"String display of login date and time.
Formant: mm/dd/yyyy and 24 hour time string
in format hh:mm:ss"
::= { adTAeSCUSecAccountLoggedInEntry 7 }
adTAeSCUSecAccountConnectionPort OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Port on which the indexed user's connection is established."
::= { adTAeSCUSecAccountLoggedInEntry 8 }
adTAeSCUSecAccountDisconnectSession OBJECT-TYPE
SYNTAX Integer32 (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Disconnect Indexed user's session."
::= { adTAeSCUSecAccountLoggedInEntry 9 }
--
-- Security Account Login Statistics
--
adTAeSCUSecLoginStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUSecLoginStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SCU Security Account table."
::= { adTAeSCUSecurityAccountMg 25 }
adTAeSCUSecLoginStatEntry OBJECT-TYPE
SYNTAX AdTAeSCUSecLoginStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SCU Security Login Statistics table."
INDEX { adTAeSCUSecAccountIndex}
::= { adTAeSCUSecLoginStatTable 1 }
AdTAeSCUSecLoginStatEntry ::=
SEQUENCE {
adTAeSCUSecLoginStatUserID
DisplayString,
adTAeSCUSecNumberOfLogins
Integer32,
adTAeSCUSecTotalNumLoginFailures
Integer32,
adTAeSCUSecNumFailuresSinceLastLogin
Integer32,
adTAeSCUSecLastLoginDateTime
DisplayString,
adTAeSCUSecLastConnectionType
INTEGER,
adTAeSCUSecLastSessionType
INTEGER,
adTAeSCUSecLastIPAddress
IpAddress
}
adTAeSCUSecLoginStatUserID OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Security account user ID name."
::= { adTAeSCUSecLoginStatEntry 3 }
adTAeSCUSecNumberOfLogins OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of logins recorded."
::= { adTAeSCUSecLoginStatEntry 5 }
adTAeSCUSecTotalNumLoginFailures OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of login failures recorded for the account."
::= { adTAeSCUSecLoginStatEntry 7 }
adTAeSCUSecNumFailuresSinceLastLogin OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of login failures since the last login of this account."
::= { adTAeSCUSecLoginStatEntry 9 }
adTAeSCUSecLastLoginDateTime OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..25))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"String display of login date and time.
Formant: mm/dd/yyyy and 24 hour time string
in format hh:mm"
::= { adTAeSCUSecLoginStatEntry 13 }
adTAeSCUSecLastConnectionType OBJECT-TYPE
SYNTAX INTEGER {
craftConnection(1),
adminConnection(2),
ntwkmgmtConnection(3),
ipConnection(4),
x25Connection(5),
rS485Connection(6),
dccConnection(7),
fCDConnection(8),
snmpConnection(9),
unknown1(10),
unknown2(11),
unknown3(12)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The connection type of the login."
::= { adTAeSCUSecLoginStatEntry 14 }
adTAeSCUSecLastSessionType OBJECT-TYPE
SYNTAX INTEGER {
menuSessionType(1),
tL1SessionType(2),
fcdSessionType(3),
ftpSessionType(4),
fsSessionType(5), -- Terminal Server
webSessionType(6),
cliSessionType(7),
unknown1(8),
unknown2(9),
unknown3(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Session Type of the login."
::= { adTAeSCUSecLoginStatEntry 15 }
adTAeSCUSecLastIPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The the IPAddress of the login."
::= { adTAeSCUSecLoginStatEntry 16 }
---
--- Advanced Login options
---
adTAeSCUSecAdvancedLoginOptions OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 26 }
adTAeSCUSecChallengeKey OBJECT-TYPE
SYNTAX INTEGER (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all security accounts expiration timer to value."
::= { adTAeSCUSecAdvancedLoginOptions 1 }
adTAeSCUSecMultiLoginAcct OBJECT-TYPE
SYNTAX INTEGER (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"READONLY accounts expiration timer."
::= { adTAeSCUSecAdvancedLoginOptions 2 }
adTAeSCUSecRemoteMenuAccessRequired OBJECT-TYPE
SYNTAX INTEGER (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set all READWRITEaccounts expiration timer settings value."
::= { adTAeSCUSecAdvancedLoginOptions 3 }
---
--- The following OIDs will only work with
---
---
--- Network Management Group
---
adTAeSCUNetworkMgmt OBJECT IDENTIFIER
::= { adTAeSCUmg 6 }
adTAeSCUNetworkMgmtPortBaudRate OBJECT-TYPE
SYNTAX INTEGER {
baud1200(1),
baud2400(2),
baud4800(3),
baud9600(4),
baud19200(5),
baud38400(6),
baud57600(7),
baud115200(8)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Network Interface Port Baud Rate."
::= { adTAeSCUNetworkMgmt 1 }
adTAeSCUNetworkMgmtPortComMode OBJECT-TYPE
SYNTAX INTEGER {
x25(1),
terminalServer(2),
pPP(3),
accessoryOption(4),
cLI(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Eth2/PPP0 Network interface port operating mode.."
::= { adTAeSCUNetworkMgmt 2 }
adTAeSCUNetworkMgmtPPPSerialPortMode OBJECT-TYPE
SYNTAX INTEGER {
async(1),
sync(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Determines wether the local eSCU PPP port will
use 'sync' or 'async' communications mode of the
network management port."
::= { adTAeSCUNetworkMgmt 3 }
adTAeSCUNetworkMgmtInterbankComMode OBJECT-TYPE
SYNTAX INTEGER {
host(1),
client(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Communication mode when systems are wired in a daisy chained configuration.
When installed as a standalone chassis it can be set to either value."
::= { adTAeSCUNetworkMgmt 4 }
adTAeSCUNetworkMgmtInterbankComModeWritable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Communication mode is not writable for CLIENT units when a HOST is present."
::= { adTAeSCUNetworkMgmt 5 }
adTAeSCUNetworkMgmtSecurityEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Require authentication."
::= { adTAeSCUNetworkMgmt 6 }
---
--- DNS related managment
---
adTAeSCUsDNS OBJECT IDENTIFIER
::= { adTAeSCUmg 7 }
adTAeScuDNSlookupService OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Determines whether DNS lookup services are
enabled."
::= { adTAeSCUsDNS 1 }
adTAeScuDNSprimaryIP OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Primary DNS name server IP address. Zero
signifies 'none'.
This OID is deprecated. Use ipDNSLookupIpNetAddress.1 to configure DNS Address."
::= { adTAeSCUsDNS 2 }
adTAeScuDNSsecondaryIP OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Secondary DNS name server IP address. Zero
signifies 'none'.
This OID is deprecated. Use ipDNSLookupIpNetAddress.2 to configure DNS Address."
::= { adTAeSCUsDNS 3 }
adTAeScuDNSsearchList OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..40))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Domain access search list. A space separated
list of domain names.
An empty string signifies 'none'."
::= { adTAeSCUsDNS 4 }
--
-- the DNS primary and secondary Address Translation table
--
ipDNSLookupIpTable OBJECT-TYPE
SYNTAX SEQUENCE OF IpDNSLookupIpTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The DNS primary and Secondary IP server..
Set primary DNS server index 1
Set secondary DNS server index 2"
::= { adTAeSCUsDNS 5 }
ipDNSLookupIpTableEntry OBJECT-TYPE
SYNTAX IpDNSLookupIpTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one IP address to `physical' address
equivalence."
INDEX { ipDNSLookupIpIndex}
::= { ipDNSLookupIpTable 1 }
IpDNSLookupIpTableEntry ::= SEQUENCE {
ipDNSLookupIpIndex Integer32,
ipDNSLookupIpInetAddressType InetAddressType,
ipDNSLookupIpInetAddress InetAddress
}
ipDNSLookupIpIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index value that uniquely identifies the primary or secondary
DNS server IP Address.
Index 1 for Primary DNS server address.
Index 2 for Secondary DNS server address."
::= { ipDNSLookupIpTableEntry 1 }
ipDNSLookupIpInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of ipDNSLookupIpNetAddress."
::= { ipDNSLookupIpTableEntry 2 }
ipDNSLookupIpInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The IP Address corresponding to the DNS server.
Index 1 for Primary DNS server address.
Index 2 for Secondary DNS server address.
Backwards compatibility: Setting this address to a IPv4
address will provision old primary or secondary DNS address.
Setting this address to an IPV6 will leave the old provision
address as is."
::= { ipDNSLookupIpTableEntry 3 }
---
--- Sofware/Config through TFTP
---
adTAeSCUFirmwareTFTPConfigMgmt OBJECT IDENTIFIER
::= { adTAeSCUmg 8 }
adTAeScuFirmwareTftpRemoteFileName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..40))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Firmware TFTP remote file name"
::= { adTAeSCUFirmwareTFTPConfigMgmt 1 }
adTAeScuFirmwareTftpServerHostName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..40))
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Symbolic DNS name or dotted-quad IP address of the
firmware TFTP server"
::= { adTAeSCUFirmwareTFTPConfigMgmt 2 }
adTAeScuFirmwareTftpServerIP OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Firmware TFTP server IP address. Zero
signifies 'none'.
This OID is deprecated. Use adTAeScmFirmwareTftpServerIPInetAddress
to configure Firmware TFTP server IP address. adTAeScmFirmwareTftpServerIPInetAddress
will accept Ipv4, IPv6, and domain name address"
::= { adTAeSCUFirmwareTFTPConfigMgmt 3 }
adTAeScuFirmwareTftpCacheExpire OBJECT-TYPE
SYNTAX Integer32 (0..1440)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The CacheExpire value specifies how many minutes a
flash file may be retained on the SCU before it will
again be retrieved from the TFTP server. If a subsequent
request for the same file is made within the CacheExpire
time, the local copy of the file will be reused, thus
reducing upgrade time and network traffic. A value of
zero indicates TFTP flash file caching should be disabled."
::= { adTAeSCUFirmwareTFTPConfigMgmt 4 }
adTAeScuFirmwareTftpInvalidate OBJECT-TYPE
SYNTAX INTEGER {
discardCurrentConfigInfo(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID instructs the TFTP Cache system to discard any
information that may be currently cached. The next TFTP
'get' operation will be being retrieved from the TFTP
host."
::= { adTAeSCUFirmwareTFTPConfigMgmt 5 }
adTAeScmFirmwareTftpServerInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Firmware TFTP server IP address type (Ipv6 or Ipv4)."
::= { adTAeSCUFirmwareTFTPConfigMgmt 6 }
adTAeScmFirmwareTftpServerIPInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Firmware TFTP server IP address. Ipv6 or Ipv4.
Backwards compatibility: Setting this address to a IPv4
address will update adTAeScuFirmwareTftpServerHostName address
with the new value.
Setting this address to an IPV6 will leave adTAeScuFirmwareTftpServerHostName as is."
::= { adTAeSCUFirmwareTFTPConfigMgmt 7 }
---
--- SCA () Sofware/Config related dids
---
adTAeSCUSystemConfigArchiveMgmt OBJECT IDENTIFIER
::= { adTAeSCUmg 9 }
adTAeScuSCATftpServerHostName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..40))
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Symbolic DNS name or dotted-quad IP address of the
config/SCA TFTP server.
This OID is deprecated. Use adTAeScuSCATftpServerHostNameInetAddress
to configure config/SCA TFTP server IP address."
::= { adTAeSCUSystemConfigArchiveMgmt 1 }
adTAeScuSCATftpServerIP OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Numeric IP address of the config/SCA TFTP server"
::= { adTAeSCUSystemConfigArchiveMgmt 2 }
adTAeScuSCATftpServerIPInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"InetAddressType of IP address of the config/SCA TFTP server"
::= { adTAeSCUSystemConfigArchiveMgmt 3 }
adTAeScuSCATftpServerHostNameInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP InetAddress of the config/SCA TFTP server.
Backwards compatibility: Setting this address to a IPv4
address will update adTAeScuSCATftpServerHostName provision address
with the new value.
Setting this address to an IPV6 will leave adTAeScuSCATftpServerHostName as is."
::= { adTAeSCUSystemConfigArchiveMgmt 4 }
---
--- SCA Auto Save Management
---
adTAeSCUSCAControl OBJECT IDENTIFIER
::= { adTAeSCUSystemConfigArchiveMgmt 10 }
adTAeScuSCAFileName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..40))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Config/SCA file name. SCA filename to use during
explicit or manual SCA save/restore operations from
SNMP and menu sessions. This filename has no affect
on SCA autosaves"
::= { adTAeSCUSCAControl 1 }
adTAeScuSCAInitiateSave OBJECT-TYPE
SYNTAX INTEGER {
initiate(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Initiate manual SCA Save operation to customer TFTP server."
::= { adTAeSCUSCAControl 2 }
adTAeScuSCAInitiateRestore OBJECT-TYPE
SYNTAX INTEGER {
initiate(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Initiate Restore of SCA from customer TFTP server"
::= { adTAeSCUSCAControl 3 }
adTAeScuSCAProvItemChanged OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bitmap of cards with changed provisions.
This read-only OID will return a bitmap of slots
whose provisions have changed since power-up or the
last SCA save operation. DB1 corresponds to slot 1,
DB31 corresponds to slot 31. DB0 corresponds to the
Accessory Slot."
::= { adTAeSCUSCAControl 4 }
adTAeScuSCAPresentCards OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bitmap of card 'present' in the shelf.
This read-only OID will return a bitmap of
slots with cards installed. DB1 corresponds
DB0 corresponds to the Accessory Slot."
::= { adTAeSCUSCAControl 5 }
adTAeScuSCASlotsWithProvData OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bitmap of slots with provision data.
This read-only OID will return a bitmap of slots
with provision information. DB1 corresponds to
slot 1, DB31 corresponds to slot 31. DB0 corresponds
to the Accessory Slot."
::= { adTAeSCUSCAControl 6 }
adTAeScuSCASlotsInSCA OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bitmap of slots in SCA.
This read-only OID will return a bitmap of slots
with provision information. DB1 corresponds to
slot 1, DB31 corresponds to slot 31. DB0 corresponds
to the Accessory Slot."
::= { adTAeSCUSCAControl 7 }
adTAeScuSCASlotsWithProvDataInSCA OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bitmap of slots with provision data in SCA.
This read-only OID will return a bitmap of slots
with provision information. DB1 corresponds to
slot 1, DB31 corresponds to slot 31. DB0 corresponds
to the Accessory Slot."
::= { adTAeSCUSCAControl 8 }
--- Status table
adTAeSCUSCAOperationStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUSCAOperationStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Operation status for each slot table."
::= { adTAeSCUSCAControl 10 }
adTAeSCUSCAOperationStatusEntry OBJECT-TYPE
SYNTAX AdTAeSCUSCAOperationStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Operation status for each slot table."
INDEX { adGenSlotInfoIndex}
::= { adTAeSCUSCAOperationStatusTable 1 }
AdTAeSCUSCAOperationStatusEntry ::=
SEQUENCE {
adTAeScuSCAOperationStatus
DisplayString
}
adTAeScuSCAOperationStatus OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SCA system status: This read-only string will return
a formatted string indicating the progress or status
of the current or most recent SCA operation."
::= { adTAeSCUSCAOperationStatusEntry 1 }
---
--- SCA Auto Save Management
---
adTAeSCUSCAAutoSaveMgmt OBJECT IDENTIFIER
::= { adTAeSCUSystemConfigArchiveMgmt 11 }
adTAeScuSCAAutoSave OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable AutoSave."
::= { adTAeSCUSCAAutoSaveMgmt 1 }
adTAeScuSCAAutoSaveRetries OBJECT-TYPE
SYNTAX Integer32 (1..99)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"AutoSave retries."
::= { adTAeSCUSCAAutoSaveMgmt 3 }
adTAeScuSCAAutoSaveIfChanged OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID allows the admin to reduce the amount of
SCA-related network traffic by instructing the eSCU
to save SCA information only if provision changes
have been made to the eSCU, MUX, or linecards."
::= { adTAeSCUSCAAutoSaveMgmt 5 }
adTAeScuSCAAutoSaveFileNamePrefix OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..30))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls the SCA autosave filename prefix,
which is used to construct the full SCA autosave
archive filename. The final filename will
consist of this prefix, a single underscore, a
single digit in the range 1..7 (instance) , and
the SCA filename suffix."
::= { adTAeSCUSCAAutoSaveMgmt 7 }
adTAeScuSCAAutoSaveFileNameSuffix OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..8))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls the SCA autosave filename suffix,
which is used to construct the full SCA autosave
archive filename. The final filename will consist
of the SCA filename prefix, a single underscore, a
single digit in the range 1..7 (instance), and this
SCA filename suffix."
::= { adTAeSCUSCAAutoSaveMgmt 9 }
adTAeScuSCAAutoSaveInstances OBJECT-TYPE
SYNTAX Integer32 (1..7)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls the maximum number of SCA filename
instances to save, or 'rotate' through on the SCA
TFTP server. The eSCU will first save instance '1',
then '2', up to the value specified by this OID,
then cycle back to '1' on the subsequent save."
::= { adTAeSCUSCAAutoSaveMgmt 11 }
adTAeScuSCAAutoSaveHoursAfter OBJECT-TYPE
SYNTAX Integer32 (0..23)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls how many hours after midnight autosave
operations should be scheduled. This allows the admin to
balance the SCA autosave load of many shelves so that all
the systems will not be attempting to contact the SCA
TFTP server at the same time."
::= { adTAeSCUSCAAutoSaveMgmt 13 }
adTAeScuSCAAutoSaveMinutesAfter OBJECT-TYPE
SYNTAX Integer32 (0..59)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls how many minutes after the 'hour' oid
autosave operations should be scheduled. This allows
the admin to balance the SCA autosave load of many
shelves so that all the systems will not be attempting
to contact the SCA TFTP server at the same time."
::= { adTAeSCUSCAAutoSaveMgmt 15 }
adTAeScuSCADateTimeLastAutoSave OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This read-only OID will return the ASCII date/time of
the last SCA autosave operation, or
an empty string if none."
::= { adTAeSCUSCAAutoSaveMgmt 17 }
adTAeScuSCADateTimeNextAutoSave OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This read-only OID will return the ASCII date/time of
the next SCA autosave operation, or
an empty string if none."
::= { adTAeSCUSCAAutoSaveMgmt 18 }
---
--- SCA Restore Management
---
adTAeSCUSCARestoreMgmt OBJECT IDENTIFIER
::= { adTAeSCUSystemConfigArchiveMgmt 12 }
adTAeScuSCAoptRestoreESCU OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether any eSCU-related
provisions should be restored and is a master
override for the restore of all eSCU-related
provisions. Setting this OID to 'disable'
will result in all of the following eSCU-related
enable/disable settings being evaluated
as 'disabled' at the time of an SCA restore
operation. Setting this value to 'enable' will
result in the normal evaluation of each following
eSCU-related enable/disable settings."
::= { adTAeSCUSCARestoreMgmt 1 }
adTAeScuSCAoptRestoreSCA OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether SCA-related
provisions should be restored on the eSCU."
::= { adTAeSCUSCARestoreMgmt 2 }
adTAeScuSCAoptRestoreNetwork OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether general IP
network-related provisions should be restored
on the eSCU. This would include such items as
secondary telnet port numbers, IP-forwarding enable,
etc."
::= { adTAeSCUSCARestoreMgmt 3 }
adTAeScuSCAoptRestoreNetworkInterface OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether IP network interface-related provisions should
be restored on the eSCU. This would include such items as
IP/netmask/gateway/default-route settings on the IP network interfaces."
::= { adTAeSCUSCARestoreMgmt 4 }
adTAeScuSCAoptRestoreSNMP OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether SNMP-related
provisions should be restored on the eSCU."
::= { adTAeSCUSCARestoreMgmt 5 }
adTAeScuSCAoptRestoreSecurity OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether security-system
provisions should be restored on the eSCU.
This would include such items as user
account information."
::= { adTAeSCUSCARestoreMgmt 6 }
adTAeScuSCAoptRestoreLineCard OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether provisions should
be restored to linecards and MUXs and is a master
override for the restore of all Module-related
provisions. Setting this OID to 'disable'
will result in all of the following Module-related
enable/disable settings being evaluated
as 'disabled' at the time of an SCA restore
operation. Setting this value to 'enable' will
result in the normal evaluation of each following
Module-related enable/disable settings."
::= { adTAeSCUSCARestoreMgmt 7 }
adTAeScuSCAoptRestoreInServiceLineCard OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether provisions should
be restored to in-service linecards and MUXs."
::= { adTAeSCUSCARestoreMgmt 8 }
adTAeScuSCAoptRestoreEmptySlot OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This OID controls whether provisions should
be restored to empty slots. This operation is often
called pre-provisioning."
::= { adTAeSCUSCARestoreMgmt 9 }
adTAeScuSCAoptRestoreCardBitmask OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"SCA restore to linecard enable bitmask.
This OID accesses a enable/disable bitmap indicating which slots
should have their provision information restored during an SCA
restore operation. Valid slots are 1..30 or 1..24, depending on
shelf type. DB1 corresponds to slot 1, DB31 corresponds to slot
31."
::= { adTAeSCUSCARestoreMgmt 12 }
adTAeScuSCADateTimeSaveInvoked OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This read-only OID will return the ASCII date/time of the
last manually-invoked SCA save operation, or an empty
string if none."
::= { adTAeSCUSCARestoreMgmt 13 }
adTAeScuSCACardsRestoredBitmask OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This read-only OID will return a bitmask of cards restored."
::= { adTAeSCUSCARestoreMgmt 14 }
adTAeScuSCACardsNotRestoredBitmask OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This read-only OID will return a bitmask of cards not restored."
::= { adTAeSCUSCARestoreMgmt 15 }
adTAeScuSCACardsExcludedBitmask OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This read-only OID will return a bitmask of cards excluding from
the SCA restore operation."
::= { adTAeSCUSCARestoreMgmt 16 }
adTAeScuSCARestoreCardErrorsBitmask OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This read-only OID will return a bitmask of cards with restore errors."
::= { adTAeSCUSCARestoreMgmt 17 }
--
--
--
--
--
--
--
--
--
--
-- System Log group
--
--
--
adTAeSCUSystemLog OBJECT IDENTIFIER
::= { adTAeSCUmg 14 }
adTAeSCUSystemLogAlarm OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable System full alaram."
::= { adTAeSCUSystemLog 3 }
adTAeSCUSystemLogPercentFull OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Percentage of System Log buffer used. When the
System Log is full it will remove the oldest half
of its entries. When the System log is 70% full,
it will send a alarm every 5% used so an administration
could upload the system log."
::= { adTAeSCUSystemLog 5 }
adTAeSCUSystemLogCount OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of entries in system log."
::= { adTAeSCUSystemLog 7 }
adTAeSCUSystemSummReport OBJECT-TYPE
SYNTAX INTEGER {
allEvents(1),
loginAndLogoutEvents(2), -- all login and logouts
accountChangesEvents(3), -- all changes made to accounts
snmpProvisioning(4), -- all provisions but not account changes
networkProvisioning(5), -- all provisions but not account changes
tftpYmodemUpdates(6), -- all TFTP Ymodem firmware Updates
scaEvents(7), -- SCA provisioning and events
securityOptionsProv(8), -- Security options provisioned
dateAndTimeProv(9) -- date and time changes
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allows summary reports.."
::= { adTAeSCUSystemLog 8 }
adTAeSCUSystemEnableDetail OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable detail reports."
::= { adTAeSCUSystemLog 9 }
adTAeSCUSystemLogFailureDescription OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An string description of a system log Failure.
This OID is valid in a SNMP trap."
::= { adTAeSCUSystemLog 10 }
adTAeSCUSystemLogTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeSCUSystemLogEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SCU System Log table."
::= { adTAeSCUSystemLog 15 }
adTAeSCUSystemLogEntry OBJECT-TYPE
SYNTAX AdTAeSCUSystemLogEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SCU System Log table.
Readonly object."
INDEX { adTAeSCUSystemLogIndex }
::= { adTAeSCUSystemLogTable 1 }
AdTAeSCUSystemLogEntry ::=
SEQUENCE {
adTAeSCUSystemLogIndex
Integer32,
adTAeSCUSystemLogDescription
DisplayString
}
adTAeSCUSystemLogIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An not-accessible index value. The contoller will not respond to this OID."
::= { adTAeSCUSystemLogEntry 1 }
adTAeSCUSystemLogDescription OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An string description of a system log entry."
::= { adTAeSCUSystemLogEntry 5 }
--
--
--
--
-- adTAeScuTL1ActivityLog group
--
--
--
adTAeScuTL1ActivityLog OBJECT IDENTIFIER
::= { adTAeSCUmg 15 }
adTAeScuResetTL1Log OBJECT-TYPE
SYNTAX INTEGER {
resetTL1Log(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Reset TL1 Log. "
::= { adTAeScuTL1ActivityLog 2 }
adTAeScuTL1ActivityLogTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeScuTL1ActivityLogEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The System TL1 Log table."
::= { adTAeScuTL1ActivityLog 6 }
adTAeScuTL1ActivityLogEntry OBJECT-TYPE
SYNTAX AdTAeScuTL1ActivityLogEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the System TL1 Log table.
Readonly object."
INDEX { adTAeSCUTL1LogIndex}
::= { adTAeScuTL1ActivityLogTable 1 }
AdTAeScuTL1ActivityLogEntry ::=
SEQUENCE {
adTAeSCUTL1LogIndex
Integer32,
adTAeScuTL1ActivityLogDescription
DisplayString
}
adTAeSCUTL1LogIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An Index value to the TL1 Log.."
::= { adTAeScuTL1ActivityLogEntry 1 }
adTAeScuTL1ActivityLogDescription OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An string description of a system Tl1 log entry.
This string contains the TL1 command and response."
::= { adTAeScuTL1ActivityLogEntry 2 }
--
--
--
--
-- Password Complexity Config
--
--
adTAeSCUSysPasswordComplexity OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 10 }
adTAeSCUSysEnablePswdComplexity OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable Password Complexity algorithms."
::= { adTAeSCUSysPasswordComplexity 1 }
adTAeSCUSysMinPasswordLength OBJECT-TYPE
SYNTAX Integer32 (6..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Minimum password length required."
::= { adTAeSCUSysPasswordComplexity 2 }
adTAeSCUSysUpperCaseRequired OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Upper case character required in password."
::= { adTAeSCUSysPasswordComplexity 3 }
adTAeSCUSysLowerCaseRequired OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Lower case character required in password."
::= { adTAeSCUSysPasswordComplexity 4 }
adTAeSCUSysDigitRequired OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A digit is required in password."
::= { adTAeSCUSysPasswordComplexity 5 }
adTAeSCUSysSpecialCharacterRequired OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A special character is required in password."
::= { adTAeSCUSysPasswordComplexity 6 }
adTAeSCUSysCaseSensitivePassword OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The system will store a case sensitive password."
::= { adTAeSCUSysPasswordComplexity 7 }
adTAeSCUSysNullPasswordAccepted OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This OID will no longer work. A NULL password is accepted."
::= { adTAeSCUSysPasswordComplexity 8 }
adTAeSCUSecPasswordStartEndDigitCheck OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Password cannot start or end with a digit."
::= { adTAeSCUSysPasswordComplexity 10 }
adTAeSCUSecLastSixPasswordCheck OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Password cannot be the same as previous six passwords."
::= { adTAeSCUSysPasswordComplexity 12 }
--
--
--
--
-- RADIUS Login Config
--
--
adTAeSCUSysRADIUsConfig OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 9 }
adTAeScuRADIUSServAuthentication OBJECT-TYPE
SYNTAX INTEGER {
enableRADIUSAuthentication(1), -- Use RADIUS server to login
enableLocalAccountAuthentication(2) -- Use the local accounts.
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Determine how the user Login into the system. "
::= { adTAeSCUSysRADIUsConfig 2 }
adTAeScuRadiusTL1Authentication OBJECT-TYPE
SYNTAX INTEGER {
enableRADIUSAuthentication(1), -- Use RADIUS server to login
enableLocalAccountAuthentication(2) -- Use the local accounts.
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Determine how the user Login into TL1. "
::= { adTAeSCUSysRADIUsConfig 3 }
adTAeScuRadiusAccountAccessLevel OBJECT-TYPE
SYNTAX INTEGER {
noneRejectLogin(1), -- No access. Reject login
readOnlyAccess(2), -- READ_ONLY Access.
readWriteAccess(3), -- READ_WRITE Access
testAccess(4), -- TEST access
configAccess(5), -- CONFIG access
adminAccess(6) -- ADMIN access
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Default account access previledge given to a RADIUS account
if the RADIUS Server does not provide the Adtran level.
Access privilege will be communicated as a Vendor Specific
Attribute in the RADIUS Server reply packet.
# Values for Adtran-Telnet-Level attribute for the Total Access IADs
# This attribute sets the Access level granted to a user for a particular
# telnet session.
VALUE Adtran-IAD-Telnet-Level Level-Full 0
VALUE Adtran-IAD-Telnet-Level Level-Support 1
VALUE Adtran-IAD-Telnet-Level Level-Config 2
VALUE Adtran-IAD-Telnet-Level Level-Router 3
VALUE Adtran-IAD-Telnet-Level Level-Voice 4
VALUE Adtran-IAD-Telnet-Level Level-Status 5
*********where*************
-- ADMIN - Level-Full
-- CONFIG - Level-Config
-- TEST - Level-Support
-- READ_WRITE - Level-Router
-- READ_ONLY - Level-Status.
"
::= { adTAeSCUSysRADIUsConfig 4 }
adTAeScuRADIUSFallbackMode OBJECT-TYPE
SYNTAX INTEGER {
retryRADIUSAuthentication(1), -- Use RADIUS server to login
fallbackToLocalAccountAuthentication(2) -- Use the local accounts.
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Determine how the user Login to the controller there is a failure to
contact all four RADIUS servers.
If fall back mode will be controlled by adTAeSCUSecAccountAuthenticationMethod.
If adTAeSCUSecAccountAuthenticationMethod works then this OID is ignored."
::= { adTAeSCUSysRADIUsConfig 5 }
adTAeScuRADIUSServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeScuRADIUSServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"RADIUS authentication settings."
::= { adTAeSCUSysRADIUsConfig 6 }
--
--
adTAeScuRADIUSServerEntry OBJECT-TYPE
SYNTAX AdTAeScuRADIUSServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the RADIUS settings table."
INDEX { adTAeScuRadiusCfgIndex}
::= { adTAeScuRADIUSServerTable 1 }
AdTAeScuRADIUSServerEntry ::=
SEQUENCE {
adTAeScuRadiusCfgIndex
Integer32,
adTAeScuRadiusServerAddress
DisplayString,
adTAeScuRadiusServerPortNumber
Integer32,
adTAeScuRadiusServerSecret
DisplayString,
adTAeScuRADIUSServRetries
Integer32,
adTAeScuRADIUSServContactTimeOut
Integer32,
adTAeScuRadiusServerSequence
Integer32,
adTAeScuRadiusServerName
DisplayString,
adTAeScuRadiusServerAddressType
InetAddressType,
adTAeScuRadiusServerInetAddress
InetAddress
}
adTAeScuRadiusCfgIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An Index to RADIUS authentication settings"
::= { adTAeScuRADIUSServerEntry 1 }
adTAeScuRadiusServerAddress OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"RADIUS Server IP address.
deprecated to support IPv6. Use adTAeScuRadiusServerInetAddress."
::= { adTAeScuRADIUSServerEntry 2 }
adTAeScuRadiusServerPortNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"RADIUS Server IP port address."
::= { adTAeScuRADIUSServerEntry 3 }
adTAeScuRadiusServerSecret OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The key used in encrypting the packets passed between the
RADIUS Server and the client. This key must match the one
configured on the server."
::= { adTAeScuRADIUSServerEntry 4 }
adTAeScuRADIUSServRetries OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Number of retries to contact RADIUS Server. "
::= { adTAeScuRADIUSServerEntry 5 }
adTAeScuRADIUSServContactTimeOut OBJECT-TYPE
SYNTAX Integer32 (1000..30000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"RADIUS Server responses time out in milliseconds."
::= { adTAeScuRADIUSServerEntry 6 }
adTAeScuRadiusServerSequence OBJECT-TYPE
SYNTAX Integer32 (0..4)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"RADIUS Server sequence that ranks priority of each server.
[0] if no IP is assigned at given index.
[1-4] for each additional server added in increasing order. The default
sequence will match the index that each server is found at."
::= { adTAeScuRADIUSServerEntry 7 }
adTAeScuRadiusServerName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Name to be assigned to a given RADIUS server for ease of reference.
Can use either the given name assigned or the IP associated with
server to reference it."
::= { adTAeScuRADIUSServerEntry 8 }
adTAeScuRadiusServerAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of adTAeScuRadiusServerInetAddress."
::= { adTAeScuRADIUSServerEntry 9 }
adTAeScuRadiusServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"RADIUS Server IP address.
Backwards compatibility: Setting this address to a IPv4
address will provision old address adTAeScuRadiusServerAddress
with the new address.
Setting this address to an IPV6 will leave the old provision
address adTAeScuRadiusServerAddress as is."
::= { adTAeScuRADIUSServerEntry 10 }
--
-- Account Lock-out Settings
--
adTAeScuAccLockOutSettings OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 12 }
adTAeScuEnableAccLoginFailureLockOut OBJECT-TYPE
SYNTAX Integer32 (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable users to be locked-out after failed login attempts."
::= { adTAeScuAccLockOutSettings 1 }
adTAeScuEnableLockOutAlarm OBJECT-TYPE
SYNTAX Integer32 (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Generate an alarm when an account triggers lock-out conditions."
::= { adTAeScuAccLockOutSettings 2 }
adTAeScuEnableIndefLockOut OBJECT-TYPE
SYNTAX Integer32 (1..2)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Forces the account to be reset by an Administrator once locked.."
::= { adTAeScuAccLockOutSettings 3 }
adTAeScuNumLockOutLoginAttempts OBJECT-TYPE
SYNTAX Integer32 (2..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Number of consecutive failed login attempts before a lockout occurs."
::= { adTAeScuAccLockOutSettings 4 }
adTAeScuLockOutDuration OBJECT-TYPE
SYNTAX Integer32 (1..60)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of minutes the user will be locked out."
::= { adTAeScuAccLockOutSettings 5 }
--
--
adTAeTrustedClientConfig OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 13 }
adTAeTrustedIPClientAccessControl OBJECT-TYPE
SYNTAX INTEGER {
enableTrustedClientAccessControl(1), -- enable Trusted Client Access Control
disableTrustedClientAccessControl(2) -- disable Trusted Client Access Control.
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable IP Access to the controller based on the Trusted IP Client list.
An IP address not on the list will be rejected.
**********WARNING**********
If there are no adTAeTrustedIPClientEntry, a SNMP wrong value error will be returned.
***************************
"
::= { adTAeTrustedClientConfig 3 }
adTAeTrustedIPClientAccessName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..49))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Tursted IP Access-list name.
Deletes all Trusted IP Clients when set to an empty string.
Disables Trusted IP Clients feature when set to an empty string."
::= { adTAeTrustedClientConfig 4 }
adTAeTrustedIPClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeTrustedIPClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Trusted IP Client Table."
::= { adTAeTrustedClientConfig 6 }
adTAeTrustedInetClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeTrustedInetClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"IPv4 and IPv6 Trusted IP Client Table."
::= { adTAeTrustedClientConfig 8 }
adTAeTrustedIPClientEntry OBJECT-TYPE
SYNTAX AdTAeTrustedIPClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in theTrusted IP Client table."
INDEX { adTAeTrustedIPAddress,adTAeTrustedIPNetworkBits}
::= { adTAeTrustedIPClientTable 1 }
AdTAeTrustedIPClientEntry ::=
SEQUENCE {
adTAeTrustedIPAddress
IpAddress,
adTAeTrustedIPNetworkBits
Integer32,
adTAeTrustedClientStatus
INTEGER,
adTAeTrustedClientResource
INTEGER
}
adTAeTrustedClientStatus OBJECT-TYPE
SYNTAX INTEGER {
active(1), -- Trusted IP Client is active
createTrustedClient(2), -- Create a Trusted IP Client
deleteTrustedClient(3) -- Delete a Trusted IP Client
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"An Index to adTAeTrustedIPClientTable."
::= { adTAeTrustedIPClientEntry 1 }
adTAeTrustedIPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An IPv4 address that is allowed access to the controller. "
::= { adTAeTrustedIPClientEntry 2 }
adTAeTrustedIPNetworkBits OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This number is used to generate a netmask. Each connection
IP address is masked and compeared to a adTAeTrustedIPAddress
masked generated by adTAeTrustedIPNetworkBits to see if the
connection request is a Trusted IP Address.
NetMasks generated by adTAeTrustedIPNetworkBits:
1 0x80000000 9 0xFF800000 17 0xFFFF8000 25 0xFFFFFF80
2 0xC0000000 10 0xFFC00000 18 0xFFFFC000 26 0xFFFFFFC0
3 0xE0000000 11 0xFFE00000 19 0xFFFFE000 27 0xFFFFFFE0
4 0xF0000000 12 0xFFF00000 20 0xFFFFF000 28 0xFFFFFFF0
5 0xF8000000 13 0xFFF80000 21 0xFFFFF800 29 0xFFFFFFF8
6 0xFC000000 14 0xFFFC0000 22 0xFFFFFC00 30 0xFFFFFFFC
7 0xFE000000 15 0xFFFE0000 23 0xFFFFFE00 31 0xFFFFFFFE
8 0xFF000000 16 0xFFFF0000 24 0xFFFFFF00 32 0xFFFFFFFF
"
::= { adTAeTrustedIPClientEntry 3 }
adTAeTrustedClientResource OBJECT-TYPE
SYNTAX INTEGER {
allPorts(1), -- Trusted IP Client Unlimited Access
snmpPorts(2), -- Trusted IP Client SNMP Access
menuPorts(3), -- Trusted IP Client Menu Access
tL1Ports(4), -- Trusted IP Client TL1 Access
snmpMenuPorts(5), -- Trusted IP Client SNMP and Menu Access
snmpTL1Ports(6), -- Trusted IP Client SNMP and TL1 Access
menuTL1Ports(7) -- Trusted IP Client Menu and TL1 Access
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicate what type of access a trusted client has."
::= { adTAeTrustedIPClientEntry 4 }
adTAeTrustedInetClientEntry OBJECT-TYPE
SYNTAX AdTAeTrustedInetClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the IPv4 and IPv6 Trusted IP Client Table."
INDEX {adTAeTrustedInetAddressType,adTAeTrustedInetNetworkBits,adTAeTrustedInetAddress}
::= { adTAeTrustedInetClientTable 1 }
AdTAeTrustedInetClientEntry ::=
SEQUENCE {
adTAeTrustedInetClientStatus
INTEGER,
adTAeTrustedInetAddressType
InetAddressType,
adTAeTrustedInetNetworkBits
Integer32,
adTAeTrustedInetAddress
InetAddress,
adTAeTrustedInetClientResource
INTEGER
}
adTAeTrustedInetClientStatus OBJECT-TYPE
SYNTAX INTEGER {
active(1), -- Trusted IP Client is active
createTrustedClient(2), -- Create a Trusted IP Client
deleteTrustedClient(3) -- Delete a Trusted IP Client
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The status of the IPv4 and IPv6 address in the Trusted IP Client Table."
::= { adTAeTrustedInetClientEntry 1 }
adTAeTrustedInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of adTAeTrustedInetAddress."
::= { adTAeTrustedInetClientEntry 2 }
adTAeTrustedInetNetworkBits OBJECT-TYPE
SYNTAX Integer32 (1..128)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This number is used to generate a netmask. Each connection
IP address is masked and compared to a adTAeTrustedInetAddress
masked generated by adTAeTrustedInetNetworkBits to see if the
connection request is a Trusted IP Address.
"
::= { adTAeTrustedInetClientEntry 3 }
adTAeTrustedInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An IPv4 or IPv6 address that is allowed access to the controller. "
::= { adTAeTrustedInetClientEntry 4 }
adTAeTrustedInetClientResource OBJECT-TYPE
SYNTAX INTEGER {
allPorts(1), -- Trusted IP Client Unlimited Access
snmpPorts(2), -- Trusted IP Client SNMP Access
tL1Ports(3), -- Trusted IP Client TL1 Access
snmpTL1Ports(4) -- Trusted IP Client SNMP and TL1 Access
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicate what type of access a trusted client has in the
IPv4 and IPv6 Trusted IP Client Table.."
::= { adTAeTrustedInetClientEntry 5 }
--
--
--
--
-- Advisory Warning Configuration
--
--
adTAeSCUSysAdvisoryConfig OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 20 }
--
--
adTAeScuEnableMenuAdvisoryWarningMsg OBJECT-TYPE
SYNTAX INTEGER {
enableAdvisoryWarningMsg(1), -- Enable AdvisoryWarning
disableAdvisoryWarniningMsg(2) -- Disable Advisory Warning
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable Menu Advisory Waring Message."
::= { adTAeSCUSysAdvisoryConfig 1 }
adTAeScuEnableTL1AdvisoryWarningMsg OBJECT-TYPE
SYNTAX INTEGER {
enableAdvisoryWarningMsg(1), -- Enable AdvisoryWarning
disableAdvisoryWarningMsg(2) -- Disable Advisory Warning
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable TL1 Advisory Warning Message."
::= { adTAeSCUSysAdvisoryConfig 2 }
adTAeScuSysSavedTextJustification OBJECT-TYPE
SYNTAX INTEGER {
leftJustification(1), -- Left Text Justification
rightJustification(2), -- Center Text Justification
centerJustification(3) -- Right Text Justification
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Set the text justification for how the Advisory Warning is displayed."
::= { adTAeSCUSysAdvisoryConfig 3 }
adTAeScuSavedAdvisoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeScuSavedAdvisoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Non-Volatile Saved Advisory Warning."
::= { adTAeSCUSysAdvisoryConfig 6 }
adTAeScuSavedAdvisoryEntry OBJECT-TYPE
SYNTAX AdTAeScuSavedAdvisoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the adTAeScuSavedAdvisoryTable."
INDEX { adTAeScuAdvisoryLineIndex}
::= { adTAeScuSavedAdvisoryTable 1 }
AdTAeScuSavedAdvisoryEntry ::=
SEQUENCE {
adTAeScuAdvisoryLineIndex
Integer32,
adTAeScuSavedAdvisoryWarning
DisplayString
}
adTAeScuAdvisoryLineIndex OBJECT-TYPE
SYNTAX Integer32 (1..20)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An Index to Advisory Warning line."
::= { adTAeScuSavedAdvisoryEntry 1 }
adTAeScuSavedAdvisoryWarning OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Advisory Warning line."
::= { adTAeScuSavedAdvisoryEntry 2 }
--
--
adTAeScuSysSaveOrResetEditAdvisoryWarning OBJECT-TYPE
SYNTAX INTEGER {
saveAdvisoryWarningChanges(1), -- Save Edited Advisory Warning
resetAdvisoryWarning(2), -- Replace Edited Advisory Warning with Saved advisory warning.
defaultGetValue(999) -- Dummy default value returned
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Save edit changes made to Advisory Warning.
saveAdvisoryWarningChanges - Save the Edited Advisory Warning
resetAdvisoryWarning - Reset Edited Advisory Warning with saved one
defaultGetValue - dummy value returned on a get value"
::= { adTAeSCUSysAdvisoryConfig 10 }
adTAeScuSysEditTextJustification OBJECT-TYPE
SYNTAX INTEGER {
leftJustification(1), -- Left Text Justification
rightJustification(2), -- Center Text Justification
centerJustification(3) -- Right Text Justification
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Set the text justification for how the Advisory Warning is displayed."
::= { adTAeSCUSysAdvisoryConfig 11 }
adTAeScuEditedAdvisoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeScuEditedAdvisoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Volatile Edited Advisory Warning."
::= { adTAeSCUSysAdvisoryConfig 15 }
adTAeScuEditedAdvisoryEntry OBJECT-TYPE
SYNTAX AdTAeScuEditedAdvisoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Volatile Edited Advisory Warning line."
INDEX { adTAeScuAdvisoryLineIndex}
::= { adTAeScuEditedAdvisoryTable 1 }
AdTAeScuEditedAdvisoryEntry ::=
SEQUENCE {
adTAeScuEditedAdvisoryWarning
DisplayString
}
adTAeScuEditedAdvisoryWarning OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Volatile Ram Edited Advisory Warning line."
::= { adTAeScuEditedAdvisoryEntry 2 }
--
--
--
--
-- Bulk Data Export server Config
--
--
adTAeSCUSysBulkDataExportServerConfig OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 21 }
adTAeSCUSysBulkDataExportHost OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The IP address of the server to receive exported bulk data files."
::= { adTAeSCUSysBulkDataExportServerConfig 1 }
adTAeSCUSysBulkDataExportUserName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The user name for the server to receive exported bulk data files,
Maximum number of 30 characters for the username."
::= { adTAeSCUSysBulkDataExportServerConfig 2 }
adTAeSCUSysBulkDataExportPassword OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The password of the server to receive exported bulk data files.
Maximum number of 30 characters for the password."
::= { adTAeSCUSysBulkDataExportServerConfig 3 }
adTAeSCUSysBulkDataExportProtocol OBJECT-TYPE
SYNTAX INTEGER {
none(0),
tftp(1),
ftp(3),
sftp(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The protocol used to transfer the exported bulk data files."
::= { adTAeSCUSysBulkDataExportServerConfig 4 }
adTAeSCUSysBulkDataExportPort OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The port used to transfer the exported bulk data files."
::= { adTAeSCUSysBulkDataExportServerConfig 5 }
adTAeSCUSysBulkDataExportPath OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The destination path on the server to export bulk data files.
Maximum number of 200 characters for the path."
::= { adTAeSCUSysBulkDataExportServerConfig 6 }
--
--
--
-- System Log Alarms
--
--
adTAeSCUmgNotificationEvents OBJECT-IDENTITY
STATUS current
DESCRIPTION "The SCU/SCM controller events"
::= { adTAeSCU 0 }
adTAeSCUSystemLogFull NOTIFICATION-TYPE
OBJECTS {
adTrapInformSeqNum,
sysName,
adTAeSCUSystemLogPercentFull
}
STATUS current
DESCRIPTION
"System Log is 90% full. The System Log has a circular buffer.
The System Log will destroy the oldest half of its entries when
it is 100% full. This alarm is used to notify Management
stations to download the System Log so entries may not be lost."
--#TYPE "Warning - System Log is full."
--#SUMMARY "TAeSCU 24101: System Log is %d percent full;"
--#SUMMARY "detected at chassis: %s"
--#ARGUMENTS { 2, 1}
--#SEVERITY INFORMATIONAL
--#GENERIC 6
--#CATEGORY "System Log Events"
--#SOURCE_ID "A"
--#TIMEINDEX 0
::= { adTAeSCUmgNotificationEvents 24101}
adTAeSCUSystemLogInvalidAuthentAtt NOTIFICATION-TYPE
OBJECTS {
adTrapInformSeqNum,
sysName
}
STATUS current
DESCRIPTION
"Invalid user authentication attempts."
--#TYPE "Warning - Invalid authentication attempts surpassed."
--#SUMMARY "TAeSCU 24103: Invalid authentication attempts surpassed."
--#SUMMARY "detected at chassis: %s"
--#ARGUMENTS { 1}
--#SEVERITY INFORMATIONAL
--#GENERIC 6
--#CATEGORY "System Log Events"
--#SOURCE_ID "A"
--#TIMEINDEX 0
::= { adTAeSCUmgNotificationEvents 24103 }
adTAeSCUSystemLogFailure NOTIFICATION-TYPE
OBJECTS {
adTrapInformSeqNum,
sysName,
adTAeSCUSystemLogPercentFull,
adTAeSCUSystemLogCount,
adTAeSCUSystemLogFailureDescription
}
STATUS current
DESCRIPTION
"System Log fails to record an event."
--#TYPE "Warning - System Log fails to record an event."
--#SUMMARY "TAeSCU 24105: System Log fails to record an event.;"
--#SUMMARY "detected at chassis: %s"
--#ARGUMENTS { 1}
--#SEVERITY INFORMATIONAL
--#GENERIC 6
--#CATEGORY "System Log Events"
--#SOURCE_ID "A"
--#TIMEINDEX 0
::= { adTAeSCUmgNotificationEvents 24105 }
adTAeSCUSystemInactiveAccountExpiration NOTIFICATION-TYPE
OBJECTS {
adTrapInformSeqNum,
sysName,
adTAeSCUSecAccountUserID,
adTAeSCUSecAccountAge
}
STATUS current
DESCRIPTION
"Inactive account expiration notification. Account set to expired."
--#TYPE "Warning - Account set to expired."
--#SUMMARY "TAeSCU 24163: Account %s Expired.;"
--#SUMMARY "detected at chassis: %s"
--#ARGUMENTS { 2,1}
--#SEVERITY INFORMATIONAL
--#GENERIC 6
--#CATEGORY "System Log Events"
--#SOURCE_ID "A"
--#TIMEINDEX 0
::= { adTAeSCUmgNotificationEvents 24163 }
--
--
--
-- Start of TACACSPlus Login Config
--
--
adTAeSCUSysTACACSPlusConfig OBJECT IDENTIFIER
::= { adTAeSCUSecurityAccountMg 30 } -- number from the air
adTAeScuTACACSPlusTL1Authentication OBJECT-TYPE
SYNTAX INTEGER {
enableTACACSAuthentication(1), -- Use TACACS Plus server to login
disableTACACSAuthentication(2) -- Use other methods to login.
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Determine how the user Login into TL1. "
::= { adTAeSCUSysTACACSPlusConfig 3 }
adTAeScuTACACSPlusServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF AdTAeScuTACACSPlusServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"TACACS Plus authentication settings."
::= { adTAeSCUSysTACACSPlusConfig 6 }
--
--
adTAeScuTACACSPlusServerEntry OBJECT-TYPE
SYNTAX AdTAeScuTACACSPlusServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the TACACS Plus settings table."
INDEX { adTAeScuTACACSPlusCfgIndex}
::= { adTAeScuTACACSPlusServerTable 1 }
AdTAeScuTACACSPlusServerEntry ::=
SEQUENCE {
adTAeScuTACACSPlusCfgIndex
Integer32,
adTAeScuTACACSPlusServerAddress
DisplayString,
adTAeScuTACACSPlusServerName
DisplayString,
adTAeScuTACACSPlusServerSecret
DisplayString,
adTAeScuTACACSPlusServerSequence
Integer32,
adTAeScuTACACSPlusServContactTimeOut
Integer32,
adTAeScuTACACSPlusServerPort
Integer32,
adTAeScuTACACSPlusServerAddressType
InetAddressType,
adTAeScuTACACSPlusServerInetAddress
InetAddress
}
adTAeScuTACACSPlusCfgIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An Index to TACACS Plus authentication settings"
::= { adTAeScuTACACSPlusServerEntry 1 }
adTAeScuTACACSPlusServerAddress OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"TACACS Plus Server IP address.
deprecated to support IPv6. Use adTAeScuTACACSPlusServerInetAddress.
"
::= { adTAeScuTACACSPlusServerEntry 2 }
adTAeScuTACACSPlusServerName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"TACACS Plus Server Name."
::= { adTAeScuTACACSPlusServerEntry 3 }
adTAeScuTACACSPlusServerSecret OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The key used in encrypting the packets passed between the
TACACS Plus Server and the client. This key must match the one
configured on the server."
::= { adTAeScuTACACSPlusServerEntry 4 }
adTAeScuTACACSPlusServerSequence OBJECT-TYPE
SYNTAX Integer32 (0..4)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"TACACS Plus Server sequence."
::= { adTAeScuTACACSPlusServerEntry 5 }
adTAeScuTACACSPlusServContactTimeOut OBJECT-TYPE
SYNTAX Integer32 (1000..30000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"TACACS Plus Server responses time out in milliseconds."
::= { adTAeScuTACACSPlusServerEntry 6 }
adTAeScuTACACSPlusServerPort OBJECT-TYPE
SYNTAX Integer32 (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"TACACS Plus Server port number."
::= { adTAeScuTACACSPlusServerEntry 8 }
adTAeScuTACACSPlusServerAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of adTAeScuTACACSPlusServerInetAddress."
::= { adTAeScuTACACSPlusServerEntry 9 }
adTAeScuTACACSPlusServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"TACACS Plus Server IP address (InetAddress).
Backwards compatibility: Setting this address to a IPv4
address will provision old address adTAeScuTACACSPlusServerAddress
with the new address.
Setting this address to an IPV6 will leave the old provision
address adTAeScuTACACSPlusServerAddress as is."
::= { adTAeScuTACACSPlusServerEntry 10 }
--
--
--
-- End of TACACSPlus Login Config
--
--
END
View Git Blame Copy Permalink