WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/rfc/DVB-RCS-MIB

3330 lines
113 KiB
Plaintext
Raw Permalink Blame History

DVB-RCS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Integer32,
Unsigned32,
transmission
FROM SNMPv2-SMI -- [RFC2578]
TEXTUAL-CONVENTION,
RowStatus
FROM SNMPv2-TC -- [RFC2579]
OBJECT-GROUP,
MODULE-COMPLIANCE
FROM SNMPv2-CONF -- [RFC2580]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
InetAddressType,
InetAddress,
InetAddressPrefixLength,
InetPortNumber
FROM INET-ADDRESS-MIB -- [RFC4001]
Uri
FROM URI-TC-MIB -- [RFC5017]
Dscp,
DscpOrAny
FROM DIFFSERV-DSCP-TC -- [RFC3289]
;
dvbRcsMib MODULE-IDENTITY
LAST-UPDATED "201002161200Z"
ORGANIZATION "The SatLabs Group"
CONTACT-INFO
"The SatLabs Group
Web: www.satlabs.org
E-mail: info@satlabs.org"
DESCRIPTION
"DVB-RCS MIB subtree.
This MIB module applies to equipment that is a Return
Channel Satellite Terminal (RCST), defined in the Digital
Video Broadcasting Return Channel via Satellite system
(DVB-RCS) standard (ETSI EN 301 790 Digital Video
Broadcasting (DVB); Interaction Channel for Satellite
Distribution Systems, European Telecommunications
Standards Institute (ETSI)).
It defines a set of MIB objects to characterize the
behavior and performance of network-layer entities
implementing DVB-RCS.
This MIB module is intended to be used by DVB-RCS
equipment following the SatLabs System Recommendations,
defined by the SatLabs Group and available at
www.satlabs.org.
Note that, if not stated otherwise in the object
DESCRIPTION clause, all writable objects are
persistent.
Copyright (C) The IETF Trust (2010). This version of
this MIB module is part of RFC 5728; see the RFC itself
for full legal notices."
REVISION "200907201200Z"
DESCRIPTION
"Revision of this MIB module, following MIB doctor review
and adjustments based on the MIB authoring guidelines
from the IETF."
::= { transmission 239 }
--==============================================================
-- Textual Conventions
--==============================================================
DvbRcsSatLabsProfileMap ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention enumerates the declaration of
the SatLabs-defined terminal profiles. The mapping to
the profiles is to be understood as described here. (0)
refers to the most significant bit.
dvbs(0) -> DVBS profile (DVB-S support)
dvbs2ccm(1) -> DVB-S2 CCM profile (CCM support)
dvbs2acm(2) -> DVB-S2 ACM profile (CCM, VCM and ACM
support)"
REFERENCE
"SatLabs System Recommendations, available at
www.satlabs.org."
SYNTAX BITS {
dvbs(0),
dvbs2ccm(1),
dvbs2acm(2),
spare1(3),
spare2(4),
spare3(5),
spare4(6),
spare5(7),
spare6(8),
spare7(9),
spare8(10),
spare9(11),
spare10(12),
spare11(13),
spare12(14),
spare13(15),
spare14(16),
spare15(17),
spare16(18),
spare17(19),
spare18(20),
spare19(21),
spare20(22),
spare21(23),
spare22(24),
spare23(25),
spare24(26),
spare25(27),
spare26(28),
spare27(29),
spare28(30),
spare29(31)
}
DvbRcsSatLabsOptionMap ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention enumerates the declaration of
the SatLabs-defined options. A value of 1 indicates
that the respective option is supported. The mapping
to the options is to be understood as described here.
(0) refers to the most significant bit.
mpegTrf(0) -> MPEG_TRF
coarseSync(1) -> COARSE_SYNC
wideHop(2) -> WIDE_HOPP
fastHop(3) -> FAST_HOPP
dynamicMfTdma(4) -> Dynamic_MF_TDMA
contentionSync(5) -> CONTENTION_SYNC
qpskLow(6) -> QPSKLOW
mod16Apsk(7) -> 16APSK
mod32Apsk(8) -> 32APSK
normalFec(9) -> NORMALFEC
multiTs(10) -> MULTITS
gsTs(11) -> GSTS
enhQoS(12) -> ENHQOS
pep(13) -> PEP
http(14) -> HTTP
ftp(15) -> FTP
dns(16) -> DNS
chIdStrict(17) -> CHID_STRICT
nlid(18) -> NLID
snmpMisc(19) -> SNMPMISC
The support of specific options mandates the support of
specific objects and access levels."
REFERENCE
"SatLabs System Recommendations, available at
www.satlabs.org."
SYNTAX BITS {
mpegTrf(0),
coarseSync(1),
wideHop(2),
fastHop(3),
dynamicMfTdma(4),
contentionSync(5),
qpskLow(6),
mod16Apsk(7),
mod32Apsk(8),
normalFec(9),
multiTs(10),
gsTs(11),
enhQoS(12),
pep(13),
http(14),
ftp(15),
dns(16),
chIdStrict(17),
nlid(18),
snmpMisc(19),
spare1(20),
spare2(21),
spare3(22),
spare4(23),
spare5(24),
spare6(25),
spare7(26),
spare8(27),
spare9(28),
spare10(29),
spare11(30),
spare12(31)
}
DvbRcsSatLabsFeatureMap ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention enumerates the declaration
of the SatLabs-specified compatibility and
configuration features. A value of 1 indicates that
the respective feature is supported. The mapping to
the features is to be understood as described here.
(0) refers to the most significant bit.
rcstPara(0) -> RCST_PARA feature
installLog(1) -> INSTALL_LOG feature
enhClassifier(2) -> ENHCLASSIFIER feature
routeId(3) -> ROUTE_ID feature
oduList(4) -> ODULIST feature
extNetwork(5) -> EXTNETWORK feature
extControl(6) -> EXTCONTROL feature
extConfig(7) -> EXTCONFIG feature
extStatus(8) -> EXTSTATUS feature
mpaf(9) -> MPAF feature
The support of specific features mandates the support of
specific objects and access levels."
REFERENCE
"SatLabs System Recommendations, available at
www.satlabs.org."
SYNTAX BITS {
rcstPara(0),
installLog(1),
enhClassifier(2),
routeId(3),
oduList(4),
extNetwork(5),
extControl(6),
extConfig(7),
extStatus(8),
mpaf(9),
spare1(10),
spare2(11),
spare3(12),
spare4(13),
spare5(14),
spare6(15),
spare7(16),
spare8(17),
spare9(18),
spare10(19),
spare11(20),
spare12(21),
spare13(22),
spare14(23),
spare15(24),
spare16(25),
spare17(26),
spare18(27),
spare19(28),
spare20(29),
spare21(30),
spare22(31)
}
--==============================================================
-- object type definitions
--==============================================================
dvbRcsMibObjects OBJECT IDENTIFIER ::= {dvbRcsMib 1}
dvbRcsConformance OBJECT IDENTIFIER ::= {dvbRcsMib 2}
dvbRcsRcst OBJECT IDENTIFIER ::= {dvbRcsMibObjects 1}
dvbRcsFwdLink OBJECT IDENTIFIER ::= {dvbRcsMibObjects 2}
dvbRcsRtnLink OBJECT IDENTIFIER ::= {dvbRcsMibObjects 3}
dvbRcsRcstSystem OBJECT IDENTIFIER ::= {dvbRcsRcst 1}
dvbRcsRcstNetwork OBJECT IDENTIFIER ::= {dvbRcsRcst 2}
dvbRcsRcstInstall OBJECT IDENTIFIER ::= {dvbRcsRcst 3}
dvbRcsRcstQos OBJECT IDENTIFIER ::= {dvbRcsRcst 4}
dvbRcsRcstControl OBJECT IDENTIFIER ::= {dvbRcsRcst 5}
dvbRcsRcstState OBJECT IDENTIFIER ::= {dvbRcsRcst 6}
dvbRcsFwdConfig OBJECT IDENTIFIER ::= {dvbRcsFwdLink 1}
dvbRcsFwdStatus OBJECT IDENTIFIER ::= {dvbRcsFwdLink 2}
dvbRcsRtnConfig OBJECT IDENTIFIER ::= {dvbRcsRtnLink 1}
dvbRcsRtnStatus OBJECT IDENTIFIER ::= {dvbRcsRtnLink 2}
--==============================================================
-- dvbRcsRcstSystem sub-tree object types
--==============================================================
dvbRcsSystemMibRevision OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object allows the SNMP agent to report the
implemented MIB module revision.
The supported REVISION of this module is reported."
::= {dvbRcsRcstSystem 1}
--==============================================================
-- Options declared according to the textual conventions
--==============================================================
dvbRcsSystemSatLabsProfilesDeclaration OBJECT-TYPE
SYNTAX DvbRcsSatLabsProfileMap
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the SatLabs profiles supported, as defined in
the SatLabs System Recommendations."
::= {dvbRcsRcstSystem 2}
dvbRcsSystemSatLabsOptionsDeclaration OBJECT-TYPE
SYNTAX DvbRcsSatLabsOptionMap
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the SatLabs options supported, as defined in
the SatLabs System Recommendations."
::= {dvbRcsRcstSystem 3}
dvbRcsSystemSatLabsFeaturesDeclaration OBJECT-TYPE
SYNTAX DvbRcsSatLabsFeatureMap
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the optional compatibility features and minor
options supported, as defined in the SatLabs System
Recommendations."
::= {dvbRcsRcstSystem 4}
dvbRcsSystemLocation OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Physical location of the ODU antenna expressed as
longitude, latitude, and altitude. The string
shall have 31 characters in the following format:
<xxxx.xxx>,<a>,<yyyyy.yyy>,<b>,<zzzz.z>,M
where x, y and z represents digits,
a=N or S,
b=E or W,
Reading the digits from left to right:
'x' 7 latitude digits;
x digits 1-2 contain the degrees,
x digits 3-7 contain the minutes in decimal;
'y' 8 longitude digits;
y digits 1-3 contain the degrees,
y digits 4-8 contain the minutes in decimal;
'z' 5 altitude digits;
meters above sea level in decimal;
'.' is the decimal point;
',' is the field separator;
'M' is the indicator for altitude meters.
This format is a modified subset of the NMEA 0183
(National Marine Electronics Association, Interface
Standard) format for Global Positioning System Fix
Data.
This location and the satellite position are used to
calculate the RCST-satellite path delay.
Note: The system.sysLocation object of MIB-II provides
physical location of the IDU unit."
::= {dvbRcsRcstSystem 5}
dvbRcsSystemOduAntennaSize OBJECT-TYPE
SYNTAX Unsigned32
UNITS "cm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Diameter of the antenna."
::= {dvbRcsRcstSystem 6}
dvbRcsSystemOduAntennaGain OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dBi"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Antenna peak gain of the ODU."
::= {dvbRcsRcstSystem 7}
dvbRcsSystemOduSspa OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 W"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Power level of the Solid State Power Amplifier
installed in the ODU."
::= {dvbRcsRcstSystem 8}
dvbRcsSystemOduTxType OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of transmitter installed in the ODU."
::= {dvbRcsRcstSystem 9}
dvbRcsSystemOduRxType OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Type of LNB installed in the ODU, with
information such as vendor type, output type (single,
twin, quad,...), etc."
::= {dvbRcsRcstSystem 10}
dvbRcsSystemOduRxBand OBJECT-TYPE
SYNTAX INTEGER {
oduHighRxBand (0),
oduLowRxBand (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"LNB High Band / Low Band selector. High Band corresponds
to the emission of an 18-26 kHz tone with 0.4-0.8 Vpp in
the Rx IFL cable:
(0) - High Band
(1) - Low Band"
::= {dvbRcsRcstSystem 11}
dvbRcsSystemOduRxLO OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Frequency of LNB Local Oscillator (in 100 Hz)"
::= {dvbRcsRcstSystem 12}
dvbRcsSystemOduTxLO OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Frequency of Block Up-Converter Local Oscillator
(in 100 Hz)."
::= {dvbRcsRcstSystem 13}
dvbRcsSystemIduPep OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 14}
dvbRcsTcpPep OBJECT-TYPE
SYNTAX INTEGER{
disabled (0),
enabled (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Status and control of embedded TCP PEP.
0 - disabled or not implemented
1 - enabled"
::={dvbRcsSystemIduPep 1}
dvbRcsHttpPep OBJECT-TYPE
SYNTAX INTEGER{
disabled (0),
enabled (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Status and control of embedded HTTP PEP.
0 - disabled or not implemented
1 - enabled"
::={dvbRcsSystemIduPep 2}
--==============================================================
-- ODU structural entities
--==============================================================
dvbRcsOduTx OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 15}
dvbRcsOduRx OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 16}
dvbRcsOduAntenna OBJECT IDENTIFIER ::= {dvbRcsRcstSystem 17}
--==============================================================
-- ODU BUC
--==============================================================
dvbRcsOduTxTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsOduTxTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the identification of each well-
known BUC type supported by the IDU and provides its
associated index."
::={dvbRcsOduTx 1}
dvbRcsOduTxTypeEntry OBJECT-TYPE
SYNTAX DvbRcsOduTxTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the BUC type table."
INDEX { dvbRcsOduTxTypeIndex }
::={dvbRcsOduTxTypeTable 1}
DvbRcsOduTxTypeEntry ::= SEQUENCE {
dvbRcsOduTxTypeIndex Unsigned32,
dvbRcsOduTxTypeDescription SnmpAdminString
}
dvbRcsOduTxTypeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the BUC type."
::={dvbRcsOduTxTypeEntry 1}
dvbRcsOduTxTypeDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Text-based identification of a BUC type."
::={dvbRcsOduTxTypeEntry 2}
dvbRcsOduTxType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Index of the selected BUC type."
::={dvbRcsOduTx 2}
--==============================================================
-- ODU LNB
--==============================================================
dvbRcsOduRxTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsOduRxTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the identification of each well-
known LNB type supported by the IDU and provides its
associated index."
::={dvbRcsOduRx 1}
dvbRcsOduRxTypeEntry OBJECT-TYPE
SYNTAX DvbRcsOduRxTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the LNB type table."
INDEX { dvbRcsOduRxTypeIndex }
::={dvbRcsOduRxTypeTable 1}
DvbRcsOduRxTypeEntry ::= SEQUENCE {
dvbRcsOduRxTypeIndex Unsigned32,
dvbRcsOduRxTypeDescription SnmpAdminString
}
dvbRcsOduRxTypeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the LNB type."
::={dvbRcsOduRxTypeEntry 1}
dvbRcsOduRxTypeDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Text-based identification of an LNB type."
::={dvbRcsOduRxTypeEntry 2}
dvbRcsOduRxType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Index of the selected LNB type."
::={dvbRcsOduRx 2}
--==============================================================
-- ODU Antenna
--==============================================================
dvbRcsOduAntennaTypeTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsOduAntennaTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the identification of each well-
known antenna type supported by the IDU and provides
its associated index."
::={dvbRcsOduAntenna 1}
dvbRcsOduAntennaTypeEntry OBJECT-TYPE
SYNTAX DvbRcsOduAntennaTypeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the antenna type table."
INDEX { dvbRcsOduAntennaTypeIndex }
::={dvbRcsOduAntennaTypeTable 1}
DvbRcsOduAntennaTypeEntry ::= SEQUENCE {
dvbRcsOduAntennaTypeIndex Unsigned32,
dvbRcsOduAntennaTypeDescription SnmpAdminString
}
dvbRcsOduAntennaTypeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the antenna type."
::={dvbRcsOduAntennaTypeEntry 1}
dvbRcsOduAntennaTypeDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Text-based identification of an antenna type."
::={dvbRcsOduAntennaTypeEntry 2}
dvbRcsOduAntennaType OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Index of the selected antenna type."
::={dvbRcsOduAntenna 2}
--==============================================================
-- dvbRcsRcstNetwork sub-tree object types
--==============================================================
dvbRcsNetworkOamInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsNetworkOamInetAddress.
If the terminal OAM Internet address is unassigned or
unknown, then the value of this object is unknown(0)."
::= {dvbRcsRcstNetwork 1}
dvbRcsNetworkOamInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"OAM IP Address of the RCST. This object is used with
both IP and interfaces MIB-II subgroups. It uniquely
determines the interface through which OAM traffic
passes.
The OAM IP address may be statically or dynamically
assigned. It is system dependent whether the OAM IP
address and the Traffic IP address are the same address.
If the terminal has no OAM Internet address assigned or if
this Internet address is unknown, the value of this
object is the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkOamInetAddressType object."
::= {dvbRcsRcstNetwork 2}
dvbRcsNetworkOamInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the OAM IP Address. If this address
prefix is unknown or does not apply, the value is zero."
::= {dvbRcsRcstNetwork 3}
dvbRcsNetworkOamInetAddressAssign OBJECT-TYPE
SYNTAX INTEGER {
oamInetAddressStatic (1),
oamInetAddressDynamic (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Identifies whether the OAM IP address is statically
(1) or dynamically (2) assigned."
::= {dvbRcsRcstNetwork 4}
dvbRcsNetworkLanInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of dvbRcsNetworkLanInetAddress.
If the terminal Internet address on the LAN interface is
unassigned or unknown, then the value of this object is
unknown(0)."
::= {dvbRcsRcstNetwork 5}
dvbRcsNetworkLanInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the LAN interface of the terminal. If the
terminal has no Internet address assigned on the LAN
interface or if this Internet address is unknown, the
value of this object is the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkLanInetAddressType object."
::= {dvbRcsRcstNetwork 6}
dvbRcsNetworkLanInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the LAN IP Address of the terminal.
If this address prefix is unknown or does not apply, the
value is zero."
::= {dvbRcsRcstNetwork 7}
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType
OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress.
If the default gateway Internet address is unassigned or
unknown, then the value of this object is unknown(0)."
::= {dvbRcsRcstNetwork 8}
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the default gateway for the air
interface. If the terminal has no default gateway
assigned on the air interface or if this Internet address
is unknown, the value of this object is the zero-length
OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType
object."
::= {dvbRcsRcstNetwork 9}
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressPrefixLength
OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the default gateway
for the air interface.
If this address prefix is unknown or does not apply, the
value is zero."
::= {dvbRcsRcstNetwork 10}
dvbRcsNetworkDnsServers OBJECT IDENTIFIER ::= {dvbRcsRcstNetwork
11}
dvbRcsPrimaryDnsServerInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsPrimaryDnsServerInetAddress. If the primary DNS
server Internet address is unassigned or unknown, then
the value of this object is unknown(0)."
::= { dvbRcsNetworkDnsServers 1}
dvbRcsPrimaryDnsServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the primary DNS server in the NCC. If
the terminal has no primary DNS server assigned or if this
Internet address is unknown, the value of this object is
the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsPrimaryDnsServerInetAddressType object."
::= {dvbRcsNetworkDnsServers 2}
dvbRcsPrimaryDnsServerInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the primary DNS
server in the NCC.
If this address prefix is unknown or does not apply, the
value is zero."
::= { dvbRcsNetworkDnsServers 3}
dvbRcsSecondaryDnsServerInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsSecondaryDnsServerInetAddress. If the secondary
DNS server Internet address is unassigned or unknown,
then the value of this object is unknown(0)."
::= { dvbRcsNetworkDnsServers 4}
dvbRcsSecondaryDnsServerInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the secondary DNS server in the NCC. If
the terminal has no secondary DNS server assigned or if
this Internet address is unknown, the value of this
object is the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsSecondaryDnsServerInetAddressType object."
::= {dvbRcsNetworkDnsServers 5}
dvbRcsSecondaryDnsServerInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the secondary DNS
server in the NCC.
If this address prefix is unknown or does not apply, the
value is zero."
::= { dvbRcsNetworkDnsServers 6}
dvbRcsNetworkNccMgtInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsNetworkNccMgtInetAddress. If the management server
Internet address is unassigned or unknown, then the
value of this object is unknown(0)."
::= {dvbRcsRcstNetwork 12}
dvbRcsNetworkNccMgtInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IP address of the management server in the NCC. If
the terminal has no management server assigned or if this
Internet address is unknown, the value of this object is
the zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsNetworkNccMgtInetAddressType object."
::= {dvbRcsRcstNetwork 13}
dvbRcsNetworkNccMgtInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Prefix length for the IP address of the management
server in the NCC.
If this address prefix is unknown or does not apply, the
value is zero."
::= { dvbRcsRcstNetwork 14}
dvbRcsNetworkConfigFileDownloadUrl OBJECT-TYPE
SYNTAX Uri (SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path name for the configuration file download.
It includes the protocol type (TFTP or FTP) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 15}
dvbRcsNetworkInstallLogFileDownloadUrl OBJECT-TYPE
SYNTAX Uri (SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the installation log file to download.
It includes the protocol type (TFTP or FTP) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST. The
installation log file can be created on the installer's
computer and downloaded to the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 16}
dvbRcsNetworkConfigFileUploadUrl OBJECT-TYPE
SYNTAX Uri(SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path name for the configuration file upload.
It includes the protocol type (TFTP or FTP) and the
associated server IP address or hostname. Hostname can
only be used if DNS is supported by the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 17}
dvbRcsNetworkLogFileUploadUrl OBJECT-TYPE
SYNTAX Uri(SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the event log file. It includes the
protocol type (TFTP or FTP) and the associated server IP
address or hostname. Hostname can only be used if DNS is
supported by the RCST.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 18}
dvbRcsNetworkInstallLogFileUploadUrl OBJECT-TYPE
SYNTAX Uri(SIZE(0..65535))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Full path of the installation log file. It includes the
protocol type (TFTP or FTP) and the associated server
IP address or hostname. Hostname can only be used if DNS
is supported by the RCST. The installation log file can
be retrieved from the RCST by the NCC or by the
installer via the LAN.
The format of this parameter follows RFC 3986."
::= {dvbRcsRcstNetwork 19}
--==============================================================
-- dvbRcsRcstInstall sub-tree object types
--==============================================================
dvbRcsInstallAntennaAlignmentState OBJECT-TYPE
SYNTAX INTEGER {
antennaAlignmentStart (1),
antennaAlignmentDeny (2),
antennaAlignmentContinue(3),
antennaAlignmentStop (4),
antennaAlignmentSuccess (5),
antennaAlignmentFail (6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the alignment state of the antenna:
(1)-Start;
(2)-Deny;
(3)-Continue;
(4)-Stop;
(5)-Success;
(6)-Fail"
::= {dvbRcsRcstInstall 1}
dvbRcsInstallCwFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 Hz"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Frequency of the transmitted Continuous Wave
carrier (in 100 Hz).
Minimum required precision is 1 kHz."
::= {dvbRcsRcstInstall 2}
dvbRcsInstallCwMaxDuration OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time after which the Continuous Wave carrier must be
put down (in seconds)."
::= {dvbRcsRcstInstall 3}
dvbRcsInstallCwPower OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IDU TX output level when the IDU is configured to send
CW. The resolution is 0.1 dBm and the accuracy is +/- 1
dBm. Reconfiguration is applied immediately to a CW."
::= {dvbRcsRcstInstall 4}
dvbRcsInstallCoPolReading OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Co-polarization measured value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 5}
dvbRcsInstallXPolReading OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Cross-polarization measured value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 6}
dvbRcsInstallCoPolTarget OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Co-polarization target value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 7}
dvbRcsInstallXPolTarget OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Cross-polarization target value during installation
procedure (in 0.1 dB)."
::= {dvbRcsRcstInstall 8}
dvbRcsInstallStandByDuration OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time to wait in stand-by mode (in seconds)."
::= {dvbRcsRcstInstall 9}
dvbRcsInstallTargetEsN0 OBJECT-TYPE
SYNTAX Unsigned32(0..315)
UNITS "x0.1 dB"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This value describes the wanted Es/N0 value that
enables operation of the return link with the required
error performance. The values shall be given in tenth of
dB and the initial value shall be equal to 7 dB. The
range shall be from 0 dB to 31.5 dB, with a precision
of 0.1 dB."
DEFVAL { 70 }
::= {dvbRcsRcstInstall 10}
--==============================================================
-- dvbRcsRcstQos sub-tree object types
--==============================================================
dvbRcsPktClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsPktClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the packet classification used in
the DVB-RCS terminal. The number of entries is specified
by dvbRcsPktClassIndex. "
::={dvbRcsRcstQos 1}
dvbRcsPktClassEntry OBJECT-TYPE
SYNTAX DvbRcsPktClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the packet classification table. One object
type of each entry may have a value in the active range
(a non-default value). The other object types are then
assumed to be set to 'inactive'. The entry with the lowest
index value takes precedence when classifying a packet."
INDEX { dvbRcsPktClassIndex }
::= {dvbRcsPktClassTable 1}
DvbRcsPktClassEntry ::= SEQUENCE {
dvbRcsPktClassIndex Unsigned32,
dvbRcsPktClassDscpLow Dscp,
dvbRcsPktClassDscpHigh Dscp,
dvbRcsPktClassDscpMarkValue DscpOrAny,
dvbRcsPktClassIpProtocol Unsigned32,
dvbRcsPktClassSrcInetAddressType InetAddressType,
dvbRcsPktClassSrcInetAddress InetAddress,
dvbRcsPktClassSrcInetAddressPrefixLength
InetAddressPrefixLength,
dvbRcsPktClassDstInetAddressType InetAddressType,
dvbRcsPktClassDstInetAddress InetAddress,
dvbRcsPktClassDstInetAddressPrefixLength
InetAddressPrefixLength,
dvbRcsPktClassSrcPortLow InetPortNumber,
dvbRcsPktClassSrcPortHigh InetPortNumber,
dvbRcsPktClassDstPortLow InetPortNumber,
dvbRcsPktClassDstPortHigh InetPortNumber,
dvbRcsPktClassVlanUserPri Integer32,
dvbRcsPktClassPhbAssociation Unsigned32,
dvbRcsPktClassRowStatus RowStatus
}
dvbRcsPktClassIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..64)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index automatically incremented by one at row
creation."
::={dvbRcsPktClassEntry 1}
dvbRcsPktClassDscpLow OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low value of a range of
Diffserv Code Point (DSCP) values to which a packet is
compared."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 2}
dvbRcsPktClassDscpHigh OBJECT-TYPE
SYNTAX Dscp
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high value of a range of
Diffserv Code Point (DSCP) values to which a packet is
compared."
DEFVAL { 63 }
::={dvbRcsPktClassEntry 3}
dvbRcsPktClassDscpMarkValue OBJECT-TYPE
SYNTAX DscpOrAny
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is the Diffserv Code Point (DSCP) value
used to mark the packet; -1 indicates no DSCP marking.
Possible DSCP marks values are (0..63)"
DEFVAL { -1 }
::={dvbRcsPktClassEntry 4}
dvbRcsPktClassIpProtocol OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP protocol to which a
packet is compared. A value of 255 means match all."
DEFVAL { 255 }
::={dvbRcsPktClassEntry 5}
dvbRcsPktClassSrcInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsPktClassSrcInetAddress. If the packet class source
Internet address is unassigned or unknown, then the
value of this object is unknown(0)."
::= { dvbRcsPktClassEntry 6}
dvbRcsPktClassSrcInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP source address to which a
packet is compared. If the packet class has no source
Internet address assigned or if this Internet address is
unknown, the value of this object is the zero-length
OCTET STRING.
The InetAddressType is given by the
dvbRcsPktClassSrcInetAddressType object."
::={dvbRcsPktClassEntry 7}
dvbRcsPktClassSrcInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Prefix length of the IP source address that will be
matched for this packet class. A value of zero indicates
that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 8}
dvbRcsPktClassDstInetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of Internet address of
dvbRcsPktClassDstInetAddress. If the packet class
destination Internet address is unassigned or unknown,
then the value of this object is unknown(0)."
::= { dvbRcsPktClassEntry 9}
dvbRcsPktClassDstInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the IP destination address to
which a packet is compared. If the packet class has no
destination Internet address assigned or if this Internet
address is unknown, the value of this object is the
zero-length OCTET STRING.
The InetAddressType is given by the
dvbRcsPktClassDstInetAddressType object."
::={dvbRcsPktClassEntry 10}
dvbRcsPktClassDstInetAddressPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Prefix length of the IP source address that will be
matched for this packet class. A value of zero indicates
that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 11}
dvbRcsPktClassSrcPortLow OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low range of the source
port to which a packet is compared. A value of 0
indicates that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 12}
dvbRcsPktClassSrcPortHigh OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high range of the source port
to which a packet is compared. A value of 0 indicates
that the selectivity is inactive."
DEFVAL { 65535 }
::={dvbRcsPktClassEntry 13}
dvbRcsPktClassDstPortLow OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the low range of the destination
port to which a packet is compared. A value of 0
indicates that the selectivity is inactive."
DEFVAL { 0 }
::={dvbRcsPktClassEntry 14}
dvbRcsPktClassDstPortHigh OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the high range of the destination
port to which a packet is compared. A value of 0
indicates that the selectivity is inactive."
DEFVAL { 65535 }
::={dvbRcsPktClassEntry 15}
dvbRcsPktClassVlanUserPri OBJECT-TYPE
SYNTAX Integer32 (-1..7)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the VLAN User Priority to which a
packet is compared. A value of -1 indicates that the
selectivity is inactive."
DEFVAL { -1 }
::={dvbRcsPktClassEntry 16}
dvbRcsPktClassPhbAssociation OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Associate the filter entry to a specific PHB (refer to
dvbRcsPhbIdentifier)."
::={dvbRcsPktClassEntry 17}
dvbRcsPktClassRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable objects
in this row may be modified at any time."
::={dvbRcsPktClassEntry 18}
--==============================================================
-- dvbRcsPhbMappingTable
--==============================================================
dvbRcsPhbMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsPhbMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a list of Per-Hop Behavior (PHB) MIB
entries.
It describes the PHB mapping to the Request Class."
::={dvbRcsRcstQos 2}
dvbRcsPhbMappingEntry OBJECT-TYPE
SYNTAX DvbRcsPhbMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the PHB mapping table."
INDEX {dvbRcsPhbIdentifier}
::= {dvbRcsPhbMappingTable 1}
DvbRcsPhbMappingEntry ::= SEQUENCE {
dvbRcsPhbIdentifier Unsigned32,
dvbRcsPhbName
SnmpAdminString,
dvbRcsPhbRequestClassAssociation Unsigned32,
dvbRcsPhbMappingRowStatus RowStatus
}
dvbRcsPhbIdentifier OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identification of the Per-Hop Behavior (PHB). It
follows the unsigned 16-bit binary encoding as specified
in RFC 3140. The value 0 designates the Default PHB."
::={dvbRcsPhbMappingEntry 1}
dvbRcsPhbName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name of the Per-Hop Behavior (PHB)."
::={dvbRcsPhbMappingEntry 2}
dvbRcsPhbRequestClassAssociation OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is an association of this Per-Hop Behavior
(PHB) to a Request Class (by reference to a Request
Class index)."
::={dvbRcsPhbMappingEntry 3}
dvbRcsPhbMappingRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable
objects in this row may be modified at any time."
DEFVAL { active }
::={dvbRcsPhbMappingEntry 4}
--==============================================================
-- dvbRcsRequestClassTable
--==============================================================
dvbRcsRequestClassTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsRequestClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a list of Request Class entries. This
class describes the layer 2 QoS objects."
::={dvbRcsRcstQos 3}
dvbRcsRequestClassEntry OBJECT-TYPE
SYNTAX DvbRcsRequestClassEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Request Class table."
INDEX {dvbRcsRequestClassIndex}
::= {dvbRcsRequestClassTable 1}
DvbRcsRequestClassEntry ::= SEQUENCE {
dvbRcsRequestClassIndex Unsigned32,
dvbRcsRequestClassName
SnmpAdminString,
dvbRcsRequestClassChanId Unsigned32,
dvbRcsRequestClassVccVpi Unsigned32,
dvbRcsRequestClassVccVci Unsigned32,
dvbRcsRequestClassPidPoolReference Unsigned32,
dvbRcsRequestClassCra Unsigned32,
dvbRcsRequestClassRbdcMax Unsigned32,
dvbRcsRequestClassRbdcTimeout Unsigned32,
dvbRcsRequestClassVbdcMax Unsigned32,
dvbRcsRequestClassVbdcTimeout Unsigned32,
dvbRcsRequestClassVbdcMaxBackLog Unsigned32,
dvbRcsRequestClassRowStatus RowStatus
}
dvbRcsRequestClassIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the Request Class table. A total of 16 entries
are supported."
::={dvbRcsRequestClassEntry 1}
dvbRcsRequestClassName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Name of the Request Class."
::={dvbRcsRequestClassEntry 2}
dvbRcsRequestClassChanId OBJECT-TYPE
SYNTAX Unsigned32 (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Channel ID of the Request Class."
::={dvbRcsRequestClassEntry 3}
dvbRcsRequestClassVccVpi OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the VPI used for the Request Class (ATM profile)."
::={dvbRcsRequestClassEntry 4}
dvbRcsRequestClassVccVci OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the VCI used for the Request Class (ATM profile)."
::={dvbRcsRequestClassEntry 5}
dvbRcsRequestClassPidPoolReference OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Reference to the Packet IDentifier (PID) pool
applicable for the Request Class."
::={dvbRcsRequestClassEntry 6}
dvbRcsRequestClassCra OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bit/s"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the Continuous Rate Assignment (CRA) level for the
Request Class in bits per second (bit/s)."
::={dvbRcsRequestClassEntry 7}
dvbRcsRequestClassRbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x2 kbit/s"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Rate-Based Dynamic Capacity (RBDC) that can be
requested for the Request Class, in number of 2 kbit/s."
::={dvbRcsRequestClassEntry 8}
dvbRcsRequestClassRbdcTimeout OBJECT-TYPE
SYNTAX Unsigned32
UNITS "superframes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Persistence of the Rate-Based Dynamic Capacity (RBDC)
request, expressed in superframes."
::={dvbRcsRequestClassEntry 9}
dvbRcsRequestClassVbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "ATM cells/MPEG packets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Volume-Based Dynamic Capacity (VBDC) that can
be allocated to the Request Class, in payload units (one
ATM cell or one MPEG packet) per superframe."
::={dvbRcsRequestClassEntry 10}
dvbRcsRequestClassVbdcTimeout OBJECT-TYPE
SYNTAX Unsigned32
UNITS "superframes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Time after which the RCST considers that the pending
requests are lost. The RCST may issue new requests for
that traffic. Volume-Based Dynamic Capacity (VBDC)
Timeout is expressed in superframes."
::={dvbRcsRequestClassEntry 11}
dvbRcsRequestClassVbdcMaxBackLog OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Volume-Based Dynamic Capacity (VBDC) back log per
Request Class (expressed in bytes)."
::={dvbRcsRequestClassEntry 12}
dvbRcsRequestClassRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. It is not possible
to change values in a row of this table while the row is
active."
::={dvbRcsRequestClassEntry 13}
--==============================================================
-- The table of PID pools
--==============================================================
dvbRcsPidPoolTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsPidPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the Packet IDentifier (PID) pools.
For the MPEG profile, several Request Classes may be mapped
within a pool of several PIDs to allow Section Packing
across several Request Classes.
A PID value may occur in more than one PID pool. Each
PID value can effectively occur only once in each pool."
::={dvbRcsRcstQos 4}
dvbRcsPidPoolEntry OBJECT-TYPE
SYNTAX DvbRcsPidPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the PID pool table."
INDEX { dvbRcsPidPoolIndex, dvbRcsPidIndex }
::= {dvbRcsPidPoolTable 1}
DvbRcsPidPoolEntry ::= SEQUENCE {
dvbRcsPidPoolIndex Unsigned32,
dvbRcsPidIndex Unsigned32,
dvbRcsPidValue Unsigned32,
dvbRcsPidPoolRowStatus RowStatus
}
dvbRcsPidPoolIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the PID pool in the PID pool table."
::={dvbRcsPidPoolEntry 1}
dvbRcsPidIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the PID entry within the PID pool."
::={dvbRcsPidPoolEntry 2}
dvbRcsPidValue OBJECT-TYPE
SYNTAX Unsigned32 (0..8191)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines one of the PIDs to be used in a PID pool of
dvbRcsPidPoolIndex.
A PID value may occur in more than one PID pool. Each
PID value can effectively occur only once in each pool."
::={dvbRcsPidPoolEntry 3}
dvbRcsPidPoolRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable
objects in this row may be modified at any time."
DEFVAL { active }
::={dvbRcsPidPoolEntry 4}
dvbRcsQosGlobalRbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x2 kbit/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global maximum RBDC that can be requested for the RCST,
in number of 2 kbit/s."
::={dvbRcsRcstQos 5}
dvbRcsQosGlobalVbdcMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "ATM cells/MPEG packets"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global maximum VBDC that can be allocated to the RCST,
in payload units (one ATM cell or one MPEG packet) per
superframe."
::={dvbRcsRcstQos 6}
dvbRcsQosGlobalVbdcMaxBackLog OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global VBDC back log at the RCST level (expressed in
bytes). It is used only if the VBDC back log is not
configured in the Request Class (expressed in bytes)."
::={dvbRcsRcstQos 7}
dvbRcsQosChannelIdStrictDispatching OBJECT-TYPE
SYNTAX INTEGER {
notStrict (0),
strict (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the RCST will strictly follow RC
association when signaled through Channel_ID in the
TBTP:
(0)- no strict association
(1)- strict association"
::={dvbRcsRcstQos 8}
--==============================================================
-- dvbRcsRcstControl sub-tree object types
--==============================================================
dvbRcsCtrlRebootCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
normal (2),
alternate (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall force the RCST to reboot:
(1)- idle
(2)- normal reboot (from current software load)
(3)- reboot from alternate load (swap to alternate
load before reboot)"
DEFVAL {idle}
::={dvbRcsRcstControl 1}
dvbRcsCtrlRcstTxDisable OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall force the RCST to stop transmission
(transmit disabled as defined in SatLabs System
Recommendations):
(1)- idle
(2)- initiate Tx Disabled"
DEFVAL {idle}
::={dvbRcsRcstControl 2}
dvbRcsCtrlUserTrafficDisable OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable shall disable user traffic (only RCST
management traffic can be transmitted):
(1)- idle
(2)- disable user traffic"
DEFVAL {idle}
::={dvbRcsRcstControl 3}
dvbRcsCtrlCwEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will force the RCST to start transmission
of CW, if the RCST is first set to the installation
state and is properly configured for CW transmission:
(1)- off
(2)- on"
DEFVAL {off}
::={dvbRcsRcstControl 4}
dvbRcsCtrlOduTxReferenceEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of the 10 MHz reference
clock in the Tx IFL cable:
(1) off
(2) on"
DEFVAL {on}
::={dvbRcsRcstControl 5}
dvbRcsCtrlOduTxDCEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of DC in the Tx IFL
cable:
(1) off
(2) on"
DEFVAL {on}
::={dvbRcsRcstControl 6}
dvbRcsCtrlOduRxDCEnable OBJECT-TYPE
SYNTAX INTEGER {
off (1),
on (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables activation and deactivation of DC in the Rx IFL
cable:
(1) off
(2) on"
DEFVAL {on}
::={dvbRcsRcstControl 7}
dvbRcsCtrlDownloadFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
config (2),
installationLog (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST configuration file
download process:
(1) idle
(2) download RCST configuration file from TFTP/FTP
server
(3) download RCST installation log file from TFTP/FTP
server (INSTALL_LOG feature)"
DEFVAL {idle}
::={dvbRcsRcstControl 8}
dvbRcsCtrlUploadFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
config (2),
eventAlarm (3),
installationLog (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST upload process:
(1) idle
(2) upload RCST configuration file to TFTP/FTP server
(3) upload RCST event/alarm log file to TFTP/FTP server
(4) upload RCST installation log file to TFTP/FTP server
(INSTALL_LOG feature)"
DEFVAL {idle}
::={dvbRcsRcstControl 9}
dvbRcsCtrlActivateConfigFileCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
activate (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Triggers the RCST to use the configuration file and
update its parameters accordingly. Some RCST
implementations may require a reboot for the parameters
to take effect (vendor specific).
(1) idle
(2) activate"
DEFVAL {idle}
::={dvbRcsRcstControl 10}
dvbRcsCtrlRcstLogonCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
logon (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST logon:
(1) idle
(2) initiate RCST logon"
DEFVAL {idle}
::={dvbRcsRcstControl 11}
dvbRcsCtrlRcstLogoffCommand OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
logoff (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will initiate an RCST logoff:
(1) idle
(2) initiate RCST logoff"
DEFVAL {idle}
::={dvbRcsRcstControl 12}
dvbRcsCtrlRcstRxReacquire OBJECT-TYPE
SYNTAX INTEGER {
idle (1),
reacquireForwardLink (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable will force the RCST to acquire the
forward link and start receiving:
(1) idle
(2) reacquire forward link"
DEFVAL {idle}
::={dvbRcsRcstControl 13}
--==============================================================
-- dvbRcsRcstState sub-tree object types
--==============================================================
dvbRcsRcstMode OBJECT-TYPE
SYNTAX INTEGER {
installation (0),
operational (1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Identifies the current mode of the RCST and allows the RCST
to return to the installation mode when needed. Values for
the RCST mode are:
Installation (0)
Operational (1)"
::={dvbRcsRcstState 1}
dvbRcsRcstFaultStatus OBJECT-TYPE
SYNTAX INTEGER {
nofault (0),
fault (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the fault status of the terminal. The fault
status management is vendor specific. Values for the
fault status are:
no fault (0)
fault (1)"
::={dvbRcsRcstState 2}
dvbRcsRcstFwdLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
notAcquired (0),
acquired (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the status of the RCST forward link. Values
for the forward link status are:
Not acquired (0)
Acquired (1)"
::={dvbRcsRcstState 3}
dvbRcsRcstRtnLinkStatus OBJECT-TYPE
SYNTAX INTEGER {
loggedOff (0),
loggedOn (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the status of the RCST return link. Values for
the return link status are:
Logged-off (0)
Logged-on (1)"
::={dvbRcsRcstState 4}
dvbRcsRcstLogUpdated OBJECT-TYPE
SYNTAX INTEGER {
noUpdate (0),
logfileUpdated (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the existence of an updated event log file:
No update (0)
Event Log file updated (1)
The RCST should remove the 'Event Log file updated'
indication as the log file is fetched by the NCC."
::={dvbRcsRcstState 5}
dvbRcsRcstCurrentSoftwareVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current RCST software version."
::={dvbRcsRcstState 6}
dvbRcsRcstAlternateSoftwareVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Alternate (backup/new) RCST software version."
::={dvbRcsRcstState 7}
dvbRcsRcstActivatedConfigFileVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the most recently activated configuration
file.
The version is vendor specific."
::={dvbRcsRcstState 8}
dvbRcsRcstDownloadedConfigFileVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the most recently downloaded configuration
file.
Version is vendor specific. If the value is different
from dvbRcsRcstActivatedConfigFileVersion, it is pending
for activation."
::={dvbRcsRcstState 9}
--==============================================================
-- dvbRcsFwdConfig sub-tree object types
--==============================================================
dvbRcsFwdStartTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsFwdStartEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Lists forward link attachment points (e.g., different
for installation and operation).
The table describes the forward link parameters used for
the start-up stream with the NCC."
::={dvbRcsFwdConfig 1}
dvbRcsFwdStartEntry OBJECT-TYPE
SYNTAX DvbRcsFwdStartEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the Forward Link Start Configuration table."
INDEX {dvbRcsFwdStartIndex}
::= {dvbRcsFwdStartTable 1}
DvbRcsFwdStartEntry ::= SEQUENCE {
dvbRcsFwdStartIndex Unsigned32,
dvbRcsFwdStartPopId Integer32,
dvbRcsFwdStartFrequency Unsigned32,
dvbRcsFwdStartPolar INTEGER,
dvbRcsFwdStartFormat INTEGER,
dvbRcsFwdStartRolloff INTEGER,
dvbRcsFwdStartSymbolRate Unsigned32,
dvbRcsFwdStartInnerFec INTEGER,
dvbRcsFwdStartRowStatus RowStatus
}
dvbRcsFwdStartIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the Forward Link StartConfig table."
::={dvbRcsFwdStartEntry 1}
dvbRcsFwdStartPopId OBJECT-TYPE
SYNTAX Integer32 (-1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Population identifier associated with the start-up
forward link:
-1: any (auto)
0-65535: specific StartPopId
If 'any' is set, the RCST will assume membership of any
announced population ID and will commence with logon in
accordance with this assumption."
::={dvbRcsFwdStartEntry 2}
dvbRcsFwdStartFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Frequency of the start transponder carrying a
Network Information Table to which any RCST shall
trigger to acquire forward link. Its value shall be
given in multiples of 100 kHz."
::={dvbRcsFwdStartEntry 3}
dvbRcsFwdStartPolar OBJECT-TYPE
SYNTAX INTEGER {
linearHorizontal (0),
linearVertical (1),
circularLeft (2),
circularRight (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"2-bit field giving the polarization of the start
transponder carrying a Network Information Table to
which any RCST shall trigger to acquire forward link:
00: linear and horizontal
01: linear and vertical
10: circular left
11: circular right"
::={dvbRcsFwdStartEntry 4}
dvbRcsFwdStartFormat OBJECT-TYPE
SYNTAX INTEGER {
auto (-1),
dvbs (0),
dvbs2ccm (1),
dvbs2acm (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the transmission format standard applied for
the startup stream. The start transport stream carries a
Network Information Table that the RCST uses for
acquiring the forward link signaling. Supported values
are:
-1: unspecified (automatic format acquisition is
assumed)
0: DVB-S (support of this value is mandatory if
DVB-S support is claimed)
1: DVB-S2 with CCM (support of this value is
mandatory if DVB-S2 CCM support is claimed)
2: DVB-S2 with VCM or ACM (support of this value is
mandatory if DVB-S2 ACM support is claimed)
This allows the RCST to discriminate between CCM and
VCM/ACM when selecting the forward link.
The support of automatic format selection is optional.
One or several of the other format selections must be
supported, according to the claimed SatLabs profile
support."
::={dvbRcsFwdStartEntry 5}
dvbRcsFwdStartRolloff OBJECT-TYPE
SYNTAX INTEGER {
autoRolloff (0),
rolloff020 (1),
rolloff025 (2),
rolloff035 (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the receive filter roll-off applied on the
start transponder. The start transponder carries a
Network Information Table that the RCST uses for
acquiring the forward link signaling.
Supported values are:
0: any (auto)
1: 0.20
2: 0.25
3: 0.35"
::={dvbRcsFwdStartEntry 6}
dvbRcsFwdStartSymbolRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 symbols/s"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the symbol rate on the start transponder
carrying a Network Information Table to which any RCST
shall trigger to acquire forward link. Its value shall
be given in multiples of 100 symbols/s."
::={dvbRcsFwdStartEntry 7}
dvbRcsFwdStartInnerFec OBJECT-TYPE
SYNTAX INTEGER {
autoFec (-1),
fecRate12 (0),
fecRate23 (1),
fecRate34 (2),
fecRate56 (3),
fecRate78 (4),
fecRate89 (5),
fecRate35 (6),
fecRate45 (7),
fecRate910 (8),
fecRate25 (9),
fecRate13 (10),
fecRate14 (11),
noInnerCode (12)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the inner Forward Error Correction used on
the start transponder carrying a Network Information
Table to which any RCST shall trigger to acquire forward
link.
Supported values are:
autoFec (-1),
fecRate1/2 (0),
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (9),
fecRate1/3 (10),
fecRate1/4 (11),
noInnerCode (12)
The support of autoFec is optional."
::={dvbRcsFwdStartEntry 8}
dvbRcsFwdStartRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. It is not possible
to change values in a row of this table while the row is
active."
::={dvbRcsFwdStartEntry 9}
--==============================================================
-- dvbRcsFwdStatus sub-tree object types
--==============================================================
dvbRcsFwdStatusPopId OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Population identifier applied at log-on:
0-65535: specific StartPopId
If the RCST was allowed to logon with any population,
the RCST will report the base number of the announced
population ID indicated by the RCS Map Table linkage
descriptor used at logon."
::={dvbRcsFwdStatus 1}
dvbRcsFwdStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF DvbRcsFwdStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the current status of Forward Link
interfaces."
::={dvbRcsFwdStatus 2}
dvbRcsFwdStatusEntry OBJECT-TYPE
SYNTAX DvbRcsFwdStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the forward link status table. Each entry
is associated with a physical interface.
An RCST shall support at least one entry."
INDEX { dvbRcsFwdStatusIndex }
::= {dvbRcsFwdStatusTable 1}
DvbRcsFwdStatusEntry ::= SEQUENCE {
dvbRcsFwdStatusIndex Unsigned32,
dvbRcsFwdStatusIfReference Unsigned32,
dvbRcsFwdStatusNetId Unsigned32,
dvbRcsFwdStatusNetName
SnmpAdminString,
dvbRcsFwdStatusFormat INTEGER,
dvbRcsFwdStatusFrequency Unsigned32,
dvbRcsFwdStatusPolar INTEGER,
dvbRcsFwdStatusInnerFec INTEGER,
dvbRcsFwdStatusSymbolRate Unsigned32,
dvbRcsFwdStatusRolloff INTEGER,
dvbRcsFwdStatusModulation INTEGER,
dvbRcsFwdStatusFecFrame INTEGER,
dvbRcsFwdStatusPilot INTEGER,
dvbRcsFwdStatusBer Integer32,
dvbRcsFwdStatusCnr Integer32,
dvbRcsFwdStatusRxPower Integer32
}
dvbRcsFwdStatusIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the forward link status table."
::={dvbRcsFwdStatusEntry 1}
dvbRcsFwdStatusIfReference OBJECT-TYPE
SYNTAX Unsigned32 (1..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Cross reference to the interface table."
::={dvbRcsFwdStatusEntry 2}
dvbRcsFwdStatusNetId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interactive network identifier of the forward
link (from the RCS Map Table)."
::={dvbRcsFwdStatusEntry 3}
dvbRcsFwdStatusNetName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the interactive network of the forward
link (from the RCS Map Table)."
::={dvbRcsFwdStatusEntry 4}
dvbRcsFwdStatusFormat OBJECT-TYPE
SYNTAX INTEGER {
dvbs (0),
dvbs2ccm (1),
dvbs2acm (2),
reservedFormat (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the transmission format applied on the
forward link. Supported values are (from RCS Map Table):
0: DVB-S
1: DVB-S2 using CCM
2: DVB-S2 using VCM or ACM
3: reserved"
::={dvbRcsFwdStatusEntry 5}
dvbRcsFwdStatusFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 kHz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the frequency of the forward link. Its
value shall be given in multiples of 100 kHz."
::={dvbRcsFwdStatusEntry 6}
dvbRcsFwdStatusPolar OBJECT-TYPE
SYNTAX INTEGER {
linearHorizontal (0),
linearVertical (1),
circularLeft (2),
circularRight (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"2-bit field giving the polarization of the forward link
Supported values are (from RCS Map Table):
00: linear and horizontal
01: linear and vertical
10: circular left
11: circular right"
::={dvbRcsFwdStatusEntry 7}
dvbRcsFwdStatusInnerFec OBJECT-TYPE
SYNTAX INTEGER {
unknown (-1),
fecRate12 (0),
fecRate23 (1),
fecRate34 (2),
fecRate56 (3),
fecRate78 (4),
fecRate89 (5),
fecRate35 (6),
fecRate45 (7),
fecRate910 (8),
fecRate25 (9),
fecRate13 (10),
fecRate14 (11),
noInnerCode (12)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the inner Forward Error Correction used on
the forward link for transmission to the RCST.
Supported values are:
unknown (-1),
fecRate1/2 (0),
fecRate2/3 (1),
fecRate3/4 (2),
fecRate5/6 (3),
fecRate7/8 (4),
fecRate8/9 (5),
fecRate3/5 (6),
fecRate4/5 (7),
fecRate9/10 (8),
fecRate2/5 (9),
fecRate1/3 (10),
fecRate1/4 (11),
noInnerCode (12)
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
seconds. If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 8}
dvbRcsFwdStatusSymbolRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "x100 symbols/s"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the symbol rate of the forward link.
Its value shall be given in multiples of 100 symbols/s."
::={dvbRcsFwdStatusEntry 9}
dvbRcsFwdStatusRolloff OBJECT-TYPE
SYNTAX INTEGER {
undefRolloff (0),
rolloff020 (1),
rolloff025 (2),
rolloff035 (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An estimate of the roll-off applied on the forward
link.
Supported values are:
0: undefined
1: 0.20
2: 0.25
3: 0.35"
::={dvbRcsFwdStatusEntry 10}
dvbRcsFwdStatusModulation OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
mBPSK (1),
mQPSK (2),
m8PSK (3),
m16APSK (4),
m32APSK (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the modulation on the forward link used for
transmission to the RCST. Supported values are:
0: unknown
1: BPSK
2: QPSK
3: 8PSK
4: 16APSK
5: 32APSK
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
seconds.
If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 11}
dvbRcsFwdStatusFecFrame OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
shortframe (1),
longframe (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the frame length used on the forward link for
transmission to the RCST.
Supported values are:
0: Unknown
1: Short frame
2: Normal frame
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
seconds.
If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 12}
dvbRcsFwdStatusPilot OBJECT-TYPE
SYNTAX INTEGER {
unknown (0),
pilotNotused (1),
pilotUsed (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether pilots are used on the forward link
for transmission to the RCST.
Supported values are:
0: Unknown
1: Pilots are not used
2: Pilots are used
The RCST will report a value that has been used for
transmission to the RCST within the most recent 60
seconds.
If this is not relevant, the RCST will report
'unknown'."
::={dvbRcsFwdStatusEntry 13}
dvbRcsFwdStatusBer OBJECT-TYPE
SYNTAX Integer32
UNITS "exponent of 10"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the RCST BER on the Forward Link in log10
units."
::={dvbRcsFwdStatusEntry 14}
dvbRcsFwdStatusCnr OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the RCST CNR on the Forward Link in 0.1 dB
units."
::={dvbRcsFwdStatusEntry 15}
dvbRcsFwdStatusRxPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the power level of the forward link as
received at the IDU, in 0.1 dBm units."
DEFVAL { -500 }
::={dvbRcsFwdStatusEntry 16}
--==============================================================
-- dvbRcsRtnConfig sub-tree object types
--==============================================================
dvbRcsRtnConfigMaxEirp OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Max Equivalent Isotropic Radiated Power (EIRP) of the RCST,
given in resolution of 0.1 dBm and applied when the IDU
can, itself, set the necessary IDU TX output level, e.g.,
when using a BUC that has a power level detector and that
provides sufficient feedback to the IDU."
::= {dvbRcsRtnConfig 1}
dvbRcsRtnConfigDefIfLevel OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dBm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"IDU TX output level applied in case the
dvbRcsRtnConfigMaxEirp cannot be used. The resolution
is 0.1 dBm and the accuracy is +/- 1 dBm."
::= {dvbRcsRtnConfig 2}
--==============================================================
-- dvbRcsRtnStatus sub-tree object types
--==============================================================
dvbRcsRtnStatusEbN0 OBJECT-TYPE
SYNTAX Integer32
UNITS "x0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The EbN0 value reported for the return link, referenced
to the regular SYNC burst transmission, in 0.1 dB
units."
::= {dvbRcsRtnStatus 1}
dvbRcsRtnStatusSFDuration OBJECT-TYPE
SYNTAX Unsigned32 (250..7500)
UNITS "0.1 ms"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of the currently applied return link
superframe structure, in tenths of milliseconds."
::= {dvbRcsRtnStatus 2}
dvbRcsRtnStatusPayloadUnit OBJECT-TYPE
SYNTAX INTEGER {
unitATM (0),
unitMPEG (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates if the payload unit used for the return link
is ATM or MPEG."
::= {dvbRcsRtnStatus 3}
--=============================================================
-- conformance information
--=============================================================
dvbRcsRcstGroups OBJECT IDENTIFIER ::=
{dvbRcsConformance 1}
dvbRcsRcstCompliances OBJECT IDENTIFIER ::=
{dvbRcsConformance 2}
--=============================================================
-- conformance statements
--=============================================================
dvbRcsRcstCompliance1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for DVB-RCS terminals that
are compliant with SatLabs System Recommendations.
Compliance is linked to the support by the terminal of
the options or features defined in the SatLabs System
Recommendations.
The supported options and features of a terminal are
declared in objects
dvbRcsSystemSatLabsOptionsDeclaration
and dvbRcsSystemSatLabsFeaturesDeclaration
respectively."
MODULE -- this module
MANDATORY-GROUPS {dvbRcsRcstSystemGroup,
dvbRcsRcstNetworkGroup, dvbRcsRcstInstallGroup,
dvbRcsRcstQosGroup, dvbRcsRcstControlGroup,
dvbRcsRcstStateGroup, dvbRcsFwdConfigGroup,
dvbRcsFwdStatusGroup, dvbRcsRtnConfigGroup,
dvbRcsRtnStatusGroup}
GROUP dvbRcsRcstExtNetworkGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
networking management functionality. Such RCST is qualified
as supporting the EXTNETWORK feature, as defined in the
SatLabs System Recommendations."
GROUP dvbRcsRcstDnsGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the DNS
protocol. Such RCST is qualified as supporting the DNS
option, as defined in the SatLabs System Recommendations."
GROUP dvbRcsRcstExtInstallGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the
installation log file. Such RCST is qualified as supporting
the INSTALL_LOG feature, as defined in the SatLabs System
Recommendations."
GROUP dvbRcsRcstEnhancedClassifierGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
GROUP dvbRcsRcstMpegQosGroup
DESCRIPTION
"This group is mandatory for an RCST that supports MPEG
traffic bursts. Such RCST is qualified as supporting the
MPEG_TRF option, as defined in the SatLabs System
Recommendations."
GROUP dvbRcsRcstGlobalQosGroup
DESCRIPTION
"This group is mandatory for an RCST that supports global
RCST QoS configuration data. Such RCST is qualified as
supporting the RCST_PARA feature, as defined in the SatLabs
System Recommendations."
GROUP dvbRcsRcstStrictQosGroup
DESCRIPTION
"This group is mandatory for an RCST that supports strict
channel ID dispatching. Such RCST is qualified as
supporting the CHID_STRICT option, as defined in the SatLabs
System Recommendations."
GROUP dvbRcsRcstExtControlGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
control management functionality. Such RCST is qualified as
supporting the EXTCONTROL feature, as defined in the SatLabs
System Recommendations."
GROUP dvbRcsRtnExtConfigGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
return link configuration management functionality. Such
RCST is qualified as supporting the EXTCONFIG feature, as
defined in the SatLabs System Recommendations."
GROUP dvbRcsRtnExtStatusGroup
DESCRIPTION
"This group is mandatory for an RCST that supports extended
return link status report functionality. Such RCST is
qualified as supporting the EXTSTATUS feature, as defined in
the SatLabs System Recommendations."
GROUP dvbRcsRcstOduListGroup
DESCRIPTION
"This group is mandatory for an RCST that supports the ODU
structural entities defined under dvbRcsOduTx, dvbRcsOduRx,
and dvbRcsOduAntenna. Such RCST is qualified as supporting
the ODULIST feature, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsSystemOduAntennaSize
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduAntennaGain
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduSspa
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduTxType
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduRxType
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduRxBand
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduRxLO
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsSystemOduTxLO
MIN-ACCESS read-only
DESCRIPTION
"Write access must be supported if dvbRcsRcstOduListGroup is
not supported."
OBJECT dvbRcsNetworkOamInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkOamInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkLanInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkLanInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPrimaryDnsServerInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPrimaryDnsServerInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsSecondaryDnsServerInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsSecondaryDnsServerInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkNccMgtInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsNetworkNccMgtInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassDscpLow
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
OBJECT dvbRcsPktClassDscpHigh
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
OBJECT dvbRcsPktClassDscpMarkValue
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports the
enhanced classifier feature. Such RCST is qualified as
supporting the ENHCLASSIFIER feature, as defined in the
SatLabs System Recommendations."
OBJECT dvbRcsPktClassSrcInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassSrcInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassDstInetAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPktClassDstInetAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT dvbRcsPhbName
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsPhbRequestClassAssociation
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsPhbMappingRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassName
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassChanId
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassVccVpi
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassVccVci
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support. Such RCST is qualified as supporting
the SNMPMISC option, as defined in the SatLabs System
Recommendations."
OBJECT dvbRcsRequestClassPidPoolReference
MIN-ACCESS not-accessible
DESCRIPTION
"Read-only access required if the RCST supports MPEG traffic
bursts, according to the MPEG_TRF option, as defined in the
SatLabs System Recommendations. Create access only required
if the RCST also supports extended management support,
according to the SNMPMISC option, as defined in the SatLabs
System Recommendations."
OBJECT dvbRcsRequestClassCra
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassRbdcMax
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassRbdcTimeout
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassVbdcMax
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassVbdcTimeout
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassVbdcMaxBackLog
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsRequestClassRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Create access only required if the RCST supports extended
management support, according to the SNMPMISC option, as
defined in the SatLabs System Recommendations."
OBJECT dvbRcsPidValue
MIN-ACCESS not-accessible
DESCRIPTION
"Read-only access required if the RCST supports MPEG traffic
bursts, according to the MPEG_TRF option, as defined in the
SatLabs System Recommendations. Create access only required
if the RCST also supports extended management support,
according to the SNMPMISC option, as defined in the SatLabs
System Recommendations."
OBJECT dvbRcsPidPoolRowStatus
MIN-ACCESS not-accessible
DESCRIPTION
"Read-only access required if the RCST supports MPEG traffic
bursts, according to the MPEG_TRF option, as defined in the
SatLabs System Recommendations. Create access only required
if the RCST also supports extended management support,
according to the SNMPMISC option, as defined in the SatLabs
System Recommendations."
::= {dvbRcsRcstCompliances 1}
--=============================================================
-- units of conformance
--=============================================================
--=============================================================
-- object groups for RCST system
--=============================================================
dvbRcsRcstSystemGroup OBJECT-GROUP
OBJECTS {
dvbRcsSystemMibRevision,
dvbRcsSystemSatLabsProfilesDeclaration,
dvbRcsSystemSatLabsOptionsDeclaration,
dvbRcsSystemSatLabsFeaturesDeclaration,
dvbRcsSystemLocation,
dvbRcsSystemOduAntennaSize,
dvbRcsSystemOduAntennaGain,
dvbRcsSystemOduSspa,
dvbRcsSystemOduTxType,
dvbRcsSystemOduRxType,
dvbRcsSystemOduRxBand,
dvbRcsSystemOduRxLO,
dvbRcsSystemOduTxLO,
dvbRcsTcpPep,
dvbRcsHttpPep
}
STATUS current
DESCRIPTION
"A collection of objects providing information
applicable for basic device management support."
::= {dvbRcsRcstGroups 1}
--=============================================================
-- object groups for RCST networking
--=============================================================
dvbRcsRcstNetworkGroup OBJECT-GROUP
OBJECTS {
dvbRcsNetworkOamInetAddressType,
dvbRcsNetworkOamInetAddress,
dvbRcsNetworkOamInetAddressPrefixLength,
dvbRcsNetworkLanInetAddressType,
dvbRcsNetworkLanInetAddress,
dvbRcsNetworkLanInetAddressPrefixLength,
dvbRcsNetworkConfigFileDownloadUrl,
dvbRcsNetworkConfigFileUploadUrl,
dvbRcsNetworkLogFileUploadUrl
}
STATUS current
DESCRIPTION
"A collection of objects providing basic networking
management support."
::= {dvbRcsRcstGroups 2}
dvbRcsRcstExtNetworkGroup OBJECT-GROUP
OBJECTS {
dvbRcsNetworkOamInetAddressAssign,
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressType,
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddress,
dvbRcsNetworkAirInterfaceDefaultGatewayInetAddressPrefixLength,
dvbRcsNetworkNccMgtInetAddressType,
dvbRcsNetworkNccMgtInetAddress,
dvbRcsNetworkNccMgtInetAddressPrefixLength
}
STATUS current
DESCRIPTION
"A collection of objects providing extended networking
management support."
::= {dvbRcsRcstGroups 3}
dvbRcsRcstDnsGroup OBJECT-GROUP
OBJECTS {
dvbRcsPrimaryDnsServerInetAddressType,
dvbRcsPrimaryDnsServerInetAddress,
dvbRcsPrimaryDnsServerInetAddressPrefixLength,
dvbRcsSecondaryDnsServerInetAddressType,
dvbRcsSecondaryDnsServerInetAddress,
dvbRcsSecondaryDnsServerInetAddressPrefixLength
}
STATUS current
DESCRIPTION
"A collection of objects providing DNS management
support."
::= {dvbRcsRcstGroups 4}
--=============================================================
-- object groups for RCST installation
--=============================================================
dvbRcsRcstInstallGroup OBJECT-GROUP
OBJECTS {
dvbRcsInstallAntennaAlignmentState,
dvbRcsInstallCwFrequency,
dvbRcsInstallCwMaxDuration,
dvbRcsInstallCwPower,
dvbRcsInstallCoPolReading,
dvbRcsInstallXPolReading,
dvbRcsInstallCoPolTarget,
dvbRcsInstallXPolTarget,
dvbRcsInstallStandByDuration,
dvbRcsInstallTargetEsN0
}
STATUS current
DESCRIPTION
"A collection of objects providing information
applicable for basic installation support."
::= {dvbRcsRcstGroups 5}
dvbRcsRcstExtInstallGroup OBJECT-GROUP
OBJECTS {
dvbRcsNetworkInstallLogFileDownloadUrl,
dvbRcsNetworkInstallLogFileUploadUrl
}
STATUS current
DESCRIPTION
"A collection of objects providing extended device
installation support."
::= {dvbRcsRcstGroups 6}
--=============================================================
-- object groups for QoS
--=============================================================
dvbRcsRcstQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsPktClassDscpLow,
dvbRcsPktClassDscpHigh,
dvbRcsPktClassDscpMarkValue,
dvbRcsPktClassPhbAssociation,
dvbRcsPktClassRowStatus,
dvbRcsPhbName,
dvbRcsPhbRequestClassAssociation,
dvbRcsPhbMappingRowStatus,
dvbRcsRequestClassName,
dvbRcsRequestClassChanId,
dvbRcsRequestClassVccVpi,
dvbRcsRequestClassVccVci,
dvbRcsRequestClassCra,
dvbRcsRequestClassRbdcMax,
dvbRcsRequestClassRbdcTimeout,
dvbRcsRequestClassVbdcMax,
dvbRcsRequestClassVbdcTimeout,
dvbRcsRequestClassVbdcMaxBackLog,
dvbRcsRequestClassRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing basic access to QoS
configuration data."
::= {dvbRcsRcstGroups 7}
dvbRcsRcstEnhancedClassifierGroup OBJECT-GROUP
OBJECTS {
dvbRcsPktClassIpProtocol,
dvbRcsPktClassSrcInetAddressType,
dvbRcsPktClassSrcInetAddress,
dvbRcsPktClassSrcInetAddressPrefixLength,
dvbRcsPktClassDstInetAddressType,
dvbRcsPktClassDstInetAddress,
dvbRcsPktClassDstInetAddressPrefixLength,
dvbRcsPktClassSrcPortLow,
dvbRcsPktClassSrcPortHigh,
dvbRcsPktClassDstPortLow,
dvbRcsPktClassDstPortHigh,
dvbRcsPktClassVlanUserPri
}
STATUS current
DESCRIPTION
"A collection of objects providing support for
management of the enhanced classifier."
::= {dvbRcsRcstGroups 8}
dvbRcsRcstMpegQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsRequestClassPidPoolReference,
dvbRcsPidValue,
dvbRcsPidPoolRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing access to
MPEG-related link QoS configuration data."
::= {dvbRcsRcstGroups 9}
dvbRcsRcstGlobalQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsQosGlobalRbdcMax,
dvbRcsQosGlobalVbdcMax,
dvbRcsQosGlobalVbdcMaxBackLog
}
STATUS current
DESCRIPTION
"A collection of objects providing access to global RCST
QoS configuration data."
::= {dvbRcsRcstGroups 10}
dvbRcsRcstStrictQosGroup OBJECT-GROUP
OBJECTS {
dvbRcsQosChannelIdStrictDispatching
}
STATUS current
DESCRIPTION
"A collection of objects allowing management of strict
channel ID dispatching."
::= {dvbRcsRcstGroups 11}
--=============================================================
-- object groups for RCST control
--=============================================================
dvbRcsRcstControlGroup OBJECT-GROUP
OBJECTS {
dvbRcsCtrlRebootCommand,
dvbRcsCtrlUserTrafficDisable,
dvbRcsCtrlCwEnable,
dvbRcsCtrlDownloadFileCommand,
dvbRcsCtrlUploadFileCommand,
dvbRcsCtrlActivateConfigFileCommand,
dvbRcsCtrlRcstRxReacquire
}
STATUS current
DESCRIPTION
"A collection of objects allowing basic RCST control."
::= {dvbRcsRcstGroups 12}
dvbRcsRcstExtControlGroup OBJECT-GROUP
OBJECTS {
dvbRcsCtrlRcstTxDisable,
dvbRcsCtrlOduTxReferenceEnable,
dvbRcsCtrlOduTxDCEnable,
dvbRcsCtrlOduRxDCEnable,
dvbRcsCtrlRcstLogonCommand,
dvbRcsCtrlRcstLogoffCommand
}
STATUS current
DESCRIPTION
"A collection of objects allowing extended RCST
control."
::= {dvbRcsRcstGroups 13}
--=============================================================
-- object groups for RCST state
--=============================================================
dvbRcsRcstStateGroup OBJECT-GROUP
OBJECTS {
dvbRcsRcstMode,
dvbRcsRcstFaultStatus,
dvbRcsRcstFwdLinkStatus,
dvbRcsRcstLogUpdated,
dvbRcsRcstCurrentSoftwareVersion,
dvbRcsRcstAlternateSoftwareVersion,
dvbRcsRcstActivatedConfigFileVersion,
dvbRcsRcstDownloadedConfigFileVersion
}
STATUS current
DESCRIPTION
"A collection of objects allowing access to RCST state."
::= {dvbRcsRcstGroups 14}
--=============================================================
-- object groups for forward link
--=============================================================
dvbRcsFwdConfigGroup OBJECT-GROUP
OBJECTS {
dvbRcsFwdStartPopId,
dvbRcsFwdStartFrequency,
dvbRcsFwdStartPolar,
dvbRcsFwdStartFormat,
dvbRcsFwdStartRolloff,
dvbRcsFwdStartSymbolRate,
dvbRcsFwdStartInnerFec,
dvbRcsFwdStartRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing basic start forward
link configuration support."
::= {dvbRcsRcstGroups 15}
dvbRcsFwdStatusGroup OBJECT-GROUP
OBJECTS {
dvbRcsFwdStatusPopId,
dvbRcsFwdStatusIfReference,
dvbRcsFwdStatusNetId,
dvbRcsFwdStatusNetName,
dvbRcsFwdStatusFormat,
dvbRcsFwdStatusFrequency,
dvbRcsFwdStatusPolar,
dvbRcsFwdStatusInnerFec,
dvbRcsFwdStatusSymbolRate,
dvbRcsFwdStatusRolloff,
dvbRcsFwdStatusModulation,
dvbRcsFwdStatusFecFrame,
dvbRcsFwdStatusPilot,
dvbRcsFwdStatusBer,
dvbRcsFwdStatusCnr,
dvbRcsFwdStatusRxPower
}
STATUS current
DESCRIPTION
"A collection of objects providing forward link status."
::= {dvbRcsRcstGroups 16}
--=============================================================
-- object groups for return link
--=============================================================
dvbRcsRtnConfigGroup OBJECT-GROUP
OBJECTS {
dvbRcsRtnConfigDefIfLevel
}
STATUS current
DESCRIPTION
"A collection of objects providing basic return link
configuration support."
::= {dvbRcsRcstGroups 17}
dvbRcsRtnExtConfigGroup OBJECT-GROUP
OBJECTS {
dvbRcsRtnConfigMaxEirp
}
STATUS current
DESCRIPTION
"A collection of objects providing extended return link
configuration support."
::= {dvbRcsRcstGroups 18}
dvbRcsRtnStatusGroup OBJECT-GROUP
OBJECTS {
dvbRcsRtnStatusPayloadUnit
}
STATUS current
DESCRIPTION
"A collection of objects allowing access to return link
status."
::= {dvbRcsRcstGroups 19}
dvbRcsRtnExtStatusGroup OBJECT-GROUP
OBJECTS {
dvbRcsRcstRtnLinkStatus,
dvbRcsRtnStatusEbN0,
dvbRcsRtnStatusSFDuration
}
STATUS current
DESCRIPTION
"A collection of objects allowing access to extended
return link status."
::= {dvbRcsRcstGroups 20}
dvbRcsRcstOduListGroup OBJECT-GROUP
OBJECTS {
dvbRcsOduTxTypeDescription,
dvbRcsOduTxType,
dvbRcsOduRxTypeDescription,
dvbRcsOduRxType,
dvbRcsOduAntennaTypeDescription,
dvbRcsOduAntennaType
}
STATUS current
DESCRIPTION
"A collection of objects supporting flexible
selection of ODU devices."
::= {dvbRcsRcstGroups 21}
END
View Git Blame Copy Permalink