634 lines
19 KiB
Plaintext

-- *****************************************************************
-- FS-RIP-MIB.mib: FS RIP MIB file
--
-- March 2002, Wuzg
--
-- Copyright (c) 2002 by FS.COM Inc..
-- All rights reserved.
--
-- *****************************************************************
--
FS-RIP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
TimeTicks,
Unsigned32,
Integer32,
Counter32,
IpAddress
FROM SNMPv2-SMI
DisplayString,
RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF
IfIndex
FROM FS-TC
EnabledStatus
FROM P-BRIDGE-MIB
fsMgmt
FROM FS-SMI;
fsRIPMIB MODULE-IDENTITY
LAST-UPDATED "200203200000Z"
ORGANIZATION "FS.COM Inc.."
CONTACT-INFO
"
Tel: 400-865-2852
E-mail: https://www.fs.com/live_chat_service_mail.html"
DESCRIPTION
"This module defines fs Rip mibs."
REVISION "200203200000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { fsMgmt 13}
fsRIPMIBObjects OBJECT IDENTIFIER ::= { fsRIPMIB 1 }
---
---RIP GROUP
---
fsRipEnable OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Rip management function status"
DEFVAL { disabled }
::={ fsRIPMIBObjects 1 }
fsRipUpdateTime OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The rate (time in seconds between updates) at which routing updates are sent."
DEFVAL {30}
::={ fsRIPMIBObjects 2 }
fsRipInvalidTime OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The interval of time (in seconds) after which a route is declared invalid."
DEFVAL {180}
::={ fsRIPMIBObjects 3 }
fsRipHolddownTime OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The amount of time (in seconds) that must pass before a route
is removed from the routing table"
DEFVAL {120}
::={ fsRIPMIBObjects 4 }
fsRipRecommendSetting OBJECT-TYPE
SYNTAX INTEGER{
ripv1(1),
ripv2(2),
compatible(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"User can set this object to 1,2,3.
1 means that the system sending and receiving RIP version1 packets,
2 means that the system sending and receiving RIP version2 packets,
3 means that the system sending RIP version1 packets and receiving both
RIP version1 and RIP version2 packets.
If the system RIP interface configuration has been modified by user,this
object will be 4."
DEFVAL {3}
::={fsRIPMIBObjects 5}
-- The RIP Interface Status Table.
fsRipIfStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSRipIfStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of subnets which require separate
status monitoring in RIP."
::= { fsRIPMIBObjects 6 }
fsRipIfStatEntry OBJECT-TYPE
SYNTAX FSRipIfStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Single Routing Domain in a single Subnet."
INDEX { fsRipIfStatIfIndex }
::= { fsRipIfStatTable 1 }
FSRipIfStatEntry ::=
SEQUENCE {
fsRipIfStatIfIndex
IfIndex,
fsRipIfStatRcvBadPackets
Counter32,
fsRipIfStatRcvBadRoutes
Counter32,
fsRipIfStatSentUpdates
Counter32
}
fsRipIfStatIfIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"VID of vlan which each net interface associate."
::= { fsRipIfStatEntry 1 }
fsRipIfStatRcvBadPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of RIP response packets received by
the RIP process which were subsequently discarded
for any reason (e.g. a version 0 packet, or an
unknown command type)."
::= { fsRipIfStatEntry 2 }
fsRipIfStatRcvBadRoutes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of routes, in valid RIP packets,
which were ignored for any reason (e.g. unknown
address family, or invalid metric)."
::= { fsRipIfStatEntry 3 }
fsRipIfStatSentUpdates OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of triggered RIP updates actually
sent on this interface. This explicitly does
NOT include full updates sent containing new
information."
::= { fsRipIfStatEntry 4 }
-- The RIP Interface Configuration Table.
fsRipIfConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSRipIfConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of interfaces which require separate
configuration in RIP."
::= { fsRIPMIBObjects 7 }
fsRipIfConfEntry OBJECT-TYPE
SYNTAX FSRipIfConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A Single Routing Domain in a single interface."
INDEX { fsRipIfConfIfIndex }
::= { fsRipIfConfTable 1 }
FSRipIfConfEntry ::=
SEQUENCE {
fsRipIfConfIfIndex
IfIndex,
fsRipIfConfAuthType
INTEGER,
fsRipIfConfAuthKeyChain
DisplayString,
fsRipIfConfSend
INTEGER,
fsRipIfConfReceive
INTEGER,
fsRipIfPassiveStatus
EnabledStatus,
fsRipIfBroadcastEnable
EnabledStatus,
fsRipIfAdminStat
EnabledStatus
}
fsRipIfConfIfIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"IfIndex vale of vlan interface."
::= { fsRipIfConfEntry 1 }
fsRipIfConfAuthType OBJECT-TYPE
SYNTAX INTEGER {
noAuthentication(1),
simplePassword (2),
md5(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of Authentication used on this
interface."
DEFVAL { noAuthentication }
::= { fsRipIfConfEntry 2 }
fsRipIfConfAuthKeyChain OBJECT-TYPE
SYNTAX DisplayString(SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The key chain name which interface associated. It indicate that
this interface doesn't match any key chain which this string is null"
REFERENCE
"fsAuthenKeyChainName in FS-AUTHEN-KEY-MIB."
::= { fsRipIfConfEntry 3 }
fsRipIfConfSend OBJECT-TYPE
SYNTAX INTEGER {
ripVersion1 (1),
rip1Compatible (2),
ripVersion2 (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"What the router sends on this interface.
ripVersion1 implies sending RIP updates compliant
with RFC 1058. rip1Compatible implies
broadcasting RIP-2 updates using RFC 1058 route
subsumption rules. ripVersion2 implies
multicasting RIP-2 updates. ripV1Demand indicates
the use of Demand RIP on a WAN interface under RIP
Version 1 rules. ripV2Demand indicates the use of
Demand RIP on a WAN interface under Version 2 rules."
DEFVAL { rip1Compatible }
::= { fsRipIfConfEntry 4 }
fsRipIfConfReceive OBJECT-TYPE
SYNTAX INTEGER {
rip1 (1),
rip2 (2),
rip1OrRip2 (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This indicates which version of RIP updates
are to be accepted. Note that rip2 and
rip1OrRip2 implies reception of multicast
packets."
DEFVAL { rip1OrRip2 }
::= { fsRipIfConfEntry 5 }
fsRipIfPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
" The interface will not send routing updates if this value is 'enabled'"
DEFVAL { disabled }
::={ fsRipIfConfEntry 6 }
fsRipIfBroadcastEnable OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable or disable broadcast updats of RIP in this interface"
DEFVAL { disabled }
::={ fsRipIfConfEntry 7 }
fsRipIfAdminStat OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The RIP interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to RIP."
::= { fsRipIfConfEntry 8 }
fsRipOffsetMetric OBJECT-TYPE
SYNTAX Integer32 (1..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object means the value of increasing incoming
and outgoing metrics to routes learned via RIP "
DEFVAL {1}
::={ fsRIPMIBObjects 8 }
fsRipAdministrativeDistance OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specified the priority of route information learned via RIP."
::={ fsRIPMIBObjects 9}
fsRipValidateUpdateSrcEnable OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object allow of enabling or disabling validate the
source IP address of incoming RIP routing updates."
DEFVAL { enabled }
::={ fsRIPMIBObjects 10 }
fsRipPassiveStatus OBJECT-TYPE
SYNTAX EnabledStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The fsRipIfPassiveStatus of a interface equal to this object value
when this interface is created. If you change this object value to 'enabled'
or 'disabled'all interfaces which have exist will also change their
fsRipIfPassiveStatus to 'enabled' or 'disabled'."
DEFVAL { disabled }
::={ fsRIPMIBObjects 11 }
fsRipNextDueIn OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Waitting time interval before next update packet generatting
in units of second"
::={ fsRIPMIBObjects 12 }
-- The RIP Interface Offset Table.
fsRipIfOffsetTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSRipIfOffsetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interface configuration about offset.
Apply an offset list to routing metrics to increase incoming and
outgoing metrics to routes learned through RIP. You can limit
the offset list with an access list or an interface."
::= { fsRIPMIBObjects 13 }
fsRipIfOffsetEntry OBJECT-TYPE
SYNTAX FSRipIfOffsetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX { fsRipIfOffsetIfIndex,fsRipIfOffsetMethod }
::= { fsRipIfOffsetTable 1 }
FSRipIfOffsetEntry ::=
SEQUENCE {
fsRipIfOffsetIfIndex
Integer32,
fsRipIfOffsetMethod
INTEGER,
fsRipIfOffsetAclName
DisplayString,
fsRipIfOffsetMetric
Unsigned32,
fsRipIfOffsetStatus
RowStatus
}
fsRipIfOffsetIfIndex OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the interface that this offset list apply to.
If this value is 0,it indicate that this offset list apply in all
interfaces except the interfaceswhich which have not Offset configure.
Other value is equal to TEXTUAL-CONVENTION IfIndex meaning,this offset
list will apply in only the designate interface"
::= { fsRipIfOffsetEntry 1 }
fsRipIfOffsetMethod OBJECT-TYPE
SYNTAX INTEGER{
out(1),
in(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"the offset list apply to incoming routes or
outgoing routes."
::= { fsRipIfOffsetEntry 2 }
fsRipIfOffsetAclName OBJECT-TYPE
SYNTAX DisplayString(SIZE(1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" the offset list with Access list name ."
::= { fsRipIfOffsetEntry 3 }
fsRipIfOffsetMetric OBJECT-TYPE
SYNTAX Unsigned32(0..16)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"the offset list with offset value,
in condition the value will be added to route metric."
::= { fsRipIfOffsetEntry 4 }
fsRipIfOffsetStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" if this value is setted destroy,
the entry will be deleted ."
::= { fsRipIfOffsetEntry 5 }
--network table
fsRipNetworkTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSRipNetworkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the network for rip routing."
::= { fsRIPMIBObjects 14 }
fsRipNetworkEntry OBJECT-TYPE
SYNTAX FSRipNetworkEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX { fsRipNetworkAddr }
::= { fsRipNetworkTable 1 }
FSRipNetworkEntry ::=
SEQUENCE {
fsRipNetworkAddr
IpAddress,
fsRipNetworkMask
IpAddress,
fsRipNetworkStatus
RowStatus
}
fsRipNetworkAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"define a network for rip routing ."
::= { fsRipNetworkEntry 1 }
fsRipNetworkMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"define a network's mask for rip routing ."
::= { fsRipNetworkEntry 2 }
fsRipNetworkStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"if destroy is setted,
this entry will be deleted ."
::= { fsRipNetworkEntry 3 }
--neighbor table
fsRipNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSRipNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the neighbor for rip routing."
::= { fsRIPMIBObjects 15 }
fsRipNeighborEntry OBJECT-TYPE
SYNTAX FSRipNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"the entry of this table."
INDEX { fsRipNeighborIndex }
::= { fsRipNeighborTable 1 }
FSRipNeighborEntry ::=
SEQUENCE {
fsRipNeighborIndex
IpAddress,
fsRipNeighborStatus
RowStatus
}
fsRipNeighborIndex OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"define a neighbor for rip ."
::= { fsRipNeighborEntry 1 }
fsRipNeighborStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"if destroy is setted,
this entry will be deleted."
::= { fsRipNeighborEntry 2 }
fsRIPMIBConformance OBJECT IDENTIFIER ::= { fsRIPMIB 2 }
fsRIPMIBCompliances OBJECT IDENTIFIER ::= { fsRIPMIBConformance 1 }
fsRIPMIBGroups OBJECT IDENTIFIER ::= { fsRIPMIBConformance 2 }
-- compliance statements
fsRIPMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which implement
the FS Snooping Dhcp MIB"
MODULE -- this module
MANDATORY-GROUPS { fsRipMIBGroup,
fsRIPExtendMIBGroup
}
::= { fsRIPMIBCompliances 1 }
-- units of conformance
fsRipMIBGroup OBJECT-GROUP
OBJECTS {
fsRipEnable,
fsRipUpdateTime,
fsRipInvalidTime,
fsRipHolddownTime,
fsRipRecommendSetting,
fsRipIfStatIfIndex,
fsRipIfStatRcvBadPackets,
fsRipIfStatRcvBadRoutes,
fsRipIfStatSentUpdates,
fsRipIfConfIfIndex,
fsRipIfConfAuthType,
fsRipIfConfAuthKeyChain,
fsRipIfConfSend,
fsRipIfConfReceive,
fsRipIfPassiveStatus,
fsRipIfBroadcastEnable,
fsRipIfAdminStat,
fsRipOffsetMetric,
fsRipAdministrativeDistance,
fsRipValidateUpdateSrcEnable
}
STATUS current
DESCRIPTION
"A collection of objects providing rip managment."
::= { fsRIPMIBGroups 1 }
fsRIPExtendMIBGroup OBJECT-GROUP
OBJECTS {
fsRipNextDueIn,
fsRipIfOffsetIfIndex,
fsRipIfOffsetMethod,
fsRipIfOffsetAclName,
fsRipIfOffsetMetric,
fsRipIfOffsetStatus,
fsRipNetworkAddr,
fsRipNetworkMask,
fsRipNetworkStatus,
fsRipNeighborIndex,
fsRipNeighborStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing rip extend managment."
::= { fsRIPMIBGroups 2 }
END