WebApps/Observium_CE
1
0
Fork 0
Code Pull Requests Activity
Observium_CE/mibs/cisco/CISCO-LWAPP-QOS-MIB

5467 lines
199 KiB
Plaintext
Raw Permalink Blame History

-- *******************************************************************
-- CISCO-LWAPP-QOS-MIB.my
-- November 2005, Devesh Pujari, Bharat Biswal,
-- Prasanna Viswakumar, Srinath Candadai
--
-- Copyright (c) 2005-2018 by Cisco Systems Inc.
-- All rights reserved.
-- *******************************************************************
CISCO-LWAPP-QOS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Unsigned32,
Counter32,
Gauge32
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
RowStatus,
TruthValue,
TimeStamp,
TEXTUAL-CONVENTION
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
InetAddressType,
InetAddress
FROM INET-ADDRESS-MIB
TimeIntervalSec
FROM CISCO-TC
cldcClientMacAddress
FROM CISCO-LWAPP-DOT11-CLIENT-MIB
cLApSysMacAddress,
cLApDot11IfSlotId,
cLApName,
cLApDot11IfType,
cLApDot11IfEntry
FROM CISCO-LWAPP-AP-MIB
cLWlanIndex,
cLAPGroupName,
cLWlanConfigEntry,
cLWlanProfileName
FROM CISCO-LWAPP-WLAN-MIB
ciscoMgmt
FROM CISCO-SMI;
-- ********************************************************************
-- * MODULE IDENTITY
-- ********************************************************************
ciscoLwappQosMIB MODULE-IDENTITY
LAST-UPDATED "201804240000Z"
ORGANIZATION "Cisco Systems Inc."
CONTACT-INFO
"Cisco Systems,
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
Email: cs-wnbu-snmp@cisco.com"
DESCRIPTION
"This MIB is intended to be implemented on all those
devices operating as Central controllers, that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
Information provided by this MIB is used to study
the quality of service in the voice and video traffic
on the WLAN.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+
+ + + + + +
+ CC + + CC + + CC +
+ + + + + +
+......+ +......+ +......+
.. . .
.. . .
. . . .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ AP + + AP + + AP + + AP +
+ + + + + + + +
+......+ +......+ +......+ +......+
. . .
. . . .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ MN + + MN + + MN + + MN +
+ + + + + + + +
+......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Gratuitous Probe Response (GPR)
The Gratuitous Probe Response feature aids in conserving
battery power of WLAN-enabled cell phones by providing
a high rate packet on the order of tens of milliseconds
such that these kind of phones can wake up and wait at
predefined intervals, to reduce battery power. The
GPR packet is transmitted from the AP at a predefined
time interval.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node
and client are used interchangeably.
TU
A measurement of time in units of 1024 microseconds.
User Priority ( UP )
Specifies a the priority rules in QOS for handling user
priority.
EDCA
As defined in 802.11e standard, Enhanced distributed
channel access(EDCA) parameter set element is used
by the AP to establish policy, to change policy when
accepting new clients, or to adapt to changes in
offered load.
KTS (Key Telephone System)
Key Telephone System is an alternative to a private branch
exchange (PBX) phone system. A KTS is equipped with several
buttons that allow a caller to directly select outgoing lines or
incoming calls, and use intercom and conference facilities.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol"
REVISION "201804240000Z"
DESCRIPTION
"Added the following objects to the table cLQoSProfileTable
cLQoSWlanDSAverageDataRate
cLQoSWlanUSAverageDataRat
cLQoSWlanDSBurstDataRate
cLQoSWlanUSBurstDataRate
cLQoSWlanDSAvgRealTimeDataRate
cLQoSWlanUSAvgRealTimeDataRate
cLQoSWlanDSBurstRealTimeDataRate
cLQoSWlanUSBurstRealTimeDataRate
Deprecated ciscoLwappQosMIBComplianceRev3 and
replaced it with ciscoLwappQosMIBComplianceRev4."
REVISION "201705120000Z"
DESCRIPTION
"Added the following groups:
ciscoLwappQosMIBComplianceRev2,
ciscoLwappQosDot11aConfigGroupSup2,
ciscoLwappQosDot11bConfigGroupSup2,
ciscoLwappQosDot11SipCacStatsGroup,
ciscoLwappQosDot11SipConfigGroup,
ciscoLwappQosDot11VoiceStatsGroup,
ciscoLwappQosDot11VoiceConfigGroup,
ciscoLwappQosConfigGroup,
ciscoLwappQosDot11VoiceNotifGroup
Deprecated ciscoLwappQosMIBComplianceRev1 and
replaced it with ciscoLwappQosMIBComplianceRev2."
REVISION "200701070000Z"
DESCRIPTION
"Added ciscoLwappQosDot11aConfigGroupSup1 and
ciscoLwappQosDot11bConfigGroupSup1 objects."
REVISION "200604130000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { ciscoMgmt 524 }
ciscoLwappQosMIBNotifs OBJECT IDENTIFIER
::= { ciscoLwappQosMIB 0 }
ciscoLwappQosMIBObjects OBJECT IDENTIFIER
::= { ciscoLwappQosMIB 1 }
ciscoLwappQosMIBConform OBJECT IDENTIFIER
::= { ciscoLwappQosMIB 2 }
cLQd11aCACConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 1 }
cLQd11bCACConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 2 }
cLQd11GprConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 3 }
cLQd11CACStats OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 4 }
cLQEntConfConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 5 }
cLQd11VoiceStats OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 6 }
cLQVoiceWlanConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 7 }
cLQVoiceClient OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 8 }
cLQd11SipCacConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 9 }
cLQConfigObjects OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 10 }
cLQMediaClient OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 11 }
cLQMediaStreamConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 12 }
cLQPreferredCallConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 13 }
cLQoSProfileConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 14 }
cLQoSSipSnoopingConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 15 }
cLQoSAirTimeFairness OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 16 }
cLQoSMapConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 17 }
cLQoSFastlaneConfig OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 18 }
ciscoLwappQosMIBTableObjects OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 19 }
ciscoLwappQosMIBGlobalObjects OBJECT IDENTIFIER
::= { ciscoLwappQosMIBObjects 20 }
CiscoLwappDot11aPhyRates ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This object indicates the physical rates supported by a
802.11a radio.
The different physical rates (in Mbps) are 6,9,
12, 18, 24, 36, 48, 54.
11n rates: 65,72.2, 130, 135, 144.4, 150, 270, 300."
SYNTAX INTEGER {
six(6),
nine(9),
twelve(12),
eighteen(18),
twentyfour(24),
thirtysix(36),
fortyeight(48),
fiftyfour(54),
sixtyfive(65),
seventyTwoPointTwo(72),
oneThirty(130),
oneThirtyfive(135),
oneFortyFourPointFour(144),
oneFifty(150),
twoSeventy(270),
threeHundred(300)
}
CiscoLwappDot11bPhyRates ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This object indicates the physical rates supported by a
802.11b radio.
The different physical rates (in Mbps) are 1, 2,
5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54.
11n rates: 65,72.2, 130, 135, 144.4, 150, 270, 300."
SYNTAX INTEGER {
one(1),
two(2),
fivepointfive(5),
six(6),
nine(9),
eleven(11),
twelve(12),
eighteen(18),
twentyfour(24),
thirtysix(36),
fortyeight(48),
fiftyfour(54),
sixtyfive(65),
seventyTwoPointTwo(72),
oneThirty(130),
oneThirtyfive(135),
oneFortyFourPointFour(144),
oneFifty(150),
twoSeventy(270),
threeHundred(300)
}
-- ********************************************************************
-- * Configuration for Call Admission Control parameters
-- * for VOICE traffic in 802.11a interfaces in the controller
-- ********************************************************************
cLQd11aVoiceAdmCtrlSupport OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies admission control for voice traffic
flowing through the 802.11a interfaces in the controller.
A value of 'true' indicates that, controller will reserve
and manage max-bandwidth (cLQd11aVoiceMaxAdmBandwidth)
and roaming-bandwidth (cLQd11aVoiceMaxRoamBandwidth) as per
user configured values.
A value of 'false' indicates that, admission control will
not be enforced.This may delay voice traffic depending on
load on the WLAN."
DEFVAL { true }
::= { cLQd11aCACConfig 1 }
cLQd11aVoiceMaxAdmBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum bandwidth
that can be allocated by controller for voice
traffic when admission control is enabled for
for 802.11a interfaces in the controller.
Please note that the write operation on this
object will be successful only if the 802.11a
network is not operational and the total
value populated for this object for all the
admission control attributes (voice, video)
together does not exceed 100%."
DEFVAL { 75 }
::= { cLQd11aCACConfig 2 }
cLQd11aVoiceMaxRoamBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the bandwidth relative
to the maximum allocated bandwidth indicated by
cLQd11aVoiceMaxAdmBandwidth, that can be
allocated to roaming clients for voice traffic,
when admission control is enabled for 802.11a
interfaces in the controller.
Please note that the write operation on this
object will be successful only if the 802.11a
network is disabled and not operational. The
value configured through this object takes
effect when the 802.11a network is enabled."
DEFVAL { 0 }
::= { cLQd11aCACConfig 3 }
-- ********************************************************************
-- * Configuration for Call Admission Control parameters
-- * for VIDEO traffic in 802.11a interfaces in the controller
-- ********************************************************************
cLQd11aVideoAdmCtrlSupport OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether admission
control for video traffic flowing through the 802.11a
interfaces in the controller should be enabled or disabled.
A value of 'true' indicates that, controller will reserve
and manage max-bandwidth (cLQd11aVideoMaxAdmBandwidth)
and roaming-bandwidth (cLQd11aVideoMaxRoamBandwidth) as per
user configured values.
A value of 'false' indicates that admission control will
not be enforced.This may delay video traffic depending on
load on the WLAN."
DEFVAL { false }
::= { cLQd11aCACConfig 4 }
cLQd11aVideoMaxAdmBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum bandwidth
that can be allocated by controller for video traffic
when admission control is enabled for 802.11a
interfaces in the controller. When set to 0, all
available bandwidth in 802.11a interfaces can be
allocated to video traffic.
Please note that the write operation on this
object will be successful only if the 802.11a
network is not operational and the total
value populated for this object for all the
admission control attributes (voice, video)
together does not exceed 100%."
DEFVAL { 0 }
::= { cLQd11aCACConfig 5 }
cLQd11aVideoMaxRoamBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the bandwidth relative
to the maximum allocated bandwidth indicated by
cLQd11aVideoMaxAdmBandwidth, that can be
allocated to roaming clients for video traffic,
when admission control is enabled for 802.11a
interfaces in the controller.
Please note that the write operation on this
object will be successful only if the 802.11a
network is disabled and not operational. The
value configured through this object takes effect
when the 802.11a network is enabled and
operational."
DEFVAL { 0 }
::= { cLQd11aCACConfig 6 }
-- ********************************************************************
-- * Configuration of GPR (Gratuitous Probe Response) probe interval
-- * for all 802.11a interfaces in the controller
-- ********************************************************************
cLQd11aGprProbeInterval OBJECT-TYPE
SYNTAX Unsigned32 (10..100)
UNITS "TU"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the GPR probe interval
period to be used by all 802.11a interfaces in the
controller, when the radios are advertising any
WLAN with GPR support enabled.
Please note that the write operation on this
object will be successful only if the 802.11a
network is not operational. The value configured
through this object takes effect when the 802.11a
network is enabled and operational."
DEFVAL { 10 }
::= { cLQd11aCACConfig 7 }
cLQd11aVoiceCtrl OBJECT-TYPE
SYNTAX INTEGER {
loadBased(1),
static(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the parameters that can be modified
when admission control is enabled.
loadBased - Controller will reserve and manage
max-bandwidth and roaming-bandwidth
based on the load on the WLAN.
static - Controller will reserve and manage
max-bandwidth(cLQd11aVoiceMaxAdmBandwidth)
and roaming-bandwidth
(cLQd11aVoiceMaxRoamBandwidth) as per user
configured values.
When ACM is disabled, admission control will not
be enforced. This may delay voice traffic depending
on the traffic on the WLAN."
DEFVAL { loadBased }
::= { cLQd11aCACConfig 8 }
cLQd11aExpeditedBw OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies if expedited BW feature is
enabled or not.
A value of 'true' indicates that the APs advertise
the expedited BW support in their beacons and
association responses.
A value of 'false' indicates that the APs do not
advertise the expedited BW support in their beacons
and association responses."
::= { cLQd11aCACConfig 9 }
cLQd11aEdcaProfile OBJECT-TYPE
SYNTAX INTEGER {
wmmDefault(1),
svpVoice(2),
optimizedVoice(3),
optimizedVideoVoice(4),
customVoice(5),
fastlane(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the EDCA profile to be used
in EDCA Parameter set element.
wmmDefault(1) - WMM default standard parameters.
svpVoice(2) - Spectralink voice priority parameters.
optimizedVoice(3) - parameters for voice optimization.
optimizedVideoVoice(4) - parameters for video and voice
optimization.
customVoice(5) - parameters for customized voice.
fastlane(6) - parameters for fast lane."
::= { cLQd11aCACConfig 10 }
cLQd11aMacOptimization OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies MAC enhancements for voice,
resulting in improvement in number of voice calls
serviced per access point.
A value of 'true' indicates that MAC optimization will be
enabled.
A value of 'false' indicates that MAC optimization will be
disabled."
DEFVAL { false }
::= { cLQd11aCACConfig 11 }
cLQd11aMaxCallLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies the max number of CAC voice calls
allowed on dot11a radio band. Value of zero denotes no
limit."
::= { cLQd11aCACConfig 12 }
-- ********************************************************************
-- * Configuration for Call Admission Control parameters
-- * for mc2uc in 802.11a interfaces in the controller
-- ********************************************************************
cLQd11aMcastDirectEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the decision flag to allow multicast
direct stream on dot11a radio.
A value of 'true' indicates that multicast direct stream
on dot11a radio has to be allowed.
A value of 'false' indicates that multicast direct stream
on dot11a radio has to be disabled."
DEFVAL { true }
::= { cLQd11aCACConfig 13 }
cLQd11aBestEffortAdmission OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether to admit a media stream in
best effort queue.
A value of 'true' indicates that it admits a media stream
in best effort queue.
A value of 'false' indicates that it does not admit
media stream in best effort queue."
DEFVAL { false }
::= { cLQd11aCACConfig 14 }
cLQd11aRedirectBestEffort OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether a unicast or multicast only
video stream can be redirected to best effort.
A value of 'true' indicates that unicast or multicast
only video stream can be redirected to best effort.
A value of 'false' indicates that unicast or multicast
only video stream cannot be redirected to best effort."
DEFVAL { true }
::= { cLQd11aCACConfig 15 }
cLQd11aRadioMaxStreams OBJECT-TYPE
SYNTAX INTEGER (0..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum number of allowed
streams per radio for a 802.11a band."
DEFVAL { 0 }
::= { cLQd11aCACConfig 16 }
cLQd11aMaxVideoATPercent OBJECT-TYPE
SYNTAX INTEGER (0..85)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum allowed bandwidth
for video traffic."
::= { cLQd11aCACConfig 17 }
cLQd11aMaxVoiceATPercent OBJECT-TYPE
SYNTAX INTEGER (0..85)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum allowed bandwidth for
voice traffic."
::= { cLQd11aCACConfig 18 }
cLQd11aMaxMediaATPercent OBJECT-TYPE
SYNTAX INTEGER (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum allowed bandwidth for
media traffic."
::= { cLQd11aCACConfig 19 }
cLQd11aMinPhyRate OBJECT-TYPE
SYNTAX CiscoLwappDot11aPhyRates
UNITS "Mbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the minimum rate client needs to have
in order to join media stream."
DEFVAL { 1 }
::= { cLQd11aCACConfig 20 }
cLQd11aClientMaxStreams OBJECT-TYPE
SYNTAX INTEGER (0..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum number of allowed
streams per client for a 802.11a band."
DEFVAL { 0 }
::= { cLQd11aCACConfig 21 }
cLQd11aSipCacSupportEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether SIP CAC is supported on dot11a radio
band or not.
A value of 'true' indicates that SIP CAC support on dot11a
radio band will be enabled.
A value of 'false' indicates that SIP CAC support on dot11a
radio band will be disabled."
DEFVAL { false }
::= { cLQd11aCACConfig 22 }
cLQd11aMaxRetryPercent OBJECT-TYPE
SYNTAX INTEGER (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum retry percentage for
media traffic on dot11a radio band."
::= { cLQd11aCACConfig 23 }
-- ******************************************************************
-- Configuration of Video CAC Method
-- ******************************************************************
cLQd11aVideoCtrl OBJECT-TYPE
SYNTAX INTEGER {
loadBased(1),
static(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Admission Control Method(ACM)
used on dot11a radio band. When admission control is
enabled these parameters can be modified.
loadBased(1) - Controller will reserve and manage
max-bandwidth and roaming-bandwidth
based on the load on the WLAN.
static(2) - Controller will reserve and
manage max-bandwidth
(cLQd11aVideoMaxAdmBandwidth) and
roaming-bandwidth
(cLQd11aVideoMaxRoamBandwidth) as per user
configured values.
When ACM is disabled, admission control will not
be enforced. This may delay video traffic depending
on the traffic on the WLAN."
DEFVAL { loadBased }
::= { cLQd11aCACConfig 24 }
-- ******************************************************************
-- Configuration of SIP based Video-CAC method
-- ******************************************************************
cLQd11aSipCacVideoEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether SIP based video CAC is
enabled on dot11a radio band or not.
A value of 'true' indicates that SIP based video CAC on
dot11a radio band will be enabled.
A value of 'false' indicates that SIP based video CAC on
dot11a radio band will be disabled."
DEFVAL { false }
::= { cLQd11aCACConfig 25 }
-- ********************************************************************
-- * Configuration for Call Admission Control parameters
-- * for VOICE traffic in 802.11b/g interfaces in the controller
-- ********************************************************************
cLQd11bVoiceAdmCtrlSupport OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the status of admission
control for voice traffic flowing through the
802.11b/g interfaces in the controller.
A value of 'true' indicates that controller will reserve
and manage max-bandwidth (cLQd11bVoiceMaxAdmBandwidth)
and roaming-bandwidth
(cLQd11bVoiceMaxRoamingBandwidth) as per user
configured values.
A value of 'false' indicates that admission control will
not be enforced.This may delay voice traffic depending on
load on the WLAN."
DEFVAL { true }
::= { cLQd11bCACConfig 1 }
cLQd11bVoiceMaxAdmBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum bandwidth that
can be allocated by controller for voice traffic
when admission control is enabled for 802.11b/g
interfaces on the controller.
Please note that, write operation on this
object will be successful only if the 802.11b/g
network is not operational and the total
value populated for this object for all the
admission control attributes (voice, video)
together does not exceed 100%."
::= { cLQd11bCACConfig 2 }
cLQd11bVoiceMaxRoamBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the bandwidth relative
to the maximum allocated bandwidth(indicated by
cLQd11bVoiceMaxAdmBandwidth) that can be
allocated to roaming clients for voice traffic,
when admission control is enabled for 802.11b
interfaces in the controller.
Please note that, write operation on this
object will be successful only if the 802.11b/g
network is not operational. The value configured
through this object takes effect when the 802.11b/g
network is enabled and operational."
DEFVAL { 0 }
::= { cLQd11bCACConfig 3 }
-- ********************************************************************
-- * Configuration for Call Admission Control parameters
-- * for VIDEO traffic in 802.11b/g interfaces in the controller
-- ********************************************************************
cLQd11bVideoAdmCtrlSupport OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the status of admission
control for video traffic flowing through the
802.11b/g interfaces in the controller.
A value of 'true' indicates that controller will reserve
and manage max-bandwidth (cLQd11bVideoMaxAdmBandwidth)
and roaming-bandwidth
(cLQd11bVideoMaxRoamBandwidth) as per user
configured values.
A value of 'false' indicates that admission control will
not be enforced. This may delay video traffic depending on
load on the WLAN."
DEFVAL { true }
::= { cLQd11bCACConfig 4 }
cLQd11bVideoMaxAdmBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum bandwidth that
can be allocated by controller for video traffic when
admission control is enabled for 802.11b/g interfaces
in the controller. When set to 0, all available
bandwidth in 802.11b/g interfaces can be allocated
to video traffic.
Please note that the write operation on this
object will be successful only if the 802.11b/g
network is not operational and the total
value populated for this object for all the
admission control attributes (voice, video)
together does not exceed 100%."
DEFVAL { 0 }
::= { cLQd11bCACConfig 5 }
cLQd11bVideoMaxRoamBandwidth OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects specifies the bandwidth relative
to the maximum allocated bandwidth indicated by
cLQd11bVideoMaxAdmBandwidth, that can be
allocated to roaming clients for video traffic,
when admission control is enabled for 802.11b
interfaces in the controller.
Please note that the write operation on this
object will be successful only if the 802.11b/g
network is not operational. The value configured
through this object takes effect when the 802.11b/g
network is enabled and operational."
DEFVAL { 0 }
::= { cLQd11bCACConfig 6 }
-- ********************************************************************
-- * Configuration of GPR (Gratuitous Probe Response) probe interval
-- * for all 802.11b/g interfaces in the controller
-- ********************************************************************
cLQd11bGprProbeInterval OBJECT-TYPE
SYNTAX Unsigned32 (10..100)
UNITS "TU"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the GPR probe interval
period to be used by all 802.11b/g interfaces in the
controller, when the radios are advertising any
WLAN with GPR support enabled.
Please note that the write operation on this
object will be successful only if the 802.11b/g
network is not operational. The value configured
through this object takes effect when the 802.11b/g
network is enabled."
DEFVAL { 10 }
::= { cLQd11bCACConfig 7 }
cLQd11bVoiceCtrl OBJECT-TYPE
SYNTAX INTEGER {
loadBased(1),
static(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the parameters that can be modified
when admission control is enabled.
loadBased(1) - controller will reserve and manage
max-bandwidth and roaming-bandwidth
based on the load on the WLAN.
static(2) - controller will reserve and
manage max-bandwidth
(cLQd11bVoiceMaxAdmBandwidth)
and roaming-bandwidth
(cLQd11bVoiceMaxRoamBandwidth)
as per user configured values.
When ACM is disabled, admission control will not
be enforced. This may delay voice traffic depending
on the traffic on the WLAN."
DEFVAL { loadBased }
::= { cLQd11bCACConfig 8 }
cLQd11bExpeditedBw OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether expedited BW feature is
enabled or not.
A value of 'true' indicates that the APs advertise
the expedited BW support in their beacons and
association responses.
A value of 'false' indicates that the APs do not
advertise the expedited BW support in their beacons
and association responses."
::= { cLQd11bCACConfig 9 }
cLQd11bEdcaProfile OBJECT-TYPE
SYNTAX INTEGER {
wmmDefault(1),
svpVoice(2),
optimizedVoice(3),
optimizedVideoVoice(4),
customVoice(5),
fastlane(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the EDCA profile to be used
in EDCA parameter . See glossary for EDCA.
wmmDefault(1) - WMM default standard parameters.
svpVoice(2) - Spectralink voice priority parameters.
optimizedVoice(3) - Parameters for voice optimization.
optimizedVideoVoice - Parameters for video and voice
optimization.
customVoice - Parameters for customized voice.
fastlane(6) - parameters for fast lane."
::= { cLQd11bCACConfig 10 }
cLQd11bMacOptimization OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies MAC enhancements for voice,
resulting in improvement in number of voice calls
serviced per access point.
A value of 'true' indicates that MAC optimization will be
enabled.
A value of 'false' indicates that MAC optimization will be
disabled."
::= { cLQd11bCACConfig 11 }
cLQd11bMaxCallLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the max number of CAC Voice Calls
allowed on dot11b radio band. Value of zero denotes no
limit."
::= { cLQd11bCACConfig 12 }
-- ********************************************************************
-- * Configuration for Call Admission Control parameters
-- * for mc2uc in 802.11b interfaces in the controller
-- ********************************************************************
cLQd11bMcastDirectEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether
multicast direct stream on radio should be allowed or not.
A value of 'true' indicates that multicast direct stream
on dot11b radio will be allowed.
A value of 'false' indicates that multicast direct stream
on dot11b radio will be not be allowed."
DEFVAL { true }
::= { cLQd11bCACConfig 13 }
cLQd11bBestEffortAdmission OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether to admit a
media stream in best effort queue or not.
A value of 'true' indicates that media stream in best
effort queue will be allowed.
A value of 'false' indicates that media stream in best
effort queue will not be allowed."
DEFVAL { false }
::= { cLQd11bCACConfig 14 }
cLQd11bRedirectBestEffort OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether a unicast or
multicast only video stream can be redirected
to best effort or not.
A value of 'true' indicates that unicast or multicast only
video stream will be redirected to best effort.
A value of 'false' indicates that unicast or multicast only
video stream will not be redirected to best effort."
DEFVAL { true }
::= { cLQd11bCACConfig 15 }
cLQd11bRadioMaxStreams OBJECT-TYPE
SYNTAX INTEGER (0..20)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum number of
allowed streams per radio for a 802.11b band."
DEFVAL { 0 }
::= { cLQd11bCACConfig 16 }
cLQd11bMaxVideoATPercent OBJECT-TYPE
SYNTAX INTEGER (0..85)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum allowed bandwidth
for video traffic."
::= { cLQd11bCACConfig 17 }
cLQd11bMaxVoiceATPercent OBJECT-TYPE
SYNTAX INTEGER (0..85)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum allowed bandwidth
for voice traffic."
::= { cLQd11bCACConfig 18 }
cLQd11bMaxMediaATPercent OBJECT-TYPE
SYNTAX INTEGER (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum allowed bandwidth
for media traffic."
::= { cLQd11bCACConfig 19 }
cLQd11bMinPhyRate OBJECT-TYPE
SYNTAX CiscoLwappDot11bPhyRates
UNITS "Mbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the minimum rate client needs to have
in order to join media stream."
DEFVAL { 1 }
::= { cLQd11bCACConfig 20 }
cLQd11bClientMaxStreams OBJECT-TYPE
SYNTAX INTEGER (1..16)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum number of allowed
streams per client for a 802.11b band."
DEFVAL { 0 }
::= { cLQd11bCACConfig 21 }
cLQd11bSipCacSupportEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether SIP CAC is supported on
dot11b radio band or not.
A value of 'true' indicates that SIP CAC support on dot11b
radio band will be enabled.
A value of 'false' indicates that SIP CAC support
on dot11b radio band will be disabled."
DEFVAL { false }
::= { cLQd11bCACConfig 22 }
cLQd11bMaxRetryPercent OBJECT-TYPE
SYNTAX INTEGER (0..100)
UNITS "Percent"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum retry percentage
for media traffic on dot11b radio band."
::= { cLQd11bCACConfig 23 }
-- ******************************************************************
-- Configuration of Video CAC Method
-- ******************************************************************
cLQd11bVideoCtrl OBJECT-TYPE
SYNTAX INTEGER {
loadBased(1),
static(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Admission Control method(ACM)
used on dot11b radio band. This object can be modified
when admission control is enabled.
loadBased(1) - Controller will reserve and manage
max-bandwidth and roaming-bandwidth
based on the load on the WLAN.
static(2) - Controller will reserve and manage max-bandwidth
(cLQd11bVoiceMaxAdmBandwidth) and
roaming-bandwidth (cLQd11bVoiceMaxRoamBandwidth)
as per user configured values.
When ACM is disabled, admission control will not
be enforced. This may delay video traffic depending
on the traffic on the WLAN."
DEFVAL { loadBased }
::= { cLQd11bCACConfig 24 }
-- ******************************************************************
-- Configuration of SIP based Video-CAC method
-- ******************************************************************
cLQd11bSipCacVideoEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether SIP based video CAC is enabled
on dot11b radio band or not.
A value of true indicates that SIP based video CAC on
dot11b radio band will be enabled.
A value of false indicates that SIP based video CAC on
dot11b radio band will be disabled."
DEFVAL { false }
::= { cLQd11bCACConfig 25 }
-- ********************************************************************
-- Table to represent (Gratuitous Probe Response) GPR
-- parameters per each WLAN.
-- ********************************************************************
cLQd11GprTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQd11GprEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the GPR information on the
configured WLANs.
There exists a row in this table for each WLAN
configured through cLWlanConfigTable. A row is added
is to this table by the agent when a WLAN is created
by the user through an explicit management action
initiated from a network management station.
Similarly a row gets deleted automatically when the
user deletes the particular WLAN."
::= { cLQd11GprConfig 1 }
cLQd11GprEntry OBJECT-TYPE
SYNTAX CLQd11GprEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a conceptual row in
cLQd11GprTable and corresponds to the
GPR configuration on a WLAN."
INDEX { cLWlanIndex }
::= { cLQd11GprTable 1 }
CLQd11GprEntry ::= SEQUENCE {
cLQd11GprSupport TruthValue
}
cLQd11GprSupport OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether corresponding radios that
advertises this WLAN, sends Gratuitous Probe or not.
A value of true indicates that the corresponding radios
that advertise this WLAN, will send Gratuitous Probe
Response.
A value of false indicates that the corresponding radios
that advertise this WLAN, will not send Gratuitous
Probe Response."
DEFVAL { false }
::= { cLQd11GprEntry 1 }
-- ********************************************************************
-- * CALL admission control statistics
-- ********************************************************************
cLQd11CACStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQd11CACStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the call admission control
metrics collected by observing the voice or video
traffic on the dot11 interface of a particular
AP.
There exists a row in this table for each row
corresponding to a dot11 interface found in
cLApDot11IfTable. A row corresponding to a
dot11 interface is added when an AP joins the
controller. The row gets deleted when the AP
dissociates from the controller."
::= { cLQd11CACStats 1 }
cLQd11CACStatsEntry OBJECT-TYPE
SYNTAX CLQd11CACStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a conceptual row in
CLQd11CACStatsTable and corresponds to the
admission control statistics for a particular
dot11 interface."
INDEX {
cLApSysMacAddress,
cLApDot11IfSlotId
}
::= { cLQd11CACStatsTable 1 }
CLQd11CACStatsEntry ::= SEQUENCE {
cLQd11CacVoiceBwInUse Gauge32,
cLQd11CacVideoBwInUse Gauge32,
cLQd11CacVoiceCallsInProgress Gauge32,
cLQd11CacRoamVoiceCallsInProg Gauge32,
cLQd11CacTotalVoiceCallsAP Counter32,
cLQd11CacTotalRoamCallsAP Counter32,
cLQd11CacVoiceCallsRejectedAP Counter32,
cLQd11CacRoamCallsRejectedAP Counter32,
cLQd11CacRejCallsInsufBw Counter32,
cLQd11CacRejCallsBadParams Counter32,
cLQd11CacRejCallsPhyRate Counter32,
cLQd11CacRejCallsQosPolicy Counter32,
cLQd11SipCacNonRoamCallsInProgress Gauge32,
cLQd11SipCacRoamCallsInProg Gauge32,
cLQd11SipCacTotalNonRoamCallsAP Counter32,
cLQd11SipCacTotalRoamCallsAP Counter32,
cLQd11SipCacNonRoamCallsRejectedInSuffBw Counter32,
cLQd11SipCacRoamCallsRejectedInSuffBw Counter32,
cLQd11SipCacNonRoamCallsRejectedMaxLimit Counter32,
cLQd11SipCacRoamCallsRejectedMaxLimit Counter32,
cLQd11SipCacRejCallsQosPolicy Counter32,
cLQd11SipCacPreferredCallsReceived Counter32,
cLQd11SipCacPreferredCallsAccepted Counter32,
cLQd11KtsCacNonRoamCallsInProgress Gauge32,
cLQd11KtsCacRoamCallsInProg Gauge32,
cLQd11KtsCacTotalNonRoamCallsAP Counter32,
cLQd11KtsCacTotalRoamCallsAP Counter32,
cLQd11KtsCacNonRoamCallsRejectedInSuffBw Counter32,
cLQd11KtsCacRoamCallsRejectedInSuffBw Counter32,
cLQd11CacVideoRoamBwInUse Gauge32,
cLQd11CacVideoTotalBwInUse Gauge32,
cLQd11CacVideoCallsInProgress Gauge32,
cLQd11CacVideoRoamCallsInProg Gauge32,
cLQd11CacVideoTotalCallsAP Counter32,
cLQd11CacVideoTotalRoamCallsAP Counter32,
cLQd11CacVideoCallsRejectedAP Counter32,
cLQd11CacVideoRoamCallsRejectedAP Counter32,
cLQd11CacVideoRejCallsInsufBw Counter32,
cLQd11CacVideoRejCallsBadParams Counter32,
cLQd11CacVideoRejCallsPhyRate Counter32,
cLQd11CacVideoRejCallsQosPolicy Counter32,
cLQd11SipCacVideoCallsInProgress Gauge32,
cLQd11SipCacVideoRoamCallsInProg Gauge32,
cLQd11SipCacVideoTotalCallsAP Counter32,
cLQd11SipCacVideoTotalRoamCallsAP Counter32,
cLQd11SipCacVideoCallsRejectedInSuffBw Counter32,
cLQd11SipCacVideoRoamCallsRejectedInSuffBw Counter32
}
cLQd11CacVoiceBwInUse OBJECT-TYPE
SYNTAX Gauge32 (0..100)
UNITS "Percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the voice bandwidth in use
as a percentage of the bandwidth configured through
cLQd11aVoiceMaxAdmBandwidth or
cLQd11bVoiceMaxAdmBandwidth, depending on the type
of dot11 interface."
::= { cLQd11CACStatsEntry 1 }
cLQd11CacVideoBwInUse OBJECT-TYPE
SYNTAX Gauge32 (0..100)
UNITS "Percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the video bandwidth in use
as a percentage of the bandwidth configured through
cLQd11aVideoMaxAdmBandwidth or
cLQd11bVideoMaxAdmBandwidth, depending on the type
of dot11 interface."
::= { cLQd11CACStatsEntry 2 }
cLQd11CacVoiceCallsInProgress OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the the number of
voice calls currently in progress on dot11
interface."
::= { cLQd11CACStatsEntry 3 }
cLQd11CacRoamVoiceCallsInProg OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
voice calls initiated from roaming clients
currently in progress on dot11 interface."
::= { cLQd11CACStatsEntry 4 }
cLQd11CacTotalVoiceCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
voice calls observed on dot11 interface
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 5 }
cLQd11CacTotalRoamCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
voice and video calls initiated from roaming clients
observed on dot11 interface since
this AP has joined the controller."
::= { cLQd11CACStatsEntry 6 }
cLQd11CacVoiceCallsRejectedAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
voice calls observed as rejected on dot11
interface, since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 7 }
cLQd11CacRoamCallsRejectedAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
voice and video calls initiated from roaming
clients observed as rejected on dot11
interface, since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 8 }
cLQd11CacRejCallsInsufBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
calls observed as rejected on dot11
interface due to insufficient bandwidth, ever
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 9 }
cLQd11CacRejCallsBadParams OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
calls observed as rejected on dot11
interface due to mismatch in call parameters, ever
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 10 }
cLQd11CacRejCallsPhyRate OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
calls observed as rejected on dot11
interface due to mismatch in 802.11 data rates,
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 11 }
cLQd11CacRejCallsQosPolicy OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of
calls observed as rejected on dot11
interface due to restrictions imposed by QoS
policies, since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 12 }
cLQd11SipCacNonRoamCallsInProgress OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming SIP
calls currently in progress on dot11 interface."
::= { cLQd11CACStatsEntry 13 }
cLQd11SipCacRoamCallsInProg OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of SIP calls
initiated from roaming clients currently in progress
on dot11 interface."
::= { cLQd11CACStatsEntry 14 }
cLQd11SipCacTotalNonRoamCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming SIP
calls observed on dot11 interface since this AP
has joined the controller."
::= { cLQd11CACStatsEntry 15 }
cLQd11SipCacTotalRoamCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of SIP calls initiated
from roaming clients observed on dot11 interface
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 16 }
cLQd11SipCacNonRoamCallsRejectedInSuffBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming SIP
calls observed as rejected on dot11 interface
due to insufficient bandwidth, since this AP has
joined the controller."
::= { cLQd11CACStatsEntry 17 }
cLQd11SipCacRoamCallsRejectedInSuffBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of SIP calls
initiated from roaming clients observed as rejected
on this dot11 interface due to insufficient bandwidth,
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 18 }
cLQd11SipCacNonRoamCallsRejectedMaxLimit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming
SIP calls observed as rejected on this dot11 interface
due to maximum limit exceeded, since this AP has
joined the controller."
::= { cLQd11CACStatsEntry 19 }
cLQd11SipCacRoamCallsRejectedMaxLimit OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of roaming SIP calls
observed as rejected on this dot11 interface due to
maximum limit exceeded, since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 20 }
cLQd11SipCacRejCallsQosPolicy OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates the number of SIP calls
observed as rejected on this dot11 interface due
to restrictions imposed by QoS policies, since
this AP has joined the controller."
::= { cLQd11CACStatsEntry 21 }
cLQd11SipCacPreferredCallsReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
preferred calls observed as received on this dot11
interface due to restrictions imposed by QoS
policies, since this AP has joined the controller."
::= { cLQd11CACStatsEntry 22 }
cLQd11SipCacPreferredCallsAccepted OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
preferred calls observed as accepted on this dot11
interface due to restrictions imposed by QoS
policies, since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 23 }
cLQd11KtsCacNonRoamCallsInProgress OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming
KTS calls currently in progress on this dot11
interface."
::= { cLQd11CACStatsEntry 24 }
cLQd11KtsCacRoamCallsInProg OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of KTS calls
initiated from roaming clients currently in
progress on this dot11 interface."
::= { cLQd11CACStatsEntry 25 }
cLQd11KtsCacTotalNonRoamCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming KTS
calls observed on this dot11 interface since this AP
has joined the controller."
::= { cLQd11CACStatsEntry 26 }
cLQd11KtsCacTotalRoamCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of KTS calls
initiated from roaming clients observed on this
dot11 interface since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 27 }
cLQd11KtsCacNonRoamCallsRejectedInSuffBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming KTS
calls observed as rejected on this dot11 interface due
to insufficient bandwidth, since this AP has joined
the controller."
::= { cLQd11CACStatsEntry 28 }
cLQd11KtsCacRoamCallsRejectedInSuffBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of KTS calls
initiated from roaming clients observed as rejected
on this dot11 interface due to insufficient bandwidth,
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 29 }
cLQd11CacVideoRoamBwInUse OBJECT-TYPE
SYNTAX Gauge32 (0..100)
UNITS "Percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the video roaming bandwidth
in use as a percentage of the bandwidth configured
through cLQd11aVideoMaxRoamBandwidth or
cLQd11bVideoMaxRoamBandwidth, depending on the type
of this dot11 interface."
::= { cLQd11CACStatsEntry 30 }
cLQd11CacVideoTotalBwInUse OBJECT-TYPE
SYNTAX Gauge32 (0..100)
UNITS "Percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the total video bandwidth in
use."
::= { cLQd11CACStatsEntry 31 }
cLQd11CacVideoCallsInProgress OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls currently in progress on this dot11
interface."
::= { cLQd11CACStatsEntry 32 }
cLQd11CacVideoRoamCallsInProg OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls initiated from roaming clients
currently in progress on this dot11 interface."
::= { cLQd11CACStatsEntry 33 }
cLQd11CacVideoTotalCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls observed on this dot11 interface
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 34 }
cLQd11CacVideoTotalRoamCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls initiated from roaming clients
observed on this dot11 interface since
this AP has joined the controller."
::= { cLQd11CACStatsEntry 35 }
cLQd11CacVideoCallsRejectedAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls observed as rejected on this dot11
interface, since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 36 }
cLQd11CacVideoRoamCallsRejectedAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls initiated from roaming
clients observed as rejected on this dot11
interface, since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 37 }
cLQd11CacVideoRejCallsInsufBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls observed as rejected on this dot11
interface due to insufficient bandwidth, ever
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 38 }
cLQd11CacVideoRejCallsBadParams OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls observed as rejected on this dot11
interface due to mismatch in call parameters, ever
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 39 }
cLQd11CacVideoRejCallsPhyRate OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls observed as rejected on this dot11
interface due to mismatch in 802.11 data rates,
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 40 }
cLQd11CacVideoRejCallsQosPolicy OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the count of the number of
video calls observed as rejected on this dot11
interface due to restrictions imposed by QoS
policies, ever since this AP has joined the
controller."
::= { cLQd11CACStatsEntry 41 }
cLQd11SipCacVideoCallsInProgress OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming
SIP video calls currently in progress on this dot11
interface."
::= { cLQd11CACStatsEntry 42 }
cLQd11SipCacVideoRoamCallsInProg OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of SIP video calls
initiated from roaming clients currently in progress
on this dot11 interface."
::= { cLQd11CACStatsEntry 43 }
cLQd11SipCacVideoTotalCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming SIP
video calls observed on this dot11 interface since
this AP has joined the controller."
::= { cLQd11CACStatsEntry 44 }
cLQd11SipCacVideoTotalRoamCallsAP OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of SIP video calls
initiated from roaming clients observed on this dot11
interface since this AP has joined the controller."
::= { cLQd11CACStatsEntry 45 }
cLQd11SipCacVideoCallsRejectedInSuffBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of non-roaming SIP
video calls observed as rejected on this dot11
interface due to insufficient bandwidth, since this
AP has joined the controller."
::= { cLQd11CACStatsEntry 46 }
cLQd11SipCacVideoRoamCallsRejectedInSuffBw OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the number of SIP video calls
initiated from roaming clients observed as rejected
on this dot11 interface due to insufficient bandwidth,
since this AP has joined the controller."
::= { cLQd11CACStatsEntry 47 }
-- ********************************************************************
-- * Voice stats per radio
-- ********************************************************************
cLQd11VoiceStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQd11VoiceStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the voice statistics
calculated for each radio on an AP.
An entry is automatically added by the controller
when a voice call is successfully placed.
Entry is deleted when AP disassociates the
controller."
::= { cLQd11VoiceStats 1 }
cLQd11VoiceStatsEntry OBJECT-TYPE
SYNTAX CLQd11VoiceStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table represents voice related
statistics for each radio on an AP.
Entries are removed when the AP disassociates from the
controller."
INDEX {
cLApSysMacAddress,
cLApDot11IfSlotId
}
::= { cLQd11VoiceStatsTable 1 }
CLQd11VoiceStatsEntry ::= SEQUENCE {
cLQd11VoiceCallCounts Counter32,
cLQd11CacVoiceCallTimePeriod TimeIntervalSec
}
cLQd11VoiceCallCounts OBJECT-TYPE
SYNTAX Counter32
UNITS "calls"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates cumulative number of successful
VoIP calls placed using this radio."
::= { cLQd11VoiceStatsEntry 1 }
cLQd11CacVoiceCallTimePeriod OBJECT-TYPE
SYNTAX TimeIntervalSec
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates cumulative call proceed time."
::= { cLQd11VoiceStatsEntry 2 }
-- ********************************************************************
-- * Per WLAN voice config
-- ********************************************************************
cLQVoiceWlanConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQVoiceWlanConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains per WLAN voice related
configuration.
There is a row in this table for every WLAN
configured through cLWlanConfigTable. A row is added
to this table by the agent when a WLAN is created
by the user through an explicit management action
initiated from a network management station.
Similarly a row gets deleted automatically when the
user deletes the particular WLAN."
::= { cLQVoiceWlanConfig 1 }
cLQVoiceWlanConfigEntry OBJECT-TYPE
SYNTAX CLQVoiceWlanConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents information about voice
configuration for a particular WLAN."
INDEX { cLWlanIndex }
::= { cLQVoiceWlanConfigTable 1 }
CLQVoiceWlanConfigEntry ::= SEQUENCE {
cLQVoiceWlanConfigDetectVoipCallFailure TruthValue
}
cLQVoiceWlanConfigDetectVoipCallFailure OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether the corresponding radios that
advertise this WLAN, will snoop voice packets
to detect call failure or not.
A value of true indicates that the corresponding radios
that advertise this WLAN will snoop voice packets
to detect call failure and report by sending trap.
A value of false indicates that the corresponding radios
that advertise this WLAN will not detect call failure
and hence will not send trap."
DEFVAL { false }
::= { cLQVoiceWlanConfigEntry 1 }
-- ********************************************************************
-- * Client table - voice related objects
-- ********************************************************************
cLQVoiceClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQVoiceClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains voice related client properties.
There exists a row in this table for each associated
voice clients.
A row is added to this table by the
agent when a voice client gets associated.
Similarly, a row gets deleted automatically when the
voice client gets disassociated."
::= { cLQVoiceClient 1 }
cLQVoiceClientEntry OBJECT-TYPE
SYNTAX CLQVoiceClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table represents voice call management
information for a particular client."
INDEX { cldcClientMacAddress }
::= { cLQVoiceClientTable 1 }
CLQVoiceClientEntry ::= SEQUENCE {
cLQVoiceClientCallingNumber SnmpAdminString,
cLQVoiceClientLastCalledNumber SnmpAdminString,
cLQVoiceClientLastCallFailureReasonCode INTEGER
}
cLQVoiceClientCallingNumber OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates calling number of this
voice client."
::= { cLQVoiceClientEntry 1 }
cLQVoiceClientLastCalledNumber OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates last called number from this
voice client."
::= { cLQVoiceClientEntry 2 }
cLQVoiceClientLastCallFailureReasonCode OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
normalFailure(2),
roamFailure(3),
maxLimitExceeded(4),
sipPrefCallNoBw(5),
badRequest(400),
unauthorized(401),
paymentRequired(402),
forbidden(403),
notFound(404),
methodNotallowed(405),
notAcceptable(406),
proxyAuthenticationRequired(407),
requestTimeout(408),
conflict(409),
gone(410),
lengthRequired(411),
requestEntityTooLarge(413),
requestURITooLarge(414),
unsupportedMdediaType(415),
badExtension(420),
temporarilyNotAvailable(480),
callLegDoesNotExist(481),
loopDetected(482),
tooManyHops(483),
addressIncomplete(484),
ambiguous(485),
busy(486),
internalServerError(500),
notImplemented(501),
badGateway(502),
serviceUnavailable(503),
serverTimeout(504),
versionNotSupported(505),
busyEverywhere(600),
decline(603),
doesNotExistAnywhere(604),
sessionNotAcceptable(606)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents last VoIP failure reason code
of this voice client.
These reason codes are taken from SIP standards.
unknown - Unknown error
normalFailure - Call failed for insufficient bandwidth
roamFailure - SIP call failed during roaming
maxLimitExceeded - Maximum SIP call permissible limit
was exceeded.
sipPrefCallNoBw - SIP Preferred call failed for
insufficient bandwidth
badRequest - The request could not be understood
due to malformed syntax.
unauthorized - The request requires user
authentication.
paymentRequired - Reserved for future.
forbidden - The server understood the request,
but is refusing to fulfill it.
notFound - The server has definitive information
that the user does not exist at the domain specified in the
Request-URI.
methodNotallowed - The method specified in the
Request-Line is understood, but not allowed for the address
identified by the Request-URI.
notAcceptable - The resource identified by the request
is only capable of generating response entities that have
content characteristics not acceptable according to the Accept
header field sent in the request.
proxyAuthenticationRequired - This code is similar to 401
(Unauthorized), but indicates that the client MUST first
authenticate itself with the proxy.
requestTimeout - The server could not produce a
response within a suitable amount of time, for example,
if it could not determine the location of the user in time.
conflict - This is used to indicate that the
request could not be completed due to a conflict with the
current state of the resource.
gone - The requested resource is no longer
available at the server and no forwarding address is known.
lengthRequired - The server is refusing to process a
request because the request entity-body is larger than the
server is willing or able to process.
requestEntityTooLarge - The server is refusing to process a
request because the request entity-body is larger than the
server is willing or able to process.
requestURITooLarge - The server is refusing to service the
request because the Request-URI is longer than the server is
willing to interpret.
unsupportedMediaType - The server is refusing to service the
request because the message body of the request is in a format
not supported by the server for the requested method.
badExtension - The server did not understand the
protocol extension specified in a Proxy-Require or Require
header field.
temporarilyNotAvailable - The callee's end system was contacted
successfully but the callee is currently unavailable.
callLegDoesNotExist - This status indicates that the UAS
received a request that does not match any existing dialog
or transaction.
loopDetected - The server has detected a loop.
tooManyHops - The server received a request that
contains a Max-Forwards header field with the value zero.
addressIncomplete - The server received a request with a
Request-URI that was incomplete.
ambiguous - The Request-URI was ambiguous.
busy - The callee's end system was contacted
successfully, but the callee is currently not willing or able
to take additional calls at this end system.
internalServerError - The server encountered an unexpected
condition that prevented it from fulfilling the request.
notImplemented - The server does not support the
functionality required to fulfill the request.
badGateway - The server, while acting as a gateway
or proxy, received an invalid response from the downstream
server it accessed in attempting to fulfill the request.
serviceUnavailable - The server is temporarily unable to
process the request due to a temporary overloading or
maintenance of the server.
serverTimeout - The server did not receive a timely
response from an external server it accessed in attempting to
process the request.
versionNotSupported - The server does not support, or
refuses to support, the SIP protocol version that was used
in the request.
busyEverywhere - The callee's end system was contacted
successfully but the callee is busy and does not wish to take
the call at this time.
decline - The callee's machine was successfully
contacted but the user explicitly does not wish to or cannot
participate.
doesNotExistAnywhere - The server has authoritative
information that the user indicated in the Request-URI
does not exist anywhere.
sessionNotAcceptable - The user's agent was contacted
successfully but some aspects of the session description
such as the requested media, bandwidth, or addressing
style were not acceptable."
::= { cLQVoiceClientEntry 3 }
-- ********************************************************************
-- * Client table - Media related objects
-- ********************************************************************
cLQMediaClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQMediaClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains media related client
properties.
There exists a row in this table for each associated
media clients. A row is added to this table by the
agent when a client gets associated
Similarly a row gets deleted automatically when the
client gets disassociated."
::= { cLQMediaClient 1 }
cLQMediaClientEntry OBJECT-TYPE
SYNTAX CLQMediaClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table represents a conceptual row in
cLQMediaClientTable and corresponds to media
properties of client."
INDEX {
cLQMStreamName,
cLQVMediaClientDestIpAddrType,
cLQVMediaClientDestIpAddr,
cldcClientMacAddress
}
::= { cLQMediaClientTable 1 }
CLQMediaClientEntry ::= SEQUENCE {
cLQVMediaClientDestIpAddrType InetAddressType,
cLQVMediaClientDestIpAddr InetAddress,
cLQVMediaClientSrcIpAddrType InetAddressType,
cLQVMediaClientSrcIpAddr InetAddress,
cLQVMediaClientApMacAddress MacAddress,
cLQVMediaClientWlanIndex Unsigned32,
cLQVMediaClientRadioType INTEGER,
cLQVMediaClientQos INTEGER,
cLQVMediaClientDecision INTEGER
}
cLQVMediaClientDestIpAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents multicast destination IP address
type."
::= { cLQMediaClientEntry 1 }
cLQVMediaClientDestIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents multicast destination IP address."
::= { cLQMediaClientEntry 2 }
cLQVMediaClientSrcIpAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents multicast source IP address type."
::= { cLQMediaClientEntry 3 }
cLQVMediaClientSrcIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents multicast source IP address."
::= { cLQMediaClientEntry 4 }
cLQVMediaClientApMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the MAC address of the AP to which
client is connected."
::= { cLQMediaClientEntry 5 }
cLQVMediaClientWlanIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents an unique instance of
a WLAN on the controller to which client is connected.
The value 513-517 indicates wired clients."
::= { cLQMediaClientEntry 6 }
cLQVMediaClientRadioType OBJECT-TYPE
SYNTAX INTEGER {
radio80211bg(1),
radio80211a(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents client radio type.
radio80211bg(1) - This indicates the client radio type is
802.11bg.
radio80211a(2) - This indicates the client radio type is
802.11a."
::= { cLQMediaClientEntry 7 }
cLQVMediaClientQos OBJECT-TYPE
SYNTAX INTEGER {
besteffort(1),
background(2),
undefined(3),
excellenteffort(4),
ctrlload(5),
video(6),
voice(7),
network(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents client QoS.
besteffort(1) - This indicates that packets for this client
will be sent at besteffort.
background(2) - This indicates that packets for this client
will be sent at lowest priority.
undefined(3) - This indicates that packets for this client
will be sent with unknown priority.
excellenteffort(4) - This indicates that packets for this
client will be sent at DSCP24
priority.
ctrlload(5) - Provides a service better than best effort
and low delay service under light to moderate
network loads.
video(6) - This indicates that packets for this client will
be sent at video priority.
voice(7) - This indicates that packets for this client will
be sent at voice priority.
network(8) - This indicates that packets for this client
will be sent at the network critical
priority."
DEFVAL { 6 }
::= { cLQMediaClientEntry 8 }
cLQVMediaClientDecision OBJECT-TYPE
SYNTAX INTEGER {
deny(1),
admit(2),
badClientDeny(3),
badClientDemote(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the policy of this media client.
deny(1) - The client's media stream decision will be
denied by the controller.
admit(2) - The client's media stream decision will be
admitted by the controller.
badClientDeny(3) - If it exceeds configured bandwidth,
either the video will not start or the
client might be classified as a bad
client.
badClientDemote(4) - The bad client video will be demoted
for better effort QoS or subject to
denial."
::= { cLQMediaClientEntry 9 }
cLQMediaClientHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQMediaClientHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains media related client properties."
::= { cLQMediaClient 2 }
cLQMediaClientHistoryEntry OBJECT-TYPE
SYNTAX CLQMediaClientHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a conceptual row in
cLQMediaClientHistoryTable and corresponds to media
properties of client."
INDEX { cLQVMediaClientHistTimeStamp }
::= { cLQMediaClientHistoryTable 1 }
CLQMediaClientHistoryEntry ::= SEQUENCE {
cLQVMediaClientHistTimeStamp TimeStamp,
cLQVMediaClientHistClientMacAddress MacAddress,
cLQVMediaClientHistApMacAddress MacAddress,
cLQVMediaClientHistSlotId Unsigned32,
cLQVMediaClientHistSrcIpAddr IpAddress,
cLQVMediaClientHistDestIpAddr IpAddress,
cLQVMediaClientHistDecision INTEGER,
cLQVMediaClientHistLastFailureReasonCode INTEGER,
cLQVMediaClientHistWlanIndex Unsigned32,
cLQVMediaClientHistRadioType INTEGER,
cLQVMediaClientHistQos INTEGER,
cLQVMediaClientHistCfgBw Unsigned32,
cLQVMediaClientHistCurrentRate Unsigned32,
cLQVMediaClientHistVideoPktSize Unsigned32,
cLQVMediaClientHistVideoUtil Unsigned32,
cLQVMediaClientHistVoiceUtil Unsigned32,
cLQVMediaClientHistChannelUtil Unsigned32,
cLQVMediaClientHistQueueUtil Unsigned32,
cLQVMediaClientHistVideoPps Unsigned32,
cLQVMediaClientHistVideoDelay Unsigned32,
cLQVMediaClientHistPktLossDiscard Unsigned32,
cLQVMediaClientHistPktLossFail Unsigned32,
cLQVMediaClientHistNumVideoStreams Unsigned32,
cLQVMediaClientHistCacEnable INTEGER,
cLQVMediaClientHistStreamName SnmpAdminString,
cLQVMediaClientHistSrcInetAddrType InetAddressType,
cLQVMediaClientHistSrcInetAddr InetAddress,
cLQVMediaClientHistDestInetAddrType InetAddressType,
cLQVMediaClientHistDestInetAddr InetAddress
}
cLQVMediaClientHistTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents one instance of
the timestamp in history for which the client
admit/deny happens."
::= { cLQMediaClientHistoryEntry 1 }
cLQVMediaClientHistClientMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the MAC address of the
client."
::= { cLQMediaClientHistoryEntry 2 }
cLQVMediaClientHistApMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the MAC address of the
AP."
::= { cLQMediaClientHistoryEntry 3 }
cLQVMediaClientHistSlotId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the unique identifier for media
client's slot id."
::= { cLQMediaClientHistoryEntry 4 }
cLQVMediaClientHistSrcIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents media client's multicast source IP
address."
::= { cLQMediaClientHistoryEntry 5 }
cLQVMediaClientHistDestIpAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents media client's multicast destination
IP address."
::= { cLQMediaClientHistoryEntry 6 }
cLQVMediaClientHistDecision OBJECT-TYPE
SYNTAX INTEGER {
deny(1),
admit(2),
badClientDeny(3),
badClientDemote(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the policy of this media client.
deny(1) - The client's media stream decision will be
denied by the controller.
admit(2) - The client's media stream decision will be
admitted by the controller.
badClientDeny(3) - If it exceeds configured bandwidth,
either the video will not start or the
client might be classified as a bad
client.
badClientDemote(4) - The bad client video will be demoted
for better effort QoS or subject to
denial."
::= { cLQMediaClientHistoryEntry 7 }
cLQVMediaClientHistLastFailureReasonCode OBJECT-TYPE
SYNTAX INTEGER {
enoughBw(1),
notEnoughBw(2),
bwViolation(3),
radioOverSubscribe(4),
badClientLink(5),
policyNotAllowed(6),
otherErrors(7),
clientDemote(8),
clientTimeout(9),
clientLeave(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents last failure reason code
of this media client.
enoughBw(1) - Radio can handle additional client traffic.
Hence, allowing client admission during RRC
admission or Re-RRC phase.
notEnoughBw(2) - Radio cannot handle additional client
traffic. Thus it will delist(put into best
effort queue) or deny client.
bwViolation(3) - After Re-RRC calculations, it is determined
that client has done stream config
violation. Thus, it will be delisted or
denied.
radioOverSubscribe(4) - Client will be denied when
radio resources are fully utilized.
badClientLink(5) - If client traffic is sent at lower data
rate or number of retries exceed
threshold, it will be classified as bad
client.
policyNotAllowed(6) - Client subscription has violated
policy configured.
otherErrors(7) - During RRC admission or Re-RRC phase,
client joining is denied because of
abnormal conditions, such as not able to
retrieve client data for calculation.
clientDemote(8) - During Re-RRC calculation, client is
demoted to best-effort queue because the
radio is too busy.
clientTimeout(9) - Client is considered for timeout and
removed from databse when no stream
update for the client is available before
the timer (15 mins by default) expires.
clientLeave(10) - Client leaves the stream in normal
condition."
::= { cLQMediaClientHistoryEntry 8 }
cLQVMediaClientHistWlanIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..517)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object uniquely identifies one instance of
a WLAN on the controller. The value 513-517 indicates
wired clients."
::= { cLQMediaClientHistoryEntry 9 }
cLQVMediaClientHistRadioType OBJECT-TYPE
SYNTAX INTEGER {
radio80211bg(1),
radio80211a(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object denotes media client's radio type.
radio80211bg(1) - This indicates the client radio type is
802.11bg.
radio80211a(2) - This indicates the client radio type is
802.11a."
::= { cLQMediaClientHistoryEntry 10 }
cLQVMediaClientHistQos OBJECT-TYPE
SYNTAX INTEGER {
besteffort(1),
background(2),
undefined(3),
excellenteffort(4),
ctrlload(5),
video(6),
voice(7),
network(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents media client QoS for the stream.
besteffort(1) - This indicates that packets for this client
will be sent at besteffort.
background(2) - This indicates that packets for this client
will be sent at lowest priority.
undefined(3) - This indicates that packets for this client
will be sent with unknown priority.
excellenteffort(4) - This indicates that packets for this
client will be sent at DSCP24
priority.
ctrlload(5) - Provides a service better than best effort
and low delay service under light to moderate
network loads.
video(6) - This indicates that packets for this client will
be sent at video priority.
voice(7) - This indicates that packets for this client will
be sent at voice priority.
network(8) - This indicates that packets for this client
will be sent at the network critical
priority."
DEFVAL { 6 }
::= { cLQMediaClientHistoryEntry 11 }
cLQVMediaClientHistCfgBw OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's configured
stream bandwidth."
::= { cLQMediaClientHistoryEntry 12 }
cLQVMediaClientHistCurrentRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the current rate of media client."
::= { cLQMediaClientHistoryEntry 13 }
cLQVMediaClientHistVideoPktSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's video packet
size."
::= { cLQMediaClientHistoryEntry 14 }
cLQVMediaClientHistVideoUtil OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's video util."
::= { cLQMediaClientHistoryEntry 15 }
cLQVMediaClientHistVoiceUtil OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's voice util."
::= { cLQMediaClientHistoryEntry 16 }
cLQVMediaClientHistChannelUtil OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's channel util."
::= { cLQMediaClientHistoryEntry 17 }
cLQVMediaClientHistQueueUtil OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's queue util."
::= { cLQMediaClientHistoryEntry 18 }
cLQVMediaClientHistVideoPps OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's video packets per
second."
::= { cLQMediaClientHistoryEntry 19 }
cLQVMediaClientHistVideoDelay OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's video delay
severe."
::= { cLQMediaClientHistoryEntry 20 }
cLQVMediaClientHistPktLossDiscard OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's packet loss
discard."
::= { cLQMediaClientHistoryEntry 21 }
cLQVMediaClientHistPktLossFail OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the media client's packet loss
fail."
::= { cLQMediaClientHistoryEntry 22 }
cLQVMediaClientHistNumVideoStreams OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the number of media client's video
streams."
::= { cLQMediaClientHistoryEntry 23 }
cLQVMediaClientHistCacEnable OBJECT-TYPE
SYNTAX INTEGER {
video(1),
voice(2),
videoAndVoice(3),
none(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the CAC state of media client.
video(1) - Call admission is allowed only for video.
voice(2) - Call admission is allowed only for voice.
videoAndVoice(3) - Call admission is allowed for both video
and voice.
none(4) - Call admission is completely denied."
::= { cLQMediaClientHistoryEntry 24 }
cLQVMediaClientHistStreamName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the name of the media stream the
client was admitted at the particular timestamp."
::= { cLQMediaClientHistoryEntry 25 }
cLQVMediaClientHistSrcInetAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents multicast destination start address
type of media client."
::= { cLQMediaClientHistoryEntry 26 }
cLQVMediaClientHistSrcInetAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents media client's multicast destination
start address."
::= { cLQMediaClientHistoryEntry 27 }
cLQVMediaClientHistDestInetAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents media client's multicast destination
end address type."
::= { cLQMediaClientHistoryEntry 28 }
cLQVMediaClientHistDestInetAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents media client's multicast destination
end address."
::= { cLQMediaClientHistoryEntry 29 }
cLQMediaMulticastClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQMediaMulticastClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents media related client
properties for multicast clients.
There exists a row in this table for each associated
media clients. A row is added to this table by the
agent when a client gets associated
Similarly a row gets deleted automatically when the
client gets disassociated."
::= { cLQMediaClient 3 }
cLQMediaMulticastClientEntry OBJECT-TYPE
SYNTAX CLQMediaMulticastClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a conceptual row in
cLQMediaMulticastClientTable and corresponds to media
properties of client."
INDEX {
cLQMStreamName,
cLQVMediaClientMCGrpIpAddrType,
cLQVMediaClientMCGrpIpAddr,
cldcClientMacAddress
}
::= { cLQMediaMulticastClientTable 1 }
CLQMediaMulticastClientEntry ::= SEQUENCE {
cLQVMediaClientMCGrpIpAddrType InetAddressType,
cLQVMediaClientMCGrpIpAddr InetAddress,
cLQVMediaClientVlanId Unsigned32,
cLQVMediaMCClientApName SnmpAdminString,
cLQVMediaClientMCUCStatus SnmpAdminString
}
cLQVMediaClientMCGrpIpAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents multicast destination IP address
type."
::= { cLQMediaMulticastClientEntry 1 }
cLQVMediaClientMCGrpIpAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents multicast destination IP address."
::= { cLQMediaMulticastClientEntry 2 }
cLQVMediaClientVlanId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the VLAN id of the
client."
::= { cLQMediaMulticastClientEntry 3 }
cLQVMediaMCClientApName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the unique access point to
which the multicast client is connected."
::= { cLQMediaMulticastClientEntry 4 }
cLQVMediaClientMCUCStatus OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents whether the multicast client has
multicast-to-unicast feature enabled."
::= { cLQMediaMulticastClientEntry 5 }
-- ********************************************************************
-- * SIP CALL admission control configurations
-- ********************************************************************
cLQd11SipCacConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQd11SipCacConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the information about the
SIP CAC configuration corresponding to the dot11 bands of
the APs that have joined the controller.
The parameters specify how the SIP call reserves
CAC bandwidth."
::= { cLQd11SipCacConfig 1 }
cLQd11SipCacConfigEntry OBJECT-TYPE
SYNTAX CLQd11SipCacConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table represents SIP CAC configuration
for a particular type of wireless interface."
INDEX { cLApDot11IfType }
::= { cLQd11SipCacConfigTable 1 }
CLQd11SipCacConfigEntry ::= SEQUENCE {
cLQd11SipCacConfigCodecType INTEGER,
cLQd11SipCacConfigBw Unsigned32,
cLQd11SipCacConfigVoiceSampleSize Unsigned32,
cLQd11SipCacMaxPossibleVoiceCalls Unsigned32,
cLQd11SipCacMaxPossibleReservedRoamingCalls Unsigned32
}
cLQd11SipCacConfigCodecType OBJECT-TYPE
SYNTAX INTEGER {
userDefined(1),
g711(2),
g729(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the configured codec for SIP Cac
configuration of the dot11 band for the APs associated
with this controller. Codec determines the bandwidth to
be reserved for voice call.
userDefined(1) - User defines the bandwidth,
cLQd11SipCacConfigBw has to be configured.
g711(2) - standard Codec G711.
g729(3) - standard Codec G729."
DEFVAL { g711 }
::= { cLQd11SipCacConfigEntry 1 }
cLQd11SipCacConfigBw OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the configured bandwidth in kbps
for SIP CAC configuration of the dot11
band for the APs associated with this controller.
This is configurable only if cLQd11SipCacConfigCodecType
is 'userDefined'"
::= { cLQd11SipCacConfigEntry 2 }
cLQd11SipCacConfigVoiceSampleSize OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the configured voice sample size
in milliseconds for SIP CaC configuration of the dot11 band
for the APs associated with this controller."
::= { cLQd11SipCacConfigEntry 3 }
cLQd11SipCacMaxPossibleVoiceCalls OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the maximum possible voice calls
that can be made with respect to the current SIP CAC
configuration."
::= { cLQd11SipCacConfigEntry 4 }
cLQd11SipCacMaxPossibleReservedRoamingCalls OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the maximum possible reserved
roaming calls that can be made with respect to the current
SIP CAC configuration."
::= { cLQd11SipCacConfigEntry 5 }
-- ********************************************************************
-- Table to represent Media stream config
-- parameters per stream.
-- ********************************************************************
cLQMStreamTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQMStreamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the media stream configuration."
::= { cLQMediaStreamConfig 1 }
cLQMStreamEntry OBJECT-TYPE
SYNTAX CLQMStreamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table represents a conceptual row in
cLQMStreamTable and corresponds to the media stream
configuration."
INDEX { cLQMStreamName }
::= { cLQMStreamTable 1 }
CLQMStreamEntry ::= SEQUENCE {
cLQMStreamName SnmpAdminString,
cLQMStreamRowStatus RowStatus,
cLQMStreamDestIPStartAddr IpAddress,
cLQMStreamDestIPEndAddr IpAddress,
cLQMStreamstate TruthValue,
cLQMStreamRrcExpBw Unsigned32,
cLQMStreamRrcAvgPkt Unsigned32,
cLQMStreamReRrc TruthValue,
cLQMStreamRrcQos INTEGER,
cLQMStreamRrcType INTEGER,
cLQMStreamRrcPriority INTEGER,
cLQMStreamRrcViolation INTEGER,
cLQMStreamRrcPolicy TruthValue,
cLQMStreamDestStartInetAddrType InetAddressType,
cLQMStreamDestStartInetAddr InetAddress,
cLQMStreamDestEndInetAddrType InetAddressType,
cLQMStreamDestEndInetAddr InetAddress
}
cLQMStreamName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the name of the media stream.
This is the unique identifier for the stream."
::= { cLQMStreamEntry 1 }
cLQMStreamRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the status column for this row and is used to
create and delete specific instances of rows in this
table.
The following objects are mandatory for successful
creation of an entry:cLQMStreamName."
::= { cLQMStreamEntry 2 }
cLQMStreamDestIPStartAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies multicast start IP address."
::= { cLQMStreamEntry 3 }
cLQMStreamDestIPEndAddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies multicast destination end IP
address."
::= { cLQMStreamEntry 4 }
cLQMStreamstate OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies media stream state.
A value of 'true' indicates that media stream state is
enabled.
A value of 'false' indicates that media stream state is
disabled."
DEFVAL { false }
::= { cLQMStreamEntry 5 }
cLQMStreamRrcExpBw OBJECT-TYPE
SYNTAX Unsigned32 (1..35000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies Resource Reservation Control(RRC)
bandwidth utilization."
DEFVAL { 500 }
::= { cLQMStreamEntry 6 }
cLQMStreamRrcAvgPkt OBJECT-TYPE
SYNTAX Unsigned32 (100..1500)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies RRC average packet size."
DEFVAL { 1200 }
::= { cLQMStreamEntry 7 }
cLQMStreamReRrc OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether re-RRC calculations are
enabled or disabled.
A value of 'true' indicates that re-RRC will be enabled .
A value of 'false' indicates that re-RRC will be disabled."
DEFVAL { true }
::= { cLQMStreamEntry 8 }
cLQMStreamRrcQos OBJECT-TYPE
SYNTAX INTEGER {
besteffort(1),
background(2),
undefined(3),
excellenteffort(4),
ctrlload(5),
video(6),
voice(7),
network(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies RRC QoS queue information.
besteffort(1) - This indicates that packets for this client
will be sent at besteffort.
background(2) - This indicates that packets for this client
will be sent at lowest priority.
undefined(3) - This indicates that packets for this client
will be sent with unknown priority.
excellenteffort(4) - This indicates that packets for this
client will be sent at DSCP24
priority.
ctrlload(5) - Provides a service better than best effort
and low delay service under light to moderate
network loads.
video(6) - This indicates that packets for this client will
be sent at video priority.
voice(7) - This indicates that packets for this client will
be sent at voice priority.
network(8) - This indicates that packets for this client
will be sent at the network critical
priority."
DEFVAL { voice }
::= { cLQMStreamEntry 9 }
cLQMStreamRrcType OBJECT-TYPE
SYNTAX INTEGER {
mc2uc(1),
m-only(2),
unicast(3),
disabled(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies RRC media stream type.
mc2uc(1) - Multicast to unicast enabled.
m-only(2) - Only multicast enabled.
unicast(3) - Unicast enabled.
disabled(4) - Neither multicast nor unicast enabled."
DEFVAL { mc2uc }
::= { cLQMStreamEntry 10 }
cLQMStreamRrcPriority OBJECT-TYPE
SYNTAX INTEGER (1..8)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies RRC Priority bit set within media
stream."
DEFVAL { 4 }
::= { cLQMStreamEntry 11 }
cLQMStreamRrcViolation OBJECT-TYPE
SYNTAX INTEGER {
fallback(1),
drop(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies RRC violation. After re-RRC, if media
stream violates profile then whether to stash it into best
effort or drop it.
fallback(1) - If the media stream violates, then it will be
demoted to best effort.
drop(2) - If the media stream violates then the stream will
be denied/dropped."
DEFVAL { 2 }
::= { cLQMStreamEntry 12 }
cLQMStreamRrcPolicy OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether media stream is admitted
or denied.
A value of 'true' indicates that media stream will be
admitted .
A value of 'false' indicates that media stream will be
denied."
DEFVAL { false }
::= { cLQMStreamEntry 13 }
cLQMStreamDestStartInetAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies multicast destination start address
type."
::= { cLQMStreamEntry 14 }
cLQMStreamDestStartInetAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies multicast destination start address."
::= { cLQMStreamEntry 15 }
cLQMStreamDestEndInetAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies multicast destination end address
type."
::= { cLQMStreamEntry 16 }
cLQMStreamDestEndInetAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies multicast destination end address."
::= { cLQMStreamEntry 17 }
cLQMStreamSdpConfig OBJECT IDENTIFIER
::= { cLQMediaStreamConfig 2 }
cLQMStreamSdpUrl OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..128))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the URL field of Session Description
Protocol message."
::= { cLQMStreamSdpConfig 1 }
cLQMStreamSdpEmail OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies email field of Session Description
Protocol message."
::= { cLQMStreamSdpConfig 2 }
cLQMStreamSdpPhone OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..30))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies phone field of Session Description
Protocol (SDP) message."
::= { cLQMStreamSdpConfig 3 }
cLQMStreamSdpNote OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..128))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies note field of Session Description
Protocol (SDP) note."
::= { cLQMStreamSdpConfig 4 }
cLQMStreamSdpStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the Session Description
Protocol (SDP) status.
A value of 'true' indicates that SDP is enabled.
A value of 'false' indicated that SDP is diabled."
::= { cLQMStreamSdpConfig 5 }
cLQMStreamRrcGlobal OBJECT IDENTIFIER
::= { cLQMediaStreamConfig 3 }
cLQMStreamRrcGlobalState OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether media stream feature is
globally enabled or not.
A 'true' value indicates that media stream feature is
enabled.
A 'false' value indicates that media stream feature is
disabled."
DEFVAL { false }
::= { cLQMStreamRrcGlobal 1 }
cLQPreferredCallTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQPreferredCallEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the preferred call configuration."
::= { cLQPreferredCallConfig 1 }
cLQPreferredCallEntry OBJECT-TYPE
SYNTAX CLQPreferredCallEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table represents a conceptual row in
cLQPreferredCallTable and corresponds to the preferred call
of the user."
INDEX { cLQPreferredCallIndex }
::= { cLQPreferredCallTable 1 }
CLQPreferredCallEntry ::= SEQUENCE {
cLQPreferredCallIndex Unsigned32,
cLQPreferredCallNumber SnmpAdminString,
cLQPreferredCallRowStatus RowStatus
}
cLQPreferredCallIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..6)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the index of the preferred call
configured by the user. When the call comes to any of these
numbers, even if there is no bandwidth available in the
configured voice pool, WLC should facilitate the urgency
of these calls in any way possible without potentially
altering the quality of the existing calls.
This is supported only for those clients which
use SIP based CAC for bandwidth allocation in the WLC."
::= { cLQPreferredCallEntry 1 }
cLQPreferredCallNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the preferred call number
configured by the user. When the call comes to any of these
numbers, even if there is no bandwidth available in the
configured voice pool,WLC should facilitate the urgency of
these calls in any way possible without potentially
altering the quality of the existing calls. This is
supported only for those clients which use SIP based CAC
for bandwidth allocation in the WLC."
::= { cLQPreferredCallEntry 2 }
cLQPreferredCallRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the status column for this row and used
to create and delete specific instances of rows
in this table.
The following objects are mandatory for successful
creation of an entry:cLQPreferredCallIndex"
::= { cLQPreferredCallEntry 3 }
cLQoSProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the configurable priority related QoS
paramaters for the WLAN. There exists a row in this table
for each QoS profile type."
::= { cLQoSProfileConfig 1 }
cLQoSProfileEntry OBJECT-TYPE
SYNTAX CLQoSProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents one of the existing profile types
such as gold, silver, bronze, platinum."
INDEX { cLQoSProfileName }
::= { cLQoSProfileTable 1 }
CLQoSProfileEntry ::= SEQUENCE {
cLQoSProfileName SnmpAdminString,
cLQoSMaximumPriority INTEGER,
cLQoSUnicastDefPriority INTEGER,
cLQoSMulticastDefPriority INTEGER,
cLQoSClientDSAverageDataRate Unsigned32,
cLQoSClientUSAverageDataRate Unsigned32,
cLQoSClientDSBurstDataRate Unsigned32,
cLQoSClientUSBurstDataRate Unsigned32,
cLQoSClientDSAvgRealTimeDataRate Unsigned32,
cLQoSClientUSAvgRealTimeDataRate Unsigned32,
cLQoSClientDSBurstRealTimeDataRate Unsigned32,
cLQoSClientUSBurstRealTimeDataRate Unsigned32,
cLQoSSsidDSAverageDataRate Unsigned32,
cLQoSSsidUSAverageDataRate Unsigned32,
cLQoSSsidDSBurstDataRate Unsigned32,
cLQoSSsidUSBurstDataRate Unsigned32,
cLQoSSsidDSAvgRealTimeDataRate Unsigned32,
cLQoSSsidUSAvgRealTimeDataRate Unsigned32,
cLQoSSsidDSBurstRealTimeDataRate Unsigned32,
cLQoSSsidUSBurstRealTimeDataRate Unsigned32,
cLQoSWlanDSAverageDataRate Unsigned32,
cLQoSWlanUSAverageDataRate Unsigned32,
cLQoSWlanDSBurstDataRate Unsigned32,
cLQoSWlanUSBurstDataRate Unsigned32,
cLQoSWlanDSAvgRealTimeDataRate Unsigned32,
cLQoSWlanUSAvgRealTimeDataRate Unsigned32,
cLQoSWlanDSBurstRealTimeDataRate Unsigned32,
cLQoSWlanUSBurstRealTimeDataRate Unsigned32
}
cLQoSProfileName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the name of the profile, unique
identifier for the profile."
::= { cLQoSProfileEntry 1 }
cLQoSMaximumPriority OBJECT-TYPE
SYNTAX INTEGER {
besteffort(1),
background(2),
video(3),
voice(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the maximum QoS priority of the
WLAN associated with this profile.
besteffort(1) - This indicates that packets for this client
will be sent at besteffort.
background(2) - This indicates that packets for this client
will be sent at lowest priority.
video(3) - This indicates that packets for this client will
be sent at video priority.
voice(4) - This indicates that packets for this client will
be sent at voice priority."
::= { cLQoSProfileEntry 2 }
cLQoSUnicastDefPriority OBJECT-TYPE
SYNTAX INTEGER {
besteffort(1),
background(2),
video(3),
voice(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the unicast default QoS priority of
the WLAN associated with this profile.
besteffort(1) - This indicates that packets for this client
will be sent at besteffort.
background(2) - This indicates that packets for this client
will be sent at lowest priority.
video(3) - This indicates that packets for this client will
be sent at video priority.
voice(4) - This indicates that packets for this client will
be sent at voice priority."
::= { cLQoSProfileEntry 3 }
cLQoSMulticastDefPriority OBJECT-TYPE
SYNTAX INTEGER {
besteffort(1),
background(2),
video(3),
voice(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the multicast default QoS priority
of the WLAN associated with this profile.
besteffort(1) - This indicates that packets for this client
will be sent at besteffort.
background(2) - This indicates that packets for this client
will be sent at lowest priority.
video(3) - This indicates that packets for this client will
be sent at video priority.
voice(4) - This indicates that packets for this client will
be sent at voice priority."
::= { cLQoSProfileEntry 4 }
cLQoSClientDSAverageDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average data rate per user on
downstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 5 }
cLQoSClientUSAverageDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average data rate per user on
upstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 6 }
cLQoSClientDSBurstDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst data rate per user on
downstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 7 }
cLQoSClientUSBurstDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst data rate per user on upstream.
Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 8 }
cLQoSClientDSAvgRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average real time data rate per user
on downstream. Value of 0 indicates the feature is
disabled."
::= { cLQoSProfileEntry 9 }
cLQoSClientUSAvgRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average real time data rate per user
on upstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 10 }
cLQoSClientDSBurstRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst real time data rate per user on
downstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 11 }
cLQoSClientUSBurstRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst real time data rate per user on
upstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 12 }
cLQoSSsidDSAverageDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average data rate per ssid on
downstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 13 }
cLQoSSsidUSAverageDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average data rate per ssid on
upstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 14 }
cLQoSSsidDSBurstDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst data rate per ssid on
downstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 15 }
cLQoSSsidUSBurstDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst data rate per ssid on upstream.
Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 16 }
cLQoSSsidDSAvgRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average real time data rate per ssid
on downstream. Value of 0 indicates the feature is
disabled."
::= { cLQoSProfileEntry 17 }
cLQoSSsidUSAvgRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average real time data rate per ssid
on upstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 18 }
cLQoSSsidDSBurstRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst real time data rate per ssid on
downstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 19 }
cLQoSSsidUSBurstRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst real time data rate per ssid on
upstream. Value of 0 indicates the feature is disabled."
::= { cLQoSProfileEntry 20 }
cLQoSWlanDSAverageDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average data rate per wlan on downstream.
Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 21 }
cLQoSWlanUSAverageDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average data rate per wlan on upstream.
Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 22 }
cLQoSWlanDSBurstDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst data rate per wlan on downstream.
Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 23 }
cLQoSWlanUSBurstDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst data rate per wlan on upstream.
Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 24 }
cLQoSWlanDSAvgRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average real time data rate per wlan on
downstream. Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 25 }
cLQoSWlanUSAvgRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies average real time data rate per wlan on
upstream. Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 26 }
cLQoSWlanDSBurstRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst real time data rate per wlan on
downstream. Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 27 }
cLQoSWlanUSBurstRealTimeDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies burst real time data rate per wlan on
upstream. Value of 0 indicates that feature is disabled."
::= { cLQoSProfileEntry 28 }
-- *******************************************************************
-- * SIP Snooping configuration
-- *******************************************************************
cLQoSSipSnoopingPortRangeStart OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the starting port with respect to SIP
snooping feature on controller. If single port has to be
used, configure cLQoSSipSnoopingPortRangeStart and
cLQoSSipSnoopingPortRangeEnd with same value."
::= { cLQoSSipSnoopingConfig 1 }
cLQoSSipSnoopingPortRangeEnd OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the ending port with respect to SIP
snooping feature on controller. If single port has to be
used, configure cLQoSSipSnoopingPortRangeStart and
cLQoSSipSnoopingPortRangeEnd with same value."
::= { cLQoSSipSnoopingConfig 2 }
-- *******************************************************************
-- * ATF(Air Time Fairness) configuration
-- *******************************************************************
cLQoSGlobalAirTimeFairnessTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSGlobalAirTimeFairnessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the global dot11
parameters per slot id, represented by cLApDot11IfSlotId,
of the radio interface in all the ATF supported APs joined
with the controller."
::= { cLQoSAirTimeFairness 1 }
cLQoSGlobalAirTimeFairnessEntry OBJECT-TYPE
SYNTAX CLQoSGlobalAirTimeFairnessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a row in
cLQoSGlobalAirTimeFairnessTable."
INDEX { cLApDot11IfType }
::= { cLQoSGlobalAirTimeFairnessTable 1 }
CLQoSGlobalAirTimeFairnessEntry ::= SEQUENCE {
cLGlobalAirTimeFairnessMode INTEGER,
cLGlobalAirTimeFairnessOptimizationPolicy TruthValue
}
cLGlobalAirTimeFairnessMode OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
ssid(2),
monitor(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the mode of fairness represented
by cLApDot11IfType of ATF supported APs, joined to the
controller.
disabled(1) - This indicates that fairness mode is
disabled.
SSID Mode(2) - This indicates that fairness mode is SSID
mode.
Monitor Mode(3) - This indicates that fairness mode is
monitor mode.
Read operation on this attribute may differ if config is
overridden."
DEFVAL { 1 }
::= { cLQoSGlobalAirTimeFairnessEntry 1 }
cLGlobalAirTimeFairnessOptimizationPolicy OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the optimization policy
represented by cLApDot11IfType of ATF supported APs, joined
to the controller to be configured. Read operation on this
attribute may differ if config is overridden."
::= { cLQoSGlobalAirTimeFairnessEntry 2 }
cLQoSAirTimeFairnessTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSAirTimeFairnessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the ATF(Air Time Fairness)
configuration per-AP per-SlotId & ATF supported APs that
join with this controller."
::= { cLQoSAirTimeFairness 2 }
cLQoSAirTimeFairnessEntry OBJECT-TYPE
SYNTAX CLQoSAirTimeFairnessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents information of
per-AP, per-SlotId & ATF supported APs information."
INDEX {
cLApSysMacAddress,
cLApDot11IfSlotId
}
::= { cLQoSAirTimeFairnessTable 1 }
CLQoSAirTimeFairnessEntry ::= SEQUENCE {
cLApAirTimeFairnessMode INTEGER,
cLApAirTimeFairnessOptimizationPolicy TruthValue
}
cLApAirTimeFairnessMode OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
ssid(2),
monitor(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the fairness mode of all the ATF
supported access points.
disabled(1) - This object indicates that fairness mode of
all the ATF supported APs is disabled.
SSID Mode(2) - This object indicates that fairness mode of
all the ATF supported APs is SSID mode.
Monitor Mode(3) - This object indicates that fairness mode
of all the ATF supported APs is SSID
mode."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessEntry 1 }
cLApAirTimeFairnessOptimizationPolicy OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies whether stealingpolicy of all the ATF
supported access points should be enabled or disabled.
A value of 'true' indicates that the stealingpolicy of all
the ATF supported access points will be enabled.
A value of 'false' indicates that the stealingpolicy of all
the ATF supported access points will be disabled."
::= { cLQoSAirTimeFairnessEntry 2 }
-- ********************************************************************
-- * ATF(Air Time Fairness) Statistics for Air Time TimeSlice
-- *******************************************************************
cLQoSAirTimeFairnessWlanStatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSAirTimeFairnessWlanStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the ATF(Air Time Fairness) WLAN
statistics for each airtime timeslice per-AP per-SlotId
per-WLANId of ATF supported APs joined to controller."
::= { cLQoSAirTimeFairness 3 }
cLQoSAirTimeFairnessWlanStatisticsEntry OBJECT-TYPE
SYNTAX CLQoSAirTimeFairnessWlanStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents AirTimeFairness timeslice WLAN
statistics."
INDEX {
cLApSysMacAddress,
cLApDot11IfSlotId,
cLWlanProfileName
}
::= { cLQoSAirTimeFairnessWlanStatisticsTable 1 }
CLQoSAirTimeFairnessWlanStatisticsEntry ::= SEQUENCE {
cLApAirTimeFairnessWlanAirtimeUsedInstantaneous TimeInterval,
cLApAirTimeFairnessWlanAirtimeUsedCumulative Unsigned64,
cLApAirTimeFairnessWlanBytesSentInstantaneous Unsigned32,
cLApAirTimeFairnessWlanBytesSentCumulative Unsigned64,
cLApAirTimeFairnessWlanBytesDroppedInstantaneous Unsigned32,
cLApAirTimeFairnessWlanBytesDroppedCumulative Unsigned64,
cLApAirTimeFairnessWlanFramesSentInstantaneous Unsigned32,
cLApAirTimeFairnessWlanFramesSentCumulative Unsigned64,
cLApAirTimeFairnessWlanFramesDroppedInstantaneous Unsigned32,
cLApAirTimeFairnessWlanFramesDroppedCumulative Unsigned64
}
cLApAirTimeFairnessWlanAirtimeUsedInstantaneous OBJECT-TYPE
SYNTAX TimeInterval
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the air time used instantaneous for
particular AP per slot per WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 1 }
cLApAirTimeFairnessWlanAirtimeUsedCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total cumulative AirTime used
for particular AP per slot per WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 2 }
cLApAirTimeFairnessWlanBytesSentInstantaneous OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the number of bytes sent
instantaneously for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 3 }
cLApAirTimeFairnessWlanBytesSentCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of bytes sent
cumulatively for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 4 }
cLApAirTimeFairnessWlanBytesDroppedInstantaneous OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of bytes dropped
instantaneously for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 5 }
cLApAirTimeFairnessWlanBytesDroppedCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of bytes dropped
cumulatively for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 6 }
cLApAirTimeFairnessWlanFramesSentInstantaneous OBJECT-TYPE
SYNTAX Unsigned32
UNITS "pkts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of packets sent
instantaneously for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 7 }
cLApAirTimeFairnessWlanFramesSentCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "pkts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of packets sent
cumulatively for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 8 }
cLApAirTimeFairnessWlanFramesDroppedInstantaneous OBJECT-TYPE
SYNTAX Unsigned32
UNITS "pkts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of packets dropped
instantaneously for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 9 }
cLApAirTimeFairnessWlanFramesDroppedCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "pkts"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of packets dropped
cumulatively for particular AP per slot per
WlanProfileName."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessWlanStatisticsEntry 10 }
cLQoSAirTimeFairnessStatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSAirTimeFairnessStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the ATF(Air Time Fairness) WLAN
statistics for each airtime timeslice per-AP per-slotId of
ATF supported APs joined to controller."
::= { cLQoSAirTimeFairness 4 }
cLQoSAirTimeFairnessStatisticsEntry OBJECT-TYPE
SYNTAX CLQoSAirTimeFairnessStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents AirTimeFairness timeslice statistics."
INDEX {
cLApSysMacAddress,
cLApDot11IfSlotId
}
::= { cLQoSAirTimeFairnessStatisticsTable 1 }
CLQoSAirTimeFairnessStatisticsEntry ::= SEQUENCE {
cLApAirTimeFairnessTotalAirtimeUsedInstantaneous TimeInterval,
cLApAirTimeFairnessTotalAirtimeUsedCumulative Unsigned64,
cLApAirTimeFairnessRadioUptime TimeInterval,
cLApAirTimeFairnessRadioUptimeCumulative TimeInterval
}
cLApAirTimeFairnessTotalAirtimeUsedInstantaneous OBJECT-TYPE
SYNTAX TimeInterval
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the air time used instantaneous for
particular AP per slot."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessStatisticsEntry 1 }
cLApAirTimeFairnessTotalAirtimeUsedCumulative OBJECT-TYPE
SYNTAX Unsigned64
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total AirTime used cumulatively
for particular AP per slot."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessStatisticsEntry 2 }
cLApAirTimeFairnessRadioUptime OBJECT-TYPE
SYNTAX TimeInterval
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the air time used instantaneously
for particular AP per slot."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessStatisticsEntry 3 }
cLApAirTimeFairnessRadioUptimeCumulative OBJECT-TYPE
SYNTAX TimeInterval
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total cumulative radio up time
for particular AP per slot."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessStatisticsEntry 4 }
cLAPGroupAirTimeFairnessTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLAPGroupAirTimeFairnessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the parameters for configuring the
ATF(Air Time Fairness) for AP group."
::= { cLQoSAirTimeFairness 5 }
cLAPGroupAirTimeFairnessEntry OBJECT-TYPE
SYNTAX CLAPGroupAirTimeFairnessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the parameters in
cLAPGroupAirTimeFairnessTable for configuring
ATF(Air Time Fairness) for an AP group."
INDEX {
cLApDot11IfType,
cLAPGroupName
}
::= { cLAPGroupAirTimeFairnessTable 1 }
CLAPGroupAirTimeFairnessEntry ::= SEQUENCE {
cLAPGroupAirTimeFairnessMode INTEGER,
cLAPGroupAirTimeFairnessOptimizationPolicy TruthValue
}
cLAPGroupAirTimeFairnessMode OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
ssid(2),
monitor(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the ATF(Air Time Fairness) mode for
this AP group per radiotype.
disabled(1) - This indicates that the ATF mode for this AP
group is disabled.
ssis(2) - This indicates that the ATF mode for this AP
group is SSID mode.
monitor(3) - This indicates that the ATF mode for this AP
group is monitor mode."
DEFVAL { 0 }
::= { cLAPGroupAirTimeFairnessEntry 1 }
cLAPGroupAirTimeFairnessOptimizationPolicy OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the ATF(Air Time Fairness)
stealingpolicy for this AP group per radio type."
::= { cLAPGroupAirTimeFairnessEntry 2 }
-- ********************************************************************
-- AirTime Fairness Policy Configuration
-- ********************************************************************
cLQosAirTimeFairnessPolicyConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQosAirTimeFairnessPolicyConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains AirTimeFairness policy
configuration sent by the controller to the LWAPP APs for
their operation. This table doesn't have any dependencies
on other existing tables.By defining
cLAirTimeFairnessPolicyid, the unique identifier for a
policy configuration rows are added or deleted by explicit
management actions initiated by the user from a network
management station through the
cLAirTimeFairnessPolicyRowStatus object."
::= { cLQoSAirTimeFairness 6 }
cLQosAirTimeFairnessPolicyConfigEntry OBJECT-TYPE
SYNTAX CLQosAirTimeFairnessPolicyConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents the policy
configuration sent by the controller to LWAPP APs
for use during their operations. Entries can be
added/deleted by explicit management actions by
NMS or by user console."
INDEX { cLAirTimeFairnessPolicyId }
::= { cLQosAirTimeFairnessPolicyConfigTable 1 }
CLQosAirTimeFairnessPolicyConfigEntry ::= SEQUENCE {
cLAirTimeFairnessPolicyId INTEGER,
cLAirTimeFairnessPolicyRowStatus RowStatus,
cLAirTimeFairnessPolicyName SnmpAdminString,
cLAirTimeFairnessPolicyWeight Unsigned32,
cLAirTimeFairnessPolicyclientfairsharing INTEGER
}
cLAirTimeFairnessPolicyId OBJECT-TYPE
SYNTAX INTEGER (0..511)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents uniquely one instance of
a policy id on the controller."
::= { cLQosAirTimeFairnessPolicyConfigEntry 1 }
cLAirTimeFairnessPolicyRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the status column for this row and used
to create, modify and delete specific instances of rows
in this table.
This table supports modification of writable objects when
the RowStatus is 'active'.
The following objects are mandatory for successful
creation of an entry:
cLAirTimeFairnessPolicyName
cLAirTimeFairnessPolicyWeight."
::= { cLQosAirTimeFairnessPolicyConfigEntry 2 }
cLAirTimeFairnessPolicyName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the profile name assigned
to this policy. The name assigned to a policy has to be
unique across all the policies on the controller.
This object cannot be modified when cLWlanRowStatus
is 'active'."
::= { cLQosAirTimeFairnessPolicyConfigEntry 3 }
cLAirTimeFairnessPolicyWeight OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the policy weight assigned to
this policy id/policy name.
PolicyId=0 is default policy ID with weight 10.
We will not be able to configure/modify/delete this policy.
This object cannot be modified when cLWlanRowStatus is
'active'."
::= { cLQosAirTimeFairnessPolicyConfigEntry 4 }
cLAirTimeFairnessPolicyclientfairsharing OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
enabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies whether the client fair sharing is
enabled or disabled for a policy present.
1 - Disabled
2 - Enabled."
DEFVAL { 0 }
::= { cLQosAirTimeFairnessPolicyConfigEntry 5 }
cLApAirTimeFairnessPolicyOverrideTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLApAirTimeFairnessPolicyOverrideTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains per-AP, per-Radio, per-WlanId
override of ATF policy ID on WLAN."
::= { cLQoSAirTimeFairness 7 }
cLApAirTimeFairnessPolicyOverrideEntry OBJECT-TYPE
SYNTAX CLApAirTimeFairnessPolicyOverrideTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents AirTime fairness policy Id override
on WLAN."
INDEX {
cLApSysMacAddress,
cLApDot11IfSlotId,
cLWlanProfileName
}
::= { cLApAirTimeFairnessPolicyOverrideTable 1 }
CLApAirTimeFairnessPolicyOverrideTableEntry ::= SEQUENCE {
cLApAirTimeFairnessPolicyOverride TruthValue,
cLApAirTimeFairnessOverridePolicyName SnmpAdminString
}
cLApAirTimeFairnessPolicyOverride OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies Air time fairness policy override
per AP(ATF supported APs) per Radio per WlanProfileName
for policy Id assigned to WLAN."
::= { cLApAirTimeFairnessPolicyOverrideEntry 1 }
cLApAirTimeFairnessOverridePolicyName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the policy name changed for the given
WLAN, if cLApAirTimeFairnessPolicyOverride is enabled per
AP per slot per wlan profilename. Please note that this
will not change the global policy name on the WLAN on the
WLC in the VAP."
::= { cLApAirTimeFairnessPolicyOverrideEntry 2 }
cLAPGroupsAirTimeFairnessPolicyOverrideTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLAPGroupsAirTimeFairnessPolicyOverrideEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains per-APGroup, per-WlanId override of
ATF policy ID on WLAN."
::= { cLQoSAirTimeFairness 8 }
cLAPGroupsAirTimeFairnessPolicyOverrideEntry OBJECT-TYPE
SYNTAX CLAPGroupsAirTimeFairnessPolicyOverrideEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents AirTime fairness policy name
overrride on APGroup per cLWlanProfileName."
INDEX {
cLApDot11IfType,
cLAPGroupName,
cLWlanProfileName
}
::= { cLAPGroupsAirTimeFairnessPolicyOverrideTable 1 }
CLAPGroupsAirTimeFairnessPolicyOverrideEntry ::= SEQUENCE {
cLAPGroupAirTimeFairnessPolicyNameOverrideEnabled TruthValue,
cLAPGroupAirTimeFairnessOverridePolicyName SnmpAdminString
}
cLAPGroupAirTimeFairnessPolicyNameOverrideEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the per APGroup per WLAN profile name
level policy override parameters.
A value of 'true' indicates that user can override the
global policy name by providing individual new
cLApAirTimeFairnessOverridePolicyName per APGroup per WLAN
profile name level.
A value of 'false' indicates that the
cLAPGroupAirTimeFairnessOverridePolicyName will be
configured with global policy name assigned at WlanId
level."
DEFVAL { false }
::= { cLAPGroupsAirTimeFairnessPolicyOverrideEntry 1 }
cLAPGroupAirTimeFairnessOverridePolicyName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the policy name changed for the
given WLAN, if
cLAPGroupAirTimeFairnessPolicyNameOverrideEnabled is
enabled per AP Group. Please note that this will not change
the global policy name on the WLAN on the WLC in the VAP."
::= { cLAPGroupsAirTimeFairnessPolicyOverrideEntry 2 }
-- ********************************************************************
-- *AirTime Fairness Client Metrics
-- ********************************************************************
cLQoSAirTimeFairnessClientStatisticsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSAirTimeFairnessClientStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the ATF(Air Time Fairness) client
statistics for each airtime timeslice per-AP per-SlotId
per-WlanId of ATF supported APs joined to controller."
::= { cLQoSAirTimeFairness 9 }
cLQoSAirTimeFairnessClientStatisticsEntry OBJECT-TYPE
SYNTAX CLQoSAirTimeFairnessClientStatisticsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents AirTimeFairness timeslice client
statistics."
INDEX {
cLApSysMacAddress,
cLApDot11IfSlotId,
cLWlanProfileName,
cldcClientMacAddress
}
::= { cLQoSAirTimeFairnessClientStatisticsTable 1 }
CLQoSAirTimeFairnessClientStatisticsEntry ::= SEQUENCE {
cLApAirTimeFairnessClientAirtimeUsedInstantaneous TimeInterval,
cLApAirTimeFairnessClientAirtimeUsedCumulative Unsigned32,
cLApAirTimeFairnessClientFramesSent Unsigned32,
cLApAirTimeFairnessClientFramesDropped Unsigned32,
cLApAirTimeFairnessClientUsage INTEGER
}
cLApAirTimeFairnessClientAirtimeUsedInstantaneous OBJECT-TYPE
SYNTAX TimeInterval
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the air time used instantaneous
for particular AP per slot per WLAN clients."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessClientStatisticsEntry 1 }
cLApAirTimeFairnessClientAirtimeUsedCumulative OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total AirTime used cumulative
for particular AP per slot per WLAN clients."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessClientStatisticsEntry 2 }
cLApAirTimeFairnessClientFramesSent OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the number of frames sent
instantaneously for particular AP per slot per WLAN
clients."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessClientStatisticsEntry 3 }
cLApAirTimeFairnessClientFramesDropped OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the total number of frames dropped
cumulatively for particular AP per slot per WLAN clients."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessClientStatisticsEntry 4 }
cLApAirTimeFairnessClientUsage OBJECT-TYPE
SYNTAX INTEGER {
none(1),
lowusage(2),
regusage(3),
overusage(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the client usage for particular AP
per slot per WLAN clients.
none(1) - This indicates that client usage for particular
AP per slot per clients is unknown.
lowusage(2) - This indicates that client usage for
particular AP per slot per clients is low.
regusage(3) - This indicates that client usage for
particular AP per slot per clients is
regular.
overusage(4) - This indicates that client usage for
particular AP per slot per clients is high."
DEFVAL { 0 }
::= { cLQoSAirTimeFairnessClientStatisticsEntry 5 }
-- ********************************************************************
-- * NOTIFICATION Control objects
-- ********************************************************************
ciscoLwappVoipCallFailureNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object specifies the status of the generation of
ciscoLwappVoipCallFailureNotif notification.
A value of 'true' indicates that the agent generates
ciscoLwappVoipCallFailureNotif notification.
A value of 'false' indicates that the agent doesn't
generate ciscoLwappVoipCallFailureNotif notification."
::= { cLQConfigObjects 1 }
ciscoLwappKtsVoipCallFailureNotifEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object to control the generation of
ciscoLwappKtsVoipCallFailureNotif notification.
A value of 'true' indicates that the agent generates
ciscoLwappKtsVoipCallFailureNotif notification.
A value of 'false' indicates that the agent doesn't
generate ciscoLwappKtsVoipCallFailureNotif notification."
::= { cLQConfigObjects 2 }
cLQosMapStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the status of QoS Map.
A value of 'true' indicates that QoS map is enabled.
A value of 'false' indicates that QoS map is disabled."
::= { cLQoSMapConfig 1 }
cLQoSMapUpRangesTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSUpTableEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table contains the UP Ranges. There can be 8 rows,
1 for each UP. Each row contains a DSCP low to high
for that UP."
::= { cLQoSMapConfig 2 }
cLQoSUpTableEntry OBJECT-TYPE
SYNTAX CLQoSUpTableEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Each entry represents the rows from 0-7 containing DSCP
low to high."
INDEX { cLQoSUpTableIndex }
::= { cLQoSMapUpRangesTable 1 }
CLQoSUpTableEntry ::= SEQUENCE {
cLQoSUpTableIndex Unsigned32,
cLQoSMapUp Unsigned32,
cLQoSMapDscpDefault Unsigned32,
cLQoSMapDscpLow Unsigned32,
cLQoSMapDscpHigh Unsigned32
}
cLQoSUpTableIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object represents the index for UP To DSCP table.
Range is from 1 to 8."
::= { cLQoSUpTableEntry 1 }
cLQoSMapUp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies the UP value of the entry."
::= { cLQoSUpTableEntry 2 }
cLQoSMapDscpDefault OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies the default DSCP value for the UP."
::= { cLQoSUpTableEntry 3 }
cLQoSMapDscpLow OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies the DSCP low value for the UP."
::= { cLQoSUpTableEntry 4 }
cLQoSMapDscpHigh OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies the DSCP low value for the UP."
::= { cLQoSUpTableEntry 5 }
cLQoSMapUpExceptionsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSUpExceptionsTableEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table contains the QoS map exceptions configured."
::= { cLQoSMapConfig 3 }
cLQoSUpExceptionsTableEntry OBJECT-TYPE
SYNTAX CLQoSUpExceptionsTableEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Each entry represents an exception rule can accomodate
21 rows."
INDEX { cLQoSMapExceptionNumber }
::= { cLQoSMapUpExceptionsTable 1 }
CLQoSUpExceptionsTableEntry ::= SEQUENCE {
cLQoSMapExceptionNumber Unsigned32,
cLQoSMapExceptionUp Unsigned32,
cLQoSMapExceptionDscp Unsigned32,
cLQosMapExceptionsRowStatus RowStatus
}
cLQoSMapExceptionNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object represents the UP value of the entry."
::= { cLQoSUpExceptionsTableEntry 1 }
cLQoSMapExceptionUp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the DSCP low value for the UP."
::= { cLQoSUpExceptionsTableEntry 2 }
cLQoSMapExceptionDscp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the DSCP low value for the UP."
::= { cLQoSUpExceptionsTableEntry 3 }
cLQosMapExceptionsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This is the status column for this row and used
to create and delete specific instances of rows
in this table. Owing objects are mandatory for successful
creation of an entry:
cLQoSMapExceptionUp,cLQoSMapExceptionDscp."
::= { cLQoSUpExceptionsTableEntry 4 }
cLQosCopyClientDscpStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the status of copy client
DSCP(Enabled/Disabled).
A value of 'true' indicates that copy client DSCP is
enabled.
A value of 'false' indicates that copy client DSCP is
disabled."
::= { cLQoSMapConfig 4 }
cLQosMapExceptionsClearAll OBJECT-TYPE
SYNTAX INTEGER {
clear-all(1),
no-operation(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies to clear all exceptions.
clear-all(1) - will clear all the exceptions.
no-operation(2) - no operation will be done."
::= { cLQoSMapConfig 5 }
cLQosMapDefault OBJECT-TYPE
SYNTAX INTEGER {
default(1),
no-operation(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies to set the default values for both
the tables cLQoSMapUpExceptionsTable and
cLQoSMapUpRangesTable.
default(1) - Default values will be set to
cLQoSMapUpExceptionsTable and
cLQoSMapUpRangesTable.
no-operation(2) - No operation will be executed."
::= { cLQoSMapConfig 6 }
-- *******************************************************************
-- QoS Map Tables
-- *******************************************************************
cLQoSMapDownstreamDscpTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSMapDownstreamDscpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the downstream DSCP ranges.
This table has 8 UP entries.
Each entry contains a DSCP lower range to higher range
values for that UP.
The default values of QoS Map Downstream DSCP table is
Start DSCP End DSCP Up
0 7 0
8 15 1
16 23 2
24 31 3
32 39 4
40 47 5
48 55 6
56 63 7
UP is the abbreviation for User Priority."
::= { ciscoLwappQosMIBTableObjects 1 }
cLQoSMapDownstreamDscpEntry OBJECT-TYPE
SYNTAX CLQoSMapDownstreamDscpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents a DSCP lower range to higher range
values for each UP(User Priority)."
INDEX { cLQoSMapDownstreamDscpIndex }
::= { cLQoSMapDownstreamDscpTable 1 }
CLQoSMapDownstreamDscpEntry ::= SEQUENCE {
cLQoSMapDownstreamDscpIndex Unsigned32,
cLQoSMapDownstreamDscpLow Unsigned32,
cLQoSMapDownstreamDscpHigh Unsigned32,
cLQoSMapDownstreamUp Unsigned32
}
cLQoSMapDownstreamDscpIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the index for UP To DSCP Table.
Range is from 1 to 8. The index value should be one number
higher than UP value."
::= { cLQoSMapDownstreamDscpEntry 1 }
cLQoSMapDownstreamDscpLow OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the DSCP lower range value for the
UP."
::= { cLQoSMapDownstreamDscpEntry 2 }
cLQoSMapDownstreamDscpHigh OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the DSCP higher range value for the
UP."
::= { cLQoSMapDownstreamDscpEntry 3 }
cLQoSMapDownstreamUp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the UP(User Priority) value of the
QoS map."
::= { cLQoSMapDownstreamDscpEntry 4 }
cLQoSMapDownstreamUpExceptionsTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSDownstreamUpExceptionsTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the QoS map exceptions configured.
The default values for QoS map downstream exceptions table
are
DSCP UP
0 0
2 1
4 1
6 1
10 2
12 2
14 2
18 3
20 3
22 3
26 4
34 5
46 6
48 7
56 7
UP is the abbreviation for User Priority."
::= { ciscoLwappQosMIBTableObjects 2 }
cLQoSDownstreamUpExceptionsTableEntry OBJECT-TYPE
SYNTAX CLQoSDownstreamUpExceptionsTableEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents an exception rule is allowed to
contain maximum 21 rows."
INDEX { cLQoSMapDownstreamExceptionNumber }
::= { cLQoSMapDownstreamUpExceptionsTable 1 }
CLQoSDownstreamUpExceptionsTableEntry ::= SEQUENCE {
cLQoSMapDownstreamExceptionNumber Unsigned32,
cLQoSMapDownstreamExceptionDscp Unsigned32,
cLQoSMapDownstreamExceptionUp Unsigned32,
cLQosMapDownstreamExceptionsRowStatus RowStatus
}
cLQoSMapDownstreamExceptionNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the index for the exception table,
that can have max of 21 entries."
::= { cLQoSDownstreamUpExceptionsTableEntry 1 }
cLQoSMapDownstreamExceptionDscp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the DSCP value that need to be
exception value for that UP."
::= { cLQoSDownstreamUpExceptionsTableEntry 2 }
cLQoSMapDownstreamExceptionUp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the UP value of the QoS Map."
::= { cLQoSDownstreamUpExceptionsTableEntry 3 }
cLQosMapDownstreamExceptionsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is the status column for this row and used
to create and delete specific instances of rows
in this table.
Following objects are mandatory for successful
creation of an entry:
Downstream Exception UP, Downstream Exception DSCP."
::= { cLQoSDownstreamUpExceptionsTableEntry 4 }
cLQoSMapUpstreamUpDscpTable OBJECT-TYPE
SYNTAX SEQUENCE OF CLQoSMapUpstreamUpDscpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the Upstream UP to DSCP.
There can be 8 rows, 1 for each UP.
The default values of QoS Map Upstream DSCP table are:
DSCP Up
0 0
2 1
10 2
18 3
26 4
34 5
46 6
48 7
UP is the abbreviation for User Priority."
::= { ciscoLwappQosMIBTableObjects 3 }
cLQoSMapUpstreamUpDscpEntry OBJECT-TYPE
SYNTAX CLQoSMapUpstreamUpDscpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry represents rows from DSCP for each of the UP
0 to 7."
INDEX { cLQoSMapUpstreamDscpIndex }
::= { cLQoSMapUpstreamUpDscpTable 1 }
CLQoSMapUpstreamUpDscpEntry ::= SEQUENCE {
cLQoSMapUpstreamDscpIndex Unsigned32,
cLQoSMapUpstreamUp Unsigned32,
cLQoSMapUpstreamDscp Unsigned32
}
cLQoSMapUpstreamDscpIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the index for UP To DSCP upstream
table. Range is from 1 to 8. The index value should be one
number higher than UP value."
::= { cLQoSMapUpstreamUpDscpEntry 1 }
cLQoSMapUpstreamUp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the UP value of the QoS map."
::= { cLQoSMapUpstreamUpDscpEntry 2 }
cLQoSMapUpstreamDscp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the DSCP value for the UP.
It holds the default value of 255."
::= { cLQoSMapUpstreamUpDscpEntry 3 }
-- *******************************************************************
-- QoS Global Object
-- *******************************************************************
cLQosUpstreamCopyClientDscpStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the status of upstream copy client
DSCP(Enabled/Disabled).
A value of 'true' indicates that upstream copy client
DSCP is enabled.
A value of 'false' indicates that upstream copy client
DSCP is disabled ."
DEFVAL { false }
::= { ciscoLwappQosMIBGlobalObjects 1 }
cLQosFastlaneDisable OBJECT-TYPE
SYNTAX INTEGER {
disable(1),
no-operation(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the default values for all global
QoS fastlane config and disable fastlane feature for all
WLAN.
disable(1) - Fastlane feature for all WLANs will be
disabled.
no-operation(2) - No operation will be performed."
::= { cLQoSFastlaneConfig 1 }
-- ********************************************************************
-- * Notifications
-- ********************************************************************
ciscoLwappVoipCallFailureNotif NOTIFICATION-TYPE
OBJECTS {
cLQVoiceClientLastCallFailureReasonCode,
cLQVoiceClientCallingNumber,
cLQVoiceClientLastCalledNumber,
cLApName,
cLApDot11IfType
}
STATUS current
DESCRIPTION
"This notification is generated when ever a VoIP call failure
occurs."
::= { ciscoLwappQosMIBNotifs 1 }
-- Gayathri
ciscoLwappMediaMCStreamFailureNotif NOTIFICATION-TYPE
OBJECTS {
cldcClientMacAddress,
cLQVMediaClientSrcIpAddr,
cLQVMediaClientSrcIpAddrType,
cLQVMediaClientDestIpAddr,
cLQVMediaClientDestIpAddrType,
cLQVMediaClientHistLastFailureReasonCode,
cLQVMediaClientHistTimeStamp,
cLQMStreamName,
cLApName,
cLApDot11IfType,
cLWlanIndex,
cLQVMediaClientHistCfgBw,
cLQVMediaClientHistCurrentRate,
cLQVMediaClientHistVideoPktSize,
cLQVMediaClientHistVideoUtil,
cLQVMediaClientHistVoiceUtil,
cLQVMediaClientHistChannelUtil,
cLQVMediaClientHistQueueUtil,
cLQVMediaClientHistVideoPps,
cLQVMediaClientHistVideoDelay,
cLQVMediaClientHistPktLossDiscard,
cLQVMediaClientHistPktLossFail,
cLQVMediaClientHistNumVideoStreams,
cLQVMediaClientHistCacEnable
}
STATUS current
DESCRIPTION
"This notification is generated when ever a multicast to
unicast media conversion failure occurs. AP MAC address and
slotID will be sent as index for AP related objects."
::= { ciscoLwappQosMIBNotifs 2 }
ciscoLwappMediaMCStreamAdmitNotif NOTIFICATION-TYPE
OBJECTS {
cldcClientMacAddress,
cLQVMediaClientSrcIpAddr,
cLQVMediaClientSrcIpAddrType,
cLQVMediaClientDestIpAddr,
cLQVMediaClientDestIpAddrType,
cLQVMediaClientHistLastFailureReasonCode,
cLQVMediaClientHistTimeStamp,
cLQMStreamName,
cLApName,
cLApDot11IfType,
cLWlanIndex,
cLQVMediaClientHistCfgBw,
cLQVMediaClientHistCurrentRate,
cLQVMediaClientHistVideoPktSize,
cLQVMediaClientHistVideoUtil,
cLQVMediaClientHistVoiceUtil,
cLQVMediaClientHistChannelUtil,
cLQVMediaClientHistQueueUtil,
cLQVMediaClientHistVideoPps,
cLQVMediaClientHistVideoDelay,
cLQVMediaClientHistPktLossDiscard,
cLQVMediaClientHistPktLossFail,
cLQVMediaClientHistNumVideoStreams,
cLQVMediaClientHistCacEnable
}
STATUS current
DESCRIPTION
"This notification is generated when ever a client gets
admitted to the stream. AP MAC Address and slotID will be
sent as index for AP related objects."
::= { ciscoLwappQosMIBNotifs 3 }
ciscoLwappMediaMCStreamDelistNotif NOTIFICATION-TYPE
OBJECTS {
cldcClientMacAddress,
cLQVMediaClientSrcIpAddr,
cLQVMediaClientSrcIpAddrType,
cLQVMediaClientDestIpAddr,
cLQVMediaClientDestIpAddrType,
cLQVMediaClientHistLastFailureReasonCode,
cLQVMediaClientHistTimeStamp,
cLQMStreamName,
cLApName,
cLApDot11IfType,
cLWlanIndex,
cLQVMediaClientHistCfgBw,
cLQVMediaClientHistCurrentRate,
cLQVMediaClientHistVideoPktSize,
cLQVMediaClientHistVideoUtil,
cLQVMediaClientHistVoiceUtil,
cLQVMediaClientHistChannelUtil,
cLQVMediaClientHistQueueUtil,
cLQVMediaClientHistVideoPps,
cLQVMediaClientHistVideoDelay,
cLQVMediaClientHistPktLossDiscard,
cLQVMediaClientHistPktLossFail,
cLQVMediaClientHistNumVideoStreams,
cLQVMediaClientHistCacEnable
}
STATUS current
DESCRIPTION
"This notification is generated when ever a client delists
from the stream. AP MAC address and slotID will be sent as
index for AP related objects."
::= { ciscoLwappQosMIBNotifs 4 }
ciscoLwappKtsVoipCallFailureNotif NOTIFICATION-TYPE
OBJECTS {
cLQVoiceClientLastCallFailureReasonCode,
cLApName,
cLApDot11IfType
}
STATUS current
DESCRIPTION
"This notification is generated when ever a KTS VoIP call
failure occurs."
::= { ciscoLwappQosMIBNotifs 5 }
-- ********************************************************************
ciscoLwappQosMIBCompliances OBJECT IDENTIFIER
::= { ciscoLwappQosMIBConform 1 }
ciscoLwappQosMIBGroups OBJECT IDENTIFIER
::= { ciscoLwappQosMIBConform 2 }
ciscoLwappQosMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappQosMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappQosDot11aConfigGroup,
ciscoLwappQosDot11bConfigGroup,
ciscoLwappQosDot11WlanConfigGroup,
ciscoLwappQosDot11CacStatsGroup
}
::= { ciscoLwappQosMIBCompliances 1 }
ciscoLwappQosMIBComplianceRev1 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoLwappQosMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappQosDot11aConfigGroup,
ciscoLwappQosDot11bConfigGroup,
ciscoLwappQosDot11WlanConfigGroup,
ciscoLwappQosDot11CacStatsGroup,
ciscoLwappQosDot11aConfigGroupSup1,
ciscoLwappQosDot11bConfigGroupSup1
}
::= { ciscoLwappQosMIBCompliances 2 }
ciscoLwappQosMIBComplianceRev2 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"Implementation of this group is mandatory only for the
platforms which implement the ciscoLwappQosMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappQosDot11aConfigGroup,
ciscoLwappQosDot11bConfigGroup,
ciscoLwappQosDot11WlanConfigGroup,
ciscoLwappQosDot11CacStatsGroup,
ciscoLwappQosDot11aConfigGroupSup1,
ciscoLwappQosDot11bConfigGroupSup1,
ciscoLwappQosDot11aConfigGroupSup2,
ciscoLwappQosDot11bConfigGroupSup2,
ciscoLwappQosDot11SipCacStatsGroup,
ciscoLwappQosDot11SipConfigGroup,
ciscoLwappQosDot11VoiceStatsGroup,
ciscoLwappQosDot11VoiceConfigGroup,
ciscoLwappQosDot11VoiceNotifGroup,
ciscoLwappQosConfigGroup
}
::= { ciscoLwappQosMIBCompliances 3 }
ciscoLwappQosMIBComplianceRev3 MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"Implementation of this group is mandatory only for the
platforms which implement the ciscoLwappQosMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappQosDot11aConfigGroup,
ciscoLwappQosDot11bConfigGroup,
ciscoLwappQosDot11WlanConfigGroup,
ciscoLwappQosDot11CacStatsGroup,
ciscoLwappQosDot11aConfigGroupSup1,
ciscoLwappQosDot11bConfigGroupSup1,
ciscoLwappQosDot11aConfigGroupSup2,
ciscoLwappQosDot11bConfigGroupSup2,
ciscoLwappQosDot11SipCacStatsGroup,
ciscoLwappQosDot11SipConfigGroup,
ciscoLwappQosDot11VoiceStatsGroup,
ciscoLwappQosDot11VoiceConfigGroup,
ciscoLwappQosDot11VoiceNotifGroup,
ciscoLwappQosConfigGroup,
ciscoLwappQosDot11VoiceNotifGroupSup1,
ciscoLwappQosConfigGroupSup1
}
::= { ciscoLwappQosMIBCompliances 4 }
ciscoLwappQosMIBComplianceRev4 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Implementation of this group is mandatory only for the
platforms which implement the ciscoLwappQosMIB module."
MODULE -- this module
MANDATORY-GROUPS {
ciscoLwappQosDot11aConfigGroup,
ciscoLwappQosDot11bConfigGroup,
ciscoLwappQosDot11WlanConfigGroup,
ciscoLwappQosDot11CacStatsGroup,
ciscoLwappQosDot11aConfigGroupSup1,
ciscoLwappQosDot11bConfigGroupSup1,
ciscoLwappQosDot11aConfigGroupSup2,
ciscoLwappQosDot11bConfigGroupSup2,
ciscoLwappQosDot11SipCacStatsGroup,
ciscoLwappQosDot11SipConfigGroup,
ciscoLwappQosDot11VoiceStatsGroup,
ciscoLwappQosDot11VoiceConfigGroup,
ciscoLwappQosDot11VoiceNotifGroup,
ciscoLwappQosConfigGroup,
ciscoLwappQosDot11VoiceNotifGroupSup1,
ciscoLwappQosConfigGroupSup1,
cLQoSProfileGroup
}
::= { ciscoLwappQosMIBCompliances 5 }
-- ********************************************************************
-- * Units of conformance
-- ********************************************************************
ciscoLwappQosDot11aConfigGroup OBJECT-GROUP
OBJECTS {
cLQd11aVoiceAdmCtrlSupport,
cLQd11aVoiceMaxAdmBandwidth,
cLQd11aVoiceMaxRoamBandwidth,
cLQd11aVideoAdmCtrlSupport,
cLQd11aVideoMaxAdmBandwidth,
cLQd11aVideoMaxRoamBandwidth,
cLQd11aGprProbeInterval
}
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service parameters 802.11a networks."
::= { ciscoLwappQosMIBGroups 1 }
ciscoLwappQosDot11bConfigGroup OBJECT-GROUP
OBJECTS {
cLQd11bVoiceAdmCtrlSupport,
cLQd11bVoiceMaxAdmBandwidth,
cLQd11bVoiceMaxRoamBandwidth,
cLQd11bVideoAdmCtrlSupport,
cLQd11bVideoMaxAdmBandwidth,
cLQd11bVideoMaxRoamBandwidth,
cLQd11bGprProbeInterval
}
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service parameters 802.11b networks."
::= { ciscoLwappQosMIBGroups 2 }
ciscoLwappQosDot11WlanConfigGroup OBJECT-GROUP
OBJECTS { cLQd11GprSupport }
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-services parameters on a particular WLAN."
::= { ciscoLwappQosMIBGroups 3 }
ciscoLwappQosDot11CacStatsGroup OBJECT-GROUP
OBJECTS {
cLQd11CacVoiceBwInUse,
cLQd11CacVideoBwInUse,
cLQd11CacVoiceCallsInProgress,
cLQd11CacRoamVoiceCallsInProg,
cLQd11CacTotalVoiceCallsAP,
cLQd11CacTotalRoamCallsAP,
cLQd11CacVoiceCallsRejectedAP,
cLQd11CacRoamCallsRejectedAP,
cLQd11CacRejCallsInsufBw,
cLQd11CacRejCallsBadParams,
cLQd11CacRejCallsPhyRate,
cLQd11CacRejCallsQosPolicy
}
STATUS current
DESCRIPTION
"This collection of objects provide the call
admission control statistics observed on the
dot11 interfaces of an AP."
::= { ciscoLwappQosMIBGroups 4 }
ciscoLwappQosDot11aConfigGroupSup1 OBJECT-GROUP
OBJECTS {
cLQd11aVoiceCtrl,
cLQd11aExpeditedBw
}
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service parameters 802.11a networks."
::= { ciscoLwappQosMIBGroups 5 }
ciscoLwappQosDot11bConfigGroupSup1 OBJECT-GROUP
OBJECTS {
cLQd11bVoiceCtrl,
cLQd11bExpeditedBw
}
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service parameters 802.11b networks."
::= { ciscoLwappQosMIBGroups 6 }
ciscoLwappQosDot11aConfigGroupSup2 OBJECT-GROUP
OBJECTS {
cLQd11aEdcaProfile,
cLQd11aMacOptimization,
cLQd11aMaxCallLimit
}
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service parameters 802.11a networks."
::= { ciscoLwappQosMIBGroups 7 }
ciscoLwappQosDot11bConfigGroupSup2 OBJECT-GROUP
OBJECTS {
cLQd11bEdcaProfile,
cLQd11bMacOptimization,
cLQd11bMaxCallLimit
}
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service parameters 802.11b networks."
::= { ciscoLwappQosMIBGroups 8 }
ciscoLwappQosDot11SipCacStatsGroup OBJECT-GROUP
OBJECTS {
cLQd11SipCacNonRoamCallsInProgress,
cLQd11SipCacRoamCallsInProg,
cLQd11SipCacTotalNonRoamCallsAP,
cLQd11SipCacTotalRoamCallsAP,
cLQd11SipCacNonRoamCallsRejectedInSuffBw,
cLQd11SipCacRoamCallsRejectedInSuffBw,
cLQd11SipCacNonRoamCallsRejectedMaxLimit,
cLQd11SipCacRoamCallsRejectedMaxLimit,
cLQd11SipCacRejCallsQosPolicy
}
STATUS current
DESCRIPTION
"This collection of objects provide the SIP call
admission control statistics observed on the
dot11 interfaces of an AP."
::= { ciscoLwappQosMIBGroups 9 }
ciscoLwappQosDot11SipConfigGroup OBJECT-GROUP
OBJECTS {
cLQd11SipCacConfigCodecType,
cLQd11SipCacConfigBw,
cLQd11SipCacConfigVoiceSampleSize
}
STATUS current
DESCRIPTION
"This collection of objects represents the
SIP call admission control configuration parameters."
::= { ciscoLwappQosMIBGroups 10 }
ciscoLwappQosDot11VoiceStatsGroup OBJECT-GROUP
OBJECTS {
cLQd11VoiceCallCounts,
cLQd11CacVoiceCallTimePeriod
}
STATUS current
DESCRIPTION
"This collection of objects represents the
voice statistics parameters."
::= { ciscoLwappQosMIBGroups 11 }
ciscoLwappQosDot11VoiceConfigGroup OBJECT-GROUP
OBJECTS {
cLQVoiceWlanConfigDetectVoipCallFailure,
cLQVoiceClientCallingNumber,
cLQVoiceClientLastCalledNumber,
cLQVoiceClientLastCallFailureReasonCode
}
STATUS current
DESCRIPTION
"This collection of objects represents the
voice statistics parameters."
::= { ciscoLwappQosMIBGroups 12 }
ciscoLwappQosDot11VoiceNotifGroup NOTIFICATION-GROUP
NOTIFICATIONS { ciscoLwappVoipCallFailureNotif }
STATUS current
DESCRIPTION
"This collection of objects represents the
voice notification parameters."
::= { ciscoLwappQosMIBGroups 13 }
ciscoLwappQosConfigGroup OBJECT-GROUP
OBJECTS { ciscoLwappVoipCallFailureNotifEnabled }
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service configuration parameters."
::= { ciscoLwappQosMIBGroups 14 }
ciscoLwappQosDot11VoiceNotifGroupSup1 NOTIFICATION-GROUP
NOTIFICATIONS { ciscoLwappKtsVoipCallFailureNotif }
STATUS current
DESCRIPTION
"This collection of objects represents the
voice notification parameters."
::= { ciscoLwappQosMIBGroups 15 }
ciscoLwappQosConfigGroupSup1 OBJECT-GROUP
OBJECTS { ciscoLwappKtsVoipCallFailureNotifEnabled }
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service configuration parameters."
::= { ciscoLwappQosMIBGroups 16 }
cLQoSProfileGroup OBJECT-GROUP
OBJECTS {
cLQoSMaximumPriority,
cLQoSUnicastDefPriority,
cLQoSMulticastDefPriority,
cLQoSClientDSAverageDataRate,
cLQoSClientUSAverageDataRate,
cLQoSClientDSBurstDataRate,
cLQoSClientUSBurstDataRate,
cLQoSClientDSAvgRealTimeDataRate,
cLQoSClientUSAvgRealTimeDataRate,
cLQoSClientDSBurstRealTimeDataRate,
cLQoSClientUSBurstRealTimeDataRate,
cLQoSSsidDSAverageDataRate,
cLQoSSsidUSAverageDataRate,
cLQoSSsidDSBurstDataRate,
cLQoSSsidUSBurstDataRate,
cLQoSSsidDSAvgRealTimeDataRate,
cLQoSSsidUSAvgRealTimeDataRate,
cLQoSSsidDSBurstRealTimeDataRate,
cLQoSSsidUSBurstRealTimeDataRate,
cLQoSWlanDSAverageDataRate,
cLQoSWlanUSAverageDataRate,
cLQoSWlanDSBurstDataRate,
cLQoSWlanUSBurstDataRate,
cLQoSWlanDSAvgRealTimeDataRate,
cLQoSWlanUSAvgRealTimeDataRate,
cLQoSWlanDSBurstRealTimeDataRate,
cLQoSWlanUSBurstRealTimeDataRate
}
STATUS current
DESCRIPTION
"This collection of objects represents the
quality-of-service profile parameters."
::= { ciscoLwappQosMIBGroups 17 }
END
View Git Blame Copy Permalink