-- -- QTECH-IPSEC2-MIB.mib -- MIB generated by MG-SOFT Visual MIB Builder Version 6.0 Build 88 -- Tuesday, February 14, 2012 at 13:07:15 -- QTECH-IPSEC2-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP FROM SNMPv2-CONF IpAddress, Integer32, Unsigned32, Gauge32, Counter32, Counter64, OBJECT-TYPE, NOTIFICATION-TYPE FROM SNMPv2-SMI DisplayString, TimeStamp, TEXTUAL-CONVENTION FROM SNMPv2-TC qtechMgmt FROM QTECH-SMI; qtechIPSec2MibModule MODULE-IDENTITY LAST-UPDATED "201112191637Z" -- December 19, 2011 at 16:37 GMT ORGANIZATION "Organization." CONTACT-INFO "Contact-info." DESCRIPTION "Description." ::= { qtechMgmt 108 } -- -- Textual conventions -- QtechIPSecNegoType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of key used by an IPSec Phase-2 Tunnel. invalidType(2147483647) is defined as invalid value." SYNTAX INTEGER { ike(1), manual(2), invalidType(2147483647) } QtechEncapMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The encapsulation mode used by an IPSec Phase-2 Tunnel." SYNTAX INTEGER { tunnel(1), transport(2), invalidMode(2147483647) } QtechEncryptAlgo ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The encryption algorithm used in the IKE and IPSec negotiations. invalidAlg(2147483647) is defined as invalid value." SYNTAX INTEGER { none(0), desCbc(2), threedesCbc(3), aesCbc(12), sm1Cbc(128), invalidAlg(2147483647) } QtechAuthAlgo ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The authentication algorithm used in the IKE negotiations. invalidAlg(2147483647) is defined as invalid value." SYNTAX INTEGER { none(0), md5(2), sha(3), invalidAlg(2147483647) } QtechDiffHellmanGrp ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Diffie Hellman Group used in the IKE and IPSec negotiations. invalidAlg(2147483647) is defined as invalid value." SYNTAX INTEGER { modp768(1), modp1024(2), invalidMode(2147483647) } QtechIPSecTunnelState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The state of IPSec tunnel." SYNTAX INTEGER { establishing(1), active(2), expiring(3) } QtechSaProtocol ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The protocol of security association." SYNTAX INTEGER { reserved(0), isakmp(1), ah(2), esp(3) } QtechTrafficType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of the data flow." SYNTAX INTEGER { ipv4Addr(1), ipv4AddrSubnet(2), ipv6Addr(3), ipv6AddrSubnet(4), ipv4AddrRange(5), ipv6AddrRange(6) } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1 -- December 19, 2011 at 16:37 GMT -- -- Textual conventions -- QtechIPSec2NegoType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of key used by an IPSec Phase-2 Tunnel. invalidType(2147483647) is defined as invalid value." SYNTAX INTEGER { ike(1), manual(2), invalidType(2147483647) } QtechIPSec2TunnelState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The state of IPSec tunnel." SYNTAX INTEGER { establishing(1), active(2), expiring(3) } -- -- Node definitions -- -- 1.3.6.1.4.1.27514.1.1.10.2.108.1 qtechIPSec2Objects OBJECT IDENTIFIER ::= { qtechIPSec2MibModule 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1 qtechIPSec2TunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechIPSec2TunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IPSec Phase-2 Tunnel Table. There is one entry in this table for each active IPSec Phase-2 Tunnel." ::= { qtechIPSec2Objects 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1 qtechIPSec2TunnelEntry OBJECT-TYPE SYNTAX QtechIPSec2TunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about QtechIPSec2TunnelTable." INDEX { qtechIPSec2TunIfIndex, qtechIPSec2TunRemoteAddr, qtechIPSec2TrafficLocalType, qtechIPSec2TrafficLocalProtocol, qtechIPSec2TrafficLocalAddr1, qtechIPSec2TrafficLocalAddr2, qtechIPSec2TrafficLocalPort, qtechIPSec2TrafficRemoteAddr1, qtechIPSec2TrafficRemoteAddr2, qtechIPSec2TrafficRemotePort } ::= { qtechIPSec2TunnelTable 1 } QtechIPSec2TunnelEntry ::= SEQUENCE { qtechIPSec2TunIfIndex Integer32, qtechIPSec2TunnelTrafficIndex Integer32, qtechIPSec2TunIndex Integer32, qtechIPSec2TunIKETunnelIndex Integer32, qtechIPSec2TunnelAhOutSaIndex Integer32, qtechIPSec2TunnelAhInSaIndex Integer32, qtechIPSec2TunnelEspOutSaIndex Integer32, qtechIPSec2TunnelEspInSaIndex Integer32, qtechIPSec2TunLocalAddr IpAddress, qtechIPSec2TunRemoteAddr IpAddress, qtechIPSec2TunLocalHostname DisplayString, qtechIPSec2TunRemoteHostname DisplayString, qtechIPSec2TunKeyType QtechIPSec2NegoType, qtechIPSec2TunEncapMode QtechEncapMode, qtechIPSec2TunInitiator INTEGER, qtechIPSec2TunLifeSize Integer32, qtechIPSec2TunLifeTime Integer32, qtechIPSec2TunRemainTime Integer32, qtechIPSec2TunActiveTime Integer32, qtechIPSec2TunCreateTime TimeStamp, qtechIPSec2TunRemainSize Integer32, qtechIPSec2TunTotalRefreshes Counter32, qtechIPSec2TunCurrentSaInstances Gauge32, qtechIPSec2TunInSaEncryptAlgo QtechEncryptAlgo, qtechIPSec2TunInSaAhAuthAlgo QtechAuthAlgo, qtechIPSec2TunInSaEspAuthAlgo QtechAuthAlgo, qtechIPSec2TunDiffHellmanGrp QtechDiffHellmanGrp, qtechIPSec2TunOutSaEncryptAlgo QtechEncryptAlgo, qtechIPSec2TunOutSaAhAuthAlgo QtechAuthAlgo, qtechIPSec2TunOutSaEspAuthAlgo QtechAuthAlgo, qtechIPSec2TunMapName DisplayString, qtechIPSec2TunSeqNum Integer32, qtechIPSec2TunStatus QtechIPSec2TunnelState } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.1 qtechIPSec2TunIfIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index( the ifIndex of ifTable )." ::= { qtechIPSec2TunnelEntry 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.2 qtechIPSec2TunnelTrafficIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Description." ::= { qtechIPSec2TunnelEntry 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.3 qtechIPSec2TunIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of IPSec Phase-2 Tunnel Table. The value of the index is a number which begins at one and is incremented with each tunnel that is created. The value of this object will wrap at 2,147,483,647." ::= { qtechIPSec2TunnelEntry 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.5 qtechIPSec2TunIKETunnelIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the associated IPSec Phase-1 IKE Tunnel (IKETunIndex in the IKETunnelTable). 2147483647 is defined as invalid value. " ::= { qtechIPSec2TunnelEntry 5 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.6 qtechIPSec2TunnelAhOutSaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Description." ::= { qtechIPSec2TunnelEntry 6 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.7 qtechIPSec2TunnelAhInSaIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the associated IPSec Phase-1 IKE Tunnel (IKETunIndex in the IKETunnelTable). 2147483647 is defined as invalid value. " ::= { qtechIPSec2TunnelEntry 7 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.8 qtechIPSec2TunnelEspOutSaIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the associated IPSec Phase-1 IKE Tunnel (IKETunIndex in the IKETunnelTable). 2147483647 is defined as invalid value. " ::= { qtechIPSec2TunnelEntry 8 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.9 qtechIPSec2TunnelEspInSaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Description." ::= { qtechIPSec2TunnelEntry 9 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.10 qtechIPSec2TunLocalAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the local peer for the IPSec Phase-2 Tunnel. 0.0.0.0 is defined as invalid value." ::= { qtechIPSec2TunnelEntry 10 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.11 qtechIPSec2TunRemoteAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the remote peer for the IPSec Phase-2 Tunnel. 0.0.0.0 is defined as invalid value." ::= { qtechIPSec2TunnelEntry 11 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.12 qtechIPSec2TunLocalHostname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of the local peer for the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 12 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.13 qtechIPSec2TunRemoteHostname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of the remote peer for the IPSec Phase-2 Tunnel. " ::= { qtechIPSec2TunnelEntry 13 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.14 qtechIPSec2TunKeyType OBJECT-TYPE SYNTAX QtechIPSec2NegoType MAX-ACCESS read-only STATUS current DESCRIPTION "The key negotiate mode used by the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 14 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.15 qtechIPSec2TunEncapMode OBJECT-TYPE SYNTAX QtechEncapMode MAX-ACCESS read-only STATUS current DESCRIPTION "The encapsulation mode used by the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 15 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.16 qtechIPSec2TunInitiator OBJECT-TYPE SYNTAX INTEGER { local(1), remote(2), none(2147483647) } MAX-ACCESS read-only STATUS current DESCRIPTION "The initiator of this IPSec tunnel. Value none is used for manual IPsec tunnel, for there is no initiator or responder in this method." ::= { qtechIPSec2TunnelEntry 16 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.17 qtechIPSec2TunLifeSize OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated LifeSize of the IPSec Phase-2 Tunnel in kilobytes. 2147483647 is defined as invalid value." ::= { qtechIPSec2TunnelEntry 17 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.18 qtechIPSec2TunLifeTime OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The negotiated LifeTime of the IPSec Phase-2 Tunnel in seconds. 2147483647 is defined as invalid value." ::= { qtechIPSec2TunnelEntry 18 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.19 qtechIPSec2TunRemainTime OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The remain time of SA in seconds. 2147483647 is defined as invalid value." ::= { qtechIPSec2TunnelEntry 19 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.20 qtechIPSec2TunActiveTime OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The duration the IPSec Phase-2 Tunnel has been active in hundredths of seconds. 2147483647 is defined as invalid value." ::= { qtechIPSec2TunnelEntry 20 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.21 qtechIPSec2TunCreateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The Time Stamp when the IPSec Phase-2 Tunnel created." ::= { qtechIPSec2TunnelEntry 21 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.23 qtechIPSec2TunRemainSize OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The remain LifeSize of SA in kilobytes. 2147483647 is defined as invalid value." ::= { qtechIPSec2TunnelEntry 23 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.24 qtechIPSec2TunTotalRefreshes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of security association refreshing performed." ::= { qtechIPSec2TunnelEntry 24 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.25 qtechIPSec2TunCurrentSaInstances OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of security associations which are currently active or expiring." ::= { qtechIPSec2TunnelEntry 25 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.26 qtechIPSec2TunInSaEncryptAlgo OBJECT-TYPE SYNTAX QtechEncryptAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption algorithm used by the inbound security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 26 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.27 qtechIPSec2TunInSaAhAuthAlgo OBJECT-TYPE SYNTAX QtechAuthAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm used by the inbound authentication header (AH) security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 27 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.28 qtechIPSec2TunInSaEspAuthAlgo OBJECT-TYPE SYNTAX QtechAuthAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm used by the inbound encapsulation security protocol(ESP) security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 28 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.29 qtechIPSec2TunDiffHellmanGrp OBJECT-TYPE SYNTAX QtechDiffHellmanGrp MAX-ACCESS read-only STATUS current DESCRIPTION "The Diffie Hellman Group used by the security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 29 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.30 qtechIPSec2TunOutSaEncryptAlgo OBJECT-TYPE SYNTAX QtechEncryptAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption algorithm used by the outbound security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 30 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.31 qtechIPSec2TunOutSaAhAuthAlgo OBJECT-TYPE SYNTAX QtechAuthAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm used by the outbound authentication header (AH) security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 31 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.32 qtechIPSec2TunOutSaEspAuthAlgo OBJECT-TYPE SYNTAX QtechAuthAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm used by the outbound encapsulation security protocol(ESP) security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelEntry 32 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.33 qtechIPSec2TunMapName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Map name used by this IPSec tunnel." ::= { qtechIPSec2TunnelEntry 33 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.34 qtechIPSec2TunSeqNum OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number of policy used by this IPSec tunnel." ::= { qtechIPSec2TunnelEntry 34 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.1.1.35 qtechIPSec2TunStatus OBJECT-TYPE SYNTAX QtechIPSec2TunnelState MAX-ACCESS read-write STATUS current DESCRIPTION "The status of the IPSec Tunnel." ::= { qtechIPSec2TunnelEntry 35 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2 qtechIPSec2TunnelStatTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechIPSec2TunnelStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IPSec Phase-2 Tunnel Statistics Table. " ::= { qtechIPSec2Objects 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1 qtechIPSec2TunnelStatEntry OBJECT-TYPE SYNTAX QtechIPSec2TunnelStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about QtechIPSec2TunnelStatTable." INDEX { qtechIPSec2TunIndex } ::= { qtechIPSec2TunnelStatTable 1 } QtechIPSec2TunnelStatEntry ::= SEQUENCE { qtechIPSec2TunInOctets Counter64, qtechIPSec2TunInDecompOctets Counter64, qtechIPSec2TunInPkts Counter64, qtechIPSec2TunInSpeed Counter64, qtechIPSec2TunInDropPkts Counter64, qtechIPSec2TunOutOctets Counter64, qtechIPSec2TunOutUncompOctets Counter64, qtechIPSec2TunOutPkts Counter64, qtechIPSec2TunOutSpeed Counter64, qtechIPSec2TunOutDropPkts Counter64 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.1 qtechIPSec2TunInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received by this IPSec Phase-2 Tunnel. This value is accumulated BEFORE determining whether or not the packet should be decompressed." ::= { qtechIPSec2TunnelStatEntry 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.2 qtechIPSec2TunInDecompOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of decompressed octets received by this IPSec Phase-2 Tunnel. This value is accumulated AFTER the packet is decompressed." ::= { qtechIPSec2TunnelStatEntry 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.3 qtechIPSec2TunInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelStatEntry 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.4 qtechIPSec2TunInSpeed OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The Speed(bps) of packets received by this IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelStatEntry 4 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.5 qtechIPSec2TunInDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets dropped during receiving process by this IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelStatEntry 5 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.6 qtechIPSec2TunOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets sent by this IPSec Phase-2 Tunnel. This value is accumulated AFTER determining whether or not the packet should be compressed." ::= { qtechIPSec2TunnelStatEntry 6 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.7 qtechIPSec2TunOutUncompOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of uncompressed octets sent by this IPSec Phase-2 Tunnel.This value is accumulated BEFORE the packet is compressed." ::= { qtechIPSec2TunnelStatEntry 7 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.8 qtechIPSec2TunOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets sent by this IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelStatEntry 8 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.9 qtechIPSec2TunOutSpeed OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The Speed(bps) of packets sent by this IPSec Phase-2 Tunnel. " ::= { qtechIPSec2TunnelStatEntry 9 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.2.1.10 qtechIPSec2TunOutDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets dropped during sending process by this IPSec Phase-2 Tunnel." ::= { qtechIPSec2TunnelStatEntry 10 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3 qtechIPSec2SaTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechIPSec2SaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IPSec Phase-2 Security Protection Index Table. This table contains an entry for each active and expiring security association." ::= { qtechIPSec2Objects 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1 qtechIPSec2SaEntry OBJECT-TYPE SYNTAX QtechIPSec2SaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about QtechIPSec2SaTable." INDEX { qtechIPSec2SaIndex } ::= { qtechIPSec2SaTable 1 } QtechIPSec2SaEntry ::= SEQUENCE { qtechIPSec2SaIndex Integer32, qtechIPSec2SaDirection INTEGER, qtechIPSec2SaValue Unsigned32, qtechIPSec2SaProtocol QtechSaProtocol, qtechIPSec2SaEncryptAlgo QtechEncryptAlgo, qtechIPSec2SaAuthAlgo QtechAuthAlgo, qtechIPSec2SaStatus QtechIPSec2TunnelState } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1.1 qtechIPSec2SaIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of the Sa associated with the Phase-2 Tunnel Table. The value of this index is a number which begins at one and is incremented with each Sa associated with an IPSec Phase-2 Tunnel. The value of this object will wrap at 2,147,483,647." ::= { qtechIPSec2SaEntry 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1.2 qtechIPSec2SaDirection OBJECT-TYPE SYNTAX INTEGER { in(1), out(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The direction of the SA." ::= { qtechIPSec2SaEntry 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1.3 qtechIPSec2SaValue OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the SPI." ::= { qtechIPSec2SaEntry 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1.4 qtechIPSec2SaProtocol OBJECT-TYPE SYNTAX QtechSaProtocol MAX-ACCESS read-only STATUS current DESCRIPTION "The security protocol of the SA." ::= { qtechIPSec2SaEntry 4 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1.5 qtechIPSec2SaEncryptAlgo OBJECT-TYPE SYNTAX QtechEncryptAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption algorithm used by the security association of the IPSec Phase-2 Tunnel." ::= { qtechIPSec2SaEntry 5 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1.6 qtechIPSec2SaAuthAlgo OBJECT-TYPE SYNTAX QtechAuthAlgo MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm used by the SA." ::= { qtechIPSec2SaEntry 6 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.3.1.7 qtechIPSec2SaStatus OBJECT-TYPE SYNTAX QtechIPSec2TunnelState MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the SA." ::= { qtechIPSec2SaEntry 7 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4 qtechIPSec2TrafficTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechIPSec2TrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IPSec Phase-2 Tunnel Traffic Table. " ::= { qtechIPSec2Objects 4 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1 qtechIPSec2TrafficEntry OBJECT-TYPE SYNTAX QtechIPSec2TrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about QtechIPSec2TrafficTable." INDEX { qtechIPSec2TunnelTrafficIndex } ::= { qtechIPSec2TrafficTable 1 } QtechIPSec2TrafficEntry ::= SEQUENCE { qtechIPSec2TrafficIndex Integer32, qtechIPSec2TrafficLocalType QtechTrafficType, qtechIPSec2TrafficLocalAddr1 IpAddress, qtechIPSec2TrafficLocalAddr2 IpAddress, qtechIPSec2TrafficLocalProtocol Integer32, qtechIPSec2TrafficLocalPort Integer32, qtechIPSec2TrafficLocalHostname DisplayString, qtechIPSec2TrafficRemoteType QtechTrafficType, qtechIPSec2TrafficRemoteAddr1 IpAddress, qtechIPSec2TrafficRemoteAddr2 IpAddress, qtechIPSec2TrafficRemoteProtocol Integer32, qtechIPSec2TrafficRemotePort Integer32, qtechIPSec2TrafficRemoteHostname DisplayString } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.1 qtechIPSec2TrafficIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Description." ::= { qtechIPSec2TrafficEntry 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.2 qtechIPSec2TrafficLocalType OBJECT-TYPE SYNTAX QtechTrafficType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of local peer. Possible values are: a single IP address, or an IP address range, or an IP subnet." ::= { qtechIPSec2TrafficEntry 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.3 qtechIPSec2TrafficLocalAddr1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The first specification of local peer's IP address. If the local peer type is single IP address, then this is the value of the IP address. If the local peer type is IP subnet, then this is the value of the subnet. If the local peer type is IP address range, then this is the value of beginning IP address of the range." ::= { qtechIPSec2TrafficEntry 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.4 qtechIPSec2TrafficLocalAddr2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The second specification of local peer's IP address. If the local peer type is single IP address, then this is the value of the IP address. If the local peer type is IP subnet, then this is the value of the subnet mask. If the local peer type is IP address range, then this is the value of ending IP address of the range." ::= { qtechIPSec2TrafficEntry 4 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.5 qtechIPSec2TrafficLocalProtocol OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol number of the local peer's traffic." ::= { qtechIPSec2TrafficEntry 5 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.6 qtechIPSec2TrafficLocalPort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the local peer's traffic." ::= { qtechIPSec2TrafficEntry 6 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.7 qtechIPSec2TrafficLocalHostname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of local peer's IP address." ::= { qtechIPSec2TrafficEntry 7 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.8 qtechIPSec2TrafficRemoteType OBJECT-TYPE SYNTAX QtechTrafficType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of remote peer. Possible values are: a single IP address, or an IP address range, or an IP subnet." ::= { qtechIPSec2TrafficEntry 8 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.9 qtechIPSec2TrafficRemoteAddr1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The first specification of remote peer's IP address. If the remote peer type is single IP address, then this is the value of the IP address. If the remote peer type is IP subnet, then this is the value of the subnet. If the remote peer type is IP address range, then this is the value of beginning IP address of the range." ::= { qtechIPSec2TrafficEntry 9 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.10 qtechIPSec2TrafficRemoteAddr2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Single IP address, then this is the value of the IP address. If the remote peer type is IP subnet, then this is the value of the subnet mask. If the remote peer type is IP address range, then this is the value of ending IP address of the range." ::= { qtechIPSec2TrafficEntry 10 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.11 qtechIPSec2TrafficRemoteProtocol OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol number of the remote peer's traffic." ::= { qtechIPSec2TrafficEntry 11 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.12 qtechIPSec2TrafficRemotePort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the remote peer's traffic." ::= { qtechIPSec2TrafficEntry 12 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.4.1.13 qtechIPSec2TrafficRemoteHostname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of remote peer's IP address." ::= { qtechIPSec2TrafficEntry 13 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5 qtechIPSec2GlobalStats OBJECT IDENTIFIER ::= { qtechIPSec2Objects 5 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.1 qtechIPSec2GlobalActiveTunnels OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of currently active IPSec Phase-2 Tunnels." ::= { qtechIPSec2GlobalStats 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.2 qtechIPSec2GlobalActiveSas OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of currently active or expiring IPSec Phase-2 SA." ::= { qtechIPSec2GlobalStats 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.3 qtechIPSec2GlobalInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received by all current and previous IPSec Phase-2 Tunnels. This value is accumulated BEFORE determining whether or not the packet should be decompressed." ::= { qtechIPSec2GlobalStats 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.4 qtechIPSec2GlobalInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all current and previous IPSec Phase-2 Tunnels." ::= { qtechIPSec2GlobalStats 4 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.5 qtechIPSec2GlobalInSpeed OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total speed(bps) of packets received by all current and previous IPSec Phase-2 Tunnels." ::= { qtechIPSec2GlobalStats 5 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.6 qtechIPSec2GlobalInDrops OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets dropped during receiving process by all current and previous IPSec Phase-2 Tunnels. " ::= { qtechIPSec2GlobalStats 6 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.7 qtechIPSec2GlobalOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets sent by all current and previous IPSec Phase-2 Tunnels. This value is accumulated AFTER determining whether or not the packet should be compressed." ::= { qtechIPSec2GlobalStats 7 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.8 qtechIPSec2GlobalOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets sent by all current and previous IPSec Phase-2 Tunnels." ::= { qtechIPSec2GlobalStats 8 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.9 qtechIPSec2GlobalOutSpeed OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total speed(bps) of packets sent by all current and previous IPSec Phase-2 Tunnels." ::= { qtechIPSec2GlobalStats 9 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.5.10 qtechIPSec2GlobalOutDrops OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets dropped during sending process by all current and previous IPSec Phase-2 Tunnels." ::= { qtechIPSec2GlobalStats 10 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.6 qtechIPSec2TrapObject OBJECT IDENTIFIER ::= { qtechIPSec2Objects 6 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.6.1 qtechIPSec2MapName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The IPSec map name with a trap." ::= { qtechIPSec2TrapObject 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.6.2 qtechIPSec2SeqNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The IPSec map sequence number with a trap." ::= { qtechIPSec2TrapObject 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.6.3 qtechIPSec2SpiValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The SPI value associated with a trap." ::= { qtechIPSec2TrapObject 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.7 qtechIPSec2Trap OBJECT IDENTIFIER ::= { qtechIPSec2Objects 7 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.7.1 qtechIPSec2Notifications OBJECT IDENTIFIER ::= { qtechIPSec2Trap 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.7.1.1 qtechIPSec2TunnelStart NOTIFICATION-TYPE OBJECTS { qtechIPSec2TunIfIndex, qtechIPSec2TunRemoteAddr, qtechIPSec2TrafficLocalType, qtechIPSec2TrafficLocalAddr1, qtechIPSec2TrafficLocalAddr2, qtechIPSec2TrafficLocalProtocol, qtechIPSec2TrafficLocalPort, qtechIPSec2TrafficRemoteAddr1, qtechIPSec2TrafficRemoteAddr2, qtechIPSec2TrafficRemotePort } STATUS current DESCRIPTION "This notification is generated when an IPSec Phase-2 Tunnel is created." ::= { qtechIPSec2Notifications 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.1.7.1.2 qtechIPSec2TunnelStop NOTIFICATION-TYPE OBJECTS { qtechIPSec2TunIfIndex, qtechIPSec2TunRemoteAddr, qtechIPSec2TrafficLocalType, qtechIPSec2TrafficLocalAddr1, qtechIPSec2TrafficLocalAddr2, qtechIPSec2TrafficLocalProtocol, qtechIPSec2TrafficLocalPort, qtechIPSec2TrafficRemoteAddr1, qtechIPSec2TrafficRemoteAddr2, qtechIPSec2TrafficRemotePort } STATUS current DESCRIPTION "This notification is generated when an IPSec Phase-2 Tunnel is deleted." ::= { qtechIPSec2Notifications 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2 qtechIPSec2Conformance OBJECT IDENTIFIER ::= { qtechIPSec2MibModule 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.1 qtechIPSec2Compliances OBJECT IDENTIFIER ::= { qtechIPSec2Conformance 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.1.1 qtechIPSec2Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION " " MODULE -- this module MANDATORY-GROUPS { qtechIPSec2TunnelTableGroup, qtechIPSec2TunnelStatGroup, qtechIPSec2SaGroup, qtechIPSec2TrafficTableGroup, qtechIPSec2GlobalStatsGroup, qtechIPSec2TrapObjectGroup, qtechIPSec2TrapGroup } ::= { qtechIPSec2Compliances 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2 qtechIPSec2Groups OBJECT IDENTIFIER ::= { qtechIPSec2Conformance 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2.1 qtechIPSec2TunnelTableGroup OBJECT-GROUP OBJECTS { qtechIPSec2TunIfIndex, qtechIPSec2TunLocalAddr, qtechIPSec2TunRemoteAddr, qtechIPSec2TunLocalHostname, qtechIPSec2TunRemoteHostname, qtechIPSec2TunKeyType, qtechIPSec2TunEncapMode, qtechIPSec2TunInitiator, qtechIPSec2TunLifeSize, qtechIPSec2TunLifeTime, qtechIPSec2TunRemainTime, qtechIPSec2TunActiveTime, qtechIPSec2TunCreateTime, qtechIPSec2TunRemainSize, qtechIPSec2TunTotalRefreshes, qtechIPSec2TunCurrentSaInstances, qtechIPSec2TunInSaEncryptAlgo, qtechIPSec2TunInSaAhAuthAlgo, qtechIPSec2TunInSaEspAuthAlgo, qtechIPSec2TunDiffHellmanGrp, qtechIPSec2TunOutSaEncryptAlgo, qtechIPSec2TunOutSaAhAuthAlgo, qtechIPSec2TunOutSaEspAuthAlgo, qtechIPSec2TunMapName, qtechIPSec2TunSeqNum, qtechIPSec2TunStatus, qtechIPSec2TunInOctets, qtechIPSec2TunInDecompOctets, qtechIPSec2TunInPkts, qtechIPSec2TunInSpeed, qtechIPSec2TunInDropPkts, qtechIPSec2TunOutOctets, qtechIPSec2TunOutUncompOctets, qtechIPSec2TunOutPkts, qtechIPSec2TunOutSpeed, qtechIPSec2TunOutDropPkts } STATUS current DESCRIPTION "The group contains the IPSec tunnel's property information." ::= { qtechIPSec2Groups 1 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2.2 qtechIPSec2TunnelStatGroup OBJECT-GROUP OBJECTS { qtechIPSec2TunInOctets, qtechIPSec2TunInDecompOctets, qtechIPSec2TunInPkts, qtechIPSec2TunInSpeed, qtechIPSec2TunInDropPkts, qtechIPSec2TunOutOctets, qtechIPSec2TunOutUncompOctets, qtechIPSec2TunOutPkts, qtechIPSec2TunOutSpeed, qtechIPSec2TunOutDropPkts } STATUS current DESCRIPTION "The group contains the IPSec tunnel's statistic information." ::= { qtechIPSec2Groups 2 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2.3 qtechIPSec2SaGroup OBJECT-GROUP OBJECTS { qtechIPSec2SaIndex, qtechIPSec2SaDirection, qtechIPSec2SaValue, qtechIPSec2SaProtocol, qtechIPSec2SaEncryptAlgo, qtechIPSec2SaAuthAlgo, qtechIPSec2SaStatus } STATUS current DESCRIPTION "The group contains the SA's property information." ::= { qtechIPSec2Groups 3 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2.4 qtechIPSec2TrafficTableGroup OBJECT-GROUP OBJECTS { qtechIPSec2TrafficLocalType, qtechIPSec2TrafficLocalAddr1, qtechIPSec2TrafficLocalAddr2, qtechIPSec2TrafficLocalProtocol, qtechIPSec2TrafficLocalPort, qtechIPSec2TrafficRemoteAddr1, qtechIPSec2TrafficRemoteAddr2, qtechIPSec2TrafficRemotePort, qtechIPSec2TrafficLocalHostname, qtechIPSec2TrafficRemoteType, qtechIPSec2TrafficRemoteProtocol, qtechIPSec2TrafficRemoteHostname } STATUS current DESCRIPTION "The group contains the property information of the data flow protected by IPSec tunnel." ::= { qtechIPSec2Groups 4 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2.5 qtechIPSec2GlobalStatsGroup OBJECT-GROUP OBJECTS { qtechIPSec2GlobalActiveTunnels, qtechIPSec2GlobalActiveSas, qtechIPSec2GlobalInOctets, qtechIPSec2GlobalInPkts, qtechIPSec2GlobalInSpeed, qtechIPSec2GlobalInDrops, qtechIPSec2GlobalOutOctets, qtechIPSec2GlobalOutPkts, qtechIPSec2GlobalOutSpeed, qtechIPSec2GlobalOutDrops } STATUS current DESCRIPTION "The group contains all of the IPSec tunnel's statistic information." ::= { qtechIPSec2Groups 5 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2.6 qtechIPSec2TrapObjectGroup OBJECT-GROUP OBJECTS { qtechIPSec2MapName, qtechIPSec2SeqNum, qtechIPSec2SpiValue } STATUS current DESCRIPTION "The group contains all of trap objects of IPSec tunnels." ::= { qtechIPSec2Groups 6 } -- 1.3.6.1.4.1.27514.1.1.10.2.108.2.2.7 qtechIPSec2TrapGroup NOTIFICATION-GROUP NOTIFICATIONS { qtechIPSec2TunnelStart, qtechIPSec2TunnelStop } STATUS current DESCRIPTION "The group contains all of trap of IPSec tunnels." ::= { qtechIPSec2Groups 7 } END -- -- QTECH-IPSEC2-MIB.mib --