-- ***************************************************************** -- QTECH-ROUTE-MIB.mib: Qtech Route MIB file -- -- March 2002, Wuzg -- -- Copyright (c) 2002 by Qtech Networks Co.,Ltd. -- All rights reserved. -- -- ***************************************************************** -- QTECH-ROUTE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, Integer32, IpAddress FROM SNMPv2-SMI TruthValue, DisplayString, RowStatus, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ConfigStatus, IfIndex FROM QTECH-TC EnabledStatus FROM P-BRIDGE-MIB qtechMgmt FROM QTECH-SMI; qtechRouteMIB MODULE-IDENTITY LAST-UPDATED "200203200000Z" ORGANIZATION "Qtech Networks Co.,Ltd." CONTACT-INFO " Tel: 4008-111-000 E-mail: service@qtech.com.cn" DESCRIPTION "This module defines qtech route mibs." REVISION "200203200000Z" DESCRIPTION "Initial version of this MIB module." ::= { qtechMgmt 20} QtechRouteProtoType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Routing protocol type." SYNTAX INTEGER { other(1), --notspecified local(2), --localinterface netmgmt(3), --staticroute icmp(4), --resultofICMPRedirect egp(5), --ExteriorGatewayProtocol ggp(6), --Gateway-GatewayProtocol hello(7), --FuzzBallHelloSpeak rip(8), --BerkeleyRIPorRIP-II isis(9), --DualIS-IS esis(10), --ISO9542 ciscoigrp(11), --CiscoIGRP bbnspfigp(12), --BBNSPFIGP ospf(13), --OpenShortestPathFirst bgp(14), --BorderGatewayProtocol idpr(15), --InterDomainPolicyRouting ciscoeigrp(16), --CiscoEIGRP max(17) --MAXTYPE } qtechRouteMIBObjects OBJECT IDENTIFIER ::= { qtechRouteMIB 1 } qtechRouteServiceStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Route management function status" ::={ qtechRouteMIBObjects 1 } qtechRoutingProtoInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechRoutingProtoInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The routing protocol infomation ." ::= { qtechRouteMIBObjects 2 } qtechRoutingProtoInfoEntry OBJECT-TYPE SYNTAX QtechRoutingProtoInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { qtechRoutingProtoInfoProtoType, qtechRoutingProtoInfoGateWay } ::= { qtechRoutingProtoInfoTable 1 } QtechRoutingProtoInfoEntry ::= SEQUENCE{ qtechRoutingProtoInfoProtoType QtechRouteProtoType, qtechRoutingProtoInfoGateWay IpAddress, qtechRoutingProtoInfoDistance Unsigned32, qtechRoutingProtoInfoLastUpdate TimeTicks } qtechRoutingProtoInfoProtoType OBJECT-TYPE SYNTAX QtechRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "The routing protocol type" ::= { qtechRoutingProtoInfoEntry 1 } qtechRoutingProtoInfoGateWay OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "For rip ,the gateway is this router's neighbor. for ospf ,the gateway is the router Id of this router, New entry will be addded when router ID is changed." ::= { qtechRoutingProtoInfoEntry 2 } qtechRoutingProtoInfoDistance OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The routing protocol distance." ::= { qtechRoutingProtoInfoEntry 3 } qtechRoutingProtoInfoLastUpdate OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The last update time of the neighbor that be found. or router ID that it last change ." ::= { qtechRoutingProtoInfoEntry 4 } qtechDefRoutingCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechDefRoutingCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Default routing configuration." ::= { qtechRouteMIBObjects 3} qtechDefRoutingCfgEntry OBJECT-TYPE SYNTAX QtechDefRoutingCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry define one routing protocol's default routing configurate,if in rip routing configuration only route map is valid to this default route parameter" INDEX { qtechDefRoutingCfgRoutingProtoType} ::= { qtechDefRoutingCfgTable 1 } QtechDefRoutingCfgEntry ::= SEQUENCE { qtechDefRoutingCfgRoutingProtoType QtechRouteProtoType, qtechDefRoutingCfgAlways TruthValue, qtechDefRoutingCfgMetric Unsigned32, qtechDefRoutingCfgMetricType --only use in ospf INTEGER, qtechDefRoutingCfgRouteMap DisplayString, qtechDefRoutingCfgStatus RowStatus } qtechDefRoutingCfgRoutingProtoType OBJECT-TYPE SYNTAX QtechRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "index indicate that which routing protocol configuration mode is current mode." ::= { qtechDefRoutingCfgEntry 1 } qtechDefRoutingCfgAlways OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Setting the value to TRUE indicates that always advertise default route." DEFVAL{false} ::= { qtechDefRoutingCfgEntry 2 } qtechDefRoutingCfgMetric OBJECT-TYPE SYNTAX Unsigned32(1..16777214) MAX-ACCESS read-create STATUS current DESCRIPTION "Set ospf default metric value." DEFVAL {10} ::= { qtechDefRoutingCfgEntry 3 } qtechDefRoutingCfgMetricType OBJECT-TYPE SYNTAX INTEGER{ type1(1), type2(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set OSPF Link State type,this value is only valid in ospf configuration" DEFVAL {type2} ::= { qtechDefRoutingCfgEntry 4 } qtechDefRoutingCfgRouteMap OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Set route's Route-map reference.Null string indicate that no any route-map reference." DEFVAL {""} ::= { qtechDefRoutingCfgEntry 5 } qtechDefRoutingCfgStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "if this value is change to destroy, this entry will be deleted" ::= { qtechDefRoutingCfgEntry 6 } --Route map group qtechRouteMapMIBObjects OBJECT IDENTIFIER ::= { qtechRouteMIB 2 } --qtechRouteMapTable qtechRouteMapTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechRouteMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the route map table." ::= { qtechRouteMapMIBObjects 1 } qtechRouteMapEntry OBJECT-TYPE SYNTAX QtechRouteMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { qtechRouteMapName, qtechRouteMapSequenceNumber } ::= { qtechRouteMapTable 1 } QtechRouteMapEntry ::= SEQUENCE{ qtechRouteMapName DisplayString, qtechRouteMapSequenceNumber Unsigned32, qtechRouteMapOperType INTEGER, qtechRouteMapMatchMetric Unsigned32, qtechRouteMapMatchRouteType INTEGER, qtechRouteMapMetricValueType INTEGER, qtechRouteMapSetMetric Unsigned32, qtechRouteMapSetLevel INTEGER, qtechRouteMapSetMetricType INTEGER, qtechRouteMapSetNexthopSt ConfigStatus, qtechRouteMapSetNexthop IpAddress, qtechRouteMapStatus RowStatus } qtechRouteMapName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The route map name ,A meaningful name for the route map. The redistribute router configuration command uses this name to reference the route map. Multiple route maps might share the same map tag name. When this string be used as an index,Value of a sub-identifier equal ASCII value of corresponding character(first sub-identifier corresponds first character of string). The number of sub-identifiers of this string must be 32,If length of string is less than 32 the sub-identifier(0x0) will be filled in tail." ::= { qtechRouteMapEntry 1 } qtechRouteMapSequenceNumber OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number that indicates the position of a new route map in the list of route maps already configured with the same name." DEFVAL {10} ::= { qtechRouteMapEntry 2 } qtechRouteMapOperType OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " If permit is specified and the match criteria are met for this route map, the route is redistributed as controlled by the set actions. If deny is specified, the route is not redistributed. " DEFVAL {permit} ::= { qtechRouteMapEntry 3 } qtechRouteMapMatchMetric OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION " Match the specified route metric. The metric-value can be an IGRP 5-part metric with a value from 1 to 255. 0 indicate that this item will not be matched." DEFVAL {0} ::= { qtechRouteMapEntry 4 } qtechRouteMapMatchRouteType OBJECT-TYPE SYNTAX INTEGER{ notMatch(0), internal(1), external(2), external-type1(3), external-type2(4) } MAX-ACCESS read-create STATUS current DESCRIPTION " the route type value which route-map match, internal: OSPF intra-area and interarea routes or EIGRP internal routes, external: OSPF external routes(Type 1 or Type 2)or EIGRP external routes, external-type1: OSPF external routes Type 1 external-type2: OSPF external routes Type 2 'notMatch' indicate that this item will not be matched." DEFVAL {notMatch} ::= { qtechRouteMapEntry 5} qtechRouteMapMetricValueType OBJECT-TYPE SYNTAX INTEGER{ noOper(0), replace(1), add(2), reduce(3) } MAX-ACCESS read-create STATUS current DESCRIPTION " How to modify old metric vlaue. 'noOper': metric value will not be modified. 'replace': old metric value will be replaced by qtechRouteMapSetMetric. 'add': new metric value will equal 'old metric vlaue + qtechRouteMapSetMetric' 'reduce': new metric value will equal 'old metric vlaue - qtechRouteMapSetMetric'" DEFVAL {noOper} ::= { qtechRouteMapEntry 6 } qtechRouteMapSetMetric OBJECT-TYPE SYNTAX Unsigned32(1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION " Set the metric value to the given redistributed routes (for any protocol except IGRP or EIGRP). The metric value is an integer from 1 to 255. qtechRouteMapMetricValueType will decide real operation. The value of qtechRouteMapSetMetric is invalid in qtechRouteMapMetricValueType is 'noOper'." DEFVAL {1} ::= { qtechRouteMapEntry 7 } qtechRouteMapSetLevel OBJECT-TYPE SYNTAX INTEGER{ all(0), stubarea(1), -- OSPF NSSA backbone(2) -- OSPF backbone areas } MAX-ACCESS read-create STATUS current DESCRIPTION "Set the level for routes that are advertised into the specified area of the routing domain. 'all'indicate that routes will be advertised into all type area." DEFVAL {all} ::= { qtechRouteMapEntry 8 } qtechRouteMapSetMetricType OBJECT-TYPE SYNTAX INTEGER{ noOper(0), internal(1), external(2), type1(3), type2(4) } MAX-ACCESS read-create STATUS current DESCRIPTION " set metric type, 'external' means IS-IS external metric; 'internal' means Use IGP metric as the MED for BGP; 'type-1 ' means OSPF external type 1 metric; 'type-2 ' means OSPF external type 2 metric. 'noOper'indicate that no any opertion will be done for this item." DEFVAL {noOper} ::= { qtechRouteMapEntry 9} qtechRouteMapSetNexthopSt OBJECT-TYPE SYNTAX ConfigStatus MAX-ACCESS read-create STATUS current DESCRIPTION " How to modify nexthop vlaue. 'invalid': nexthop value will not be modified. 'valid': nexthop value will be modified to qtechRouteMapSetNexthop. Setting this value to 'valid' have no any effect.This value will be changed to 'valid' when setting 'qtechRouteMapSetNexthop'" DEFVAL {invalid} ::= { qtechRouteMapEntry 10 } qtechRouteMapSetNexthop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION " Set the nexthop value to give the redistributed routes" ::= { qtechRouteMapEntry 11 } qtechRouteMapStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " if this value is destroy,the entry will be delete." ::= { qtechRouteMapEntry 12 } --qtechRouteMapMatchIpAddressTable qtechRouteMapMatchIpAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechRouteMapMatchIpAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the match ip address item of the route map ." ::= { qtechRouteMapMIBObjects 2 } qtechRouteMapMatchIpAddressEntry OBJECT-TYPE SYNTAX QtechRouteMapMatchIpAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match a standard access list by specifying the Acl name " INDEX { qtechRouteMapName, qtechRouteMapSequenceNumber, qtechRouteMapMatchType, qtechRouteMapMatchIpAddressAclName } ::= { qtechRouteMapMatchIpAddressTable 1 } QtechRouteMapMatchIpAddressEntry ::= SEQUENCE{ qtechRouteMapMatchType INTEGER, qtechRouteMapMatchIpAddressAclName DisplayString, qtechRouteMapMatchIpAddressStatus RowStatus } qtechRouteMapMatchType OBJECT-TYPE SYNTAX INTEGER{ destination(1), nextHop(2), source(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "destination(1):match route destination ip address nextHop(2):match route nextHop ip address source(3):match route source ip address " ::= { qtechRouteMapMatchIpAddressEntry 1 } qtechRouteMapMatchIpAddressAclName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acl name apply to ip address. When this string be used as an index,Value of a sub-identifier equal ASCII value of corresponding character(first sub-identifier corresponds first character of string). The number of sub-identifiers of this string must be 32,If length of string is less than 32 the sub-identifier(0x0) will be filled in tail." ::= { qtechRouteMapMatchIpAddressEntry 2 } qtechRouteMapMatchIpAddressStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The entry status,if the value is destroy ,the entry will be deleted." ::= { qtechRouteMapMatchIpAddressEntry 3 } --qtechRouteMapMatchTagTable qtechRouteMapMatchTagTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechRouteMapMatchTagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match a tag value item of route map " ::= { qtechRouteMapMIBObjects 3 } qtechRouteMapMatchTagEntry OBJECT-TYPE SYNTAX QtechRouteMapMatchTagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match the specified tag value in a list of one or more route tag values. Each can be an integer from 0 to 4294967295. " INDEX { qtechRouteMapName, qtechRouteMapSequenceNumber, qtechRouteMapMatchTagValue } ::= { qtechRouteMapMatchTagTable 1 } QtechRouteMapMatchTagEntry ::= SEQUENCE{ qtechRouteMapMatchTagValue Unsigned32, qtechRouteMapMatchTagStatus RowStatus } qtechRouteMapMatchTagValue OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " Match the specified tag value." ::= { qtechRouteMapMatchTagEntry 1 } qtechRouteMapMatchTagStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " the entry status,if the value is destroy ,the entry will be deleted." ::= { qtechRouteMapMatchTagEntry 2 } --qtechRouteMapMatchInterfaceTable qtechRouteMapMatchInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechRouteMapMatchInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match Interface item of route map ." ::= { qtechRouteMapMIBObjects 4 } qtechRouteMapMatchInterfaceEntry OBJECT-TYPE SYNTAX QtechRouteMapMatchInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match the specified next hop route out one of the specified interfaces. " INDEX { qtechRouteMapName, qtechRouteMapSequenceNumber, qtechRouteMapMatchInterfaceIfIndex } ::= { qtechRouteMapMatchInterfaceTable 1 } QtechRouteMapMatchInterfaceEntry ::= SEQUENCE{ qtechRouteMapMatchInterfaceIfIndex IfIndex, qtechRouteMapMatchInterfaceStatus RowStatus } qtechRouteMapMatchInterfaceIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION " The ifTable's ifIndex." ::= { qtechRouteMapMatchInterfaceEntry 1 } qtechRouteMapMatchInterfaceStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " the entry status,if the value is destroy ,the entry will be deleted." ::= { qtechRouteMapMatchInterfaceEntry 2 } --Route redistribute group qtechRouteRedistributeMIBObjects OBJECT IDENTIFIER ::= { qtechRouteMIB 3 } --Routing Redistribute table qtechRouteRedistributeTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechRouteRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " this table descripts the redistributing methods." ::= { qtechRouteRedistributeMIBObjects 1 } qtechRouteRedistributeEntry OBJECT-TYPE SYNTAX QtechRouteRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "each entry descripts the methord,when Redistribute routes from one routing protocol to another routing protocol." INDEX {qtechRouteRedistributeProtocolCfg, qtechRouteRedistributeProtocol } ::= { qtechRouteRedistributeTable 1 } QtechRouteRedistributeEntry ::= SEQUENCE{ qtechRouteRedistributeProtocolCfg QtechRouteProtoType, qtechRouteRedistributeProtocol QtechRouteProtoType, qtechRouteRedistributeMetricValue Unsigned32, qtechRouteRedistributeMetricType INTEGER, qtechRouteRedistributeTagValue Unsigned32, qtechRouteRedistributeRouteMapName DisplayString, qtechRouteRedistributeStatus RowStatus } qtechRouteRedistributeProtocolCfg OBJECT-TYPE SYNTAX QtechRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol which the redistributing will be setted in." ::={qtechRouteRedistributeEntry 1} qtechRouteRedistributeProtocol OBJECT-TYPE SYNTAX QtechRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol which routing will redistribute to ." ::={qtechRouteRedistributeEntry 2} qtechRouteRedistributeMetricValue OBJECT-TYPE SYNTAX Unsigned32(1..16777214) MAX-ACCESS read-create STATUS current DESCRIPTION "0 indicate that redistributing metric value will equal qtechOspfRouteRedisDefMetricVal for OSPF or qtechRipOffsetMetric for RIP. Other value indicate that qtechRouteRedistributeMetricValue will be set for new metric value for redistribute routes,for rip this value only can be from 1 to 16." DEFVAL {0} ::= { qtechRouteRedistributeEntry 3 } qtechRouteRedistributeMetricType OBJECT-TYPE SYNTAX INTEGER{ type1(1), type2(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " Metric type value ." DEFVAL {type2} ::= { qtechRouteRedistributeEntry 4 } qtechRouteRedistributeTagValue OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION " Set tag for routes redistributed into OSPF." DEFVAL {0} ::= { qtechRouteRedistributeEntry 5 } qtechRouteRedistributeRouteMapName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Set route's Route-map reference.Null string indicate that no any route-map reference." DEFVAL {""} ::= { qtechRouteRedistributeEntry 6 } qtechRouteRedistributeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " the entry status,if the value is destroy ,then disable this redistribute." ::= { qtechRouteRedistributeEntry 7 } qtechRouteFilteringMIBObjects OBJECT IDENTIFIER ::= { qtechRouteMIB 4 } --ip prefix-list table qtechIpPrefixListTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechIpPrefixListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " this table descripts the ip prefix list." ::= { qtechRouteFilteringMIBObjects 1 } qtechIpPrefixListEntry OBJECT-TYPE SYNTAX QtechIpPrefixListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "each entry descripts a prefix list" INDEX {qtechIpPrefixListName, qtechIpPrefixListSequence } ::= { qtechIpPrefixListTable 1 } QtechIpPrefixListEntry ::= SEQUENCE{ qtechIpPrefixListName DisplayString, qtechIpPrefixListSequence Unsigned32, qtechIpPrefixListOperMethod INTEGER, qtechIpPrefixListIpAddress IpAddress, qtechIpPrefixListMaskLength Unsigned32, qtechIpPrefixListMinimumPrefixLength Unsigned32, qtechIpPrefixListMaximumPrefixLength Unsigned32, qtechIpPrefixListStatus RowStatus } qtechIpPrefixListName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "name of ip prefix-list name." ::={qtechIpPrefixListEntry 1} qtechIpPrefixListSequence OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "sequence can be set either automatically or manually. if 0 is seted,that means sequence will be created automatically. In the case that sequential numbers are set manually, the user may pick any number less than 2147483647 and more than 1. In the case that sequential number are set automatically, the sequential number will increase by a unit of five (5) per list. If a list with no specified sequential number is created after a list with a specified sequential number, the list will automatically pick the next multiple of five (5) as the list number. For example, if a list with number 2 already exists and a new list with no specified number is created, the next list will be numbered 5. If lists 2 and 7 already exist and a new list with no specified number is created, the new list will be numbered 10." ::={qtechIpPrefixListEntry 2} qtechIpPrefixListOperMethod OBJECT-TYPE SYNTAX INTEGER{ permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "this field specifies whether the prefix for this entry is to permit or deny the listed prefix." ::={qtechIpPrefixListEntry 3} qtechIpPrefixListIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "ip prefix-list ip address." ::={qtechIpPrefixListEntry 4} qtechIpPrefixListMaskLength OBJECT-TYPE SYNTAX Unsigned32(0..32) MAX-ACCESS read-create STATUS current DESCRIPTION "ip prefix-list mask length." ::={qtechIpPrefixListEntry 5} qtechIpPrefixListMinimumPrefixLength OBJECT-TYPE SYNTAX Unsigned32(0..32) MAX-ACCESS read-create STATUS current DESCRIPTION "this field specifies prefix length. The prefix list will be applied if the prefix length is greater than or equal to qtechIpPrefixListMinimumPrefixLength. value '0' means that this parameter has no effect. The condition 'qtechIpPrefixListMaximumPrefixLength >= qtechIpPrefixListMinimumPrefixLength > qtechIpPrefixListMaskLength' must be satisfied when this value is not '0' " ::={qtechIpPrefixListEntry 6} qtechIpPrefixListMaximumPrefixLength OBJECT-TYPE SYNTAX Unsigned32(0..32) MAX-ACCESS read-create STATUS current DESCRIPTION "this field specifies prefix length. The prefix list will be applied if the prefix length is less than or equal to qtechIpPrefixListMaximumPrefixLength. value '0' means that this parameter has no effect. The condition 'qtechIpPrefixListMaximumPrefixLength >= qtechIpPrefixListMinimumPrefixLength > qtechIpPrefixListMaskLength' must be satisfied when this value is not '0' " ::={qtechIpPrefixListEntry 7} qtechIpPrefixListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "the entry status,if the value is destroy ,then delete this ip prefix-list." ::={qtechIpPrefixListEntry 8} --distribute-list table --distribute-list is used for Filtering both input and output of the routing information qtechDistributeListTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechDistributeListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " this table descripts the distribute list." ::= { qtechRouteFilteringMIBObjects 2 } qtechDistributeListEntry OBJECT-TYPE SYNTAX QtechDistributeListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "distribute-list can be applied to both incoming and outgoing routing information,Permit or deny routes from being advertised in routing updates depending upon the action listed in the access list or ip prefix list." INDEX {qtechDistributeListCfgProtoType, qtechDistributeListIfIndex, qtechDistributeListDirection, qtechDistributeListFilteringProtocol } ::= { qtechDistributeListTable 1 } QtechDistributeListEntry ::= SEQUENCE{ qtechDistributeListCfgProtoType QtechRouteProtoType, qtechDistributeListIfIndex Unsigned32, qtechDistributeListDirection INTEGER, qtechDistributeListFilteringProtocol Unsigned32, qtechDistributeListFilterType INTEGER, qtechDistributeListAclName DisplayString, qtechDistributeListGateWayIpPrefixName DisplayString, qtechDistributeListPrefixIpPrefixName DisplayString, qtechDistributeListStatus RowStatus } qtechDistributeListCfgProtoType OBJECT-TYPE SYNTAX QtechRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "This index indicate that which routing protocol configuration mode is current mode." ::={qtechDistributeListEntry 1} qtechDistributeListIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface that this distribute list apply to. If this value is 0,it indicate that this distribute list apply in all interfaces. Other value is equal to TEXTUAL-CONVENTION 'IfIndex' meaning." ::={qtechDistributeListEntry 2} qtechDistributeListDirection OBJECT-TYPE SYNTAX INTEGER{ out(1), in(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "If direct is 'in' the distribute list is applied to input packets£¬ If direct is 'out' the distribute list is applied to output packets." ::={qtechDistributeListEntry 3} qtechDistributeListFilteringProtocol OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "If this value is 0,it indicate that this distribute list will apply on all protocol. Other value is equal to TEXTUAL-CONVENTION 'QtechRouteProtoType' meaning, it indicate the protocol which this distribute list apply on." ::={qtechDistributeListEntry 4} qtechDistributeListFilterType OBJECT-TYPE SYNTAX INTEGER{ acl(1), gateway(2), prefix(3), prefix-gateway(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "this field defines the filtering type which distribute-list used , 'acl' means filtering destination ip address of route information in incoming or outing packets; 'gateway' means filtering source ip address and mask of incoming packets; 'prefix' means filtering destination ip address and mask of route information in incoming or outing packets; 'prefix-gateway' means that firstly filtering destination ip address and mask of route information in incoming or outing packets, secondly filtering source ip address and mask of incoming packets. if Prefix-list filter is configed,Access-list filter can not be configed; if Access-list filter is configed,Prefix-list filter can not be configed." ::={qtechDistributeListEntry 5} qtechDistributeListAclName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION " This field is valid when the field qtechDistributeListFilterType's value is 'acl',it's access list name that distribute-list reference to. Null string indicate that the distribute list will not reference any ACL" ::={qtechDistributeListEntry 6} qtechDistributeListGateWayIpPrefixName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION " this field is valid when the field qtechDistributeListFilterType's value is 'gateway',it's ip prefix list name that distribute-list source ip and mask reference to. Null string indicate that the distribute list source ip and mask will not reference any ip prefix list." ::={qtechDistributeListEntry 7} qtechDistributeListPrefixIpPrefixName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION " this field is valid when the field qtechDistributeListFilterType's value is 'gateway',it's ip prefix list name that distribute-list destination ip and mask reference to. Null string indicate that the distribute list destination ip and mask will not reference any ip prefix list." ::={qtechDistributeListEntry 8} qtechDistributeListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "the entry status,if the value is destroy ,then delete this distribute-list." ::={qtechDistributeListEntry 9} qtechipCidrRouteExtendMIBObjects OBJECT IDENTIFIER ::= { qtechRouteMIB 5 } qtechipCidrRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechIpCidrRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entity's IP Routing table." REFERENCE "RFC 1213 Section 6.6, The IP Group" ::= { qtechipCidrRouteExtendMIBObjects 1 } qtechipCidrRouteEntry OBJECT-TYPE SYNTAX QtechIpCidrRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A particular route to a particular destina- tion, under a particular policy." INDEX { qtechipCidrRouteDest, qtechipCidrRouteMask, qtechipCidrRouteTos, qtechipCidrRouteNextHop } ::= { qtechipCidrRouteTable 1 } QtechIpCidrRouteEntry ::= SEQUENCE { qtechipCidrRouteDest IpAddress, qtechipCidrRouteMask IpAddress, qtechipCidrRouteTos Integer32, qtechipCidrRouteNextHop IpAddress, qtechipCidrRouteIfIndex Integer32, qtechipCidrRouteType INTEGER, qtechipCidrRouteProto INTEGER, qtechipCidrRouteAge Integer32, qtechipCidrRouteInfo OBJECT IDENTIFIER, qtechipCidrRouteNextHopAS Integer32, qtechipCidrRouteMetric1 Integer32, qtechipCidrRouteMetric2 Integer32, qtechipCidrRouteMetric3 Integer32, qtechipCidrRouteMetric4 Integer32, qtechipCidrRouteMetric5 Integer32, qtechipCidrRouteStatus RowStatus, qtechipCidrOspfRouteType INTEGER } qtechipCidrRouteDest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the ipCidrRouteMask object is not equal to x." ::= { qtechipCidrRouteEntry 1 } qtechipCidrRouteMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipCidrRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipCidrRouteMask by reference to the IP Ad- dress Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the ipCidrRouteDest object is not equal to ipCidrRoute- Dest." ::= { qtechipCidrRouteEntry 2 } -- The following convention is included for specification -- of TOS Field contents. At this time, the Host Requirements -- and the Router Requirements documents disagree on the width -- of the TOS field. This mapping describes the Router -- Requirements mapping, and leaves room to widen the TOS field -- without impact to fielded systems. qtechipCidrRouteTos OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The policy specifier is the IP TOS Field. The encoding of IP TOS is as specified by the following convention. Zero indicates the default path if no more specific policy applies. +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | PRECEDENCE | TYPE OF SERVICE | 0 | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30" ::= { qtechipCidrRouteEntry 3 } qtechipCidrRouteNextHop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0." ::= { qtechipCidrRouteEntry 4 } qtechipCidrRouteIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The ifIndex value which identifies the local interface through which the next hop of this route should be reached." DEFVAL { 0 } ::= { qtechipCidrRouteEntry 5 } qtechipCidrRouteType OBJECT-TYPE SYNTAX INTEGER { other (1), -- not specified by this MIB reject (2), -- route which discards traffic local (3), -- local interface remote (4) -- remote destination } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is not the final destina- tion. Routes which do not result in traffic forwarding or rejection should not be displayed even if the implementation keeps them stored internally. reject (2) refers to a route which, if matched, discards the message as unreachable. This is used in some protocols as a means of correctly aggregating routes." ::= { qtechipCidrRouteEntry 6 } qtechipCidrRouteProto OBJECT-TYPE SYNTAX INTEGER { other (1), -- not specified local (2), -- local interface netmgmt (3), -- static route icmp (4), -- result of ICMP Redirect -- the following are all dynamic -- routing protocols egp (5), -- Exterior Gateway Protocol ggp (6), -- Gateway-Gateway Protocol hello (7), -- FuzzBall HelloSpeak rip (8), -- Berkeley RIP or RIP-II isIs (9), -- Dual IS-IS esIs (10), -- ISO 9542 ciscoIgrp (11), -- Cisco IGRP bbnSpfIgp (12), -- BBN SPF IGP ospf (13), -- Open Shortest Path First bgp (14), -- Border Gateway Protocol idpr (15), -- InterDomain Policy Routing ciscoEigrp (16), -- Cisco EIGRP policy (17) -- Qtech private policy-route } MAX-ACCESS read-only STATUS current DESCRIPTION "The routing mechanism via which this route was learned. Inclusion of values for gateway rout- ing protocols is not intended to imply that hosts should support those protocols." ::= { qtechipCidrRouteEntry 7 } qtechipCidrRouteAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned." DEFVAL { 0 } ::= { qtechipCidrRouteEntry 8 } qtechipCidrRouteInfo OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "A reference to MIB definitions specific to the particular routing protocol which is responsi- ble for this route, as determined by the value specified in the route's ipCidrRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntactically valid object identif- ier, and any implementation conforming to ASN.1 and the Basic Encoding Rules must be able to generate and recognize this value." ::= { qtechipCidrRouteEntry 9 } qtechipCidrRouteNextHopAS OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The Autonomous System Number of the Next Hop. The semantics of this object are determined by the routing-protocol specified in the route's ipCidrRouteProto value. When this object is unknown or not relevant its value should be set to zero." DEFVAL { 0 } ::= { qtechipCidrRouteEntry 10 } qtechipCidrRouteMetric1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { qtechipCidrRouteEntry 11 } qtechipCidrRouteMetric2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { qtechipCidrRouteEntry 12 } qtechipCidrRouteMetric3 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { qtechipCidrRouteEntry 13 } qtechipCidrRouteMetric4 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { qtechipCidrRouteEntry 14 } qtechipCidrRouteMetric5 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { qtechipCidrRouteEntry 15 } qtechipCidrRouteStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status variable, used according to row installation and removal conventions." ::= { qtechipCidrRouteEntry 16 } qtechipCidrOspfRouteType OBJECT-TYPE SYNTAX INTEGER { ospf-route (0), --ospf intra area route ospf-ia-route (1), --ospf inter area route ospf-n1-route (2), --ospf nssa external type 1 route ospf-n2-route (3), --ospf nssa external type 2 route ospf-e1-route (4), --ospf external type 1 route ospf-e2-route (5) --OSPF external type 2 route } MAX-ACCESS read-only STATUS current DESCRIPTION "this field describles the ospf route entry's type, it's valid when this route was learned by ospf protocol." ::= { qtechipCidrRouteEntry 17 } qtechRouteMIBConformance OBJECT IDENTIFIER ::= { qtechRouteMIB 6 } qtechRouteMIBCompliances OBJECT IDENTIFIER ::= { qtechRouteMIBConformance 1 } qtechRouteMIBGroups OBJECT IDENTIFIER ::= { qtechRouteMIBConformance 2 } -- compliance statements qtechRouteMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Qtech Route MIB" MODULE -- this module MANDATORY-GROUPS { qtechRouteMIBGroup, qtechRouteInfoMIBGroup, qtechRouteMapMIBGroup, qtechRouteRedistributeMIBGroup , qtechRouteFilteringMibGroup, qtechipCidrRouteMibGroup } ::= { qtechRouteMIBCompliances 1 } -- units of conformance qtechRouteMIBGroup OBJECT-GROUP OBJECTS { qtechRouteServiceStatus } STATUS current DESCRIPTION "A collection of objects providing route managment." ::= { qtechRouteMIBGroups 1 } qtechRouteInfoMIBGroup OBJECT-GROUP OBJECTS { qtechRoutingProtoInfoProtoType, qtechRoutingProtoInfoGateWay , qtechRoutingProtoInfoDistance , qtechRoutingProtoInfoLastUpdate, qtechDefRoutingCfgRoutingProtoType, qtechDefRoutingCfgAlways , qtechDefRoutingCfgMetric, qtechDefRoutingCfgMetricType, qtechDefRoutingCfgRouteMap, qtechDefRoutingCfgStatus } STATUS current DESCRIPTION "A collection of objects providing route information for all routing protocol." ::= { qtechRouteMIBGroups 2} qtechRouteMapMIBGroup OBJECT-GROUP OBJECTS { qtechRouteMapName, qtechRouteMapSequenceNumber, qtechRouteMapOperType , qtechRouteMapMatchMetric , qtechRouteMapMatchRouteType , qtechRouteMapMetricValueType , qtechRouteMapSetMetric , qtechRouteMapSetLevel , qtechRouteMapSetMetricType , qtechRouteMapSetNexthopSt, qtechRouteMapSetNexthopSt, qtechRouteMapStatus, qtechRouteMapMatchIpAddressAclName, qtechRouteMapMatchType, qtechRouteMapMatchIpAddressStatus, qtechRouteMapMatchTagValue , qtechRouteMapMatchTagStatus, qtechRouteMapMatchInterfaceIfIndex, qtechRouteMapMatchInterfaceStatus } STATUS current DESCRIPTION "A collection of objects providing route managment." ::= { qtechRouteMIBGroups 3 } qtechRouteRedistributeMIBGroup OBJECT-GROUP OBJECTS { -- qtechRouteRedistributeDefMetricVal, qtechRouteRedistributeProtocolCfg, qtechRouteRedistributeProtocol, qtechRouteRedistributeMetricValue, qtechRouteRedistributeMetricType, qtechRouteRedistributeTagValue, qtechRouteRedistributeRouteMapName, qtechRouteRedistributeStatus } STATUS current DESCRIPTION "A collection of objects providing route Redistributting." ::= { qtechRouteMIBGroups 4 } qtechRouteFilteringMibGroup OBJECT-GROUP OBJECTS { qtechIpPrefixListName, qtechIpPrefixListSequence, qtechIpPrefixListOperMethod, qtechIpPrefixListIpAddress, qtechIpPrefixListMaskLength, qtechIpPrefixListMinimumPrefixLength, qtechIpPrefixListMaximumPrefixLength, qtechIpPrefixListStatus, qtechDistributeListCfgProtoType , qtechDistributeListIfIndex, qtechDistributeListFilterType, qtechDistributeListDirection , qtechDistributeListAclName, qtechDistributeListGateWayIpPrefixName, qtechDistributeListPrefixIpPrefixName, qtechDistributeListFilteringProtocol, qtechDistributeListStatus } STATUS current DESCRIPTION "A collection of objects providing route distribute-list." ::= { qtechRouteMIBGroups 5 } qtechipCidrRouteMibGroup OBJECT-GROUP OBJECTS { qtechipCidrRouteDest, qtechipCidrRouteMask, qtechipCidrRouteTos, qtechipCidrRouteNextHop, qtechipCidrRouteIfIndex, qtechipCidrRouteType, qtechipCidrRouteProto, qtechipCidrRouteAge, qtechipCidrRouteInfo, qtechipCidrRouteNextHopAS, qtechipCidrRouteMetric1, qtechipCidrRouteMetric2, qtechipCidrRouteMetric3, qtechipCidrRouteMetric4, qtechipCidrRouteMetric5, qtechipCidrRouteStatus, qtechipCidrOspfRouteType } STATUS current DESCRIPTION "A collection of objects providing CIDR Route Table." ::= { qtechRouteMIBGroups 6 } END