-- ***************************************************************** -- This mib was extracted from draft-ietf-pim-mib-v2-01.txt -- -- January 2003, zhenggao -- -- Copyright (c) 2003 by Qtech Networks Co.,Ltd. -- All rights reserved. -- -- ***************************************************************** QTECH-PIM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, IpAddress, TimeTicks FROM SNMPv2-SMI DisplayString, RowStatus, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF ipMRouteGroup, ipMRouteSource, ipMRouteSourceMask, ipMRouteNextHopGroup, ipMRouteNextHopSource, ipMRouteNextHopSourceMask, ipMRouteNextHopIfIndex, ipMRouteNextHopAddress FROM IPMROUTE-STD-MIB EnabledStatus FROM P-BRIDGE-MIB qtechMgmt FROM QTECH-SMI InterfaceIndex FROM IF-MIB; qtechPimMIB MODULE-IDENTITY LAST-UPDATED "200301200000Z" ORGANIZATION "Qtech Networks Co.,Ltd." CONTACT-INFO " Tel: 4008-111-000 E-mail: service@qtech.com.cn" DESCRIPTION "This module defines qtech Pim mibs." REVISION "200301200000Z" DESCRIPTION "Initial version of this MIB module." ::= { qtechMgmt 27} qtechPimMIBObjects OBJECT IDENTIFIER ::= { qtechPimMIB 1 } qtechPimTraps OBJECT IDENTIFIER ::= { qtechPimMIBObjects 2 } qtechPim OBJECT IDENTIFIER ::= { qtechPimMIBObjects 1 } qtechPimJoinPruneInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The default interval at which periodic PIM-SM Join/Prune messages are to be sent." DEFVAL { 60 } ::= { qtechPim 1 } -- The PIM Interface Table qtechPimInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the router's PIM interfaces. IGMP and PIM are enabled on all interfaces listed in this table." ::= { qtechPim 2 } qtechPimInterfaceEntry OBJECT-TYPE SYNTAX QtechPimInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the qtechPimInterfaceTable." INDEX { qtechPimInterfaceIfIndex } ::= { qtechPimInterfaceTable 1 } QtechPimInterfaceEntry ::= SEQUENCE { qtechPimInterfaceIfIndex InterfaceIndex, qtechPimInterfaceAddress IpAddress, qtechPimInterfaceNetMask IpAddress, qtechPimInterfaceMode INTEGER, qtechPimInterfaceDR IpAddress, qtechPimInterfaceHelloInterval Integer32, qtechPimInterfaceJoinPruneInterval Integer32, qtechPimInterfaceCBSRPreference Integer32, qtechPimInterfaceTrigHelloInterval Integer32, qtechPimInterfaceHelloHoldtime Integer32, qtechPimInterfaceLanPruneDelay INTEGER, qtechPimInterfacePropagationDelay Integer32, qtechPimInterfaceOverrideInterval Integer32, qtechPimInterfaceGenerationID INTEGER, qtechPimInterfaceJoinPruneHoldtime Integer32, qtechPimInterfaceGraftRetryInterval Integer32, qtechPimInterfaceMaxGraftRetries Integer32, qtechPimInterfaceSRTTLThreshold Integer32, qtechPimInterfaceLanDelayEnabled TruthValue, qtechPimInterfaceSRCapable TruthValue, qtechPimInterfaceDRPriority Integer32, qtechPimInterfaceNbrCounter Integer32, qtechPimInterfaceBsrBorderEnabled EnabledStatus, qtechPimInterfaceCountIn Integer32, qtechPimInterfaceCountOut Integer32, qtechPimInterfaceEnabled EnabledStatus, qtechPimNeighborFilterAcl DisplayString, qtechPimDrSupportAddressBound DisplayString } qtechPimInterfaceIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of this PIM interface." ::= { qtechPimInterfaceEntry 1 } qtechPimInterfaceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the PIM interface." ::= { qtechPimInterfaceEntry 2 } qtechPimInterfaceNetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The network mask for the IP address of the PIM interface." ::= { qtechPimInterfaceEntry 3 } qtechPimInterfaceMode OBJECT-TYPE SYNTAX INTEGER { dense(1), sparse(2), sparseDense(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The configured mode of this PIM interface. A value of sparseDense is only valid for PIMv1." DEFVAL { dense } ::= { qtechPimInterfaceEntry 4 } qtechPimInterfaceDR OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Designated Router on this PIM interface." ::= { qtechPimInterfaceEntry 5 } qtechPimInterfaceHelloInterval OBJECT-TYPE SYNTAX Integer32(0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The frequency at which PIM Hello messages are transmitted on this interface." DEFVAL { 30 } ::= { qtechPimInterfaceEntry 6 } qtechPimInterfaceJoinPruneInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The frequency at which PIM Join/Prune messages are transmitted on this PIM interface. The default value of this object is the pimJoinPruneInterval." ::= { qtechPimInterfaceEntry 7 } qtechPimInterfaceCBSRPreference OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface." DEFVAL { 0 } ::= { qtechPimInterfaceEntry 8 } qtechPimInterfaceTrigHelloInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time before a triggered PIM Hello message is transmitted on this interface." DEFVAL { 5 } ::= { qtechPimInterfaceEntry 9 } qtechPimInterfaceHelloHoldtime OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in the Holdtime field of Hello messages transmitted on this interface. This should be 3.5 times the value of pimInterfaceHelloInterval." DEFVAL { 105 } ::= { qtechPimInterfaceEntry 10 } qtechPimInterfaceLanPruneDelay OBJECT-TYPE SYNTAX INTEGER { off (2), on (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turns the LAN Prune Delay Option off and on on this interface." DEFVAL { off } ::= { qtechPimInterfaceEntry 11 } qtechPimInterfacePropagationDelay OBJECT-TYPE SYNTAX Integer32 (0..32767) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value inserted into the LAN Prune Delay field of a LAN Prune Delay option on this interface." DEFVAL { 500 } ::= { qtechPimInterfaceEntry 12 } qtechPimInterfaceOverrideInterval OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value inserted into the Override Interval field of a LAN Prune Delay option on this interface." DEFVAL { 2500 } ::= { qtechPimInterfaceEntry 13 } qtechPimInterfaceGenerationID OBJECT-TYPE SYNTAX INTEGER { off (2), on (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turns the Generation ID Option off and on on this interface." DEFVAL {off} ::= { qtechPimInterfaceEntry 14 } qtechPimInterfaceJoinPruneHoldtime OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value inserted into the Holdtime field of a Join/ Prune message sent on this interface. The value should be 3.5 times pimInterfaceJoinPruneInterval." DEFVAL { 210 } ::= { qtechPimInterfaceEntry 15 } qtechPimInterfaceGraftRetryInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The interval a PIM router waits for a Graft Ack before resending a Graft on this interface." DEFVAL { 3 } ::= { qtechPimInterfaceEntry 16 } qtechPimInterfaceMaxGraftRetries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of times this router will resend a Graft on this interface." DEFVAL { 2 } ::= { qtechPimInterfaceEntry 17 } qtechPimInterfaceSRTTLThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The Time To Live in a PIM-DM Refresh message at which it is not forwarded on this interface." DEFVAL { 0 } ::= { qtechPimInterfaceEntry 18 } qtechPimInterfaceLanDelayEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if all routers on this interface are using the LAN Prune Delay Option." ::= { qtechPimInterfaceEntry 19 } qtechPimInterfaceSRCapable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if all routers on this interface are using the State Refresh Capable Option." ::= { qtechPimInterfaceEntry 20 } qtechPimInterfaceDRPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The Designater Router Priority inserted into the DR priority option on this interface." DEFVAL { 1 } ::= { qtechPimInterfaceEntry 21 } qtechPimInterfaceNbrCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of interface's neighbour." ::= { qtechPimInterfaceEntry 22 } qtechPimInterfaceBsrBorderEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enabled means Define a PIM bootstrap message boundary for the PIM domain,use disabled to remove the PIM border." DEFVAL {disabled} ::= { qtechPimInterfaceEntry 23 } qtechPimInterfaceCountIn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets into the interface since the router has been up." ::= { qtechPimInterfaceEntry 24 } qtechPimInterfaceCountOut OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets out of the interface since the router has been up." ::= { qtechPimInterfaceEntry 25 } qtechPimInterfaceEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "use the ip pim command in interface configuration mode. To disable PIM on the interface, use the no form of this command." DEFVAL{disabled} ::= { qtechPimInterfaceEntry 26 } qtechPimNeighborFilterAcl OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the neighbor filter address list,which limits the scope of the neighbor,The default value means all neighbors will be allowed." DEFVAL{""} ::= { qtechPimInterfaceEntry 27} qtechPimDrSupportAddressBound OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the DR support address list,which limits the scope of the souce address ,this will be only used when the interface is DR, The default value means all souce address will be allowed." DEFVAL{""} ::= { qtechPimInterfaceEntry 28 } -- -- The PIM Neighbor Table -- qtechPimNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the router's PIM neighbors." ::= { qtechPim 3 } qtechPimNeighborEntry OBJECT-TYPE SYNTAX QtechPimNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the qtechPimNeighborTable." INDEX { qtechPimNeighborAddress } ::= { qtechPimNeighborTable 1 } QtechPimNeighborEntry ::= SEQUENCE { qtechPimNeighborAddress IpAddress, qtechPimNeighborIfIndex InterfaceIndex, qtechPimNeighborUpTime TimeTicks, qtechPimNeighborExpiryTime TimeTicks, qtechPimNeighborMode INTEGER, qtechPimNeighborLanPruneDelay Integer32, qtechPimNeighborOverrideInterval Integer32, qtechPimNeighborTBit Integer32, qtechPimNeighborSRCapable TruthValue, qtechPimNeighborDRPresent TruthValue } qtechPimNeighborAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the PIM neighbor for which this entry contains information." ::= { qtechPimNeighborEntry 1 } qtechPimNeighborIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The value of ifIndex for the interface used to reach this PIM neighbor." ::= { qtechPimNeighborEntry 2 } qtechPimNeighborUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time since this PIM neighbor (last) became a neighbor of the local router." ::= { qtechPimNeighborEntry 3 } qtechPimNeighborExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before this PIM neighbor will be aged out." ::= { qtechPimNeighborEntry 4 } qtechPimNeighborMode OBJECT-TYPE SYNTAX INTEGER { dense(1), sparse(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The active PIM mode of this neighbor. This object is deprecated for PIMv2 routers since all neighbors on the interface must be either dense or sparse as determined by the protocol running on the interface." ::= { qtechPimNeighborEntry 5 } qtechPimNeighborLanPruneDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of LAN Prune Delay field of the LAN Prune Delay Option received from this neighbor. A value of 0 indicates that no LAN Prune Delay Option was received from this neigbor." ::= { qtechPimNeighborEntry 6 } qtechPimNeighborOverrideInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of Override Interval field of the LAN Prune Delay Option received from this neighbor. A value of 0 indicates that no LAN Prune Delay Option was received from this neigbor." ::= { qtechPimNeighborEntry 7 } qtechPimNeighborTBit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the T bit field of the LAN Prune Delay Option received from this neighbor. The T bit specifies the ability of the neighbor to disable join suppression." ::= { qtechPimNeighborEntry 8 } qtechPimNeighborSRCapable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if this neighbor is using the State Refresh Capable Option." ::= { qtechPimNeighborEntry 9 } qtechPimNeighborDRPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if this neighbor is using the Designated Router Option." ::= { qtechPimNeighborEntry 10 } -- -- The PIM IP Multicast Route Table -- qtechPimIpMRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimIpMRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteTable defined in the IP Multicast MIB." ::= { qtechPim 4 } qtechPimIpMRouteEntry OBJECT-TYPE SYNTAX QtechPimIpMRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimIpMRouteTable. There is one entry per entry in the ipMRouteTable whose incoming interface is running PIM." INDEX { ipMRouteGroup, ipMRouteSource, ipMRouteSourceMask } ::= { qtechPimIpMRouteTable 1 } QtechPimIpMRouteEntry ::= SEQUENCE { qtechPimIpMRouteUpstreamAssertTimer TimeTicks, qtechPimIpMRouteAssertMetric Integer32, qtechPimIpMRouteAssertMetricPref Integer32, qtechPimIpMRouteAssertRPTBit TruthValue, qtechPimIpMRouteFlags INTEGER, qtechPimIpMRouteRPFNeighbor IpAddress, qtechPimIpMRouteSourceTimer TimeTicks, qtechPimIpMRouteOriginatorSRTTL Integer32 } qtechPimIpMRouteUpstreamAssertTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert has changed the upstream neighbor away from the RPF neighbor." ::= { qtechPimIpMRouteEntry 1 } qtechPimIpMRouteAssertMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received." ::= { qtechPimIpMRouteEntry 2 } qtechPimIpMRouteAssertMetricPref OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect." ::= { qtechPimIpMRouteEntry 3 } qtechPimIpMRouteAssertRPTBit OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect." ::= { qtechPimIpMRouteEntry 4 } qtechPimIpMRouteFlags OBJECT-TYPE SYNTAX INTEGER { rpt(0), spt(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes PIM-specific flags related to a multicast state entry. See the PIM Sparse Mode specification for the meaning of the RPT and SPT bits." ::= { qtechPimIpMRouteEntry 5 } qtechPimIpMRouteRPFNeighbor OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the current RPF neighbor. If there is an upstream Assert Winner, it will be the RPF neighbor. Otherwise, the RPF neighbor will be the next hop indicated by unicast routing." ::= { qtechPimIpMRouteEntry 6 } qtechPimIpMRouteSourceTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time before this router ceases originating State Refresh messages for this route." ::= { qtechPimIpMRouteEntry 7 } qtechPimIpMRouteOriginatorSRTTL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The TTL used in State Refresh messages originated by this router for this route." ::= { qtechPimIpMRouteEntry 8 } -- -- The PIM Next Hop Table -- qtechPimIpMRouteNextHopTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimIpMRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteNextHopTable defined in the IP Multicast MIB." ::= { qtechPim 5 } qtechPimIpMRouteNextHopEntry OBJECT-TYPE SYNTAX QtechPimIpMRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimIpMRouteNextHopTable. There is one entry per entry in the ipMRouteNextHopTable whose interface is running PIM and whose ipMRouteNextHopState is pruned(1)." INDEX { ipMRouteNextHopGroup, ipMRouteNextHopSource, ipMRouteNextHopSourceMask, ipMRouteNextHopIfIndex, ipMRouteNextHopAddress } ::= { qtechPimIpMRouteNextHopTable 1 } QtechPimIpMRouteNextHopEntry ::= SEQUENCE { qtechPimIpMRouteNextHopPruneReason INTEGER, qtechPimIpMRouteNextHopAssertWinner IpAddress, qtechPimIpMRouteNextHopAssertTimer TimeTicks, qtechPimIpMRouteNextHopAssertMetric Integer32, qtechPimIpMRouteNextHopAssertMetricPref Integer32, qtechPimIpMRouteNextHopJoinPruneTimer TimeTicks } qtechPimIpMRouteNextHopPruneReason OBJECT-TYPE SYNTAX INTEGER { other (1), prune (2), assert (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates why the downstream interface was pruned, whether in response to a PIM prune message or due to PIM Assert processing." ::= { qtechPimIpMRouteNextHopEntry 1 } qtechPimIpMRouteNextHopAssertWinner OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the Assert Winner." ::= { qtechPimIpMRouteNextHopEntry 2 } qtechPimIpMRouteNextHopAssertTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the PIM router leaves the current Assert state. A value of 0 indicates that the router is in the No Info state." ::= { qtechPimIpMRouteNextHopEntry 3 } qtechPimIpMRouteNextHopAssertMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric advertised by the Assert Winner." ::= { qtechPimIpMRouteNextHopEntry 4 } qtechPimIpMRouteNextHopAssertMetricPref OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric preference advertised by the Assert Winner." ::= { qtechPimIpMRouteNextHopEntry 5 } qtechPimIpMRouteNextHopJoinPruneTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the PIM router reverts to default operation on this interface. PIM-SM will cease forwarding, PIM-DM will resume forwarding." ::= { qtechPimIpMRouteNextHopEntry 6 } -- -- The PIM RP-Set Table -- qtechPimRPSetTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimRPSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, this information is obtained from received RP-Set messages." ::= { qtechPim 6 } qtechPimRPSetEntry OBJECT-TYPE SYNTAX QtechPimRPSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimRPSetTable." INDEX { qtechPimRPSetComponent, qtechPimRPSetGroupAddress, qtechPimRPSetGroupMask, qtechPimRPSetAddress } ::= { qtechPimRPSetTable 1 } QtechPimRPSetEntry ::= SEQUENCE { qtechPimRPSetGroupAddress IpAddress, qtechPimRPSetGroupMask IpAddress, qtechPimRPSetAddress IpAddress, qtechPimRPSetHoldTime Integer32, qtechPimRPSetExpiryTime TimeTicks, qtechPimRPSetComponent Integer32, qtechPimRPSetUpTime TimeTicks } qtechPimRPSetGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address which, when combined with pimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { qtechPimRPSetEntry 1 } qtechPimRPSetGroupMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast group address mask which, when combined with pimRPSetGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { qtechPimRPSetEntry 2 } qtechPimRPSetAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the Candidate-RP." ::= { qtechPimRPSetEntry 3 } qtechPimRPSetHoldTime OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The holdtime of a Candidate-RP." ::= { qtechPimRPSetEntry 4 } qtechPimRPSetExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the Candidate-RP will be declared down." ::= { qtechPimRPSetEntry 5 } qtechPimRPSetComponent OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION " A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value." ::= { qtechPimRPSetEntry 6 } qtechPimRPSetUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " Length of time that this rp has been up." ::= { qtechPimRPSetEntry 7 } -- -- The PIM Component Table -- qtechPimComponentTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing objects specific to a PIM domain. One row exists for each domain to which the router is connected. A PIM-SM domain is defined as an area of the network over which Bootstrap messages are forwarded. Typically, a PIM-SM router will be a member of exactly one domain. This table also supports, however, routers which may form a border between two PIM-SM domains and do not forward Bootstrap messages between them." ::= { qtechPim 7 } qtechPimComponentEntry OBJECT-TYPE SYNTAX QtechPimComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the starPimComponentTable." INDEX { qtechPimComponentIndex } ::= { qtechPimComponentTable 1 } QtechPimComponentEntry ::= SEQUENCE { qtechPimComponentIndex Integer32, qtechPimComponentBSRAddress IpAddress, qtechPimComponentBSRExpiryTime TimeTicks, qtechPimComponentCRPHoldTime Integer32, qtechPimComponentBSRUptime TimeTicks, qtechPimComponentBSRPriority Integer32, qtechPimComponentBSRHashMaskLength Integer32, qtechPimComponentBSRNextBsrMessage TimeTicks, qtechPimComponentNextCandRPAdv TimeTicks } qtechPimComponentIndex OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value. Routers that only support membership in a single PIM-SM domain should use a pimComponentIndex value of 1." ::= { qtechPimComponentEntry 1 } qtechPimComponentBSRAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the bootstrap router (BSR) for the local PIM region." ::= { qtechPimComponentEntry 2 } qtechPimComponentBSRExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the bootstrap router in the local domain will be declared down. For candidate BSRs, this is the time until the component sends an RP-Set message. For other routers, this is the time until it may accept an RP-Set message from a lower candidate BSR." ::= { qtechPimComponentEntry 3 } qtechPimComponentCRPHoldTime OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The holdtime of the component when it is a candidate RP in the local domain." ::= { qtechPimComponentEntry 4 } qtechPimComponentBSRUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Length of time that this router has been up." ::= { qtechPimComponentEntry 5 } qtechPimComponentBSRPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Priority of Bsr." ::= { qtechPimComponentEntry 6 } qtechPimComponentBSRHashMaskLength OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Length of a mask (32 bits maximum) that is to be ANDed with the group address before the hash function is called." ::= { qtechPimComponentEntry 7 } qtechPimComponentBSRNextBsrMessage OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time (in hours, minutes, and seconds) in which the next bootstrap message is due from this BSR." ::= { qtechPimComponentEntry 8 } qtechPimComponentNextCandRPAdv OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time (in hours, minutes, and seconds) in which the next candidate RP advertisement will be sent." ::= { qtechPimComponentEntry 9} -- -- PIM State Refresh Objects -- qtechPimSourceLifetime OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time this router will continue to originate State Refresh messages in the absence of traffic from the source itself." DEFVAL { 2100 } ::= { qtechPim 8 } qtechPimStateRefreshInterval OBJECT-TYPE SYNTAX Integer32 (1..255) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The interval between successive State Refresh messages originated by this router." DEFVAL { 60 } ::= { qtechPim 9 } qtechPimStateRefreshLimitInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This router will not forward successive State Refresh messages received at less than this interval." DEFVAL { 0 } ::= { qtechPim 10 } qtechPimStateRefreshTimeToLive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The TTL to be used by this router's originated State Refresh messages if the data packet's TTL is not recorded." DEFVAL { 16 } ::= { qtechPim 11 } qtechPimBsrCandidateGroup OBJECT IDENTIFIER ::= { qtechPim 12 } qtechPimBsrCandidateIfindex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Interface type and number on this router from which the bootstrap router address is derived, to make it a candidate. This interface must be enabled with Protocol Independent Multicast (PIM)." ::= { qtechPimBsrCandidateGroup 1 } qtechPimBsrCandidateHashMaskLength OBJECT-TYPE SYNTAX Integer32(0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "Length of a mask (32 bits maximum) that is to be ANDed with the group address before the hash function is called. All groups with the same seed hash (correspond) to the same RP. if qtechPimBsrCandidateIfindex is 0,then set this value is not valid." DEFVAL { 0 } ::= { qtechPimBsrCandidateGroup 2 } qtechPimBsrCandidatePriority OBJECT-TYPE SYNTAX Integer32(0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The BSR with the larger priority is preferred. If the priority values are the same, the router with the larger IP address is the BSR.if qtechPimBsrCandidateIfindex is 0,then set this value is not valid" DEFVAL { 0 } ::= { qtechPimBsrCandidateGroup 3 } qtechPimRPTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM version 2 information for the Rendezvous Points (RPs) for IP multicast groups." ::= { qtechPim 13 } qtechPimRPEntry OBJECT-TYPE SYNTAX QtechPimRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimRPTable." INDEX { qtechPimRPGroupAddress } ::= { qtechPimRPTable 1 } QtechPimRPEntry ::= SEQUENCE { qtechPimRPGroupAddress IpAddress, qtechPimRPAddress IpAddress, qtechPimRPExpiryTime TimeTicks, qtechPimRPNextRPReachableIn TimeTicks } qtechPimRPGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address which, when combined with pimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { qtechPimRPEntry 1 } qtechPimRPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the RP." ::= { qtechPimRPEntry 2 } qtechPimRPExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the RP will be declared down. If the local router is not the BSR, this value is 0." ::= { qtechPimRPEntry 3 } qtechPimRPNextRPReachableIn OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the time the next RP-reachable message will be sent. Time is expressed in hours:minutes:seconds." ::= { qtechPimRPEntry 4 } -- --static RP Table -- qtechPimStaticRPTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimStaticRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM version 2 information for the Rendezvous Points (RPs) for IP multicast groups." ::= { qtechPim 14 } qtechPimStaticRPEntry OBJECT-TYPE SYNTAX QtechPimStaticRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimStaticRPTable." INDEX { qtechPimStaticRPAddress } ::= { qtechPimStaticRPTable 1 } QtechPimStaticRPEntry ::= SEQUENCE { qtechPimStaticRPAddress IpAddress, qtechPimStaticRPAddressIsOverride EnabledStatus, qtechPimStaticRPAclName DisplayString, qtechPimStaticRPStatus RowStatus } qtechPimStaticRPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the RP." ::= { qtechPimStaticRPEntry 1 } qtechPimStaticRPAddressIsOverride OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates that if there is a conflict, the RP configured with this command prevails over the RP learned by Bsr-RP." DEFVAL { disabled } ::= { qtechPimStaticRPEntry 2 } qtechPimStaticRPAclName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of an access list that defines for which multicast groups the RP should be used,the default value means all groups should be used." DEFVAL { "" } ::= { qtechPimStaticRPEntry 3 } qtechPimStaticRPStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface." ::= {qtechPimStaticRPEntry 4} qtechPimRpCandidateTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechPimRpCandidateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the IP multicast groups for which the local router is to advertise itself as a Candidate-RP when the value of pimComponentCRPHoldTime is non-zero. If this table is empty, then the local router will advertise itself as a Candidate-RP for all groups (providing the value of pimComponentCRPHoldTime is non- zero)." ::= { qtechPim 15 } qtechPimRpCandidateEntry OBJECT-TYPE SYNTAX QtechPimRpCandidateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimRpCandidateTable." INDEX { qtechPimRpCandidateIfindex } ::= { qtechPimRpCandidateTable 1 } QtechPimRpCandidateEntry ::= SEQUENCE { qtechPimRpCandidateIfindex InterfaceIndex, qtechPimRpCandidateAclName DisplayString, qtechPimRpCandidateStatus RowStatus } qtechPimRpCandidateIfindex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address associated with this interface type and number is advertised as a candidate RP address." ::= { qtechPimRpCandidateEntry 1 } qtechPimRpCandidateAclName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The name of Acl list,that defines the group prefixes that are advertised in association with the RP address,the default value means all groups will be advertised in association with the RP address." DEFVAL { "" } ::= { qtechPimRpCandidateEntry 2 } qtechPimRpCandidateStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface." ::= {qtechPimRpCandidateEntry 3} -- PIM Traps qtechPimNeighborLoss NOTIFICATION-TYPE OBJECTS { qtechPimNeighborIfIndex } STATUS current DESCRIPTION "A pimNeighborLoss trap signifies the loss of an adjacency with a neighbor. This trap should be generated when the neighbor timer expires, and the router has no other neighbors on the same interface with a lower IP address than itself." ::= { qtechPimTraps 1 } -- compliance statements qtechPimMIBConformance OBJECT IDENTIFIER ::= { qtechPimMIB 2 } qtechPimMIBCompliances OBJECT IDENTIFIER ::= { qtechPimMIBConformance 1 } qtechPimMIBGroups OBJECT IDENTIFIER ::= { qtechPimMIBConformance 2 } qtechPimMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Qtech Pim MIB" MODULE -- this module MANDATORY-GROUPS { qtechPimMIBGroup } ::= { qtechPimMIBCompliances 1 } -- units of conformance qtechPimMIBGroup OBJECT-GROUP OBJECTS { qtechPimJoinPruneInterval, qtechPimInterfaceAddress, qtechPimInterfaceNetMask, qtechPimInterfaceMode, qtechPimInterfaceDR, qtechPimInterfaceHelloInterval, qtechPimInterfaceJoinPruneInterval, qtechPimInterfaceCBSRPreference, qtechPimInterfaceTrigHelloInterval, qtechPimInterfaceHelloHoldtime, qtechPimInterfaceLanPruneDelay, qtechPimInterfacePropagationDelay, qtechPimInterfaceOverrideInterval, qtechPimInterfaceGenerationID, qtechPimInterfaceJoinPruneHoldtime, qtechPimInterfaceGraftRetryInterval, qtechPimInterfaceMaxGraftRetries, qtechPimInterfaceSRTTLThreshold, qtechPimInterfaceLanDelayEnabled, qtechPimInterfaceSRCapable, qtechPimInterfaceDRPriority, qtechPimInterfaceNbrCounter, qtechPimInterfaceBsrBorderEnabled, qtechPimInterfaceCountIn, qtechPimInterfaceCountOut, qtechPimInterfaceEnabled, qtechPimNeighborFilterAcl, qtechPimDrSupportAddressBound, qtechPimNeighborIfIndex, qtechPimNeighborUpTime, qtechPimNeighborExpiryTime, qtechPimNeighborMode, qtechPimNeighborLanPruneDelay, qtechPimNeighborOverrideInterval, qtechPimNeighborTBit, qtechPimNeighborSRCapable, qtechPimNeighborDRPresent, qtechPimIpMRouteUpstreamAssertTimer, qtechPimIpMRouteAssertMetric, qtechPimIpMRouteAssertMetricPref, qtechPimIpMRouteAssertRPTBit, qtechPimIpMRouteFlags, qtechPimIpMRouteRPFNeighbor, qtechPimIpMRouteSourceTimer, qtechPimIpMRouteOriginatorSRTTL, qtechPimIpMRouteNextHopPruneReason, qtechPimIpMRouteNextHopAssertWinner, qtechPimIpMRouteNextHopAssertTimer, qtechPimIpMRouteNextHopAssertMetric, qtechPimIpMRouteNextHopAssertMetricPref, qtechPimIpMRouteNextHopJoinPruneTimer, qtechPimRPSetHoldTime, qtechPimRPSetExpiryTime, qtechPimRPSetUpTime, qtechPimComponentBSRAddress, qtechPimComponentBSRExpiryTime, qtechPimComponentCRPHoldTime, qtechPimComponentBSRUptime, qtechPimComponentBSRPriority, qtechPimComponentBSRHashMaskLength, qtechPimComponentBSRNextBsrMessage, qtechPimComponentNextCandRPAdv, qtechPimSourceLifetime, qtechPimStateRefreshInterval, qtechPimStateRefreshLimitInterval, qtechPimStateRefreshTimeToLive, qtechPimBsrCandidateIfindex, qtechPimBsrCandidateHashMaskLength, qtechPimBsrCandidatePriority, qtechPimRPAddress, qtechPimRPExpiryTime, qtechPimRPNextRPReachableIn, qtechPimStaticRPAddressIsOverride, qtechPimStaticRPAclName, qtechPimStaticRPStatus, qtechPimRpCandidateAclName, qtechPimRpCandidateStatus } STATUS current DESCRIPTION "A collection of objects providing pim management and opertion to a Qtech agent." ::= { qtechPimMIBGroups 1 } qtechPimNotifyGroup NOTIFICATION-GROUP NOTIFICATIONS { qtechPimNeighborLoss } STATUS current DESCRIPTION "The collection of objects which are used to specify notifications for pim." ::= { qtechPimMIBGroups 2 } END