-- =============================================================== -- Copyright (C) 2000 Paradyne Corporation. -- ATM M4 Extension Group PDN-ATMM4EXT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY , OBJECT-TYPE, OBJECT-IDENTITY, Gauge32, TimeTicks FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF pdnAtm FROM PDN-HEADER-MIB atmfM4VpTestEntry, atmfM4VcTestEntry, atmfM4TcProtoCurrEntry, atmfM4TcProtoHistEntry FROM ATM-FORUM-SNMP-M4-MIB ifIndex FROM IF-MIB; -- =============================================================== -- -- Extentions to the ATM Forum M4 Mib -- -- =============================================================== pdnAtmfM4ExtMIB MODULE-IDENTITY LAST-UPDATED "200103080000Z" ORGANIZATION "Paradyne Corporation MIB Working Group" CONTACT-INFO "Paradyne Corporation 8545 126th Avenue North Largo, FL 33773 www.paradyne.com General Comments to: mibwg_team@eng.paradyne.com" DESCRIPTION "This MIB Module extends the ATM-FORUM-SNMP-M4-MI defined in the Atm Forums M4 Mib " REVISION "200208150000Z" DESCRIPTION "P. Easwar o Added New Table pdnAtmfM4VpLoopbackTestTable. " REVISION "200103080000Z" DESCRIPTION "R.A.Bowhall o Added error code of adminStatusDisabled(8). " REVISION "200009260000Z" DESCRIPTION "R. Steinberger o Added size to pdnAtmfM4Vc1CellLoopReportedLocation. " REVISION "200009220000Z" DESCRIPTION "R. Steinberger o Added error code of testTimeOut(7). o Added description of use of pdnAtmfM4Vc1CellLoopTable o Changed pdnAtmfM4Vc1CellLoopReportedLocation type to meet actual M4 definition of OCTET STRING(SIZE(16)) o Added the pdnAtmfM4LoopbackLocationTable " REVISION "200009210000Z" DESCRIPTION "J.Strain o Added E2E and SEG as Multiple OAM Cell Tests o documented mapping of atmfM4VcTestType to the corresponding atmfM4VcTestCode results table " REVISION "200009080000Z" DESCRIPTION "R. Steinberger o Cleaned tabs throughout document. o Fixed naming convention. o Added pdnAtmfM4Vc1CellLoopTable for ATM OAM loopbacks that send only single test cell. o Added conformance section. " REVISION "200006290000Z" DESCRIPTION "Z. Pan o added augmented atmfM4VcTestTable for ATM OAM loopback test. " ::= { pdnAtm 6 } pdnAtmfM4ExtObjects OBJECT IDENTIFIER ::= { pdnAtmfM4ExtMIB 1 } pdnAtmfM4ExtTraps OBJECT IDENTIFIER ::= { pdnAtmfM4ExtMIB 2 } pdnAtmfM4ExtConformance OBJECT IDENTIFIER ::= { pdnAtmfM4ExtMIB 3 } pdnAtmfM4ExtTrapPrefix OBJECT IDENTIFIER ::= { pdnAtmfM4ExtTraps 0 } -- -- Textual Conventions Specific to this MIB Module -- PdnAtmfM4TestErrorCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The specific error codes related to attempting to run a test. The codes have the following meanings: noError(0) -- No Error Occurred badIfIndex(1) -- Specified interface does not exist noVccFound(2) -- The Vcc does not exist on the interface notOwner(3) -- Not the current owner of the test noResourceAvailable(4) -- Device memory allocation failure noLoopbackAllocated(5) -- Could not start the test testCompleted(6) -- Test completed or stopped normally testTimeOut(7) -- Test unsuccessfully due to timeout adminStatusDisabled(8) -- ifAdminStatus is Disabled " SYNTAX INTEGER { noError(0), badIfIndex(1), noVccFound(2), notOwner(3), noResourceAvailable(4), noLoopbackAllocated(5), testCompleted(6), testTimeOut(7), adminStatusDisabled(8) } -- -- ATM TC layer current and historical fifteen-minute interval statistics -- pdnAtmfM4TcProtoCurrExtTable and pdnAtmfM4TcProtoHistExtTable -- -- ATM TC layer current fifteen-minute interval data statistics pdnAtmfM4TcProtoCurrExtTable OBJECT-TYPE SYNTAX SEQUENCE OF PdnAtmfM4TcProtoCurrExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Paradyne Extension to the atmfM4TcProtoCurrTable of the ATM-FORUM-SNMP-M4-MIB." ::= { pdnAtmfM4ExtObjects 1 } pdnAtmfM4TcProtoCurrExtEntry OBJECT-TYPE SYNTAX PdnAtmfM4TcProtoCurrExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Paradyne Extension to the atmfM4TcProtoCurrTable of the ATM-FORUM-SNMP-M4-MIB." AUGMENTS { atmfM4TcProtoCurrEntry } ::= { pdnAtmfM4TcProtoCurrExtTable 1 } PdnAtmfM4TcProtoCurrExtEntry ::= SEQUENCE { pdnAtmfM4TcProtoCurrCellIns Gauge32, pdnAtmfM4TcProtoCurrCellOuts Gauge32, pdnAtmfM4TcProtoCurrInDiscards Gauge32, pdnAtmfM4TcProtoCurrOutDiscards Gauge32, pdnAtmfM4TcProtoCurrLCDEvents Gauge32, pdnAtmfM4TcProtoCurrUnknownCells Gauge32, pdnAtmfM4TcProtoCurrCorrectedHEC Gauge32 } pdnAtmfM4TcProtoCurrCellIns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells received on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoCurrExtEntry 1 } pdnAtmfM4TcProtoCurrCellOuts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells sent on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoCurrExtEntry 2 } pdnAtmfM4TcProtoCurrInDiscards OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RX ATM cells dropped on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoCurrExtEntry 3 } pdnAtmfM4TcProtoCurrOutDiscards OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of TX ATM cells dropped on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoCurrExtEntry 4 } pdnAtmfM4TcProtoCurrLCDEvents OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Loss of Cell Delineation (LCD) event occurred on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoCurrExtEntry 5 } pdnAtmfM4TcProtoCurrUnknownCells OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of unknown Cells received on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoCurrExtEntry 6 } pdnAtmfM4TcProtoCurrCorrectedHEC OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Cell with corrected HEC received on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoCurrExtEntry 7 } -- -- ATM TC layer historical fifteen-minute interval statistics -- (per interface and time interval) -- pdnAtmfM4TcProtoHistExtTable OBJECT-TYPE SYNTAX SEQUENCE OF PdnAtmfM4TcProtoHistExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Paradyne Extension to the atmfM4TcProtoHistTable of the ATM-FORUM-SNMP-M4-MIB." ::= { pdnAtmfM4ExtObjects 2 } pdnAtmfM4TcProtoHistExtEntry OBJECT-TYPE SYNTAX PdnAtmfM4TcProtoHistExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Paradyne Extension to the atmfM4TcProtoHistTable of the ATM-FORUM-SNMP-M4-MIB." AUGMENTS { atmfM4TcProtoHistEntry } ::= { pdnAtmfM4TcProtoHistExtTable 1 } PdnAtmfM4TcProtoHistExtEntry ::= SEQUENCE { pdnAtmfM4TcProtoHistCellIns Gauge32, pdnAtmfM4TcProtoHistCellOuts Gauge32, pdnAtmfM4TcProtoHistInDiscards Gauge32, pdnAtmfM4TcProtoHistOutDiscards Gauge32, pdnAtmfM4TcProtoHistLCDEvents Gauge32, pdnAtmfM4TcProtoHistUnknownCells Gauge32, pdnAtmfM4TcProtoHistCorrectedHEC Gauge32 } pdnAtmfM4TcProtoHistCellIns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells received on this interface during this interval" ::= { pdnAtmfM4TcProtoHistExtEntry 1 } pdnAtmfM4TcProtoHistCellOuts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells sent on this interface during this interval" ::= { pdnAtmfM4TcProtoHistExtEntry 2 } pdnAtmfM4TcProtoHistInDiscards OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RX ATM cells dropped on this interface during this interval" ::= { pdnAtmfM4TcProtoHistExtEntry 3 } pdnAtmfM4TcProtoHistOutDiscards OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of TX ATM cells dropped on this interface during this interval" ::= { pdnAtmfM4TcProtoHistExtEntry 4 } pdnAtmfM4TcProtoHistLCDEvents OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Loss of Cell Delineation (LCD) event occurred on this interface during this interval" ::= { pdnAtmfM4TcProtoHistExtEntry 5 } pdnAtmfM4TcProtoHistUnknownCells OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of unknown Cells received on this interface since the start of this interval" ::= { pdnAtmfM4TcProtoHistExtEntry 6 } pdnAtmfM4TcProtoHistCorrectedHEC OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Cell with corrected HEC received on this interface during this interval" ::= { pdnAtmfM4TcProtoHistExtEntry 7 } -- -- The following object defines a group of OAM test types. -- This group is to contain any Paradyne Specific OAM test -- pdnAtmfM4TestTypes OBJECT IDENTIFIER ::= { pdnAtmfM4ExtObjects 3 } -- -- The following OID is defined to initiate continuous Segment OAM Cells -- pdnAtmfM4TestOAMLoopbackSegMultiCell OBJECT-IDENTITY STATUS current DESCRIPTION "This identifies an OAM Loopback Test on a VPL, VPC, VCL, or VCC termination point, using a segment OAM cell. The test type must have appended to it a code that uniquely identifies an intermediate point responsible for looping back the cell. If this is absent, the loopback is performed at the end of the segment or connection. E.g., the OID { pdnAtmfM4TestOAMLoopbackSegMultiCell 5 } identifies that the loopback should be performed at the intermediate point labeled 5." ::= { pdnAtmfM4TestTypes 1 } -- -- The following OID is defined to initiate continuous End to End OAM cells -- pdnAtmfM4TestOAMLoopbackE2EMultiCell OBJECT-IDENTITY STATUS current DESCRIPTION "This identifies an OAM Loopback Test on a VPL, VPC, VCL, or VCC termination point, using an end-to-end OAM cell." ::= { pdnAtmfM4TestTypes 2 } -- -- Test Code to Test Results Matrix -- -- atmfM4VcTestType atmfM4VcTestCode Result Table -- ________________ _____________________________ -- -- atmfM4TestOAMLoopbackSeg(standard is a single cell test) -- pdnAtmfM4Vc1CellLoopTable -- atmfM4TestOAMLoopbackE2E(standard is a single cell test) -- pdnAtmfM4Vc1CellLoopTable -- -- pdnAtmfM4TestOAMLoopbackSegMultiCell -- pdnAtmfM4VcLoopbackTestTable -- pdnAtmfM4TestOAMLoopbackE2EMultiCell -- pdnAtmfM4VcLoopbackTestTable -- -- -- OAM Loopback test (multiple cell) detailed results table -- pdnAtmfM4VcLoopbackTestTable OBJECT-TYPE SYNTAX SEQUENCE OF PdnAtmfM4VcLoopbackTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains input and results for OAM loopback tests. There can be only one test running per ATM VCC This table should be used in conjunction with atmfM4VcTestTable with all the semantics of atmfM4VcTestTable." ::= { pdnAtmfM4ExtObjects 4 } pdnAtmfM4VcLoopbackTestEntry OBJECT-TYPE SYNTAX PdnAtmfM4VcLoopbackTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing objects for test results for ATM OAM loopback test" AUGMENTS { atmfM4VcTestEntry } ::= { pdnAtmfM4VcLoopbackTestTable 1 } PdnAtmfM4VcLoopbackTestEntry ::= SEQUENCE { pdnAtmfM4VcLoopbackTestElpsTime TimeTicks, pdnAtmfM4VcLoopbackTestCellsSent Gauge32, pdnAtmfM4VcLoopbackTestCellsRcvd Gauge32, pdnAtmfM4VcLoopbackTestMinRTDelay Gauge32, pdnAtmfM4VcLoopbackTestMaxRTDelay Gauge32, pdnAtmfM4VcLoopbackTestAvgRTDelay Gauge32, pdnAtmfM4VcLoopbackTestErrorCode PdnAtmfM4TestErrorCode } pdnAtmfM4VcLoopbackTestElpsTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the time that has elapsed since the test started." ::= { pdnAtmfM4VcLoopbackTestEntry 1 } pdnAtmfM4VcLoopbackTestCellsSent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a count of the number of test cells that have been sent. The value of this object stops increasing when it reaches its maximum value." ::= { pdnAtmfM4VcLoopbackTestEntry 2 } pdnAtmfM4VcLoopbackTestCellsRcvd OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a count of the number of test cells that have been received. The value of this object stops increasing when it reaches its maximum value." ::= { pdnAtmfM4VcLoopbackTestEntry 3 } pdnAtmfM4VcLoopbackTestMinRTDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the shortest round trip delay since the test has been started. It is calculated only on the cells that have been received. Cells that were dropped are not counted." ::= { pdnAtmfM4VcLoopbackTestEntry 4 } pdnAtmfM4VcLoopbackTestMaxRTDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the longest round trip delay since the test has been started. It is calculated only on the cells that have been received. Cells that were dropped are not counted." ::= { pdnAtmfM4VcLoopbackTestEntry 5 } pdnAtmfM4VcLoopbackTestAvgRTDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the average round trip delay since the test has been started. It is calculated only on the cells that have been received. Cells that were dropped are not counted." ::= { pdnAtmfM4VcLoopbackTestEntry 6 } pdnAtmfM4VcLoopbackTestErrorCode OBJECT-TYPE SYNTAX PdnAtmfM4TestErrorCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the specific error code on the test result." ::= { pdnAtmfM4VcLoopbackTestEntry 7 } -- -- Single Cell OAM Loopback test detailed results -- -- This table contains results for single cell OAM tests that are not -- of a broadcast variety. -- -- Recommended Use: -- -- 1) The NMS will start a test using the M4 MIB's atmfM4VcTestTable. -- 2) Upon starting the test, the agent will put the corresponding OID -- of a row in this table into the atmfM4VcTestCode object. -- 3) When the value of atmfM4VcTestResult is not equal to inProgress(3), -- the values contained in this table should be read. -- pdnAtmfM4Vc1CellLoopTable OBJECT-TYPE SYNTAX SEQUENCE OF PdnAtmfM4Vc1CellLoopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains input and results for single cell OAM loopback tests. There can be only one test running per ATM VCC This table should be used in conjunction with atmfM4VcTestTable with all the semantics of atmfM4VcTestTable." ::= { pdnAtmfM4ExtObjects 5 } pdnAtmfM4Vc1CellLoopEntry OBJECT-TYPE SYNTAX PdnAtmfM4Vc1CellLoopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing objects for test results for a single cell ATM OAM loopback test" AUGMENTS { atmfM4VcTestEntry } ::= { pdnAtmfM4Vc1CellLoopTable 1 } PdnAtmfM4Vc1CellLoopEntry ::= SEQUENCE { pdnAtmfM4Vc1CellLoopRTDelay Gauge32, pdnAtmfM4Vc1CellLoopReportedLocation OCTET STRING, pdnAtmfM4Vc1CellLoopErrorCode PdnAtmfM4TestErrorCode } pdnAtmfM4Vc1CellLoopRTDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the round trip delay of the the test cell. A value of zero indicates that no cell has been received." ::= { pdnAtmfM4Vc1CellLoopEntry 1 } pdnAtmfM4Vc1CellLoopReportedLocation OBJECT-TYPE SYNTAX OCTET STRING(SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the location identifier reported by the received cell." ::= { pdnAtmfM4Vc1CellLoopEntry 2 } pdnAtmfM4Vc1CellLoopErrorCode OBJECT-TYPE SYNTAX PdnAtmfM4TestErrorCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the specific error code on the test result." ::= { pdnAtmfM4Vc1CellLoopEntry 3 } -- -- OAM Segment Loopback Location Code -- pdnAtmfM4LoopbackLocationTable OBJECT-TYPE SYNTAX SEQUENCE OF PdnAtmfM4LoopbackLocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the ATM OAM loopback location codes for ATM cell layer interfaces." ::= { pdnAtmfM4ExtObjects 6 } pdnAtmfM4LoopbackLocationEntry OBJECT-TYPE SYNTAX PdnAtmfM4LoopbackLocationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing objects for ATM OAM loopback locations." INDEX { ifIndex } ::= { pdnAtmfM4LoopbackLocationTable 1 } PdnAtmfM4LoopbackLocationEntry ::= SEQUENCE { pdnAtmfM4LoopbackLocationCode OCTET STRING } pdnAtmfM4LoopbackLocationCode OBJECT-TYPE SYNTAX OCTET STRING(SIZE(16)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the value of ATM OAM Loopback Location Code" ::= { pdnAtmfM4LoopbackLocationEntry 1 } pdnAtmfM4VpLoopbackTestTable OBJECT-TYPE SYNTAX SEQUENCE OF PdnAtmfM4VpLoopbackTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains input and results for OAM loopback tests. There can be only one test running per ATM VPC This table should be used in conjunction with atmfM4VpTestTable with all the semantics of atmfM4VpTestTable." ::= { pdnAtmfM4ExtObjects 7 } pdnAtmfM4VpLoopbackTestEntry OBJECT-TYPE SYNTAX PdnAtmfM4VpLoopbackTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing objects for test results for ATM OAM loopback test" AUGMENTS { atmfM4VpTestEntry } ::= { pdnAtmfM4VpLoopbackTestTable 1 } PdnAtmfM4VpLoopbackTestEntry ::= SEQUENCE { pdnAtmfM4VpLoopbackTestElpsTime TimeTicks, pdnAtmfM4VpLoopbackTestCellsSent Gauge32, pdnAtmfM4VpLoopbackTestCellsRcvd Gauge32, pdnAtmfM4VpLoopbackTestMinRTDelay Gauge32, pdnAtmfM4VpLoopbackTestMaxRTDelay Gauge32, pdnAtmfM4VpLoopbackTestAvgRTDelay Gauge32, pdnAtmfM4VpLoopbackTestErrorCode PdnAtmfM4TestErrorCode } pdnAtmfM4VpLoopbackTestElpsTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the time that has elapsed since the test started." ::= { pdnAtmfM4VpLoopbackTestEntry 1 } pdnAtmfM4VpLoopbackTestCellsSent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a count of the number of test cells that have been sent. The value of this object stops increasing when it reaches its maximum value." ::= { pdnAtmfM4VpLoopbackTestEntry 2 } pdnAtmfM4VpLoopbackTestCellsRcvd OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies a count of the number of test cells that have been received. The value of this object stops increasing when it reaches its maximum value." ::= { pdnAtmfM4VpLoopbackTestEntry 3 } pdnAtmfM4VpLoopbackTestMinRTDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the shortest round trip delay since the test has been started. It is calculated only on the cells that have been received. Cells that were dropped are not counted." ::= { pdnAtmfM4VpLoopbackTestEntry 4 } pdnAtmfM4VpLoopbackTestMaxRTDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the longest round trip delay since the test has been started. It is calculated only on the cells that have been received. Cells that were dropped are not counted." ::= { pdnAtmfM4VpLoopbackTestEntry 5 } pdnAtmfM4VpLoopbackTestAvgRTDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the average round trip delay since the test has been started. It is calculated only on the cells that have been received. Cells that were dropped are not counted." ::= { pdnAtmfM4VpLoopbackTestEntry 6 } pdnAtmfM4VpLoopbackTestErrorCode OBJECT-TYPE SYNTAX PdnAtmfM4TestErrorCode MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the specific error code on the test result." ::= { pdnAtmfM4VpLoopbackTestEntry 7 } -- Conformance Information pdnAtmfM4Groups OBJECT IDENTIFIER ::= { pdnAtmfM4ExtConformance 1 } pdnAtmfM4Compliances OBJECT IDENTIFIER ::= { pdnAtmfM4ExtConformance 2 } pdnAtmfM4Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which support the ATM M4 extensions." MODULE GROUP pdnAtmfM4LoopbackLocationGroup DESCRIPTION "The conditional objects in the Loopback Location Group." OBJECT pdnAtmfM4LoopbackLocationCode MIN-ACCESS read-only DESCRIPTION "Write access is not required" ::= { pdnAtmfM4Compliances 1 } -- -- Units of Conformance -- pdnAtmfM4TcCurrGroup OBJECT-GROUP OBJECTS { pdnAtmfM4TcProtoCurrCellIns, pdnAtmfM4TcProtoCurrCellOuts, pdnAtmfM4TcProtoCurrInDiscards, pdnAtmfM4TcProtoCurrOutDiscards, pdnAtmfM4TcProtoCurrLCDEvents, pdnAtmfM4TcProtoCurrUnknownCells, pdnAtmfM4TcProtoCurrCorrectedHEC } STATUS current DESCRIPTION "The objects in the ATM TC layer current table." ::= { pdnAtmfM4Groups 1 } pdnAtmfM4TcHistGroup OBJECT-GROUP OBJECTS { pdnAtmfM4TcProtoHistCellIns, pdnAtmfM4TcProtoHistCellOuts, pdnAtmfM4TcProtoHistInDiscards, pdnAtmfM4TcProtoHistOutDiscards, pdnAtmfM4TcProtoHistLCDEvents, pdnAtmfM4TcProtoHistUnknownCells, pdnAtmfM4TcProtoHistCorrectedHEC } STATUS current DESCRIPTION "The objects in the ATM TC layer history table." ::= { pdnAtmfM4Groups 2 } pdnAtmfM4VcLoopbackTestGroup OBJECT-GROUP OBJECTS { pdnAtmfM4VcLoopbackTestElpsTime, pdnAtmfM4VcLoopbackTestCellsSent, pdnAtmfM4VcLoopbackTestCellsRcvd, pdnAtmfM4VcLoopbackTestMinRTDelay, pdnAtmfM4VcLoopbackTestMaxRTDelay, pdnAtmfM4VcLoopbackTestAvgRTDelay, pdnAtmfM4VcLoopbackTestErrorCode } STATUS current DESCRIPTION "The objects in the ATM OAM Loopback Test (multiple cell) table for ATM VCC." ::= { pdnAtmfM4Groups 3 } pdnAtmfM4Vc1CellLoopGroup OBJECT-GROUP OBJECTS { pdnAtmfM4Vc1CellLoopRTDelay, pdnAtmfM4Vc1CellLoopReportedLocation, pdnAtmfM4Vc1CellLoopErrorCode } STATUS current DESCRIPTION "The objects in the ATM Single Cell OAM Loopback Test table." ::= { pdnAtmfM4Groups 4 } pdnAtmfM4LoopbackLocationGroup OBJECT-GROUP OBJECTS { pdnAtmfM4LoopbackLocationCode } STATUS current DESCRIPTION "The objects in the ATM Loopback Location table." ::= { pdnAtmfM4Groups 5 } pdnAtmfM4VpLoopbackTestGroup OBJECT-GROUP OBJECTS { pdnAtmfM4VpLoopbackTestElpsTime, pdnAtmfM4VpLoopbackTestCellsSent, pdnAtmfM4VpLoopbackTestCellsRcvd, pdnAtmfM4VpLoopbackTestMinRTDelay, pdnAtmfM4VpLoopbackTestMaxRTDelay, pdnAtmfM4VpLoopbackTestAvgRTDelay, pdnAtmfM4VpLoopbackTestErrorCode } STATUS current DESCRIPTION "The objects in the ATM OAM Loopback Test (multiple cell) table for ATM VPC." ::= { pdnAtmfM4Groups 6 } END