--=========================================================== -- Copyright (c) 2010-2013 Hewlett-Packard Development Company, L.P. -- Description: This MIB is excerpted from the draft-ietf-hubmib-efm-epon-mib-02 directly --- only changed the object name,added the hpnicf as prefix. -- Reference: -- Version: V1.0 -- History: -- V1.0 created by liyue. -- Define MODULE-IDENTITY for hpnicfEponDeviceMIB --================================================================= HPN-ICF-EPON-DEVICE-MIB DEFINITIONS ::= BEGIN IMPORTS hpnicfEpon FROM HPN-ICF-OID-MIB MODULE-IDENTITY, mib-2, OBJECT-TYPE, Counter32, Unsigned32, Integer32, zeroDotZero FROM SNMPv2-SMI TruthValue, DateAndTime, RowStatus, MacAddress FROM SNMPv2-TC ifIndex FROM IF-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB; hpnicfEponDeviceMIB MODULE-IDENTITY LAST-UPDATED "200409210000Z" -- September 21, 2004 ORGANIZATION "" CONTACT-INFO "" DESCRIPTION "The objects in this MIB module are used to manage Ethernet Passive Optical Network (EPON) devices which are based on the Ethernet in the First Mile (EFM) PON as defined in IEEE Draft P802.3ah/D3.0 clause 60,64,65. This MIB is excerpted from the draft files directly,only changed the object name,added the hpnicf as prefix. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Draft P802.3ah/D3.3: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', 22 April 2004. Of particular interest are Clause 64(MPCP) 65(P2mP RS) and 60 (PON PMDs). Clause 30, 'Management', and Clause 45,'Management Data Input/Output (MDIO) Interface'. Copyright (C) The Internet Society (2004). This version of this MIB module is part of XXXX see the RFC itself for full legal notices." -- Editor's Note: Replace XXXX with the actual RFC number -- assigned by RFC Editor and remove this note REVISION "200409210000Z" -- September 21, 2004 DESCRIPTION "Initial version, published as RFC XXXX." ::= { hpnicfEpon 4 } -- Editor's Note: Replace XXX with a real OID once it is -- assigned by IANA and remove this note. hpnicfEponDeviceObjectMIB OBJECT IDENTIFIER ::= { hpnicfEponDeviceMIB 1 } hpnicfEponDeviceObjects OBJECT IDENTIFIER ::= { hpnicfEponDeviceObjectMIB 1 } hpnicfEponDeviceConformance OBJECT IDENTIFIER ::= { hpnicfEponDeviceObjectMIB 2 } hpnicfEponDeviceControlObjects OBJECT IDENTIFIER ::= { hpnicfEponDeviceObjects 1 } hpnicfEponDeviceStatObjects OBJECT IDENTIFIER ::= { hpnicfEponDeviceObjects 2 } hpnicfEponDeviceEventObjects OBJECT IDENTIFIER ::= { hpnicfEponDeviceObjects 3 } hpnicfEponDeviceControlTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfEponDeviceControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for EPON device MIB modules." ::= { hpnicfEponDeviceControlObjects 1 } hpnicfEponDeviceControlEntry OBJECT-TYPE SYNTAX HpnicfEponDeviceControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EPON device Control table." INDEX { ifIndex } ::= { hpnicfEponDeviceControlTable 1 } HpnicfEponDeviceControlEntry ::= SEQUENCE { hpnicfEponDeviceObjectReset INTEGER, hpnicfEponDeviceObjectModes INTEGER, hpnicfEponDeviceObjectFecEnabled INTEGER, hpnicfEponDeviceObjectOamMode INTEGER, hpnicfEponDeviceObjectDeviceReadyMode INTEGER, hpnicfEponDeviceObjectPowerDown TruthValue, hpnicfEponDeviceObjectNumberOfLLIDs Integer32, hpnicfEponDeviceObjectReportThreshold Integer32, hpnicfEponDeviceRemoteMACAddressLLIDControl INTEGER } hpnicfEponDeviceObjectReset OBJECT-TYPE SYNTAX INTEGER { running(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to reset the EPON device. The interface may be unavailable while the reset occurs and data may be lost. During reading operation it returns the state of the EPON device. running(1) indicates and operates normal operation, reset(2) indicates and operates reset mode. Writing can be done all the time." DEFVAL { 1 } ::= { hpnicfEponDeviceControlEntry 1 } hpnicfEponDeviceObjectModes OBJECT-TYPE SYNTAX INTEGER { olt(1), onu(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable defines the mode of the EPON device. When an olt(1) it is an Optical Line Terminal device (server) and when an onu(2) and Optical Network Unit device (client)" ::= { hpnicfEponDeviceControlEntry 2 } hpnicfEponDeviceObjectFecEnabled OBJECT-TYPE SYNTAX INTEGER { noFecEnabled (1), fecTxEnabled (2), fecRxEnabled (3), fecTxRxEnabled (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable defines and provides information whether the EPON device uses FEC as defined in the [802.3ah] clause 65.2 for EPON. When noFECEnabled(1) the device does not support FEC mode When fecTxEnabled(2) the device supports the FEC transmission mode. When fecRxEnabled(3) the device supports the FEC Receive mode. When fecTxRxEnabled(4) the device supports the FEC transmission and receive mode. Writing can be done all the time. This attribute is relevant for an OLT and an ONU." DEFVAL { 1 } ::= { hpnicfEponDeviceControlEntry 4 } hpnicfEponDeviceObjectOamMode OBJECT-TYPE SYNTAX INTEGER { noOam (1), oamServer (2), oamclient (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable defines and provides information on the Operation Administration and Maintenance (OAM) mode of an EPON device as defined by the [802.3ah] clause 57. When noOam(1) the device does not supports the OAM mode. When oamServer(2) the device supports the OAM mode as a server unit. When oamClient(3) the device supports the OAM mode as a client unit. Writing can be done during initialization, hpnicfEponDeviceObjectDeviceReadyMode is in notReady(1) or inProcess(2). This attribute is relevant for an OLT and an ONU." DEFVAL { 1 } ::= { hpnicfEponDeviceControlEntry 5 } hpnicfEponDeviceObjectDeviceReadyMode OBJECT-TYPE SYNTAX INTEGER { notReady (1), inProcess (2), ready (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable defines the mode of an EPON device and provides information on the mode in initialization - ready for registration as defined by the [802.3ah] clause 64. When notReady(1) the device is not ready for operation. When inProcess(2) the device is in initialization process. When ready(3) the device is ready for registration. Writing can be done all the time. This attribute is relevant for an OLT and an ONU." DEFVAL { 1 } ::= { hpnicfEponDeviceControlEntry 6 } hpnicfEponDeviceObjectPowerDown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this variable to True(1) will cause Device to be entered into Power down mode where no registration is allowed and only receiving data from the link. Writing can be done all the time. This attribute is relevant for an OLT and an ONU." DEFVAL { false } ::= { hpnicfEponDeviceControlEntry 7 } hpnicfEponDeviceObjectNumberOfLLIDs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read only variable which defines the number of registered LLIDs (as defined by the [802.3ah] clause 65) in a EPON network for an OLT and an ONU. Initialization value is 0. This attribute is relevant for an OLT and an ONU." ::= { hpnicfEponDeviceControlEntry 8 } hpnicfEponDeviceObjectReportThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "TQ (16nsec)" MAX-ACCESS read-write STATUS current DESCRIPTION "A set of 8 integers, for each LLID, that defines the threshold reporting for each Queue in the REPORT message, as defined in [802.3ah] 64. First Queue set reporting will provide information on the queue occupancy of frames below this Threshold. The value returned shall be in Time quanta (TQ) which is 16nsec or 2 octets increments. Writing can be done all the time. This attribute is relevant for an OLT and an ONU." DEFVAL { 0 } ::= { hpnicfEponDeviceControlEntry 9 } hpnicfEponDeviceRemoteMACAddressLLIDControl OBJECT-TYPE SYNTAX INTEGER { none(1), resetLog(2), useDefaultReporting(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates and controls the resetting of the LLID MAC address log. Setting this object to none(1) has no action resetLog(2) empties the LLID MAC address log. All data is deleted. Setting it to useDefaultReporting(3) returns all entries priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3)." DEFVAL { 3 } ::= { hpnicfEponDeviceControlEntry 10 } hpnicfEponDeviceRemoteMACAddressLLIDTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfEponDeviceRemoteMACAddressLLIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of read-only value that identifies the source_address and LLIDs parameter of the remote devices in the network. This MacAddress value, as defined in [802.3ah], 30.3.5.1.5, is updated on reception of a valid frame with a unicast destination Field or (1) a destination Field equal to the reserved multicast address for MAC Control specified in [802.3ah] Annex 31A, (2) lengthOrType field value equal to the reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3)an MPCP subtype value equal to the subtype reserved for MPCP as specified in [802.3ah] Annex 31A, and an LLID as allocated by the OLT. The table is defined as Remote MAC address - LLID (RMadL) The table is relevant only for an OLT device, and is equivalent from a bridge emulation to the bridge port-MAC address table where the LLIDs are equivalent to virtual bridge ports." ::= { hpnicfEponDeviceControlObjects 2 } hpnicfEponDeviceRemoteMACAddressLLIDEntry OBJECT-TYPE SYNTAX HpnicfEponDeviceRemoteMACAddressLLIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A group of entries. Applications create and delete entries using hpnicfEponDeviceRMadlEntryStatus. When adding objects to an LLID they are added in the persistent order of their index in this table." INDEX {ifIndex } ::= { hpnicfEponDeviceRemoteMACAddressLLIDTable 1 } HpnicfEponDeviceRemoteMACAddressLLIDEntry ::= SEQUENCE { hpnicfEponDeviceRemoteMACAddressLLIDName SnmpAdminString, hpnicfEponDeviceRMadlLLID Unsigned32, hpnicfEponDeviceRMadlLogID OBJECT IDENTIFIER, hpnicfEponDeviceRMadlRemoteAddress MacAddress, hpnicfEponDeviceRMadlType INTEGER, hpnicfEponDeviceRMadlAction INTEGER, hpnicfEponDeviceRMadlEntryStatus RowStatus } hpnicfEponDeviceRemoteMACAddressLLIDName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "A locally-unique, administratively assigned name for a group of entries." ::= { hpnicfEponDeviceRemoteMACAddressLLIDEntry 1 } hpnicfEponDeviceRMadlLLID OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "An arbitrary integer for the purpose of identifying the LLID. Writing can be done all the time." DEFVAL { 1 } ::= { hpnicfEponDeviceRemoteMACAddressLLIDEntry 2 } hpnicfEponDeviceRMadlLogID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object identifier of a MIB module object to add to an entry, indicating the entry ID in the table. Writing can be done all the time." DEFVAL { zeroDotZero } ::= { hpnicfEponDeviceRemoteMACAddressLLIDEntry 3 } hpnicfEponDeviceRMadlRemoteAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The remote MAC address of the LLID. Writing can be done all the time." ::= { hpnicfEponDeviceRemoteMACAddressLLIDEntry 4 } hpnicfEponDeviceRMadlType OBJECT-TYPE SYNTAX INTEGER { notRegister (1), registered (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "A list of types for entries - LLIDs. Indicates and defines the state of registration. notRegister(1) marks a non registered LID, registered(2) marks a registered LLID. Writing can be done all the time." DEFVAL { 1 } ::= { hpnicfEponDeviceRemoteMACAddressLLIDEntry 5 } hpnicfEponDeviceRMadlAction OBJECT-TYPE SYNTAX INTEGER { none (1), register (2), deregister (3), reregister (4) } MAX-ACCESS read-create STATUS current DESCRIPTION "A list of actions for an entry - LLID. Indicates and defines the state of registration for the remote device. none(1) marks no action, register(2) marks to register an LLID, deregister(3) marks to deregister an LLID, reregister(4) marks reregistered LLID. Writing can be done all the time." DEFVAL { 1 } ::= { hpnicfEponDeviceRemoteMACAddressLLIDEntry 6 } hpnicfEponDeviceRMadlEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it." ::= { hpnicfEponDeviceRemoteMACAddressLLIDEntry 7 } --Statistics tables hpnicfEponDeviceStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfEponDeviceStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the list of statistics counters of EPON devices. The attributes are relevant for an OLT and an ONU." ::= { hpnicfEponDeviceStatObjects 1 } hpnicfEponDeviceStatEntry OBJECT-TYPE SYNTAX HpnicfEponDeviceStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for Table of statistics counters of EPON devices." INDEX { ifIndex } ::= { hpnicfEponDeviceStatTable 1 } HpnicfEponDeviceStatEntry ::= SEQUENCE { hpnicfEponDeviceStatTxFramesQueue0 Counter32, hpnicfEponDeviceStatTxFramesQueue1 Counter32, hpnicfEponDeviceStatTxFramesQueue2 Counter32, hpnicfEponDeviceStatTxFramesQueue3 Counter32, hpnicfEponDeviceStatTxFramesQueue4 Counter32, hpnicfEponDeviceStatTxFramesQueue5 Counter32, hpnicfEponDeviceStatTxFramesQueue6 Counter32, hpnicfEponDeviceStatTxFramesQueue7 Counter32, hpnicfEponDeviceStatRxFramesQueue0 Counter32, hpnicfEponDeviceStatRxFramesQueue1 Counter32, hpnicfEponDeviceStatRxFramesQueue2 Counter32, hpnicfEponDeviceStatRxFramesQueue3 Counter32, hpnicfEponDeviceStatRxFramesQueue4 Counter32, hpnicfEponDeviceStatRxFramesQueue5 Counter32, hpnicfEponDeviceStatRxFramesQueue6 Counter32, hpnicfEponDeviceStatRxFramesQueue7 Counter32, hpnicfEponDeviceStatDroppedFramesQueue0 Counter32, hpnicfEponDeviceStatDroppedFramesQueue1 Counter32, hpnicfEponDeviceStatDroppedFramesQueue2 Counter32, hpnicfEponDeviceStatDroppedFramesQueue3 Counter32, hpnicfEponDeviceStatDroppedFramesQueue4 Counter32, hpnicfEponDeviceStatDroppedFramesQueue5 Counter32, hpnicfEponDeviceStatDroppedFramesQueue6 Counter32, hpnicfEponDeviceStatDroppedFramesQueue7 Counter32 } hpnicfEponDeviceStatTxFramesQueue0 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-0- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 1 } hpnicfEponDeviceStatTxFramesQueue1 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-1- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 2 } hpnicfEponDeviceStatTxFramesQueue2 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-2- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 3 } hpnicfEponDeviceStatTxFramesQueue3 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-3- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 4 } hpnicfEponDeviceStatTxFramesQueue4 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-4- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 5 } hpnicfEponDeviceStatTxFramesQueue5 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-5- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 6 } hpnicfEponDeviceStatTxFramesQueue6 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-6- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 7 } hpnicfEponDeviceStatTxFramesQueue7 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-7- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 8 } hpnicfEponDeviceStatRxFramesQueue0 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-0- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 9 } hpnicfEponDeviceStatRxFramesQueue1 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-1- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 10 } hpnicfEponDeviceStatRxFramesQueue2 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-2- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 11 } hpnicfEponDeviceStatRxFramesQueue3 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-3- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 12 } hpnicfEponDeviceStatRxFramesQueue4 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-4- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 13 } hpnicfEponDeviceStatRxFramesQueue5 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-5- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 14 } hpnicfEponDeviceStatRxFramesQueue6 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-6- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 15 } hpnicfEponDeviceStatRxFramesQueue7 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-7- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { hpnicfEponDeviceStatEntry 16 } hpnicfEponDeviceStatDroppedFramesQueue0 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-0- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 17 } hpnicfEponDeviceStatDroppedFramesQueue1 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-1- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 18 } hpnicfEponDeviceStatDroppedFramesQueue2 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-2- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 19 } hpnicfEponDeviceStatDroppedFramesQueue3 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-3- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 20} hpnicfEponDeviceStatDroppedFramesQueue4 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-4- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 21 } hpnicfEponDeviceStatDroppedFramesQueue5 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-5- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 22 } hpnicfEponDeviceStatDroppedFramesQueue6 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-6- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 23 } hpnicfEponDeviceStatDroppedFramesQueue7 OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a -Queue-7- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { hpnicfEponDeviceStatEntry 24 } --Editor's Note use reference to event MIB modules [RFC2981] and --docsis MIB modules [RFC2669] hpnicfEponDeviceEventObjectTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfEponDeviceEventObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the Event Objects for EPON devices. The attributes are relevant for an OLT and an ONU." ::= { hpnicfEponDeviceEventObjects 1 } hpnicfEponDeviceEventObjectEntry OBJECT-TYPE SYNTAX HpnicfEponDeviceEventObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for Table of Event objects for EPON devices." INDEX { ifIndex } ::= { hpnicfEponDeviceEventObjectTable 1 } HpnicfEponDeviceEventObjectEntry ::= SEQUENCE { hpnicfEponDeviceSampleMinimum Integer32, hpnicfEponDeviceDyingGaspAlarmState TruthValue, hpnicfEponDeviceDyingGaspAlarmEnabled TruthValue, hpnicfEponDeviceCriticalEventState TruthValue, hpnicfEponDeviceCriticalEventEnabled TruthValue, hpnicfEponDeviceLocalLinkFaultAlarmState TruthValue, hpnicfEponDeviceLocalLinkFaultAlarmEnabled TruthValue, hpnicfEponDeviceTemperatureEventIndicationState TruthValue, hpnicfEponDeviceTemperatureEventIndicationEnabled TruthValue, hpnicfEponDevicePowerVoltageEventIndicationState TruthValue, hpnicfEponDevicePowerVoltageEventIndicationEnabled TruthValue, hpnicfEponDeviceGlobalEventState TruthValue, hpnicfEponDeviceGlobalEventEnabled TruthValue, hpnicfEponDeviceErroredSymbolPeriodEventState TruthValue, hpnicfEponDeviceErroredSymbolPeriodEventEnabled TruthValue, hpnicfEponDeviceErroredFrameEventState TruthValue, hpnicfEponDeviceErroredFrameEventEnabled TruthValue, hpnicfEponDeviceErroredFramePeriodEventState TruthValue, hpnicfEponDeviceErroredFramePeriodEventEnabled TruthValue, hpnicfEponDeviceErroredFrameSecondsSummaryEventState TruthValue, hpnicfEponDeviceErroredFrameSecondsSummaryEventEnabled TruthValue, hpnicfEponDeviceOrganizationSpecificEventState TruthValue, hpnicfEponDeviceOrganizationSpecificEventEnabled TruthValue, hpnicfEponDeviceEventControl INTEGER } hpnicfEponDeviceSampleMinimum OBJECT-TYPE SYNTAX Integer32 (1..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum Frequency of events this system will accept. A system may use the larger values of this minimum to lessen the impact of constant sampling. For larger sampling intervals the system samples less often and suffers less overhead. Unless explicitly resource limited, a system's value for this object SHOULD be 1, allowing as small as a 1 second interval for ongoing trigger sampling. Writing of the value can be done all the time." DEFVAL { 1 } ::= { hpnicfEponDeviceEventObjectEntry 1 } hpnicfEponDeviceDyingGaspAlarmState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Dying Gasp indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a dying gasp alarm asserted. When false the dying gasp alarm is reset " ::= { hpnicfEponDeviceEventObjectEntry 2 } hpnicfEponDeviceDyingGaspAlarmEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow DyingGaspAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 3 } hpnicfEponDeviceCriticalEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Critical Event indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Critical Event asserted. When false the Critical Event is reset." ::= { hpnicfEponDeviceEventObjectEntry 4 } hpnicfEponDeviceCriticalEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow CriticalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 5 } hpnicfEponDeviceLocalLinkFaultAlarmState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Local Link Fault indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Local Link Fault alarm asserted. When false the Local Link Fault alarm is reset." ::= { hpnicfEponDeviceEventObjectEntry 6 } hpnicfEponDeviceLocalLinkFaultAlarmEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow LocalLinkFaultAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 7 } hpnicfEponDeviceTemperatureEventIndicationState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Temperature Event indication of an EPON device. When condition of box temperature is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Temperature Event Indication asserted. When false the Temperature Event Indication is reset." ::= { hpnicfEponDeviceEventObjectEntry 8 } hpnicfEponDeviceTemperatureEventIndicationEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow TemperatureEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 9 } hpnicfEponDevicePowerVoltageEventIndicationState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Power/Voltage Event Indication of an EPON device. When condition of box Power/voltage is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Power/Voltage Event Indication asserted. When false the Power/Voltage Event Indication is reset. " ::= { hpnicfEponDeviceEventObjectEntry 10 } hpnicfEponDevicePowerVoltageEventIndicationEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow PowerVoltageEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 11 } hpnicfEponDeviceGlobalEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Global Event indication of an EPON device. When the indication of the event input occurs the event is asserted. When the input is removed that event is de-asserted. When true the device has a Global Event asserted. When false the Global Event Indication is reset." ::= { hpnicfEponDeviceEventObjectEntry 12 } hpnicfEponDeviceGlobalEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow GlobalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 13 } hpnicfEponDeviceErroredSymbolPeriodEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Symbol Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Symbol Period Event asserted. When false the Errored Symbol Period Event is reset." ::= { hpnicfEponDeviceEventObjectEntry 14 } hpnicfEponDeviceErroredSymbolPeriodEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredSymbolPeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 15 } hpnicfEponDeviceErroredFrameEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Frame Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Event asserted. When false the Errored Frame Event is reset." ::= { hpnicfEponDeviceEventObjectEntry 16 } hpnicfEponDeviceErroredFrameEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredFrameEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 17 } hpnicfEponDeviceErroredFramePeriodEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Frame Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Period Event asserted. When false the Errored Frame Period Event is reset." ::= { hpnicfEponDeviceEventObjectEntry 18 } hpnicfEponDeviceErroredFramePeriodEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredFramePeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 19 } hpnicfEponDeviceErroredFrameSecondsSummaryEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Frame Seconds Summary Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Seconds Summary Event asserted. When false the Errored Frame Seconds Summary Event is reset." ::= { hpnicfEponDeviceEventObjectEntry 20 } hpnicfEponDeviceErroredFrameSecondsSummaryEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredFrameSecondsSummaryEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 21 } hpnicfEponDeviceOrganizationSpecificEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Organization Specific Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Organization Specific Event asserted. When false the Organization Specific Event is reset." ::= { hpnicfEponDeviceEventObjectEntry 22 } hpnicfEponDeviceOrganizationSpecificEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow OrganizationSpecificEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time." DEFVAL { false } ::= { hpnicfEponDeviceEventObjectEntry 23 } hpnicfEponDeviceEventControl OBJECT-TYPE SYNTAX INTEGER { none(1), resetLog(2), useDefaultReporting(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates and controls the resetting of the Event log. Setting this object to none(1) has no action resetLog(2) empties the event log. All data is deleted. Setting it to useDefaultReporting(3) returns all event priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3)." DEFVAL { 3 } ::= { hpnicfEponDeviceEventObjectEntry 24 } -- Events Log Table hpnicfEponDeviceEventsLogTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfEponDeviceEventsLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects provides a log of notification based on the event as pointed to by entries in those tables. The intent is a MAC level event log (set of events to when they happened). This attribute is relevant for an OLT and an ONU." ::= { hpnicfEponDeviceEventObjects 2 } hpnicfEponDeviceEventsLogEntry OBJECT-TYPE SYNTAX HpnicfEponDeviceEventsLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A group of Events. Applications create and delete entries using hpnicfEponDeviceEventsEntryStatus. When adding objects to a notification they are added in the lexical order of their index in this table." INDEX { hpnicfEponDeviceEventsLogName, hpnicfEponDeviceEventsLogIndex } ::= { hpnicfEponDeviceEventsLogTable 1 } HpnicfEponDeviceEventsLogEntry ::= SEQUENCE { hpnicfEponDeviceEventsLogName SnmpAdminString, hpnicfEponDeviceEventsLogIndex Unsigned32, hpnicfEponDeviceEventsLogID OBJECT IDENTIFIER, hpnicfEponDeviceEventsLogFirstTime DateAndTime, hpnicfEponDeviceEventsLogLastTime DateAndTime, hpnicfEponDeviceEventsLogCounts Counter32, hpnicfEponDeviceEventsLogType INTEGER, hpnicfEponDeviceEventsLogEntryStatus RowStatus } hpnicfEponDeviceEventsLogName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A locally-unique, administratively assigned name for a group of Events." ::= { hpnicfEponDeviceEventsLogEntry 1 } hpnicfEponDeviceEventsLogIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer for the purpose of identifying individual Events within a hpnicfEponDeviceEventsLogName group. Events within a group are placed in the notification in the numerical order of this index." ::= { hpnicfEponDeviceEventsLogEntry 2 } hpnicfEponDeviceEventsLogID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object identifier of a MIB module object to add to a Notification that results from the event. Writing can be done all the time." DEFVAL { zeroDotZero } ::= { hpnicfEponDeviceEventsLogEntry 3 } hpnicfEponDeviceEventsLogFirstTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time that an entry was created." ::= { hpnicfEponDeviceEventsLogEntry 4 } hpnicfEponDeviceEventsLogLastTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "If multiple events are reported via the same entry, the time that the last event for this entry occurred, otherwise this should have the same value as hpnicfEponDeviceEventsLogFirstTime." ::= { hpnicfEponDeviceEventsLogEntry 5 } hpnicfEponDeviceEventsLogCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of consecutive event instances reported by this entry. This starts at 1 with the creation of this row and increments by 1 for each subsequent duplicate event." ::= { hpnicfEponDeviceEventsLogEntry 6 } hpnicfEponDeviceEventsLogType OBJECT-TYPE SYNTAX INTEGER { hpnicfEponDeviceDyingGaspAlarmState (1), hpnicfEponDeviceCriticalEventState (2), hpnicfEponDeviceLocalLinkFaultAlarmState (3), hpnicfEponDeviceTemperatureEventIndicationState (4), hpnicfEponDevicePowerVoltageEventIndicationState (5), hpnicfEponDeviceGlobalEventState (6), hpnicfEponDeviceErroredSymbolPeriodEventState (7), hpnicfEponDeviceErroredFrameEventState (8), hpnicfEponDeviceErroredFramePeriodEventState (9), hpnicfEponDeviceErroredFrameSecondsSummaryEventState (10), hpnicfEponDeviceOrganizationSpecificEventState (11) } MAX-ACCESS read-only STATUS current DESCRIPTION "A list of types for Events. Events are ordered according to their significance where 1 is the highest severity. hpnicfEponDeviceDyingGaspAlarmState(1) indicates a Dying Gasp Alarm State, hpnicfEponDeviceCriticalEventState(2) indicates a Critical Event State, hpnicfEponDeviceLocalLinkFaultAlarmState(3) indicates a Local Link Fault Alarm State, hpnicfEponDeviceTemperatureEventIndicationState(4) indicates a Temperature Event Indication State, hpnicfEponDevicePowerVoltageEventIndicationState(5) indicates a Power Voltage Event Indication State, hpnicfEponDeviceGlobalEventState(6) indicates a Global Event State, hpnicfEponDeviceErroredSymbolPeriodEventState(7) indicates an Errored Symbol Period Event State, hpnicfEponDeviceErroredFrameEventState(8) indicates an Errored Frame Event State, hpnicfEponDeviceErroredFramePeriodEventState(9) indicates an Errored Frame Period Event State, hpnicfEponDeviceErroredFrameSecondsSummaryEventState(10) indicates an Errored Frame Seconds Summary Event State, hpnicfEponDeviceOrganizationSpecificEventState(11) indicates an Organization Specific Event State. " ::= { hpnicfEponDeviceEventsLogEntry 7 } hpnicfEponDeviceEventsLogEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it." ::= { hpnicfEponDeviceEventsLogEntry 8 } -- Conformance Statements -- Conformance Groups hpnicfEponDeviceGroups OBJECT IDENTIFIER ::= { hpnicfEponDeviceConformance 1 } hpnicfEponDeviceGroupControl OBJECT-GROUP OBJECTS { hpnicfEponDeviceObjectReset, hpnicfEponDeviceObjectModes, hpnicfEponDeviceObjectFecEnabled, hpnicfEponDeviceObjectOamMode, hpnicfEponDeviceObjectDeviceReadyMode, hpnicfEponDeviceObjectPowerDown, hpnicfEponDeviceObjectNumberOfLLIDs, hpnicfEponDeviceObjectReportThreshold, hpnicfEponDeviceRemoteMACAddressLLIDControl } STATUS current DESCRIPTION "A collection of objects of hpnicfEponDevice control definition." ::= { hpnicfEponDeviceGroups 1 } hpnicfEponDeviceGroupRMadLTable OBJECT-GROUP OBJECTS { hpnicfEponDeviceRMadlLLID, hpnicfEponDeviceRMadlLogID, hpnicfEponDeviceRMadlRemoteAddress, hpnicfEponDeviceRMadlType, hpnicfEponDeviceRMadlAction, hpnicfEponDeviceRMadlEntryStatus } STATUS current DESCRIPTION "A collection of objects of hpnicfEponDevice remote Mac address to LLID table." ::= { hpnicfEponDeviceGroups 2 } hpnicfEponDeviceGroupStat OBJECT-GROUP OBJECTS { hpnicfEponDeviceStatTxFramesQueue0, hpnicfEponDeviceStatTxFramesQueue1, hpnicfEponDeviceStatTxFramesQueue2, hpnicfEponDeviceStatTxFramesQueue3, hpnicfEponDeviceStatTxFramesQueue4, hpnicfEponDeviceStatTxFramesQueue5, hpnicfEponDeviceStatTxFramesQueue6, hpnicfEponDeviceStatTxFramesQueue7, hpnicfEponDeviceStatRxFramesQueue0, hpnicfEponDeviceStatRxFramesQueue1, hpnicfEponDeviceStatRxFramesQueue2, hpnicfEponDeviceStatRxFramesQueue3, hpnicfEponDeviceStatRxFramesQueue4, hpnicfEponDeviceStatRxFramesQueue5, hpnicfEponDeviceStatRxFramesQueue6, hpnicfEponDeviceStatRxFramesQueue7, hpnicfEponDeviceStatDroppedFramesQueue0, hpnicfEponDeviceStatDroppedFramesQueue1, hpnicfEponDeviceStatDroppedFramesQueue2, hpnicfEponDeviceStatDroppedFramesQueue3, hpnicfEponDeviceStatDroppedFramesQueue4, hpnicfEponDeviceStatDroppedFramesQueue5, hpnicfEponDeviceStatDroppedFramesQueue6, hpnicfEponDeviceStatDroppedFramesQueue7 } STATUS current DESCRIPTION "A collection of objects of EPON device Statistics" ::= { hpnicfEponDeviceGroups 3 } hpnicfEponDeviceGroupEvent OBJECT-GROUP OBJECTS { hpnicfEponDeviceSampleMinimum, hpnicfEponDeviceDyingGaspAlarmState, hpnicfEponDeviceDyingGaspAlarmEnabled, hpnicfEponDeviceCriticalEventState, hpnicfEponDeviceCriticalEventEnabled, hpnicfEponDeviceLocalLinkFaultAlarmState, hpnicfEponDeviceLocalLinkFaultAlarmEnabled, hpnicfEponDeviceTemperatureEventIndicationState, hpnicfEponDeviceTemperatureEventIndicationEnabled, hpnicfEponDevicePowerVoltageEventIndicationState, hpnicfEponDevicePowerVoltageEventIndicationEnabled, hpnicfEponDeviceGlobalEventState, hpnicfEponDeviceGlobalEventEnabled, hpnicfEponDeviceErroredSymbolPeriodEventState, hpnicfEponDeviceErroredSymbolPeriodEventEnabled, hpnicfEponDeviceErroredFrameEventState, hpnicfEponDeviceErroredFrameEventEnabled, hpnicfEponDeviceErroredFramePeriodEventState , hpnicfEponDeviceErroredFramePeriodEventEnabled , hpnicfEponDeviceErroredFrameSecondsSummaryEventState , hpnicfEponDeviceErroredFrameSecondsSummaryEventEnabled, hpnicfEponDeviceOrganizationSpecificEventState , hpnicfEponDeviceOrganizationSpecificEventEnabled, hpnicfEponDeviceEventControl } STATUS current DESCRIPTION "A collection of objects for EPON device Events" ::= { hpnicfEponDeviceGroups 4 } hpnicfEponDeviceGroupEventLog OBJECT-GROUP OBJECTS { hpnicfEponDeviceEventsLogID, hpnicfEponDeviceEventsLogFirstTime, hpnicfEponDeviceEventsLogLastTime, hpnicfEponDeviceEventsLogCounts, hpnicfEponDeviceEventsLogType, hpnicfEponDeviceEventsLogEntryStatus } STATUS current DESCRIPTION "A collection of objects for EPON device Events log" ::= { hpnicfEponDeviceGroups 5 } -- Compliance hpnicfEponDeviceCompliances OBJECT IDENTIFIER ::= { hpnicfEponDeviceConformance 2 } hpnicfEponDeviceCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for EPON Devices." MODULE -- this module MANDATORY-GROUPS { hpnicfEponDeviceGroupControl } GROUP hpnicfEponDeviceGroupRMadLTable DESCRIPTION " This group is mandatory for all OLT EPON devices supporting LLID-MAC address table." GROUP hpnicfEponDeviceGroupStat DESCRIPTION "This group is mandatory for all EPON devices supporting interfaces for Statistics collection." GROUP hpnicfEponDeviceGroupEvent DESCRIPTION "This group is mandatory for all EPON devices supporting interfaces for event collection." GROUP hpnicfEponDeviceGroupEventLog DESCRIPTION "This group is mandatory for all EPON devices supporting interfaces for event log collection." ::= { hpnicfEponDeviceCompliances 1 } END