LUM-MPLS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32, Counter64 FROM SNMPv2-SMI OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF TEXTUAL-CONVENTION, DisplayString, DateAndTime, MacAddress, RowStatus FROM SNMPv2-TC lumModules, lumMplsMIB FROM LUM-REG MplsLabel, PortNumber FROM LUM-TC MgmtNameString, CommandString FROM LUM-TC; lumMplsMIBModule MODULE-IDENTITY LAST-UPDATED "201706150000Z" -- June 15th 2017 ORGANIZATION "Infinera Corporation" CONTACT-INFO "techsupport@infinera.com" DESCRIPTION "The MIB module for management of MPLS. The tables contained in this MIB are: (1) The General group contains some general attributes as time stamps and tables sizes. (2) The IF (interface) table contains information and configuration for all interfaces available for MPLS. (3) The XC table is used to associate in and out segments together, in order to form a cross-connect. (4) The Node table contains general information and configuration for each individual MPLS node. Every board in the physical node that supports MPLS is considered an individual MPLS node. (4) The tunnel table contains information and configuration for MPLS tunnel, which is a connection between two Label Switch Router, LSRs. (5) The LSP table contains information and configuration for each individual bidirectional Label Switched Path, LSP. (6) The tunnel-lsp table contains information about cross reference of tunnel and LSP. " REVISION "201706150000Z" -- June 15th 2017 DESCRIPTION "Changes made for release r29.0: - Changed ORGANIZATION and CONTACT-INFO" REVISION "201611300000Z" -- November 30th 2016 DESCRIPTION "Changes made for release r28.0: - Added mplsIfIfNo" REVISION "201501230000Z" -- January 23rd 2015 DESCRIPTION "Changes made for release r24.0: - Added description fields for MPLS Tunnel and MPLS LSP; mplsTunnelDescr, mplsLspDescr" REVISION "201310110000Z" -- October 11th 2013 DESCRIPTION "Updated for software release R22.0" REVISION "201304010000Z" -- April 1st 2013 DESCRIPTION "Updated for software release R21.0" REVISION "201212200000Z" -- December 20th 2012 DESCRIPTION "Update for software release R20.0: - Removed traffic class from LSP to pseudowires. - Updated mplsTunnelBookedBW to 64bit counter to avoid wrap. - Corrected ranges for MplsIdentifier, tunnelId and lspId. - Added range for mplsLspPriority." REVISION "201203010000Z" -- March 1st 2012 DESCRIPTION "Update for software release R19.0: - Added global ID and changed ITU ICC global ID to hidden. - Changed read/write properties of MEP IDs - Corrected maximum value of MEP IDs. - Changed support info. - Added support for BFD. - Added support for MPLS linear protection. - Added traffic class for LSP. - Changed storage class to read-create for XC out and in IF names." REVISION "201112200000Z" -- December 20th 2011 DESCRIPTION "The initial revision of this module." ::= { lumModules 40 } -- ---------------------------------------------------- -- Conformance area, containing groups and compliance -- specifications. -- ---------------------------------------------------- lumMplsConfs OBJECT IDENTIFIER ::= { lumMplsMIB 1 } lumMplsGroups OBJECT IDENTIFIER ::= { lumMplsConfs 1 } lumMplsCompl OBJECT IDENTIFIER ::= { lumMplsConfs 2 } -- ---------------------------------------------------- -- Root for objects in the MPLS MIB -- ---------------------------------------------------- lumMplsMIBObjects OBJECT IDENTIFIER ::= { lumMplsMIB 2 } -- ---------------------------------------------------- -- This MIB contains the following groups: -- ---------------------------------------------------- mplsGeneral OBJECT IDENTIFIER ::= { lumMplsMIBObjects 1 } mplsIfList OBJECT IDENTIFIER ::= { lumMplsMIBObjects 2 } mplsXCList OBJECT IDENTIFIER ::= { lumMplsMIBObjects 3 } mplsTunnelList OBJECT IDENTIFIER ::= { lumMplsMIBObjects 4 } mplsNodeList OBJECT IDENTIFIER ::= { lumMplsMIBObjects 5 } mplsLspList OBJECT IDENTIFIER ::= { lumMplsMIBObjects 6 } mplsTnlXLspList OBJECT IDENTIFIER ::= { lumMplsMIBObjects 7 } -- ---------------------------------------------------- -- Textual Conventions -- ---------------------------------------------------- MplsIdentifier ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "MPLS identifier type, 16-bit integer." SYNTAX Unsigned32 (0..65535) -- ---------------------------------------------------- -- General group -- ---------------------------------------------------- mplsGeneralLastChangeTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the configuration of the MIB was last changed. " ::= { mplsGeneral 1 } mplsGeneralStateLastChangeTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the state of the MIB was last changed. " ::= { mplsGeneral 2 } mplsGeneralMplsIfTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Size of interface table " ::= { mplsGeneral 3 } mplsGeneralMplsXCTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Size of cross connect table " ::= { mplsGeneral 4 } mplsGeneralMplsTunnelTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Size of tunnel table " ::= { mplsGeneral 5 } mplsGeneralMplsNodeTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Size of node table " ::= { mplsGeneral 6 } mplsGeneralMplsLspTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Size of LSP table " ::= { mplsGeneral 7 } mplsGeneralMplsTnlXLspTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Size of Tunnel LSP cross reference table " ::= { mplsGeneral 8 } -- ---------------------------------------------------- -- Interface group -- ---------------------------------------------------- mplsIfTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS interface list." ::= { mplsIfList 1 } mplsIfEntry OBJECT-TYPE SYNTAX MplsIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the mpls interface list. " INDEX { mplsIfIndex } ::= { mplsIfTable 1 } MplsIfEntry ::= SEQUENCE { mplsIfIndex Unsigned32, mplsIfName MgmtNameString, mplsIfSubrack Unsigned32, mplsIfSlot Unsigned32, mplsIfTxPort PortNumber, mplsIfPortIndex Unsigned32, mplsIfPortName DisplayString, mplsIfInternalReference Unsigned32, mplsIfAdminStatus INTEGER, mplsIfIdentifier DisplayString, mplsIfNextHopMacAddress MacAddress, mplsIfInterfaceMacAddress MacAddress, mplsIfVlan Unsigned32, mplsIfRowStatus RowStatus, mplsIfIfNo PortNumber, mplsIfResourceType INTEGER, mplsIfLagId MgmtNameString } mplsIfIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary index assigned to each entry. " ::= { mplsIfEntry 1 } mplsIfName OBJECT-TYPE SYNTAX MgmtNameString MAX-ACCESS read-only STATUS current DESCRIPTION "The management name of the interface, for example 'if:1:2:myIdentifier', where the first number indicates subrack and the second slot number. " ::= { mplsIfEntry 2 } mplsIfSubrack OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The subrack of the physical port that this interface is bound to. " ::= { mplsIfEntry 3 } mplsIfSlot OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The slot of the physical port that this interface is bound to. " ::= { mplsIfEntry 4 } mplsIfTxPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The transmitting physical port that this interface is bound to. " DEFVAL { 0 } ::= { mplsIfEntry 5 } mplsIfPortIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the port or lag that this interface is bound to. " ::= { mplsIfEntry 6 } mplsIfPortName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the port or lag that this interface is bound to. " ::= { mplsIfEntry 7 } mplsIfInternalReference OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "For internal use only. " DEFVAL { 0 } ::= { mplsIfEntry 8 } mplsIfAdminStatus OBJECT-TYPE SYNTAX INTEGER { down (1), up (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative state of the MPLS interface. down - The interface is de-activated. up - The interface is activated. " DEFVAL { up } ::= { mplsIfEntry 9 } mplsIfIdentifier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "A unique identifier for the MPLS interface. " DEFVAL { "" } ::= { mplsIfEntry 10 } mplsIfNextHopMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The unicast or valid multicast (01:00:5E:90:00:00) MAC address used for sending MPLS packets on the interface. A configured next hop MAC Address on an interface will be used as the next hop MAC address for any cross-connect that the interface is part of. " ::= { mplsIfEntry 11 } mplsIfInterfaceMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The unicast MAC address used for receiving MPLS packets on the interface. If no interface MAC address is defined, the predefined MAC address for the physical port will be used. " ::= { mplsIfEntry 12 } mplsIfVlan OBJECT-TYPE SYNTAX Unsigned32(0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "The backbone VLAN id used when transmitting and receiving MPLS packets on the interface. " DEFVAL { 0 } ::= { mplsIfEntry 13 } mplsIfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Manages creation and deletion of conceptual rows. See also SNMPv2-TC. Note: The newly created object will not necessarily receive the same index as used in the create procedure. " ::= { mplsIfEntry 14 } mplsIfIfNo OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The physical interface number of the multi-connector port. " DEFVAL { 1 } ::= { mplsIfEntry 15 } mplsIfResourceType OBJECT-TYPE SYNTAX INTEGER { port (1), lag (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of resource the Mpls If is created on. " DEFVAL { port } ::= { mplsIfEntry 16 } mplsIfLagId OBJECT-TYPE SYNTAX MgmtNameString MAX-ACCESS read-create STATUS current DESCRIPTION "The identifier of the LAG for Mpls If. An empty string means no Mpls interface on LAG. " DEFVAL { "" } ::= { mplsIfEntry 17 } -- ---------------------------------------------------- -- XC table -- ---------------------------------------------------- mplsXCTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsXCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for associating in and out segments together in order to form a cross-connect." ::= { mplsXCList 1 } mplsXCEntry OBJECT-TYPE SYNTAX MplsXCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the MPLS cross-connect list. There are two special cases for LERs: 1. LSPs originated at this LSR: These are represented by using the value zero for inSegmentIfIndex. 2. LSPs terminating at this LSR: These are represented by using the value zero for outSegmentIfIndex. " INDEX { mplsXCIndex } ::= { mplsXCTable 1 } MplsXCEntry ::= SEQUENCE { mplsXCIndex Unsigned32, mplsXCName MgmtNameString, mplsXCInternalReference Unsigned32, mplsXCIdentifier DisplayString, mplsXCInSegmentIfIndex Unsigned32, mplsXCInSegmentIfName DisplayString, mplsXCInSegmentLabel MplsLabel, mplsXCOutSegmentIfIndex Unsigned32, mplsXCOutSegmentIfName DisplayString, mplsXCOutSegmentLabel MplsLabel, mplsXCRowStatus RowStatus } mplsXCIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary index assigned to each entry. " ::= { mplsXCEntry 1 } mplsXCName OBJECT-TYPE SYNTAX MgmtNameString MAX-ACCESS read-only STATUS current DESCRIPTION "The management name of the entry, for example 'xc:1:2:myIdentifier', where the first number indicates subrack, the second slot number. 'myIdentifier' is the unique identifier specified by mplsXCIdentifier. " ::= { mplsXCEntry 2 } mplsXCInternalReference OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "For internal use only. " DEFVAL { 0 } ::= { mplsXCEntry 3 } mplsXCIdentifier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "A unique identifier for the cross-connect object. " DEFVAL { "" } ::= { mplsXCEntry 4 } mplsXCInSegmentIfIndex OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Index of the incoming MPLS interface. The value zero indicates a special case (LER) outlined in the table description. " ::= { mplsXCEntry 5 } mplsXCInSegmentIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of the incoming segment. " ::= { mplsXCEntry 6 } mplsXCInSegmentLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-create STATUS current DESCRIPTION "The MPLS label for the incoming traffic. Actual label range is 16-1048575, 0-15 is reserved. " ::= { mplsXCEntry 7 } mplsXCOutSegmentIfIndex OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Index of the outgoing MPLS interface. The value zero indicates a special case (LER) outlined in the table description. " ::= { mplsXCEntry 8 } mplsXCOutSegmentIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of the outgoing segment. " ::= { mplsXCEntry 9 } mplsXCOutSegmentLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-create STATUS current DESCRIPTION "The MPLS label for the outgoing traffic. Actual label range is 16-1048575, 0-15 is reserved. " ::= { mplsXCEntry 10 } mplsXCRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Manages creation and deletion of conceptual rows. See also SNMPv2-TC. Note: The newly created object will not necessarily receive the same index as used in the create procedure. " ::= { mplsXCEntry 11 } -- ---------------------------------------------------- -- Tunnel table -- ---------------------------------------------------- mplsTunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS tunnel list." ::= { mplsTunnelList 1 } mplsTunnelEntry OBJECT-TYPE SYNTAX MplsTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the MPLS tunnel list. " INDEX { mplsTunnelIndex } ::= { mplsTunnelTable 1 } MplsTunnelEntry ::= SEQUENCE { mplsTunnelIndex Unsigned32, mplsTunnelInternalReference Unsigned32, mplsTunnelIdentifier DisplayString, mplsTunnelName MgmtNameString, mplsTunnelActiveLSP DisplayString, mplsTunnelActiveLspIndex Unsigned32, mplsTunnelState INTEGER, mplsTunnelSrcNodeId Unsigned32, mplsTunnelSrcTunnelId MplsIdentifier, mplsTunnelDestNodeId Unsigned32, mplsTunnelDestTunnelId MplsIdentifier, mplsTunnelExtId DisplayString, mplsTunnelAssociateLSP CommandString, mplsTunnelRowStatus RowStatus, mplsTunnelLinearProtection DisplayString, mplsTunnelProtectionState INTEGER, mplsTunnelAssociateLinearProt CommandString, mplsTunnelGlobalId Unsigned32, mplsTunnelDestGlobalId Unsigned32, mplsTunnelWorkingLSP DisplayString, mplsTunnelProtectionLSP DisplayString, mplsTunnelReservedBW Unsigned32, mplsTunnelBookedBW Counter64, mplsTunnelDescr DisplayString} mplsTunnelIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary index assigned to each entry. " ::= { mplsTunnelEntry 1 } mplsTunnelInternalReference OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "For internal use only. " DEFVAL { 0 } ::= { mplsTunnelEntry 2 } mplsTunnelIdentifier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Unique identifier used for referencing this object. " DEFVAL { "" } ::= { mplsTunnelEntry 3 } mplsTunnelName OBJECT-TYPE SYNTAX MgmtNameString MAX-ACCESS read-only STATUS current DESCRIPTION "The management name of the entry, for example 'tunnel:1:2:id', where the first number indicates subrack, the second slot number and the id is the unique tunnel identifier. " ::= { mplsTunnelEntry 4 } mplsTunnelActiveLSP OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "ID of the associated LSP that is active, if exists. " DEFVAL { "" } ::= { mplsTunnelEntry 5 } mplsTunnelActiveLspIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the associated LSP that is active, if exists. " ::= { mplsTunnelEntry 6 } mplsTunnelState OBJECT-TYPE SYNTAX INTEGER { down (1), up (2), unknown (3)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the state of the tunnel. down (1) -- The tunnel is de-actived or unavailable to carry any traffic. up (2) -- The tunnel is active and ready to carry traffic. unknown (3) -- The tunnel status can not be verified. " ::= { mplsTunnelEntry 7 } mplsTunnelSrcNodeId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of the source node, i.e. the node where this tunnel originates. Used for externally uniquely identifying the tunnel in the standardized format, '[Src Global ID]:[Src Node ID]:[Src Tunnel ID]- [Dest. Global ID]:[Dest. Node ID]:[Dest. Tunnel ID]'. A zero value indicates that the node ID is not set. This value can be set in the MPLS node settings. A change in the MPLS node attribute will change this value for the whole traffic unit. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsTunnelEntry 8 } mplsTunnelSrcTunnelId OBJECT-TYPE SYNTAX MplsIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The source node MPLS-TP tunnel ID of this tunnel. Used for externally uniquely identifying the tunnel in the standardized format, '[Src Global ID]:[Src Node ID]:[Src Tunnel ID]- [Dest. Global ID]:[Dest. Node ID]:[Dest. Tunnel ID]'. A zero value indicates that the tunnel ID is not set. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsTunnelEntry 9 } mplsTunnelDestNodeId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The ID of the destination node, i.e. the node where this tunnel terminates. Used for externally uniquely identifying the tunnel in the standardized format, '[Src Global ID]:[Src Node ID]:[Src Tunnel ID]- [Dest. Global ID]:[Dest. Node ID]:[Dest. Tunnel ID]'. A zero value indicates that the node ID is not set. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsTunnelEntry 10 } mplsTunnelDestTunnelId OBJECT-TYPE SYNTAX MplsIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The destination node MPLS-TP tunnel ID of the tunnel. Used for externally uniquely identifying the tunnel in the standardized format, '[Src global ID]:[Src node ID]:[Src tunnel ID]- [Dest. global ID]:[Dest. node ID]:[Dest. tunnel ID]'. A zero value indicates that the tunnel ID is not set. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsTunnelEntry 11 } mplsTunnelExtId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The global ID of the tunnel, used for externally uniquely identifying the tunnel in the standardized format, '[Src global ID]:[Src node ID]:[Src tunnel ID]- [Dest. global ID]:[Dest. node ID]:[Dest. tunnel ID]'. An empty string indicates that the external tunnel ID is not set. " REFERENCE "MPLS-TP Identifiers [TPIDS]" ::= { mplsTunnelEntry 12 } mplsTunnelAssociateLSP OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for mapping a new LSP to the tunnel. The first LSP associated to the tunnel will be the primary path and the additional LSPs will be the protection path. Identifier -- the tunnel which the LSP is associated to. LSP ID -- which LSP to associated with the tunnel. " ::= { mplsTunnelEntry 13 } mplsTunnelRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Manages creation and deletion of conceptual rows. See also SNMPv2-TC. Note: The newly created object will not necessarily receive the same index as used in the create procedure. " ::= { mplsTunnelEntry 14 } mplsTunnelLinearProtection OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The linear protection profile applied to the tunnel. Protection state coordination (PSC) protocol is used for linear protection. " DEFVAL { "none" } ::= { mplsTunnelEntry 15 } mplsTunnelProtectionState OBJECT-TYPE SYNTAX INTEGER { fullyworking (1), degraded (2), failed (3), unknown (4)} MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the linear protection that applied to the tunnel fullyworking (1) -- both protection and working path are fully active degraded (2) -- service degraded on the protection domain failed (3) -- failure condition reported on both protection and working path unknown (4) -- no board present " ::= { mplsTunnelEntry 16 } mplsTunnelAssociateLinearProt OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for create and associate a PSC (Protection State Coordination) protocol for linear protection of the tunnel. Only supported 1:1 protection architecture: a protection transport path is dedicated to the working transport path of a single service and the traffic is only transmitted either on the working or the protection path, by using a selector at the source of the protection domain. The active LSP associated with the tunnel will be the working path. Protection path -- the Identifier of the protection LSP path Mode -- revertive/non-revertive mode of the protection domain WTR timer -- wait-to-restore timer, used to delay reversion to normal state when recovering from a failure condition on the working path and the protection domain is configured for revertive behavior Continuous message interval -- interval of continuous control message Rapid message interval -- interval of three rapid control messages After associate the linear protection, the cross reference of the protection LSP and the tunnel will be displayed in mplsTnlXLspTable. " ::= { mplsTunnelEntry 17 } mplsTunnelGlobalId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object allows the administrator to assign a unique operator identifier also called MPLS-TP Global Identifier. The Global Identifier can contain the 2-octet or 4-octet value of the operators Autonomous System Number (ASN). The value zero indicates that the value is not initialized but will work inside a single carrier network. This value can be set in the MPLS node settings. A change in the MPLS node attribute will change this value for the whole traffic unit. " REFERENCE "MPLS-TP Identifiers" DEFVAL { 0 } ::= { mplsTunnelEntry 18 } mplsTunnelDestGlobalId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows the administrator to assign a unique operator identifier also called MPLS-TP Global Identifier. The Global Identifier can contain the 2-octet or 4-octet value of the operators Autonomous System Number (ASN). The value zero indicates that the value is not initialized but will work inside a single carrier network. " REFERENCE "MPLS-TP Identifiers" DEFVAL { 0 } ::= { mplsTunnelEntry 19 } mplsTunnelWorkingLSP OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Identifier of the working path of the linear protection. " ::= { mplsTunnelEntry 20 } mplsTunnelProtectionLSP OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Identifier of the protection path of the linear protection. " ::= { mplsTunnelEntry 21 } mplsTunnelReservedBW OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Bandwidth reserved by the tunnel. Default value is 0 and indicates that no bandwidth has been allocated by the tunnel. " DEFVAL { 0 } ::= { mplsTunnelEntry 22 } mplsTunnelBookedBW OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total amount of bandwidth booked by pseudowires in the tunnel. " ::= { mplsTunnelEntry 23 } mplsTunnelDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "User configurable label. " DEFVAL { "" } ::= { mplsTunnelEntry 24 } -- ---------------------------------------------------- -- Node table -- ---------------------------------------------------- mplsNodeTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsNodeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS node list. Each individual board that supports MPLS node is considered a MPLS node." ::= { mplsNodeList 1 } mplsNodeEntry OBJECT-TYPE SYNTAX MplsNodeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the MPLS node list. " INDEX { mplsNodeIndex } ::= { mplsNodeTable 1 } MplsNodeEntry ::= SEQUENCE { mplsNodeIndex Unsigned32, mplsNodeName MgmtNameString, mplsNodeSubrack Unsigned32, mplsNodeSlot Unsigned32, mplsNodeIccIdStr OCTET STRING, mplsNodeIdNum Unsigned32, mplsNodeCreateXC CommandString, mplsNodeCreateTunnel CommandString, mplsNodeCreateLsp CommandString, mplsNodeCreatePw CommandString, mplsNodeCreateIf CommandString, mplsNodeLinearProtMode INTEGER, mplsNodeLinearProtWtrTimer Unsigned32, mplsNodeLPContMsgInterval Unsigned32, mplsNodeLPRapidMsgInterval Unsigned32, mplsNodeGlobalId Unsigned32, mplsNodeCreateMsPw CommandString, mplsNodeCreateLsp2 CommandString, mplsNodeCreateTunnelAdvanced CommandString, mplsNodeCreateLspAdvanced CommandString, mplsNodeCreatePwGeneric CommandString, mplsNodeCreatePwMpls CommandString, mplsNodeCreatePwEnet CommandString, mplsNodeCreateBfdTemplate CommandString, mplsNodeCreateXCAdvanced CommandString } mplsNodeIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary index assigned to each entry. " ::= { mplsNodeEntry 1 } mplsNodeName OBJECT-TYPE SYNTAX MgmtNameString MAX-ACCESS read-only STATUS current DESCRIPTION "The management name of the interface, for example 'node:1:2', where the first number indicates subrack, the second slot number. " ::= { mplsNodeEntry 2 } mplsNodeSubrack OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The subrack that this MPLS node belongs to. " ::= { mplsNodeEntry 3 } mplsNodeSlot OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The slot that this MPLS node belongs to. " ::= { mplsNodeEntry 4 } mplsNodeIccIdStr OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..6)) MAX-ACCESS read-write STATUS current DESCRIPTION "Unique code assigned to the network operator or service provider maintained by ITU-T. The ITU carrier code used to form a globally unique node ID for non IP environments. " ::= { mplsNodeEntry 5 } mplsNodeIdNum OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Unique node ID / router ID assigned with in the scope of the network of the operator / service provider, defined by the ICC ID. This value is unique and only valid for this board. Accepted values are 0.0.0.0 - 255.255.255.255. If this value is changed all MPLS-TP MP IDs on this board will be updated. All BFD sessions on the board will need to be in administrative down. " ::= { mplsNodeEntry 6 } mplsNodeCreateXC OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a XC entry. In-segment name - Name of the incoming segment. In-segment label - The MPLS label for the incoming traffic. Out-segment name - Name of the outgoing segment. Out-segment label - The MPLS label for the outgoing traffic. By not selecting an out interface or an in interface a cross-connect for a LER, Label Edge Router, is created. " ::= { mplsNodeEntry 7 } mplsNodeCreateTunnel OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION " Identifier - Unique tunnel ID used when referencing the tunnel within the node. MPLS-TP ID - Set the standard MPLS-TP ID for the tunnel on the format: ':::: :: :: ::'. This is to simplify unique identification of the tunnel in the entire network. Local node and tunnel ID will be used as source IDs, while peer node and tunnel ID will be used as destination IDs. Associate LSP - Associate any existing LSP not already allocated to a tunnel. Create new LSP - Create a new LSP allocated with the tunnel. LSP identifier - Unique LSP ID used when referencing the LSP within the node. Interface - Id of the MPLS interface the LSP is bound to. Outgoing label - MPLS label appended to outgoing MPLS packets for this LSP. Incoming label - MPLS label used to identify incoming MPLS packets on the interface above as part of this LSP. " ::= { mplsNodeEntry 8 } mplsNodeCreateLsp OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. Role - Defines whether the LSP is terminated/initiated in the node (edge) or not (transit). Interface - ID of the MPLS interface the LSP is bound to. Outlabel - MPLS label appended to outgoing MPLS packets for this LSP. Inlabel - MPLS label used to identify incoming MPLS packets on the interface above as part of this LSP. Interface 2 - Id of the MPLS interface the LSP bound to in the reverse direction. Only valid for transit LSPs. Outlabel 2 - MPLS label appended to outgoing MPLS packets on Interface 2. Only valid for transit LSPs. Inlabel 2 - MPLS label used identify incoming MPLS packets on Interface 2 as part of this LSP. Only valid for transit LSPs. Tunnel - The internal ID of the tunnel an edge LSP shall be part of. Only valid for edge LSP objects. MPLS-TP ID - For transit LSPs, it is possible to set the standard MPLS-TP ID on the format: ':::::: :: :: ::::'. This is to simplify identification of the LSP on all nodes in the network. LSPs initiated/terminated on this node (edge) will inherit MPLS-TP ID data from its associated tunnel. " ::= { mplsNodeEntry 9 } mplsNodeCreatePw OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION " Pseudowire ID - Unique pseudowire ID used when referencing the pseudowire within the node. Pseudowire type - Edge pseudowire connects to a singel tunnel while a multi-segment pseudowire connects two tunnels. Outlabel - Pseudowire label appended to outgoing packets for this pseudowire. Inlabel - Pseudowire label used to identify incoming MPLS packets as part of this pseudowire. Traffic class - The traffic class of the pseudowire TTL - Time to live indicates the time that a packet still has before its life ends and is dropped. The packets TTL is decremented by 1 at each hop. If the TTL reaches 0, the packet is dropped. Tunnel - ID of the MPLS tunnel the pseudowire is bound to. Flow label - Flow label (acccording to RFC 6391). Set to enabled or disabled. port - Pseudowire classification on port means that all traffic on this port is mapped into the pseudowire. VLAN - All traffic on the selected port with the specified VLAN tag is mapped into the pseudowire Classification - All traffic identified by this policy classification is mapped into the pseudowire. PW operation mode - Service delimiting operations is performed on the packages in the pseudowire by selecting Raw or Tagged mode. " ::= { mplsNodeEntry 10 } mplsNodeCreateIf OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating an interface. Identifier - Unique MPLS interface ID used when referencing the interface within the node. Admin Status - Defines whether the interface shall be active or not. Port - Physical port that the interface is connected to. VLAN ID - VLAN ID prepended on all MPLS packets sent on this interface. Next hop MAC - Destination MAC address prepended to all MPLS packets sent on this interface. Interface - Source MAC address prepended to all MPLS packets sent on this interface. " ::= { mplsNodeEntry 11 } mplsNodeLinearProtMode OBJECT-TYPE SYNTAX INTEGER { nonRevertive (1), revertive (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "The mode of the protection domain, configured for all MPLS linear protection service on the board. nonRevertive (1) -- non-revertive mode revertive (2) -- revertive mode " DEFVAL { revertive } ::= { mplsNodeEntry 12 } mplsNodeLinearProtWtrTimer OBJECT-TYPE SYNTAX Unsigned32 (1..720) MAX-ACCESS read-write STATUS current DESCRIPTION "The wait-to-restore (WTR) timer configured for all MPLS linear protection service on the board. A WTR timer is used to delay reversion to Normal state when recovering from a failure condition on the working path and the protection domain is configured for revertive behavior. Unit: second. " DEFVAL { 300 } ::= { mplsNodeEntry 13 } mplsNodeLPContMsgInterval OBJECT-TYPE SYNTAX Unsigned32 (1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "In linear protection domain, the control message is transmitted over the protection path only. Subsequent messages are continuously transmitted to verify that the session is alive. If no valid control message is received, that last valid received message is applicable. The continuous message interval is configured for all linear protection service on the board. Unit: second. " DEFVAL { 5 } ::= { mplsNodeEntry 14 } mplsNodeLPRapidMsgInterval OBJECT-TYPE SYNTAX Unsigned32 (1..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "In linear protection domain, when the state of the protection domain is changed, three control messages shall be transmitted as quickly as possible to allow for rapid protection switching. After the transmission of the three rapid messages, the most recently transmitted control message will be retransmitted on the continual basis. The rapid message interval is configured for all linear protection service on the board. Unit: millisecond. " DEFVAL { 3 } ::= { mplsNodeEntry 15 } mplsNodeGlobalId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows the administrator to assign a unique operator identifier also called MPLS-TP Global Identifier. The Global Identifier can contain the 2-octet or 4-octet value of the operators Autonomous System Number (ASN). The value zero indicates that the value is not initialized but will work inside a single carrier network. When changing this value all global IDs on the board will be changed. Destination Global IDs will also be set unless already set to a value. " REFERENCE "MPLS-TP Identifiers" DEFVAL { 0 } ::= { mplsNodeEntry 16 } mplsNodeCreateMsPw OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a multi-segment pseudowire. Identifier - Unique pseudowire ID used when referencing the pseudowire within the node. East outlabel - Pseudowire label appended to outgoing packets for this pseudowire in east direction. East Inlabel - Pseudowire label used to identify incoming MPLS packets as part of this pseudowire in east direction. East Tunnel - ID of the MPLS tunnel the pseudowire is bound to in east direction. West outlabel - Pseudowire label appended to outgoing packets for this pseudowire in west direction. West Inlabel - Pseudowire label used to identify incoming MPLS packets as part of this pseudowire in west direction. West Tunnel - ID of the MPLS tunnel the pseudowire is bound to in west direction. " ::= { mplsNodeEntry 17 } mplsNodeCreateLsp2 OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. Role - Defines whether the LSP is terminated/initiated in the node (edge) or not (transit). Interface - ID of the MPLS interface the LSP is bound to. Outlabel - MPLS label appended to outgoing MPLS packets for this LSP. Inlabel - MPLS label used to identify incoming MPLS packets on the interface above as part of this LSP. Interface 2 - Id of the MPLS interface the LSP bound to in the reverse direction. Only valid for transit LSPs. Outlabel 2 - MPLS label appended to outgoing MPLS packets on Interface 2. Only valid for transit LSPs. Inlabel 2 - MPLS label used identify incoming MPLS packets on Interface 2 as part of this LSP. Only valid for transit LSPs. Tunnel - The internal ID of the tunnel an edge LSP shall be part of. Only valid for edge LSP objects. MPLS-TP ID - For transit LSPs, it is possible to set the standard MPLS-TP ID on the format: ':::::: :: :: ::::'. This is to simplify identification of the LSP on all nodes in the network. LSPs initiated/terminated on this node (edge) will inherit MPLS-TP ID data from its associated tunnel. " ::= { mplsNodeEntry 18 } mplsNodeCreateTunnelAdvanced OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION " Identifier - Unique tunnel ID used when referencing the tunnel within the node. MPLS-TP ID - Set the standard MPLS-TP ID for the tunnel on the format: ':::: :: :: ::'. This is to simplify unique identification of the tunnel in the entire network. Local node and tunnel ID will be used as source IDs, while peer node and tunnel ID will be used as destination IDs. Associate LSP - Associate any existing LSP not already allocated to a tunnel. Create new LSP - Create a new LSP allocated with the tunnel. LSP identifier - Unique LSP ID used when referencing the LSP within the node. Interface - Id of the MPLS interface the LSP is bound to. Outgoing label - MPLS label appended to outgoing MPLS packets for this LSP. Incoming label - MPLS label used to identify incoming MPLS packets on the interface above as part of this LSP. " ::= { mplsNodeEntry 19 } mplsNodeCreateLspAdvanced OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. Role - Defines whether the LSP is terminated/initiated in the node (edge) or not (transit). Interface - ID of the MPLS interface the LSP is bound to. Outlabel - MPLS label appended to outgoing MPLS packets for this LSP. Inlabel - MPLS label used to identify incoming MPLS packets on the interface above as part of this LSP. Interface 2 - Id of the MPLS interface the LSP bound to in the reverse direction. Only valid for transit LSPs. Outlabel 2 - MPLS label appended to outgoing MPLS packets on Interface 2. Only valid for transit LSPs. Inlabel 2 - MPLS label used identify incoming MPLS packets on Interface 2 as part of this LSP. Only valid for transit LSPs. Tunnel - The internal ID of the tunnel an edge LSP shall be part of. Only valid for edge LSP objects. MPLS-TP ID - For transit LSPs, it is possible to set the standard MPLS-TP ID on the format: ':::::: :: :: ::::'. This is to simplify identification of the LSP on all nodes in the network. LSPs initiated/terminated on this node (edge) will inherit MPLS-TP ID data from its associated tunnel. " ::= { mplsNodeEntry 20 } mplsNodeCreatePwGeneric OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. " ::= { mplsNodeEntry 21 } mplsNodeCreatePwMpls OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. " ::= { mplsNodeEntry 22 } mplsNodeCreatePwEnet OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. " ::= { mplsNodeEntry 23 } mplsNodeCreateBfdTemplate OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a new BFD template. Identifier - The unique identifier for the template. Tx Interval - Minimum interval for sending BFD control packets. Configurable in intervals of 100 ms. Rx Interval - Minimum interval for receiving BFD control packets. Configurable in intervals of 100 ms. " ::= { mplsNodeEntry 24 } mplsNodeCreateXCAdvanced OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command for creating a XC entry. In-segment name - Name of the incoming segment. In-segment label - The MPLS label for the incoming traffic. Out-segment name - Name of the outgoing segment. Out-segment label - The MPLS label for the outgoing traffic. By not selecting an out interface or an in interface a cross-connect for a LER, Label Edge Router, is created. " ::= { mplsNodeEntry 25 } -- ---------------------------------------------------- -- The MPLS tunnel LSP cross connect table -- ---------------------------------------------------- mplsTnlXLspTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTnlXLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS tunnel to LSP cross reference group list." ::= { mplsTnlXLspList 1 } mplsTnlXLspEntry OBJECT-TYPE SYNTAX MplsTnlXLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the MPLS tunnel LSP cross reference list. " INDEX { mplsTnlXLspIndex } ::= { mplsTnlXLspTable 1 } MplsTnlXLspEntry ::= SEQUENCE { mplsTnlXLspIndex Unsigned32, mplsTnlXLspName MgmtNameString, mplsTnlXLspInternalReference Unsigned32, mplsTnlXLspTunnelId DisplayString, mplsTnlXLspLspId DisplayString, mplsTnlXLspRowStatus RowStatus} mplsTnlXLspIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary index assigned to each entry. " ::= { mplsTnlXLspEntry 1 } mplsTnlXLspName OBJECT-TYPE SYNTAX MgmtNameString MAX-ACCESS read-only STATUS current DESCRIPTION "The management name of the interface, for example 'tnlXLsp:1:2', where the first number indicates subrack, the second slot number. " ::= { mplsTnlXLspEntry 2 } mplsTnlXLspInternalReference OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "For internal use only. " DEFVAL { 0 } ::= { mplsTnlXLspEntry 3 } mplsTnlXLspTunnelId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Tunnel ID of this cross reference entry. " DEFVAL { "" } ::= { mplsTnlXLspEntry 4 } mplsTnlXLspLspId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "LSP ID of this cross reference entry. " DEFVAL { "" } ::= { mplsTnlXLspEntry 5 } mplsTnlXLspRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Manages creation and deletion of conceptual rows. See also SNMPv2-TC. Note: The newly created object will not necessarily receive the same index as used in the create procedure. " ::= { mplsTnlXLspEntry 6 } -- ---------------------------------------------------- -- Lsp table -- ---------------------------------------------------- mplsLspTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS Label Switched Path group list. Each entry in the table represent a bidirectional LSP." ::= { mplsLspList 1 } mplsLspEntry OBJECT-TYPE SYNTAX MplsLspEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the MPLS LSP list. " INDEX { mplsLspIndex } ::= { mplsLspTable 1 } MplsLspEntry ::= SEQUENCE { mplsLspIndex Unsigned32, mplsLspName MgmtNameString, mplsLspInternalReference Unsigned32, mplsLspIdentifier DisplayString, mplsLspState INTEGER, mplsLspRole INTEGER, mplsLspForwardXCId DisplayString, mplsLspReverseXCId DisplayString, mplsLspPriority INTEGER, mplsLspSrcNodeId Unsigned32, mplsLspDestNodeId Unsigned32, mplsLspSrcTunnelId Unsigned32, mplsLspDestTunnelId Unsigned32, mplsLspLspId Unsigned32, mplsLspExtId DisplayString, mplsLspIntTunnelId DisplayString, mplsLspRowStatus RowStatus, mplsLspBFDSession DisplayString, mplsLspCreateBFD CommandString, mplsLspTrafficClass Unsigned32, mplsLspGlobalId Unsigned32, mplsLspDestGlobalId Unsigned32, mplsLspReservedBW Unsigned32, mplsLspDescr DisplayString, mplsLspCreateBFDAdvanced CommandString } mplsLspIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary index assigned to each entry. " ::= { mplsLspEntry 1 } mplsLspName OBJECT-TYPE SYNTAX MgmtNameString MAX-ACCESS read-only STATUS current DESCRIPTION "The management name of the entry, for example 'lsp:1:2:identifier', where the first number indicates subrack, the second slot number and the third is the unique identifier. " ::= { mplsLspEntry 2 } mplsLspInternalReference OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "For internal use only. " DEFVAL { 0 } ::= { mplsLspEntry 3 } mplsLspIdentifier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "A unique identifier for the LSP object. " DEFVAL { "" } ::= { mplsLspEntry 4 } mplsLspState OBJECT-TYPE SYNTAX INTEGER { up (1), down (2), unknown (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The indicated state of the LSP. up - The LSP is active and the connection has been verified. down - The LSP is not active, or the connection has not been verified. unknown - The LSP connectivity can not be verified. " DEFVAL { 3 } ::= { mplsLspEntry 5 } mplsLspRole OBJECT-TYPE SYNTAX INTEGER { edge (1), transit (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The entry signifies the role the LSP entry represents. edge - The LSP is originated and terminated in the node, which is considered a Label edge router, LER. transit - The LSP is not originated in the node, which is considered a Label switch router, LSR. " DEFVAL { 1 } ::= { mplsLspEntry 6 } mplsLspForwardXCId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The identifier for the outgoing XC entry in a LER. For a LSR transit LSP, the terms forward and reverse have no significance, and the forward XC indicates one direction of the bidirectional LSP. " DEFVAL { "" } ::= { mplsLspEntry 7 } mplsLspReverseXCId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The identifier for the incoming XC entry in a LER. For a LSR transit LSP, the terms forward and reverse have no significance, and the reverse XC indicates one direction of the bidirectional LSP. " DEFVAL { "" } ::= { mplsLspEntry 8 } mplsLspPriority OBJECT-TYPE SYNTAX Integer32 (1..2) MAX-ACCESS read-create STATUS current DESCRIPTION "The entry signifies the priority of the LSP within the tunnel. 1 - Highest priority, working LSP in a revertive protected tunnel with multiple LSPs. 2 - Second highest priority, protecting LSP in a revertive protected tunnel with multiple LSPs. The first LSP created in a tunnel will receive the highest priority and be regarded a the working LSP. " DEFVAL { 1 } ::= { mplsLspEntry 9 } mplsLspSrcNodeId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION " The ID of the source node of the LSP, i.e. the node where this LSP originates. Used for externally uniquely identifying the LSP in the standardized format, '[Src node ID]:[SrcTunnelId]-[Dest. Node ID]:[DestTunnelId][LSPNum]'. A zero value indicates that the node ID is not set. This value can be changed in the MPLS node page. This value can be set in the MPLS node settings page. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsLspEntry 10 } mplsLspDestNodeId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION " The ID of the destination node of the LSP, i.e. the node where this LSP terminates. Used for externally uniquely identifying the LSP in the standardized format. '[Src global ID]:[Src node ID]:[Src Tunnel ID]:[Src LSP ID]- [Dest global ID]:[Dest. Node ID]:[Dest Tunnel ID]:[Dest LSP ID]'. A zero value indicates that the node ID is not set. This value can be set in the MPLS node settings page. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsLspEntry 11 } mplsLspSrcTunnelId OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " The source node MPLS-TP tunnel ID of the tunnel that this LSP is a part of. Used for externally uniquely identifying the LSP in the standardized format. '[Src Global ID]:[Src Node ID]:[Src Tunnel ID]:[Src LSP ID]- [Dest Global ID]:[Dest. Node ID]:[Dest Tunnel ID]:[Dest LSP ID]'. A zero value indicates that the tunnel ID is not set. This value can be changed in the associated tunnel page. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsLspEntry 12 } mplsLspDestTunnelId OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " The destination node MPLS-TP tunnel ID of the tunnel that this LSP is a part of. Used for externally uniquely identifying the LSP in the standardized format, '[Src Global ID]:[Src Node ID]:[Src Tunnel ID]:[Src LSP ID]- [Dest Global ID]:[Dest. Node ID]:[Dest Tunnel ID]:[Dest LSP ID]'. A zero value indicates that the tunnel ID is not set. This value can be changed in the associated tunnel page. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsLspEntry 13 } mplsLspLspId OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION " The ID of the LSP, used for externally uniquely identifying the LSP in the standardized format, '[Src Global ID]:[Src Node ID]:[Src Tunnel ID]:[Src LSP ID]- [Dest Global ID]:[Dest. Node ID]:[Dest Tunnel ID]:[Dest LSP ID]'. This value is automatically updated when the LSP is associated with a tunnel. A working LSP will get the ID value = 1 and protecting LSP will get the ID value = 2. A zero value indicates that the LSP ID is not set. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { 0 } ::= { mplsLspEntry 14 } mplsLspExtId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " The ID string of the LSP, used for externally uniquely identifying the LSP in the standardized format, '[Src Global ID]:[Src Node ID]:[Src Tunnel ID]:[Src LSP ID]- [Dest Global ID]:[Dest. Node ID]:[Dest Tunnel ID]:[Dest LSP ID]'. An empty string indicates that the LSP ID is not set. " REFERENCE "MPLS-TP Identifiers [TPIDS]" DEFVAL { "" } ::= { mplsLspEntry 15 } mplsLspIntTunnelId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION " The Internal ID of the MPLS-TP tunnel that the LSP is a part of. This entry is used for internal cross-reference between tunnels and LSPs. " DEFVAL { "" } ::= { mplsLspEntry 16 } mplsLspRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Manages creation and deletion of conceptual rows. See also SNMPv2-TC. Note: The newly created object will not necessarily receive the same index as used in the create procedure. " ::= { mplsLspEntry 17 } mplsLspBFDSession OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION " The Internal ID of the BFD session the LSP that is monitoring the LSP data connections. This entry is used for internal cross-reference between BFD sessions and LSPs. " DEFVAL { "" } ::= { mplsLspEntry 18 } mplsLspCreateBFD OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command to create a BFD session object and connect it to an LSP. BFD Template - Select preferred BFD template to setup timing of BFD session. Admin status - Set the initial state of the BFD session administrative status on creation. " ::= { mplsLspEntry 19 } mplsLspTrafficClass OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-create STATUS deprecated DESCRIPTION " The entry signifies the Traffic Class. " DEFVAL { 4 } ::= { mplsLspEntry 20 } mplsLspGlobalId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "This object allows the administrator to assign a unique operator identifier also called MPLS-TP Global Identifier. The Global Identifier can contain the 2-octet or 4-octet value of the operators Autonomous System Number (ASN). The value zero indicates that the value is not initialized but will work inside a single carrier network. The value zero indicates that the value is not initialized but will work inside a single carrier network. This value can be set in the MPLS node settings page. " REFERENCE "MPLS-TP Identifiers" DEFVAL { 0 } ::= { mplsLspEntry 21 } mplsLspDestGlobalId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "This object allows the administrator to assign a unique operator identifier also called MPLS-TP Global Identifier. The Global Identifier can contain the 2-octet or 4-octet value of the operators Autonomous System Number (ASN). The value zero indicates that the value is not initialized but will work inside a single carrier network. This value can be set in the MPLS tunnel settings page. " REFERENCE "MPLS-TP Identifiers" DEFVAL { 0 } ::= { mplsLspEntry 22 } mplsLspReservedBW OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Bandwidth reserved by the LSP. Default value is 0 and inidcates that no bandwidth has been allocated by the LSP. " DEFVAL { 0 } ::= { mplsLspEntry 23 } mplsLspDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "User configurable label. " DEFVAL { "" } ::= { mplsLspEntry 24 } mplsLspCreateBFDAdvanced OBJECT-TYPE SYNTAX CommandString MAX-ACCESS read-only STATUS current DESCRIPTION "Internal command to create a BFD session object and connect it to an LSP. BFD Template - Select preferred BFD template to setup timing of BFD session. Admin status - Set the initial state of the BFD session administrative status on creation. " ::= { mplsLspEntry 25 } -- ---------------------------------------------------- -- Notifications -- ---------------------------------------------------- -- ---------------------------------------------------- -- Object and event groups -- ---------------------------------------------------- mplsGeneralGroupV1 OBJECT-GROUP OBJECTS { mplsGeneralLastChangeTime, mplsGeneralStateLastChangeTime, mplsGeneralMplsIfTableSize, mplsGeneralMplsXCTableSize, mplsGeneralMplsTunnelTableSize, mplsGeneralMplsLspTableSize, mplsGeneralMplsTnlXLspTableSize} STATUS current DESCRIPTION "The general objects." ::= { lumMplsGroups 1 } mplsIfGroupV1 OBJECT-GROUP OBJECTS { mplsIfIndex, mplsIfName, mplsIfSubrack, mplsIfSlot, mplsIfTxPort, mplsIfPortIndex, mplsIfPortName, mplsIfInternalReference, mplsIfAdminStatus, mplsIfIdentifier, mplsIfNextHopMacAddress, mplsIfInterfaceMacAddress, mplsIfVlan, mplsIfRowStatus} STATUS deprecated DESCRIPTION "The MPLS if objects (R18.0)." ::= { lumMplsGroups 2 } mplsXCGroupV1 OBJECT-GROUP OBJECTS { mplsXCIndex, mplsXCName, mplsXCInternalReference, mplsXCIdentifier, mplsXCInSegmentIfIndex, mplsXCInSegmentIfName, mplsXCInSegmentLabel, mplsXCOutSegmentIfIndex, mplsXCOutSegmentIfName, mplsXCOutSegmentLabel, mplsXCRowStatus } STATUS current DESCRIPTION "The MPLS cross-connect objects (R18.0)." ::= { lumMplsGroups 3 } mplsTunnelGroupV1 OBJECT-GROUP OBJECTS { mplsTunnelIndex, mplsTunnelInternalReference, mplsTunnelIdentifier, mplsTunnelName, mplsTunnelActiveLSP, mplsTunnelActiveLspIndex, mplsTunnelSrcNodeId, mplsTunnelSrcTunnelId, mplsTunnelDestNodeId, mplsTunnelDestTunnelId, mplsTunnelExtId, mplsTunnelAssociateLSP, mplsTunnelRowStatus } STATUS deprecated DESCRIPTION "The MPLS tunnel objects (R18.0)." ::= { lumMplsGroups 4 } mplsNodeGroupV1 OBJECT-GROUP OBJECTS { mplsNodeIndex, mplsNodeName, mplsNodeSubrack, mplsNodeSlot, mplsNodeIccIdStr, mplsNodeIdNum, mplsNodeCreateXC, mplsNodeCreateTunnel, mplsNodeCreateLsp, mplsNodeCreatePw, mplsNodeCreateIf} STATUS deprecated DESCRIPTION "The MPLS node objects (R18.0)." ::= { lumMplsGroups 5 } mplsLspGroupV1 OBJECT-GROUP OBJECTS { mplsLspIndex, mplsLspName, mplsLspInternalReference, mplsLspIdentifier, mplsLspState, mplsLspRole, mplsLspForwardXCId, mplsLspReverseXCId, mplsLspPriority, mplsLspSrcNodeId, mplsLspDestNodeId, mplsLspSrcTunnelId, mplsLspDestTunnelId, mplsLspLspId, mplsLspExtId, mplsLspIntTunnelId, mplsLspRowStatus} STATUS deprecated DESCRIPTION "The MPLS LSP objects (R18.0)." ::= { lumMplsGroups 6 } mplsTnlXLspV1 OBJECT-GROUP OBJECTS { mplsTnlXLspIndex, mplsTnlXLspName, mplsTnlXLspInternalReference, mplsTnlXLspTunnelId, mplsTnlXLspLspId, mplsTnlXLspRowStatus} STATUS current DESCRIPTION "The MPLS tunnel LSP cross reference table (R18.0)." ::= { lumMplsGroups 7 } mplsTunnelGroupV2 OBJECT-GROUP OBJECTS { mplsTunnelIndex, mplsTunnelInternalReference, mplsTunnelIdentifier, mplsTunnelName, mplsTunnelActiveLSP, mplsTunnelActiveLspIndex, mplsTunnelSrcNodeId, mplsTunnelSrcTunnelId, mplsTunnelDestNodeId, mplsTunnelDestTunnelId, mplsTunnelExtId, mplsTunnelAssociateLSP, mplsTunnelRowStatus, mplsTunnelLinearProtection, mplsTunnelProtectionState, mplsTunnelAssociateLinearProt, mplsTunnelGlobalId, mplsTunnelDestGlobalId, mplsTunnelWorkingLSP, mplsTunnelProtectionLSP } STATUS deprecated DESCRIPTION "The MPLS tunnel objects (R19.0)." ::= { lumMplsGroups 8 } mplsNodeGroupV2 OBJECT-GROUP OBJECTS { mplsNodeIndex, mplsNodeName, mplsNodeSubrack, mplsNodeSlot, mplsNodeIccIdStr, mplsNodeIdNum, mplsNodeCreateXC, mplsNodeCreateTunnel, mplsNodeCreateLsp, mplsNodeCreatePw, mplsNodeCreateIf, mplsNodeLinearProtMode, mplsNodeLinearProtWtrTimer, mplsNodeLPContMsgInterval, mplsNodeLPRapidMsgInterval } STATUS deprecated DESCRIPTION "The MPLS node objects (R19.0)." ::= { lumMplsGroups 9 } mplsLspGroupV2 OBJECT-GROUP OBJECTS { mplsLspIndex, mplsLspName, mplsLspInternalReference, mplsLspIdentifier, mplsLspState, mplsLspRole, mplsLspForwardXCId, mplsLspReverseXCId, mplsLspPriority, mplsLspSrcNodeId, mplsLspDestNodeId, mplsLspSrcTunnelId, mplsLspDestTunnelId, mplsLspLspId, mplsLspExtId, mplsLspIntTunnelId, mplsLspRowStatus, mplsLspBFDSession, mplsLspCreateBFD, mplsLspTrafficClass, mplsLspGlobalId, mplsLspDestGlobalId} STATUS deprecated DESCRIPTION "The MPLS LSP objects (R19.0)." ::= { lumMplsGroups 10 } mplsNodeGroupV3 OBJECT-GROUP OBJECTS { mplsNodeIndex, mplsNodeName, mplsNodeSubrack, mplsNodeSlot, mplsNodeIccIdStr, mplsNodeIdNum, mplsNodeCreateXC, mplsNodeCreateTunnel, mplsNodeCreateLsp, mplsNodeCreatePw, mplsNodeCreateIf, mplsNodeLinearProtMode, mplsNodeLinearProtWtrTimer, mplsNodeLPContMsgInterval, mplsNodeLPRapidMsgInterval, mplsNodeCreateMsPw } STATUS deprecated DESCRIPTION "The MPLS node objects (R20.0)." ::= { lumMplsGroups 11 } mplsTunnelGroupV3 OBJECT-GROUP OBJECTS { mplsTunnelIndex, mplsTunnelInternalReference, mplsTunnelIdentifier, mplsTunnelName, mplsTunnelActiveLSP, mplsTunnelActiveLspIndex, mplsTunnelSrcNodeId, mplsTunnelSrcTunnelId, mplsTunnelDestNodeId, mplsTunnelDestTunnelId, mplsTunnelExtId, mplsTunnelAssociateLSP, mplsTunnelRowStatus, mplsTunnelLinearProtection, mplsTunnelProtectionState, mplsTunnelAssociateLinearProt, mplsTunnelGlobalId, mplsTunnelDestGlobalId, mplsTunnelWorkingLSP, mplsTunnelProtectionLSP, mplsTunnelReservedBW, mplsTunnelBookedBW} STATUS deprecated DESCRIPTION "The MPLS tunnel objects (R20.0)." ::= { lumMplsGroups 12 } mplsLspGroupV3 OBJECT-GROUP OBJECTS { mplsLspIndex, mplsLspName, mplsLspInternalReference, mplsLspIdentifier, mplsLspState, mplsLspRole, mplsLspForwardXCId, mplsLspReverseXCId, mplsLspPriority, mplsLspSrcNodeId, mplsLspDestNodeId, mplsLspSrcTunnelId, mplsLspDestTunnelId, mplsLspLspId, mplsLspExtId, mplsLspIntTunnelId, mplsLspRowStatus, mplsLspBFDSession, mplsLspCreateBFD, mplsLspTrafficClass, mplsLspGlobalId, mplsLspDestGlobalId, mplsLspReservedBW} STATUS deprecated DESCRIPTION "The MPLS LSP objects (R20.0)." ::= { lumMplsGroups 13 } mplsNodeGroupV4 OBJECT-GROUP OBJECTS { mplsNodeIndex, mplsNodeName, mplsNodeSubrack, mplsNodeSlot, mplsNodeIccIdStr, mplsNodeIdNum, mplsNodeCreateXC, mplsNodeCreateTunnel, mplsNodeCreateLsp, mplsNodeCreatePw, mplsNodeCreateIf, mplsNodeLinearProtMode, mplsNodeLinearProtWtrTimer, mplsNodeLPContMsgInterval, mplsNodeLPRapidMsgInterval, mplsNodeCreateMsPw, mplsNodeCreateLsp2 } STATUS deprecated DESCRIPTION "The MPLS node objects (R23.0)." ::= { lumMplsGroups 14 } mplsLspGroupV4 OBJECT-GROUP OBJECTS { mplsLspIndex, mplsLspName, mplsLspInternalReference, mplsLspIdentifier, mplsLspState, mplsLspRole, mplsLspForwardXCId, mplsLspReverseXCId, mplsLspPriority, mplsLspSrcNodeId, mplsLspDestNodeId, mplsLspSrcTunnelId, mplsLspDestTunnelId, mplsLspLspId, mplsLspExtId, mplsLspIntTunnelId, mplsLspRowStatus, mplsLspBFDSession, mplsLspCreateBFD, mplsLspTrafficClass, mplsLspGlobalId, mplsLspDestGlobalId, mplsLspReservedBW, mplsLspDescr} STATUS deprecated DESCRIPTION "The MPLS LSP objects (R24.0)." ::= { lumMplsGroups 15 } mplsTunnelGroupV4 OBJECT-GROUP OBJECTS { mplsTunnelIndex, mplsTunnelInternalReference, mplsTunnelIdentifier, mplsTunnelName, mplsTunnelActiveLSP, mplsTunnelActiveLspIndex, mplsTunnelSrcNodeId, mplsTunnelSrcTunnelId, mplsTunnelDestNodeId, mplsTunnelDestTunnelId, mplsTunnelExtId, mplsTunnelAssociateLSP, mplsTunnelRowStatus, mplsTunnelLinearProtection, mplsTunnelProtectionState, mplsTunnelAssociateLinearProt, mplsTunnelGlobalId, mplsTunnelDestGlobalId, mplsTunnelWorkingLSP, mplsTunnelProtectionLSP, mplsTunnelReservedBW, mplsTunnelBookedBW, mplsTunnelDescr} STATUS current DESCRIPTION "The MPLS tunnel objects (R24.0)." ::= { lumMplsGroups 16 } mplsIfGroupV2 OBJECT-GROUP OBJECTS { mplsIfIndex, mplsIfName, mplsIfSubrack, mplsIfSlot, mplsIfTxPort, mplsIfPortIndex, mplsIfPortName, mplsIfInternalReference, mplsIfAdminStatus, mplsIfIdentifier, mplsIfNextHopMacAddress, mplsIfInterfaceMacAddress, mplsIfVlan, mplsIfRowStatus, mplsIfIfNo, mplsIfResourceType, mplsIfLagId} STATUS current DESCRIPTION "The MPLS if objects (R28.0)." ::= { lumMplsGroups 17 } mplsNodeGroupV5 OBJECT-GROUP OBJECTS { mplsNodeIndex, mplsNodeName, mplsNodeSubrack, mplsNodeSlot, mplsNodeIccIdStr, mplsNodeIdNum, mplsNodeCreateXC, mplsNodeCreateTunnel, mplsNodeCreateLsp, mplsNodeCreatePw, mplsNodeCreateIf, mplsNodeLinearProtMode, mplsNodeLinearProtWtrTimer, mplsNodeLPContMsgInterval, mplsNodeLPRapidMsgInterval, mplsNodeCreateMsPw, mplsNodeCreateLsp2, mplsNodeCreateTunnelAdvanced, mplsNodeCreateLspAdvanced, mplsNodeCreatePwGeneric, mplsNodeCreatePwMpls, mplsNodeCreatePwEnet, mplsNodeCreateBfdTemplate, mplsNodeCreateXCAdvanced} STATUS current DESCRIPTION "The MPLS node objects (R30.1)." ::= { lumMplsGroups 18 } mplsLspGroupV5 OBJECT-GROUP OBJECTS { mplsLspIndex, mplsLspName, mplsLspInternalReference, mplsLspIdentifier, mplsLspState, mplsLspRole, mplsLspForwardXCId, mplsLspReverseXCId, mplsLspPriority, mplsLspSrcNodeId, mplsLspDestNodeId, mplsLspSrcTunnelId, mplsLspDestTunnelId, mplsLspLspId, mplsLspExtId, mplsLspIntTunnelId, mplsLspRowStatus, mplsLspBFDSession, mplsLspCreateBFD, mplsLspTrafficClass, mplsLspGlobalId, mplsLspDestGlobalId, mplsLspReservedBW, mplsLspDescr, mplsLspCreateBFDAdvanced} STATUS current DESCRIPTION "The MPLS LSP objects (R30.1)." ::= { lumMplsGroups 19 } -- ---------------------------------------------------- -- Compliance -- ---------------------------------------------------- lumMplsBasicComplV1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R18.0)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV1, mplsXCGroupV1, mplsTunnelGroupV2, mplsNodeGroupV1, mplsLspGroupV1, mplsTnlXLspV1 } ::= { lumMplsCompl 1 } lumMplsBasicComplV2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R19.0)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV1, mplsXCGroupV1, mplsTunnelGroupV2, mplsNodeGroupV2, mplsLspGroupV2, mplsTnlXLspV1} ::= { lumMplsCompl 2 } lumMplsBasicComplV3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R20.0)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV1, mplsXCGroupV1, mplsTunnelGroupV3, mplsNodeGroupV3, mplsLspGroupV3, mplsTnlXLspV1} ::= { lumMplsCompl 3 } lumMplsBasicComplV4 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R21.0)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV1, mplsXCGroupV1, mplsTunnelGroupV3, mplsNodeGroupV3, mplsLspGroupV3, mplsTnlXLspV1} ::= { lumMplsCompl 4 } lumMplsBasicComplV5 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R21.0)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV1, mplsXCGroupV1, mplsTunnelGroupV3, mplsNodeGroupV4, mplsLspGroupV3, mplsTnlXLspV1} ::= { lumMplsCompl 5 } lumMplsBasicComplV6 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R24.0)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV1, mplsXCGroupV1, mplsTunnelGroupV4, mplsNodeGroupV4, mplsLspGroupV4, mplsTnlXLspV1} ::= { lumMplsCompl 6 } lumMplsBasicComplV7 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R28.0)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV2, mplsXCGroupV1, mplsTunnelGroupV4, mplsNodeGroupV4, mplsLspGroupV4, mplsTnlXLspV1} ::= { lumMplsCompl 7 } lumMplsBasicComplV8 MODULE-COMPLIANCE STATUS current DESCRIPTION "Basic implementation requirements for the MPLS MIB. (R30.1)" MODULE MANDATORY-GROUPS { mplsGeneralGroupV1, mplsIfGroupV2, mplsXCGroupV1, mplsTunnelGroupV4, mplsNodeGroupV5, mplsLspGroupV5, mplsTnlXLspV1} ::= { lumMplsCompl 8 } END