-- ******************************************************************* -- CISCO-LWAPP-DOT11-CLIENT-CCX-REPORTS-MIB.my: -- Light Weight Access Point Wireless client reports -- MIB -- June 2006, Ambika Prasad Mohanty -- -- Copyright (c) 2006, 2006, 2010 by Cisco Systems Inc. -- All rights reserved. -- ******************************************************************* CISCO-LWAPP-DOT11-CLIENT-CCX-REPORTS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF RowStatus, MacAddress, TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC cldcClientMacAddress FROM CISCO-LWAPP-DOT11-CLIENT-MIB ciscoMgmt FROM CISCO-SMI; ciscoLwappDot11ClientRmMIB MODULE-IDENTITY LAST-UPDATED "201012130000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Cisco Compatible eXtensions (CCX) Wireless LAN Access Points (APs) manufactured by Cisco Systems have features and capabilities beyond those in related standards (e.g., IEEE 802.11 suite of standards, Wi-Fi recommendations by WECA, 802.1X security suite, etc). A number of features provide higher performance. For example, Cisco AP transmits a specific Information Element, which the clients adapt to for enhanced performance. Similarly, a number of features are implemented by means of proprietary Information Elements, which Cisco clients use in specific ways to carry out tasks above and beyond the standard. Other examples of feature categories are roaming and power saving. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. The terms 'Mobile node' and 'client' are used interchangeably. Radio Management (RM) This term refers to managing the 802.11 radio environment to provide the best quality service to to the 802.11 wireless clients. Service Set Identifier ( SSID ) SSID is a unique identifier that APs and clients use to identify with each other. SSID is a simple means of access control and is not for security. The SSID can be any alphanumeric entry up to 32 characters. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol" REVISION "201012130000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 767 } ciscoLwapDot11ClientRmMIBNotifs OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIB 0 } ciscoLwappDot11ClientRmMIBObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIB 1 } ciscoLwappDot11ClientRmMIBConform OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIB 2 } cldccrRmReq OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIBObjects 1 } cldccrRmResp OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIBObjects 2 } cldccrRmReqStatus OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIBObjects 3 } -- ****************************************************************** -- ****************************************************************** CiscoLwappCcxRmReqStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This attribute is used to initiate/track a request to the ccxv4 client." SYNTAX INTEGER { inProgress(1), success(2), failure(3) } cldccrRmReqTable OBJECT-TYPE SYNTAX SEQUENCE OF CldccrRmReqEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure the radio measurement request parameters to be sent to the ccxv4 clients." ::= { cldccrRmReq 1 } cldccrRmReqEntry OBJECT-TYPE SYNTAX CldccrRmReqEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table. An entry corresponds to a client for which a certain type of report is being fetched." INDEX { cldcClientMacAddress } ::= { cldccrRmReqTable 1 } CldccrRmReqEntry ::= SEQUENCE { cldccrRmReqReportType BITS, cldccrRmInitiateReq TruthValue, cldccrRmReqNumIterations INTEGER, cldccrRmReqMeasDuration Unsigned32, cldccrRmReqRowStatus RowStatus } cldccrRmReqReportType OBJECT-TYPE SYNTAX BITS { channelLoadReport(0), histogramReport(1), beaconReport(2), frameReport(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object is set to list of radio measurement requests the reports of which will be sent by the ccxv4 client to the controller." ::= { cldccrRmReqEntry 1 } cldccrRmInitiateReq OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to send the rm req message to the client." ::= { cldccrRmReqEntry 2 } cldccrRmReqNumIterations OBJECT-TYPE SYNTAX INTEGER (0..250) MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute is used to set the number of times the rm request will be sent to the client." ::= { cldccrRmReqEntry 3 } cldccrRmReqMeasDuration OBJECT-TYPE SYNTAX Unsigned32 (5..32400) MAX-ACCESS read-create STATUS current DESCRIPTION "The time interval between two RM Reqs in seconds." ::= { cldccrRmReqEntry 4 } cldccrRmReqRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This is the status column for this row and is used to create and delete specific instances of rows in this table." ::= { cldccrRmReqEntry 5 } cldccrRmHistRepTable OBJECT-TYPE SYNTAX SEQUENCE OF CldccrRmHistRepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the noise histogram reports of the clients which were queried for the same." ::= { cldccrRmResp 1 } cldccrRmHistRepEntry OBJECT-TYPE SYNTAX CldccrRmHistRepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in the table where entry is identified by the client Mac address." INDEX { cldcClientMacAddress, cldccrRmHistIndex } ::= { cldccrRmHistRepTable 1 } CldccrRmHistRepEntry ::= SEQUENCE { cldccrRmHistIndex Unsigned32, cldccrRmHistRepChannelNumber Unsigned32, cldccrRmHistRepTimeStamp OCTET STRING, cldccrRmHistRepRPIDensity0 Unsigned32, cldccrRmHistRepRPIDensity1 Unsigned32, cldccrRmHistRepRPIDensity2 Unsigned32, cldccrRmHistRepRPIDensity3 Unsigned32, cldccrRmHistRepRPIDensity4 Unsigned32, cldccrRmHistRepRPIDensity5 Unsigned32, cldccrRmHistRepRPIDensity6 Unsigned32, cldccrRmHistRepRPIDensity7 Unsigned32 } cldccrRmHistIndex OBJECT-TYPE SYNTAX Unsigned32 (0..28) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index which will be the channel number in most cases." ::= { cldccrRmHistRepEntry 1 } cldccrRmHistRepChannelNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Channel number indicates the channel number to which the noise histogram Report applies." ::= { cldccrRmHistRepEntry 2 } cldccrRmHistRepTimeStamp OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Timestamp of the histogram report." ::= { cldccrRmHistRepEntry 3 } cldccrRmHistRepRPIDensity0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range power << -87 db." ::= { cldccrRmHistRepEntry 4 } cldccrRmHistRepRPIDensity1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range -87 < power << -82." ::= { cldccrRmHistRepEntry 5 } cldccrRmHistRepRPIDensity2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range -82 < power << -77." ::= { cldccrRmHistRepEntry 6 } cldccrRmHistRepRPIDensity3 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range -77 < power << -72." ::= { cldccrRmHistRepEntry 7 } cldccrRmHistRepRPIDensity4 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range -72< Power << -67." ::= { cldccrRmHistRepEntry 8 } cldccrRmHistRepRPIDensity5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range -67< Power << -62." ::= { cldccrRmHistRepEntry 9 } cldccrRmHistRepRPIDensity6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range -62< Power<< -57." ::= { cldccrRmHistRepEntry 10 } cldccrRmHistRepRPIDensity7 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Field stores the RPI density in power range -57< Power<< -52." ::= { cldccrRmHistRepEntry 11 } cldccrRmBeaconRepTable OBJECT-TYPE SYNTAX SEQUENCE OF CldccrRmBeaconRepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the beacon reports of the clients which were queried for the same." ::= { cldccrRmResp 2 } cldccrRmBeaconRepEntry OBJECT-TYPE SYNTAX CldccrRmBeaconRepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in the table where entry is identified by the client Mac address." INDEX { cldcClientMacAddress, cldccrRmBeaconIndex } ::= { cldccrRmBeaconRepTable 1 } CldccrRmBeaconRepEntry ::= SEQUENCE { cldccrRmBeaconIndex Unsigned32, cldccrRmBeaconRptChannelNumber Unsigned32, cldccrRmBeaconRptTimeStamp OCTET STRING, cldccrRmBeaconRptPhyType INTEGER, cldccrRmBeaconRptReceivedPower Unsigned32, cldccrRmBeaconRptBSSID MacAddress, cldccrRmBeaconRptParentTsf OCTET STRING, cldccrRmBeaconRptTargetTsf OCTET STRING, cldccrRmBeaconRptInterval Unsigned32, cldccrRmBeaconRptCapInfo Unsigned32 } cldccrRmBeaconIndex OBJECT-TYPE SYNTAX Unsigned32 (0..28) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index which will be the channel number in most cases." ::= { cldccrRmBeaconRepEntry 1 } cldccrRmBeaconRptChannelNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Channel number indicates the channel number to which the noise beacon report applies." ::= { cldccrRmBeaconRepEntry 2 } cldccrRmBeaconRptTimeStamp OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Timestamp of the beacon report." ::= { cldccrRmBeaconRepEntry 3 } cldccrRmBeaconRptPhyType OBJECT-TYPE SYNTAX INTEGER { fh(1), dss(2), unused(3), ofdm(4), highDataRateDss(5), erp(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Phy type indicates the physical medium used." ::= { cldccrRmBeaconRepEntry 4 } cldccrRmBeaconRptReceivedPower OBJECT-TYPE SYNTAX Unsigned32 (0..250) MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the received strength of the beacon or probe response frame in dBm." ::= { cldccrRmBeaconRepEntry 5 } cldccrRmBeaconRptBSSID OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This field contains the 6-byte BSSID of the STA that transmitted the beacon or probe response frame." ::= { cldccrRmBeaconRepEntry 6 } cldccrRmBeaconRptParentTsf OBJECT-TYPE SYNTAX OCTET STRING (SIZE (64)) MAX-ACCESS read-only STATUS current DESCRIPTION "This field is used to store the parent TSF Parent TSF contains the lower 4 bytes of the serving APs. TSF value at the time the measuring STA received the beacon or probe response frame." ::= { cldccrRmBeaconRepEntry 7 } cldccrRmBeaconRptTargetTsf OBJECT-TYPE SYNTAX OCTET STRING (SIZE (64)) MAX-ACCESS read-only STATUS current DESCRIPTION "This field is used to store the Target TSF. Target TSF contains the 8-byte TSF value contained in the beacon or probe response received by the measuring STA." ::= { cldccrRmBeaconRepEntry 8 } cldccrRmBeaconRptInterval OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is equal to the 2-byte Beacon Interval field in the received beacon or probe response." ::= { cldccrRmBeaconRepEntry 9 } cldccrRmBeaconRptCapInfo OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the capability info." ::= { cldccrRmBeaconRepEntry 10 } cldccRmChannelLoadReportTable OBJECT-TYPE SYNTAX SEQUENCE OF CldccRmChannelLoadReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the channel load reports of the clients which were queried for the same." ::= { cldccrRmResp 3 } cldccRmChannelLoadReportEntry OBJECT-TYPE SYNTAX CldccRmChannelLoadReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in the table where entry is identified by the client Mac address." INDEX { cldcClientMacAddress, cldccRmChannelLoadReportIndex } ::= { cldccRmChannelLoadReportTable 1 } CldccRmChannelLoadReportEntry ::= SEQUENCE { cldccRmChannelLoadReportIndex Unsigned32, cldccRmChannelLoadReportChannelNumber Unsigned32, cldccRmChannelLoadReportTimeStamp OCTET STRING, cldccRmChannelLoadReportCCABusyFraction Unsigned32 } cldccRmChannelLoadReportIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This indicates the index of the report table." ::= { cldccRmChannelLoadReportEntry 1 } cldccRmChannelLoadReportChannelNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Channel Number indicates the channel number to which the Channel Load Report applies." ::= { cldccRmChannelLoadReportEntry 2 } cldccRmChannelLoadReportTimeStamp OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Timestamp of the channel load report." ::= { cldccRmChannelLoadReportEntry 3 } cldccRmChannelLoadReportCCABusyFraction OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "CCA Busy Fraction shall contain the fractional duration over which CCA indicated the channel was busy during the measurement duration." ::= { cldccRmChannelLoadReportEntry 4 } cldccRmFrameReportTable OBJECT-TYPE SYNTAX SEQUENCE OF CldccRmFrameReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the frame reports of the clients which were queried for the same." ::= { cldccrRmResp 4 } cldccRmFrameReportEntry OBJECT-TYPE SYNTAX CldccRmFrameReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in the table where entry is identified by the client Mac address." INDEX { cldcClientMacAddress, cldccRmFrameReportElemIndex, cldccRmFrameReportSubElemIndex } ::= { cldccRmFrameReportTable 1 } CldccRmFrameReportEntry ::= SEQUENCE { cldccRmFrameReportElemIndex Unsigned32, cldccRmFrameReportSubElemIndex Unsigned32, cldccRmFrameReportChanNumber Unsigned32, cldccRmFrameReportTimeStamp OCTET STRING, cldccRmFrameReportTransmitAddr MacAddress, cldccRmFrameReportBssid MacAddress, cldccRmFrameReportRecvSigPower Unsigned32, cldccRmFrameReportFrameCount Unsigned32 } cldccRmFrameReportElemIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This attribute represents the index of element index of frame report." ::= { cldccRmFrameReportEntry 1 } cldccRmFrameReportSubElemIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This attribute represents the index of the sub element in a frame report." ::= { cldccRmFrameReportEntry 2 } cldccRmFrameReportChanNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the channel number of frame report." ::= { cldccRmFrameReportEntry 3 } cldccRmFrameReportTimeStamp OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Timestamp of the frame report." ::= { cldccRmFrameReportEntry 4 } cldccRmFrameReportTransmitAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This represents the transmitted address." ::= { cldccRmFrameReportEntry 5 } cldccRmFrameReportBssid OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This represents the bssid." ::= { cldccRmFrameReportEntry 6 } cldccRmFrameReportRecvSigPower OBJECT-TYPE SYNTAX Unsigned32 (0..250) MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the received strength of the beacon or probe response frame in dBm." ::= { cldccRmFrameReportEntry 7 } cldccRmFrameReportFrameCount OBJECT-TYPE SYNTAX Unsigned32 (0..250) MAX-ACCESS read-only STATUS current DESCRIPTION "This field indicates the received strength of the beacon or probe response frame in dBm." ::= { cldccRmFrameReportEntry 8 } cldccrRmReqStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CldccrRmReqStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to get the status for each of the reports." ::= { cldccrRmReqStatus 1 } cldccrRmReqStatusEntry OBJECT-TYPE SYNTAX CldccrRmReqStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in the table where entry is identified by the client Mac address." INDEX { cldcClientMacAddress } ::= { cldccrRmReqStatusTable 1 } CldccrRmReqStatusEntry ::= SEQUENCE { cldccrRmFrameReqStatus CiscoLwappCcxRmReqStatus, cldccrRmHistogramReqStatus CiscoLwappCcxRmReqStatus, cldccrRmBeaconReqStatus CiscoLwappCcxRmReqStatus, cldccrRmChanLoadReqStatus CiscoLwappCcxRmReqStatus } cldccrRmFrameReqStatus OBJECT-TYPE SYNTAX CiscoLwappCcxRmReqStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is used to initiate/track a frame report request to the ccxv4 client." ::= { cldccrRmReqStatusEntry 1 } cldccrRmHistogramReqStatus OBJECT-TYPE SYNTAX CiscoLwappCcxRmReqStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is used to initiate/track a noise histogram request to the ccxv4 client." ::= { cldccrRmReqStatusEntry 2 } cldccrRmBeaconReqStatus OBJECT-TYPE SYNTAX CiscoLwappCcxRmReqStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is used to initiate/track a beacon request to the ccxv4 client." ::= { cldccrRmReqStatusEntry 3 } cldccrRmChanLoadReqStatus OBJECT-TYPE SYNTAX CiscoLwappCcxRmReqStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is used to initiate/track a channel load request to the ccxv4 client." ::= { cldccrRmReqStatusEntry 4 } -- ******************************************************************** -- * Compliance statements -- ******************************************************************** ciscoLwappDot11ClientRmMIBCompliances OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIBConform 1 } ciscoLwappDot11ClientRmMIBGroups OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientRmMIBConform 2 } ciscoLwappDot11ClientRmMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappDot11ClientRmMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappDot11ClientRmConfigGroup } ::= { ciscoLwappDot11ClientRmMIBCompliances 1 } -- ******************************************************************** -- * Units of conformance -- ******************************************************************** ciscoLwappDot11ClientRmConfigGroup OBJECT-GROUP OBJECTS { cldccrRmReqReportType, cldccrRmInitiateReq, cldccrRmReqNumIterations, cldccrRmReqMeasDuration, cldccrRmReqRowStatus, cldccrRmHistRepChannelNumber, cldccrRmHistRepTimeStamp, cldccrRmHistRepRPIDensity0, cldccrRmHistRepRPIDensity1, cldccrRmHistRepRPIDensity2, cldccrRmHistRepRPIDensity3, cldccrRmHistRepRPIDensity4, cldccrRmHistRepRPIDensity5, cldccrRmHistRepRPIDensity6, cldccrRmHistRepRPIDensity7, cldccrRmBeaconRptChannelNumber, cldccrRmBeaconRptTimeStamp, cldccrRmBeaconRptPhyType, cldccrRmBeaconRptReceivedPower, cldccrRmBeaconRptBSSID, cldccrRmBeaconRptParentTsf, cldccrRmBeaconRptTargetTsf, cldccrRmBeaconRptInterval, cldccrRmBeaconRptCapInfo, cldccRmChannelLoadReportChannelNumber, cldccRmChannelLoadReportTimeStamp, cldccRmChannelLoadReportCCABusyFraction, cldccRmFrameReportChanNumber, cldccRmFrameReportTimeStamp, cldccRmFrameReportTransmitAddr, cldccRmFrameReportBssid, cldccRmFrameReportRecvSigPower, cldccRmFrameReportFrameCount, cldccrRmFrameReqStatus, cldccrRmHistogramReqStatus, cldccrRmBeaconReqStatus, cldccrRmChanLoadReqStatus } STATUS current DESCRIPTION "This collection of objects represent the reports of the CCX Clients." ::= { ciscoLwappDot11ClientRmMIBGroups 1 } END