ALCATEL-IND1-E-SERVICE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-IDENTITY, OBJECT-TYPE, Integer32, Counter64 FROM SNMPv2-SMI Counter32 FROM SNMPv2-SMI OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF softentIND1eService FROM ALCATEL-IND1-BASE RowStatus, TEXTUAL-CONVENTION, DisplayString, MacAddress FROM SNMPv2-TC InterfaceIndex FROM IF-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB ; alcatelIND1EServiceMIB MODULE-IDENTITY LAST-UPDATED "200912160000Z" ORGANIZATION "Alcatel-Lucent" CONTACT-INFO "Please consult with Customer Service to ensure the most appropriate version of this document is used with the products in question: Alcatel-Lucent, Enterprise Solutions Division (Formerly Alcatel Internetworking, Incorporated) 26801 West Agoura Road Agoura Hills, CA 91301-5122 United States Of America Telephone: North America +1 800 995 2696 Latin America +1 877 919 9526 Europe +31 23 556 0100 Asia +65 394 7933 All Other +1 818 878 4507 Electronic Mail: support@ind.alcatel.com World Wide Web: http://alcatel-lucent.com/wps/portal/enterprise File Transfer Protocol: ftp://ftp.ind.alcatel.com/pub/products/mibs" DESCRIPTION "The parameters for configuration of the E-Service feature. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2006 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE" REVISION "201001190000Z" DESCRIPTION "The below listed objects are made as read-create in 6.6.1.680.R01 Post GA. alaEServiceUNIProfile8021xTreatment, alaEServiceUNIProfile8021ABTreatment, alaEServiceUNIProfile8023adTreatment & alaEServiceUNIProfileAmapTreatment." ::= { softentIND1eService 1} -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- Textual Conventions -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx AlaEServiceUNIProfileProtocolTreatment ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The behavior of the bridge in regards to the given protocols packets received on the UNI. Tunnel (1) enables the packets to be tunneled across the provider network. Discard (2) causes the packets to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling." SYNTAX INTEGER { tunnel (1), drop (2), peer (3), macTunnel (4) } AlaEServiceL2CustomProtocolType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of the custom L2 protocol entry is defined by this mib object. mask-type (1) - specifies a MAC+Mask entry mac-type (2) - specifies a MAC alone entry ssapdsap-type (3) - specifies a MAC+SSAP/DSAP+PID entry ether-type (4) - specifies a MAC+ETHERTYPE entry." SYNTAX INTEGER { maskType (1), macType (2), ssapdsapType (3), etherType (4), ethersubType (5) } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alcatelIND1eServiceMIBObjects OBJECT-IDENTITY STATUS current DESCRIPTION "Branch For E-Service Managed Objects." ::= { alcatelIND1EServiceMIB 1 } alcatelIND1EServiceMIBConformance OBJECT-IDENTITY STATUS current DESCRIPTION "Branch For E-Service Conformance Information." ::= { alcatelIND1EServiceMIB 2 } alcatelIND1EServiceMIBGroups OBJECT-IDENTITY STATUS current DESCRIPTION "Branch For E-Service Units Of Conformance." ::= { alcatelIND1EServiceMIBConformance 1 } alcatelIND1EServiceMIBCompliances OBJECT-IDENTITY STATUS current DESCRIPTION "Branch For E-Service Compliance Statements." ::= { alcatelIND1EServiceMIBConformance 2 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service Group alaEService OBJECT IDENTIFIER ::= { alcatelIND1eServiceMIBObjects 1 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceInfo OBJECT IDENTIFIER ::= { alaEService 1 } alaEServiceMode OBJECT-TYPE SYNTAX INTEGER { legacyMode (1), eServiceMode (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current mode configured for Vlan Stacking and Layer 2 tunnel configuration. legacyMode (1) indicates that the commands from AlcatelIND1VLANStacking.mib are to be used. eServiceMode (2) indicates the commands from this MIB are to be used." DEFVAL { legacyMode } ::= { alaEServiceInfo 1 } alaEServiceStatReset OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the global clear statistics control for ethernet-service counters. default(0) - default value for this object, reset(1) - indicates that all ethernet-service counters should be cleared." DEFVAL { default } ::= { alaEServiceInfo 2 } alaEServiceL2MacTunnel OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the layer 2 Mac tunnel globaly. enable(1) - MAC tunneling is enabled globally. disable(2) - MAC tunneling is disabled globally." DEFVAL { enable } ::= { alaEServiceInfo 3 } alaEServiceUntaggedMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the status of cvlan on untagged frames feature globally. enable(1) - Untagged Mode is enabled globally. disable(2) - Untagged Mode is disabled globally." DEFVAL { disable } ::= { alaEServiceInfo 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service SAP Profile Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceSapProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceSapProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains service profiles containing performance and control attributes. An entry in this table is created when a new service profile is defined." ::= { alaEService 2 } alaEServiceSapProfileEntry OBJECT-TYPE SYNTAX AlaEServiceSapProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A E-Service Service Profile entry." INDEX { IMPLIED alaEServiceSapProfileID } ::= { alaEServiceSapProfileTable 1 } AlaEServiceSapProfileEntry ::= SEQUENCE { alaEServiceSapProfileID DisplayString, alaEServiceSapProfileCVLANTreatment INTEGER, alaEServiceSapProfileReplacementCVLAN INTEGER, alaEServiceSapProfilePriorityMapMode INTEGER, alaEServiceSapProfileFixedPriority INTEGER, alaEServiceSapProfileIngressBW Integer32, alaEServiceSapProfileBandwidthShare INTEGER, alaEServiceSapProfileRowStatus RowStatus, alaEServiceSapProfileEgressBW Integer32, alaEServiceSapProfileCIR Integer32, alaEServiceSapProfileCBS Integer32, alaEServiceSapProfilePIR Integer32, alaEServiceSapProfilePBS Integer32, alaEServiceSapProfileDepth Integer32 } alaEServiceSapProfileID OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A label given to uniquely identify this profile. Must be at least one character long." ::= { alaEServiceSapProfileEntry 1 } alaEServiceSapProfileCVLANTreatment OBJECT-TYPE SYNTAX INTEGER { stackSVLAN (1), translate (2), changeCVLAN (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of VLAN stacking operation to be performed on a customer frame entering this service. Stack Svlan (1) indicates that the SVLAN is to be pre-pended on the frame before any existing 802.1Q tag. Translate (2) means to replace the existing 802.1Q tag with the SVLAN. Change CVLAN (3) indicates that the customer tag is to remain on the frame but its value is to be changed to the supplied value." DEFVAL { stackSVLAN } ::= { alaEServiceSapProfileEntry 2 } alaEServiceSapProfileReplacementCVLAN OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "The CVLAN ID to use when using the Change CVLAN treatment mode." ::= { alaEServiceSapProfileEntry 3 } alaEServiceSapProfilePriorityMapMode OBJECT-TYPE SYNTAX INTEGER { notAssigned(0), mapInnerPtoOuterP (1), mapInnerDscpToOuterP(2), fixedP (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the source of the value for the priority field of the SVLAN 802.1Q tag when pre-pended to the customer data frame. If set to notAssigned(0), SAP priority limit parameter will not be effective, QoS priority settings needs to be configured. MapInnerPtoOuterP (1) uses the priority field of the incoming frame when tagged to fill in the priority field of the SVLAN tag. mapInnerDscpToOuterP (2) uses the frames priority bits in its IP DSCP field to fill in the priority field of the SVLAN tag. FixedP (3) uses the supplied FixedPriorityValue to fill in the SVLAN tag priority bits." DEFVAL { fixedP } ::= { alaEServiceSapProfileEntry 4 } alaEServiceSapProfileFixedPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the value of the priority field of the 802.1Q SVLAN tag pre-pended to customer data frames when the fixed priority mapping mode is selected." DEFVAL { 0 } ::= { alaEServiceSapProfileEntry 5 } alaEServiceSapProfileIngressBW OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes this limit of ingress bandwidth for the traffic to which this profile is applied. If 0, no bandwidth limit is applied. This number represents traffic in units of 1,000,000 bits per second. Note that all CVLAN that belong to this SAP will share this aggregated limit." ::= { alaEServiceSapProfileEntry 6 } alaEServiceSapProfileBandwidthShare OBJECT-TYPE SYNTAX INTEGER { notApplicable(0), shared (1), notShared(2), notAssigned(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the use of the bandwidth limit in how it is applied across multiple ports of the SAP. If set to notApplicable(0), the SAP is not used. If set to Shared (1), all the ports that are part of the SAP will use aggregated bandwidth, sharing some part of the bandwidth limit. If set to notShared (2), each port will use its own bandwidth meter for this SAP. This value is not used if ingressBandwidth is 0.If set to notAssigned(3), SAP bandwidth limit parameter will not be effective, QoS bandwith settings needs to be configured." DEFVAL { shared } ::= { alaEServiceSapProfileEntry 7 } alaEServiceSapProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry." ::= { alaEServiceSapProfileEntry 8 } alaEServiceSapProfileEgressBW OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes this limit of egress bandwidth for each UNI of the SAP to which this profile is applied. If 0, no bandwidth limit is applied. This number represents traffic in units of Megabits per second. Note that all CVLAN that belong to this SAP will share this aggregated limit." DEFVAL { 0 } ::= { alaEServiceSapProfileEntry 9 } alaEServiceSapProfileCIR OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Committed Information Rate - bandwidth values in bits per second." DEFVAL { 0 } ::= { alaEServiceSapProfileEntry 10 } alaEServiceSapProfileCBS OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Committed Burst Size - bucket size in byte." DEFVAL { 0 } ::= { alaEServiceSapProfileEntry 11 } alaEServiceSapProfilePIR OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Peak Information Rate - bandwidth values in bits per second." DEFVAL { 0 } ::= { alaEServiceSapProfileEntry 12 } alaEServiceSapProfilePBS OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Peak Burst Size - bucket size in byte." DEFVAL { 0 } ::= { alaEServiceSapProfileEntry 13 } alaEServiceSapProfileDepth OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the depth limit." DEFVAL { 0 } ::= { alaEServiceSapProfileEntry 14 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Profile Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceUNIProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains service profiles containing performance and control attributes. An entry in this table is created when a new service profile is defined." ::= { alaEService 3 } alaEServiceUNIProfileEntry OBJECT-TYPE SYNTAX AlaEServiceUNIProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A E-Service Service Profile entry." INDEX { IMPLIED alaEServiceUNIProfileID } ::= { alaEServiceUNIProfileTable 1 } AlaEServiceUNIProfileEntry ::= SEQUENCE { alaEServiceUNIProfileID DisplayString, alaEServiceUNIProfileStpBpduTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfile8021xTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfile8021ABTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfile8023adTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileGvrpTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileAmapTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileRowStatus RowStatus, alaEServiceUNIProfileMvrpTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileTunnelMac MacAddress, alaEServiceUNIProfileLacpMarkerTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileOamTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoPagpTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoUdldTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoCdpTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoVtpTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoDtpTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoPvstTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoVlanTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileCiscoUplinkTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileIeeeMacTreatment INTEGER } alaEServiceUNIProfileID OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A label given to uniquely identify this profile. Must be at least one character long." ::= { alaEServiceUNIProfileEntry 1 } alaEServiceUNIProfileStpBpduTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the spanning tree protocol BPDU received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling." DEFVAL { tunnel } ::= { alaEServiceUNIProfileEntry 2 } alaEServiceUNIProfile8021xTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the IEEE 802.1x PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. From 6.6.1.680.R01 Post GA, this object became read-create." DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 3 } alaEServiceUNIProfile8021ABTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the IEEE 802.1AB PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. From 6.6.1.680.R01 Post GA, this object became read-create." DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 4 } alaEServiceUNIProfile8023adTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the IEEE 802.1ad PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. From 6.6.1.680.R01 Post GA, this object became read-create." DEFVAL { peer } ::= { alaEServiceUNIProfileEntry 5 } alaEServiceUNIProfileGvrpTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the GVRP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling." DEFVAL { tunnel } ::= { alaEServiceUNIProfileEntry 6 } alaEServiceUNIProfileAmapTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the Alcatel propietary AMAP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currenly mac-tunnel is not supported. From 6.6.1.680.R01 Post GA, this object became read-create." DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 7 } alaEServiceUNIProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry." ::= { alaEServiceUNIProfileEntry 8 } alaEServiceUNIProfileMvrpTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the MVRP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling." DEFVAL { tunnel } ::= { alaEServiceUNIProfileEntry 9 } alaEServiceUNIProfileTunnelMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the tunnel mac used to tunnel L2 protocol to NNI ports" ::= { alaEServiceUNIProfileEntry 10 } alaEServiceUNIProfileLacpMarkerTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the LACP MARKER PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling." DEFVAL { peer } ::= { alaEServiceUNIProfileEntry 11 } alaEServiceUNIProfileOamTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the OAM PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling." DEFVAL { peer } ::= { alaEServiceUNIProfileEntry 12 } alaEServiceUNIProfileCiscoPagpTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the PAGP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer is not supported" DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 13 } alaEServiceUNIProfileCiscoUdldTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the UDLD PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling." DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 14 } alaEServiceUNIProfileCiscoCdpTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the CDC PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer is not supported" DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 15 } alaEServiceUNIProfileCiscoVtpTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the VTP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer is not supported" DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 16 } alaEServiceUNIProfileCiscoDtpTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the DTP PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer not supported" DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 17 } alaEServiceUNIProfileCiscoPvstTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the PVST PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer not supported" DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 18 } alaEServiceUNIProfileCiscoVlanTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the VLAN PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunnelling. Currently peer not supported" DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 19 } alaEServiceUNIProfileCiscoUplinkTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the UPLINK PDU frames received on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel(4) enables mac-tunnelling. Currently peer not supported." DEFVAL { drop } ::= { alaEServiceUNIProfileEntry 20 } alaEServiceUNIProfileIeeeMacTreatment OBJECT-TYPE SYNTAX INTEGER { unknown(0), ieeeFwdAll(1), ieeeDropAll(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the IEEEE Mac treatment unknown (0) the type is not defined. ieee-fwd-all(1) - Forwards all IEEE MAC's ieee-drop-all(2) - Discards all IEEE MAC's." DEFVAL { ieeeFwdAll } ::= { alaEServiceUNIProfileEntry 21 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service Service Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the services and their assigned SVLAN for the E-Service feature." ::= { alaEService 4 } alaEServiceEntry OBJECT-TYPE SYNTAX AlaEServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The svlan/ipmvlan-port association." INDEX { IMPLIED alaEServiceID } ::= { alaEServiceTable 1 } AlaEServiceEntry ::= SEQUENCE { alaEServiceID DisplayString, alaEServiceSVLAN INTEGER, alaEServiceVlanType INTEGER, alaEServiceRowStatus RowStatus, alaEServiceStatGreenCount Counter64, alaEServiceStatYellowCount Counter64, alaEServiceStatRedCount Counter64, alaEServiceStatTotalCount Counter64 } alaEServiceID OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A label given to uniquely identify this Service. Must be at least one character long." ::= { alaEServiceEntry 1 } alaEServiceSVLAN OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "The SVLAN number of the SVLAN chosen to the be transport for this service." ::= { alaEServiceEntry 2 } alaEServiceVlanType OBJECT-TYPE SYNTAX INTEGER { unknown(0), svlan(1), ipmvlan(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the vlan this service is going to attach to. When creating the service, the type should match the vlanId specified in the request." ::= { alaEServiceEntry 3 } alaEServiceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a service. When creating or deleting the service, the user needs to provide both the svlan and the vlantype objects." ::= { alaEServiceEntry 4 } alaEServiceStatGreenCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the number of packets/bytes being Green compliant (i.e. in case of srTCM and trTCM, packet is CIR/CBS compliant)." ::= { alaEServiceEntry 5 } alaEServiceStatYellowCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the number of packets/bytes being Yellow compliant (i.e. in case of srTCM and trTCM, packet is PIR/PBS compliant)." ::= { alaEServiceEntry 6 } alaEServiceStatRedCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the number of packets/bytes being Red compliant (i.e. in case of srTCM and trTCM, packet is neither CIR/CBS nor PIR/PBS compliant)." ::= { alaEServiceEntry 7 } alaEServiceStatTotalCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the total number of packets/bytes (sum of Green, Yellow and Red counters)." ::= { alaEServiceEntry 8 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service SAP Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceSapTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceSapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the Service Access Points (Sap) listed by ID. This table is used to create, delete, and modify the SAP's profile" ::= { alaEService 5 } alaEServiceSapEntry OBJECT-TYPE SYNTAX AlaEServiceSapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of SAP." INDEX { alaEServiceSapID} ::= { alaEServiceSapTable 1 } AlaEServiceSapEntry ::= SEQUENCE { alaEServiceSapID Integer32, alaEServiceSapServiceID DisplayString, alaEServiceSapProfile DisplayString, alaEServiceSapRowStatus RowStatus } alaEServiceSapID OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Number given to uniquely identify the SAP." ::= { alaEServiceSapEntry 1 } alaEServiceSapServiceID OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "A label given to uniquely identify the Service this SAP is for. Must be at least one character long." ::= { alaEServiceSapEntry 2 } alaEServiceSapProfile OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The string identifying the SAP Profile this sap is to use. If specified, must match an existing SAP Profile." ::= { alaEServiceSapEntry 3 } alaEServiceSapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a sap. When creating the sap, the user needs to provide the service name in the same set request." ::= { alaEServiceSapEntry 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service SAP CVLAN Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceSapCvlanTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceSapCvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the Service Access Points (Sap) where the CVLANs are bound to their service." ::= { alaEService 6 } alaEServiceSapCvlanEntry OBJECT-TYPE SYNTAX AlaEServiceSapCvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CVLAN to Sap binding." INDEX { alaEServiceSapCvlanSapID, alaEServiceSapCvlanCvlan } ::= { alaEServiceSapCvlanTable 1 } AlaEServiceSapCvlanEntry ::= SEQUENCE { alaEServiceSapCvlanSapID Integer32, alaEServiceSapCvlanCvlan INTEGER, alaEServiceSapCvlanMapType INTEGER, alaEServiceSapCvlanRowStatus RowStatus } alaEServiceSapCvlanSapID OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Number given to uniquely identify this SAP." ::= { alaEServiceSapCvlanEntry 1 } alaEServiceSapCvlanCvlan OBJECT-TYPE SYNTAX INTEGER (0..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is the CVLAN ID that this binding is targeted at. The CVLAN ID may be 0, which indicates an all or untagged only mapping type." ::= { alaEServiceSapCvlanEntry 2 } alaEServiceSapCvlanMapType OBJECT-TYPE SYNTAX INTEGER { single (1), all(2), untaggedOnly (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object is the mapping type that defines what CVLANs are mapped into this service. Multiple mappings can be defined for CVLAN to service, however only one all (2) or untaggedOnly (3) mapping entry can be created per UNI. A mapping type of Single (1) denotes a specific CVLAN value to bind to the service. A mapping type of All (2) denotes that all customer frames that do not map to any other SAP, will be mapped into this service. A mapping type of Untagged (3) denotes that only the untagged frames will be mapped into this service." DEFVAL { single } ::= { alaEServiceSapCvlanEntry 3 } alaEServiceSapCvlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a SAP." ::= { alaEServiceSapCvlanEntry 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service Port Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServicePortTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServicePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the ports used by the EService feature. Both UNI and NNI are listed here." ::= { alaEService 7 } alaEServicePortEntry OBJECT-TYPE SYNTAX AlaEServicePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of ports being used by EService." INDEX { alaEServicePortID} ::= { alaEServicePortTable 1 } AlaEServicePortEntry ::= SEQUENCE { alaEServicePortID InterfaceIndex, alaEServicePortType INTEGER, alaEServicePortVendorTpid Integer32, alaEServicePortLegacyStpBpdu INTEGER, alaEServicePortLegacyGvrpPdu INTEGER, alaEServicePortUniProfile DisplayString, alaEServicePortTransBridging INTEGER, alaEServicePortLegacyMvrpPdu INTEGER } alaEServicePortID OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IfIndex of this UNI or NNI Port." ::= { alaEServicePortEntry 1 } alaEServicePortType OBJECT-TYPE SYNTAX INTEGER { uni (1), nni (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of port for Vlan Stacking operation. uni (1) represents a customer facing port on which traffic may enter the E-Service. nni (2) respresents a provider network port over which the E-Service may be connected." DEFVAL { uni } ::= { alaEServicePortEntry 2 } alaEServicePortVendorTpid OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "he TPID for this port if type is NNI. It is used for the incoming data traffic parsing and it is substituted to the 802.1Q standard Tpid for the outgoing data traffic. This is used for compatibility with other vendor equipment. The default value is the standard value 0x8100." DEFVAL { 33024 } ::= { alaEServicePortEntry 3 } alaEServicePortLegacyStpBpdu OBJECT-TYPE SYNTAX INTEGER { notApplicable (0), enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The legacy STP BPDU treatment for this port if NNI. It defines the type of processing applied to STP legacy BPDUs on network ports. Legacy BPDU refer to conventional/customer BPDUs with MAC address 01:80:c2:00:00:00 and its processing on network ports can be enabled/disabled by this object.By default the value is disabled i.e provider MAC BPDU with MAC address 01:80:c2:00:00:08 would be processed at network ports." DEFVAL { disable } ::= { alaEServicePortEntry 4 } alaEServicePortLegacyGvrpPdu OBJECT-TYPE SYNTAX INTEGER { notApplicable (0), enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The legacy GVRP PDU treatment for this port if NNI. It defines the type of processing applied to GVRP PDUs on network ports. " DEFVAL { disable } ::= { alaEServicePortEntry 5 } alaEServicePortUniProfile OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "The label of an existing UNI profile that which contains various properties to be applied to this port if UNI." ::= { alaEServicePortEntry 6 } alaEServicePortTransBridging OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Transparent Bridging status for the nni Port." DEFVAL { disable } ::= { alaEServicePortEntry 7 } alaEServicePortLegacyMvrpPdu OBJECT-TYPE SYNTAX INTEGER { notApplicable (0), enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The legacy MVRP PDU treatment for this port if NNI. It defines the type of processing applied to MVRP PDUs on network ports. " DEFVAL { disable } ::= { alaEServicePortEntry 8 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service SAP-UNI Binding Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceSapUniTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceSapUniEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the UNI that are bound to each SAP for classifying traffic into each EService. Not that writing to this table may create a new UNI." ::= { alaEService 8 } alaEServiceSapUniEntry OBJECT-TYPE SYNTAX AlaEServiceSapUniEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of SAP-UNI bindings being used by EService." INDEX { alaEServiceSapUniSap, alaEServiceSapUniUni, alaEServiceSapUniCvlan } ::= { alaEServiceSapUniTable 1 } AlaEServiceSapUniEntry ::= SEQUENCE { alaEServiceSapUniSap Integer32, alaEServiceSapUniUni InterfaceIndex, alaEServiceSapUniRowStatus RowStatus, alaEServiceSapUniCvlan InterfaceIndex } alaEServiceSapUniSap OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SAP ID that is configured onto this port." ::= { alaEServiceSapUniEntry 1 } alaEServiceSapUniUni OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IfIndex of this UNI Port." ::= { alaEServiceSapUniEntry 2 } alaEServiceSapUniRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a binding" ::= { alaEServiceSapUniEntry 3 } alaEServiceSapUniCvlan OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Cvlan to be inserted for untagged frames incoming in this UNI Port if Cvlan insertion feature enabled else 0" ::= { alaEServiceSapUniEntry 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service NNI-SVLAN Binding Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceNniSvlanTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceNniSvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the SVLANs bound to each NNI for use by the EService feature." ::= { alaEService 9 } alaEServiceNniSvlanEntry OBJECT-TYPE SYNTAX AlaEServiceNniSvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of NNI-SVLAN bindings being used by EService." INDEX { alaEServiceNniSvlanNni, alaEServiceNniSvlanSvlan} ::= { alaEServiceNniSvlanTable 1 } AlaEServiceNniSvlanEntry ::= SEQUENCE { alaEServiceNniSvlanNni InterfaceIndex, alaEServiceNniSvlanSvlan INTEGER, alaEServiceNniSvlanRowStatus RowStatus, alaEServiceNniSvlanVpaType INTEGER } alaEServiceNniSvlanNni OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IfIndex of this NNI Port." ::= { alaEServiceNniSvlanEntry 1 } alaEServiceNniSvlanSvlan OBJECT-TYPE SYNTAX INTEGER (2..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SVLAN bound to this port. SVLAN cannot be 1." ::= { alaEServiceNniSvlanEntry 2 } alaEServiceNniSvlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry. The supported value for set are createAndGo (4) and destroy(6), to add or remove a binding" ::= { alaEServiceNniSvlanEntry 3 } -- alaEServiceNniSvlanVpaType is added in 6.3.4.R01 alaEServiceNniSvlanVpaType OBJECT-TYPE SYNTAX INTEGER { stp (1), erp (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to specify whether the VPA state is to be controlled by an ERP or a STP. By default VPA state is controlled by STP." DEFVAL { stp } ::= { alaEServiceNniSvlanEntry 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service srTCM and trTCM Counter Statistics Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceSapCvlanPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceSapCvlanPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A statistics table that contains the counters per SAP." ::= { alaEService 10 } alaEServiceSapCvlanPortStatEntry OBJECT-TYPE SYNTAX AlaEServiceSapCvlanPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A E-Service Statistics Entry." INDEX { alaEServiceSapCvlanPortStatSapID, alaEServiceSapCvlanPortStatCvlanID, alaEServiceSapCvlanPortStatPortID } ::= { alaEServiceSapCvlanPortStatTable 1 } AlaEServiceSapCvlanPortStatEntry ::= SEQUENCE { alaEServiceSapCvlanPortStatSapID Integer32, alaEServiceSapCvlanPortStatCvlanID INTEGER, alaEServiceSapCvlanPortStatPortID InterfaceIndex, alaEServiceSapCvlanPortStatGreenCount Counter64, alaEServiceSapCvlanPortStatYellowCount Counter64, alaEServiceSapCvlanPortStatRedCount Counter64, alaEServiceSapCvlanPortStatTotalCount Counter64 } alaEServiceSapCvlanPortStatSapID OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Number given to uniquely identify the SAP." ::= { alaEServiceSapCvlanPortStatEntry 1 } alaEServiceSapCvlanPortStatCvlanID OBJECT-TYPE SYNTAX INTEGER (0..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is the CVLAN ID that this binding is targeted at. The CVLAN ID may be 0, which indicates an all or untagged only mapping type." ::= { alaEServiceSapCvlanPortStatEntry 2 } alaEServiceSapCvlanPortStatPortID OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IfIndex of this UNI Port." ::= { alaEServiceSapCvlanPortStatEntry 3 } alaEServiceSapCvlanPortStatGreenCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the number of packets/bytes being Green compliant (i.e. in case of srTCM and trTCM, packet is CIR/CBS compliant) per UNI port, per CVLAN. This object is applicable only when ingress bandwidth is not shared across SAP ports and CVLANs." ::= { alaEServiceSapCvlanPortStatEntry 4 } alaEServiceSapCvlanPortStatYellowCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the number of packets/bytes being Yellow compliant (i.e. in case of srTCM and trTCM, packet is PIR/PBS compliant) per UNI port, per CVLAN. This object is applicable only when ingress bandwidth is not shared across SAP ports and CVLANs." ::= { alaEServiceSapCvlanPortStatEntry 5 } alaEServiceSapCvlanPortStatRedCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the number of packets/bytes being Red compliant (i.e. in case of srTCM and trTCM, packet is neither CIR/CBS nor PIR/PBS compliant) per UNI port, per CVLAN. This object is applicable only when ingress bandwidth is not shared across SAP ports and CVLANs." ::= { alaEServiceSapCvlanPortStatEntry 6 } alaEServiceSapCvlanPortStatTotalCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for the total number of packets/bytes (sum of Green, Yellow and Red counters) per UNI port, per CVLAN. This object is applicable only when ingress bandwidth is not shared across SAP ports and CVLANs." ::= { alaEServiceSapCvlanPortStatEntry 7 } -- Added in 6.6.3.R01 *** Begin -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Profile L2 Custom protocol association entries Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIProfileL2CustomProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceUNIProfileL2CustomProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains l2 custom protocol entries with name and action associated to a uni profile. An entry in this table is created when an l2 custom protocol entry is associated to uni profile." ::= {alaEService 11} alaEServiceUNIProfileL2CustomProtocolEntry OBJECT-TYPE SYNTAX AlaEServiceUNIProfileL2CustomProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service Service Profile entry associated with l2 custom protocol entry." INDEX {alaEServiceL2CustomProtocolUNIProfileID, alaEServiceUNIProfileL2CustomProtocolID} ::= {alaEServiceUNIProfileL2CustomProtocolTable 1} AlaEServiceUNIProfileL2CustomProtocolEntry ::= SEQUENCE { alaEServiceL2CustomProtocolUNIProfileID SnmpAdminString, alaEServiceUNIProfileL2CustomProtocolID SnmpAdminString, alaEServiceUNIProfileL2CustomProtocolTreatment AlaEServiceUNIProfileProtocolTreatment, alaEServiceUNIProfileL2CustomProtocolRowStatus RowStatus } alaEServiceL2CustomProtocolUNIProfileID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A label given to uniquely identify this profile. Must be at least one character long." ::= {alaEServiceUNIProfileL2CustomProtocolEntry 1} alaEServiceUNIProfileL2CustomProtocolID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the L2 Custom protocol entry associated to UNI profile. Must be at least one character long." ::= { alaEServiceUNIProfileL2CustomProtocolEntry 2 } alaEServiceUNIProfileL2CustomProtocolTreatment OBJECT-TYPE SYNTAX AlaEServiceUNIProfileProtocolTreatment MAX-ACCESS read-create STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the destination Mac address matching with the L2 Custom protocol entry mac address on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunneling." DEFVAL {tunnel} ::= { alaEServiceUNIProfileL2CustomProtocolEntry 3 } alaEServiceUNIProfileL2CustomProtocolRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry." ::= { alaEServiceUNIProfileL2CustomProtocolEntry 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service L2 Custom protocol entries Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceL2CustomProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceL2CustomProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains l2 custom protocol entries with name, Mac address, mask, ether type and ether sub type." ::= { alaEService 12 } alaEServiceL2CustomProtocolEntry OBJECT-TYPE SYNTAX AlaEServiceL2CustomProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service Service with l2 custom protocol entry." INDEX {alaEServiceL2CustomProtocolID } ::= { alaEServiceL2CustomProtocolTable 1 } AlaEServiceL2CustomProtocolEntry ::= SEQUENCE { alaEServiceL2CustomProtocolID SnmpAdminString, alaEServiceL2CustomProtocolEntryType AlaEServiceL2CustomProtocolType, alaEServiceL2CustomProtocolMac MacAddress, alaEServiceL2CustomProtocolMask MacAddress, alaEServiceL2CustomProtocolEtherType INTEGER, alaEServiceL2CustomProtocolEtherSubType INTEGER, alaEServiceL2CustomProtocolSsap INTEGER, alaEServiceL2CustomProtocolDsap INTEGER, alaEServiceL2CustomProtocolPid INTEGER, alaEServiceL2CustomProtocolRowStatus RowStatus } alaEServiceL2CustomProtocolID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the L2 Custom protocol entry which is an identifier to this table. Must be at least one character long." ::= { alaEServiceL2CustomProtocolEntry 1 } alaEServiceL2CustomProtocolEntryType OBJECT-TYPE SYNTAX AlaEServiceL2CustomProtocolType MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the custom L2 protocol entry type" DEFVAL {macType} ::= { alaEServiceL2CustomProtocolEntry 2 } alaEServiceL2CustomProtocolMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the destination mac address that needs L2 protocol handling" ::= { alaEServiceL2CustomProtocolEntry 3 } alaEServiceL2CustomProtocolMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the range of destination mac address that that needs L2 protocol handling" ::= { alaEServiceL2CustomProtocolEntry 4 } alaEServiceL2CustomProtocolEtherType OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Ether type value for generic ethertype." ::= { alaEServiceL2CustomProtocolEntry 5 } alaEServiceL2CustomProtocolEtherSubType OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "if Ether type >1536 then the sub type is allowed to be configured" ::= { alaEServiceL2CustomProtocolEntry 6 } alaEServiceL2CustomProtocolSsap OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "SSAP value for generic SSAP and SNAP rules, when Ether type < 1536" ::= { alaEServiceL2CustomProtocolEntry 7 } alaEServiceL2CustomProtocolDsap OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "DSAP value for generic DSAP and SNAP rules, when Ether type < 1536" ::= { alaEServiceL2CustomProtocolEntry 8 } alaEServiceL2CustomProtocolPid OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "protocol identifier in case of LLC SNAP packet" ::= { alaEServiceL2CustomProtocolEntry 9 } alaEServiceL2CustomProtocolRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this table entry." ::= { alaEServiceL2CustomProtocolEntry 10} -- Added in 6.6.3.R01 *** End -- Added in 6.6.3.R01 *** Statistics Begin -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Port L2 Statistics entries Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIPortL2ProtocolStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceUNIPortL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table, that contains UNI port L2 protocol frame statistics." ::= {alaEService 13} alaEServiceUNIPortL2ProtocolStatisticsEntry OBJECT-TYPE SYNTAX AlaEServiceUNIPortL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service Service UNI port L2 protocol statistics entry associated with an L2 protocol and a port entry." INDEX {alaEServiceUNIPortID, IMPLIED alaEServiceUNIPortL2ProtocolID} ::= {alaEServiceUNIPortL2ProtocolStatisticsTable 1} AlaEServiceUNIPortL2ProtocolStatisticsEntry ::= SEQUENCE { alaEServiceUNIPortID InterfaceIndex, alaEServiceUNIPortL2ProtocolID SnmpAdminString, alaEServiceUNIPortL2RxFrames Counter32, alaEServiceUNIPortL2TunneledFrames Counter32, alaEServiceUNIPortL2DroppedFrames Counter32, alaEServiceUNIPortL2PeeredFrames Counter32, alaEServiceUNIPortL2MACTunneledFrames Counter32, alaEServiceUNIPortL2MACDeTunneledFrames Counter32, alaEServiceUNIPortL2LastSourceMAC MacAddress } alaEServiceUNIPortID OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index of the UNI." ::= {alaEServiceUNIPortL2ProtocolStatisticsEntry 1} alaEServiceUNIPortL2ProtocolID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the L2 protocol entry. Must be at least one character long." ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 2 } alaEServiceUNIPortL2RxFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames of this protocol received on this port and trapped to CPU." ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 3 } alaEServiceUNIPortL2TunneledFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames of this protocol received on this port trapped to CPU and tunneled." ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 4 } alaEServiceUNIPortL2DroppedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames of this protocol received on this port trapped to CPU and dropped." ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 5 } alaEServiceUNIPortL2PeeredFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames of this protocol received on this port trapped to CPU and peered." ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 6 } alaEServiceUNIPortL2MACTunneledFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames of this protocol received on this port trapped to CPU and MAC tunneled." ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 7 } alaEServiceUNIPortL2MACDeTunneledFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames of this protocol received on this port trapped to CPU and MAC de-tunneled." ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 8 } alaEServiceUNIPortL2LastSourceMAC OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the source MAC address of last frame of this protocol on this port trapped to CPU" ::= { alaEServiceUNIPortL2ProtocolStatisticsEntry 9 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service NNI Port L2 Statistics entries Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceNNIPortL2ProtocolStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceNNIPortL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table, that contains NNI port L2 protocol frame statistics." ::= {alaEService 14} alaEServiceNNIPortL2ProtocolStatisticsEntry OBJECT-TYPE SYNTAX AlaEServiceNNIPortL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service NNI port L2 protocol statistics entry associated with port." INDEX {alaEServiceNNIPortID} ::= {alaEServiceNNIPortL2ProtocolStatisticsTable 1} AlaEServiceNNIPortL2ProtocolStatisticsEntry ::= SEQUENCE { alaEServiceNNIPortID InterfaceIndex, alaEServiceNNIPortL2RxMACTunneledFrames Counter32, alaEServiceNNIPortL2MACTunneledDiscardFrames Counter32, alaEServiceNNIPortL2ClearStats INTEGER } alaEServiceNNIPortID OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index of the NNI." ::= {alaEServiceNNIPortL2ProtocolStatisticsEntry 1} alaEServiceNNIPortL2RxMACTunneledFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames trapped to CPU with tunnel MAC." ::= { alaEServiceNNIPortL2ProtocolStatisticsEntry 2 } alaEServiceNNIPortL2MACTunneledDiscardFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of discarded frames that are trapped to CPU with tunnel MAC." ::= { alaEServiceNNIPortL2ProtocolStatisticsEntry 3 } alaEServiceNNIPortL2ClearStats OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used to clear the NNI port statistics of the interface." DEFVAL { default } ::= { alaEServiceNNIPortL2ProtocolStatisticsEntry 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Profile L2 Total RX Statistics entries Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIProfileL2ProtocolTotalStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceUNIProfileL2ProtocolTotalStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table, that contains UNI profile L2 protocol frame total RX statistics of all ports of the profile" ::= {alaEService 15} alaEServiceUNIProfileL2ProtocolTotalStatisticsEntry OBJECT-TYPE SYNTAX AlaEServiceUNIProfileL2ProtocolTotalStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service UNI profile L2 protocol total RX statistics entry associated with all ports of the UNI profile." INDEX {IMPLIED alaEServiceUNIProfile} ::= {alaEServiceUNIProfileL2ProtocolTotalStatisticsTable 1} AlaEServiceUNIProfileL2ProtocolTotalStatisticsEntry ::= SEQUENCE { alaEServiceUNIProfile SnmpAdminString, alaEServiceUNIProfileL2ProtocolTotalRxFrames Counter32, alaEServiceUNIProfileL2ProtocolClearStats INTEGER } alaEServiceUNIProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A label given to uniquely identify this profile. Must be at least one character long." ::= { alaEServiceUNIProfileL2ProtocolTotalStatisticsEntry 1} alaEServiceUNIProfileL2ProtocolTotalRxFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames L2 protocol frames received by all the ports of bind to this profile." ::= { alaEServiceUNIProfileL2ProtocolTotalStatisticsEntry 2 } alaEServiceUNIProfileL2ProtocolClearStats OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to clear the UNI profile statistics of the interface." DEFVAL { default } ::= { alaEServiceUNIProfileL2ProtocolTotalStatisticsEntry 3 } -- The E-Service UNI Profile L2 Well Known protocl RX Statistics entries Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIProfileIEEEL2ProtocolStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table, that contains UNI profile L2 well known protocol frame RX statistics of all ports of the profile" ::= {alaEService 16} alaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry OBJECT-TYPE SYNTAX AlaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service UNI profile L2 well known protocol RX statistics entry associated with all ports of the UNI profile." INDEX {alaEServiceUNIProfileIEEEL2ProfileID, alaEServiceUNIProfileIEEEL2ProtocolIndex} ::= {alaEServiceUNIProfileIEEEL2ProtocolStatisticsTable 1} AlaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry ::= SEQUENCE { alaEServiceUNIProfileIEEEL2ProfileID SnmpAdminString, alaEServiceUNIProfileIEEEL2ProtocolIndex INTEGER, alaEServiceUNIProfileIEEEL2ProtocolRxFrames Counter32, alaEServiceUNIProfileIEEEL2ProtocolTreatment INTEGER } alaEServiceUNIProfileIEEEL2ProfileID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A label given to uniquely identify this profile. Must be at least one character long." ::= { alaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry 1} alaEServiceUNIProfileIEEEL2ProtocolIndex OBJECT-TYPE SYNTAX INTEGER { lacpLacpmarkerOam (1), ieee802dot1x (2), lldp (3), amap (4), cisco (5), stp (6), gvrpMvrp (7) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the well known protocol group this row corresponds to." ::= {alaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry 2 } alaEServiceUNIProfileIEEEL2ProtocolRxFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the number of frames this L2 well known protocol frames received by all the ports of bind to this profile." ::= { alaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry 3 } alaEServiceUNIProfileIEEEL2ProtocolTreatment OBJECT-TYPE SYNTAX INTEGER { invalid (0), fwd (1), drop (2), cpu (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the destination Mac address matching with the L2 Custom protocol entry mac address on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunneling." ::= { alaEServiceUNIProfileIEEEL2ProtocolStatisticsEntry 4 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Profile L2 RX Statistics entries Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIProfileCustomL2ProtocolStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceUNIProfileCustomL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table, that contains UNI profile L2 protocol frame RX statistics of all ports of the profile. Each entry represents statistics collected for one protocol of the UNI profile." ::= {alaEService 17} alaEServiceUNIProfileCustomL2ProtocolStatisticsEntry OBJECT-TYPE SYNTAX AlaEServiceUNIProfileCustomL2ProtocolStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service UNI profile L2 protocol RX statistics entry associated with all ports of the UNI profile." INDEX {alaEServiceUNIProfileCustomL2StatsProfileID, alaEServiceUNIProfileCustomL2ProtocolIndex} ::= {alaEServiceUNIProfileCustomL2ProtocolStatisticsTable 1} AlaEServiceUNIProfileCustomL2ProtocolStatisticsEntry ::= SEQUENCE { alaEServiceUNIProfileCustomL2StatsProfileID SnmpAdminString, alaEServiceUNIProfileCustomL2ProtocolIndex SnmpAdminString, alaEServiceUNIProfileCustomL2ProtocolRxFrames Counter32, alaEServiceUNIProfileCustomL2ProtocolTreatment INTEGER } alaEServiceUNIProfileCustomL2StatsProfileID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A label given to uniquely identify this profile. Must be at least one character long." ::= { alaEServiceUNIProfileCustomL2ProtocolStatisticsEntry 1} alaEServiceUNIProfileCustomL2ProtocolIndex OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the L2 protocol entry. Must be at least one character long." ::= { alaEServiceUNIProfileCustomL2ProtocolStatisticsEntry 2 } alaEServiceUNIProfileCustomL2ProtocolRxFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the total number of frames of this protocol received on this port and trapped to CPU." ::= { alaEServiceUNIProfileCustomL2ProtocolStatisticsEntry 3 } alaEServiceUNIProfileCustomL2ProtocolTreatment OBJECT-TYPE SYNTAX INTEGER { invalid (0), fwd (1), drop (2), cpu (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the behavior of the bridge in regards to the destination Mac address matching with the L2 Custom protocol entry mac address on the UNI. Tunnel (1) enables the PDU to be tunneled across the provider network. Discard (2) causes the PDU of the protocol to be discarded and not enter the provider network. Peer (3) means that on this port the bridge is to participate in the protocol. Mac-Tunnel (4) enables mac-tunneling." ::= { alaEServiceUNIProfileCustomL2ProtocolStatisticsEntry 4 } alaEServiceL2PTProtocolStatisticsClear OBJECT IDENTIFIER ::= { alaEService 18 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Port L2 Statistics Global Clear -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIPortL2GlobalClearStatistics OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the global clear control for L2 protocol statistics of all UNI ports The value reset (1) indicates clear UNI port statistics of all ports in the system. By default, this object contains a zero value." DEFVAL { default } ::= { alaEServiceL2PTProtocolStatisticsClear 1 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service NNI Port L2 Statistics Global Clear -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceNNIPortL2GlobalClearStatistics OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the global clear control for L2 protocol statistics of all NNI ports The value reset (1) indicates clear NNI port statistics of all ports in the system. By default, this object contains a zero value." DEFVAL { default } ::= { alaEServiceL2PTProtocolStatisticsClear 2 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Profile L2 Statistics Global Clear -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIProfileL2GlobalClearStatistics OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the global clear control for L2 protocol statistics of all UNI profiles The value reset (1) indicates clear UNI profile statistics of all ports in the system. By default, this object contains a zero value." DEFVAL { default } ::= { alaEServiceL2PTProtocolStatisticsClear 3 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- The E-Service UNI Port L2 Statistics Clear Table -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceUNIPortL2ProtocolStatisticsClearTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceUNIPortL2ProtocolStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table, to clear UNI port L2 protocol frame statistics." ::= {alaEService 19} alaEServiceUNIPortL2ProtocolStatisticsClearEntry OBJECT-TYPE SYNTAX AlaEServiceUNIPortL2ProtocolStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-Service Service UNI port L2 protocol statistics clear entry associated with port." INDEX {alaEServiceUNIPortClearID} ::= {alaEServiceUNIPortL2ProtocolStatisticsClearTable 1} AlaEServiceUNIPortL2ProtocolStatisticsClearEntry ::= SEQUENCE { alaEServiceUNIPortClearID InterfaceIndex, alaEServiceUNIPortL2ClearStats INTEGER } alaEServiceUNIPortClearID OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index of the UNI." ::= {alaEServiceUNIPortL2ProtocolStatisticsClearEntry 1} alaEServiceUNIPortL2ClearStats OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to clear the UNI port statistics of the interface." DEFVAL { default } ::= { alaEServiceUNIPortL2ProtocolStatisticsClearEntry 2 } alaEServiceNNIPortL2ProtocolStatisticsClearTable OBJECT-TYPE SYNTAX SEQUENCE OF AlaEServiceNNIPortL2ProtocolStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table, to clear NNI port L2 protocol frame statistics." ::= {alaEService 20} alaEServiceNNIPortL2ProtocolStatisticsClearEntry OBJECT-TYPE SYNTAX AlaEServiceNNIPortL2ProtocolStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An E-serive to clear NNI port L2 protocol frame statistics." INDEX {alaEServiceNNIPortClearID} ::= { alaEServiceNNIPortL2ProtocolStatisticsClearTable 1 } AlaEServiceNNIPortL2ProtocolStatisticsClearEntry ::= SEQUENCE { alaEServiceNNIPortClearID InterfaceIndex, alaEServiceNNIPortL2ClearStatistics INTEGER } alaEServiceNNIPortClearID OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index of the NNI." ::= {alaEServiceNNIPortL2ProtocolStatisticsClearEntry 1} alaEServiceNNIPortL2ClearStatistics OBJECT-TYPE SYNTAX INTEGER { default(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to clear the NNI port statistics of the interface." DEFVAL { default } ::= { alaEServiceNNIPortL2ProtocolStatisticsClearEntry 2 } -- Added in 6.6.3.R01 *** Statistics End -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- COMPLIANCE -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alcatelIND1EServiceMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for E-Service." MODULE MANDATORY-GROUPS { alaEServiceSapProfileGroup, alaEServiceUNIProfileGroup, alaEServiceGroup, alaEServiceSapGroup, alaEServiceSapUniGroup, alaEServiceSapCvlanGroup, alaEServicePortGroup, alaEServiceNniSvlanGroup, alaEServiceSapCvlanPortStatGroup, alaEServiceInfoGroup } ::= { alcatelIND1EServiceMIBCompliances 1 } -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -- UNITS OF CONFORMANCE -- xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alaEServiceSapProfileGroup OBJECT-GROUP OBJECTS { alaEServiceSapProfileCVLANTreatment, alaEServiceSapProfileReplacementCVLAN, alaEServiceSapProfilePriorityMapMode, alaEServiceSapProfileFixedPriority, alaEServiceSapProfileIngressBW, alaEServiceSapProfileBandwidthShare, alaEServiceSapProfileRowStatus, alaEServiceSapProfileEgressBW, alaEServiceSapProfileCIR, alaEServiceSapProfileCBS, alaEServiceSapProfilePIR, alaEServiceSapProfilePBS, alaEServiceSapProfileDepth } STATUS current DESCRIPTION "Collection of objects for management of E-Service Sap Profiles." ::= { alcatelIND1EServiceMIBGroups 1 } alaEServiceUNIProfileGroup OBJECT-GROUP OBJECTS { alaEServiceUNIProfileStpBpduTreatment, alaEServiceUNIProfile8021xTreatment, alaEServiceUNIProfile8021ABTreatment, alaEServiceUNIProfile8023adTreatment, alaEServiceUNIProfileGvrpTreatment, alaEServiceUNIProfileAmapTreatment, alaEServiceUNIProfileRowStatus, alaEServiceUNIProfileMvrpTreatment, alaEServiceUNIProfileTunnelMac, alaEServiceUNIProfileLacpMarkerTreatment, alaEServiceUNIProfileOamTreatment, alaEServiceUNIProfileCiscoPagpTreatment, alaEServiceUNIProfileCiscoUdldTreatment, alaEServiceUNIProfileCiscoCdpTreatment, alaEServiceUNIProfileCiscoVtpTreatment, alaEServiceUNIProfileCiscoDtpTreatment, alaEServiceUNIProfileCiscoPvstTreatment, alaEServiceUNIProfileCiscoVlanTreatment, alaEServiceUNIProfileCiscoUplinkTreatment, alaEServiceUNIProfileIeeeMacTreatment } STATUS current DESCRIPTION "Collection of objects for management of EService UNI Profiles." ::= { alcatelIND1EServiceMIBGroups 2 } alaEServiceGroup OBJECT-GROUP OBJECTS { alaEServiceSVLAN, alaEServiceVlanType, alaEServiceRowStatus, alaEServiceStatGreenCount, alaEServiceStatYellowCount, alaEServiceStatRedCount, alaEServiceStatTotalCount } STATUS current DESCRIPTION "Collection of objects for management of E-Services." ::= { alcatelIND1EServiceMIBGroups 3 } alaEServiceSapGroup OBJECT-GROUP OBJECTS { alaEServiceSapServiceID, alaEServiceSapProfile, alaEServiceSapRowStatus } STATUS current DESCRIPTION "Collection of objects for management of E-Service SAPs." ::= { alcatelIND1EServiceMIBGroups 4 } alaEServiceSapCvlanGroup OBJECT-GROUP OBJECTS { alaEServiceSapCvlanMapType, alaEServiceSapCvlanRowStatus } STATUS current DESCRIPTION "Collection of objects for management of E-Service SAP CVLAN bindings." ::= { alcatelIND1EServiceMIBGroups 5 } alaEServicePortGroup OBJECT-GROUP OBJECTS { alaEServicePortType, alaEServicePortVendorTpid, alaEServicePortLegacyStpBpdu, alaEServicePortLegacyGvrpPdu, alaEServicePortUniProfile, alaEServicePortTransBridging, alaEServicePortLegacyMvrpPdu } STATUS current DESCRIPTION "Collection of objects for management of E-Service Ports." ::= { alcatelIND1EServiceMIBGroups 6 } alaEServiceSapUniGroup OBJECT-GROUP OBJECTS { alaEServiceSapUniRowStatus } STATUS current DESCRIPTION "Collection of objects for management of E-Service SAP to UNI Binding." ::= { alcatelIND1EServiceMIBGroups 7 } alaEServiceNniSvlanGroup OBJECT-GROUP OBJECTS { alaEServiceNniSvlanRowStatus, alaEServiceNniSvlanVpaType } STATUS current DESCRIPTION "Collection of objects for management of E-Service SVLAN to NNI Binding." ::= { alcatelIND1EServiceMIBGroups 8 } alaEServiceSapCvlanPortStatGroup OBJECT-GROUP OBJECTS { alaEServiceSapCvlanPortStatGreenCount, alaEServiceSapCvlanPortStatYellowCount, alaEServiceSapCvlanPortStatRedCount, alaEServiceSapCvlanPortStatTotalCount } STATUS current DESCRIPTION "Collection of objects for srTCM and trTCM Counters." ::= { alcatelIND1EServiceMIBGroups 9 } alaEServiceInfoGroup OBJECT-GROUP OBJECTS { alaEServiceMode, alaEServiceStatReset, alaEServiceL2MacTunnel, alaEServiceUntaggedMode } STATUS current DESCRIPTION "Collection of E-Service Global Objects." ::= { alcatelIND1EServiceMIBGroups 10 } -- Added in 6.6.3.R01 *** Begin alaEServiceUNIProfileL2CustomProtocolGroup OBJECT-GROUP OBJECTS { alaEServiceUNIProfileL2CustomProtocolTreatment, alaEServiceUNIProfileL2CustomProtocolRowStatus } STATUS current DESCRIPTION "Collection of objects for management of E-Service UNI Profile to L2 Custom Protocol bindings." ::= { alcatelIND1EServiceMIBGroups 11 } alaEServiceL2CustomProtocolGroup OBJECT-GROUP OBJECTS { alaEServiceL2CustomProtocolEntryType, alaEServiceL2CustomProtocolMac, alaEServiceL2CustomProtocolMask, alaEServiceL2CustomProtocolEtherType, alaEServiceL2CustomProtocolEtherSubType, alaEServiceL2CustomProtocolSsap, alaEServiceL2CustomProtocolDsap, alaEServiceL2CustomProtocolPid, alaEServiceL2CustomProtocolRowStatus } STATUS current DESCRIPTION "Collection of objects for management of E-Service L2 Custom Protocol Group." ::= { alcatelIND1EServiceMIBGroups 12} -- Added in 6.6.3.R01 *** End -- Added in 6.6.3.R01 *** Begin Statistics alaEServiceUNIPortL2StatisticsGroup OBJECT-GROUP OBJECTS { alaEServiceUNIPortL2RxFrames, alaEServiceUNIPortL2TunneledFrames, alaEServiceUNIPortL2DroppedFrames, alaEServiceUNIPortL2PeeredFrames, alaEServiceUNIPortL2MACTunneledFrames, alaEServiceUNIPortL2MACDeTunneledFrames, alaEServiceUNIPortL2LastSourceMAC } STATUS current DESCRIPTION "Collection of objects for UNI port statistics management of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 13} alaEServiceNNIPortL2StatisticsGroup OBJECT-GROUP OBJECTS { alaEServiceNNIPortL2RxMACTunneledFrames, alaEServiceNNIPortL2MACTunneledDiscardFrames } STATUS current DESCRIPTION "Collection of objects for NNI port statistics management of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 14} alaEServiceUNIProfileL2ProtocolTotalStatisticsGroup OBJECT-GROUP OBJECTS { alaEServiceUNIProfileL2ProtocolTotalRxFrames, alaEServiceUNIProfileL2ProtocolClearStats } STATUS current DESCRIPTION "Collection of objects for UNI profile statistics management of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 15} alaEServiceUNIProfileIEEEL2ProtocolStatisticsGroup OBJECT-GROUP OBJECTS { alaEServiceUNIProfileIEEEL2ProtocolRxFrames, alaEServiceUNIProfileIEEEL2ProtocolTreatment } STATUS current DESCRIPTION "Collection of objects for UNI profile statistics for well known protocols of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 16} alaEServiceUNIProfileL2ProtocolStatisticsGroup OBJECT-GROUP OBJECTS { alaEServiceUNIProfileCustomL2ProtocolRxFrames, alaEServiceUNIProfileCustomL2ProtocolTreatment } STATUS current DESCRIPTION "Collection of objects for UNI profile statistics management of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 17} alaEServiceL2PTProtocolStatisticsClearGroup OBJECT-GROUP OBJECTS { alaEServiceUNIPortL2GlobalClearStatistics, alaEServiceNNIPortL2GlobalClearStatistics, alaEServiceUNIProfileL2GlobalClearStatistics } STATUS current DESCRIPTION "Collection of objects for UNI profile statistics management of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 18} alaEServiceUNIPortL2StatisticsClearGroup OBJECT-GROUP OBJECTS { alaEServiceUNIPortL2ClearStats } STATUS current DESCRIPTION "Collection of objects for UNI port statistics management of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 19} alaEServiceNNIPortL2StatisticsClearGroup OBJECT-GROUP OBJECTS { alaEServiceNNIPortL2ClearStatistics } STATUS current DESCRIPTION "Collection of objects for NNI port statistics management of E-Service L2 Tunneling Protocol Group." ::= { alcatelIND1EServiceMIBGroups 20} -- Added in 6.6.3.R01 *** End Statistics END