--**MOD+*********************************************************************** --* Module: ARUBAWIRED-LOOPPROTECT-MIB.mib --* --* (c) Copyright 2017,2022-2023 Hewlett Packard Enterprise Development LP --* All Rights Reserved. --* --* The contents of this software are proprietary and confidential --* to the Hewlett-Packard Development Company, L.P. No part of this --* program may be photocopied, reproduced, or translated into another --* programming language without prior written consent of the --* Hewlett-Packard Development Company, L.P. --* --* Purpose: This file contains MIB definition of ARUBAWIRED-LOOPPROTECT-MIB --* --**MOD-*********************************************************************** ARUBAWIRED-LOOPPROTECT-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, Integer32, Counter32 FROM SNMPv2-SMI TruthValue, TimeStamp, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF wndFeatures FROM ARUBAWIRED-NETWORKING-OID InterfaceIndex, ifIndex FROM IF-MIB; arubaWiredLoopProtectMIB MODULE-IDENTITY LAST-UPDATED "201711020000Z" -- November 02, 2017 ORGANIZATION "HPE/Aruba Networking Division" CONTACT-INFO "Hewlett-Packard Company 8000 Foothills Blvd. Roseville, CA 95747" DESCRIPTION "This MIB module contains HP proprietary extensions to the standard Loop Protect MIBs." REVISION "201711020000Z" -- November 02, 2017 DESCRIPTION "Initial revision." ::= { wndFeatures 1 } ConfigStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Used to indicate the configuration status for a group of objects. 'active' means that the values of the related objects are currently in use by the device. 'notInService' indicates that the objects have been reconfigured in such a way that the values cannot take effect until after the next reboot of the device. 'notReady' indicates that the objects are not consistent with each other." SYNTAX INTEGER { active(1), notInService(2), notReady(3) } VidList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight VlanIIndex (VID), with the first octet specifying VIDs 1 through 8, the second octet specifying VIDs 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered VID, and the least significant bit represents the highest numbered VID. Thus, each VID is represented by a single bit within the value of this object. If that bit has a value of 1 then that VID is included in the set of VIDs; the VID is not included if its bit has a value of 0. This list represents the entire range of VlanIndex values defined in the scope of IEEE 802.1Q." SYNTAX OCTET STRING (SIZE (0..512)) arubaWiredLoopProtectObjects OBJECT IDENTIFIER ::= { arubaWiredLoopProtectMIB 1 } -- ********************************************************************** -- Loop Protection Objects -- ********************************************************************** LoopProtectReceiverAction ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION " This TC describes the actions a port that receives a Loop Protection Protocol packet can take. The disableTx(1) enumeration indicates that the sender of the Loop Protect packet will be disabled. The noDisable(2) enumeration indicates that no port is to be disabled. The disableTxRx(3) enumeration indicates that the senders and receivers of the Loop Protect packets will be disabled." SYNTAX INTEGER { disableTx(1), noDisable(2), disableTxRx(3) } arubaWiredLoopProtect OBJECT IDENTIFIER ::= { arubaWiredLoopProtectObjects 5 } arubaWiredLoopProtectNotifications OBJECT IDENTIFIER ::= { arubaWiredLoopProtect 0 } arubaWiredLoopProtectBase OBJECT IDENTIFIER ::= { arubaWiredLoopProtect 1 } arubaWiredLoopProtectPort OBJECT IDENTIFIER ::= { arubaWiredLoopProtect 2 } arubaWiredLoopProtectInterval OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval in seconds at which Loop Protection packets are transmitted. The default value is 5 seconds." ::= { arubaWiredLoopProtectBase 1 } arubaWiredLoopProtectTrapLoopDetectEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether notifications should be sent when a loop is detected on a port. By default this object will have a value of false(2)." ::= { arubaWiredLoopProtectBase 2 } arubaWiredLoopProtectEnableTimer OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The time in seconds to wait before re-enabling a port disabled by Loop Protection. When a port is disabled by Loop Protection, a re-enable timer for the port is initialized. If the re-enable timer value is specified as zero seconds the port remains disabled, else the port is re-enabled after the specified time." ::= { arubaWiredLoopProtectBase 3 } arubaWiredLoopProtectMode OBJECT-TYPE SYNTAX INTEGER { port (1), vlan (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the operational mode of Loop Protection feature. The Loop Protection feature can be configured to operate in port mode or VLAN mode." DEFVAL { port } ::= { arubaWiredLoopProtectBase 4 } arubaWiredLoopProtectVIDList OBJECT-TYPE SYNTAX VidList MAX-ACCESS read-write STATUS current DESCRIPTION "A list of VLANs on which Loop Protection is enabled." ::= { arubaWiredLoopProtectBase 5 } arubaWiredLoopProtectPortTable OBJECT-TYPE SYNTAX SEQUENCE OF ArubaWiredLoopProtectPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Per-interface configuration for Loop Protection." ::= { arubaWiredLoopProtectPort 1 } arubaWiredLoopProtectPortEntry OBJECT-TYPE SYNTAX ArubaWiredLoopProtectPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Loop Protection configuration information for a single port." INDEX { arubaWiredLoopProtectPortInterfaceIndex } ::= { arubaWiredLoopProtectPortTable 1 } ArubaWiredLoopProtectPortEntry ::= SEQUENCE { arubaWiredLoopProtectPortInterfaceIndex InterfaceIndex, arubaWiredLoopProtectPortEnable TruthValue, arubaWiredLoopProtectPortLoopDetected TruthValue, arubaWiredLoopProtectPortLastLoopTime TimeStamp, arubaWiredLoopProtectPortLoopCount Counter32, arubaWiredLoopProtectPortReceiverAction LoopProtectReceiverAction, arubaWiredLoopProtectLoopDetectedVlan Integer32, arubaWiredLoopProtectPortVlanList VidList } arubaWiredLoopProtectPortInterfaceIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex." ::= { arubaWiredLoopProtectPortEntry 1 } arubaWiredLoopProtectPortEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the Loop Protection is enabled on a port. The default value is FALSE" ::= { arubaWiredLoopProtectPortEntry 2 } arubaWiredLoopProtectPortLoopDetected OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object will be set to TRUE when a loop is detected on the port. The value of this object will be reset to FALSE when the port's arubaWiredLoopProtectPortEnable is set to FALSE." ::= { arubaWiredLoopProtectPortEntry 3 } arubaWiredLoopProtectPortLastLoopTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when a loop was last detected on this port. A value of 0 means that the timestamp has not been set." ::= { arubaWiredLoopProtectPortEntry 4 } arubaWiredLoopProtectPortLoopCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the number of loops detected on a Loop Protection enabled port. The value of this object is set to zero when Loop Protection is disabled on a port." ::= { arubaWiredLoopProtectPortEntry 5 } arubaWiredLoopProtectPortReceiverAction OBJECT-TYPE SYNTAX LoopProtectReceiverAction MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the action taken when a Loop Protection packet is received on this port. When set to 'disableTx' the port that transmitted the packet is disabled. When set to 'noDisable' the transmitting port is not disabled. When set to 'disableTxRx' the ports transmitting and receiving the packets are disabled." ::= { arubaWiredLoopProtectPortEntry 6 } arubaWiredLoopProtectLoopDetectedVlan OBJECT-TYPE SYNTAX Integer32(0..4096) MAX-ACCESS read-only STATUS current DESCRIPTION "The loop-detected VLAN ID. A value of 0 indicates no loop." ::= { arubaWiredLoopProtectPortEntry 7 } arubaWiredLoopProtectPortVlanList OBJECT-TYPE SYNTAX VidList MAX-ACCESS read-write STATUS current DESCRIPTION "A list of VLANs for this interface in which Loop Protection is enabled." ::= { arubaWiredLoopProtectPortEntry 8 } -- ********************************************************************** -- arubaWiredLoopProtect Notifications -- ********************************************************************** arubaWiredLoopProtectLoopDetectedNotification NOTIFICATION-TYPE OBJECTS { ifIndex, arubaWiredLoopProtectPortLoopCount, arubaWiredLoopProtectPortReceiverAction } STATUS current DESCRIPTION "A arubaWiredLoopProtectLoopDetectedNotification signifies that a loop is detected by the Loop Protection Protocol. Generation of this notification is controlled by arubaWiredLoopProtectTrapLoopDetectEnable. To prevent excessive notifications, this trap allows only one notifications every 30 seconds. Notifications that are missed due to this limitation are dropped and are not sent later." ::= { arubaWiredLoopProtectNotifications 1 } arubaWiredLoopProtectVlanLoopDetectedNotification NOTIFICATION-TYPE OBJECTS { ifIndex, arubaWiredLoopProtectPortLoopCount, arubaWiredLoopProtectPortReceiverAction, arubaWiredLoopProtectLoopDetectedVlan } STATUS current DESCRIPTION "A arubaWiredLoopProtectVlanLoopDetectedNotification signifies that a loop is detected by the Loop Protection feature while operating in VLAN mode. Generation of this notification is controlled by arubaWiredLoopProtectTrapLoopDetectEnable. To prevent excessive notifications, this trap allows only one notifications every 30 seconds. Notifications that are missed due to this limitation are dropped and are not sent later." ::= { arubaWiredLoopProtectNotifications 2 } -- ********************************************************************** -- Conformance information -- ********************************************************************** arubaWiredLoopProtectConformance OBJECT IDENTIFIER ::= { arubaWiredLoopProtect 3 } arubaWiredLoopProtectGroups OBJECT IDENTIFIER ::= { arubaWiredLoopProtectConformance 1 } arubaWiredLoopProtectCompliances OBJECT IDENTIFIER ::= { arubaWiredLoopProtectConformance 2 } arubaWiredLoopProtectBaseGroup OBJECT-GROUP OBJECTS { arubaWiredLoopProtectInterval, arubaWiredLoopProtectEnableTimer, arubaWiredLoopProtectTrapLoopDetectEnable, arubaWiredLoopProtectPortEnable, arubaWiredLoopProtectPortLoopDetected, arubaWiredLoopProtectPortLastLoopTime, arubaWiredLoopProtectPortLoopCount, arubaWiredLoopProtectPortReceiverAction } STATUS current DESCRIPTION "A collection of objects providing basic instrumentation and control of the HP Loop protection entity." ::= {arubaWiredLoopProtectGroups 4 } arubaWiredLoopProtectVLANGroup OBJECT-GROUP OBJECTS { arubaWiredLoopProtectMode, arubaWiredLoopProtectVIDList, arubaWiredLoopProtectLoopDetectedVlan, arubaWiredLoopProtectPortVlanList } STATUS current DESCRIPTION "A collection of objects providing support for Loop Protect per VLAN feature." ::= {arubaWiredLoopProtectGroups 10 } arubaWiredLoopProtectNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { arubaWiredLoopProtectLoopDetectedNotification, arubaWiredLoopProtectVlanLoopDetectedNotification } STATUS current DESCRIPTION "Aruba Wired Loop Protect notification group." ::= { arubaWiredLoopProtectGroups 11 } arubaWiredLoopProtectCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for HP Switches with support for arubaWired loop protection objects." MODULE MANDATORY-GROUPS { arubaWiredLoopProtectBaseGroup, arubaWiredLoopProtectNotificationsGroup, arubaWiredLoopProtectVLANGroup } ::= { arubaWiredLoopProtectCompliances 5 } END