-- -- phyVdsl.mib -- MIB generated by MG-SOFT Visual MIB Builder Version 3.0 Build 285 -- Thursday, October 10, 2013 at 07:01:35 -- ZhoneVdsl-MIB DEFINITIONS ::= BEGIN IMPORTS HCPerfTimeElapsed, HCPerfCurrentCount, HCPerfIntervalCount FROM HC-PerfHist-TC-MIB ifIndex FROM IF-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP FROM SNMPv2-CONF transmission, Integer32, Unsigned32, Gauge32, OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE FROM SNMPv2-SMI RowStatus, TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC zhoneVdsl, zhoneModules FROM Zhone; -- Overview of Zhone VDSL mib -- -- This MIB file is based on RFC3728. -- -- The Zhone DSL mib provides configuration, status and performance parameters -- used/provided by Zhone implementation of VDSL2 interfaces. -- The following tables are described in this mib: -- -- zhoneVdsLineConfProfileTable -- This table provides VDSL specific configuration parameters. It contains the VDSL -- profiles ( Config, CPE, and CO ). This table is indexed by ifIndex. -- -- zhoneVdslCustomNotchTable -- This table contains HAM (Handheld Amateur Radio) custom notch information. -- This table supports more entries than the standard RFC. -- -- -- -- -- -- -- -- -- -- -- 1.3.6.1.4.1.5504.6.110 zhoneVdslMib MODULE-IDENTITY LAST-UPDATED "201302271600Z" -- February 27, 2013 at 16:00 GMT ORGANIZATION "ADSLMIB Working Group" CONTACT-INFO "WG-email: adslmib@ietf.org Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh, NC 27627-7324 USA Email: sneedmike@hotmail.com Phone: +1 206 600 7022 Co-editor: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142 Co-editor: Rajesh Abbi Alcatel USA Postal: 2301 Sugar Bush Road Raleigh, NC 27612-3339 USA Email: Rajesh.Abbi@alcatel.com Phone: +1 919 850 6194 " DESCRIPTION "The MIB module defining objects for the management of a pair of VDSL transceivers at each end of the VDSL line. Each such line has an entry in an ifTable which may include multiple transceiver lines. An agent may reside at either end of the VDSL line. However, the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs. VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. SES -- Severely Errored Second UAS -- Unavailable Second LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs -- Sum of Seconds in which xxx has occured (e.g., xxx = Lof, Los, Lpr, Lol) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks -- Blocks Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFC 3728: see the RFC itself for full legal notices." REVISION "201310080643Z" -- October 08, 2013 at 06:43 GMT DESCRIPTION "Add ATM or PTM transport mode retrieval support" REVISION "201302271800Z" -- February 27, 2013 at 18:00 GMT DESCRIPTION "Adding support for G.INP / ITU-T G.998.4" REVISION "201302111415Z" -- February 11, 2013 at 14:15 GMT DESCRIPTION "Add VDSL2 Vectoring statistics retrieval support." REVISION "201112010559Z" -- December 01, 2011 at 05:59 GMT DESCRIPTION "V.01.24 - fix vpi/vci valid ranges" REVISION "201111161214Z" -- November 16, 2011 at 12:14 GMT DESCRIPTION "V.01.24 - add default VPI/VCI for line when its in single-vc mode" REVISION "201110181113Z" -- October 18, 2011 at 11:13 GMT DESCRIPTION "V.01.23 - add A3/A4/B3/B4 parameters for UPBO configuration" REVISION "201110141124Z" -- October 14, 2011 at 11:24 GMT DESCRIPTION "V.01.22 - split psdShape for Hytec into two shapes for 17a and 30a" REVISION "201104281155Z" -- April 28, 2011 at 11:55 GMT DESCRIPTION "V.01.21 - add new PSD Shape values and fix units for SNR and Attn" REVISION "201011050716Z" -- November 05, 2010 at 07:16 GMT DESCRIPTION "V.01.20 Modify defaults for max power and max SNR" REVISION "201010130459Z" -- October 13, 2010 at 04:59 GMT DESCRIPTION "V.01.19 -added zhoneVdslPhysPhyRActive object " REVISION "201006071129Z" -- June 07, 2010 at 11:29 GMT DESCRIPTION "V.01.18 VDSL upstream minINP values expanded" REVISION "201005310011Z" -- May 31, 2010 at 00:11 GMT DESCRIPTION "V.01.17 VDSL phyR Statistics Objects are added" REVISION "201004020640Z" -- April 02, 2010 at 06:40 GMT DESCRIPTION "V.01.16 - modified defaults for zhoneVdslLineConfLineType to fastOnly, zhoneVdslLineConfDownPhyRSupport and zhoneVdslLineConfUpPhyRSupport to enable. " REVISION "201003290554Z" -- March 29, 2010 at 05:54 GMT DESCRIPTION "V.01.15 Expanded lower end of range on zhoneVdslLineConfDownMaxPwr, zhoneVdslLineConfUpMaxPwr" REVISION "201003020844Z" -- March 02, 2010 at 08:44 GMT DESCRIPTION "V.01.14 Added zhoneVdslLineConfProfileEntry objects 113-123 to support BroadCOM VDSL." REVISION "200804141228Z" -- April 14, 2008 at 12:28 GMT DESCRIPTION "V.01.13 - cleanup traps - config SNR values changed from 0..127 to 0.310 in 1/10 DBm steps." REVISION "200802050856Z" -- February 05, 2008 at 08:56 GMT DESCRIPTION "V.01.12 - add more values to zhoneVdslLineConfDownPsdMaskSelect - add more values to zhoneVdslLineConfUpPsdMaskSelect" REVISION "200710231653Z" -- October 23, 2007 at 16:53 GMT DESCRIPTION "V.01.11 - add more values to zhoneVdslLineConfDownPsdMaskSelect - add more values to zhoneVdslLineConfUppsdMaskSelect" REVISION "200710051324Z" -- October 05, 2007 at 13:24 GMT DESCRIPTION "V.01.10 - Add zhoneVdslPhysCurrConnType - Add zhoneVdslPhysCurrProfile" REVISION "200706201056Z" -- June 20, 2007 at 10:56 GMT DESCRIPTION "V.01.09 Accelity-2 additions - Add 'dynamic' option to zhoneVdslLineConfDownRateMode - Add 'dynamic' option to zhoneVdslLineConfUpRateMode - Add zhoneVdslLineConfDownBitSwap - Add zhoneVdslLineConfUpBitSwap - Add zhoneVdslLineConfAdslAnnexMModeEnabled - Add zhoneVdslLineConfAdslAnnexMPsdMask - Add zhoneVdslLineConfUS0BoundaryTone - Add zhoneVdslLineConfDownInp - Add zhoneVdslLineConfUpInp - Add zhoneVdslLineConfDownMaxInterleavingDelay - Add zhoneVdslLineConfUpMaxInterleavingDelay - Add zhoneVdslLineConfDownPsdMaskEnable - Add zhoneVdslLineConfUpPsdMaskEnable - Add zhoneVdslLineConfDownPsdMaskSelect - Add zhoneVdslLineConfUpPsdMaskSelect" REVISION "200703141608Z" -- March 14, 2007 at 16:08 GMT DESCRIPTION "V.01.08 - ADSL Fallback additions - add ADSL transmission modes - add ADSL objects to VDSL CO Profile - add ADSL objecst to VDSL CPE Profile" REVISION "200612051509Z" -- December 05, 2006 at 15:09 GMT DESCRIPTION "V.01.07 - modify zhoneVdslLineConfUpMaxAggregateTxPwr to conform with Conexant driver - modify zhoneVdslLineConfDownMaxAggregateTxPwr to conform with Conexant driver - mark up mib for vdslPerfDataTable - mark up mib for vdslChanPerfDataTable - In ZhoneVdslChanPerfDataTable, convert Counter64 objects to Integer32 objects. " REVISION "200611100858Z" -- November 10, 2006 at 08:58 GMT DESCRIPTION "V.01.06 - modify zhoneVdslLineConfDownPsdShape to conform with Conexant driver values - modify zhoneVdslLineConfUpPsdShape to conform with Conexant driver values" REVISION "200610101525Z" -- October 10, 2006 at 15:25 GMT DESCRIPTION "V.01.05 - zhoneVdslLineAlarmConfProfileEntry is now indexed by ifIndex - add MIN/MAX values - add zhoneVdslPhysStatus ZHONE KEYWORDS - add zhoneVdslChanStatus ZHONE KEYWORDS - make phyVdsl.mib reflect new default values - vdslConfig: line-type - vdslConfig: band-opt-uasge - vdslCoConfig: pbo-control - vdslCoConfig: trellis - vdslCpeConfig: pbo-control - vdslCpeConfig: psd-template - vdslCpeConfig: trellis - fix spelling zhoneVdslLineConfDownGhsA43cTonePwr - cleanup min/max data rates and def values for them" REVISION "200609101116Z" -- September 10, 2006 at 11:16 GMT DESCRIPTION "V.01.04 - rename zhoneVdslLineConfSeltNoiseMeasurementTme to zhoneVdslLineConfSeltNoiseMeasurementTime" REVISION "200608221721Z" -- August 22, 2006 at 17:21 GMT DESCRIPTION "V.01.03 - move tables from phyDsl.mib - move zhoneVdslStatusTable from phyDsl.mib - move zhoneVdslPerfTable from phyDsl.mib " REVISION "200606151529Z" -- June 15, 2006 at 15:29 GMT DESCRIPTION "V01.02 - add ZHONE-KEYWORDS" REVISION "200402190000Z" -- February 19, 2004 at 00:00 GMT DESCRIPTION "Initial version, published as RFC 3728." ::= { zhoneModules 110 } -- -- Textual conventions -- -- Textual conventions -- -- textual conventions used in this MIB -- ZhoneVdslLineCodingType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used as the syntax for the VDSL Line Code. Attributes with this syntax identify the line coding used. Specified as an INTEGER, the three values are: other(1) -- none of the following mcm(2) -- Multiple Carrier Modulation scm(3) -- Single Carrier Modulation" SYNTAX INTEGER { other(1), mcm(2), scm(3) } ZhoneVdslLineEntity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Identifies a transceiver as being either Vtuc or Vtur. A VDSL line consists of two transceivers, a Vtuc and a Vtur. Attributes with this syntax reference the two sides of a line. Specified as an INTEGER, the two values are: vtuc(1) -- central site transceiver vtur(2) -- remote site transceiver" SYNTAX INTEGER { vtuc(1), vtur(2) } -- -- Node definitions -- -- Node definitions -- -- 1.3.6.1.4.1.5504.5.13.1 -- 1.3.6.1.4.1.5504.5.13.1 zhoneVdslLineMib OBJECT IDENTIFIER ::= { zhoneVdsl 1 } -- Notification definitions -- 1.3.6.1.4.1.5504.5.13.1.0 -- 1.3.6.1.4.1.5504.5.13.1.0 zhoneVdslNotifications OBJECT IDENTIFIER ::= { zhoneVdslLineMib 0 } -- 1.3.6.1.4.1.5504.5.13.1.0.1 vdslXtucPerf15MinLofsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold (vdslLineAlarmConfThresh15MinLofs) reached." ::= { zhoneVdslNotifications 1 } -- 1.3.6.1.4.1.5504.5.13.1.0.2 vdslXtucPerf15MinLossThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold (vdslLineAlarmConfThresh15MinLoss) reached." ::= { zhoneVdslNotifications 2 } -- 1.3.6.1.4.1.5504.5.13.1.0.3 vdslXtucPerf15MinLprsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold (vdslLineAlarmConfThresh15MinLprs) reached." ::= { zhoneVdslNotifications 3 } -- 1.3.6.1.4.1.5504.5.13.1.0.4 vdslXtucPerf15MinLolsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr15MinLols } STATUS current DESCRIPTION "Loss of Link 15-minute interval threshold (vdslLineAlarmConfThresh15MinLols) reached." ::= { zhoneVdslNotifications 4 } -- 1.3.6.1.4.1.5504.5.13.1.0.5 vdslXtucPerf15MinESsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr15MinESs } STATUS current DESCRIPTION "Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinESs) reached." ::= { zhoneVdslNotifications 5 } -- 1.3.6.1.4.1.5504.5.13.1.0.6 vdslXtucPerf15MinSESsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr15MinSESs } STATUS current DESCRIPTION "Severely Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinSESs) reached." ::= { zhoneVdslNotifications 6 } -- 1.3.6.1.4.1.5504.5.13.1.0.7 vdslXtucPerf15MinUASsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr15MinUASs } STATUS current DESCRIPTION "Unavailable Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinUASs) reached." ::= { zhoneVdslNotifications 7 } -- 1.3.6.1.4.1.5504.5.13.1.0.8 vdslXtucPerf1DayLofsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr1DayLofs } STATUS current DESCRIPTION "Loss of Framing 1-day interval threshold (vdslLineAlarmConfThresh1DayLofs) reached." ::= { zhoneVdslNotifications 8 } -- 1.3.6.1.4.1.5504.5.13.1.0.9 vdslXtucPerf1DayLossThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr1DayLoss } STATUS current DESCRIPTION "Loss of Signal 1-day interval threshold (vdslLineAlarmConfThresh1DayLoss) reached." ::= { zhoneVdslNotifications 9 } -- 1.3.6.1.4.1.5504.5.13.1.0.10 vdslXtucPerf1DayLprsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr1DayLprs } STATUS current DESCRIPTION "Loss of Power 1-day interval threshold (vdslLineAlarmConfThresh1DayLprs) reached." ::= { zhoneVdslNotifications 10 } -- 1.3.6.1.4.1.5504.5.13.1.0.11 vdslXtucPerf1DayLolsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr1DayLols } STATUS current DESCRIPTION "Loss of Link 1-day interval threshold (vdslLineAlarmConfThresh1DayLols) reached." ::= { zhoneVdslNotifications 11 } -- 1.3.6.1.4.1.5504.5.13.1.0.12 vdslXtucPerf1DayESsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr1DayESs } STATUS current DESCRIPTION "Errored Seconds 1-day interval threshold (vdslLineAlarmConfThresh1DayESs) reached." ::= { zhoneVdslNotifications 12 } -- 1.3.6.1.4.1.5504.5.13.1.0.13 vdslXtucPerf1DaySESsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr1DaySESs } STATUS current DESCRIPTION "Severely Errored Seconds 1-day interval threshold (vdslLineAlarmConfThresh1DaySESs) reached." ::= { zhoneVdslNotifications 13 } -- 1.3.6.1.4.1.5504.5.13.1.0.14 vdslXtucPerf1DayUASsThreshTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataCurr1DayUASs } STATUS current DESCRIPTION "Unavailable Seconds 1-day interval threshold (vdslLineAlarmConfThresh1DayUASs) reached." ::= { zhoneVdslNotifications 14 } -- 1.3.6.1.4.1.5504.5.13.1.0.12 -- 1.3.6.1.4.1.5504.5.13.1.0.15 zhoneVdslInitFailureTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslPerfDataInits } STATUS current DESCRIPTION "Vtu initialization failed. " ::= { zhoneVdslNotifications 15 } -- 1.3.6.1.4.1.5504.5.13.1.0.16 vdslXtucMinTxThresholdAlarmFailureTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslChanCurrTxRate, zhoneVdslLineConfDownMinTxThresholdAlarm } STATUS current DESCRIPTION "This trap is thrown when the XTUC line rate syncs below the threshold rate as defined by zhoneVdslLineConfDownMinTxThresholdAlarm." ::= { zhoneVdslNotifications 16 } -- 1.3.6.1.4.1.5504.5.13.1.0.17 vdslXturMinTxThresholdAlarmFailureTrap NOTIFICATION-TYPE OBJECTS { zhoneVdslChanCurrTxRate, zhoneVdslLineConfUpMinTxThresholdAlarm } STATUS current DESCRIPTION "This trap is thrown when the XTUR line rate syncs below the threshold rate as defined by zhoneVdslLineConfUpMinTxThresholdAlarm." ::= { zhoneVdslNotifications 17 } -- 1.3.6.1.4.1.5504.5.13.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1 zhoneVdslMibObjects OBJECT IDENTIFIER ::= { zhoneVdslLineMib 1 } -- objects -- -- 1.3.6.1.4.1.5504.5.13.1.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.1 zhoneVdslLineTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing both ends of the line. It is required for all VDSL physical interfaces. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { zhoneVdslMibObjects 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.1.1 zhoneVdslLineEntry OBJECT-TYPE SYNTAX ZhoneVdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslLineTable." INDEX { ifIndex } ::= { zhoneVdslLineTable 1 } ZhoneVdslLineEntry ::= SEQUENCE { zhoneVdslLineCoding ZhoneVdslLineCodingType, zhoneVdslLineType INTEGER, zhoneVdslLineConfProfile SnmpAdminString, zhoneVdslLineAlarmConfProfile SnmpAdminString } -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.1 zhoneVdslLineCoding OBJECT-TYPE SYNTAX ZhoneVdslLineCodingType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the VDSL coding type used on this line." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslLineEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.2 -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.2 zhoneVdslLineType OBJECT-TYPE SYNTAX INTEGER { noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of VDSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exist, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s)." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslLineEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.3 -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.3 zhoneVdslLineConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the VDSL Line Configuration Profile Table, zhoneVdslLineConfProfileTable, which applies for this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner." DEFVAL { "DEFVAL" } ::= { zhoneVdslLineEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.4 -- 1.3.6.1.4.1.5504.5.13.1.1.1.1.4 zhoneVdslLineAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the VDSL Line Alarm Configuration Profile Table, zhoneVdslLineAlarmConfProfileTable, which applies to this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner." DEFVAL { "DEFVAL" } ::= { zhoneVdslLineEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.2 -- 1.3.6.1.4.1.5504.5.13.1.1.2 zhoneVdslPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu. Each row contains the Physical Layer Parameters table for that Vtu. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { zhoneVdslMibObjects 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1 -- 1.3.6.1.4.1.5504.5.13.1.1.2.1 zhoneVdslPhysEntry OBJECT-TYPE SYNTAX ZhoneVdslPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPhysTable." INDEX { ifIndex, zhoneVdslPhysSide } ::= { zhoneVdslPhysTable 1 } ZhoneVdslPhysEntry ::= SEQUENCE { zhoneVdslPhysSide ZhoneVdslLineEntity, zhoneVdslPhysInvSerialNumber OCTET STRING, zhoneVdslPhysInvVendorID OCTET STRING, zhoneVdslPhysInvVersionNumber OCTET STRING, zhoneVdslPhysCurrSnrMgn Integer32, zhoneVdslPhysCurrAtn Gauge32, zhoneVdslPhysCurrStatus BITS, zhoneVdslPhysCurrOutputPwr Integer32, zhoneVdslPhysCurrAttainableRate Gauge32, zhoneVdslPhysCurrLineRate Gauge32, zhoneVdslPhysCurrConnType INTEGER, zhoneVdslPhysCurrProfile INTEGER, zhoneVdslPhysPhyRActive TruthValue, zhoneVdslPhysGinpActive TruthValue, zhoneVdslPhysTransportMode INTEGER } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.1 zhoneVdslPhysSide OBJECT-TYPE SYNTAX ZhoneVdslLineEntity MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies whether the transceiver is the Vtuc or Vtur." ::= { zhoneVdslPhysEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.2 zhoneVdslPhysInvSerialNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific string that identifies the vendor equipment." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.3 zhoneVdslPhysInvVendorID OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID code is a copy of the binary vendor identification field expressed as readable characters in hexadecimal notation." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.4 zhoneVdslPhysInvVersionNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field expressed as readable characters in hexadecimal notation." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.5 zhoneVdslPhysCurrSnrMgn OBJECT-TYPE SYNTAX Integer32 (-127..127) UNITS "0.10dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this Vtu with respect to its received signal in 0.10dB. The effective range is -31.75 to +31.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.6 zhoneVdslPhysCurrAtn OBJECT-TYPE SYNTAX Gauge32 (0..255) UNITS "0.10dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu. The effective range is 0 to +63.75 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.7 zhoneVdslPhysCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerVtuPresent(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There are no defects on the line. 1 lossOfFraming Vtu failure due to not receiving a valid frame. 2 lossOfSignal Vtu failure due to not receiving signal. 3 lossOfPower Vtu failure due to loss of power. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink Vtu failure due to inability to link with peer Vtu. Set whenever the transceiver is in the 'Warm Start' state. 6 dataInitFailure Vtu failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure Vtu failure during initialization due to peer Vtu not able to support requested configuration. 8 protocolInitFailure Vtu failure during initialization due to incompatible protocol used by the peer Vtu. 9 noPeerVtuPresent Vtu failure during initialization due to no activation sequence detected from peer Vtu. This is intended to supplement ifOperStatus." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.8 zhoneVdslPhysCurrOutputPwr OBJECT-TYPE SYNTAX Integer32 (0..160) UNITS "0.1dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this VTU. This is the measurement that was reported during the last activation sequence." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.9 zhoneVdslPhysCurrAttainableRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate in steps of 1000 bits/second by the Vtu. This value will be equal to or greater than vdslPhysCurrLineRate. Note that for SCM, the minimum and maximum data rates are equal. Note: 1 kbps = 1000 bps." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.10 zhoneVdslPhysCurrLineRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current data rate in steps of 1000 bits/second by the Vtu. This value will be less than or equal to vdslPhysCurrAttainableRate. Note: 1 kbps = 1000 bps." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 10 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.12 zhoneVdslPhysCurrConnType OBJECT-TYPE SYNTAX INTEGER { unknown(1), not-connected(2), invalid(3), adsl(4), adsl2(5), adsl2-annexm(6), adsl2plus(7), adsl2plus-annexm(8), vdsl1(9), vdsl2(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current connection type. unknown(1) - could not determine connection type not-connected(2) - connection has not been established invalid(3) - unknown connection established adsl(4) - G.992.1/2 adsl2(5) - G.992.3/4 adsl2-annexm(6) - G.992.3/4 with Annex M adsl2plus(7) - G.992.5 adsl2plus-annexm(8) - G.992.5 with Annex M vdsl1(9) - G.993.1 vdsl2(10) - G.993.2 " REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 12 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.13 zhoneVdslPhysCurrProfile OBJECT-TYPE SYNTAX INTEGER { g993-2-8a(1), g993-2-8b(2), g993-2-8c(3), g993-2-8d(4), g993-2-12a(5), g993-2-12b(6), g993-2-17a(7), g993-2-30a(8), no-vdsl-connection(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current VDSL profile being used in the connection. This object is only valid for VDSL connections." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPhysEntry 13 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.14 zhoneVdslPhysPhyRActive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Phy Retransmit Rx Queue Active." ::= { zhoneVdslPhysEntry 14 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.15 zhoneVdslPhysGinpActive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "G.INP/ITU-G.998.4 feature active" REFERENCE "ITU-G.998.4" ::= { zhoneVdslPhysEntry 15 } -- 1.3.6.1.4.1.5504.5.13.1.1.2.1.16 zhoneVdslPhysTransportMode OBJECT-TYPE SYNTAX INTEGER { atm(1), ptm(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Transport mode, either ATM or PTM" ::= { zhoneVdslPhysEntry 16 } -- 1.3.6.1.4.1.5504.5.13.1.1.3 -- 1.3.6.1.4.1.5504.5.13.1.1.3 zhoneVdslChanTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125)." ::= { zhoneVdslMibObjects 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.3.1 -- 1.3.6.1.4.1.5504.5.13.1.1.3.1 zhoneVdslChanEntry OBJECT-TYPE SYNTAX ZhoneVdslChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChanTable." INDEX { ifIndex, zhoneVdslPhysSide } ::= { zhoneVdslChanTable 1 } ZhoneVdslChanEntry ::= SEQUENCE { zhoneVdslChanInterleaveDelay Gauge32, zhoneVdslChanCrcBlockLength Gauge32, zhoneVdslChanCurrTxRate Gauge32, zhoneVdslChanCurrTxSlowBurstProtect Gauge32, zhoneVdslChanCurrTxFastFec Gauge32 } -- 1.3.6.1.4.1.5504.5.13.1.1.3.1.1 zhoneVdslChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave (slow) channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is fast(125), return a value of zero." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.3.1.2 zhoneVdslChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.3.1.3 zhoneVdslChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit data rate on this channel. Note: 1 kbps = 1000 bps." ::= { zhoneVdslChanEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.3.1.4 zhoneVdslChanCurrTxSlowBurstProtect OBJECT-TYPE SYNTAX Gauge32 (0..1275) UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual level of impulse noise (burst) protection for an interleaved (slow) channel. This parameter is not applicable to fast channels. For fast channels, a value of zero shall be returned." REFERENCE "ITU-T G.997.1, section 7.3.2.3" ::= { zhoneVdslChanEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.3.1.5 zhoneVdslChanCurrTxFastFec OBJECT-TYPE SYNTAX Gauge32 (0..50) UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Forward Error Correction (FEC) redundancy related overhead for a fast channel. This parameter is not applicable to an interleaved (slow) channel. For interleaved channels, a value of zero shall be returned." ::= { zhoneVdslChanEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.4 -- 1.3.6.1.4.1.5504.5.13.1.1.4 zhoneVdslPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each VDSL physical interface. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { zhoneVdslMibObjects 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1 -- 1.3.6.1.4.1.5504.5.13.1.1.4.1 zhoneVdslPerfDataEntry OBJECT-TYPE SYNTAX ZhoneVdslPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPerfDataTable." INDEX { ifIndex, zhoneVdslPhysSide } ::= { zhoneVdslPerfDataTable 1 } ZhoneVdslPerfDataEntry ::= SEQUENCE { zhoneVdslPerfDataValidIntervals Integer32, zhoneVdslPerfDataInvalidIntervals Integer32, zhoneVdslPerfDataLofs Unsigned32, zhoneVdslPerfDataLoss Unsigned32, zhoneVdslPerfDataLprs Unsigned32, zhoneVdslPerfDataLols Unsigned32, zhoneVdslPerfDataESs Unsigned32, zhoneVdslPerfDataSESs Unsigned32, zhoneVdslPerfDataUASs Unsigned32, zhoneVdslPerfDataInits Unsigned32, zhoneVdslPerfDataCurr15MinTimeElapsed Integer32, zhoneVdslPerfDataCurr15MinLofs Unsigned32, zhoneVdslPerfDataCurr15MinLoss Unsigned32, zhoneVdslPerfDataCurr15MinLprs Unsigned32, zhoneVdslPerfDataCurr15MinLols Unsigned32, zhoneVdslPerfDataCurr15MinESs Unsigned32, zhoneVdslPerfDataCurr15MinSESs Unsigned32, zhoneVdslPerfDataCurr15MinUASs Unsigned32, zhoneVdslPerfDataCurr15MinInits Unsigned32, zhoneVdslPerfData1DayValidIntervals Integer32, zhoneVdslPerfData1DayInvalidIntervals Integer32, zhoneVdslPerfDataCurr1DayTimeElapsed Integer32, zhoneVdslPerfDataCurr1DayLofs Unsigned32, zhoneVdslPerfDataCurr1DayLoss Unsigned32, zhoneVdslPerfDataCurr1DayLprs Unsigned32, zhoneVdslPerfDataCurr1DayLols Unsigned32, zhoneVdslPerfDataCurr1DayESs Unsigned32, zhoneVdslPerfDataCurr1DaySESs Unsigned32, zhoneVdslPerfDataCurr1DayUASs Unsigned32, zhoneVdslPerfDataCurr1DayInits Unsigned32, zhoneVdslPhyrRetransmittedCodewords Unsigned32, zhoneVdslPhyrCorrectedRetransmittedCodewords Unsigned32, zhoneVdslPhyrUncorrectableRetransmittedCodewords Unsigned32, zhoneVdslPhyrCurr15MinRetransmittedCodewords Unsigned32, zhoneVdslPhyrCurr15MinCorrectedRetransmittedCodewords Unsigned32, zhoneVdslPhyrCurr15MinUncorrectableRetransmittedCodewords Unsigned32, zhoneVdslPhyrCurr1DayRetransmittedCodewords Unsigned32, zhoneVdslPhyrCurr1DayCorrectedRetransmittedCodewords Unsigned32, zhoneVdslPhyrCurr1DayUncorrectableRetransmittedCodewords Unsigned32, zhoneVdslPhyrPrev1DayRetransmittedCodewords Unsigned32, zhoneVdslPhyrPrev1DayCorrectedRetransmittedCodewords Unsigned32, zhoneVdslPhyrPrev1DayUncorrectableRetransmittedCodewords Unsigned32, zhoneVdslGinpLeftrSecs Unsigned32, zhoneVdslGinpErrorFreeBits Unsigned32, zhoneVdslGinpMinEftr Unsigned32, zhoneVdslGinpCurr15MinLeftrSecs Unsigned32, zhoneVdslGinpCurr15MinErrorFreeBits Unsigned32, zhoneVdslGinpCurr15MinMinEftr Unsigned32, zhoneVdslGinpCurr1DayLeftrSecs Unsigned32, zhoneVdslGinpCurr1DayErrorFreeBits Unsigned32, zhoneVdslGinpCurr1DayMinEftr Unsigned32, zhoneVdslGinpPrev1DayLeftrSecs Integer32, zhoneVdslGinpPrev1DayErrorFreeBits Integer32, zhoneVdslGinpPrev1DayMinEftr Integer32 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.1 zhoneVdslPerfDataValidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslPerfDataEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.2 zhoneVdslPerfDataInvalidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslPerfDataEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.3 zhoneVdslPerfDataLofs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Framing." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.4 zhoneVdslPerfDataLoss OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Signal." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.5 zhoneVdslPerfDataLprs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Power." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.6 zhoneVdslPerfDataLols OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds since the unit was last reset that there was Loss of Link." ::= { zhoneVdslPerfDataEntry 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.7 zhoneVdslPerfDataESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds since the unit was last reset. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.8 zhoneVdslPerfDataSESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds since the unit was last reset." ::= { zhoneVdslPerfDataEntry 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.9 zhoneVdslPerfDataUASs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds since the unit was last reset." ::= { zhoneVdslPerfDataEntry 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.10 zhoneVdslPerfDataInits OBJECT-TYPE SYNTAX Unsigned32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts since the unit was last reset. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 10 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.11 zhoneVdslPerfDataCurr15MinTimeElapsed OBJECT-TYPE SYNTAX Integer32 (0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { zhoneVdslPerfDataEntry 11 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.12 zhoneVdslPerfDataCurr15MinLofs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Framing." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 12 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.13 zhoneVdslPerfDataCurr15MinLoss OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Signal." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 13 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.14 zhoneVdslPerfDataCurr15MinLprs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Power." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 14 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.15 zhoneVdslPerfDataCurr15MinLols OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval that there was Loss of Link." ::= { zhoneVdslPerfDataEntry 15 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.16 zhoneVdslPerfDataCurr15MinESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during this interval. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 16 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.17 zhoneVdslPerfDataCurr15MinSESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds during this interval." ::= { zhoneVdslPerfDataEntry 17 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.18 zhoneVdslPerfDataCurr15MinUASs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds during this interval." ::= { zhoneVdslPerfDataEntry 18 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.19 zhoneVdslPerfDataCurr15MinInits OBJECT-TYPE SYNTAX Unsigned32 UNITS "occurrences" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during this interval. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfDataEntry 19 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.20 zhoneVdslPerfData1DayValidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslPerfDataEntry 20 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.21 zhoneVdslPerfData1DayInvalidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslPerfDataEntry 21 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.22 zhoneVdslPerfDataCurr1DayTimeElapsed OBJECT-TYPE SYNTAX Integer32 (0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 22 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.23 zhoneVdslPerfDataCurr1DayLofs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Framing (LOF) Seconds since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 23 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.24 zhoneVdslPerfDataCurr1DayLoss OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Signal (LOS) Seconds since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 24 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.25 zhoneVdslPerfDataCurr1DayLprs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Power (LPR) Seconds since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 25 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.26 zhoneVdslPerfDataCurr1DayLols OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Link (LOL) Seconds since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 26 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.27 zhoneVdslPerfDataCurr1DayESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 27 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.28 zhoneVdslPerfDataCurr1DaySESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 28 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.29 zhoneVdslPerfDataCurr1DayUASs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) since the beginning of the current 1-day interval." ::= { zhoneVdslPerfDataEntry 29 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.30 zhoneVdslPerfDataCurr1DayInits OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts since the beginning of the current 1-day interval. This count includes both successful and failed attempts." ::= { zhoneVdslPerfDataEntry 30 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.31 zhoneVdslPhyrRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmitted Codewords" ::= { zhoneVdslPerfDataEntry 31 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.32 zhoneVdslPhyrCorrectedRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmitted corrected Codewords" ::= { zhoneVdslPerfDataEntry 32 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.33 zhoneVdslPhyrUncorrectableRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmitted uncorrectable Codewords" ::= { zhoneVdslPerfDataEntry 33 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.34 zhoneVdslPhyrCurr15MinRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current 15 minutes Retransmitted Codewords" ::= { zhoneVdslPerfDataEntry 34 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.35 zhoneVdslPhyrCurr15MinCorrectedRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current 15 minutes Retransmitted Corrected Codewords" ::= { zhoneVdslPerfDataEntry 35 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.36 zhoneVdslPhyrCurr15MinUncorrectableRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current 15 minutes Retransmitted Uncorrectable Codewords" ::= { zhoneVdslPerfDataEntry 36 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.37 zhoneVdslPhyrCurr1DayRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current Day Retransmitted Codewords" ::= { zhoneVdslPerfDataEntry 37 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.38 zhoneVdslPhyrCurr1DayCorrectedRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current Day Retransmitted Corrected Codewords" ::= { zhoneVdslPerfDataEntry 38 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.39 zhoneVdslPhyrCurr1DayUncorrectableRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current Day Retransmitted Uncorrectable Codewords" ::= { zhoneVdslPerfDataEntry 39 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.40 zhoneVdslPhyrPrev1DayRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Previous Day Retransmitted Codewords" ::= { zhoneVdslPerfDataEntry 40 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.41 zhoneVdslPhyrPrev1DayCorrectedRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Previous Day Retransmitted Corrected Codewords" ::= { zhoneVdslPerfDataEntry 41 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.42 zhoneVdslPhyrPrev1DayUncorrectableRetransmittedCodewords OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Previous Day Retransmitted Uncorrectable Codewords" ::= { zhoneVdslPerfDataEntry 42 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.43 zhoneVdslGinpLeftrSecs OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold." ::= { zhoneVdslPerfDataEntry 43 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.44 zhoneVdslGinpErrorFreeBits OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload). " ::= { zhoneVdslPerfDataEntry 44 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.45 zhoneVdslGinpMinEftr OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval." ::= { zhoneVdslPerfDataEntry 45 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.46 zhoneVdslGinpCurr15MinLeftrSecs OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold. This is the count for the current 15 minutes." ::= { zhoneVdslPerfDataEntry 46 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.47 zhoneVdslGinpCurr15MinErrorFreeBits OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload). This is the count for the current 15 minutes." ::= { zhoneVdslPerfDataEntry 47 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.48 zhoneVdslGinpCurr15MinMinEftr OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval. This is the count for the current 15 minutes." ::= { zhoneVdslPerfDataEntry 48 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.49 zhoneVdslGinpCurr1DayLeftrSecs OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold. This is the count for the current day." ::= { zhoneVdslPerfDataEntry 49 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.50 zhoneVdslGinpCurr1DayErrorFreeBits OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload). This is the count for the current day." ::= { zhoneVdslPerfDataEntry 50 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.51 zhoneVdslGinpCurr1DayMinEftr OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval. This is the count for the current day." ::= { zhoneVdslPerfDataEntry 51 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.52 zhoneVdslGinpPrev1DayLeftrSecs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LEFTRS - This counter counts the number of seconds that experienced a Low Error Free Throughput Rate (LEFTR), i,e., seconds during which the Error Free Throughput dropped below the configured threshold. This is the count for the previous day." ::= { zhoneVdslPerfDataEntry 52 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.53 zhoneVdslGinpPrev1DayErrorFreeBits OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "errorFreeBits - This counter counts the number of bits that crossed the alpha1/beta1 interface (bits available to carry user payload). This is the count for the previous day." ::= { zhoneVdslPerfDataEntry 53 } -- 1.3.6.1.4.1.5504.5.13.1.1.4.1.54 zhoneVdslGinpPrev1DayMinEftr OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "minEFTR - This performance monitoring parameter records the lowest value of Error Free Throughput during the current interval. This is the count for the previous day." ::= { zhoneVdslPerfDataEntry 54 } -- 1.3.6.1.4.1.5504.5.13.1.1.5 -- 1.3.6.1.4.1.5504.5.13.1.1.5 zhoneVdslPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu performance data collection interval. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97)." ::= { zhoneVdslMibObjects 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1 zhoneVdslPerfIntervalEntry OBJECT-TYPE SYNTAX ZhoneVdslPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPerfIntervalTable." INDEX { ifIndex, zhoneVdslPhysSide, zhoneVdslPerfIntervalNumber } ::= { zhoneVdslPerfIntervalTable 1 } ZhoneVdslPerfIntervalEntry ::= SEQUENCE { zhoneVdslPerfIntervalNumber Unsigned32, zhoneVdslPerfIntervalLofs HCPerfIntervalCount, zhoneVdslPerfIntervalLoss HCPerfIntervalCount, zhoneVdslPerfIntervalLprs HCPerfIntervalCount, zhoneVdslPerfIntervalLols HCPerfIntervalCount, zhoneVdslPerfIntervalESs HCPerfIntervalCount, zhoneVdslPerfIntervalSESs HCPerfIntervalCount, zhoneVdslPerfIntervalUASs HCPerfIntervalCount, zhoneVdslPerfIntervalInits HCPerfIntervalCount } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.1 zhoneVdslPerfIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional." ::= { zhoneVdslPerfIntervalEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.2 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.2 zhoneVdslPerfIntervalLofs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfIntervalEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.3 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.3 zhoneVdslPerfIntervalLoss OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfIntervalEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.4 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.4 zhoneVdslPerfIntervalLprs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfIntervalEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.5 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.5 zhoneVdslPerfIntervalLols OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link." ::= { zhoneVdslPerfIntervalEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.6 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.6 zhoneVdslPerfIntervalESs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) in the interval. An Errored Second is a one-second interval containing one or more CRC anomalies, one or more LOS or LOF defects." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfIntervalEntry 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.7 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.7 zhoneVdslPerfIntervalSESs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds in the interval." ::= { zhoneVdslPerfIntervalEntry 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.8 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.8 zhoneVdslPerfIntervalUASs OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds in the interval." ::= { zhoneVdslPerfIntervalEntry 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.9 -- 1.3.6.1.4.1.5504.5.13.1.1.5.1.9 zhoneVdslPerfIntervalInits OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during this interval. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerfIntervalEntry 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.6 -- 1.3.6.1.4.1.5504.5.13.1.1.6 zhoneVdslPerf1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent." ::= { zhoneVdslMibObjects 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1 zhoneVdslPerf1DayIntervalEntry OBJECT-TYPE SYNTAX ZhoneVdslPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslPerf1DayIntervalTable." INDEX { ifIndex, zhoneVdslPhysSide, zhoneVdslPerf1DayIntervalNumber } ::= { zhoneVdslPerf1DayIntervalTable 1 } ZhoneVdslPerf1DayIntervalEntry ::= SEQUENCE { zhoneVdslPerf1DayIntervalNumber Unsigned32, zhoneVdslPerf1DayIntervalMoniSecs HCPerfTimeElapsed, zhoneVdslPerf1DayIntervalLofs Unsigned32, zhoneVdslPerf1DayIntervalLoss Unsigned32, zhoneVdslPerf1DayIntervalLprs Unsigned32, zhoneVdslPerf1DayIntervalLols Unsigned32, zhoneVdslPerf1DayIntervalESs Unsigned32, zhoneVdslPerf1DayIntervalSESs Unsigned32, zhoneVdslPerf1DayIntervalUASs Unsigned32, zhoneVdslPerf1DayIntervalInits Unsigned32 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.1 zhoneVdslPerf1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..30) MAX-ACCESS not-accessible STATUS current DESCRIPTION "History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional." ::= { zhoneVdslPerf1DayIntervalEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.2 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.2 zhoneVdslPerf1DayIntervalMoniSecs OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { zhoneVdslPerf1DayIntervalEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.3 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.3 zhoneVdslPerf1DayIntervalLofs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Frame (LOF) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerf1DayIntervalEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.4 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.4 zhoneVdslPerf1DayIntervalLoss OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Signal (LOS) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerf1DayIntervalEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.5 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.5 zhoneVdslPerf1DayIntervalLprs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Power (LPR) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerf1DayIntervalEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.6 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.6 zhoneVdslPerf1DayIntervalLols OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Link (LOL) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." ::= { zhoneVdslPerf1DayIntervalEntry 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.7 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.7 zhoneVdslPerf1DayIntervalESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerf1DayIntervalEntry 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.8 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.8 zhoneVdslPerf1DayIntervalSESs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." ::= { zhoneVdslPerf1DayIntervalEntry 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.9 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.9 zhoneVdslPerf1DayIntervalUASs OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs." ::= { zhoneVdslPerf1DayIntervalEntry 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.10 -- 1.3.6.1.4.1.5504.5.13.1.1.6.1.10 zhoneVdslPerf1DayIntervalInits OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs. This count includes both successful and failed attempts." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslPerf1DayIntervalEntry 10 } -- 1.3.6.1.4.1.5504.5.13.1.1.7 -- 1.3.6.1.4.1.5504.5.13.1.1.7 zhoneVdslChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125)." ::= { zhoneVdslMibObjects 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1 -- 1.3.6.1.4.1.5504.5.13.1.1.7.1 zhoneVdslChanPerfDataEntry OBJECT-TYPE SYNTAX ZhoneVdslChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChanPerfDataTable." INDEX { ifIndex, zhoneVdslPhysSide } ::= { zhoneVdslChanPerfDataTable 1 } ZhoneVdslChanPerfDataEntry ::= SEQUENCE { zhoneVdslChanValidIntervals Integer32, zhoneVdslChanInvalidIntervals Integer32, zhoneVdslChanFixedOctets Integer32, zhoneVdslChanBadBlks Integer32, zhoneVdslChanCurr15MinTimeElapsed Integer32, zhoneVdslChanCurr15MinFixedOctets Integer32, zhoneVdslChanCurr15MinBadBlks Integer32, zhoneVdslChan1DayValidIntervals Integer32, zhoneVdslChan1DayInvalidIntervals Integer32, zhoneVdslChanCurr1DayTimeElapsed Integer32, zhoneVdslChanCurr1DayFixedOctets Integer32, zhoneVdslChanCurr1DayBadBlks Integer32 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.1 zhoneVdslChanValidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslChanPerfDataEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.2 zhoneVdslChanInvalidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) UNITS "intervals" MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslChanPerfDataEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.3 zhoneVdslChanFixedOctets OBJECT-TYPE SYNTAX Integer32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets since the unit was last reset." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanPerfDataEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.4 zhoneVdslChanBadBlks OBJECT-TYPE SYNTAX Integer32 UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks since the unit was last reset." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanPerfDataEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.5 zhoneVdslChanCurr15MinTimeElapsed OBJECT-TYPE SYNTAX Integer32 (0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { zhoneVdslChanPerfDataEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.6 zhoneVdslChanCurr15MinFixedOctets OBJECT-TYPE SYNTAX Integer32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanPerfDataEntry 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.7 zhoneVdslChanCurr15MinBadBlks OBJECT-TYPE SYNTAX Integer32 UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanPerfDataEntry 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.8 zhoneVdslChan1DayValidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslChanPerfDataEntry 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.9 zhoneVdslChan1DayInvalidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Invalid Intervals per definition found in HC-PerfHist-TC-MIB." ::= { zhoneVdslChanPerfDataEntry 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.10 zhoneVdslChanCurr1DayTimeElapsed OBJECT-TYPE SYNTAX Integer32 (0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { zhoneVdslChanPerfDataEntry 10 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.11 zhoneVdslChanCurr1DayFixedOctets OBJECT-TYPE SYNTAX Integer32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets since the beginning of the current 1-day interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanPerfDataEntry 11 } -- 1.3.6.1.4.1.5504.5.13.1.1.7.1.12 zhoneVdslChanCurr1DayBadBlks OBJECT-TYPE SYNTAX Integer32 UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks since the beginning of the current 1-day interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanPerfDataEntry 12 } -- 1.3.6.1.4.1.5504.5.13.1.1.8 -- 1.3.6.1.4.1.5504.5.13.1.1.8 zhoneVdslChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each Vtu channel data collection interval. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125)." ::= { zhoneVdslMibObjects 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.8.1 -- 1.3.6.1.4.1.5504.5.13.1.1.8.1 zhoneVdslChanIntervalEntry OBJECT-TYPE SYNTAX ZhoneVdslChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChanIntervalTable." INDEX { ifIndex, zhoneVdslPhysSide, zhoneVdslChanIntervalNumber } ::= { zhoneVdslChanIntervalTable 1 } ZhoneVdslChanIntervalEntry ::= SEQUENCE { zhoneVdslChanIntervalNumber Unsigned32, zhoneVdslChanIntervalFixedOctets HCPerfIntervalCount, zhoneVdslChanIntervalBadBlks HCPerfIntervalCount } -- 1.3.6.1.4.1.5504.5.13.1.1.8.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.8.1.1 zhoneVdslChanIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional." ::= { zhoneVdslChanIntervalEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.8.1.2 -- 1.3.6.1.4.1.5504.5.13.1.1.8.1.2 zhoneVdslChanIntervalFixedOctets OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanIntervalEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.8.1.3 -- 1.3.6.1.4.1.5504.5.13.1.1.8.1.3 zhoneVdslChanIntervalBadBlks OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChanIntervalEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.9 -- 1.3.6.1.4.1.5504.5.13.1.1.9 zhoneVdslChan1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslChan1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent." ::= { zhoneVdslMibObjects 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.9.1 -- 1.3.6.1.4.1.5504.5.13.1.1.9.1 zhoneVdslChan1DayIntervalEntry OBJECT-TYPE SYNTAX ZhoneVdslChan1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vdslChan1DayIntervalTable." INDEX { ifIndex, zhoneVdslPhysSide, zhoneVdslChan1DayIntervalNumber } ::= { zhoneVdslChan1DayIntervalTable 1 } ZhoneVdslChan1DayIntervalEntry ::= SEQUENCE { zhoneVdslChan1DayIntervalNumber Unsigned32, zhoneVdslChan1DayIntervalMoniSecs HCPerfTimeElapsed, zhoneVdslChan1DayIntervalFixedOctets HCPerfCurrentCount, zhoneVdslChan1DayIntervalBadBlks HCPerfCurrentCount } -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.1 zhoneVdslChan1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 (1..30) MAX-ACCESS not-accessible STATUS current DESCRIPTION "History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional." ::= { zhoneVdslChan1DayIntervalEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.2 -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.2 zhoneVdslChan1DayIntervalMoniSecs OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { zhoneVdslChan1DayIntervalEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.3 -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.3 zhoneVdslChan1DayIntervalFixedOctets OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of corrected octets in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChan1DayIntervalEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.4 -- 1.3.6.1.4.1.5504.5.13.1.1.9.1.4 zhoneVdslChan1DayIntervalBadBlks OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "blocks" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of uncorrectable blocks in this interval." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" ::= { zhoneVdslChan1DayIntervalEntry 4 } -- profile tables -- -- 1.3.6.1.4.1.5504.5.13.1.1.11 -- 1.3.6.1.4.1.5504.5.13.1.1.11 zhoneVdslLineConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. Entries in this table MUST be maintained in a persistent manner." ::= { zhoneVdslMibObjects 11 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1 zhoneVdslLineConfProfileEntry OBJECT-TYPE SYNTAX ZhoneVdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of a VDSL line. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document." INDEX { ifIndex } ::= { zhoneVdslLineConfProfileTable 1 } ZhoneVdslLineConfProfileEntry ::= SEQUENCE { zhoneVdslLineConfProfileName SnmpAdminString, zhoneVdslLineConfDownRateMode INTEGER, zhoneVdslLineConfUpRateMode INTEGER, zhoneVdslLineConfDownMaxPwr Integer32, zhoneVdslLineConfUpMaxPwr Integer32, zhoneVdslLineConfDownMaxSnrMgn Unsigned32, zhoneVdslLineConfDownMinSnrMgn Unsigned32, zhoneVdslLineConfDownTargetSnrMgn Unsigned32, zhoneVdslLineConfUpMaxSnrMgn Unsigned32, zhoneVdslLineConfUpMinSnrMgn Unsigned32, zhoneVdslLineConfUpTargetSnrMgn Unsigned32, zhoneVdslLineConfDownFastMaxDataRate Unsigned32, zhoneVdslLineConfDownFastMinDataRate Unsigned32, zhoneVdslLineConfDownSlowMaxDataRate Unsigned32, zhoneVdslLineConfDownSlowMinDataRate Unsigned32, zhoneVdslLineConfUpFastMaxDataRate Unsigned32, zhoneVdslLineConfUpFastMinDataRate Unsigned32, zhoneVdslLineConfUpSlowMaxDataRate Unsigned32, zhoneVdslLineConfUpSlowMinDataRate Unsigned32, zhoneVdslLineConfDownRateRatio Unsigned32, zhoneVdslLineConfUpRateRatio Unsigned32, zhoneVdslLineConfDownMaxInterDelay Unsigned32, zhoneVdslLineConfUpMaxInterDelay Unsigned32, zhoneVdslLineConfDownPboControl INTEGER, zhoneVdslLineConfUpPboControl INTEGER, zhoneVdslLineConfDownPboLevel Unsigned32, zhoneVdslLineConfUpPboLevel Unsigned32, zhoneVdslLineConfDeploymentScenario INTEGER, zhoneVdslLineConfAdslPresence INTEGER, zhoneVdslLineConfApplicableStandard INTEGER, zhoneVdslLineConfBandPlan INTEGER, zhoneVdslLineConfBandPlanFx Unsigned32, zhoneVdslLineConfBandOptUsage INTEGER, zhoneVdslLineConfUpPsdTemplate INTEGER, zhoneVdslLineConfDownPsdTemplate INTEGER, zhoneVdslLineConfHamBandMask BITS, zhoneVdslLineConfCustomNotch1Start Unsigned32, zhoneVdslLineConfCustomNotch1Stop Unsigned32, zhoneVdslLineConfCustomNotch2Start Unsigned32, zhoneVdslLineConfCustomNotch2Stop Unsigned32, zhoneVdslLineConfDownTargetSlowBurst Unsigned32, zhoneVdslLineConfUpTargetSlowBurst Unsigned32, zhoneVdslLineConfDownMaxFastFec Unsigned32, zhoneVdslLineConfUpMaxFastFec Unsigned32, zhoneVdslLineConfLineType INTEGER, zhoneVdslLineConfProfRowStatus RowStatus, zhoneVdslLineConfTransmissionMode INTEGER, zhoneVdslLineConfVdsl2Profile INTEGER, zhoneVdslLineConfVdslMode INTEGER, zhoneVdslLineConfPboElectricalOverride Integer32, zhoneVdslLineConfAutoModeCrtrn INTEGER, zhoneVdslLineConfNetworkTimingRef INTEGER, zhoneVdslLineConfAdslBandMode INTEGER, zhoneVdslLineConfAdslBandModeEndFreq Integer32, zhoneVdslLineConfSeltEchoMeasurementTime Integer32, zhoneVdslLineConfSeltNoiseMeasurementTime Integer32, zhoneVdslLineConfSeltAgc Integer32, zhoneVdslLineConfDownTrellis INTEGER, zhoneVdslLineConfUpTrellis INTEGER, zhoneVdslLineConfDownMaxAggregateTxPwr INTEGER, zhoneVdslLineConfUpMaxAggregateTxPwr INTEGER, zhoneVdslLineConfDownMaxPsd Integer32, zhoneVdslLineConfUpMaxPsd Integer32, zhoneVdslLineConfDownPsdShape INTEGER, zhoneVdslLineConfUpPsdShape INTEGER, zhoneVdslLineConfDownVirtualNoiseSnrMode INTEGER, zhoneVdslLineConfUpVirtualNoiseSnrMode INTEGER, zhoneVdslLineConfDownErasureDetectionFast INTEGER, zhoneVdslLineConfUpErasureDetectionFast INTEGER, zhoneVdslLineConfDownErasureDetectionInterleave INTEGER, zhoneVdslLineConfUpErasureDetectionInterleave INTEGER, zhoneVdslLineConfDownGhsA43TonePwr INTEGER, zhoneVdslLineConfDownGhsB43TonePwr INTEGER, zhoneVdslLineConfDownGhsA43cTonePwr INTEGER, zhoneVdslLineConfDownGhsV43TonePwr INTEGER, zhoneVdslLineConfDownGhsA43TonePwrMaxLvl Integer32, zhoneVdslLineConfDownGhsB43TonePwrMaxLvl Integer32, zhoneVdslLineConfDownGhsA43cTonePwrMaxLvl Integer32, zhoneVdslLineConfDownGhsV43TonePwrMaxLvl Integer32, zhoneVdslLineConfDownRsCoding INTEGER, zhoneVdslLineConfUpRsCoding INTEGER, zhoneVdslLineConfUpPboPsdTemplate INTEGER, zhoneVdslLineConfUpPboPsdParamA1 Integer32, zhoneVdslLineConfUpPboPsdParamA2 Integer32, zhoneVdslLineConfUpPboPsdParamB1 Integer32, zhoneVdslLineConfUpPboPsdParamB2 Integer32, zhoneVdslLineConfDownDownshiftSnrMgn Integer32, zhoneVdslLineConfDownUpshiftSnrMgn Integer32, zhoneVdslLineConfDownMinDownshiftTime Integer32, zhoneVdslLineConfDownMinUpshiftTime Integer32, zhoneVdslLineConfUpDownshiftSnrMgn Integer32, zhoneVdslLineConfUpUpshiftSnrMgn Integer32, zhoneVdslLineConfUpMinDownshiftTime Integer32, zhoneVdslLineConfUpMinUpshiftTime Integer32, zhoneVdslLineConfDownMinTxThresholdAlarm Unsigned32, zhoneVdslLineConfUpMinTxThresholdAlarm Unsigned32, zhoneVdslLineConfPotsBypassRelayMaxDuration INTEGER, zhoneVdslLineConfDMTConfMode INTEGER, zhoneVdslLineConfDownBitSwap INTEGER, zhoneVdslLineConfUpBitSwap INTEGER, zhoneVdslLineConfAdslAnnexMModeEnabled TruthValue, zhoneVdslLineConfAdslAnnexMPsdMask INTEGER, zhoneVdslLineConfUs0BoundaryTone INTEGER, zhoneVdslLineConfDownInp INTEGER, zhoneVdslLineConfUpInp INTEGER, zhoneVdslLineConfDownMaxInterleavingDelay INTEGER, zhoneVdslLineConfUpMaxInterleavingDelay INTEGER, zhoneVdslLineConfDownPsdMaskEnable INTEGER, zhoneVdslLineConfUpPsdMaskEnable INTEGER, zhoneVdslLineConfDownPsdMaskSelect INTEGER, zhoneVdslLineConfUpPsdMaskSelect INTEGER, zhoneVdslLineEnableTrellisCoding TruthValue, zhoneVdslLineEnableRsCoding TruthValue, zhoneVdslLineConfPsdShape INTEGER, zhoneVdslLineConfDownPhyRSupport INTEGER, zhoneVdslLineConfUpPhyRSupport INTEGER, zhoneVdslLineConfDownPhyRmaxINP INTEGER, zhoneVdslLineConfUpPhyRmaxINP INTEGER, zhoneVdslLineConfDownPhyRminRSoverhead INTEGER, zhoneVdslLineConfUpPhyRminRSoverhead INTEGER, zhoneVdslLineConfDownPhyRRtxRatio INTEGER, zhoneVdslLineConfUpPhyRRtxRatio INTEGER, zhoneVdslLineConfUpPboPsdParamA3 Integer32, zhoneVdslLineConfUpPboPsdParamA4 Integer32, zhoneVdslLineConfUpPboPsdParamB3 Integer32, zhoneVdslLineConfUpPboPsdParamB4 Integer32, zhoneVdslLineConfFallbackDefaultVpi Unsigned32, zhoneVdslLineConfFallbackDefaultVci Unsigned32, zhoneVdslLineConfDownGinpSupport INTEGER, zhoneVdslLineConfUpGinpSupport INTEGER, zhoneVdslLineConfDownGinpEtrMax Unsigned32, zhoneVdslLineConfUpGinpEtrMax Unsigned32, zhoneVdslLineConfDownGinpEtrMin Unsigned32, zhoneVdslLineConfUpGinpEtrMin Unsigned32, zhoneVdslLineConfDownGinpNdrMax Unsigned32, zhoneVdslLineConfUpGinpNdrMax Unsigned32, zhoneVdslLineConfDownGinpShineRatio Unsigned32, zhoneVdslLineConfUpGinpShineRatio Unsigned32, zhoneVdslLineConfDownGinpLeftrThreshold Unsigned32, zhoneVdslLineConfUpGinpLeftrThreshold Unsigned32, zhoneVdslLineConfDownGinpMaxDelay Unsigned32, zhoneVdslLineConfUpGinpMaxDelay Unsigned32, zhoneVdslLineConfDownGinpMinDelay Unsigned32, zhoneVdslLineConfUpGinpMinDelay Unsigned32, zhoneVdslLineConfDownGinpMin Unsigned32, zhoneVdslLineConfUpGinpMin Unsigned32, zhoneVdslLineConfDownGinpMinRSoverhead Unsigned32, zhoneVdslLineConfUpGinpMinRSoverhead Unsigned32, zhoneVdslLineConfDownGinpReinCfg Unsigned32, zhoneVdslLineConfUpGinpReinCfg Unsigned32, zhoneVdslLineConfDownGinpReinFreq INTEGER, zhoneVdslLineConfUpGinpReinFreq INTEGER, zhoneVdslLineConfDownGinpRtxMode INTEGER, zhoneVdslLineConfUpGinpRtxMode INTEGER } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.1 zhoneVdslLineConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies a row in this table. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document." ::= { zhoneVdslLineConfProfileEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.2 zhoneVdslLineConfDownRateMode OBJECT-TYPE SYNTAX INTEGER { manual(1), adapt-at-init(2), dynamic(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the rate selection behavior for the line in the downstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line at initialization only dynamic(3) adapts the line at initialization and showtime" DEFVAL { dynamic } ::= { zhoneVdslLineConfProfileEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.3 zhoneVdslLineConfUpRateMode OBJECT-TYPE SYNTAX INTEGER { manual(1), adapt-at-init(2), dynamic(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the rate selection behavior for the line in the upstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line at initialization only dynamic(3) adapts the line at initialization and showtime" DEFVAL { dynamic } ::= { zhoneVdslLineConfProfileEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.4 zhoneVdslLineConfDownMaxPwr OBJECT-TYPE SYNTAX Integer32 (-50..200) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum aggregate downstream power level in the range -5.0 to 20.0 dBm." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 145 } ::= { zhoneVdslLineConfProfileEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.5 zhoneVdslLineConfUpMaxPwr OBJECT-TYPE SYNTAX Integer32 (-130..200) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum aggregate upstream power level in the range -13.0 to 20.0 dBm." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 145 } ::= { zhoneVdslLineConfProfileEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.6 zhoneVdslLineConfDownMaxSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum downstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 160 } ::= { zhoneVdslLineConfProfileEntry 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.7 zhoneVdslLineConfDownMinSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum downstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.8 zhoneVdslLineConfDownTargetSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target downstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 24 } ::= { zhoneVdslLineConfProfileEntry 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.9 zhoneVdslLineConfUpMaxSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum upstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 160 } ::= { zhoneVdslLineConfProfileEntry 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.10 zhoneVdslLineConfUpMinSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum upstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 10 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.11 zhoneVdslLineConfUpTargetSnrMgn OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.10dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target upstream Signal/Noise Margin in units of 0.10 dB, for a range of 0 to 31.0 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { 24 } ::= { zhoneVdslLineConfProfileEntry 11 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.12 zhoneVdslLineConfDownFastMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum downstream fast channel data rate in steps of 1000 bits/second." DEFVAL { 200000 } ::= { zhoneVdslLineConfProfileEntry 12 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.13 zhoneVdslLineConfDownFastMinDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum downstream fast channel data rate in steps of 1000 bits/second." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 13 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.14 zhoneVdslLineConfDownSlowMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum downstream slow channel data rate in steps of 1000 bits/second. The maximum aggregate downstream transmit speed of the line can be derived from the sum of maximum downstream fast and slow channel data rates." DEFVAL { 200000 } ::= { zhoneVdslLineConfProfileEntry 14 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.15 zhoneVdslLineConfDownSlowMinDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum downstream slow channel data rate in steps of 1000 bits/second. The minimum aggregate downstream transmit speed of the line can be derived from the sum of minimum downstream fast and slow channel data rates." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 15 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.16 zhoneVdslLineConfUpFastMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum upstream fast channel data rate in steps of 1000 bits/second. The maximum aggregate upstream transmit speed of the line can be derived from the sum of maximum upstream fast and slow channel data rates." DEFVAL { 200000 } ::= { zhoneVdslLineConfProfileEntry 16 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.17 zhoneVdslLineConfUpFastMinDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum upstream fast channel data rate in steps of 1000 bits/second. The minimum aggregate upstream transmit speed of the line can be derived from the sum of minimum upstream fast and slow channel data rates." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 17 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.18 zhoneVdslLineConfUpSlowMaxDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum upstream slow channel data rate in steps of 1000 bits/second." DEFVAL { 200000 } ::= { zhoneVdslLineConfProfileEntry 18 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.19 zhoneVdslLineConfUpSlowMinDataRate OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minimum upstream slow channel data rate in steps of 1000 bits/second." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 19 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.20 zhoneVdslLineConfDownRateRatio OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents downstream Fast Channel Allocation / Slow Channel Allocation." DEFVAL { 50 } ::= { zhoneVdslLineConfProfileEntry 20 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.21 zhoneVdslLineConfUpRateRatio OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "For dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents upstream Fast Channel Allocation/Slow Channel Allocation." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 21 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.22 zhoneVdslLineConfDownMaxInterDelay OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum interleave delay for the downstream slow channel." DEFVAL { 80 } ::= { zhoneVdslLineConfProfileEntry 22 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.23 zhoneVdslLineConfUpMaxInterDelay OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum interleave delay for the upstream slow channel." DEFVAL { 80 } ::= { zhoneVdslLineConfProfileEntry 23 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.24 zhoneVdslLineConfDownPboControl OBJECT-TYPE SYNTAX INTEGER { disabled(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Downstream power backoff (PBO) control for this line. For transceivers which do not support downstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from zhoneVdslLineConfDownPboLevel." DEFVAL { disabled } ::= { zhoneVdslLineConfProfileEntry 24 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.25 zhoneVdslLineConfUpPboControl OBJECT-TYPE SYNTAX INTEGER { disabled(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff (PBO) control for this line. For transceivers which do not support upstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from zhoneVdslLineConfUpPboLevel." DEFVAL { disabled } ::= { zhoneVdslLineConfProfileEntry 25 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.26 zhoneVdslLineConfDownPboLevel OBJECT-TYPE SYNTAX Unsigned32 (0..160) UNITS "0.25dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the downstream backoff level to be used when vdslLineConfDownPboControl = manual(3)." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 26 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.27 zhoneVdslLineConfUpPboLevel OBJECT-TYPE SYNTAX Unsigned32 (0..160) UNITS "0.25dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the upstream backoff level to be used when vdslLineConfUpPboControl = manual(3)." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 27 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.28 zhoneVdslLineConfDeploymentScenario OBJECT-TYPE SYNTAX INTEGER { fttCab(1), fttEx(2), other(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VDSL line deployment scenario. When using fttCab(1), the VTU-C is located in a street cabinet. When using fttEx(2), the VTU-C is located at the central office. Changes to this value will have no effect on the transceiver." REFERENCE "DSL Forum TR-057" DEFVAL { fttCab } ::= { zhoneVdslLineConfProfileEntry 28 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.29 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.29 zhoneVdslLineConfAdslPresence OBJECT-TYPE SYNTAX INTEGER { none(1), adslOverPots(2), adslOverISDN(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates presence of ADSL service in the associated cable bundle/binder. none(1) indicates no ADSL service in the bundle adslOverPots(2) indicates ADSL service over POTS is present in the bundle adslOverISDN(3) indicates ADSL service over ISDN is present in the bundle" DEFVAL { none } ::= { zhoneVdslLineConfProfileEntry 29 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.30 zhoneVdslLineConfApplicableStandard OBJECT-TYPE SYNTAX INTEGER { ansi(1), etsi(2), itu(3), other(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VDSL standard to be used for the line. ansi(1) indicates ANSI standard etsi(2) indicates ETSI standard itu(3) indicates ITU standard other(4) indicates a standard other than the above." DEFVAL { ansi } ::= { zhoneVdslLineConfProfileEntry 30 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.31 zhoneVdslLineConfBandPlan OBJECT-TYPE SYNTAX INTEGER { bandPlan997(1), bandPlan998(2), bandPlanFx(3), other(4), bandPlan997-2(5), bandPlan997-3(6), bandPlan998-2(7), bandPlan998-3(8), bandPlan998-17-6(9), fx-2(10), fx-3(11), china-a-2(12), china-a-3(13), china-b-2(14), china-b-3(15) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VDSL band plan to be used for the line. bandPlan997(1) is to be used for ITU-T G.993.1 Bandplan-B ETSI Bandplan ANSI Plan 997 bandPlan998(2) is to be used for ITU-T G.993.1 Bandplan-A ANSI Plan 998 bandPlanFx(3) is to be used for ITU-T G.993.1 Bandplan-C. other(4) is to be used for non-standard bandplans. If this object is set to bandPlanFx(3), then the object vdslLineConfBandPlanFx MUST also be set." DEFVAL { bandPlan998 } ::= { zhoneVdslLineConfProfileEntry 31 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.32 zhoneVdslLineConfBandPlanFx OBJECT-TYPE SYNTAX Unsigned32 (3750..12000) UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "The frequency limit between bands D2 and U2 when zhoneVdslLineConfBandPlan is set to bandPlanFx(3)." DEFVAL { 3750 } ::= { zhoneVdslLineConfProfileEntry 32 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.33 zhoneVdslLineConfBandOptUsage OBJECT-TYPE SYNTAX INTEGER { unused(1), upstream(2), downstream(3), upstream-forced(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). unused(1) indicates Opt is unused upstream(2) indicates Opt usage is for upstream downstream(3) indicates Opt usage is for downstream. upstreamForced(4) indicates forced upstream" REFERENCE "ITU-T G.993.1, section 6.1" DEFVAL { upstream } ::= { zhoneVdslLineConfProfileEntry 33 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.34 zhoneVdslLineConfUpPsdTemplate OBJECT-TYPE SYNTAX INTEGER { ansi-fftex-m1(3), ansi-fftex-m2(4), ansi-fftcab-m1(5), fftcab-m2(6), etsi-m1(7), etsi-m2(8), psd-custom(9) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object has been modified by Zhone. The upstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard)." REFERENCE "DSL TR-057" DEFVAL { ansi-fftcab-m1 } ::= { zhoneVdslLineConfProfileEntry 34 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.35 zhoneVdslLineConfDownPsdTemplate OBJECT-TYPE SYNTAX INTEGER { ansi-fftex-m1(3), ansi-fftex-m2(4), ansi-fftcab-m1(5), fftcab-m2(6), fftcab-m1-adsl(7), fftcab-m1-adslplus(8), fftcab-m2-adsl(9), fftcab-m2-adslplus(10), etsi-pexp1-m1(11), etsi-pexp1-m2(12), etsi-pexp2-m1(13), etsi-pexp2-m2(14), psd-custom(15), etsi-pexm2-sample1(16), etsi-pexm2-sample2(17), etsi-pexm2-sample3(18), etsi-pexm2-sample4(19), etsi-pcab-m1(20), etsi-pcab-m2(21) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object has been modified by Zhone. The downstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard)." REFERENCE "DSL TR-057" DEFVAL { ansi-fftcab-m1 } ::= { zhoneVdslLineConfProfileEntry 35 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.36 zhoneVdslLineConfHamBandMask OBJECT-TYPE SYNTAX BITS { customNotch1(0), customNotch2(1), amateurBand30m(2), amateurBand40m(3), amateurBand80m(4), amateurBand160m(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The transmit power spectral density mask code, used to avoid interference with HAM (Handheld Amateur Radio) radio bands by introducing power control (notching) in one or more of these bands. Amateur radio band notching is defined in the VDSL spectrum as follows: Band Start Frequency Stop Frequency ---- ------------------ -------------------------------- 30m 1810 kHz 2000 kHz 40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI) 80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI) 160m 10100 kHz 10150 kHz Notching for each standard band can be enabled or disabled via the bit mask. Two custom notches may be specified. If either of these are enabled via the bit mask, then the following objects MUST be specified: If customNotch1 is enabled, then both zhoneVdslLineConfCustomNotch1Start zhoneVdslLineConfCustomNotch1Stop MUST be specified. If customNotch2 is enabled, then both zhoneVdslLineConfCustomNotch2Start zhoneVdslLineConfCustomNotch2Stop MUST be specified." REFERENCE "DSLF TR-057, section 2.6" ::= { zhoneVdslLineConfProfileEntry 36 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.37 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.37 zhoneVdslLineConfCustomNotch1Start OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 1. zhoneVdslLineConfCustomNotch1Start MUST be less than or equal to vdslLineConfCustomNotch1Stop." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 37 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.38 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.38 zhoneVdslLineConfCustomNotch1Stop OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 1. zhoneVdslLineConfCustomNotch1Stop MUST be greater than or equal to vdslLineConfCustomNotch1Start." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 38 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.39 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.39 zhoneVdslLineConfCustomNotch2Start OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch 2. zhoneVdslLineConfCustomNotch2Start MUST be less than or equal to vdslLineConfCustomNotch2Stop." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 39 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.40 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.40 zhoneVdslLineConfCustomNotch2Stop OBJECT-TYPE SYNTAX Unsigned32 UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 2. zhoneVdslLineConfCustomNotch2Stop MUST be greater than or equal to vdslLineConfCustomNotch2Start." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 40 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.41 zhoneVdslLineConfDownTargetSlowBurst OBJECT-TYPE SYNTAX Unsigned32 (0..1275) UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel." REFERENCE "ITU-T G.997.1, section 7.3.2.3" DEFVAL { 5 } ::= { zhoneVdslLineConfProfileEntry 41 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.42 zhoneVdslLineConfUpTargetSlowBurst OBJECT-TYPE SYNTAX Unsigned32 (0..1275) UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the target level of impulse noise (burst) protection for an interleaved (slow) channel." REFERENCE "ITU-T G.997.1, section 7.3.2.3" DEFVAL { 5 } ::= { zhoneVdslLineConfProfileEntry 42 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.43 zhoneVdslLineConfDownMaxFastFec OBJECT-TYPE SYNTAX Unsigned32 (0..50) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 43 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.44 zhoneVdslLineConfUpMaxFastFec OBJECT-TYPE SYNTAX Unsigned32 (0..50) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 44 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.45 zhoneVdslLineConfLineType OBJECT-TYPE SYNTAX INTEGER { noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter provisions the VDSL physical entity at start-up by defining whether and how the line will be channelized, i.e., which channel type(s) are supported. If the line is to be channelized, the value will be other than noChannel(1). This configuration can be activated only during start-up. Afterwards, the value of zhoneVdslLineType coincides with the value of zhoneVdslLineConfLineType. Depending on this value, the corresponding entries in the ifTable for the interleaved and the fast channels are enabled or disabled according to the value of their ifOperStatus. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exists, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel." REFERENCE "T1E1.4/2000-009R3, Part 1, common spec" DEFVAL { fastOnly } ::= { zhoneVdslLineConfProfileEntry 45 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.46 -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.47 zhoneVdslLineConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time. Note that some changes may require that any referenced lines be restarted (e.g., zhoneVdslLineConfLineType)." ::= { zhoneVdslLineConfProfileEntry 47 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.48 zhoneVdslLineConfTransmissionMode OBJECT-TYPE SYNTAX INTEGER { autoNegotiateMode(1), vdslMode(2), vdsl2Mode(3), adsl2PlusMode(4), adsl2Mode(5), gdmtMode(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "The transmission standard to be used for the line." DEFVAL { autoNegotiateMode } ::= { zhoneVdslLineConfProfileEntry 48 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.49 zhoneVdslLineConfVdsl2Profile OBJECT-TYPE SYNTAX INTEGER { g993-2-8a(1), g993-2-8b(2), g993-2-8c(3), g993-2-8d(4), g993-2-12a(5), g993-2-12b(6), g993-2-17a(7), g993-2-30a(8) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VDSL2 standard to be used for the line." DEFVAL { g993-2-12a } ::= { zhoneVdslLineConfProfileEntry 49 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.50 zhoneVdslLineConfVdslMode OBJECT-TYPE SYNTAX INTEGER { standard(1), long-reach-8k(2), r8k(3), std-8k(4), lr-8k(5), std-lr(6), std-lr-8k(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "Controls which VDSL modes are available on the line." DEFVAL { standard } ::= { zhoneVdslLineConfProfileEntry 50 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.51 zhoneVdslLineConfPboElectricalOverride OBJECT-TYPE SYNTAX Integer32 (0..256) UNITS ".5 dBm/Mhz" MAX-ACCESS read-create STATUS current DESCRIPTION "Override electrical length estimated by VUTU_C. The special value 256 means do not perform override." DEFVAL { 256 } ::= { zhoneVdslLineConfProfileEntry 51 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.52 zhoneVdslLineConfAutoModeCrtrn OBJECT-TYPE SYNTAX INTEGER { crtrn-chip-prop(1), optimize-us(2), optimize-ds(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the policy to select optimal mode of oepration." DEFVAL { optimize-us } ::= { zhoneVdslLineConfProfileEntry 52 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.53 zhoneVdslLineConfNetworkTimingRef OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable reference clock source." DEFVAL { disable } ::= { zhoneVdslLineConfProfileEntry 53 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.54 zhoneVdslLineConfAdslBandMode OBJECT-TYPE SYNTAX INTEGER { allowed(1), not-allowed(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the XDSL can use the ADSL spectrum or not." DEFVAL { allowed } ::= { zhoneVdslLineConfProfileEntry 54 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.55 zhoneVdslLineConfAdslBandModeEndFreq OBJECT-TYPE SYNTAX Integer32 (276..2208) UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the ADSL band end frequency when the ADSL band usage is not allowed." DEFVAL { 1104 } ::= { zhoneVdslLineConfProfileEntry 55 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.56 zhoneVdslLineConfSeltEchoMeasurementTime OBJECT-TYPE SYNTAX Integer32 (5..240) UNITS "secs" MAX-ACCESS read-create STATUS current DESCRIPTION "Contains the SELT echo measurement time" DEFVAL { 50 } ::= { zhoneVdslLineConfProfileEntry 56 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.57 zhoneVdslLineConfSeltNoiseMeasurementTime OBJECT-TYPE SYNTAX Integer32 (5..240) UNITS "secs" MAX-ACCESS read-create STATUS current DESCRIPTION "Contains the SELT noise measurement time." DEFVAL { 50 } ::= { zhoneVdslLineConfProfileEntry 57 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.58 zhoneVdslLineConfSeltAgc OBJECT-TYPE SYNTAX Integer32 (-100..100) UNITS "1 dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Contains the SELT AGC gain value." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 58 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.59 zhoneVdslLineConfDownTrellis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enables/disables downstream Trellis coding." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 59 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.60 zhoneVdslLineConfUpTrellis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enables/disables upstream Trellis coding." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 60 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.61 zhoneVdslLineConfDownMaxAggregateTxPwr OBJECT-TYPE SYNTAX INTEGER { unlimited(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum total power that is allowed to be transmitted in the downstream direction." DEFVAL { unlimited } ::= { zhoneVdslLineConfProfileEntry 61 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.62 zhoneVdslLineConfUpMaxAggregateTxPwr OBJECT-TYPE SYNTAX INTEGER { unlimited(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum total power that is allowed to be transmitted in the upstream direction." DEFVAL { unlimited } ::= { zhoneVdslLineConfProfileEntry 62 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.63 zhoneVdslLineConfDownMaxPsd OBJECT-TYPE SYNTAX Integer32 (-955..0) UNITS ".1 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum power spectral density level allowed on the line at the transmitter output downstream for initialization and showtime signals." DEFVAL { -1 } ::= { zhoneVdslLineConfProfileEntry 63 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.64 zhoneVdslLineConfUpMaxPsd OBJECT-TYPE SYNTAX Integer32 (-955..0) UNITS ".1 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum power spectral density level allowed on the line at the transmitter output upstream for initialization and showtime signals." DEFVAL { -1 } ::= { zhoneVdslLineConfProfileEntry 64 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.65 zhoneVdslLineConfDownPsdShape OBJECT-TYPE SYNTAX INTEGER { custom-psd(1), region-a-psd(2), region-c-psd(3), region-b-m1-a-psd(4), region-b-m1-b-psd(5), region-b-m1-us0-psd(6), region-b-m2-a-psd(7), region-b-m2-m-psd(8), region-b-m2-b-psd(9), region-b-m2-us0-psd(10) } MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum transmit PSD allowed in the downstream channel on a VDSL2 line." DEFVAL { region-a-psd } ::= { zhoneVdslLineConfProfileEntry 65 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.66 zhoneVdslLineConfUpPsdShape OBJECT-TYPE SYNTAX INTEGER { custom-psd(1), region-a-psd(2), region-c-psd(3), region-b-m1-a-psd(4), region-b-m1-b-psd(5), region-b-m1-us0-psd(6), region-b-m2-a-psd(7), region-b-m2-m-psd(8), region-b-m2-b-psd(9), region-b-m2-us0-psd(10) } MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum transmit PSD allowed in the upstream channel on a VDSL2 line." DEFVAL { region-a-psd } ::= { zhoneVdslLineConfProfileEntry 66 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.67 zhoneVdslLineConfDownVirtualNoiseSnrMode OBJECT-TYPE SYNTAX INTEGER { mode1(1), mode2(2), mode3(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Downstream virtual noise SNR mode on a VDSL2 line." DEFVAL { mode1 } ::= { zhoneVdslLineConfProfileEntry 67 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.68 zhoneVdslLineConfUpVirtualNoiseSnrMode OBJECT-TYPE SYNTAX INTEGER { mode1(1), mode2(2), mode3(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream virtual noise SNR mode on a VDSL2 line." DEFVAL { mode1 } ::= { zhoneVdslLineConfProfileEntry 68 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.69 zhoneVdslLineConfDownErasureDetectionFast OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the erasure detection mechanism should be enabled or disabled in the downstream fast channel." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 69 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.70 zhoneVdslLineConfUpErasureDetectionFast OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the erasure detection mechanism should be enabled or disabled in the downstream fast channel." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 70 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.71 zhoneVdslLineConfDownErasureDetectionInterleave OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the erasure detection mechanism should be enabled or disabled in the downstream slow channel (interleave)." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 71 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.72 zhoneVdslLineConfUpErasureDetectionInterleave OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the erasure detection mechanism should be enabled or disabled in the uptream slow channel (interleave)." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 72 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.73 zhoneVdslLineConfDownGhsA43TonePwr OBJECT-TYPE SYNTAX INTEGER { default(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the mode of the downstream tones power used during handshake, during A43 mode." DEFVAL { default } ::= { zhoneVdslLineConfProfileEntry 73 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.74 zhoneVdslLineConfDownGhsB43TonePwr OBJECT-TYPE SYNTAX INTEGER { default(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the mode of the downstream tones power used during handshake, during B43 mode." DEFVAL { default } ::= { zhoneVdslLineConfProfileEntry 74 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.75 zhoneVdslLineConfDownGhsA43cTonePwr OBJECT-TYPE SYNTAX INTEGER { default(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the mode of the downstream tones power used during handshake, during A43c mode." DEFVAL { default } ::= { zhoneVdslLineConfProfileEntry 75 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.76 zhoneVdslLineConfDownGhsV43TonePwr OBJECT-TYPE SYNTAX INTEGER { default(1), auto(2), manual(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the mode of the downstream tone power used during handshake, during V43 mode." DEFVAL { default } ::= { zhoneVdslLineConfProfileEntry 76 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.77 zhoneVdslLineConfDownGhsA43TonePwrMaxLvl OBJECT-TYPE SYNTAX Integer32 (-99..-40) UNITS "0.5 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the maximum power of downstream tones used, in manual mode, during handshake in A43 mode. A value of -99 indicates no power used." DEFVAL { -99 } ::= { zhoneVdslLineConfProfileEntry 77 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.78 zhoneVdslLineConfDownGhsB43TonePwrMaxLvl OBJECT-TYPE SYNTAX Integer32 (-99..-40) UNITS "0.5 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the maximum power of downstream tones used, in manual mode, during handshake in B43 mode. A value of -99 indicates no power used." DEFVAL { -99 } ::= { zhoneVdslLineConfProfileEntry 78 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.79 zhoneVdslLineConfDownGhsA43cTonePwrMaxLvl OBJECT-TYPE SYNTAX Integer32 (-99..-40) UNITS "0.5 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the maximum power of downstream tones used, in manual mode, during handshake in A43c mode. A value of -99 indicates no power used." DEFVAL { -99 } ::= { zhoneVdslLineConfProfileEntry 79 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.80 zhoneVdslLineConfDownGhsV43TonePwrMaxLvl OBJECT-TYPE SYNTAX Integer32 (-99..-40) UNITS "0.5 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Determines the maximum power of downstream tones used, in manual mode, during handshake in V43 mode. A value of -99 indicates no power used." DEFVAL { -99 } ::= { zhoneVdslLineConfProfileEntry 80 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.81 zhoneVdslLineConfDownRsCoding OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter to enable/disable RS Coding in downstream channel." DEFVAL { disable } ::= { zhoneVdslLineConfProfileEntry 81 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.82 zhoneVdslLineConfUpRsCoding OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Parameter to enable/disable RS Coding in upsream channel." DEFVAL { disable } ::= { zhoneVdslLineConfProfileEntry 82 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.83 zhoneVdslLineConfUpPboPsdTemplate OBJECT-TYPE SYNTAX INTEGER { ansi-a(1), ansi-f(2), etsi-a(3), etsi-b(4), etsi-c(5), etsi-d(6), etsi-e(7), etsi-f(8), custom(9), ab-param(10) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum received PSD allowed in the upstream channel on the VDSLx line." DEFVAL { ansi-a } ::= { zhoneVdslLineConfProfileEntry 83 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.84 zhoneVdslLineConfUpPboPsdParamA1 OBJECT-TYPE SYNTAX Integer32 (4000..8589) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter A1. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 84 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.85 zhoneVdslLineConfUpPboPsdParamA2 OBJECT-TYPE SYNTAX Integer32 (4000..8589) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter A2. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 85 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.86 zhoneVdslLineConfUpPboPsdParamB1 OBJECT-TYPE SYNTAX Integer32 (0..8589) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter B1. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 86 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.87 zhoneVdslLineConfUpPboPsdParamB2 OBJECT-TYPE SYNTAX Integer32 (0..8589) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter B2. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 87 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.88 zhoneVdslLineConfDownDownshiftSnrMgn OBJECT-TYPE SYNTAX Integer32 (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate." DEFVAL { 30 } ::= { zhoneVdslLineConfProfileEntry 88 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.89 zhoneVdslLineConfDownUpshiftSnrMgn OBJECT-TYPE SYNTAX Integer32 (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate." DEFVAL { 90 } ::= { zhoneVdslLineConfProfileEntry 89 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.90 zhoneVdslLineConfDownMinDownshiftTime OBJECT-TYPE SYNTAX Integer32 (0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs." DEFVAL { 30 } ::= { zhoneVdslLineConfProfileEntry 90 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.91 zhoneVdslLineConfDownMinUpshiftTime OBJECT-TYPE SYNTAX Integer32 (0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs." DEFVAL { 30 } ::= { zhoneVdslLineConfProfileEntry 91 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.92 zhoneVdslLineConfUpDownshiftSnrMgn OBJECT-TYPE SYNTAX Integer32 (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate." DEFVAL { 30 } ::= { zhoneVdslLineConfProfileEntry 92 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.93 zhoneVdslLineConfUpUpshiftSnrMgn OBJECT-TYPE SYNTAX Integer32 (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate." DEFVAL { 90 } ::= { zhoneVdslLineConfProfileEntry 93 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.94 zhoneVdslLineConfUpMinDownshiftTime OBJECT-TYPE SYNTAX Integer32 (0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs." DEFVAL { 30 } ::= { zhoneVdslLineConfProfileEntry 94 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.95 zhoneVdslLineConfUpMinUpshiftTime OBJECT-TYPE SYNTAX Integer32 (0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs." DEFVAL { 30 } ::= { zhoneVdslLineConfProfileEntry 95 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.96 zhoneVdslLineConfDownMinTxThresholdAlarm OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum CO Tx Sync rate threshold alarm. If set to 0, this field is disregarded. Otherwise, if Tx Sync rate falls below this value, a trap and alarm will be issued" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 96 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.97 zhoneVdslLineConfUpMinTxThresholdAlarm OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum CPE Tx Sync rate threshold alarm. If set to 0, this field is disregarded. Otherwise, if Tx Sync rate falls below this value, a trap and alarm will be issued" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 97 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.98 zhoneVdslLineConfPotsBypassRelayMaxDuration OBJECT-TYPE SYNTAX INTEGER (1..300) UNITS "secs" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum duration in seconds that an Adsl Pots Low Pass Filter Bypass Relay will remain active (meaning closed/energized). As a fail-safe mechanism, the relay will automatically return a line back to normal operational mode when this timer has expired. This object is only valid for Adsl Pots Splitter cards containing the Pots LPF Bypass Relays." DEFVAL { 60 } ::= { zhoneVdslLineConfProfileEntry 98 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.99 zhoneVdslLineConfDMTConfMode OBJECT-TYPE SYNTAX INTEGER { echocancel(1), freqdivmux(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Discrete Multi-Tone parameter that selects whether there is overlap (echoCancel) or no overlap (freqDivMux) of bins." DEFVAL { freqdivmux } ::= { zhoneVdslLineConfProfileEntry 99 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.100 zhoneVdslLineConfDownBitSwap OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable downstream bit swap." DEFVAL { enabled } ::= { zhoneVdslLineConfProfileEntry 100 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.101 zhoneVdslLineConfUpBitSwap OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable upstream bit swap." DEFVAL { enabled } ::= { zhoneVdslLineConfProfileEntry 101 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.102 zhoneVdslLineConfAdslAnnexMModeEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether Annex-M mode is enabled on the Adsl modem. If this object is set to 'true' then Annex-M mode is enabled. If it is set to 'false then Annex-M mode is disabled." DEFVAL { false } ::= { zhoneVdslLineConfProfileEntry 102 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.103 zhoneVdslLineConfAdslAnnexMPsdMask OBJECT-TYPE SYNTAX INTEGER { eu64(1), eu60(2), eu56(3), eu52(4), eu48(5), eu44(6), eu40(7), eu36(8), eu32(9), all(10) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the maximum transmit PSD allowed in the downstream channel on an BIS Annex-M line." DEFVAL { eu32 } ::= { zhoneVdslLineConfProfileEntry 103 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.104 zhoneVdslLineConfUs0BoundaryTone OBJECT-TYPE SYNTAX INTEGER { d32(1), d36(2), d40(3), d44(4), d48(5), d52(6), d56(7), d64(8) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the upper boundary of US0. US0 is used in long reach mode when there is no more capacity in US1. The switchover is typically around 3500 feet." DEFVAL { d32 } ::= { zhoneVdslLineConfProfileEntry 104 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.105 zhoneVdslLineConfDownInp OBJECT-TYPE SYNTAX INTEGER { noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteenSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) } MAX-ACCESS read-create STATUS current DESCRIPTION "The minimum impulse noise protection for the downstream bearer channel expressed in symbols. One symbol equals 250 uS." DEFVAL { twoSymbols } ::= { zhoneVdslLineConfProfileEntry 105 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.106 zhoneVdslLineConfUpInp OBJECT-TYPE SYNTAX INTEGER { noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), fourSymbols(5), eightSymbols(6), sixteenSymbols(7), threeSymbols(8), fiveSymbols(9), sixSymbols(10), sevenSymbols(11), nineSymbols(12), tenSymbols(13), elevenSymbols(14), twelveSymbols(15), thirteenSymbols(16), fourteenSymbols(17), fifteenSymbols(18) } MAX-ACCESS read-create STATUS current DESCRIPTION "The minimum impulse noise protection for the upstream bearer channel expressed in symbols. One symbol equals 250 uS." DEFVAL { twoSymbols } ::= { zhoneVdslLineConfProfileEntry 106 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.107 zhoneVdslLineConfDownMaxInterleavingDelay OBJECT-TYPE SYNTAX INTEGER (0..63) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum inteleaving delay in the downstream direction. A value of zero indicates no delay introduced." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 107 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.108 zhoneVdslLineConfUpMaxInterleavingDelay OBJECT-TYPE SYNTAX INTEGER (0..63) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum inteleaving delay in the upstream direction. A value of zero indicates no delay introduced." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 108 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.109 zhoneVdslLineConfDownPsdMaskEnable OBJECT-TYPE SYNTAX INTEGER { standard(2), mod(3), modFallback(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object selects the Psd Mask in the downstream direction. 'standard' : use the PSD Mask specified in the object zhoneVdslLineConfDownPsdSelect 'mod' : use the pre-defined Mask-On-Demand PSD Mask 'modFallback': use the pre-defined Mask-On-Demand PSD Mask with fallback" DEFVAL { standard } ::= { zhoneVdslLineConfProfileEntry 109 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.110 zhoneVdslLineConfUpPsdMaskEnable OBJECT-TYPE SYNTAX INTEGER { standard(2), mod(3), modFallback(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object selects the Psd Mask in the upstream direction. 'standard' : use the PSD Mask specified in the object zhoneVdslLineConfDownPsdSelect 'mod' : use the pre-defined Mask-On-Demand PSD Mask 'modFallback': use the pre-defined Mask-On-Demand PSD Mask with fallback" DEFVAL { standard } ::= { zhoneVdslLineConfProfileEntry 110 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.111 zhoneVdslLineConfDownPsdMaskSelect OBJECT-TYPE SYNTAX INTEGER { custom(1), customMOD(2), dmtPSDCOMSK2(3), dmtPSDFLATMSK(4), dmtPSDCABMSK2(5), dmtPSDCOMSK2RFI(6), dmtPSDFLATMSKRFI(7), dmtPSDCABMSK2RFI(8), dmtPSDADSL2NONOVLPM1(9), dmtPSDADSL2NONOVLPM2(10), dmtPSDADSL2NONOVLPFLAT(11), g993RegionC(12), g993RegionA(13), g993RegionA-E17a-D-32(14), g993RegionA-E17a-D-48(15), g993RegionA-E17a-D-64(16), g993RegionA-E17a-D-128(17), g998RegionB-M1x-A(18), g998RegionB-M1x-B(19), g998RegionB-M1x-NUS0(20), g998RegionB-M2x-A(21), g998RegionB-M2x-M(22), g998RegionB-M2x-B(23), g998RegionB-M2x-NUS0(24), g998RegionB-E17-M2x-NUS0(25), g998RegionB-E17-M2x-NUS0-M(26), g998RegionB-ADE17-M2x-NUS0-M(27), g998RegionB-ADE17-M2x-A(28), g998RegionB-ADE17-M2x-B(29), g998RegionB-E30-M2x-NUS0(30), g998RegionB-E30-M2x-NUS0-M(31), g998RegionB-ADE30-M2x-NUS0-M(32), g998RegionB-ADE30-M2x-NUS0-A(33), g998RegionB-NONSTD-E17-M2x(34), g998RegionB-NONSTD-E17-M2x-M(35), g997RegionB-M1c-A-7(36), g997RegionB-M1x-M-8(37), g997RegionB-M1x-M(38), g997RegionB-M2x-M-8(39), g997RegionB-M2x-A(40), g997RegionB-M2x-M(41), g997RegionB-HPE17-M1-NUS0(42), g997RegionB-HPE30-M1-NUS0(43), g997RegionB-E17-M2x-A(44), g997RegionB-E30-M2x-NUS0(45) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object selects one of the standards based PSD mask for the downstream direction. The object zhoneVdslLineConfDownPsdMaskEnable must be set to 'standard' for this object to be active." DEFVAL { g993RegionA } ::= { zhoneVdslLineConfProfileEntry 111 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.112 zhoneVdslLineConfUpPsdMaskSelect OBJECT-TYPE SYNTAX INTEGER { custom(1), g993J-ADLU-32(2), g993J-ADLU-36(3), g993J-ADLU-40(4), g993J-ADLU-44(5), g993J-ADLU-48(6), g993J-ADLU-52(7), g993J-ADLU-60(8), g993J-ADLU-64(9), g993JM-EU-32(10), g993JM-EU-36(11), g993JM-EU-40(12), g993JM-EU-44(13), g993JM-EU-48(14), g993JM-EU-52(15), g993JM-EU-60(16), g993JM-EU-64(17), dmtExtended(18), dmtJJ100(19), dmtStandard(20), g993RegionA-EU-32(21), g993RegionA-EU-36(22), g993RegionA-EU-40(23), g993RegionA-EU-44(24), g993RegionA-EU-48(25), g993RegionA-EU-52(26), g993RegionA-EU-56(27), g993RegionA-EU-60(28), g993RegionA-EU-64(29), g998RegionB-M1x-A(30), g998RegionB-M1x-B(31), g998RegionB-M1x-NUS0(32), g998RegionB-M2x-A(33), g998RegionB-M2x-M(34), g998RegionB-M2x-B(35), g998RegionB-M2x-NUS0(36), g998RegionB-E17-M2x-NUS0(37), g998RegionB-E17-M2x-NUS0-M(38), g998RegionB-ADE17-M2x-NUS0-M(39), g998RegionB-ADE17-M2x-A(40), g998RegionB-ADE17-M2x-B(41), g998RegionB-E30-M2x-NUS0(42), g998RegionB-E30-M2x-NUS0-M(43), g998RegionB-ADE30-M2x-NUS0-M(44), g998RegionB-ADE30-M2x-NUS0-A(45), g998RegionB-NONSTD-E17-M2x(46), g998RegionB-NONSTD-E17-M2x-M(47), g997RegionB-M1c-A-7(48), g997RegionB-M1x-M-8(49), g997RegionB-M1x-M(50), g997RegionB-M2x-M-8(51), g997RegionB-M2x-A(52), g997RegionB-M2x-M(53), g997RegionB-HPE17-M1-NUS0(54), g997RegionB-HPE30-M1-NUS0(55), g997RegionB-E17-M2x-A(56), g997RegionB-E30-M2x-NUS0(57) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object selects one of the standards based PSD mask for the upstream direction. The object zhoneVdslLineConfUpPsdMaskEnable must be set to 'standard' for this object to be active." DEFVAL { g993RegionA-EU-32 } ::= { zhoneVdslLineConfProfileEntry 112 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.113 zhoneVdslLineEnableTrellisCoding OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Enables/disables Trellis coding." DEFVAL { true } ::= { zhoneVdslLineConfProfileEntry 113 } -- -- -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.114 zhoneVdslLineEnableRsCoding OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Enables/disables Rs coding." DEFVAL { true } ::= { zhoneVdslLineConfProfileEntry 114 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.115 zhoneVdslLineConfPsdShape OBJECT-TYPE SYNTAX INTEGER { region-a-nus0(1), region-a-eu-32(2), region-a-eu-36(3), region-a-eu-40(4), region-a-eu-44(5), region-a-eu-48(6), region-a-eu-52(7), region-a-eu-56(8), region-a-eu-60(9), region-a-eu-64(10), region-a-eu-128(11), region-a-adlu-32(12), region-a-adlu-36(13), region-a-adlu-40(14), region-a-adlu-44(15), region-a-adlu-48(16), region-a-adlu-52(17), region-a-adlu-56(18), region-a-adlu-60(19), region-a-adlu-64(20), region-a-adlu-128(21), region-b-998-m1x-a(22), region-b-998-m1x-b(23), region-b-998-m1x-nus0(24), region-b-998-m2x-a(25), region-b-998-m2x-m(26), region-b-998-m2x-b(27), region-b-998-m2x-nus0(28), region-b-998-e17-m2x-nus0(29), region-b-998-e17-m2x-nus0-m(30), region-b-998-ade17-m2x-nus0-m(31), region-b-998-ade17-m2x-a(32), region-b-998-ade17-m2x-b(33), region-b-998-e30-m2x-nus0(34), region-b-998-e30-m2x-nus0-m(35), region-b-998-ade30-m2x-nus0-m(36), region-b-998-ade30-m2x-nus0-a(37), region-b-997-m1c-a-7(38), region-b-997-m1x-m-8(39), region-b-997-m1x-m(40), region-b-997-m2x-m-8(41), region-b-997-m2x-a(42), region-b-997-m2x-m(43), region-b-997-hpe17-m1-nus0(44), region-b-997-hpe30-m1-nus0(45), region-b-997-e17-m2x-a(46), region-b-997-e30-m2x-nus0(47), region-b-997-bt-anfp(48), region-c-138-b(49), region-c-276-b(50), region-c-138-co(51), region-c-276-co(52), region-c-tcmisdn(53), region-c-1104-co-17a(54), region-c-1104-co-30a(55) } MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum transmit PSD allowed on a VDSL2 line." DEFVAL { region-a-eu-32 } ::= { zhoneVdslLineConfProfileEntry 115 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.116 zhoneVdslLineConfDownPhyRSupport OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable downstream PHYR. Only supported by Broadcom PHYR ports." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 116 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.117 zhoneVdslLineConfUpPhyRSupport OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable upstream PHYR. Only supported by Broadcom PHYR ports." DEFVAL { enable } ::= { zhoneVdslLineConfProfileEntry 117 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.118 zhoneVdslLineConfDownPhyRmaxINP OBJECT-TYPE SYNTAX INTEGER (0 | 5..160) MAX-ACCESS read-create STATUS current DESCRIPTION "PHYR maximum downstream impulse noise protection. A value of 0 specifies no protection. The values 5 through 160 specify the number of symbols in 1/10 increments. Only supported by Broadcom PHYR ports." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 118 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.119 zhoneVdslLineConfUpPhyRmaxINP OBJECT-TYPE SYNTAX INTEGER (0 | 5..160) MAX-ACCESS read-create STATUS current DESCRIPTION "PHYR maximum upstream impulse noise protection. A value of 0 specifies no protection. The values 5 through 160 specify the number of symbols in 1/10 increments. Only supported by Broadcom PHYR ports." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 119 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.120 zhoneVdslLineConfDownPhyRminRSoverhead OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "PHYR minimum downstream RS overhead. Only supported by Broadcom PHYR ports." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 120 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.121 zhoneVdslLineConfUpPhyRminRSoverhead OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "PHYR minimum upstream RS overhead. Only supported by Broadcom PHYR ports." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 121 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.122 zhoneVdslLineConfDownPhyRRtxRatio OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "PHYR minimum downstream fraction of the line rate allocated for retransmission. Only supported by Broadcom PHYR ports." ::= { zhoneVdslLineConfProfileEntry 122 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.123 zhoneVdslLineConfUpPhyRRtxRatio OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "PHYR minimum upstream fraction of the line rate allocated for retransmission. Only supported by Broadcom PHYR ports." DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 123 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.124 zhoneVdslLineConfUpPboPsdParamA3 OBJECT-TYPE SYNTAX Integer32 (4000..8096) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter A3. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 124 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.125 zhoneVdslLineConfUpPboPsdParamA4 OBJECT-TYPE SYNTAX Integer32 (4000..8096) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter A4. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 125 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.126 zhoneVdslLineConfUpPboPsdParamB3 OBJECT-TYPE SYNTAX Integer32 (0..4096) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter B3. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 126 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.127 zhoneVdslLineConfUpPboPsdParamB4 OBJECT-TYPE SYNTAX Integer32 (0..4096) UNITS ".01 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Upstream power backoff PSD parameter B4. This parameter is only used if the mask selection is set to PSDMaskABParameters" DEFVAL { 4000 } ::= { zhoneVdslLineConfProfileEntry 127 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.128 zhoneVdslLineConfFallbackDefaultVpi OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "ATM VPI to be used by the line when it trains in ADSL/ATM mode and bridges are configured for single-vc mode" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 128 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.129 zhoneVdslLineConfFallbackDefaultVci OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "ATM VCI to be used by the line when it trains in ADSL/ATM mode and bridges are configured for single-vc mode" DEFVAL { 35 } ::= { zhoneVdslLineConfProfileEntry 129 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.130 zhoneVdslLineConfDownGinpSupport OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable downstream G.INP / ITU-G.998.4. Only supported by Broadcom ports." REFERENCE "ITU-G.998.4" DEFVAL { disable } ::= { zhoneVdslLineConfProfileEntry 130 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.131 zhoneVdslLineConfUpGinpSupport OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable upstream G.INP / ITU-G.998.4. Only supported by Broadcom ports." DEFVAL { disable } ::= { zhoneVdslLineConfProfileEntry 131 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.132 zhoneVdslLineConfDownGinpEtrMax OBJECT-TYPE SYNTAX Unsigned32 (64..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpEtrMax - Maximum allowed value for downstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations. " REFERENCE "ITU-G.998.4" DEFVAL { 100000 } ::= { zhoneVdslLineConfProfileEntry 132 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.133 zhoneVdslLineConfUpGinpEtrMax OBJECT-TYPE SYNTAX Unsigned32 (64..2000000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpEtrMax - Maximum allowed value for upstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 60000 } ::= { zhoneVdslLineConfProfileEntry 133 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.134 zhoneVdslLineConfDownGinpEtrMin OBJECT-TYPE SYNTAX Unsigned32 (64..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpEtrMin - Minimum allowed value for downstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the minimum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 64 } ::= { zhoneVdslLineConfProfileEntry 134 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.135 zhoneVdslLineConfUpGinpEtrMin OBJECT-TYPE SYNTAX Unsigned32 (64..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpEtrMin - Minimum allowed value for upstream expected throughput (ETR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the minimum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 64 } ::= { zhoneVdslLineConfProfileEntry 135 } -- -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.136 zhoneVdslLineConfDownGinpNdrMax OBJECT-TYPE SYNTAX Unsigned32 (64..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpNdrMax - Maximum allowed value for downstream net data rate (NDR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 100000 } ::= { zhoneVdslLineConfProfileEntry 136 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.137 zhoneVdslLineConfUpGinpNdrMax OBJECT-TYPE SYNTAX Unsigned32 (64..200000) UNITS "kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpNdrMax - Maximum allowed value for upstream net data rate (NDR) in kbit/s. The valid values are all multiples of 8 from 0 to the maximum of the valid values of the maximum net data rate specified in the associated Recommendation. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 60000 } ::= { zhoneVdslLineConfProfileEntry 137 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.138 zhoneVdslLineConfDownGinpShineRatio OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "ratio" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpShineRatio - The downstream loss of rate in a 1 second interval expressed as a fraction of NDR due to a single high impulse noise event (SHINE) impulse noise environment expected by the operator to occur at a probability acceptable for the services. The valid values are all multiples of 0.001 from 0 to 0.1. This field uses 1 to equal 0.001 and 100 to equal 0.1. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 10 } ::= { zhoneVdslLineConfProfileEntry 138 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.139 zhoneVdslLineConfUpGinpShineRatio OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "ratio" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpShineRatio - The upstream loss of rate in a 1 second interval expressed as a fraction of NDR due to a single high impulse noise event (SHINE) impulse noise environment expected by the operator to occur at a probability acceptable for the services. The valid values are all multiples of 0.001 from 0 to 0.1. This field uses 1 to equal 0.001 and 100 to equal 0.1. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 10 } ::= { zhoneVdslLineConfProfileEntry 139 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.140 zhoneVdslLineConfDownGinpLeftrThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..99) UNITS "ratio" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpLeftrThreshold - The downstream rate Threshold below which the Low Error Free Rate (LEFTR) defect is declared. The threshold used to declare leftr defects is expressed in fraction of the net data rate (NDR). The value 0 is a special value to indicate that the receiver shall use a special value for declaring leftr defect. The minimum valid threshold to declare leftr is ETR/2. The receiver shall ignore threshold values that are less than the minimum and shall use ETR/2 for declaring leftr defect instead. The valid values are all multiples of 0.01 from 0.01 to 0.99. This field uses 1 to equal 0.01 and 99 to equal 0.99." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 140 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.141 zhoneVdslLineConfUpGinpLeftrThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..99) UNITS "ratio" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpLeftrThreshold - The upstream rate Threshold below which the Low Error Free Rate (LEFTR) defect is declared. The threshold used to declare leftr defects is expressed in fraction of the net data rate (NDR). The value 0 is a special value to indicate that the receiver shall use a special value for declaring leftr defect. The minimum valid threshold to declare leftr is ETR/2. The receiver shall ignore threshold values that are less than the minimum and shall use ETR/2 for declaring leftr defect instead. The valid values are all multiples of 0.01 from 0.01 to 0.99. This field uses 1 to equal 0.01 and 99 to equal 0.99." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 141 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.142 zhoneVdslLineConfDownGinpMaxDelay OBJECT-TYPE SYNTAX Unsigned32 (0..63) UNITS "mSecs" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpMaxDelay - The maximum downstream delay in ms. This is the upper limit for the delay that is added to the transmission delay only caused by retransmissions. Here the receiver and/or the transmitter shall identify and discard all DTUs whose payload cannot be transferred over the reference point at the receiver without violating the delay_max limit. The time stamp shall be the criterion for discarding the DTUs. The processing delay between the U-interface and the retransmission sub-layer of the receiver in the retransmission data path direction shall be excluded from consideration for delay_max in the retransmission data path direction. The valid values are all integers from 1 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp." REFERENCE "ITU-G.998.4" DEFVAL { 20 } ::= { zhoneVdslLineConfProfileEntry 142 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.143 zhoneVdslLineConfUpGinpMaxDelay OBJECT-TYPE SYNTAX Unsigned32 (0..63) UNITS "mSecs" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpMaxDelay - The maximum upstream delay in ms. This is the upper limit for the delay that is added to the transmission delay only caused by retransmissions. Here the receiver and/or the transmitter shall identify and discard all DTUs whose payload cannot be transferred over the reference point at the receiver without violating the delay_max limit. The time stamp shall be the criterion for discarding the DTUs. The processing delay between the U-interface and the retransmission sub-layer of the receiver in the retransmission data path direction shall be excluded from consideration for delay_max in the retransmission data path direction. The valid values are all integers from 1 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp." REFERENCE "ITU-G.998.4" DEFVAL { 20 } ::= { zhoneVdslLineConfProfileEntry 143 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.144 zhoneVdslLineConfDownGinpMinDelay OBJECT-TYPE SYNTAX Unsigned32 (0..63) UNITS "mSecs" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpMinDelay - The minimum downstream delay in ms. This is the lower limit for the delay that is added to the transmission delay caused by retransmissions only. The time stamp shall be used by the outlet shaping function to determine when the payload of the DTU shall be sent to the reference point to meet the delay limits. The outlet shaping function shall minimize the additional delay that may be introduced above delay_ min , and shall never exceed delay_max. The valid values are all integers from 0 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 144 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.145 zhoneVdslLineConfUpGinpMinDelay OBJECT-TYPE SYNTAX Unsigned32 (0..63) UNITS "mSecs" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpMinDelay - The minimum upstream delay in ms. This is the lower limit for the delay that is added to the transmission delay caused by retransmissions only. The time stamp shall be used by the outlet shaping function to determine when the payload of the DTU shall be sent to the reference point to meet the delay limits. The outlet shaping function shall minimize the additional delay that may be introduced above delay_ min , and shall never exceed delay_max. The valid values are all integers from 0 to 63. ITU-T G.998.4 7.1.1 Control parameters, 7.1.2 Valid configurations, and 8.1.6 Time Stamp." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 145 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.146 zhoneVdslLineConfDownGinpMin OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "symbols" MAX-ACCESS read-create STATUS current DESCRIPTION "ginpMin - The minimum downstream impulse noise protection (INP) against single high impulse noise event (SHINE) in discrete multitone (DMT) symbols. The valid values are all integers from 0 to 63 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 127 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 4 } ::= { zhoneVdslLineConfProfileEntry 146 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.147 zhoneVdslLineConfUpGinpMin OBJECT-TYPE SYNTAX Unsigned32 (0..127) UNITS "symbols" MAX-ACCESS read-create STATUS current DESCRIPTION "ginpMin - The minimum upstream impulse noise protection (INP) against single high impulse noise event (SHINE) in discrete multitone (DMT) symbols. The valid values are all integers from 0 to 63 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 127 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 4 } ::= { zhoneVdslLineConfProfileEntry 147 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.148 zhoneVdslLineConfDownGinpMinRSoverhead OBJECT-TYPE SYNTAX Unsigned32 (0..64) UNITS "ratio" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpMinRSoverhead - This value specifies the downstream bandwidth reserved for RS (reed-solomon) codewords. The minimum guaranteed R/N ratio. The unit is 1/256th and the range is 0..64 (0 to 25%)." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 148 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.149 zhoneVdslLineConfUpGinpMinRSoverhead OBJECT-TYPE SYNTAX Unsigned32 (0..64) UNITS "ratio" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpMinRSoverhead - This value specifies the upstream bandwidth reserved for RS (reed-solomon) codewords. The minimum guaranteed R/N ratio. The unit is 1/256th and the range is 0..64 (0 to 25%)." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 149 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.150 zhoneVdslLineConfDownGinpReinCfg OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "symbols" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpReinCfg - The minimum downstream impulse protection against electrical repetitive impulse noise (REIN) in DMT symbols. The valid values are all integers from 0 to 7 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 13 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 150 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.151 zhoneVdslLineConfUpGinpReinCfg OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "symbols" MAX-ACCESS read-create STATUS current DESCRIPTION "gInpReinCfg - The minimum upstream impulse protection against electrical repetitive impulse noise (REIN) in DMT symbols. The valid values are all integers from 0 to 7 for system with a sub-carrier spacing of 4.3125 kHz. The valid values are all integers from 0 to 13 for system with a sub-carrier spacing of 8.625 kHz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." REFERENCE "ITU-G.998.4" DEFVAL { 0 } ::= { zhoneVdslLineConfProfileEntry 151 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.152 zhoneVdslLineConfDownGinpReinFreq OBJECT-TYPE SYNTAX INTEGER { freq100hz(1), freq120hz(2) } UNITS "Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ginpReinFreq specifies the frequency of REIN inter-arrival time. It is used in the Channel Initialization Policy and on-line reconfiguration procedures. REIN is commonly coupled from electrical power cables appliances drawing power from the AC electrical power network, having a repetition rate of twice the AC power frequency (100 or 120 Hz). The valid values are integers 100 hz or 120 hz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." DEFVAL { freq120hz } ::= { zhoneVdslLineConfProfileEntry 152 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.153 zhoneVdslLineConfUpGinpReinFreq OBJECT-TYPE SYNTAX INTEGER { freq100hz(1), freq120hz(2) } UNITS "Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ginpReinFreq specifies the frequency of REIN inter-arrival time. It is used in the Channel Initialization Policy and on-line reconfiguration procedures. REIN is commonly coupled from electrical power cables appliances drawing power from the AC electrical power network, having a repetition rate of twice the AC power frequency (100 or 120 Hz). The valid values are integers 100 hz or 120 hz. ITU-T G.998.4 7.1.1 Control parameters and 7.1.2 Valid configurations." DEFVAL { freq120hz } ::= { zhoneVdslLineConfProfileEntry 153 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.154 zhoneVdslLineConfDownGinpRtxMode OBJECT-TYPE SYNTAX INTEGER { forbidden(1), preferred(2), forced(3), testmode(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "gInpRtxMode - Downstream retransmission Mode (RTX MODE). The RTX_MODE is a configuration parameter used to control activation of retransmission during initialization. This parameter has 4 valid values: FORBIDDEN: ITU-T G.998.4 retransmission not allowed. PREFERRED: ITU-T G.998.4 retransmission is preferred by the operator. (i.e., if ITU-T G.998.4 RTX capability is supported by both XTU's, the XTU's shall select ITU-T G.998.4 operation for this direction). FORCED: Force the use of the ITU-T G.998.4 retransmission. (i.e., if ITU-T G.998.4 RTX capability in this direction is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). NOTE: Due to the optionality of ITU-T G.998.4 retransmission in upstream direction, the use of FORCED in upstream may lead to initialization failure, even if the XTU is supporting ITU-T G.998.4 (in downstream). TESTMODE: Force the use of the ITU-T G.998.4 retransmission in the test mode described in clause 10.4. (i.e., if ITU-T G.998.4 RTX capability is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). ITU-T G.998.4 11.1.13 Retransmission Mode (RTX_MODE) " REFERENCE "ITU-G.998.4" DEFVAL { preferred } ::= { zhoneVdslLineConfProfileEntry 154 } -- 1.3.6.1.4.1.5504.5.13.1.1.11.1.155 zhoneVdslLineConfUpGinpRtxMode OBJECT-TYPE SYNTAX INTEGER { forbidden(1), preferred(2), forced(3), testmode(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "gInpRtxMode - Upstream retransmission Mode (RTX MODE). The RTX_MODE is a configuration parameter used to control activation of retransmission during initialization. This parameter has 4 valid values: FORBIDDEN: ITU-T G.998.4 retransmission not allowed. PREFERRED: ITU-T G.998.4 retransmission is preferred by the operator. (i.e., if ITU-T G.998.4 RTX capability is supported by both XTU's, the XTU's shall select ITU-T G.998.4 operation for this direction). FORCED: Force the use of the ITU-T G.998.4 retransmission. (i.e., if ITU-T G.998.4 RTX capability in this direction is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). NOTE: Due to the optionality of ITU-T G.998.4 retransmission in upstream direction, the use of FORCED in upstream may lead to initialization failure, even if the XTU is supporting ITU-T G.998.4 (in downstream). TESTMODE: Force the use of the ITU-T G.998.4 retransmission in the test mode described in clause 10.4. (i.e., if ITU-T G.998.4 RTX capability is not supported by both XTU's or not selected by the XTU's, an initialization failure shall result). ITU-T G.998.4 11.1.13 Retransmission Mode (RTX_MODE)" REFERENCE "ITU-G.998.4" DEFVAL { preferred } ::= { zhoneVdslLineConfProfileEntry 155 } -- Alarm configuration profile table -- -- 1.3.6.1.4.1.5504.5.13.1.1.20 -- 1.3.6.1.4.1.5504.5.13.1.1.20 zhoneVdslLineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the VDSL line alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line alarm thresholds. Entries in this table MUST be maintained in a persistent manner." ::= { zhoneVdslMibObjects 20 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1 -- 1.3.6.1.4.1.5504.5.13.1.1.20.1 zhoneVdslLineAlarmConfProfileEntry OBJECT-TYPE SYNTAX ZhoneVdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of a VDSL line alarm profile. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document." INDEX { ifIndex } ::= { zhoneVdslLineAlarmConfProfileTable 1 } ZhoneVdslLineAlarmConfProfileEntry ::= SEQUENCE { zhoneVdslLineAlarmConfProfileName SnmpAdminString, zhoneVdslLineAlarmConfThresh15MinLofs INTEGER, zhoneVdslLineAlarmConfThresh15MinLoss INTEGER, zhoneVdslLineAlarmConfThresh15MinLprs INTEGER, zhoneVdslLineAlarmConfThresh15MinLols INTEGER, zhoneVdslLineAlarmConfThresh15MinESs INTEGER, zhoneVdslLineAlarmConfThresh15MinSESs INTEGER, zhoneVdslLineAlarmConfThresh15MinUASs INTEGER, zhoneVdslLineAlarmConfInitFailure TruthValue, zhoneVdslLineAlarmConfProfRowStatus RowStatus, zhoneVdslLineAlarmConfThresh1DayLofs INTEGER, zhoneVdslLineAlarmConfThresh1DayLoss INTEGER, zhoneVdslLineAlarmConfThresh1DayLprs INTEGER, zhoneVdslLineAlarmConfThresh1DayLols INTEGER, zhoneVdslLineAlarmConfThresh1DayESs INTEGER, zhoneVdslLineAlarmConfThresh1DaySESs INTEGER, zhoneVdslLineAlarmConfThresh1DayUASs INTEGER, zhoneVdslLineAlarmConfThresh1DayInitFailure TruthValue } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.1 -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.1 zhoneVdslLineAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name for this profile as specified by an administrator." ::= { zhoneVdslLineAlarmConfProfileEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.2 zhoneVdslLineAlarmConfThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER (0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of frame seconds (LOFs) within any given 15-minute performance data collection interval. If the value of loss of frame seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLofsThreshNotification notification will be generated. No more than one notification will be sent per interval." ::= { zhoneVdslLineAlarmConfProfileEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.3 zhoneVdslLineAlarmConfThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER (0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of signal seconds (LOSs) within any given 15-minute performance data collection interval. If the value of loss of signal seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLossThreshNotification notification will be generated. One notification will be sent per interval per endpoint." ::= { zhoneVdslLineAlarmConfProfileEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.4 zhoneVdslLineAlarmConfThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER (0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of power seconds (LPRs) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLprsThreshNotification notification will be generated. No more than one notification will be sent per interval." ::= { zhoneVdslLineAlarmConfProfileEntry 4 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.5 zhoneVdslLineAlarmConfThresh15MinLols OBJECT-TYPE SYNTAX INTEGER (0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of link seconds (LOLs) within any given 15-minute performance data collection interval. If the value of loss of link seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfLolsThreshNotification notification will be generated. No more than one notification will be sent per interval." ::= { zhoneVdslLineAlarmConfProfileEntry 5 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.6 zhoneVdslLineAlarmConfThresh15MinESs OBJECT-TYPE SYNTAX INTEGER (0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of errored seconds (ESs) within any given 15-minute performance data collection interval. If the value of errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfEssThreshNotification notification will be generated. No more than one notification will be sent per interval." ::= { zhoneVdslLineAlarmConfProfileEntry 6 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.7 zhoneVdslLineAlarmConfThresh15MinSESs OBJECT-TYPE SYNTAX INTEGER (0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of severely errored seconds (SESs) within any given 15-minute performance data collection interval. If the value of severely errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfSessThreshNotification notification will be generated. No more than one notification will be sent per interval." ::= { zhoneVdslLineAlarmConfProfileEntry 7 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.8 zhoneVdslLineAlarmConfThresh15MinUASs OBJECT-TYPE SYNTAX INTEGER (0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of unavailable seconds (UASs) within any given 15-minute performance data collection interval. If the value of unavailable seconds in a particular 15-minute collection interval reaches/exceeds this value, a zhoneVdslPerfUassThreshNotification notification will be generated. No more than one notification will be sent per interval." ::= { zhoneVdslLineAlarmConfProfileEntry 8 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.9 zhoneVdslLineAlarmConfInitFailure OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies if a vdslInitFailureNotification notification will be generated if an initialization failure occurs." DEFVAL { false } ::= { zhoneVdslLineAlarmConfProfileEntry 9 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.10 -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.10 zhoneVdslLineAlarmConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time." ::= { zhoneVdslLineAlarmConfProfileEntry 10 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.11 zhoneVdslLineAlarmConfThresh1DayLofs OBJECT-TYPE SYNTAX INTEGER (0..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of frame seconds (LOFs) within any given 1-day performance data collection interval. If the value of loss of frame seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLofsThreshNotification notification will be generated. No more than one notification will be sent per interval" ::= { zhoneVdslLineAlarmConfProfileEntry 11 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.12 zhoneVdslLineAlarmConfThresh1DayLoss OBJECT-TYPE SYNTAX INTEGER (0..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of signal seconds (LOSs) within any given 1-day performance data collection interval. If the value of loss of signal seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLossThreshNotification notification will be generated. No more than one notification will be sent per interval" ::= { zhoneVdslLineAlarmConfProfileEntry 12 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.13 zhoneVdslLineAlarmConfThresh1DayLprs OBJECT-TYPE SYNTAX INTEGER (0..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of power seconds (LPRs) within any given 1-day performance data collection interval. If the value of loss of power seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLprsThreshNotification notification will be generated. No more than one notification will be sent per interval" ::= { zhoneVdslLineAlarmConfProfileEntry 13 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.14 zhoneVdslLineAlarmConfThresh1DayLols OBJECT-TYPE SYNTAX INTEGER (0..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of loss of link seconds (LOLs) within any given 1-day performance data collection interval. If the value of loss of link seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfLolsThreshNotification notification will be generated. No more than one notification will be sent per interval" ::= { zhoneVdslLineAlarmConfProfileEntry 14 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.15 zhoneVdslLineAlarmConfThresh1DayESs OBJECT-TYPE SYNTAX INTEGER (0..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of errored seconds (ESs) within any given 1-day performance data collection interval. If the value of errored seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfEssThreshNotification notification will be generated. No more than one notification will be sent per interval" ::= { zhoneVdslLineAlarmConfProfileEntry 15 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.16 zhoneVdslLineAlarmConfThresh1DaySESs OBJECT-TYPE SYNTAX INTEGER (0..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of severely errored seconds (SESs) within any given 1-day performance data collection interval. If the value of severely errored seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfSessThreshNotification notification will be generated. No more than one notification will be sent per interval" ::= { zhoneVdslLineAlarmConfProfileEntry 16 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.17 zhoneVdslLineAlarmConfThresh1DayUASs OBJECT-TYPE SYNTAX INTEGER (0..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "This object configures the threshold for the number of unavailable seconds (UASs) within any given 1-day performance data collection interval. If the value of unavailable seconds in a particular 1-day collection interval reaches/exceeds this value, a zhoneVdslPerfUasThreshNotification notification will be generated. No more than one notification will be sent per interval" ::= { zhoneVdslLineAlarmConfProfileEntry 17 } -- 1.3.6.1.4.1.5504.5.13.1.1.20.1.18 zhoneVdslLineAlarmConfThresh1DayInitFailure OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies if a vdslThresh1DayInitFailureNotification notification will be generated if an initialization failure occurs." DEFVAL { false } ::= { zhoneVdslLineAlarmConfProfileEntry 18 } -- 1.3.6.1.4.1.5504.5.13.1.1.21 zhoneVdslCustomNotchConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslCustomNotchConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains HAM (Handheld Amateur Radio) custom notch information." ::= { zhoneVdslMibObjects 21 } -- 1.3.6.1.4.1.5504.5.13.1.1.21.1 zhoneVdslCustomNotchConfProfileEntry OBJECT-TYPE SYNTAX ZhoneVdslCustomNotchConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each VDSL port can have custom notches." INDEX { ifIndex, zhoneVdslCustomNotchConfId } ::= { zhoneVdslCustomNotchConfProfileTable 1 } ZhoneVdslCustomNotchConfProfileEntry ::= SEQUENCE { zhoneVdslCustomNotchConfId Unsigned32, zhoneVdslCustomNotchConfStart Unsigned32, zhoneVdslCustomNotchConfStop Unsigned32 } -- 1.3.6.1.4.1.5504.5.13.1.1.21.1.1 zhoneVdslCustomNotchConfId OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS read-create STATUS current DESCRIPTION "Each VDSL2 port can have eight (8) custom notch pairs." ::= { zhoneVdslCustomNotchConfProfileEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.21.1.2 zhoneVdslCustomNotchConfStart OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the start frequency of custom HAM (Handheld Amateur Radio) notch. zhoneVdslCustomNotchConfStart MUST be less than or equal to zhoneVdslCustomNotchConfStop." ::= { zhoneVdslCustomNotchConfProfileEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.21.1.3 zhoneVdslCustomNotchConfStop OBJECT-TYPE SYNTAX Unsigned32 (0..200000) UNITS "kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the end frequency of custom HAM (Handheld Amateur Radio) notch. zhoneVdslCustomNotchConfStop MUST be greater than or equal to zhoneVdslCustomNotchConfStart." ::= { zhoneVdslCustomNotchConfProfileEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.22 zhoneVdslVectDataTable OBJECT-TYPE SYNTAX SEQUENCE OF ZhoneVdslVectDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Used to retrieve the vectoring packet counts." ::= { zhoneVdslMibObjects 22 } -- 1.3.6.1.4.1.5504.5.13.1.1.22.1 zhoneVdslVectDataEntry OBJECT-TYPE SYNTAX ZhoneVdslVectDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Vectoring Packet statistics data" INDEX { ifIndex } ::= { zhoneVdslVectDataTable 1 } ZhoneVdslVectDataEntry ::= SEQUENCE { zhoneVdslVectDataEsDsCounter Integer32, zhoneVdslVectDataEsUsCounter Integer32, zhoneVdslVectDataIsDsFeValid Integer32, zhoneVdslVectDataEsFeDsCounter Integer32 } -- 1.3.6.1.4.1.5504.5.13.1.1.22.1.1 zhoneVdslVectDataEsDsCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Error Sample Downstream Packet Counter" DEFVAL { 0 } ::= { zhoneVdslVectDataEntry 1 } -- 1.3.6.1.4.1.5504.5.13.1.1.22.1.2 zhoneVdslVectDataEsUsCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Error Sample Upstream Packet Counter" ::= { zhoneVdslVectDataEntry 2 } -- 1.3.6.1.4.1.5504.5.13.1.1.22.1.3 zhoneVdslVectDataIsDsFeValid OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Is Downstream Fe Valid" ::= { zhoneVdslVectDataEntry 3 } -- 1.3.6.1.4.1.5504.5.13.1.1.22.1.4 zhoneVdslVectDataEsFeDsCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Error Sample Fe Downstream Counter" ::= { zhoneVdslVectDataEntry 4 } -- conformance information -- 1.3.6.1.4.1.5504.5.13.1.3 -- 1.3.6.1.4.1.5504.5.13.1.3 zhoneVdslConformance OBJECT IDENTIFIER ::= { zhoneVdslLineMib 3 } -- 1.3.6.1.4.1.5504.5.13.1.3.1 -- 1.3.6.1.4.1.5504.5.13.1.3.1 zhoneVdslGroups OBJECT IDENTIFIER ::= { zhoneVdslConformance 1 } -- units of conformance -- 1.3.6.1.4.1.5504.5.13.1.3.1.1 -- 1.3.6.1.4.1.5504.5.13.1.3.1.1 zhoneVdslGroup OBJECT-GROUP OBJECTS { zhoneVdslLineCoding, zhoneVdslLineType, zhoneVdslLineConfProfile, zhoneVdslLineAlarmConfProfile, zhoneVdslPhysInvSerialNumber, zhoneVdslPhysInvVendorID, zhoneVdslPhysInvVersionNumber, zhoneVdslPhysCurrSnrMgn, zhoneVdslPhysCurrAtn, zhoneVdslPhysCurrStatus, zhoneVdslPhysCurrOutputPwr, zhoneVdslPhysCurrAttainableRate, zhoneVdslPhysCurrLineRate, zhoneVdslChanInterleaveDelay, zhoneVdslChanCrcBlockLength, zhoneVdslChanCurrTxRate, zhoneVdslChanCurrTxSlowBurstProtect, zhoneVdslChanCurrTxFastFec, zhoneVdslPerfDataValidIntervals, zhoneVdslPerfDataInvalidIntervals, zhoneVdslPerfDataLofs, zhoneVdslPerfDataLoss, zhoneVdslPerfDataLprs, zhoneVdslPerfDataLols, zhoneVdslPerfDataESs, zhoneVdslPerfDataSESs, zhoneVdslPerfDataUASs, zhoneVdslPerfDataInits, zhoneVdslPerfDataCurr15MinTimeElapsed, zhoneVdslPerfDataCurr15MinLofs, zhoneVdslPerfDataCurr15MinLoss, zhoneVdslPerfDataCurr15MinLprs, zhoneVdslPerfDataCurr15MinLols, zhoneVdslPerfDataCurr15MinESs, zhoneVdslPerfDataCurr15MinSESs, zhoneVdslPerfDataCurr15MinUASs, zhoneVdslPerfDataCurr15MinInits, zhoneVdslPerfData1DayValidIntervals, zhoneVdslPerfData1DayInvalidIntervals, zhoneVdslPerfDataCurr1DayTimeElapsed, zhoneVdslPerfDataCurr1DayLofs, zhoneVdslPerfDataCurr1DayLoss, zhoneVdslPerfDataCurr1DayLprs, zhoneVdslPerfDataCurr1DayLols, zhoneVdslPerfDataCurr1DayESs, zhoneVdslPerfDataCurr1DaySESs, zhoneVdslPerfDataCurr1DayUASs, zhoneVdslPerfDataCurr1DayInits, zhoneVdslPerfIntervalLofs, zhoneVdslPerfIntervalLoss, zhoneVdslPerfIntervalLprs, zhoneVdslPerfIntervalLols, zhoneVdslPerfIntervalESs, zhoneVdslPerfIntervalSESs, zhoneVdslPerfIntervalUASs, zhoneVdslPerfIntervalInits, zhoneVdslPerf1DayIntervalMoniSecs, zhoneVdslPerf1DayIntervalLofs, zhoneVdslPerf1DayIntervalLoss, zhoneVdslPerf1DayIntervalLprs, zhoneVdslPerf1DayIntervalLols, zhoneVdslPerf1DayIntervalESs, zhoneVdslPerf1DayIntervalSESs, zhoneVdslPerf1DayIntervalUASs, zhoneVdslPerf1DayIntervalInits, zhoneVdslChanValidIntervals, zhoneVdslChanInvalidIntervals, zhoneVdslChanFixedOctets, zhoneVdslChanBadBlks, zhoneVdslChanCurr15MinTimeElapsed, zhoneVdslChanCurr15MinFixedOctets, zhoneVdslChanCurr15MinBadBlks, zhoneVdslChan1DayValidIntervals, zhoneVdslChan1DayInvalidIntervals, zhoneVdslChanCurr1DayTimeElapsed, zhoneVdslChanCurr1DayFixedOctets, zhoneVdslChanCurr1DayBadBlks, zhoneVdslChanIntervalFixedOctets, zhoneVdslChanIntervalBadBlks, zhoneVdslChan1DayIntervalMoniSecs, zhoneVdslChan1DayIntervalFixedOctets, zhoneVdslChan1DayIntervalBadBlks, zhoneVdslLineConfDownRateMode, zhoneVdslLineConfUpRateMode, zhoneVdslLineConfDownMaxPwr, zhoneVdslLineConfUpMaxPwr, zhoneVdslLineConfDownMaxSnrMgn, zhoneVdslLineConfDownMinSnrMgn, zhoneVdslLineConfDownTargetSnrMgn, zhoneVdslLineConfUpMaxSnrMgn, zhoneVdslLineConfUpMinSnrMgn, zhoneVdslLineConfUpTargetSnrMgn, zhoneVdslLineConfDownFastMaxDataRate, zhoneVdslLineConfDownFastMinDataRate, zhoneVdslLineConfDownSlowMaxDataRate, zhoneVdslLineConfDownSlowMinDataRate, zhoneVdslLineConfUpFastMaxDataRate, zhoneVdslLineConfUpFastMinDataRate, zhoneVdslLineConfUpSlowMaxDataRate, zhoneVdslLineConfUpSlowMinDataRate, zhoneVdslLineConfDownRateRatio, zhoneVdslLineConfUpRateRatio, zhoneVdslLineConfDownMaxInterDelay, zhoneVdslLineConfUpMaxInterDelay, zhoneVdslLineConfDownPboControl, zhoneVdslLineConfUpPboControl, zhoneVdslLineConfDownPboLevel, zhoneVdslLineConfUpPboLevel, zhoneVdslLineConfDeploymentScenario, zhoneVdslLineConfAdslPresence, zhoneVdslLineConfApplicableStandard, zhoneVdslLineConfBandPlan, zhoneVdslLineConfBandPlanFx, zhoneVdslLineConfBandOptUsage, zhoneVdslLineConfUpPsdTemplate, zhoneVdslLineConfDownPsdTemplate, zhoneVdslLineConfHamBandMask, zhoneVdslLineConfCustomNotch1Start, zhoneVdslLineConfCustomNotch1Stop, zhoneVdslLineConfCustomNotch2Start, zhoneVdslLineConfCustomNotch2Stop, zhoneVdslLineConfDownTargetSlowBurst, zhoneVdslLineConfUpTargetSlowBurst, zhoneVdslLineConfDownMaxFastFec, zhoneVdslLineConfUpMaxFastFec, zhoneVdslLineConfLineType, zhoneVdslLineConfProfRowStatus, zhoneVdslLineAlarmConfThresh15MinLofs, zhoneVdslLineAlarmConfThresh15MinLoss, zhoneVdslLineAlarmConfThresh15MinLprs, zhoneVdslLineAlarmConfThresh15MinLols, zhoneVdslLineAlarmConfThresh15MinESs, zhoneVdslLineAlarmConfThresh15MinSESs, zhoneVdslLineAlarmConfThresh15MinUASs, zhoneVdslLineAlarmConfInitFailure, zhoneVdslLineAlarmConfThresh1DayLofs, zhoneVdslLineAlarmConfThresh1DayLoss, zhoneVdslLineAlarmConfThresh1DayLprs, zhoneVdslLineAlarmConfThresh1DayLols, zhoneVdslLineAlarmConfThresh1DayInitFailure, zhoneVdslLineConfAutoModeCrtrn, zhoneVdslLineConfAdslBandMode, zhoneVdslLineConfAdslBandModeEndFreq, zhoneVdslLineConfSeltAgc, zhoneVdslLineConfVdsl2Profile, zhoneVdslLineConfVdslMode, zhoneVdslLineConfPboElectricalOverride, zhoneVdslLineConfDownMaxPsd, zhoneVdslLineConfDownMaxAggregateTxPwr, zhoneVdslLineConfDownPsdShape, zhoneVdslLineConfDownVirtualNoiseSnrMode, zhoneVdslLineConfDownGhsA43TonePwr, zhoneVdslLineConfDownErasureDetectionFast, zhoneVdslLineConfDownErasureDetectionInterleave, zhoneVdslLineConfDownGhsB43TonePwr, zhoneVdslLineConfDownGhsV43TonePwr, zhoneVdslLineConfDownGhsA43TonePwrMaxLvl, zhoneVdslLineConfDownGhsA43cTonePwrMaxLvl, zhoneVdslLineConfDownGhsB43TonePwrMaxLvl, zhoneVdslLineConfDownGhsV43TonePwrMaxLvl, zhoneVdslLineConfDownRsCoding, zhoneVdslLineAlarmConfProfRowStatus, zhoneVdslLineConfUpErasureDetectionFast, zhoneVdslLineConfUpPboPsdParamB1, zhoneVdslLineConfUpPboPsdParamA1, zhoneVdslLineConfUpPboPsdParamA2, zhoneVdslLineConfUpPboPsdParamB2, zhoneVdslLineConfUpVirtualNoiseSnrMode, zhoneVdslLineConfUpErasureDetectionInterleave, zhoneVdslLineConfUpRsCoding, zhoneVdslLineConfUpPsdShape, zhoneVdslLineConfUpPboPsdTemplate, zhoneVdslLineConfNetworkTimingRef, zhoneVdslLineConfUpMaxAggregateTxPwr, zhoneVdslLineConfDownTrellis, zhoneVdslLineConfUpTrellis, zhoneVdslLineConfUpMaxPsd, zhoneVdslLineAlarmConfThresh1DayESs, zhoneVdslLineAlarmConfThresh1DaySESs, zhoneVdslLineAlarmConfThresh1DayUASs, zhoneVdslLineConfSeltEchoMeasurementTime, zhoneVdslCustomNotchConfStop, zhoneVdslLineConfSeltNoiseMeasurementTime, zhoneVdslCustomNotchConfStart, zhoneVdslLineConfTransmissionMode, zhoneVdslLineConfDownDownshiftSnrMgn, zhoneVdslLineConfDownUpshiftSnrMgn, zhoneVdslLineConfDownMinDownshiftTime, zhoneVdslLineConfDownMinUpshiftTime, zhoneVdslLineConfUpDownshiftSnrMgn, zhoneVdslLineConfUpUpshiftSnrMgn, zhoneVdslLineConfUpMinDownshiftTime, zhoneVdslLineConfUpMinUpshiftTime, zhoneVdslCustomNotchConfId, zhoneVdslLineConfDownGhsA43cTonePwr, zhoneVdslLineConfDMTConfMode, zhoneVdslLineConfPotsBypassRelayMaxDuration, zhoneVdslLineConfDownBitSwap, zhoneVdslLineConfUpBitSwap, zhoneVdslLineConfAdslAnnexMModeEnabled, zhoneVdslLineConfAdslAnnexMPsdMask, zhoneVdslLineConfUs0BoundaryTone, zhoneVdslLineConfDownInp, zhoneVdslLineConfUpInp, zhoneVdslLineConfDownMaxInterleavingDelay, zhoneVdslLineConfUpMaxInterleavingDelay, zhoneVdslLineConfDownPsdMaskEnable, zhoneVdslLineConfUpPsdMaskEnable, zhoneVdslLineConfDownPsdMaskSelect, zhoneVdslLineConfUpPsdMaskSelect, zhoneVdslPhysCurrProfile, zhoneVdslPhysCurrConnType, zhoneVdslLineEnableTrellisCoding, zhoneVdslLineEnableRsCoding, zhoneVdslLineConfPsdShape, zhoneVdslLineConfDownPhyRSupport, zhoneVdslLineConfUpPhyRSupport, zhoneVdslLineConfDownPhyRmaxINP, zhoneVdslLineConfUpPhyRmaxINP, zhoneVdslLineConfDownPhyRminRSoverhead, zhoneVdslLineConfUpPhyRminRSoverhead, zhoneVdslLineConfDownPhyRRtxRatio, zhoneVdslLineConfUpPhyRRtxRatio, zhoneVdslLineConfUpPboPsdParamA3, zhoneVdslLineConfUpPboPsdParamA4, zhoneVdslLineConfUpPboPsdParamB3, zhoneVdslLineConfUpPboPsdParamB4, zhoneVdslLineConfFallbackDefaultVpi, zhoneVdslLineConfFallbackDefaultVci, zhoneVdslLineConfUpMinTxThresholdAlarm, zhoneVdslLineConfDownMinTxThresholdAlarm } STATUS current DESCRIPTION "A collection of objects providing information about a VDSL Line." ::= { zhoneVdslGroups 1 } -- 1.3.6.1.4.1.5504.5.13.1.3.1.2 -- 1.3.6.1.4.1.5504.5.13.1.3.1.2 zhoneVdslNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { vdslXtucPerf15MinLofsThreshTrap, vdslXtucPerf15MinLossThreshTrap, vdslXtucPerf15MinLprsThreshTrap, vdslXtucPerf15MinLolsThreshTrap, vdslXtucPerf15MinESsThreshTrap, vdslXtucPerf15MinSESsThreshTrap, vdslXtucPerf15MinUASsThreshTrap, vdslXtucPerf1DayLofsThreshTrap, vdslXtucPerf1DayLossThreshTrap, vdslXtucPerf1DayLprsThreshTrap, vdslXtucPerf1DayLolsThreshTrap, vdslXtucPerf1DayESsThreshTrap, vdslXtucPerf1DaySESsThreshTrap, vdslXtucPerf1DayUASsThreshTrap, zhoneVdslInitFailureTrap, vdslXtucMinTxThresholdAlarmFailureTrap, vdslXturMinTxThresholdAlarmFailureTrap } STATUS current DESCRIPTION "This group supports notifications of significant conditions associated with VDSL Lines." ::= { zhoneVdslGroups 2 } -- 1.3.6.1.4.1.5504.5.13.1.3.2 -- 1.3.6.1.4.1.5504.5.13.1.3.2 zhoneVdslCompliances OBJECT IDENTIFIER ::= { zhoneVdslConformance 2 } -- this module -- 1.3.6.1.4.1.5504.5.13.1.3.2.1 -- this module -- 1.3.6.1.4.1.5504.5.13.1.3.2.1 zhoneVdslLineMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage VDSL interfaces." MODULE -- this module MANDATORY-GROUPS { zhoneVdslGroup, zhoneVdslNotificationGroup } ::= { zhoneVdslCompliances 1 } END -- -- phyVdsl.mib --