--MibName=rcMvr -- ***************************************************************** -- switch-mvr-mib.mib: Raisecom MVR MIB file -- -- May 2005, zhaohongce -- -- Copyright (c) 1994-2000, 2001 by Raisecom, Inc. -- All rights reserved. -- -- ***************************************************************** SWITCH-MVR-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32 FROM SNMPv2-SMI RowStatus,TruthValue FROM SNMPv2-TC PortList, Vlanset, EnableVar FROM SWITCH-TC iscomSwitch FROM RAISECOM-BASE-MIB; rcMvr MODULE-IDENTITY LAST-UPDATED "0506200000Z" ORGANIZATION "raisecom Group" CONTACT-INFO " Raise Systems Postal: Beijing, China Tel: 86-010-82884499 E-mail: zhaohongce@raisecom.com" DESCRIPTION "The MIB module for MVR and igmp filter." ::= { iscomSwitch 21} ------------------------------------------------------------------------------ -- -- rcMvr - IGMP filter and MVR Parameters -- -- This group is used to instrument the Layer 2 IGMP filter and MVR support. -- ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ rcMvrConfig OBJECT IDENTIFIER ::= { rcMvr 1 } rcIgmpFilterConfig OBJECT IDENTIFIER ::= { rcMvr 2 } ------------------------------------------------------------------------------ -- -- MVR Config Group -- rcMvrEnable OBJECT-TYPE SYNTAX EnableVar MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls whether the MVR is enabled on the device. A disable(2) value will prevent the MVR on the device." DEFVAL { disable } ::= { rcMvrConfig 1 } rcMvrVlan OBJECT-TYPE SYNTAX Vlanset MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the multicast VLAN ID, which is connected to multicast router." ::= { rcMvrConfig 2 } rcMvrMaxGroups OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum MVR multicast groups supported by this device." ::= { rcMvrConfig 3 } rcMvrCurrentGroups OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current MVR multicast groups configured by user." ::= { rcMvrConfig 4 } rcMvrQureyTime OBJECT-TYPE SYNTAX INTEGER (60..36000) UNITS "tenths of second" MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the MVR entry will be timeout if no REPORT packet received after the time." DEFVAL {600} ::= { rcMvrConfig 5 } rcMvrOperMode OBJECT-TYPE SYNTAX INTEGER {dynamic(1),compatible(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the MVR operate mode. A value of dynamic(1) Indicates the uplink port will initiatively send JOIN packet to the multicast group, compatible(2) indicates the join action is determined by user hosts." DEFVAL { compatible } ::= { rcMvrConfig 6 } rcMvrGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF RcMvrGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains entries that identify lists of IP Multicast groups configured on the device. " ::= { rcMvrConfig 7 } rcMvrGroupEntry OBJECT-TYPE SYNTAX RcMvrGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rcMvrGroupTable. The entry identify the IP multicast groups which user want to receive." INDEX { rcMvrGroupVlan, rcMvrGroupAddress } ::= { rcMvrGroupTable 1 } RcMvrGroupEntry ::= SEQUENCE { rcMvrGroupVlan INTEGER, rcMvrGroupAddress IpAddress, rcMvrGroupRowStatus RowStatus } rcMvrGroupVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying this entry. the multicast vlan of this groups which user want to receive." ::= { rcMvrGroupEntry 1 } rcMvrGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying this entry. the IP multicast groups which user want to receive." ::= { rcMvrGroupEntry 2 } rcMvrGroupRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-create STATUS current DESCRIPTION "The row status of this entry." ::= { rcMvrGroupEntry 3 } -- -- MVR Information Group -- rcMvrIFTable OBJECT-TYPE SYNTAX SEQUENCE OF RcMvrIFEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains entries that identify the configured MVR information for each port." ::= { rcMvrConfig 8 } rcMvrIFEntry OBJECT-TYPE SYNTAX RcMvrIFEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rcMvrGroupTable. The entry identify the configured MVR information for the port." INDEX { rcMvrPortIndex } ::= { rcMvrIFTable 1 } RcMvrIFEntry ::= SEQUENCE { rcMvrPortIndex INTEGER, rcMvrPortEnable TruthValue, rcMvrType INTEGER, rcMvrImmediate EnableVar, rcMvrPortStatus INTEGER } rcMvrPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying this entry." ::= { rcMvrIFEntry 1 } rcMvrPortEnable OBJECT-TYPE SYNTAX EnableVar MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls whether the MVR is enabled on the port. A false disable(2) will prevent the MVR on the port, and the configuration on the port will be set to default value." ::= { rcMvrIFEntry 2 } rcMvrType OBJECT-TYPE SYNTAX INTEGER { non-mvr(0),source(1), receiver(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object describes the MVR type of the port. source(1) specifies the port as uplink port which receive the multicast flow sent by router.receiver(2) specifies the port connected to user host.non-mvr(0) specifies the port is neither source nor receiver." ::= { rcMvrIFEntry 3 } rcMvrImmediate OBJECT-TYPE SYNTAX EnableVar MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the whether enable the immediate leave. enable(1) specifies enable the immediate leave." ::= { rcMvrIFEntry 4 } rcMvrPortStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the status of the port. Active(1) specifies the port is a part of a VLAN. Inactive(2) specifies the port is not a part of a VLAN." ::= { rcMvrIFEntry 5 } -- -- The per interface MVR configuration table -- rcMvrMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF RcMvrMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of IP multicast group that allow user join." ::= { rcMvrConfig 9 } rcMvrMemberEntry OBJECT-TYPE SYNTAX RcMvrMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the IP multicast group that allow user join." INDEX { rcMvrMemberPort,rcMvrMemberVlan,rcMvrMemberGroupAddress} ::= { rcMvrMemberTable 1 } RcMvrMemberEntry ::= SEQUENCE { rcMvrMemberPort INTEGER, rcMvrMemberVlan INTEGER, rcMvrMemberGroupAddress IpAddress, rcMvrMemberGroupType INTEGER, rcMvrMemberRowStatus RowStatus, rcMvrMemberReplicableVlans Vlanset } rcMvrMemberPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying this entry." ::= { rcMvrMemberEntry 1 } rcMvrMemberVlan OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the multicast VLAN that allow user join." ::= { rcMvrMemberEntry 2 } rcMvrMemberGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the IP multicast group that allow user join." ::= { rcMvrMemberEntry 3 } rcMvrMemberGroupType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object defines the status of the multicast group. static(1) specifies the port join the IP multicast group by staticly configured. dynamic(2) specifies the port join the IP multicast group by IGMP join packet." ::= { rcMvrMemberEntry 4 } rcMvrMemberRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of this entry. When the 'rcMvrEnable' and 'rcMvrIpmcReplicationEnable' object are both enabled, the Max access of this object is read-only." ::= { rcMvrMemberEntry 5 } rcMvrMemberReplicableVlans OBJECT-TYPE SYNTAX Vlanset MAX-ACCESS read-only STATUS current DESCRIPTION "The IP multicast replicaton vlan bitlist." ::= { rcMvrMemberEntry 6 } -- -- MVR port statistics information table -- rcMvrPortStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF RcMvrPortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains entries that note statistics information of the IGMP packets received on each port." ::= { rcMvrConfig 10 } rcMvrPortStatisticsEntry OBJECT-TYPE SYNTAX RcMvrPortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the statistics information of the IGMP packets received on each port." INDEX { rcMvrPortStatisticsPortid } ::= { rcMvrPortStatisticsTable 1 } RcMvrPortStatisticsEntry ::= SEQUENCE { rcMvrPortStatisticsPortid INTEGER, rcMvrPortStatisticsClear INTEGER, rcMvrPortStatisticsRecvQueryPkts Counter, rcMvrPortStatisticsRecvReportPkts Counter, rcMvrPortStatisticsRecvLeavePkts Counter, rcMvrPortStatisticsDropQueryPkts Counter, rcMvrPortStatisticsDropReportPkts Counter, rcMvrPortStatisticsDropLeavePkts Counter, rcMvrPortLastReplaceNewMulticast IpAddress, rcMvrPortLastReplaceOldMulticast IpAddress, rcMvrPortReplaceTotalCount Counter } rcMvrPortStatisticsPortid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying this entry." ::= { rcMvrPortStatisticsEntry 1 } rcMvrPortStatisticsClear OBJECT-TYPE SYNTAX INTEGER {read(0),clear(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object 1 to clear all the information of MVR port statistics. Get this object will always return 0." ::= { rcMvrPortStatisticsEntry 2 } rcMvrPortStatisticsRecvQueryPkts OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the count of query packet received on this port." ::= { rcMvrPortStatisticsEntry 3 } rcMvrPortStatisticsRecvReportPkts OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the count of report packet received on this port." ::= { rcMvrPortStatisticsEntry 4 } rcMvrPortStatisticsRecvLeavePkts OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the count of leave packet received on this port." ::= { rcMvrPortStatisticsEntry 5 } rcMvrPortStatisticsDropQueryPkts OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the count of query packet droped on this port." ::= { rcMvrPortStatisticsEntry 6 } rcMvrPortStatisticsDropReportPkts OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the count of report packet droped on this port." ::= { rcMvrPortStatisticsEntry 7 } rcMvrPortStatisticsDropLeavePkts OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the count of leave packet droped on this port." ::= { rcMvrPortStatisticsEntry 8 } rcMvrPortLastReplaceNewMulticast OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the new multicast IP address of the last replace." ::= { rcMvrPortStatisticsEntry 9 } rcMvrPortLastReplaceOldMulticast OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes the old multicast IP address of the last replace." ::= { rcMvrPortStatisticsEntry 10 } rcMvrPortReplaceTotalCount OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "The object notes count of replace taken place on this port." ::= { rcMvrPortStatisticsEntry 11 } rcMvrProxySuppressionEnable OBJECT-TYPE SYNTAX EnableVar MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls whether the proxy suppression is enabled on the device. A disable(2) value will prevent the proxy suppression on the device." DEFVAL { disable } ::= { rcMvrConfig 11 } rcIgmpQuerierEnable OBJECT-TYPE SYNTAX EnableVar MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls whether the IGMP querier is enabled on the device. A disable(2) value will prevent the IGMP querier on the device." DEFVAL { disable } ::= { rcMvrConfig 12 } rcMvrProxySourceIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object specify the source IP address for MVR proxy and querier. If not configure this object ,the default value is the IP address on IP interface 0.Then if the IP address on IP interface 0 is none, the default value is 0.0.0.0." ::= { rcMvrConfig 13 } rcIgmpQueryInterval OBJECT-TYPE SYNTAX INTEGER (10..65535) UNITS "Seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specify interval time that querier send general query packet. The default value is 60s." DEFVAL {60} ::= { rcMvrConfig 14 } rcMvrProxyQueryMaxReponseInterval OBJECT-TYPE SYNTAX INTEGER (1..25) UNITS "Seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specify max response time for host to response the MVR proxy. The default value is 10s." DEFVAL {10} ::= { rcMvrConfig 15 } rcMvrProxyQueryLastMemberInterval OBJECT-TYPE SYNTAX INTEGER (1..25) UNITS "Seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specify last member query interval.When last member leave the group,MVR proxy will send the special group query packet.If MVR proxy receive none report packet of this group in the last member query interval, MVR proxy will delete this group from multicast transmit table.The default value is 1s." DEFVAL {1} ::= { rcMvrConfig 16 } rcMvrIpmcReplicationEnable OBJECT-TYPE SYNTAX EnableVar MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls whether the IP multicast replication is enabled on the device. A disable(2) value will prevent the IP multicast replication on the device. The ` rcMvrEnable ' object must be set to `disable' prior to modify this object value. If 'rcMvrEnable' and 'rcMvrIpmcReplicationEnable' are both enabled , setting ` rcMvrEnable ' to `disable' will automatically set 'rcMvrIpmcReplicationEnable' to `disable'." DEFVAL {disable} ::= { rcMvrConfig 17 } ------------------------------------------------------------------------------ -- -- IGMP Filter Config Group -- rcIgmpFilterEnable OBJECT-TYPE SYNTAX EnableVar MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls whether the IGMP filtering is enabled on the device. A disable(2) value will prevent the IGMP filtering action on the device." DEFVAL { enable } ::= { rcIgmpFilterConfig 1 } rcIgmpFilterMaxProfiles OBJECT-TYPE SYNTAX INTEGER UNITS "profiles" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum number of profiles supported by this device. A value of zero indicates no limitation on the number of profiles." ::= { rcIgmpFilterConfig 2 } -- -- IGMP Filter Information Group -- rcIgmpFilterAddEntry OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates adding a IGMP profile entry. The value imply the profile number." ::= { rcIgmpFilterConfig 3 } rcIgmpFilterDelEntry OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates deleting a IGMP profile entry. The value imply the profile number." ::= { rcIgmpFilterConfig 4 } rcIgmpFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF RcIgmpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains entries that identify lists of IP Multicast groups for each profile configured on the device. Each entry contains a range of contiguous IP Multicast groups associated to a profile index. Multiple rcIgmpFilterEntry may be associated with the same rcIgmpFilterProfileIndex. All the rcIgmpFilterEntry with the same profile index are subjected to the same IGMP filtering action as defined in rcIgmpFilterProfileAction. Each profile index may be associated with zero or more ports through rcIgmpFilterIFPortIndex object in rcIgmpFilterIFTable. The maximum number of entries is determined by rcIgmpFilterMaxProfiles." ::= { rcIgmpFilterConfig 5 } rcIgmpFilterEntry OBJECT-TYPE SYNTAX RcIgmpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the rcIgmpFilterTable." INDEX { rcIgmpFilterProfileIndex, rcIgmpFilterStartAddress } ::= { rcIgmpFilterTable 1 } RcIgmpFilterEntry ::= SEQUENCE { rcIgmpFilterProfileIndex INTEGER, rcIgmpFilterStartAddress IpAddress, rcIgmpFilterEndAddress IpAddress, rcIgmpFilterProfileAction INTEGER, rcIgmpFilterRowStatus RowStatus } rcIgmpFilterProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying this entry." ::= { rcIgmpFilterEntry 1 } rcIgmpFilterStartAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object describes the start of the IP multicast group address of a contiguous range which will be subjected to filtering operation." ::= { rcIgmpFilterEntry 2 } rcIgmpFilterEndAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the end of the IP multicast group address of a contiguous range which will be subjected to filtering operation." ::= { rcIgmpFilterEntry 3 } rcIgmpFilterProfileAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines the action for filtering IGMP reports for this profile. If the object is set to deny(2): then all IGMP reports associated to IP multicast groups included in the profile identified by rcIgmpFilterProfileIndex will be dropped. If the object is set to permit(1): then all IGMP reports associated to IP multicast groups not included in the profile identified by rcIgmpFilterProfileIndex will be dropped." DEFVAL { permit } ::= { rcIgmpFilterEntry 4 } rcIgmpFilterRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-create STATUS current DESCRIPTION "The row status of this entry." ::= { rcIgmpFilterEntry 5 } -- -- The per interface IGMP filtering configuration table -- rcIgmpFilterIFTable OBJECT-TYPE SYNTAX SEQUENCE OF RcIgmpFilterIFEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of ports that can support IGMP filter feature." ::= { rcIgmpFilterConfig 6 } rcIgmpFilterIFEntry OBJECT-TYPE SYNTAX RcIgmpFilterIFEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the configuration for associating the IGMP filter profile index with the port. An entry is created for each of the IGMP filter capable port on the system. The entry is removed on removal of corresponding port from system." INDEX { rcIgmpFilterIFPortIndex } ::= { rcIgmpFilterIFTable 1 } RcIgmpFilterIFEntry ::= SEQUENCE { rcIgmpFilterIFPortIndex INTEGER, rcIgmpFilterIFProfileIndex INTEGER, rcIgmpFilterIFMaxGroups INTEGER, rcIgmpFilterIFCurrentGroups INTEGER, rcIgmpFilterIFMaxGroupsAction INTEGER } rcIgmpFilterIFPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies which IGMP filter profile applies to this port. If the value of this MIB object matches the value of rcIgmpFilterProfileIndex in rcIgmpFilterTable, the corresponding profile configuration will apply to this port. A value of zero indicates no profile is associated with corresponding port. The filtering action on each port is also defined by the associated profile." ::= { rcIgmpFilterIFEntry 1 } rcIgmpFilterIFProfileIndex OBJECT-TYPE SYNTAX INTEGER (0..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies which IGMP filter profile applies to this port. If the value of this MIB object matches the value of rcIgmpFilterProfileIndex in rcIgmpFilterTable, the corresponding profile configuration will apply to this interface. A value of zero indicates no profile is associated with corresponding port. The filtering action on each port is also defined by the associated profile." ::= { rcIgmpFilterIFEntry 2 } rcIgmpFilterIFMaxGroups OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the max multicast group numbers that allow this port join. A value of zero indicates no max limitation is associated with corresponding interface." DEFVAL { 0 } ::= { rcIgmpFilterIFEntry 3 } rcIgmpFilterIFCurrentGroups OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the current multicast group numbers that this port has joined." ::= { rcIgmpFilterIFEntry 4 } rcIgmpFilterIFMaxGroupsAction OBJECT-TYPE SYNTAX INTEGER { deny(1), replace(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies which action will take place on the port when exceed the max multicast group numbers. A value of deny(1) indicates deny join the multicast group when exceed the max multicast group numbers. A value of replace(2) indicates allow to replace the existed multicast group when exceed the max multicast group numbers.But now not supported." DEFVAL { deny } ::= { rcIgmpFilterIFEntry 5 } -- -- The per vlan IGMP filtering configuration table -- rcIgmpFilterVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF RcIgmpFilterVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of vlans that can support IGMP filter feature." ::= { rcIgmpFilterConfig 7 } rcIgmpFilterVlanEntry OBJECT-TYPE SYNTAX RcIgmpFilterVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the configuration for associating the IGMP filter profile index with the vlan. " INDEX { rcIgmpFilterIFPortIndex } ::= { rcIgmpFilterVlanTable 1 } RcIgmpFilterVlanEntry ::= SEQUENCE { rcIgmpFilterVLANIndex INTEGER, rcIgmpFilterVlanProfileIndex INTEGER, rcIgmpFilterVlanMaxGroups INTEGER, rcIgmpFilterVlanCurrentGroups INTEGER, rcIgmpFilterVlanMaxGroupsAction INTEGER } rcIgmpFilterVLANIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying this entry." ::= { rcIgmpFilterVlanEntry 1 } rcIgmpFilterVlanProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies which IGMP filter profile applies to this vlan. If the value of this MIB object matches the value of rcIgmpFilterProfileIndex in rcIgmpFilterTable, the corresponding profile configuration will apply to this vlan. A value of zero indicates no profile is associated with corresponding vlan. The filtering action on each port is also defined by the associated profile." ::= { rcIgmpFilterVlanEntry 2 } rcIgmpFilterVlanMaxGroups OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the max multicast group numbers that allow this vlan join. A value of zero indicates no max limitation is associated with corresponding vlan." DEFVAL { 0 } ::= { rcIgmpFilterVlanEntry 3 } rcIgmpFilterVlanCurrentGroups OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the current multicast group numbers that this vlan has joined." ::= { rcIgmpFilterVlanEntry 4 } rcIgmpFilterVlanMaxGroupsAction OBJECT-TYPE SYNTAX INTEGER { deny(1), replace(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies which action will take place on the vlan when exceed the max multicast group numbers. A value of deny(1) indicates deny join the multicast group when exceed the max multicast group numbers. A value of replace(2) indicates allow to replace the first multicast group on the vlan when exceed the max multicast group numbers." DEFVAL { deny } ::= { rcIgmpFilterVlanEntry 5 } --end MVR group -- END