NETI-ETH-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32, Gauge32, Counter32, Counter64, TimeTicks FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, TimeStamp, TruthValue, RowPointer FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB netiGeneric FROM NETI-COMMON-MIB Dsti FROM NETI-CHMGR-MIB; netiEthMIB MODULE-IDENTITY LAST-UPDATED "201403201000Z" ORGANIZATION "Net Insight AB" CONTACT-INFO "Net Insight AB Box 42093 SE-126 14 Stockholm Sweden Tel +46-8-685 0400 info@netinsight.se" DESCRIPTION "Reference: NID2982 This MIB specifies objects for configuring Ethernet-like services and devices. It models trail termination points (TTPs) for Ethernet Transport Service as virtual interfaces. It also includes objects for configuration of the physical interfaces (ports). 1+1 protected transport is provided using virtual interfaces as interface groups. Physical and logical interfaces are connected to Forwarding Functions. The configuration model consists of the following primary tables: ethDeviceTable. This table contains one entry for every device (board). Its primary function is to provide capability information about the objects such as forwarding functions and interfaces on the device. ethIfTable. Table with all interfaces, both physical (dot3), logical (ETS), and virtual ports as interface group. The table contains an entry for every port. It contains configuration objects common to all port types. ethDot3Table. Table that contains an entry for every physical port. The table holds the data related to the physical port. Note that the port is also represented in the ethIfTable, and is referenced by the same index in both tables. ethEtsTable. Table that contains one entry for every Ethernet Transport Service Trail Termination Point (ETS TTP). A TTP is used to connect a port to a remote port using a connection over the DTM network. Note that the port is also represented in the ethIfTable, and is referenced by the same index in both tables. ethIfgTable. This table contains one entry for every interface group. An interface group is a virtual port that represents the transport over two paths to a remote interface group for 1+1 protected transport. The two paths are implemented using two ports from the ethEtsTable. ethFwdFuncTable. This table contains an entry for every forwarding function. Physical and ETS ports must be associated with a forwarding function. The forwarding function then forwards Ethernet frames between the different associated ports. Configuration objects on the forwarding function and the associated interfaces control how frames are forwarded to the different ports. In addition to the primary tables, there are some other tables: ethFwdDiffservTable. Configuration of differentiated service code points to flow group map for a forwarding function. ethIfQueueTable. Configuration of a port's queues. ethIfQDropThresholdTable. Configuration of drop thresholds for combination of traffic class and drop precedence per interface. ethIfVLANSetsTable. Configuration of a the port's VLAN membership. ethEtsTConnectionTable. References to connections that are terminating in a Trail Termination Point. ethEtsIndexLookupTable. Reverse-lookup of an entry in the ethEtsTable based on known DSTI. The following two tables contains information regarding the Rapid Spanning Tree Protocol: ethFwdRstpTable. The table contains data related to the bridge for the Rapid Spanning Tree Protocol. This table is indexed with the same index as the ethFwdTable. ethIfRstpTable. The table contains data related to the port for the Rapid Spanning Tree Protocol. This table is indexed with the same index as the ethIfTable (and ethDot3Table and ethEtsTable)." REVISION "201403201000Z" DESCRIPTION "Added objects for configuration of MRP MAC address processing: ethFwdMrpAddr0180C2000020 trough ethFwdMrpAddr0180C200002F. Added support for 10 GbE interfaces: - Added b10g(4) to AdvertisedSpeed. - Added new textual convention EthInterfaceType. ethIfType now uses this. - Updated semantics for ethDot3AutoNegotiate. - Added objects to ethDot3Table: ethDot3AutoNegotiateStatus, ethDot3AutoNegotiateAllowed, ethDot3AutoNegotiateMandatory, ethDot3SupportedIfType, ethDot3SelectedIfType. Added objects for extended Class of Service: - Added ethDevCapDropPrecedenceLevels, ethDevDropProbabilityFunctions and ethDevFailure to ethDeviceTable. - Added ethIfMaxMaxQueueFrames, ethIfDefaultDropPrecedence and ethIfDropPrecedenceMap to ethIfTable. - Added table for configuration drop threshold settings, ethIfQDropThresholdTable." REVISION "201302281000Z" DESCRIPTION "Added interface statistics, ethIfStatTable." REVISION "201209121000Z" DESCRIPTION "Added objects to support interface groups and 1+1 protection: - Added ethDevIfgFirstIndex and ethDevIfgNextIndex to ethDeviceTable. - Added ethIfInterfaceGroup to ethIfTable. - Added `bETSGroup(7)' to ethIfType in ethIfTable. - Added ethIfgTable, a table holding interface groups data. - Added ethStatDcap1Table, a table holding counter values. Added error message objects to ethIfTable: ethIfSrcFailure and ethIfSnkFailure. Added object to reset interface to its default settings: ethDot3ResetToDefaults added to ethDot3Table." REVISION "201201271500Z" DESCRIPTION "Added objects that contains the actual value as a result of using auto settings: - Added ethFwdCurrentStpMode to ethFwdFuncTable. - Added ethIfRstpCurrentPathCost to ethIfRstpTable." REVISION "201110260900Z" DESCRIPTION "Updated some descriptions." REVISION "201109051100Z" DESCRIPTION "Reference: NID2982PA39. Added objects for minor level of Reduced Bit Rate alarm: ethIfSrcMinorReducedBitRateThreshold, ethIfSnkMinorReducedBitRateThreshold, ethIfSrcMinorReducedBitRateHighThreshold, ethIfSnkMinorReducedBitRateHighThreshold. Added objects for configuration of reserved MAC address processing: ethFwdReservedAddr0180C2000002 trough ethFwdReservedAddr0180C200000F." REVISION "201010201600Z" DESCRIPTION "Reference: NID2982PA33. Added objects for fault management: ethFwdPropagateFaults, ethIfSrcDegThreshold, ethIfSnkDegThreshold, ethIfSrcDegPeriod, ethIfSnkDegPeriod, ethIfSrcReducedBitRateThreshold, ethIfSnkReducedBitRateThreshold, ethIfSrcReducedBitRateHighThreshold, ethIfSnkReducedBitRateHighThreshold, ethIfSrcReducedBitRateAIS, ethIfSnkReducedBitRateAIS, ethIfSnkDegAIS, ethEtsSnkExpectChannel. Added capability object for fault management: ethDevCapConfigurableFaultMgmt. Added objects for referencing performance monitoring: ethIfSrcPmReference, ethIfSnkPmReference. Added capability object for performance monitoring: ethDevCapPerformanceMonitoring." REVISION "200907081200Z" DESCRIPTION "First stable release." ::= { netiGeneric 2 } -- -- Textual Conventions -- TrafficClass ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A traffic class." SYNTAX Integer32 (0..7) VLANSet ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x" STATUS current DESCRIPTION "A set of VLAN ids. The octet string represents a bit array where each bit represents a VLAN id. If the bit is set, then the VLAN id is included in the set. VLANs are identified from left to right, where the leftmost bit in octet 1 is VLAN id 0 and the rightmost bit in octet 512 represents VLAN id 4095. (Note that VLAN id 0 and 4095 are invalid VLAN ids and these bits shall always be 0). Example: The VLAN ids 4-8, 15, 16, 23, 42 are represented by the octet string starting with the following octets (in hex): 0f8181000020..." SYNTAX OCTET STRING (SIZE(512)) AdvertisedSpeed ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "auto(0). If auto-negotiation is enabled (see ethDot3AutoNegotiate), then advertise all speeds that the device supports. If auto auto-negotiation is disabled, then use the highest speed that the device supports. b10(1). Advertise that the interface supports 10 Mbps. b100(2). Advertise that the interface supports 100 Mbps. b1000(3). Advertise that the interface supports 1 Gbps. b10g(4). Advertise that the interface supports 10 Gbps." SYNTAX BITS { auto(0), b10(1), b100(2), b1000(3), b10g(4) } AdvertisedDuplex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "auto(0). If auto-negotiation is enabled (see ethDot3AutoNegotiation), then advertise all duplex that the device supports. If auto-negotiation is disabled, then use full duplex. fullDuplex(1). Advertise that the interface supports full duplex. halfDuplex(2). Advertise that the interface supports half duplex. If auto-negotiation is disabled, then use maximum duplex set." SYNTAX BITS { auto(0), fullDuplex(1), halfDuplex(2) } AdvertisedFlowControl ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "auto(0). Advertise all settings that the port supports. This bit cannot be set at the same time as when any of the other bits are set. Setting this bit will clear the other bits. If auto-negotiation is disabled (see ethDot3AutoNegotiate), then `auto(0)' means that flow control is enabled in both directions. pause(1). Advertise PAUSE. asmDir(2). Advertise ASM_DIR." SYNTAX BITS { auto(0), pause(1), asmDir(2) } BridgeIdentifier ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x:" STATUS current DESCRIPTION "The Bridge-Identifier, as used in the Rapid Spanning Tree Protocol (RSTP), to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value, and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge)." SYNTAX OCTET STRING(SIZE (8)) EthInterfaceType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of interface. The value `unknown(1)' is presented if required hardware is missing, or if it otherwise is not possible to determined the type of interface." SYNTAX INTEGER { auto(0), unknown(1), bETS(2), b100baseTX(3), b1000baseSX(4), b1000baseLX(5), b1000baseT(6), bETSGroup(7), b10GbaseSR(8), b10GbaseLR(9), b10GbaseLRM(10), b10GbaseER(11), b10GbaseZR(12) } PortIdentifier ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Port-Identifier, as used in the Rapid Spanning Tree Protocol (RSTP), to uniquely identify the port within the bridge. Its first octet (in network byte order) contains a priority value, and the second octet contains the Port Number." SYNTAX OCTET STRING(SIZE (2)) Timeout ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A Rapid Spanning Tree Protocol (RSTP) timer in units of 1/100 seconds. Several objects in this MIB module represent values of timers used by the Rapid Spanning Tree Protocol. In this MIB, these timers have values in units of hundredths of a second (i.e., 1/100 seconds)." SYNTAX Integer32 FrameProcess ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Describes how a frame shall be processed: notSupported(0). setting of this value is not supported by the device. drop(1). Frames are dropped. forward(2). Frames are forwarded." SYNTAX INTEGER { notSupported(0), drop(1), forward(2) } InterfaceIndexList ::= TEXTUAL-CONVENTION DISPLAY-HINT "4d," STATUS current DESCRIPTION "A list of interfaces as ethIfIndex. Each group of 4 octets represents the value of an ethIfIndex." SYNTAX OCTET STRING IfgProtectionStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Describes the protection status of a protected service in an interface group. unavailable(1). means that neither channel is up. unprotected(2). means that one of the channels is up. standbyProtected(3). means that both channels are up and if the active channel detects AIS, a failover will occur while incurring a hit. hitlessCapable(4). means that the differential delay is within limit, but a buffer reset is required to reach hitless protected state. This can be achieved by writing the forceHit parameter. hitlessProtected(5). means that either channel can go down without incurring a data loss. " SYNTAX INTEGER { unavailable(1), unprotected(2), standbyProtected(3), hitlessCapable(4), hitlessProtected(5) } -- -- Objects in the NETI-ETH-MIB -- ethObjects OBJECT IDENTIFIER ::= { netiEthMIB 1 } ethDeviceGroup OBJECT IDENTIFIER ::= { ethObjects 1 } ethFwdFuncGroup OBJECT IDENTIFIER ::= { ethObjects 2 } ethInterfaceGroup OBJECT IDENTIFIER ::= { ethObjects 3 } ethStatisticsGroup OBJECT IDENTIFIER ::= { ethObjects 4 } -- -- Devices -- -- Device table ethDeviceTable OBJECT-TYPE SYNTAX SEQUENCE OF EthDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table that represents Ethernet capable devices. The table is automatically populated with entries representing all mounted Ethernet devices." ::= { ethDeviceGroup 1 } ethDeviceEntry OBJECT-TYPE SYNTAX EthDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing one device (board)." INDEX { ethDevIndex } ::= { ethDeviceTable 1 } EthDeviceEntry ::= SEQUENCE { ethDevIndex Unsigned32, ethDevRowStatus RowStatus, ethDevName SnmpAdminString, ethDevContainerName SnmpAdminString, ethDevProductName SnmpAdminString, ethDevStatus INTEGER, ethDevCapJumboFrames BITS, ethDevCapMaxAgingTime Unsigned32, ethDevCapMACMode BITS, ethDevCapSpanningTree BITS, ethDevCapVLANMode BITS, ethDevCapAdvertisedDuplex AdvertisedDuplex, ethDevCapAdvertisedFlowControl AdvertisedFlowControl, ethDevCapAcceptableFrameType BITS, ethDevCapDefaultEthernetPriority OCTET STRING, ethDevCapLearning BITS, ethDevCapTransmittedFrameTypeETS BITS, ethDevCapTransmittedFrameTypeDot3 BITS, ethDevCapMaxMaxQueueOctets Unsigned32, ethDevCapMaxMaxQueueFrames Unsigned32, ethDevCapMaxTrafficClass TrafficClass, ethDevEtsNextIndex Unsigned32, ethDevFwdFuncNextIndex Unsigned32, ethDevCapPerformanceMonitoring INTEGER, ethDevCapConfigurableFaultMgmt INTEGER, ethDevIfgFirstIndex Unsigned32, ethDevIfgNextIndex Unsigned32, ethDevCapDropPrecedenceLevels Unsigned32, ethDevCapDropProbabilityFunctions BITS, ethDevFailure SnmpAdminString } ethDevIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index in the table. The index is equal to the board position in the node. The index is maintained across reboots of the managed system." ::= { ethDeviceEntry 1 } ethDevRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The following values are supported: active(1). The object always reads active. destroy(6). All configurations for the device are deleted. If the physical device exists, then a new default configuration will be created for the device. If the physical device does not exist, then the configuration is deleted. If a physical device is inserted into the node, then a new default configuration will be created for the device." ::= { ethDeviceEntry 2 } ethDevName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name of the device. The value of this object should be the name of the device as assigned by the local device and should be suitable for use in commands entered at the device's `console'." ::= { ethDeviceEntry 3 } ethDevContainerName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the container where the physical device is mounted." ::= { ethDeviceEntry 4 } ethDevProductName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the product. The value of this object should be the name of the device as printed on the front panel or similar." ::= { ethDeviceEntry 5 } ethDevStatus OBJECT-TYPE SYNTAX INTEGER { present(1), absent(2), mismatch(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the device, indicating if the board is plugged in or not. present(1). The device is present and functional. absent(2). The device is not present. mismatch(3). A device is present on the location representing the configuration but the device is not compatible with the stored configuration." ::= { ethDeviceEntry 6 } ethDevCapJumboFrames OBJECT-TYPE SYNTAX BITS { on(0), off(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Jumbo Frames capabilities of forwarding functions on the device. Describes all supported values of the Jumbo Frames setting. See ethFwdJumboFrames." ::= { ethDeviceEntry 7 } ethDevCapMaxAgingTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum aging time for dynamically learned forwarding information for forwarding functions on the device. Zero (0) if the device does not allow the value to be set. See ethFwdAgingTime." ::= { ethDeviceEntry 8 } ethDevCapMACMode OBJECT-TYPE SYNTAX BITS { auto(0), mac(1), nomac(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC mode capabilities of forwarding functions on the device. Describes all supported values of the MAC modes setting. See ethFwdMACMode." ::= { ethDeviceEntry 9 } ethDevCapSpanningTree OBJECT-TYPE SYNTAX BITS { auto(0), forward(1), drop(2), process(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The spanning tree capabilities of forwarding functions on the device. Describes all supported values of the spanning tree settings. If spanning tree is not supported, then the value is `forward(1)'. See ethFwdSpanningTree." ::= { ethDeviceEntry 10 } ethDevCapVLANMode OBJECT-TYPE SYNTAX BITS { transparent(0), customer(1), provider(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN mode capabilities of forwarding functions on the device. Describes all supported values of the VLAN mode settings. See ethFwdVLANMode." ::= { ethDeviceEntry 11 } ethDevCapAdvertisedDuplex OBJECT-TYPE SYNTAX AdvertisedDuplex MAX-ACCESS read-only STATUS current DESCRIPTION "Supported values for the duplex setting of a physical interface on the device. See dot3AdvertisedDuplex." ::= { ethDeviceEntry 12 } ethDevCapAdvertisedFlowControl OBJECT-TYPE SYNTAX AdvertisedFlowControl MAX-ACCESS read-only STATUS current DESCRIPTION "Supported values for the flow control setting of a physical interface on the device. See dot3AdvertisedFlowControl." ::= { ethDeviceEntry 13 } ethDevCapAcceptableFrameType OBJECT-TYPE SYNTAX BITS { all(0), vlanTagged(1), untagged(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The frame types capabilities of interfaces on the device. Describes all supported values of the acceptable frame type setting. See ethIfAcceptableFrameTypes." ::= { ethDeviceEntry 14 } ethDevCapDefaultEthernetPriority OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The range of allowed values for Ethernet priority of interfaces on the device. See ethIfDefaultEthernetPriority. The object consists of two octets, where the first octet represents the lowest allowed value and the second octet represents the highest allowed value." ::= { ethDeviceEntry 15 } ethDevCapLearning OBJECT-TYPE SYNTAX BITS { on(0), off(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The learning capabilities of forwarding functions on the device. Describes all supported values of the learning setting. See ethIfLearning." ::= { ethDeviceEntry 16 } ethDevCapTransmittedFrameTypeETS OBJECT-TYPE SYNTAX BITS { vlanTagged(1), untagged(2), legacy(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The allowed values of the transmitted frame type on an Ethernet Transport Service Trail Termination Point, ETS TTP. See ethIfTransmittedFrameType. Note that the interface type can be determined by examine ethIfType." ::= { ethDeviceEntry 17 } ethDevCapTransmittedFrameTypeDot3 OBJECT-TYPE SYNTAX BITS { vlanTagged(1), untagged(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The allowed values of the transmitted frame type on an dot3 interface. See ethIfTransmittedFrameType. Note that the interface type can be determined by examine ethIfType." ::= { ethDeviceEntry 18 } ethDevCapMaxMaxQueueOctets OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value in octets possible to set for the maximum queue size for queues on the device. See ethIfQueueMaxOctets." ::= { ethDeviceEntry 19 } ethDevCapMaxMaxQueueFrames OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The maximum value in frames allowed to set for the maximum queue size for queues on the device. See ethIfQueueMaxFrames." ::= { ethDeviceEntry 20 } ethDevCapMaxTrafficClass OBJECT-TYPE SYNTAX TrafficClass MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of traffic classes supported by the device. Traffic classes are identified by numbers starting from 0 to, but not including, this value." ::= { ethDeviceEntry 21 } ethDevEtsNextIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the next available index (ethIfIndex) in the ethEtsTable for this device." ::= { ethDeviceEntry 22 } ethDevFwdFuncNextIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the next available index (ethFwdIndex) in the ethFwdFuncTable for this device." ::= { ethDeviceEntry 23 } ethDevCapPerformanceMonitoring OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates how the device supports performance monitoring." ::= { ethDeviceEntry 24 } ethDevCapConfigurableFaultMgmt OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates how the device supports configurable fault management." ::= { ethDeviceEntry 25 } ethDevIfgFirstIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the first allowed index (ethIfIndex) in the ethIfgTable for this device." ::= { ethDeviceEntry 26 } ethDevIfgNextIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the next available index (ethIfIndex) in the ethIfgTable for this device." ::= { ethDeviceEntry 27 } ethDevCapDropPrecedenceLevels OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of different drop precedence (DP) levels that this devices supports. The DP levels are numbered from 0 to (dropPrecedenceLevels - 1)" ::= { ethDeviceEntry 28 } ethDevCapDropProbabilityFunctions OBJECT-TYPE SYNTAX BITS { taildrop(0), wred(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The drop probability functions supported for this device." ::= { ethDeviceEntry 29 } ethDevFailure OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A string describing the configuration or error status of the device. The string is the empty string if the configuration is correct, otherwise a message describing the error." ::= { ethDeviceEntry 30 } -- -- Forwarding Function -- ethFwdFuncLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when status or configuration of any the objects in the ethFwdFuncTable or ethFwdDiffservTable was last changed." ::= { ethFwdFuncGroup 1 } -- Forwarding Function Table ethFwdFuncTable OBJECT-TYPE SYNTAX SEQUENCE OF EthForwardingFunctionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of forwarding functions." ::= { ethFwdFuncGroup 2 } ethFwdFuncEntry OBJECT-TYPE SYNTAX EthForwardingFunctionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing one forwarding function." INDEX { ethDevIndex, ethFwdIndex } ::= { ethFwdFuncTable 1 } EthForwardingFunctionEntry ::= SEQUENCE { ethFwdIndex Integer32, ethFwdRowStatus RowStatus, ethFwdName SnmpAdminString, ethFwdCustomerId Unsigned32, ethFwdPurpose SnmpAdminString, ethFwdJumboFrames INTEGER, ethFwdMACMode INTEGER, ethFwdCurrentMACMode INTEGER, ethFwdSpanningTree INTEGER, ethFwdVLANMode INTEGER, ethFwdAgingTime Unsigned32, ethFwdFailure SnmpAdminString, ethFwdLastChange TimeTicks, ethFwdPropagateFaults TruthValue, ethFwdReservedAddr0180C2000002 FrameProcess, ethFwdReservedAddr0180C2000003 FrameProcess, ethFwdReservedAddr0180C2000004 FrameProcess, ethFwdReservedAddr0180C2000005 FrameProcess, ethFwdReservedAddr0180C2000006 FrameProcess, ethFwdReservedAddr0180C2000007 FrameProcess, ethFwdReservedAddr0180C2000008 FrameProcess, ethFwdReservedAddr0180C2000009 FrameProcess, ethFwdReservedAddr0180C200000A FrameProcess, ethFwdReservedAddr0180C200000B FrameProcess, ethFwdReservedAddr0180C200000C FrameProcess, ethFwdReservedAddr0180C200000D FrameProcess, ethFwdReservedAddr0180C200000E FrameProcess, ethFwdReservedAddr0180C200000F FrameProcess, ethFwdCurrentStpMode INTEGER, ethFwdMrpAddr0180C2000020 FrameProcess, ethFwdMrpAddr0180C2000021 FrameProcess, ethFwdMrpAddr0180C2000022 FrameProcess, ethFwdMrpAddr0180C2000023 FrameProcess, ethFwdMrpAddr0180C2000024 FrameProcess, ethFwdMrpAddr0180C2000025 FrameProcess, ethFwdMrpAddr0180C2000026 FrameProcess, ethFwdMrpAddr0180C2000027 FrameProcess, ethFwdMrpAddr0180C2000028 FrameProcess, ethFwdMrpAddr0180C2000029 FrameProcess, ethFwdMrpAddr0180C200002A FrameProcess, ethFwdMrpAddr0180C200002B FrameProcess, ethFwdMrpAddr0180C200002C FrameProcess, ethFwdMrpAddr0180C200002D FrameProcess, ethFwdMrpAddr0180C200002E FrameProcess, ethFwdMrpAddr0180C200002F FrameProcess } ethFwdIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index representing the forwarding function on the device." ::= { ethFwdFuncEntry 1 } ethFwdRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "See SNMPv2-TC. The maximum number of forwarding functions is limited by the type of device. This is described per device in ethDevCapMaxForwardingFunctions. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new forwarding function. destroy(6). The forwarding function is deleted. All interfaces that belonged to the deleted forwarding function will no longer belong to any forwarding function, see ethIfForwardingFunction." ::= { ethFwdFuncEntry 2 } ethFwdName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name of the forwarding function. The value of this object should be suitable for use in commands entered at the device's `console'." ::= { ethFwdFuncEntry 3 } ethFwdCustomerId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "An identification number representing the customer or user using the forwarding function. The value could be used for e.g. Charge Data Records. The value zero (0) indicates that no specific customer is associated with the forwarding function." DEFVAL { 0 } ::= { ethFwdFuncEntry 4 } ethFwdPurpose OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A string representing the purpose of the forwarding function. The string is for administrative purpose." DEFVAL { ''H } ::= { ethFwdFuncEntry 5 } ethFwdJumboFrames OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies how the forwarding function shall handle Jumbo frames: on(1). Jumbo frames are forwarded as any standard Ethernet frame. off(2). Jumbo frames are discarded upon reception. See ethDevCapJumboFrames for accepted values." DEFVAL { on } ::= { ethFwdFuncEntry 6 } ethFwdMACMode OBJECT-TYPE SYNTAX INTEGER { auto(1), mac(2), nomac(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies how the forwarding function shall handle unicast frames when it does not know what interface to use for reaching a destination. auto(1). Equivalent to `mac(2)' if the forwarding function is connected to at least three interfaces, otherwise equivalent to `nomac(3)'. If the device does not support `mac(2)', then `auto(1)' is always equivalent to `nomac(3)'. mac(2). The forwarding function will learn what interfaces to use for a destination. This is done by looking at the source MAC address on received frames. When the forwarding function has learned what interface to use, it will forward the frame on that interface only. Learning is also specified for each interface and traffic class with ethIfQueueLearning. nomac(3). The forwarding function will forward the frame on all its interfaces." DEFVAL { auto } ::= { ethFwdFuncEntry 7 } ethFwdCurrentMACMode OBJECT-TYPE SYNTAX INTEGER { mac(2), nomac(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Describes the currently active MAC mode, see ethFwdMACMode." ::= { ethFwdFuncEntry 8 } ethFwdSpanningTree OBJECT-TYPE SYNTAX INTEGER { auto(1), forward(2), drop(3), process(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "auto(1). If the device does not implement the spanning-tree protocol, or if exactly two interfaces are connected to the forwarding function, then it will act as if `forward(2)' has been specified. Otherwise, it will act as if `process(4)' has been specified. forward(2). Received spanning-tree messages are broadcasted to all interfaces except the interface where the message was received. No further processing is done. drop(3). Received spanning-tree messages are dropped without any further processing. process(4). Received spanning-tree messages are processed according to the spanning-tree protocol." DEFVAL { auto } ::= { ethFwdFuncEntry 9 } ethFwdVLANMode OBJECT-TYPE SYNTAX INTEGER { transparent(1), customer(2), provider(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "transparent(1). Ignore VLAN tags on received frames. VLAN tags are not added nor removed from the frames. If a frame has a VLAN tag, then it is retained. If a frame does not have a VLAN tag, then no tag is added. customer(2). VLAN-handling in accordance with IEEE 802.1Q. Frames are forwarded and filtered according to customer VLAN tag. Frames that are not tagged are tagged with default VLAN tag as configured on the interface. provider(3). VLAN-handling in accordance with IEEE 802.1ad. Frames are forwarded and filtered according to service VLAN tag. Any customer VLAN is ignored. Frames that are not tagged are tagged with default VLAN tag as configured on the interface." DEFVAL { transparent } ::= { ethFwdFuncEntry 10 } ethFwdAgingTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The timeout period in seconds for aging out dynamically learned forwarding information. The value 0 means that aging is disabled and that the learned entries are not removed from the lookup table. See ethDevCapMaxAgingTime for maximum value." DEFVAL { 300 } ::= { ethFwdFuncEntry 11 } ethFwdFailure OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A string describing the configuration or error status of the forwarding function. The string is the empty string if the configuration is correct, otherwise a message describing the error." ::= { ethFwdFuncEntry 12 } ethFwdLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time when the operational state or any configuration was last changed on this forwarding function." ::= { ethFwdFuncEntry 13 } ethFwdPropagateFaults OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Propagate faults to all interfaces belonging to this forwarding function." DEFVAL { false } ::= { ethFwdFuncEntry 14 } ethFwdReservedAddr0180C2000002 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 15 } ethFwdReservedAddr0180C2000003 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 16 } ethFwdReservedAddr0180C2000004 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 17 } ethFwdReservedAddr0180C2000005 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 18 } ethFwdReservedAddr0180C2000006 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 19 } ethFwdReservedAddr0180C2000007 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 20 } ethFwdReservedAddr0180C2000008 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 21 } ethFwdReservedAddr0180C2000009 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 22 } ethFwdReservedAddr0180C200000A OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 23 } ethFwdReservedAddr0180C200000B OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 24 } ethFwdReservedAddr0180C200000C OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 25 } ethFwdReservedAddr0180C200000D OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 26 } ethFwdReservedAddr0180C200000E OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 27 } ethFwdReservedAddr0180C200000F OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process reserved MAC address." REFERENCE "IEEE 802.1D-2004: clause 7.12.6" DEFVAL { drop } ::= { ethFwdFuncEntry 28 } ethFwdCurrentStpMode OBJECT-TYPE SYNTAX INTEGER { forward(2), drop(3), process(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current STP mode as, as a result of the configured value in ethFwdSpanningTree. Unless ethFwdSpannigTree is `auto(1), then this always reads the same value as that object." ::= { ethFwdFuncEntry 29 } ethFwdMrpAddr0180C2000020 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 30 } ethFwdMrpAddr0180C2000021 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 31 } ethFwdMrpAddr0180C2000022 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 32 } ethFwdMrpAddr0180C2000023 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 33 } ethFwdMrpAddr0180C2000024 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 34 } ethFwdMrpAddr0180C2000025 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 35 } ethFwdMrpAddr0180C2000026 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 36 } ethFwdMrpAddr0180C2000027 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 37 } ethFwdMrpAddr0180C2000028 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 38 } ethFwdMrpAddr0180C2000029 OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 39 } ethFwdMrpAddr0180C200002A OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 40 } ethFwdMrpAddr0180C200002B OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 41 } ethFwdMrpAddr0180C200002C OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 42 } ethFwdMrpAddr0180C200002D OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 43 } ethFwdMrpAddr0180C200002E OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 44 } ethFwdMrpAddr0180C200002F OBJECT-TYPE SYNTAX FrameProcess MAX-ACCESS read-write STATUS current DESCRIPTION "Configuration of how to process Multiple Registration Protocol (MRP) MAC address." REFERENCE "IEEE 802.1Q-2011: clause 10.5" DEFVAL { forward } ::= { ethFwdFuncEntry 45 } -- End of Forwarding Function table -- Differentiated Services Code Point to Flow Group Map ethFwdDiffservTable OBJECT-TYPE SYNTAX SEQUENCE OF EthFwdDiffservEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table maps differentiated service code points (DSCP) to flow groups." ::= { ethFwdFuncGroup 3 } ethFwdDiffservEntry OBJECT-TYPE SYNTAX EthFwdDiffservEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry represents the mapping of one DSCP to one flow group for an interface." INDEX { ethDevIndex, ethFwdIndex, ethFwdDiffservIndex } ::= { ethFwdDiffservTable 1 } EthFwdDiffservEntry ::= SEQUENCE { ethFwdDiffservIndex Integer32, ethFwdDiffservFlowGroup Integer32 } ethFwdDiffservIndex OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index representing the differentiated service code point (DSCP). For each forwarding function, the table contains 64 rows, numbered from 0 to 63 representing DSCP bit pattern '000000' through '111111'." ::= { ethFwdDiffservEntry 1 } ethFwdDiffservFlowGroup OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies which flow group that the differentiated service code point (DSCP) shall be mapped to." DEFVAL { 0 } ::= { ethFwdDiffservEntry 2 } -- Rapid Spanning Tree Protocol Bridge Table ethFwdRstpTable OBJECT-TYPE SYNTAX SEQUENCE OF EthFwdRstpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains Rapid Spanning Tree Protocol (RSTP) specific configurations and data for forwarding functions. If a forwarding function does not support RSTP, then the table will not hold an entry for that forwarding function." ::= { ethFwdFuncGroup 4 } ethFwdRstpEntry OBJECT-TYPE SYNTAX EthFwdRstpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry represents Rapid Spanning Tree Protocol (RSTP) related data for one forwarding function." INDEX { ethDevIndex, ethFwdIndex } ::= { ethFwdRstpTable 1 } EthFwdRstpEntry ::= SEQUENCE { ethFwdRstpBridgeIdentifier BridgeIdentifier, ethFwdRstpPriority Integer32, ethFwdRstpTimeSinceTopologyChange Timeout, ethFwdRstpTopologyChangeCount Counter32, ethFwdRstpTopologyChange TruthValue, ethFwdRstpDesignatedRoot BridgeIdentifier, ethFwdRstpRootPathCost Integer32, ethFwdRstpRootPortName SnmpAdminString, ethFwdRstpMaxAge Timeout, ethFwdRstpHelloTime Timeout, ethFwdRstpForwardDelay Timeout, ethFwdRstpBridgeMaxAge Timeout, ethFwdRstpBridgeHelloTime Timeout, ethFwdRstpBridgeForwardDelay Timeout, ethFwdRstpTxHoldCount Integer32, ethFwdRstpForceVersion INTEGER } ethFwdRstpBridgeIdentifier OBJECT-TYPE SYNTAX BridgeIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The unique identifier for this bridge." REFERENCE "IEEE 802.1D-2004: clause 14.8.1.1.3." ::= { ethFwdRstpEntry 1 } ethFwdRstpPriority OBJECT-TYPE SYNTAX Integer32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The local bridge priority. The value must be set in increments of 4096." REFERENCE "IEEE 802.1D-2004: clause 17.14." DEFVAL { 32768 } ::= { ethFwdRstpEntry 2 } ethFwdRstpTimeSinceTopologyChange OBJECT-TYPE SYNTAX Timeout UNITS "centi-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in 1/100 seconds since the last topology change." REFERENCE "IEEE 802.1D-2004: clause 14.8.1.1.3." ::= { ethFwdRstpEntry 3 } ethFwdRstpTopologyChangeCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of topology changes detected by this bridge since the management entity was last reset or initialized." REFERENCE "IEEE 802.1D-2004: clause 14.8.1.1.3." ::= { ethFwdRstpEntry 4 } ethFwdRstpTopologyChange OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Set to `true(1)' when a topology change is in progress." REFERENCE "IEEE 802.1D-2004: clause 14.8.1.1.3." ::= { ethFwdRstpEntry 5 } ethFwdRstpDesignatedRoot OBJECT-TYPE SYNTAX BridgeIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the root of the spanning tree, as determined by the Spanning Tree Protocol, as executed by this bridge. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node." REFERENCE "IEEE 802.1D-2004: clause 14.8.1.1.3." ::= { ethFwdRstpEntry 6 } ethFwdRstpRootPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the root as seen from this bridge." REFERENCE "IEEE 802.1D-2004: clause 14.8.1.1.3." ::= { ethFwdRstpEntry 7 } ethFwdRstpRootPortName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the interface that offers the lowest cost path from this bridge to the root bridge." REFERENCE "IEEE 802.1D-2004: clause 14.8.1.1.3." ::= { ethFwdRstpEntry 8 } ethFwdRstpMaxAge OBJECT-TYPE SYNTAX Timeout UNITS "centi-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using." REFERENCE "IEEE 802.1D-2004: clause 17.18.7." ::= { ethFwdRstpEntry 9 } ethFwdRstpHelloTime OBJECT-TYPE SYNTAX Timeout UNITS "centi-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree, or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using." REFERENCE "IEEE 802.1D-2004: clause 17.18.7." ::= { ethFwdRstpEntry 10 } ethFwdRstpForwardDelay OBJECT-TYPE SYNTAX Timeout UNITS "centi-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The root bridge forward delay parameter, in units of hundredths of a second." REFERENCE "IEEE 802.1D-2004: clause 17.18.7." ::= { ethFwdRstpEntry 11 } ethFwdRstpBridgeMaxAge OBJECT-TYPE SYNTAX Timeout (600..4000) UNITS "centi-seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value that all bridges use for MaxAge when this bridge is acting as the root. An agent may return a badValue error if a set is attempted to a value that is not a whole number of seconds, or it may truncate the value to a whole number of seconds." REFERENCE "IEEE 802.1D-2004: clause 17.13.8 and 17.14." DEFVAL { 2000 } ::= { ethFwdRstpEntry 12 } ethFwdRstpBridgeHelloTime OBJECT-TYPE SYNTAX Timeout (100..200) UNITS "centi-seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value that all bridges use for HelloTime when this bridge is acting as the root. An agent may return a badValue error if a set is attempted to a value that is not a whole number of seconds, or it may truncate the value to a whole number of seconds." REFERENCE "IEEE 802.1D-2004: clause 17.13.6 and 17.14." DEFVAL { 200 } ::= { ethFwdRstpEntry 13 } ethFwdRstpBridgeForwardDelay OBJECT-TYPE SYNTAX Timeout (400..3000) MAX-ACCESS read-write STATUS current DESCRIPTION "The value that all bridges use for ForwardDelay when this bridge is acting as the root. An agent may return a badValue error if a set is attempted to a value that is not a whole number of seconds, or it may truncate the value to a whole number of seconds." REFERENCE "IEEE 802.1D-2004: clause 17.13.5 and 17.14." DEFVAL { 1500 } ::= { ethFwdRstpEntry 14 } ethFwdRstpTxHoldCount OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The local bridge transmit hold count parameter." REFERENCE "IEEE 802.1D-2004: clause 17.13.12 and 17.14." DEFVAL { 6 } ::= { ethFwdRstpEntry 15 } ethFwdRstpForceVersion OBJECT-TYPE SYNTAX INTEGER { stp(1), rstp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Force the spanning tree protocol version to use for this bridge: stp(1). STP compatibility mode. Causes an RSTP Bridge to use STP compatible BPDUs and timer values on all Bridge Ports. Rapid transitions are disabled, supporting applications and protocols that are particularly sensitive to frame duplication and misordering. rstp(2). Normal mode" REFERENCE "IEEE 802.1D-2004: clause 17.13.4 and 17.4." DEFVAL { rstp } ::= { ethFwdRstpEntry 16 } -- End of Rapid Spanning Tree Protocol Bridge Table --- --- Interfaces --- ethIfGroupLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when status or configuration of any the objects in this group was last changed." ::= { ethInterfaceGroup 1 } -- Interface base table ethIfTable OBJECT-TYPE SYNTAX SEQUENCE OF EthIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing all interfaces, both physical, logical for use with Ethernet Transport Service, and interface groups for use with 1+1 protection." ::= { ethInterfaceGroup 2 } ethIfEntry OBJECT-TYPE SYNTAX EthIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing one interface or interface group. If the interface is a physical interface, a conceptual row also exists for the interface in the ethDot3Table. The management system ensures that all physical interfaces on the device are represented in the table, e.g. by allocating the first number of rows for the physical ports. If the interface is an Ethernet Transport Service Trail Termination Points (ETS TTPs), a conceptual row for the interface also exists in the ethEtsTable. Such interfaces can be created and deleted from that table, and will be reflected in this table. If the interface is an interface group, a conceptual row for the interface also exists in the ethIfgTable. An interface group can be created and deleted from that table, and will be reflected in this table. If the interface group has no member interfaces, then all its objects in this table are read-only." INDEX { ethDevIndex, ethIfIndex } ::= { ethIfTable 1 } EthIfEntry ::= SEQUENCE { ethIfIndex Unsigned32, ethIfIfIndex Integer32, ethIfName SnmpAdminString, ethIfType INTEGER, ethIfCustomerId Unsigned32, ethIfPurpose SnmpAdminString, ethIfAdminStatus INTEGER, ethIfOperStatus INTEGER, ethIfFailure SnmpAdminString, ethIfForwardingFunction Integer32, ethIfAcceptableFrameTypes INTEGER, ethIfTransmittedFrameType INTEGER, ethIfDefaultVLAN Integer32, ethIfDefaultEthernetPriority Integer32, ethIfPriorityMode INTEGER, ethIfDefaultTrafficClass TrafficClass, ethIfFlowGroupMap OCTET STRING, ethIfLearning INTEGER, ethIfInSpeed Gauge32, ethIfInHighSpeed Gauge32, ethIfOutSpeed Gauge32, ethIfOutHighSpeed Gauge32, ethIfVLANNextIndex Unsigned32, ethIfLastChange TimeTicks, ethIfSrcPmReference RowPointer, ethIfSnkPmReference RowPointer, ethIfSrcDegThreshold Unsigned32, ethIfSnkDegThreshold Unsigned32, ethIfSrcDegPeriod Unsigned32, ethIfSnkDegPeriod Unsigned32, ethIfSrcReducedBitRateThreshold Unsigned32, ethIfSnkReducedBitRateThreshold Unsigned32, ethIfSrcReducedBitRateHighThreshold Unsigned32, ethIfSnkReducedBitRateHighThreshold Unsigned32, ethIfSrcReducedBitRateAIS TruthValue, ethIfSnkReducedBitRateAIS TruthValue, ethIfSnkDegAIS TruthValue, ethIfSrcMinorReducedBitRateThreshold Unsigned32, ethIfSnkMinorReducedBitRateThreshold Unsigned32, ethIfSrcMinorReducedBitRateHighThreshold Unsigned32, ethIfSnkMinorReducedBitRateHighThreshold Unsigned32, ethIfSrcFailure SnmpAdminString, ethIfSnkFailure SnmpAdminString, ethIfInterfaceGroup Integer32, ethIfMaxMaxQueueFrames Unsigned32, ethIfDefaultDropPrecedence Unsigned32, ethIfDropPrecedenceMap OCTET STRING } ethIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index for the interface. The index is maintained across restarts of the managed system. The management system may require that the value of this object is within a certain value range depending of the type of interface. If the interface is a physical interface, the index matches the port number as printed on the front of the device. The management system allocates and assigns necessary indices for the physical ports. If the interface represents an ETS TTP, then the value of this is provided when the conceptual row is created. The management system may require the value to be within a range allocated for ETS TTPs. This would be a value larger than the highest physical port number, and lower than the value range reserved for interface groups. The next available index in this range can be retrieved from ethDevEtsNextIndex. If the interface represents an interface group, then the value of this is provided with the conceptual row is created. The management system may require the value to be within a range allocated for interface groups. This would be a value larger than or equal to the value of ethDevIfgFirstIndex. The next available index can be retrieved from ethDevIfgNextIndex." ::= { ethIfEntry 1 } ethIfIfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable uniquely identifies the interface in the ifTable. The value is 0 if the interface is not present in the ifTable." REFERENCE "RFC 2863, ifIndex" ::= { ethIfEntry 2 } ethIfName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the interface. If the interface is a physical interface, it is named `eth:' where is the value of ethDevIndex, and is the value of ethIfIndex. If the interface is an Ethernet Transport Service Trail Termination Point (ETS TTP), then the interface is named `ets:'." ::= { ethIfEntry 3 } ethIfType OBJECT-TYPE SYNTAX EthInterfaceType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of interface. The value `unknown(1)' is presented if required hardware is missing, or if it otherwise is not possible to determined the type of interface." ::= { ethIfEntry 4 } ethIfCustomerId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "An identification number representing the customer or user using the interface. The value could be used for e.g. Charge Data Records. The value zero (0) indicates that no specific customer is associated with the interface." DEFVAL { 0 } ::= { ethIfEntry 5 } ethIfPurpose OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "A string representing the purpose of the interface. The string is for administrative purpose." DEFVAL { ''H } ::= { ethIfEntry 6 } ethIfAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative state of the interface. If the interface represents a Ethernet Transport Service Trail Termination Point (ETS TTP), then the variable controls the desired state of the connections. up(1). The interface shall be enabled. down(2). The interface shall be disabled." DEFVAL { down } ::= { ethIfEntry 7 } ethIfOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), dormant(5), notPresent(6), partial(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The actual operational state of the interface. The value should normally follow the administrative state (ethIfAdminStatus). up(1). The interface is up and operational. If the interface is representing a unicast ETS TTP, then both the originating and terminating connections have been established. For a multicast type, the originating connection has been established to all the configured destinations. Note that a multicast ETS TTP does not require terminating connections to be operational. If the interface is representing an interface group, then the operational status of all member interfaces are set to `up(1)'. down(2). The interface is not operational. dormant(5). This value is only applicable for Ethernet Transport Service Trail Termination Points (ETS TTP). The TTP is pending establishment of the terminating connection from the remote node. notPresent(6). The physical interface (and its device) is not present. partial(9). If the interface is representing a multicast ETS TTP, then the connections have been established to some, but not to all the configured destinations. If the interface is representing an interface group, then some but not all member interfaces have their operational status set to `up(1)." ::= { ethIfEntry 8 } ethIfFailure OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A string describing the configuration or error status of the interface. The string is the empty string if the configuration is correct, otherwise a message describing the error." ::= { ethIfEntry 9 } ethIfForwardingFunction OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The index (ethFwdIndex) in the ethFwdFuncTable of the forwarding function that this interface belongs to. The value -1 denotes that the interface does not belong to any forwarding function. If the referenced forwarding function is deleted, then the value of this object is automatically reset to -1. Note that the interface can only belong to a forwarding function on the same device as the interface. An interface group and its member interfaces always refer to the same forwarding function." DEFVAL { -1 } ::= { ethIfEntry 10 } ethIfAcceptableFrameTypes OBJECT-TYPE SYNTAX INTEGER { all(1), vlanTagged(2), untagged(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "all(1). All frames, regardless of whether they have a VLAN tag or not, shall be accepted. vlanTagged(2). Only frames that contain a non-zero VLAN id in the VLAN tag shall be accepted. untagged(3). Only frames without a VLAN tag or with VLAN id zero shall be accepted. The function of this variable depends on the setting of ethFwdVLANMode on the forwarding function to which the interface is connected. If the VLAN mode is set to `transparent(1)', then the setting of this variable is ignored. If the VLAN mode is set to `customer(2)', then only customer VLAN tags are examined. If the VLAN mode is set to `provider(3)', then only service VLAN tags are examined." DEFVAL { all } ::= { ethIfEntry 11 } ethIfTransmittedFrameType OBJECT-TYPE SYNTAX INTEGER { vlanTagged(2), untagged(3), legacy(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "vlanTagged(2). Forwarded frames are tagged according to setting on ethFwdVLANMode. untagged(3). VLAN tags on forwarded frames are removed according to setting of ethFwdVLANMode. legacy(4). VLAN id is transported together with frame, but the frame is in itself not tagged. The function depends on the setting of ethFwdVLANMode. If ethFwdVLANMode is set to `transparent(1)', then the setting of this variable is ignored. If it is set to `customer(2), then only customer VLAN tags are handled, and a service VLAN tag on the frame is unchanged. If the value is `provider(3)', then only service VLAN tags are handled, and a customer VLAN tag is unchanged." DEFVAL { vlanTagged } ::= { ethIfEntry 12 } ethIfDefaultVLAN OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "If an untagged frame is received on this interface, it will be tagged with a VLAN having a VLAN id as specified in this variable. The VLAN tag will be a customer or service tag as set on ethFwdVLANMode, or ignored if set to `transparent(1)'." DEFVAL { 1 } ::= { ethIfEntry 13 } ethIfDefaultEthernetPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the Ethernet priority assigned to a frame that has arrived via this port, and that does not have a VLAN tag. Priority will only be assigned to the frame if it should be sent out tagged on another port. This object is not affecting the traffic class assigned to the frame. The traffic class will be assigned to the frame based on the DSCP (if ethIfPriorityMode is set to `diffserv(2)') or to the value of ethIfDefaultTrafficClass." DEFVAL { 0 } ::= { ethIfEntry 14 } ethIfPriorityMode OBJECT-TYPE SYNTAX INTEGER { ethernet(1), diffserv(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Selects the method to use when assigning a flow group to a frame that arrives via this interface: ethernet(1). The user bits are used. diffserv(2). The differential service code point (DSCP) field of the IP header is translated using the ethFwdDiffservTable into a flow group." DEFVAL { ethernet } ::= { ethIfEntry 15 } ethIfDefaultTrafficClass OBJECT-TYPE SYNTAX TrafficClass MAX-ACCESS read-write STATUS current DESCRIPTION "Frames that do have any priority information are assigned this traffic class. See ethDevCapMaxTrafficClass for max value supported by the device." DEFVAL { 0 } ::= { ethIfEntry 16 } ethIfFlowGroupMap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Represents a flow group to traffic class map. The octet string consists of eight octets, one for each flow group. The position in the string represents the flow group, where the first (left-most) position represents flow group 0. The value of the octet represents the mapped traffic class for the flow group, where the value of zero represents traffic class 0 and so on. See ethDevCapMaxTrafficClass for max value supported by the device." DEFVAL { '00000000'H } ::= { ethIfEntry 17 } ethIfLearning OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies if MAC learning is enabled on the interface. on(1). MAC learning is enabled. The forwarding function learns what interface to use for a destination by looking at the source MAC address in received frames. off(2) MAC learning is disabled. Regardless of the setting, learning is disabled if ethFwdMACMode is set to nomac(3) or if it is set to auto(1) and less than three interfaces are connected to the forwarding function." DEFVAL { on } ::= { ethIfEntry 18 } ethIfInSpeed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current input bandwidth in bits per second. If the interface is a physical interface (represented in ethDot3Table), then this value is the same as ethDot3ActiveSpeed. If the interface represents an Ethernet Transport Service Trail Termination Point (ETS TTP), then this value is the sum of the bandwidth of all terminating channels connected to this interface. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ethIfInHighSpeed must be used to report the interface's speed." ::= { ethIfEntry 19 } ethIfInHighSpeed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current input bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the interface is somewhere in the range of `n-500,000' to `n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth." ::= { ethIfEntry 20 } ethIfOutSpeed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current output bandwidth in bits per second. If the interface is a physical interface (represented in ethDot3Table), then this value is the same as ethDot3ActiveSpeed. If the interface represents an Ethernet Transport Service Trail Termination Point (ETS TTP), then this value is the sum of the bandwidth of all originating channels connected to this interface. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ethIfOutHighSpeed must be used to report the interface's speed." ::= { ethIfEntry 21 } ethIfOutHighSpeed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current output bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the interface is somewhere in the range of `n-500,000' to `n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth." ::= { ethIfEntry 22 } ethIfVLANNextIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Next available value of ethIfVLANSetIndex in ethIfVLANSetTable for this interface." ::= { ethIfEntry 23 } ethIfLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time when the operational state or any configuration was last changed on this interface." ::= { ethIfEntry 24 } ethIfSrcPmReference OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A reference to an object that presents performance data for the source side of the interface. The object is not part of this MIB." ::= { ethIfEntry 25 } ethIfSnkPmReference OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A reference to an object that presents performance data for the sink side of the interface. The object is not part of this MIB." ::= { ethIfEntry 26 } ethIfSrcDegThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Threshold in number of dropped frames per second for generating a degraded second. A degraded second is generated when the number of dropped frames are equal or larger than the this threshold. A value of 0 disables degraded seconds detection." DEFVAL { 100 } ::= { ethIfEntry 27 } ethIfSnkDegThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Threshold in number of dropped frames per second for generating a degraded second. A degraded second is generated when the number of dropped frames are equal or larger than the this threshold. A value of 0 disables degraded seconds detection." DEFVAL { 100 } ::= { ethIfEntry 28 } ethIfSrcDegPeriod OBJECT-TYPE SYNTAX Unsigned32 (2..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of consecutive bad seconds that are needed for generating degraded signal alarm and/or AIS." DEFVAL { 7 } ::= { ethIfEntry 29 } ethIfSnkDegPeriod OBJECT-TYPE SYNTAX Unsigned32 (2..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of consecutive bad seconds that are needed for generating degraded signal alarm and/or AIS." DEFVAL { 7 } ::= { ethIfEntry 30 } ethIfSrcReducedBitRateThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in bits per second that is needed for generating a major alarm and/or AIS. If the threshold for the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ethIfSrcReducedBitRateHighThreshold must be used to set or report the threshold value. A value of 0 disables the reduced bit rate detection." DEFVAL { 0 } ::= { ethIfEntry 31 } ethIfSnkReducedBitRateThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in bits per second that is needed for generating a major alarm and/or AIS. If the threshold for the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ethIfSnkReducedBitRateHighThreshold must be used to set or report the threshold value. A value of 0 disables the reduced bit rate detection." DEFVAL { 0 } ::= { ethIfEntry 32 } ethIfSrcReducedBitRateHighThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a major alarm and/or AIS. If this object reports a value of `n' then the threshold value is somewhere in the range of `n-500,000' to `n+499,999'." DEFVAL { 0 } ::= { ethIfEntry 33 } ethIfSnkReducedBitRateHighThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a major alarm and/or AIS. If this object reports a value of `n' then the threshold value is somewhere in the range of `n-500,000' to `n+499,999'." DEFVAL { 0 } ::= { ethIfEntry 34 } ethIfSrcReducedBitRateAIS OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Defines if Reduced Bit Rate signal shall result in generation of AIS." DEFVAL { false } ::= { ethIfEntry 35 } ethIfSnkReducedBitRateAIS OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Defines if Reduced Bit Rate signal shall result in generation of AIS." DEFVAL { false } ::= { ethIfEntry 36 } ethIfSnkDegAIS OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Defines if degraded signal on the sink interface shall result in generation of AIS." DEFVAL { false } ::= { ethIfEntry 37 } ethIfSrcMinorReducedBitRateThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in bits per second that is needed for generating a minor alarm. If the threshold for the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ethIfSrcMinorReducedBitRateHighThreshold must be used to set or report the threshold value. A value of 0 disables the reduced bit rate detection." DEFVAL { 0 } ::= { ethIfEntry 38 } ethIfSnkMinorReducedBitRateThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in bits per second that is needed for generating a minor alarm. If the threshold for the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ethIfSnkMinorReducedBitRateHighThreshold must be used to set or report the threshold value. A value of 0 disables the reduced bit rate detection." DEFVAL { 0 } ::= { ethIfEntry 39 } ethIfSrcMinorReducedBitRateHighThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a minor alarm. If this object reports a value of `n' then the threshold value is somewhere in the range of `n-500,000' to `n+499,999'." DEFVAL { 0 } ::= { ethIfEntry 40 } ethIfSnkMinorReducedBitRateHighThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reduced Bit Rate threshold in 1,000,000 bits per second that is needed for generating a minor alarm. If this object reports a value of `n' then the threshold value is somewhere in the range of `n-500,000' to `n+499,999'." DEFVAL { 0 } ::= { ethIfEntry 41 } ethIfSrcFailure OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A string describing the configuration or error status of the source sub-interface. The string is the empty string if the configuration is correct, otherwise a message describing the error." ::= { ethIfEntry 42 } ethIfSnkFailure OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A string describing the configuration or error status of the sink sub-interface. The string is the empty string if the configuration is correct, otherwise a message describing the error." ::= { ethIfEntry 43 } ethIfInterfaceGroup OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The index (ethIfIndex) in the ethIfTable of the interface group that this interface belongs to. The value -1 denotes that the interface does not belong to an interface group. Note that the interface can only belong to an interface group on the same device as the interface. The interface can only belong to an interface group type of object, meaning that the object can only be set to an index of an object that exist in the ethIfgTable or where the value of ethIfType is `bETSGroup'. Setting this to the index of the interface group will add the interface to the interface group, making it a member of that interface group. If this is the first interface added to the interface group, then the interface group will inherit values on some of its object from this interface. If this is an additional interface added to the interface group, then this interface will inherit the same values from the interface group." ::= { ethIfEntry 44 } ethIfMaxMaxQueueFrames OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum allowed value for the maximum queue size for queues on the interface, ethIfQueueMaxFrames." ::= { ethIfEntry 45 } ethIfDefaultDropPrecedence OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Frames that do have any priority information are assigned this drop precedence (DP). The drop precedence must be in the range 0 to (ethDevCapDropPrecedenceLevels - 1)." DEFVAL { 0 } ::= { ethIfEntry 46 } ethIfDropPrecedenceMap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Represents a flow group to drop precedence (DP) map. The octet string consists of eight octets, one for each flow group. The position in the string represents the flow group, where the first (left-most) position represents flow group 0. The value of the octet represents the mapped drop precedence for the flow group, where the value of zero represents drop precedence 0 and so on. The drop precedence must be in the range 0 to (ethDevCapDropPrecedenceLevels - 1)." DEFVAL { '00000000'H } ::= { ethIfEntry 47 } -- End of Interface base table -- Queue Table ethIfQueueTable OBJECT-TYPE SYNTAX SEQUENCE OF EthIfQueueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Queues, one queue per interface and traffic class." ::= { ethInterfaceGroup 3 } ethIfQueueEntry OBJECT-TYPE SYNTAX EthIfQueueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing one queue." INDEX { ethDevIndex, ethIfIndex, ethIfQueueTrafficClass } ::= { ethIfQueueTable 1 } EthIfQueueEntry ::= SEQUENCE { ethIfQueueTrafficClass TrafficClass, ethIfQueueMaxOctets Integer32, ethIfQueueMaxFrames Integer32 } ethIfQueueTrafficClass OBJECT-TYPE SYNTAX TrafficClass MAX-ACCESS not-accessible STATUS current DESCRIPTION "Traffic class representing the queue. The index ranges from 0 to the max number of traffic classes - 1. See ethDevCapMaxTrafficClass for max value supported by the device." ::= { ethIfQueueEntry 1 } ethIfQueueMaxOctets OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of octets that can be queued for input on the interface and traffic class. If an arriving frame is too large to fit into the queue, the frame is dropped. A setting of -1 results in a queue setting so that the queuing delay is less than one second. Note that ethDevCapMaxMaxQueueOctets specifies the maximum value supported by the device." DEFVAL { -1 } ::= { ethIfQueueEntry 2 } ethIfQueueMaxFrames OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of frames that can be queued for input on the interface and traffic class. A setting of 0 means that queuing is disabled and frames destined for the queue are dropped. A setting of -1 means that the queue length is assigned automatically based on the number of available buffers. Note that ethIfMaxMaxQueueFrames specifies the maximum value supported by the interface." DEFVAL { -1 } ::= { ethIfQueueEntry 3 } -- End of Queue table -- VLAN sets ethIfVLANSetsTable OBJECT-TYPE SYNTAX SEQUENCE OF EthIfVLANSetsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table with VLAN sets. An interface belongs to the VLANs described by the union of all VLAN ids specified in all VLAN sets for the interface. Is possible to describe the same VLAN ids either by using one or by using multiple VLAN sets. Because the administrative data customer id and purpose can be set per VLAN set, it is possible to assign these differently for different VLAN ids when using multiple VLAN sets." ::= { ethInterfaceGroup 4 } ethIfVLANSetsEntry OBJECT-TYPE SYNTAX EthIfVLANSetsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a VLAN set. A VLAN set represents a list of VLAN ids that an interface shall belong to." INDEX { ethDevIndex, ethIfIndex, ethIfVLANSetIndex } ::= { ethIfVLANSetsTable 1 } EthIfVLANSetsEntry ::= SEQUENCE { ethIfVLANSetIndex Unsigned32, ethIfVLANRowStatus RowStatus, ethIfVLANSet VLANSet, ethIfVLANCustomerId Unsigned32, ethIfVLANPurpose SnmpAdminString } ethIfVLANSetIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index representing the VLAN set." ::= { ethIfVLANSetsEntry 1 } ethIfVLANRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "See SNMPv2-TC. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new VLAN set. destroy(6). The VLAN set is deleted." ::= { ethIfVLANSetsEntry 2 } ethIfVLANSet OBJECT-TYPE SYNTAX VLANSet MAX-ACCESS read-create STATUS current DESCRIPTION "A set of VLAN ids that the interface belongs to." DEFVAL { ''H } ::= { ethIfVLANSetsEntry 3 } ethIfVLANCustomerId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "An identification number representing the customer or user using the VLAN set. The value could be used for e.g. Charge Data Records. The value zero (0) indicates that no specific customer shall be associated with the VLAN set." DEFVAL { 0 } ::= { ethIfVLANSetsEntry 4 } ethIfVLANPurpose OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A string representing the purpose of the VLAN set. The string is for administrative purpose." DEFVAL { ''H } ::= { ethIfVLANSetsEntry 5 } -- End of VLAN sets -- Dot3 table for physical interfaces ethDot3Table OBJECT-TYPE SYNTAX SEQUENCE OF EthDot3Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table that contains representations of physical interfaces." ::= { ethInterfaceGroup 5 } ethDot3Entry OBJECT-TYPE SYNTAX EthDot3Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing one physical interface. For each conceptual row in this table, a conceptual row with the same index exists in the interface base table ethIfTable. Entries in this table shall automatically be created when a device is added to the ethDevTable, and are removed when the device is destroyed." INDEX { ethDevIndex, ethIfIndex } ::= { ethDot3Table 1 } EthDot3Entry ::= SEQUENCE { ethDot3AutoNegotiate TruthValue, ethDot3AdvertisedSpeed AdvertisedSpeed, ethDot3AdvertisedDuplex AdvertisedDuplex, ethDot3AdvertisedFlowControl AdvertisedFlowControl, ethDot3ActiveSpeed Unsigned32, ethDot3ActiveDuplex INTEGER, ethDot3ActiveFlowControl INTEGER, ethDot3ForceVLANTagged VLANSet, ethDot3ForceVLANUntagged VLANSet, ethDot3SupportedSpeeds AdvertisedSpeed, ethDot3ResetToDefaults Integer32, ethDot3AutoNegotiateStatus TruthValue, ethDot3AutoNegotiateAllowed TruthValue, ethDot3AutoNegotiateMandatory TruthValue, ethDot3SupportedIfType BITS, ethDot3SelectedIfType EthInterfaceType } ethDot3AutoNegotiate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the desired value of auto-negotiation: true(1). Auto-negotiation shall be enabled. If the interface does not allow auto-negotiation, then this object is ignored. false(2). Auto-negotiation shall be disabled. See ethDot3AutoNegotiateStatus for actual resulting status." DEFVAL { true } ::= { ethDot3Entry 1 } ethDot3AdvertisedSpeed OBJECT-TYPE SYNTAX AdvertisedSpeed MAX-ACCESS read-write STATUS current DESCRIPTION "The link speeds that the interface shall advertise that it supports. If auto-negotiation is disabled, then use the highest set link speed." DEFVAL { { auto } } ::= { ethDot3Entry 2 } ethDot3AdvertisedDuplex OBJECT-TYPE SYNTAX AdvertisedDuplex MAX-ACCESS read-write STATUS current DESCRIPTION "The duplex settings that the interface shall advertise that it supports. See ethDevCapAdvertisedDuplex for allowed duplex settings on the device." DEFVAL { { auto } } ::= { ethDot3Entry 3 } ethDot3AdvertisedFlowControl OBJECT-TYPE SYNTAX AdvertisedFlowControl MAX-ACCESS read-write STATUS current DESCRIPTION "The flow control settings that the interface shall advertise that it supports. If auto-negotiation is disabled (ethDot3SAutoNegotiate), then this object describes the flow control that shall be used. `auto(0)' is then equivalent to flow control in both direction." REFERENCE "IEEE 802.3-2005 Section Two" DEFVAL { { auto } } ::= { ethDot3Entry 4 } ethDot3ActiveSpeed OBJECT-TYPE SYNTAX Unsigned32 (0|10|100|1000|10000) MAX-ACCESS read-only STATUS current DESCRIPTION "The active links speed in Mbps." ::= { ethDot3Entry 5 } ethDot3ActiveDuplex OBJECT-TYPE SYNTAX INTEGER { fullDuplex(1), halfDuplex(2), notApplicable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The active link duplex. If the interface is down, then `notApplicable(3)' is presented." ::= { ethDot3Entry 6 } ethDot3ActiveFlowControl OBJECT-TYPE SYNTAX INTEGER { all(1), receive(2), transmit(3), none(4), notApplicable(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The active link flow control. If the interface is down, then `notApplicable(5)' is presented." ::= { ethDot3Entry 7 } ethDot3ForceVLANTagged OBJECT-TYPE SYNTAX VLANSet MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies a set of VLAN ids for which frames shall be forwarded with a tag although ethIfTransmittedFrameType is set to `untagged(3)'. The setting of this variable has no meaning if ethIfTransmittedFrameType is set to `vlanTagged(2)', or if ethFwdVLANMode is set to `transparent(1)' The value of ethFwdVLANMode specifies if the customer or service VLAN ids are interpreted." DEFVAL { ''H } ::= { ethDot3Entry 8 } ethDot3ForceVLANUntagged OBJECT-TYPE SYNTAX VLANSet MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies a set of VLAN ids for which frames shall be forwarded without a tag although ethIfTransmittedFrameType is set to `vlanTagged(2)'. The setting of this variable has no meaning if ethIfTransmittedFrameType is set to `untagged(3)', or if ethFwdVLANMode is set to `transparent(1)'. The value of ethFwdVLANMode specifies if the customer or service VLAN ids are interpreted." DEFVAL { ''H } ::= { ethDot3Entry 9 } ethDot3SupportedSpeeds OBJECT-TYPE SYNTAX AdvertisedSpeed MAX-ACCESS read-only STATUS current DESCRIPTION "All supported speeds for ethDot3AdvertisedSpeed. Note that this value depends on the SFP." ::= { ethDot3Entry 10 } ethDot3ResetToDefaults OBJECT-TYPE SYNTAX Integer32 (0) MAX-ACCESS read-write STATUS current DESCRIPTION "Writing a zero (0) resets all the the settings on the interface to its default values." ::= { ethDot3Entry 11 } ethDot3AutoNegotiateStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if auto-negotiation is enabled or not." ::= { ethDot3Entry 12 } ethDot3AutoNegotiateAllowed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if auto-negotiation is permitted with the current combination of interface type and speed." ::= { ethDot3Entry 13 } ethDot3AutoNegotiateMandatory OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if auto-negotiation is required with the current combination of interface type and speed." ::= { ethDot3Entry 14 } ethDot3SupportedIfType OBJECT-TYPE SYNTAX BITS { -- auto(0), -- unknown(1), -- bETS(2), b100baseTX(3), b1000baseSX(4), b1000baseLX(5), b1000baseT(6), -- bETSGroup(7), b10GbaseSR(8), b10GbaseLR(9), b10GbaseLRM(10), b10GbaseER(11), b10GbaseZR(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "All supported interface types on the interface. This denotes what can be set on ethDot3SelectedIfType. Note that this value depends on the SFP." ::= { ethDot3Entry 15 } ethDot3SelectedIfType OBJECT-TYPE SYNTAX EthInterfaceType MAX-ACCESS read-write STATUS current DESCRIPTION "Selected interface speed. A selected value of `auto(0)' means that the interface type with the highest available line speed will be used. See ethIfType for the currently used type. The interface type must correspond to a supported type as presented by ethDot3SupportedIfType. " ::= { ethDot3Entry 16 } -- End of Dot3 table for physical interfaces (MAU) -- Ethernet Transport Service (ETS) interfaces table ethEtsTable OBJECT-TYPE SYNTAX SEQUENCE OF EthEtsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table that contains definitions of Trail Termination Points (TTPs) for Ethernet Transport Service. For every row in the table, a corresponding row exists in the table ethIfTable." ::= { ethInterfaceGroup 6 } ethEtsEntry OBJECT-TYPE SYNTAX EthEtsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing one ETS TTP." INDEX { ethDevIndex, ethIfIndex } ::= { ethEtsTable 1 } EthEtsEntry ::= SEQUENCE { ethEtsRowStatus RowStatus, ethEtsMode INTEGER, ethEtsLocalDsti Dsti, ethEtsODescription Unsigned32, ethEtsOConnection Unsigned32, ethEtsSnkExpectChannel TruthValue } ethEtsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "See SNMPv2-TC. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new Ethernet Transport Service Trail Termination Point, ETS TTP. To activate the connection, set the administrative status to up(1) after all columnar objects have been updated. destroy(6). The connection is terminated and deleted." ::= { ethEtsEntry 1 } ethEtsMode OBJECT-TYPE SYNTAX INTEGER { unicast(1), multicast(2), unspecified(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the ETS TTP shall establish unicast or multicast connection." DEFVAL { unspecified } ::= { ethEtsEntry 2 } ethEtsLocalDsti OBJECT-TYPE SYNTAX Dsti MAX-ACCESS read-create STATUS current DESCRIPTION "The DSTI (DTM Service Type Instance) for the local application implementing the service. A valid value is automatically assigned when the conceptual row is created. Any unique value may be assigned to this object." ::= { ethEtsEntry 3 } ethEtsODescription OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "A reference to the corresponding description of the connection in the chmgrODescriptionTable in the Channel Manager MIB (NETI-CHMGR-MIB). The value is the index into the table, i.e. the value of chmgrODescrIndex. When a row is created in or deleted from this table, the corresponding row is created in or deleted from the table chmgrODescriptionTable." ::= { ethEtsEntry 4 } ethEtsOConnection OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A reference to the corresponding originating connection in the table chmgrOConnectionTable in the Channel Manager MIB (NETI-CHMGR-MIB). When an originating connection is established from this trail termination point, an entry is created in the table. The value is the index into that table, i.e. the value of chmgrOConnIndex. If no connection is established or associated with this connection, this is indicated by a value of zero (0)." ::= { ethEtsEntry 5 } ethEtsSnkExpectChannel OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls whether a channel is expected to be terminated on this ETS TTP or not. This value can only be set if the mode (ethEtsMode) is multicast. true(1). A channel is expected to terminate. If a channel is not terminating, then this is regarded as an anomaly. false(2). A channel is not expected to terminate. Absence of a terminating channel is considered to be correct." DEFVAL { false } ::= { ethEtsEntry 6 } -- End of the ETS table -- The ETS Terminating Connection table ethEtsTConnectionTable OBJECT-TYPE SYNTAX SEQUENCE OF EthEtsTConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table that holds references to terminating connections for a ETS trail termination point. A trail termination point can terminate only one connection if a unicast connection is configured, and multiple connections if a multicast connection is configured." ::= { ethInterfaceGroup 7 } ethEtsTConnectionEntry OBJECT-TYPE SYNTAX EthEtsTConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing the reference to one terminating connection." INDEX { ethDevIndex, ethIfIndex, ethEtsTConnectionIndex } ::= { ethEtsTConnectionTable 1 } EthEtsTConnectionEntry ::= SEQUENCE { ethEtsTConnectionIndex Unsigned32, ethEtsTConnectionRowStatus RowStatus, ethEtsTConnection Unsigned32 } ethEtsTConnectionIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index representing one terminating connection for the trail terminating point. If the trail terminating point is unicast, the value of the index is always one (1) as a unicast trail terminating point can only terminate one connection." ::= { ethEtsTConnectionEntry 1 } ethEtsTConnectionRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Row status according to SNMPv2-TC. It is only possible to delete rows. Rows are created by the application. If a row is deleted that represents an active connection, a new row will be created representing that connection. The supported values are: active(1). The value always reads active. destroy(6). The terminating side of the connection is deleted." ::= { ethEtsTConnectionEntry 2 } ethEtsTConnection OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A reference to the corresponding terminating connection in the table chmgrTConnectionTable in the Channel Manager MIB (NETI-CHMGR-MIB). When a connection is terminated on this trail termination point, an entry is created in the table. The value is the index into that table, i.e. the value of chmgrTConnIndex. If no terminating connections exist, this is indicated by a value of zero (0)." ::= { ethEtsTConnectionEntry 3 } -- End of the ETS Terminating Connection table -- The DSTI to Index Lookup Table ethEtsIndexLookupTable OBJECT-TYPE SYNTAX SEQUENCE OF EthEtsIndexLookupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table to lookup the index in the ethEtsTable, corresponding to a specific DSTI." ::= { ethInterfaceGroup 8 } ethEtsIndexLookupEntry OBJECT-TYPE SYNTAX EthEtsIndexLookupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "One conceptual row representing one lookup entry." INDEX { ethEtsLocalDsti } ::= { ethEtsIndexLookupTable 1 } EthEtsIndexLookupEntry ::= SEQUENCE { ethEtsIndexLookupDevIndex Unsigned32, ethEtsIndexLookupIfIndex Unsigned32 } ethEtsIndexLookupDevIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value refers to the ethDevIndex in the ethEtsTable for the ETS interface represented by the DSTI." ::= { ethEtsIndexLookupEntry 1 } ethEtsIndexLookupIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value refers to the ethIfIndex in the ethEtsTable for the ETS interface represented by the DSTI." ::= { ethEtsIndexLookupEntry 2 } -- End of the DSTI to Index Lookup Table -- Rapid Spanning Tree Protocol interface table ethIfRstpTable OBJECT-TYPE SYNTAX SEQUENCE OF EthIfRstpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains Rapid Spanning Tree Protocol (RSTP) specific configurations and data for ports. If a port does not support RSTP, then the table will not hold an entry for that port." ::= { ethInterfaceGroup 9 } ethIfRstpEntry OBJECT-TYPE SYNTAX EthIfRstpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry represents Rapid Spanning Tree Protocol (RSTP) data for one port (interface)." INDEX { ethDevIndex, ethIfIndex } ::= { ethIfRstpTable 1 } EthIfRstpEntry ::= SEQUENCE { ethIfRstpPortIdentifier PortIdentifier, ethIfRstpPriority Integer32, ethIfRstpState INTEGER, ethIfRstpTopologyChangeAcknowledge TruthValue, ethIfRstpPathCost Integer32, ethIfRstpDesignatedRoot BridgeIdentifier, ethIfRstpDesignatedCost Integer32, ethIfRstpDesignatedBridge BridgeIdentifier, ethIfRstpDesignatedPort PortIdentifier, ethIfRstpAdminEdgePort INTEGER, ethIfRstpOperEdgePort TruthValue, ethIfRstpAdminPointToPointMAC INTEGER, ethIfRstpOperPointToPointMAC TruthValue, ethIfRstpCurrentPathCost Integer32 } ethIfRstpPortIdentifier OBJECT-TYPE SYNTAX PortIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The unique port identifier." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." ::= { ethIfRstpEntry 1 } ethIfRstpPriority OBJECT-TYPE SYNTAX Integer32 (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The port priority. The value must be set in increments of 16." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.3.2 and 17.14." DEFVAL { 128 } ::= { ethIfRstpEntry 2 } ethIfRstpState OBJECT-TYPE SYNTAX INTEGER { discarding(1), learning(2), forwarding(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Describes if the port forwards MAC frames and whether or not it learns from their source addresses. discarding(1). The port is not enabled or has been excluded from forwarding and learning. learning(2). The port has learning enabled, but forwarding disabled. forwarding(3). The port both learns and forwards frames." REFERENCE "IEEE 802.1D-2004: clause 7.4." ::= { ethIfRstpEntry 3 } ethIfRstpTopologyChangeAcknowledge OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "true(1). A topology change is in progress and the port is about to acknowledge this. false(2). A topology change is not in progress." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." ::= { ethIfRstpEntry 4 } ethIfRstpPathCost OBJECT-TYPE SYNTAX Integer32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port. A value of zero (0) means that the path cost is automatically calculated based on the port speed, as per formula: 20,000,000 / min(ethIfInSpeed, ethIfOutSpeed) " REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." DEFVAL { 0 } ::= { ethIfRstpEntry 5 } ethIfRstpDesignatedRoot OBJECT-TYPE SYNTAX BridgeIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The unique bridge identifier of the root bridge." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." ::= { ethIfRstpEntry 6 } ethIfRstpDesignatedCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The path cost to the root bridge from the designated bridge." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." ::= { ethIfRstpEntry 7 } ethIfRstpDesignatedBridge OBJECT-TYPE SYNTAX BridgeIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the best bridge connected to this port's segment." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." ::= { ethIfRstpEntry 8 } ethIfRstpDesignatedPort OBJECT-TYPE SYNTAX PortIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier of the best port on the Designated Bridge." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." ::= { ethIfRstpEntry 9 } ethIfRstpAdminEdgePort OBJECT-TYPE SYNTAX INTEGER { auto(0), true(1), false(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting of the edge port state of this port. auto(0). The setting of the port as edge port or not is done automatically. See ethIfRstpOperEdgePort for the current value when this object is set to `auto(0)'. true(1). The port is an edge port. false(2). The port is not an edge port. " REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3 and 17.25." DEFVAL { auto } ::= { ethIfRstpEntry 10 } ethIfRstpOperEdgePort OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The actual state of the port. See ethIfRstpAdminEdgePort for setting of the port state. true(1). The port is an edge port. false(2). The port is not an edge port." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3 and 17.25." ::= { ethIfRstpEntry 11 } ethIfRstpAdminPointToPointMAC OBJECT-TYPE SYNTAX INTEGER { auto(0), true(1), false(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting of the point-to-point state of this port. auto(0). The state becomes `true(1)' if the port is a full-duplex physical port, or an ETS TTP with a maximum of one terminating channel. Otherwise the state becomes `false(2)'. true(1). The port is a point-to-point port. false(2). The port is not a point-to-point port." REFERENCE "IEEE 802.1D-2004: clause 6.4.3." DEFVAL { auto } ::= { ethIfRstpEntry 12 } ethIfRstpOperPointToPointMAC OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " The point-to-point state of this port." REFERENCE "IEEE 802.1D-2004: clause 14.8.2.1.3." ::= { ethIfRstpEntry 13 } ethIfRstpCurrentPathCost OBJECT-TYPE SYNTAX Integer32 (1..200000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Unless ethIfRstpPathCost is `auto(1), then this always reads the same value as that object." ::= { ethIfRstpEntry 14 } -- End of Rapid Spanning Tree Protocol Table -- Start of Interface Group Table ethIfgTable OBJECT-TYPE SYNTAX SEQUENCE OF EthIfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table that contains definitions of interface groups. For every row in the table, a corresponding row exists in the table ethIfTable." ::= { ethInterfaceGroup 10 } ethIfgEntry OBJECT-TYPE SYNTAX EthIfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing one interface group. An interface group is a virtual interface that groups two ETS interfaces for 1+1 protected transport of Ethernet." INDEX { ethDevIndex, ethIfIndex } ::= { ethIfgTable 1 } EthIfgEntry ::= SEQUENCE { ethIfgRowStatus RowStatus, ethIfgMembers InterfaceIndexList, ethIfgDifferentialDelay Unsigned32, ethIfgDifferentialDelayValid TruthValue, ethIfgAheadInterface Unsigned32, ethIfgHitlessProtection TruthValue, ethIfgProtectionStatus IfgProtectionStatus, ethIfgExpectedProtectionStatus IfgProtectionStatus, ethIfgForceHit Unsigned32, ethIfgActiveInterface Unsigned32, ethIfgExpectChannel TruthValue } ethIfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "See SNMPv2-TC. The following values are supported: active(1). The object always reads active. createAndGo(4). A new conceptual row is created representing a new interface group. destroy(6). The connection is terminated and deleted. An interface group can be destroyed only if it has no member interfaces." ::= { ethIfgEntry 1 } ethIfgMembers OBJECT-TYPE SYNTAX InterfaceIndexList MAX-ACCESS read-only STATUS current DESCRIPTION "A list of the interfaces that are members of the interface group. An interface is added or removed from an interface group from the interface using ethIfInterfaceGroup." ::= { ethIfgEntry 2 } ethIfgDifferentialDelay OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The measured difference delay in microseconds between the two channels in the interface group." ::= { ethIfgEntry 3 } ethIfgDifferentialDelayValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies if the value of ethIfgDifferentialDelay is valid or not." ::= { ethIfgEntry 4 } ethIfgAheadInterface OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of ethIfIndex of the interface that is ahead of the other. A value of zero (0) implies invalid, i.e. no channel is established. If only one interface is a member of the interface group, then that interface is considered ahead." ::= { ethIfgEntry 5 } ethIfgHitlessProtection OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies if hitless protection shall be attempted or not. true(1). Will attempt to reach a hitless protection state. false(2). Will only attempt to reach a standby protection state." DEFVAL { false } ::= { ethIfgEntry 6 } ethIfgProtectionStatus OBJECT-TYPE SYNTAX IfgProtectionStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The current protection state." ::= { ethIfgEntry 7 } ethIfgExpectedProtectionStatus OBJECT-TYPE SYNTAX IfgProtectionStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The expected protection state. When the current protection state (see ethIfgProtectionStatus) is lower than the expected protection state, an alarm is raised. The alarm is cleared when the expected protection state is equal or higher then the current protection state." DEFVAL { unavailable } ::= { ethIfgEntry 8 } ethIfgForceHit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "A write of zero (0) resets the buffers, and will therefore minimize the the latency penalty incurred by the 1+1 buffering." DEFVAL { 0 } ::= { ethIfgEntry 9 } ethIfgActiveInterface OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The value of ethIfIndex of the interface from where frames are currently being forwarded. If the ethIfgProtectionStatus is `unavailable(1)' then the value is zero (0)." ::= { ethIfgEntry 10 } ethIfgExpectChannel OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Controls whether a channel is expected to be terminated on this ETS TTPs for the member interfaces or not. This value can only be set if the mode (ethEtsMode) is multicast. true(1). A channel is expected to terminate. If a channel is not terminating, then this is regarded as an anomaly. false(2). A channel is not expected to terminate. Absence of a terminating channel is considered to be correct. This value of this object is inherited from the ethEtsSnkExpectChannel of the first interface added as a member. Writing to this object updates the value of ethEtsSnkExpectChannel of all the member interfaces." ::= { ethIfgEntry 11 } -- End of Interface Group Table -- Queue Drop Thresholds table ethIfQDropThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF EthIfQDropThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A queue (Traffic Class) can have multiple drop thresholds, one for each drop precedence. The table contains configuration of how to drop frames per combination of traffic class (TC) and drop precedence (DP) for the interfaces." ::= { ethInterfaceGroup 11 } ethIfQDropThresholdEntry OBJECT-TYPE SYNTAX EthIfQDropThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table." INDEX { ethDevIndex, ethIfIndex, ethIfQueueTrafficClass, ethIfQDropThresDropPrecedence } ::= { ethIfQDropThresholdTable 1 } EthIfQDropThresholdEntry ::= SEQUENCE { ethIfQDropThresDropPrecedence Unsigned32, ethIfQDropThresMaxFrames Integer32, ethIfQDropThresCurrentMaxFrames Integer32, ethIfQDropThresDropProbabilityFunction INTEGER } ethIfQDropThresDropPrecedence OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of drop precedence (DP). The value range is given by the device and is from zero to and including (ethDeviceDropPrecedenceLevels - 1)." ::= { ethIfQDropThresholdEntry 1 } ethIfQDropThresMaxFrames OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of frames that can be queued to this interface for this combination of traffic class and drop precedence. Arriving frames are discarded when the queue has reached its maximum length. A value of 0 denotes that all frames shall be discarded. A value of -1 denotes that the device automatically assigns the threshold value. The value must either be set to automatic threshold assignment (-1), or manually assigned (i.e. greater than 0) for all drop precedences on a queue." ::= { ethIfQDropThresholdEntry 2 } ethIfQDropThresCurrentMaxFrames OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of frames that currently can be queued to this interface for this combination of traffic class and drop precedence. This value contains the currently assigned threshold, both for automatic and manual threshold assignment set with ethIfQDropThresMaxFrames." ::= { ethIfQDropThresholdEntry 3 } ethIfQDropThresDropProbabilityFunction OBJECT-TYPE SYNTAX INTEGER { taildrop(0), wred(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The drop probability function that shall be used for the combination of traffic class and drop precedence on the interface. The values supported by the device are presented in ethDevDropProbabilityFunctions." DEFVAL { taildrop } ::= { ethIfQDropThresholdEntry 4 } -- End of Queue Drop Thresholds table -- -- Statistics -- -- Interface groups DCAP-1 statistics table -- Note that DCAP-1 statistics for interfaces can be found in NETI-CHMGR-MIB. ethStatDcap1Table OBJECT-TYPE SYNTAX SEQUENCE OF EthStatDcap1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table holds statistical DCAP-1 data for interface groups that are implemented using ETS connections." ::= { ethStatisticsGroup 1 } ethStatDcap1Entry OBJECT-TYPE SYNTAX EthStatDcap1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row holding DCAP-1 statistical data for a single interface group." INDEX { ethDevIndex, ethIfIndex } ::= { ethStatDcap1Table 1 } EthStatDcap1Entry ::= SEQUENCE { ethStatDcap1Reset Integer32, ethStatDcap1TxOctets Counter64, ethStatDcap1TxPackets Counter64, ethStatDcap1TxDiscardOctets Counter64, ethStatDcap1TxDiscardPackets Counter64, ethStatDcap1TxBitrate Counter64, ethStatDcap1TxLoad Unsigned32, ethStatDcap1RxOctets Counter64, ethStatDcap1RxPackets Counter64, ethStatDcap1RxDiscardOctets Counter64, ethStatDcap1RxDiscardPackets Counter64, ethStatDcap1RxErrorCRC Counter64, ethStatDcap1RxBitrate Counter64, ethStatDcap1RxLoad Unsigned32 } ethStatDcap1Reset OBJECT-TYPE SYNTAX Integer32 (0) MAX-ACCESS read-write STATUS current DESCRIPTION "Writing a zero (0) to this object resets all counters for the interface." ::= { ethStatDcap1Entry 1 } ethStatDcap1TxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of transmitted octets (bytes)." ::= { ethStatDcap1Entry 2 } ethStatDcap1TxPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of transmitted packets." ::= { ethStatDcap1Entry 3 } ethStatDcap1TxDiscardOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of transmitted and discarded octets (bytes)." ::= { ethStatDcap1Entry 4 } ethStatDcap1TxDiscardPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of transmitted and discarded packets." ::= { ethStatDcap1Entry 5 } ethStatDcap1TxBitrate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit utilization in bits per second on the connection as a mean value during the last 30 seconds." ::= { ethStatDcap1Entry 6 } ethStatDcap1TxLoad OBJECT-TYPE SYNTAX Unsigned32 (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit utilization (load) in percent on the connection as mean value measured during the last 30 seconds." ::= { ethStatDcap1Entry 7 } ethStatDcap1RxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received octets (bytes)." ::= { ethStatDcap1Entry 8 } ethStatDcap1RxPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received packets." ::= { ethStatDcap1Entry 9 } ethStatDcap1RxDiscardOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received and discarded octets (bytes)." ::= { ethStatDcap1Entry 10 } ethStatDcap1RxDiscardPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received packets that are discarded and not counted in ethStatDcap1RxErrorCRC." ::= { ethStatDcap1Entry 11 } ethStatDcap1RxErrorCRC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received packets with CRC32 error. For an interface group where the protectionStatus is `hitlessProtected(5)', this value is not increased." ::= { ethStatDcap1Entry 12 } ethStatDcap1RxBitrate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The receive utilization in bits per second on the connection as a mean value during the last 30 seconds." ::= { ethStatDcap1Entry 13 } ethStatDcap1RxLoad OBJECT-TYPE SYNTAX Unsigned32 (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "The receive utilization (load) in percent on the connection as mean value measured during the last 30 seconds." ::= { ethStatDcap1Entry 14 } -- End of interface group DCAP-1 statistics table -- Interface common statistics table ethIfStatTable OBJECT-TYPE SYNTAX SEQUENCE OF EthIfStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table holds statistical data for Ethernet interfaces." ::= { ethStatisticsGroup 2 } ethIfStatEntry OBJECT-TYPE SYNTAX EthIfStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row holding statistica data for a single interface." INDEX { ethDevIndex, ethIfIndex } ::= { ethIfStatTable 1 } EthIfStatEntry ::= SEQUENCE { ethIfStatReset Integer32, ethIfStatTxBitrate Counter64, ethIfStatTxLoad Unsigned32, ethIfStatRxBitrate Counter64, ethIfStatRxLoad Unsigned32 } ethIfStatReset OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Writing a zero (0) to this object resets all counters for the interface." ::= { ethIfStatEntry 1 } ethIfStatTxBitrate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit utilization in bits per second on the interface as a mean value during the last 30 seconds." ::= { ethIfStatEntry 2 } ethIfStatTxLoad OBJECT-TYPE SYNTAX Unsigned32 (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit utilization (load) in percent of the wire speed on the interface as mean value measured during the last 30 seconds." ::= { ethIfStatEntry 3 } ethIfStatRxBitrate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The receive utilization in bits per second on the interface as a mean value during the last 30 seconds." ::= { ethIfStatEntry 4 } ethIfStatRxLoad OBJECT-TYPE SYNTAX Unsigned32 (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "The receive utilization (load) in percent of the wire speed on the interface as mean value measured during the last 30 seconds." ::= { ethIfStatEntry 5 } -- End interface common statistics table END