-- ***************************************************************** -- FS-FIBER-MIB.mib: FS FIBER MIB file -- -- January 2012, wangyouliang -- -- Copyright (c) 2012 by FS.COM Inc.. -- All rights reserved. -- -- ***************************************************************** -- FS-FIBER-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI TruthValue, DisplayString FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF IfIndex FROM FS-TC fsMgmt FROM FS-SMI; fsFiberMIB MODULE-IDENTITY LAST-UPDATED "201111280000Z" ORGANIZATION "FS.COM Inc.." CONTACT-INFO " Tel: 400-865-2852 E-mail: https://www.fs.com/live_chat_service_mail.html" DESCRIPTION "This module defines fs fiber module information mibs." REVISION "201111280000Z" DESCRIPTION "Initial version of this MIB module." ::= { fsMgmt 105} fsFiberMIBObjects OBJECT IDENTIFIER ::= { fsFiberMIB 1 } -- ---------------------------------------------------------- -- -- A table for getting Fiber port information. -- ---------------------------------------------------------- -- fsFiberTable OBJECT-TYPE SYNTAX SEQUENCE OF FSFiberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for getting Fiber Module information" ::= { fsFiberMIBObjects 1 } fsFiberEntry OBJECT-TYPE SYNTAX FSFiberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of a Fiber Module information." INDEX { fsFiberPortIndex } ::= { fsFiberTable 1 } FSFiberEntry ::= SEQUENCE { fsFiberPortIndex IfIndex, fsFiberPortDescr DisplayString, fsFiberTransceiverType INTEGER, fsFiberConnectorType INTEGER, fsFiberWavelength INTEGER, fsFiberTransferDistanceSMF INTEGER, fsFiberTransferDistance62point5umOM1 INTEGER, fsFiberTransferDistance62point5um INTEGER, fsFiberTransferDistance50umOM2 INTEGER, fsFiberTransferDistance50um INTEGER, fsFiberTransferDistance50umOM3 INTEGER, fsFiberTransferDistanceEBW50um INTEGER, fsFiberTransferDistanceCopper INTEGER, fsFiberTransferDistanceCableAssembly INTEGER, fsFiberDDMSupportStatus TruthValue, fsFiberSerialNumber DisplayString, fsFiberTemp INTEGER, fsFiberTempStatus INTEGER, fsFiberVoltage INTEGER, fsFiberVoltageStatus INTEGER, fsFiberBias INTEGER, fsFiberBiasStatus INTEGER, fsFiberChannel1Bias INTEGER, fsFiberChannel1BiasStatus INTEGER, fsFiberChannel2Bias INTEGER, fsFiberChannel2BiasStatus INTEGER, fsFiberChannel3Bias INTEGER, fsFiberChannel3BiasStatus INTEGER, fsFiberChannel4Bias INTEGER, fsFiberChannel4BiasStatus INTEGER, fsFiberRXpowerIntegerpart INTEGER, fsFiberRXpowerDecimalpart INTEGER, fsFiberRXpowertype INTEGER, fsFiberRXpowerStatus INTEGER, fsFiberChannel1RXpowerIntegerpart INTEGER, fsFiberChannel1RXpowerDecimalpart INTEGER, fsFiberChannel1RXpowertype INTEGER, fsFiberChannel1RXpowerStatus INTEGER, fsFiberChannel2RXpowerIntegerpart INTEGER, fsFiberChannel2RXpowerDecimalpart INTEGER, fsFiberChannel2RXpowertype INTEGER, fsFiberChannel2RXpowerStatus INTEGER, fsFiberChannel3RXpowerIntegerpart INTEGER, fsFiberChannel3RXpowerDecimalpart INTEGER, fsFiberChannel3RXpowertype INTEGER, fsFiberChannel3RXpowerStatus INTEGER, fsFiberChannel4RXpowerIntegerpart INTEGER, fsFiberChannel4RXpowerDecimalpart INTEGER, fsFiberChannel4RXpowertype INTEGER, fsFiberChannel4RXpowerStatus INTEGER, fsFiberTXpowerIntegerpart INTEGER, fsFiberTXpowerDecimalpart INTEGER, fsFiberTXpowerStatus INTEGER, fsFiberChannel1TXpowerIntegerpart INTEGER, fsFiberChannel1TXpowerDecimalpart INTEGER, fsFiberChannel1TXpowerStatus INTEGER, fsFiberChannel2TXpowerIntegerpart INTEGER, fsFiberChannel2TXpowerDecimalpart INTEGER, fsFiberChannel2TXpowerStatus INTEGER, fsFiberChannel3TXpowerIntegerpart INTEGER, fsFiberChannel3TXpowerDecimalpart INTEGER, fsFiberChannel3TXpowerStatus INTEGER, fsFiberChannel4TXpowerIntegerpart INTEGER, fsFiberChannel4TXpowerDecimalpart INTEGER, fsFiberChannel4TXpowerStatus INTEGER, fsFiberRXpowerSign INTEGER, fsFiberChannel1RXpowerSign INTEGER, fsFiberChannel2RXpowerSign INTEGER, fsFiberChannel3RXpowerSign INTEGER, fsFiberChannel4RXpowerSign INTEGER, fsFiberTXpowerSign INTEGER, fsFiberChannel1TXpowerSign INTEGER, fsFiberChannel2TXpowerSign INTEGER, fsFiberChannel3TXpowerSign INTEGER, fsFiberChannel4TXpowerSign INTEGER, fsFiberRXpowerInteger INTEGER, fsFiberChannel1RXpowerInteger INTEGER, fsFiberChannel2RXpowerInteger INTEGER, fsFiberChannel3RXpowerInteger INTEGER, fsFiberChannel4RXpowerInteger INTEGER, fsFiberTXpowerInteger INTEGER, fsFiberChannel1TXpowerInteger INTEGER, fsFiberChannel2TXpowerInteger INTEGER, fsFiberChannel3TXpowerInteger INTEGER, fsFiberChannel4TXpowerInteger INTEGER } fsFiberPortIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port index of the port." ::= { fsFiberEntry 1 } fsFiberPortDescr OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Discription of the port." ::= { fsFiberEntry 2 } fsFiberTransceiverType OBJECT-TYPE SYNTAX INTEGER { unknown(1), fiber100BASEGTSFP(2), fiber100BASESXSFP(3), fiber100BASELXSFP(4), fiber100BASELHSFP(5), fiber100BASEZXSFP(6), fiber100CopperSFP(7), fiber1000BASEGTSFP(8), fiber1000BASESXSFP(9), fiber1000BASELXSFP(10), fiber1000BASELHSFP(11), fiber1000BASEZXSFP(12), fiber1000CopperSFP(13), fiber10GCopperSFPPlus(14), fiber10GBASESRSFPPlus(15), fiber10GBASELRSFPPlus(16), fiber10GBASEERSFPPlus(17), fiber10GBASEZRSFPPlus(18), fiber10GCopperXFP(19), fiber10GBASESRXFP(20), fiber10GBASELRXFP(21), fiber10GBASEERXFP(22), fiber10GBASEZRXFP(23), fiber40GActiveCableQSFPPlus(24), fiber40GLR4QSFPPlus(25), fiber40GCopperQSFPPlus(26), fiber40GSR4QSFPPlus(27), fiber2500CopperSFP(28), fiberFC16G(29), fiberFC8G(30), fiberFC4G(31), fiberFC2G(32), fiber10GActiveCableSFPPlus(33), fiber40GER4QSFPPlus(34), fiber40GZR4QSFPPlus(35), fiber100GCABLEQSFP28(36), fiber100GLR4QSFP28(37), fiber100GSR4QSFP28(38), fiber100GER4QSFP28(39), fiber100GZR4QSFP28(40), fiber100GCR4QSFP28(41), fiber100GPSM4QSFP28(42), fiber25GSRSFP28 (43), fiber25GLRSFP28 (44), fiber25GERSFP28 (45), fiber25GZRSFP28 (46), fiber25GCOPPERSFP28 (47), fiber25GACTIVECABLESFP28 (48), fiber100GiLR4QSFP28(49) } MAX-ACCESS read-only STATUS current DESCRIPTION "Transceiver type of the Fiber module insered into the port." ::= { fsFiberEntry 3 } fsFiberConnectorType OBJECT-TYPE SYNTAX INTEGER { meaningless(0), unknownorunspecified(1), vendorspecific(2), sc(3), fiberChannelStyle1CopperConnector(4), fiberChannelStyle2CopperConnector(5), bncortnc(6), fiberChannelCoaxialHeaders(7), fiberJack(8), lc(9), mtrj(10), mu(11), sg(12), opticalPigtail(13), hssdcII(14), copperPigtail(15), mpo(16), rj45(17), noSparableConnector(18) } MAX-ACCESS read-only STATUS current DESCRIPTION "Connector type of the Fiber module insered into the port. If the transceiver type of Fiber module is unknown(1), then this object contains a zero value." ::= { fsFiberEntry 4 } fsFiberWavelength OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of wavelength of the Fiber module insered into the port. If the transceiver type of Fiber module is either fiber100CopperSFP(7) or fiber1000CopperSFP(13) (or fiber10GCopperSFPPlus(14), or fiber10GCopperXFP(19), or fiber40GCopperQSFPPlus(26), or fiber2500CopperSFP(28), or unknown(1)), then this object contains a zero value." ::= { fsFiberEntry 5 } fsFiberTransferDistanceSMF OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber for. The value is in units of kilometers. A value of zero means that the transceiver does not support single mode fiber." ::= { fsFiberEntry 6 } fsFiberTransferDistance62point5umOM1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 62.5 micron multimode (200 MHz*Km at 850 nm, 500 MHz*Km at 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+." ::= { fsFiberEntry 7 } fsFiberTransferDistance62point5um OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 62.5 micron core multimode (200 MHz*Km at 850 nm, 500 MHz*Km at 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the Fiber module type is not XFP." ::= { fsFiberEntry 8 } fsFiberTransferDistance50umOM2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode (500 MHz*Km at 850 nm for SFP module or at 850 nm and 1310 nm for QSFP+ module) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+." ::= { fsFiberEntry 9 } fsFiberTransferDistance50um OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron core multimode (500 MHz*Km at 850 nm and 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron core multimode fiber or the Fiber module type is not XFP." ::= { fsFiberEntry 10 } fsFiberTransferDistance50umOM3 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode OM3(2000 MHz*Km) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+." ::= { fsFiberEntry 11 } fsFiberTransferDistanceEBW50um OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 2000 MHz*Km (850nm) extended bandwidth 50 micron core multimode fiber. The value is in units of meters. A value of zero means that the transceiver does not support extended bandwidth 50 micron multimode fiber or the Fiber module type is not XFP." ::= { fsFiberEntry 12 } fsFiberTransferDistanceCopper OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using copper cables. The value is in units of meters. A value of zero means that the transceiver does not support copper cables or the Fiber module type is neither SFP/SFP+ nor XFP." ::= { fsFiberEntry 13 } fsFiberTransferDistanceCableAssembly OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of transfer distance of the Fiber module insered into the port. This value specifies the link length of the Cable assembly passive. The value is in units of meters. A value of zero means that the transceiver is not a cable assemblyor or the Fiber module type is not QSFP+." ::= { fsFiberEntry 14 } fsFiberDDMSupportStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates that whether the Digital Diagnostic Monitors is implemeted." ::= { fsFiberEntry 15 } fsFiberSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The serial number of the Fiber module insered into the port." ::= { fsFiberEntry 16 } fsFiberTemp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature of the Fiber module insered into the port. The value is in units of degrees Celsius. If the fsFiberDDMSupportStatus is false, the temperature value is 0." ::= { fsFiberEntry 17 } fsFiberTempStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the temperature of the Fiber module is in the normal level. The status warning(3) indicates that the temperature of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the temperature of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1)." ::= { fsFiberEntry 18 } fsFiberVoltage OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The voltage of the Fiber module insered into the port. The value is in units of mVolts. If the fsFiberDDMSupportStatus is false, the voltage value is 0." ::= { fsFiberEntry 19 } fsFiberVoltageStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the voltage of the Fiber module is in the normal level. The status warning(3) indicates that the voltage of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the voltage of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1)." ::= { fsFiberEntry 20 } fsFiberBias OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The bias of the Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the bias value is 0." ::= { fsFiberEntry 21 } fsFiberBiasStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the bias of the Fiber module is in the normal level. The status warning(3) indicates that the bias of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1)." ::= { fsFiberEntry 22 } fsFiberChannel1Bias OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The bias in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 1 is 0." ::= { fsFiberEntry 23 } fsFiberChannel1BiasStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the bias in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 1 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 24 } fsFiberChannel2Bias OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The bias in Channel 2 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 2 is 0." ::= { fsFiberEntry 25 } fsFiberChannel2BiasStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the bias in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 2 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 26 } fsFiberChannel3Bias OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The bias in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 3 is 0." ::= { fsFiberEntry 27 } fsFiberChannel3BiasStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the bias in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 3 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 28 } fsFiberChannel4Bias OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The bias in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 4 is 0." ::= { fsFiberEntry 29 } fsFiberChannel4BiasStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the bias in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 4 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 30 } fsFiberRXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Rx power value is -100(means that the value is invalid)." ::= { fsFiberEntry 31 } fsFiberRXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Rx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the decimal part of Rx power value is -100(means that the value is invalid)." ::= { fsFiberEntry 32 } fsFiberRXpowertype OBJECT-TYPE SYNTAX INTEGER { unknown(1), average(2), oma(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value indicates whether the received power measurement represents average input optical power(2) or oma(3). If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP (or not QSFP+), the value is unknown(1)." ::= { fsFiberEntry 33 } fsFiberRXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Rx power of the Fiber module is in the normal level. The status warning(3) indicates that the Rx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1)." ::= { fsFiberEntry 34 } fsFiberChannel1RXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -100(means the value is invalid)." ::= { fsFiberEntry 35 } fsFiberChannel1RXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 1 is -100(means the value is invalid)." ::= { fsFiberEntry 36 } fsFiberChannel1RXpowertype OBJECT-TYPE SYNTAX INTEGER { unknown(1), average(2), oma(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 1 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1)." ::= { fsFiberEntry 37 } fsFiberChannel1RXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Rx power in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 1 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 38 } fsFiberChannel2RXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -100(means the value is invalid)." ::= { fsFiberEntry 39 } fsFiberChannel2RXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 2 is -100(means the value is invalid)." ::= { fsFiberEntry 40 } fsFiberChannel2RXpowertype OBJECT-TYPE SYNTAX INTEGER { unknown(1), average(2), oma(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 2 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1)." ::= { fsFiberEntry 41 } fsFiberChannel2RXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Rx power in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 2 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 42 } fsFiberChannel3RXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 3 is -100(means the value is invalid)." ::= { fsFiberEntry 43 } fsFiberChannel3RXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 3 is -100(means the value is invalid)." ::= { fsFiberEntry 44 } fsFiberChannel3RXpowertype OBJECT-TYPE SYNTAX INTEGER { unknown(1), average(2), oma(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 3 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1)." ::= { fsFiberEntry 45 } fsFiberChannel3RXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Rx power in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 3 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 46 } fsFiberChannel4RXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 4 is -100(means the value is invalid)." ::= { fsFiberEntry 47 } fsFiberChannel4RXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 4 is -100(means the value is invalid)." ::= { fsFiberEntry 48 } fsFiberChannel4RXpowertype OBJECT-TYPE SYNTAX INTEGER { unknown(1), average(2), oma(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 4 of QSFP+. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1)." ::= { fsFiberEntry 49 } fsFiberChannel4RXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Rx power in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 4 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 50 } fsFiberTXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Tx power value is -100(means that the value is invalid)." ::= { fsFiberEntry 51 } fsFiberTXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Tx power of the Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the decimal part of Tx power value is -100(means that the value is invalid)." ::= { fsFiberEntry 52 } fsFiberTXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Tx power of the Fiber module is in the normal level. The status warning(3) indicates that the Tx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power of the Fiber module exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1)." ::= { fsFiberEntry 53 } fsFiberChannel1TXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -100(means the value is invalid)." ::= { fsFiberEntry 54 } fsFiberChannel1TXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 1 is -100(means the value is invalid)." ::= { fsFiberEntry 55 } fsFiberChannel1TXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Tx power in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 1 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 56 } fsFiberChannel2TXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -100(means the value is invalid)." ::= { fsFiberEntry 57 } fsFiberChannel2TXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 2 is -100(means the value is invalid)." ::= { fsFiberEntry 58 } fsFiberChannel2TXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Tx power in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 2 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 59 } fsFiberChannel3TXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 3 is -100(means the value is invalid)." ::= { fsFiberEntry 60 } fsFiberChannel3TXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 3 is -100(means the value is invalid)." ::= { fsFiberEntry 61 } fsFiberChannel3TXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Tx power in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 3 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 62 } fsFiberChannel4TXpowerIntegerpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 4 is -100(means the value is invalid)." ::= { fsFiberEntry 63 } fsFiberChannel4TXpowerDecimalpart OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The decimal part of Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 4 is -100(means the value is invalid)." ::= { fsFiberEntry 64 } fsFiberChannel4TXpowerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), warning(3), alarm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status ok(2) indicates that the Tx power in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 4 exceeds high alarm level or is below low alarm level. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1)." ::= { fsFiberEntry 65 } fsFiberRXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 66 } fsFiberChannel1RXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 67 } fsFiberChannel2RXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 68 } fsFiberChannel3RXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 69 } fsFiberChannel4RXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 70 } fsFiberTXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 71 } fsFiberChannel1TXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 72 } fsFiberChannel2TXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 73 } fsFiberChannel3TXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 74 } fsFiberChannel4TXpowerSign OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0." ::= { fsFiberEntry 75 } fsFiberRXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer of Rx power of the Fiber module insered into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Rx power value is -10000(means that the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 76 } fsFiberChannel1RXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 1 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 77 } fsFiberChannel2RXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 1 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 78 } fsFiberChannel3RXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 3 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 3 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 79 } fsFiberChannel4RXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Rx power in Channel 4 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 4 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 80 } fsFiberTXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power of the Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Tx power value is -10000(means that the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 81 } fsFiberChannel1TXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 1 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 82 } fsFiberChannel2TXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 1 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 83 } fsFiberChannel3TXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 3 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 3 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 84 } fsFiberChannel4TXpowerInteger OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The integer part of Tx power in Channel 4 of the QSFP+ Fiber module inserted into the port. The value is in units of 0.01 dbm. If the fsFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 4 is -10000(means the value is invalid). Added by Observium Developers." ::= { fsFiberEntry 85 } fsFiberVendorTable OBJECT-TYPE SYNTAX SEQUENCE OF FSFiberVendorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Vendor info entries." ::= { fsFiberMIBObjects 2 } fsFiberVendorEntry OBJECT-TYPE SYNTAX FSFiberVendorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains Vendor info." INDEX { fsFiberVendorPortIndex } ::= { fsFiberVendorTable 1 } FSFiberVendorEntry ::= SEQUENCE { fsFiberVendorPortIndex IfIndex, fsFiberVendorName DisplayString, fsFiberVendorOUI DisplayString, fsFiberVendorPN DisplayString, fsFiberVendorRev DisplayString, fsFiberVendorDate DisplayString, fsFiberVendorEncoding DisplayString } fsFiberVendorPortIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The port index of Vendor info ." ::= { fsFiberVendorEntry 1 } fsFiberVendorName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The description of vendor name." ::= { fsFiberVendorEntry 2 } fsFiberVendorOUI OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Added by Observium developers" ::= { fsFiberVendorEntry 3 } fsFiberVendorPN OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Added by Observium developers" ::= { fsFiberVendorEntry 4 } fsFiberVendorRev OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Added by Observium developers" ::= { fsFiberVendorEntry 5 } fsFiberVendorDate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Added by Observium developers" ::= { fsFiberVendorEntry 6 } fsFiberVendorEncoding OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Added by Observium developers" ::= { fsFiberVendorEntry 7 } fsFiberAntifakeMIBTraps OBJECT IDENTIFIER ::= { fsFiberMIB 2 } fsFiberAntifakeIntfNameDesc OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The description of the interface." ::= { fsFiberAntifakeMIBTraps 1 } fsFiberAntifakeSerialNumberDesc OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The description of the serial number of the fiber module." ::= { fsFiberAntifakeMIBTraps 2 } fsFiberAntifakeTrap NOTIFICATION-TYPE OBJECTS {fsFiberAntifakeIntfNameDesc, fsFiberAntifakeSerialNumberDesc} STATUS current DESCRIPTION "When detect the fiber module is not original fs fiber module, then this trap will be sent." ::= { fsFiberAntifakeMIBTraps 3 } fsFiberMIBConformance OBJECT IDENTIFIER ::= { fsFiberMIB 3 } fsFiberMIBCompliances OBJECT IDENTIFIER ::= { fsFiberMIBConformance 1 } fsFiberMIBGroups OBJECT IDENTIFIER ::= { fsFiberMIBConformance 2 } -- ---------------------------------------------------------- -- -- compliance statements -- ---------------------------------------------------------- -- fsFiberMIBConpliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the FS Fiber MIB" MODULE -- this module MANDATORY-GROUPS { fsFiberMIBGroup } GROUP fsFiberAntifakeIntfNameDescGroup DESCRIPTION "This group is mandatory only for those system which support fiber antifake notification." GROUP fsFiberAntifakeSerialNumberDescGroup DESCRIPTION "This group is mandatory only for those system which support fiber antifake notification." ::= { fsFiberMIBCompliances 1 } fsFiberMIBGroup OBJECT-GROUP OBJECTS { fsFiberPortDescr, fsFiberTransceiverType, fsFiberConnectorType, fsFiberWavelength, fsFiberTransferDistanceSMF, fsFiberTransferDistance62point5umOM1, fsFiberTransferDistance62point5um, fsFiberTransferDistance50umOM2, fsFiberTransferDistance50um, fsFiberTransferDistance50umOM3, fsFiberTransferDistanceEBW50um, fsFiberTransferDistanceCopper, fsFiberTransferDistanceCableAssembly, fsFiberDDMSupportStatus, fsFiberSerialNumber, fsFiberTemp, fsFiberTempStatus, fsFiberVoltage, fsFiberVoltageStatus, fsFiberBias, fsFiberBiasStatus, fsFiberChannel1Bias, fsFiberChannel1BiasStatus, fsFiberChannel2Bias, fsFiberChannel2BiasStatus, fsFiberChannel3Bias, fsFiberChannel3BiasStatus, fsFiberChannel4Bias, fsFiberChannel4BiasStatus, fsFiberRXpowerIntegerpart, fsFiberRXpowerDecimalpart, fsFiberRXpowertype, fsFiberRXpowerStatus, fsFiberChannel1RXpowerIntegerpart, fsFiberChannel1RXpowerDecimalpart, fsFiberChannel1RXpowertype, fsFiberChannel1RXpowerStatus, fsFiberChannel2RXpowerIntegerpart, fsFiberChannel2RXpowerDecimalpart, fsFiberChannel2RXpowertype, fsFiberChannel2RXpowerStatus, fsFiberChannel3RXpowerIntegerpart, fsFiberChannel3RXpowerDecimalpart, fsFiberChannel3RXpowertype, fsFiberChannel3RXpowerStatus, fsFiberChannel4RXpowerIntegerpart, fsFiberChannel4RXpowerDecimalpart, fsFiberChannel4RXpowertype, fsFiberChannel4RXpowerStatus, fsFiberTXpowerIntegerpart, fsFiberTXpowerDecimalpart, fsFiberTXpowerStatus, fsFiberChannel1TXpowerIntegerpart, fsFiberChannel1TXpowerDecimalpart, fsFiberChannel1TXpowerStatus, fsFiberChannel2TXpowerIntegerpart, fsFiberChannel2TXpowerDecimalpart, fsFiberChannel2TXpowerStatus, fsFiberChannel3TXpowerIntegerpart, fsFiberChannel3TXpowerDecimalpart, fsFiberChannel3TXpowerStatus, fsFiberChannel4TXpowerIntegerpart, fsFiberChannel4TXpowerDecimalpart, fsFiberChannel4TXpowerStatus, fsFiberRXpowerSign, fsFiberChannel1RXpowerSign, fsFiberChannel2RXpowerSign, fsFiberChannel3RXpowerSign, fsFiberChannel4RXpowerSign, fsFiberTXpowerSign, fsFiberChannel1TXpowerSign, fsFiberChannel2TXpowerSign, fsFiberChannel3TXpowerSign, fsFiberChannel4TXpowerSign } STATUS current DESCRIPTION "A collection of objects providing Fiber managment." ::= { fsFiberMIBGroups 1 } fsFiberAntifakeIntfNameDescGroup OBJECT-GROUP OBJECTS {fsFiberAntifakeIntfNameDesc} STATUS current DESCRIPTION "Objects that providing a literal description of the interface." ::= { fsFiberMIBGroups 2 } fsFiberAntifakeSerialNumberDescGroup OBJECT-GROUP OBJECTS {fsFiberAntifakeSerialNumberDesc} STATUS current DESCRIPTION "Objects that providing a literal description of the fiber module serial number." ::= { fsFiberMIBGroups 3 } END