ENTERASYS-STATION-LOCATION-MIB DEFINITIONS ::= BEGIN -- -- enterasys-station-location-mib.txt -- -- Part Number: -- -- -- This module provides authoritative definitions for Extreme -- Networks' Station Location MIB. -- -- This module will be extended, as needed. -- Extreme Networks reserves the right to make changes in this -- specification and other information contained in this document -- without prior notice. The reader should consult Extreme Networks -- to determine whether any such changes have been made. -- -- In no event shall Extreme Networks be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Extreme -- Networks has been advised of, known, or should have known, the -- possibility of such damages. -- -- Extreme Networks grants vendors, end-users, and other interested -- parties a non-exclusive license to use this Specification in -- connection with the management of Extreme Networks products. -- Copyright May 2016 Extreme Networks, Inc. IMPORTS OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF Integer32, Unsigned32, OBJECT-TYPE, MODULE-IDENTITY FROM SNMPv2-SMI MacAddress, RowStatus, TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB etsysModules FROM ENTERASYS-MIB-NAMES; etsysStationLocationMIB MODULE-IDENTITY LAST-UPDATED "201605111936Z" -- Wed May 11 19:36 UTC 2016 ORGANIZATION "Extreme Networks" CONTACT-INFO "Postal: Extreme Networks, Inc. 145 Rio Robles San Jose, CA 95134 USA Phone: +1 408 579-2800 E-mail: support@extremenetworks.com WWW: http://www.extremenetworks.com" DESCRIPTION "This MIB provides an interface to manage the wireless station localization application. It allows configuration of the application as well retrieving information about location of managed Station that are associated to controller or are configured to be tracked even without being associated." REVISION "201605111936Z" -- Wed May 11 19:36 UTC 2016 DESCRIPTION "Added etsysPublishLocationUserId and etsysPublishLocationPassword to etsysPublishLocationURLTable." REVISION "201509101618Z" -- Thursday Sept 10 16:18 UTC 2015 DESCRIPTION "Added etsysLocationEngineTrackMode to etsysLocationConfiguration." REVISION "201406131610Z" -- Fri Jun 13 16:10 UTC 2014 DESCRIPTION "Added location batch report to provide a way for consumer programs to receive the list of the locations of all associated stations. Added etsysLocationEngineTrackAreaChange to etsysLocationConfiguration." REVISION "201304181520Z" -- Thu Apr 18 15:20 UTC 2013 DESCRIPTION "The initial version of this MIB module." ::= { etsysModules 98 } -- ------------------------------------------------------------- -- Textual conventions -- ------------------------------------------------------------- FloorEnvironmentType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type of indoor construction materials used on its floor. openSpace(0): Indoor open space (halls, auditoriums) lightDivision(1): Office environment with light divisions (cubicles) dryWallsDivision(2): Office environment with dry walls divisions hardDivision(3): Office Environment with hard divisions (brick) interiorWalls(4): Interior Walls (need be defined in the floor plan) " SYNTAX INTEGER { openSpace(0), lightDivision(1), dryWallsDivision(2), hardDivision(3), interiorWalls(4) } -- ------------------------------------------------------------- -- MIB Objects -- ------------------------------------------------------------- etsysStationLocationMIBObjects OBJECT IDENTIFIER ::= { etsysStationLocationMIB 1 } etsysLocationConfiguration OBJECT IDENTIFIER ::= { etsysStationLocationMIBObjects 1 } etsysLocationEngineEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to true (1), enables the location engine to track stations, otherwise no station will be tracked." ::= { etsysLocationConfiguration 1 } etsysLocationEngineAutoTrkEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this variable is set to true and etsysLocationEngineEnable is set to true then all associated stations will be tracked up to the platform limit for location tracking." ::= { etsysLocationConfiguration 2 } etsysLocationEngineGlblAPHeight OBJECT-TYPE SYNTAX Unsigned32 (0..1000) UNITS "centimeters" MAX-ACCESS read-write STATUS current DESCRIPTION "Default height of access point to be used if the floor configuration has not provided any height for any AP servicing the floor. The range of height is 0 to 1000 in centimeters." ::= { etsysLocationConfiguration 3 } etsysLocationEngineGlobalEnv OBJECT-TYPE SYNTAX FloorEnvironmentType MAX-ACCESS read-write STATUS current DESCRIPTION "Type of indoor construction materials assumed when the floor plan does not specify the primary construction materials used on its floor." ::= { etsysLocationConfiguration 4 } -- ------------------------------------------------------------- -- The Location Floors Group -- ------------------------------------------------------------- etsysLocationFloors OBJECT IDENTIFIER ::= { etsysLocationConfiguration 5 } etsysLocationMaxFloorLimit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of floor plan files that can be stored and used on this controller." ::= { etsysLocationFloors 1 } etsysLocationFloorConfigured OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of floors that have been configured and currently used." ::= { etsysLocationFloors 2 } etsysFloorTable OBJECT-TYPE SYNTAX SEQUENCE OF EtsysFloorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that describes attributes of floors configured for use by the Location Engine." ::= { etsysLocationFloors 3 } etsysFloorEntry OBJECT-TYPE SYNTAX EtsysFloorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing a single floor in the location engine's database." INDEX { etsysFloorID } ::= { etsysFloorTable 1 } EtsysFloorEntry ::= SEQUENCE { etsysFloorID Unsigned32, etsysFloorRowStatus RowStatus, etsysFloorName SnmpAdminString, etsysFloorNumberOfAPs Unsigned32, etsysFloorWidth Unsigned32, etsysFloorLength Unsigned32, etsysFloorNumberOfCells Unsigned32, etsysFloorCellWidth Unsigned32, etsysFloorCellLength Unsigned32, etsysFloorEnvironment FloorEnvironmentType, etsysFloorHashString OCTET STRING } etsysFloorID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Floor ID associated to the floor. This index ranges from one to etsysLocationMaxFloorLimit. This ID persists over reboots and upgrades." ::= { etsysFloorEntry 1 } etsysFloorRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "RowStatus of the entry, though currently only deletion is allowed for this field." ::= { etsysFloorEntry 2 } etsysFloorName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Textual string identifying floor name. Supports UTF-8 character set, except Double Quotes and ASCII control characters." ::= { etsysFloorEntry 3 } etsysFloorNumberOfAPs OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Number of access point have been assigned to this floor to track stations on this floor." ::= { etsysFloorEntry 4 } etsysFloorWidth OBJECT-TYPE SYNTAX Unsigned32 UNITS "centimeters" MAX-ACCESS read-create STATUS current DESCRIPTION "Width of the floor in centimeters." ::= { etsysFloorEntry 5 } etsysFloorLength OBJECT-TYPE SYNTAX Unsigned32 UNITS "centimeters" MAX-ACCESS read-create STATUS current DESCRIPTION "Length of the floor in centimeters." ::= { etsysFloorEntry 6 } etsysFloorNumberOfCells OBJECT-TYPE SYNTAX Unsigned32 UNITS "centimeters" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of cells on this floor." ::= { etsysFloorEntry 7 } etsysFloorCellWidth OBJECT-TYPE SYNTAX Unsigned32 UNITS "centimeters" MAX-ACCESS read-create STATUS current DESCRIPTION "Width of each cell for this floor in centimeters." ::= { etsysFloorEntry 8 } etsysFloorCellLength OBJECT-TYPE SYNTAX Unsigned32 UNITS "centimeters" MAX-ACCESS read-create STATUS current DESCRIPTION "Length of each cell for this floor in centimeters." ::= { etsysFloorEntry 9 } etsysFloorEnvironment OBJECT-TYPE SYNTAX FloorEnvironmentType MAX-ACCESS read-create STATUS current DESCRIPTION "Type of propagation model for the floor." ::= { etsysFloorEntry 10 } etsysFloorHashString OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-create STATUS current DESCRIPTION "MD5 hash of the file as received during download." ::= { etsysFloorEntry 11 } -- ------------------------------------------------------------- -- The Location Stations Group -- ------------------------------------------------------------- etsysLocationStations OBJECT IDENTIFIER ::= { etsysLocationConfiguration 6 } etsysMaxTrackedStationLimit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of stations that this platform can track. Stations are tracked on the basis of either being associated to the controller or administratively added to the 'On-Demand Tracking' list " ::= { etsysLocationStations 1 } etsysMaxOnDemandStationLimit OBJECT-TYPE SYNTAX Unsigned32 (0..32) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of stations that can be configured to be tracked as on-demand basis." ::= { etsysLocationStations 2 } etsysOnDemandStationTable OBJECT-TYPE SYNTAX SEQUENCE OF EtsysOnDemandStationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of stations to be tracked by the Location Engine. Location tracking of a station may stop when it is removed from the list. The list is configured by the administrator and is used to reserve capacity to ensure that the addresses in the list are among those tracked by the location engine." ::= { etsysLocationStations 3 } etsysOnDemandStationEntry OBJECT-TYPE SYNTAX EtsysOnDemandStationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address of a single station to be tracked." INDEX { etsysOnDemandStationMAC } ::= { etsysOnDemandStationTable 1 } EtsysOnDemandStationEntry ::= SEQUENCE { etsysOnDemandStationMAC MacAddress, etsysOnDemandStationRowStatus RowStatus } etsysOnDemandStationMAC OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "MAC address of the station to be tracked." ::= { etsysOnDemandStationEntry 1 } etsysOnDemandStationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "RowStatus of the entry." ::= { etsysOnDemandStationEntry 2 } etsysLocationEngineTrackAreaChange OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to enable(1), the location engine will track the area changes, otherwise, the area information is determined by the associated AP." ::= { etsysLocationConfiguration 7 } etsysLocationEngineTrackMode OBJECT-TYPE SYNTAX INTEGER { trackClients(1), trackAll(2), trackNone(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "trackClients(1) : All associated stations will be tracked up to the platform limit. trackAll(2) : All Mac address will be tracked up to the platform limit. trackNone(3) : Location engine is tracking the on demand list only." ::= { etsysLocationConfiguration 8 } -- ------------------------------------------------------------- -- The Location Reports Group -- ------------------------------------------------------------- etsysLocationReports OBJECT IDENTIFIER ::= { etsysStationLocationMIBObjects 2 } etsysTrackedStationTable OBJECT-TYPE SYNTAX SEQUENCE OF EtsysTrackedStationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing information about tracked stations." ::= { etsysLocationReports 1 } etsysTrackedStationEntry OBJECT-TYPE SYNTAX EtsysTrackedStationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing the location of one tracked station." INDEX { etsysTrackedStationMAC } ::= { etsysTrackedStationTable 1 } EtsysTrackedStationEntry ::= SEQUENCE { etsysTrackedStationMAC MacAddress, etsysTrackedStationFloorID Unsigned32, etsysTrackedStationLocationType INTEGER, etsysTrackedStationReportingAPSN SnmpAdminString, etsysTrackedStationAPDistance Integer32 } etsysTrackedStationMAC OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "MAC address associated to the station that is being tracked." ::= { etsysTrackedStationEntry 1 } etsysTrackedStationFloorID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of the floor on which the station appears to be active." ::= { etsysTrackedStationEntry 2 } etsysTrackedStationLocationType OBJECT-TYPE SYNTAX INTEGER { unknown(0), rssBasedLocation(1), cellOfOrigin(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the type of location report for the station. The meaning of other fields in this table and the etsysLocationGridTable depend on the value of this object. If this object has a value of 'cellOfOrigin' then etsysStationLocnGridX and etsysStationLocationGridY will be set to -1 in the etsysStationLocationGridTable entry for this station." ::= { etsysTrackedStationEntry 3 } etsysTrackedStationReportingAPSN OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The serial number of the access point that reported an RSS value for the station. This object is meaningful only when the value of etsysTrackedStationLocationType is cellOfOrigin. The cell of origin method determines location based on the probable distance of the subject from a known location, in this case, the location of the AP that reported the RSS value. Cell of Origin is used when fewer than three APs report seeing the station at one time. If two APs report the station then the serial number of the AP reporting the strongest RSS is reported as the station's etsysTrackedStationReportingAPSN." ::= { etsysTrackedStationEntry 6 } etsysTrackedStationAPDistance OBJECT-TYPE SYNTAX Integer32 UNITS "meters" MAX-ACCESS read-only STATUS current DESCRIPTION "The distance (in meters) of the station from the access point with the serial number in etsysTrackedStationReportingAPSN. This object is meaningful only when the value of etsysTrackedStationLocationType is cellOfOrigin." ::= { etsysTrackedStationEntry 7 } etsysStationLocationGridTable OBJECT-TYPE SYNTAX SEQUENCE OF EtsysStationLocationGridEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "When the location type is rssBasedLocation it is likely that there will be a number of probable locations calculated for one station. This table lists the most recently rssBasedLocation-calculated probable locations of each tracked station. Each row of the table represents one probable location of one tracked station. The table is indexed by the subject station's MAC address and an internal identifier for the cell described by the entry. The cell is a cell on the floor identified by the etsysTrackedStationFloorID object in the etsysTrackedStationEntry for the subject station." ::= { etsysLocationReports 2 } etsysStationLocationGridEntry OBJECT-TYPE SYNTAX EtsysStationLocationGridEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "One entry in this table providing one of the possible location for the station with associated probability." INDEX { etsysTrackedStationMAC, etsysStationLocnGridIndex } ::= { etsysStationLocationGridTable 1 } EtsysStationLocationGridEntry ::= SEQUENCE { etsysStationLocnGridIndex Unsigned32, etsysStationLocnGridX Integer32, etsysStationLocnGridY Integer32, etsysStationLocnGridProbability Integer32 } etsysStationLocnGridIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Internally assigned number to those location starting from one to the maximum number of reported locations. This field has no meaning by itself." ::= { etsysStationLocationGridEntry 1 } etsysStationLocnGridX OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "X-coordinate associated to the location of the reported cell." ::= { etsysStationLocationGridEntry 2 } etsysStationLocnGridY OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Y-coordinate associated to the location of the reported cell." ::= { etsysStationLocationGridEntry 3 } etsysStationLocnGridProbability OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Estimated percentage chance that the station is actually located in the identified cell. A value of zero means the location is not known." ::= { etsysStationLocationGridEntry 4 } -- ------------------------------------------------------------- -- The Location Batch Reports Group -- ------------------------------------------------------------- etsysLocationBatchReport OBJECT IDENTIFIER ::= { etsysStationLocationMIBObjects 3 } etsysLocationBatchReportEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to true (1) enables the location batch reporting feature." ::= { etsysLocationBatchReport 1 } etsysLocationBatchReportFrequency OBJECT-TYPE SYNTAX Unsigned32 (60..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The report frequency setting in seconds. Currently 60, 120, 300, 600, 1200, 1800, 3600, 7200 and 14400 seconds are supported. Other values are un-supported and will be rejected." ::= { etsysLocationBatchReport 2 } etsysPublishLocationURLMaxEntries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of URLs supported by the controller." ::= { etsysLocationBatchReport 3 } etsysPublishLocationURLNumEntries OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of entries in the etsysPublishLocationURLTable." ::= { etsysLocationBatchReport 4 } etsysPublishLocationURLTable OBJECT-TYPE SYNTAX SEQUENCE OF EtsysPublishLocationURLEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing destination URLs to which the controller posts location information. Only http and https are supported." ::= { etsysLocationBatchReport 5 } etsysPublishLocationURLEntry OBJECT-TYPE SYNTAX EtsysPublishLocationURLEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing the destination URL." INDEX { etsysPublishLocationIndex } ::= { etsysPublishLocationURLTable 1 } EtsysPublishLocationURLEntry ::= SEQUENCE { etsysPublishLocationIndex Unsigned32, etsysPublishLocationURL OCTET STRING, etsysPublishLocationRowStatus RowStatus, etsysPublishLocationUserId SnmpAdminString, etsysPublishLocationPassword SnmpAdminString } etsysPublishLocationIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for a configured destination URL." ::= { etsysPublishLocationURLEntry 1 } etsysPublishLocationURL OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..512)) MAX-ACCESS read-create STATUS current DESCRIPTION "The URL of the destination to which a report is pushed." DEFVAL { ''H } ::= { etsysPublishLocationURLEntry 2 } etsysPublishLocationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "A control that will allow one entry to be added, activated, deactivated, or removed from the table." ::= { etsysPublishLocationURLEntry 3 } etsysPublishLocationUserId OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The login name for the destination URL server." ::= { etsysPublishLocationURLEntry 4 } etsysPublishLocationPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The password for the destination URL server. On a read, a dummy (not real password) will be returned." ::= { etsysPublishLocationURLEntry 5 } etsysLocationBatchReportDimensionUnit OBJECT-TYPE SYNTAX INTEGER { meter(0), feet(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The units for reported x and y location coordinates. " ::= { etsysLocationBatchReport 6 } -- ------------------------------------------------------------- -- Conformance Information -- ------------------------------------------------------------- etsysStationLocationConformance OBJECT IDENTIFIER ::= { etsysStationLocationMIB 2 } etsysStationLocationGroups OBJECT IDENTIFIER ::= { etsysStationLocationConformance 1 } etsysStationLocationCompliances OBJECT IDENTIFIER ::= { etsysStationLocationConformance 2 } -- ------------------------------------------------------------- -- Units of conformance -- ------------------------------------------------------------- etsysLocationEngineGlobalGroup OBJECT-GROUP OBJECTS { etsysLocationEngineEnable, etsysLocationEngineAutoTrkEnable, etsysLocationEngineGlblAPHeight, etsysLocationEngineGlobalEnv } STATUS deprecated DESCRIPTION "Objects defining configuration attributes of a location tracking components." ::= { etsysStationLocationGroups 1 } etsysFloorGroup OBJECT-GROUP OBJECTS { etsysFloorRowStatus, etsysFloorName, etsysFloorNumberOfAPs, etsysFloorWidth, etsysFloorLength, etsysFloorNumberOfCells, etsysFloorCellWidth, etsysFloorCellLength, etsysFloorHashString, etsysFloorEnvironment, etsysLocationMaxFloorLimit, etsysLocationFloorConfigured } STATUS current DESCRIPTION "List of objects that defines attributes of a configured floor." ::= { etsysStationLocationGroups 2 } etsysOnDemandStationsGroup OBJECT-GROUP OBJECTS { etsysOnDemandStationRowStatus } STATUS current DESCRIPTION "List of objects that define attribute of a on-demand stations to be tracked." ::= { etsysStationLocationGroups 3 } etsysTrackedStationsGroup OBJECT-GROUP OBJECTS { etsysTrackedStationFloorID, etsysTrackedStationLocationType, etsysTrackedStationReportingAPSN, etsysTrackedStationAPDistance, etsysStationLocnGridX, etsysStationLocnGridY, etsysStationLocnGridProbability, etsysMaxOnDemandStationLimit, etsysMaxTrackedStationLimit } STATUS current DESCRIPTION "List of objects that define a tracked stations attributes." ::= { etsysStationLocationGroups 4 } etsysLocationBatchReportGroup OBJECT-GROUP OBJECTS { etsysLocationBatchReportEnable, etsysLocationBatchReportFrequency, etsysLocationBatchReportDimensionUnit, etsysPublishLocationURLMaxEntries, etsysPublishLocationURLNumEntries, etsysPublishLocationURL, etsysPublishLocationRowStatus } STATUS deprecated DESCRIPTION "List of objects that define location batch reporting attributes." ::= { etsysStationLocationGroups 5 } etsysLocationEngineGlobalGroup2 OBJECT-GROUP OBJECTS { etsysLocationEngineEnable, etsysLocationEngineAutoTrkEnable, etsysLocationEngineGlblAPHeight, etsysLocationEngineGlobalEnv, etsysLocationEngineTrackAreaChange } STATUS deprecated DESCRIPTION "Objects defining configuration attributes of a location tracking components." ::= { etsysStationLocationGroups 6 } etsysLocationEngineGlobalGroup3 OBJECT-GROUP OBJECTS { etsysLocationEngineEnable, etsysLocationEngineAutoTrkEnable, etsysLocationEngineGlblAPHeight, etsysLocationEngineGlobalEnv, etsysLocationEngineTrackAreaChange, etsysLocationEngineTrackMode } STATUS current DESCRIPTION "Objects defining configuration attributes of a location tracking components." ::= { etsysStationLocationGroups 7 } etsysLocationBatchReportGroup2 OBJECT-GROUP OBJECTS { etsysLocationBatchReportEnable, etsysLocationBatchReportFrequency, etsysLocationBatchReportDimensionUnit, etsysPublishLocationURLMaxEntries, etsysPublishLocationURLNumEntries, etsysPublishLocationURL, etsysPublishLocationRowStatus, etsysPublishLocationUserId, etsysPublishLocationPassword } STATUS current DESCRIPTION "List of objects that define location batch reporting attributes." ::= { etsysStationLocationGroups 8 } -- ------------------------------------------------------------- -- Compliance statements -- ------------------------------------------------------------- etsysStationLocationCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "This group is mandatory for all devices that support reporting and configuration of station location." MODULE -- this module MANDATORY-GROUPS { etsysLocationEngineGlobalGroup, etsysFloorGroup, etsysOnDemandStationsGroup, etsysTrackedStationsGroup } ::= { etsysStationLocationCompliances 1 } etsysStationLocationCompliance2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "This group is mandatory for all devices that support reporting and configuration of station location." MODULE -- this module MANDATORY-GROUPS { etsysLocationEngineGlobalGroup2, etsysFloorGroup, etsysOnDemandStationsGroup, etsysTrackedStationsGroup, etsysLocationBatchReportGroup } ::= { etsysStationLocationCompliances 2 } etsysStationLocationCompliance3 MODULE-COMPLIANCE STATUS current DESCRIPTION "This group is mandatory for all devices that support reporting and configuration of station location." MODULE -- this module MANDATORY-GROUPS { etsysLocationEngineGlobalGroup3, etsysFloorGroup, etsysOnDemandStationsGroup, etsysTrackedStationsGroup, etsysLocationBatchReportGroup2 } ::= { etsysStationLocationCompliances 3 } END