--BESTPOWER-MIB { iso(1) org(3) dod(6) internet(1) private(4) -- enterprises(1) bestpower(2947) } --Last Modification 03/23/00 by Steve Van Duser --Contributing Authors: Steve Van Duser BEST POWER -- Jamie Krueger BEST POWER -- Brian Young BEST POWER -- RFC1628 model for a UPS MIB BESTPOWER-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises, IpAddress, Gauge FROM RFC1155-SMI DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215; --textual conventions NonNegativeInteger ::= INTEGER PositiveInteger ::= INTEGER -- TimeStamp ::= TimeTicks bestPower OBJECT IDENTIFIER ::= { enterprises 2947 } bestLink OBJECT IDENTIFIER ::= { bestPower 1 } upsIdent OBJECT IDENTIFIER ::= { bestLink 1 } upsBattery OBJECT IDENTIFIER ::= { bestLink 2 } upsInput OBJECT IDENTIFIER ::= { bestLink 3 } upsOutput OBJECT IDENTIFIER ::= { bestLink 4 } upsConfig OBJECT IDENTIFIER ::= { bestLink 5 } upsControl OBJECT IDENTIFIER ::= { bestLink 6 } upsTest OBJECT IDENTIFIER ::= { bestLink 7 } upsAlarm OBJECT IDENTIFIER ::= { bestLink 8 } upsBypass OBJECT IDENTIFIER ::= { bestLink 9 } -- Ident Group upsIdentUpsName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..19)) ACCESS read-only STATUS mandatory DESCRIPTION "An ID string identifying the Family of UPS." ::= { upsIdent 1 } upsIdentModel OBJECT-TYPE SYNTAX DisplayString (SIZE (0..29)) ACCESS read-only STATUS mandatory DESCRIPTION "The UPS model name (example: 'FE500VA')." ::= { upsIdent 2 } upsIdentVARating OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The capacity rating of the UPS expressed in VoltAmperes(VA)." ::= { upsIdent 3 } upsIdentUpsType OBJECT-TYPE SYNTAX INTEGER { standby(1), online(2), offline(3), lineInterative(4), 3PhaseDC(5), 3PhaseLI(6), hybrid(7) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of UPS." ::= { upsIdent 4 } upsIdentUpsSerialNumber OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A unique identification number provided by the factory." ::= { upsIdent 5 } upsIdentFirmwareRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..19)) ACCESS read-only STATUS mandatory DESCRIPTION "The firmware revision of the UPS." ::= { upsIdent 7 } upsIdentInstallationDate OBJECT-TYPE SYNTAX DisplayString (SIZE(6..10)) ACCESS read-write STATUS mandatory DESCRIPTION "The date when the UPS was installed in mm/dd/yyyy format." ::= { upsIdent 8 } -- the upsBattery group upsBatteryStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), upsOnBattery(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of the inverter ." ::= { upsBattery 1 } upsBatteryTimeOnBattery OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The elapsed time in seconds since the UPS has switched to battery power." ::= { upsBattery 2 } upsBatteryRuntimeRemaining OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The remaining time in minutes that the UPS will be able to run on battery power." ::= { upsBattery 3 } upsBatteryVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS battery voltage expressed in 1/10 VDC." ::= { upsBattery 4 } upsBatteryCurrent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The battery current expressed in 1/10 ADC." ::= { upsBattery 5 } upsBatteryTemperature OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The internal UPS temperature expressed in 1/10 degree C." ::= { upsBattery 6 } upsBatteryLastReplaceDate OBJECT-TYPE SYNTAX DisplayString (SIZE(6..10)) ACCESS read-write STATUS mandatory DESCRIPTION "The date when the UPS system's batteries were last replaced in mm/dd/yyyy format. When the UPS batteries are replaced, this value should be reset by the administrator." ::= { upsBattery 7 } upsBatteryCellVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS battery cell voltage expressed in 1/100 VDC." ::= { upsBattery 8 } upsBatteryPositiveVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS battery voltage measured from the most postive point in the battery string to the common reference point. The value is expressed in 1/10 VDC." ::= { upsBattery 9 } upsBatteryNegativeVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS battery voltage measured from the most negative point in the battery string to the common reference point. The value is expressed in 1/10 VDC." ::= { upsBattery 10 } -- the upsInput group --upsInputPhase OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The AC input phase." -- ::= { upsInput 1 } upsInputFrequency OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The utility line frequency in 1/10 Hz." ::= { upsInput 2 } upsInputVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The utility line voltage in 1/10 VAC." ::= { upsInput 3 } upsInputCurrent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The utility line current in 1/10 Ampere AC." ::= { upsInput 4 } upsInput3PhaseCurrent OBJECT IDENTIFIER ::= { upsInput 6 } upsInputCurrentL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input current on L1." ::= { upsInput3PhaseCurrent 1 } upsInputCurrentL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input current on L2." ::= { upsInput3PhaseCurrent 2 } upsInputCurrentL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input current on L3." ::= { upsInput3PhaseCurrent 3 } upsInput3PhaseVoltageLtoN OBJECT IDENTIFIER ::= { upsInput 7 } upsInputVoltageL1toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input voltage from L1 to Neutral." ::= { upsInput3PhaseVoltageLtoN 1 } upsInputVoltageL2toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input voltage from L2 to Neutral." ::= { upsInput3PhaseVoltageLtoN 2 } upsInputVoltageL3toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input voltage from L3 to Neutral." ::= { upsInput3PhaseVoltageLtoN 3 } upsInput3PhaseVoltageLtoL OBJECT IDENTIFIER ::= { upsInput 8 } upsInputVoltageL1toL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input voltage from L1 to L2." ::= { upsInput3PhaseVoltageLtoL 1 } upsInputVoltageL2toL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input voltage from L2 to L3." ::= { upsInput3PhaseVoltageLtoL 2 } upsInputVoltageL3toL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present input voltage from L3 to L1." ::= { upsInput3PhaseVoltageLtoL 3 } -- the upsOutput group --upsOutputStatus OBJECT-TYPE -- SYNTAX INTEGER { -- unknown(1), -- onLine(2), -- onBattery(3), -- onBypass(4) -- } -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The current state of the UPS. If the UPS is unable -- to determine its state, this variable is set -- to unknown(1)." -- ::= { upsOutput 1 } --upsOutputPhase OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "The output phase." -- ::= { upsOutput 2 } upsOutputFrequency OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The output frequency of the UPS expressed in 1/10 Hz." ::= { upsOutput 3 } upsOutputVoltage OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The output voltage of the UPS expressed in 1/10 VAC." ::= { upsOutput 4 } upsOutputCurrent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The output current of the UPS expressed in 1/10 AC Amperes." ::= { upsOutput 5 } upsOutputTruePower OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The true output power of the UPS expressed in 1/100 Watts." ::= { upsOutput 6 } upsOutputApparentPower OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The apparent output power of the UPS expressed in 1/100 VoltAmperes(VA)." ::= { upsOutput 7 } upsOutputPowerFactor OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The output powerfactor of the UPS expressed in +/- 1/100 units deviating from 1." ::= { upsOutput 8 } upsOutputPercentFullLoad OBJECT-TYPE SYNTAX INTEGER -- UNITS percent ACCESS read-only STATUS mandatory DESCRIPTION "The percentage of the total UPS power capacity being used expressed in % of 100." ::= { upsOutput 9 } upsOutput3PhaseVoltageLtoN OBJECT IDENTIFIER ::= { upsOutput 10 } upsOutputVoltageL1toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output voltage from L1 to Neutral." ::= { upsOutput3PhaseVoltageLtoN 1 } upsOutputVoltageL2toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output voltage from L2 to Neutral." ::= { upsOutput3PhaseVoltageLtoN 2 } upsOutputVoltageL3toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output voltage from L3 to Neutral." ::= { upsOutput3PhaseVoltageLtoN 3 } upsOutput3PhaseVoltageLtoL OBJECT IDENTIFIER ::= { upsOutput 11 } upsOutputVoltageL1toL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output voltage from L1 to L2." ::= { upsOutput3PhaseVoltageLtoL 1 } upsOutputVoltageL2toL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output voltage from L2 to L3." ::= { upsOutput3PhaseVoltageLtoL 2 } upsOutputVoltageL3toL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output voltage from L3 to L1." ::= { upsOutput3PhaseVoltageLtoL 3 } upsOutput3PhaseCurrent OBJECT IDENTIFIER ::= { upsOutput 12 } upsOutputCurrentL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output current on L1." ::= { upsOutput3PhaseCurrent 1 } upsOutputCurrentL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output current on L2." ::= { upsOutput3PhaseCurrent 2 } upsOutputCurrentL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output current on L3." ::= { upsOutput3PhaseCurrent 3 } upsOutput3PhaseApparentPower OBJECT IDENTIFIER ::= { upsOutput 13 } upsOutputApparentPowerL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output ApparentPower on L1." ::= { upsOutput3PhaseApparentPower 1 } upsOutputApparentPowerL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output ApparentPower on L2." ::= { upsOutput3PhaseApparentPower 2 } upsOutputApparentPowerL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output ApparentPower on L3." ::= { upsOutput3PhaseApparentPower 3 } upsOutput3PhaseTruePower OBJECT IDENTIFIER ::= { upsOutput 14 } upsOutputTruePowerL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output TruePower on L1." ::= { upsOutput3PhaseTruePower 1 } upsOutputTruePowerL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output TruePower on L2." ::= { upsOutput3PhaseTruePower 2 } upsOutputTruePowerL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output TruePower on L3." ::= { upsOutput3PhaseTruePower 3 } upsOutput3PhasePowerFactor OBJECT IDENTIFIER ::= { upsOutput 15 } upsOutputPowerFactorL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output PowerFactor on L1." ::= { upsOutput3PhasePowerFactor 1 } upsOutputPowerFactorL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output PowerFactor on L2." ::= { upsOutput3PhasePowerFactor 2 } upsOutputPowerFactorL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output PowerFactor on L3." ::= { upsOutput3PhasePowerFactor 3 } upsOutput3PhasePercentLoad OBJECT IDENTIFIER ::= { upsOutput 16 } upsOutputPercentLoadL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output PercentLoad on L1." ::= { upsOutput3PhasePercentLoad 1 } upsOutputPercentLoadL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output PercentLoad on L2." ::= { upsOutput3PhasePercentLoad 2 } upsOutputPercentLoadL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Output PercentLoad on L3." ::= { upsOutput3PhasePercentLoad 3 } -- the upsBypass group upsBypassStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), upsOnBypass(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of the bypass mode." ::= { upsBypass 1 } upsBypass3PhaseVoltageLtoN OBJECT IDENTIFIER ::= { upsBypass 2 } upsBypassVoltageL1toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Bypass voltage from L1 to Neutral." ::= { upsBypass3PhaseVoltageLtoN 1 } upsBypassVoltageL2toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Bypass voltage from L2 to Neutral." ::= { upsBypass3PhaseVoltageLtoN 2 } upsBypassVoltageL3toN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Bypass voltage from L3 to Neutral." ::= { upsBypass3PhaseVoltageLtoN 3 } upsBypass3PhaseVoltageLtoL OBJECT IDENTIFIER ::= { upsBypass 3 } upsBypassVoltageL1toL2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Bypass voltage from L1 to L2." ::= { upsBypass3PhaseVoltageLtoL 1 } upsBypassVoltageL2toL3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Bypass voltage from L2 to L3." ::= { upsBypass3PhaseVoltageLtoL 2 } upsBypassVoltageL3toL1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present Bypass voltage from L3 to L1." ::= { upsBypass3PhaseVoltageLtoL 3 } -- the upsConfig group --upsConfigLowRuntimeSetpoint OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION -- "This setpoint controls when the UPS will initiate a Low Runtime -- Alarm." -- ::= { upsConfig 1 } -- upsConfigDelayBeforeRestart OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION -- "The delay in seconds after utility line power returns -- before the UPS will turn on. This value is used in -- conjunction with TurnUPSOff, RebootUPS, and -- the Scheduled Shutdown objects." -- ::= { upsConfig 2 } upsConfigDelayBeforeShutdown OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The delay in seconds that the UPS waits before executing an off command upon request of an external device." ::= { upsConfig 3 } upsConfigAutoRestart OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The status of the Auto Restart mode." ::= { upsConfig 11 } upsConfigShutdownUPSAfterOSShdn OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this value to 1, enables the UPS to be shutdown after the registered clients operating systems have shutdown." ::= { upsConfig 14 } upsConfigACFailEventActions OBJECT IDENTIFIER ::= { upsConfig 12 } upsConfigDelayBeforeFirstWarningMessage OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The amount of time to delay in seconds before sending the first AC Fail message." ::= { upsConfigACFailEventActions 1 } upsConfigWarningInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The amount of time to delay in seconds between sending the additional AC Fail messages." ::= { upsConfigACFailEventActions 2 } upsConfigClientOperatingSystemShutdown OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether or not to initiate a shutdown of all registered clients based on the AC Fail event with duration." ::= { upsConfigACFailEventActions 3 } upsConfigDelayBeforeClientShutdown OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION " The time allowed in seconds during an AC Fail condition before shutting down of all registered clients." ::= { upsConfigACFailEventActions 4 } upsConfigLowBatteryEventActions OBJECT IDENTIFIER ::= { upsConfig 13 } upsConfigClientOsShutdown OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether or not to initiate a shutdown of all registered clients based on the Low Battery condition." ::= { upsConfigLowBatteryEventActions 1 } upsConfigTestScheduleTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsConfigTestScheduleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table to schedule ups battery tests." ::= { upsConfig 4 } upsConfigTestScheduleEntry OBJECT-TYPE SYNTAX UpsConfigTestScheduleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entries for each day." INDEX { upsConfigTestScheduleIndex } ::= { upsConfigTestScheduleTable 1 } UpsConfigTestScheduleEntry ::= SEQUENCE { upsConfigTestScheduleIndex INTEGER, upsConfigTestScheduleDay INTEGER, upsConfigTestScheduleTime DisplayString } upsConfigTestScheduleIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index of scheduled events." ::= { upsConfigTestScheduleEntry 1 } upsConfigTestScheduleDay OBJECT-TYPE SYNTAX INTEGER { sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7), none(8) } ACCESS read-write STATUS mandatory DESCRIPTION "The weekday on which the UPS should shut down." ::= { upsConfigTestScheduleEntry 2 } upsConfigTestScheduleTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "The time that the process of shutting down the UPS will be initiated" ::= { upsConfigTestScheduleEntry 3 } upsConfigShutdownScheduleTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsConfigShutdownScheduleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table to schedule shutting down the ups." ::= { upsConfig 5 } upsConfigShutdownScheduleEntry OBJECT-TYPE SYNTAX UpsConfigShutdownScheduleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entries for each day." INDEX { upsConfigShutdownScheduleIndex } ::= { upsConfigShutdownScheduleTable 1 } UpsConfigShutdownScheduleEntry ::= SEQUENCE { upsConfigShutdownScheduleIndex INTEGER, upsConfigScheduleShutdownDay INTEGER, upsConfigScheduleShutdownTime DisplayString, upsConfigScheduleRestartDay INTEGER, upsConfigScheduleRestartTime DisplayString } upsConfigShutdownScheduleIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index of scheduled events." ::= { upsConfigShutdownScheduleEntry 1 } upsConfigScheduleShutdownDay OBJECT-TYPE SYNTAX INTEGER { sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7), none(8) } ACCESS read-write STATUS mandatory DESCRIPTION "The weekday on which the UPS should shut down." ::= { upsConfigShutdownScheduleEntry 2 } upsConfigScheduleShutdownTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "The time that the process of shutting down the UPS will be initiated" ::= { upsConfigShutdownScheduleEntry 3 } upsConfigScheduleRestartDay OBJECT-TYPE SYNTAX INTEGER { sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7), none(8) } ACCESS read-write STATUS mandatory DESCRIPTION "The weekday on which the UPS should restart" ::= { upsConfigShutdownScheduleEntry 4 } upsConfigScheduleRestartTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "The time the UPS will restart in hh:mm:ss format." ::= { upsConfigShutdownScheduleEntry 5 } upsConfigbestLink OBJECT IDENTIFIER ::= { upsConfig 8 } bestLinkHistoryLogFrequency OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The frequency of updating the history log in minutes." ::= { upsConfigbestLink 1 } bestLinkRefreshFrequency OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The frequency of saving configuration,history and event log data in non-volatile memory. If the value is set to 0, then saving data is disabled." ::= { upsConfigbestLink 2 } bestLinkNetId OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IP address of the device. Setting this parameter causes BestLink to reboot." ::= { upsConfigbestLink 3 } bestLinkGateway OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The gateway address for the network BestLink is connected to." ::= { upsConfigbestLink 4 } bestLinkNetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The net mask of the device." ::= { upsConfigbestLink 5 } bestLinkSysDate OBJECT-TYPE SYNTAX DisplayString (SIZE(6..10)) ACCESS read-write STATUS mandatory DESCRIPTION "The system date of the device. The date is in mm/dd/yyyy format. The range of system date is from 1/1/1980 to 12/31/2037." ::= { upsConfigbestLink 6 } bestLinkSysTime OBJECT-TYPE SYNTAX DisplayString (SIZE(5..8)) ACCESS read-write STATUS mandatory DESCRIPTION "The system time of the device. The time is in hh:mm:ss format." ::= { upsConfigbestLink 7 } bestLinkTftpFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..59)) ACCESS read-write STATUS mandatory DESCRIPTION "The tftp file name that contains the software upgrade image." ::= { upsConfigbestLink 8 } bestLinkTftpHost OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The tftp host IP address from where to get the image." ::= { upsConfigbestLink 9 } bestLinkFlashEEPROM OBJECT-TYPE SYNTAX INTEGER { no(1), yes(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Saves the history log, eventlog, and configuration data to non-volatile memory." ::= { upsConfigbestLink 10 } bestLinkPrimaryTimeServer OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The primary time server is responsible for sending the correct time to the UPS." ::= { upsConfigbestLink 11 } bestLinkSecondaryTimeServer OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The secondary time server responsible for sending the correct time to the UPS." ::= { upsConfigbestLink 12 } bestLinkSoftwareVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The version of BestLink software." ::= { upsConfigbestLink 13 } bestLinkMIBVersion OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The version of MIB implemented in SNMP/WEB Card software." ::= { upsConfigbestLink 14 } bestLinkDHCPControl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable DHCP function of SNMP/WEB Card." ::= { upsConfigbestLink 15 } bestLinkTelnetControl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable Telnet function of SNMP/WEB Card." ::= { upsConfigbestLink 16 } bestLinkTftpControl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable TFTP function of SNMP/WEB Card." ::= { upsConfigbestLink 17 } bestLinkResetToDefault OBJECT-TYPE SYNTAX INTEGER { reset(1), nothing(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Reset all parameters of SNMP/WEB Card to default setting." ::= { upsConfigbestLink 18 } bestLinkRestartAgent OBJECT-TYPE SYNTAX INTEGER { restart(1), nothing(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Restart of SNMP/WEB Card." ::= { upsConfigbestLink 19 } upsConfigTrapsReceivers OBJECT IDENTIFIER ::= { upsConfig 9 } upsConfigTrapsReceiversTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsConfigTrapsReceiversEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of managers to send traps to." ::= { upsConfigTrapsReceivers 1 } upsConfigTrapsReceiversEntry OBJECT-TYPE SYNTAX UpsConfigTrapsReceiversEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The managers to send traps to." INDEX { trapsIndex} ::= { upsConfigTrapsReceiversTable 1 } UpsConfigTrapsReceiversEntry ::= SEQUENCE { trapsIndex INTEGER, trapsReceiverAddr IpAddress, receiverCommunityString DisplayString, severityLevel INTEGER, receiverAccept INTEGER } trapsIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index to a trap receiver entry." ::= { upsConfigTrapsReceiversEntry 1 } trapsReceiverAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IP address of the manager to send a trap to." ::= { upsConfigTrapsReceiversEntry 2 } receiverCommunityString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..19)) ACCESS read-write STATUS mandatory DESCRIPTION "The community name to use in the trap when sent to the manager." ::= { upsConfigTrapsReceiversEntry 3 } severityLevel OBJECT-TYPE SYNTAX INTEGER { information(1), warning(2), severe(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The severity threshold of traps to send to the manager. Traps are labeled by severity as informational(1), warning(2), severe(3). Only traps of equal or greater severity than this value are sent to the manager." ::= { upsConfigTrapsReceiversEntry 4 } receiverAccept OBJECT-TYPE SYNTAX INTEGER { yes (1), no (2) } ACCESS read-write STATUS mandatory DESCRIPTION "An entry will become active if yes, otherwise it will be disabled." ::= { upsConfigTrapsReceiversEntry 5 } upsConfigRegisteredShutdownClients OBJECT IDENTIFIER ::= { upsConfig 10 } upsRegisteredShutdownClientsTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsRegisteredShutdownClientsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of registered shutdown client table entries. The table contains zero, one, or many rows at any moment, depending upon the number of Netwatch clients registered with BestLink" ::= { upsConfigRegisteredShutdownClients 1 } upsRegisteredShutdownClientsEntry OBJECT-TYPE SYNTAX UpsRegisteredShutdownClientsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing information applicable to a particular registered shutdown client." INDEX { upsRegisteredShutdownClientsIndex } ::= { upsRegisteredShutdownClientsTable 1 } UpsRegisteredShutdownClientsEntry ::= SEQUENCE { upsRegisteredShutdownClientsIndex PositiveInteger, upsRegisteredShutdownClientsIPAddress IpAddress } upsRegisteredShutdownClientsIndex OBJECT-TYPE SYNTAX PositiveInteger ACCESS read-only STATUS mandatory DESCRIPTION "An index of alarm entries in the RegisteredShutdownClientsTable." ::= { upsRegisteredShutdownClientsEntry 1 } upsRegisteredShutdownClientsIPAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP Address of the registered shutdown client" ::= { upsRegisteredShutdownClientsEntry 2 } upsRegisteredShutdownClientsTotalNumberOf OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total number of registered shutdown clients." ::= { upsConfigRegisteredShutdownClients 2 } -- the upsControl group upsControlTurnOffUPS OBJECT-TYPE SYNTAX INTEGER { cancelUpsOff(1), upsOff(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this variable to UpsOff(2) causes the UPS to shut off. When the UPS is in the off state, the UPS will remain off until the ON/OFF switch is manually toggled. Setting this variable to cancelUpsOff(1) allows for a method to cancel the upsOff(2) command to the UPS that is still pending, or will make an attempt to restart a UPS that has been shutdown, provided that BestLink is powered by some other means. Setting this variable to rebootUps(3) causes the UPS to shut off and turn back on. Setting this variable to cancelrebootUps(4) allows for a method to cancel the rebootUps(3) command to the UPS that is still pending, or will make an attempt to restart a UPS that has been shutdown, provided that BestLink is powered by some other means." ::= { upsControl 1 } --upsControlModeOfOperation OBJECT-TYPE -- SYNTAX INTEGER { -- off(1), -- auto(2), -- lineCondition(3), -- inverter(4), -- bypass(5) -- } -- ACCESS read-write -- STATUS mandatory -- DESCRIPTION -- "Setting this variable forces the UPS into a new operating mode." -- ::= { upsControl 2 } upsControlActivateUpsScheduling OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this variable to On(2) causes the UPS to activate the scheduling parameters that have been previously configured within the upsConfigDailyShutdownScheduleTable and the upsConfigWeeklyShutdownScheduleTable. Setting this variable to Off(1) suspends all currently configured schedules." ::= { upsControl 4 } upsControlEnableGeneratorSensitivity OBJECT-TYPE SYNTAX INTEGER { auto(1), g1(2), g2(3), g3(4), g4(5), disable(6) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this value to a value other than (disable) begins to increase the UPS ability to reject poor line sources for example from a poorly regulated AC generator. The greater the value the greater the tolerance to allow poor line to be used to power the UPS. This control is used to prevent the UPS from using its batteries to create output power and allow an AC generator to supply power to the UPS." ::= { upsControl 5 } -- the upsTest group upsManualTests OBJECT-TYPE SYNTAX INTEGER { noTestInitiated(1), initiateBatteryTest(5), abortBatteryTest(9) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this variable to any value other than (1) causes the UPS to perform a manual test or abort a particular test in progress." ::= { upsTest 1 } -- the upsAlarm group upsAlarmsPresent OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The present number of active alarm conditions." ::= { upsAlarm 1 } upsLastKnownAlarm OBJECT-TYPE SYNTAX INTEGER { onBattery(1), lowRuntime(2), nearLowBattery(3), lowBattery(4), highBattery(5), checkBattery(6), replaceBattery(7), checkInverter(8), batteriesDisconnected(9), outputOverload(10), lowAcOut(11), circuitBreakerWarning(12), circuitBreakerShdn(13), bypassOn(14), autoBypass(15), siteWiringFault(16), checkFan(17), highAmbTemp(18), highHSTemp(19), highXFMRTemp(20), highPFMTemp(21), probeMissing(22), checkPowerSupply(23), tapRegulator(24), relayFailure(25), checkFuse(26), checkMOV(27), memoryError(28), callService(29), upsFailed(30), userTest(31), testInProgress(32), diagnosticTestFailed(33), ePO(34), upsOff(35), communicationsLost(36), noAlarm(37) } ACCESS read-only STATUS mandatory DESCRIPTION "A unique identifier for an alarm condition. This value must remain constant. Value 'noAlarm(37)' will be returned if no Alarm has occured till the point of GET operation." ::= { upsAlarm 2 } upsAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF UpsAlarmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmIndex equal to 1, and increments the value of upsAlarmIndex each time a new row is created." ::= { upsAlarm 3 } upsAlarmEntry OBJECT-TYPE SYNTAX UpsAlarmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing information applicable to a particular alarm." INDEX { upsAlarmIndex } ::= { upsAlarmTable 1 } UpsAlarmEntry ::= SEQUENCE { upsAlarmIndex PositiveInteger, upsAlarmName INTEGER, upsAlarmTime DisplayString } upsAlarmIndex OBJECT-TYPE SYNTAX PositiveInteger ACCESS read-only STATUS mandatory DESCRIPTION "An index of alarm entries in the alarm log." ::= { upsAlarmEntry 1 } upsAlarmName OBJECT-TYPE SYNTAX INTEGER { onBattery(1), lowRuntime(2), nearLowBattery(3), lowBattery(4), highBattery(5), checkBattery(6), replaceBattery(7), checkInverter(8), batteriesDisconnected(9), outputOverload(10), lowAcOut(11), circuitBreakerWarning(12), circuitBreakerShdn(13), bypassOn(14), autoBypass(15), siteWiringFault(16), checkFan(17), highAmbTemp(18), highHSTemp(19), highXFMRTemp(20), highPFMTemp(21), probeMissing(22), checkPowerSupply(23), tapRegulator(24), relayFailure(25), checkFuse(26), checkMOV(27), memoryError(28), callService(29), upsFailed(30), userTest(31), testInProgress(32), diagnosticTestFailed(33), ePO(34), upsOff(35), communicationsLost(36) } ACCESS read-only STATUS mandatory DESCRIPTION "A unique identifier for an alarm condition. This value must remain constant." ::= { upsAlarmEntry 2 } upsAlarmTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The time that the alarm occurred in hh:mm:ss format." ::= { upsAlarmEntry 3 } upsWellKnownAlarms OBJECT IDENTIFIER ::= { upsAlarm 4 } upsAlarmOnBattery OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS is drawing power from the batteries." ::= { upsWellKnownAlarms 1 } upsAlarmLowRuntime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The remaining battery runtime is less than or equal to the upsConfigLowRuntimeSetpoint." ::= { upsWellKnownAlarms 2 } upsAlarmNearLowBattery OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The battery voltage on the UPS has reached a value where the inverter will not be able to function very much longer." ::= { upsWellKnownAlarms 3 } upsAlarmLowBattery OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The battery voltage on the UPS has reached a value where the inverter has stopped providing output power to the connected load equipment. The UPS has shutdown to protect the batteries from complete discharge." ::= {upsWellKnownAlarms 4 } upsAlarmHighBattery OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The battery charger voltage on the UPS has reached a value that is too high for safe battery maintenance." ::= { upsWellKnownAlarms 5 } upsAlarmCheckBattery OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The periodic battery test has failed. A manual test of the batteries needs to be performed to determine which battery\batteries need replaced." ::= { upsWellKnownAlarms 6 } -- All FERRUPS models upsAlarmReplaceBattery OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "One or more batteries have been determined to require replacement. Compatibility: Fortress II" ::= { upsWellKnownAlarms 7 } upsAlarmCheckInverter OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The inverter has failed the automatic system test." ::= { upsWellKnownAlarms 8 } upsAlarmBatteriesDisconnected OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS has detected that the DC voltage needed to start up is too low or missing." ::= { upsWellKnownAlarms 9 } upsAlarmOutputOverload OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The output load exceeds the UPS output capacity." ::= { upsWellKnownAlarms 10 } upsAlarmLowAcOut OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The output load has exceeded the UPS output capacity, and the UPS has shut down." ::= { upsWellKnownAlarms 11 } upsAlarmCircuitBreakerWarning OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "To much load equipment has been connected to the UPS and has has caused excess current draw from the output." -- Unity/1 single phase UPS only ::= { upsWellKnownAlarms 12 } upsAlarmCircuitBreakerShdn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS has shut down due to an extended excess of current draw from the output." -- Unity/1 single phase UPS only ::= { upsWellKnownAlarms 13 } upsAlarmBypassOn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Bypass is presently engaged on the UPS." -- SOLA/BEST UPS only ::= { upsWellKnownAlarms 14 } upsAlarmAutoBypass OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS has gone into the Auto Bypass mode to redirect power around the UPS circuitry." -- Unity/1 single phase UPS only ::= { upsWellKnownAlarms 15 } upsAlarmSiteWiringFault OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS has found a problem in your wall outlet." ::= { upsWellKnownAlarms 16 } upsAlarmCheckFan OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The fan on the UPS has stopped " --Unity/1 single phase, Fortress, Fortress II (Fan Malfunction), --and FERRUPS (Check Cooling) ::= { upsWellKnownAlarms 17 } upsAlarmHighAmbTemp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The internal temperature inside the UPS is too hot." -- All FERRUPS models ::= { upsWellKnownAlarms 18 } upsAlarmHighHSTemp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Inverter heatsink assembly inside the UPS is to hot ." -- All FERRUPS models ::= { upsWellKnownAlarms 19 } upsAlarmHighXFMRTemp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The temperature of the main transformer inside the UPS is too hot ." -- All FERRUPS models ::= { upsWellKnownAlarms 20 } upsAlarmHighPFMTemp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The temperature of the PFM module inside the UPS is too hot ." -- FERRUPS FE with PFM module installed ::= { upsWellKnownAlarms 21 } upsAlarmProbeMissing OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "One or all of the sense probes has been disconnected on the UPS." ::= { upsWellKnownAlarms 22 } upsAlarmCheckPowerSupply OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The internal DC supply voltages are attenuated or missing." ::= { upsWellKnownAlarms 23 } upsAlarmTapRegulator OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS detected a possible failure in the tap changer (open or welded relay, etc.)" ::= { upsWellKnownAlarms 24 } upsAlarmRelayFailure OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "There is a hardware problem inside the UPS." ::= { upsWellKnownAlarms 25 } upsAlarmCheckFuse OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The failure of one or more fuses has been detected." ::= { upsWellKnownAlarms 26 } upsAlarmCheckMOV OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "One or more MOVs have failed due to a voltage surge." ::= { upsWellKnownAlarms 27 } upsAlarmMemoryError OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The UPS has lost the programmed settings in the memory of the logic board." ::= { upsWellKnownAlarms 28 } upsAlarmCallService OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A hardware malfunction has occurred inside the UPS. Please consult a factory authorized service representative for assistance." ::= { upsWellKnownAlarms 29 } upsAlarmupsFailed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A general fault in the UPS has been detected." -- BEST/SOLA UPS ::= { upsWellKnownAlarms 30 } upsAlarmUserTest OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A user test of the alarm beeper is in progress." -- All FERRUPS models ::= { upsWellKnownAlarms 31 } upsAlarmTestInProgress OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A test is in progress." ::= { upsWellKnownAlarms 32 } upsAlarmDiagnosticTestFailed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The result of the last diagnostic test indicates a failure." ::= { upsWellKnownAlarms 33 } upsAlarmEPO OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Emergency Power OFF feature has been activiated at the RS-232 port on the UPS." ::= { upsWellKnownAlarms 34 } upsAlarmUpsOff OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The output of the UPS is in the off state." ::= { upsWellKnownAlarms 35 } upsAlarmCommunicationsLost OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A problem has been encountered in the communications between the agent and the UPS." ::= { upsWellKnownAlarms 36 } -- Traps upsTrapPowerFail TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "WARNING: Utility power not available." ::= 1 upsTrapPowerRestored TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: Utility power has been restored." ::= 2 upsTrapUPSOnBattery TRAP-TYPE ENTERPRISE bestLink VARIABLES { upsBatteryTimeOnBattery, upsBatteryRuntimeRemaining, upsBatteryVoltage } DESCRIPTION "WARNING: The UPS has switched to battery backup power." ::= 3 upsTrapUPSNotOnBattery TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS is not on battery power." ::= 4 upsTrapLowRuntime TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The runtime remaining on battery power is very short, and the UPS will soon shut down." ::= 5 upsTrapUPSCanRunOnBattery TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from a low runtime condition." ::= 6 upsTrapNearLowBattery TRAP-TYPE ENTERPRISE bestLink VARIABLES {upsBatteryVoltage } DESCRIPTION "SEVERE: The UPS batteries are low and will soon be exhausted. If utility power is not restored the UPS will put itself to 'sleep' and immediately cut power to the load." ::= 7 upsTrapHighBattery TRAP-TYPE ENTERPRISE bestLink VARIABLES {upsBatteryVoltage } DESCRIPTION "WARNING: The battery charger voltage on the UPS has reached a value that is too high for safe battery maintenance." -- Fortress, Fortress II, Unity/1 Single-Phase, and FERRUPS. -- Also include (Check Charger) -- for FERRUPS FE series. ::= 8 upsTrapBatteryOK TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from a near low or high battery condition." ::= 9 upsTrapLowBattery TRAP-TYPE ENTERPRISE bestLink VARIABLES { upsBatteryVoltage } DESCRIPTION "SEVERE: The UPS will run for approximately 2 minutes more and then put itself to sleep to prevent a complete discharge of the batteries." ::= 10 upsTrapCheckBattery TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The UPS has failed a scheduled or manual battery test." ::= 11 upsTrapReplaceBattery TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: One or more UPS batteries need to be replaced." ::= 12 upsTrapCheckInverter TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The UPS has failed a scheduled or manual inverter test." ::= 13 upsTrapBatteriesDisconnected TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "WARNING: The UPS battery voltage is either too low or missing to start up." ::= 14 upsTrapOutputOverload TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "WARNING: The output load exceeds the UPS output capacity." ::= 15 upsTrapUPSNoLongerOverloaded TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from an output overload condition." ::= 16 upsTrapLowAcOut TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The output load has exceeded the UPS output capacity, and the UPS has shut down." -- All FERRUPS Models ::= 17 upsTrapCircuitBreakerWarning TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: To much load equipment has been connected to the UPS and has has caused excess current draw from the output." -- Unity/1 single phase UPS only ::= 18 upsTrapCircuitBreakerOK TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from a circuit breaker warning condition." ::= 19 upsTrapCircuitBreakerShdn TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The UPS has shut down due to an extended excess of current draw from the output." -- Unity/1 single phase UPS only ::= 20 upsTrapBypassOn TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The Bypass is presently engaged on the UPS." ::= 21 upsTrapUPSOnline TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from an on bypass condition." ::= 22 upsTrapSiteWiringFault TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The UPS has found a problem in your wall outlet." ::= 23 upsTrapCheckFan TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The fan on the UPS has stopped ." -- Unity/1 single phase, Fortress, Fortress II (Fan Malfunction) -- and FERRUPS (Check Cooling) ::= 24 upsTrapHighUPSTemp TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The internal temperature inside the UPS is too hot." -- All FERRUPS models ::= 25 upsTrapTempOK TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from a high ambient temp condition." ::= 26 upsTrapHighHSTemp TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The Inverter heatsink assembly inside the UPS is too hot ." -- All FERRUPS models ::= 27 upsTrapHSTempOK TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from a high heatsink temp condition." ::= 28 upsTrapHighXFMRTemp TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The temperature of the main transformer inside the UPS is too hot ." -- All FERRUPS models ::= 29 upsTrapHighPFMTemp TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The temperature of the PFM module inside the UPS is too hot." -- FERRUPS FE with PFM module installed ::= 30 upsTrapProbeMissing TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: One or all of the temperature probes has been disconnected on the UPS." -- FERRUPS FE only ::= 31 upsTrapProbeReconnected TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has returned from a probe missing condition." ::= 32 upsTrapCheckPowerSupply TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The internal DC supply voltages are attenuated or missing." ::= 33 upsTrapTapRegulatorFault TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The UPS detected a possible failure in the tap changer (open or welded relay, etc.)" ::= 34 upsTrapRelayFailure TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: There is a hardware problem inside the UPS." ::= 35 upsTrapCheckFuse TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The failure of one or more fuses has been detected." ::= 36 upsTrapCheckMOV TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: One or more MOVs have failed due to a voltage surge." ::= 37 upsTrapMemoryError TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The UPS has lost the programmed settings in the memory of the logic board." ::= 38 upsTrapCallService TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: A hardware malfunction has occurred inside the UPS. Please consult a factory authorized service representative for assistance." ::= 39 upsTrapManualAlarmBeeperTestInitiated TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: A manual test of the alarm beeper is being performed on the UPS." ::= 40 upsTrapManualAlarmBeeperTestAborted TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The test of UPS has completed." ::= 41 upsTrapScheduledTestInProgress TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: A test is in progress." ::= 42 upsTrapScheduledTestFailed TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The last test performed failed." ::= 43 upsTrapCommunicationLost TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: Communication to the UPS has been lost. Steps to reestablish communication are in progress." ::= 44 upsTrapCommunicationRestored TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: Communication with the UPS has been restored." ::= 45 upsTrapUPSGoingDown TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "WARNING: The ups has been given shutdown command by the management station." ::= 46 upsTrapUPSTurnedOff TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The ups has been turned off by the management station." ::= 47 upsTrapUPSSleeping TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS has entered in 'sleep' mode. Power to the load has been cut off." ::= 48 upsTrapUPSWokeUp TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS woke up from 'sleep' mode. Power to the load has been restored." ::= 49 upsTrapUPSRebooted TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "INFORMATION: The UPS is rebooted." ::= 50 upsTrapEmergencyPowerOFF TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: The Emergency Power OFF feature has been activiated at the RS-232 port on the UPS." ::= 51 upsTrapHistLogWarn TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "WARNING: The ups history log buffer is almost full." ::= 52 upsTrapEventLogWarn TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "WARNING: The ups event log buffer is almost full." ::= 53 upsTrapUPSFail TRAP-TYPE ENTERPRISE bestLink DESCRIPTION "SEVERE: A critical fault has been detected inside the UPS. Power to the load has been shut off." ::= 54 END