--Delta-MIB { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) delta(2254) ups(2) upsv5(5) } DeltaUPSv5-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises, IpAddress, TimeTicks FROM RFC1155-SMI DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215; delta OBJECT IDENTIFIER ::= { enterprises 2254 } ups OBJECT IDENTIFIER ::= { delta 2 } upsv5 OBJECT IDENTIFIER ::= { ups 5 } dupsIdent OBJECT IDENTIFIER ::= { upsv5 1 } dupsControl OBJECT IDENTIFIER ::= { upsv5 2 } dupsConfig OBJECT IDENTIFIER ::= { upsv5 3 } dupsInput OBJECT IDENTIFIER ::= { upsv5 4 } dupsOutput OBJECT IDENTIFIER ::= { upsv5 5 } dupsBypass OBJECT IDENTIFIER ::= { upsv5 6 } dupsBattery OBJECT IDENTIFIER ::= { upsv5 7 } dupsTest OBJECT IDENTIFIER ::= { upsv5 8 } dupsAlarm OBJECT IDENTIFIER ::= { upsv5 9 } dupsPowerModule OBJECT IDENTIFIER ::= { upsv5 10 } dupsTrapArgs OBJECT IDENTIFIER ::= { upsv5 11 } dupsParallel OBJECT IDENTIFIER ::= { upsv5 12 } dupsIntegrated OBJECT IDENTIFIER ::= { upsv5 13 } dupsTraps OBJECT IDENTIFIER ::= { upsv5 20 } -- -- dups Ident group -- dupsIdentManufacturer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) ACCESS read-only STATUS mandatory DESCRIPTION "The name of the UPS manufacturer." ::= { dupsIdent 1 } dupsIdentModel OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) ACCESS read-only STATUS mandatory DESCRIPTION "The UPS Model designation." ::= { dupsIdent 2 } dupsIdentUPSSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "The UPS firmware/software version(s). This variable may or may not has the same value as upsIdentAgentSoftwareVersion in some implementations." ::= { dupsIdent 3 } dupsIdentAgentSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) ACCESS read-only STATUS mandatory DESCRIPTION "The UPS agent software version. This variable may or may not has the same value as upsIdentUPSSoftwareVersion in some implementations." ::= { dupsIdent 4 } dupsIdentName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-write STATUS mandatory DESCRIPTION "A string identifying the UPS. This object should be set by the administrator." ::= { dupsIdent 5 } dupsAttachedDevices OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) ACCESS read-write STATUS mandatory DESCRIPTION "A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator." ::= { dupsIdent 6 } dupsRatingOutputVA OBJECT-TYPE SYNTAX INTEGER UNITS "VA" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the nominal output VA rating. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 7 } dupsRatingOutputVoltage OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the nominal output voltage rating. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 8 } dupsRatingOutputFrequency OBJECT-TYPE SYNTAX INTEGER UNITS "Hz" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the nominal output frequency rating. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 9 } dupsRatingInputVoltage OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the nominal input voltage rating. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 10 } dupsRatingInputFrequency OBJECT-TYPE SYNTAX INTEGER UNITS "Hz" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the nominal input frequency rating. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 11 } dupsRatingBatteryVoltage OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the nominal battery voltage rating. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 12 } dupsLowTransferVoltUpBound OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The minimum input line voltage upper bound allowed before the UPS system transfers to battery backup. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 13 } dupsLowTransferVoltLowBound OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The minimum input line voltage lower bound allowed before the UPS system transfers to battery backup. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 14 } dupsHighTransferVoltUpBound OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The maximum input line voltage upper bound allowed before the UPS system transfers to battery backup. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 15 } dupsHighTransferVoltLowBound OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The maximum input line voltage lower bound allowed before the UPS system transfers to battery backup. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 16 } dupsLowBattTime OBJECT-TYPE SYNTAX INTEGER UNITS "Second" ACCESS read-only STATUS mandatory DESCRIPTION "Minutes, time from low battery to low battery shutdown. The value -1 indicates this UPS does not support this item." ::= { dupsIdent 17 } dupsOutletRelays OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of outlet relay. If it is 0, the function is not available for the UPS." ::= { dupsIdent 18 } dupsType OBJECT-TYPE SYNTAX INTEGER { on-line(1), off-line(2), line-interactive(3), three-phase(4), splite-phase(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicate the UPS type." ::= { dupsIdent 19 } -- -- dups Control group -- dupsShutdownType OBJECT-TYPE SYNTAX INTEGER { output(1), system(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off." ::= { dupsControl 1 } dupsAutoReboot OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "In backup mode, the UPS may shutdown normally by SDA command, dry-contact remote shutdown signal or low battery shutdown. This command is used to determine the unit should restart or not next time when the power restores" ::= { dupsControl 2 } dupsShutdownAction OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "If the value is greater than 0 the UPS performs shutdown action that defined by ShutdownType after the seconds. 0, aborted." ::= { dupsControl 3 } dupsRestartAction OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "UPS will restart after the indicated number of minutes. -1, aborted." ::= { dupsControl 4 } dupsSetOutletRelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Indicate which outlet relay, from 1,2,3... ." ::= { dupsControl 5 } dupsRelayOffDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Turn the relay off after the seconds. The relay was indicated by SetOutletRelay." ::= { dupsControl 6 } dupsRelayOnDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Turn the relay on after the minutes. The relay was indicated by SetOutletRelay." ::= { dupsControl 7 } dupsSmartShutdown OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Any value to initiate the Smart Shutdown for the UPS." ::= { dupsControl 8 } dupsClearEnergy OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Any value to clear the energy record in the UPS." ::= { dupsControl 9 } -- -- dups Configure group -- dupsConfigBuzzerAlarm OBJECT-TYPE SYNTAX INTEGER { alarm(1), silence(2) } ACCESS read-write STATUS mandatory DESCRIPTION "UPS will keep silence but will alarm again when next power event is occurred" ::= { dupsConfig 1 } dupsConfigBuzzerState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If it is disabled then the UPS is always muted." ::= { dupsConfig 2 } dupsConfigSensitivity OBJECT-TYPE SYNTAX INTEGER { normal(1), reduced(2), low(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The seneitivity of the UPS to utility line abnormalities or noises." ::= { dupsConfig 3 } dupsConfigLowVoltageTransferPoint OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-write STATUS mandatory DESCRIPTION "The minimum input line voltage allowed before the UPS system transfers to battery backup." ::= { dupsConfig 4 } dupsConfigHighVoltageTransferPoint OBJECT-TYPE SYNTAX INTEGER UNITS "Volt" ACCESS read-write STATUS mandatory DESCRIPTION "The maximum line voltage allowed before the UPS system transfers to battery backup." ::= { dupsConfig 5 } dupsConfigUPSBootDelay OBJECT-TYPE SYNTAX INTEGER UNITS "Second" ACCESS read-write STATUS mandatory DESCRIPTION "Delay the UPS startup after power restores. The power quality may not stable when power restores, this feature let the UPS wait a period of time to startup the system." ::= { dupsConfig 6 } dupsConfigExternalBatteryPack OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Indicate the number of external battery pack." ::= { dupsConfig 7 } dupsConfigSmartShutdownOSDelay OBJECT-TYPE SYNTAX INTEGER UNITS "Second" ACCESS read-write STATUS mandatory DESCRIPTION "The estimated operating system shutdown delay time for Smart Shutdown." ::= { dupsConfig 8 } dupsConfigSmartShutdownUPSDelay OBJECT-TYPE SYNTAX INTEGER UNITS "Second" ACCESS read-write STATUS mandatory DESCRIPTION "The estimated UPS shutdown delay time for Smart Shutdown." ::= { dupsConfig 9 } dupsConfigEconomicMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable or disable the economic mode." ::= { dupsConfig 10 } -- -- dups Input group -- dupsInputNumLines OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of input lines utilized in this device." ::= { dupsInput 1 } dupsInputFrequency1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Hertz" ACCESS read-only STATUS mandatory DESCRIPTION "The current input line 1 frequency to the UPS system in 1/10 Hz. The value -1 indicates this UPS does not support this item." ::= { dupsInput 2 } dupsInputVoltage1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input phase 1 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsInput 3 } dupsInputVoltage12 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 1-2 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsInput 4 } dupsInputCurrent1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 1 current to the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsInput 5 } dupsInputPower1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 1 power to the UPS system in 1 Watt. The value -1 indicates this UPS does not support this item." ::= { dupsInput 6 } dupsInputFrequency2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Hertz" ACCESS read-only STATUS mandatory DESCRIPTION "The current input line 2 frequency to the UPS system in 1/10 Hz. The value -1 indicates this UPS does not support this item." ::= { dupsInput 7 } dupsInputVoltage2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input phase 2 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsInput 8 } dupsInputVoltage23 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 2-3 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsInput 9 } dupsInputCurrent2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 2 current to the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsInput 10 } dupsInputPower2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 2 power to the UPS system in 1 Watt. The value -1 indicates this UPS does not support this item." ::= { dupsInput 11 } dupsInputFrequency3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Hertz" ACCESS read-only STATUS mandatory DESCRIPTION "The current input line 3 frequency to the UPS system in 1/10 Hz. The value -1 indicates this UPS does not support this item." ::= { dupsInput 12 } dupsInputVoltage3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input phase 3 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsInput 13 } dupsInputVoltage31 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 3-1 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsInput 14 } dupsInputCurrent3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 3 current to the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsInput 15 } dupsInputPower3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 3 power to the UPS system in 1 Watt. The value -1 indicates this UPS does not support this item." ::= { dupsInput 16 } dupsInputEnergy1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 1 energy to the UPS system in 1 kWh. The value -1 indicates this UPS does not support this item." ::= { dupsInput 17 } dupsInputEnergy2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 2 energy to the UPS system in 1 kWh. The value -1 indicates this UPS does not support this item." ::= { dupsInput 18 } dupsInputEnergy3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The Input line 3 energy to the UPS system in 1 kWh. The value -1 indicates this UPS does not support this item." ::= { dupsInput 19 } dupsInputEnergyTotal OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The total Input energy to the UPS system in 1 kWh. The value -1 indicates this UPS does not support this item." ::= { dupsInput 20 } dupsInputLineFailCause OBJECT-TYPE SYNTAX INTEGER { no(1), outoftolvolt(2), outoftolfreq(3), utilityoff(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Cause of input outage." ::= { dupsInput 21 } dupsInputBadStatus OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Incorrect input voltage or frequency." ::= { dupsInput 22 } -- -- dups Output group -- dupsOutputSource OBJECT-TYPE SYNTAX INTEGER { normal(1), battery(2), bypass(3), reducing(4), boosting(5), manualBypass(6), other(7), noOutput(8), onEco(9) } ACCESS read-only STATUS mandatory DESCRIPTION "The present source of output power. The enumeration noOutput(8) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker." ::= { dupsOutput 1 } dupsOutputFrequency OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Hertz" ACCESS read-only STATUS mandatory DESCRIPTION "The present output frequency in 1/10 Hz. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 2 } dupsOutputNumLines OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of output lines utilized in this device." ::= { dupsOutput 3 } dupsOutputVoltage1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output phase 1 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 4 } dupsOutputVoltage12 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 1-2 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 5 } dupsOutputCurrent1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 1 current of the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 6 } dupsOutputPower1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 1 active power of the UPS system in watts. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 7 } dupsOutputLoad1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Percent" ACCESS read-only STATUS mandatory DESCRIPTION "The current UPS output line 1 load expressed in percent of rated capacity. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 8 } dupsOutputVoltage2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output phase 2 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 9 } dupsOutputVoltage23 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 2-3 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 10 } dupsOutputCurrent2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 2 current of the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 11 } dupsOutputPower2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 2 active power of the UPS system in watts. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 12 } dupsOutputLoad2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Percent" ACCESS read-only STATUS mandatory DESCRIPTION "The current UPS output line 2 load expressed in percent of rated capacity. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 13 } dupsOutputVoltage3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output phase 3 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 14 } dupsOutputVoltage31 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 3-1 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 15 } dupsOutputCurrent3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 3 current of the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 16 } dupsOutputPower3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The Output line 3 active power of the UPS system in watts. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 17 } dupsOutputLoad3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Percent" ACCESS read-only STATUS mandatory DESCRIPTION "The current UPS output line 3 load expressed in percent of rated capacity. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 18 } dupsOutputTotalActivePower OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 kW" ACCESS read-only STATUS mandatory DESCRIPTION "The total output active power of the UPS system in 0.1 kW. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 19 } dupsOutputTotalApparentPower OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 kVA" ACCESS read-only STATUS mandatory DESCRIPTION "The total output apparent power of the UPS system in 0.1 kVA. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 20 } dupsOutputTotalPowerFactor OBJECT-TYPE SYNTAX INTEGER UNITS "1 Percent" ACCESS read-only STATUS mandatory DESCRIPTION "The total output power factor of the UPS system. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 21 } dupsOutputEnergy1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The UPS output line 1 energy in kWh. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 22 } dupsOutputEnergy2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The UPS output line 2 energy in kWh. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 23 } dupsOutputEnergy3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The UPS output line 3 energy in kWh. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 24 } dupsOutputEnergyTotal OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The UPS total output energy in kWh. The value -1 indicates this UPS does not support this item." ::= { dupsOutput 25 } -- -- dups Bypass group -- dupsBypassFrequency OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Hertz" ACCESS read-only STATUS mandatory DESCRIPTION "The present bypass frequency in 1/10 Hz. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 1 } dupsBypassNumLines OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of bypass lines utilized in this device." ::= { dupsBypass 2 } dupsBypassVoltage1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass phase 1 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 3 } dupsBypassVoltage12 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 1-2 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 4 } dupsBypassCurrent1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 1 current of the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 5 } dupsBypassPower1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 1 real power of the UPS system in watts. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 6 } dupsBypassVoltage2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass phase 2 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 7 } dupsBypassVoltage23 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 2-3 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 8 } dupsBypassCurrent2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 2 current of the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 9 } dupsBypassPower2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 2 real power of the UPS system in watts. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 10 } dupsBypassVoltage3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass phase 3 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 11 } dupsBypassVoltage31 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 3-1 voltage of the UPS system in 1/10 V. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 12 } dupsBypassCurrent3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 3 current of the UPS system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 13 } dupsBypassPower3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The bypass line 3 real power of the UPS system in watts. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 14 } dupsBypassSTSTemperature OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The measurement of bypass STS temperature. The value -1 indicates this UPS does not support this item." ::= { dupsBypass 15 } -- -- dups Battery group -- dupsBatteryCondition OBJECT-TYPE SYNTAX INTEGER { good(1), weak(2), replace(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The indication of the capacity remaining in the UPS system's batteries when AC normal." ::= { dupsBattery 1 } dupsBatteryStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), low(2), depleted(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The indication of the capacity remaining in the UPS system's batteries when AC failed. A value of ok indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of low indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of depleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output)." ::= { dupsBattery 2 } dupsBatteryCharge OBJECT-TYPE SYNTAX INTEGER { floating(1), charging(2), resting(3), discharging(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Representing the battery charge status." ::= { dupsBattery 3 } dupsSecondsOnBattery OBJECT-TYPE SYNTAX INTEGER UNITS "1 Second" ACCESS read-only STATUS mandatory DESCRIPTION "If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power." ::= { dupsBattery 4 } dupsBatteryEstimatedTime OBJECT-TYPE SYNTAX INTEGER UNITS "1 Minute" ACCESS read-only STATUS mandatory DESCRIPTION "Estimated time from backup to low battery shutdown." ::= { dupsBattery 5 } dupsBatteryPosVoltage OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt DC" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present positive battery voltage in 1/10 V." ::= { dupsBattery 6 } dupsBatteryNegVoltage OBJECT-TYPE SYNTAX INTEGER UNITS "-0.1 Volt DC" ACCESS read-only STATUS mandatory DESCRIPTION "The magnitude of the present negative battery voltage in -1/10 V." ::= { dupsBattery 7 } dupsBatteryPosCurrent OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp DC" ACCESS read-only STATUS mandatory DESCRIPTION "The present positive battery current in 1/10 A." ::= { dupsBattery 8 } dupsBatteryNegCurrent OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp DC" ACCESS read-only STATUS mandatory DESCRIPTION "The present negative battery current in 1/10 A." ::= { dupsBattery 9 } dupsBatteryPosCapacity OBJECT-TYPE SYNTAX INTEGER (0..100) UNITS "1 Percent" ACCESS read-only STATUS mandatory DESCRIPTION "An estimate of the positive battery charge remaining expressed as a percent of full charge." ::= { dupsBattery 10 } dupsBatteryNegCapacity OBJECT-TYPE SYNTAX INTEGER (0..100) UNITS "1 Percent" ACCESS read-only STATUS mandatory DESCRIPTION "An estimate of the negative battery charge remaining expressed as a percent of full charge." ::= { dupsBattery 11 } dupsTemperature OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degrees Centigrade" ACCESS read-only STATUS mandatory DESCRIPTION "The measurement of internal temperature in the UPS." ::= { dupsBattery 12 } dupsLastReplaceDate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The last battery replacement date. The format is YYYYMMDD." ::= { dupsBattery 13 } dupsNextReplaceDate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The next battery replacement date. The format is YYYYMMDD." ::= { dupsBattery 14 } dupsBatteryBreaker OBJECT-TYPE SYNTAX INTEGER { open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicate the battery breaker status." ::= { dupsBattery 15 } dupsBatteryCab1Tempurature OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degrees Centigrade" ACCESS read-only STATUS mandatory DESCRIPTION "Temperature of battery cabnet 1." ::= { dupsBattery 16 } dupsBatteryCab2Tempurature OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degrees Centigrade" ACCESS read-only STATUS mandatory DESCRIPTION "Temperature of battery cabnet 2." ::= { dupsBattery 17 } dupsBatteryCab3Tempurature OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degrees Centigrade" ACCESS read-only STATUS mandatory DESCRIPTION "Temperature of battery cabnet 3." ::= { dupsBattery 18 } dupsBatteryCab4Tempurature OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degrees Centigrade" ACCESS read-only STATUS mandatory DESCRIPTION "Temperature of battery cabnet 4." ::= { dupsBattery 19 } -- -- dups Test group -- dupsTestType OBJECT-TYPE SYNTAX INTEGER { abort(1), generalTest(2), batteryTest(3), testFor10sec(4), testUntilBattlow(5) } ACCESS read-write STATUS mandatory DESCRIPTION "Perform the UPS Test procedure." ::= { dupsTest 1 } dupsTestResultsSummary OBJECT-TYPE SYNTAX INTEGER { noTestsInitiated(1), donePass(2), inProgress(3), generalTestFail(4), batteryTestFail(5), deepBatteryTestFail(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The results of the current or last UPS diagnostics test performed. The values for donePass(1), generalTestFail(3), and batteryTestFail(4) indicate that the test completed either successfully, with a warning, or with an error, respectively.Tests which have not yet concluded are indicated by inProgress(2). The value noTestsInitiated(1) indicates that no previous test results are available." ::= { dupsTest 2 } dupsTestResultsDetail OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned." ::= { dupsTest 3 } dupsGeneratorTest OBJECT-TYPE SYNTAX INTEGER { abort(1), start(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Perform the Generator Test procedure." ::= { dupsTest 4 } dupsGeneratorTestStatus OBJECT-TYPE SYNTAX INTEGER { inProgress(1), none(2), inhibitTest(3), abnormallyTerminate(4), byInstruction(5), byTimeout(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The results of the current or last generator diagnostics test performed.The values for None(2), InhibitTest(3), AbnormallyTerminate(4), ByInstruction(5), and ByTimeout(6) indicate that the tye of termination test. Tests which have not yet concluded are indicated by inProgress(1)" ::= { dupsTest 5 } -- -- dups Alarm group -- dupsAlarmDisconnect OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicate the communication of the UPS is connected or disconnect?" ::= { dupsAlarm 1 } dupsAlarmInputOutOfRange OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Representing the input power is out of tolerance. This item is used to indicate the input power fail, a test condition should not set this item on." ::= { dupsAlarm 2 } dupsAlarmBatteryLow OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Are the UPS batteries low?" ::= { dupsAlarm 3 } dupsAlarmLoadOnBypass OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Does the UPS load on bypass?" ::= { dupsAlarm 4 } dupsAlarmOther OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicate there is an alarm detected but which is not defined here." ::= { dupsAlarm 5 } dupsAlarmBatteryGroundFault OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the battery ground fault has been detected." ::= { dupsAlarm 6 } dupsAlarmTestInProgress OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Does the UPS test in progress?" ::= { dupsAlarm 7 } dupsAlarmBatteryTestFail OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Does the UPS test fail?" ::= { dupsAlarm 8 } dupsAlarmFuseFailure OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The failure of one or more fuses has been detected." ::= { dupsAlarm 9 } dupsAlarmOutputOverload OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The output load exceeds the UPS output capacity." ::= { dupsAlarm 10 } dupsAlarmInverterAbnormal OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Representing the inverter fail alarm." ::= { dupsAlarm 11 } dupsAlarmLoadOnReserve OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Does the UPS load on reserve?" ::= { dupsAlarm 12 } dupsAlarmTemperature OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Representing one of the temperature sensors has been determined its value is out of the limits." ::= { dupsAlarm 13 } dupsAlarmBypassOutOfRange OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The bypass power is out of range." ::= { dupsAlarm 14 } dupsAlarmStandby OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The UPS system is in the standby state." ::= { dupsAlarm 15 } dupsAlarmChargerFail OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "An incorrected problem has been detected within the UPS charger subsystem" ::= { dupsAlarm 16 } dupsAlarmFanFail OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The failure of one or more fans in the UPS has been detected." ::= { dupsAlarm 17 } dupsAlarmEconomicMode OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The UPS is working in the economic mode (act like an off-line UPS)." ::= { dupsAlarm 18 } dupsAlarmOutputOff OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "UPS output is turned off." ::= { dupsAlarm 19 } dupsAlarmSmartShutdown OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the Smart Shutdown is in progress." ::= { dupsAlarm 20 } dupsAlarmEmergencyPowerOff OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Representing the UPS is shutdown due to the Emergency Power Off button is pressed." ::= { dupsAlarm 21 } dupsAlarmUPSShutdown OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The UPS has been shutdown including remote and fault shutdown." ::= { dupsAlarm 22 } dupsAlarmEPO OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Representing the UPS is shutdown due to the Emergency Power Off button is pressed." ::= { dupsAlarm 23 } dupsAlarmOutVoltOverLimit OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the output voltage is over limit." ::= { dupsAlarm 24 } dupsAlarmOutVoltUnderLimit OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the output voltage is under limit." ::= { dupsAlarm 25 } dupsAlarmPowerModule OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate there is at least one alarm from power module." ::= { dupsAlarm 26 } dupsAlarmOutputBreaker OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the output breaker is detected open or close." ::= { dupsAlarm 27 } dupsAlarmOutletBank1Breaker OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the outlet bank-1 breaker is detected open or close." ::= { dupsAlarm 28 } dupsAlarmOutletBank2Breaker OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the outlet bank-2 breaker is detected open or close." ::= { dupsAlarm 29 } dupsAlarmOutletBank3Breaker OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the outlet bank-3 breaker is detected open or close." ::= { dupsAlarm 30 } dupsAlarmOutletBank4Breaker OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the outlet bank-4 breaker is detected open or close." ::= { dupsAlarm 31 } dupsAlarmSummary OBJECT-TYPE SYNTAX INTEGER{ none(1), informational(2), warning(3), alarm(4) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the alarm level for the UPS." ::= { dupsAlarm 32 } dupsAlarmRedundancyLoss OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the capacity of redundancy lost in a modular UPS." ::= { dupsAlarm 33 } dupsAlarmPhaseAsynchronous OBJECT-TYPE SYNTAX INTEGER{ asynchronous(1), synchronous(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the Phase is detected asynchronous or synchronous." ::= { dupsAlarm 34 } dupsAlarmRectifierAbnormal OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the Rectifier is detected alarm or normal." ::= { dupsAlarm 35 } dupsAlarmBypassBreakerOpen OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the bypass breaker is detected open or close." ::= { dupsAlarm 36 } dupsAlarmMainInputBreakerOpen OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the main input breaker is detected open or close." ::= { dupsAlarm 37 } dupsAlarmManualBypassBreaker OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "To indicate the manual bypass breaker is detected open or close." ::= { dupsAlarm 38 } -- -- dups Power Module group -- dupsPMBypassInputAlarm OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the bypass voltage/frequency is abnormal." ::= { dupsPowerModule 1 } dupsPMBypassPhaseAlarm OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the bypass phase sequence is abnormal." ::= { dupsPowerModule 2 } dupsPMBypassSTSOverloadAlarm OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the bypass STS overload." ::= { dupsPowerModule 3 } dupsPMBypassSTSOverTempAlarm OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the bypass STS over temperature." ::= { dupsPowerModule 4 } dupsPMBypassSTSFailAlarm OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the bypass STS fail." ::= { dupsPowerModule 5 } dupsPMTable OBJECT-TYPE SYNTAX SEQUENCE OF DupsPMEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of power module table entries." ::= { dupsPowerModule 6 } dupsPMEntry OBJECT-TYPE SYNTAX DupsPMEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing information applicable to a particular power module." INDEX { dupsPMID } ::= { dupsPMTable 1 } DupsPMEntry ::= SEQUENCE { dupsPMID INTEGER, dupsPMPFCTemp INTEGER, dupsPMINVTemp INTEGER, dupsPMINVTempR INTEGER, dupsPMINVTempS INTEGER, dupsPMINVTempT INTEGER, dupsPMINVVolt1 INTEGER, dupsPMINVVolt2 INTEGER, dupsPMINVVolt3 INTEGER, dupsPMStsNotExist INTEGER, dupsPMStsOff INTEGER, dupsPMStsRepair INTEGER, dupsPMStsFaultShutdown INTEGER, dupsPMStsPFCFuseFail INTEGER, dupsPMStsPFCOverTempWarning INTEGER, dupsPMStsPFCOverTempShutdown INTEGER, dupsPMStsPFCOverVoltWarning INTEGER, dupsPMStsPFCOverVoltShutdown INTEGER, dupsPMStsPFCUnderVoltWarning INTEGER, dupsPMStsPFCUnderVoltShutdown INTEGER, dupsPMStsPFCGeneralFault INTEGER, dupsPMStsPFCFanFail INTEGER, dupsPMStsPFCCurrentLimit INTEGER, dupsPMStsPFCOff INTEGER, dupsPMStsPFCInnerCommFail INTEGER, dupsPMStsPFCNotCalibrated INTEGER, dupsPMStsINVFuseFail INTEGER, dupsPMStsINVOverTempWarning INTEGER, dupsPMStsINVOverTempShutdown INTEGER, dupsPMStsINVFanFail INTEGER, dupsPMStsINVShortCircuit INTEGER, dupsPMStsINVSTSFail INTEGER, dupsPMStsINVCircuitFail INTEGER, dupsPMStsINVOverVolt INTEGER, dupsPMStsINVOverload INTEGER, dupsPMStsINVInnerCommFail INTEGER, dupsPMStsINVEPO INTEGER, dupsPMStsINVParallelCommFail INTEGER, dupsPMStsINVParallelFail INTEGER, dupsPMStsINVSTSOn INTEGER, dupsPMStsINVNotCalibrated INTEGER, dupsPMStsChargerFail INTEGER, dupsPMSummaryStatus INTEGER, dupsPMPFCTempR INTEGER, dupsPMPFCTempS INTEGER, dupsPMPFCTempT INTEGER } dupsPMID OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The power module identifier." ::= { dupsPMEntry 1 } dupsPMPFCTemp OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module PFC temperature." ::= { dupsPMEntry 2 } dupsPMINVTemp OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module inverter temperature." ::= { dupsPMEntry 3 } dupsPMINVTempR OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module inverter-R temperature." ::= { dupsPMEntry 4 } dupsPMINVTempS OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module inverter-S temperature." ::= { dupsPMEntry 5 } dupsPMINVTempT OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module inverter-T temperature." ::= { dupsPMEntry 6 } dupsPMINVVolt1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The inverter line 1 voltage of the power module in 1/10 V." ::= { dupsPMEntry 7 } dupsPMINVVolt2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The inverter line 2 voltage of the power module in 1/10 V." ::= { dupsPMEntry 8 } dupsPMINVVolt3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Volt" ACCESS read-only STATUS mandatory DESCRIPTION "The inverter line 3 voltage of the power module in 1/10 V." ::= { dupsPMEntry 9 } dupsPMStsNotExist OBJECT-TYPE SYNTAX INTEGER{ notExist(1), existed(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module is existed or not?" ::= { dupsPMEntry 10 } dupsPMStsOff OBJECT-TYPE SYNTAX INTEGER{ pmOff(1), pmOn(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module is on or off?" ::= { dupsPMEntry 11 } dupsPMStsRepair OBJECT-TYPE SYNTAX INTEGER{ repair(1), notRepair(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module is in repair mode or not?" ::= { dupsPMEntry 12 } dupsPMStsFaultShutdown OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module status of fault shutdown." ::= { dupsPMEntry 13 } dupsPMStsPFCFuseFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC fuse open or close?" ::= { dupsPMEntry 14 } dupsPMStsPFCOverTempWarning OBJECT-TYPE SYNTAX INTEGER{ warning(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC over temperature warning." ::= { dupsPMEntry 15 } dupsPMStsPFCOverTempShutdown OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC over temperature shutdown." ::= { dupsPMEntry 16 } dupsPMStsPFCOverVoltWarning OBJECT-TYPE SYNTAX INTEGER{ warning(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC over voltage warning." ::= { dupsPMEntry 17 } dupsPMStsPFCOverVoltShutdown OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC over voltage shutdown." ::= { dupsPMEntry 18 } dupsPMStsPFCUnderVoltWarning OBJECT-TYPE SYNTAX INTEGER{ warning(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC under voltage warning." ::= { dupsPMEntry 19 } dupsPMStsPFCUnderVoltShutdown OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC under voltage shutdown." ::= { dupsPMEntry 20 } dupsPMStsPFCGeneralFault OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC genreal fault." ::= { dupsPMEntry 21 } dupsPMStsPFCFanFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC fan fail." ::= { dupsPMEntry 22 } dupsPMStsPFCCurrentLimit OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC output current limit." ::= { dupsPMEntry 23 } dupsPMStsPFCOff OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC off." ::= { dupsPMEntry 24 } dupsPMStsPFCInnerCommFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC inner communication fail." ::= { dupsPMEntry 25 } dupsPMStsPFCNotCalibrated OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module PFC is not calibrated." ::= { dupsPMEntry 26 } dupsPMStsINVFuseFail OBJECT-TYPE SYNTAX INTEGER{ open(1), close(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter fuse open or close?" ::= { dupsPMEntry 27 } dupsPMStsINVOverTempWarning OBJECT-TYPE SYNTAX INTEGER{ warning(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter over temperature warning." ::= { dupsPMEntry 28 } dupsPMStsINVOverTempShutdown OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter over temperature shutdown." ::= { dupsPMEntry 29 } dupsPMStsINVFanFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter fan fail." ::= { dupsPMEntry 30 } dupsPMStsINVShortCircuit OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter short circuit." ::= { dupsPMEntry 31 } dupsPMStsINVSTSFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter STS fail." ::= { dupsPMEntry 32 } dupsPMStsINVCircuitFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter circuit fail shutdown." ::= { dupsPMEntry 33 } dupsPMStsINVOverVolt OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter over voltage shutdown." ::= { dupsPMEntry 34 } dupsPMStsINVOverload OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter overload." ::= { dupsPMEntry 35 } dupsPMStsINVInnerCommFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter inner communication fail." ::= { dupsPMEntry 36 } dupsPMStsINVEPO OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter EPO shutdown." ::= { dupsPMEntry 37 } dupsPMStsINVParallelCommFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter parallel communication fail." ::= { dupsPMEntry 38 } dupsPMStsINVParallelFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter parallel fail." ::= { dupsPMEntry 39 } dupsPMStsINVSTSOn OBJECT-TYPE SYNTAX INTEGER{ on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the status of power module Inverter state." ::= { dupsPMEntry 40 } dupsPMStsINVNotCalibrated OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Inverter is not calibrated." ::= { dupsPMEntry 41 } dupsPMStsChargerFail OBJECT-TYPE SYNTAX INTEGER{ alarm(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the power module Charger fail." ::= { dupsPMEntry 42 } dupsPMSummaryStatus OBJECT-TYPE SYNTAX INTEGER{ abnormal(1), normal(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The power module summary status." ::= { dupsPMEntry 43 } dupsPMPFCTempR OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module pfc-R temperature." ::= { dupsPMEntry 44 } dupsPMPFCTempS OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module pfc-S temperature." ::= { dupsPMEntry 45 } dupsPMPFCTempT OBJECT-TYPE SYNTAX INTEGER UNITS "1 Degree Celsius" ACCESS read-only STATUS mandatory DESCRIPTION "The power module pfc-T temperature." ::= { dupsPMEntry 46 } -- -- dups Trap Args -- dupsDescription OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This OID is used for traps to send with a string argument. A get of this OID will return an empty string." ::= { dupsTrapArgs 1 } dupsTimeTicks OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This OID is used for traps to send with a TimeTicks argument. A get of this OID will return 0." ::= { dupsTrapArgs 2 } -- -- dups Parallel group -- dupsParallelRatingVA OBJECT-TYPE SYNTAX INTEGER UNITS "1 VA" ACCESS read-only STATUS mandatory DESCRIPTION "The summary rating VA to the parallel UPSs system." ::= { dupsParallel 1 } dupsParallelRatingPower OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The summary rating power to the parallel UPSs system." ::= { dupsParallel 2 } dupsParallelInCurrent1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The summary input line 1 current to the parallel UPSs system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 3 } dupsParallelInCurrent2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The summary input line 2 current to the parallel UPSs system in 1/!0 A. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 4 } dupsParallelInCurrent3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The summary input line 3 current to the parallel UPSs system in 1/!0 A. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 5 } dupsParallelOutCurrent1 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 1 current to the parallel UPSs system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 6 } dupsParallelOutCurrent2 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 2 current to the parallel UPSs system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 7 } dupsParallelOutCurrent3 OBJECT-TYPE SYNTAX INTEGER UNITS "0.1 Amp" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 3 current to the parallel UPSs system in 1/10 A. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 8 } dupsParallelOutPower1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 1 power to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 9 } dupsParallelOutPower2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 2 power to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 10 } dupsParallelOutPower3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 Watt" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 3 power to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 11 } dupsParallelInEnergy1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary input line 1 energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 12 } dupsParallelInEnergy2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary input line 2 energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 13 } dupsParallelInEnergy3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary input line 3 energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 14 } dupsParallelInEnergyTotal OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary total input energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 15 } dupsParallelOutEnergy1 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 1 energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 16 } dupsParallelOutEnergy2 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 2 energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 17 } dupsParallelOutEnergy3 OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary output line 3 energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 18 } dupsParallelOutEnergyTotal OBJECT-TYPE SYNTAX INTEGER UNITS "1 kWh" ACCESS read-only STATUS mandatory DESCRIPTION "The summary total output energy to the parallel UPSs system. The value -1 indicates this UPS does not support this item." ::= { dupsParallel 19 } -- -- dups Integrated group -- dupsIntegratedParallel OBJECT-TYPE SYNTAX INTEGER{ parallel(1), noParallel(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Multiple frame with the same group present." ::= { dupsIntegrated 1 } dupsIntegratedDryInput1 OBJECT-TYPE SYNTAX INTEGER{ active(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Dry1 Input state." ::= { dupsIntegrated 2 } dupsIntegratedDryInput2 OBJECT-TYPE SYNTAX INTEGER{ active(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Dry2 Input state." ::= { dupsIntegrated 3 } dupsIntegratedDryInput3 OBJECT-TYPE SYNTAX INTEGER{ active(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Dry3 Input state." ::= { dupsIntegrated 4 } dupsIntegratedDryInput4 OBJECT-TYPE SYNTAX INTEGER{ active(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Dry4 Input state." ::= { dupsIntegrated 5 } -- -- dups Trap group -- dupsCommunicationLost TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: Communication with the UPS failed." ::= 1 dupsCommunicationEstablished TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: Communication with the UPS reestablished." ::= 2 dupsPowerFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "WARNING: Power failed! The UPS is operating on battery power." ::= 3 dupsPowerRestored TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: Power restored! The utility power restored." ::= 4 dupsLowBattery TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS batteries are low and will soon be exhausted." ::= 5 dupsReturnFromLowBattery TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS has returned from a low battery condition." ::= 6 dupsLoadOnBypass TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS loads on bypass." ::= 7 dupsNoLongerLoadOnBypass TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS is not on bypass mode." ::= 8 dupsUPSFault TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: A general fault caused in the UPS." ::= 9 dupsReturnFromUPSFault TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS is returned from general fault." ::= 10 dupsBatteryGroundFault TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS battery ground fault." ::= 11 dupsNoLongerBatteryFault TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS recovered from battery ground fault." ::= 12 dupsTestInProgress TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS test in progress." ::= 13 dupsBatteryTestFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS test fail." ::= 14 dupsFuseFailure TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS fuse failed." ::= 15 dupsFuseRecovered TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS fuse recovered." ::= 16 dupsOutputOverload TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS overload!." ::= 17 dupsNoLongerOverload TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: Recovered from UPS overload." ::= 18 dupsInverterAbnormal TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS inverter abnormal." ::= 19 dupsInverterRecovered TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: Recovered from UPS inverter abnormal." ::= 20 dupsSmartShutdownInit TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: Smart Shutdown is initiated." ::= 21 dupsCancelShutdown TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: Cancel UPS Shutdown." ::= 22 dupsTestCompleted TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: This trap is sent upon completion of a UPS diagnostic test." ::= 23 dupsEPOON TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: This trap is sent when emergency power off is on." ::= 24 dupsEPOOFF TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: This trap is sent when UPS recover from emergency power off." ::= 25 dupsTemperatureAlarm TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: This trap is sent when the UPS temperature out of range." ::= 26 dupsTemperatureNormal TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: This trap is sent when UPS temperature back to normal." ::= 27 dupsBattReplace TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "WARNING: The battery needs to be replaced." ::= 28 dupsReturnFromBattReplace TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS recovered from battery replacement." ::= 29 dupsOutputOff TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: Indicate the UPS output is turned off." ::= 30 dupsReturnFromOutputOff TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS recovered from output off." ::= 31 dupsShutdown TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS has been shutdown including remote and fault shutdown." ::= 32 dupsReturnFromShutdown TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS recovered from shutdown." ::= 33 dupsChargerFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: An incorrected problem has been detected within the UPS charger subsystem." ::= 34 dupsReturnFromChargerFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS recovered from charger fail." ::= 35 dupsOnStandby TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS system is in the standby state." ::= 36 dupsReturnFromStandby TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS no longer on standby mode." ::= 37 dupsFanFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The failure of one or more fans in the UPS has been detected." ::= 38 dupsReturnFromFanFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS recover from fan fail." ::= 39 dupsOnEconomic TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS is working in the economic mode (act like an off-line UPS)." ::= 40 dupsReturnFromEconomic TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS no longer on economic mode." ::= 41 dupsPowerModuleFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: One of the power modules is detected failed." ::= 42 dupsReturnFromPowerModuleFail TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The power module is back to normal." ::= 43 dupsOutputBreakerOff TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The output breaker is detected off." ::= 44 dupsReturnFromOutputBreakerOff TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The output breaker is back to on." ::= 45 dupsBatteryDepleted TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS batteries are depleted and will soon be exhausted." ::= 46 dupsReturnFromBatteryDepleted TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS has returned from a battery depleted condition." ::= 47 dupsLoadOnManualBypass TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The UPS loads on manual bypass." ::= 48 dupsNoLongerLoadOnManualBypass TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The UPS is not on manual bypass mode." ::= 49 dupsBatteryBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The battery breaker is detected open." ::= 50 dupsReturnFromBatteryBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The battery breaker is returned from open." ::= 51 dupsOutletBankOn TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The outlet bank was turned on." ::= 52 dupsOutletBankOff TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The outlet bank was turned off." ::= 53 dupsRedundancyLoss TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "WARNING: The redundancy capacity lost in a modular UPS." ::= 54 dupsReturnFromRedundancyLoss TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The redundancy capacity recoverd in a modular UPS." ::= 55 dupsPhaseAsynchronous TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The phase is detected asynchronous." ::= 56 dupsReturnFromPhaseAsynchronous TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The phase is returned from asynchronous." ::= 57 dupsRectifierAbnormal TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The rectifier is detected abnormal." ::= 58 dupsReturnFromRectifierAbnormal TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The rectifier is returned from abnormal." ::= 59 dupsBypassBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The bypass breaker is detected open." ::= 60 dupsReturnFromBypassBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The bypass breaker is returned from open." ::= 61 dupsMainInputBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The main inputs breaker is detected open." ::= 62 dupsReturnFromMainInputBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The main input breaker is returned from open." ::= 63 dupsManualBypassBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "SEVER: The manual bypass breaker is detected open." ::= 64 dupsReturnFromManualBypassBreakerOpen TRAP-TYPE ENTERPRISE dupsTraps VARIABLES { dupsTimeTicks, dupsDescription } DESCRIPTION "INFORMATION: The manual bypass breaker is returned from open." ::= 65 END