------------------------------------------------------------------------------ -- File Name : ZTE-AN-LDP-MIB.mib -- Date : 2008-06-30 -- Author : ZTE Nms dept. -- -- Zte LDP Mib for Access Node -- -- ------------------------------------------------------------------------------ ZTE-AN-LDP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, experimental, Integer32, Unsigned32, Counter64, TimeTicks, IpAddress FROM SNMPv2-SMI zxAnL3IfIndex FROM ZTE-AN-L3-IF-MIB RowStatus, DisplayString FROM SNMPv2-TC zxAn FROM ZTE-AN-TC-MIB InetAddress, InetAddressType FROM INET-ADDRESS-MIB; zxAnLdpMib MODULE-IDENTITY LAST-UPDATED "200806301500Z" ORGANIZATION "ZTE Corporation." CONTACT-INFO "ZTE NMS dept. Ma Jian 68897122" DESCRIPTION "This MIB contains managed object definitions for LDP operation." ::= { zxAn 55 } zxAnLdpGlobalObjects OBJECT IDENTIFIER ::= {zxAnLdpMib 1} zxAnLdpObjects OBJECT IDENTIFIER ::= {zxAnLdpMib 2} ------------------------------------------------------------------------------ -- Following objects are defined. -- 1.zxAn LDP global mgmt objects -- 2.zxAn LDP target session table -- 3.zxAn LDP session table -- 4.zxAn LDP L3 Interface Entity table ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ -- 1.zxAnLDP global mgmt objects ------------------------------------------------------------------------------ zxAnLdpMplsEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable MPLS service." DEFVAL { disable } ::= { zxAnLdpGlobalObjects 1 } zxAnLdpMplsMinLabel OBJECT-TYPE SYNTAX Integer32 (16..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum value in dynamic label range of MPLS. For OLT C300, the label value range from 16 to 1044478." DEFVAL { 16 } ::= { zxAnLdpGlobalObjects 2 } zxAnLdpMplsMaxLabel OBJECT-TYPE SYNTAX Integer32 (16..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum value in dynamic label range of MPLS. For OLT C300, the label value range from 16 to 1044478, and the default maximum value is 1044478." DEFVAL { 100000 } ::= { zxAnLdpGlobalObjects 3 } zxAnLdpMplsLdpRouterId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "A zxAnL3IfIndex is used as the LDP router ID. It is recommended to use loopback interface as LDP router ID. L3 VLAN interface also can be configed. IP address of zxAnL3IfIndex should be configured before the zxAnL3IfIndex configured as the router ID." DEFVAL { 0 } ::= { zxAnLdpGlobalObjects 4 } zxAnLdpMplsLdpRouterIdForce OBJECT-TYPE SYNTAX INTEGER { force(1), noForce(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "zxAnLdpMplsLdpRouterId is valid immediately. When force is set whether the router ID designated takes effect depends on the current status of the designated interface. When current status of designated interface is up, and other addresses are not the current router ID. Router will force router ID to change into designated value, intermit current session, free label studied in the session and intermit the MPLS transmission relating to binding with labels. When current status of the designated interface is down, once it turns to up. Router will force router ID to change into designated value, intermit current session, free label studied in the session and intermit MPLS transmission relating to binding with labels." DEFVAL { noForce } ::= { zxAnLdpGlobalObjects 5 } zxAnLdpMplsExplicitNullEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "MPLS explicit null label enable switch." DEFVAL { disable } ::= { zxAnLdpGlobalObjects 6 } zxAnLdpMplsMinInUseLabel OBJECT-TYPE SYNTAX INTEGER(16..1048575) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum value in dynamic label range of MPLS in use. For OLT C300, the label value ranges from 16 to 1044478." ::= { zxAnLdpGlobalObjects 7 } zxAnLdpMplsMaxInUseLabel OBJECT-TYPE SYNTAX INTEGER(16..1048575) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum value in dynamic label range of MPLS in use. For OLT C300, the label value ranges from 16 to 1044478." ::= { zxAnLdpGlobalObjects 8 } zxAnLdpMplsSessInitBackoffTime OBJECT-TYPE SYNTAX INTEGER(10..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The initial time which LDP entity should wait and try again after LDP failed to establish a session." DEFVAL { 15 } ::= { zxAnLdpGlobalObjects 9 } zxAnLdpMplsSessMaxBackoffTime OBJECT-TYPE SYNTAX INTEGER(10..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time which LDP entity could use to rebuild session after LDP failed to establish a session. The waiting time starts from the initial back off time, then increases exponentially up to the maximum back off time." DEFVAL { 120 } ::= { zxAnLdpGlobalObjects 10 } zxAnLdpMplsSessKeepAliveTime OBJECT-TYPE SYNTAX INTEGER(15..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The timer which is the proposed keep alive hold timer for LDP session." DEFVAL { 180 } ::= { zxAnLdpGlobalObjects 11 } zxAnLdpMplsGrEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "LDP GR(Graceful Restart) function enable switch. It indicates whether LDP GR function should be enabled." DEFVAL { disable } ::= { zxAnLdpGlobalObjects 12 } zxAnLdpMplsGrRecoveryTime OBJECT-TYPE SYNTAX INTEGER(15..600) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time which is the proposed GR recovery timer for this LDP entity. After LDP session rebuilt, GR Helper assists GR Restarter to update label forwarding table." DEFVAL { 120 } ::= { zxAnLdpGlobalObjects 13 } zxAnLdpMplsGrNeighKeepAliveTime OBJECT-TYPE SYNTAX INTEGER(5..300) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time which is the proposed keep alive neighbor when a LDP entity found the peer is down." DEFVAL { 120 } ::= { zxAnLdpGlobalObjects 14 } zxAnLdpMplsVpnGrEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "MPLS Layer 2 VPN GR function enable switch." DEFVAL { disable } ::= { zxAnLdpGlobalObjects 15 } zxAnLdpMplsHelloHoldTime OBJECT-TYPE SYNTAX INTEGER(3..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The timer which is the proposed Hello hold timer for this LDP entity. A value of 65535 means infinite." DEFVAL { 15 } ::= { zxAnLdpGlobalObjects 16 } zxAnLdpMplsHelloSendInterval OBJECT-TYPE SYNTAX INTEGER(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The time interval to send Hello message for this LDP entity. The time must be smaller than the hello hold time." DEFVAL { 5 } ::= { zxAnLdpGlobalObjects 17 } zxAnLdpMplsTgtHelloHoldTime OBJECT-TYPE SYNTAX INTEGER(3..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The timer which is the proposed targeted Hello hold timer for this LDP entity. A value of 65535 means infinite." DEFVAL { 45 } ::= { zxAnLdpGlobalObjects 18 } zxAnLdpMplsTgtHelloSendInterval OBJECT-TYPE SYNTAX INTEGER(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The time interval to send targeted Hello message for this LDP entity. The time must be smaller than the targeted hello hold time." DEFVAL { 15 } ::= { zxAnLdpGlobalObjects 19 } zxAnLdpMplsKeepSessWithHelloMsg OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "LDP session keeping alive with hello messages enable switch. If the switch is enabling, the LDP session reset keep alive timer when receiving a hello message." DEFVAL { disable } ::= { zxAnLdpGlobalObjects 20 } zxAnLdpMplsGrHelperEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Graceful restart helper enable switch." DEFVAL { enable } ::= { zxAnLdpGlobalObjects 21 } zxAnLdpMplsLabelControlMode OBJECT-TYPE SYNTAX INTEGER { ordered(1), independent(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To specify control mode of LSP." DEFVAL { independent } ::= { zxAnLdpGlobalObjects 22 } zxAnLdpMplsLabelRetentionMode OBJECT-TYPE SYNTAX INTEGER { conservative(1), liberal(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To specify retention mode of LSP." DEFVAL { liberal } ::= { zxAnLdpGlobalObjects 23 } zxAnLdpMplsPktWithLabelEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To specify label encapsulation mode when LSR sending protocol packets." DEFVAL { disable } ::= { zxAnLdpGlobalObjects 24 } ------------------------------------------------------------------------------ -- 2.zxAn LDP target session table ------------------------------------------------------------------------------ zxAnLdpTargetSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF ZxAnLdpTargetSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the MPLS target session." ::= { zxAnLdpObjects 3 } zxAnLdpTargetSessionEntry OBJECT-TYPE SYNTAX ZxAnLdpTargetSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents an LDP target session." INDEX { zxAnLdpTargetIpAddrType, zxAnLdpTargetIpAddr } ::= { zxAnLdpTargetSessionTable 1 } ZxAnLdpTargetSessionEntry ::= SEQUENCE { zxAnLdpTargetIpAddrType InetAddressType, zxAnLdpTargetIpAddr InetAddress, zxAnLdpTargetDistributionMode INTEGER, zxAnLdpTargetSessionRowStatus RowStatus } zxAnLdpTargetIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of the zxAnLdpTargetIpAddr, as defined in the InetAddress MIB." ::= { zxAnLdpTargetSessionEntry 1 } zxAnLdpTargetIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Peer address of target LDP session." ::= { zxAnLdpTargetSessionEntry 2 } zxAnLdpTargetDistributionMode OBJECT-TYPE SYNTAX INTEGER { dod(1), du(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The label distribution mode." DEFVAL { du } ::= { zxAnLdpTargetSessionEntry 3 } zxAnLdpTargetSessionRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status of the table." ::= { zxAnLdpTargetSessionEntry 20 } ------------------------------------------------------------------------------ -- 3.zxAn LDP session table ------------------------------------------------------------------------------ zxAnLdpSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF ZxAnLdpSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LDP session table. This table contains information about LDP session." ::= { zxAnLdpObjects 4 } zxAnLdpSessionEntry OBJECT-TYPE SYNTAX ZxAnLdpSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains LDP information." INDEX { zxAnLdpPeerIpAddrType, zxAnLdpPeerIpAddr } ::= { zxAnLdpSessionTable 1 } ZxAnLdpSessionEntry ::= SEQUENCE { zxAnLdpPeerIpAddrType InetAddressType, zxAnLdpPeerIpAddr InetAddress, zxAnLdpMd5Pwd DisplayString, zxAnLdpMd5PwdConfStatus INTEGER, zxAnLdpMd5PwdEncrypt INTEGER, zxAnLdpSessionReset INTEGER, zxAnLdpSessionRowStatus RowStatus } zxAnLdpPeerIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of the zxAnLdpPeerIpAddr, as defined in the InetAddress MIB." ::= { zxAnLdpSessionEntry 1 } zxAnLdpPeerIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of peer." ::= { zxAnLdpSessionEntry 2 } zxAnLdpMd5Pwd OBJECT-TYPE SYNTAX DisplayString (SIZE (3..80)) MAX-ACCESS read-create STATUS current DESCRIPTION "Password used for communication between LSRs." ::= { zxAnLdpSessionEntry 3 } zxAnLdpMd5PwdConfStatus OBJECT-TYPE SYNTAX INTEGER { noPwd(1), withPwd(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status indicates whether the MD5 is registered." ::= { zxAnLdpSessionEntry 4 } zxAnLdpMd5PwdEncrypt OBJECT-TYPE SYNTAX INTEGER { noEncrypt(1), encrypt(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The status indicates whether the MD5 password is encrypted. When the password is encrypted, the password cannot be read." ::= { zxAnLdpSessionEntry 5 } zxAnLdpSessionReset OBJECT-TYPE SYNTAX INTEGER { noReset(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used to reset the LDP session." ::= { zxAnLdpSessionEntry 6 } zxAnLdpSessionRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status of the table." ::= { zxAnLdpSessionEntry 20 } ------------------------------------------------------------------------------ -- 4.zxAn LDP L3 Interface Entity table ------------------------------------------------------------------------------ zxAnLdpL3IfEntityTable OBJECT-TYPE SYNTAX SEQUENCE OF ZxAnLdpL3IfEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the MPLS Label Distribution Protocol Entities which exist on this L3 VLAN interface." ::= { zxAnLdpObjects 5 } zxAnLdpL3IfEntityEntry OBJECT-TYPE SYNTAX ZxAnLdpL3IfEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains information of the LDP Entity." INDEX { zxAnL3IfIndex } ::= { zxAnLdpL3IfEntityTable 1 } ZxAnLdpL3IfEntityEntry ::= SEQUENCE { zxAnLdpL3IfTransAddrMode INTEGER, zxAnLdpL3IfTransAddrType InetAddressType, zxAnLdpL3IfTransAddr InetAddress, zxAnLdpL3IfDistributionMode INTEGER, zxAnLdpL3IfEntityRowStatus RowStatus } zxAnLdpL3IfTransAddrMode OBJECT-TYPE SYNTAX INTEGER { unconfigured(0), ifIp(1), specifyIp(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Change the transport address configuration of LDP." ::= { zxAnLdpL3IfEntityEntry 1 } zxAnLdpL3IfTransAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the zxAnLdpTransAddr, as defined in the InetAddress MIB." ::= { zxAnLdpL3IfEntityEntry 2 } zxAnLdpL3IfTransAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Address of transport." ::= { zxAnLdpL3IfEntityEntry 3 } zxAnLdpL3IfDistributionMode OBJECT-TYPE SYNTAX INTEGER { dod(1), du(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The label distribution mode." DEFVAL { du } ::= { zxAnLdpL3IfEntityEntry 4 } zxAnLdpL3IfEntityRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status of the Table." ::= { zxAnLdpL3IfEntityEntry 20 } END