ZTE-AN-INTERFACE-STATS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Gauge32, Counter64 FROM SNMPv2-SMI RowStatus, DisplayString, TruthValue, TEXTUAL-CONVENTION, DateAndTime FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB zxAnInterfaceMib FROM ZTE-AN-INTERFACE-MIB ZxAnIfindex FROM ZTE-AN-TC-MIB HCPerfCurrentCount FROM HC-PerfHist-TC-MIB; zxAnInterfaceStatsMib MODULE-IDENTITY LAST-UPDATED "201109132000Z" ORGANIZATION "ZTE Corporation" CONTACT-INFO "Zhang Weiping ZTE Corporation Mail: zhang.weiping@zte.com.cn Tel : 021-68896470" DESCRIPTION "The MIB module for the Performance Management of ZTE Access Node interface." REVISION "201109132000Z" DESCRIPTION "Modify this mib according to standar." REVISION "201108101500Z" DESCRIPTION "Add the table zxAnBrgIfCurrStatsTable for vport port stats function." REVISION "201108051500Z" DESCRIPTION "Add the table zxAnEthIfCurrStatsTable for ether port stats function." REVISION "201107021400Z" DESCRIPTION "Initial version of this MIB module." ::= {zxAnInterfaceMib 11} -------------------------------------------------------------------------------- -- Following objects are defined. -- 1.Ethernet port performance -- 2.Bridge port performance -- 3.Service port statistics -- Following conformance information is defined. -- 31.zxAnIfPerfConformance -------------------------------------------------------------------------------- zxAnIfPerfObjects OBJECT IDENTIFIER ::= { zxAnInterfaceStatsMib 2 } -------------------------------------------------------------------------------- -- 1.Ethernet port performance -------------------------------------------------------------------------------- zxAnEthIfCurrStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ZxAnEthIfCurrStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current performance data table of the ethernet interfaces." ::= { zxAnIfPerfObjects 2 } zxAnEthIfCurrStatsEntry OBJECT-TYPE SYNTAX ZxAnEthIfCurrStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current performance data entry of the ethernet interfaces." INDEX { ifIndex} ::= { zxAnEthIfCurrStatsTable 1 } ZxAnEthIfCurrStatsEntry ::= SEQUENCE { zxAnEthIfInOctets Counter64, zxAnEthIfInPkts Counter64, zxAnEthIfInUcastPkts Counter64, zxAnEthIfInMcastPkts Counter64, zxAnEthIfInBcastPkts Counter64, zxAnEthIfInOversizedPkts Counter64, zxAnEthIfInUndersizedPkts Counter64, zxAnEthIfOutOctets Counter64, zxAnEthIfOutPkts Counter64, zxAnEthIfOutUcastPkts Counter64, zxAnEthIfOutMcastPkts Counter64, zxAnEthIfOutBcastPkts Counter64, zxAnEthIfOutPausePkts Counter64, zxAnEthIfOutDiscardPkts Counter64, zxAnEthIfOutCollisions Counter64, zxAnEthIfSingleCollisions Counter64, zxAnEthIfMultipleCollisions Counter64, zxAnEthIfFcsErrors Counter64, zxAnEthIfAlignmentErrors Counter64, zxAnEthIfReset INTEGER } zxAnEthIfInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 1 } zxAnEthIfInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 2 } zxAnEthIfInUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 3 } zxAnEthIfInMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 4 } zxAnEthIfInBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 5 } zxAnEthIfInOversizedPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets,which above the configured MTU-size, e.g.mtu = 2000 (frames >2000 are discarded)." ::= { zxAnEthIfCurrStatsEntry 6 } zxAnEthIfInUndersizedPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets,which above the min port size, the value is 64." ::= { zxAnEthIfCurrStatsEntry 7 } zxAnEthIfOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters." ::= { zxAnEthIfCurrStatsEntry 8 } zxAnEthIfOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets transmitted out of the interface, including framing characters." ::= { zxAnEthIfCurrStatsEntry 9 } zxAnEthIfOutUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 10 } zxAnEthIfOutMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime" ::= { zxAnEthIfCurrStatsEntry 11 } zxAnEthIfOutBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 12 } zxAnEthIfOutPausePkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MAC Control frames transmitted on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCOutPauseFrames object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 13 } zxAnEthIfOutDiscardPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 14 } zxAnEthIfOutCollisions OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames that are involved in out collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 15 } zxAnEthIfSingleCollisions OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames that are involved in a single collision, and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsMultipleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 16 } zxAnEthIfMultipleCollisions OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames that are involved in more than one collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 17 } zxAnEthIfFcsErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with frame-too-long or frame-too-short error. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. Note: Coding errors detected by the physical layer for speeds above 10 Mb/s will cause the frame to fail the FCS check. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsFCSErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 18 } zxAnEthIfAlignmentErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. This counter does not increment for group encoding schemes greater than 4 bits per group. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsAlignmentErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnEthIfCurrStatsEntry 19 } zxAnEthIfReset OBJECT-TYPE SYNTAX INTEGER { perfReset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear all the current performance variables. When get this variable, always return 1." ::= { zxAnEthIfCurrStatsEntry 100 } -------------------------------------------------------------------------------- -- 2.Bridge port performance -------------------------------------------------------------------------------- zxAnBrgIfCurrStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ZxAnBrgIfCurrStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current performance data table of bridge interfaces." ::= { zxAnIfPerfObjects 3 } zxAnBrgIfCurrStatsEntry OBJECT-TYPE SYNTAX ZxAnBrgIfCurrStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current performance data entry of bridge interfaces." INDEX { ifIndex} ::= { zxAnBrgIfCurrStatsTable 1 } ZxAnBrgIfCurrStatsEntry ::= SEQUENCE { zxAnBrgIfInOctets Counter64, zxAnBrgIfInUcastPkts Counter64, zxAnBrgIfInMcastPkts Counter64, zxAnBrgIfInBcastPkts Counter64, zxAnBrgIfOutOctets Counter64, zxAnBrgIfOutUcastPkts Counter64, zxAnBrgIfOutMcastPkts Counter64, zxAnBrgIfOutBcastPkts Counter64, zxAnBrgIfReset INTEGER, zxAnBrgIfStatsRowStatus RowStatus } zxAnBrgIfInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnBrgIfCurrStatsEntry 1 } zxAnBrgIfInUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnBrgIfCurrStatsEntry 2 } zxAnBrgIfInMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnBrgIfCurrStatsEntry 3 } zxAnBrgIfInBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnBrgIfCurrStatsEntry 4 } zxAnBrgIfOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters." ::= { zxAnBrgIfCurrStatsEntry 5 } zxAnBrgIfOutUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnBrgIfCurrStatsEntry 6 } zxAnBrgIfOutMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime" ::= { zxAnBrgIfCurrStatsEntry 7 } zxAnBrgIfOutBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { zxAnBrgIfCurrStatsEntry 8 } zxAnBrgIfReset OBJECT-TYPE SYNTAX INTEGER { perfReset(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Clear all the current performance variables. When get this variable, always return 1." ::= { zxAnBrgIfCurrStatsEntry 100 } zxAnBrgIfStatsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnBrgIfCurrStatsEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1)." ::= { zxAnBrgIfCurrStatsEntry 101 } -------------------------------------------------------------------------------- -- 3.Service port statistics -------------------------------------------------------------------------------- zxAnSrvPortCurrStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ZxAnSrvPortCurrStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current statistics data table of service port." ::= { zxAnIfPerfObjects 4 } zxAnSrvPortCurrStatsEntry OBJECT-TYPE SYNTAX ZxAnSrvPortCurrStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A zxAnSrvPortCurrStatsTable entry." INDEX { zxAnBrgPortIndex, zxAnSrvPortId } ::= { zxAnSrvPortCurrStatsTable 1 } ZxAnSrvPortCurrStatsEntry ::= SEQUENCE { zxAnBrgPortIndex ZxAnIfindex, zxAnSrvPortId Integer32, zxAnSrvPortInOctets Counter64, zxAnSrvPortOutOctets Counter64, zxAnSrvPortInUcastPkts Counter64, zxAnSrvPortOutUcastPkts Counter64, zxAnSrvPortInMcastPkts Counter64, zxAnSrvPortOutMcastPkts Counter64, zxAnSrvPortInBcastPkts Counter64, zxAnSrvPortOutBcastPkts Counter64, zxAnSrvPortInOctetRate Gauge32, zxAnSrvPortOutOctetRate Gauge32, zxAnSrvPortInOctetPeakRate Gauge32, zxAnSrvPortOutOctetPeakRate Gauge32, zxAnSrvPortCurrStatsReset INTEGER, zxAnSrvPortCurrStatsRowStatus RowStatus } zxAnBrgPortIndex OBJECT-TYPE SYNTAX ZxAnIfindex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index for a bridge port." ::= { zxAnSrvPortCurrStatsEntry 1 } zxAnSrvPortId OBJECT-TYPE SYNTAX Integer32(1..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service port ID." ::= { zxAnSrvPortCurrStatsEntry 2 } zxAnSrvPortInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters." ::= { zxAnSrvPortCurrStatsEntry 3 } zxAnSrvPortOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters." ::= { zxAnSrvPortCurrStatsEntry 4 } zxAnSrvPortInUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Received unicast packets." ::= { zxAnSrvPortCurrStatsEntry 5 } zxAnSrvPortOutUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Transmitted unicast packets." ::= { zxAnSrvPortCurrStatsEntry 6 } zxAnSrvPortInMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Received multicast packets." ::= { zxAnSrvPortCurrStatsEntry 7 } zxAnSrvPortOutMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Transmitted multicast packets." ::= { zxAnSrvPortCurrStatsEntry 8 } zxAnSrvPortInBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Received broadcast packets." ::= { zxAnSrvPortCurrStatsEntry 9 } zxAnSrvPortOutBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Transmitted broadcast packets." ::= { zxAnSrvPortCurrStatsEntry 10 } zxAnSrvPortInOctetRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Received octet rate." ::= { zxAnSrvPortCurrStatsEntry 11 } zxAnSrvPortOutOctetRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Transmitted octet rate." ::= { zxAnSrvPortCurrStatsEntry 12 } zxAnSrvPortInOctetPeakRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Received octet peak rate." ::= { zxAnSrvPortCurrStatsEntry 13 } zxAnSrvPortOutOctetPeakRate OBJECT-TYPE SYNTAX Gauge32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Transmitted octet peak rate." ::= { zxAnSrvPortCurrStatsEntry 14 } zxAnSrvPortCurrStatsReset OBJECT-TYPE SYNTAX INTEGER { perfReset(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Value 1 means to clear all the current performance value." ::= { zxAnSrvPortCurrStatsEntry 100 } zxAnSrvPortCurrStatsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnSrvPortCurrStatsEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1)." ::= { zxAnSrvPortCurrStatsEntry 101 } -------------------------------------------------------------------------------- -- 31.zxAnIfPerfConformance -------------------------------------------------------------------------------- zxAnIfPerfConformance OBJECT IDENTIFIER ::= { zxAnInterfaceStatsMib 4 } zxAnIfPerfCompliances OBJECT IDENTIFIER ::= { zxAnIfPerfConformance 1 } zxAnIfPerfGroups OBJECT IDENTIFIER ::= { zxAnIfPerfConformance 2 } zxAnIfPerfCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the ZTE-AN-INTERFACE-STATS-MIB." MODULE -- this module MANDATORY-GROUPS { zxAnEthIfPerfCurrGroup, zxAnIfPerfGroups } ::= { zxAnIfPerfCompliances 1 } zxAnEthIfPerfCurrGroup OBJECT-GROUP OBJECTS { zxAnEthIfInOctets, zxAnEthIfInPkts, zxAnEthIfInUcastPkts, zxAnEthIfInMcastPkts, zxAnEthIfInBcastPkts, zxAnEthIfInOversizedPkts, zxAnEthIfInUndersizedPkts, zxAnEthIfOutOctets, zxAnEthIfOutPkts, zxAnEthIfOutUcastPkts, zxAnEthIfOutMcastPkts, zxAnEthIfOutBcastPkts, zxAnEthIfOutPausePkts, zxAnEthIfOutDiscardPkts, zxAnEthIfOutCollisions, zxAnEthIfSingleCollisions, zxAnEthIfMultipleCollisions, zxAnEthIfFcsErrors, zxAnEthIfAlignmentErrors, zxAnEthIfReset } STATUS current DESCRIPTION "A collection of objects providing current performance data of the ethernet interfaces." ::= { zxAnIfPerfGroups 1 } zxAnBrgIfPerfCurrGroup OBJECT-GROUP OBJECTS { zxAnBrgIfInOctets, zxAnBrgIfInUcastPkts, zxAnBrgIfInMcastPkts, zxAnBrgIfInBcastPkts, zxAnBrgIfOutOctets, zxAnBrgIfOutUcastPkts, zxAnBrgIfOutMcastPkts, zxAnBrgIfOutBcastPkts, zxAnBrgIfReset } STATUS current DESCRIPTION "A collection of objects providing current performance data of the bridge interfaces." ::= { zxAnIfPerfGroups 2 } zxAnSrvPortPerfCurrGroup OBJECT-GROUP OBJECTS { zxAnSrvPortInOctets, zxAnSrvPortOutOctets, zxAnSrvPortInUcastPkts, zxAnSrvPortOutUcastPkts, zxAnSrvPortInMcastPkts, zxAnSrvPortOutMcastPkts, zxAnSrvPortInBcastPkts, zxAnSrvPortOutBcastPkts, zxAnSrvPortInOctetRate, zxAnSrvPortOutOctetRate, zxAnSrvPortInOctetPeakRate, zxAnSrvPortOutOctetPeakRate, zxAnSrvPortCurrStatsReset } STATUS current DESCRIPTION "A collection of objects providing current performance data of the service port." ::= { zxAnIfPerfGroups 3 } END