-- **************************************************************************** -- Copyright (c) 2009-2018 : -- Westermo Teleindustri AB -- 640 40 Stora Sundby -- Sweden -- url: http://www.westermo.com -- -- Contact: support@westermo.se -- Description: Westermo WeOS Private MIB-file -- Defines the WeOS branch of the Westermo Private MIB tree. -- -- **************************************************************************** WESTERMO-WEOS-MIB DEFINITIONS ::= BEGIN IMPORTS RowStatus, TruthValue, DisplayString, PhysAddress, MacAddress FROM SNMPv2-TC IpAddress, Integer32, Counter64, TimeTicks, OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE FROM SNMPv2-SMI InetAddressType, InetAddress FROM INET-ADDRESS-MIB common FROM WESTERMO-OID-MIB InterfaceIndex FROM IF-MIB VlanId FROM Q-BRIDGE-MIB entPhysicalName FROM ENTITY-MIB entPhySensorValue, entPhySensorType, entPhySensorScale, entPhySensorPrecision FROM ENTITY-SENSOR-MIB; -- WeOS module weos MODULE-IDENTITY LAST-UPDATED "201810300000Z" ORGANIZATION "Westermo" CONTACT-INFO "Copyright (c) 2010-2018: Westermo Teleindustri AB 640 40 Stora Sundby Sweden url: http://www.westermo.com Contact: support@westermo.se Description: Westermo WeOS Private MIB-file" DESCRIPTION "This MIB module controls the SNMP functionality in the WeOS branch of the Westermo private MIB." REVISION "201810300000Z" DESCRIPTION "Corrected mrpRingClosed and mrpRingOpen objects." REVISION "201803120000Z" DESCRIPTION "Added configuration hash, for running and startup configuration Added support for LLDP Custom TLV. Corrected trapHostAddress value type to DisplayString." REVISION "201710030000Z" DESCRIPTION "Added support for Alarm Status (alarmStatusTable) and ping trigger notifications (pingTriggerOk, pingTriggerWarning). Added support for MRP ring notifications" REVISION "201703280000Z" DESCRIPTION "Clarified use of rowstatus in object riCoCfgRowStatus" REVISION "201701230000Z" DESCRIPTION "Added support for configuration of Ring Coupling (RiCo) and Dual-Homing. RiCo and Dual-Homing shares the same OIDs, and are distinguished by looking at the ''Ring ID'' which is always '0' for Dual-Homing entries." REVISION "201612160000Z" DESCRIPTION "Added support for status monitoring and alarm traps for Ring Coupling (RiCo) and Dual-Homing. RiCo and Dual-Homing shares the same OIDs, and are distinguished by looking at the ''Ring ID'' which is always '0' for Dual-Homing entries. The RiCo/Dual-Homing traps are sent to indicate if an Uplink comes up or goes down, and the traps are enabled via the alarm system. Added support to configure an FRNT node as FRNT bus edge, i.e, it is possible to configure FRNT port N to 'None'. Updated descripton for frntv0RingStatus." REVISION "201606140000Z" DESCRIPTION "Adding support for addressConflict and statusRelay. Adding support for TTDP etbnInhibitionEnabled. The etbnInhibitionEnabled object is only available for units with TTDP support. Corrected access mode for lffPortIfIndex, l2QosVlanId, l2QosPortIfIndex, igmpSnoopingVlanId, inet4BaseIfIndex, inet4StatIfIndex, inet4DhcpIfIndex, trapHostId from not-accessible to read-only. Corrected access mode for inetDhcpClientId to read-only. Corrected sequence syntax for frntv0PortsSwapped to TruthValue." REVISION "201512160000Z" DESCRIPTION "Added aggregated port statistics, phy.phyStats.aggrStats." REVISION "201509090000Z" DESCRIPTION "Adding support for LLDP service" REVISION "201410100000Z" DESCRIPTION "Corrected range and description for sfpDdmPortTxPower and sfpDdmPortRxPower" REVISION "201310170000Z" DESCRIPTION "Adding support for DDM traps" REVISION "201305130000Z" DESCRIPTION "Adding support for SFP DDM." REVISION "201201030000Z" DESCRIPTION "Corrected access mode for frntv0TopologyChangeCount, frntv0TopologyTimeSinceLastChange and frntv0PortsSwapped from read-create to read-only" REVISION "201105160000Z" DESCRIPTION "Changed behaviour of inet4StatAddress. When the address is set to 0.0.0.0 the interface will now be disabled instead of configured as DHCP" REVISION "201011150000Z" DESCRIPTION "Adding support for temperature traps and summary alarm traps." REVISION "201008190000Z" DESCRIPTION "Adding support for link fail forward (LFF) to enable propagation of remote link failure, when extending an Ethernet over an SHDSL link." REVISION "200911120000Z" DESCRIPTION "Possible values for frntv0Port1State and frntv0Port2State has been changed. Adding support for FRNT ring status traps (FRNT traps are added, and the frntv0InstanceId is assigned accessibility 'accessible-for-notify'. Descriptions for power and digital-in traps are modified." REVISION "200910090000Z" DESCRIPTION "Adding support for Westermo specific traps (under weos.weosTraps). Initially traps for Digital-In and Power sensors are included." REVISION "200908260000Z" DESCRIPTION "Adding support to manage the SNMP roCommunity and rwCommunity (under weos.system.services.snmp)" REVISION "200905310000Z" DESCRIPTION "Adding system branch (weos.system)." REVISION "200905180000Z" DESCRIPTION "First WeOS revision. For WeOS software version 4.0.0 and later. Please see the WeOS Release Notes for information on MIB file updates." ::= { common 1 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Node top definitions -- ------------------------------------------------------------- command OBJECT IDENTIFIER ::= { weos 1 } phy OBJECT IDENTIFIER ::= { weos 2 } link OBJECT IDENTIFIER ::= { weos 3 } net OBJECT IDENTIFIER ::= { weos 4 } system OBJECT IDENTIFIER ::= { weos 5 } notifications OBJECT IDENTIFIER ::= { weos 6 } sfp OBJECT IDENTIFIER ::= { phy 2 } phyStats OBJECT IDENTIFIER ::= { phy 3 } vlan OBJECT IDENTIFIER ::= { link 1 } l2Qos OBJECT IDENTIFIER ::= { link 2 } frnt OBJECT IDENTIFIER ::= { link 3 } igmpSnooping OBJECT IDENTIFIER ::= { link 4 } rico OBJECT IDENTIFIER ::= { link 5 } lldpCtlv OBJECT IDENTIFIER ::= { link 6 } frntv0 OBJECT IDENTIFIER ::= { frnt 1 } iface OBJECT IDENTIFIER ::= { net 1 } ttdp OBJECT IDENTIFIER ::= { net 2 } ifaceCommon OBJECT IDENTIFIER ::= { iface 1} ifaceInet4 OBJECT IDENTIFIER ::= { iface 2} -- ifaceInet6 OBJECT IDENTIFIER ::= { iface 3} addressConflict OBJECT IDENTIFIER ::= { iface 4} services OBJECT IDENTIFIER ::= { system 1 } eventSystem OBJECT IDENTIFIER ::= { system 2 } statistics OBJECT IDENTIFIER ::= { system 3 } integrity OBJECT IDENTIFIER ::= { system 4 } cpuLoadAvg OBJECT IDENTIFIER ::= { statistics 2 } snmp OBJECT IDENTIFIER ::= { services 1 } web OBJECT IDENTIFIER ::= { services 2 } ipconfig OBJECT IDENTIFIER ::= { services 3 } ssh OBJECT IDENTIFIER ::= { services 4 } lldp OBJECT IDENTIFIER ::= { services 5 } sensorNotifications OBJECT IDENTIFIER ::= { notifications 1 } frntNotifications OBJECT IDENTIFIER ::= { notifications 2 } lffNotifications OBJECT IDENTIFIER ::= { notifications 3 } genericNotifications OBJECT IDENTIFIER ::= { notifications 4 } ddmNotifications OBJECT IDENTIFIER ::= { notifications 5 } conflictNotifications OBJECT IDENTIFIER ::= { notifications 6 } otherNotifications OBJECT IDENTIFIER ::= { notifications 7 } riCoNotifications OBJECT IDENTIFIER ::= { notifications 8 } pingNotifications OBJECT IDENTIFIER ::= { notifications 9 } -- Construct to enable mapping of SNMPv2 to SNMPv1 traps sensorNotificationPrefix OBJECT IDENTIFIER ::= { sensorNotifications 0 } frntNotificationPrefix OBJECT IDENTIFIER ::= { frntNotifications 0 } lffNotificationPrefix OBJECT IDENTIFIER ::= { lffNotifications 0 } genericNotificationPrefix OBJECT IDENTIFIER ::= { genericNotifications 0 } ddmNotificationPrefix OBJECT IDENTIFIER ::= { ddmNotifications 0 } otherNotificationPrefix OBJECT IDENTIFIER ::= { otherNotifications 0 } conflictNotificationPrefix OBJECT IDENTIFIER ::= { conflictNotifications 0 } riCoNotificationPrefix OBJECT IDENTIFIER ::= { riCoNotifications 0 } pingNotificationPrefix OBJECT IDENTIFIER ::= { pingNotifications 0 } -- ------------------------------------------------------------- -- OID Definitions -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Command group -- ------------------------------------------------------------- reboot OBJECT-TYPE SYNTAX INTEGER { reboot(1) -- reboot unit (using startup configuration) } MAX-ACCESS read-write STATUS current DESCRIPTION "Writing value '1' will reboot the unit. (The unit will boot up using the startup configuration) Reading the reboot object will return '0' (zero)" ::= { command 1 } factoryReset OBJECT-TYPE SYNTAX INTEGER { restoreAndReboot(1) -- copy factory default configuration to startup configuration and reboot. } MAX-ACCESS read-write STATUS current DESCRIPTION "Writing value '1' will reset unit configuration to factory default values and reboot. Reading the factoryReset object will return '0' (zero)" ::= { command 2 } -- ------------------------------------------------------------- -- Phy Group -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Phy: lffTable -- ------------------------------------------------------------- lffTable OBJECT-TYPE SYNTAX SEQUENCE OF LffEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing Westermo Link Fail Forward (LFF) settings and status applicable ports. Westermo LFF is used to indicate the state (up/down) of a remote link. The currently supported use case is when extending an Ethernet over an SHDSL link. LFF is used to inform the local end that the Ethernet link at the remote site is up or down." ::= { phy 1 } lffEntry OBJECT-TYPE SYNTAX LffEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each local (SHDSL) port, there is a row in the lffTable containing LFF status and settings." INDEX { lffPortIfIndex } ::= { lffTable 1 } LffEntry ::= SEQUENCE { lffPortIfIndex InterfaceIndex, lffPortIfName DisplayString, lffStatus INTEGER } lffPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This index should map to the local (SHDSL) port's ifIndex in the ifTable." ::= { lffEntry 1 } lffPortIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This name should map to the local (SHDSL) port's ifName in the ifXTable." ::= { lffEntry 2 } lffStatus OBJECT-TYPE SYNTAX INTEGER { disabled(1), -- LFF disabled on the local (SHDSL) port unknown(2), -- LFF enabled, but the state of remote (Ethernet) -- is unknown. (perhaps because the intermediate -- (SHDSL) link is down). remoteDown(3), -- LFF enabled, remote port down remoteUp(4) -- LFF enabled, remote port up } MAX-ACCESS read-only STATUS current DESCRIPTION "The lffStatus shows the status of a (Ethernet) link at the remote end of a SHDSL link: - 1 (disabled): LFF is configured 'disabled' on local (SHDSL) port. - 2 (unknown): LFF enabled, but the state of remote (Ethernet) is unknown. (perhaps because the intermediate (SHDSL) link is down). - 3 (remoteDown): LFF enabled, remote (Ethernet) port down - 4 (remoteUp): LFF enabled, remote (Ethernet) port up." ::= { lffEntry 3 } -- ------------------------------------------------------------- -- Phy: SFP -- ------------------------------------------------------------- sfpDdmPortTable OBJECT-TYPE SYNTAX SEQUENCE OF SfpDdmPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing DDM diagnostics per DDM capable SFP." ::= { sfp 1 } sfpDdmPortEntry OBJECT-TYPE SYNTAX SfpDdmPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This row in the sfpDdmPortTable containing per port SFP DDM diagnostics." INDEX { sfpDdmPortIfIndex } ::= { sfpDdmPortTable 1 } SfpDdmPortEntry ::= SEQUENCE { sfpDdmPortIfIndex InterfaceIndex, sfpDdmPortIfName DisplayString, sfpDdmPortVoltage Integer32, sfpDdmPortTemperature Integer32, sfpDdmPortBiasCurrent Integer32, sfpDdmPortTxPower Integer32, sfpDdmPortRxPower Integer32 } sfpDdmPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This index maps to the port's ifIndex in the ifTable." ::= { sfpDdmPortEntry 1 } sfpDdmPortIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The system name of the port." ::= { sfpDdmPortEntry 2 } sfpDdmPortVoltage OBJECT-TYPE SYNTAX Integer32 (0..6550) MAX-ACCESS read-only STATUS current DESCRIPTION "The supply voltage of the SFP. The accuracy is better than +/-3 % and the total range of 0 - 6550 mV. The voltage is represented in mV." ::= { sfpDdmPortEntry 3 } sfpDdmPortTemperature OBJECT-TYPE SYNTAX Integer32 (-128..128) MAX-ACCESS read-only STATUS current DESCRIPTION "Temperature of the SFP. The temperature accuracy is better than 3 degrees Celsius and the total range of -128 degrees C to +128 degrees C. " ::= { sfpDdmPortEntry 4 } sfpDdmPortBiasCurrent OBJECT-TYPE SYNTAX Integer32 (0..131) MAX-ACCESS read-only STATUS current DESCRIPTION "The transmitt bias current. The accuracy is better than +/- 10 % and the total range of 0 - 131 mA. The current is represented in uA." ::= { sfpDdmPortEntry 5 } sfpDdmPortTxPower OBJECT-TYPE SYNTAX Integer32 (-4000..820) MAX-ACCESS read-only STATUS current DESCRIPTION "Transmitt power of the laser. The accuracy is better than +/-3dB and the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented in steps of 0.01 dBm" ::= { sfpDdmPortEntry 6 } sfpDdmPortRxPower OBJECT-TYPE SYNTAX Integer32 (-4000..820) MAX-ACCESS read-only STATUS current DESCRIPTION "Receiving power of the laser. The accuracy is better than +/-3dB and the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented in steps of 0.01 dBm" ::= { sfpDdmPortEntry 7 } -- ------------------------------------------------------------- -- Phy: phyStats -- ------------------------------------------------------------- summaryFCSErrors OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The summaryFCSErrors display the total of FCS errors for all ports on the unit" ::= { phyStats 1 } bwStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF BwStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing port bandwidth rates." ::= { phyStats 2 } bwStatsEntry OBJECT-TYPE SYNTAX BwStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each local port, there is a row in the bwStatsTable containing port bandwidth rates." INDEX { bwStatsIndex } ::= { bwStatsTable 1 } BwStatsEntry ::= SEQUENCE { bwStatsIndex InterfaceIndex, bwStatsEnabled TruthValue, bwStatsBitrateIn10s Counter64, bwStatsBitrateOut10s Counter64, bwStatsBitrateIn1m Counter64, bwStatsBitrateOut1m Counter64, bwStatsBitrateIn10m Counter64, bwStatsBitrateOut10m Counter64, bwStatsBitrateIn1h Counter64, bwStatsBitrateOut1h Counter64 } bwStatsIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object uniquely identifies this bwStats entry." ::= { bwStatsEntry 1 } bwStatsEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Bandwidth statistics enabled or disabled for this port." ::= { bwStatsEntry 2 } bwStatsBitrateIn10s OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current average input traffic for the last 10 seconds. This value is calculated via periodic sampling of the port counters And will be updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 3 } bwStatsBitrateOut10s OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current average output traffic for the last 10 seconds. This value is calculated via periodic sampling of the port counters And will be updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 4 } bwStatsBitrateIn1m OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current moving average input traffic for the last minute. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 5 } bwStatsBitrateOut1m OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current moving average output traffic for the last minute. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 6 } bwStatsBitrateIn10m OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current moving average input traffic for the last 10 minutes. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 7 } bwStatsBitrateOut10m OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current moving average output traffic for the last 10 minutes. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 8 } bwStatsBitrateIn1h OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current moving average input traffic for the last hour. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 9 } bwStatsBitrateOut1h OBJECT-TYPE SYNTAX Counter64 UNITS "Bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The current moving average output traffic for the last hour. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included)." ::= { bwStatsEntry 10 } -- ------------------------------------------------------------- -- Link Group -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Link: Layer 2 VLAN Group -- ## No VLAN functionality included yet -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Link: Layer 2 QoS Group -- ------------------------------------------------------------- l2QosVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF L2QosVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing VLAN priority settings for existing VLANs." ::= { l2Qos 1 } l2QosVlanEntry OBJECT-TYPE SYNTAX L2QosVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The row in the l2QosVlanTable containing per VLAN priority settings." INDEX { l2QosVlanId } ::= { l2QosVlanTable 1 } L2QosVlanEntry ::= SEQUENCE { l2QosVlanId VlanId, vlanPriorityEnabled TruthValue, vlanPriorityLevel Integer32 } l2QosVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-only STATUS current DESCRIPTION "This index should be mapped to the VLAN ID of Q-bridge MIB." ::= { l2QosVlanEntry 1 } vlanPriorityEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enable (true) or disable (false) VLAN priority for this VLAN." ::= { l2QosVlanEntry 2 } vlanPriorityLevel OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN priority level for this VLAN. 0 is lowest and 7 is highest priority." ::= { l2QosVlanEntry 3 } -- ------------------------------------------------------------- -- Link: Layer 2 Port Priority Group -- ------------------------------------------------------------- l2QosPortTable OBJECT-TYPE SYNTAX SEQUENCE OF L2QosPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing per port piority settings for LAN ports" ::= { l2Qos 2 } l2QosPortEntry OBJECT-TYPE SYNTAX L2QosPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The row in the l2QosPortTable containing per port priority settings." INDEX { l2QosPortIfIndex } ::= { l2QosPortTable 1 } L2QosPortEntry ::= SEQUENCE { l2QosPortIfIndex InterfaceIndex, l2QosPortIfName DisplayString, l2QosPortPriorityMode INTEGER, l2QosPortPriorityLevel Integer32 } l2QosPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This index should map to the port's ifIndex in the ifTable." ::= { l2QosPortEntry 1 } l2QosPortIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This name should map to the port's ifName in the ifXTable." ::= { l2QosPortEntry 2 } l2QosPortPriorityMode OBJECT-TYPE SYNTAX INTEGER { tag(1), -- Priority based on VLAN tag priority. ip(2), -- Priority based on IP ToS/DSCP. port(3) -- Priority based on Port priority. } MAX-ACCESS read-write STATUS current DESCRIPTION "The priority mode (tag, ip or port) to be used on this specific port. 1. (tag): Use the incoming packet's VLAN tag priority value to determine its priority. (Untagged packets will have their priority based on the configured port priority.) 2. (ip): Use the incoming packet's IP ToS/DSCP priority value to determine its priority. (Non-IP packets will have their priority based on the configured port priority.) 3. (port): Use the ingress port's configured priority to determine the packets priority." ::= { l2QosPortEntry 3 } l2QosPortPriorityLevel OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The port priority level for this port. 0 is lowest and 7 is highest priority." ::= { l2QosPortEntry 4 } -- ------------------------------------------------------------- -- Link: Frnt: Layer 2 FRNT Group -- ------------------------------------------------------------- frntv0Table OBJECT-TYPE SYNTAX SEQUENCE OF Frntv0Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing a list of FRNTv0 instances/rings." ::= { frntv0 1 } frntv0Entry OBJECT-TYPE SYNTAX Frntv0Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The row in the frntv0Table containing settings and status information for a specific FRNTv0 instance/ring." INDEX { frntv0InstanceId } ::= { frntv0Table 1 } Frntv0Entry ::= SEQUENCE { frntv0InstanceId Integer32, frntv0FocalPointEnabled TruthValue, frntv0Port1 DisplayString, frntv0Port2 DisplayString, frntv0Port1State INTEGER, frntv0Port2State INTEGER, frntv0RingStatus INTEGER, frntv0RowStatus RowStatus, frntv0TopologyChangeCount Integer32, frntv0TopologyTimeSinceLastChange TimeTicks, frntv0PortsSwapped TruthValue } frntv0InstanceId OBJECT-TYPE SYNTAX Integer32 (1..64) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The instance id of this FRNTv0 Ring (only of local significance to this unit)." ::= { frntv0Entry 1 } frntv0FocalPointEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "True(1) if this unit is configured as focal point for this FRNTv0 instance. False(2) if this unit is configured as member switch for this FRNTv0 instance." ::= { frntv0Entry 2 } frntv0Port1 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of FRNT port M in the FRNT port pair. In case the unit is configured as focal point and the ring is fully connected, it is port M that is put in BLOCKING." ::= { frntv0Entry 3 } frntv0Port2 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of FRNT port N in the FRNT port pair. In case of an edge in a FRNT bus rather than a node in a FRNT ring then port N shall be set to 'None' and it will be read as 'None'. In case the unit is configured as focal point and the ring is fully connected, it is port M that is put in BLOCKING." ::= { frntv0Entry 4 } frntv0Port1State OBJECT-TYPE SYNTAX INTEGER { disabled(1), -- Link down blocking(2), -- Link up, BLOCKING learning(4), -- Link up, LEARNING (invalid state for an FRNT ring port) forwarding(5) -- Link up, FORWARDING } MAX-ACCESS read-only STATUS current DESCRIPTION "Provides information about the status of FRNT port M. See frntv0RingStatus for more details." ::= { frntv0Entry 5} frntv0Port2State OBJECT-TYPE SYNTAX INTEGER { disabled(1), -- Link down blocking(2), -- Link up, BLOCKING learning(4), -- Link up, LEARNING (invalid state for an FRNT ring port) forwarding(5) -- Link up, FORWARDING } MAX-ACCESS read-only STATUS current DESCRIPTION "Provides information about the status of FRNT port N. See frntv0RingStatus for more details." ::= { frntv0Entry 6} frntv0RingStatus OBJECT-TYPE SYNTAX INTEGER { ring(1), bus(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Read ring status information. The answer is to be interpreted differently when asking a focal point or a member switch. Focal point (status of the whole FRNT topology): 1. ring mode: A focal point reports 'ring(1)' when the FRNT topology is intact. On a focal point this indicates OK. 2. bus mode: A focal point reports 'bus(2)' when it has detected an ERROR in the FRNT topology, i.e., the topology is broken. It can either be an error on any of its local FRNT ports (M or N), or elsewhere in the FRNT topology. Member switch (status of the member's local FRNT ports): 1. ring mode: A member switch reports 'ring(1)' when one or both of its FRNT ports are down or in blocking state. On a member switch this indicates an ERROR. 2. bus mode: A member switch reports 'bus(2)' when both its FRNT ports are in forwarding state. On a member switch this is an indication of OK, but it only has significance for this member switch, not the whole FRNT topology." ::= { frntv0Entry 7 } frntv0RowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this table entry." ::= { frntv0Entry 8 } frntv0TopologyChangeCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of transitions between bus/ring mode since FRNT was enabled." ::= { frntv0Entry 9 } frntv0TopologyTimeSinceLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the time that have passed since the last change of ring status." ::= { frntv0Entry 10 } frntv0PortsSwapped OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "FRNT can detect if the FRNT ports have been swapped. For example if port1 is connected to port1 on another FRNT unit. True(1) if the ports are swapped. False(2) if the ports are not swapped." ::= { frntv0Entry 11 } ---------------------------------------------------------------- -- Link: RiCo: Ring coupling and Dual-Homing status (read) ---------------------------------------------------------------- riCoStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RiCoStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing status for a list of RiCo and/or Dual Homing instances present on this unit." ::= { rico 1 } riCoStatusEntry OBJECT-TYPE SYNTAX RiCoStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Row in the riCoStatusTable that is containing settings and status information for a specific RiCo/Dual-Homing instance." INDEX { riCoStatusRingIdx, riCoStatusCouplingIdx, riCoStatusNodeId } ::= { riCoStatusTable 1 } RiCoStatusEntry ::= SEQUENCE { riCoStatusRingIdx Integer32, riCoStatusCouplingIdx Integer32, riCoStatusNodeId MacAddress, riCoStatusHelloInterval Integer32, riCoStatusHelloEffective Integer32 } riCoStatusRingIdx OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is always '0'." ::= { riCoStatusEntry 1 } riCoStatusCouplingIdx OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoStatusRingIdx)." ::= { riCoStatusEntry 2 } riCoStatusNodeId OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The unique ID of this RiCo node. A MAC address (typically the base MAC address) of this unit." ::= { riCoStatusEntry 3 } riCoStatusHelloInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Configured RiCo Ring Hello interval in milliseconds. Not applicable for Dual Homing instances (value '0')" ::= { riCoStatusEntry 4 } riCoStatusHelloEffective OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Effective RiCo Ring Hello interval in milliseconds. Shows negotiated Hello interval. Not applicable for Dual Homing instances (value '0')." ::= { riCoStatusEntry 5 } ---------------------------------------------------------------- -- Link: RiCo: Ring coupling and Dual-Homing uplink status (read) ---------------------------------------------------------------- riCoStatusUplinkTable OBJECT-TYPE SYNTAX SEQUENCE OF RiCoStatusUplinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing status of RiCo and Dual-Homing uplinks per link" ::= { rico 2 } riCoStatusUplinkEntry OBJECT-TYPE SYNTAX RiCoStatusUplinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The row in the riCoStatusUplinkTable containing status information for a specific RiCo or Dual-Homing uplink. For RiCo, status for all local uplinks, and for the best uplink of each RiCo peer is listed. For dual-homing, status for all local uplinks is listed." INDEX { riCoStatusUplinkRingIdx, riCoStatusUplinkCouplingIdx, riCoStatusUplinkNodeId, riCoStatusUplinkIfIndex } ::= { riCoStatusUplinkTable 1 } RiCoStatusUplinkEntry ::= SEQUENCE { riCoStatusUplinkRingIdx Integer32, riCoStatusUplinkCouplingIdx Integer32, riCoStatusUplinkNodeId MacAddress, riCoStatusUplinkIfIndex InterfaceIndex, riCoStatusUplinkStatus INTEGER, riCoStatusUplinkIfName DisplayString, riCoStatusUplinkPrio Integer32, riCoStatusUplinkPathCost Integer32, riCoStatusUplinkHelloInterval Integer32, riCoStatusUplinkHelloIntervalEffective Integer32, riCoStatusUplinkChangedCounter Integer32, riCoStatusUplinkSynchronized INTEGER, riCoStatusUplinkPreferred INTEGER, riCoStatusUplinkLocal TruthValue } riCoStatusUplinkRingIdx OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is always '0'." ::= { riCoStatusUplinkEntry 1 } riCoStatusUplinkCouplingIdx OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The instance id of this riCo Uplink" ::= { riCoStatusUplinkEntry 2 } riCoStatusUplinkNodeId OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The unique ID of the node, i.e., the MAC address of the node. For RiCo, this can be the (base) MAC of the local unit, or the MAC identifying a peer RiCo node. For Dual-Homing, this is the (base) MAC of the local unit." ::= { riCoStatusUplinkEntry 3 } riCoStatusUplinkIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the uplink port. - For local uplinks, this index corresponds to the port's index in the ifTable (IF-MIB). - For non-local uplinks, the value is not valid (value '0')." ::= { riCoStatusUplinkEntry 4 } riCoStatusUplinkStatus OBJECT-TYPE SYNTAX INTEGER { active(1), -- Uplink active backup(2), -- Uplink backup down(3) -- Uplink down } MAX-ACCESS read-only STATUS current DESCRIPTION "Uplink active (1), backup (2) or down (3)." ::= { riCoStatusUplinkEntry 5 } riCoStatusUplinkIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the interface used for this uplink." ::= { riCoStatusUplinkEntry 6 } riCoStatusUplinkPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Effective priority of this uplink. Based on configured priority and 'adjust' value (sticky uplink)." ::= { riCoStatusUplinkEntry 7 } riCoStatusUplinkPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current path cost for this uplink." ::= { riCoStatusUplinkEntry 8 } riCoStatusUplinkHelloInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Configured Ring Hello Interval for the RiCo node of this uplink. Not valid for Dual-Homing, value '0')" ::= { riCoStatusUplinkEntry 9 } riCoStatusUplinkHelloIntervalEffective OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Effective Ring Hello Interval for the RiCo node of this uplink. Not valid for Dual-Homing, value '0')" ::= { riCoStatusUplinkEntry 10 } riCoStatusUplinkChangedCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times this uplink changed its state" ::= { riCoStatusUplinkEntry 11 } riCoStatusUplinkSynchronized OBJECT-TYPE SYNTAX INTEGER { synchronized(1), notSynchronized(2), notApplicable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Synchronization status for this uplink: - synchronized(1): Synchronize enabled and ok - notSynchronized(2): Synchronize enabled and fails - notApplicable(3): Non-local RiCo uplink, or Dual-Homing uplink where Synchronize is disabled" ::= { riCoStatusUplinkEntry 12 } riCoStatusUplinkPreferred OBJECT-TYPE SYNTAX INTEGER { preferred(1), notPreferred(2), notApplicable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Preferred uplink status. Only valid for Dual-Homing uplinks whit synchronization enabled. - preferred(1): Dual-Homing uplink has status 'Preferred' - notPreferred(2): Dual-Homing uplink has status 'Not Preferred' - notApplicable(3): Uplink is either - a Dual-Homing uplink with synchronization disabled, or - a RiCo uplink (local or non-local)" ::= { riCoStatusUplinkEntry 13 } riCoStatusUplinkLocal OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Local(true) or global(false) instance" ::= { riCoStatusUplinkEntry 14 } ---------------------------------------------------------------- -- Link: RiCo: Ring coupling and Dual-Homing configure (write/create) ---------------------------------------------------------------- riCoCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF RiCoCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing a list of RiCo couplings." ::= { rico 3 } riCoCfgEntry OBJECT-TYPE SYNTAX RiCoCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The row in the riCoTable containing settings for a specific RiCo or Dual-Homing instance." INDEX { riCoCfgRingIdx, riCoCfgCouplingIdx } ::= { riCoCfgTable 1 } RiCoCfgEntry ::= SEQUENCE { riCoCfgRingIdx Integer32, riCoCfgCouplingIdx Integer32, riCoCfgEnabled TruthValue, riCoCfgHelloInterval Integer32, riCoCfgSynchronize INTEGER, riCoCfgRowStatus RowStatus } riCoCfgRingIdx OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is always '0'." ::= { riCoCfgEntry 1 } riCoCfgCouplingIdx OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS read-create STATUS current DESCRIPTION "The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoCfgRingIdx)." ::= { riCoCfgEntry 2 } riCoCfgEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the RiCo instance True (1) or False (2)" ::= { riCoCfgEntry 3 } riCoCfgHelloInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Configured RiCo Ring Hello interval in milliseconds. - Default: 100 milliseconds - Configurable in range: 50-1000 milliseconds - Not applicable for Dual Homing instances (value '0')" ::= { riCoCfgEntry 4 } riCoCfgSynchronize OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable Uplink synchronization. 'True' to enable, and 'False' to disable synchronization. Note: Only configurable for Dual-Homing Uplinks. For RiCo Uplinks, synchronization is always enabled." ::= { riCoCfgEntry 5 } riCoCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this table entry. This object can also be used to create or delete instances. At most 1 RiCo instance and at most 8 Dual-Homing instances can be created." ::= { riCoCfgEntry 6 } ---------------------------------------------------------------- -- Link: RiCo: RiCo and Dual-Homing uplink configure (write) ---------------------------------------------------------------- riCoCfgUplinkTable OBJECT-TYPE SYNTAX SEQUENCE OF RiCoCfgUplinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing RiCo and Dual-Homing uplinks and corresponding settings per link." ::= { rico 4 } riCoCfgUplinkEntry OBJECT-TYPE SYNTAX RiCoCfgUplinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The row in the riCoLinkTable containing settings and status information for a specific RiCo or Dual-Homing Uplink." INDEX { riCoCfgRingIdx, riCoCfgCouplingIdx, riCoCfgUplinkIfIndex } ::= { riCoCfgUplinkTable 1 } RiCoCfgUplinkEntry ::= SEQUENCE { riCoCfgUplinkRingIdx Integer32, riCoCfgUplinkCouplingIdx Integer32, riCoCfgUplinkIfIndex InterfaceIndex, riCoCfgUplinkPrio Integer32, riCoCfgUplinkAdjust Integer32, riCoCfgUplinkEchoTime Integer32, riCoCfgUplinkPathCost Integer32, riCoCfgUplinkRowStatus RowStatus } riCoCfgUplinkRingIdx OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is always '0'." ::= { riCoCfgUplinkEntry 1 } riCoCfgUplinkCouplingIdx OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS read-create STATUS current DESCRIPTION "The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoStatusRingIdx)." ::= { riCoCfgUplinkEntry 2 } riCoCfgUplinkIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The interface index of the uplink port. For local uplinks, this index corresponds to the port's index in the ifTable (IF-MIB)." ::= { riCoCfgUplinkEntry 3 } riCoCfgUplinkPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Configure priority for this uplink (128 as default). A lower value increases the chance to be elected as active uplink." ::= { riCoCfgUplinkEntry 4 } riCoCfgUplinkAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Configure adjust value for this uplink (sticky uplink). The effictive priority is reduced by the adjust value if the link becomes elected as active uplink. Default '0'." ::= { riCoCfgUplinkEntry 5 } riCoCfgUplinkEchoTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Uplink echo interval to be set for this uplink in milliseconds. Default: 200 ms Range: 20-1000 ms" ::= { riCoCfgUplinkEntry 6 } riCoCfgUplinkPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Path-cost to be set for this uplink. '0' means 'Auto', which lets path cost depend on speed and duplex of the uplink." ::= { riCoCfgUplinkEntry 7 } riCoCfgUplinkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this table entry." ::= { riCoCfgUplinkEntry 8 } ---------------------------------------------------------------- -- Link: LLDP: Custom TLV ---------------------------------------------------------------- lldpCtlvTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpCtlvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The LLDP custom TLV (Type 127) configuration table" ::= { lldpCtlv 1 } lldpCtlvEntry OBJECT-TYPE SYNTAX LldpCtlvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A custom TLV entry." INDEX { lldpCtlvIdx } ::= { lldpCtlvTable 1 } LldpCtlvEntry ::= SEQUENCE { lldpCtlvIdx INTEGER, lldpCtlvOui OCTET STRING, lldpCtlvSubType INTEGER, lldpCtlvInfo OCTET STRING, lldpCtlvRowStatus RowStatus } lldpCtlvIdx OBJECT-TYPE SYNTAX INTEGER (1..60) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of this custom TLV. Only of local significance." ::= { lldpCtlvEntry 1 } lldpCtlvOui OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Organizationally unique identifier (OUI), 3 hex-encoded bytes. Required." ::= { lldpCtlvEntry 2 } lldpCtlvSubType OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Organizationally defined subtype, one byte. Default: 0" ::= { lldpCtlvEntry 3 } lldpCtlvInfo OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Information/value part of custom TLV. 0-507 octets encoded as hex. Default: Empty" ::= { lldpCtlvEntry 4 } lldpCtlvRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this table entry. Used to create or delete a custom TLV entry." ::= { lldpCtlvEntry 5 } ---------------------------------------------------------------- -- Link: LLDP: Custom TLV port -> ctlvIndex mapping ---------------------------------------------------------------- lldpCtlvPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpCtlvPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table specifying which custom TLV(s) to transmit per port. Each row in the table maps a custom TLV to a port. Each custom TLV in the lldpCtlvTable can be mapped to one or more ports." ::= { lldpCtlv 2 } lldpCtlvPortEntry OBJECT-TYPE SYNTAX LldpCtlvPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry maps a custom TLV to a port." INDEX { lldpCtlvPortIdx, lldpCtlvIdx} ::= { lldpCtlvPortTable 1 } LldpCtlvPortEntry ::= SEQUENCE { lldpCtlvPortIdx INTEGER, lldpCtlvPortCtlvIdx INTEGER, lldpCtlvPortRowStatus RowStatus } lldpCtlvPortIdx OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The logical number of the port. This is the same number as the dot1dBasePort (dot1dBasePortTable of BRIDGE-MIB) for this port." ::= { lldpCtlvPortEntry 1 } lldpCtlvPortCtlvIdx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Custom TLV index (lldpCtlvTable)" ::= { lldpCtlvPortEntry 2 } lldpCtlvPortRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this table entry. Used to create or delete a 'custom TLV to port' mapping." ::= { lldpCtlvPortEntry 3 } ---------------------------------------------------------------- -- Link: LLDP: Remote Custom TLV ---------------------------------------------------------------- lldpRemCtlvTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpRemCtlvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table listing all custom TLV(s) received. Each entry represents a custom TLV received on a specific port from individual neighbours. Entries are removed when the TTL of the LLDP message expires, and will be removed/replaced when a new LLDP message from the same neighbour is received." ::= { lldpCtlv 3 } lldpRemCtlvEntry OBJECT-TYPE SYNTAX LldpRemCtlvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Custom TLV received on a port." INDEX { lldpRemCtlvLocalPort, lldpRemCtlvMacAddress, lldpRemCtlvOui, lldpRemCtlvSubType } ::= { lldpRemCtlvTable 1 } LldpRemCtlvEntry ::= SEQUENCE { lldpRemCtlvLocalPort INTEGER, lldpRemCtlvMacAddress MacAddress, lldpRemCtlvOui OCTET STRING, lldpRemCtlvSubType INTEGER, lldpRemCtlvInfo OCTET STRING } lldpRemCtlvLocalPort OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The logical number of the local port receiving this custom TLV. This is the same number as the dot1dBasePort (dot1dBasePortTable of BRIDGE-MIB) for this port." ::= { lldpRemCtlvEntry 1 } lldpRemCtlvMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the neighbour node sending this custom TLV." ::= { lldpRemCtlvEntry 2 } lldpRemCtlvOui OBJECT-TYPE SYNTAX OCTET STRING (SIZE (3)) MAX-ACCESS read-only STATUS current DESCRIPTION "Organizationally unique identifier (OUI), 3 hex-encoded bytes." ::= { lldpRemCtlvEntry 3 } lldpRemCtlvSubType OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Organizationally defined subtype, one byte." ::= { lldpRemCtlvEntry 4 } lldpRemCtlvInfo OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Information/value part of custom TLV. 0-507 octets encoded as hex." ::= { lldpRemCtlvEntry 5 } -- ------------------------------------------------------------- -- Link: IGMP Snooping Group -- ------------------------------------------------------------- igmpSnoopingQuerierMode OBJECT-TYPE SYNTAX INTEGER { auto(1), -- autonegotiate querier role querier(2), -- always act as querier proxy(3) -- operate in proxy querier mode } MAX-ACCESS read-write STATUS current DESCRIPTION "The querierMode object controls the querier mode an IGMP snooping switch will operate in on IGMP Snooping enabled VLANs. If the switch does not have an IP address on a certain VLAN, the switch will act in proxy querier mode irrespective of the querierMode setting. 1. Autonegotiate querier. The switch will become querier on a VLAN unless it hears IGMP queries on that VLAN from device with lower IP address. 2. Force querier role. The switch will act as querier on every VLAN where IGMP snooping is enabled. 3. Operate in proxy querier mode." ::= { igmpSnooping 1 } igmpSnoopingQuerierInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The IGMP Querier Interval (seconds). This interval will be used on all interfaces where this unit acts as IGMP Querier, unless multicast routing protocol specific or interface specific querier setting exist. Currently, the following interval values are valid: 12, 30, 70 and 150 (seconds)." ::= { igmpSnooping 2 } staticMulticastRouterPorts OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This is a comma-separated list of (LAN)port names, which specifies statically configured 'multicast router ports'. All layer-2 multicast traffic (known and unknown) should be forwarded onto multicast router ports." ::= { igmpSnooping 3 } currentMulticastRouterPorts OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is a comma-separated list of portnames, which lists all ports operating as multicast router ports - both dynamically discovered (e.g., by reception of IGMP Queries) or statically configured multicast router ports. All (layer-2) multicast traffic (known and unknown) should be forwarded onto multicast router ports." ::= { igmpSnooping 4 } igmpSnoopingVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopingVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of configuration entries for VLAN specific IGMP Snooping objects." ::= { igmpSnooping 5 } igmpSnoopingVlanEntry OBJECT-TYPE SYNTAX IgmpSnoopingVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An IGMP Snooping VLAN entry contains IGMP Snooping objects relevant for IGMP Snooping management per VLAN." INDEX { igmpSnoopingVlanId } ::= { igmpSnoopingVlanTable 1 } IgmpSnoopingVlanEntry ::= SEQUENCE { igmpSnoopingVlanId VlanId, igmpSnoopingEnabled TruthValue } igmpSnoopingVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-only STATUS current DESCRIPTION "This index should match corresponding VLAN ID of Q-bridge MIB." ::= { igmpSnoopingVlanEntry 1 } igmpSnoopingEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP Snooping enabled or disabled on this particular VLAN." ::= { igmpSnoopingVlanEntry 2 } -- ------------------------------------------------------------- -- Net Group -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Net: Iface: ifaceInet4 Group -- ------------------------------------------------------------- inet4StaticDefaultGatewayAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP Address of statically configured default gateway. Setting the address to 0.0.0.0 means that there is 'no static default gateway' configured." ::= { ifaceInet4 1 } inet4BaseIfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF Inet4BaseIfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing base IPv4 settings per interface" ::= { ifaceInet4 2 } inet4BaseIfaceEntry OBJECT-TYPE SYNTAX Inet4BaseIfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry in ipv4Interface table. Each row holds IPv4 settings specific to this interface." INDEX { inet4BaseIfIndex } ::= { inet4BaseIfaceTable 1 } Inet4BaseIfaceEntry ::= SEQUENCE { inet4BaseIfIndex InterfaceIndex, inet4BaseIfName DisplayString, inet4BaseAddressMode INTEGER } inet4BaseIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group." ::= { inet4BaseIfaceEntry 1 } inet4BaseIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name matches the corresponding ifName in the ifXTable." ::= { inet4BaseIfaceEntry 2 } inet4BaseAddressMode OBJECT-TYPE SYNTAX INTEGER { static(1), -- Static IPv4 address dhcp(2) -- Use DHCP/Bootp to acquire IP address. } MAX-ACCESS read-write STATUS current DESCRIPTION "The IPv4 address assignment mode." ::= { inet4BaseIfaceEntry 3 } inet4StaticTable OBJECT-TYPE SYNTAX SEQUENCE OF Inet4StaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing settings for static IPv4 interfaces" ::= { ifaceInet4 3 } inet4StaticEntry OBJECT-TYPE SYNTAX Inet4StaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry in ipv4Interface table. Each row holds IPv4 settings specific to this interface." INDEX { inet4StatIfIndex } ::= { inet4StaticTable 1 } Inet4StaticEntry ::= SEQUENCE { inet4StatIfIndex InterfaceIndex, inet4StatIfName DisplayString, inet4StatAddress IpAddress, inet4StatNetmask IpAddress } inet4StatIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group." ::= { inet4StaticEntry 1 } inet4StatIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name matches the corresponding ifName in the ifXTable." ::= { inet4StaticEntry 2 } inet4StatAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Statically configured IPv4 address for this interface. Address 0.0.0.0 means that the interface is disabled." ::= { inet4StaticEntry 3 } inet4StatNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Netmask of statically assigned IP address." ::= { inet4StaticEntry 4 } -- ------------------------------------------------------------- -- Net: Iface: DHCP table -- ------------------------------------------------------------- inet4DhcpTable OBJECT-TYPE SYNTAX SEQUENCE OF Inet4DhcpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing settings for IPv4 interfaces using DHCP for address assignment" ::= { ifaceInet4 4 } inet4DhcpEntry OBJECT-TYPE SYNTAX Inet4DhcpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry in inet4Dhcp table. Each row holds DHCP settings specific to this interface." INDEX { inet4DhcpIfIndex } ::= { inet4DhcpTable 1 } Inet4DhcpEntry ::= SEQUENCE { inet4DhcpIfIndex InterfaceIndex, inet4DhcpIfName DisplayString, inet4DhcpClientId DisplayString } inet4DhcpIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group." ::= { inet4DhcpEntry 1 } inet4DhcpIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name matches the corresponding ifName in the ifXTable." ::= { inet4DhcpEntry 2 } inet4DhcpClientId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Client ID passed by DHCP client to DHCP server." ::= { inet4DhcpEntry 3 } -- ------------------------------------------------------------- -- Net: Iface: AddressConflict (addressConflict) -- ------------------------------------------------------------- addressConflictExists OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if there are any conflicts detected, False if there are no more conflicts detected." ::= { addressConflict 1 } addressConflictTable OBJECT-TYPE SYNTAX SEQUENCE OF AddressConflictEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list containing all IP and MAC address conflicts currently on the this device" ::={ addressConflict 2 } addressConflictEntry OBJECT-TYPE SYNTAX AddressConflictEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing details for the conflict" INDEX { addressConflictIndex } ::= { addressConflictTable 1} AddressConflictEntry ::= SEQUENCE { addressConflictIndex Integer32, addressConflictIfIndex InterfaceIndex, addressConflictIfName DisplayString, addressConflictType INTEGER, addressConflictMacAddress PhysAddress, addressConflictIPv4Address IpAddress, addressConflictTime TimeTicks } addressConflictIndex OBJECT-TYPE SYNTAX Integer32 (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value for each conflict." ::= { addressConflictEntry 1 } addressConflictIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Index of the interface on this device." ::= { addressConflictEntry 2 } addressConflictIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the interface on this device." ::= { addressConflictEntry 3 } addressConflictType OBJECT-TYPE SYNTAX INTEGER { ip(1), mac(2), ipAndMac(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of conflict: 1 : IP, 2 : MAC, 3 : IP & MAC" ::= { addressConflictEntry 4 } addressConflictMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the conflicting peer." ::= { addressConflictEntry 5 } addressConflictIPv4Address OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv4 address of the conflicting peer." ::= { addressConflictEntry 6 } addressConflictTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time (in seconds) elapsed since conflict was last detected." ::= { addressConflictEntry 7 } -- ------------------------------------------------------------- -- Net: TTDP Group -- ------------------------------------------------------------- etbnInhibitionEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "ETBN inhibition enabled or disabled." ::= { ttdp 1 } -- ------------------------------------------------------------- -- System Group -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- System: Services Group -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- System: Services: SNMP Group -- ------------------------------------------------------------- trapCommunity OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The trap community name which traps destined to defined traphost(s) are sent with." ::= { snmp 1 } trapHostTable OBJECT-TYPE SYNTAX SEQUENCE OF TrapHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of SNMP trap host." ::= { snmp 2 } trapHostEntry OBJECT-TYPE SYNTAX TrapHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about a specific SNMP trap host." INDEX { trapHostId} ::= { trapHostTable 1 } TrapHostEntry ::= SEQUENCE { trapHostId Integer32, trapHostAddressType InetAddressType, trapHostAddress InetAddress, trapHostRowStatus RowStatus } trapHostId OBJECT-TYPE SYNTAX Integer32 (1..64) MAX-ACCESS read-only STATUS current DESCRIPTION "The id of this SNMP Trap Host (only of local significance to this unit)." ::= { trapHostEntry 1 } trapHostAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Internet address by which the trap host is reachable." ::= { trapHostEntry 2 } trapHostAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address or Domain name for the trap host." ::= { trapHostEntry 3 } trapHostRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this table entry." ::= { trapHostEntry 4 } roCommunity OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The read-only community name used to by SNMPv1/v2 to read SNMP MIB parameters. The string 'Disabled' have a special meaning and cannot be used as roCommunity string. Reading: String 'Disabled' - The read-only community is disabled Otherwise the received string shows the current read-only community. Writing: String 'Disabled' - Disable the read-write community Otherwise the written string becomes the new read-only community." ::= { snmp 3 } rwCommunity OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Provides a mechanism to change or enable/disable the read-write community name used to by SNMPv1/v2 to read and set SNMP MIB parameters, however, for security reasons the configured value is never displayed. The strings 'Enabled' and 'Disabled' have special meanings and cannot be used as rwCommunity string. Reading: String 'Enabled' - A read-write community is configured String 'Disabled' - The read-write community is disabled. Writing: String 'Disabled' - Disable the read-write community Otherwise the written string becomes the new read-write community (this implies that the read-write community is enabled if it was earlier disabled. Note that enabling the read-write community via SNMP is only possible from SNMPv3." ::= { snmp 4 } -- ------------------------------------------------------------- -- System: Services: Web Group -- ------------------------------------------------------------- webEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Web daemon enabled or disabled." ::= { web 1 } -- ------------------------------------------------------------- -- System: Services: IPConfig Group -- ------------------------------------------------------------- ipconfigEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "IPConfig daemon enabled or disabled." ::= { ipconfig 1 } -- ------------------------------------------------------------- -- System: Services: SSH Group -- ------------------------------------------------------------- sshEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "SSH daemon enabled or disabled." ::= { ssh 1 } -- ------------------------------------------------------------- -- System: Services: LLDP Group -- ------------------------------------------------------------- lldpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "LLDP service enabled or disabled. - True: Enabling LLDP will enable the LLDP service with default settings. - False: Disabling LLDP will fully disable the LLDP service, remove any existing configuration, and disableaccess to any other LLDP OID in private MIB andin LLDP MIB." ::= { lldp 1 } lldpActivated OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Activate/deactivate LLDP configuration. - True: LLDP daemon enabled with existing configuration - False: LLDP daemon deactivated. LLDP configuration (lldpPortConfigTable) is kept and is still accessible. Configuration changes will not take effect until lldpActivated is 'True'." ::= { lldp 2 } -- ------------------------------------------------------------- -- System: STATISTICS Group: -- ------------------------------------------------------------- memoryAvail OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the amount of available memory in kb for the system." ::= { statistics 1 } -- ------------------------------------------------------------- -- System: STATISTICS : cpuLoadAvg Group: -- ------------------------------------------------------------- loadAvg1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays a the cpu load average over 1 minute. The value is displayed by taking the cpu load avgerage value and multiplying it with 100." ::= { cpuLoadAvg 1 } loadAvg5 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays a the cpu load average over 5 minutes. The value is displayed by taking the cpu load avgerage value and multiplying it with 100." ::= { cpuLoadAvg 2 } loadAvg15 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays a the cpu load average over 15 minute. The value is displayed by taking the cpu load avgerage value and multiplying it with 100." ::= { cpuLoadAvg 3 } -- ------------------------------------------------------------- -- System: eventSystem: -- ------------------------------------------------------------- summaryAlarmStatus OBJECT-TYPE SYNTAX INTEGER { warning(1), -- At least one of the configured -- alarm sources reports alarm -- condition. ok(2) -- None of the configured alarm -- sources reports alarm condition. -- Alternatively, no alarm source -- is configured. } MAX-ACCESS read-only STATUS current DESCRIPTION "The summaryAlarmStatus reports ''warning'' when at least one of the configured alarm/event sources reports alarm condition. WeOS supports an extensive set of alarm/event sources and a flexible alarm handling framework. The sources affecting the summaryAlarmStatus are those configured to affect the unit's status LED, typically labeled ''ON'' and located on the unit's front panel." ::= { eventSystem 1 } summaryAlarmTrapEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable support for sending summaryAlarm traps. True(1) if summaryAlarm traps are enabled. False(2) if summaryAlarm traps are disabled. Traps will be sent if (and only if) the summaryAlarmStatus changes status ('warning => ok' or 'ok => warning')." ::= { eventSystem 2 } statusRelay OBJECT-TYPE SYNTAX INTEGER { warning(1), ok(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the current state of the statusRelay (DigitalOut)." ::= { eventSystem 3 } alarmStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The status for alarm triggers." ::= { eventSystem 4 } alarmStatusEntry OBJECT-TYPE SYNTAX AlarmStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about a specific alarm trigger." INDEX { alarmStatusTriggerId} ::= { alarmStatusTable 1 } AlarmStatusEntry ::= SEQUENCE { alarmStatusTriggerId INTEGER, alarmStatusTriggerType DisplayString, alarmStatusTriggerEnabled TruthValue, alarmStatusTriggerStatus INTEGER, alarmStatusTriggerStatusReason DisplayString} alarmStatusTriggerId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The id of alarm trigger" ::= { alarmStatusEntry 1 } alarmStatusTriggerType OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "A text string containing description about the trigger type" ::= { alarmStatusEntry 2 } alarmStatusTriggerEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the trigger is enabled or not" ::= { alarmStatusEntry 3 } alarmStatusTriggerStatus OBJECT-TYPE SYNTAX INTEGER {warning(1), ok(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "The actual alarm status for the trigger" ::= { alarmStatusEntry 4 } alarmStatusTriggerStatusReason OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "A text string containing status reason" ::= { alarmStatusEntry 5 } -- ------------------------------------------------------------- -- System: check: -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- System: check: configurationHash Group -- ------------------------------------------------------------- startupConfigurationHash OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A SHA-1 hash of the saved startup configuration." ::= { integrity 1 } runningConfigurationHash OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A SHA-1 hash of the current running configuration." ::= { integrity 2 } -- ------------------------------------------------------------- -- Notification group -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Notification: Sensor -- ------------------------------------------------------------- digitalInHigh NOTIFICATION-TYPE OBJECTS { entPhysicalName, entPhySensorValue } STATUS current DESCRIPTION "Notification associated with digitalIn sensor state. Sensor is of type TruthValue. The 'entPhySensorValue' should always have value 'true(1)' in a digitalInHigh trap, indicating that the voltage level is above the required threshold (logical 1)." ::= { sensorNotificationPrefix 1 } digitalInLow NOTIFICATION-TYPE OBJECTS { entPhysicalName, entPhySensorValue } STATUS current DESCRIPTION "Notification associated with digitalIn sensor state. Sensor is of type TruthValue. The 'entPhySensorValue' should always have value 'false(2)' in a digitalInLow trap, indicating that the voltage level is below the required threshold (logical 0)." ::= { sensorNotificationPrefix 2 } powerSupplyHigh NOTIFICATION-TYPE OBJECTS { entPhysicalName, entPhySensorValue } STATUS current DESCRIPTION "Notification associated with power supply sensor state. Sensor is of type TruthValue The 'entPhySensorValue' should always have value 'true(1)' in a powerSupplyHigh trap, indicating that the voltage level is above the required threshold." ::= { sensorNotificationPrefix 3 } powerSupplyLow NOTIFICATION-TYPE OBJECTS { entPhysicalName, entPhySensorValue } STATUS current DESCRIPTION "Notification associated with power supply sensor state. Sensor is of type TruthValue The 'entPhySensorValue' should always have value 'false(2)' in a powerSupplyLow trap, indicating that the voltage level is below the required threshold." ::= { sensorNotificationPrefix 4 } temperatureHigh NOTIFICATION-TYPE OBJECTS { entPhysicalName, entPhySensorValue, entPhySensorType, entPhySensorScale, entPhySensorPrecision } STATUS current DESCRIPTION "Notification associated with temperature sensor state. Sensor is of type 'Celsius'. The 'entPhySensorValue' shows the temperature value at the time the alarm system detected that the temperature had rised to or passed beyond the configured alarm rising threshold; except for temperatureHigh alarms at system startup, this would typically be equal to the temperature configured as the alarm rising threshold." ::= { sensorNotificationPrefix 5 } temperatureLow NOTIFICATION-TYPE OBJECTS { entPhysicalName, entPhySensorValue, entPhySensorType, entPhySensorScale, entPhySensorPrecision } STATUS current DESCRIPTION "Notification associated with temperature sensor state. Sensor is of type 'Celsius'. The 'entPhySensorValue' shows the temperature value at the time the alarm system detected that the temperature had fallen to or passed below the configured alarm falling threshold; except for temperatureLow alarms at system startup, this would typically be equal to the temperature configured as the alarm falling threshold." ::= { sensorNotificationPrefix 6 } -- ------------------------------------------------------------- -- Notification: Frnt -- ------------------------------------------------------------- frntv0RingUp NOTIFICATION-TYPE OBJECTS { frntv0InstanceId, frntv0FocalPointEnabled, frntv0RingStatus, frntv0Port1, frntv0Port1State, frntv0Port2, frntv0Port2State } STATUS current DESCRIPTION "Notification associated with FRNTv0 ring status. The 'frntv0RingStatus' should always have value 'ring(1)' in an frntv0RingUp trap. Note that a focal point can detect both local failures and elsewhere in the FRNT ring, while a member switch is only able to detect local failures." ::= { frntNotificationPrefix 1 } frntv0RingDown NOTIFICATION-TYPE OBJECTS { frntv0InstanceId, frntv0FocalPointEnabled, frntv0RingStatus, frntv0Port1, frntv0Port1State, frntv0Port2, frntv0Port2State } STATUS current DESCRIPTION "Notification associated with FRNTv0 ring status. The 'frntv0RingStatus' should always have value 'bus(2)' in an frntv0RingDown trap. Note that a focal point can detect both local failures and elsewhere in the FRNT ring, while a member switch is only able to detect local failures." ::= { frntNotificationPrefix 2 } -- ------------------------------------------------------------- -- Notification: lff -- ------------------------------------------------------------- lffRemoteUp NOTIFICATION-TYPE OBJECTS { lffPortIfName, lffStatus } STATUS current DESCRIPTION "Notification associated with link fault forward of remote (Ethernet) link over an intermediate (SHDSL) link. The 'lffStatus' should always have value 'remoteUp(4)' in a lffRemoteUp, indicating that remote (Ethernet) link is up." ::= { lffNotificationPrefix 1 } lffRemoteFail NOTIFICATION-TYPE OBJECTS { lffPortIfName, lffStatus } STATUS current DESCRIPTION "Notification associated with link fault forward of remote (Ethernet) link over an intermediate (SHDSL) link. The 'lffStatus' will show value - 'remoteDown(3)' when information that the remote (Ethernet) link is down is available. - 'unknown(2)' when there is no information about the state of the remote available, typically because the intermediate (SHDSL) link is down." ::= { lffNotificationPrefix 2 } -- ------------------------------------------------------------- -- Notification: Generic -- ------------------------------------------------------------- summaryStatusOK NOTIFICATION-TYPE OBJECTS { summaryAlarmStatus } STATUS current DESCRIPTION "Notification that _none_ of the configured alarm sources reports a bad state, i.e., - that the summaryAlarmStatus has _shifted_ from 'Warning (1)' to 'Ok (2)', or - that the unit started up with summaryStatus 'Ok (2)'." ::= { genericNotificationPrefix 1 } summaryStatusWarning NOTIFICATION-TYPE OBJECTS { summaryAlarmStatus } STATUS current DESCRIPTION "Notification that at least one of the configured alarm sources reports a bad state, i.e., - that the summaryAlarmStatus has _shifted_ from 'Ok (2)' to 'Warning (1)', or - that the unit started up with summaryStatus 'Warning (1)'." ::= { genericNotificationPrefix 2 } -- ------------------------------------------------------------- -- Notification: DDM -- ------------------------------------------------------------- ddmVoltageHigh NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortVoltage } STATUS current DESCRIPTION "Notification associated with DDM voltage sensor state. The 'sfpDdmPortVoltage' shows the voltage value at the time the alarm system detected that the voltage had rised to or passed beyond the configured alarm rising threshold." ::= { ddmNotificationPrefix 1 } ddmVoltageLow NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortVoltage } STATUS current DESCRIPTION "Notification associated with DDM voltage sensor state. The 'sfpDdmPortVoltage' shows the voltage value at the time the alarm system detected that the voltage had fallen to or passed below the configured alarm falling threshold." ::= { ddmNotificationPrefix 2 } ddmTemperatureHigh NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortTemperature } STATUS current DESCRIPTION "Notification associated with DDM temperature sensor state. The 'sfpDdmPortTemperature' shows the temperature value at the time the alarm system detected that the temperature had rised to or passed beyond the configured alarm rising threshold." ::= { ddmNotificationPrefix 3 } ddmTemperatureLow NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortTemperature } STATUS current DESCRIPTION "Notification associated with DDM temperature sensor state. The 'sfpDdmPortTemperature' shows the temperature value at the time the alarm system detected that the temperature had fallen to or passed below the configured alarm falling threshold." ::= { ddmNotificationPrefix 4 } ddmBiasCurrentHigh NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortBiasCurrent } STATUS current DESCRIPTION "Notification associated with DDM transmitt bias current sensor state. The 'sfpDdmPortBiasCurrent' shows the bias current value at the time the alarm system detected that the bias current had rised to or passed beyond the configured alarm rising threshold." ::= { ddmNotificationPrefix 5 } ddmBiasCurrentLow NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortBiasCurrent } STATUS current DESCRIPTION "Notification associated with DDM transmitt bias current sensor state. The 'sfpDdmPortBiasCurrent' shows the bias current value at the time the alarm system detected that the bias current had fallen to or passed below the configured alarm falling threshold." ::= { ddmNotificationPrefix 6 } ddmTxPowerHigh NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortTxPower } STATUS current DESCRIPTION "Notification associated with DDM transmitt power sensor state. The 'sfpDdmPortTxPower' shows the power value at the time the alarm system detected that the power had rised to or passed beyond the configured alarm rising threshold." ::= { ddmNotificationPrefix 7 } ddmTxPowerLow NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortTxPower } STATUS current DESCRIPTION "Notification associated with DDM transmitt power sensor state. The 'sfpDdmPortTxPower' shows the power value at the time the alarm system detected that the power had fallen to or passed below the configured alarm falling threshold." ::= { ddmNotificationPrefix 8 } ddmRxPowerHigh NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortRxPower } STATUS current DESCRIPTION "Notification associated with DDM receiving power sensor state. The 'sfpDdmPortRxPower' shows the power value at the time the alarm system detected that the power had rised to or passed beyond the configured alarm rising threshold." ::= { ddmNotificationPrefix 9 } ddmRxPowerLow NOTIFICATION-TYPE OBJECTS { sfpDdmPortIfIndex, sfpDdmPortIfName, sfpDdmPortRxPower } STATUS current DESCRIPTION "Notification associated with DDM receiving power sensor state. The 'sfpDdmPortRxPower' shows the power value at the time the alarm system detected that the power had fallen to or passed below the configured alarm falling threshold." ::= { ddmNotificationPrefix 10 } -- ------------------------------------------------------------- -- Notification: Address Conflict (addressConflict) -- ------------------------------------------------------------- addressConflictDetected NOTIFICATION-TYPE OBJECTS { addressConflictIfIndex, addressConflictIfName, addressConflictType, addressConflictMacAddress, addressConflictIPv4Address } STATUS current DESCRIPTION "An Address Conflict have been detected." ::= { conflictNotificationPrefix 1 } addressConflictCleared NOTIFICATION-TYPE OBJECTS { addressConflictIfIndex, addressConflictIfName, addressConflictType, addressConflictMacAddress, addressConflictIPv4Address } STATUS current DESCRIPTION "An Address Conflict have been resolved." ::= { conflictNotificationPrefix 2 } addressConflictOK NOTIFICATION-TYPE OBJECTS { addressConflictExists } STATUS current DESCRIPTION "There are no Address Conflicts. This trap is sent when the last conflict is resolved." ::= { conflictNotificationPrefix 3 } addressConflictWarning NOTIFICATION-TYPE OBJECTS { addressConflictExists } STATUS current DESCRIPTION "An address conflict exists. This trap is sent when the first address conflict is detected." ::= { conflictNotificationPrefix 4 } -- ------------------------------------------------------------- -- Notification: Other -- ------------------------------------------------------------- mrpRingClosed NOTIFICATION-TYPE OBJECTS { alarmStatusTriggerId } STATUS current DESCRIPTION "Notification associated with MRP ring state." ::= { otherNotificationPrefix 3 } mrpRingOpen NOTIFICATION-TYPE OBJECTS { alarmStatusTriggerId } STATUS current DESCRIPTION "Notification associated with MRP ring state." ::= { otherNotificationPrefix 4 } -- ------------------------------------------------------------- -- Notification: RiCo status -- ------------------------------------------------------------- riCoUplinkUp NOTIFICATION-TYPE OBJECTS { riCoStatusUplinkNodeId, riCoStatusUplinkIfIndex, riCoStatusUplinkIfName, riCoStatusUplinkStatus } STATUS current DESCRIPTION "A RiCo or Dual Homing uplink has come up. The riCoStatusUplinkStatus shows if the link comes up in role Active or Backup." ::= { riCoNotificationPrefix 1 } riCoUplinkDown NOTIFICATION-TYPE OBJECTS { riCoStatusUplinkNodeId, riCoStatusUplinkIfIndex, riCoStatusUplinkIfName, riCoStatusUplinkStatus } STATUS current DESCRIPTION "A RiCo or Dual Homing uplink has gone down. The riCoStatusUplinkStatus shows 'Down'." ::= { riCoNotificationPrefix 2 } -- ------------------------------------------------------------- -- Notification: Ping -- ------------------------------------------------------------- pingTriggerOk NOTIFICATION-TYPE OBJECTS { alarmStatusTriggerId} STATUS current DESCRIPTION "Notification associated with ping trigger status." ::= { pingNotificationPrefix 1 } pingTriggerWarning NOTIFICATION-TYPE OBJECTS { alarmStatusTriggerId} STATUS current DESCRIPTION "Notification associated with ping trigger status." ::= { pingNotificationPrefix 2 } END